[PATCH 0/8] ARM: dts: bcm283x: add and use pinctrl groups

[PATCH 0/8] ARM: dts: bcm283x: add and use pinctrl groups

[Gerd Hoffmann]

  Hi,

Patches 1-4 of this series add pinctrl group declarations for the
bcm283x.  Picked them up from Eric's git branches and the rpi mailing
list.  They alone should not break anything as they have no effect at
all without patches 5-8.  But even unused pinctrl groups are useful to
have for documentation purposes, so I'd like to see those land in the
next merge window even in case patches 5-8 are considered to be too
risky.

Patches 5-8 put some of these pinctrl groups into use, by adding them
to the devices they belong to (and removing the pins from &gpio at the
same time).  That should in theory not break anything too as we only move
the pinctrl setup to another place, but you never know ...

I've tested it on rpi2 and rpi3 hardware without any problems showing up.
/sys/kernel/debug/pinctrl/3f200000.gpio/pinmux-pins is more informative
with the patches applied.

cheers,
  Gerd

Eric Anholt (3):
  ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.
  ARM: dts: bcm283x: Add a group for mapping pins 48-53 to sdhost.
  ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

Gerd Hoffmann (5):
  ARM: dts: bcm283x: Add the emmc pin group to bcm283x.dtsi.
  ARM: dts: bcm283x: add pinctrl group to &pwm, drop pins from &gpio
  ARM: dts: bcm283x: add pinctrl group to &i2c0, drop pins from &gpio
  ARM: dts: bcm283x: add pinctrl group to &i2c1, drop pins from &gpio
  ARM: dts: bcm283x: add pinctrl group to &sdhci, drop pins from &gpio

 arch/arm/boot/dts/bcm2835-rpi.dtsi |  12 ++-
 arch/arm/boot/dts/bcm283x.dtsi     | 183 +++++++++++++++++++++++++++++++++++++
 2 files changed, 193 insertions(+), 2 deletions(-)

-- 
1.8.3.1

[PATCH 0/8] ARM: dts: bcm283x: add and use pinctrl groups

[Gerd Hoffmann]

  Hi,

Patches 1-4 of this series add pinctrl group declarations for the
bcm283x.  Picked them up from Eric's git branches and the rpi mailing
list.  They alone should not break anything as they have no effect at
all without patches 5-8.  But even unused pinctrl groups are useful to
have for documentation purposes, so I'd like to see those land in the
next merge window even in case patches 5-8 are considered to be too
risky.

Patches 5-8 put some of these pinctrl groups into use, by adding them
to the devices they belong to (and removing the pins from &gpio at the
same time).  That should in theory not break anything too as we only move
the pinctrl setup to another place, but you never know ...

I've tested it on rpi2 and rpi3 hardware without any problems showing up.
/sys/kernel/debug/pinctrl/3f200000.gpio/pinmux-pins is more informative
with the patches applied.

cheers,
  Gerd

Eric Anholt (3):
  ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.
  ARM: dts: bcm283x: Add a group for mapping pins 48-53 to sdhost.
  ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

Gerd Hoffmann (5):
  ARM: dts: bcm283x: Add the emmc pin group to bcm283x.dtsi.
  ARM: dts: bcm283x: add pinctrl group to &pwm, drop pins from &gpio
  ARM: dts: bcm283x: add pinctrl group to &i2c0, drop pins from &gpio
  ARM: dts: bcm283x: add pinctrl group to &i2c1, drop pins from &gpio
  ARM: dts: bcm283x: add pinctrl group to &sdhci, drop pins from &gpio

 arch/arm/boot/dts/bcm2835-rpi.dtsi |  12 ++-
 arch/arm/boot/dts/bcm283x.dtsi     | 183 +++++++++++++++++++++++++++++++++++++
 2 files changed, 193 insertions(+), 2 deletions(-)

-- 
1.8.3.1

[PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Gerd Hoffmann]

From: Eric Anholt <eric@anholt.net>

The BCM2835-ARM-Peripherals.pdf documentation specifies what the
function selects do for the pins, and there are a bunch of obvious
groupings to be made.  With these created, we'll be able to replace
bcm2835-rpi.dtsi's main "set all of these pins to alt0" with
references to specific groups we want enabled.

Signed-off-by: Eric Anholt <eric@anholt.net>
---
 arch/arm/boot/dts/bcm283x.dtsi | 170 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 170 insertions(+)

diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index 4d9f3ab..acb616f 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -131,6 +131,176 @@
 
 			interrupt-controller;
 			#interrupt-cells = <2>;
+
+			/* Defines pin muxing groups according to
+			 * BCM2835-ARM-Peripherals.pdf page 102.
+			 *
+			 * While each pin can have its mux selected
+			 * for various functions individually, some
+			 * groups only make sense to switch to a
+			 * particular function together.
+			 */
+			i2c0_gpio0: i2c0_gpio0 {
+				brcm,pins = <0 1>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			i2c1_gpio2: i2c1_gpio2 {
+				brcm,pins = <2 3>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk0_gpio4: gpclk0_gpio4 {
+				brcm,pins = <4>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk1_gpio5: gpclk1_gpio5 {
+				brcm,pins = <5>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk2_gpio6: gpclk2_gpio6 {
+				brcm,pins = <6>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			spi0_gpio7: spi0_gpio7 {
+				brcm,pins = <7 8 9 10 11>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm0_gpio12: pwm0_gpio12 {
+				brcm,pins = <12>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm1_gpio13: pwm1_gpio13 {
+				brcm,pins = <13>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			uart0_gpio14: uart0_gpio14 {
+				brcm,pins = <14 15>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pcm_gpio18: pcm_gpio18 {
+				brcm,pins = <18 19 20 21>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			i2c0_gpio32: i2c0_gpio32 {
+				brcm,pins = <32 34>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			spio0_gpio35: spio0_gpio35 {
+				brcm,pins = <35 36 37 38 39>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm0_gpio40: pwm0_gpio40 {
+				brcm,pins = <40>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm1_gpio41: pwm1_gpio41 {
+				brcm,pins = <41>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk1_gpio42: gpclk1_gpio42 {
+				brcm,pins = <42>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk2_gpio43: gpclk2_gpio43 {
+				brcm,pins = <43>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk1_gpio44: gpclk1_gpio44 {
+				brcm,pins = <44>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm1_gpio45: pwm1_gpio45 {
+				brcm,pins = <45>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			i2c0_gpio44: i2c0_gpio44 {
+				brcm,pins = <44 45>;
+				brcm,function = <BCM2835_FSEL_ALT1>;
+			};
+			pcm_gpio28: pcm_gpio28 {
+				brcm,pins = <28 29 30 31>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+			uart1_gpio36: uart1_gpio36 {
+				brcm,pins = <36 37 38 39>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+			i2c1_gpio44: i2c1_gpio44 {
+				brcm,pins = <44 45>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+			/* Separate from the uart0_gpio14 group
+			 * because it conflicts with spi1_gpio16, and
+			 * people often run uart0 on the two pins
+			 * without flow contrl.
+			 */
+			uart0_ctsrts_gpio16: uart0_ctsrts_gpio16 {
+				brcm,pins = <16 17>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			i2c_slave_gpio18: i2c_slave_gpio18 {
+				brcm,pins = <18 19 20 21>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			emmc_gpio22: emmc_gpio22 {
+				brcm,pins = <22 23 24 25 26 27>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			uart0_gpio30: uart0_gpio30 {
+				brcm,pins = <30 31>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			uart0_ctsrts_gpio32: uart0_ctsrts_gpio32 {
+				brcm,pins = <32 33>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			spi1_gpio16: spi1_gpio16 {
+				brcm,pins = <16 17 18 19 20 21>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+			jtag_gpio22: jtag_gpio22 {
+				brcm,pins = <22 23 24 25 26 27>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+			spi2_gpio40: spi2_gpio40 {
+				brcm,pins = <40 41 42 43 44 45>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+			jtag_gpio4: jtag_gpio4 {
+				brcm,pins = <4 5 6 12 13>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+			uart1_gpio14: uart1_gpio14 {
+				brcm,pins = <14 15>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_ctsrts_gpio16: uart1_ctsrts_gpio16 {
+				brcm,pins = <16 17>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			pwm0_gpio18: pwm0_gpio18 {
+				brcm,pins = <18>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			pwm1_gpio19: pwm1_gpio19 {
+				brcm,pins = <19>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_gpio32: uart1_gpio32 {
+				brcm,pins = <32 33>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_ctsrts_gpio30: uart1_ctsrts_gpio30 {
+				brcm,pins = <30 31>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_gpio40: uart1_gpio40 {
+				brcm,pins = <40 41>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_ctsrts_gpio42: uart1_ctsrts_gpio42 {
+				brcm,pins = <42 43>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
 		};
 
 		uart0: serial@7e201000 {
-- 
1.8.3.1

[PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Gerd Hoffmann]

From: Eric Anholt <eric@anholt.net>

The BCM2835-ARM-Peripherals.pdf documentation specifies what the
function selects do for the pins, and there are a bunch of obvious
groupings to be made.  With these created, we'll be able to replace
bcm2835-rpi.dtsi's main "set all of these pins to alt0" with
references to specific groups we want enabled.

Signed-off-by: Eric Anholt <eric@anholt.net>
---
 arch/arm/boot/dts/bcm283x.dtsi | 170 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 170 insertions(+)

diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index 4d9f3ab..acb616f 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -131,6 +131,176 @@
 
