* [U-Boot] [PATCH v1 0/2] ARM: dts: at91: add dts files for the boards of SAMA5D4
@ 2016-10-26 9:03 Wenyou Yang
2016-10-26 9:03 ` [U-Boot] [PATCH v1 1/2] ARM: dts: at91: add dts file for sama5d4 Xplained board Wenyou Yang
2016-10-26 9:03 ` [U-Boot] [PATCH v1 2/2] ARM: dts: at91: add dts file for sama5d4ek board Wenyou Yang
0 siblings, 2 replies; 3+ messages in thread
From: Wenyou Yang @ 2016-10-26 9:03 UTC (permalink / raw)
To: u-boot
The purpose of the patchset is add the dts files for boards,
sama5d4 Xplained board and sama5d4ek board.
Wenyou Yang (2):
ARM: dts: at91: add dts file for sama5d4 Xplained board
ARM: dts: at91: add dts file for sama5d4ek board
arch/arm/dts/Makefile | 6 +
arch/arm/dts/at91-sama5d4_xplained.dts | 285 +++++
arch/arm/dts/at91-sama5d4ek.dts | 340 ++++++
arch/arm/dts/sama5d4.dtsi | 1910 ++++++++++++++++++++++++++++++++
4 files changed, 2541 insertions(+)
create mode 100644 arch/arm/dts/at91-sama5d4_xplained.dts
create mode 100644 arch/arm/dts/at91-sama5d4ek.dts
create mode 100644 arch/arm/dts/sama5d4.dtsi
--
2.7.4
^ permalink raw reply [flat|nested] 3+ messages in thread
* [U-Boot] [PATCH v1 1/2] ARM: dts: at91: add dts file for sama5d4 Xplained board
2016-10-26 9:03 [U-Boot] [PATCH v1 0/2] ARM: dts: at91: add dts files for the boards of SAMA5D4 Wenyou Yang
@ 2016-10-26 9:03 ` Wenyou Yang
2016-10-26 9:03 ` [U-Boot] [PATCH v1 2/2] ARM: dts: at91: add dts file for sama5d4ek board Wenyou Yang
1 sibling, 0 replies; 3+ messages in thread
From: Wenyou Yang @ 2016-10-26 9:03 UTC (permalink / raw)
To: u-boot
The dts file is copied from the kernel, do the following changes.
- add reg property for pinctrl node.
- move the gpio (pioA, pioB, pioC ...) nodes from the pinctrl
child's nodes to its slibling nodes.
- add pinctrl node for the cs pin of spi0.
- fix the compile warning.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
---
arch/arm/dts/Makefile | 3 +
arch/arm/dts/at91-sama5d4_xplained.dts | 285 +++++
arch/arm/dts/sama5d4.dtsi | 1910 ++++++++++++++++++++++++++++++++
3 files changed, 2198 insertions(+)
create mode 100644 arch/arm/dts/at91-sama5d4_xplained.dts
create mode 100644 arch/arm/dts/sama5d4.dtsi
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 8458f6b..8992636 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -294,6 +294,9 @@ dtb-$(CONFIG_SOC_KEYSTONE) += k2hk-evm.dtb \
dtb-$(CONFIG_TARGET_SAMA5D2_XPLAINED) += \
at91-sama5d2_xplained.dtb
+dtb-$(CONFIG_TARGET_SAMA5D4_XPLAINED) += \
+ at91-sama5d4_xplained.dtb
+
targets += $(dtb-y)
# Add any required device tree compiler flags here
diff --git a/arch/arm/dts/at91-sama5d4_xplained.dts b/arch/arm/dts/at91-sama5d4_xplained.dts
new file mode 100644
index 0000000..196a803
--- /dev/null
+++ b/arch/arm/dts/at91-sama5d4_xplained.dts
@@ -0,0 +1,285 @@
+/*
+ * at91-sama5d4_xplained.dts - Device Tree file for SAMA5D4 Xplained board
+ *
+ * Copyright (C) 2015 Atmel,
+ * 2015 Josh Wu <josh.wu@atmel.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+#include "sama5d4.dtsi"
+
+/ {
+ model = "Atmel SAMA5D4 Xplained";
+ compatible = "atmel,sama5d4-xplained", "atmel,sama5d4", "atmel,sama5";
+
+ aliases {
+ spi0 = &spi0;
+ };
+
+ chosen {
+ stdout-path = &usart3;
+ };
+
+ memory {
+ reg = <0x20000000 0x20000000>;
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <12000000>;
+ };
+ };
+
+ ahb {
+ apb {
+ spi0: spi at f8010000 {
+ cs-gpios = <&pioC 3 0>, <0>, <0>, <0>;
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi0 &pinctrl_spi0_cs>;
+ m25p80 at 0 {
+ compatible = "atmel,at25df321a";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ };
+ };
+
+ i2c0: i2c at f8014000 {
+ status = "okay";
+ };
+
+ macb0: ethernet at f8020000 {
+ phy-mode = "rmii";
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_macb0_rmii &pinctrl_macb0_phy_irq>;
+
+ phy0: ethernet-phy at 1 {
+ interrupt-parent = <&pioE>;
+ interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+ reg = <1>;
+ };
+ };
+
+ mmc1: mmc at fc000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
+ vmmc-supply = <&vcc_mmc1_reg>;
+ vqmmc-supply = <&vcc_3v3_reg>;
+ status = "okay";
+ slot at 0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioE 3 0>;
+ };
+ };
+
+ usart3: serial at fc00c000 {
+ status = "okay";
+ };
+
+ usart4: serial at fc010000 {
+ status = "okay";
+ };
+
+ spi1: spi at fc018000 {
+ cs-gpios = <&pioB 21 0>;
+ status = "okay";
+ };
+
+ adc0: adc at fc034000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ /* external trigger conflicts with USBA_VBUS */
+ &pinctrl_adc0_ad0
+ &pinctrl_adc0_ad1
+ &pinctrl_adc0_ad2
+ &pinctrl_adc0_ad3
+ &pinctrl_adc0_ad4
+ >;
+ atmel,adc-vref = <3300>;
+ status = "okay";
+ };
+
+ watchdog at fc068640 {
+ status = "okay";
+ };
+
+ pinctrl at fc06a000 {
+ board {
+ pinctrl_mmc1_cd: mmc1_cd {
+ atmel,pins =
+ <AT91_PIOE 3 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
+ pinctrl_usba_vbus: usba_vbus {
+ atmel,pins =
+ <AT91_PIOE 31 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+ };
+ pinctrl_key_gpio: key_gpio_0 {
+ atmel,pins =
+ <AT91_PIOE 8 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
+ pinctrl_macb0_phy_irq: macb0_phy_irq_0 {
+ atmel,pins =
+ <AT91_PIOE 1 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
+ pinctrl_spi0_cs: spi0_cs {
+ atmel,pins =
+ <AT91_PIOC 3 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(1))>;
+ };
+ };
+ };
+ };
+
+ usb0: gadget at 00400000 {
+ atmel,vbus-gpio = <&pioE 31 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ status = "okay";
+ };
+
+ usb1: ohci at 00500000 {
+ num-ports = <3>;
+ atmel,vbus-gpio = <0
+ &pioE 11 GPIO_ACTIVE_HIGH
+ &pioE 14 GPIO_ACTIVE_HIGH
+ >;
+ status = "okay";
+ };
+
+ usb2: ehci at 00600000 {
+ status = "okay";
+ };
+
+ nand0: nand at 80000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ nand-on-flash-bbt;
+ atmel,has-pmecc;
+ status = "okay";
+
+ at91bootstrap at 0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ bootloader at 40000 {
+ label = "bootloader";
+ reg = <0x40000 0x80000>;
+ };
+
+ bootloaderenv at c0000 {
+ label = "bootloader env";
+ reg = <0xc0000 0xc0000>;
+ };
+
+ dtb at 180000 {
+ label = "device tree";
+ reg = <0x180000 0x80000>;
+ };
+
+ kernel at 200000 {
+ label = "kernel";
+ reg = <0x200000 0x600000>;
+ };
+
+ rootfs at 800000 {
+ label = "rootfs";
+ reg = <0x800000 0x0f800000>;
+ };
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_key_gpio>;
+
+ pb_user1 {
+ label = "pb_user1";
+ gpios = <&pioE 8 GPIO_ACTIVE_HIGH>;
+ linux,code = <0x100>;
+ wakeup-source;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ status = "okay";
+
+ d8 {
+ label = "d8";
+ gpios = <&pioD 30 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ d10 {
+ label = "d10";
+ gpios = <&pioE 15 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ vcc_3v3_reg: fixedregulator at 0 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC 3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ reg = <0 1>;
+ };
+
+ vcc_mmc1_reg: fixedregulator at 1 {
+ compatible = "regulator-fixed";
+ gpio = <&pioE 4 GPIO_ACTIVE_LOW>;
+ regulator-name = "VDD MCI1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_3v3_reg>;
+ regulator-always-on;
+ reg = <1 1>;
+ };
+};
diff --git a/arch/arm/dts/sama5d4.dtsi b/arch/arm/dts/sama5d4.dtsi
new file mode 100644
index 0000000..b0169ef
--- /dev/null
+++ b/arch/arm/dts/sama5d4.dtsi
@@ -0,0 +1,1910 @@
+/*
+ * sama5d4.dtsi - Device Tree Include file for SAMA5D4 family SoC
+ *
+ * Copyright (C) 2014 Atmel,
+ * 2014 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "skeleton.dtsi"
+#include <dt-bindings/clock/at91.h>
+#include <dt-bindings/dma/at91.h>
+#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Atmel SAMA5D4 family SoC";
+ compatible = "atmel,sama5d4";
+ interrupt-parent = <&aic>;
+
+ aliases {
+ serial0 = &usart3;
+ serial1 = &usart4;
+ serial2 = &usart2;
+ serial3 = &usart0;
+ serial4 = &usart1;
+ serial5 = &uart0;
+ serial6 = &uart1;
+ gpio0 = &pioA;
+ gpio1 = &pioB;
+ gpio2 = &pioC;
+ gpio3 = &pioD;
