* [PATCH v6 1/5] mmc: dt-bindings: add ZTE ZX296718 MMC bindings
2016-11-18 6:29 ` [PATCH v6 0/5] Add intial support to DW MMC host on ZTE SoC Jun Nie
@ 2016-11-18 6:29 ` Jun Nie
2016-11-21 1:26 ` Jun Nie
2016-11-24 2:17 ` Jun Nie
2016-11-18 6:29 ` [PATCH v6 2/5] mmc: zx: Initial support for ZX mmc controller Jun Nie
` (4 subsequent siblings)
5 siblings, 2 replies; 16+ messages in thread
From: Jun Nie @ 2016-11-18 6:29 UTC (permalink / raw)
To: shawn.guo, xie.baoyou
Cc: ulf.hansson, jh80.chung, jason.liu, chen.chaokai, lai.binz,
linux-mmc, Jun Nie
Document the device-tree binding of ZTE MMC host on
ZX296718 SoC.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
---
.../devicetree/bindings/mmc/zx-dw-mshc.txt | 35 ++++++++++++++++++++++
1 file changed, 35 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
diff --git a/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
new file mode 100644
index 0000000..c175c4b
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
@@ -0,0 +1,35 @@
+* ZTE specific extensions to the Synopsys Designware Mobile Storage
+ Host Controller
+
+The Synopsys designware mobile storage host controller is used to interface
+a SoC with storage medium such as eMMC or SD/MMC cards. This file documents
+differences between the core Synopsys dw mshc controller properties described
+by synopsys-dw-mshc.txt and the properties used by the ZTE specific
+extensions to the Synopsys Designware Mobile Storage Host Controller.
+
+Required Properties:
+
+* compatible: should be
+ - "zte,zx296718-dw-mshc": for ZX SoCs
+
+Example:
+
+ mmc1: mmc@1110000 {
+ compatible = "zte,zx296718-dw-mshc";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x01110000 0x1000>;
+ interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ fifo-depth = <32>;
+ data-addr = <0x200>;
+ fifo-watermark-aligned;
+ bus-width = <4>;
+ clock-frequency = <50000000>;
+ clocks = <&topcrm SD0_AHB>, <&topcrm SD0_WCLK>;
+ clock-names = "biu", "ciu";
+ num-slots = <1>;
+ max-frequency = <50000000>;
+ cap-sdio-irq;
+ cap-sd-highspeed;
+ status = "disabled";
+ };
--
1.9.1
^ permalink raw reply related [flat|nested] 16+ messages in thread* Re: [PATCH v6 1/5] mmc: dt-bindings: add ZTE ZX296718 MMC bindings
2016-11-18 6:29 ` [PATCH v6 1/5] mmc: dt-bindings: add ZTE ZX296718 MMC bindings Jun Nie
@ 2016-11-21 1:26 ` Jun Nie
2016-11-24 2:17 ` Jun Nie
1 sibling, 0 replies; 16+ messages in thread
From: Jun Nie @ 2016-11-21 1:26 UTC (permalink / raw)
To: Shawn Guo, xie.baoyou, Rob Herring, mark.rutland
Cc: Ulf Hansson, Jaehoon Chung, Jason Liu, chen.chaokai, lai.binz,
linux-mmc, Jun Nie, devicetree
2016-11-18 14:29 GMT+08:00 Jun Nie <jun.nie@linaro.org>:
> Document the device-tree binding of ZTE MMC host on
> ZX296718 SoC.
>
> Signed-off-by: Jun Nie <jun.nie@linaro.org>
> ---
> .../devicetree/bindings/mmc/zx-dw-mshc.txt | 35 ++++++++++++++++++++++
> 1 file changed, 35 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
>
> diff --git a/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
> new file mode 100644
> index 0000000..c175c4b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
> @@ -0,0 +1,35 @@
> +* ZTE specific extensions to the Synopsys Designware Mobile Storage
> + Host Controller
> +
> +The Synopsys designware mobile storage host controller is used to interface
> +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents
> +differences between the core Synopsys dw mshc controller properties described
> +by synopsys-dw-mshc.txt and the properties used by the ZTE specific
> +extensions to the Synopsys Designware Mobile Storage Host Controller.
> +
> +Required Properties:
> +
> +* compatible: should be
> + - "zte,zx296718-dw-mshc": for ZX SoCs
> +
> +Example:
> +
> + mmc1: mmc@1110000 {
> + compatible = "zte,zx296718-dw-mshc";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x01110000 0x1000>;
> + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
> + fifo-depth = <32>;
> + data-addr = <0x200>;
> + fifo-watermark-aligned;
> + bus-width = <4>;
> + clock-frequency = <50000000>;
> + clocks = <&topcrm SD0_AHB>, <&topcrm SD0_WCLK>;
> + clock-names = "biu", "ciu";
> + num-slots = <1>;
> + max-frequency = <50000000>;
> + cap-sdio-irq;
> + cap-sd-highspeed;
> + status = "disabled";
> + };
> --
> 1.9.1
>
Add DT maintainer to review and act. Thank you!
Jun
^ permalink raw reply [flat|nested] 16+ messages in thread* Re: [PATCH v6 1/5] mmc: dt-bindings: add ZTE ZX296718 MMC bindings
2016-11-18 6:29 ` [PATCH v6 1/5] mmc: dt-bindings: add ZTE ZX296718 MMC bindings Jun Nie
2016-11-21 1:26 ` Jun Nie
@ 2016-11-24 2:17 ` Jun Nie
2016-12-01 1:34 ` Jun Nie
1 sibling, 1 reply; 16+ messages in thread
From: Jun Nie @ 2016-11-24 2:17 UTC (permalink / raw)
To: Shawn Guo, xie.baoyou, Rob Herring, mark.rutland
Cc: Ulf Hansson, Jaehoon Chung, Jason Liu, chen.chaokai, lai.binz,
linux-mmc, Jun Nie, devicetree
2016-11-18 14:29 GMT+08:00 Jun Nie <jun.nie@linaro.org>:
> Document the device-tree binding of ZTE MMC host on
> ZX296718 SoC.
