[PATCH 0/4] ARM: dts: sun7i: Devicetree improvements for the Wexler TAB7200

[PATCH 0/4] ARM: dts: sun7i: Devicetree improvements for the Wexler TAB7200

[Aleksei Mamlin]

Hi Maxime,
This is a batch of patches with devicetree improvements for Wexler TAB7200 tablet.

The first one add Goodix GT911 touchscreen node to dts.
The second add PWM node, which need for LCD backlight.
The third add LCD backlight support via PWM.
The last add PA gpio pin for controlling external amplifiers.

The touchscreen patch depends on "Goodix touchscreen enhancements" [1]
and "Input: goodix - add axis swapping and axis inversion support" [2]
patchsets. Both merged into Dmitry Torokhov's input tree (goodix branch)

[1] https://lkml.org/lkml/2015/11/19/241
[2] https://lkml.org/lkml/2015/11/21/44

Aleksei Mamlin (4):
  ARM: dts: sun7i: Enable touchscreen on Wexler TAB7200 tablet
  ARM: dts: sun7i: Enable PWM controller on Wexler TAB7200 tablet
  ARM: dts: sun7i: Add backlight node to Wexler TAB7200 tablet
  ARM: dts: sun7i: Add PA gpio pin to Wexler TAB7200 tablet

 arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 53 ++++++++++++++++++++++++++
 1 file changed, 53 insertions(+)

-- 
2.4.10

[PATCH 0/4] ARM: dts: sun7i: Devicetree improvements for the Wexler TAB7200

[Aleksei Mamlin]

Hi Maxime,
This is a batch of patches with devicetree improvements for Wexler TAB7200 tablet.

The first one add Goodix GT911 touchscreen node to dts.
The second add PWM node, which need for LCD backlight.
The third add LCD backlight support via PWM.
The last add PA gpio pin for controlling external amplifiers.

The touchscreen patch depends on "Goodix touchscreen enhancements" [1]
and "Input: goodix - add axis swapping and axis inversion support" [2]
patchsets. Both merged into Dmitry Torokhov's input tree (goodix branch)

[1] https://lkml.org/lkml/2015/11/19/241
[2] https://lkml.org/lkml/2015/11/21/44

Aleksei Mamlin (4):
  ARM: dts: sun7i: Enable touchscreen on Wexler TAB7200 tablet
  ARM: dts: sun7i: Enable PWM controller on Wexler TAB7200 tablet
  ARM: dts: sun7i: Add backlight node to Wexler TAB7200 tablet
  ARM: dts: sun7i: Add PA gpio pin to Wexler TAB7200 tablet

 arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 53 ++++++++++++++++++++++++++
 1 file changed, 53 insertions(+)

-- 
2.4.10

[PATCH 1/4] ARM: dts: sun7i: Enable touchscreen on Wexler TAB7200 tablet

[Aleksei Mamlin]

Add a node for the Goodix GT911 touchscreen found on the Wexler TAB7200 tablet

Signed-off-by: Aleksei Mamlin <mamlinav-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
index 239b5d2..ec3b837 100644
--- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
+++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
@@ -102,6 +102,18 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c2_pins_a>;
 	status = "okay";
+
+	gt911: touchscreen@5d {
+		compatible = "goodix,gt911";
+		reg = <0x5d>;
+		interrupt-parent = <&pio>;
+		interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>; /* EINT21 (PH21) */
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_reset_pin>;
+		irq-gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* INT (PH21) */
+		reset-gpios = <&pio 1 13 GPIO_ACTIVE_HIGH>; /* RST (PB13) */
+		touchscreen-swapped-x-y;
+	};
 };
 
 &lradc {
@@ -146,6 +158,13 @@
 };
 
 &pio {
+	ts_reset_pin: ts_reset_pin@0 {
+		allwinner,pins = "PB13";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
 	usb0_id_detect_pin: usb0_id_detect_pin@0 {
 		allwinner,pins = "PH4";
 		allwinner,function = "gpio_in";
-- 
2.4.10

[PATCH 1/4] ARM: dts: sun7i: Enable touchscreen on Wexler TAB7200 tablet

[Aleksei Mamlin]

