* [PATCH v10 0/3] Add support for the S6E3HA2 panel on TM2 board [not found] <CGME20170220071000epcas1p38e002e5064bdf4c3b1b4886207dcaaf4@epcas1p3.samsung.com> @ 2017-02-20 7:09 ` Hoegeun Kwon 2017-02-22 1:09 ` Hoegeun Kwon 1 sibling, 0 replies; 31+ messages in thread From: Hoegeun Kwon @ 2017-02-20 7:09 UTC (permalink / raw) To: thierry.reding, airlied, kgene, krzk, robh+dt Cc: dri-devel, linux-kernel, devicetree, linux-samsung-soc, inki.dae, a.hajda, cw00.choi, jh80.chung, andi.shyti, Hoegeun Kwon Dear Thierry, I understand that your opinion is: It is better to handle the error every time it is input to the register, rather than error handling at once in the struct using error. This not only makes the code easier to maintain, but also reduces unnecessary computation. So I modified the panel driver to code-by-code error handling. If this is not your opinion, could you tell me what your opinion? Best Regards, Hoegeun Changes for V10: - Fixed code-by-code error handling. Changes for V9: - Fixed the te-gpio to optional in bindings Changes for V8: - Applied below two patches: (drm/exynos) : drm/exynos: mic: Add mode_set callback function : drm/exynos: mic: Fix parse_dt function - The dt-binding patch and driver patch were divided. - Rebase these patches on samsung SoC tree[1] and tm2 touckey patch[2]. Change for V7: - Fixed the mode_set callback function of mic device driver. because the mic register is initialized when entering suspend mode, so should set the reg value whenever pre_enable is called. Changes for V6: - Fixed the parse_dt function of dsi device driver. - Removed OF graph of panel in DT and DT binding document. - Fixed the s6e3ha2 panel device driver. - Fixed from number size to ARRAY_SIZE(). - Fixed error handling in mipi_dsi_dcs_* functions. - Fixed the clock of display_mode. - Removed unnecessary casting and error log. Change for V5: - The V5 has only one fix in V4 below. - Removed the enable check of the mic driver in mode_set callback, because mode_set should be performed every time. Changes for V4: - Removed display-timings in devicetree, the display-timings has been fixed to be provided by the device driver. - Added the mode_set callback function into exynos_drm_mic, because the exynos_drm_mic driver can not parse a videomode struct by removing the display-timings from the devicetree. Changes for V3: - In the DT binding document, made it clearly that the panel is a child node of dsi. - Fix reset-gpio active from high to low. - Is the OF graph saying related to patch2? Althogh the panel is a child of dsi, I think OF graph necessary. because if a remote-endpoint is not specified, the dsi also panel is not probed. - The display-timings has been fixed to be provided by the device driver. however, I think display-timings is necessary in dts. because if dts does not have display-timings, dsi will not load. Changes for V2: - Fixed the samsung,s6e3ha2.txt DT document. - Added active high or low after the description of the GPIOs. - Removed the reg and added a description of the virtual channel number of a DSI peripheral. Depends on: [1] https://git.kernel.org/cgit/linux/kernel/git/krzk/linux.git/ (for-next branch) [2] https://patchwork.kernel.org/patch/9504131/ - ("arm64: dts: exynos: Add tm2 touchkey node") Hoegeun Kwon (2): dt-bindings: Add support for samsung s6e3ha2 panel binding drm/panel: Add support for S6E3HA2 panel driver on TM2 board Hyungwon Hwang (1): arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board .../bindings/display/panel/samsung,s6e3ha2.txt | 28 + arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 12 + drivers/gpu/drm/panel/Kconfig | 6 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c | 739 +++++++++++++++++++++ 5 files changed, 786 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c -- 1.9.1 ^ permalink raw reply [flat|nested] 31+ messages in thread
* [PATCH v10 0/3] Add support for the S6E3HA2 panel on TM2 board @ 2017-02-20 7:09 ` Hoegeun Kwon 0 siblings, 0 replies; 31+ messages in thread From: Hoegeun Kwon @ 2017-02-20 7:09 UTC (permalink / raw) To: thierry.reding-Re5JQEeQqe8AvxtiuMwx3w, airlied-cv59FeDIM0c, kgene-DgEjT+Ai2ygdnm+yROfE0A, krzk-DgEjT+Ai2ygdnm+yROfE0A, robh+dt-DgEjT+Ai2ygdnm+yROfE0A Cc: dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW, linux-kernel-u79uwXL29TY76Z2rM5mHXA, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-samsung-soc-u79uwXL29TY76Z2rM5mHXA, inki.dae-Sze3O3UU22JBDgjK7y7TUQ, a.hajda-Sze3O3UU22JBDgjK7y7TUQ, cw00.choi-Sze3O3UU22JBDgjK7y7TUQ, jh80.chung-Sze3O3UU22JBDgjK7y7TUQ, andi.shyti-Sze3O3UU22JBDgjK7y7TUQ, Hoegeun Kwon Dear Thierry, I understand that your opinion is: It is better to handle the error every time it is input to the register, rather than error handling at once in the struct using error. This not only makes the code easier to maintain, but also reduces unnecessary computation. So I modified the panel driver to code-by-code error handling. If this is not your opinion, could you tell me what your opinion? Best Regards, Hoegeun Changes for V10: - Fixed code-by-code error handling. Changes for V9: - Fixed the te-gpio to optional in bindings Changes for V8: - Applied below two patches: (drm/exynos) : drm/exynos: mic: Add mode_set callback function : drm/exynos: mic: Fix parse_dt function - The dt-binding patch and driver patch were divided. - Rebase these patches on samsung SoC tree[1] and tm2 touckey patch[2]. Change for V7: - Fixed the mode_set callback function of mic device driver. because the mic register is initialized when entering suspend mode, so should set the reg value whenever pre_enable is called. Changes for V6: - Fixed the parse_dt function of dsi device driver. - Removed OF graph of panel in DT and DT binding document. - Fixed the s6e3ha2 panel device driver. - Fixed from number size to ARRAY_SIZE(). - Fixed error handling in mipi_dsi_dcs_* functions. - Fixed the clock of display_mode. - Removed unnecessary casting and error log. Change for V5: - The V5 has only one fix in V4 below. - Removed the enable check of the mic driver in mode_set callback, because mode_set should be performed every time. Changes for V4: - Removed display-timings in devicetree, the display-timings has been fixed to be provided by the device driver. - Added the mode_set callback function into exynos_drm_mic, because the exynos_drm_mic driver can not parse a videomode struct by removing the display-timings from the devicetree. Changes for V3: - In the DT binding document, made it clearly that the panel is a child node of dsi. - Fix reset-gpio active from high to low. - Is the OF graph saying related to patch2? Althogh the panel is a child of dsi, I think OF graph necessary. because if a remote-endpoint is not specified, the dsi also panel is not probed. - The display-timings has been fixed to be provided by the device driver. however, I think display-timings is necessary in dts. because if dts does not have display-timings, dsi will not load. Changes for V2: - Fixed the samsung,s6e3ha2.txt DT document. - Added active high or low after the description of the GPIOs. - Removed the reg and added a description of the virtual channel number of a DSI peripheral. Depends on: [1] https://git.kernel.org/cgit/linux/kernel/git/krzk/linux.git/ (for-next branch) [2] https://patchwork.kernel.org/patch/9504131/ - ("arm64: dts: exynos: Add tm2 touchkey node") Hoegeun Kwon (2): dt-bindings: Add support for samsung s6e3ha2 panel binding drm/panel: Add support for S6E3HA2 panel driver on TM2 board Hyungwon Hwang (1): arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board .../bindings/display/panel/samsung,s6e3ha2.txt | 28 + arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 12 + drivers/gpu/drm/panel/Kconfig | 6 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c | 739 +++++++++++++++++++++ 5 files changed, 786 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 31+ messages in thread
[parent not found: <CGME20170220071000epcas1p3fbc906fa085931b73b895b6724432cd3@epcas1p3.samsung.com>]
* [PATCH v10 1/3] dt-bindings: Add support for samsung s6e3ha2 panel binding [not found] ` <CGME20170220071000epcas1p3fbc906fa085931b73b895b6724432cd3@epcas1p3.samsung.com> @ 2017-02-20 7:09 ` Hoegeun Kwon 2017-02-22 1:09 ` Hoegeun Kwon 1 sibling, 0 replies; 31+ messages in thread From: Hoegeun Kwon @ 2017-02-20 7:09 UTC (permalink / raw) To: thierry.reding, airlied, kgene, krzk, robh+dt Cc: dri-devel, linux-kernel, devicetree, linux-samsung-soc, inki.dae, a.hajda, cw00.choi, jh80.chung, andi.shyti, Hoegeun Kwon, Donghwa Lee, Hyungwon Hwang The Samsung s6e3ha2 is a 5.7" 1440x2560 AMOLED panel connected using MIPI-DSI interfaces. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Acked-by: Rob Herring <robh@kernel.org> --- .../bindings/display/panel/samsung,s6e3ha2.txt | 28 ++++++++++++++++++++++ 1 file changed, 28 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt new file mode 100644 index 0000000..18854f4 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt @@ -0,0 +1,28 @@ +Samsung S6E3HA2 5.7" 1440x2560 AMOLED panel + +Required properties: + - compatible: "samsung,s6e3ha2" + - reg: the virtual channel number of a DSI peripheral + - vdd3-supply: I/O voltage supply + - vci-supply: voltage supply for analog circuits + - reset-gpios: a GPIO spec for the reset pin (active low) + - enable-gpios: a GPIO spec for the panel enable pin (active high) + +Optional properties: + - te-gpios: a GPIO spec for the tearing effect synchronization signal + gpio pin (active high) + +Example: +&dsi { + ... + + panel@0 { + compatible = "samsung,s6e3ha2"; + reg = <0>; + vdd3-supply = <&ldo27_reg>; + vci-supply = <&ldo28_reg>; + reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>; + enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>; + te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>; + }; +}; -- 1.9.1 ^ permalink raw reply related [flat|nested] 31+ messages in thread
* [PATCH v10 1/3] dt-bindings: Add support for samsung s6e3ha2 panel binding @ 2017-02-20 7:09 ` Hoegeun Kwon 0 siblings, 0 replies; 31+ messages in thread From: Hoegeun Kwon @ 2017-02-20 7:09 UTC (permalink / raw) To: thierry.reding, airlied, kgene, krzk, robh+dt Cc: devicetree, linux-samsung-soc, cw00.choi, Donghwa Lee, linux-kernel, dri-devel, jh80.chung, andi.shyti, Hyungwon Hwang, Hoegeun Kwon The Samsung s6e3ha2 is a 5.7" 1440x2560 AMOLED panel connected using MIPI-DSI interfaces. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Acked-by: Rob Herring <robh@kernel.org> --- .../bindings/display/panel/samsung,s6e3ha2.txt | 28 ++++++++++++++++++++++ 1 file changed, 28 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt new file mode 100644 index 0000000..18854f4 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt @@ -0,0 +1,28 @@ +Samsung S6E3HA2 5.7" 1440x2560 AMOLED panel + +Required properties: + - compatible: "samsung,s6e3ha2" + - reg: the virtual channel number of a DSI peripheral + - vdd3-supply: I/O voltage supply + - vci-supply: voltage supply for analog circuits + - reset-gpios: a GPIO spec for the reset pin (active low) + - enable-gpios: a GPIO spec for the panel enable pin (active high) + +Optional properties: + - te-gpios: a GPIO spec for the tearing effect synchronization signal + gpio pin (active high) + +Example: +&dsi { + ... + + panel@0 { + compatible = "samsung,s6e3ha2"; + reg = <0>; + vdd3-supply = <&ldo27_reg>; + vci-supply = <&ldo28_reg>; + reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>; + enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>; + te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>; + }; +}; -- 1.9.1 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply related [flat|nested] 31+ messages in thread
* [PATCH v10 1/3] dt-bindings: Add support for samsung s6e3ha2 panel binding [not found] ` <CGME20170220071000epcas1p3fbc906fa085931b73b895b6724432cd3@epcas1p3.samsung.com> @ 2017-02-22 1:09 ` Hoegeun Kwon 2017-02-22 1:09 ` Hoegeun Kwon 1 sibling, 0 replies; 31+ messages in thread From: Hoegeun Kwon @ 2017-02-22 1:09 UTC (permalink / raw) To: thierry.reding, airlied, robh+dt, mark.rutland, catalin.marinas, will.deacon, kgene, krzk Cc: dri-devel, devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel, javier, inki.dae, a.hajda, cw00.choi, jh80.chung, andi.shyti, Hoegeun Kwon The Samsung s6e3ha2 is a 5.7" 1440x2560 AMOLED panel connected using MIPI-DSI interfaces. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Acked-by: Rob Herring <robh@kernel.org> --- .../bindings/display/panel/samsung,s6e3ha2.txt | 28 ++++++++++++++++++++++ 1 file changed, 28 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt new file mode 100644 index 0000000..18854f4 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt @@ -0,0 +1,28 @@ +Samsung S6E3HA2 5.7" 1440x2560 AMOLED panel + +Required properties: + - compatible: "samsung,s6e3ha2" + - reg: the virtual channel number of a DSI peripheral + - vdd3-supply: I/O voltage supply + - vci-supply: voltage supply for analog circuits + - reset-gpios: a GPIO spec for the reset pin (active low) + - enable-gpios: a GPIO spec for the panel enable pin (active high) + +Optional properties: + - te-gpios: a GPIO spec for the tearing effect synchronization signal + gpio pin (active high) + +Example: +&dsi { + ... + + panel@0 { + compatible = "samsung,s6e3ha2"; + reg = <0>; + vdd3-supply = <&ldo27_reg>; + vci-supply = <&ldo28_reg>; + reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>; + enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>; + te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>; + }; +}; -- 1.9.1 ^ permalink raw reply related [flat|nested] 31+ messages in thread
* [PATCH v10 1/3] dt-bindings: Add support for samsung s6e3ha2 panel binding @ 2017-02-22 1:09 ` Hoegeun Kwon 0 siblings, 0 replies; 31+ messages in thread From: Hoegeun Kwon @ 2017-02-22 1:09 UTC (permalink / raw) To: linux-arm-kernel The Samsung s6e3ha2 is a 5.7" 1440x2560 AMOLED panel connected using MIPI-DSI interfaces. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Acked-by: Rob Herring <robh@kernel.org> --- .../bindings/display/panel/samsung,s6e3ha2.txt | 28 ++++++++++++++++++++++ 1 file changed, 28 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt new file mode 100644 index 0000000..18854f4 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt @@ -0,0 +1,28 @@ +Samsung S6E3HA2 5.7" 1440x2560 AMOLED panel + +Required properties: + - compatible: "samsung,s6e3ha2" + - reg: the virtual channel number of a DSI peripheral + - vdd3-supply: I/O voltage supply + - vci-supply: voltage supply for analog circuits + - reset-gpios: a GPIO spec for the reset pin (active low) + - enable-gpios: a GPIO spec for the panel enable pin (active high) + +Optional properties: + - te-gpios: a GPIO spec for the tearing effect synchronization signal + gpio pin (active high) + +Example: +&dsi { + ... + + panel at 0 { + compatible = "samsung,s6e3ha2"; + reg = <0>; + vdd3-supply = <&ldo27_reg>; + vci-supply = <&ldo28_reg>; + reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>; + enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>; + te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>; + }; +}; -- 1.9.1 ^ permalink raw reply related [flat|nested] 31+ messages in thread
