[PATCH 00/18] rtl8xxxu: Additional code to support rtl8192eu

[PATCH 00/18] rtl8xxxu: Additional code to support rtl8192eu

[Jes.Sorensen]

From: Jes Sorensen <Jes.Sorensen@redhat.com>

Hi,

Here is another set of patches adding more code to handle the
rtl8192eu. It is relative to wireless-drivers-next as of
2016-04-07. This isn't the complete set to support the 8192eu, I am
breaking it down to make the patch volume easier to manage.

I am hoping we can get it all in so 8192eu support can be enabled in
time for 4.7.

The only contentious issue would be the EXT_PA_8192EU defines, which I
would like to keep in place as it helps me dealing with that later. It
will get cleaned up down the line.

Cheers,
Jes


Jes Sorensen (18):
  rtl8xxxu: Add MAC init table for 8192eu
  rtl8xxxu: Do not mess with AFE_XTAL_CTRL on 8192eu
  rtl8xxxu: Set TX page boundaries for 8192eu
  rtl8xxxu: Add radio init tables for 8192eu
  rtl8xxxu: Add 8192eu AGC tables
  rtl8xxxu: Add 8192eu PHY init table
  rtl8xxxu: Pick PHY init table based on chip version first
  rtl8xxxu: Correctly parse 8192eu efuse
  rtl8xxxu: Handle BB init for 8192eu
  rtl8xxxu: Provide special handling when writing RF regs on 8192eu
  rtl8xxxu: Handle XTAL value setting on 8192eu
  rtl8xxxu: Set correct interrupt masking registers on 8192eu
  rtl8xxxu: Set REG_USB_HRPWM for 8192eu
  rtl8xxxu: Fix LDPC RX hang issue on 8192eu
  rtl8xxxu: Implement 8192eu device specific quirks
  rtl8xxxu: Use proper register name for REG_PAD_CTRL1
  rtl8xxxu: Implement IQK calibration for 8192eu
  rtl8xxxu: Adjust AFE crystal value on 8192eu

 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c   | 1581 +++++++++++++++++---
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h   |   40 +-
 .../net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h  |    7 +
 3 files changed, 1419 insertions(+), 209 deletions(-)

-- 
2.5.5

[PATCH 01/18] rtl8xxxu: Add MAC init table for 8192eu

[Jes.Sorensen]

From: Jes Sorensen <Jes.Sorensen@redhat.com>

The 8192eu requires a different MAC init table. Add the missing table
and specify the table to use in the fileops structure.

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
---
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c | 45 ++++++++++++++++++++----
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h |  1 +
 2 files changed, 40 insertions(+), 6 deletions(-)

diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index 333addd..97e0d17 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -184,6 +184,36 @@ static struct rtl8xxxu_reg8val rtl8723b_mac_init_table[] = {
 	{0xffff, 0xff},
 };
 
+static struct rtl8xxxu_reg8val rtl8192e_mac_init_table[] = {
+	{0x011, 0xeb}, {0x012, 0x07}, {0x014, 0x75}, {0x303, 0xa7},
+	{0x428, 0x0a}, {0x429, 0x10}, {0x430, 0x00}, {0x431, 0x00},
+	{0x432, 0x00}, {0x433, 0x01}, {0x434, 0x04}, {0x435, 0x05},
+	{0x436, 0x07}, {0x437, 0x08}, {0x43c, 0x04}, {0x43d, 0x05},
+	{0x43e, 0x07}, {0x43f, 0x08}, {0x440, 0x5d}, {0x441, 0x01},
+	{0x442, 0x00}, {0x444, 0x10}, {0x445, 0x00}, {0x446, 0x00},
+	{0x447, 0x00}, {0x448, 0x00}, {0x449, 0xf0}, {0x44a, 0x0f},
+	{0x44b, 0x3e}, {0x44c, 0x10}, {0x44d, 0x00}, {0x44e, 0x00},
+	{0x44f, 0x00}, {0x450, 0x00}, {0x451, 0xf0}, {0x452, 0x0f},
+	{0x453, 0x00}, {0x456, 0x5e}, {0x460, 0x66}, {0x461, 0x66},
+	{0x4c8, 0xff}, {0x4c9, 0x08}, {0x4cc, 0xff}, {0x4cd, 0xff},
+	{0x4ce, 0x01}, {0x500, 0x26}, {0x501, 0xa2}, {0x502, 0x2f},
+	{0x503, 0x00}, {0x504, 0x28}, {0x505, 0xa3}, {0x506, 0x5e},
+	{0x507, 0x00}, {0x508, 0x2b}, {0x509, 0xa4}, {0x50a, 0x5e},
+	{0x50b, 0x00}, {0x50c, 0x4f}, {0x50d, 0xa4}, {0x50e, 0x00},
+	{0x50f, 0x00}, {0x512, 0x1c}, {0x514, 0x0a}, {0x516, 0x0a},
+	{0x525, 0x4f}, {0x540, 0x12}, {0x541, 0x64}, {0x550, 0x10},
+	{0x551, 0x10}, {0x559, 0x02}, {0x55c, 0x50}, {0x55d, 0xff},
+	{0x605, 0x30}, {0x608, 0x0e}, {0x609, 0x2a}, {0x620, 0xff},
+	{0x621, 0xff}, {0x622, 0xff}, {0x623, 0xff}, {0x624, 0xff},
+	{0x625, 0xff}, {0x626, 0xff}, {0x627, 0xff}, {0x638, 0x50},
+	{0x63c, 0x0a}, {0x63d, 0x0a}, {0x63e, 0x0e}, {0x63f, 0x0e},
+	{0x640, 0x40}, {0x642, 0x40}, {0x643, 0x00}, {0x652, 0xc8},
+	{0x66e, 0x05}, {0x700, 0x21}, {0x701, 0x43}, {0x702, 0x65},
+	{0x703, 0x87}, {0x708, 0x21}, {0x709, 0x43}, {0x70a, 0x65},
+	{0x70b, 0x87},
+	{0xffff, 0xff},
+};
+
 static struct rtl8xxxu_reg32val rtl8723a_phy_1t_init_table[] = {
 	{0x800, 0x80040000}, {0x804, 0x00000003},
 	{0x808, 0x0000fc00}, {0x80c, 0x0000000a},
@@ -3087,8 +3117,9 @@ static void rtl8723bu_phy_init_antenna_selection(struct rtl8xxxu_priv *priv)
 }
 
 static int
-rtl8xxxu_init_mac(struct rtl8xxxu_priv *priv, struct rtl8xxxu_reg8val *array)
+rtl8xxxu_init_mac(struct rtl8xxxu_priv *priv)
 {
+	struct rtl8xxxu_reg8val *array = priv->fops->mactable;
 	int i, ret;
 	u16 reg;
 	u8 val;
@@ -3103,7 +3134,8 @@ rtl8xxxu_init_mac(struct rtl8xxxu_priv *priv, struct rtl8xxxu_reg8val *array)
 		ret = rtl8xxxu_write8(priv, reg, val);
 		if (ret != 1) {
 			dev_warn(&priv->udev->dev,
-				 "Failed to initialize MAC\n");
+				 "Failed to initialize MAC "
+				 "(reg: %04x, val %02x)\n", reg, val);
 			return -EAGAIN;
 		}
 	}
@@ -6369,10 +6401,7 @@ static int rtl8xxxu_init_device(struct ieee80211_hw *hw)
 	if (priv->fops->phy_init_antenna_selection)
 		priv->fops->phy_init_antenna_selection(priv);
 
-	if (priv->rtl_chip == RTL8723B)
-		ret = rtl8xxxu_init_mac(priv, rtl8723b_mac_init_table);
-	else
-		ret = rtl8xxxu_init_mac(priv, rtl8723a_mac_init_table);
+	ret = rtl8xxxu_init_mac(priv);
 
 	dev_dbg(dev, "%s: init_mac %i\n", __func__, ret);
 	if (ret)
@@ -8452,6 +8481,7 @@ static struct rtl8xxxu_fileops rtl8723au_fops = {
 	.adda_1t_path_on = 0x0bdb25a0,
 	.adda_2t_path_on_a = 0x04db25a4,
 	.adda_2t_path_on_b = 0x0b1b25a4,
+	.mactable = rtl8723a_mac_init_table,
 };
 
 static struct rtl8xxxu_fileops rtl8723bu_fops = {
@@ -8481,6 +8511,7 @@ static struct rtl8xxxu_fileops rtl8723bu_fops = {
 	.adda_1t_path_on = 0x01c00014,
 	.adda_2t_path_on_a = 0x01c00014,
 	.adda_2t_path_on_b = 0x01c00014,
+	.mactable = rtl8723b_mac_init_table,
 };
 
 #ifdef CONFIG_RTL8XXXU_UNTESTED
@@ -8508,6 +8539,7 @@ static struct rtl8xxxu_fileops rtl8192cu_fops = {
 	.adda_1t_path_on = 0x0bdb25a0,
 	.adda_2t_path_on_a = 0x04db25a4,
 	.adda_2t_path_on_b = 0x0b1b25a4,
+	.mactable = rtl8723a_mac_init_table,
 };
 
 #endif
@@ -8536,6 +8568,7 @@ static struct rtl8xxxu_fileops rtl8192eu_fops = {
 	.adda_1t_path_on = 0x0fc01616,
 	.adda_2t_path_on_a = 0x0fc01616,
 	.adda_2t_path_on_b = 0x0fc01616,
+	.mactable = rtl8192e_mac_init_table,
 };
 
 static struct usb_device_id dev_table[] = {
diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h
index 455e112..94fc217 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h
@@ -1308,4 +1308,5 @@ struct rtl8xxxu_fileops {
 	u32 adda_1t_path_on;
 	u32 adda_2t_path_on_a;
 	u32 adda_2t_path_on_b;
+	struct rtl8xxxu_reg8val *mactable;
 };
-- 
2.5.5

[PATCH 02/18] rtl8xxxu: Do not mess with AFE_XTAL_CTRL on 8192eu

[Jes.Sorensen]

From: Jes Sorensen <Jes.Sorensen@redhat.com>

To match the vendor driver, do not mess with AFE_XTAL_CTRL on 8192eu.

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
---
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index 97e0d17..a4662a0 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -3208,7 +3208,7 @@ static int rtl8xxxu_init_phy_bb(struct rtl8xxxu_priv *priv)
 		rtl8xxxu_write16(priv, REG_SYS_FUNC, val16);
 	}
 
-	if (priv->rtl_chip != RTL8723B) {
+	if (priv->rtl_chip != RTL8723B && priv->rtl_chip != RTL8192E) {
 		/* AFE_XTAL_RF_GATE (bit 14) if addressing as 32 bit register */
 		val32 = rtl8xxxu_read32(priv, REG_AFE_XTAL_CTRL);
 		val32 &= ~AFE_XTAL_RF_GATE;
-- 
2.5.5

[PATCH 03/18] rtl8xxxu: Set TX page boundaries for 8192eu

[Jes.Sorensen]

From: Jes Sorensen <Jes.Sorensen@redhat.com>

The 8192eu also has it's own TRXFF boundary value to set.