>
> Signed-off-by: Jun Nie <jun.nie@linaro.org>
> ---
> .../devicetree/bindings/mmc/zx-dw-mshc.txt | 35 ++++++++++++++++++++++
> 1 file changed, 35 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
>
> diff --git a/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
> new file mode 100644
> index 0000000..c175c4b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
> @@ -0,0 +1,35 @@
> +* ZTE specific extensions to the Synopsys Designware Mobile Storage
> + Host Controller
> +
> +The Synopsys designware mobile storage host controller is used to interface
> +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents
> +differences between the core Synopsys dw mshc controller properties described
> +by synopsys-dw-mshc.txt and the properties used by the ZTE specific
> +extensions to the Synopsys Designware Mobile Storage Host Controller.
> +
> +Required Properties:
> +
> +* compatible: should be
> + - "zte,zx296718-dw-mshc": for ZX SoCs
> +
> +Example:
> +
> + mmc1: mmc@1110000 {
> + compatible = "zte,zx296718-dw-mshc";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x01110000 0x1000>;
> + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
> + fifo-depth = <32>;
> + data-addr = <0x200>;
> + fifo-watermark-aligned;
> + bus-width = <4>;
> + clock-frequency = <50000000>;
> + clocks = <&topcrm SD0_AHB>, <&topcrm SD0_WCLK>;
> + clock-names = "biu", "ciu";
> + num-slots = <1>;
> + max-frequency = <50000000>;
> + cap-sdio-irq;
> + cap-sd-highspeed;
> + status = "disabled";
> + };
> --
> 1.9.1
>
Hi Rob & Mark,
Could you help review and act this patch if you think it is OK? Thank you!
Jun
^ permalink raw reply [flat|nested] 16+ messages in thread* Re: [PATCH v6 1/5] mmc: dt-bindings: add ZTE ZX296718 MMC bindings
2016-11-24 2:17 ` Jun Nie
@ 2016-12-01 1:34 ` Jun Nie
2016-12-01 13:45 ` Rob Herring
0 siblings, 1 reply; 16+ messages in thread
From: Jun Nie @ 2016-12-01 1:34 UTC (permalink / raw)
To: Shawn Guo, xie.baoyou, Rob Herring, mark.rutland
Cc: Ulf Hansson, Jaehoon Chung, Jason Liu, chen.chaokai, lai.binz,
linux-mmc, Jun Nie, devicetree
2016-11-24 10:17 GMT+08:00 Jun Nie <jun.nie@linaro.org>:
> 2016-11-18 14:29 GMT+08:00 Jun Nie <jun.nie@linaro.org>:
>> Document the device-tree binding of ZTE MMC host on
>> ZX296718 SoC.
>>
>> Signed-off-by: Jun Nie <jun.nie@linaro.org>
>> ---
>> .../devicetree/bindings/mmc/zx-dw-mshc.txt | 35 ++++++++++++++++++++++
>> 1 file changed, 35 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
>>
>> diff --git a/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
>> new file mode 100644
>> index 0000000..c175c4b
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
>> @@ -0,0 +1,35 @@
>> +* ZTE specific extensions to the Synopsys Designware Mobile Storage
>> + Host Controller
>> +
>> +The Synopsys designware mobile storage host controller is used to interface
>> +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents
>> +differences between the core Synopsys dw mshc controller properties described
>> +by synopsys-dw-mshc.txt and the properties used by the ZTE specific
>> +extensions to the Synopsys Designware Mobile Storage Host Controller.
>> +
>> +Required Properties:
>> +
>> +* compatible: should be
>> + - "zte,zx296718-dw-mshc": for ZX SoCs
>> +
>> +Example:
>> +
>> + mmc1: mmc@1110000 {
>> + compatible = "zte,zx296718-dw-mshc";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + reg = <0x01110000 0x1000>;
>> + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
>> + fifo-depth = <32>;
>> + data-addr = <0x200>;
>> + fifo-watermark-aligned;
>> + bus-width = <4>;
>> + clock-frequency = <50000000>;
>> + clocks = <&topcrm SD0_AHB>, <&topcrm SD0_WCLK>;
>> + clock-names = "biu", "ciu";
>> + num-slots = <1>;
>> + max-frequency = <50000000>;
>> + cap-sdio-irq;
>> + cap-sd-highspeed;
>> + status = "disabled";
>> + };
>> --
>> 1.9.1
>>
>
> Hi Rob & Mark,
>
> Could you help review and act this patch if you think it is OK? Thank you!
>
> Jun
Hi Rob & Mark,
Could you help comment or act on this patch? Thank you!
Jun
^ permalink raw reply [flat|nested] 16+ messages in thread* Re: [PATCH v6 1/5] mmc: dt-bindings: add ZTE ZX296718 MMC bindings
2016-12-01 1:34 ` Jun Nie
@ 2016-12-01 13:45 ` Rob Herring
0 siblings, 0 replies; 16+ messages in thread
From: Rob Herring @ 2016-12-01 13:45 UTC (permalink / raw)
To: Jun Nie
Cc: Shawn Guo, xie.baoyou, Mark Rutland, Ulf Hansson, Jaehoon Chung,
Jason Liu, chen.chaokai, lai.binz, linux-mmc, devicetree
On Wed, Nov 30, 2016 at 7:34 PM, Jun Nie <jun.nie@linaro.org> wrote:
> 2016-11-24 10:17 GMT+08:00 Jun Nie <jun.nie@linaro.org>:
>> 2016-11-18 14:29 GMT+08:00 Jun Nie <jun.nie@linaro.org>:
>>> Document the device-tree binding of ZTE MMC host on
>>> ZX296718 SoC.
>>>
>>> Signed-off-by: Jun Nie <jun.nie@linaro.org>
>>> ---
>>> .../devicetree/bindings/mmc/zx-dw-mshc.txt | 35 ++++++++++++++++++++++
>>> 1 file changed, 35 insertions(+)
>>> create mode 100644 Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
>>>
>>> diff --git a/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
>>> new file mode 100644
>>> index 0000000..c175c4b
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
>>> @@ -0,0 +1,35 @@
>>> +* ZTE specific extensions to the Synopsys Designware Mobile Storage
>>> + Host Controller
>>> +
>>> +The Synopsys designware mobile storage host controller is used to interface
>>> +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents
>>> +differences between the core Synopsys dw mshc controller properties described
>>> +by synopsys-dw-mshc.txt and the properties used by the ZTE specific
>>> +extensions to the Synopsys Designware Mobile Storage Host Controller.