* Re: [PATCH v10 1/3] dt-bindings: Add support for samsung s6e3ha2 panel binding 2017-02-22 1:09 ` Hoegeun Kwon (?) @ 2017-03-06 14:35 ` Javier Martinez Canillas -1 siblings, 0 replies; 31+ messages in thread From: Javier Martinez Canillas @ 2017-03-06 14:35 UTC (permalink / raw) To: Hoegeun Kwon, thierry.reding, airlied, robh+dt, mark.rutland, catalin.marinas, will.deacon, kgene, krzk Cc: dri-devel, devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel, inki.dae, a.hajda, cw00.choi, jh80.chung, andi.shyti Hello Hoegeun, On 02/21/2017 10:09 PM, Hoegeun Kwon wrote: > The Samsung s6e3ha2 is a 5.7" 1440x2560 AMOLED panel connected > using MIPI-DSI interfaces. > > Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> > Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> > Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> > Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> > Acked-by: Rob Herring <robh@kernel.org> > --- Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Best regards, -- Javier Martinez Canillas Open Source Group Samsung Research America ^ permalink raw reply [flat|nested] 31+ messages in thread
* [PATCH v10 1/3] dt-bindings: Add support for samsung s6e3ha2 panel binding @ 2017-03-06 14:35 ` Javier Martinez Canillas 0 siblings, 0 replies; 31+ messages in thread From: Javier Martinez Canillas @ 2017-03-06 14:35 UTC (permalink / raw) To: linux-arm-kernel Hello Hoegeun, On 02/21/2017 10:09 PM, Hoegeun Kwon wrote: > The Samsung s6e3ha2 is a 5.7" 1440x2560 AMOLED panel connected > using MIPI-DSI interfaces. > > Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> > Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> > Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> > Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> > Acked-by: Rob Herring <robh@kernel.org> > --- Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Best regards, -- Javier Martinez Canillas Open Source Group Samsung Research America ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: [PATCH v10 1/3] dt-bindings: Add support for samsung s6e3ha2 panel binding @ 2017-03-06 14:35 ` Javier Martinez Canillas 0 siblings, 0 replies; 31+ messages in thread From: Javier Martinez Canillas @ 2017-03-06 14:35 UTC (permalink / raw) To: Hoegeun Kwon, thierry.reding, airlied, robh+dt, mark.rutland, catalin.marinas, will.deacon, kgene, krzk Cc: devicetree, linux-samsung-soc, cw00.choi, linux-kernel, dri-devel, jh80.chung, andi.shyti, linux-arm-kernel Hello Hoegeun, On 02/21/2017 10:09 PM, Hoegeun Kwon wrote: > The Samsung s6e3ha2 is a 5.7" 1440x2560 AMOLED panel connected > using MIPI-DSI interfaces. > > Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> > Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> > Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> > Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> > Acked-by: Rob Herring <robh@kernel.org> > --- Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Best regards, -- Javier Martinez Canillas Open Source Group Samsung Research America _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply [flat|nested] 31+ messages in thread
[parent not found: <CGME20170220071001epcas1p3c2b32665942ba55c3ed4e06d2c66d661@epcas1p3.samsung.com>]
* [PATCH v10 3/3] arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board [not found] ` <CGME20170220071001epcas1p3c2b32665942ba55c3ed4e06d2c66d661@epcas1p3.samsung.com> @ 2017-02-20 7:09 ` Hoegeun Kwon 2017-02-22 1:09 ` Hoegeun Kwon 1 sibling, 0 replies; 31+ messages in thread From: Hoegeun Kwon @ 2017-02-20 7:09 UTC (permalink / raw) To: thierry.reding, airlied, kgene, krzk, robh+dt Cc: dri-devel, linux-kernel, devicetree, linux-samsung-soc, inki.dae, a.hajda, cw00.choi, jh80.chung, andi.shyti, Hyungwon Hwang, Hoegeun Kwon From: Hyungwon Hwang <human.hwang@samsung.com> This patch add the panel device tree node for S6E3HA2 display controller to TM2 dts. Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> Tested-by: Chanwoo Choi <cw00.choi@samsung.com> --- arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts index dea0a6f..db3fed2 100644 --- a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts @@ -52,6 +52,18 @@ assigned-clock-rates = <250000000>, <400000000>; }; +&dsi { + panel@0 { + compatible = "samsung,s6e3ha2"; + reg = <0>; + vdd3-supply = <&ldo27_reg>; + vci-supply = <&ldo28_reg>; + reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>; + enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>; + te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>; + }; +}; + &hsi2c_9 { status = "okay"; -- 1.9.1 ^ permalink raw reply related [flat|nested] 31+ messages in thread
* [PATCH v10 3/3] arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board @ 2017-02-20 7:09 ` Hoegeun Kwon 0 siblings, 0 replies; 31+ messages in thread From: Hoegeun Kwon @ 2017-02-20 7:09 UTC (permalink / raw) To: thierry.reding, airlied, kgene, krzk, robh+dt Cc: devicetree, linux-samsung-soc, cw00.choi, linux-kernel, dri-devel, jh80.chung, andi.shyti, Hyungwon Hwang, Hoegeun Kwon From: Hyungwon Hwang <human.hwang@samsung.com> This patch add the panel device tree node for S6E3HA2 display controller to TM2 dts. Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> Tested-by: Chanwoo Choi <cw00.choi@samsung.com> --- arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts index dea0a6f..db3fed2 100644 --- a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts @@ -52,6 +52,18 @@ assigned-clock-rates = <250000000>, <400000000>; }; +&dsi { + panel@0 { + compatible = "samsung,s6e3ha2"; + reg = <0>; + vdd3-supply = <&ldo27_reg>; + vci-supply = <&ldo28_reg>; + reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>; + enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>; + te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>; + }; +}; + &hsi2c_9 { status = "okay"; -- 1.9.1 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply related [flat|nested] 31+ messages in thread
* Re: [PATCH v10 3/3] arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board 2017-02-20 7:09 ` Hoegeun Kwon (?) @ 2017-02-20 13:20 ` Krzysztof Kozlowski -1 siblings, 0 replies; 31+ messages in thread From: Krzysztof Kozlowski @ 2017-02-20 13:20 UTC (permalink / raw) To: Hoegeun Kwon Cc: thierry.reding, airlied, kgene, robh+dt, dri-devel, linux-kernel, devicetree, linux-samsung-soc, Inki Dae, a.hajda, Chanwoo Choi, Jaehoon Chung, Andi Shyti, Hyungwon Hwang On Mon, Feb 20, 2017 at 9:09 AM, Hoegeun Kwon <hoegeun.kwon@samsung.com> wrote: > From: Hyungwon Hwang <human.hwang@samsung.com> > > This patch add the panel device tree node for S6E3HA2 display > controller to TM2 dts. > > Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> > Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> > Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> > Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> > Tested-by: Chanwoo Choi <cw00.choi@samsung.com> > --- > arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 12 ++++++++++++ > 1 file changed, 12 insertions(+) Please use scripts/get_maintainer.pl to get the list of people to CC. Here you missed Javier, so I am worried that you run this driver not on mainline kernel but on some old one... Best regards, Krzysztof ^ permalink raw reply [flat|nested] 31+ messages in thread
* [PATCH v10 3/3] arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board [not found] ` <CGME20170220071001epcas1p3c2b32665942ba55c3ed4e06d2c66d661@epcas1p3.samsung.com> 2017-02-20 7:09 ` Hoegeun Kwon @ 2017-02-22 1:09 ` Hoegeun Kwon 1 sibling, 0 replies; 31+ messages in thread From: Hoegeun Kwon @ 2017-02-22 1:09 UTC (permalink / raw) To: thierry.reding, airlied, robh+dt, mark.rutland, catalin.marinas, will.deacon, kgene, krzk Cc: dri-devel, devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel, javier, inki.dae, a.hajda, cw00.choi, jh80.chung, andi.shyti, Hoegeun Kwon From: Hyungwon Hwang <human.hwang@samsung.com> This patch add the panel device tree node for S6E3HA2 display controller to TM2 dts. Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> Tested-by: Chanwoo Choi <cw00.choi@samsung.com> --- arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts index dea0a6f..db3fed2 100644 --- a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts @@ -52,6 +52,18 @@ assigned-clock-rates = <250000000>, <400000000>; }; +&dsi { + panel@0 { + compatible = "samsung,s6e3ha2"; + reg = <0>; + vdd3-supply = <&ldo27_reg>; + vci-supply = <&ldo28_reg>; + reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>; + enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>; + te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>; + }; +}; + &hsi2c_9 { status = "okay"; -- 1.9.1 ^ permalink raw reply related [flat|nested] 31+ messages in thread
* [PATCH v10 3/3] arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board @ 2017-02-22 1:09 ` Hoegeun Kwon 0 siblings, 0 replies; 31+ messages in thread From: Hoegeun Kwon @ 2017-02-22 1:09 UTC (permalink / raw) To: linux-arm-kernel From: Hyungwon Hwang <human.hwang@samsung.com> This patch add the panel device tree node for S6E3HA2 display controller to TM2 dts. Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> Tested-by: Chanwoo Choi <cw00.choi@samsung.com> --- arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts index dea0a6f..db3fed2 100644 --- a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts @@ -52,6 +52,18 @@ assigned-clock-rates = <250000000>, <400000000>; }; +&dsi { + panel at 0 { + compatible = "samsung,s6e3ha2"; + reg = <0>; + vdd3-supply = <&ldo27_reg>; + vci-supply = <&ldo28_reg>; + reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>; + enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>; + te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>; + }; +}; + &hsi2c_9 { status = "okay"; -- 1.9.1 ^ permalink raw reply related [flat|nested] 31+ messages in thread
* [PATCH v10 3/3] arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board @ 2017-02-22 1:09 ` Hoegeun Kwon 0 siblings, 0 replies; 31+ messages in thread From: Hoegeun Kwon @ 2017-02-22 1:09 UTC (permalink / raw) To: thierry.reding, airlied, robh+dt, mark.rutland, catalin.marinas, will.deacon, kgene, krzk Cc: devicetree, linux-samsung-soc, cw00.choi, linux-kernel, dri-devel, javier, jh80.chung, andi.shyti, Hoegeun Kwon, linux-arm-kernel From: Hyungwon Hwang <human.hwang@samsung.com> This patch add the panel device tree node for S6E3HA2 display controller to TM2 dts. Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> Tested-by: Chanwoo Choi <cw00.choi@samsung.com> --- arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts index dea0a6f..db3fed2 100644 --- a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts @@ -52,6 +52,18 @@ assigned-clock-rates = <250000000>, <400000000>; }; +&dsi { + panel@0 { + compatible = "samsung,s6e3ha2"; + reg = <0>; + vdd3-supply = <&ldo27_reg>; + vci-supply = <&ldo28_reg>; + reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>; + enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>; + te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>; + }; +}; + &hsi2c_9 { status = "okay"; -- 1.9.1 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply related [flat|nested] 31+ messages in thread
* Re: [PATCH v10 3/3] arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board 2017-02-22 1:09 ` Hoegeun Kwon (?) @ 2017-03-06 14:42 ` Javier Martinez Canillas -1 siblings, 0 replies; 31+ messages in thread From: Javier Martinez Canillas @ 2017-03-06 14:42 UTC (permalink / raw) To: Hoegeun Kwon, thierry.reding, airlied, robh+dt, mark.rutland, catalin.marinas, will.deacon, kgene, krzk Cc: dri-devel, devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel, inki.dae, a.hajda, cw00.choi, jh80.chung, andi.shyti Hello Hoegeun, On 02/21/2017 10:09 PM, Hoegeun Kwon wrote: > From: Hyungwon Hwang <human.hwang@samsung.com> > > This patch add the panel device tree node for S6E3HA2 display > controller to TM2 dts. > > Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> > Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> > Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> > Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> > Tested-by: Chanwoo Choi <cw00.choi@samsung.com> > --- > arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 12 ++++++++++++ > 1 file changed, 12 insertions(+) > > diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts > index dea0a6f..db3fed2 100644 > --- a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts > +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts > @@ -52,6 +52,18 @@ > assigned-clock-rates = <250000000>, <400000000>; > }; I would add a line here. > +&dsi { > + panel@0 { > + compatible = "samsung,s6e3ha2"; > + reg = <0>; > + vdd3-supply = <&ldo27_reg>; > + vci-supply = <&ldo28_reg>; > + reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>; > + enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>; > + te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>; > + }; > +}; > + Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Best regards, -- Javier Martinez Canillas Open Source Group Samsung Research America ^ permalink raw reply [flat|nested] 31+ messages in thread