 			interrupt-controller;
 			#interrupt-cells = <2>;
+
+			/* Defines pin muxing groups according to
+			 * BCM2835-ARM-Peripherals.pdf page 102.
+			 *
+			 * While each pin can have its mux selected
+			 * for various functions individually, some
+			 * groups only make sense to switch to a
+			 * particular function together.
+			 */
+			i2c0_gpio0: i2c0_gpio0 {
+				brcm,pins = <0 1>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			i2c1_gpio2: i2c1_gpio2 {
+				brcm,pins = <2 3>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk0_gpio4: gpclk0_gpio4 {
+				brcm,pins = <4>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk1_gpio5: gpclk1_gpio5 {
+				brcm,pins = <5>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk2_gpio6: gpclk2_gpio6 {
+				brcm,pins = <6>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			spi0_gpio7: spi0_gpio7 {
+				brcm,pins = <7 8 9 10 11>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm0_gpio12: pwm0_gpio12 {
+				brcm,pins = <12>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm1_gpio13: pwm1_gpio13 {
+				brcm,pins = <13>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			uart0_gpio14: uart0_gpio14 {
+				brcm,pins = <14 15>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pcm_gpio18: pcm_gpio18 {
+				brcm,pins = <18 19 20 21>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			i2c0_gpio32: i2c0_gpio32 {
+				brcm,pins = <32 34>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			spio0_gpio35: spio0_gpio35 {
+				brcm,pins = <35 36 37 38 39>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm0_gpio40: pwm0_gpio40 {
+				brcm,pins = <40>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm1_gpio41: pwm1_gpio41 {
+				brcm,pins = <41>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk1_gpio42: gpclk1_gpio42 {
+				brcm,pins = <42>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk2_gpio43: gpclk2_gpio43 {
+				brcm,pins = <43>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk1_gpio44: gpclk1_gpio44 {
+				brcm,pins = <44>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm1_gpio45: pwm1_gpio45 {
+				brcm,pins = <45>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			i2c0_gpio44: i2c0_gpio44 {
+				brcm,pins = <44 45>;
+				brcm,function = <BCM2835_FSEL_ALT1>;
+			};
+			pcm_gpio28: pcm_gpio28 {
+				brcm,pins = <28 29 30 31>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+			uart1_gpio36: uart1_gpio36 {
+				brcm,pins = <36 37 38 39>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+			i2c1_gpio44: i2c1_gpio44 {
+				brcm,pins = <44 45>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+			/* Separate from the uart0_gpio14 group
+			 * because it conflicts with spi1_gpio16, and
+			 * people often run uart0 on the two pins
+			 * without flow contrl.
+			 */
+			uart0_ctsrts_gpio16: uart0_ctsrts_gpio16 {
+				brcm,pins = <16 17>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			i2c_slave_gpio18: i2c_slave_gpio18 {
+				brcm,pins = <18 19 20 21>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			emmc_gpio22: emmc_gpio22 {
+				brcm,pins = <22 23 24 25 26 27>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			uart0_gpio30: uart0_gpio30 {
+				brcm,pins = <30 31>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			uart0_ctsrts_gpio32: uart0_ctsrts_gpio32 {
+				brcm,pins = <32 33>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			spi1_gpio16: spi1_gpio16 {
+				brcm,pins = <16 17 18 19 20 21>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+			jtag_gpio22: jtag_gpio22 {
+				brcm,pins = <22 23 24 25 26 27>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+			spi2_gpio40: spi2_gpio40 {
+				brcm,pins = <40 41 42 43 44 45>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+			jtag_gpio4: jtag_gpio4 {
+				brcm,pins = <4 5 6 12 13>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+			uart1_gpio14: uart1_gpio14 {
+				brcm,pins = <14 15>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_ctsrts_gpio16: uart1_ctsrts_gpio16 {
+				brcm,pins = <16 17>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			pwm0_gpio18: pwm0_gpio18 {
+				brcm,pins = <18>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			pwm1_gpio19: pwm1_gpio19 {
+				brcm,pins = <19>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_gpio32: uart1_gpio32 {
+				brcm,pins = <32 33>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_ctsrts_gpio30: uart1_ctsrts_gpio30 {
+				brcm,pins = <30 31>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_gpio40: uart1_gpio40 {
+				brcm,pins = <40 41>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_ctsrts_gpio42: uart1_ctsrts_gpio42 {
+				brcm,pins = <42 43>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
 		};
 
 		uart0: serial@7e201000 {
-- 
1.8.3.1

[PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Gerd Hoffmann]

From: Eric Anholt <eric@anholt.net>

The BCM2835-ARM-Peripherals.pdf documentation specifies what the
function selects do for the pins, and there are a bunch of obvious
groupings to be made.  With these created, we'll be able to replace
bcm2835-rpi.dtsi's main "set all of these pins to alt0" with
references to specific groups we want enabled.

Signed-off-by: Eric Anholt <eric@anholt.net>
---
 arch/arm/boot/dts/bcm283x.dtsi | 170 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 170 insertions(+)

diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index 4d9f3ab..acb616f 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -131,6 +131,176 @@
 
 			interrupt-controller;
 			#interrupt-cells = <2>;
+
+			/* Defines pin muxing groups according to
+			 * BCM2835-ARM-Peripherals.pdf page 102.
+			 *
+			 * While each pin can have its mux selected
+			 * for various functions individually, some
+			 * groups only make sense to switch to a
+			 * particular function together.
+			 */
+			i2c0_gpio0: i2c0_gpio0 {
+				brcm,pins = <0 1>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			i2c1_gpio2: i2c1_gpio2 {
+				brcm,pins = <2 3>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk0_gpio4: gpclk0_gpio4 {
+				brcm,pins = <4>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk1_gpio5: gpclk1_gpio5 {
+				brcm,pins = <5>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk2_gpio6: gpclk2_gpio6 {
+				brcm,pins = <6>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			spi0_gpio7: spi0_gpio7 {
+				brcm,pins = <7 8 9 10 11>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm0_gpio12: pwm0_gpio12 {
+				brcm,pins = <12>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm1_gpio13: pwm1_gpio13 {
+				brcm,pins = <13>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			uart0_gpio14: uart0_gpio14 {
+				brcm,pins = <14 15>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pcm_gpio18: pcm_gpio18 {
+				brcm,pins = <18 19 20 21>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			i2c0_gpio32: i2c0_gpio32 {
+				brcm,pins = <32 34>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			spio0_gpio35: spio0_gpio35 {
+				brcm,pins = <35 36 37 38 39>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm0_gpio40: pwm0_gpio40 {
+				brcm,pins = <40>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm1_gpio41: pwm1_gpio41 {
+				brcm,pins = <41>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk1_gpio42: gpclk1_gpio42 {
+				brcm,pins = <42>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk2_gpio43: gpclk2_gpio43 {
+				brcm,pins = <43>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk1_gpio44: gpclk1_gpio44 {
+				brcm,pins = <44>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm1_gpio45: pwm1_gpio45 {
+				brcm,pins = <45>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			i2c0_gpio44: i2c0_gpio44 {
+				brcm,pins = <44 45>;
+				brcm,function = <BCM2835_FSEL_ALT1>;
+			};
+			pcm_gpio28: pcm_gpio28 {
+				brcm,pins = <28 29 30 31>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+			uart1_gpio36: uart1_gpio36 {
+				brcm,pins = <36 37 38 39>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+			i2c1_gpio44: i2c1_gpio44 {
+				brcm,pins = <44 45>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+			/* Separate from the uart0_gpio14 group
+			 * because it conflicts with spi1_gpio16, and
+			 * people often run uart0 on the two pins
+			 * without flow contrl.
+			 */
+			uart0_ctsrts_gpio16: uart0_ctsrts_gpio16 {
+				brcm,pins = <16 17>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			i2c_slave_gpio18: i2c_slave_gpio18 {
+				brcm,pins = <18 19 20 21>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			emmc_gpio22: emmc_gpio22 {
+				brcm,pins = <22 23 24 25 26 27>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			uart0_gpio30: uart0_gpio30 {
+				brcm,pins = <30 31>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			uart0_ctsrts_gpio32: uart0_ctsrts_gpio32 {
+				brcm,pins = <32 33>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			spi1_gpio16: spi1_gpio16 {
+				brcm,pins = <16 17 18 19 20 21>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+			jtag_gpio22: jtag_gpio22 {
+				brcm,pins = <22 23 24 25 26 27>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+			spi2_gpio40: spi2_gpio40 {
+				brcm,pins = <40 41 42 43 44 45>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+			jtag_gpio4: jtag_gpio4 {
+				brcm,pins = <4 5 6 12 13>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+			uart1_gpio14: uart1_gpio14 {
+				brcm,pins = <14 15>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_ctsrts_gpio16: uart1_ctsrts_gpio16 {
+				brcm,pins = <16 17>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			pwm0_gpio18: pwm0_gpio18 {
+				brcm,pins = <18>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			pwm1_gpio19: pwm1_gpio19 {
+				brcm,pins = <19>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_gpio32: uart1_gpio32 {
+				brcm,pins = <32 33>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_ctsrts_gpio30: uart1_ctsrts_gpio30 {
+				brcm,pins = <30 31>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_gpio40: uart1_gpio40 {
+				brcm,pins = <40 41>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_ctsrts_gpio42: uart1_ctsrts_gpio42 {
+				brcm,pins = <42 43>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
 		};
 
 		uart0: serial at 7e201000 {
-- 
1.8.3.1

[PATCH 2/8] ARM: dts: bcm283x: Add the emmc pin group to bcm283x.dtsi.

[Gerd Hoffmann]

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
---
 arch/arm/boot/dts/bcm283x.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index acb616f..164d962 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -253,6 +253,10 @@
 				brcm,pins = <32 33>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
 			};
+			emmc_gpio48: emmc_gpio48 {
+				brcm,pins = <48 49 50 51 52 53>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
 			spi1_gpio16: spi1_gpio16 {
 				brcm,pins = <16 17 18 19 20 21>;
 				brcm,function = <BCM2835_FSEL_ALT4>;
-- 
1.8.3.1

[PATCH 2/8] ARM: dts: bcm283x: Add the emmc pin group to bcm283x.dtsi.

[Gerd Hoffmann]

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
---
 arch/arm/boot/dts/bcm283x.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index acb616f..164d962 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -253,6 +253,10 @@
 				brcm,pins = <32 33>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
 			};
+			emmc_gpio48: emmc_gpio48 {
+				brcm,pins = <48 49 50 51 52 53>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
 			spi1_gpio16: spi1_gpio16 {
 				brcm,pins = <16 17 18 19 20 21>;
 				brcm,function = <BCM2835_FSEL_ALT4>;
-- 
1.8.3.1

[PATCH 2/8] ARM: dts: bcm283x: Add the emmc pin group to bcm283x.dtsi.

[Gerd Hoffmann]

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
---
 arch/arm/boot/dts/bcm283x.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index acb616f..164d962 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -253,6 +253,10 @@
 				brcm,pins = <32 33>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
 			};
+			emmc_gpio48: emmc_gpio48 {
+				brcm,pins = <48 49 50 51 52 53>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
 			spi1_gpio16: spi1_gpio16 {
 				brcm,pins = <16 17 18 19 20 21>;
 				brcm,function = <BCM2835_FSEL_ALT4>;
-- 
1.8.3.1

[PATCH 3/8] ARM: dts: bcm283x: Add a group for mapping pins 48-53 to sdhost.

[Gerd Hoffmann]

From: Eric Anholt <eric@anholt.net>

This pin group definition comes from downstream.  We don't have a
driver for sdhost integrated yet, but they've been experimenting with
it and it sounds useful to bring over.

Signed-off-by: Eric Anholt <eric@anholt.net>
---
 arch/arm/boot/dts/bcm283x.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index 164d962..062d09db 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -212,6 +212,10 @@
 				brcm,pins = <45>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
+			sdhost_gpio48: sdhost_gpio48 {
+				brcm,pins = <48 49 50 51 52 53>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
 			i2c0_gpio44: i2c0_gpio44 {
 				brcm,pins = <44 45>;
 				brcm,function = <BCM2835_FSEL_ALT1>;
-- 
1.8.3.1

[PATCH 3/8] ARM: dts: bcm283x: Add a group for mapping pins 48-53 to sdhost.

[Gerd Hoffmann]

From: Eric Anholt <eric@anholt.net>

This pin group definition comes from downstream.  We don't have a
driver for sdhost integrated yet, but they've been experimenting with
it and it sounds useful to bring over.

Signed-off-by: Eric Anholt <eric@anholt.net>
---
 arch/arm/boot/dts/bcm283x.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index 164d962..062d09db 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -212,6 +212,10 @@
 				brcm,pins = <45>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
+			sdhost_gpio48: sdhost_gpio48 {
+				brcm,pins = <48 49 50 51 52 53>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
 			i2c0_gpio44: i2c0_gpio44 {
 				brcm,pins = <44 45>;
 				brcm,function = <BCM2835_FSEL_ALT1>;
-- 
1.8.3.1

[PATCH 3/8] ARM: dts: bcm283x: Add a group for mapping pins 48-53 to sdhost.