+ gpio4 = &pioE;
+ pwm0 = &pwm0;
+ ssc0 = &ssc0;
+ ssc1 = &ssc1;
+ tcb0 = &tcb0;
+ tcb1 = &tcb1;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
+ };
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu at 0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a5";
+ reg = <0>;
+ next-level-cache = <&L2>;
+ };
+ };
+
+ memory {
+ reg = <0x20000000 0x20000000>;
+ };
+
+ clocks {
+ slow_xtal: slow_xtal {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ };
+
+ main_xtal: main_xtal {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ };
+
+ adc_op_clk: adc_op_clk{
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <1000000>;
+ };
+ };
+
+ ns_sram: sram at 00210000 {
+ compatible = "mmio-sram";
+ reg = <0x00210000 0x10000>;
+ };
+
+ ahb {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ usb0: gadget at 00400000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "atmel,sama5d3-udc";
+ reg = <0x00400000 0x100000
+ 0xfc02c000 0x4000>;
+ interrupts = <47 IRQ_TYPE_LEVEL_HIGH 2>;
+ clocks = <&udphs_clk>, <&utmi>;
+ clock-names = "pclk", "hclk";
+ status = "disabled";
+
+ ep0: endpoint at 0 {
+ reg = <0>;
+ atmel,fifo-size = <64>;
+ atmel,nb-banks = <1>;
+ };
+
+ ep1: endpoint at 1 {
+ reg = <1>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <3>;
+ atmel,can-dma;
+ atmel,can-isoc;
+ };
+
+ ep2: endpoint at 2 {
+ reg = <2>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <3>;
+ atmel,can-dma;
+ atmel,can-isoc;
+ };
+
+ ep3: endpoint at 3 {
+ reg = <3>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ atmel,can-dma;
+ atmel,can-isoc;
+ };
+
+ ep4: endpoint at 4 {
+ reg = <4>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ atmel,can-dma;
+ atmel,can-isoc;
+ };
+
+ ep5: endpoint at 5 {
+ reg = <5>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ atmel,can-dma;
+ atmel,can-isoc;
+ };
+
+ ep6: endpoint at 6 {
+ reg = <6>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ atmel,can-dma;
+ atmel,can-isoc;
+ };
+
+ ep7: endpoint at 7 {
+ reg = <7>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ atmel,can-dma;
+ atmel,can-isoc;
+ };
+
+ ep8: endpoint at 8 {
+ reg = <8>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ atmel,can-isoc;
+ };
+
+ ep9: endpoint at 9 {
+ reg = <9>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ atmel,can-isoc;
+ };
+
+ ep10: endpoint at 10 {
+ reg = <10>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ atmel,can-isoc;
+ };
+
+ ep11: endpoint at 11 {
+ reg = <11>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ atmel,can-isoc;
+ };
+
+ ep12: endpoint at 12 {
+ reg = <12>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ atmel,can-isoc;
+ };
+
+ ep13: endpoint at 13 {
+ reg = <13>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ atmel,can-isoc;
+ };
+
+ ep14: endpoint at 14 {
+ reg = <14>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ atmel,can-isoc;
+ };
+
+ ep15: endpoint at 15 {
+ reg = <15>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ atmel,can-isoc;
+ };
+ };
+
+ usb1: ohci at 00500000 {
+ compatible = "atmel,at91rm9200-ohci", "usb-ohci";
+ reg = <0x00500000 0x100000>;
+ interrupts = <46 IRQ_TYPE_LEVEL_HIGH 2>;
+ clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
+ clock-names = "ohci_clk", "hclk", "uhpck";
+ status = "disabled";
+ };
+
+ usb2: ehci at 00600000 {
+ compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
+ reg = <0x00600000 0x100000>;
+ interrupts = <46 IRQ_TYPE_LEVEL_HIGH 2>;
+ clocks = <&utmi>, <&uhphs_clk>;
+ clock-names = "usb_clk", "ehci_clk";
+ status = "disabled";
+ };
+
+ L2: cache-controller at 00a00000 {
+ compatible = "arm,pl310-cache";
+ reg = <0x00a00000 0x1000>;
+ interrupts = <67 IRQ_TYPE_LEVEL_HIGH 4>;
+ cache-unified;
+ cache-level = <2>;
+ };
+
+ nand0: nand at 80000000 {
+ compatible = "atmel,sama5d4-nand", "atmel,at91rm9200-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ reg = < 0x80000000 0x08000000 /* EBI CS3 */
+ 0xfc05c070 0x00000490 /* SMC PMECC regs */
+ 0xfc05c500 0x00000100 /* SMC PMECC Error Location regs */
+ >;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH 6>;
+ atmel,nand-addr-offset = <21>;
+ atmel,nand-cmd-offset = <22>;
+ atmel,nand-has-dma;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_nand>;
+ status = "disabled";
+
+ nfc at 90000000 {
+ compatible = "atmel,sama5d3-nfc";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <
+ 0x90000000 0x08000000 /* NFC Command Registers */
+ 0xfc05c000 0x00000070 /* NFC HSMC regs */
+ 0x00100000 0x00100000 /* NFC SRAM banks */
+ >;
+ clocks = <&hsmc_clk>;
+ atmel,write-by-sram;
+ };
+ };
+
+ apb {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ hlcdc: hlcdc at f0000000 {
+ compatible = "atmel,sama5d4-hlcdc";
+ reg = <0xf0000000 0x4000>;
+ interrupts = <51 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>;
+ clock-names = "periph_clk","sys_clk", "slow_clk";
+ status = "disabled";
+
+ hlcdc-display-controller {
+ compatible = "atmel,hlcdc-display-controller";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+ };
+
+ hlcdc_pwm: hlcdc-pwm {
+ compatible = "atmel,hlcdc-pwm";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_pwm>;
+ #pwm-cells = <3>;
+ };
+ };
+
+ dma1: dma-controller at f0004000 {
+ compatible = "atmel,sama5d4-dma";
+ reg = <0xf0004000 0x200>;
+ interrupts = <50 IRQ_TYPE_LEVEL_HIGH 0>;
+ #dma-cells = <1>;
+ clocks = <&dma1_clk>;
+ clock-names = "dma_clk";
+ };
+
+ isi: isi at f0008000 {
+ compatible = "atmel,at91sam9g45-isi";
+ reg = <0xf0008000 0x4000>;
+ interrupts = <52 IRQ_TYPE_LEVEL_HIGH 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_isi_data_0_7>;
+ clocks = <&isi_clk>;
+ clock-names = "isi_clk";
+ status = "disabled";
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ ramc0: ramc at f0010000 {
+ compatible = "atmel,sama5d3-ddramc";
+ reg = <0xf0010000 0x200>;
+ clocks = <&ddrck>, <&mpddr_clk>;
+ clock-names = "ddrck", "mpddr";
+ };
+
+ dma0: dma-controller at f0014000 {
+ compatible = "atmel,sama5d4-dma";
+ reg = <0xf0014000 0x200>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 0>;
+ #dma-cells = <1>;
+ clocks = <&dma0_clk>;
+ clock-names = "dma_clk";
+ };
+
+ pmc: pmc at f0018000 {
+ compatible = "atmel,sama5d3-pmc", "syscon";
+ reg = <0xf0018000 0x120>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ interrupt-controller;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #interrupt-cells = <1>;
+
+ main_rc_osc: main_rc_osc {
+ compatible = "atmel,at91sam9x5-clk-main-rc-osc";
+ #clock-cells = <0>;
+ interrupt-parent = <&pmc>;
+ interrupts = <AT91_PMC_MOSCRCS>;
+ clock-frequency = <12000000>;
+ clock-accuracy = <100000000>;
+ };
+
+ main_osc: main_osc {
+ compatible = "atmel,at91rm9200-clk-main-osc";
+ #clock-cells = <0>;
+ interrupt-parent = <&pmc>;
+ interrupts = <AT91_PMC_MOSCS>;
+ clocks = <&main_xtal>;
+ };
+
+ main: mainck {
+ compatible = "atmel,at91sam9x5-clk-main";
+ #clock-cells = <0>;
+ interrupt-parent = <&pmc>;
+ interrupts = <AT91_PMC_MOSCSELS>;
+ clocks = <&main_rc_osc &main_osc>;
+ };
+
+ plla: pllack at 0 {
+ compatible = "atmel,sama5d3-clk-pll";
+ #clock-cells = <0>;
+ interrupt-parent = <&pmc>;
+ interrupts = <AT91_PMC_LOCKA>;
+ clocks = <&main>;
+ reg = <0>;
+ atmel,clk-input-range = <12000000 12000000>;
+ #atmel,pll-clk-output-range-cells = <4>;
+ atmel,pll-clk-output-ranges = <600000000 1200000000 0 0>;
+ };
+
+ plladiv: plladivck {
+ compatible = "atmel,at91sam9x5-clk-plldiv";
+ #clock-cells = <0>;
+ clocks = <&plla>;
+ };
+
+ utmi: utmick {
+ compatible = "atmel,at91sam9x5-clk-utmi";
+ #clock-cells = <0>;
+ interrupt-parent = <&pmc>;
+ interrupts = <AT91_PMC_LOCKU>;
+ clocks = <&main>;
+ };
+
+ mck: masterck {
+ compatible = "atmel,at91sam9x5-clk-master";
+ #clock-cells = <0>;
+ interrupt-parent = <&pmc>;
+ interrupts = <AT91_PMC_MCKRDY>;
+ clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>;
+ atmel,clk-output-range = <125000000 200000000>;
+ atmel,clk-divisors = <1 2 4 3>;
+ };
+
+ h32ck: h32mxck {
+ #clock-cells = <0>;