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
---
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c | 7 ++++++-
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h | 1 +
 2 files changed, 7 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index a4662a0..13e8d60 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -6495,7 +6495,10 @@ static int rtl8xxxu_init_device(struct ieee80211_hw *hw)
 		/*
 		 * Set TX buffer boundary
 		 */
-		val8 = TX_TOTAL_PAGE_NUM + 1;
+		if (priv->rtl_chip == RTL8192E)
+			val8 = TX_TOTAL_PAGE_NUM_8192E + 1;
+		else
+			val8 = TX_TOTAL_PAGE_NUM + 1;
 
 		if (priv->rtl_chip == RTL8723B)
 			val8 -= 1;
@@ -6532,6 +6535,8 @@ static int rtl8xxxu_init_device(struct ieee80211_hw *hw)
 	 */
 	if (priv->rtl_chip == RTL8723B)
 		rtl8xxxu_write16(priv, REG_TRXFF_BNDY + 2, 0x3f7f);
+	else if (priv->rtl_chip == RTL8192E)
+		rtl8xxxu_write16(priv, REG_TRXFF_BNDY + 2, 0x3cff);
 	else
 		rtl8xxxu_write16(priv, REG_TRXFF_BNDY + 2, 0x27ff);
 	/*
diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h
index 94fc217..63d7268 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h
@@ -42,6 +42,7 @@
 #define REALTEK_USB_CMD_IDX		0x00
 
 #define TX_TOTAL_PAGE_NUM		0xf8
+#define TX_TOTAL_PAGE_NUM_8192E		0xf3
 /* (HPQ + LPQ + NPQ + PUBQ) = TX_TOTAL_PAGE_NUM */
 #define TX_PAGE_NUM_PUBQ		0xe7
 #define TX_PAGE_NUM_HI_PQ		0x0c
-- 
2.5.5

[PATCH 04/18] rtl8xxxu: Add radio init tables for 8192eu

[Jes.Sorensen]

From: Jes Sorensen <Jes.Sorensen@redhat.com>

Add the required radio init tables for 8192eu devices.

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
---
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c | 154 +++++++++++++++++++++++
 1 file changed, 154 insertions(+)

diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index 13e8d60..988aba6 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -1242,6 +1242,152 @@ static struct rtl8xxxu_rfregval rtl8188ru_radioa_1t_highpa_table[] = {
 	{0xff, 0xffffffff}
 };
 
+static struct rtl8xxxu_rfregval rtl8192eu_radioa_init_table[] = {
+	{0x7f, 0x00000082}, {0x81, 0x0003fc00},
+	{0x00, 0x00030000}, {0x08, 0x00008400},
+	{0x18, 0x00000407}, {0x19, 0x00000012},
+	{0x1b, 0x00000064}, {0x1e, 0x00080009},
+	{0x1f, 0x00000880}, {0x2f, 0x0001a060},
+	{0x3f, 0x00000000}, {0x42, 0x000060c0},
+	{0x57, 0x000d0000}, {0x58, 0x000be180},
+	{0x67, 0x00001552}, {0x83, 0x00000000},
+	{0xb0, 0x000ff9f1}, {0xb1, 0x00055418},
+	{0xb2, 0x0008cc00}, {0xb4, 0x00043083},
+	{0xb5, 0x00008166}, {0xb6, 0x0000803e},
+	{0xb7, 0x0001c69f}, {0xb8, 0x0000407f},
+	{0xb9, 0x00080001}, {0xba, 0x00040001},
+	{0xbb, 0x00000400}, {0xbf, 0x000c0000},
+	{0xc2, 0x00002400}, {0xc3, 0x00000009},
+	{0xc4, 0x00040c91}, {0xc5, 0x00099999},
+	{0xc6, 0x000000a3}, {0xc7, 0x00088820},
+	{0xc8, 0x00076c06}, {0xc9, 0x00000000},
+	{0xca, 0x00080000}, {0xdf, 0x00000180},
+	{0xef, 0x000001a0}, {0x51, 0x00069545},
+	{0x52, 0x0007e45e}, {0x53, 0x00000071},
+	{0x56, 0x00051ff3}, {0x35, 0x000000a8},
+	{0x35, 0x000001e2}, {0x35, 0x000002a8},
+	{0x36, 0x00001c24}, {0x36, 0x00009c24},
+	{0x36, 0x00011c24}, {0x36, 0x00019c24},
+	{0x18, 0x00000c07}, {0x5a, 0x00048000},
+	{0x19, 0x000739d0},
+#ifdef EXT_PA_8192EU
+	/* External PA or external LNA */
+	{0x34, 0x0000a093}, {0x34, 0x0000908f},
+	{0x34, 0x0000808c}, {0x34, 0x0000704d},
+	{0x34, 0x0000604a}, {0x34, 0x00005047},
+	{0x34, 0x0000400a}, {0x34, 0x00003007},
+	{0x34, 0x00002004}, {0x34, 0x00001001},
+	{0x34, 0x00000000},
+#else
+	/* Regular */
+	{0x34, 0x0000add7}, {0x34, 0x00009dd4},
+	{0x34, 0x00008dd1}, {0x34, 0x00007dce},
+	{0x34, 0x00006dcb}, {0x34, 0x00005dc8},
+	{0x34, 0x00004dc5}, {0x34, 0x000034cc},
+	{0x34, 0x0000244f}, {0x34, 0x0000144c},
+	{0x34, 0x00000014},
+#endif
+	{0x00, 0x00030159},
+	{0x84, 0x00068180},
+	{0x86, 0x0000014e},
+	{0x87, 0x00048e00},
+	{0x8e, 0x00065540},
+	{0x8f, 0x00088000},
+	{0xef, 0x000020a0},
+#ifdef EXT_PA_8192EU
+	/* External PA or external LNA */
+	{0x3b, 0x000f07b0},
+#else
+	{0x3b, 0x000f02b0},
+#endif
+	{0x3b, 0x000ef7b0}, {0x3b, 0x000d4fb0},
+	{0x3b, 0x000cf060}, {0x3b, 0x000b0090},
+	{0x3b, 0x000a0080}, {0x3b, 0x00090080},
+	{0x3b, 0x0008f780},
+#ifdef EXT_PA_8192EU
+	/* External PA or external LNA */
+	{0x3b, 0x000787b0},
+#else
+	{0x3b, 0x00078730},
+#endif
+	{0x3b, 0x00060fb0}, {0x3b, 0x0005ffa0},
+	{0x3b, 0x00040620}, {0x3b, 0x00037090},
+	{0x3b, 0x00020080}, {0x3b, 0x0001f060},
+	{0x3b, 0x0000ffb0}, {0xef, 0x000000a0},
+	{0xfe, 0x00000000}, {0x18, 0x0000fc07},
+	{0xfe, 0x00000000}, {0xfe, 0x00000000},
+	{0xfe, 0x00000000}, {0xfe, 0x00000000},
+	{0x1e, 0x00000001}, {0x1f, 0x00080000},
+	{0x00, 0x00033e70},
+	{0xff, 0xffffffff}
+};
+
+static struct rtl8xxxu_rfregval rtl8192eu_radiob_init_table[] = {
+	{0x7f, 0x00000082}, {0x81, 0x0003fc00},
+	{0x00, 0x00030000}, {0x08, 0x00008400},
+	{0x18, 0x00000407}, {0x19, 0x00000012},
+	{0x1b, 0x00000064}, {0x1e, 0x00080009},
+	{0x1f, 0x00000880}, {0x2f, 0x0001a060},
+	{0x3f, 0x00000000}, {0x42, 0x000060c0},
+	{0x57, 0x000d0000}, {0x58, 0x000be180},
+	{0x67, 0x00001552}, {0x7f, 0x00000082},
+	{0x81, 0x0003f000}, {0x83, 0x00000000},
+	{0xdf, 0x00000180}, {0xef, 0x000001a0},
+	{0x51, 0x00069545}, {0x52, 0x0007e42e},
+	{0x53, 0x00000071}, {0x56, 0x00051ff3},
+	{0x35, 0x000000a8}, {0x35, 0x000001e0},
+	{0x35, 0x000002a8}, {0x36, 0x00001ca8},
+	{0x36, 0x00009c24}, {0x36, 0x00011c24},
+	{0x36, 0x00019c24}, {0x18, 0x00000c07},
+	{0x5a, 0x00048000}, {0x19, 0x000739d0},
+#ifdef EXT_PA_8192EU
+	/* External PA or external LNA */
+	{0x34, 0x0000a093}, {0x34, 0x0000908f},
+	{0x34, 0x0000808c}, {0x34, 0x0000704d},
+	{0x34, 0x0000604a}, {0x34, 0x00005047},
+	{0x34, 0x0000400a}, {0x34, 0x00003007},
+	{0x34, 0x00002004}, {0x34, 0x00001001},
+	{0x34, 0x00000000},
+#else
+	{0x34, 0x0000add7}, {0x34, 0x00009dd4},
+	{0x34, 0x00008dd1}, {0x34, 0x00007dce},
+	{0x34, 0x00006dcb}, {0x34, 0x00005dc8},
+	{0x34, 0x00004dc5}, {0x34, 0x000034cc},
+	{0x34, 0x0000244f}, {0x34, 0x0000144c},
+	{0x34, 0x00000014},
+#endif
+	{0x00, 0x00030159}, {0x84, 0x00068180},
+	{0x86, 0x000000ce}, {0x87, 0x00048a00},
+	{0x8e, 0x00065540}, {0x8f, 0x00088000},
+	{0xef, 0x000020a0},
+#ifdef EXT_PA_8192EU
+	/* External PA or external LNA */
+	{0x3b, 0x000f07b0},
+#else
+	{0x3b, 0x000f02b0},
+#endif
+
+	{0x3b, 0x000ef7b0}, {0x3b, 0x000d4fb0},
+	{0x3b, 0x000cf060}, {0x3b, 0x000b0090},
+	{0x3b, 0x000a0080}, {0x3b, 0x00090080},
+	{0x3b, 0x0008f780},
+#ifdef EXT_PA_8192EU
+	/* External PA or external LNA */
+	{0x3b, 0x000787b0},
+#else
+	{0x3b, 0x00078730},
+#endif
+	{0x3b, 0x00060fb0}, {0x3b, 0x0005ffa0},
+	{0x3b, 0x00040620}, {0x3b, 0x00037090},
+	{0x3b, 0x00020080}, {0x3b, 0x0001f060},
+	{0x3b, 0x0000ffb0}, {0xef, 0x000000a0},
+	{0x00, 0x00010159}, {0xfe, 0x00000000},
+	{0xfe, 0x00000000}, {0xfe, 0x00000000},
+	{0xfe, 0x00000000}, {0x1e, 0x00000001},
+	{0x1f, 0x00080000}, {0x00, 0x00033e70},
+	{0xff, 0xffffffff}
+};
+
 static struct rtl8xxxu_rfregs rtl8xxxu_rfregs[] = {
 	{	/* RF_A */
 		.hssiparm1 = REG_FPGA0_XA_HSSI_PARM1,
@@ -6447,6 +6593,14 @@ static int rtl8xxxu_init_device(struct ieee80211_hw *hw)
 		rftable = rtl8192cu_radiob_2t_init_table;
 		ret = rtl8xxxu_init_phy_rf(priv, rftable, RF_B);
 		break;
+	case RTL8192E:
+		rftable = rtl8192eu_radioa_init_table;
+		ret = rtl8xxxu_init_phy_rf(priv, rftable, RF_A);
+		if (ret)
+			break;
+		rftable = rtl8192eu_radiob_init_table;
+		ret = rtl8xxxu_init_phy_rf(priv, rftable, RF_B);
+		break;
 	default:
 		ret = -EINVAL;
 	}
-- 
2.5.5

[PATCH 05/18] rtl8xxxu: Add 8192eu AGC tables

[Jes.Sorensen]

From: Jes Sorensen <Jes.Sorensen@redhat.com>

A device specific AGC table is required for the 8192eu as well.