>>> +
>>> +Required Properties:
>>> +
>>> +* compatible: should be
>>> + - "zte,zx296718-dw-mshc": for ZX SoCs
>>> +
>>> +Example:
>>> +
>>> + mmc1: mmc@1110000 {
>>> + compatible = "zte,zx296718-dw-mshc";
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> + reg = <0x01110000 0x1000>;
>>> + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
>>> + fifo-depth = <32>;
>>> + data-addr = <0x200>;
>>> + fifo-watermark-aligned;
>>> + bus-width = <4>;
>>> + clock-frequency = <50000000>;
>>> + clocks = <&topcrm SD0_AHB>, <&topcrm SD0_WCLK>;
>>> + clock-names = "biu", "ciu";
>>> + num-slots = <1>;
>>> + max-frequency = <50000000>;
>>> + cap-sdio-irq;
>>> + cap-sd-highspeed;
>>> + status = "disabled";
>>> + };
>>> --
>>> 1.9.1
>>>
>>
>> Hi Rob & Mark,
>>
>> Could you help review and act this patch if you think it is OK? Thank you!
>>
>> Jun
>
> Hi Rob & Mark,
>
> Could you help comment or act on this patch? Thank you!
Resend the patch to the DT list so patchwork will pick it up if you
want it reviewed.
Rob
^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v6 2/5] mmc: zx: Initial support for ZX mmc controller
2016-11-18 6:29 ` [PATCH v6 0/5] Add intial support to DW MMC host on ZTE SoC Jun Nie
2016-11-18 6:29 ` [PATCH v6 1/5] mmc: dt-bindings: add ZTE ZX296718 MMC bindings Jun Nie
@ 2016-11-18 6:29 ` Jun Nie
2016-11-18 6:29 ` [PATCH v6 3/5] Documentation: synopsys-dw-mshc: add binding for fifo quirks Jun Nie
` (3 subsequent siblings)
5 siblings, 0 replies; 16+ messages in thread
From: Jun Nie @ 2016-11-18 6:29 UTC (permalink / raw)
To: shawn.guo, xie.baoyou
Cc: ulf.hansson, jh80.chung, jason.liu, chen.chaokai, lai.binz,
linux-mmc, Jun Nie
This platform driver adds initial support for the DW host controller
found on ZTE SoCs.
It has been tested on ZX296718 EVB board currently. More support on
timing tuning will be added when hardware is available.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
---
drivers/mmc/host/Kconfig | 9 ++
drivers/mmc/host/Makefile | 1 +
drivers/mmc/host/dw_mmc-zx.c | 242 +++++++++++++++++++++++++++++++++++++++++++
drivers/mmc/host/dw_mmc-zx.h | 31 ++++++
4 files changed, 283 insertions(+)
create mode 100644 drivers/mmc/host/dw_mmc-zx.c
create mode 100644 drivers/mmc/host/dw_mmc-zx.h
diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index 5274f50..4dafbc2 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -662,6 +662,15 @@ config MMC_DW_ROCKCHIP
Synopsys DesignWare Memory Card Interface driver. Select this option
for platforms based on RK3066, RK3188 and RK3288 SoC's.
+config MMC_DW_ZX
+ tristate "ZTE specific extensions for Synopsys DW Memory Card Interface"
+ depends on MMC_DW && ARCH_ZX
+ select MMC_DW_PLTFM
+ help
+ This selects support for ZTE SoC specific extensions to the
+ Synopsys DesignWare Memory Card Interface driver. Select this option
+ for platforms based on ZX296718 SoC's.
+
config MMC_SH_MMCIF
tristate "SuperH Internal MMCIF support"
depends on HAS_DMA
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index e2bdaaf..9766143 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -48,6 +48,7 @@ obj-$(CONFIG_MMC_DW_EXYNOS) += dw_mmc-exynos.o
obj-$(CONFIG_MMC_DW_K3) += dw_mmc-k3.o
obj-$(CONFIG_MMC_DW_PCI) += dw_mmc-pci.o
obj-$(CONFIG_MMC_DW_ROCKCHIP) += dw_mmc-rockchip.o
+obj-$(CONFIG_MMC_DW_ZX) += dw_mmc-zx.o
obj-$(CONFIG_MMC_SH_MMCIF) += sh_mmcif.o
obj-$(CONFIG_MMC_JZ4740) += jz4740_mmc.o
obj-$(CONFIG_MMC_VUB300) += vub300.o
diff --git a/drivers/mmc/host/dw_mmc-zx.c b/drivers/mmc/host/dw_mmc-zx.c
new file mode 100644
index 0000000..11b9fc3
--- /dev/null
+++ b/drivers/mmc/host/dw_mmc-zx.c
@@ -0,0 +1,242 @@
+/*
+ * ZX Specific Extensions for Synopsys DW Multimedia Card Interface driver
+ *
+ * Copyright (C) 2016, Linaro Ltd.