* [PATCH v10 3/3] arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board @ 2017-03-06 14:42 ` Javier Martinez Canillas 0 siblings, 0 replies; 31+ messages in thread From: Javier Martinez Canillas @ 2017-03-06 14:42 UTC (permalink / raw) To: linux-arm-kernel Hello Hoegeun, On 02/21/2017 10:09 PM, Hoegeun Kwon wrote: > From: Hyungwon Hwang <human.hwang@samsung.com> > > This patch add the panel device tree node for S6E3HA2 display > controller to TM2 dts. > > Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> > Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> > Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> > Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> > Tested-by: Chanwoo Choi <cw00.choi@samsung.com> > --- > arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 12 ++++++++++++ > 1 file changed, 12 insertions(+) > > diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts > index dea0a6f..db3fed2 100644 > --- a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts > +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts > @@ -52,6 +52,18 @@ > assigned-clock-rates = <250000000>, <400000000>; > }; I would add a line here. > +&dsi { > + panel at 0 { > + compatible = "samsung,s6e3ha2"; > + reg = <0>; > + vdd3-supply = <&ldo27_reg>; > + vci-supply = <&ldo28_reg>; > + reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>; > + enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>; > + te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>; > + }; > +}; > + Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Best regards, -- Javier Martinez Canillas Open Source Group Samsung Research America ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: [PATCH v10 3/3] arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board @ 2017-03-06 14:42 ` Javier Martinez Canillas 0 siblings, 0 replies; 31+ messages in thread From: Javier Martinez Canillas @ 2017-03-06 14:42 UTC (permalink / raw) To: Hoegeun Kwon, thierry.reding, airlied, robh+dt, mark.rutland, catalin.marinas, will.deacon, kgene, krzk Cc: devicetree, linux-samsung-soc, cw00.choi, linux-kernel, dri-devel, jh80.chung, andi.shyti, linux-arm-kernel Hello Hoegeun, On 02/21/2017 10:09 PM, Hoegeun Kwon wrote: > From: Hyungwon Hwang <human.hwang@samsung.com> > > This patch add the panel device tree node for S6E3HA2 display > controller to TM2 dts. > > Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> > Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> > Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> > Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> > Tested-by: Chanwoo Choi <cw00.choi@samsung.com> > --- > arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 12 ++++++++++++ > 1 file changed, 12 insertions(+) > > diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts > index dea0a6f..db3fed2 100644 > --- a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts > +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts > @@ -52,6 +52,18 @@ > assigned-clock-rates = <250000000>, <400000000>; > }; I would add a line here. > +&dsi { > + panel@0 { > + compatible = "samsung,s6e3ha2"; > + reg = <0>; > + vdd3-supply = <&ldo27_reg>; > + vci-supply = <&ldo28_reg>; > + reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>; > + enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>; > + te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>; > + }; > +}; > + Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Best regards, -- Javier Martinez Canillas Open Source Group Samsung Research America _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: [PATCH v10 3/3] arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board 2017-02-22 1:09 ` Hoegeun Kwon (?) @ 2017-03-07 20:17 ` Krzysztof Kozlowski -1 siblings, 0 replies; 31+ messages in thread From: Krzysztof Kozlowski @ 2017-03-07 20:17 UTC (permalink / raw) To: Hoegeun Kwon Cc: thierry.reding, airlied, robh+dt, mark.rutland, catalin.marinas, will.deacon, kgene, dri-devel, devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel, javier, inki.dae, a.hajda, cw00.choi, jh80.chung, andi.shyti On Wed, Feb 22, 2017 at 10:09:54AM +0900, Hoegeun Kwon wrote: > From: Hyungwon Hwang <human.hwang@samsung.com> > > This patch add the panel device tree node for S6E3HA2 display > controller to TM2 dts. > > Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> > Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> > Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> > Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> > Tested-by: Chanwoo Choi <cw00.choi@samsung.com> > --- > arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 12 ++++++++++++ > 1 file changed, 12 insertions(+) I tried to apply but: fatal: corrupt patch at line 37 Patch failed at 0001 arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board Please fix, rebase, add blank link as suggested by Javier and send a v11. Best regards, Krzysztof ^ permalink raw reply [flat|nested] 31+ messages in thread
* [PATCH v10 3/3] arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board @ 2017-03-07 20:17 ` Krzysztof Kozlowski 0 siblings, 0 replies; 31+ messages in thread From: Krzysztof Kozlowski @ 2017-03-07 20:17 UTC (permalink / raw) To: linux-arm-kernel On Wed, Feb 22, 2017 at 10:09:54AM +0900, Hoegeun Kwon wrote: > From: Hyungwon Hwang <human.hwang@samsung.com> > > This patch add the panel device tree node for S6E3HA2 display > controller to TM2 dts. > > Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> > Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> > Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> > Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> > Tested-by: Chanwoo Choi <cw00.choi@samsung.com> > --- > arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 12 ++++++++++++ > 1 file changed, 12 insertions(+) I tried to apply but: fatal: corrupt patch at line 37 Patch failed at 0001 arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board Please fix, rebase, add blank link as suggested by Javier and send a v11. Best regards, Krzysztof ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: [PATCH v10 3/3] arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board @ 2017-03-07 20:17 ` Krzysztof Kozlowski 0 siblings, 0 replies; 31+ messages in thread From: Krzysztof Kozlowski @ 2017-03-07 20:17 UTC (permalink / raw) To: Hoegeun Kwon Cc: mark.rutland, devicetree, linux-samsung-soc, cw00.choi, andi.shyti, a.hajda, airlied, catalin.marinas, dri-devel, will.deacon, linux-kernel, robh+dt, jh80.chung, inki.dae, javier, thierry.reding, kgene, linux-arm-kernel On Wed, Feb 22, 2017 at 10:09:54AM +0900, Hoegeun Kwon wrote: > From: Hyungwon Hwang <human.hwang@samsung.com> > > This patch add the panel device tree node for S6E3HA2 display > controller to TM2 dts. > > Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> > Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> > Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> > Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> > Tested-by: Chanwoo Choi <cw00.choi@samsung.com> > --- > arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 12 ++++++++++++ > 1 file changed, 12 insertions(+) I tried to apply but: fatal: corrupt patch at line 37 Patch failed at 0001 arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board Please fix, rebase, add blank link as suggested by Javier and send a v11. Best regards, Krzysztof ^ permalink raw reply [flat|nested] 31+ messages in thread
[parent not found: <CGME20170220071001epcas1p39f8f4b9dcd96c7fb2e808ed3b943dfd3@epcas1p3.samsung.com>]
* [PATCH v10 2/3] drm/panel: Add support for S6E3HA2 panel driver on TM2 board [not found] ` <CGME20170220071001epcas1p39f8f4b9dcd96c7fb2e808ed3b943dfd3@epcas1p3.samsung.com> @ 2017-02-20 7:09 ` Hoegeun Kwon 2017-02-22 1:09 ` Hoegeun Kwon 1 sibling, 0 replies; 31+ messages in thread From: Hoegeun Kwon @ 2017-02-20 7:09 UTC (permalink / raw) To: thierry.reding, airlied, kgene, krzk, robh+dt Cc: dri-devel, linux-kernel, devicetree, linux-samsung-soc, inki.dae, a.hajda, cw00.choi, jh80.chung, andi.shyti, Hoegeun Kwon, Donghwa Lee, Hyungwon Hwang This patch add support for MIPI-DSI based S6E3HA2 AMOLED panel driver. This panel has 1440x2560 resolution in 5.7-inch physical panel in the TM2 device. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> Tested-by: Chanwoo Choi <cw00.choi@samsung.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> --- drivers/gpu/drm/panel/Kconfig | 6 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c | 739 ++++++++++++++++++++++++++ 3 files changed, 746 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig index 62aba97..d913c83 100644 --- a/drivers/gpu/drm/panel/Kconfig +++ b/drivers/gpu/drm/panel/Kconfig @@ -52,6 +52,12 @@ config DRM_PANEL_PANASONIC_VVX10F034N00 WUXGA (1920x1200) Novatek NT1397-based DSI panel as found in some Xperia Z2 tablets +config DRM_PANEL_SAMSUNG_S6E3HA2 + tristate "Samsung S6E3HA2 DSI video mode panel" + depends on OF + depends on DRM_MIPI_DSI + select VIDEOMODE_HELPERS + config DRM_PANEL_SAMSUNG_S6E8AA0 tristate "Samsung S6E8AA0 DSI video mode panel" depends on OF diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile index a5c7ec0..1d483b0 100644 --- a/drivers/gpu/drm/panel/Makefile +++ b/drivers/gpu/drm/panel/Makefile @@ -3,6 +3,7 @@ obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o obj-$(CONFIG_DRM_PANEL_LG_LG4573) += panel-lg-lg4573.o obj-$(CONFIG_DRM_PANEL_PANASONIC_VVX10F034N00) += panel-panasonic-vvx10f034n00.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_LD9040) += panel-samsung-ld9040.o +obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E3HA2) += panel-samsung-s6e3ha2.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E8AA0) += panel-samsung-s6e8aa0.o obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o diff --git a/drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c b/drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c new file mode 100644 index 0000000..4cc08d7 --- /dev/null +++ b/drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c @@ -0,0 +1,739 @@ +/* + * MIPI-DSI based s6e3ha2 AMOLED 5.7 inch panel driver. + * + * Copyright (c) 2016 Samsung Electronics Co., Ltd. + * Donghwa Lee <dh09.lee@samsung.com> + * Hyungwon Hwang <human.hwang@samsung.com> + * Hoegeun Kwon <hoegeun.kwon@samsung.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <drm/drmP.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_panel.h> +#include <linux/backlight.h> +#include <linux/gpio/consumer.h> +#include <linux/regulator/consumer.h> + +#define S6E3HA2_MIN_BRIGHTNESS 0 +#define S6E3HA2_MAX_BRIGHTNESS 100 +#define S6E3HA2_DEFAULT_BRIGHTNESS 80 + +#define S6E3HA2_NUM_GAMMA_STEPS 46 +#define S6E3HA2_GAMMA_CMD_CNT 35 +#define S6E3HA2_VINT_STATUS_MAX 10 + +static const u8 gamma_tbl[S6E3HA2_NUM_GAMMA_STEPS][S6E3HA2_GAMMA_CMD_CNT] = { + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x82, 0x83, + 0x85, 0x88, 0x8b, 0x8b, 0x84, 0x88, 0x82, 0x82, 0x89, 0x86, 0x8c, + 0x94, 0x84, 0xb1, 0xaf, 0x8e, 0xcf, 0xad, 0xc9, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x84, 0x84, + 0x85, 0x87, 0x8b, 0x8a, 0x84, 0x88, 0x82, 0x82, 0x89, 0x86, 0x8a, + 0x93, 0x84, 0xb0, 0xae, 0x8e, 0xc9, 0xa8, 0xc5, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x8a, 0x8a, 0x84, 0x88, 0x81, 0x84, 0x8a, 0x88, 0x8a, + 0x91, 0x84, 0xb1, 0xae, 0x8b, 0xd5, 0xb2, 0xcc, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x8a, 0x8a, 0x84, 0x87, 0x81, 0x84, 0x8a, 0x87, 0x8a, + 0x91, 0x85, 0xae, 0xac, 0x8a, 0xc3, 0xa3, 0xc0, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x85, 0x85, + 0x86, 0x85, 0x88, 0x89, 0x84, 0x89, 0x82, 0x84, 0x87, 0x85, 0x8b, + 0x91, 0x88, 0xad, 0xab, 0x8a, 0xb7, 0x9b, 0xb6, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x89, 0x8a, 0x84, 0x89, 0x83, 0x83, 0x86, 0x84, 0x8b, + 0x90, 0x84, 0xb0, 0xae, 0x8b, 0xce, 0xad, 0xc8, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x87, 0x89, 0x8a, 0x83, 0x87, 0x82, 0x85, 0x88, 0x87, 0x89, + 0x8f, 0x84, 0xac, 0xaa, 0x89, 0xb1, 0x98, 0xaf, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x88, 0x89, 0x84, 0x88, 0x83, 0x82, 0x85, 0x84, 0x8c, + 0x91, 0x86, 0xac, 0xaa, 0x89, 0xc2, 0xa5, 0xbd, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x85, 0x87, 0x89, 0x8a, 0x83, 0x87, 0x82, 0x85, 0x88, 0x87, 0x88, + 0x8b, 0x82, 0xad, 0xaa, 0x8a, 0xc2, 0xa5, 0xbd, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x87, 0x89, 0x84, 0x88, 0x83, 0x82, 0x85, 0x84, 0x8a, + 0x8e, 0x84, 0xae, 0xac, 0x89, 0xda, 0xb7, 0xd0, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x85, 0x86, 0x87, 0x89, 0x84, 0x88, 0x83, 0x80, 0x83, 0x82, 0x8b, + 0x8e, 0x85, 0xac, 0xaa, 0x89, 0xc8, 0xaa, 0xc1, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x85, 0x86, 0x87, 0x89, 0x81, 0x85, 0x81, 0x84, 0x86, 0x84, 0x8c, + 0x8c, 0x84, 0xa9, 0xa8, 0x87, 0xa3, 0x92, 0xa1, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x85, 0x86, 0x87, 0x89, 0x84, 0x86, 0x83, 0x80, 0x83, 0x81, 0x8c, + 0x8d, 0x84, 0xaa, 0xaa, 0x89, 0xce, 0xaf, 0xc5, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x85, 0x86, 0x87, 0x89, 0x81, 0x83, 0x80, 0x83, 0x85, 0x85, 0x8c, + 0x8c, 0x84, 0xa8, 0xa8, 0x88, 0xb5, 0x9f, 0xb0, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x86, 0x86, 0x87, 0x88, 0x81, 0x83, 0x80, 0x83, 0x85, 0x85, 0x8c, + 0x8b, 0x84, 0xab, 0xa8, 0x86, 0xd4, 0xb4, 0xc9, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x86, 0x86, 0x87, 0x88, 0x81, 0x83, 0x80, 0x84, 0x84, 0x85, 0x8b, + 0x8a, 0x83, 0xa6, 0xa5, 0x84, 0xbb, 0xa4, 0xb3, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x86, 0x85, 0x86, 0x86, 0x82, 0x85, 0x81, 0x82, 0x83, 0x84, 0x8e, + 0x8b, 0x83, 0xa4, 0xa3, 0x8a, 0xa1, 0x93, 0x9d, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x87, 0x87, 0x82, 0x85, 0x81, 0x82, 0x82, 0x84, 0x8e, + 0x8b, 0x83, 0xa4, 0xa2, 0x86, 0xc1, 0xa9, 0xb7, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x87, 0x87, 0x82, 0x85, 0x81, 0x82, 0x82, 0x84, 0x8d, + 0x89, 0x82, 0xa2, 0xa1, 0x84, 0xa7, 0x98, 0xa1, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x87, 0x87, 0x82, 0x85, 0x81, 0x83, 0x83, 0x85, 0x8c, + 0x87, 0x7f, 0xa2, 0x9d, 0x88, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xbb, 0x00, 0xc5, 0x00, 0xb4, 0x87, 0x86, 0x86, 0x84, 0x83, + 0x86, 0x87, 0x87, 0x87, 0x80, 0x82, 0x7f, 0x86, 0x86, 0x88, 0x8a, + 0x84, 0x7e, 0x9d, 0x9c, 0x82, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xbd, 0x00, 0xc7, 0x00, 0xb7, 0x87, 0x85, 0x85, 0x84, 0x83, + 0x86, 0x86, 0x86, 0x88, 0x81, 0x83, 0x80, 0x83, 0x84, 0x85, 0x8a, + 0x85, 0x7e, 0x9c, 0x9b, 0x85, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xc0, 0x00, 0xca, 0x00, 0xbb, 0x87, 0x86, 0x85, 0x83, 0x83, + 0x85, 0x86, 0x86, 0x88, 0x81, 0x83, 0x80, 0x84, 0x85, 0x86, 0x89, + 0x83, 0x7d, 0x9c, 0x99, 0x87, 0x7b, 0x7b, 0x7c, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xc4, 0x00, 0xcd, 0x00, 0xbe, 0x87, 0x86, 0x85, 0x83, 0x83, + 0x86, 0x85, 0x85, 0x87, 0x81, 0x82, 0x80, 0x82, 0x82, 0x83, 0x8a, + 0x85, 0x7f, 0x9f, 0x9b, 0x86, 0xb4, 0xa1, 0xac, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xc7, 0x00, 0xd0, 0x00, 0xc2, 0x87, 0x85, 0x85, 0x83, 0x82, + 0x85, 0x85, 0x85, 0x86, 0x82, 0x83, 0x80, 0x82, 0x82, 0x84, 0x87, + 0x86, 0x80, 0x9e, 0x9a, 0x87, 0xa7, 0x98, 0xa1, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xca, 0x00, 0xd2, 0x00, 0xc5, 0x87, 0x85, 0x84, 0x82, 0x82, + 0x84, 0x85, 0x85, 0x86, 0x81, 0x82, 0x7f, 0x82, 0x82, 0x84, 0x88, + 0x86, 0x81, 0x9d, 0x98, 0x86, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xce, 0x00, 0xd6, 0x00, 0xca, 0x86, 0x85, 0x84, 0x83, 0x83, + 0x85, 0x84, 0x84, 0x85, 0x81, 0x82, 0x80, 0x81, 0x81, 0x82, 0x89, + 0x86, 0x81, 0x9c, 0x97, 0x86, 0xa7, 0x98, 0xa1, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xd1, 0x00, 0xd9, 0x00, 0xce, 0x86, 0x84, 0x83, 0x83, 0x82, + 0x85, 0x85, 0x85, 0x86, 0x81, 0x83, 0x81, 0x82, 0x82, 0x83, 0x86, + 0x83, 0x7f, 0x99, 0x95, 0x86, 0xbb, 0xa4, 0xb3, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xd4, 0x00, 0xdb, 0x00, 0xd1, 0x86, 0x85, 0x83, 0x83, 0x82, + 0x85, 0x84, 0x84, 0x85, 0x80, 0x83, 0x82, 0x80, 0x80, 0x81, 0x87, + 0x84, 0x81, 0x98, 0x93, 0x85, 0xae, 0x9c, 0xa8, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xd8, 0x00, 0xde, 0x00, 0xd6, 0x86, 0x84, 0x83, 0x81, 0x81, + 0x83, 0x85, 0x85, 0x85, 0x82, 0x83, 0x81, 0x81, 0x81, 0x83, 0x86, + 0x84, 0x80, 0x98, 0x91, 0x85, 0x7b, 0x7b, 0x7c, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xdc, 0x00, 0xe2, 0x00, 0xda, 0x85, 0x84, 0x83, 0x82, 0x82, + 0x84, 0x84, 0x84, 0x85, 0x81, 0x82, 0x82, 0x80, 0x80, 0x81, 0x83, + 0x82, 0x7f, 0x99, 0x93, 0x86, 0x94, 0x8b, 0x92, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xdf, 0x00, 0xe5, 0x00, 0xde, 0x85, 0x84, 0x82, 0x82, 0x82, + 0x84, 0x83, 0x83, 0x84, 0x81, 0x81, 0x80, 0x83, 0x82, 0x84, 0x82, + 0x81, 0x7f, 0x99, 0x92, 0x86, 0x7b, 0x7b, 0x7c, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x83, 0x83, 0x84, 0x80, 0x81, 0x80, 0x83, 0x83, 0x84, 0x80, + 0x81, 0x7c, 0x99, 0x92, 0x87, 0xa1, 0x93, 0x9d, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x85, 0x84, 0x83, 0x81, 0x81, + 0x82, 0x82, 0x82, 0x83, 0x80, 0x81, 0x80, 0x81, 0x80, 0x82, 0x83, + 0x82, 0x80, 0x91, 0x8d, 0x83, 0x9a, 0x90, 