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
---
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c | 147 ++++++++++++++++++++++-
 1 file changed, 146 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index 988aba6..c12cb63 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -849,6 +849,144 @@ static struct rtl8xxxu_reg32val rtl8xxx_agc_8723bu_table[] = {
 	{0xffff, 0xffffffff}
 };
 
+static struct rtl8xxxu_reg32val rtl8xxx_agc_8192eu_std_table[] = {
+	{0xc78, 0xfb000001}, {0xc78, 0xfb010001},
+	{0xc78, 0xfb020001}, {0xc78, 0xfb030001},
+	{0xc78, 0xfb040001}, {0xc78, 0xfb050001},
+	{0xc78, 0xfa060001}, {0xc78, 0xf9070001},
+	{0xc78, 0xf8080001}, {0xc78, 0xf7090001},
+	{0xc78, 0xf60a0001}, {0xc78, 0xf50b0001},
+	{0xc78, 0xf40c0001}, {0xc78, 0xf30d0001},
+	{0xc78, 0xf20e0001}, {0xc78, 0xf10f0001},
+	{0xc78, 0xf0100001}, {0xc78, 0xef110001},
+	{0xc78, 0xee120001}, {0xc78, 0xed130001},
+	{0xc78, 0xec140001}, {0xc78, 0xeb150001},
+	{0xc78, 0xea160001}, {0xc78, 0xe9170001},
+	{0xc78, 0xe8180001}, {0xc78, 0xe7190001},
+	{0xc78, 0xc81a0001}, {0xc78, 0xc71b0001},
+	{0xc78, 0xc61c0001}, {0xc78, 0x071d0001},
+	{0xc78, 0x061e0001}, {0xc78, 0x051f0001},
+	{0xc78, 0x04200001}, {0xc78, 0x03210001},
+	{0xc78, 0xaa220001}, {0xc78, 0xa9230001},
+	{0xc78, 0xa8240001}, {0xc78, 0xa7250001},
+	{0xc78, 0xa6260001}, {0xc78, 0x85270001},
+	{0xc78, 0x84280001}, {0xc78, 0x83290001},
+	{0xc78, 0x252a0001}, {0xc78, 0x242b0001},
+	{0xc78, 0x232c0001}, {0xc78, 0x222d0001},
+	{0xc78, 0x672e0001}, {0xc78, 0x662f0001},
+	{0xc78, 0x65300001}, {0xc78, 0x64310001},
+	{0xc78, 0x63320001}, {0xc78, 0x62330001},
+	{0xc78, 0x61340001}, {0xc78, 0x45350001},
+	{0xc78, 0x44360001}, {0xc78, 0x43370001},
+	{0xc78, 0x42380001}, {0xc78, 0x41390001},
+	{0xc78, 0x403a0001}, {0xc78, 0x403b0001},
+	{0xc78, 0x403c0001}, {0xc78, 0x403d0001},
+	{0xc78, 0x403e0001}, {0xc78, 0x403f0001},
+	{0xc78, 0xfb400001}, {0xc78, 0xfb410001},
+	{0xc78, 0xfb420001}, {0xc78, 0xfb430001},
+	{0xc78, 0xfb440001}, {0xc78, 0xfb450001},
+	{0xc78, 0xfa460001}, {0xc78, 0xf9470001},
+	{0xc78, 0xf8480001}, {0xc78, 0xf7490001},
+	{0xc78, 0xf64a0001}, {0xc78, 0xf54b0001},
+	{0xc78, 0xf44c0001}, {0xc78, 0xf34d0001},
+	{0xc78, 0xf24e0001}, {0xc78, 0xf14f0001},
+	{0xc78, 0xf0500001}, {0xc78, 0xef510001},
+	{0xc78, 0xee520001}, {0xc78, 0xed530001},
+	{0xc78, 0xec540001}, {0xc78, 0xeb550001},
+	{0xc78, 0xea560001}, {0xc78, 0xe9570001},
+	{0xc78, 0xe8580001}, {0xc78, 0xe7590001},
+	{0xc78, 0xe65a0001}, {0xc78, 0xe55b0001},
+	{0xc78, 0xe45c0001}, {0xc78, 0xe35d0001},
+	{0xc78, 0xe25e0001}, {0xc78, 0xe15f0001},
+	{0xc78, 0x8a600001}, {0xc78, 0x89610001},
+	{0xc78, 0x88620001}, {0xc78, 0x87630001},
+	{0xc78, 0x86640001}, {0xc78, 0x85650001},
+	{0xc78, 0x84660001}, {0xc78, 0x83670001},
+	{0xc78, 0x82680001}, {0xc78, 0x6b690001},
+	{0xc78, 0x6a6a0001}, {0xc78, 0x696b0001},
+	{0xc78, 0x686c0001}, {0xc78, 0x676d0001},
+	{0xc78, 0x666e0001}, {0xc78, 0x656f0001},
+	{0xc78, 0x64700001}, {0xc78, 0x63710001},
+	{0xc78, 0x62720001}, {0xc78, 0x61730001},
+	{0xc78, 0x49740001}, {0xc78, 0x48750001},
+	{0xc78, 0x47760001}, {0xc78, 0x46770001},
+	{0xc78, 0x45780001}, {0xc78, 0x44790001},
+	{0xc78, 0x437a0001}, {0xc78, 0x427b0001},
+	{0xc78, 0x417c0001}, {0xc78, 0x407d0001},
+	{0xc78, 0x407e0001}, {0xc78, 0x407f0001},
+	{0xc50, 0x00040022}, {0xc50, 0x00040020},
+	{0xffff, 0xffffffff}
+};
+
+static struct rtl8xxxu_reg32val rtl8xxx_agc_8192eu_highpa_table[] = {
+	{0xc78, 0xfa000001}, {0xc78, 0xf9010001},
+	{0xc78, 0xf8020001}, {0xc78, 0xf7030001},
+	{0xc78, 0xf6040001}, {0xc78, 0xf5050001},
+	{0xc78, 0xf4060001}, {0xc78, 0xf3070001},
+	{0xc78, 0xf2080001}, {0xc78, 0xf1090001},
+	{0xc78, 0xf00a0001}, {0xc78, 0xef0b0001},
+	{0xc78, 0xee0c0001}, {0xc78, 0xed0d0001},
+	{0xc78, 0xec0e0001}, {0xc78, 0xeb0f0001},
+	{0xc78, 0xea100001}, {0xc78, 0xe9110001},
+	{0xc78, 0xe8120001}, {0xc78, 0xe7130001},
+	{0xc78, 0xe6140001}, {0xc78, 0xe5150001},
+	{0xc78, 0xe4160001}, {0xc78, 0xe3170001},
+	{0xc78, 0xe2180001}, {0xc78, 0xe1190001},
+	{0xc78, 0x8a1a0001}, {0xc78, 0x891b0001},
+	{0xc78, 0x881c0001}, {0xc78, 0x871d0001},
+	{0xc78, 0x861e0001}, {0xc78, 0x851f0001},
+	{0xc78, 0x84200001}, {0xc78, 0x83210001},
+	{0xc78, 0x82220001}, {0xc78, 0x6a230001},
+	{0xc78, 0x69240001}, {0xc78, 0x68250001},
+	{0xc78, 0x67260001}, {0xc78, 0x66270001},
+	{0xc78, 0x65280001}, {0xc78, 0x64290001},
+	{0xc78, 0x632a0001}, {0xc78, 0x622b0001},
+	{0xc78, 0x612c0001}, {0xc78, 0x602d0001},
+	{0xc78, 0x472e0001}, {0xc78, 0x462f0001},
+	{0xc78, 0x45300001}, {0xc78, 0x44310001},
+	{0xc78, 0x43320001}, {0xc78, 0x42330001},
+	{0xc78, 0x41340001}, {0xc78, 0x40350001},
+	{0xc78, 0x40360001}, {0xc78, 0x40370001},
+	{0xc78, 0x40380001}, {0xc78, 0x40390001},
+	{0xc78, 0x403a0001}, {0xc78, 0x403b0001},
+	{0xc78, 0x403c0001}, {0xc78, 0x403d0001},
+	{0xc78, 0x403e0001}, {0xc78, 0x403f0001},
+	{0xc78, 0xfa400001}, {0xc78, 0xf9410001},
+	{0xc78, 0xf8420001}, {0xc78, 0xf7430001},
+	{0xc78, 0xf6440001}, {0xc78, 0xf5450001},
+	{0xc78, 0xf4460001}, {0xc78, 0xf3470001},
+	{0xc78, 0xf2480001}, {0xc78, 0xf1490001},
+	{0xc78, 0xf04a0001}, {0xc78, 0xef4b0001},
+	{0xc78, 0xee4c0001}, {0xc78, 0xed4d0001},
+	{0xc78, 0xec4e0001}, {0xc78, 0xeb4f0001},
+	{0xc78, 0xea500001}, {0xc78, 0xe9510001},
+	{0xc78, 0xe8520001}, {0xc78, 0xe7530001},
+	{0xc78, 0xe6540001}, {0xc78, 0xe5550001},
+	{0xc78, 0xe4560001}, {0xc78, 0xe3570001},
+	{0xc78, 0xe2580001}, {0xc78, 0xe1590001},
+	{0xc78, 0x8a5a0001}, {0xc78, 0x895b0001},
+	{0xc78, 0x885c0001}, {0xc78, 0x875d0001},
+	{0xc78, 0x865e0001}, {0xc78, 0x855f0001},
+	{0xc78, 0x84600001}, {0xc78, 0x83610001},
+	{0xc78, 0x82620001}, {0xc78, 0x6a630001},
+	{0xc78, 0x69640001}, {0xc78, 0x68650001},
+	{0xc78, 0x67660001}, {0xc78, 0x66670001},
+	{0xc78, 0x65680001}, {0xc78, 0x64690001},
+	{0xc78, 0x636a0001}, {0xc78, 0x626b0001},
+	{0xc78, 0x616c0001}, {0xc78, 0x606d0001},
+	{0xc78, 0x476e0001}, {0xc78, 0x466f0001},
+	{0xc78, 0x45700001}, {0xc78, 0x44710001},
+	{0xc78, 0x43720001}, {0xc78, 0x42730001},
+	{0xc78, 0x41740001}, {0xc78, 0x40750001},
+	{0xc78, 0x40760001}, {0xc78, 0x40770001},
+	{0xc78, 0x40780001}, {0xc78, 0x40790001},
+	{0xc78, 0x407a0001}, {0xc78, 0x407b0001},
+	{0xc78, 0x407c0001}, {0xc78, 0x407d0001},
+	{0xc78, 0x407e0001}, {0xc78, 0x407f0001},
+	{0xc50, 0x00040222}, {0xc50, 0x00040220},
+	{0xffff, 0xffffffff}
+};
+
 static struct rtl8xxxu_rfregval rtl8723au_radioa_1t_init_table[] = {
 	{0x00, 0x00030159}, {0x01, 0x00031284},
 	{0x02, 0x00098000}, {0x03, 0x00039c63},
@@ -3446,7 +3584,14 @@ static int rtl8xxxu_init_phy_bb(struct rtl8xxxu_priv *priv)
 
 	if (priv->rtl_chip == RTL8723B)
 		rtl8xxxu_init_phy_regs(priv, rtl8xxx_agc_8723bu_table);
-	else if (priv->hi_pa)
+	else if (priv->rtl_chip == RTL8192E) {
+		if (priv->hi_pa)
+			rtl8xxxu_init_phy_regs(priv,
+					       rtl8xxx_agc_8192eu_highpa_table);
+		else
+			rtl8xxxu_init_phy_regs(priv,
+					       rtl8xxx_agc_8192eu_std_table);
+	} else if (priv->hi_pa)
 		rtl8xxxu_init_phy_regs(priv, rtl8xxx_agc_highpa_table);
 	else
 		rtl8xxxu_init_phy_regs(priv, rtl8xxx_agc_standard_table);
-- 
2.5.5

[PATCH 06/18] rtl8xxxu: Add 8192eu PHY init table

[Jes.Sorensen]

From: Jes Sorensen <Jes.Sorensen@redhat.com>

The 8192eu also requires it's own PHY init table.