[Gerd Hoffmann]

From: Eric Anholt <eric@anholt.net>

This pin group definition comes from downstream.  We don't have a
driver for sdhost integrated yet, but they've been experimenting with
it and it sounds useful to bring over.

Signed-off-by: Eric Anholt <eric@anholt.net>
---
 arch/arm/boot/dts/bcm283x.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index 164d962..062d09db 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -212,6 +212,10 @@
 				brcm,pins = <45>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
+			sdhost_gpio48: sdhost_gpio48 {
+				brcm,pins = <48 49 50 51 52 53>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
 			i2c0_gpio44: i2c0_gpio44 {
 				brcm,pins = <44 45>;
 				brcm,function = <BCM2835_FSEL_ALT1>;
-- 
1.8.3.1

[PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Gerd Hoffmann]

From: Eric Anholt <eric@anholt.net>

This will be used for having EMMC (sdhci-bcm2835.c) drive the
wireless.

Signed-off-by: Eric Anholt <eric@anholt.net>
---
 arch/arm/boot/dts/bcm283x.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index 062d09db..b6b1950 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -257,6 +257,11 @@
 				brcm,pins = <32 33>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
 			};
+			emmc_gpio34: emmc_gpio34 {
+				brcm,pins = <34 35 36 37 38 39>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+				brcm,pull = <0 2 2 2 2 2>;
+			};
 			emmc_gpio48: emmc_gpio48 {
 				brcm,pins = <48 49 50 51 52 53>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
-- 
1.8.3.1

[PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Gerd Hoffmann]

From: Eric Anholt <eric-WhKQ6XTQaPysTnJN9+BGXg@public.gmane.org>

This will be used for having EMMC (sdhci-bcm2835.c) drive the
wireless.

Signed-off-by: Eric Anholt <eric-WhKQ6XTQaPysTnJN9+BGXg@public.gmane.org>
---
 arch/arm/boot/dts/bcm283x.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index 062d09db..b6b1950 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -257,6 +257,11 @@
 				brcm,pins = <32 33>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
 			};
+			emmc_gpio34: emmc_gpio34 {
+				brcm,pins = <34 35 36 37 38 39>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+				brcm,pull = <0 2 2 2 2 2>;
+			};
 			emmc_gpio48: emmc_gpio48 {
 				brcm,pins = <48 49 50 51 52 53>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
-- 
1.8.3.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Gerd Hoffmann]

From: Eric Anholt <eric@anholt.net>

This will be used for having EMMC (sdhci-bcm2835.c) drive the
wireless.

Signed-off-by: Eric Anholt <eric@anholt.net>
---
 arch/arm/boot/dts/bcm283x.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index 062d09db..b6b1950 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -257,6 +257,11 @@
 				brcm,pins = <32 33>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
 			};
+			emmc_gpio34: emmc_gpio34 {
+				brcm,pins = <34 35 36 37 38 39>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+				brcm,pull = <0 2 2 2 2 2>;
+			};
 			emmc_gpio48: emmc_gpio48 {
 				brcm,pins = <48 49 50 51 52 53>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
-- 
1.8.3.1

[PATCH 5/8] ARM: dts: bcm283x: add pinctrl group to &pwm, drop pins from &gpio

[Gerd Hoffmann]

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
---
 arch/arm/boot/dts/bcm2835-rpi.dtsi | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi
index 88bcd0c..ff62236 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@@ -38,7 +38,7 @@
 	};
 
 	alt0: alt0 {
-		brcm,pins = <0 1 2 3 4 5 7 8 9 10 11 40 45>;
+		brcm,pins = <0 1 2 3 4 5 7 8 9 10 11>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
 
@@ -68,6 +68,8 @@
 };
 
 &pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
 	status = "okay";
 };
 
-- 
1.8.3.1

[PATCH 5/8] ARM: dts: bcm283x: add pinctrl group to &pwm, drop pins from &gpio

[Gerd Hoffmann]

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
---
 arch/arm/boot/dts/bcm2835-rpi.dtsi | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi
index 88bcd0c..ff62236 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@@ -38,7 +38,7 @@
 	};
 
 	alt0: alt0 {
-		brcm,pins = <0 1 2 3 4 5 7 8 9 10 11 40 45>;
+		brcm,pins = <0 1 2 3 4 5 7 8 9 10 11>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
 
@@ -68,6 +68,8 @@
 };
 
 &pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
 	status = "okay";
 };
 
-- 
1.8.3.1

[PATCH 5/8] ARM: dts: bcm283x: add pinctrl group to &pwm, drop pins from &gpio

[Gerd Hoffmann]

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
---
 arch/arm/boot/dts/bcm2835-rpi.dtsi | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi
index 88bcd0c..ff62236 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@@ -38,7 +38,7 @@
 	};
 
 	alt0: alt0 {
-		brcm,pins = <0 1 2 3 4 5 7 8 9 10 11 40 45>;
+		brcm,pins = <0 1 2 3 4 5 7 8 9 10 11>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
 
@@ -68,6 +68,8 @@
 };
 
 &pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
 	status = "okay";
 };
 
-- 
1.8.3.1

[PATCH 6/8] ARM: dts: bcm283x: add pinctrl group to &i2c0, drop pins from &gpio

[Gerd Hoffmann]

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
---
 arch/arm/boot/dts/bcm2835-rpi.dtsi | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi
index ff62236..b936978 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@@ -38,7 +38,7 @@
 	};
 
 	alt0: alt0 {
-		brcm,pins = <0 1 2 3 4 5 7 8 9 10 11>;
+		brcm,pins = <2 3 4 5 7 8 9 10 11>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
 
@@ -49,6 +49,8 @@
 };
 
 &i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_gpio0>;
 	status = "okay";
 	clock-frequency = <100000>;
 };
-- 
1.8.3.1

[PATCH 6/8] ARM: dts: bcm283x: add pinctrl group to &i2c0, drop pins from &gpio

[Gerd Hoffmann]

Signed-off-by: Gerd Hoffmann <kraxel-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
---
 arch/arm/boot/dts/bcm2835-rpi.dtsi | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi
index ff62236..b936978 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@@ -38,7 +38,7 @@
 	};
 
 	alt0: alt0 {
-		brcm,pins = <0 1 2 3 4 5 7 8 9 10 11>;
+		brcm,pins = <2 3 4 5 7 8 9 10 11>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
 
@@ -49,6 +49,8 @@
 };
 
 &i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_gpio0>;
 	status = "okay";
 	clock-frequency = <100000>;
 };
-- 
1.8.3.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 6/8] ARM: dts: bcm283x: add pinctrl group to &i2c0, drop pins from &gpio

[Gerd Hoffmann]

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
---
 arch/arm/boot/dts/bcm2835-rpi.dtsi | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi
index ff62236..b936978 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@@ -38,7 +38,7 @@
 	};
 
 	alt0: alt0 {
-		brcm,pins = <0 1 2 3 4 5 7 8 9 10 11>;
+		brcm,pins = <2 3 4 5 7 8 9 10 11>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
 
@@ -49,6 +49,8 @@
 };
 
 &i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_gpio0>;
 	status = "okay";
 	clock-frequency = <100000>;
 };
-- 
1.8.3.1

[PATCH 7/8] ARM: dts: bcm283x: add pinctrl group to &i2c1, drop pins from &gpio

[Gerd Hoffmann]

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
---
 arch/arm/boot/dts/bcm2835-rpi.dtsi | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi
index b936978..8688204 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@@ -38,7 +38,7 @@
 	};
 
 	alt0: alt0 {
-		brcm,pins = <2 3 4 5 7 8 9 10 11>;
+		brcm,pins = <4 5 7 8 9 10 11>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
 
@@ -56,6 +56,8 @@
 };
 
 &i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_gpio2>;
 	status = "okay";
 	clock-frequency = <100000>;
 };
-- 
1.8.3.1

[PATCH 7/8] ARM: dts: bcm283x: add pinctrl group to &i2c1, drop pins from &gpio

[Gerd Hoffmann]

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
---
 arch/arm/boot/dts/bcm2835-rpi.dtsi | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi
index b936978..8688204 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@@ -38,7 +38,7 @@
 	};
 
 	alt0: alt0 {
-		brcm,pins = <2 3 4 5 7 8 9 10 11>;
+		brcm,pins = <4 5 7 8 9 10 11>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
 
@@ -56,6 +56,8 @@
 };
 
 &i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_gpio2>;
 	status = "okay";
 	clock-frequency = <100000>;
 };
-- 
1.8.3.1

[PATCH 7/8] ARM: dts: bcm283x: add pinctrl group to &i2c1, drop pins from &gpio

[Gerd Hoffmann]

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
---
 arch/arm/boot/dts/bcm2835-rpi.dtsi | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi
index b936978..8688204 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@@ -38,7 +38,7 @@
 	};
 
 	alt0: alt0 {
-		brcm,pins = <2 3 4 5 7 8 9 10 11>;
+		brcm,pins = <4 5 7 8 9 10 11>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
 
@@ -56,6 +56,8 @@
 };
 
 &i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_gpio2>;
 	status = "okay";
 	clock-frequency = <100000>;
 };
-- 
1.8.3.1

[PATCH 8/8] ARM: dts: bcm283x: add pinctrl group to &sdhci, drop pins from &gpio

[Gerd Hoffmann]

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
---
 arch/arm/boot/dts/bcm2835-rpi.dtsi | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi
index 8688204..3f0ce61 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@@ -43,7 +43,7 @@
 	};
 
 	alt3: alt3 {
-		brcm,pins = <48 49 50 51 52 53>;
+		brcm,pins = <>;
 		brcm,function = <BCM2835_FSEL_ALT3>;
 	};
 };
@@ -67,6 +67,8 @@
 };
 
 &sdhci {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio48>;
 	status = "okay";
 	bus-width = <4>;
 };
-- 
1.8.3.1

[PATCH 8/8] ARM: dts: bcm283x: add pinctrl group to &sdhci, drop pins from &gpio

[Gerd Hoffmann]

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
---
 arch/arm/boot/dts/bcm2835-rpi.dtsi | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi
index 8688204..3f0ce61 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@@ -43,7 +43,7 @@
 	};
 
 	alt3: alt3 {
-		brcm,pins = <48 49 50 51 52 53>;
+		brcm,pins = <>;
 		brcm,function = <BCM2835_FSEL_ALT3>;
 	};
 };
@@ -67,6 +67,8 @@
 };
 
 &sdhci {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio48>;
 	status = "okay";
 	bus-width = <4>;
 };
-- 
1.8.3.1

[PATCH 8/8] ARM: dts: bcm283x: add pinctrl group to &sdhci, drop pins from &gpio

[Gerd Hoffmann]

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
---
 arch/arm/boot/dts/bcm2835-rpi.dtsi | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi
index 8688204..3f0ce61 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@@ -43,7 +43,7 @@
 	};
 
 	alt3: alt3 {
-		brcm,pins = <48 49 50 51 52 53>;
+		brcm,pins = <>;
 		brcm,function = <BCM2835_FSEL_ALT3>;
 	};
 };
@@ -67,6 +67,8 @@
 };
 
 &sdhci {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio48>;
 	status = "okay";
 	bus-width = <4>;
 };
-- 
1.8.3.1

Re: [PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Stefan Wahren]

Hi Gerd,

> Gerd Hoffmann <kraxel@redhat.com> hat am 7. September 2016 um 12:31
> geschrieben:
> 
> 
> From: Eric Anholt <eric@anholt.net>
> 
> The BCM2835-ARM-Peripherals.pdf documentation specifies what the
> function selects do for the pins, and there are a bunch of obvious
> groupings to be made.  With these created, we'll be able to replace
> bcm2835-rpi.dtsi's main "set all of these pins to alt0" with
> references to specific groups we want enabled.

on IMX/MXS platform it's unwanted to add all possible muxes in the dtsi file. So
i would suggest to add only the actually used muxes. That makes it easier to
maintain.