+ * Copyright (C) 2016, ZTE Corp.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/clk.h>
+#include <linux/mfd/syscon.h>
+#include <linux/mmc/dw_mmc.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/mmc.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+#include "dw_mmc.h"
+#include "dw_mmc-pltfm.h"
+#include "dw_mmc-zx.h"
+
+struct dw_mci_zx_priv_data {
+ struct regmap *sysc_base;
+};
+
+enum delay_type {
+ DELAY_TYPE_READ, /* read dqs delay */
+ DELAY_TYPE_CLK, /* clk sample delay */
+};
+
+static int dw_mci_zx_emmc_set_delay(struct dw_mci *host, unsigned int delay,
+ enum delay_type dflag)
+{
+ struct dw_mci_zx_priv_data *priv = host->priv;
+ struct regmap *sysc_base = priv->sysc_base;
+ unsigned int clksel;
+ unsigned int loop = 1000;
+ int ret;
+
+ if (!sysc_base)
+ return -EINVAL;
+
+ ret = regmap_update_bits(sysc_base, LB_AON_EMMC_CFG_REG0,
+ PARA_HALF_CLK_MODE | PARA_DLL_BYPASS_MODE |
+ PARA_PHASE_DET_SEL_MASK |
+ PARA_DLL_LOCK_NUM_MASK |
+ DLL_REG_SET | PARA_DLL_START_MASK,
+ PARA_DLL_START(4) | PARA_DLL_LOCK_NUM(4));
+ if (ret)
+ return ret;
+
+ ret = regmap_read(sysc_base, LB_AON_EMMC_CFG_REG1, &clksel);
+ if (ret)
+ return ret;
+
+ if (dflag == DELAY_TYPE_CLK) {
+ clksel &= ~CLK_SAMP_DELAY_MASK;
+ clksel |= CLK_SAMP_DELAY(delay);
+ } else {
+ clksel &= ~READ_DQS_DELAY_MASK;
+ clksel |= READ_DQS_DELAY(delay);
+ }
+
+ regmap_write(sysc_base, LB_AON_EMMC_CFG_REG1, clksel);
+ regmap_update_bits(sysc_base, LB_AON_EMMC_CFG_REG0,
+ PARA_DLL_START_MASK | PARA_DLL_LOCK_NUM_MASK |
+ DLL_REG_SET,
+ PARA_DLL_START(4) | PARA_DLL_LOCK_NUM(4) |
+ DLL_REG_SET);
+
+ do {
+ ret = regmap_read(sysc_base, LB_AON_EMMC_CFG_REG2, &clksel);
+ if (ret)
+ return ret;
+
+ } while (--loop && !(clksel & ZX_DLL_LOCKED));
+
+ if (!loop) {
+ dev_err(host->dev, "Error: %s dll lock fail\n", __func__);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static int dw_mci_zx_emmc_execute_tuning(struct dw_mci_slot *slot, u32 opcode)
+{
+ struct dw_mci *host = slot->host;
+ struct mmc_host *mmc = slot->mmc;
+ int ret, len, start = 0, end = 0, delay, best = 0;
+
+ for (delay = 1 ; delay < 128; delay++) {
+ ret = dw_mci_zx_emmc_set_delay(host, delay, DELAY_TYPE_CLK);
+ if (!ret && mmc_send_tuning(mmc, opcode, NULL)) {
+ if (start >= 0) {
+ end = delay - 1;
+ /* check and update longest good range */
+ if ((end - start) > len) {
+ best = (start + end) >> 1;
+ len = end - start;
+ }
+ }
+ start = -1;
+ end = 0;
+ continue;
+ }
+ if (start < 0)
+ start = delay;
+ }
+
+ if (start >= 0) {
+ end = delay - 1;
+ if ((end - start) > len) {
+ best = (start + end) >> 1;
+ len = end - start;
+ }
+ }
+ if (best < 0)
+ return -EIO;
+
+ dev_info(host->dev, "%s best range: start %d end %d\n", __func__,
+ start, end);
+ return dw_mci_zx_emmc_set_delay(host, best, DELAY_TYPE_CLK);
+}
+
+static int dw_mci_zx_prepare_hs400_tuning(struct dw_mci *host,
+ struct mmc_ios *ios)
+{
+ int ret;
+
+ /* config phase shift as 90 degree */
+ ret = dw_mci_zx_emmc_set_delay(host, 32, DELAY_TYPE_READ);
+ if (ret < 0)
+ return -EIO;
+
+ return 0;
+}
+
+static int dw_mci_zx_execute_tuning(struct dw_mci_slot *slot, u32 opcode)
+{
+ struct dw_mci *host = slot->host;
+
+ if (host->verid == 0x290a) /* only for emmc */
+ return dw_mci_zx_emmc_execute_tuning(slot, opcode);
+ /* TODO: Add 0x210a dedicated tuning for sd/sdio */
+
+ return 0;
+}
+
+static int dw_mci_zx_parse_dt(struct dw_mci *host)
+{
+ struct device_node *np = host->dev->of_node;
+ struct device_node *node;
+ struct dw_mci_zx_priv_data *priv;
+ struct regmap *sysc_base;
+ int ret;
+
+ /* syscon is needed only by emmc */
+ node = of_parse_phandle(np, "zte,aon-syscon", 0);
+ if (node) {
+ sysc_base = syscon_node_to_regmap(node);
+ of_node_put(node);
+
+ if (IS_ERR(sysc_base)) {
+ ret = PTR_ERR(sysc_base);
+ if (ret != -EPROBE_DEFER)
+ dev_err(host->dev, "Can't get syscon: %d\n",
+ ret);
+ return ret;
+ }
+ } else {
+ return 0;
+ }
+
+ priv = devm_kzalloc(host->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+ priv->sysc_base = sysc_base;
+ host->priv = priv;
+
+ return 0;
+}
+
+static unsigned long zx_dwmmc_caps[3] = {
+ MMC_CAP_CMD23,
+ MMC_CAP_CMD23,
+ MMC_CAP_CMD23,
+};
+
+static const struct dw_mci_drv_data zx_drv_data = {
+ .caps = zx_dwmmc_caps,
+ .execute_tuning = dw_mci_zx_execute_tuning,
+ .prepare_hs400_tuning = dw_mci_zx_prepare_hs400_tuning,
+ .parse_dt = dw_mci_zx_parse_dt,
+};
+
+static const struct of_device_id dw_mci_zx_match[] = {
+ { .compatible = "zte,zx296718-dw-mshc", .data = &zx_drv_data},
+ {},
+};
+MODULE_DEVICE_TABLE(of, dw_mci_zx_match);
+
+static int dw_mci_zx_probe(struct platform_device *pdev)
+{
+ const struct dw_mci_drv_data *drv_data;
+ const struct of_device_id *match;
+
+ match = of_match_node(dw_mci_zx_match, pdev->dev.of_node);
+ drv_data = match->data;
+
+ return dw_mci_pltfm_register(pdev, drv_data);
+}
+
+static const struct dev_pm_ops dw_mci_zx_dev_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