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
---
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c | 140 +++++++++++++++++++++++
 1 file changed, 140 insertions(+)

diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index c12cb63..fa6ab85 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -610,6 +610,138 @@ static struct rtl8xxxu_reg32val rtl8188ru_phy_1t_highpa_table[] = {
 	{0xffff, 0xffffffff},
 };
 
+static struct rtl8xxxu_reg32val rtl8192eu_phy_init_table[] = {
+	{0x800, 0x80040000}, {0x804, 0x00000003},
+	{0x808, 0x0000fc00}, {0x80c, 0x0000000a},
+	{0x810, 0x10001331}, {0x814, 0x020c3d10},
+	{0x818, 0x02220385}, {0x81c, 0x00000000},
+	{0x820, 0x01000100}, {0x824, 0x00390204},
+	{0x828, 0x01000100}, {0x82c, 0x00390204},
+	{0x830, 0x32323232}, {0x834, 0x30303030},
+	{0x838, 0x30303030}, {0x83c, 0x30303030},
+	{0x840, 0x00010000}, {0x844, 0x00010000},
+	{0x848, 0x28282828}, {0x84c, 0x28282828},
+	{0x850, 0x00000000}, {0x854, 0x00000000},
+	{0x858, 0x009a009a}, {0x85c, 0x01000014},
+	{0x860, 0x66f60000}, {0x864, 0x061f0000},
+	{0x868, 0x30303030}, {0x86c, 0x30303030},
+	{0x870, 0x00000000}, {0x874, 0x55004200},
+	{0x878, 0x08080808}, {0x87c, 0x00000000},
+	{0x880, 0xb0000c1c}, {0x884, 0x00000001},
+	{0x888, 0x00000000}, {0x88c, 0xcc0000c0},
+	{0x890, 0x00000800}, {0x894, 0xfffffffe},
+	{0x898, 0x40302010}, {0x900, 0x00000000},
+	{0x904, 0x00000023}, {0x908, 0x00000000},
+	{0x90c, 0x81121313}, {0x910, 0x806c0001},
+	{0x914, 0x00000001}, {0x918, 0x00000000},
+	{0x91c, 0x00010000}, {0x924, 0x00000001},
+	{0x928, 0x00000000}, {0x92c, 0x00000000},
+	{0x930, 0x00000000}, {0x934, 0x00000000},
+	{0x938, 0x00000000}, {0x93c, 0x00000000},
+	{0x940, 0x00000000}, {0x944, 0x00000000},
+	{0x94c, 0x00000008}, {0xa00, 0x00d0c7c8},
+	{0xa04, 0x81ff000c}, {0xa08, 0x8c838300},
+	{0xa0c, 0x2e68120f}, {0xa10, 0x95009b78},
+	{0xa14, 0x1114d028}, {0xa18, 0x00881117},
+	{0xa1c, 0x89140f00}, {0xa20, 0x1a1b0000},
+	{0xa24, 0x090e1317}, {0xa28, 0x00000204},
+	{0xa2c, 0x00d30000}, {0xa70, 0x101fff00},
+	{0xa74, 0x00000007}, {0xa78, 0x00000900},
+	{0xa7c, 0x225b0606}, {0xa80, 0x218075b1},
+	{0xb38, 0x00000000}, {0xc00, 0x48071d40},
+	{0xc04, 0x03a05633}, {0xc08, 0x000000e4},
+	{0xc0c, 0x6c6c6c6c}, {0xc10, 0x08800000},
+	{0xc14, 0x40000100}, {0xc18, 0x08800000},
+	{0xc1c, 0x40000100}, {0xc20, 0x00000000},
+	{0xc24, 0x00000000}, {0xc28, 0x00000000},
+	{0xc2c, 0x00000000}, {0xc30, 0x69e9ac47},
+	{0xc34, 0x469652af}, {0xc38, 0x49795994},
+	{0xc3c, 0x0a97971c}, {0xc40, 0x1f7c403f},
+	{0xc44, 0x000100b7}, {0xc48, 0xec020107},
+	{0xc4c, 0x007f037f},
+#ifdef EXT_PA_8192EU
+	/* External PA or external LNA */
+	{0xc50, 0x00340220},
+#else
+	{0xc50, 0x00340020},
+#endif
+	{0xc54, 0x0080801f},
+#ifdef EXT_PA_8192EU
+	/* External PA or external LNA */
+	{0xc58, 0x00000220},
+#else
+	{0xc58, 0x00000020},
+#endif
+	{0xc5c, 0x00248492}, {0xc60, 0x00000000},
+	{0xc64, 0x7112848b}, {0xc68, 0x47c00bff},
+	{0xc6c, 0x00000036}, {0xc70, 0x00000600},
+	{0xc74, 0x02013169}, {0xc78, 0x0000001f},
+	{0xc7c, 0x00b91612},
+#ifdef EXT_PA_8192EU
+	/* External PA or external LNA */
+	{0xc80, 0x2d4000b5},
+#else
+	{0xc80, 0x40000100},
+#endif
+	{0xc84, 0x21f60000},
+#ifdef EXT_PA_8192EU
+	/* External PA or external LNA */
+	{0xc88, 0x2d4000b5},
+#else
+	{0xc88, 0x40000100},
+#endif
+	{0xc8c, 0xa0e40000}, {0xc90, 0x00121820},
+	{0xc94, 0x00000000}, {0xc98, 0x00121820},
+	{0xc9c, 0x00007f7f}, {0xca0, 0x00000000},
+	{0xca4, 0x000300a0}, {0xca8, 0x00000000},
+	{0xcac, 0x00000000}, {0xcb0, 0x00000000},
+	{0xcb4, 0x00000000}, {0xcb8, 0x00000000},
+	{0xcbc, 0x28000000}, {0xcc0, 0x00000000},
+	{0xcc4, 0x00000000}, {0xcc8, 0x00000000},
+	{0xccc, 0x00000000}, {0xcd0, 0x00000000},
+	{0xcd4, 0x00000000}, {0xcd8, 0x64b22427},
+	{0xcdc, 0x00766932}, {0xce0, 0x00222222},
+	{0xce4, 0x00040000}, {0xce8, 0x77644302},
+	{0xcec, 0x2f97d40c}, {0xd00, 0x00080740},
+	{0xd04, 0x00020403}, {0xd08, 0x0000907f},
+	{0xd0c, 0x20010201}, {0xd10, 0xa0633333},
+	{0xd14, 0x3333bc43}, {0xd18, 0x7a8f5b6b},
+	{0xd1c, 0x0000007f}, {0xd2c, 0xcc979975},
+	{0xd30, 0x00000000}, {0xd34, 0x80608000},
+	{0xd38, 0x00000000}, {0xd3c, 0x00127353},
+	{0xd40, 0x00000000}, {0xd44, 0x00000000},
+	{0xd48, 0x00000000}, {0xd4c, 0x00000000},
+	{0xd50, 0x6437140a}, {0xd54, 0x00000000},
+	{0xd58, 0x00000282}, {0xd5c, 0x30032064},
+	{0xd60, 0x4653de68}, {0xd64, 0x04518a3c},
+	{0xd68, 0x00002101}, {0xd6c, 0x2a201c16},
+	{0xd70, 0x1812362e}, {0xd74, 0x322c2220},
+	{0xd78, 0x000e3c24}, {0xd80, 0x01081008},
+	{0xd84, 0x00000800}, {0xd88, 0xf0b50000},
+	{0xe00, 0x30303030}, {0xe04, 0x30303030},
+	{0xe08, 0x03903030}, {0xe10, 0x30303030},
+	{0xe14, 0x30303030}, {0xe18, 0x30303030},
+	{0xe1c, 0x30303030}, {0xe28, 0x00000000},
+	{0xe30, 0x1000dc1f}, {0xe34, 0x10008c1f},
+	{0xe38, 0x02140102}, {0xe3c, 0x681604c2},
+	{0xe40, 0x01007c00}, {0xe44, 0x01004800},
+	{0xe48, 0xfb000000}, {0xe4c, 0x000028d1},
+	{0xe50, 0x1000dc1f}, {0xe54, 0x10008c1f},
+	{0xe58, 0x02140102}, {0xe5c, 0x28160d05},
+	{0xe60, 0x00000008}, {0xe68, 0x0fc05656},
+	{0xe6c, 0x03c09696}, {0xe70, 0x03c09696},
+	{0xe74, 0x0c005656}, {0xe78, 0x0c005656},
+	{0xe7c, 0x0c005656}, {0xe80, 0x0c005656},
+	{0xe84, 0x03c09696}, {0xe88, 0x0c005656},
+	{0xe8c, 0x03c09696}, {0xed0, 0x03c09696},
+	{0xed4, 0x03c09696}, {0xed8, 0x03c09696},
+	{0xedc, 0x0000d6d6}, {0xee0, 0x0000d6d6},
+	{0xeec, 0x0fc01616}, {0xee4, 0xb0000c1c},
+	{0xee8, 0x00000001}, {0xf14, 0x00000003},
+	{0xf4c, 0x00000000}, {0xf00, 0x00000300},
+	{0xffff, 0xffffffff},
+};
+
 static struct rtl8xxxu_reg32val rtl8xxx_agc_standard_table[] = {
 	{0xc78, 0x7b000001}, {0xc78, 0x7b010001},
 	{0xc78, 0x7b020001}, {0xc78, 0x7b030001},
@@ -3516,6 +3648,14 @@ static int rtl8xxxu_init_phy_bb(struct rtl8xxxu_priv *priv)
 		rtl8xxxu_write8(priv, REG_SYS_FUNC, 0xe3);
 		rtl8xxxu_write8(priv, REG_AFE_XTAL_CTRL + 1, 0x80);
 		rtl8xxxu_init_phy_regs(priv, rtl8723b_phy_1t_init_table);
+	} else if (priv->rtl_chip == RTL8192E) {
+		val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC);
+		val16 |= (SYS_FUNC_USBA | SYS_FUNC_USBD | SYS_FUNC_DIO_RF |
+			  SYS_FUNC_BB_GLB_RSTN | SYS_FUNC_BBRSTB);
+		rtl8xxxu_write16(priv, REG_SYS_FUNC, val16);
+		val8 = RF_ENABLE | RF_RSTB | RF_SDMRSTB;
+		rtl8xxxu_write8(priv, REG_RF_CTRL, val8);
+		rtl8xxxu_init_phy_regs(priv, rtl8192eu_phy_init_table);
 	} else
 		rtl8xxxu_init_phy_regs(priv, rtl8723a_phy_1t_init_table);
 
-- 
2.5.5

[PATCH 07/18] rtl8xxxu: Pick PHY init table based on chip version first

[Jes.Sorensen]

From: Jes Sorensen <Jes.Sorensen@redhat.com>

Pick PHY init table based on device before distinguishing between
1T/2T/high PA tables. The latter is only currently used for
8188cu/8192cu/8188ru.

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
---
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c | 13 ++++++-------
 1 file changed, 6 insertions(+), 7 deletions(-)

diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index fa6ab85..d6abe27 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -3637,11 +3637,7 @@ static int rtl8xxxu_init_phy_bb(struct rtl8xxxu_priv *priv)
 	val8 = RF_ENABLE | RF_RSTB | RF_SDMRSTB;
 	rtl8xxxu_write8(priv, REG_RF_CTRL, val8);
 
-	if (priv->hi_pa)
-		rtl8xxxu_init_phy_regs(priv, rtl8188ru_phy_1t_highpa_table);
-	else if (priv->tx_paths == 2)
-		rtl8xxxu_init_phy_regs(priv, rtl8192cu_phy_2t_init_table);
-	else if (priv->rtl_chip == RTL8723B) {
+	if (priv->rtl_chip == RTL8723B) {
 		/*
 		 * Why?
 		 */
@@ -3656,10 +3652,13 @@ static int rtl8xxxu_init_phy_bb(struct rtl8xxxu_priv *priv)
 		val8 = RF_ENABLE | RF_RSTB | RF_SDMRSTB;
 		rtl8xxxu_write8(priv, REG_RF_CTRL, val8);
 		rtl8xxxu_init_phy_regs(priv, rtl8192eu_phy_init_table);
-	} else
+	} else	if (priv->hi_pa)
+		rtl8xxxu_init_phy_regs(priv, rtl8188ru_phy_1t_highpa_table);
+	else if (priv->tx_paths == 2)
+		rtl8xxxu_init_phy_regs(priv, rtl8192cu_phy_2t_init_table);
+	else
 		rtl8xxxu_init_phy_regs(priv, rtl8723a_phy_1t_init_table);
 
-
 	if (priv->rtl_chip == RTL8188C && priv->hi_pa &&
 	    priv->vendor_umc && priv->chip_cut == 1)
 		rtl8xxxu_write8(priv, REG_OFDM0_AGC_PARM1 + 2, 0x50);
-- 
2.5.5

[PATCH 08/18] rtl8xxxu: Correctly parse 8192eu efuse

[Jes.Sorensen]

From: Jes Sorensen <Jes.Sorensen@redhat.com>

The 8192eu efuse only has power data for path A and B. It follows the
same layout as 8723bu.