Regards
Stefan

Re: [PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Stefan Wahren]

Hi Gerd,

> Gerd Hoffmann <kraxel-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> hat am 7. September 2016 um 12:31
> geschrieben:
> 
> 
> From: Eric Anholt <eric-WhKQ6XTQaPysTnJN9+BGXg@public.gmane.org>
> 
> The BCM2835-ARM-Peripherals.pdf documentation specifies what the
> function selects do for the pins, and there are a bunch of obvious
> groupings to be made.  With these created, we'll be able to replace
> bcm2835-rpi.dtsi's main "set all of these pins to alt0" with
> references to specific groups we want enabled.

on IMX/MXS platform it's unwanted to add all possible muxes in the dtsi file. So
i would suggest to add only the actually used muxes. That makes it easier to
maintain.

Regards
Stefan
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Stefan Wahren]

Hi Gerd,

> Gerd Hoffmann <kraxel@redhat.com> hat am 7. September 2016 um 12:31
> geschrieben:
> 
> 
> From: Eric Anholt <eric@anholt.net>
> 
> The BCM2835-ARM-Peripherals.pdf documentation specifies what the
> function selects do for the pins, and there are a bunch of obvious
> groupings to be made.  With these created, we'll be able to replace
> bcm2835-rpi.dtsi's main "set all of these pins to alt0" with
> references to specific groups we want enabled.

on IMX/MXS platform it's unwanted to add all possible muxes in the dtsi file. So
i would suggest to add only the actually used muxes. That makes it easier to
maintain.

Regards
Stefan

Re: [PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Stefan Wahren]

> Gerd Hoffmann <kraxel@redhat.com> hat am 7. September 2016 um 12:31
> geschrieben:
> 
> 
> From: Eric Anholt <eric@anholt.net>
> 
> This will be used for having EMMC (sdhci-bcm2835.c) drive the
> wireless.

sdhci-bcm2835.c has been replaced by sdhci-iproc.c

> 
> Signed-off-by: Eric Anholt <eric@anholt.net>
> ---
>  arch/arm/boot/dts/bcm283x.dtsi | 5 +++++
>  1 file changed, 5 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
> index 062d09db..b6b1950 100644
> --- a/arch/arm/boot/dts/bcm283x.dtsi
> +++ b/arch/arm/boot/dts/bcm283x.dtsi
> @@ -257,6 +257,11 @@
>  				brcm,pins = <32 33>;
>  				brcm,function = <BCM2835_FSEL_ALT3>;
>  			};
> +			emmc_gpio34: emmc_gpio34 {
> +				brcm,pins = <34 35 36 37 38 39>;
> +				brcm,function = <BCM2835_FSEL_ALT3>;
> +				brcm,pull = <0 2 2 2 2 2>;

How about adding pull defines to include/dt-bindings/pinctrl/bcm2835.h?

> +			};
>  			emmc_gpio48: emmc_gpio48 {
>  				brcm,pins = <48 49 50 51 52 53>;
>  				brcm,function = <BCM2835_FSEL_ALT3>;
> -- 
> 1.8.3.1
> 
> 
> _______________________________________________
> linux-rpi-kernel mailing list
> linux-rpi-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-rpi-kernel

[PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Stefan Wahren]

> Gerd Hoffmann <kraxel@redhat.com> hat am 7. September 2016 um 12:31
> geschrieben:
> 
> 
> From: Eric Anholt <eric@anholt.net>
> 
> This will be used for having EMMC (sdhci-bcm2835.c) drive the
> wireless.

sdhci-bcm2835.c has been replaced by sdhci-iproc.c

> 
> Signed-off-by: Eric Anholt <eric@anholt.net>
> ---
>  arch/arm/boot/dts/bcm283x.dtsi | 5 +++++
>  1 file changed, 5 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
> index 062d09db..b6b1950 100644
> --- a/arch/arm/boot/dts/bcm283x.dtsi
> +++ b/arch/arm/boot/dts/bcm283x.dtsi
> @@ -257,6 +257,11 @@
>  				brcm,pins = <32 33>;
>  				brcm,function = <BCM2835_FSEL_ALT3>;
>  			};
> +			emmc_gpio34: emmc_gpio34 {
> +				brcm,pins = <34 35 36 37 38 39>;
> +				brcm,function = <BCM2835_FSEL_ALT3>;
> +				brcm,pull = <0 2 2 2 2 2>;

How about adding pull defines to include/dt-bindings/pinctrl/bcm2835.h?

> +			};
>  			emmc_gpio48: emmc_gpio48 {
>  				brcm,pins = <48 49 50 51 52 53>;
>  				brcm,function = <BCM2835_FSEL_ALT3>;
> -- 
> 1.8.3.1
> 
> 
> _______________________________________________
> linux-rpi-kernel mailing list
> linux-rpi-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-rpi-kernel

Re: [PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Eric Anholt]

[-- Attachment #1: Type: text/plain, Size: 1093 bytes --]

Stefan Wahren <stefan.wahren@i2se.com> writes:

> Hi Gerd,
>
>> Gerd Hoffmann <kraxel@redhat.com> hat am 7. September 2016 um 12:31
>> geschrieben:
>> 
>> 
>> From: Eric Anholt <eric@anholt.net>
>> 
>> The BCM2835-ARM-Peripherals.pdf documentation specifies what the
>> function selects do for the pins, and there are a bunch of obvious
>> groupings to be made.  With these created, we'll be able to replace
>> bcm2835-rpi.dtsi's main "set all of these pins to alt0" with
>> references to specific groups we want enabled.
>
> on IMX/MXS platform it's unwanted to add all possible muxes in the dtsi file. So
> i would suggest to add only the actually used muxes. That makes it easier to
> maintain.

On the other hand, I find that having to go back to the docs for
determining the fsels is worse than just verifying and defining them
here all at once.  Maintaining has also gotten harder because our DTs
are split across 32 and 64-bit ARM, so rpi3 changes that require adding
one of these pinmux definitions back to the dtsi would require painful
cross-branch merges.

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 800 bytes --]

[PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Eric Anholt]

Stefan Wahren <stefan.wahren@i2se.com> writes:

> Hi Gerd,
>
>> Gerd Hoffmann <kraxel@redhat.com> hat am 7. September 2016 um 12:31
>> geschrieben:
>> 
>> 
>> From: Eric Anholt <eric@anholt.net>
>> 
>> The BCM2835-ARM-Peripherals.pdf documentation specifies what the
>> function selects do for the pins, and there are a bunch of obvious
>> groupings to be made.  With these created, we'll be able to replace
>> bcm2835-rpi.dtsi's main "set all of these pins to alt0" with
>> references to specific groups we want enabled.
>
> on IMX/MXS platform it's unwanted to add all possible muxes in the dtsi file. So
> i would suggest to add only the actually used muxes. That makes it easier to
> maintain.

On the other hand, I find that having to go back to the docs for
determining the fsels is worse than just verifying and defining them
here all at once.  Maintaining has also gotten harder because our DTs
are split across 32 and 64-bit ARM, so rpi3 changes that require adding
one of these pinmux definitions back to the dtsi would require painful
cross-branch merges.
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 800 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160907/2dd24ff4/attachment.sig>

Re: [PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Gerd Hoffmann]

On Mi, 2016-09-07 at 20:13 +0200, Stefan Wahren wrote:
> > Gerd Hoffmann <kraxel@redhat.com> hat am 7. September 2016 um 12:31
> > geschrieben:
> > 
> > 
> > From: Eric Anholt <eric@anholt.net>
> > 
> > This will be used for having EMMC (sdhci-bcm2835.c) drive the
> > wireless.
> 
> sdhci-bcm2835.c has been replaced by sdhci-iproc.c

Ah, right, I'll update the commit msg for v2.

> How about adding pull defines to include/dt-bindings/pinctrl/bcm2835.h?

Already there (or do you mean something other than '#define
BCM2835_FSEL_*' ?)

cheers,
  Gerd

[PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Gerd Hoffmann]

On Mi, 2016-09-07 at 20:13 +0200, Stefan Wahren wrote:
> > Gerd Hoffmann <kraxel@redhat.com> hat am 7. September 2016 um 12:31
> > geschrieben:
> > 
> > 
> > From: Eric Anholt <eric@anholt.net>
> > 
> > This will be used for having EMMC (sdhci-bcm2835.c) drive the
> > wireless.
> 
> sdhci-bcm2835.c has been replaced by sdhci-iproc.c

Ah, right, I'll update the commit msg for v2.

> How about adding pull defines to include/dt-bindings/pinctrl/bcm2835.h?

Already there (or do you mean something other than '#define
BCM2835_FSEL_*' ?)

cheers,
  Gerd

Re: [PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Gerd Hoffmann]

On Mi, 2016-09-07 at 11:50 -0700, Eric Anholt wrote:
> Stefan Wahren <stefan.wahren@i2se.com> writes:
> 
> > Hi Gerd,
> >
> >> Gerd Hoffmann <kraxel@redhat.com> hat am 7. September 2016 um 12:31
> >> geschrieben:
> >> 
> >> 
> >> From: Eric Anholt <eric@anholt.net>
> >> 
> >> The BCM2835-ARM-Peripherals.pdf documentation specifies what the
> >> function selects do for the pins, and there are a bunch of obvious
> >> groupings to be made.  With these created, we'll be able to replace
> >> bcm2835-rpi.dtsi's main "set all of these pins to alt0" with
> >> references to specific groups we want enabled.
> >
> > on IMX/MXS platform it's unwanted to add all possible muxes in the dtsi file. So
> > i would suggest to add only the actually used muxes. That makes it easier to
> > maintain.
> 
> On the other hand, I find that having to go back to the docs for
> determining the fsels is worse than just verifying and defining them
> here all at once.

Agreeing here.  IMO it is nice to have them all even if unused for
documentation purposes.

> Maintaining has also gotten harder because our DTs
> are split across 32 and 64-bit ARM, so rpi3 changes that require adding
> one of these pinmux definitions back to the dtsi would require painful
> cross-branch merges.

It'll also easily cause merge conflicts.

cheers,
  Gerd

Re: [PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Gerd Hoffmann]

On Mi, 2016-09-07 at 11:50 -0700, Eric Anholt wrote:
> Stefan Wahren <stefan.wahren-eS4NqCHxEME@public.gmane.org> writes:
> 
> > Hi Gerd,
> >
> >> Gerd Hoffmann <kraxel-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> hat am 7. September 2016 um 12:31
> >> geschrieben:
> >> 
> >> 
> >> From: Eric Anholt <eric-WhKQ6XTQaPysTnJN9+BGXg@public.gmane.org>
> >> 
> >> The BCM2835-ARM-Peripherals.pdf documentation specifies what the
> >> function selects do for the pins, and there are a bunch of obvious
> >> groupings to be made.  With these created, we'll be able to replace
> >> bcm2835-rpi.dtsi's main "set all of these pins to alt0" with
> >> references to specific groups we want enabled.
> >
> > on IMX/MXS platform it's unwanted to add all possible muxes in the dtsi file. So
> > i would suggest to add only the actually used muxes. That makes it easier to
> > maintain.
> 
> On the other hand, I find that having to go back to the docs for
> determining the fsels is worse than just verifying and defining them
> here all at once.