Add a node for the Goodix GT911 touchscreen found on the Wexler TAB7200 tablet

Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
---
 arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
index 239b5d2..ec3b837 100644
--- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
+++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
@@ -102,6 +102,18 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c2_pins_a>;
 	status = "okay";
+
+	gt911: touchscreen at 5d {
+		compatible = "goodix,gt911";
+		reg = <0x5d>;
+		interrupt-parent = <&pio>;
+		interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>; /* EINT21 (PH21) */
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_reset_pin>;
+		irq-gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* INT (PH21) */
+		reset-gpios = <&pio 1 13 GPIO_ACTIVE_HIGH>; /* RST (PB13) */
+		touchscreen-swapped-x-y;
+	};
 };
 
 &lradc {
@@ -146,6 +158,13 @@
 };
 
 &pio {
+	ts_reset_pin: ts_reset_pin at 0 {
+		allwinner,pins = "PB13";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
 	usb0_id_detect_pin: usb0_id_detect_pin at 0 {
 		allwinner,pins = "PH4";
 		allwinner,function = "gpio_in";
-- 
2.4.10

Re: [PATCH 1/4] ARM: dts: sun7i: Enable touchscreen on Wexler TAB7200 tablet

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 1347 bytes --]

Hi,

On Fri, Dec 18, 2015 at 11:51:50AM +0300, Aleksei Mamlin wrote:
> Add a node for the Goodix GT911 touchscreen found on the Wexler TAB7200 tablet
> 
> Signed-off-by: Aleksei Mamlin <mamlinav-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
>  arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 19 +++++++++++++++++++
>  1 file changed, 19 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> index 239b5d2..ec3b837 100644
> --- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> +++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> @@ -102,6 +102,18 @@
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&i2c2_pins_a>;
>  	status = "okay";
> +
> +	gt911: touchscreen@5d {
> +		compatible = "goodix,gt911";
> +		reg = <0x5d>;
> +		interrupt-parent = <&pio>;
> +		interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>; /* EINT21 (PH21) */
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&ts_reset_pin>;
> +		irq-gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* INT (PH21) */

It seems odd that you need both irq-gpios and interrupts. These two
are completely redundant, and you should even actually use only one in
your driver, since the second request_irq will fail.

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[PATCH 1/4] ARM: dts: sun7i: Enable touchscreen on Wexler TAB7200 tablet

[Maxime Ripard]

Hi,

On Fri, Dec 18, 2015 at 11:51:50AM +0300, Aleksei Mamlin wrote:
> Add a node for the Goodix GT911 touchscreen found on the Wexler TAB7200 tablet
> 
> Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
> ---
>  arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 19 +++++++++++++++++++
>  1 file changed, 19 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> index 239b5d2..ec3b837 100644
> --- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> +++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> @@ -102,6 +102,18 @@
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&i2c2_pins_a>;
>  	status = "okay";
> +
> +	gt911: touchscreen at 5d {
> +		compatible = "goodix,gt911";
> +		reg = <0x5d>;
> +		interrupt-parent = <&pio>;
> +		interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>; /* EINT21 (PH21) */
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&ts_reset_pin>;
> +		irq-gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* INT (PH21) */

It seems odd that you need both irq-gpios and interrupts. These two
are completely redundant, and you should even actually use only one in
your driver, since the second request_irq will fail.

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20151218/18d43e8e/attachment.sig>

Re: [PATCH 1/4] ARM: dts: sun7i: Enable touchscreen on Wexler TAB7200 tablet

[Aleksei Mamlin]

[-- Attachment #1: Type: text/plain, Size: 2278 bytes --]

2015-12-19 0:25 GMT+03:00 Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>:

> Hi,
>
> On Fri, Dec 18, 2015 at 11:51:50AM +0300, Aleksei Mamlin wrote:
> > Add a node for the Goodix GT911 touchscreen found on the Wexler TAB7200
> tablet
> >
> > Signed-off-by: Aleksei Mamlin <mamlinav-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> > ---
> >  arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 19 +++++++++++++++++++
> >  1 file changed, 19 insertions(+)
> >
> > diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> > index 239b5d2..ec3b837 100644
> > --- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> > +++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> > @@ -102,6 +102,18 @@
> >       pinctrl-names = "default";
> >       pinctrl-0 = <&i2c2_pins_a>;
> >       status = "okay";
> > +
> > +     gt911: touchscreen@5d {
> > +             compatible = "goodix,gt911";
> > +             reg = <0x5d>;
> > +             interrupt-parent = <&pio>;
> > +             interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>; /* EINT21
> (PH21) */
> > +             pinctrl-names = "default";
> > +             pinctrl-0 = <&ts_reset_pin>;
> > +             irq-gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* INT (PH21) */
>
> It seems odd that you need both irq-gpios and interrupts. These two
> are completely redundant, and you should even actually use only one in
> your driver, since the second request_irq will fail.
>
>
We need both interrupts and irq-gpios because the driver uses the interrupt
gpio pin as output to reset the device. See bindings documentation [1]

[1]
https://git.kernel.org/cgit/linux/kernel/git/dtor/input.git/tree/Documentation/devicetree/bindings/input/touchscreen/goodix.txt?h=goodix


Thanks!
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux, Kernel and Android engineering
> http://free-electrons.com
>



-- 
Thanks and regards,
Aleksei Mamlin

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.

[-- Attachment #2: Type: text/html, Size: 4057 bytes --]

Re: [PATCH 1/4] ARM: dts: sun7i: Enable touchscreen on Wexler TAB7200 tablet

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 2110 bytes --]

On Sat, Dec 19, 2015 at 06:11:40PM +0300, Aleksei Mamlin wrote:
> 2015-12-19 0:25 GMT+03:00 Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>:
> 
> > Hi,
> >
> > On Fri, Dec 18, 2015 at 11:51:50AM +0300, Aleksei Mamlin wrote:
> > > Add a node for the Goodix GT911 touchscreen found on the Wexler TAB7200
> > tablet
> > >
> > > Signed-off-by: Aleksei Mamlin <mamlinav-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> > > ---
> > >  arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 19 +++++++++++++++++++
> > >  1 file changed, 19 insertions(+)
> > >
> > > diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> > b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> > > index 239b5d2..ec3b837 100644
> > > --- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> > > +++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> > > @@ -102,6 +102,18 @@
> > >       pinctrl-names = "default";
> > >       pinctrl-0 = <&i2c2_pins_a>;
> > >       status = "okay";
> > > +
> > > +     gt911: touchscreen@5d {
> > > +             compatible = "goodix,gt911";
> > > +             reg = <0x5d>;
> > > +             interrupt-parent = <&pio>;
> > > +             interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>; /* EINT21
> > (PH21) */
> > > +             pinctrl-names = "default";
> > > +             pinctrl-0 = <&ts_reset_pin>;
> > > +             irq-gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* INT (PH21) */
> >
> > It seems odd that you need both irq-gpios and interrupts. These two
> > are completely redundant, and you should even actually use only one in
> > your driver, since the second request_irq will fail.
> >
> >
> We need both interrupts and irq-gpios because the driver uses the interrupt
> gpio pin as output to reset the device. See bindings documentation [1]
> 
> [1]
> https://git.kernel.org/cgit/linux/kernel/git/dtor/input.git/tree/Documentation/devicetree/bindings/input/touchscreen/goodix.txt?h=goodix

Hmm, indeed, and even the documentation is confusing.

Thanks,
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[PATCH 1/4] ARM: dts: sun7i: Enable touchscreen on Wexler TAB7200 tablet

[Maxime Ripard]