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
---
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c | 40 ++++++++++++++++++++++++
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h | 38 ++++++++++------------
 2 files changed, 56 insertions(+), 22 deletions(-)

diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index d6abe27..b5b157f 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -2122,6 +2122,9 @@ static int rtl8723a_channel_to_group(int channel)
 	return group;
 }
 
+/*
+ * Valid for rtl8723bu and rtl8192eu
+ */
 static int rtl8723b_channel_to_group(int channel)
 {
 	int group;
@@ -2987,6 +2990,43 @@ static int rtl8192eu_parse_efuse(struct rtl8xxxu_priv *priv)
 
 	ether_addr_copy(priv->mac_addr, efuse->mac_addr);
 
+	memcpy(priv->cck_tx_power_index_A, efuse->tx_power_index_A.cck_base,
+	       sizeof(efuse->tx_power_index_A.cck_base));
+	memcpy(priv->cck_tx_power_index_B, efuse->tx_power_index_B.cck_base,
+	       sizeof(efuse->tx_power_index_B.cck_base));
+
+	memcpy(priv->ht40_1s_tx_power_index_A,
+	       efuse->tx_power_index_A.ht40_base,
+	       sizeof(efuse->tx_power_index_A.ht40_base));
+	memcpy(priv->ht40_1s_tx_power_index_B,
+	       efuse->tx_power_index_B.ht40_base,
+	       sizeof(efuse->tx_power_index_B.ht40_base));
+
+	priv->ht20_tx_power_diff[0].a =
+		efuse->tx_power_index_A.ht20_ofdm_1s_diff.b;
+	priv->ht20_tx_power_diff[0].b =
+		efuse->tx_power_index_B.ht20_ofdm_1s_diff.b;
+
+	priv->ht40_tx_power_diff[0].a = 0;
+	priv->ht40_tx_power_diff[0].b = 0;
+
+	for (i = 1; i < RTL8723B_TX_COUNT; i++) {
+		priv->ofdm_tx_power_diff[i].a =
+			efuse->tx_power_index_A.pwr_diff[i - 1].ofdm;
+		priv->ofdm_tx_power_diff[i].b =
+			efuse->tx_power_index_B.pwr_diff[i - 1].ofdm;
+
+		priv->ht20_tx_power_diff[i].a =
+			efuse->tx_power_index_A.pwr_diff[i - 1].ht20;
+		priv->ht20_tx_power_diff[i].b =
+			efuse->tx_power_index_B.pwr_diff[i - 1].ht20;
+
+		priv->ht40_tx_power_diff[i].a =
+			efuse->tx_power_index_A.pwr_diff[i - 1].ht40;
+		priv->ht40_tx_power_diff[i].b =
+			efuse->tx_power_index_B.pwr_diff[i - 1].ht40;
+	}
+
 	priv->has_xtalk = 1;
 	priv->xtalk = priv->efuse_wifi.efuse8192eu.xtal_k & 0x3f;
 
diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h
index 63d7268..48a80fa 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h
@@ -788,55 +788,49 @@ struct rtl8192eu_efuse_tx_power {
 	u8 cck_base[6];
 	u8 ht40_base[5];
 	struct rtl8723au_idx ht20_ofdm_1s_diff;
-	struct rtl8723au_idx ht40_ht20_2s_diff;
-	struct rtl8723au_idx ofdm_cck_2s_diff; /* not used */
-	struct rtl8723au_idx ht40_ht20_3s_diff;
-	struct rtl8723au_idx ofdm_cck_3s_diff; /* not used */
-	struct rtl8723au_idx ht40_ht20_4s_diff;
-	struct rtl8723au_idx ofdm_cck_4s_diff; /* not used */
+	struct rtl8723bu_pwr_idx pwr_diff[3];
+	u8 dummy5g[24]; /* max channel group (14) + power diff offset (10) */
 };
 
 struct rtl8192eu_efuse {
 	__le16 rtl_id;
 	u8 res0[0x0e];
 	struct rtl8192eu_efuse_tx_power tx_power_index_A;	/* 0x10 */
-	struct rtl8192eu_efuse_tx_power tx_power_index_B;	/* 0x22 */
-	struct rtl8192eu_efuse_tx_power tx_power_index_C;	/* 0x34 */
-	struct rtl8192eu_efuse_tx_power tx_power_index_D;	/* 0x46 */
-	u8 res1[0x60];
+	struct rtl8192eu_efuse_tx_power tx_power_index_B;	/* 0x3a */
+	u8 res2[0x54];
 	u8 channel_plan;		/* 0xb8 */
 	u8 xtal_k;
 	u8 thermal_meter;
 	u8 iqk_lck;
 	u8 pa_type;			/* 0xbc */
 	u8 lna_type_2g;			/* 0xbd */
-	u8 res2[1];
+	u8 res3[1];
 	u8 lna_type_5g;			/* 0xbf */
-	u8 res13[1];
+	u8 res4[1];
 	u8 rf_board_option;
 	u8 rf_feature_option;
 	u8 rf_bt_setting;
 	u8 eeprom_version;
 	u8 eeprom_customer_id;
-	u8 res3[3];
+	u8 res5[3];
 	u8 rf_antenna_option;		/* 0xc9 */
-	u8 res4[6];
+	u8 res6[6];
 	u8 vid;				/* 0xd0 */
-	u8 res5[1];
+	u8 res7[1];
 	u8 pid;				/* 0xd2 */
-	u8 res6[1];
+	u8 res8[1];
 	u8 usb_optional_function;
-	u8 res7[2];
+	u8 res9[2];
 	u8 mac_addr[ETH_ALEN];		/* 0xd7 */
-	u8 res8[2];
+	u8 res10[2];
 	u8 vendor_name[7];
-	u8 res9[2];
+	u8 res11[2];
 	u8 device_name[0x0b];		/* 0xe8 */
-	u8 res10[2];
+	u8 res12[2];
 	u8 serial[0x0b];		/* 0xf5 */
-	u8 res11[0x30];
+	u8 res13[0x30];
 	u8 unknown[0x0d];		/* 0x130 */
-	u8 res12[0xc3];
+	u8 res14[0xc3];
 };
 
 struct rtl8xxxu_reg8val {
-- 
2.5.5

[PATCH 09/18] rtl8xxxu: Handle BB init for 8192eu

[Jes.Sorensen]

From: Jes Sorensen <Jes.Sorensen@redhat.com>

The 8192eu does not use REG_AFE_PLL_CTRL in it's BB init sequence, so
provide device specific handling.

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
---
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index b5b157f..c3d69ff 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -3649,6 +3649,11 @@ static int rtl8xxxu_init_phy_bb(struct rtl8xxxu_priv *priv)
 		rtl8xxxu_write16(priv, REG_SYS_FUNC, val16);
 
 		rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00);
+	} else if (priv->rtl_chip == RTL8192E) {
+		val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC);
+		val16 |= SYS_FUNC_BB_GLB_RSTN | SYS_FUNC_BBRSTB |
+			SYS_FUNC_DIO_RF;
+		rtl8xxxu_write16(priv, REG_SYS_FUNC, val16);
 	} else {
 		val8 = rtl8xxxu_read8(priv, REG_AFE_PLL_CTRL);
 		udelay(2);
-- 
2.5.5

[PATCH 10/18] rtl8xxxu: Provide special handling when writing RF regs on 8192eu

[Jes.Sorensen]

From: Jes Sorensen <Jes.Sorensen@redhat.com>

The 8192eu requires clearing/restoring bit 17 in REG_FPGA0_POWER_SAVE
before/after writing RF registers.

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
---
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c | 14 +++++++++++++-
 1 file changed, 13 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index c3d69ff..356fdf3 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -1896,7 +1896,7 @@ static int rtl8xxxu_write_rfreg(struct rtl8xxxu_priv *priv,
 				enum rtl8xxxu_rfpath path, u8 reg, u32 data)
 {
 	int ret, retval;
-	u32 dataaddr;
+	u32 dataaddr, val32;
 
 	if (rtl8xxxu_debug & RTL8XXXU_DEBUG_RFREG_WRITE)
 		dev_info(&priv->udev->dev, "%s(%02x) = 0x%06x\n",
@@ -1905,6 +1905,12 @@ static int rtl8xxxu_write_rfreg(struct rtl8xxxu_priv *priv,
 	data &= FPGA0_LSSI_PARM_DATA_MASK;
 	dataaddr = (reg << FPGA0_LSSI_PARM_ADDR_SHIFT) | data;
 
+	if (priv->rtl_chip == RTL8192E) {
+		val32 = rtl8xxxu_read32(priv, REG_FPGA0_POWER_SAVE);
+		val32 &= ~0x20000;
+		rtl8xxxu_write32(priv, REG_FPGA0_POWER_SAVE, val32);
+	}
+
 	/* Use XB for path B */
 	ret = rtl8xxxu_write32(priv, rtl8xxxu_rfregs[path].lssiparm, dataaddr);
 	if (ret != sizeof(dataaddr))
@@ -1914,6 +1920,12 @@ static int rtl8xxxu_write_rfreg(struct rtl8xxxu_priv *priv,
 
 	udelay(1);
 
+	if (priv->rtl_chip == RTL8192E) {
+		val32 = rtl8xxxu_read32(priv, REG_FPGA0_POWER_SAVE);
+		val32 |= 0x20000;
+		rtl8xxxu_write32(priv, REG_FPGA0_POWER_SAVE, val32);
+	}
+
 	return retval;
 }
 
-- 
2.5.5

[PATCH 11/18] rtl8xxxu: Handle XTAL value setting on 8192eu

[Jes.Sorensen]

From: Jes Sorensen <Jes.Sorensen@redhat.com>

Set REG_AFE_XTAL_CTRL on 8192eu to the vendor driver value, and do not
skip setting REG_MAX_AGGR_NUM on 8192eu.

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
---
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index 356fdf3..3c732ed 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -3608,7 +3608,7 @@ rtl8xxxu_init_mac(struct rtl8xxxu_priv *priv)
 		}
 	}
 
-	if (priv->rtl_chip != RTL8723B)
+	if (priv->rtl_chip != RTL8723B && priv->rtl_chip != RTL8192E)
 		rtl8xxxu_write8(priv, REG_MAX_AGGR_NUM, 0x0a);
 
 	return 0;
@@ -3813,6 +3813,9 @@ static int rtl8xxxu_init_phy_bb(struct rtl8xxxu_priv *priv)
 		rtl8xxxu_write32(priv, REG_LDOA15_CTRL, val32);
 	}
 
+	if (priv->rtl_chip == RTL8192E)
+		rtl8xxxu_write32(priv, REG_AFE_XTAL_CTRL, 0x000f81fb);
+
 	return 0;
 }
 
-- 
2.5.5

[PATCH 12/18] rtl8xxxu: Set correct interrupt masking registers on 8192eu

[Jes.Sorensen]

From: Jes Sorensen <Jes.Sorensen@redhat.com>

Set HIMR[01] on 8192eu instead of HISR/HIMR. It's not obvious this
really matters for USB devices, but this matches the register writes
performed by the vendor driver.