Agreeing here.  IMO it is nice to have them all even if unused for
documentation purposes.

> Maintaining has also gotten harder because our DTs
> are split across 32 and 64-bit ARM, so rpi3 changes that require adding
> one of these pinmux definitions back to the dtsi would require painful
> cross-branch merges.

It'll also easily cause merge conflicts.

cheers,
  Gerd

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Gerd Hoffmann]

On Mi, 2016-09-07 at 11:50 -0700, Eric Anholt wrote:
> Stefan Wahren <stefan.wahren@i2se.com> writes:
> 
> > Hi Gerd,
> >
> >> Gerd Hoffmann <kraxel@redhat.com> hat am 7. September 2016 um 12:31
> >> geschrieben:
> >> 
> >> 
> >> From: Eric Anholt <eric@anholt.net>
> >> 
> >> The BCM2835-ARM-Peripherals.pdf documentation specifies what the
> >> function selects do for the pins, and there are a bunch of obvious
> >> groupings to be made.  With these created, we'll be able to replace
> >> bcm2835-rpi.dtsi's main "set all of these pins to alt0" with
> >> references to specific groups we want enabled.
> >
> > on IMX/MXS platform it's unwanted to add all possible muxes in the dtsi file. So
> > i would suggest to add only the actually used muxes. That makes it easier to
> > maintain.
> 
> On the other hand, I find that having to go back to the docs for
> determining the fsels is worse than just verifying and defining them
> here all at once.

Agreeing here.  IMO it is nice to have them all even if unused for
documentation purposes.

> Maintaining has also gotten harder because our DTs
> are split across 32 and 64-bit ARM, so rpi3 changes that require adding
> one of these pinmux definitions back to the dtsi would require painful
> cross-branch merges.

It'll also easily cause merge conflicts.

cheers,
  Gerd

Re: [PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Stefan Wahren]

Am 08.09.2016 um 09:44 schrieb Gerd Hoffmann:
> On Mi, 2016-09-07 at 20:13 +0200, Stefan Wahren wrote:
>>> Gerd Hoffmann <kraxel@redhat.com> hat am 7. September 2016 um 12:31
>>> geschrieben:
>>>
>>>
>>> From: Eric Anholt <eric@anholt.net>
>>>
>>> This will be used for having EMMC (sdhci-bcm2835.c) drive the
>>> wireless.
>> sdhci-bcm2835.c has been replaced by sdhci-iproc.c
> Ah, right, I'll update the commit msg for v2.
>
>> How about adding pull defines to include/dt-bindings/pinctrl/bcm2835.h?
> Already there (or do you mean something other than '#define
> BCM2835_FSEL_*' ?)

No, i thought of the GPIO pull up/down register values:

BCM2835_PUD_OFF 0
BCM2835_PUD_DOWN 1
BCM2835_PUD_UP 2

>
> cheers,
>   Gerd
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Stefan Wahren]

Am 08.09.2016 um 09:44 schrieb Gerd Hoffmann:
> On Mi, 2016-09-07 at 20:13 +0200, Stefan Wahren wrote:
>>> Gerd Hoffmann <kraxel@redhat.com> hat am 7. September 2016 um 12:31
>>> geschrieben:
>>>
>>>
>>> From: Eric Anholt <eric@anholt.net>
>>>
>>> This will be used for having EMMC (sdhci-bcm2835.c) drive the
>>> wireless.
>> sdhci-bcm2835.c has been replaced by sdhci-iproc.c
> Ah, right, I'll update the commit msg for v2.
>
>> How about adding pull defines to include/dt-bindings/pinctrl/bcm2835.h?
> Already there (or do you mean something other than '#define
> BCM2835_FSEL_*' ?)

No, i thought of the GPIO pull up/down register values:

BCM2835_PUD_OFF 0
BCM2835_PUD_DOWN 1
BCM2835_PUD_UP 2

>
> cheers,
>   Gerd
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Stefan Wahren]

Hi Gerd,

> Gerd Hoffmann <kraxel@redhat.com> hat am 7. September 2016 um 12:31
> geschrieben:
> 
> 
> From: Eric Anholt <eric@anholt.net>
> 
> The BCM2835-ARM-Peripherals.pdf documentation specifies what the
> function selects do for the pins, and there are a bunch of obvious
> groupings to be made.  With these created, we'll be able to replace
> bcm2835-rpi.dtsi's main "set all of these pins to alt0" with
> references to specific groups we want enabled.
> 
> Signed-off-by: Eric Anholt <eric@anholt.net>
> ---
>  arch/arm/boot/dts/bcm283x.dtsi | 170
> +++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 170 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
> index 4d9f3ab..acb616f 100644
> --- a/arch/arm/boot/dts/bcm283x.dtsi
> +++ b/arch/arm/boot/dts/bcm283x.dtsi
> @@ -131,6 +131,176 @@
>  
>  			interrupt-controller;
>  			#interrupt-cells = <2>;
> +
> +			/* Defines pin muxing groups according to
> +			 * BCM2835-ARM-Peripherals.pdf page 102.
> +			 *
> +			 * While each pin can have its mux selected
> +			 * for various functions individually, some
> +			 * groups only make sense to switch to a
> +			 * particular function together.
> +			 */
> ...
> +			i2c0_gpio32: i2c0_gpio32 {
> +				brcm,pins = <32 34>;
> +				brcm,function = <BCM2835_FSEL_ALT0>;
> +			};
> +			spio0_gpio35: spio0_gpio35 {
> +				brcm,pins = <35 36 37 38 39>;
> +				brcm,function = <BCM2835_FSEL_ALT0>;
> +			};

s/spio0/spi0

> +			pwm0_gpio40: pwm0_gpio40 {
> +				brcm,pins = <40>;
> +				brcm,function = <BCM2835_FSEL_ALT0>;
> +			};
> ...
> +			uart1_ctsrts_gpio42: uart1_ctsrts_gpio42 {
> +				brcm,pins = <42 43>;
> +				brcm,function = <BCM2835_FSEL_ALT5>;
> +			};

Please sort all pinctrl nodes by label.

According to this page [1] the pinctrl group for parallel display interface is
missing. Is it intended?

[1] - http://elinux.org/RPi_BCM2835_GPIOs

>  		};
>  
>  		uart0: serial@7e201000 {
> -- 
> 1.8.3.1
> 
> 
> _______________________________________________
> linux-rpi-kernel mailing list
> linux-rpi-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-rpi-kernel

Re: [PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Stefan Wahren]

Hi Gerd,

> Gerd Hoffmann <kraxel-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> hat am 7. September 2016 um 12:31
> geschrieben:
> 
> 
> From: Eric Anholt <eric-WhKQ6XTQaPysTnJN9+BGXg@public.gmane.org>
> 
> The BCM2835-ARM-Peripherals.pdf documentation specifies what the
> function selects do for the pins, and there are a bunch of obvious
> groupings to be made.  With these created, we'll be able to replace
> bcm2835-rpi.dtsi's main "set all of these pins to alt0" with
> references to specific groups we want enabled.
> 
> Signed-off-by: Eric Anholt <eric-WhKQ6XTQaPysTnJN9+BGXg@public.gmane.org>
> ---
>  arch/arm/boot/dts/bcm283x.dtsi | 170
> +++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 170 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
> index 4d9f3ab..acb616f 100644
> --- a/arch/arm/boot/dts/bcm283x.dtsi
> +++ b/arch/arm/boot/dts/bcm283x.dtsi
> @@ -131,6 +131,176 @@
>  
>  			interrupt-controller;
>  			#interrupt-cells = <2>;
> +
> +			/* Defines pin muxing groups according to
> +			 * BCM2835-ARM-Peripherals.pdf page 102.
> +			 *
> +			 * While each pin can have its mux selected
> +			 * for various functions individually, some
> +			 * groups only make sense to switch to a
> +			 * particular function together.
> +			 */
> ...
> +			i2c0_gpio32: i2c0_gpio32 {
> +				brcm,pins = <32 34>;
> +				brcm,function = <BCM2835_FSEL_ALT0>;
> +			};
> +			spio0_gpio35: spio0_gpio35 {
> +				brcm,pins = <35 36 37 38 39>;
> +				brcm,function = <BCM2835_FSEL_ALT0>;
> +			};

s/spio0/spi0

> +			pwm0_gpio40: pwm0_gpio40 {
> +				brcm,pins = <40>;
> +				brcm,function = <BCM2835_FSEL_ALT0>;
> +			};
> ...
> +			uart1_ctsrts_gpio42: uart1_ctsrts_gpio42 {
> +				brcm,pins = <42 43>;
> +				brcm,function = <BCM2835_FSEL_ALT5>;
> +			};

Please sort all pinctrl nodes by label.

According to this page [1] the pinctrl group for parallel display interface is
missing. Is it intended?

[1] - http://elinux.org/RPi_BCM2835_GPIOs

>  		};
>  
>  		uart0: serial@7e201000 {
> -- 
> 1.8.3.1
> 
> 
> _______________________________________________
> linux-rpi-kernel mailing list
> linux-rpi-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
> http://lists.infradead.org/mailman/listinfo/linux-rpi-kernel
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Stefan Wahren]

Hi Gerd,

> Gerd Hoffmann <kraxel@redhat.com> hat am 7. September 2016 um 12:31
> geschrieben:
> 
> 
> From: Eric Anholt <eric@anholt.net>
> 
> The BCM2835-ARM-Peripherals.pdf documentation specifies what the
> function selects do for the pins, and there are a bunch of obvious
> groupings to be made.  With these created, we'll be able to replace
> bcm2835-rpi.dtsi's main "set all of these pins to alt0" with
> references to specific groups we want enabled.
> 
> Signed-off-by: Eric Anholt <eric@anholt.net>
> ---
>  arch/arm/boot/dts/bcm283x.dtsi | 170
> +++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 170 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
> index 4d9f3ab..acb616f 100644
> --- a/arch/arm/boot/dts/bcm283x.dtsi
> +++ b/arch/arm/boot/dts/bcm283x.dtsi
> @@ -131,6 +131,176 @@
>  
>  			interrupt-controller;
>  			#interrupt-cells = <2>;
> +
> +			/* Defines pin muxing groups according to
> +			 * BCM2835-ARM-Peripherals.pdf page 102.
> +			 *
> +			 * While each pin can have its mux selected
> +			 * for various functions individually, some
> +			 * groups only make sense to switch to a
> +			 * particular function together.
> +			 */
> ...
> +			i2c0_gpio32: i2c0_gpio32 {
> +				brcm,pins = <32 34>;
> +				brcm,function = <BCM2835_FSEL_ALT0>;
> +			};
> +			spio0_gpio35: spio0_gpio35 {
> +				brcm,pins = <35 36 37 38 39>;
> +				brcm,function = <BCM2835_FSEL_ALT0>;
> +			};

s/spio0/spi0

> +			pwm0_gpio40: pwm0_gpio40 {
> +				brcm,pins = <40>;
> +				brcm,function = <BCM2835_FSEL_ALT0>;
> +			};
> ...
> +			uart1_ctsrts_gpio42: uart1_ctsrts_gpio42 {
> +				brcm,pins = <42 43>;
> +				brcm,function = <BCM2835_FSEL_ALT5>;
> +			};

Please sort all pinctrl nodes by label.