+ compatible = "atmel,sama5d4-clk-h32mx";
+ clocks = <&mck>;
+ };
+
+ usb: usbck {
+ compatible = "atmel,at91sam9x5-clk-usb";
+ #clock-cells = <0>;
+ clocks = <&plladiv>, <&utmi>;
+ };
+
+ prog: progck {
+ compatible = "atmel,at91sam9x5-clk-programmable";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-parent = <&pmc>;
+ clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>;
+
+ prog0: prog at 0 {
+ #clock-cells = <0>;
+ reg = <0>;
+ interrupts = <AT91_PMC_PCKRDY(0)>;
+ };
+
+ prog1: prog at 1 {
+ #clock-cells = <0>;
+ reg = <1>;
+ interrupts = <AT91_PMC_PCKRDY(1)>;
+ };
+
+ prog2: prog at 2 {
+ #clock-cells = <0>;
+ reg = <2>;
+ interrupts = <AT91_PMC_PCKRDY(2)>;
+ };
+ };
+
+ smd: smdclk {
+ compatible = "atmel,at91sam9x5-clk-smd";
+ #clock-cells = <0>;
+ clocks = <&plladiv>, <&utmi>;
+ };
+
+ systemck {
+ compatible = "atmel,at91rm9200-clk-system";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ddrck: ddrck at 2 {
+ #clock-cells = <0>;
+ reg = <2>;
+ clocks = <&mck>;
+ };
+
+ lcdck: lcdck at 3 {
+ #clock-cells = <0>;
+ reg = <3>;
+ clocks = <&mck>;
+ };
+
+ smdck: smdck at 4 {
+ #clock-cells = <0>;
+ reg = <4>;
+ clocks = <&smd>;
+ };
+
+ uhpck: uhpcki at 6 {
+ #clock-cells = <0>;
+ reg = <6>;
+ clocks = <&usb>;
+ };
+
+ udpck: udpck at 7 {
+ #clock-cells = <0>;
+ reg = <7>;
+ clocks = <&usb>;
+ };
+
+ pck0: pck0 at 8 {
+ #clock-cells = <0>;
+ reg = <8>;
+ clocks = <&prog0>;
+ };
+
+ pck1: pck1 at 9 {
+ #clock-cells = <0>;
+ reg = <9>;
+ clocks = <&prog1>;
+ };
+
+ pck2: pck2 at 10 {
+ #clock-cells = <0>;
+ reg = <10>;
+ clocks = <&prog2>;
+ };
+ };
+
+ periph32ck {
+ compatible = "atmel,at91sam9x5-clk-peripheral";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&h32ck>;
+
+ pioD_clk: pioD_clk at 5 {
+ #clock-cells = <0>;
+ reg = <5>;
+ };
+
+ usart0_clk: usart0_clk at 6 {
+ #clock-cells = <0>;
+ reg = <6>;
+ };
+
+ usart1_clk: usart1_clk at 7 {
+ #clock-cells = <0>;
+ reg = <7>;
+ };
+
+ icm_clk: icm_clk at 9 {
+ #clock-cells = <0>;
+ reg = <9>;
+ };
+
+ aes_clk: aes_clk at 12 {
+ #clock-cells = <0>;
+ reg = <12>;
+ };
+
+ tdes_clk: tdes_clk at 14 {
+ #clock-cells = <0>;
+ reg = <14>;
+ };
+
+ sha_clk: sha_clk at 15 {
+ #clock-cells = <0>;
+ reg = <15>;
+ };
+
+ matrix1_clk: matrix1_clk at 17 {
+ #clock-cells = <0>;
+ reg = <17>;
+ };
+
+ hsmc_clk: hsmc_clk at 22 {
+ #clock-cells = <0>;
+ reg = <22>;
+ };
+
+ pioA_clk: pioA_clk at 23 {
+ #clock-cells = <0>;
+ reg = <23>;
+ };
+
+ pioB_clk: pioB_clk at 24 {
+ #clock-cells = <0>;
+ reg = <24>;
+ };
+
+ pioC_clk: pioC_clk at 25 {
+ #clock-cells = <0>;
+ reg = <25>;
+ };
+
+ pioE_clk: pioE_clk at 26 {
+ #clock-cells = <0>;
+ reg = <26>;
+ };
+
+ uart0_clk: uart0_clk at 27 {
+ #clock-cells = <0>;
+ reg = <27>;
+ };
+
+ uart1_clk: uart1_clk at 28 {
+ #clock-cells = <0>;
+ reg = <28>;
+ };
+
+ usart2_clk: usart2_clk at 29 {
+ #clock-cells = <0>;
+ reg = <29>;
+ };
+
+ usart3_clk: usart3_clk at 30 {
+ #clock-cells = <0>;
+ reg = <30>;
+ };
+
+ usart4_clk: usart4_clk at 31 {
+ #clock-cells = <0>;
+ reg = <31>;
+ };
+
+ twi0_clk: twi0_clk at 32 {
+ reg = <32>;
+ #clock-cells = <0>;
+ };
+
+ twi1_clk: twi1_clk at 33 {
+ #clock-cells = <0>;
+ reg = <33>;
+ };
+
+ twi2_clk: twi2_clk at 34 {
+ #clock-cells = <0>;
+ reg = <34>;
+ };
+
+ mci0_clk: mci0_clk at 35 {
+ #clock-cells = <0>;
+ reg = <35>;
+ };
+
+ mci1_clk: mci1_clk at 36 {
+ #clock-cells = <0>;
+ reg = <36>;
+ };
+
+ spi0_clk: spi0_clk at 37 {
+ #clock-cells = <0>;
+ reg = <37>;
+ };
+
+ spi1_clk: spi1_clk at 38 {
+ #clock-cells = <0>;
+ reg = <38>;
+ };
+
+ spi2_clk: spi2_clk at 39 {
+ #clock-cells = <0>;
+ reg = <39>;
+ };
+
+ tcb0_clk: tcb0_clk at 40 {
+ #clock-cells = <0>;
+ reg = <40>;
+ };
+
+ tcb1_clk: tcb1_clk at 41 {
+ #clock-cells = <0>;
+ reg = <41>;
+ };
+
+ tcb2_clk: tcb2_clk at 42 {
+ #clock-cells = <0>;
+ reg = <42>;
+ };
+
+ pwm_clk: pwm_clk at 43 {
+ #clock-cells = <0>;
+ reg = <43>;
+ };
+
+ adc_clk: adc_clk at 44 {
+ #clock-cells = <0>;
+ reg = <44>;
+ };
+
+ dbgu_clk: dbgu_clk at 45 {
+ #clock-cells = <0>;
+ reg = <45>;
+ };
+
+ uhphs_clk: uhphs_clk at 46 {
+ #clock-cells = <0>;
+ reg = <46>;
+ };
+
+ udphs_clk: udphs_clk at 47 {
+ #clock-cells = <0>;
+ reg = <47>;
+ };
+
+ ssc0_clk: ssc0_clki at 48 {
+ #clock-cells = <0>;
+ reg = <48>;
+ };
+
+ ssc1_clk: ssc1_clk at 49 {
+ #clock-cells = <0>;
+ reg = <49>;
+ };
+
+ trng_clk: trng_clk at 53 {
+ #clock-cells = <0>;
+ reg = <53>;
+ };
+
+ macb0_clk: macb0_clk at 54 {
+ #clock-cells = <0>;
+ reg = <54>;
+ };
+
+ macb1_clk: macb1_clk at 55 {
+ #clock-cells = <0>;
+ reg = <55>;
+ };
+
+ fuse_clk: fuse_clk at 57 {
+ #clock-cells = <0>;
+ reg = <57>;
+ };
+
+ securam_clk: securam_clk at 59 {
+ #clock-cells = <0>;
+ reg = <59>;
+ };
+
+ smd_clk: smd_clk at 61 {
+ #clock-cells = <0>;
+ reg = <61>;
+ };
+
+ twi3_clk: twi3_clk at 62 {
+ #clock-cells = <0>;
+ reg = <62>;
+ };
+
+ catb_clk: catb_clk at 63 {
+ #clock-cells = <0>;
+ reg = <63>;
+ };
+ };
+
+ periph64ck {
+ compatible = "atmel,at91sam9x5-clk-peripheral";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&mck>;
+
+ dma0_clk: dma0_clk at 8 {
+ #clock-cells = <0>;
+ reg = <8>;
+ };
+
+ cpkcc_clk: cpkcc_clk at 10 {
+ #clock-cells = <0>;
+ reg = <10>;
+ };
+
+ aesb_clk: aesb_clk at 13 {
+ #clock-cells = <0>;
+ reg = <13>;
+ };
+
+ mpddr_clk: mpddr_clk at 16 {
+ #clock-cells = <0>;
+ reg = <16>;
+ };
+
+ matrix0_clk: matrix0_clk at 18 {
+ #clock-cells = <0>;
+ reg = <18>;
+ };
+
+ vdec_clk: vdec_clk at 19 {
+ #clock-cells = <0>;
+ reg = <19>;
+ };
+
+ dma1_clk: dma1_clk at 50 {
+ #clock-cells = <0>;
+ reg = <50>;
+ };
+
+ lcdc_clk: lcdc_clk at 51 {
+ #clock-cells = <0>;
+ reg = <51>;
+ };
+
+ isi_clk: isi_clk at 52 {
+ #clock-cells = <0>;
+ reg = <52>;
+ };
+ };
+ };
+
+ mmc0: mmc at f8000000 {
+ compatible = "atmel,hsmci";
+ reg = <0xf8000000 0x600>;
+ interrupts = <35 IRQ_TYPE_LEVEL_HIGH 0>;
+ dmas = <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(0))>;
+ dma-names = "rxtx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&mci0_clk>;
+ clock-names = "mci_clk";
+ };
+
+ uart0: serial at f8004000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xf8004000 0x100>;
+ interrupts = <27 IRQ_TYPE_LEVEL_HIGH 5>;
+ dmas = <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(22))>,
+ <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(23))>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0>;
+ clocks = <&uart0_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ ssc0: ssc at f8008000 {
+ compatible = "atmel,at91sam9g45-ssc";
+ reg = <0xf8008000 0x4000>;
+ interrupts = <48 IRQ_TYPE_LEVEL_HIGH 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
+ dmas = <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(26))>,
+ <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(27))>;
+ dma-names = "tx", "rx";
+ clocks = <&ssc0_clk>;
+ clock-names = "pclk";
+ status = "disabled";
+ };
+
+ pwm0: pwm at f800c000 {
+ compatible = "atmel,sama5d3-pwm";
+ reg = <0xf800c000 0x300>;
+ interrupts = <43 IRQ_TYPE_LEVEL_HIGH 4>;
+ #pwm-cells = <3>;
+ clocks = <&pwm_clk>;
+ status = "disabled";
+ };
+
+ spi0: spi at f8010000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "atmel,at91rm9200-spi";
+ reg = <0xf8010000 0x100>;
+ interrupts = <37 IRQ_TYPE_LEVEL_HIGH 3>;
+ dmas = <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(10))>,
+ <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(11))>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi0>;
+ clocks = <&spi0_clk>;
+ clock-names = "spi_clk";
+ status = "disabled";
+ };
+
+ i2c0: i2c at f8014000 {
+ compatible = "atmel,sama5d4-i2c";
+ reg = <0xf8014000 0x4000>;
+ interrupts = <32 IRQ_TYPE_LEVEL_HIGH 6>;
+ dmas = <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(2))>,
+ <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(3))>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&twi0_clk>;
+ status = "disabled";
+ };
+
+ i2c1: i2c at f8018000 {
+ compatible = "atmel,sama5d4-i2c";
+ reg = <0xf8018000 0x4000>;