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
---
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c | 20 ++++++++++----------
 1 file changed, 10 insertions(+), 10 deletions(-)

diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index 3c732ed..eac2a54 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -6883,11 +6883,6 @@ static int rtl8xxxu_init_device(struct ieee80211_hw *hw)
 		rtl8xxxu_write8(priv, 0xfe42, 0x80);
 	}
 
-	if (priv->rtl_chip == RTL8192E) {
-		rtl8xxxu_write32(priv, REG_HIMR0, 0x00);
-		rtl8xxxu_write32(priv, REG_HIMR1, 0x00);
-	}
-
 	if (priv->fops->phy_init_antenna_selection)
 		priv->fops->phy_init_antenna_selection(priv);
 
@@ -7053,11 +7048,16 @@ static int rtl8xxxu_init_device(struct ieee80211_hw *hw)
 	 */
 	rtl8xxxu_write8(priv, REG_RX_DRVINFO_SZ, 4);
 
-	/*
-	 * Enable all interrupts - not obvious USB needs to do this
-	 */
-	rtl8xxxu_write32(priv, REG_HISR, 0xffffffff);
-	rtl8xxxu_write32(priv, REG_HIMR, 0xffffffff);
+	if (priv->rtl_chip == RTL8192E) {
+		rtl8xxxu_write32(priv, REG_HIMR0, 0x00);
+		rtl8xxxu_write32(priv, REG_HIMR1, 0x00);
+	} else {
+		/*
+		 * Enable all interrupts - not obvious USB needs to do this
+		 */
+		rtl8xxxu_write32(priv, REG_HISR, 0xffffffff);
+		rtl8xxxu_write32(priv, REG_HIMR, 0xffffffff);
+	}
 
 	rtl8xxxu_set_mac(priv);
 	rtl8xxxu_set_linktype(priv, NL80211_IFTYPE_STATION);
-- 
2.5.5

[PATCH 13/18] rtl8xxxu: Set REG_USB_HRPWM for 8192eu

[Jes.Sorensen]

From: Jes Sorensen <Jes.Sorensen@redhat.com>

The vendor driver set register 0xfe58 REG_USB_HWPWM in it's init
sequence for 8192eu. Do the same here.

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
---
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c      | 2 ++
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h | 1 +
 2 files changed, 3 insertions(+)

diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index eac2a54..e06b25e 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -7225,6 +7225,8 @@ static int rtl8xxxu_init_device(struct ieee80211_hw *hw)
 			val32 |= FPGA_RF_MODE_CCK;
 			rtl8xxxu_write32(priv, REG_FPGA0_RF_MODE, val32);
 		}
+	} else if (priv->rtl_chip == RTL8192E) {
+		rtl8xxxu_write8(priv, REG_USB_HRPWM, 0x00);
 	}
 
 	val32 = rtl8xxxu_read32(priv, REG_FWHW_TXQ_CTRL);
diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h
index ade42fe..82cbe85 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h
@@ -1043,6 +1043,7 @@
 #define  USB_HIMR_ROK			BIT(0)	/*  Receive DMA OK Interrupt */
 
 #define REG_USB_SPECIAL_OPTION		0xfe55
+#define REG_USB_HRPWM			0xfe58
 #define REG_USB_DMA_AGG_TO		0xfe5b
 #define REG_USB_AGG_TO			0xfe5c
 #define REG_USB_AGG_TH			0xfe5d
-- 
2.5.5

[PATCH 14/18] rtl8xxxu: Fix LDPC RX hang issue on 8192eu

[Jes.Sorensen]

From: Jes Sorensen <Jes.Sorensen@redhat.com>

Implement workaround for LDPC RX hands on 8192eu. This was inspired by
workaround found in the 8192eu vendor driver.

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
---
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index e06b25e..c800882 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -7234,6 +7234,16 @@ static int rtl8xxxu_init_device(struct ieee80211_hw *hw)
 	/* ack for xmit mgmt frames. */
 	rtl8xxxu_write32(priv, REG_FWHW_TXQ_CTRL, val32);
 
+	if (priv->rtl_chip == RTL8192E) {
+		/*
+		 * Fix LDPC rx hang issue.
+		 */
+		val32 = rtl8xxxu_read32(priv, REG_AFE_MISC);
+		rtl8xxxu_write8(priv, REG_8192E_LDOV12_CTRL, 0x75);
+		val32 &= 0xfff00fff;
+		val32 |= 0x0007e000;
+		rtl8xxxu_write32(priv, REG_8192E_LDOV12_CTRL, val32);
+	}
 exit:
 	return ret;
 }
-- 
2.5.5

[PATCH 15/18] rtl8xxxu: Implement 8192eu device specific quirks

[Jes.Sorensen]

From: Jes Sorensen <Jes.Sorensen@redhat.com>

Set REG_QUEUE_CTRL and REG_ACLK_MON for 8192eu.

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
---
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c      | 14 ++++++++++++++
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h |  1 +
 2 files changed, 15 insertions(+)

diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index c800882..5a2eb0a 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -7197,6 +7197,20 @@ static int rtl8xxxu_init_device(struct ieee80211_hw *hw)
 	if (priv->fops->init_statistics)
 		priv->fops->init_statistics(priv);
 
+	if (priv->rtl_chip == RTL8192E) {
+		/*
+		 * 0x4c6[3] 1: RTS BW = Data BW
+		 * 0: RTS BW depends on CCA / secondary CCA result.
+		 */
+		val8 = rtl8xxxu_read8(priv, REG_QUEUE_CTRL);
+		val8 &= ~BIT(3);
+		rtl8xxxu_write8(priv, REG_QUEUE_CTRL, val8);
+		/*
+		 * Reset USB mode switch setting
+		 */
+		rtl8xxxu_write8(priv, REG_ACLK_MON, 0x00);
+	}
+
 	rtl8723a_phy_lc_calibrate(priv);
 
 	priv->fops->phy_iq_calibrate(priv);
diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h
index 82cbe85..c19f234 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h
@@ -512,6 +512,7 @@
 #define REG_PKT_VO_VI_LIFE_TIME		0x04c0
 #define REG_PKT_BE_BK_LIFE_TIME		0x04c2
 #define REG_STBC_SETTING		0x04c4
+#define REG_QUEUE_CTRL			0x04c6
 #define REG_HT_SINGLE_AMPDU_8723B	0x04c7
 #define REG_PROT_MODE_CTRL		0x04c8
 #define REG_MAX_AGGR_NUM		0x04ca
-- 
2.5.5

[PATCH 16/18] rtl8xxxu: Use proper register name for REG_PAD_CTRL1

[Jes.Sorensen]

From: Jes Sorensen <Jes.Sorensen@redhat.com>

Fixup another case where the hard coded register value was used
instead of the name.

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
---
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index 5a2eb0a..604deb4 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -3550,9 +3550,9 @@ static void rtl8723bu_phy_init_antenna_selection(struct rtl8xxxu_priv *priv)
 {
 	u32 val32;
 
-	val32 = rtl8xxxu_read32(priv, 0x64);
+	val32 = rtl8xxxu_read32(priv, REG_PAD_CTRL1);
 	val32 &= ~(BIT(20) | BIT(24));
-	rtl8xxxu_write32(priv, 0x64, val32);
+	rtl8xxxu_write32(priv, REG_PAD_CTRL1, val32);
 
 	val32 = rtl8xxxu_read32(priv, REG_GPIO_MUXCFG);
 	val32 &= ~BIT(4);
-- 
2.5.5

[PATCH 17/18] rtl8xxxu: Implement IQK calibration for 8192eu

[Jes.Sorensen]

From: Jes Sorensen <Jes.Sorensen@redhat.com>

8192eu has it's own IQK calibration procedure, and notably uses
undocumented RF register 0x56 in the process.

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
---
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c   | 608 ++++++++++++++++++++-
 .../net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h  |   1 +
 2 files changed, 608 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index 604deb4..61c0ece 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -4955,6 +4955,334 @@ out:
 }
 #endif
 
+static int rtl8192eu_iqk_path_a(struct rtl8xxxu_priv *priv)
+{
+	u32 reg_eac, reg_e94, reg_e9c;
+	int result = 0;
+
+	/*
+	 * TX IQK
+	 * PA/PAD controlled by 0x0
+	 */
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_DF, 0x00180);
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x80800000);
+
+	/* Path A IQK setting */
+	rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x18008c1c);
+	rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x38008c1c);
+	rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c);
+	rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c);
+
+	rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82140303);
+	rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x68160000);
+
+	/* LO calibration setting */
+	rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x00462911);
+
+	/* One shot, path A LOK & IQK */
+	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000);
+	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
+
+	mdelay(10);
+
+	/* Check failed */
+	reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
+	reg_e94 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_A);
+	reg_e9c = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_A);
+
+	if (!(reg_eac & BIT(28)) &&
+	    ((reg_e94 & 0x03ff0000) != 0x01420000) &&
+	    ((reg_e9c & 0x03ff0000) != 0x00420000))
+		result |= 0x01;
+
+	return result;
+}
+
+static int rtl8192eu_rx_iqk_path_a(struct rtl8xxxu_priv *priv)
+{
+	u32 reg_ea4, reg_eac, reg_e94, reg_e9c, val32;
+	int result = 0;
+
+	/* Leave IQK mode */
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00);
+
+	/* Enable path A PA in TX IQK mode */
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, 0x800a0);
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000);
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0000f);
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf117b);
+
+	/* PA/PAD control by 0x56, and set = 0x0 */
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_DF, 0x00980);
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_56, 0x51000);
+
+	/* Enter IQK mode */
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x80800000);
+
+	/* TX IQK setting */
+	rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00);
+	rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800);
+
+	/* path-A IQK setting */
+	rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x18008c1c);
+	rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x38008c1c);
+	rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c);
+	rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c);
+
+	rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82160c1f);
+	rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x68160c1f);
+
+	/* LO calibration setting */
+	rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x0046a911);
+
+	/* One shot, path A LOK & IQK */
+	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xfa000000);
+	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
+
+	mdelay(10);
+
+	/* Check failed */
+	reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
+	reg_e94 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_A);
+	reg_e9c = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_A);
+
+	if (!(reg_eac & BIT(28)) &&
+	    ((reg_e94 & 0x03ff0000) != 0x01420000) &&
+	    ((reg_e9c & 0x03ff0000) != 0x00420000)) {
+		result |= 0x01;
+	} else {
+		/* PA/PAD controlled by 0x0 */
+		rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+		rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_DF, 0x180);
+		goto out;
+	}
+
+	val32 = 0x80007c00 |
+		(reg_e94 & 0x03ff0000) | ((reg_e9c >> 16) & 0x03ff);
+	rtl8xxxu_write32(priv, REG_TX_IQK, val32);
+
+	/* Modify RX IQK mode table */
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, 0x800a0);
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000);
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0000f);
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf7ffa);
+
+	/* PA/PAD control by 0x56, and set = 0x0 */
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_DF, 0x00980);
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_56, 0x51000);
+
+	/* Enter IQK mode */
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x80800000);
+
+	/* IQK setting */
+	rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800);
+
+	/* Path A IQK setting */
+	rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x38008c1c);
+	rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x18008c1c);
+	rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c);
+	rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c);
+
+	rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82160c1f);
+	rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x28160c1f);
+
+	/* LO calibration setting */
+	rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x0046a891);
+
+	/* One shot, path A LOK & IQK */
+	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xfa000000);
+	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
+
+	mdelay(10);
+
+	reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
+	reg_ea4 = rtl8xxxu_read32(priv, REG_RX_POWER_BEFORE_IQK_A_2);
+
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_DF, 0x180);
+
+	if (!(reg_eac & BIT(27)) &&
+	    ((reg_ea4 & 0x03ff0000) != 0x01320000) &&
+	    ((reg_eac & 0x03ff0000) != 0x00360000))
+		result |= 0x02;
+	else
+		dev_warn(&priv->udev->dev, "%s: Path A RX IQK failed!\n",
+			 __func__);
+
+out:
+	return result;
+}
+
+static int rtl8192eu_iqk_path_b(struct rtl8xxxu_priv *priv)
+{
+	u32 reg_eac, reg_eb4, reg_ebc;
+	int result = 0;
+
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+	rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_UNKNOWN_DF, 0x00180);
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x80800000);
+
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x80800000);
+
+	/* Path B IQK setting */
+	rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x38008c1c);
+	rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x38008c1c);
+	rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x18008c1c);
+	rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c);
+
+	rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x821403e2);
+	rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x68160000);
+
+	/* LO calibration setting */
+	rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x00492911);
+
+	/* One shot, path A LOK & IQK */
+	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xfa000000);
+	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
+
+	mdelay(1);
+
+	/* Check failed */
+	reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
+	reg_eb4 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_B);
+	reg_ebc = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_B);
+
+	if (!(reg_eac & BIT(31)) &&
+	    ((reg_eb4 & 0x03ff0000) != 0x01420000) &&
+	    ((reg_ebc & 0x03ff0000) != 0x00420000))
+		result |= 0x01;
+	else
+		dev_warn(&priv->udev->dev, "%s: Path B IQK failed!\n",
+			 __func__);
+
+	return result;
+}
+
+static int rtl8192eu_rx_iqk_path_b(struct rtl8xxxu_priv *priv)
+{
+	u32 reg_eac, reg_eb4, reg_ebc, reg_ec4, reg_ecc, val32;
+	int result = 0;
+
+	/* Leave IQK mode */
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+
+	/* Enable path A PA in TX IQK mode */
+	rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_WE_LUT, 0x800a0);
+	rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_RCK_OS, 0x30000);
+	rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_TXPA_G1, 0x0000f);
+	rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_TXPA_G2, 0xf117b);
+
+	/* PA/PAD control by 0x56, and set = 0x0 */
+	rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_UNKNOWN_DF, 0x00980);
+	rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_UNKNOWN_56, 0x51000);
+
+	/* Enter IQK mode */
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x80800000);
+
+	/* TX IQK setting */
+	rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00);
+	rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800);
+
+	/* path-A IQK setting */
+	rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x38008c1c);
+	rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x38008c1c);
+	rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x18008c1c);
+	rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c);
+
+	rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x82160c1f);
+	rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x68160c1f);
+
+	/* LO calibration setting */
+	rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x0046a911);
+
+	/* One shot, path A LOK & IQK */
+	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xfa000000);
+	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
+
+	mdelay(10);
+
+	/* Check failed */
+	reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
+	reg_eb4 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_B);
+	reg_ebc = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_B);
+
+	if (!(reg_eac & BIT(31)) &&
+	    ((reg_eb4 & 0x03ff0000) != 0x01420000) &&
+	    ((reg_ebc & 0x03ff0000) != 0x00420000)) {
+		result |= 0x01;
+	} else {
+		/*
+		 * PA/PAD controlled by 0x0
+		 * Vendor driver restores RF_A here which I believe is a bug
+		 */
+		rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+		rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_UNKNOWN_DF, 0x180);
+		goto out;
+	}
+
+	val32 = 0x80007c00 |
+		(reg_eb4 & 0x03ff0000) | ((reg_ebc >> 16) & 0x03ff);
+	rtl8xxxu_write32(priv, REG_TX_IQK, val32);
+
+	/* Modify RX IQK mode table */
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+
+	rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_WE_LUT, 0x800a0);
+	rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_RCK_OS, 0x30000);
+	rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_TXPA_G1, 0x0000f);
+	rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_TXPA_G2, 0xf7ffa);
+
+	/* PA/PAD control by 0x56, and set = 0x0 */
+	rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_UNKNOWN_DF, 0x00980);
+	rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_UNKNOWN_56, 0x51000);
+
+	/* Enter IQK mode */
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x80800000);
+
+	/* IQK setting */
+	rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800);
+
+	/* Path A IQK setting */
+	rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x38008c1c);
+	rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x38008c1c);
+	rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c);
+	rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x18008c1c);
+
+	rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82160c1f);
+	rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x28160c1f);
+
+	/* LO calibration setting */
+	rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x0046a891);
+
+	/* One shot, path A LOK & IQK */
+	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xfa000000);
+	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
+
+	mdelay(10);
+
+	reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
+	reg_ec4 = rtl8xxxu_read32(priv, REG_RX_POWER_BEFORE_IQK_B_2);
+	reg_ecc = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_B_2);
+
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+	rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_UNKNOWN_DF, 0x180);
+
+	if (!(reg_eac & BIT(30)) &&
+	    ((reg_ec4 & 0x03ff0000) != 0x01320000) &&
+	    ((reg_ecc & 0x03ff0000) != 0x00360000))
+		result |= 0x02;
+	else
+		dev_warn(&priv->udev->dev, "%s: Path B RX IQK failed!\n",
+			 __func__);
+
+out:
+	return result;
+}
+
 static void rtl8xxxu_phy_iqcalibrate(struct rtl8xxxu_priv *priv,
 				     int result[][8], int t)
 {
@@ -5385,6 +5713,194 @@ static void rtl8723bu_phy_iqcalibrate(struct rtl8xxxu_priv *priv,
 	}
 }
 