+ pm_runtime_force_resume)
+ SET_RUNTIME_PM_OPS(dw_mci_runtime_suspend,
+ dw_mci_runtime_resume,
+ NULL)
+};
+
+static struct platform_driver dw_mci_zx_pltfm_driver = {
+ .probe = dw_mci_zx_probe,
+ .remove = dw_mci_pltfm_remove,
+ .driver = {
+ .name = "dwmmc_zx",
+ .of_match_table = dw_mci_zx_match,
+ .pm = &dw_mci_zx_dev_pm_ops,
+ },
+};
+
+module_platform_driver(dw_mci_zx_pltfm_driver);
+
+MODULE_DESCRIPTION("ZTE emmc/sd driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/mmc/host/dw_mmc-zx.h b/drivers/mmc/host/dw_mmc-zx.h
new file mode 100644
index 0000000..f369997
--- /dev/null
+++ b/drivers/mmc/host/dw_mmc-zx.h
@@ -0,0 +1,31 @@
+#ifndef _DW_MMC_ZX_H_
+#define _DW_MMC_ZX_H_
+
+/* ZX296718 SoC specific DLL register offset. */
+#define LB_AON_EMMC_CFG_REG0 0x1B0
+#define LB_AON_EMMC_CFG_REG1 0x1B4
+#define LB_AON_EMMC_CFG_REG2 0x1B8
+
+/* LB_AON_EMMC_CFG_REG0 register defines */
+#define PARA_DLL_START(x) ((x) & 0xFF)
+#define PARA_DLL_START_MASK 0xFF
+#define DLL_REG_SET BIT(8)
+#define PARA_DLL_LOCK_NUM(x) (((x) & 7) << 16)
+#define PARA_DLL_LOCK_NUM_MASK (7 << 16)
+#define PARA_PHASE_DET_SEL(x) (((x) & 7) << 20)
+#define PARA_PHASE_DET_SEL_MASK (7 << 20)
+#define PARA_DLL_BYPASS_MODE BIT(23)
+#define PARA_HALF_CLK_MODE BIT(24)
+
+/* LB_AON_EMMC_CFG_REG1 register defines */
+#define READ_DQS_DELAY(x) ((x) & 0x7F)
+#define READ_DQS_DELAY_MASK (0x7F)
+#define READ_DQS_BYPASS_MODE BIT(7)
+#define CLK_SAMP_DELAY(x) (((x) & 0x7F) << 8)
+#define CLK_SAMP_DELAY_MASK (0x7F << 8)
+#define CLK_SAMP_BYPASS_MODE BIT(15)
+
+/* LB_AON_EMMC_CFG_REG2 register defines */
+#define ZX_DLL_LOCKED BIT(2)
+
+#endif /* _DW_MMC_ZX_H_ */
--
1.9.1
^ permalink raw reply related [flat|nested] 16+ messages in thread* [PATCH v6 3/5] Documentation: synopsys-dw-mshc: add binding for fifo quirks
2016-11-18 6:29 ` [PATCH v6 0/5] Add intial support to DW MMC host on ZTE SoC Jun Nie
2016-11-18 6:29 ` [PATCH v6 1/5] mmc: dt-bindings: add ZTE ZX296718 MMC bindings Jun Nie
2016-11-18 6:29 ` [PATCH v6 2/5] mmc: zx: Initial support for ZX mmc controller Jun Nie
@ 2016-11-18 6:29 ` Jun Nie
2016-11-21 1:28 ` Jun Nie
2016-11-24 2:19 ` Jun Nie
2016-11-18 6:29 ` [PATCH v6 4/5] mmc: dw: Add fifo address property Jun Nie
` (2 subsequent siblings)
5 siblings, 2 replies; 16+ messages in thread
From: Jun Nie @ 2016-11-18 6:29 UTC (permalink / raw)
To: shawn.guo, xie.baoyou
Cc: ulf.hansson, jh80.chung, jason.liu, chen.chaokai, lai.binz,
linux-mmc, Jun Nie
Add fifo-addr property and fifo-watermark-quirk property to
synopsys-dw-mshc bindings. It is intended to provide more
dt interface to support SoCs specific configuration.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
---
Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt | 13 +++++++++++++
1 file changed, 13 insertions(+)
diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
index 4e00e85..8bf2e41 100644
--- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
+++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
@@ -76,6 +76,17 @@ Optional properties:
* broken-cd: as documented in mmc core bindings.
+* data-addr: Override fifo address with value provided by DT. The default FIFO reg
+ offset is assumed as 0x100 (version < 0x240A) and 0x200(version >= 0x240A) by
+ driver. If the controller does not follow this rule, please use this property
+ to set fifo address in device tree.
+
+* fifo-watermark-aligned: Data done irq is expected if data length is less than
+ watermark in PIO mode. But fifo watermark is requested to be aligned with data
+ length in some SoC so that TX/RX irq can be generated with data done irq. Add this
+ watermark quirk to mark this requirement and force fifo watermark setting
+ accordingly.
+
* vmmc-supply: The phandle to the regulator to use for vmmc. If this is
specified we'll defer probe until we can find this regulator.
@@ -103,6 +114,8 @@ board specific portions as listed below.
interrupts = <0 75 0>;
#address-cells = <1>;
#size-cells = <0>;
+ data-addr = <0x200>;
+ fifo-watermark-aligned;
};
[board specific internal DMA resources]
--
1.9.1
^ permalink raw reply related [flat|nested] 16+ messages in thread* Re: [PATCH v6 3/5] Documentation: synopsys-dw-mshc: add binding for fifo quirks
2016-11-18 6:29 ` [PATCH v6 3/5] Documentation: synopsys-dw-mshc: add binding for fifo quirks Jun Nie
@ 2016-11-21 1:28 ` Jun Nie
2016-11-24 2:19 ` Jun Nie
1 sibling, 0 replies; 16+ messages in thread
From: Jun Nie @ 2016-11-21 1:28 UTC (permalink / raw)
To: Shawn Guo, xie.baoyou, Rob Herring, mark.rutland
Cc: Ulf Hansson, Jaehoon Chung, Jason Liu, chen.chaokai, lai.binz,
linux-mmc, Jun Nie, devicetree
2016-11-18 14:29 GMT+08:00 Jun Nie <jun.nie@linaro.org>:
> Add fifo-addr property and fifo-watermark-quirk property to
> synopsys-dw-mshc bindings. It is intended to provide more
> dt interface to support SoCs specific configuration.