According to this page [1] the pinctrl group for parallel display interface is
missing. Is it intended?

[1] - http://elinux.org/RPi_BCM2835_GPIOs

>  		};
>  
>  		uart0: serial at 7e201000 {
> -- 
> 1.8.3.1
> 
> 
> _______________________________________________
> linux-rpi-kernel mailing list
> linux-rpi-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-rpi-kernel

Re: [PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Scott Branden]

Hi Gerd/Eric

On 16-09-08 12:44 AM, Gerd Hoffmann wrote:
> On Mi, 2016-09-07 at 20:13 +0200, Stefan Wahren wrote:
>>> Gerd Hoffmann <kraxel@redhat.com> hat am 7. September 2016 um 12:31
>>> geschrieben:
>>>
>>>
>>> From: Eric Anholt <eric@anholt.net>
>>>
>>> This will be used for having EMMC (sdhci-bcm2835.c) drive the
>>> wireless.
>>
>> sdhci-bcm2835.c has been replaced by sdhci-iproc.c
>
> Ah, right, I'll update the commit msg for v2.
>
Should we entirely remove sdhci-bcm2835.c to reduce confusion going forward?

>> How about adding pull defines to include/dt-bindings/pinctrl/bcm2835.h?
>
> Already there (or do you mean something other than '#define
> BCM2835_FSEL_*' ?)
>
> cheers,
>   Gerd
>

Thanks,
  Scott

Re: [PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Scott Branden]

Hi Gerd/Eric

On 16-09-08 12:44 AM, Gerd Hoffmann wrote:
> On Mi, 2016-09-07 at 20:13 +0200, Stefan Wahren wrote:
>>> Gerd Hoffmann <kraxel-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> hat am 7. September 2016 um 12:31
>>> geschrieben:
>>>
>>>
>>> From: Eric Anholt <eric-WhKQ6XTQaPysTnJN9+BGXg@public.gmane.org>
>>>
>>> This will be used for having EMMC (sdhci-bcm2835.c) drive the
>>> wireless.
>>
>> sdhci-bcm2835.c has been replaced by sdhci-iproc.c
>
> Ah, right, I'll update the commit msg for v2.
>
Should we entirely remove sdhci-bcm2835.c to reduce confusion going forward?

>> How about adding pull defines to include/dt-bindings/pinctrl/bcm2835.h?
>
> Already there (or do you mean something other than '#define
> BCM2835_FSEL_*' ?)
>
> cheers,
>   Gerd
>

Thanks,
  Scott
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Scott Branden]

Hi Gerd/Eric

On 16-09-08 12:44 AM, Gerd Hoffmann wrote:
> On Mi, 2016-09-07 at 20:13 +0200, Stefan Wahren wrote:
>>> Gerd Hoffmann <kraxel@redhat.com> hat am 7. September 2016 um 12:31
>>> geschrieben:
>>>
>>>
>>> From: Eric Anholt <eric@anholt.net>
>>>
>>> This will be used for having EMMC (sdhci-bcm2835.c) drive the
>>> wireless.
>>
>> sdhci-bcm2835.c has been replaced by sdhci-iproc.c
>
> Ah, right, I'll update the commit msg for v2.
>
Should we entirely remove sdhci-bcm2835.c to reduce confusion going forward?

>> How about adding pull defines to include/dt-bindings/pinctrl/bcm2835.h?
>
> Already there (or do you mean something other than '#define
> BCM2835_FSEL_*' ?)
>
> cheers,
>   Gerd
>

Thanks,
  Scott

Re: [PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Stefan Wahren]

Hi Scott,

Am 08.09.2016 um 21:50 schrieb Scott Branden:
> Hi Gerd/Eric
>
> On 16-09-08 12:44 AM, Gerd Hoffmann wrote:
>> On Mi, 2016-09-07 at 20:13 +0200, Stefan Wahren wrote:
>>>> Gerd Hoffmann <kraxel@redhat.com> hat am 7. September 2016 um 12:31
>>>> geschrieben:
>>>>
>>>>
>>>> From: Eric Anholt <eric@anholt.net>
>>>>
>>>> This will be used for having EMMC (sdhci-bcm2835.c) drive the
>>>> wireless.
>>>
>>> sdhci-bcm2835.c has been replaced by sdhci-iproc.c
>>
>> Ah, right, I'll update the commit msg for v2.
>>
> Should we entirely remove sdhci-bcm2835.c to reduce confusion going
> forward?

did i missed something?

https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=46cd175c9788e39a1c57698ab58f34844d216428

https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=7eb16493ecaa41ceeb448717ee2c59690cd9047f


>
>>> How about adding pull defines to include/dt-bindings/pinctrl/bcm2835.h?
>>
>> Already there (or do you mean something other than '#define
>> BCM2835_FSEL_*' ?)
>>
>> cheers,
>>   Gerd
>>
>
> Thanks,
>  Scott

Re: [PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Stefan Wahren]

Hi Scott,

Am 08.09.2016 um 21:50 schrieb Scott Branden:
> Hi Gerd/Eric
>
> On 16-09-08 12:44 AM, Gerd Hoffmann wrote:
>> On Mi, 2016-09-07 at 20:13 +0200, Stefan Wahren wrote:
>>>> Gerd Hoffmann <kraxel-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> hat am 7. September 2016 um 12:31
>>>> geschrieben:
>>>>
>>>>
>>>> From: Eric Anholt <eric-WhKQ6XTQaPysTnJN9+BGXg@public.gmane.org>
>>>>
>>>> This will be used for having EMMC (sdhci-bcm2835.c) drive the
>>>> wireless.
>>>
>>> sdhci-bcm2835.c has been replaced by sdhci-iproc.c
>>
>> Ah, right, I'll update the commit msg for v2.
>>
> Should we entirely remove sdhci-bcm2835.c to reduce confusion going
> forward?

did i missed something?

https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=46cd175c9788e39a1c57698ab58f34844d216428

https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=7eb16493ecaa41ceeb448717ee2c59690cd9047f


>
>>> How about adding pull defines to include/dt-bindings/pinctrl/bcm2835.h?
>>
>> Already there (or do you mean something other than '#define
>> BCM2835_FSEL_*' ?)
>>
>> cheers,
>>   Gerd
>>
>
> Thanks,
>  Scott

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Stefan Wahren]

Hi Scott,

Am 08.09.2016 um 21:50 schrieb Scott Branden:
> Hi Gerd/Eric
>
> On 16-09-08 12:44 AM, Gerd Hoffmann wrote:
>> On Mi, 2016-09-07 at 20:13 +0200, Stefan Wahren wrote:
>>>> Gerd Hoffmann <kraxel@redhat.com> hat am 7. September 2016 um 12:31
>>>> geschrieben:
>>>>
>>>>
>>>> From: Eric Anholt <eric@anholt.net>
>>>>
>>>> This will be used for having EMMC (sdhci-bcm2835.c) drive the
>>>> wireless.
>>>
>>> sdhci-bcm2835.c has been replaced by sdhci-iproc.c
>>
>> Ah, right, I'll update the commit msg for v2.
>>
> Should we entirely remove sdhci-bcm2835.c to reduce confusion going
> forward?

did i missed something?

https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=46cd175c9788e39a1c57698ab58f34844d216428

https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=7eb16493ecaa41ceeb448717ee2c59690cd9047f


>
>>> How about adding pull defines to include/dt-bindings/pinctrl/bcm2835.h?
>>
>> Already there (or do you mean something other than '#define
>> BCM2835_FSEL_*' ?)
>>
>> cheers,
>>   Gerd
>>
>
> Thanks,
>  Scott

Re: [PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Gerd Hoffmann]

  Hi,

> No, i thought of the GPIO pull up/down register values:
> 
> BCM2835_PUD_OFF 0
> BCM2835_PUD_DOWN 1
> BCM2835_PUD_UP 2

We can do that, sure (and probably drop the unused "enum
bcm2835_pinconf_pull" from drivers/pinctrl/bcm/pinctrl-bcm2835.c at the
same time).

But I fail to see how this is related to the patch discussed, looks like
a independent issue to me ...

cheers,
  Gerd

[PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Gerd Hoffmann]

  Hi,

> No, i thought of the GPIO pull up/down register values:
> 
> BCM2835_PUD_OFF 0
> BCM2835_PUD_DOWN 1
> BCM2835_PUD_UP 2

We can do that, sure (and probably drop the unused "enum
bcm2835_pinconf_pull" from drivers/pinctrl/bcm/pinctrl-bcm2835.c at the
same time).

But I fail to see how this is related to the patch discussed, looks like
a independent issue to me ...

cheers,
  Gerd

Re: [PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Gerd Hoffmann]

On Fr, 2016-09-09 at 10:26 +0200, Gerd Hoffmann wrote:
>   Hi,
> 
> > No, i thought of the GPIO pull up/down register values:
> > 
> > BCM2835_PUD_OFF 0
> > BCM2835_PUD_DOWN 1
> > BCM2835_PUD_UP 2
> 
> We can do that, sure (and probably drop the unused "enum
> bcm2835_pinconf_pull" from drivers/pinctrl/bcm/pinctrl-bcm2835.c at the
> same time).
> 
> But I fail to see how this is related to the patch discussed, looks like
> a independent issue to me ...

Oops, noticed that emmc_gpio34 uses them while ordering all the entries.

cheers,
  Gerd

Re: [PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Gerd Hoffmann]

On Fr, 2016-09-09 at 10:26 +0200, Gerd Hoffmann wrote:
>   Hi,
> 
> > No, i thought of the GPIO pull up/down register values:
> > 
> > BCM2835_PUD_OFF 0
> > BCM2835_PUD_DOWN 1
> > BCM2835_PUD_UP 2
> 
> We can do that, sure (and probably drop the unused "enum
> bcm2835_pinconf_pull" from drivers/pinctrl/bcm/pinctrl-bcm2835.c at the
> same time).
> 
> But I fail to see how this is related to the patch discussed, looks like
> a independent issue to me ...

Oops, noticed that emmc_gpio34 uses them while ordering all the entries.

cheers,
  Gerd

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Gerd Hoffmann]

On Fr, 2016-09-09 at 10:26 +0200, Gerd Hoffmann wrote:
>   Hi,
> 
> > No, i thought of the GPIO pull up/down register values:
> > 
> > BCM2835_PUD_OFF 0
> > BCM2835_PUD_DOWN 1
> > BCM2835_PUD_UP 2
> 
> We can do that, sure (and probably drop the unused "enum
> bcm2835_pinconf_pull" from drivers/pinctrl/bcm/pinctrl-bcm2835.c at the
> same time).
> 
> But I fail to see how this is related to the patch discussed, looks like
> a independent issue to me ...