On Sat, Dec 19, 2015 at 06:11:40PM +0300, Aleksei Mamlin wrote:
> 2015-12-19 0:25 GMT+03:00 Maxime Ripard <maxime.ripard@free-electrons.com>:
> 
> > Hi,
> >
> > On Fri, Dec 18, 2015 at 11:51:50AM +0300, Aleksei Mamlin wrote:
> > > Add a node for the Goodix GT911 touchscreen found on the Wexler TAB7200
> > tablet
> > >
> > > Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
> > > ---
> > >  arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 19 +++++++++++++++++++
> > >  1 file changed, 19 insertions(+)
> > >
> > > diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> > b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> > > index 239b5d2..ec3b837 100644
> > > --- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> > > +++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> > > @@ -102,6 +102,18 @@
> > >       pinctrl-names = "default";
> > >       pinctrl-0 = <&i2c2_pins_a>;
> > >       status = "okay";
> > > +
> > > +     gt911: touchscreen at 5d {
> > > +             compatible = "goodix,gt911";
> > > +             reg = <0x5d>;
> > > +             interrupt-parent = <&pio>;
> > > +             interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>; /* EINT21
> > (PH21) */
> > > +             pinctrl-names = "default";
> > > +             pinctrl-0 = <&ts_reset_pin>;
> > > +             irq-gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* INT (PH21) */
> >
> > It seems odd that you need both irq-gpios and interrupts. These two
> > are completely redundant, and you should even actually use only one in
> > your driver, since the second request_irq will fail.
> >
> >
> We need both interrupts and irq-gpios because the driver uses the interrupt
> gpio pin as output to reset the device. See bindings documentation [1]
> 
> [1]
> https://git.kernel.org/cgit/linux/kernel/git/dtor/input.git/tree/Documentation/devicetree/bindings/input/touchscreen/goodix.txt?h=goodix

Hmm, indeed, and even the documentation is confusing.

Thanks,
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20151221/d7bf2b64/attachment-0001.sig>

Re: [linux-sunxi] Re: [PATCH 1/4] ARM: dts: sun7i: Enable touchscreen on Wexler TAB7200 tablet

[Karsten Merker]

On Fri, Dec 18, 2015 at 10:25:25PM +0100, Maxime Ripard wrote:
> On Fri, Dec 18, 2015 at 11:51:50AM +0300, Aleksei Mamlin wrote:
> > Add a node for the Goodix GT911 touchscreen found on the Wexler TAB7200 tablet
> > 
> > Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
> > ---
> >  arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 19 +++++++++++++++++++
> >  1 file changed, 19 insertions(+)
> > 
> > diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> > index 239b5d2..ec3b837 100644
> > --- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> > +++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> > @@ -102,6 +102,18 @@
> >  	pinctrl-names = "default";
> >  	pinctrl-0 = <&i2c2_pins_a>;
> >  	status = "okay";
> > +
> > +	gt911: touchscreen@5d {
> > +		compatible = "goodix,gt911";
> > +		reg = <0x5d>;
> > +		interrupt-parent = <&pio>;
> > +		interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>; /* EINT21 (PH21) */
> > +		pinctrl-names = "default";
> > +		pinctrl-0 = <&ts_reset_pin>;
> > +		irq-gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* INT (PH21) */
> 
> It seems odd that you need both irq-gpios and interrupts. These two
> are completely redundant, and you should even actually use only one in
> your driver, since the second request_irq will fail.

Hello,

there is a "specialty" on this type of touchscreen controller -
the irq pin on the GT9xx series of chips has two distinct
functions:

The first is the regular function for signalling interrupts to
the CPU, which is set up with the "interrupts" property.

The second function comes into play when initializing the chip. 
Without a special initialization procedure, the chip provides
basic touchscreen functionality, but several advanced functions
are unavailable.  To enable those advanced functions, the host
needs to temporarily configure the irq pin as a (host-side)
output and transmit a specific pattern on the reset and irq
lines.  This method doesn't work on all systems, so the driver
only attempts to reprogram the irq line on the host side as an
output if it is explicitly declared with the irq-gpios property.

Regards,
Karsten
-- 
Gem. Par. 28 Abs. 4 Bundesdatenschutzgesetz widerspreche ich der Nutzung
sowie der Weitergabe meiner personenbezogenen Daten für Zwecke der
Werbung sowie der Markt- oder Meinungsforschung.

Re: [PATCH 1/4] ARM: dts: sun7i: Enable touchscreen on Wexler TAB7200 tablet

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 363 bytes --]

On Fri, Dec 18, 2015 at 11:51:50AM +0300, Aleksei Mamlin wrote:
> Add a node for the Goodix GT911 touchscreen found on the Wexler TAB7200 tablet
> 
> Signed-off-by: Aleksei Mamlin <mamlinav-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

Applied, thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[PATCH 1/4] ARM: dts: sun7i: Enable touchscreen on Wexler TAB7200 tablet

[Maxime Ripard]