0x96, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x83, 0x83, 0x84, 0x80, 0x81, 0x80, 0x81, 0x80, 0x82, 0x83, + 0x81, 0x7f, 0x91, 0x8c, 0x82, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x83, 0x83, 0x83, 0x82, 0x82, 0x81, 0x81, 0x80, 0x82, 0x82, + 0x82, 0x7f, 0x94, 0x89, 0x84, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x83, 0x83, 0x83, 0x82, 0x82, 0x81, 0x81, 0x80, 0x82, 0x83, + 0x82, 0x7f, 0x91, 0x85, 0x81, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x83, 0x83, 0x83, 0x80, 0x80, 0x7f, 0x83, 0x82, 0x84, 0x83, + 0x82, 0x7f, 0x90, 0x84, 0x81, 0x9a, 0x90, 0x96, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x80, 0x80, + 0x82, 0x83, 0x83, 0x83, 0x80, 0x80, 0x7f, 0x80, 0x80, 0x81, 0x81, + 0x82, 0x83, 0x7e, 0x80, 0x7c, 0xa4, 0x97, 0x9f, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe9, 0x00, 0xec, 0x00, 0xe8, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x82, 0x82, 0x83, 0x7f, 0x7f, 0x7f, 0x81, 0x80, 0x82, 0x83, + 0x83, 0x84, 0x79, 0x7c, 0x79, 0xb1, 0xa0, 0xaa, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xed, 0x00, 0xf0, 0x00, 0xec, 0x83, 0x83, 0x82, 0x80, 0x80, + 0x81, 0x82, 0x82, 0x82, 0x7f, 0x7f, 0x7e, 0x81, 0x81, 0x82, 0x80, + 0x81, 0x81, 0x84, 0x84, 0x83, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xf1, 0x00, 0xf4, 0x00, 0xf1, 0x83, 0x82, 0x82, 0x80, 0x80, + 0x81, 0x82, 0x82, 0x82, 0x80, 0x80, 0x80, 0x80, 0x80, 0x81, 0x7d, + 0x7e, 0x7f, 0x84, 0x84, 0x83, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xf6, 0x00, 0xf7, 0x00, 0xf5, 0x82, 0x82, 0x81, 0x80, 0x80, + 0x80, 0x82, 0x82, 0x82, 0x80, 0x80, 0x80, 0x7f, 0x7f, 0x7f, 0x82, + 0x82, 0x82, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xfa, 0x00, 0xfb, 0x00, 0xfa, 0x81, 0x81, 0x81, 0x80, 0x80, + 0x80, 0x82, 0x82, 0x82, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x01, 0x00, 0x01, 0x00, 0x01, 0x00, 0x80, 0x80, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x01, 0x00, 0x01, 0x00, 0x01, 0x00, 0x80, 0x80, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 } +}; + +unsigned char vint_table[S6E3HA2_VINT_STATUS_MAX] = { + 0x18, 0x19, 0x1a, 0x1b, 0x1c, + 0x1d, 0x1e, 0x1f, 0x20, 0x21 +}; + +struct s6e3ha2 { + struct device *dev; + struct drm_panel panel; + struct backlight_device *bl_dev; + + struct regulator_bulk_data supplies[2]; + struct gpio_desc *reset_gpio; + struct gpio_desc *enable_gpio; +}; + +static int s6e3ha2_dcs_write(struct s6e3ha2 *ctx, const void *data, size_t len) +{ + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); + + return mipi_dsi_dcs_write_buffer(dsi, data, len); +} + +#define s6e3ha2_dcs_write_seq_static(ctx, seq...) do { \ + static const u8 d[] = { seq }; \ + int ret; \ + ret = s6e3ha2_dcs_write(ctx, d, ARRAY_SIZE(d)); \ + if (ret < 0) \ + return ret; \ +} while (0) + +#define s6e3ha2_call_write_func(ret, func) do { \ + ret = (func); \ + if (ret < 0) \ + return ret; \ +} while (0) + +static int s6e3ha2_test_key_on_f0(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xf0, 0x5a, 0x5a); + return 0; +} + +static int s6e3ha2_test_key_off_f0(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xf0, 0xa5, 0xa5); + return 0; +} + +static int s6e3ha2_test_key_on_fc(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xfc, 0x5a, 0x5a); + return 0; +} + +static int s6e3ha2_test_key_off_fc(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xfc, 0xa5, 0xa5); + return 0; +} + +static int s6e3ha2_single_dsi_set(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xf2, 0x67); + s6e3ha2_dcs_write_seq_static(ctx, 0xf9, 0x09); + return 0; +} + +static int s6e3ha2_freq_calibration(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xfd, 0x1c); + s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0x20, 0x39); + s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0xa0); + s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0x20); + s6e3ha2_dcs_write_seq_static(ctx, 0xce, 0x03, 0x3b, 0x12, 0x62, 0x40, + 0x80, 0xc0, 0x28, 0x28, 0x28, 0x28, 0x39, 0xc5); + return 0; +} + +static int s6e3ha2_aor_control(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb2, 0x03, 0x10); + return 0; +} + +static int s6e3ha2_caps_elvss_set(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb6, 0x9c, 0x0a); + return 0; +} + +static int s6e3ha2_acl_off(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0x55, 0x00); + return 0; +} + +static int s6e3ha2_acl_off_opr(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb5, 0x40); + return 0; +} + +static int s6e3ha2_test_global(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb0, 0x07); + return 0; +} + +static int s6e3ha2_test(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb8, 0x19); + return 0; +} + +static int s6e3ha2_touch_hsync_on1(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xbd, 0x33, 0x11, 0x02, + 0x16, 0x02, 0x16); + return 0; +} + +static int s6e3ha2_pentile_control(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xc0, 0x00, 0x00, 0xd8, 0xd8); + return 0; +} + +static int s6e3ha2_poc_global(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb0, 0x20); + return 0; +} + +static int s6e3ha2_poc_setting(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0x08); + return 0; +} + +static int s6e3ha2_pcd_set_off(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xcc, 0x40, 0x51); + return 0; +} + +static int s6e3ha2_err_fg_set(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xed, 0x44); + return 0; +} + +static int s6e3ha2_hbm_off(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0x53, 0x00); + return 0; +} + +static int s6e3ha2_te_start_setting(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb9, 0x10, 0x09, 0xff, 0x00, 0x09); + return 0; +} + +static int s6e3ha2_gamma_update(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xf7, 0x03); + ndelay(100); /* need for 100ns delay */ + s6e3ha2_dcs_write_seq_static(ctx, 0xf7, 0x00); + return 0; +} + +static int s6e3ha2_get_brightness(struct backlight_device *bl_dev) +{ + return bl_dev->props.brightness; +} + +static int s6e3ha2_set_vint(struct s6e3ha2 *ctx) +{ + struct backlight_device *bl_dev = ctx->bl_dev; + unsigned int brightness = bl_dev->props.brightness; + unsigned char data[] = { 0xf4, 0x8b, + vint_table[brightness * (S6E3HA2_VINT_STATUS_MAX - 1) / + S6E3HA2_MAX_BRIGHTNESS] }; + + return s6e3ha2_dcs_write(ctx, data, ARRAY_SIZE(data)); +} + +static unsigned int s6e3ha2_get_brightness_index(unsigned int brightness) +{ + return (brightness * (S6E3HA2_NUM_GAMMA_STEPS - 1)) / + S6E3HA2_MAX_BRIGHTNESS; +} + +static int s6e3ha2_update_gamma(struct s6e3ha2 *ctx, unsigned int brightness) +{ + struct backlight_device *bl_dev = ctx->bl_dev; + unsigned int index = s6e3ha2_get_brightness_index(brightness); + u8 data[S6E3HA2_GAMMA_CMD_CNT + 1] = { 0xca, }; + int ret; + + memcpy(data + 1, gamma_tbl + index, S6E3HA2_GAMMA_CMD_CNT); + s6e3ha2_call_write_func(ret, + s6e3ha2_dcs_write(ctx, data, ARRAY_SIZE(data))); + + s6e3ha2_call_write_func(ret, s6e3ha2_gamma_update(ctx)); + bl_dev->props.brightness = brightness; + + return 0; +} + +static int s6e3ha2_set_brightness(struct backlight_device *bl_dev) +{ + struct s6e3ha2 *ctx = bl_get_data(bl_dev); + unsigned int brightness = bl_dev->props.brightness; + int ret; + + if (brightness < S6E3HA2_MIN_BRIGHTNESS || + brightness > bl_dev->props.max_brightness) { + dev_err(ctx->dev, "Invalid brightness: %u\n", brightness); + return -EINVAL; + } + + if (bl_dev->props.power > FB_BLANK_NORMAL) + return -EPERM; + + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_on_f0(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_update_gamma(ctx, brightness)); + s6e3ha2_call_write_func(ret, s6e3ha2_aor_control(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_set_vint(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_off_f0(ctx)); + + return 0; +} + +static const struct backlight_ops s6e3ha2_bl_ops = { + .get_brightness = s6e3ha2_get_brightness, + .update_status = s6e3ha2_set_brightness, +}; + +static int s6e3ha2_panel_init(struct s6e3ha2 *ctx) +{ + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); + int ret; + + s6e3ha2_call_write_func(ret, mipi_dsi_dcs_exit_sleep_mode(dsi)); + usleep_range(5000, 6000); + + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_on_f0(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_single_dsi_set(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_on_fc(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_freq_calibration(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_off_fc(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_off_f0(ctx)); + + return 0; +} + +static int s6e3ha2_power_off(struct s6e3ha2 *ctx) +{ + return regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies); +} + +static int s6e3ha2_disable(struct drm_panel *panel) +{ + struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel); + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); + int ret; + + s6e3ha2_call_write_func(ret, mipi_dsi_dcs_enter_sleep_mode(dsi)); + s6e3ha2_call_write_func(ret, mipi_dsi_dcs_set_display_off(dsi)); + + msleep(40); + ctx->bl_dev->props.power = FB_BLANK_NORMAL; + + return 0; +} + +static int s6e3ha2_unprepare(struct drm_panel *panel) +{ + struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel); + + return s6e3ha2_power_off(ctx); +} + +static int s6e3ha2_power_on(struct s6e3ha2 *ctx) +{ + int ret; + + ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies); + if (ret < 0) + return ret; + + msleep(120); + + gpiod_set_value(ctx->enable_gpio, 0); + usleep_range(5000, 6000); + gpiod_set_value(ctx->enable_gpio, 1); + + gpiod_set_value(ctx->reset_gpio, 1); + usleep_range(5000, 6000); + gpiod_set_value(ctx->reset_gpio, 0); + usleep_range(5000, 6000); + + return 0; +} +static int s6e3ha2_prepare(struct drm_panel *panel) +{ + struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel); + int ret; + + ret = s6e3ha2_power_on(ctx); + if (ret < 0) + return ret; + + ret = s6e3ha2_panel_init(ctx); + if (ret < 0) + goto err; + + ctx->bl_dev->props.power = FB_BLANK_NORMAL; + + return 0; + +err: + s6e3ha2_power_off(ctx); + return ret; +} + +static int s6e3ha2_enable(struct drm_panel *panel) +{ + struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel); + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); + int ret; + + /* common setting */ + s6e3ha2_call_write_func(ret, + mipi_dsi_dcs_set_tear_on(dsi, MIPI_DSI_DCS_TEAR_MODE_VBLANK)); + + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_on_f0(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_on_fc(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_touch_hsync_on1(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_pentile_control(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_poc_global(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_poc_setting(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_off_fc(ctx)); + + /* pcd setting off for TB */ + s6e3ha2_call_write_func(ret, s6e3ha2_pcd_set_off(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_err_fg_set(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_te_start_setting(ctx)); + + /* brightness setting */ + s6e3ha2_call_write_func(ret, s6e3ha2_set_brightness(ctx->bl_dev)); + s6e3ha2_call_write_func(ret, s6e3ha2_aor_control(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_caps_elvss_set(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_gamma_update(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_acl_off(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_acl_off_opr(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_hbm_off(ctx)); + + /* elvss temp compensation */ + s6e3ha2_call_write_func(ret, s6e3ha2_test_global(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_off_f0(ctx)); + + s6e3ha2_call_write_func(ret, mipi_dsi_dcs_set_display_on(dsi)); + ctx->bl_dev->props.power = FB_BLANK_UNBLANK; + + return 0; +} + +static const struct drm_display_mode default_mode = { + .clock = 222372, + .hdisplay = 1440, + .hsync_start = 1440 + 1, + .hsync_end = 1440 + 1 + 1, + .htotal = 1440 + 1 + 1 + 1, + .vdisplay = 2560, + .vsync_start = 2560 + 1, + .vsync_end = 2560 + 1 + 1, + .vtotal = 2560 + 1 + 1 + 15, + .vrefresh = 60, + .flags = 0, +}; + +static int s6e3ha2_get_modes(struct drm_panel *panel) +{ + struct drm_connector *connector = panel->connector; + struct drm_display_mode *mode; + + mode = drm_mode_duplicate(panel->drm, &default_mode); + if (!mode) { + DRM_ERROR("failed to add mode %ux%ux@%u\n", + default_mode.hdisplay, default_mode.vdisplay, + default_mode.vrefresh); + return -ENOMEM; + } + + drm_mode_set_name(mode); + + mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED; + drm_mode_probed_add(connector, mode); + + connector->display_info.width_mm = 71; + connector->display_info.height_mm = 125; + + return 1; +} + +static const struct drm_panel_funcs s6e3ha2_drm_funcs = { + .disable = s6e3ha2_disable, + .unprepare = s6e3ha2_unprepare, + .prepare = s6e3ha2_prepare, + .enable = s6e3ha2_enable, + .get_modes = s6e3ha2_get_modes, +}; + +static int s6e3ha2_probe(struct mipi_dsi_device *dsi) +{ + struct device *dev = &dsi->dev; + struct s6e3ha2 *ctx; + int ret; + + ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL); + if (!ctx) + return -ENOMEM; + + mipi_dsi_set_drvdata(dsi, ctx); + + ctx->dev = dev; + + dsi->lanes = 4; + dsi->format = MIPI_DSI_FMT_RGB888; + dsi->mode_flags = MIPI_DSI_CLOCK_NON_CONTINUOUS; + + ctx->supplies[0].supply = "vdd3"; + ctx->supplies[1].supply = "vci"; + + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ctx->supplies), + ctx->supplies); + if (ret < 0) { + dev_err(dev, "failed to get regulators: %d\n", ret); + return ret; + } + + ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW); + if (IS_ERR(ctx->reset_gpio)) { + dev_err(dev, "cannot get reset-gpios %ld\n", + PTR_ERR(ctx->reset_gpio)); + return PTR_ERR(ctx->reset_gpio); + } + + ctx->enable_gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_HIGH); + if (IS_ERR(ctx->enable_gpio)) { + dev_err(dev, "cannot get enable-gpios %ld\n", + PTR_ERR(ctx->enable_gpio)); + return PTR_ERR(ctx->enable_gpio); + } + + ctx->bl_dev = backlight_device_register("s6e3ha2", dev, ctx, + &s6e3ha2_bl_ops, NULL); + if (IS_ERR(ctx->bl_dev)) { + dev_err(dev, "failed to register backlight device\n"); + return PTR_ERR(ctx->bl_dev); + } + + ctx->bl_dev->props.max_brightness = S6E3HA2_MAX_BRIGHTNESS; + ctx->bl_dev->props.brightness = S6E3HA2_DEFAULT_BRIGHTNESS; + ctx->bl_dev->props.power = FB_BLANK_POWERDOWN; + + drm_panel_init(&ctx->panel); + ctx->panel.dev = dev; + ctx->panel.funcs = &s6e3ha2_drm_funcs; + + ret = drm_panel_add(&ctx->panel); + if (ret < 0) + goto unregister_backlight; + + ret = mipi_dsi_attach(dsi); + if (ret < 0) + goto remove_panel; + + return ret; + +remove_panel: + drm_panel_remove(&ctx->panel); + +unregister_backlight: + backlight_device_unregister(ctx->bl_dev); + + return ret; +} + +static int s6e3ha2_remove(struct mipi_dsi_device *dsi) +{ + struct s6e3ha2 *ctx = mipi_dsi_get_drvdata(dsi); + + mipi_dsi_detach(dsi); + drm_panel_remove(&ctx->panel); + backlight_device_unregister(ctx->bl_dev); + + return 0; +} + +static const struct of_device_id s6e3ha2_of_match[] = { + { .compatible = "samsung,s6e3ha2" }, + { } +}; +MODULE_DEVICE_TABLE(of, s6e3ha2_of_match); + +static struct mipi_dsi_driver s6e3ha2_driver = { + .probe = s6e3ha2_probe, + .remove = s6e3ha2_remove, + .driver = { + .name = "panel-samsung-s6e3ha2", + .of_match_table = s6e3ha2_of_match, + }, +}; +module_mipi_dsi_driver(s6e3ha2_driver); + +MODULE_AUTHOR("Donghwa Lee <dh09.lee@samsung.com>"); +MODULE_AUTHOR("Hyungwon Hwang <human.hwang@samsung.com>"); +MODULE_AUTHOR("Hoegeun Kwon <hoegeun.kwon@samsung.com>"); +MODULE_DESCRIPTION("MIPI-DSI based s6e3ha2 AMOLED Panel Driver"); +MODULE_LICENSE("GPL v2"); -- 1.9.1 ^ permalink raw reply related [flat|nested] 31+ messages in thread