Oops, noticed that emmc_gpio34 uses them while ordering all the entries.

cheers,
  Gerd

Re: [PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Gerd Hoffmann]

  Hi,

> According to this page [1] the pinctrl group for parallel display interface is
> missing. Is it intended?
> 
> [1] - http://elinux.org/RPi_BCM2835_GPIOs

Just an oversight I guess.  Eric?

Does this look correct?

+                       dpi_gpio4: dpi_gpio4 {
+                               brcm,pins = <4 5 6 7 8 9 10 11 12 13
+                                            14 15 16 17 18 19 20 21
+                                            22 23 24 25 26 27>;
+                               brcm,function = <BCM2835_FSEL_ALT2>;
+                       };

thanks,
  Gerd

Re: [PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Gerd Hoffmann]

  Hi,

> According to this page [1] the pinctrl group for parallel display interface is
> missing. Is it intended?
> 
> [1] - http://elinux.org/RPi_BCM2835_GPIOs

Just an oversight I guess.  Eric?

Does this look correct?

+                       dpi_gpio4: dpi_gpio4 {
+                               brcm,pins = <4 5 6 7 8 9 10 11 12 13
+                                            14 15 16 17 18 19 20 21
+                                            22 23 24 25 26 27>;
+                               brcm,function = <BCM2835_FSEL_ALT2>;
+                       };

thanks,
  Gerd

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Gerd Hoffmann]

  Hi,

> According to this page [1] the pinctrl group for parallel display interface is
> missing. Is it intended?
> 
> [1] - http://elinux.org/RPi_BCM2835_GPIOs

Just an oversight I guess.  Eric?

Does this look correct?

+                       dpi_gpio4: dpi_gpio4 {
+                               brcm,pins = <4 5 6 7 8 9 10 11 12 13
+                                            14 15 16 17 18 19 20 21
+                                            22 23 24 25 26 27>;
+                               brcm,function = <BCM2835_FSEL_ALT2>;
+                       };

thanks,
  Gerd

Re: [PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Stefan Wahren]

Am 09.09.2016 um 11:05 schrieb Gerd Hoffmann:
>   Hi,
>
>> According to this page [1] the pinctrl group for parallel display interface is
>> missing. Is it intended?
>>
>> [1] - http://elinux.org/RPi_BCM2835_GPIOs
> Just an oversight I guess.  Eric?
>
> Does this look correct?
>
> +                       dpi_gpio4: dpi_gpio4 {
> +                               brcm,pins = <4 5 6 7 8 9 10 11 12 13
> +                                            14 15 16 17 18 19 20 21
> +                                            22 23 24 25 26 27>;
> +                               brcm,function = <BCM2835_FSEL_ALT2>;
> +                       };

According to the wiki and the website [1] it starts at gpio 0

[1] -
https://www.raspberrypi.org/documentation/hardware/raspberrypi/dpi/README.md

>
> thanks,
>   Gerd
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Stefan Wahren]

Am 09.09.2016 um 11:05 schrieb Gerd Hoffmann:
>   Hi,
>
>> According to this page [1] the pinctrl group for parallel display interface is
>> missing. Is it intended?
>>
>> [1] - http://elinux.org/RPi_BCM2835_GPIOs
> Just an oversight I guess.  Eric?
>
> Does this look correct?
>
> +                       dpi_gpio4: dpi_gpio4 {
> +                               brcm,pins = <4 5 6 7 8 9 10 11 12 13
> +                                            14 15 16 17 18 19 20 21
> +                                            22 23 24 25 26 27>;
> +                               brcm,function = <BCM2835_FSEL_ALT2>;
> +                       };

According to the wiki and the website [1] it starts at gpio 0

[1] -
https://www.raspberrypi.org/documentation/hardware/raspberrypi/dpi/README.md

>
> thanks,
>   Gerd
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Stefan Wahren]

Am 09.09.2016 um 11:05 schrieb Gerd Hoffmann:
>   Hi,
>
>> According to this page [1] the pinctrl group for parallel display interface is
>> missing. Is it intended?
>>
>> [1] - http://elinux.org/RPi_BCM2835_GPIOs
> Just an oversight I guess.  Eric?
>
> Does this look correct?
>
> +                       dpi_gpio4: dpi_gpio4 {
> +                               brcm,pins = <4 5 6 7 8 9 10 11 12 13
> +                                            14 15 16 17 18 19 20 21
> +                                            22 23 24 25 26 27>;
> +                               brcm,function = <BCM2835_FSEL_ALT2>;
> +                       };

According to the wiki and the website [1] it starts at gpio 0

[1] -
https://www.raspberrypi.org/documentation/hardware/raspberrypi/dpi/README.md

>
> thanks,
>   Gerd
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Scott Branden]

Hi Stefan,

On 16-09-08 11:58 PM, Stefan Wahren wrote:
> Hi Scott,
>
> Am 08.09.2016 um 21:50 schrieb Scott Branden:
>> Hi Gerd/Eric
>>
>> On 16-09-08 12:44 AM, Gerd Hoffmann wrote:
>>> On Mi, 2016-09-07 at 20:13 +0200, Stefan Wahren wrote:
>>>>> Gerd Hoffmann <kraxel@redhat.com> hat am 7. September 2016 um 12:31
>>>>> geschrieben:
>>>>>
>>>>>
>>>>> From: Eric Anholt <eric@anholt.net>
>>>>>
>>>>> This will be used for having EMMC (sdhci-bcm2835.c) drive the
>>>>> wireless.
>>>>
>>>> sdhci-bcm2835.c has been replaced by sdhci-iproc.c
>>>
>>> Ah, right, I'll update the commit msg for v2.
>>>
>> Should we entirely remove sdhci-bcm2835.c to reduce confusion going
>> forward?
>
> did i missed something?
No - looks like I did.  Everything is cleaned up in latest.
>
> https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=46cd175c9788e39a1c57698ab58f34844d216428
>
> https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=7eb16493ecaa41ceeb448717ee2c59690cd9047f
>
>
>>
>>>> How about adding pull defines to include/dt-bindings/pinctrl/bcm2835.h?
>>>
>>> Already there (or do you mean something other than '#define
>>> BCM2835_FSEL_*' ?)
>>>
>>> cheers,
>>>   Gerd
>>>
>>
>> Thanks,
>>  Scott
>

Re: [PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Scott Branden]

Hi Stefan,

On 16-09-08 11:58 PM, Stefan Wahren wrote:
> Hi Scott,
>
> Am 08.09.2016 um 21:50 schrieb Scott Branden:
>> Hi Gerd/Eric
>>
>> On 16-09-08 12:44 AM, Gerd Hoffmann wrote:
>>> On Mi, 2016-09-07 at 20:13 +0200, Stefan Wahren wrote:
>>>>> Gerd Hoffmann <kraxel-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> hat am 7. September 2016 um 12:31
>>>>> geschrieben:
>>>>>
>>>>>
>>>>> From: Eric Anholt <eric-WhKQ6XTQaPysTnJN9+BGXg@public.gmane.org>
>>>>>
>>>>> This will be used for having EMMC (sdhci-bcm2835.c) drive the
>>>>> wireless.
>>>>
>>>> sdhci-bcm2835.c has been replaced by sdhci-iproc.c
>>>
>>> Ah, right, I'll update the commit msg for v2.
>>>
>> Should we entirely remove sdhci-bcm2835.c to reduce confusion going
>> forward?
>
> did i missed something?
No - looks like I did.  Everything is cleaned up in latest.
>
> https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=46cd175c9788e39a1c57698ab58f34844d216428
>
> https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=7eb16493ecaa41ceeb448717ee2c59690cd9047f
>
>
>>
>>>> How about adding pull defines to include/dt-bindings/pinctrl/bcm2835.h?
>>>
>>> Already there (or do you mean something other than '#define
>>> BCM2835_FSEL_*' ?)
>>>
>>> cheers,
>>>   Gerd
>>>
>>
>> Thanks,
>>  Scott
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Scott Branden]

Hi Stefan,

On 16-09-08 11:58 PM, Stefan Wahren wrote:
> Hi Scott,
>
> Am 08.09.2016 um 21:50 schrieb Scott Branden:
>> Hi Gerd/Eric
>>
>> On 16-09-08 12:44 AM, Gerd Hoffmann wrote:
>>> On Mi, 2016-09-07 at 20:13 +0200, Stefan Wahren wrote:
>>>>> Gerd Hoffmann <kraxel@redhat.com> hat am 7. September 2016 um 12:31
>>>>> geschrieben:
>>>>>
>>>>>
>>>>> From: Eric Anholt <eric@anholt.net>
>>>>>
>>>>> This will be used for having EMMC (sdhci-bcm2835.c) drive the
>>>>> wireless.
>>>>
>>>> sdhci-bcm2835.c has been replaced by sdhci-iproc.c
>>>
>>> Ah, right, I'll update the commit msg for v2.
>>>
>> Should we entirely remove sdhci-bcm2835.c to reduce confusion going
>> forward?
>
> did i missed something?
No - looks like I did.  Everything is cleaned up in latest.
>
> https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=46cd175c9788e39a1c57698ab58f34844d216428
>
> https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=7eb16493ecaa41ceeb448717ee2c59690cd9047f
>
>
>>
>>>> How about adding pull defines to include/dt-bindings/pinctrl/bcm2835.h?
>>>
>>> Already there (or do you mean something other than '#define
>>> BCM2835_FSEL_*' ?)
>>>
>>> cheers,
>>>   Gerd
>>>
>>
>> Thanks,
>>  Scott
>

Re: [PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Eric Anholt]

e<#secure method=pgpmime mode=sign>
Gerd Hoffmann <kraxel@redhat.com> writes:

>   Hi,
>
>> According to this page [1] the pinctrl group for parallel display interface is
>> missing. Is it intended?
>> 
>> [1] - http://elinux.org/RPi_BCM2835_GPIOs
>
> Just an oversight I guess.  Eric?
>
> Does this look correct?
>
> +                       dpi_gpio4: dpi_gpio4 {
> +                               brcm,pins = <4 5 6 7 8 9 10 11 12 13
> +                                            14 15 16 17 18 19 20 21
> +                                            22 23 24 25 26 27>;
> +                               brcm,function = <BCM2835_FSEL_ALT2>;
> +                       };

For DPI, you also need pins 0-3 in there for clock and syncs.

That set of data pins would be for a 24-bit mode, which is what we
should be using for the Adafruit kippah + 7" panel combo.

Re: [PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Eric Anholt]

e<#secure method=pgpmime mode=sign>
Gerd Hoffmann <kraxel-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> writes:

>   Hi,
>
>> According to this page [1] the pinctrl group for parallel display interface is
>> missing. Is it intended?
>> 
>> [1] - http://elinux.org/RPi_BCM2835_GPIOs
>
> Just an oversight I guess.  Eric?
>
> Does this look correct?
>
> +                       dpi_gpio4: dpi_gpio4 {
> +                               brcm,pins = <4 5 6 7 8 9 10 11 12 13
> +                                            14 15 16 17 18 19 20 21
> +                                            22 23 24 25 26 27>;
> +                               brcm,function = <BCM2835_FSEL_ALT2>;
> +                       };

For DPI, you also need pins 0-3 in there for clock and syncs.