+ interrupts = <33 IRQ_TYPE_LEVEL_HIGH 6>;
+ dmas = <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(4))>,
+ <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(5))>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&twi1_clk>;
+ status = "disabled";
+ };
+
+ tcb0: timer at f801c000 {
+ compatible = "atmel,at91sam9x5-tcb";
+ reg = <0xf801c000 0x100>;
+ interrupts = <40 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&tcb0_clk>, <&clk32k>;
+ clock-names = "t0_clk", "slow_clk";
+ };
+
+ macb0: ethernet at f8020000 {
+ compatible = "atmel,sama5d4-gem";
+ reg = <0xf8020000 0x100>;
+ interrupts = <54 IRQ_TYPE_LEVEL_HIGH 3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_macb0_rmii>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&macb0_clk>, <&macb0_clk>;
+ clock-names = "hclk", "pclk";
+ status = "disabled";
+ };
+
+ i2c2: i2c at f8024000 {
+ compatible = "atmel,sama5d4-i2c";
+ reg = <0xf8024000 0x4000>;
+ interrupts = <34 IRQ_TYPE_LEVEL_HIGH 6>;
+ dmas = <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(6))>,
+ <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(7))>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&twi2_clk>;
+ status = "disabled";
+ };
+
+ sfr: sfr at f8028000 {
+ compatible = "atmel,sama5d4-sfr", "syscon";
+ reg = <0xf8028000 0x60>;
+ };
+
+ usart0: serial at f802c000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xf802c000 0x100>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(36))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(37))>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart0 &pinctrl_usart0_rts &pinctrl_usart0_cts>;
+ clocks = <&usart0_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ usart1: serial at f8030000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xf8030000 0x100>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(38))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(39))>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts &pinctrl_usart1_cts>;
+ clocks = <&usart1_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ mmc1: mmc at fc000000 {
+ compatible = "atmel,hsmci";
+ reg = <0xfc000000 0x600>;
+ interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>;
+ dmas = <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(1))>;
+ dma-names = "rxtx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&mci1_clk>;
+ clock-names = "mci_clk";
+ };
+
+ uart1: serial at fc004000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xfc004000 0x100>;
+ interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>;
+ dmas = <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(24))>,
+ <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(25))>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ clocks = <&uart1_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ usart2: serial at fc008000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xfc008000 0x100>;
+ interrupts = <29 IRQ_TYPE_LEVEL_HIGH 5>;
+ dmas = <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(16))>,
+ <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(17))>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart2 &pinctrl_usart2_rts &pinctrl_usart2_cts>;
+ clocks = <&usart2_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ usart3: serial at fc00c000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xfc00c000 0x100>;
+ interrupts = <30 IRQ_TYPE_LEVEL_HIGH 5>;
+ dmas = <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(18))>,
+ <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(19))>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart3>;
+ clocks = <&usart3_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ usart4: serial at fc010000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xfc010000 0x100>;
+ interrupts = <31 IRQ_TYPE_LEVEL_HIGH 5>;
+ dmas = <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(20))>,
+ <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(21))>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart4>;
+ clocks = <&usart4_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ ssc1: ssc at fc014000 {
+ compatible = "atmel,at91sam9g45-ssc";
+ reg = <0xfc014000 0x4000>;
+ interrupts = <49 IRQ_TYPE_LEVEL_HIGH 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>;
+ dmas = <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(28))>,
+ <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(29))>;
+ dma-names = "tx", "rx";
+ clocks = <&ssc1_clk>;
+ clock-names = "pclk";
+ status = "disabled";
+ };
+
+ spi1: spi at fc018000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "atmel,at91rm9200-spi";
+ reg = <0xfc018000 0x100>;
+ interrupts = <38 IRQ_TYPE_LEVEL_HIGH 3>;
+ dmas = <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(12))>,
+ <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(13))>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi1>;
+ clocks = <&spi1_clk>;
+ clock-names = "spi_clk";
+ status = "disabled";
+ };
+
+ spi2: spi at fc01c000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "atmel,at91rm9200-spi";
+ reg = <0xfc01c000 0x100>;
+ interrupts = <39 IRQ_TYPE_LEVEL_HIGH 3>;
+ dmas = <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(14))>,
+ <&dma1
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(15))>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi2>;
+ clocks = <&spi2_clk>;
+ clock-names = "spi_clk";
+ status = "disabled";
+ };
+
+ tcb1: timer at fc020000 {
+ compatible = "atmel,at91sam9x5-tcb";
+ reg = <0xfc020000 0x100>;
+ interrupts = <41 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&tcb1_clk>, <&clk32k>;
+ clock-names = "t0_clk", "slow_clk";
+ };
+
+ macb1: ethernet at fc028000 {
+ compatible = "atmel,sama5d4-gem";
+ reg = <0xfc028000 0x100>;
+ interrupts = <55 IRQ_TYPE_LEVEL_HIGH 3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_macb1_rmii>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&macb1_clk>, <&macb1_clk>;
+ clock-names = "hclk", "pclk";
+ status = "disabled";
+ };
+
+ trng at fc030000 {
+ compatible = "atmel,at91sam9g45-trng";
+ reg = <0xfc030000 0x100>;
+ interrupts = <53 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&trng_clk>;
+ };
+
+ adc0: adc at fc034000 {
+ compatible = "atmel,at91sam9x5-adc";
+ reg = <0xfc034000 0x100>;
+ interrupts = <44 IRQ_TYPE_LEVEL_HIGH 5>;
+ clocks = <&adc_clk>,
+ <&adc_op_clk>;
+ clock-names = "adc_clk", "adc_op_clk";
+ atmel,adc-channels-used = <0x01f>;
+ atmel,adc-startup-time = <40>;
+ atmel,adc-use-external-triggers;
+ atmel,adc-vref = <3000>;
+ atmel,adc-res = <8 10>;
+ atmel,adc-sample-hold-time = <11>;
+ atmel,adc-res-names = "lowres", "highres";
+ atmel,adc-ts-pressure-threshold = <10000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+
+ trigger at 0 {
+ trigger-name = "external-rising";
+ trigger-value = <0x1>;
+ trigger-external;
+ reg = <0>;
+ };
+ trigger at 1 {
+ trigger-name = "external-falling";
+ trigger-value = <0x2>;
+ trigger-external;
+ reg = <1>;
+ };
+ trigger at 2 {
+ trigger-name = "external-any";
+ trigger-value = <0x3>;
+ trigger-external;
+ reg = <2>;
+ };
+ trigger at 3 {
+ trigger-name = "continuous";
+ trigger-value = <0x6>;
+ reg = <3>;
+ };
+ };
+
+ aes at fc044000 {
+ compatible = "atmel,at91sam9g46-aes";
+ reg = <0xfc044000 0x100>;
+ interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
+ dmas = <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(41))>,
+ <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(40))>;
+ dma-names = "tx", "rx";
+ clocks = <&aes_clk>;
+ clock-names = "aes_clk";
+ status = "okay";
+ };
+
+ tdes at fc04c000 {
+ compatible = "atmel,at91sam9g46-tdes";
+ reg = <0xfc04c000 0x100>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 0>;
+ dmas = <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(42))>,
+ <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(43))>;
+ dma-names = "tx", "rx";
+ clocks = <&tdes_clk>;
+ clock-names = "tdes_clk";
+ status = "okay";
+ };
+
+ sha at fc050000 {
+ compatible = "atmel,at91sam9g46-sha";