+static void rtl8192eu_phy_iqcalibrate(struct rtl8xxxu_priv *priv,
+				      int result[][8], int t)
+{
+	struct device *dev = &priv->udev->dev;
+	u32 i, val32;
+	int path_a_ok, path_b_ok;
+	int retry = 2;
+	const u32 adda_regs[RTL8XXXU_ADDA_REGS] = {
+		REG_FPGA0_XCD_SWITCH_CTRL, REG_BLUETOOTH,
+		REG_RX_WAIT_CCA, REG_TX_CCK_RFON,
+		REG_TX_CCK_BBON, REG_TX_OFDM_RFON,
+		REG_TX_OFDM_BBON, REG_TX_TO_RX,
+		REG_TX_TO_TX, REG_RX_CCK,
+		REG_RX_OFDM, REG_RX_WAIT_RIFS,
+		REG_RX_TO_RX, REG_STANDBY,
+		REG_SLEEP, REG_PMPD_ANAEN
+	};
+	const u32 iqk_mac_regs[RTL8XXXU_MAC_REGS] = {
+		REG_TXPAUSE, REG_BEACON_CTRL,
+		REG_BEACON_CTRL_1, REG_GPIO_MUXCFG
+	};
+	const u32 iqk_bb_regs[RTL8XXXU_BB_REGS] = {
+		REG_OFDM0_TRX_PATH_ENABLE, REG_OFDM0_TR_MUX_PAR,
+		REG_FPGA0_XCD_RF_SW_CTRL, REG_CONFIG_ANT_A, REG_CONFIG_ANT_B,
+		REG_FPGA0_XAB_RF_SW_CTRL, REG_FPGA0_XA_RF_INT_OE,
+		REG_FPGA0_XB_RF_INT_OE, REG_CCK0_AFE_SETTING
+	};
+	u8 xa_agc = rtl8xxxu_read32(priv, REG_OFDM0_XA_AGC_CORE1) & 0xff;
+	u8 xb_agc = rtl8xxxu_read32(priv, REG_OFDM0_XB_AGC_CORE1) & 0xff;
+
+	/*
+	 * Note: IQ calibration must be performed after loading
+	 *       PHY_REG.txt , and radio_a, radio_b.txt
+	 */
+
+	if (t == 0) {
+		/* Save ADDA parameters, turn Path A ADDA on */
+		rtl8xxxu_save_regs(priv, adda_regs, priv->adda_backup,
+				   RTL8XXXU_ADDA_REGS);
+		rtl8xxxu_save_mac_regs(priv, iqk_mac_regs, priv->mac_backup);
+		rtl8xxxu_save_regs(priv, iqk_bb_regs,
+				   priv->bb_backup, RTL8XXXU_BB_REGS);
+	}
+
+	rtl8xxxu_path_adda_on(priv, adda_regs, true);
+
+	/* MAC settings */
+	rtl8xxxu_mac_calibration(priv, iqk_mac_regs, priv->mac_backup);
+
+	val32 = rtl8xxxu_read32(priv, REG_CCK0_AFE_SETTING);
+	val32 |= 0x0f000000;
+	rtl8xxxu_write32(priv, REG_CCK0_AFE_SETTING, val32);
+
+	rtl8xxxu_write32(priv, REG_OFDM0_TRX_PATH_ENABLE, 0x03a05600);
+	rtl8xxxu_write32(priv, REG_OFDM0_TR_MUX_PAR, 0x000800e4);
+	rtl8xxxu_write32(priv, REG_FPGA0_XCD_RF_SW_CTRL, 0x22208200);
+
+	val32 = rtl8xxxu_read32(priv, REG_FPGA0_XAB_RF_SW_CTRL);
+	val32 |= (FPGA0_RF_PAPE | (FPGA0_RF_PAPE << FPGA0_RF_BD_CTRL_SHIFT));
+	rtl8xxxu_write32(priv, REG_FPGA0_XAB_RF_SW_CTRL, val32);
+
+	val32 = rtl8xxxu_read32(priv, REG_FPGA0_XA_RF_INT_OE);
+	val32 |= BIT(10);
+	rtl8xxxu_write32(priv, REG_FPGA0_XA_RF_INT_OE, val32);
+	val32 = rtl8xxxu_read32(priv, REG_FPGA0_XB_RF_INT_OE);
+	val32 |= BIT(10);
+	rtl8xxxu_write32(priv, REG_FPGA0_XB_RF_INT_OE, val32);
+
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x80800000);
+	rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00);
+	rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800);
+
+	for (i = 0; i < retry; i++) {
+		path_a_ok = rtl8192eu_iqk_path_a(priv);
+		if (path_a_ok == 0x01) {
+			val32 = rtl8xxxu_read32(priv,
+						REG_TX_POWER_BEFORE_IQK_A);
+			result[t][0] = (val32 >> 16) & 0x3ff;
+			val32 = rtl8xxxu_read32(priv,
+						REG_TX_POWER_AFTER_IQK_A);
+			result[t][1] = (val32 >> 16) & 0x3ff;
+
+			break;
+		}
+	}
+
+	if (!path_a_ok)
+		dev_dbg(dev, "%s: Path A TX IQK failed!\n", __func__);
+
+	for (i = 0; i < retry; i++) {
+		path_a_ok = rtl8192eu_rx_iqk_path_a(priv);
+		if (path_a_ok == 0x03) {
+			val32 = rtl8xxxu_read32(priv,
+						REG_RX_POWER_BEFORE_IQK_A_2);
+			result[t][2] = (val32 >> 16) & 0x3ff;
+			val32 = rtl8xxxu_read32(priv,
+						REG_RX_POWER_AFTER_IQK_A_2);
+			result[t][3] = (val32 >> 16) & 0x3ff;
+
+			break;
+		}
+	}
+
+	if (!path_a_ok)
+		dev_dbg(dev, "%s: Path A RX IQK failed!\n", __func__);
+
+	if (priv->rf_paths > 1) {
+		dev_warn(dev, "%s: Path B ongoing\n", __func__);
+
+		/* Path A into standby */
+		rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+		rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_AC, 0x10000);
+		rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x80800000);
+
+		/* Turn Path B ADDA on */
+		rtl8xxxu_path_adda_on(priv, adda_regs, false);
+
+		rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x80800000);
+		rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00);
+		rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800);
+
+		for (i = 0; i < retry; i++) {
+			path_b_ok = rtl8192eu_iqk_path_b(priv);
+			if (path_b_ok == 0x01) {
+				val32 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_B);
+				result[t][4] = (val32 >> 16) & 0x3ff;
+				val32 = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_B);
+				result[t][5] = (val32 >> 16) & 0x3ff;
+				break;
+			}
+		}
+
+		if (!path_b_ok)
+			dev_dbg(dev, "%s: Path B IQK failed!\n", __func__);
+
+		for (i = 0; i < retry; i++) {
+			path_b_ok = rtl8192eu_rx_iqk_path_b(priv);
+			if (path_a_ok == 0x03) {
+				val32 = rtl8xxxu_read32(priv,
+							REG_RX_POWER_BEFORE_IQK_B_2);
+				result[t][6] = (val32 >> 16) & 0x3ff;
+				val32 = rtl8xxxu_read32(priv,
+							REG_RX_POWER_AFTER_IQK_B_2);
+				result[t][7] = (val32 >> 16) & 0x3ff;
+				break;
+			}
+		}
+
+		if (!path_b_ok)
+			dev_dbg(dev, "%s: Path B RX IQK failed!\n", __func__);
+	}
+
+	/* Back to BB mode, load original value */
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+
+	if (t) {
+		/* Reload ADDA power saving parameters */
+		rtl8xxxu_restore_regs(priv, adda_regs, priv->adda_backup,
+				      RTL8XXXU_ADDA_REGS);
+
+		/* Reload MAC parameters */
+		rtl8xxxu_restore_mac_regs(priv, iqk_mac_regs, priv->mac_backup);
+
+		/* Reload BB parameters */
+		rtl8xxxu_restore_regs(priv, iqk_bb_regs,
+				      priv->bb_backup, RTL8XXXU_BB_REGS);
+
+		/* Restore RX initial gain */
+		val32 = rtl8xxxu_read32(priv, REG_OFDM0_XA_AGC_CORE1);
+		val32 &= 0xffffff00;
+		rtl8xxxu_write32(priv, REG_OFDM0_XA_AGC_CORE1, val32 | 0x50);
+		rtl8xxxu_write32(priv, REG_OFDM0_XA_AGC_CORE1, val32 | xa_agc);
+
+		if (priv->rf_paths > 1) {
+			val32 = rtl8xxxu_read32(priv, REG_OFDM0_XB_AGC_CORE1);
+			val32 &= 0xffffff00;
+			rtl8xxxu_write32(priv, REG_OFDM0_XB_AGC_CORE1,
+					 val32 | 0x50);
+			rtl8xxxu_write32(priv, REG_OFDM0_XB_AGC_CORE1,
+					 val32 | xb_agc);
+		}
+
+		/* Load 0xe30 IQC default value */
+		rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x01008c00);
+		rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x01008c00);
+	}
+}
+
 static void rtl8xxxu_prepare_calibrate(struct rtl8xxxu_priv *priv, u8 start)
 {
 	struct h2c_cmd h2c;
@@ -5630,6 +6146,96 @@ static void rtl8723bu_phy_iq_calibrate(struct rtl8xxxu_priv *priv)
 	rtl8xxxu_prepare_calibrate(priv, 0);
 }
 