That set of data pins would be for a 24-bit mode, which is what we
should be using for the Adafruit kippah + 7" panel combo.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Eric Anholt]

e<#secure method=pgpmime mode=sign>
Gerd Hoffmann <kraxel@redhat.com> writes:

>   Hi,
>
>> According to this page [1] the pinctrl group for parallel display interface is
>> missing. Is it intended?
>> 
>> [1] - http://elinux.org/RPi_BCM2835_GPIOs
>
> Just an oversight I guess.  Eric?
>
> Does this look correct?
>
> +                       dpi_gpio4: dpi_gpio4 {
> +                               brcm,pins = <4 5 6 7 8 9 10 11 12 13
> +                                            14 15 16 17 18 19 20 21
> +                                            22 23 24 25 26 27>;
> +                               brcm,function = <BCM2835_FSEL_ALT2>;
> +                       };

For DPI, you also need pins 0-3 in there for clock and syncs.

That set of data pins would be for a 24-bit mode, which is what we
should be using for the Adafruit kippah + 7" panel combo.

Re: [PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Eric Anholt]

[-- Attachment #1: Type: text/plain, Size: 1099 bytes --]

Stefan Wahren <stefan.wahren@i2se.com> writes:

>> Gerd Hoffmann <kraxel@redhat.com> hat am 7. September 2016 um 12:31
>> geschrieben:
>> 
>> 
>> From: Eric Anholt <eric@anholt.net>
>> 
>> This will be used for having EMMC (sdhci-bcm2835.c) drive the
>> wireless.
>
> sdhci-bcm2835.c has been replaced by sdhci-iproc.c
>
>> 
>> Signed-off-by: Eric Anholt <eric@anholt.net>
>> ---
>>  arch/arm/boot/dts/bcm283x.dtsi | 5 +++++
>>  1 file changed, 5 insertions(+)
>> 
>> diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
>> index 062d09db..b6b1950 100644
>> --- a/arch/arm/boot/dts/bcm283x.dtsi
>> +++ b/arch/arm/boot/dts/bcm283x.dtsi
>> @@ -257,6 +257,11 @@
>>  				brcm,pins = <32 33>;
>>  				brcm,function = <BCM2835_FSEL_ALT3>;
>>  			};
>> +			emmc_gpio34: emmc_gpio34 {
>> +				brcm,pins = <34 35 36 37 38 39>;
>> +				brcm,function = <BCM2835_FSEL_ALT3>;
>> +				brcm,pull = <0 2 2 2 2 2>;
>
> How about adding pull defines to include/dt-bindings/pinctrl/bcm2835.h?

A fine idea, but it should not be a requirement for this series.

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 800 bytes --]

[PATCH 4/8] ARM: dts: bcm283x: Add a new EMMC pin group from the downstream tree.

[Eric Anholt]

Stefan Wahren <stefan.wahren@i2se.com> writes:

>> Gerd Hoffmann <kraxel@redhat.com> hat am 7. September 2016 um 12:31
>> geschrieben:
>> 
>> 
>> From: Eric Anholt <eric@anholt.net>
>> 
>> This will be used for having EMMC (sdhci-bcm2835.c) drive the
>> wireless.
>
> sdhci-bcm2835.c has been replaced by sdhci-iproc.c
>
>> 
>> Signed-off-by: Eric Anholt <eric@anholt.net>
>> ---
>>  arch/arm/boot/dts/bcm283x.dtsi | 5 +++++
>>  1 file changed, 5 insertions(+)
>> 
>> diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
>> index 062d09db..b6b1950 100644
>> --- a/arch/arm/boot/dts/bcm283x.dtsi
>> +++ b/arch/arm/boot/dts/bcm283x.dtsi
>> @@ -257,6 +257,11 @@
>>  				brcm,pins = <32 33>;
>>  				brcm,function = <BCM2835_FSEL_ALT3>;
>>  			};
>> +			emmc_gpio34: emmc_gpio34 {
>> +				brcm,pins = <34 35 36 37 38 39>;
>> +				brcm,function = <BCM2835_FSEL_ALT3>;
>> +				brcm,pull = <0 2 2 2 2 2>;
>
> How about adding pull defines to include/dt-bindings/pinctrl/bcm2835.h?

A fine idea, but it should not be a requirement for this series.
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 800 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160909/e05f5ac4/attachment.sig>

Re: [PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Dave Stevenson]

On 09/09/16 22:20, Eric Anholt wrote:
> e<#secure method=pgpmime mode=sign>
> Gerd Hoffmann <kraxel@redhat.com> writes:
>
>>    Hi,
>>
>>> According to this page [1] the pinctrl group for parallel display interface is
>>> missing. Is it intended?
>>>
>>> [1] - http://elinux.org/RPi_BCM2835_GPIOs
>> Just an oversight I guess.  Eric?
>>
>> Does this look correct?
>>
>> +                       dpi_gpio4: dpi_gpio4 {
>> +                               brcm,pins = <4 5 6 7 8 9 10 11 12 13
>> +                                            14 15 16 17 18 19 20 21
>> +                                            22 23 24 25 26 27>;
>> +                               brcm,function = <BCM2835_FSEL_ALT2>;
>> +                       };
> For DPI, you also need pins 0-3 in there for clock and syncs.
>
> That set of data pins would be for a 24-bit mode, which is what we
> should be using for the Adafruit kippah + 7" panel combo.
The Kippah is only 18bit, RGB666.
https://www.adafruit.com/products/2454
"The pins used are GPIO 2 through 21 inclusive. That means you don't get 
the UART RX/TX pins (no console cable) and you don't get the standard 
user I2C pins, the EEPROM I2C pins, or hardware SPI pins. You do get to 
use pins #22, #23, #24, #25, #26 and #27, and the USB ports are fine to 
use too."

On the forum there are some that report they have used DPI in RGB888, 
but they're not using the Kippah. I had mentioned this to Phil E that 
there should be a dpi18 overlay, but not got around to sorting that.

>
> _______________________________________________
> linux-rpi-kernel mailing list
> linux-rpi-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-rpi-kernel
>

[PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Dave Stevenson]

On 09/09/16 22:20, Eric Anholt wrote:
> e<#secure method=pgpmime mode=sign>
> Gerd Hoffmann <kraxel@redhat.com> writes:
>
>>    Hi,
>>
>>> According to this page [1] the pinctrl group for parallel display interface is
>>> missing. Is it intended?
>>>
>>> [1] - http://elinux.org/RPi_BCM2835_GPIOs
>> Just an oversight I guess.  Eric?
>>
>> Does this look correct?
>>
>> +                       dpi_gpio4: dpi_gpio4 {
>> +                               brcm,pins = <4 5 6 7 8 9 10 11 12 13
>> +                                            14 15 16 17 18 19 20 21
>> +                                            22 23 24 25 26 27>;
>> +                               brcm,function = <BCM2835_FSEL_ALT2>;
>> +                       };
> For DPI, you also need pins 0-3 in there for clock and syncs.
>
> That set of data pins would be for a 24-bit mode, which is what we
> should be using for the Adafruit kippah + 7" panel combo.
The Kippah is only 18bit, RGB666.
https://www.adafruit.com/products/2454
"The pins used are GPIO 2 through 21 inclusive. That means you don't get 
the UART RX/TX pins (no console cable) and you don't get the standard 
user I2C pins, the EEPROM I2C pins, or hardware SPI pins. You do get to 
use pins #22, #23, #24, #25, #26 and #27, and the USB ports are fine to 
use too."

On the forum there are some that report they have used DPI in RGB888, 
but they're not using the Kippah. I had mentioned this to Phil E that 
there should be a dpi18 overlay, but not got around to sorting that.

>
> _______________________________________________
> linux-rpi-kernel mailing list
> linux-rpi-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-rpi-kernel
>

Re: [PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Eric Anholt]

[-- Attachment #1: Type: text/plain, Size: 1622 bytes --]

Dave Stevenson <linux-rpi-kernel@destevenson.freeserve.co.uk> writes:

> On 09/09/16 22:20, Eric Anholt wrote:
>> e<#secure method=pgpmime mode=sign>
>> Gerd Hoffmann <kraxel@redhat.com> writes:
>>
>>>    Hi,
>>>
>>>> According to this page [1] the pinctrl group for parallel display interface is
>>>> missing. Is it intended?
>>>>
>>>> [1] - http://elinux.org/RPi_BCM2835_GPIOs
>>> Just an oversight I guess.  Eric?
>>>
>>> Does this look correct?
>>>
>>> +                       dpi_gpio4: dpi_gpio4 {
>>> +                               brcm,pins = <4 5 6 7 8 9 10 11 12 13
>>> +                                            14 15 16 17 18 19 20 21
>>> +                                            22 23 24 25 26 27>;
>>> +                               brcm,function = <BCM2835_FSEL_ALT2>;
>>> +                       };
>> For DPI, you also need pins 0-3 in there for clock and syncs.
>>
>> That set of data pins would be for a 24-bit mode, which is what we
>> should be using for the Adafruit kippah + 7" panel combo.
> The Kippah is only 18bit, RGB666.
> https://www.adafruit.com/products/2454
> "The pins used are GPIO 2 through 21 inclusive. That means you don't get 
> the UART RX/TX pins (no console cable) and you don't get the standard 
> user I2C pins, the EEPROM I2C pins, or hardware SPI pins. You do get to 
> use pins #22, #23, #24, #25, #26 and #27, and the USB ports are fine to 
> use too."

I was confused because my pinctrl was set up for 18, but the panel
driver for it is set up for 24.  It looks like 18 is right, so I should
probably correct the panel driver.

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 800 bytes --]

[PATCH 1/8] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Eric Anholt]

Dave Stevenson <linux-rpi-kernel@destevenson.freeserve.co.uk> writes:

> On 09/09/16 22:20, Eric Anholt wrote:
>> e<#secure method=pgpmime mode=sign>
>> Gerd Hoffmann <kraxel@redhat.com> writes:
>>
>>>    Hi,
>>>
>>>> According to this page [1] the pinctrl group for parallel display interface is
>>>> missing. Is it intended?
>>>>
>>>> [1] - http://elinux.org/RPi_BCM2835_GPIOs
>>> Just an oversight I guess.  Eric?
>>>
>>> Does this look correct?
>>>
>>> +                       dpi_gpio4: dpi_gpio4 {
>>> +                               brcm,pins = <4 5 6 7 8 9 10 11 12 13
>>> +                                            14 15 16 17 18 19 20 21
>>> +                                            22 23 24 25 26 27>;
>>> +                               brcm,function = <BCM2835_FSEL_ALT2>;
>>> +                       };
>> For DPI, you also need pins 0-3 in there for clock and syncs.
>>
>> That set of data pins would be for a 24-bit mode, which is what we
>> should be using for the Adafruit kippah + 7" panel combo.
> The Kippah is only 18bit, RGB666.
> https://www.adafruit.com/products/2454
> "The pins used are GPIO 2 through 21 inclusive. That means you don't get 
> the UART RX/TX pins (no console cable) and you don't get the standard 
> user I2C pins, the EEPROM I2C pins, or hardware SPI pins. You do get to 
> use pins #22, #23, #24, #25, #26 and #27, and the USB ports are fine to 
> use too."

I was confused because my pinctrl was set up for 18, but the panel
driver for it is set up for 24.  It looks like 18 is right, so I should
probably correct the panel driver.
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 800 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160912/a143f3d2/attachment.sig>