>
> Signed-off-by: Jun Nie <jun.nie@linaro.org>
> ---
> Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt | 13 +++++++++++++
> 1 file changed, 13 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
> index 4e00e85..8bf2e41 100644
> --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
> +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
> @@ -76,6 +76,17 @@ Optional properties:
>
> * broken-cd: as documented in mmc core bindings.
>
> +* data-addr: Override fifo address with value provided by DT. The default FIFO reg
> + offset is assumed as 0x100 (version < 0x240A) and 0x200(version >= 0x240A) by
> + driver. If the controller does not follow this rule, please use this property
> + to set fifo address in device tree.
> +
> +* fifo-watermark-aligned: Data done irq is expected if data length is less than
> + watermark in PIO mode. But fifo watermark is requested to be aligned with data
> + length in some SoC so that TX/RX irq can be generated with data done irq. Add this
> + watermark quirk to mark this requirement and force fifo watermark setting
> + accordingly.
> +
> * vmmc-supply: The phandle to the regulator to use for vmmc. If this is
> specified we'll defer probe until we can find this regulator.
>
> @@ -103,6 +114,8 @@ board specific portions as listed below.
> interrupts = <0 75 0>;
> #address-cells = <1>;
> #size-cells = <0>;
> + data-addr = <0x200>;
> + fifo-watermark-aligned;
> };
>
> [board specific internal DMA resources]
> --
> 1.9.1
>
Add DT maintainer to review and act. Thank you!
Jun
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v6 3/5] Documentation: synopsys-dw-mshc: add binding for fifo quirks
2016-11-18 6:29 ` [PATCH v6 3/5] Documentation: synopsys-dw-mshc: add binding for fifo quirks Jun Nie
2016-11-21 1:28 ` Jun Nie
@ 2016-11-24 2:19 ` Jun Nie
[not found] ` <CABymUCN_+kJC2NZaPuqOg1C_Q2ASmiGwbwWCtfiLjGwSqPjgkQ-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
1 sibling, 1 reply; 16+ messages in thread
From: Jun Nie @ 2016-11-24 2:19 UTC (permalink / raw)
To: Shawn Guo, xie.baoyou, Rob Herring, mark.rutland
Cc: Ulf Hansson, Jaehoon Chung, Jason Liu, chen.chaokai, lai.binz,
linux-mmc, Jun Nie, devicetree
2016-11-18 14:29 GMT+08:00 Jun Nie <jun.nie@linaro.org>:
> Add fifo-addr property and fifo-watermark-quirk property to
> synopsys-dw-mshc bindings. It is intended to provide more
> dt interface to support SoCs specific configuration.
>
> Signed-off-by: Jun Nie <jun.nie@linaro.org>
> ---
> Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt | 13 +++++++++++++
> 1 file changed, 13 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
> index 4e00e85..8bf2e41 100644
> --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
> +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
> @@ -76,6 +76,17 @@ Optional properties:
>
> * broken-cd: as documented in mmc core bindings.
>
> +* data-addr: Override fifo address with value provided by DT. The default FIFO reg
> + offset is assumed as 0x100 (version < 0x240A) and 0x200(version >= 0x240A) by
> + driver. If the controller does not follow this rule, please use this property
> + to set fifo address in device tree.
> +
> +* fifo-watermark-aligned: Data done irq is expected if data length is less than
> + watermark in PIO mode. But fifo watermark is requested to be aligned with data
> + length in some SoC so that TX/RX irq can be generated with data done irq. Add this
> + watermark quirk to mark this requirement and force fifo watermark setting
> + accordingly.
> +
> * vmmc-supply: The phandle to the regulator to use for vmmc. If this is
> specified we'll defer probe until we can find this regulator.
>
> @@ -103,6 +114,8 @@ board specific portions as listed below.
> interrupts = <0 75 0>;
> #address-cells = <1>;
> #size-cells = <0>;
> + data-addr = <0x200>;
> + fifo-watermark-aligned;
> };
>
> [board specific internal DMA resources]
> --
> 1.9.1
>
Hi Rob & Mark,
Could you help review and act this patch if you think it is OK? Thank you!
Jun
^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v6 4/5] mmc: dw: Add fifo address property
2016-11-18 6:29 ` [PATCH v6 0/5] Add intial support to DW MMC host on ZTE SoC Jun Nie
` (2 preceding siblings ...)
2016-11-18 6:29 ` [PATCH v6 3/5] Documentation: synopsys-dw-mshc: add binding for fifo quirks Jun Nie
@ 2016-11-18 6:29 ` Jun Nie
2016-11-18 6:29 ` [PATCH v6 5/5] mmc: dw: Add fifo watermark alignment property Jun Nie
2016-11-18 6:52 ` [PATCH v6 0/5] Add intial support to DW MMC host on ZTE SoC Jaehoon Chung
5 siblings, 0 replies; 16+ messages in thread
From: Jun Nie @ 2016-11-18 6:29 UTC (permalink / raw)
To: shawn.guo, xie.baoyou
Cc: ulf.hansson, jh80.chung, jason.liu, chen.chaokai, lai.binz,
linux-mmc, Jun Nie
The FIFO address may break default address assumption of 0x100
(version < 0x240A) and 0x200(version >= 0x240A) in current driver.