* [PATCH v10 2/3] drm/panel: Add support for S6E3HA2 panel driver on TM2 board [not found] ` <CGME20170220071001epcas1p39f8f4b9dcd96c7fb2e808ed3b943dfd3@epcas1p3.samsung.com> 2017-02-20 7:09 ` [PATCH v10 2/3] drm/panel: Add support for S6E3HA2 panel driver " Hoegeun Kwon @ 2017-02-22 1:09 ` Hoegeun Kwon 1 sibling, 0 replies; 31+ messages in thread From: Hoegeun Kwon @ 2017-02-22 1:09 UTC (permalink / raw) To: thierry.reding, airlied, robh+dt, mark.rutland, catalin.marinas, will.deacon, kgene, krzk Cc: dri-devel, devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel, javier, inki.dae, a.hajda, cw00.choi, jh80.chung, andi.shyti, Hoegeun Kwon This patch add support for MIPI-DSI based S6E3HA2 AMOLED panel driver. This panel has 1440x2560 resolution in 5.7-inch physical panel in the TM2 device. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> Tested-by: Chanwoo Choi <cw00.choi@samsung.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> --- drivers/gpu/drm/panel/Kconfig | 6 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c | 739 ++++++++++++++++++++++++++ 3 files changed, 746 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig index 62aba97..d913c83 100644 --- a/drivers/gpu/drm/panel/Kconfig +++ b/drivers/gpu/drm/panel/Kconfig @@ -52,6 +52,12 @@ config DRM_PANEL_PANASONIC_VVX10F034N00 WUXGA (1920x1200) Novatek NT1397-based DSI panel as found in some Xperia Z2 tablets +config DRM_PANEL_SAMSUNG_S6E3HA2 + tristate "Samsung S6E3HA2 DSI video mode panel" + depends on OF + depends on DRM_MIPI_DSI + select VIDEOMODE_HELPERS + config DRM_PANEL_SAMSUNG_S6E8AA0 tristate "Samsung S6E8AA0 DSI video mode panel" depends on OF diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile index a5c7ec0..1d483b0 100644 --- a/drivers/gpu/drm/panel/Makefile +++ b/drivers/gpu/drm/panel/Makefile @@ -3,6 +3,7 @@ obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o obj-$(CONFIG_DRM_PANEL_LG_LG4573) += panel-lg-lg4573.o obj-$(CONFIG_DRM_PANEL_PANASONIC_VVX10F034N00) += panel-panasonic-vvx10f034n00.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_LD9040) += panel-samsung-ld9040.o +obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E3HA2) += panel-samsung-s6e3ha2.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E8AA0) += panel-samsung-s6e8aa0.o obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o diff --git a/drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c b/drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c new file mode 100644 index 0000000..4cc08d7 --- /dev/null +++ b/drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c @@ -0,0 +1,739 @@ +/* + * MIPI-DSI based s6e3ha2 AMOLED 5.7 inch panel driver. + * + * Copyright (c) 2016 Samsung Electronics Co., Ltd. + * Donghwa Lee <dh09.lee@samsung.com> + * Hyungwon Hwang <human.hwang@samsung.com> + * Hoegeun Kwon <hoegeun.kwon@samsung.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <drm/drmP.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_panel.h> +#include <linux/backlight.h> +#include <linux/gpio/consumer.h> +#include <linux/regulator/consumer.h> + +#define S6E3HA2_MIN_BRIGHTNESS 0 +#define S6E3HA2_MAX_BRIGHTNESS 100 +#define S6E3HA2_DEFAULT_BRIGHTNESS 80 + +#define S6E3HA2_NUM_GAMMA_STEPS 46 +#define S6E3HA2_GAMMA_CMD_CNT 35 +#define S6E3HA2_VINT_STATUS_MAX 10 + +static const u8 gamma_tbl[S6E3HA2_NUM_GAMMA_STEPS][S6E3HA2_GAMMA_CMD_CNT] = { + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x82, 0x83, + 0x85, 0x88, 0x8b, 0x8b, 0x84, 0x88, 0x82, 0x82, 0x89, 0x86, 0x8c, + 0x94, 0x84, 0xb1, 0xaf, 0x8e, 0xcf, 0xad, 0xc9, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x84, 0x84, + 0x85, 0x87, 0x8b, 0x8a, 0x84, 0x88, 0x82, 0x82, 0x89, 0x86, 0x8a, + 0x93, 0x84, 0xb0, 0xae, 0x8e, 0xc9, 0xa8, 0xc5, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x8a, 0x8a, 0x84, 0x88, 0x81, 0x84, 0x8a, 0x88, 0x8a, + 0x91, 0x84, 0xb1, 0xae, 0x8b, 0xd5, 0xb2, 0xcc, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x8a, 0x8a, 0x84, 0x87, 0x81, 0x84, 0x8a, 0x87, 0x8a, + 0x91, 0x85, 0xae, 0xac, 0x8a, 0xc3, 0xa3, 0xc0, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x85, 0x85, + 0x86, 0x85, 0x88, 0x89, 0x84, 0x89, 0x82, 0x84, 0x87, 0x85, 0x8b, + 0x91, 0x88, 0xad, 0xab, 0x8a, 0xb7, 0x9b, 0xb6, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x89, 0x8a, 0x84, 0x89, 0x83, 0x83, 0x86, 0x84, 0x8b, + 0x90, 0x84, 0xb0, 0xae, 0x8b, 0xce, 0xad, 0xc8, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x87, 0x89, 0x8a, 0x83, 0x87, 0x82, 0x85, 0x88, 0x87, 0x89, + 0x8f, 0x84, 0xac, 0xaa, 0x89, 0xb1, 0x98, 0xaf, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x88, 0x89, 0x84, 0x88, 0x83, 0x82, 0x85, 0x84, 0x8c, + 0x91, 0x86, 0xac, 0xaa, 0x89, 0xc2, 0xa5, 0xbd, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x85, 0x87, 0x89, 0x8a, 0x83, 0x87, 0x82, 0x85, 0x88, 0x87, 0x88, + 0x8b, 0x82, 0xad, 0xaa, 0x8a, 0xc2, 0xa5, 0xbd, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x87, 0x89, 0x84, 0x88, 0x83, 0x82, 0x85, 0x84, 0x8a, + 0x8e, 0x84, 0xae, 0xac, 0x89, 0xda, 0xb7, 0xd0, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x85, 0x86, 0x87, 0x89, 0x84, 0x88, 0x83, 0x80, 0x83, 0x82, 0x8b, + 0x8e, 0x85, 0xac, 0xaa, 0x89, 0xc8, 0xaa, 0xc1, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x85, 0x86, 0x87, 0x89, 0x81, 0x85, 0x81, 0x84, 0x86, 0x84, 0x8c, + 0x8c, 0x84, 0xa9, 0xa8, 0x87, 0xa3, 0x92, 0xa1, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x85, 0x86, 0x87, 0x89, 0x84, 0x86, 0x83, 0x80, 0x83, 0x81, 0x8c, + 0x8d, 0x84, 0xaa, 0xaa, 0x89, 0xce, 0xaf, 0xc5, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x85, 0x86, 0x87, 0x89, 0x81, 0x83, 0x80, 0x83, 0x85, 0x85, 0x8c, + 0x8c, 0x84, 0xa8, 0xa8, 0x88, 0xb5, 0x9f, 0xb0, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x86, 0x86, 0x87, 0x88, 0x81, 0x83, 0x80, 0x83, 0x85, 0x85, 0x8c, + 0x8b, 0x84, 0xab, 0xa8, 0x86, 0xd4, 0xb4, 0xc9, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x86, 0x86, 0x87, 0x88, 0x81, 0x83, 0x80, 0x84, 0x84, 0x85, 0x8b, + 0x8a, 0x83, 0xa6, 0xa5, 0x84, 0xbb, 0xa4, 0xb3, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x86, 0x85, 0x86, 0x86, 0x82, 0x85, 0x81, 0x82, 0x83, 0x84, 0x8e, + 0x8b, 0x83, 0xa4, 0xa3, 0x8a, 0xa1, 0x93, 0x9d, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x87, 0x87, 0x82, 0x85, 0x81, 0x82, 0x82, 0x84, 0x8e, + 0x8b, 0x83, 0xa4, 0xa2, 0x86, 0xc1, 0xa9, 0xb7, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x87, 0x87, 0x82, 0x85, 0x81, 0x82, 0x82, 0x84, 0x8d, + 0x89, 0x82, 0xa2, 0xa1, 0x84, 0xa7, 0x98, 0xa1, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x87, 0x87, 0x82, 0x85, 0x81, 0x83, 0x83, 0x85, 0x8c, + 0x87, 0x7f, 0xa2, 0x9d, 0x88, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xbb, 0x00, 0xc5, 0x00, 0xb4, 0x87, 0x86, 0x86, 0x84, 0x83, + 0x86, 0x87, 0x87, 0x87, 0x80, 0x82, 0x7f, 0x86, 0x86, 0x88, 0x8a, + 0x84, 0x7e, 0x9d, 0x9c, 0x82, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xbd, 0x00, 0xc7, 0x00, 0xb7, 0x87, 0x85, 0x85, 0x84, 0x83, + 0x86, 0x86, 0x86, 0x88, 0x81, 0x83, 0x80, 0x83, 0x84, 0x85, 0x8a, + 0x85, 0x7e, 0x9c, 0x9b, 0x85, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xc0, 0x00, 0xca, 0x00, 0xbb, 0x87, 0x86, 0x85, 0x83, 0x83, + 0x85, 0x86, 0x86, 0x88, 0x81, 0x83, 0x80, 0x84, 0x85, 0x86, 0x89, + 0x83, 0x7d, 0x9c, 0x99, 0x87, 0x7b, 0x7b, 0x7c, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xc4, 0x00, 0xcd, 0x00, 0xbe, 0x87, 0x86, 0x85, 0x83, 0x83, + 0x86, 0x85, 0x85, 0x87, 0x81, 0x82, 0x80, 0x82, 0x82, 0x83, 0x8a, + 0x85, 0x7f, 0x9f, 0x9b, 0x86, 0xb4, 0xa1, 0xac, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xc7, 0x00, 0xd0, 0x00, 0xc2, 0x87, 0x85, 0x85, 0x83, 0x82, + 0x85, 0x85, 0x85, 0x86, 0x82, 0x83, 0x80, 0x82, 0x82, 0x84, 0x87, + 0x86, 0x80, 0x9e, 0x9a, 0x87, 0xa7, 0x98, 0xa1, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xca, 0x00, 0xd2, 0x00, 0xc5, 0x87, 0x85, 0x84, 0x82, 0x82, + 0x84, 0x85, 0x85, 0x86, 0x81, 0x82, 0x7f, 0x82, 0x82, 0x84, 0x88, + 0x86, 0x81, 0x9d, 0x98, 0x86, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xce, 0x00, 0xd6, 0x00, 0xca, 0x86, 0x85, 0x84, 0x83, 0x83, + 0x85, 0x84, 0x84, 0x85, 0x81, 0x82, 0x80, 0x81, 0x81, 0x82, 0x89, + 0x86, 0x81, 0x9c, 0x97, 0x86, 0xa7, 0x98, 0xa1, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xd1, 0x00, 0xd9, 0x00, 0xce, 0x86, 0x84, 0x83, 0x83, 0x82, + 0x85, 0x85, 0x85, 0x86, 0x81, 0x83, 0x81, 0x82, 0x82, 0x83, 0x86, + 0x83, 0x7f, 0x99, 0x95, 0x86, 0xbb, 0xa4, 0xb3, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xd4, 0x00, 0xdb, 0x00, 0xd1, 0x86, 0x85, 0x83, 0x83, 0x82, + 0x85, 0x84, 0x84, 0x85, 0x80, 0x83, 0x82, 0x80, 0x80, 0x81, 0x87, + 0x84, 0x81, 0x98, 0x93, 0x85, 0xae, 0x9c, 0xa8, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xd8, 0x00, 0xde, 0x00, 0xd6, 0x86, 0x84, 0x83, 0x81, 0x81, + 0x83, 0x85, 0x85, 0x85, 0x82, 0x83, 0x81, 0x81, 0x81, 0x83, 0x86, + 0x84, 0x80, 0x98, 0x91, 0x85, 0x7b, 0x7b, 0x7c, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xdc, 0x00, 0xe2, 0x00, 0xda, 0x85, 0x84, 0x83, 0x82, 0x82, + 0x84, 0x84, 0x84, 0x85, 0x81, 0x82, 0x82, 0x80, 0x80, 0x81, 0x83, + 0x82, 0x7f, 0x99, 0x93, 0x86, 0x94, 0x8b, 0x92, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xdf, 0x00, 0xe5, 0x00, 0xde, 0x85, 0x84, 0x82, 0x82, 0x82, + 0x84, 0x83, 0x83, 0x84, 0x81, 0x81, 0x80, 0x83, 0x82, 0x84, 0x82, + 0x81, 0x7f, 0x99, 0x92, 0x86, 0x7b, 0x7b, 0x7c, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x83, 0x83, 0x84, 0x80, 0x81, 0x80, 0x83, 0x83, 0x84, 0x80, + 0x81, 0x7c, 0x99, 0x92, 0x87, 0xa1, 0x93, 0x9d, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x85, 0x84, 0x83, 0x81, 0x81, + 0x82, 0x82, 0x82, 0x83, 0x80, 0x81, 0x80, 0x81, 0x80, 0x82, 0x83, + 0x82, 0x80, 0x91, 0x8d, 0x83, 0x9a, 0x90, 0x96, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x83, 0x83, 0x84, 0x80, 0x81, 0x80, 0x81, 0x80, 0x82, 0x83, + 0x81, 0x7f, 0x91, 0x8c, 0x82, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x83, 0x83, 0x83, 0x82, 0x82, 0x81, 0x81, 0x80, 0x82, 0x82, + 0x82, 0x7f, 0x94, 0x89, 0x84, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x83, 0x83, 0x83, 0x82, 0x82, 0x81, 0x81, 0x80, 0x82, 0x83, + 0x82, 0x7f, 0x91, 0x85, 0x81, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x83, 0x83, 0x83, 0x80, 0x80, 0x7f, 0x83, 0x82, 0x84, 0x83, + 0x82, 0x7f, 0x90, 0x84, 0x81, 0x9a, 0x90, 0x96, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x80, 0x80, + 0x82, 0x83, 0x83, 0x83, 0x80, 0x80, 0x7f, 0x80, 0x80, 0x81, 0x81, + 0x82, 0x83, 0x7e, 0x80, 0x7c, 0xa4, 0x97, 0x9f, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe9, 0x00, 0xec, 0x00, 0xe8, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x82, 0x82, 0x83, 0x7f, 0x7f, 0x7f, 0x81, 0x80, 0x82, 0x83, + 0x83, 0x84, 0x79, 0x7c, 0x79, 0xb1, 0xa0, 0xaa, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xed, 0x00, 0xf0, 0x00, 0xec, 0x83, 0x83, 0x82, 0x80, 0x80, + 0x81, 0x82, 0x82, 0x82, 0x7f, 0x7f, 0x7e, 0x81, 0x81, 0x82, 0x80, + 0x81, 0x81, 0x84, 0x84, 0x83, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xf1, 0x00, 0xf4, 0x00, 0xf1, 0x83, 0x82, 0x82, 0x80, 0x80, + 0x81, 0x82, 0x82, 0x82, 0x80, 0x80, 0x80, 0x80, 0x80, 0x81, 0x7d, + 0x7e, 0x7f, 0x84, 0x84, 0x83, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xf6, 0x00, 0xf7, 0x00, 0xf5, 0x82, 0x82, 0x81, 0x80, 0x80, + 0x80, 0x82, 0x82, 0x82, 0x80, 0x80, 0x80, 0x7f, 0x7f, 0x7f, 0x82, + 0x82, 0x82, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xfa, 0x00, 0xfb, 0x00, 0xfa, 0x81, 0x81, 0x81, 0x80, 0x80, + 0x80, 0x82, 0x82, 0x82, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x01, 0x00, 0x01, 0x00, 0x01, 0x00, 0x80, 0x80, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x01, 0x00, 0x01, 0x00, 0x01, 0x00, 0x80, 0x80, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 } +}; + +unsigned char vint_table[S6E3HA2_VINT_STATUS_MAX] = { + 0x18, 0x19, 0x1a, 0x1b, 0x1c, + 0x1d, 0x1e, 0x1f, 0x20, 0x21 +}; + +struct s6e3ha2 { + struct device *dev; + struct drm_panel panel; + struct backlight_device *bl_dev; + + struct regulator_bulk_data supplies[2]; + struct gpio_desc *reset_gpio; + struct gpio_desc *enable_gpio; +}; + +static int s6e3ha2_dcs_write(struct s6e3ha2 *ctx, const void *data, size_t len) +{ + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); + + return mipi_dsi_dcs_write_buffer(dsi, data, len); +} + +#define s6e3ha2_dcs_write_seq_static(ctx, seq...) do { \ + static const u8 d[] = { seq }; \ + int ret; \ + ret = s6e3ha2_dcs_write(ctx, d, ARRAY_SIZE(d)); \ + if (ret < 0) \ + return ret; \ +} while (0) + +#define s6e3ha2_call_write_func(ret, func) do { \ + ret = (func); \ + if (ret < 0) \ + return ret; \ +} while (0) + +static int s6e3ha2_test_key_on_f0(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xf0, 0x5a, 0x5a); + return 0; +} + +static int s6e3ha2_test_key_off_f0(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xf0, 0xa5, 0xa5); + return 0; +} + +static int s6e3ha2_test_key_on_fc(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xfc, 0x5a, 0x5a); + return 0; +} + +static int s6e3ha2_test_key_off_fc(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xfc, 0xa5, 0xa5); + return 0; +} + +static int s6e3ha2_single_dsi_set(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xf2, 0x67); + s6e3ha2_dcs_write_seq_static(ctx, 0xf9, 0x09); + return 0; +} + +static int s6e3ha2_freq_calibration(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xfd, 0x1c); + s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0x20, 0x39); + s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0xa0); + s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0x20); + s6e3ha2_dcs_write_seq_static(ctx, 0xce, 0x03, 0x3b, 0x12, 0x62, 0x40, + 0x80, 0xc0, 0x28, 0x28, 0x28, 0x28, 0x39, 0xc5); + return 0; +} + +static int s6e3ha2_aor_control(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb2, 0x03, 0x10); + return 0; +} + +static int s6e3ha2_caps_elvss_set(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb6, 0x9c, 0x0a); + return 0; +} + +static int s6e3ha2_acl_off(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0x55, 0x00); + return 0; +} + +static int s6e3ha2_acl_off_opr(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb5, 0x40); + return 0; +} + +static int s6e3ha2_test_global(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb0, 0x07); + return 0; +} + +static int s6e3ha2_test(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb8, 0x19); + return 0; +} + +static int s6e3ha2_touch_hsync_on1(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xbd, 0x33, 0x11, 0x02, + 0x16, 0x02, 0x16); + return 0; +} + +static int s6e3ha2_pentile_control(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xc0, 0x00, 0x00, 0xd8, 0xd8); + return 0; +} + +static