On Fri, Dec 18, 2015 at 11:51:50AM +0300, Aleksei Mamlin wrote:
> Add a node for the Goodix GT911 touchscreen found on the Wexler TAB7200 tablet
> 
> Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>

Applied, thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20151221/57134f80/attachment.sig>

[PATCH 2/4] ARM: dts: sun7i: Enable PWM controller on Wexler TAB7200 tablet

[Aleksei Mamlin]

Wexler TAB7200 tablet use channel 0 of the PWM controller for backlight dimming

Signed-off-by: Aleksei Mamlin <mamlinav-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
index ec3b837..1dc9079 100644
--- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
+++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
@@ -173,6 +173,12 @@
 	};
 };
 
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pins_a>;
+	status = "okay";
+};
+
 &reg_dcdc2 {
 	regulator-always-on;
 	regulator-min-microvolt = <1000000>;
-- 
2.4.10

[PATCH 2/4] ARM: dts: sun7i: Enable PWM controller on Wexler TAB7200 tablet

[Aleksei Mamlin]

Wexler TAB7200 tablet use channel 0 of the PWM controller for backlight dimming

Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
---
 arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
index ec3b837..1dc9079 100644
--- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
+++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
@@ -173,6 +173,12 @@
 	};
 };
 
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pins_a>;
+	status = "okay";
+};
+
 &reg_dcdc2 {
 	regulator-always-on;
 	regulator-min-microvolt = <1000000>;
-- 
2.4.10

Re: [PATCH 2/4] ARM: dts: sun7i: Enable PWM controller on Wexler TAB7200 tablet

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 365 bytes --]

On Fri, Dec 18, 2015 at 11:52:08AM +0300, Aleksei Mamlin wrote:
> Wexler TAB7200 tablet use channel 0 of the PWM controller for backlight dimming
> 
> Signed-off-by: Aleksei Mamlin <mamlinav-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

Applied, thanks!

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[PATCH 2/4] ARM: dts: sun7i: Enable PWM controller on Wexler TAB7200 tablet

[Maxime Ripard]

On Fri, Dec 18, 2015 at 11:52:08AM +0300, Aleksei Mamlin wrote:
> Wexler TAB7200 tablet use channel 0 of the PWM controller for backlight dimming
> 
> Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>

Applied, thanks!

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20151218/74ae10f1/attachment.sig>

[PATCH 3/4] ARM: dts: sun7i: Add backlight node to Wexler TAB7200 tablet

[Aleksei Mamlin]

Add a backlight for controlling the lcd panel backlight on Wexler TAB7200 tablet

Signed-off-by: Aleksei Mamlin <mamlinav-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
index 1dc9079..f47e5f1 100644
--- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
+++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
@@ -48,6 +48,7 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "Wexler TAB7200";
@@ -57,6 +58,16 @@
 		serial0 = &uart0;
 	};
 
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <8>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bl_enable_pin>;
+		enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
@@ -158,6 +169,13 @@
 };
 
 &pio {
+	bl_enable_pin: bl_enable_pin@0 {
+		allwinner,pins = "PH7";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
 	ts_reset_pin: ts_reset_pin@0 {
 		allwinner,pins = "PB13";
 		allwinner,function = "gpio_out";
-- 
2.4.10

[PATCH 3/4] ARM: dts: sun7i: Add backlight node to Wexler TAB7200 tablet

[Aleksei Mamlin]

Add a backlight for controlling the lcd panel backlight on Wexler TAB7200 tablet

Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
---
 arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
index 1dc9079..f47e5f1 100644
--- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
+++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
@@ -48,6 +48,7 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "Wexler TAB7200";
@@ -57,6 +58,16 @@
 		serial0 = &uart0;
 	};
 
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <8>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bl_enable_pin>;
+		enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
@@ -158,6 +169,13 @@
 };
 
 &pio {
+	bl_enable_pin: bl_enable_pin at 0 {
+		allwinner,pins = "PH7";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
 	ts_reset_pin: ts_reset_pin at 0 {
 		allwinner,pins = "PB13";
 		allwinner,function = "gpio_out";
-- 
2.4.10

Re: [PATCH 3/4] ARM: dts: sun7i: Add backlight node to Wexler TAB7200 tablet

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 438 bytes --]

On Fri, Dec 18, 2015 at 11:52:22AM +0300, Aleksei Mamlin wrote:
> Add a backlight for controlling the lcd panel backlight on Wexler TAB7200 tablet
> 
> Signed-off-by: Aleksei Mamlin <mamlinav-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

This one doesn't apply (probably because of some dependency on the
first patch).