The new property is introduced to override fifo address via DT
node information.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
---
drivers/mmc/host/dw_mmc.c | 6 +++++-
include/linux/mmc/dw_mmc.h | 2 ++
2 files changed, 7 insertions(+), 1 deletion(-)
diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
index 1c9ee36..696b5e6 100644
--- a/drivers/mmc/host/dw_mmc.c
+++ b/drivers/mmc/host/dw_mmc.c
@@ -2955,6 +2955,8 @@ static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
of_property_read_u32(np, "card-detect-delay", &pdata->detect_delay_ms);
+ of_property_read_u32(np, "data-addr", &host->data_addr_override);
+
if (!of_property_read_u32(np, "clock-frequency", &clock_frequency))
pdata->bus_hz = clock_frequency;
@@ -3158,7 +3160,9 @@ int dw_mci_probe(struct dw_mci *host)
host->verid = SDMMC_GET_VERID(mci_readl(host, VERID));
dev_info(host->dev, "Version ID is %04x\n", host->verid);
- if (host->verid < DW_MMC_240A)
+ if (host->data_addr_override)
+ host->fifo_reg = host->regs + host->data_addr_override;
+ else if (host->verid < DW_MMC_240A)
host->fifo_reg = host->regs + DATA_OFFSET;
else
host->fifo_reg = host->regs + DATA_240A_OFFSET;
diff --git a/include/linux/mmc/dw_mmc.h b/include/linux/mmc/dw_mmc.h
index f5af2bd..17cb95a 100644
--- a/include/linux/mmc/dw_mmc.h
+++ b/include/linux/mmc/dw_mmc.h
@@ -107,6 +107,7 @@ struct dw_mci_dma_slave {
* @ciu_clk: Pointer to card interface unit clock instance.
* @slot: Slots sharing this MMC controller.
* @fifo_depth: depth of FIFO.
+ * @data_addr_override: override fifo reg offset with this value.
* @data_shift: log2 of FIFO item size.
* @part_buf_start: Start index in part_buf.
* @part_buf_count: Bytes of partial data in part_buf.
@@ -154,6 +155,7 @@ struct dw_mci {
spinlock_t irq_lock;
void __iomem *regs;
void __iomem *fifo_reg;
+ u32 data_addr_override;
struct scatterlist *sg;
struct sg_mapping_iter sg_miter;
--
1.9.1
^ permalink raw reply related [flat|nested] 16+ messages in thread* [PATCH v6 5/5] mmc: dw: Add fifo watermark alignment property
2016-11-18 6:29 ` [PATCH v6 0/5] Add intial support to DW MMC host on ZTE SoC Jun Nie
` (3 preceding siblings ...)
2016-11-18 6:29 ` [PATCH v6 4/5] mmc: dw: Add fifo address property Jun Nie
@ 2016-11-18 6:29 ` Jun Nie
2016-11-18 6:52 ` [PATCH v6 0/5] Add intial support to DW MMC host on ZTE SoC Jaehoon Chung
5 siblings, 0 replies; 16+ messages in thread
From: Jun Nie @ 2016-11-18 6:29 UTC (permalink / raw)
To: shawn.guo, xie.baoyou
Cc: ulf.hansson, jh80.chung, jason.liu, chen.chaokai, lai.binz,
linux-mmc, Jun Nie
Data done irq is expected if data length is less than
watermark in PIO mode. But fifo watermark is requested
to be aligned with data length in some SoC so that TX/RX
irq can be generated with data done irq. Add the
watermark alignment to mark this requirement and force
fifo watermark setting accordingly.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
---
drivers/mmc/host/dw_mmc.c | 11 +++++++++--
include/linux/mmc/dw_mmc.h | 3 +++
2 files changed, 12 insertions(+), 2 deletions(-)
diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
index 696b5e6..6d85ca6 100644
--- a/drivers/mmc/host/dw_mmc.c
+++ b/drivers/mmc/host/dw_mmc.c
@@ -1111,11 +1111,15 @@ static void dw_mci_submit_data(struct dw_mci *host, struct mmc_data *data)
mci_writel(host, CTRL, temp);
/*
- * Use the initial fifoth_val for PIO mode.
+ * Use the initial fifoth_val for PIO mode. If wm_algined
+ * is set, we set watermark same as data size.
* If next issued data may be transfered by DMA mode,
* prev_blksz should be invalidated.
*/
- mci_writel(host, FIFOTH, host->fifoth_val);
+ if (host->wm_aligned)
+ dw_mci_adjust_fifoth(host, data);
+ else
+ mci_writel(host, FIFOTH, host->fifoth_val);
host->prev_blksz = 0;
} else {
/*
@@ -2957,6 +2961,9 @@ static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
of_property_read_u32(np, "data-addr", &host->data_addr_override);
+ if (of_get_property(np, "fifo-watermark-aligned", NULL))
+ host->wm_aligned = true;
+
if (!of_property_read_u32(np, "clock-frequency", &clock_frequency))
pdata->bus_hz = clock_frequency;
diff --git a/include/linux/mmc/dw_mmc.h b/include/linux/mmc/dw_mmc.h
index 17cb95a..ee4bb30 100644
--- a/include/linux/mmc/dw_mmc.h
+++ b/include/linux/mmc/dw_mmc.h
@@ -108,6 +108,8 @@ struct dw_mci_dma_slave {
* @slot: Slots sharing this MMC controller.
* @fifo_depth: depth of FIFO.
* @data_addr_override: override fifo reg offset with this value.
+ * @wm_aligned: force fifo watermark equal with data length in PIO mode.
+ * Set as true if alignment is needed.
* @data_shift: log2 of FIFO item size.
* @part_buf_start: Start index in part_buf.
* @part_buf_count: Bytes of partial data in part_buf.
@@ -156,6 +158,7 @@ struct dw_mci {
void __iomem *regs;
void __iomem *fifo_reg;
u32 data_addr_override;
+ bool wm_aligned;
struct scatterlist *sg;
struct sg_mapping_iter sg_miter;
--
1.9.1
^ permalink raw reply related [flat|nested] 16+ messages in thread* Re: [PATCH v6 0/5] Add intial support to DW MMC host on ZTE SoC
2016-11-18 6:29 ` [PATCH v6 0/5] Add intial support to DW MMC host on ZTE SoC Jun Nie
` (4 preceding siblings ...)