int s6e3ha2_poc_global(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb0, 0x20); + return 0; +} + +static int s6e3ha2_poc_setting(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0x08); + return 0; +} + +static int s6e3ha2_pcd_set_off(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xcc, 0x40, 0x51); + return 0; +} + +static int s6e3ha2_err_fg_set(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xed, 0x44); + return 0; +} + +static int s6e3ha2_hbm_off(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0x53, 0x00); + return 0; +} + +static int s6e3ha2_te_start_setting(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb9, 0x10, 0x09, 0xff, 0x00, 0x09); + return 0; +} + +static int s6e3ha2_gamma_update(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xf7, 0x03); + ndelay(100); /* need for 100ns delay */ + s6e3ha2_dcs_write_seq_static(ctx, 0xf7, 0x00); + return 0; +} + +static int s6e3ha2_get_brightness(struct backlight_device *bl_dev) +{ + return bl_dev->props.brightness; +} + +static int s6e3ha2_set_vint(struct s6e3ha2 *ctx) +{ + struct backlight_device *bl_dev = ctx->bl_dev; + unsigned int brightness = bl_dev->props.brightness; + unsigned char data[] = { 0xf4, 0x8b, + vint_table[brightness * (S6E3HA2_VINT_STATUS_MAX - 1) / + S6E3HA2_MAX_BRIGHTNESS] }; + + return s6e3ha2_dcs_write(ctx, data, ARRAY_SIZE(data)); +} + +static unsigned int s6e3ha2_get_brightness_index(unsigned int brightness) +{ + return (brightness * (S6E3HA2_NUM_GAMMA_STEPS - 1)) / + S6E3HA2_MAX_BRIGHTNESS; +} + +static int s6e3ha2_update_gamma(struct s6e3ha2 *ctx, unsigned int brightness) +{ + struct backlight_device *bl_dev = ctx->bl_dev; + unsigned int index = s6e3ha2_get_brightness_index(brightness); + u8 data[S6E3HA2_GAMMA_CMD_CNT + 1] = { 0xca, }; + int ret; + + memcpy(data + 1, gamma_tbl + index, S6E3HA2_GAMMA_CMD_CNT); + s6e3ha2_call_write_func(ret, + s6e3ha2_dcs_write(ctx, data, ARRAY_SIZE(data))); + + s6e3ha2_call_write_func(ret, s6e3ha2_gamma_update(ctx)); + bl_dev->props.brightness = brightness; + + return 0; +} + +static int s6e3ha2_set_brightness(struct backlight_device *bl_dev) +{ + struct s6e3ha2 *ctx = bl_get_data(bl_dev); + unsigned int brightness = bl_dev->props.brightness; + int ret; + + if (brightness < S6E3HA2_MIN_BRIGHTNESS || + brightness > bl_dev->props.max_brightness) { + dev_err(ctx->dev, "Invalid brightness: %u\n", brightness); + return -EINVAL; + } + + if (bl_dev->props.power > FB_BLANK_NORMAL) + return -EPERM; + + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_on_f0(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_update_gamma(ctx, brightness)); + s6e3ha2_call_write_func(ret, s6e3ha2_aor_control(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_set_vint(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_off_f0(ctx)); + + return 0; +} + +static const struct backlight_ops s6e3ha2_bl_ops = { + .get_brightness = s6e3ha2_get_brightness, + .update_status = s6e3ha2_set_brightness, +}; + +static int s6e3ha2_panel_init(struct s6e3ha2 *ctx) +{ + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); + int ret; + + s6e3ha2_call_write_func(ret, mipi_dsi_dcs_exit_sleep_mode(dsi)); + usleep_range(5000, 6000); + + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_on_f0(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_single_dsi_set(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_on_fc(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_freq_calibration(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_off_fc(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_off_f0(ctx)); + + return 0; +} + +static int s6e3ha2_power_off(struct s6e3ha2 *ctx) +{ + return regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies); +} + +static int s6e3ha2_disable(struct drm_panel *panel) +{ + struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel); + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); + int ret; + + s6e3ha2_call_write_func(ret, mipi_dsi_dcs_enter_sleep_mode(dsi)); + s6e3ha2_call_write_func(ret, mipi_dsi_dcs_set_display_off(dsi)); + + msleep(40); + ctx->bl_dev->props.power = FB_BLANK_NORMAL; + + return 0; +} + +static int s6e3ha2_unprepare(struct drm_panel *panel) +{ + struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel); + + return s6e3ha2_power_off(ctx); +} + +static int s6e3ha2_power_on(struct s6e3ha2 *ctx) +{ + int ret; + + ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies); + if (ret < 0) + return ret; + + msleep(120); + + gpiod_set_value(ctx->enable_gpio, 0); + usleep_range(5000, 6000); + gpiod_set_value(ctx->enable_gpio, 1); + + gpiod_set_value(ctx->reset_gpio, 1); + usleep_range(5000, 6000); + gpiod_set_value(ctx->reset_gpio, 0); + usleep_range(5000, 6000); + + return 0; +} +static int s6e3ha2_prepare(struct drm_panel *panel) +{ + struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel); + int ret; + + ret = s6e3ha2_power_on(ctx); + if (ret < 0) + return ret; + + ret = s6e3ha2_panel_init(ctx); + if (ret < 0) + goto err; + + ctx->bl_dev->props.power = FB_BLANK_NORMAL; + + return 0; + +err: + s6e3ha2_power_off(ctx); + return ret; +} + +static int s6e3ha2_enable(struct drm_panel *panel) +{ + struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel); + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); + int ret; + + /* common setting */ + s6e3ha2_call_write_func(ret, + mipi_dsi_dcs_set_tear_on(dsi, MIPI_DSI_DCS_TEAR_MODE_VBLANK)); + + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_on_f0(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_on_fc(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_touch_hsync_on1(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_pentile_control(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_poc_global(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_poc_setting(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_off_fc(ctx)); + + /* pcd setting off for TB */ + s6e3ha2_call_write_func(ret, s6e3ha2_pcd_set_off(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_err_fg_set(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_te_start_setting(ctx)); + + /* brightness setting */ + s6e3ha2_call_write_func(ret, s6e3ha2_set_brightness(ctx->bl_dev)); + s6e3ha2_call_write_func(ret, s6e3ha2_aor_control(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_caps_elvss_set(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_gamma_update(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_acl_off(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_acl_off_opr(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_hbm_off(ctx)); + + /* elvss temp compensation */ + s6e3ha2_call_write_func(ret, s6e3ha2_test_global(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_off_f0(ctx)); + + s6e3ha2_call_write_func(ret, mipi_dsi_dcs_set_display_on(dsi)); + ctx->bl_dev->props.power = FB_BLANK_UNBLANK; + + return 0; +} + +static const struct drm_display_mode default_mode = { + .clock = 222372, + .hdisplay = 1440, + .hsync_start = 1440 + 1, + .hsync_end = 1440 + 1 + 1, + .htotal = 1440 + 1 + 1 + 1, + .vdisplay = 2560, + .vsync_start = 2560 + 1, + .vsync_end = 2560 + 1 + 1, + .vtotal = 2560 + 1 + 1 + 15, + .vrefresh = 60, + .flags = 0, +}; + +static int s6e3ha2_get_modes(struct drm_panel *panel) +{ + struct drm_connector *connector = panel->connector; + struct drm_display_mode *mode; + + mode = drm_mode_duplicate(panel->drm, &default_mode); + if (!mode) { + DRM_ERROR("failed to add mode %ux%ux@%u\n", + default_mode.hdisplay, default_mode.vdisplay, + default_mode.vrefresh); + return -ENOMEM; + } + + drm_mode_set_name(mode); + + mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED; + drm_mode_probed_add(connector, mode); + + connector->display_info.width_mm = 71; + connector->display_info.height_mm = 125; + + return 1; +} + +static const struct drm_panel_funcs s6e3ha2_drm_funcs = { + .disable = s6e3ha2_disable, + .unprepare = s6e3ha2_unprepare, + .prepare = s6e3ha2_prepare, + .enable = s6e3ha2_enable, + .get_modes = s6e3ha2_get_modes, +}; + +static int s6e3ha2_probe(struct mipi_dsi_device *dsi) +{ + struct device *dev = &dsi->dev; + struct s6e3ha2 *ctx; + int ret; + + ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL); + if (!ctx) + return -ENOMEM; + + mipi_dsi_set_drvdata(dsi, ctx); + + ctx->dev = dev; + + dsi->lanes = 4; + dsi->format = MIPI_DSI_FMT_RGB888; + dsi->mode_flags = MIPI_DSI_CLOCK_NON_CONTINUOUS; + + ctx->supplies[0].supply = "vdd3"; + ctx->supplies[1].supply = "vci"; + + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ctx->supplies), + ctx->supplies); + if (ret < 0) { + dev_err(dev, "failed to get regulators: %d\n", ret); + return ret; + } + + ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW); + if (IS_ERR(ctx->reset_gpio)) { + dev_err(dev, "cannot get reset-gpios %ld\n", + PTR_ERR(ctx->reset_gpio)); + return PTR_ERR(ctx->reset_gpio); + } + + ctx->enable_gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_HIGH); + if (IS_ERR(ctx->enable_gpio)) { + dev_err(dev, "cannot get enable-gpios %ld\n", + PTR_ERR(ctx->enable_gpio)); + return PTR_ERR(ctx->enable_gpio); + } + + ctx->bl_dev = backlight_device_register("s6e3ha2", dev, ctx, + &s6e3ha2_bl_ops, NULL); + if (IS_ERR(ctx->bl_dev)) { + dev_err(dev, "failed to register backlight device\n"); + return PTR_ERR(ctx->bl_dev); + } + + ctx->bl_dev->props.max_brightness = S6E3HA2_MAX_BRIGHTNESS; + ctx->bl_dev->props.brightness = S6E3HA2_DEFAULT_BRIGHTNESS; + ctx->bl_dev->props.power = FB_BLANK_POWERDOWN; + + drm_panel_init(&ctx->panel); + ctx->panel.dev = dev; + ctx->panel.funcs = &s6e3ha2_drm_funcs; + + ret = drm_panel_add(&ctx->panel); + if (ret < 0) + goto unregister_backlight; + + ret = mipi_dsi_attach(dsi); + if (ret < 0) + goto remove_panel; + + return ret; + +remove_panel: + drm_panel_remove(&ctx->panel); + +unregister_backlight: + backlight_device_unregister(ctx->bl_dev); + + return ret; +} + +static int s6e3ha2_remove(struct mipi_dsi_device *dsi) +{ + struct s6e3ha2 *ctx = mipi_dsi_get_drvdata(dsi); + + mipi_dsi_detach(dsi); + drm_panel_remove(&ctx->panel); + backlight_device_unregister(ctx->bl_dev); + + return 0; +} + +static const struct of_device_id s6e3ha2_of_match[] = { + { .compatible = "samsung,s6e3ha2" }, + { } +}; +MODULE_DEVICE_TABLE(of, s6e3ha2_of_match); + +static struct mipi_dsi_driver s6e3ha2_driver = { + .probe = s6e3ha2_probe, + .remove = s6e3ha2_remove, + .driver = { + .name = "panel-samsung-s6e3ha2", + .of_match_table = s6e3ha2_of_match, + }, +}; +module_mipi_dsi_driver(s6e3ha2_driver); + +MODULE_AUTHOR("Donghwa Lee <dh09.lee@samsung.com>"); +MODULE_AUTHOR("Hyungwon Hwang <human.hwang@samsung.com>"); +MODULE_AUTHOR("Hoegeun Kwon <hoegeun.kwon@samsung.com>"); +MODULE_DESCRIPTION("MIPI-DSI based s6e3ha2 AMOLED Panel Driver"); +MODULE_LICENSE("GPL v2"); -- 1.9.1 ^ permalink raw reply related [flat|nested] 31+ messages in thread
* [PATCH v10 2/3] drm/panel: Add support for S6E3HA2 panel driver on TM2 board @ 2017-02-22 1:09 ` Hoegeun Kwon 0 siblings, 0 replies; 31+ messages in thread From: Hoegeun Kwon @ 2017-02-22 1:09 UTC (permalink / raw) To: linux-arm-kernel This patch add support for MIPI-DSI based S6E3HA2 AMOLED panel driver. This panel has 1440x2560 resolution in 5.7-inch physical panel in the TM2 device. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> Tested-by: Chanwoo Choi <cw00.choi@samsung.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> --- drivers/gpu/drm/panel/Kconfig | 6 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c | 739 ++++++++++++++++++++++++++ 3 files changed, 746 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig index 62aba97..d913c83 100644 --- a/drivers/gpu/drm/panel/Kconfig +++ b/drivers/gpu/drm/panel/Kconfig @@ -52,6 +52,12 @@ config DRM_PANEL_PANASONIC_VVX10F034N00 WUXGA (1920x1200) Novatek NT1397-based DSI panel as found in some Xperia Z2 tablets +config DRM_PANEL_SAMSUNG_S6E3HA2 + tristate "Samsung S6E3HA2 DSI video mode panel" + depends on OF + depends on DRM_MIPI_DSI + select VIDEOMODE_HELPERS + config DRM_PANEL_SAMSUNG_S6E8AA0 tristate "Samsung S6E8AA0 DSI video mode panel" depends on OF diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile index a5c7ec0..1d483b0 100644 --- a/drivers/gpu/drm/panel/Makefile +++ b/drivers/gpu/drm/panel/Makefile @@ -3,6 +3,7 @@ obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o obj-$(CONFIG_DRM_PANEL_LG_LG4573) += panel-lg-lg4573.o obj-$(CONFIG_DRM_PANEL_PANASONIC_VVX10F034N00) += panel-panasonic-vvx10f034n00.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_LD9040) += panel-samsung-ld9040.o +obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E3HA2) += panel-samsung-s6e3ha2.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E8AA0) += panel-samsung-s6e8aa0.o obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o diff --git a/drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c b/drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c new file mode 100644 index 0000000..4cc08d7 --- /dev/null +++ b/drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c @@ -0,0 +1,739 @@ +/* + * MIPI-DSI based s6e3ha2 AMOLED 5.7 inch panel driver. + * + * Copyright (c) 2016 Samsung Electronics Co., Ltd. + * Donghwa Lee <dh09.lee@samsung.com> + * Hyungwon Hwang <human.hwang@samsung.com> + * Hoegeun Kwon <hoegeun.kwon@samsung.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <drm/drmP.