+ reg = <0xfc050000 0x100>;
+ interrupts = <15 IRQ_TYPE_LEVEL_HIGH 0>;
+ dmas = <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+ | AT91_XDMAC_DT_PERID(44))>;
+ dma-names = "tx";
+ clocks = <&sha_clk>;
+ clock-names = "sha_clk";
+ status = "okay";
+ };
+
+ rstc at fc068600 {
+ compatible = "atmel,sama5d3-rstc", "atmel,at91sam9g45-rstc";
+ reg = <0xfc068600 0x10>;
+ clocks = <&clk32k>;
+ };
+
+ shdwc at fc068610 {
+ compatible = "atmel,at91sam9x5-shdwc";
+ reg = <0xfc068610 0x10>;
+ clocks = <&clk32k>;
+ };
+
+ pit: timer at fc068630 {
+ compatible = "atmel,at91sam9260-pit";
+ reg = <0xfc068630 0x10>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH 5>;
+ clocks = <&h32ck>;
+ };
+
+ watchdog at fc068640 {
+ compatible = "atmel,sama5d4-wdt";
+ reg = <0xfc068640 0x10>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&clk32k>;
+ status = "disabled";
+ };
+
+ sckc at fc068650 {
+ compatible = "atmel,at91sam9x5-sckc";
+ reg = <0xfc068650 0x4>;
+
+ slow_rc_osc: slow_rc_osc {
+ compatible = "atmel,at91sam9x5-clk-slow-rc-osc";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-accuracy = <250000000>;
+ atmel,startup-time-usec = <75>;
+ };
+
+ slow_osc: slow_osc {
+ compatible = "atmel,at91sam9x5-clk-slow-osc";
+ #clock-cells = <0>;
+ clocks = <&slow_xtal>;
+ atmel,startup-time-usec = <1200000>;
+ };
+
+ clk32k: slowck {
+ compatible = "atmel,at91sam9x5-clk-slow";
+ #clock-cells = <0>;
+ clocks = <&slow_rc_osc &slow_osc>;
+ };
+ };
+
+ rtc at fc0686b0 {
+ compatible = "atmel,at91rm9200-rtc";
+ reg = <0xfc0686b0 0x30>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&clk32k>;
+ };
+
+ dbgu: serial at fc069000 {
+ compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+ reg = <0xfc069000 0x200>;
+ interrupts = <45 IRQ_TYPE_LEVEL_HIGH 7>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_dbgu>;
+ clocks = <&dbgu_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ pioA: gpio at fc06a000 {
+ compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfc06a000 0x100>;
+ interrupts = <23 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioA_clk>;
+ };
+
+ pioB: gpio at fc06b000 {
+ compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfc06b000 0x100>;
+ interrupts = <24 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioB_clk>;
+ };
+
+ pioC: gpio at fc06c000 {
+ compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfc06c000 0x100>;
+ interrupts = <25 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioC_clk>;
+ };
+
+ pioD: gpio at fc068000 {
+ compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfc068000 0x100>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioD_clk>;
+ };
+
+ pioE: gpio at fc06d000 {
+ compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfc06d000 0x100>;
+ interrupts = <26 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioE_clk>;
+ };
+
+ pinctrl at fc06a000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "atmel,at91sam9x5-pinctrl", "atmel,at91rm9200-pinctrl", "simple-bus";
+ ranges = <0xfc068000 0xfc068000 0x100
+ 0xfc06a000 0xfc06a000 0x4000>;
+ /* WARNING: revisit as pin spec has changed */
+ atmel,mux-mask = <
+ /* A B C */
+ 0xffffffff 0x3ffcfe7c 0x1c010101 /* pioA */
+ 0x7fffffff 0xfffccc3a 0x3f00cc3a /* pioB */
+ 0xffffffff 0x3ff83fff 0xff00ffff /* pioC */
+ 0x0003ff00 0x8002a800 0x00000000 /* pioD */
+ 0xffffffff 0x7fffffff 0x76fff1bf /* pioE */
+ >;
+ reg = < 0xfc06a000 0x100
+ 0xfc06b000 0x100
+ 0xfc06c000 0x100
+ 0xfc068000 0x100
+ 0xfc06d000 0x100
+ >;
+
+ /* pinctrl pin settings */
+ adc0 {
+ pinctrl_adc0_adtrg: adc0_adtrg {
+ atmel,pins =
+ <AT91_PIOE 31 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* conflicts with USBA_VBUS */
+ };
+ pinctrl_adc0_ad0: adc0_ad0 {
+ atmel,pins =
+ <AT91_PIOC 27 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ pinctrl_adc0_ad1: adc0_ad1 {
+ atmel,pins =
+ <AT91_PIOC 28 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ pinctrl_adc0_ad2: adc0_ad2 {
+ atmel,pins =
+ <AT91_PIOC 29 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ pinctrl_adc0_ad3: adc0_ad3 {
+ atmel,pins =
+ <AT91_PIOC 30 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ pinctrl_adc0_ad4: adc0_ad4 {
+ atmel,pins =
+ <AT91_PIOC 31 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ };
+
+ dbgu {
+ pinctrl_dbgu: dbgu-0 {
+ atmel,pins =
+ <AT91_PIOB 24 AT91_PERIPH_A AT91_PINCTRL_NONE>, /* conflicts with D14 and TDI */
+ <AT91_PIOB 25 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* conflicts with D15 and TDO */
+ };
+ };
+
+ i2c0 {
+ pinctrl_i2c0: i2c0-0 {
+ atmel,pins =
+ <AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_NONE
+ AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ };
+
+ i2c1 {
+ pinctrl_i2c1: i2c1-0 {
+ atmel,pins =
+ <AT91_PIOE 29 AT91_PERIPH_C AT91_PINCTRL_NONE /* TWD1, conflicts with UART0 RX and DIBP */
+ AT91_PIOE 30 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* TWCK1, conflicts with UART0 TX and DIBN */
+ };
+ };
+
+ i2c2 {
+ pinctrl_i2c2: i2c2-0 {
+ atmel,pins =
+ <AT91_PIOB 29 AT91_PERIPH_A AT91_PINCTRL_NONE /* TWD2, conflicts with RD0 and PWML1 */
+ AT91_PIOB 30 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* TWCK2, conflicts with RF0 */
+ };
+ };
+
+ isi {
+ pinctrl_isi_data_0_7: isi-0-data-0-7 {
+ atmel,pins =
+ <AT91_PIOC 19 AT91_PERIPH_A AT91_PINCTRL_NONE /* ISI_D0 */
+ AT91_PIOC 20 AT91_PERIPH_A AT91_PINCTRL_NONE /* ISI_D1 */
+ AT91_PIOC 21 AT91_PERIPH_A AT91_PINCTRL_NONE /* ISI_D2 */
+ AT91_PIOC 22 AT91_PERIPH_A AT91_PINCTRL_NONE /* ISI_D3 */
+ AT91_PIOC 23 AT91_PERIPH_A AT91_PINCTRL_NONE /* ISI_D4 */
+ AT91_PIOC 24 AT91_PERIPH_A AT91_PINCTRL_NONE /* ISI_D5 */
+ AT91_PIOC 25 AT91_PERIPH_A AT91_PINCTRL_NONE /* ISI_D6 */
+ AT91_PIOC 26 AT91_PERIPH_A AT91_PINCTRL_NONE /* ISI_D7 */
+ AT91_PIOB 1 AT91_PERIPH_C AT91_PINCTRL_NONE /* ISI_PCK, conflict with G0_RXCK */
+ AT91_PIOB 3 AT91_PERIPH_C AT91_PINCTRL_NONE /* ISI_VSYNC */
+ AT91_PIOB 4 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* ISI_HSYNC */
+ };
+ pinctrl_isi_data_8_9: isi-0-data-8-9 {
+ atmel,pins =
+ <AT91_PIOC 0 AT91_PERIPH_C AT91_PINCTRL_NONE /* ISI_D8, conflicts with SPI0_MISO, PWMH2 */
+ AT91_PIOC 1 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* ISI_D9, conflicts with SPI0_MOSI, PWML2 */
+ };
+ pinctrl_isi_data_10_11: isi-0-data-10-11 {
+ atmel,pins =
+ <AT91_PIOC 2 AT91_PERIPH_C AT91_PINCTRL_NONE /* ISI_D10, conflicts with SPI0_SPCK, PWMH3 */
+ AT91_PIOC 3 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* ISI_D11, conflicts with SPI0_NPCS0, PWML3 */
+ };
+ };
+
+ lcd {
+ pinctrl_lcd_base: lcd-base-0 {
+ atmel,pins =
+ <AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDVSYNC */
+ AT91_PIOA 27 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDHSYNC */
+ AT91_PIOA 29 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDDEN */
+ AT91_PIOA 28 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* LCDPCK */
+ };
+ pinctrl_lcd_pwm: lcd-pwm-0 {
+ atmel,pins = <AT91_PIOA 24 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* LCDPWM */
+ };
+ pinctrl_lcd_rgb444: lcd-rgb-0 {
+ atmel,pins =
+ <AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD0 pin */
+ AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD1 pin */
+ AT91_PIOA 2 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD2 pin */
+ AT91_PIOA 3 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD3 pin */
+ AT91_PIOA 4 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD4 pin */
+ AT91_PIOA 5 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD5 pin */
+ AT91_PIOA 6 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD6 pin */
+ AT91_PIOA 7 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD7 pin */
+ AT91_PIOA 8 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD8 pin */
+ AT91_PIOA 9 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD9 pin */
+ AT91_PIOA 10 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD10 pin */
+ AT91_PIOA 11 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* LCDD11 pin */