2016-11-18 6:29 ` [PATCH v6 5/5] mmc: dw: Add fifo watermark alignment property Jun Nie
@ 2016-11-18 6:52 ` Jaehoon Chung
2016-11-18 14:31 ` Ulf Hansson
5 siblings, 1 reply; 16+ messages in thread
From: Jaehoon Chung @ 2016-11-18 6:52 UTC (permalink / raw)
To: Jun Nie, shawn.guo, xie.baoyou
Cc: ulf.hansson, jason.liu, chen.chaokai, lai.binz, linux-mmc
Hi Jun,
On 11/18/2016 03:29 PM, Jun Nie wrote:
> Add intial support to DW MMC host on ZTE SoC. It include platform
> specific wrapper driver and workarounds for fifo quirk.
>
> Patches are prepared based on latest dw mmc runtime change:
> https://github.com/jh80chung/dw-mmc.git for-ulf
Applied on my dwmmc repository.
I have applied your patches, after modifying some conflict and subject prefix as "dw_mmc*".
And added Shawn's reviewed-by tags. Thanks!
Best Regards,
Jaehoon Chung
>
> Changes vs version 5:
> - Add clock delay lock status check to save CPU cycle in timing tuning CMD.
>
> Changes vs version 4:
> - Fix missing empty dts compatible element in the end of compatible array.
>
> Changes vs version 3:
> - Fix brace error in document.
>
> Changes vs version 2:
> - Change dt property fifo-addr to data-addr and fifo-watermark-quirk to
> fifo-watermark-aligned.
> - Polish ZX MMC driver on minor coding style issues.
>
> Changes vs version 1:
> - Change fifo-addr-override to fifo-addr and remove its workaround tag in comments.
> - Remove ZX DW MMC driver reset cap in driver, which can be added in dt nodes.
>
> Jun Nie (5):
> mmc: dt-bindings: add ZTE ZX296718 MMC bindings
> mmc: zx: Initial support for ZX mmc controller
> Documentation: synopsys-dw-mshc: add binding for fifo quirks
> mmc: dw: Add fifo address property
> mmc: dw: Add fifo watermark alignment property
>
> .../devicetree/bindings/mmc/synopsys-dw-mshc.txt | 13 ++
> .../devicetree/bindings/mmc/zx-dw-mshc.txt | 34 +++
> drivers/mmc/host/Kconfig | 9 +
> drivers/mmc/host/Makefile | 1 +
> drivers/mmc/host/dw_mmc-zx.c | 242 +++++++++++++++++++++
> drivers/mmc/host/dw_mmc-zx.h | 31 +++
> drivers/mmc/host/dw_mmc.c | 17 +-
> include/linux/mmc/dw_mmc.h | 5 +
> 8 files changed, 349 insertions(+), 3 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
> create mode 100644 drivers/mmc/host/dw_mmc-zx.c
> create mode 100644 drivers/mmc/host/dw_mmc-zx.h
>
^ permalink raw reply [flat|nested] 16+ messages in thread* Re: [PATCH v6 0/5] Add intial support to DW MMC host on ZTE SoC
2016-11-18 6:52 ` [PATCH v6 0/5] Add intial support to DW MMC host on ZTE SoC Jaehoon Chung
@ 2016-11-18 14:31 ` Ulf Hansson
2016-11-21 1:22 ` Jaehoon Chung
0 siblings, 1 reply; 16+ messages in thread
From: Ulf Hansson @ 2016-11-18 14:31 UTC (permalink / raw)
To: Jaehoon Chung
Cc: Jun Nie, Shawn Guo, xie.baoyou, jason.liu, chen.chaokai,
lai.binz, linux-mmc
On 18 November 2016 at 07:52, Jaehoon Chung <jh80.chung@samsung.com> wrote:
> Hi Jun,
>
> On 11/18/2016 03:29 PM, Jun Nie wrote:
>> Add intial support to DW MMC host on ZTE SoC. It include platform
>> specific wrapper driver and workarounds for fifo quirk.
>>
>> Patches are prepared based on latest dw mmc runtime change:
>> https://github.com/jh80chung/dw-mmc.git for-ulf
>
> Applied on my dwmmc repository.
> I have applied your patches, after modifying some conflict and subject prefix as "dw_mmc*".
> And added Shawn's reviewed-by tags. Thanks!
[...]
>> Jun Nie (5):
>> mmc: dt-bindings: add ZTE ZX296718 MMC bindings
Don't forget to make sure DT bindings get acked. I don't think I have
seen that happening for this change, unless I missed it of course.
[...]
Kind regards
Uffe
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v6 0/5] Add intial support to DW MMC host on ZTE SoC
2016-11-18 14:31 ` Ulf Hansson
@ 2016-11-21 1:22 ` Jaehoon Chung
0 siblings, 0 replies; 16+ messages in thread
From: Jaehoon Chung @ 2016-11-21 1:22 UTC (permalink / raw)
To: Ulf Hansson
Cc: Jun Nie, Shawn Guo, xie.baoyou, jason.liu, chen.chaokai,
lai.binz, linux-mmc
Hi Ulf,
On 11/18/2016 11:31 PM, Ulf Hansson wrote:
> On 18 November 2016 at 07:52, Jaehoon Chung <jh80.chung@samsung.com> wrote:
>> Hi Jun,
>>
>> On 11/18/2016 03:29 PM, Jun Nie wrote:
>>> Add intial support to DW MMC host on ZTE SoC. It include platform
>>> specific wrapper driver and workarounds for fifo quirk.
>>>
>>> Patches are prepared based on latest dw mmc runtime change:
>>> https://github.com/jh80chung/dw-mmc.git for-ulf
>>
>> Applied on my dwmmc repository.
>> I have applied your patches, after modifying some conflict and subject prefix as "dw_mmc*".
>> And added Shawn's reviewed-by tags. Thanks!
>
> [...]
>
>>> Jun Nie (5):
>>> mmc: dt-bindings: add ZTE ZX296718 MMC bindings
>
> Don't forget to make sure DT bindings get acked. I don't think I have
> seen that happening for this change, unless I missed it of course.
Thanks for noticing this. I will wait for DT guy's acked.
Best Regards,
Jaehoon Chung
>
> [...]
>
> Kind regards
> Uffe
> --
> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
>
>
^ permalink raw reply [flat|nested] 16+ messages in thread