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[PATCH 3/4] ARM: dts: sun7i: Add backlight node to Wexler TAB7200 tablet

[Maxime Ripard]

On Fri, Dec 18, 2015 at 11:52:22AM +0300, Aleksei Mamlin wrote:
> Add a backlight for controlling the lcd panel backlight on Wexler TAB7200 tablet
> 
> Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>

This one doesn't apply (probably because of some dependency on the
first patch).

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20151218/0c2e7a50/attachment.sig>

Re: [PATCH 3/4] ARM: dts: sun7i: Add backlight node to Wexler TAB7200 tablet

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 365 bytes --]

On Fri, Dec 18, 2015 at 11:52:22AM +0300, Aleksei Mamlin wrote:
> Add a backlight for controlling the lcd panel backlight on Wexler TAB7200 tablet
> 
> Signed-off-by: Aleksei Mamlin <mamlinav-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

Applied, thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[PATCH 3/4] ARM: dts: sun7i: Add backlight node to Wexler TAB7200 tablet

[Maxime Ripard]

On Fri, Dec 18, 2015 at 11:52:22AM +0300, Aleksei Mamlin wrote:
> Add a backlight for controlling the lcd panel backlight on Wexler TAB7200 tablet
> 
> Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>

Applied, thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20151221/ee535b3b/attachment.sig>

[PATCH 4/4] ARM: dts: sun7i: Add PA gpio pin to Wexler TAB7200 tablet

[Aleksei Mamlin]

Add PA gpio pin for controlling power of two external amplifiers (NS4890) which are used on the Wexler TAB7200 tablet

Signed-off-by: Aleksei Mamlin <mamlinav-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
index f47e5f1..2f6b21a 100644
--- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
+++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
@@ -74,6 +74,9 @@
 };
 
 &codec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&codec_pa_pin>;
+	allwinner,pa-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
 	status = "okay";
 };
 
@@ -176,6 +179,13 @@
 		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 	};
 
+	codec_pa_pin: codec_pa_pin@0 {
+		allwinner,pins = "PH15";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
 	ts_reset_pin: ts_reset_pin@0 {
 		allwinner,pins = "PB13";
 		allwinner,function = "gpio_out";
-- 
2.4.10

[PATCH 4/4] ARM: dts: sun7i: Add PA gpio pin to Wexler TAB7200 tablet

[Aleksei Mamlin]

Add PA gpio pin for controlling power of two external amplifiers (NS4890) which are used on the Wexler TAB7200 tablet

Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
---
 arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
index f47e5f1..2f6b21a 100644
--- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
+++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
@@ -74,6 +74,9 @@
 };
 
 &codec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&codec_pa_pin>;
+	allwinner,pa-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
 	status = "okay";
 };
 
@@ -176,6 +179,13 @@
 		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 	};
 
+	codec_pa_pin: codec_pa_pin at 0 {
+		allwinner,pins = "PH15";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
 	ts_reset_pin: ts_reset_pin at 0 {
 		allwinner,pins = "PB13";
 		allwinner,function = "gpio_out";
-- 
2.4.10

Re: [PATCH 4/4] ARM: dts: sun7i: Add PA gpio pin to Wexler TAB7200 tablet

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 402 bytes --]

On Fri, Dec 18, 2015 at 11:52:45AM +0300, Aleksei Mamlin wrote:
> Add PA gpio pin for controlling power of two external amplifiers (NS4890) which are used on the Wexler TAB7200 tablet
> 
> Signed-off-by: Aleksei Mamlin <mamlinav-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

Applied, thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[PATCH 4/4] ARM: dts: sun7i: Add PA gpio pin to Wexler TAB7200 tablet

[Maxime Ripard]

On Fri, Dec 18, 2015 at 11:52:45AM +0300, Aleksei Mamlin wrote:
> Add PA gpio pin for controlling power of two external amplifiers (NS4890) which are used on the Wexler TAB7200 tablet
> 
> Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>

Applied, thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20151221/98cbe149/attachment.sig>