+ };
+ pinctrl_lcd_rgb565: lcd-rgb-1 {
+ atmel,pins =
+ <AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD0 pin */
+ AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD1 pin */
+ AT91_PIOA 2 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD2 pin */
+ AT91_PIOA 3 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD3 pin */
+ AT91_PIOA 4 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD4 pin */
+ AT91_PIOA 5 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD5 pin */
+ AT91_PIOA 6 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD6 pin */
+ AT91_PIOA 7 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD7 pin */
+ AT91_PIOA 8 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD8 pin */
+ AT91_PIOA 9 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD9 pin */
+ AT91_PIOA 10 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD10 pin */
+ AT91_PIOA 11 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD11 pin */
+ AT91_PIOA 12 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD12 pin */
+ AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD13 pin */
+ AT91_PIOA 14 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD14 pin */
+ AT91_PIOA 15 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* LCDD15 pin */
+ };
+ pinctrl_lcd_rgb666: lcd-rgb-2 {
+ atmel,pins =
+ <AT91_PIOA 2 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD2 pin */
+ AT91_PIOA 3 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD3 pin */
+ AT91_PIOA 4 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD4 pin */
+ AT91_PIOA 5 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD5 pin */
+ AT91_PIOA 6 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD6 pin */
+ AT91_PIOA 7 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD7 pin */
+ AT91_PIOA 10 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD10 pin */
+ AT91_PIOA 11 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD11 pin */
+ AT91_PIOA 12 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD12 pin */
+ AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD13 pin */
+ AT91_PIOA 14 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD14 pin */
+ AT91_PIOA 15 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD15 pin */
+ AT91_PIOA 18 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD18 pin */
+ AT91_PIOA 19 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD19 pin */
+ AT91_PIOA 20 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD20 pin */
+ AT91_PIOA 21 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD21 pin */
+ AT91_PIOA 22 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD22 pin */
+ AT91_PIOA 23 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* LCDD23 pin */
+ };
+ pinctrl_lcd_rgb777: lcd-rgb-3 {
+ atmel,pins =
+ /* LCDDAT0 conflicts with TMS */
+ <AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD1 pin */
+ AT91_PIOA 2 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD2 pin */
+ AT91_PIOA 3 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD3 pin */
+ AT91_PIOA 4 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD4 pin */
+ AT91_PIOA 5 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD5 pin */
+ AT91_PIOA 6 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD6 pin */
+ AT91_PIOA 7 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD7 pin */
+ /* LCDDAT8 conflicts with TCK */
+ AT91_PIOA 9 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD9 pin */
+ AT91_PIOA 10 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD10 pin */
+ AT91_PIOA 11 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD11 pin */
+ AT91_PIOA 12 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD12 pin */
+ AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD13 pin */
+ AT91_PIOA 14 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD14 pin */
+ AT91_PIOA 15 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD15 pin */
+ /* LCDDAT16 conflicts with NTRST */
+ AT91_PIOA 17 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD17 pin */
+ AT91_PIOA 18 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD18 pin */
+ AT91_PIOA 19 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD19 pin */
+ AT91_PIOA 20 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD20 pin */
+ AT91_PIOA 21 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD21 pin */
+ AT91_PIOA 22 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD22 pin */
+ AT91_PIOA 23 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* LCDD23 pin */
+ };
+ pinctrl_lcd_rgb888: lcd-rgb-4 {
+ atmel,pins =
+ <AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD0 pin */
+ AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD1 pin */
+ AT91_PIOA 2 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD2 pin */
+ AT91_PIOA 3 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD3 pin */
+ AT91_PIOA 4 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD4 pin */
+ AT91_PIOA 5 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD5 pin */
+ AT91_PIOA 6 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD6 pin */
+ AT91_PIOA 7 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD7 pin */
+ AT91_PIOA 8 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD8 pin */
+ AT91_PIOA 9 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD9 pin */
+ AT91_PIOA 10 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD10 pin */
+ AT91_PIOA 11 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD11 pin */
+ AT91_PIOA 12 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD12 pin */
+ AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD13 pin */
+ AT91_PIOA 14 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD14 pin */
+ AT91_PIOA 15 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD15 pin */
+ AT91_PIOA 16 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD16 pin */
+ AT91_PIOA 17 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD17 pin */
+ AT91_PIOA 18 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD18 pin */
+ AT91_PIOA 19 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD19 pin */
+ AT91_PIOA 20 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD20 pin */
+ AT91_PIOA 21 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD21 pin */
+ AT91_PIOA 22 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD22 pin */
+ AT91_PIOA 23 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* LCDD23 pin */
+ };
+ };
+
+ macb0 {
+ pinctrl_macb0_rmii: macb0_rmii-0 {
+ atmel,pins =
+ <AT91_PIOB 12 AT91_PERIPH_A AT91_PINCTRL_NONE /* G0_TX0 */
+ AT91_PIOB 13 AT91_PERIPH_A AT91_PINCTRL_NONE /* G0_TX1 */
+ AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_NONE /* G0_RX0 */
+ AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_NONE /* G0_RX1 */
+ AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_NONE /* G0_RXDV */
+ AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_NONE /* G0_RXER */
+ AT91_PIOB 2 AT91_PERIPH_A AT91_PINCTRL_NONE /* G0_TXEN */
+ AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_NONE /* G0_TXCK */
+ AT91_PIOB 16 AT91_PERIPH_A AT91_PINCTRL_NONE /* G0_MDC */
+ AT91_PIOB 17 AT91_PERIPH_A AT91_PINCTRL_NONE /* G0_MDIO */
+ >;
+ };
+ };
+
+ macb1 {
+ pinctrl_macb1_rmii: macb1_rmii-0 {
+ atmel,pins =
+ <AT91_PIOA 14 AT91_PERIPH_B AT91_PINCTRL_NONE /* G1_TX0 */
+ AT91_PIOA 15 AT91_PERIPH_B AT91_PINCTRL_NONE /* G1_TX1 */
+ AT91_PIOA 12 AT91_PERIPH_B AT91_PINCTRL_NONE /* G1_RX0 */
+ AT91_PIOA 13 AT91_PERIPH_B AT91_PINCTRL_NONE /* G1_RX1 */
+ AT91_PIOA 10 AT91_PERIPH_B AT91_PINCTRL_NONE /* G1_RXDV */
+ AT91_PIOA 11 AT91_PERIPH_B AT91_PINCTRL_NONE /* G1_RXER */
+ AT91_PIOA 4 AT91_PERIPH_B AT91_PINCTRL_NONE /* G1_TXEN */
+ AT91_PIOA 2 AT91_PERIPH_B AT91_PINCTRL_NONE /* G1_TXCK */
+ AT91_PIOA 22 AT91_PERIPH_B AT91_PINCTRL_NONE /* G1_MDC */
+ AT91_PIOA 23 AT91_PERIPH_B AT91_PINCTRL_NONE /* G1_MDIO */
+ >;
+ };
+ };
+
+ mmc0 {
+ pinctrl_mmc0_clk_cmd_dat0: mmc0_clk_cmd_dat0 {
+ atmel,pins =