+static void rtl8192eu_phy_iq_calibrate(struct rtl8xxxu_priv *priv)
+{
+	struct device *dev = &priv->udev->dev;
+	int result[4][8];	/* last is final result */
+	int i, candidate;
+	bool path_a_ok, path_b_ok;
+	u32 reg_e94, reg_e9c, reg_ea4, reg_eac;
+	u32 reg_eb4, reg_ebc, reg_ec4, reg_ecc;
+	bool simu;
+
+	memset(result, 0, sizeof(result));
+	candidate = -1;
+
+	path_a_ok = false;
+	path_b_ok = false;
+
+	for (i = 0; i < 3; i++) {
+		rtl8192eu_phy_iqcalibrate(priv, result, i);
+
+		if (i == 1) {
+			simu = rtl8723bu_simularity_compare(priv, result, 0, 1);
+			if (simu) {
+				candidate = 0;
+				break;
+			}
+		}
+
+		if (i == 2) {
+			simu = rtl8723bu_simularity_compare(priv, result, 0, 2);
+			if (simu) {
+				candidate = 0;
+				break;
+			}
+
+			simu = rtl8723bu_simularity_compare(priv, result, 1, 2);
+			if (simu)
+				candidate = 1;
+			else
+				candidate = 3;
+		}
+	}
+
+	for (i = 0; i < 4; i++) {
+		reg_e94 = result[i][0];
+		reg_e9c = result[i][1];
+		reg_ea4 = result[i][2];
+		reg_eac = result[i][3];
+		reg_eb4 = result[i][4];
+		reg_ebc = result[i][5];
+		reg_ec4 = result[i][6];
+		reg_ecc = result[i][7];
+	}
+
+	if (candidate >= 0) {
+		reg_e94 = result[candidate][0];
+		priv->rege94 =  reg_e94;
+		reg_e9c = result[candidate][1];
+		priv->rege9c = reg_e9c;
+		reg_ea4 = result[candidate][2];
+		reg_eac = result[candidate][3];
+		reg_eb4 = result[candidate][4];
+		priv->regeb4 = reg_eb4;
+		reg_ebc = result[candidate][5];
+		priv->regebc = reg_ebc;
+		reg_ec4 = result[candidate][6];
+		reg_ecc = result[candidate][7];
+		dev_dbg(dev, "%s: candidate is %x\n", __func__, candidate);
+		dev_dbg(dev,
+			"%s: e94 =%x e9c=%x ea4=%x eac=%x eb4=%x ebc=%x ec4=%x "
+			"ecc=%x\n ", __func__, reg_e94, reg_e9c,
+			reg_ea4, reg_eac, reg_eb4, reg_ebc, reg_ec4, reg_ecc);
+		path_a_ok = true;
+		path_b_ok = true;
+	} else {
+		reg_e94 = reg_eb4 = priv->rege94 = priv->regeb4 = 0x100;
+		reg_e9c = reg_ebc = priv->rege9c = priv->regebc = 0x0;
+	}
+
+	if (reg_e94 && candidate >= 0)
+		rtl8xxxu_fill_iqk_matrix_a(priv, path_a_ok, result,
+					   candidate, (reg_ea4 == 0));
+
+	if (priv->rf_paths > 1)
+		rtl8xxxu_fill_iqk_matrix_b(priv, path_b_ok, result,
+					   candidate, (reg_ec4 == 0));
+
+	rtl8xxxu_save_regs(priv, rtl8723au_iqk_phy_iq_bb_reg,
+			   priv->bb_recovery_backup, RTL8XXXU_BB_REGS);
+}
+
 static void rtl8723a_phy_lc_calibrate(struct rtl8xxxu_priv *priv)
 {
 	u32 val32;
@@ -9080,7 +9686,7 @@ static struct rtl8xxxu_fileops rtl8192eu_fops = {
 	.power_off = rtl8xxxu_power_off,
 	.reset_8051 = rtl8xxxu_reset_8051,
 	.llt_init = rtl8xxxu_auto_llt_table,
-	.phy_iq_calibrate = rtl8723bu_phy_iq_calibrate,
+	.phy_iq_calibrate = rtl8192eu_phy_iq_calibrate,
 	.config_channel = rtl8723bu_config_channel,
 	.parse_rx_desc = rtl8723bu_parse_rx_desc,
 	.enable_rf = rtl8723b_enable_rf,
diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h
index c19f234..2aa14b1 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h
@@ -1130,6 +1130,7 @@
 #define RF6052_REG_T_METER_8723B	0x42
 #define RF6052_REG_UNKNOWN_43		0x43
 #define RF6052_REG_UNKNOWN_55		0x55
+#define RF6052_REG_UNKNOWN_56		0x56
 #define RF6052_REG_S0S1			0xb0
 #define RF6052_REG_UNKNOWN_DF		0xdf
 #define RF6052_REG_UNKNOWN_ED		0xed
-- 
2.5.5

[PATCH 18/18] rtl8xxxu: Adjust AFE crystal value on 8192eu

[Jes.Sorensen]

From: Jes Sorensen <Jes.Sorensen@redhat.com>

Adjust AFE before enabling PLL on 8192eu, probably also needed for
8723bu.

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
---
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c   | 39 ++++++++++++++++++++++
 .../net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h  |  4 +++
 2 files changed, 43 insertions(+)

diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index 61c0ece..b8cd42e 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -7093,6 +7093,41 @@ static int rtl8192cu_power_on(struct rtl8xxxu_priv *priv)
 
 #endif
 
+/*
+ * This is needed for 8723bu as well, presumable
+ */
+static void rtl8192e_crystal_afe_adjust(struct rtl8xxxu_priv *priv)
+{
+	u8 val8;
+	u32 val32;
+
+	/*
+	 * 40Mhz crystal source, MAC 0x28[2]=0
+	 */
+	val8 = rtl8xxxu_read8(priv, REG_AFE_PLL_CTRL);
+	val8 &= 0xfb;
+	rtl8xxxu_write8(priv, REG_AFE_PLL_CTRL, val8);
+
+	val32 = rtl8xxxu_read32(priv, REG_AFE_CTRL4);
+	val32 &= 0xfffffc7f;
+	rtl8xxxu_write32(priv, REG_AFE_CTRL4, val32);
+
+	/*
+	 * 92e AFE parameter
+	 * AFE PLL KVCO selection, MAC 0x28[6]=1
+	 */
+	val8 = rtl8xxxu_read8(priv, REG_AFE_PLL_CTRL);
+	val8 &= 0xbf;
+	rtl8xxxu_write8(priv, REG_AFE_PLL_CTRL, val8);
+
+	/*
+	 * AFE PLL KVCO selection, MAC 0x78[21]=0
+	 */
+	val32 = rtl8xxxu_read32(priv, REG_AFE_CTRL4);
+	val32 &= 0xffdfffff;
+	rtl8xxxu_write32(priv, REG_AFE_CTRL4, val32);
+}
+
 static int rtl8192eu_power_on(struct rtl8xxxu_priv *priv)
 {
 	u16 val16;
@@ -7115,6 +7150,10 @@ static int rtl8192eu_power_on(struct rtl8xxxu_priv *priv)
 		rtl8xxxu_write8(priv, REG_LDO_SW_CTRL, 0x83);
 	}
 
+	/*
+	 * Adjust AFE before enabling PLL
+	 */
+	rtl8192e_crystal_afe_adjust(priv);
 	rtl8192e_disabled_to_emu(priv);
 
 	ret = rtl8192e_emu_to_active(priv);
diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h
index 2aa14b1..bb08a39 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h
@@ -109,6 +109,9 @@
 #define  AFE_XTAL_GATE_DIG		BIT(17)
 #define  AFE_XTAL_BT_GATE		BIT(20)
 
+/*
+ * 0x0028 is also known as REG_AFE_CTRL2 on 8723bu/8192eu
+ */
 #define REG_AFE_PLL_CTRL		0x0028
 #define  AFE_PLL_ENABLE			BIT(0)
 #define  AFE_PLL_320_ENABLE		BIT(1)
@@ -192,6 +195,7 @@
 						   control */
 #define  MULTI_GPS_FUNC_EN		BIT(22)	/* GPS function enable */
 
+#define REG_AFE_CTRL4			0x0078	/* 8192eu/8723bu */
 #define REG_LDO_SW_CTRL			0x007c	/* 8192eu */
 
 #define REG_MCU_FW_DL			0x0080
-- 
2.5.5

Re: [01/18] rtl8xxxu: Add MAC init table for 8192eu

[Kalle Valo]

> From: Jes Sorensen <Jes.Sorensen@redhat.com>
> 
> The 8192eu requires a different MAC init table. Add the missing table
> and specify the table to use in the fileops structure.
> 
> Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>

Thanks, 18 patches applied to wireless-drivers-next.git:

c606e662a5c8 rtl8xxxu: Add MAC init table for 8192eu
2ca73dc786c4 rtl8xxxu: Do not mess with AFE_XTAL_CTRL on 8192eu
80805aa5f33e rtl8xxxu: Set TX page boundaries for 8192eu
19102f841934 rtl8xxxu: Add radio init tables for 8192eu
e293278debe7 rtl8xxxu: Add 8192eu AGC tables
ae14c5d20dc9 rtl8xxxu: Add 8192eu PHY init table
abd71bdb94c3 rtl8xxxu: Pick PHY init table based on chip version first
9e24772ae222 rtl8xxxu: Correctly parse 8192eu efuse
444004bd1349 rtl8xxxu: Handle BB init for 8192eu
2949b9ee77b8 rtl8xxxu: Provide special handling when writing RF regs on 8192eu
8a59485c8ee9 rtl8xxxu: Handle XTAL value setting on 8192eu
57e5e2e650fb rtl8xxxu: Set correct interrupt masking registers on 8192eu
3021e51f2b2f rtl8xxxu: Set REG_USB_HRPWM for 8192eu
e1394fe5f986 rtl8xxxu: Fix LDPC RX hang issue on 8192eu
b052b7fc7d25 rtl8xxxu: Implement 8192eu device specific quirks
70bc1e24d9e2 rtl8xxxu: Use proper register name for REG_PAD_CTRL1
f991f4e9147b rtl8xxxu: Implement IQK calibration for 8192eu
28e460b02c66 rtl8xxxu: Adjust AFE crystal value on 8192eu

Kalle Valo