+ <AT91_PIOC 4 AT91_PERIPH_B AT91_PINCTRL_NONE /* MCI0_CK, conflict with PCK1(ISI_MCK) */
+ AT91_PIOC 5 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_CDA, conflict with NAND_D0 */
+ AT91_PIOC 6 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_DA0, conflict with NAND_D1 */
+ >;
+ };
+ pinctrl_mmc0_dat1_3: mmc0_dat1_3 {
+ atmel,pins =
+ <AT91_PIOC 7 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_DA1, conflict with NAND_D2 */
+ AT91_PIOC 8 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_DA2, conflict with NAND_D3 */
+ AT91_PIOC 9 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_DA3, conflict with NAND_D4 */
+ >;
+ };
+ pinctrl_mmc0_dat4_7: mmc0_dat4_7 {
+ atmel,pins =
+ <AT91_PIOC 10 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_DA4, conflict with NAND_D5 */
+ AT91_PIOC 11 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_DA5, conflict with NAND_D6 */
+ AT91_PIOC 12 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_DA6, conflict with NAND_D7 */
+ AT91_PIOC 13 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_DA7, conflict with NAND_OE */
+ >;
+ };
+ };
+
+ mmc1 {
+ pinctrl_mmc1_clk_cmd_dat0: mmc1_clk_cmd_dat0 {
+ atmel,pins =
+ <AT91_PIOE 18 AT91_PERIPH_C AT91_PINCTRL_NONE /* MCI1_CK */
+ AT91_PIOE 19 AT91_PERIPH_C AT91_PINCTRL_PULL_UP /* MCI1_CDA */
+ AT91_PIOE 20 AT91_PERIPH_C AT91_PINCTRL_PULL_UP /* MCI1_DA0 */
+ >;
+ };
+ pinctrl_mmc1_dat1_3: mmc1_dat1_3 {
+ atmel,pins =
+ <AT91_PIOE 21 AT91_PERIPH_C AT91_PINCTRL_PULL_UP /* MCI1_DA1 */
+ AT91_PIOE 22 AT91_PERIPH_C AT91_PINCTRL_PULL_UP /* MCI1_DA2 */
+ AT91_PIOE 23 AT91_PERIPH_C AT91_PINCTRL_PULL_UP /* MCI1_DA3 */
+ >;
+ };
+ };
+
+ nand0 {
+ pinctrl_nand: nand-0 {
+ atmel,pins =
+ <AT91_PIOC 13 AT91_PERIPH_A AT91_PINCTRL_NONE /* PC13 periph A Read Enable */
+ AT91_PIOC 14 AT91_PERIPH_A AT91_PINCTRL_NONE /* PC14 periph A Write Enable */
+
+ AT91_PIOC 17 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PC17 ALE */
+ AT91_PIOC 18 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PC18 CLE */
+
+ AT91_PIOC 15 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PC15 NCS3/Chip Enable */
+ AT91_PIOC 16 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PC16 NANDRDY */
+ AT91_PIOC 5 AT91_PERIPH_A AT91_PINCTRL_NONE /* PC5 Data bit 0 */
+ AT91_PIOC 6 AT91_PERIPH_A AT91_PINCTRL_NONE /* PC6 Data bit 1 */
+ AT91_PIOC 7 AT91_PERIPH_A AT91_PINCTRL_NONE /* PC7 Data bit 2 */
+ AT91_PIOC 8 AT91_PERIPH_A AT91_PINCTRL_NONE /* PC8 Data bit 3 */
+ AT91_PIOC 9 AT91_PERIPH_A AT91_PINCTRL_NONE /* PC9 Data bit 4 */
+ AT91_PIOC 10 AT91_PERIPH_A AT91_PINCTRL_NONE /* PC10 Data bit 5 */
+ AT91_PIOC 11 AT91_PERIPH_A AT91_PINCTRL_NONE /* PC11 periph A Data bit 6 */
+ AT91_PIOC 12 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PC12 periph A Data bit 7 */
+ };
+ };
+
+ spi0 {
+ pinctrl_spi0: spi0-0 {
+ atmel,pins =
+ <AT91_PIOC 0 AT91_PERIPH_A AT91_PINCTRL_NONE /* SPI0_MISO */
+ AT91_PIOC 1 AT91_PERIPH_A AT91_PINCTRL_NONE /* SPI0_MOSI */
+ AT91_PIOC 2 AT91_PERIPH_A AT91_PINCTRL_NONE /* SPI0_SPCK */
+ >;
+ };
+ };
+
+ ssc0 {
+ pinctrl_ssc0_tx: ssc0_tx {
+ atmel,pins =
+ <AT91_PIOB 27 AT91_PERIPH_B AT91_PINCTRL_NONE /* TK0 */
+ AT91_PIOB 31 AT91_PERIPH_B AT91_PINCTRL_NONE /* TF0 */
+ AT91_PIOB 28 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* TD0 */
+ };
+
+ pinctrl_ssc0_rx: ssc0_rx {
+ atmel,pins =
+ <AT91_PIOB 26 AT91_PERIPH_B AT91_PINCTRL_NONE /* RK0 */
+ AT91_PIOB 30 AT91_PERIPH_B AT91_PINCTRL_NONE /* RF0 */
+ AT91_PIOB 29 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* RD0 */
+ };
+ };
+
+ ssc1 {
+ pinctrl_ssc1_tx: ssc1_tx {
+ atmel,pins =
+ <AT91_PIOC 19 AT91_PERIPH_B AT91_PINCTRL_NONE /* TK1 */
+ AT91_PIOC 20 AT91_PERIPH_B AT91_PINCTRL_NONE /* TF1 */
+ AT91_PIOC 21 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* TD1 */
+ };
+
+ pinctrl_ssc1_rx: ssc1_rx {
+ atmel,pins =
+ <AT91_PIOC 24 AT91_PERIPH_B AT91_PINCTRL_NONE /* RK1 */
+ AT91_PIOC 22 AT91_PERIPH_B AT91_PINCTRL_NONE /* RF1 */
+ AT91_PIOC 23 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* RD1 */
+ };
+ };
+
+ spi1 {
+ pinctrl_spi1: spi1-0 {
+ atmel,pins =
+ <AT91_PIOB 18 AT91_PERIPH_A AT91_PINCTRL_NONE /* SPI1_MISO */
+ AT91_PIOB 19 AT91_PERIPH_A AT91_PINCTRL_NONE /* SPI1_MOSI */
+ AT91_PIOB 20 AT91_PERIPH_A AT91_PINCTRL_NONE /* SPI1_SPCK */
+ >;
+ };
+ };
+
+ spi2 {
+ pinctrl_spi2: spi2-0 {
+ atmel,pins =
+ <AT91_PIOD 11 AT91_PERIPH_B AT91_PINCTRL_NONE /* SPI2_MISO conflicts with RTS0 */
+ AT91_PIOD 13 AT91_PERIPH_B AT91_PINCTRL_NONE /* SPI2_MOSI conflicts with TXD0 */
+ AT91_PIOD 15 AT91_PERIPH_B AT91_PINCTRL_NONE /* SPI2_SPCK conflicts with RTS1 */
+ >;
+ };
+ };
+
+ uart0 {
+ pinctrl_uart0: uart0-0 {
+ atmel,pins =
+ <AT91_PIOE 29 AT91_PERIPH_B AT91_PINCTRL_NONE /* RXD */
+ AT91_PIOE 30 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* TXD */
+ >;
+ };
+ };
+
+ uart1 {
+ pinctrl_uart1: uart1-0 {
+ atmel,pins =
+ <AT91_PIOC 25 AT91_PERIPH_C AT91_PINCTRL_NONE /* RXD */
+ AT91_PIOC 26 AT91_PERIPH_C AT91_PINCTRL_PULL_UP /* TXD */
+ >;
+ };
+ };
+
+ usart0 {
+ pinctrl_usart0: usart0-0 {
+ atmel,pins =
+ <AT91_PIOD 12 AT91_PERIPH_A AT91_PINCTRL_NONE /* RXD */
+ AT91_PIOD 13 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* TXD */
+ >;
+ };
+ pinctrl_usart0_rts: usart0_rts-0 {
+ atmel,pins = <AT91_PIOD 11 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ pinctrl_usart0_cts: usart0_cts-0 {
+ atmel,pins = <AT91_PIOD 10 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ };
+
+ usart1 {
+ pinctrl_usart1: usart1-0 {
+ atmel,pins =
+ <AT91_PIOD 16 AT91_PERIPH_A AT91_PINCTRL_NONE /* RXD */
+ AT91_PIOD 17 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* TXD */
+ >;
+ };
+ pinctrl_usart1_rts: usart1_rts-0 {
+ atmel,pins = <AT91_PIOD 15 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ pinctrl_usart1_cts: usart1_cts-0 {
+ atmel,pins = <AT91_PIOD 14 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ };
+
+ usart2 {
+ pinctrl_usart2: usart2-0 {
+ atmel,pins =
+ <AT91_PIOB 4 AT91_PERIPH_B AT91_PINCTRL_NONE /* RXD - conflicts with G0_CRS, ISI_HSYNC */
+ AT91_PIOB 5 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* TXD - conflicts with G0_COL, PCK2 */
+ >;
+ };
+ pinctrl_usart2_rts: usart2_rts-0 {
+ atmel,pins = <AT91_PIOB 11 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* conflicts with G0_RX3, PWMH1 */
+ };
+ pinctrl_usart2_cts: usart2_cts-0 {
+ atmel,pins = <AT91_PIOB 3 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* conflicts with G0_TXER, ISI_VSYNC */
+ };
+ };
+
+ usart3 {
+ pinctrl_usart3: usart3-0 {
+ atmel,pins =
+ <AT91_PIOE 16 AT91_PERIPH_B AT91_PINCTRL_NONE /* RXD */
+ AT91_PIOE 17 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* TXD */
+ >;
+ };
+ };
+
+ usart4 {
+ pinctrl_usart4: usart4-0 {
+ atmel,pins =
+ <AT91_PIOE 26 AT91_PERIPH_B AT91_PINCTRL_NONE /* RXD */
+ AT91_PIOE 27 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* TXD */
+ >;
+ };
+ pinctrl_usart4_rts: usart4_rts-0 {
+ atmel,pins = <AT91_PIOE 28 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* conflicts with NWAIT, A19 */
+ };
+ pinctrl_usart4_cts: usart4_cts-0 {
+ atmel,pins = <AT91_PIOE 0 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* conflicts with A0/NBS0, MCI0_CDB */
+ };
+ };
+ };
+
+ aic: interrupt-controller at fc06e000 {
+ #interrupt-cells = <3>;
+ compatible = "atmel,sama5d4-aic";
+ interrupt-controller;
+ reg = <0xfc06e000 0x200>;
+ atmel,external-irqs = <56>;
+ };
+ };
+ };
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [U-Boot] [PATCH v1 2/2] ARM: dts: at91: add dts file for sama5d4ek board
2016-10-26 9:03 [U-Boot] [PATCH v1 0/2] ARM: dts: at91: add dts files for the boards of SAMA5D4 Wenyou Yang
2016-10-26 9:03 ` [U-Boot] [PATCH v1 1/2] ARM: dts: at91: add dts file for sama5d4 Xplained board Wenyou Yang
@ 2016-10-26 9:03 ` Wenyou Yang
1 sibling, 0 replies; 3+ messages in thread
From: Wenyou Yang @ 2016-10-26 9:03 UTC (permalink / raw)
To: u-boot
The dts file is copied from the kernel, do the following changes.
- add pinctrl node for the cs pin of spi0.
- fix the compile warning.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
---
arch/arm/dts/Makefile | 3 +
arch/arm/dts/at91-sama5d4ek.dts | 340 ++++++++++++++++++++++++++++++++++++++++
2 files changed, 343 insertions(+)
create mode 100644 arch/arm/dts/at91-sama5d4ek.dts
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 8992636..efae789 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -294,6 +294,9 @@ dtb-$(CONFIG_SOC_KEYSTONE) += k2hk-evm.dtb \
dtb-$(CONFIG_TARGET_SAMA5D2_XPLAINED) += \
at91-sama5d2_xplained.dtb
+dtb-$(CONFIG_TARGET_SAMA5D4EK) += \
+ at91-sama5d4ek.dtb
+
dtb-$(CONFIG_TARGET_SAMA5D4_XPLAINED) += \
at91-sama5d4_xplained.dtb
diff --git a/arch/arm/dts/at91-sama5d4ek.dts b/arch/arm/dts/at91-sama5d4ek.dts
new file mode 100644
index 0000000..501738a
--- /dev/null
+++ b/arch/arm/dts/at91-sama5d4ek.dts
@@ -0,0 +1,340 @@
+/*
+ * at91-sama5d4ek.dts - Device Tree file for SAMA5D4 Evaluation Kit
+ *
+ * Copyright (C) 2014 Atmel,
+ * 2014 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+#include "sama5d4.dtsi"
+
+/ {
+ model = "Atmel SAMA5D4-EK";
+ compatible = "atmel,sama5d4ek", "atmel,sama5d4", "atmel,sama5";
+
+ aliases {
+ spi0 = &spi0;
+ };
+
+ chosen {
+ stdout-path = &usart3;
+ };
+
+
+ memory {
+ reg = <0x20000000 0x20000000>;
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <12000000>;
+ };
+ };
+
+ ahb {
+ apb {
+ adc0: adc at fc034000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ /* external trigger conflicts with USBA_VBUS */
+ &pinctrl_adc0_ad0
+ &pinctrl_adc0_ad1
+ &pinctrl_adc0_ad2
+ &pinctrl_adc0_ad3
+ &pinctrl_adc0_ad4
+ >;
+ /* The vref depends on JP22 of EK. If connect 1-2 then use 3.3V. connect 2-3 use 3.0V */
+ atmel,adc-vref = <3300>;
+ /*atmel,adc-ts-wires = <4>;*/ /* Set up ADC touch screen */
+ status = "okay"; /* Enable ADC IIO support */
+ };
+
+ mmc0: mmc at f8000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
+ slot at 0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioE 5 0>;
+ };
+ };
+
+ ssc0: ssc at f8008000 {
+ status = "okay";
+ };
+
+ spi0: spi at f8010000 {
+ cs-gpios = <&pioC 3 0>, <0>, <0>, <0>;
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi0 &pinctrl_spi0_cs>;
+ m25p80 at 0 {
+ compatible = "atmel,at25df321a";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ };
+ };
+
+ i2c0: i2c at f8014000 {
+ status = "okay";
+
+ wm8904: codec at 1a {
+ compatible = "wlf,wm8904";
+ reg = <0x1a>;
+ clocks = <&pck2>;
+ clock-names = "mclk";
+ };
+
+ qt1070:keyboard at 1b {
+ compatible = "qt1070";
+ reg = <0x1b>;
+ interrupt-parent = <&pioE>;
+ interrupts = <25 0x0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qt1070_irq>;
+ wakeup-source;
+ };
+
+ atmel_mxt_ts at 4c {
+ compatible = "atmel,atmel_mxt_ts";
+ reg = <0x4c>;
+ interrupt-parent = <&pioE>;
+ interrupts = <24 0x0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mxt_ts>;
+ };
+ };
+
+ macb0: ethernet at f8020000 {
+ pinctrl-0 = <&pinctrl_macb0_rmii &pinctrl_macb0_phy_irq>;
+ phy-mode = "rmii";
+ status = "okay";
+
+ ethernet-phy at 1 {
+ reg = <0x1>;
+ interrupt-parent = <&pioE>;
+ interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+ };
+ };
+
+ mmc1: mmc at fc000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
+ status = "okay";
+ slot at 0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioE 6 0>;
+ };
+ };
+
+ usart2: serial at fc008000 {
+ status = "okay";
+ };
+
+ usart3: serial at fc00c000 {
+ status = "okay";
+ };
+
+ usart4: serial at fc010000 {
+ status = "okay";
+ };
+
+ watchdog at fc068640 {
+ status = "okay";
+ };
+
+ pinctrl at fc06a000 {
+ board {
+ pinctrl_macb0_phy_irq: macb0_phy_irq {
+ atmel,pins =
+ <AT91_PIOE 1 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ pinctrl_mmc0_cd: mmc0_cd {
+ atmel,pins =
+ <AT91_PIOE 5 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
+ pinctrl_mmc1_cd: mmc1_cd {
+ atmel,pins =
+ <AT91_PIOE 6 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
+ pinctrl_pck2_as_audio_mck: pck2_as_audio_mck {
+ atmel,pins =
+ <AT91_PIOB 10 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+ pinctrl_usba_vbus: usba_vbus {
+ atmel,pins =
+ <AT91_PIOE 31 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+ };
+ pinctrl_key_gpio: key_gpio_0 {
+ atmel,pins =
+ <AT91_PIOE 13 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PE13 gpio */
+ };
+ pinctrl_qt1070_irq: qt1070_irq {
+ atmel,pins =
+ <AT91_PIOE 25 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
+ pinctrl_mxt_ts: mxt_irq {
+ atmel,pins =
+ <AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
+ pinctrl_spi0_cs: spi0_cs {
+ atmel,pins =
+ <AT91_PIOC 3 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(1))>;
+ };
+ };
+ };
+ };
+
+ usb0: gadget at 00400000 {
+ atmel,vbus-gpio = <&pioE 31 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ status = "okay";
+ };
+
+ usb1: ohci at 00500000 {
+ num-ports = <3>;
+ atmel,vbus-gpio = <0 /* &pioE 10 GPIO_ACTIVE_LOW */
+ &pioE 11 GPIO_ACTIVE_LOW
+ &pioE 12 GPIO_ACTIVE_LOW
+ >;
+ status = "okay";
+ };
+
+ usb2: ehci at 00600000 {
+ status = "okay";
+ };
+
+ nand0: nand at 80000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ nand-on-flash-bbt;
+ atmel,has-pmecc;
+ status = "okay";
+
+ at91bootstrap at 0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ bootloader at 40000 {
+ label = "bootloader";
+ reg = <0x40000 0x80000>;
+ };
+
+ bootloaderenv at c0000 {
+ label = "bootloader env";
+ reg = <0xc0000 0xc0000>;
+ };
+
+ dtb at 180000 {
+ label = "device tree";
+ reg = <0x180000 0x80000>;
+ };
+
+ kernel at 200000 {
+ label = "kernel";
+ reg = <0x200000 0x600000>;
+ };
+
+ rootfs at 800000 {
+ label = "rootfs";
+ reg = <0x800000 0x0f800000>;
+ };
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_key_gpio>;
+
+ pb_user1 {
+ label = "pb_user1";
+ gpios = <&pioE 13 GPIO_ACTIVE_HIGH>;
+ linux,code = <0x100>;
+ wakeup-source;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ status = "okay";
+
+ d8 {
+ label = "d8";
+ /* PE28, conflicts with usart4 rts pin */
+ gpios = <&pioE 28 GPIO_ACTIVE_LOW>;
+ };
+
+ d9 {
+ label = "d9";
+ gpios = <&pioE 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ d10 {
+ label = "d10";
+ gpios = <&pioE 8 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ sound {
+ compatible = "atmel,asoc-wm8904";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pck2_as_audio_mck>;
+
+ atmel,model = "wm8904 @ SAMA5D4EK";
+ atmel,audio-routing =
+ "Headphone Jack", "HPOUTL",
+ "Headphone Jack", "HPOUTR",
+ "IN1L", "Line In Jack",
+ "IN1R", "Line In Jack";
+
+ atmel,ssc-controller = <&ssc0>;
+ atmel,audio-codec = <&wm8904>;
+ };
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 3+ messages in thread
end of thread, other threads:[~2016-10-26 9:03 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-10-26 9:03 [U-Boot] [PATCH v1 0/2] ARM: dts: at91: add dts files for the boards of SAMA5D4 Wenyou Yang
2016-10-26 9:03 ` [U-Boot] [PATCH v1 1/2] ARM: dts: at91: add dts file for sama5d4 Xplained board Wenyou Yang
2016-10-26 9:03 ` [U-Boot] [PATCH v1 2/2] ARM: dts: at91: add dts file for sama5d4ek board Wenyou Yang
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.