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_panel.h> +#include <linux/backlight.h> +#include <linux/gpio/consumer.h> +#include <linux/regulator/consumer.h> + +#define S6E3HA2_MIN_BRIGHTNESS 0 +#define S6E3HA2_MAX_BRIGHTNESS 100 +#define S6E3HA2_DEFAULT_BRIGHTNESS 80 + +#define S6E3HA2_NUM_GAMMA_STEPS 46 +#define S6E3HA2_GAMMA_CMD_CNT 35 +#define S6E3HA2_VINT_STATUS_MAX 10 + +static const u8 gamma_tbl[S6E3HA2_NUM_GAMMA_STEPS][S6E3HA2_GAMMA_CMD_CNT] = { + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x82, 0x83, + 0x85, 0x88, 0x8b, 0x8b, 0x84, 0x88, 0x82, 0x82, 0x89, 0x86, 0x8c, + 0x94, 0x84, 0xb1, 0xaf, 0x8e, 0xcf, 0xad, 0xc9, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x84, 0x84, + 0x85, 0x87, 0x8b, 0x8a, 0x84, 0x88, 0x82, 0x82, 0x89, 0x86, 0x8a, + 0x93, 0x84, 0xb0, 0xae, 0x8e, 0xc9, 0xa8, 0xc5, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x8a, 0x8a, 0x84, 0x88, 0x81, 0x84, 0x8a, 0x88, 0x8a, + 0x91, 0x84, 0xb1, 0xae, 0x8b, 0xd5, 0xb2, 0xcc, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x8a, 0x8a, 0x84, 0x87, 0x81, 0x84, 0x8a, 0x87, 0x8a, + 0x91, 0x85, 0xae, 0xac, 0x8a, 0xc3, 0xa3, 0xc0, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x85, 0x85, + 0x86, 0x85, 0x88, 0x89, 0x84, 0x89, 0x82, 0x84, 0x87, 0x85, 0x8b, + 0x91, 0x88, 0xad, 0xab, 0x8a, 0xb7, 0x9b, 0xb6, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x89, 0x8a, 0x84, 0x89, 0x83, 0x83, 0x86, 0x84, 0x8b, + 0x90, 0x84, 0xb0, 0xae, 0x8b, 0xce, 0xad, 0xc8, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x87, 0x89, 0x8a, 0x83, 0x87, 0x82, 0x85, 0x88, 0x87, 0x89, + 0x8f, 0x84, 0xac, 0xaa, 0x89, 0xb1, 0x98, 0xaf, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x88, 0x89, 0x84, 0x88, 0x83, 0x82, 0x85, 0x84, 0x8c, + 0x91, 0x86, 0xac, 0xaa, 0x89, 0xc2, 0xa5, 0xbd, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x85, 0x87, 0x89, 0x8a, 0x83, 0x87, 0x82, 0x85, 0x88, 0x87, 0x88, + 0x8b, 0x82, 0xad, 0xaa, 0x8a, 0xc2, 0xa5, 0xbd, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x87, 0x89, 0x84, 0x88, 0x83, 0x82, 0x85, 0x84, 0x8a, + 0x8e, 0x84, 0xae, 0xac, 0x89, 0xda, 0xb7, 0xd0, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x85, 0x86, 0x87, 0x89, 0x84, 0x88, 0x83, 0x80, 0x83, 0x82, 0x8b, + 0x8e, 0x85, 0xac, 0xaa, 0x89, 0xc8, 0xaa, 0xc1, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x85, 0x86, 0x87, 0x89, 0x81, 0x85, 0x81, 0x84, 0x86, 0x84, 0x8c, + 0x8c, 0x84, 0xa9, 0xa8, 0x87, 0xa3, 0x92, 0xa1, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x85, 0x86, 0x87, 0x89, 0x84, 0x86, 0x83, 0x80, 0x83, 0x81, 0x8c, + 0x8d, 0x84, 0xaa, 0xaa, 0x89, 0xce, 0xaf, 0xc5, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x85, 0x86, 0x87, 0x89, 0x81, 0x83, 0x80, 0x83, 0x85, 0x85, 0x8c, + 0x8c, 0x84, 0xa8, 0xa8, 0x88, 0xb5, 0x9f, 0xb0, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x86, 0x86, 0x87, 0x88, 0x81, 0x83, 0x80, 0x83, 0x85, 0x85, 0x8c, + 0x8b, 0x84, 0xab, 0xa8, 0x86, 0xd4, 0xb4, 0xc9, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x86, 0x86, 0x87, 0x88, 0x81, 0x83, 0x80, 0x84, 0x84, 0x85, 0x8b, + 0x8a, 0x83, 0xa6, 0xa5, 0x84, 0xbb, 0xa4, 0xb3, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x86, 0x85, 0x86, 0x86, 0x82, 0x85, 0x81, 0x82, 0x83, 0x84, 0x8e, + 0x8b, 0x83, 0xa4, 0xa3, 0x8a, 0xa1, 0x93, 0x9d, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x87, 0x87, 0x82, 0x85, 0x81, 0x82, 0x82, 0x84, 0x8e, + 0x8b, 0x83, 0xa4, 0xa2, 0x86, 0xc1, 0xa9, 0xb7, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x87, 0x87, 0x82, 0x85, 0x81, 0x82, 0x82, 0x84, 0x8d, + 0x89, 0x82, 0xa2, 0xa1, 0x84, 0xa7, 0x98, 0xa1, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x87, 0x87, 0x82, 0x85, 0x81, 0x83, 0x83, 0x85, 0x8c, + 0x87, 0x7f, 0xa2, 0x9d, 0x88, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xbb, 0x00, 0xc5, 0x00, 0xb4, 0x87, 0x86, 0x86, 0x84, 0x83, + 0x86, 0x87, 0x87, 0x87, 0x80, 0x82, 0x7f, 0x86, 0x86, 0x88, 0x8a, + 0x84, 0x7e, 0x9d, 0x9c, 0x82, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xbd, 0x00, 0xc7, 0x00, 0xb7, 0x87, 0x85, 0x85, 0x84, 0x83, + 0x86, 0x86, 0x86, 0x88, 0x81, 0x83, 0x80, 0x83, 0x84, 0x85, 0x8a, + 0x85, 0x7e, 0x9c, 0x9b, 0x85, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xc0, 0x00, 0xca, 0x00, 0xbb, 0x87, 0x86, 0x85, 0x83, 0x83, + 0x85, 0x86, 0x86, 0x88, 0x81, 0x83, 0x80, 0x84, 0x85, 0x86, 0x89, + 0x83, 0x7d, 0x9c, 0x99, 0x87, 0x7b, 0x7b, 0x7c, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xc4, 0x00, 0xcd, 0x00, 0xbe, 0x87, 0x86, 0x85, 0x83, 0x83, + 0x86, 0x85, 0x85, 0x87, 0x81, 0x82, 0x80, 0x82, 0x82, 0x83, 0x8a, + 0x85, 0x7f, 0x9f, 0x9b, 0x86, 0xb4, 0xa1, 0xac, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xc7, 0x00, 0xd0, 0x00, 0xc2, 0x87, 0x85, 0x85, 0x83, 0x82, + 0x85, 0x85, 0x85, 0x86, 0x82, 0x83, 0x80, 0x82, 0x82, 0x84, 0x87, + 0x86, 0x80, 0x9e, 0x9a, 0x87, 0xa7, 0x98, 0xa1, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xca, 0x00, 0xd2, 0x00, 0xc5, 0x87, 0x85, 0x84, 0x82, 0x82, + 0x84, 0x85, 0x85, 0x86, 0x81, 0x82, 0x7f, 0x82, 0x82, 0x84, 0x88, + 0x86, 0x81, 0x9d, 0x98, 0x86, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xce, 0x00, 0xd6, 0x00, 0xca, 0x86, 0x85, 0x84, 0x83, 0x83, + 0x85, 0x84, 0x84, 0x85, 0x81, 0x82, 0x80, 0x81, 0x81, 0x82, 0x89, + 0x86, 0x81, 0x9c, 0x97, 0x86, 0xa7, 0x98, 0xa1, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xd1, 0x00, 0xd9, 0x00, 0xce, 0x86, 0x84, 0x83, 0x83, 0x82, + 0x85, 0x85, 0x85, 0x86, 0x81, 0x83, 0x81, 0x82, 0x82, 0x83, 0x86, + 0x83, 0x7f, 0x99, 0x95, 0x86, 0xbb, 0xa4, 0xb3, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xd4, 0x00, 0xdb, 0x00, 0xd1, 0x86, 0x85, 0x83, 0x83, 0x82, + 0x85, 0x84, 0x84, 0x85, 0x80, 0x83, 0x82, 0x80, 0x80, 0x81, 0x87, + 0x84, 0x81, 0x98, 0x93, 0x85, 0xae, 0x9c, 0xa8, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xd8, 0x00, 0xde, 0x00, 0xd6, 0x86, 0x84, 0x83, 0x81, 0x81, + 0x83, 0x85, 0x85, 0x85, 0x82, 0x83, 0x81, 0x81, 0x81, 0x83, 0x86, + 0x84, 0x80, 0x98, 0x91, 0x85, 0x7b, 0x7b, 0x7c, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xdc, 0x00, 0xe2, 0x00, 0xda, 0x85, 0x84, 0x83, 0x82, 0x82, + 0x84, 0x84, 0x84, 0x85, 0x81, 0x82, 0x82, 0x80, 0x80, 0x81, 0x83, + 0x82, 0x7f, 0x99, 0x93, 0x86, 0x94, 0x8b, 0x92, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xdf, 0x00, 0xe5, 0x00, 0xde, 0x85, 0x84, 0x82, 0x82, 0x82, + 0x84, 0x83, 0x83, 0x84, 0x81, 0x81, 0x80, 0x83, 0x82, 0x84, 0x82, + 0x81, 0x7f, 0x99, 0x92, 0x86, 0x7b, 0x7b, 0x7c, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x83, 0x83, 0x84, 0x80, 0x81, 0x80, 0x83, 0x83, 0x84, 0x80, + 0x81, 0x7c, 0x99, 0x92, 0x87, 0xa1, 0x93, 0x9d, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x85, 0x84, 0x83, 0x81, 0x81, + 0x82, 0x82, 0x82, 0x83, 0x80, 0x81, 0x80, 0x81, 0x80, 0x82, 0x83, + 0x82, 0x80, 0x91, 0x8d, 0x83, 0x9a, 0x90, 0x96, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x83, 0x83, 0x84, 0x80, 0x81, 0x80, 0x81, 0x80, 0x82, 0x83, + 0x81, 0x7f, 0x91, 0x8c, 0x82, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x83, 0x83, 0x83, 0x82, 0x82, 0x81, 0x81, 0x80, 0x82, 0x82, + 0x82, 0x7f, 0x94, 0x89, 0x84, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x83, 0x83, 0x83, 0x82, 0x82, 0x81, 0x81, 0x80, 0x82, 0x83, + 0x82, 0x7f, 0x91, 0x85, 0x81, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x83, 0x83, 0x83, 0x80, 0x80, 0x7f, 0x83, 0x82, 0x84, 0x83, + 0x82, 0x7f, 0x90, 0x84, 0x81, 0x9a, 0x90, 0x96, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x80, 0x80, + 0x82, 0x83, 0x83, 0x83, 0x80, 0x80, 0x7f, 0x80, 0x80, 0x81, 0x81, + 0x82, 0x83, 0x7e, 0x80, 0x7c, 0xa4, 0x97, 0x9f, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe9, 0x00, 0xec, 0x00, 0xe8, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x82, 0x82, 0x83, 0x7f, 0x7f, 0x7f, 0x81, 0x80, 0x82, 0x83, + 0x83, 0x84, 0x79, 0x7c, 0x79, 0xb1, 0xa0, 0xaa, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xed, 0x00, 0xf0, 0x00, 0xec, 0x83, 0x83, 0x82, 0x80, 0x80, + 0x81, 0x82, 0x82, 0x82, 0x7f, 0x7f, 0x7e, 0x81, 0x81, 0x82, 0x80, + 0x81, 0x81, 0x84, 0x84, 0x83, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xf1, 0x00, 0xf4, 0x00, 0xf1, 0x83, 0x82, 0x82, 0x80, 0x80, + 0x81, 0x82, 0x82, 0x82, 0x80, 0x80, 0x80, 0x80, 0x80, 0x81, 0x7d, + 0x7e, 0x7f, 0x84, 0x84, 0x83, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xf6, 0x00, 0xf7, 0x00, 0xf5, 0x82, 0x82, 0x81, 0x80, 0x80, + 0x80, 0x82, 0x82, 0x82, 0x80, 0x80, 0x80, 0x7f, 0x7f, 0x7f, 0x82, + 0x82, 0x82, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xfa, 0x00, 0xfb, 0x00, 0xfa, 0x81, 0x81, 0x81, 0x80, 0x80, + 0x80, 0x82, 0x82, 0x82, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x01, 0x00, 0x01, 0x00, 0x01, 0x00, 0x80, 0x80, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x01, 0x00, 0x01, 0x00, 0x01, 0x00, 0x80, 0x80, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 } +}; + +unsigned char vint_table[S6E3HA2_VINT_STATUS_MAX] = { + 0x18, 0x19, 0x1a, 0x1b, 0x1c, + 0x1d, 0x1e, 0x1f, 0x20, 0x21 +}; + +struct s6e3ha2 { + struct device *dev; + struct drm_panel panel; + struct backlight_device *bl_dev; + + struct regulator_bulk_data supplies[2]; + struct gpio_desc *reset_gpio; + struct gpio_desc *enable_gpio; +}; + +static int s6e3ha2_dcs_write(struct s6e3ha2 *ctx, const void *data, size_t len) +{ + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); + + return mipi_dsi_dcs_write_buffer(dsi, data, len); +} + +#define s6e3ha2_dcs_write_seq_static(ctx, seq...) do { \ + static const u8 d[] = { seq }; \ + int ret; \ + ret = s6e3ha2_dcs_write(ctx, d, ARRAY_SIZE(d)); \ + if (ret < 0) \ + return ret; \ +} while (0) + +#define s6e3ha2_call_write_func(ret, func) do { \ + ret = (func); \ + if (ret < 0) \ + return ret; \ +} while (0) + +static int s6e3ha2_test_key_on_f0(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xf0, 0x5a, 0x5a); + return 0; +} + +static int s6e3ha2_test_key_off_f0(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xf0, 0xa5, 0xa5); + return 0; +} + +static int s6e3ha2_test_key_on_fc(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xfc, 0x5a, 0x5a); + return 0; +} + +static int s6e3ha2_test_key_off_fc(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xfc, 0xa5, 0xa5); + return 0; +} + +static int s6e3ha2_single_dsi_set(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xf2, 0x67); + s6e3ha2_dcs_write_seq_static(ctx, 0xf9, 0x09); + return 0; +} + +static int s6e3ha2_freq_calibration(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xfd, 0x1c); + s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0x20, 0x39); + s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0xa0); + s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0x20); + s6e3ha2_dcs_write_seq_static(ctx, 0xce, 0x03, 0x3b, 0x12, 0x62, 0x40, + 0x80, 0xc0, 0x28, 0x28, 0x28, 0x28, 0x39, 0xc5); + return 0; +} + +static int s6e3ha2_aor_control(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb2, 0x03, 0x10); + return 0; +} + +static int s6e3ha2_caps_elvss_set(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb6, 0x9c, 0x0a); + return 0; +} + +static int s6e3ha2_acl_off(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0x55, 0x00); + return 0; +} + +static int s6e3ha2_acl_off_opr(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb5, 0x40); + return 0; +} + +static int s6e3ha2_test_global(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb0, 0x07); + return 0; +} + +static int s6e3ha2_test(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb8, 0x19); + return 0; +} + +static int s6e3ha2_touch_hsync_on1(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xbd, 0x33, 0x11, 0x02, + 0x16, 0x02, 0x16); + return 0; +} + +static int s6e3ha2_pentile_control(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xc0, 0x00, 0x00, 0xd8, 0xd8); + return 0; +} + +static int s6e3ha2_poc_global(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb0, 0x20); + return 0; +} + +static int s6e3ha2_poc_setting(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0x08); + return 0; +} + +static int s6e3ha2_pcd_set_off(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xcc, 0x40, 0x51); + return 0; +} + +static int s6e3ha2_err_fg_set(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xed, 0x44); + return 0; +} + +static int s6e3ha2_hbm_off(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0x53, 0x00); + return 0; +} + +static int s6e3ha2_te_start_setting(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb9, 0x10, 0x09, 0xff, 0x00, 0x09); + return 0; +} + +static int s6e3ha2_gamma_update(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xf7, 0x03); + ndelay(100); /* need for 100ns delay */ + s6e3ha2_dcs_write_seq_static(ctx, 0xf7, 0x00); + return 0; +} + +static int s6e3ha2_get_brightness(struct backlight_device *bl_dev) +{ + return bl_dev->props.brightness; +} + +static int s6e3ha2_set_vint(struct s6e3ha2 *ctx) +{ + struct backlight_device *bl_dev = ctx->bl_dev; + unsigned int brightness = bl_dev->props.brightness; + unsigned char data[] = { 0xf4, 0x8b, + vint_table[brightness * (S6E3HA2_VINT_STATUS_MAX - 1) / + S6E3HA2_MAX_BRIGHTNESS] }; + + return s6e3ha2_dcs_write(ctx, data, ARRAY_SIZE(data)); +} + +static unsigned int s6e3ha2_get_brightness_index(unsigned int brightness) +{ + return (brightness * (S6E3HA2_NUM_GAMMA_STEPS - 1)) / + S6E3HA2_MAX_BRIGHTNESS; +} + +static int s6e3ha2_update_gamma(struct s6e3ha2 *ctx, unsigned int brightness) +{ + struct backlight_device *bl_dev = ctx->bl_dev; + unsigned int index = s6e3ha2_get_brightness_index(brightness); + u8 data[S6E3HA2_GAMMA_CMD_CNT + 1] = { 0xca, }; + int ret; + + memcpy(data + 1, gamma_tbl + index, S6E3HA2_GAMMA_CMD_CNT); + s6e3ha2_call_write_func(ret, + s6e3ha2_dcs_write(ctx, data, ARRAY_SIZE(data))); + + s6e3ha2_call_write_func(ret, s6e3ha2_gamma_update(ctx)); + bl_dev->props.brightness = brightness; + + return 0; +} + +static int s6e3ha2_set_brightness(struct backlight_device *bl_dev) +{ + struct s6e3ha2 *ctx = bl_get_data(bl_dev); + unsigned int brightness = bl_dev->props.brightness; + int ret; + + if (brightness < S6E3HA2_MIN_BRIGHTNESS || + brightness > bl_dev->props.max_brightness) { + dev_err(ctx->dev, "Invalid brightness: %u\n", brightness); + return -EINVAL; + } + + if (bl_dev->props.power > FB_BLANK_NORMAL) + return -EPERM; + + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_on_f0(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_update_gamma(ctx, brightness)); + s6e3ha2_call_write_func(ret, s6e3ha2_aor_control(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_set_vint(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_off_f0(ctx)); + + return 0; +} + +static const struct backlight_ops s6e3ha2_bl_ops = { + .get_brightness = s6e3ha2_get_brightness, + .update_status = s6e3ha2_set_brightness, +}; + +static int s6e3ha2_panel_init(struct s6e3ha2 *ctx) +{ + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); + int ret; + + s6e3ha2_call_write_func(ret, mipi_dsi_dcs_exit_sleep_mode(dsi)); + usleep_range(5000, 6000); + + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_on_f0(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_single_dsi_set(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_on_fc(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_freq_calibration(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_off_fc(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_off_f0(ctx)); + + return 0; +} + +static int s6e3ha2_power_off(struct s6e3ha2 *ctx) +{ + return regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies); +} + +static int s6e3ha2_disable(struct drm_panel *panel) +{ + struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel); + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); + int ret; + + s6e3ha2_call_write_func(ret, mipi_dsi_dcs_enter_sleep_mode(dsi)); + s6e3ha2_call_write_func(ret, mipi_dsi_dcs_set_display_off(dsi)); + + msleep(40); + ctx->bl_dev->props.power = FB_BLANK_NORMAL; + + return 0; +} + +static int s6e3ha2_unprepare(struct drm_panel *panel) +{ + struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel); + + return s6e3ha2_power_off(ctx); +} + +static int s6e3ha2_power_on(struct s6e3ha2 *ctx) +{ + int ret; + + ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies); + if (ret < 0) + return ret; + + msleep(120); + + gpiod_set_value(ctx->enable_gpio, 0); + usleep_range(5000, 6000); + gpiod_set_value(ctx->enable_gpio, 1); + + gpiod_set_value(ctx->reset_gpio, 1); + usleep_range(5000, 6000); + gpiod_set_value(ctx->reset_gpio, 0); + usleep_range(5000, 6000); + + return 0; +} +static int s6e3ha2_prepare(struct drm_panel *panel) +{ + struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel); + int ret; + + ret = s6e3ha2_power_on(ctx); + if (ret < 0) + return ret; + + ret = s6e3ha2_panel_init(ctx); + if (ret < 0) + goto err; + + ctx->bl_dev->props.power = FB_BLANK_NORMAL; + + return 0; + +err: + s6e3ha2_power_off(ctx); + return ret; +} + +static int s6e3ha2_enable(struct drm_panel *panel) +{ + struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel); + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); + int ret; + + /* common setting */ + s6e3ha2_call_write_func(ret, + mipi_dsi_dcs_set_tear_on(dsi, MIPI_DSI_DCS_TEAR_MODE_VBLANK)); + + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_on_f0(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_on_fc(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_touch_hsync_on1(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_pentile_control(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_poc_global(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_poc_setting(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_off_fc(ctx)); + + /* pcd setting off for TB */ + s6e3ha2_call_write_func(ret, s6e3ha2_pcd_set_off(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_err_fg_set(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_te_start_setting(ctx)); + + /* brightness setting */ + s6e3ha2_call_write_func(ret, s6e3ha2_set_brightness(ctx->bl_dev)); + s6e3ha2_call_write_func(ret, s6e3ha2_aor_control(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_caps_elvss_set(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_gamma_update(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_acl_off(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_acl_off_opr(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_hbm_off(ctx)); + + /* elvss temp compensation */ + s6e3ha2_call_write_func(ret, s6e3ha2_test_global(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_off_f0(ctx)); + + s6e3ha2_call_write_func(ret, mipi_dsi_dcs_set_display_on(dsi)); + ctx->bl_dev->props.power = FB_BLANK_UNBLANK; + + return 0; +} + +static const struct drm_display_mode default_mode = { + .clock = 222372, + .hdisplay = 1440, + .hsync_start = 1440 + 1, + .hsync_end = 1440 + 1 + 1, + .htotal = 1440 + 1 + 1 + 1, + .vdisplay = 2560, + .vsync_start = 2560 + 1, + .vsync_end = 2560 + 1 + 1, + .vtotal = 2560 + 1 + 1 + 15, + .vrefresh = 60, + .flags = 0, +}; + +static int s6e3ha2_get_modes(struct drm_panel *panel) +{ + struct drm_connector *connector = panel->connector; + struct drm_display_mode *mode; + + mode = drm_mode_duplicate(panel->drm, &default_mode); + if (!mode) { + DRM_ERROR("failed to add mode %ux%ux@%u\n", + default_mode.hdisplay, default_mode.vdisplay, + default_mode.vrefresh); + return -ENOMEM; + } + + drm_mode_set_name(mode); + + mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED; + drm_mode_probed_add(connector, mode); + + connector->display_info.width_mm = 71; + connector->display_info.height_mm = 125; + + return 1; +} + +static const struct drm_panel_funcs s6e3ha2_drm_funcs = { + .disable = s6e3ha2_disable, + .unprepare = s6e3ha2_unprepare, + .prepare = s6e3ha2_prepare, + .enable = s6e3ha2_enable, + .get_modes = s6e3ha2_get_modes, +}; + +static int s6e3ha2_probe(struct mipi_dsi_device *dsi) +{ + struct device *dev = &dsi->dev; + struct s6e3ha2 *ctx; + int ret; + + ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL); + if (!ctx) + return -ENOMEM; + + mipi_dsi_set_drvdata(dsi, ctx); + + ctx->dev = dev; + + dsi->lanes = 4; + dsi->format = MIPI_DSI_FMT_RGB888; + dsi->mode_flags = MIPI_DSI_CLOCK_NON_CONTINUOUS; + + ctx->supplies[0].supply = "vdd3"; + ctx->supplies[1].supply = "vci"; + + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ctx->supplies), + ctx->supplies); + if (ret < 0) { + dev_err(dev, "failed to get regulators: %d\n", ret); + return ret; + } + + ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW); + if (IS_ERR(ctx->reset_gpio)) { + dev_err(dev, "cannot get reset-gpios %ld\n", + PTR_ERR(ctx->reset_gpio)); + return PTR_ERR(ctx->reset_gpio); + } + + ctx->enable_gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_HIGH); + if (IS_ERR(ctx->enable_gpio)) { + dev_err(dev, "cannot get enable-gpios %ld\n", + PTR_ERR(ctx->enable_gpio)); + return PTR_ERR(ctx->enable_gpio); + } + + ctx->bl_dev = backlight_device_register("s6e3ha2", dev, ctx, + &s6e3ha2_bl_ops, NULL); + if (IS_ERR(ctx->bl_dev)) { + dev_err(dev, "failed to register backlight device\n"); + return PTR_ERR(ctx->bl_dev); + } + + ctx->bl_dev->props.max_brightness = S6E3HA2_MAX_BRIGHTNESS; + ctx->bl_dev->props.brightness = S6E3HA2_DEFAULT_BRIGHTNESS; + ctx->bl_dev->props.power = FB_BLANK_POWERDOWN; + + drm_panel_init(&ctx->panel); + ctx->panel.dev = dev; + ctx->panel.funcs = &s6e3ha2_drm_funcs; + + ret = drm_panel_add(&ctx->panel); + if (ret < 0) + goto unregister_backlight; + + ret = mipi_dsi_attach(dsi); + if (ret < 0) + goto remove_panel; + + return ret; + +remove_panel: + drm_panel_remove(&ctx->panel); + +unregister_backlight: + backlight_device_unregister(ctx->bl_dev); + + return ret; +} + +static int s6e3ha2_remove(struct mipi_dsi_device *dsi) +{ + struct s6e3ha2 *ctx = mipi_dsi_get_drvdata(dsi); + + mipi_dsi_detach(dsi); + drm_panel_remove(&ctx->panel); + backlight_device_unregister(ctx->bl_dev); + + return 0; +} + +static const struct of_device_id s6e3ha2_of_match[] = { + { .compatible = "samsung,s6e3ha2" }, + { } +}; +MODULE_DEVICE_TABLE(of, s6e3ha2_of_match); + +static struct mipi_dsi_driver s6e3ha2_driver = { + .probe = s6e3ha2_probe, + .remove = s6e3ha2_remove, + .driver = { + .name = "panel-samsung-s6e3ha2", + .of_match_table = s6e3ha2_of_match, + }, +}; +module_mipi_dsi_driver(s6e3ha2_driver); + +MODULE_AUTHOR("Donghwa Lee <dh09.lee@samsung.com>"); +MODULE_AUTHOR("Hyungwon Hwang <human.hwang@samsung.com>"); +MODULE_AUTHOR("Hoegeun Kwon <hoegeun.kwon@samsung.com>"); +MODULE_DESCRIPTION("MIPI-DSI based s6e3ha2 AMOLED Panel Driver"); +MODULE_LICENSE("GPL v2"); -- 1.9.1 ^ permalink raw reply related [flat|nested] 31+ messages in thread
* [PATCH v10 2/3] drm/panel: Add support for S6E3HA2 panel driver on TM2 board @ 2017-02-22 1:09 ` Hoegeun Kwon 0 siblings, 0 replies; 31+ messages in thread From: Hoegeun Kwon @ 2017-02-22 1:09 UTC (permalink / raw) To: thierry.reding, airlied, robh+dt, mark.rutland, catalin.marinas, will.deacon, kgene, krzk Cc: devicetree, linux-samsung-soc, cw00.choi, linux-kernel, dri-devel, javier, jh80.chung, andi.shyti, Hoegeun Kwon, linux-arm-kernel This patch add support for MIPI-DSI based S6E3HA2 AMOLED panel driver. This panel has 1440x2560 resolution in 5.7-inch physical panel in the TM2 device. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com> Tested-by: Chanwoo Choi <cw00.choi@samsung.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> --- drivers/gpu/drm/panel/Kconfig | 6 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c | 739 ++++++++++++++++++++++++++ 3 files changed, 746 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig index 62aba97..d913c83 100644 --- a/drivers/gpu/drm/panel/Kconfig +++ b/drivers/gpu/drm/panel/Kconfig @@ -52,6 +52,12 @@ config DRM_PANEL_PANASONIC_VVX10F034N00 WUXGA (1920x1200) Novatek NT1397-based DSI panel as found in some Xperia Z2 tablets +config DRM_PANEL_SAMSUNG_S6E3HA2 + tristate "Samsung S6E3HA2 DSI video mode panel" + depends on OF + depends on DRM_MIPI_DSI + select VIDEOMODE_HELPERS + config DRM_PANEL_SAMSUNG_S6E8AA0 tristate "Samsung S6E8AA0 DSI video mode panel" depends on OF diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile index a5c7ec0..1d483b0 100644 --- a/drivers/gpu/drm/panel/Makefile +++ b/drivers/gpu/drm/panel/Makefile @@ -3,6 +3,7 @@ obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o obj-$(CONFIG_DRM_PANEL_LG_LG4573) += panel-lg-lg4573.o obj-$(CONFIG_DRM_PANEL_PANASONIC_VVX10F034N00) += panel-panasonic-vvx10f034n00.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_LD9040) += panel-samsung-ld9040.o +obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E3HA2) += panel-samsung-s6e3ha2.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E8AA0) += panel-samsung-s6e8aa0.o obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o diff --git a/drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c b/drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c new file mode 100644 index 0000000..4cc08d7 --- /dev/null +++ b/drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c @@ -0,0 +1,739 @@ +/* + * MIPI-DSI based s6e3ha2 AMOLED 5.7 inch panel driver. + * + * Copyright (c) 2016 Samsung Electronics Co., Ltd. + * Donghwa Lee <dh09.lee@samsung.com> + * Hyungwon Hwang <human.hwang@samsung.com> + * Hoegeun Kwon <hoegeun.kwon@samsung.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <drm/drmP.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_panel.h> +#include <linux/backlight.h> +#include <linux/gpio/consumer.h> +#include <linux/regulator/consumer.h> + +#define S6E3HA2_MIN_BRIGHTNESS 0 +#define S6E3HA2_MAX_BRIGHTNESS 100 +#define S6E3HA2_DEFAULT_BRIGHTNESS 80 + +#define S6E3HA2_NUM_GAMMA_STEPS 46 +#define S6E3HA2_GAMMA_CMD_CNT 35 +#define S6E3HA2_VINT_STATUS_MAX 10 + +static const u8 gamma_tbl[S6E3HA2_NUM_GAMMA_STEPS][S6E3HA2_GAMMA_CMD_CNT] = { + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x82, 0x83, + 0x85, 0x88, 0x8b, 0x8b, 0x84, 0x88, 0x82, 0x82, 0x89, 0x86, 0x8c, + 0x94, 0x84, 0xb1, 0xaf, 0x8e, 0xcf, 0xad, 0xc9, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x84, 0x84, + 0x85, 0x87, 0x8b, 0x8a, 0x84, 0x88, 0x82, 0x82, 0x89, 0x86, 0x8a, + 0x93, 0x84, 0xb0, 0xae, 0x8e, 0xc9, 0xa8, 0xc5, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x8a, 0x8a, 0x84, 0x88, 0x81, 0x84, 0x8a, 0x88, 0x8a, + 0x91, 0x84, 0xb1, 0xae, 0x8b, 0xd5, 0xb2, 0xcc, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x8a, 0x8a, 0x84, 0x87, 0x81, 0x84, 0x8a, 0x87, 0x8a, + 0x91, 0x85, 0xae, 0xac, 0x8a, 0xc3, 0xa3, 0xc0, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x85, 0x85, + 0x86, 0x85, 0x88, 0x89, 0x84, 0x89, 0x82, 0x84, 0x87, 0x85, 0x8b, + 0x91, 0x88, 0xad, 0xab, 0x8a, 0xb7, 0x9b, 0xb6, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x89, 0x8a, 0x84, 0x89, 0x83, 0x83, 0x86, 0x84, 0x8b, + 0x90, 0x84, 0xb0, 0xae, 0x8b, 0xce, 0xad, 0xc8, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x87, 0x89, 0x8a, 0x83, 0x87, 0x82, 0x85, 0x88, 0x87, 0x89, + 0x8f, 0x84, 0xac, 0xaa, 0x89, 0xb1, 0x98, 0xaf, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x88, 0x89, 0x84, 0x88, 0x83, 0x82, 0x85, 0x84, 0x8c, + 0x91, 0x86, 0xac, 0xaa, 0x89, 0xc2, 0xa5, 0xbd, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x85, 0x87, 0x89, 0x8a, 0x83, 0x87, 0x82, 0x85, 0x88, 0x87, 0x88, + 0x8b, 0x82, 0xad, 0xaa, 0x8a, 0xc2, 0xa5, 0xbd, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x87, 0x89, 0x84, 0x88, 0x83, 0x82, 0x85, 0x84, 0x8a, + 0x8e, 0x84, 0xae, 0xac, 0x89, 0xda, 0xb7, 0xd0, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x85, 0x86, 0x87, 0x89, 0x84, 0x88, 0x83, 0x80, 0x83, 0x82, 0x8b, + 0x8e, 0x85, 0xac, 0xaa, 0x89, 0xc8, 0xaa, 0xc1, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x85, 0x86, 0x87, 0x89, 0x81, 0x85, 0x81, 0x84, 0x86, 0x84, 0x8c, + 0x8c, 0x84, 0xa9, 0xa8, 0x87, 0xa3, 0x92, 0xa1, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x85, 0x86, 0x87, 0x89, 0x84, 0x86, 0x83, 0x80, 0x83, 0x81, 0x8c, + 0x8d, 0x84, 0xaa, 0xaa, 0x89, 0xce, 0xaf, 0xc5, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x85, 0x86, 0x87, 0x89, 0x81, 0x83, 0x80, 0x83, 0x85, 0x85, 0x8c, + 0x8c, 0x84, 0xa8, 0xa8, 0x88, 0xb5, 0x9f, 0xb0, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x86, 0x86, 0x87, 0x88, 0x81, 0x83, 0x80, 0x83, 0x85, 0x85, 0x8c, + 0x8b, 0x84, 0xab, 0xa8, 0x86, 0xd4, 0xb4, 0xc9, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x86, 0x86, 0x87, 0x88, 0x81, 0x83, 0x80, 0x84, 0x84, 0x85, 0x8b, + 0x8a, 0x83, 0xa6, 0xa5, 0x84, 0xbb, 0xa4, 0xb3, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84, + 0x86, 0x85, 0x86, 0x86, 0x82, 0x85, 0x81, 0x82, 0x83, 0x84, 0x8e, + 0x8b, 0x83, 0xa4, 0xa3, 0x8a, 0xa1, 0x93, 0x9d, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x87, 0x87, 0x82, 0x85, 0x81, 0x82, 0x82, 0x84, 0x8e, + 0x8b, 0x83, 0xa4, 0xa2, 0x86, 0xc1, 0xa9, 0xb7, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x87, 0x87, 0x82, 0x85, 0x81, 0x82, 0x82, 0x84, 0x8d, + 0x89, 0x82, 0xa2, 0xa1, 0x84, 0xa7, 0x98, 0xa1, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x83, 0x83, + 0x85, 0x86, 0x87, 0x87, 0x82, 0x85, 0x81, 0x83, 0x83, 0x85, 0x8c, + 0x87, 0x7f, 0xa2, 0x9d, 0x88, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xbb, 0x00, 0xc5, 0x00, 0xb4, 0x87, 0x86, 0x86, 0x84, 0x83, + 0x86, 0x87, 0x87, 0x87, 0x80, 0x82, 0x7f, 0x86, 0x86, 0x88, 0x8a, + 0x84, 0x7e, 0x9d, 0x9c, 0x82, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xbd, 0x00, 0xc7, 0x00, 0xb7, 0x87, 0x85, 0x85, 0x84, 0x83, + 0x86, 0x86, 0x86, 0x88, 0x81, 0x83, 0x80, 0x83, 0x84, 0x85, 0x8a, + 0x85, 0x7e, 0x9c, 0x9b, 0x85, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xc0, 0x00, 0xca, 0x00, 0xbb, 0x87, 0x86, 0x85, 0x83, 0x83, + 0x85, 0x86, 0x86, 0x88, 0x81, 0x83, 0x80, 0x84, 0x85, 0x86, 0x89, + 0x83, 0x7d, 0x9c, 0x99, 0x87, 0x7b, 0x7b, 0x7c, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xc4, 0x00, 0xcd, 0x00, 0xbe, 0x87, 0x86, 0x85, 0x83, 0x83, + 0x86, 0x85, 0x85, 0x87, 0x81, 0x82, 0x80, 0x82, 0x82, 0x83, 0x8a, + 0x85, 0x7f, 0x9f, 0x9b, 0x86, 0xb4, 0xa1, 0xac, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xc7, 0x00, 0xd0, 0x00, 0xc2, 0x87, 0x85, 0x85, 0x83, 0x82, + 0x85, 0x85, 0x85, 0x86, 0x82, 0x83, 0x80, 0x82, 0x82, 0x84, 0x87, + 0x86, 0x80, 0x9e, 0x9a, 0x87, 0xa7, 0x98, 0xa1, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xca, 0x00, 0xd2, 0x00, 0xc5, 0x87, 0x85, 0x84, 0x82, 0x82, + 0x84, 0x85, 0x85, 0x86, 0x81, 0x82, 0x7f, 0x82, 0x82, 0x84, 0x88, + 0x86, 0x81, 0x9d, 0x98, 0x86, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xce, 0x00, 0xd6, 0x00, 0xca, 0x86, 0x85, 0x84, 0x83, 0x83, + 0x85, 0x84, 0x84, 0x85, 0x81, 0x82, 0x80, 0x81, 0x81, 0x82, 0x89, + 0x86, 0x81, 0x9c, 0x97, 0x86, 0xa7, 0x98, 0xa1, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xd1, 0x00, 0xd9, 0x00, 0xce, 0x86, 0x84, 0x83, 0x83, 0x82, + 0x85, 0x85, 0x85, 0x86, 0x81, 0x83, 0x81, 0x82, 0x82, 0x83, 0x86, + 0x83, 0x7f, 0x99, 0x95, 0x86, 0xbb, 0xa4, 0xb3, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xd4, 0x00, 0xdb, 0x00, 0xd1, 0x86, 0x85, 0x83, 0x83, 0x82, + 0x85, 0x84, 0x84, 0x85, 0x80, 0x83, 0x82, 0x80, 0x80, 0x81, 0x87, + 0x84, 0x81, 0x98, 0x93, 0x85, 0xae, 0x9c, 0xa8, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xd8, 0x00, 0xde, 0x00, 0xd6, 0x86, 0x84, 0x83, 0x81, 0x81, + 0x83, 0x85, 0x85, 0x85, 0x82, 0x83, 0x81, 0x81, 0x81, 0x83, 0x86, + 0x84, 0x80, 0x98, 0x91, 0x85, 0x7b, 0x7b, 0x7c, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xdc, 0x00, 0xe2, 0x00, 0xda, 0x85, 0x84, 0x83, 0x82, 0x82, + 0x84, 0x84, 0x84, 0x85, 0x81, 0x82, 0x82, 0x80, 0x80, 0x81, 0x83, + 0x82, 0x7f, 0x99, 0x93, 0x86, 0x94, 0x8b, 0x92, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xdf, 0x00, 0xe5, 0x00, 0xde, 0x85, 0x84, 0x82, 0x82, 0x82, + 0x84, 0x83, 0x83, 0x84, 0x81, 0x81, 0x80, 0x83, 0x82, 0x84, 0x82, + 0x81, 0x7f, 0x99, 0x92, 0x86, 0x7b, 0x7b, 0x7c, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x83, 0x83, 0x84, 0x80, 0x81, 0x80, 0x83, 0x83, 0x84, 0x80, + 0x81, 0x7c, 0x99, 0x92, 0x87, 0xa1, 0x93, 0x9d, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x85, 0x84, 0x83, 0x81, 0x81, + 0x82, 0x82, 0x82, 0x83, 0x80, 0x81, 0x80, 0x81, 0x80, 0x82, 0x83, + 0x82, 0x80, 0x91, 0x8d, 0x83, 0x9a, 0x90, 0x96, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x83, 0x83, 0x84, 0x80, 0x81, 0x80, 0x81, 0x80, 0x82, 0x83, + 0x81, 0x7f, 0x91, 0x8c, 0x82, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x83, 0x83, 0x83, 0x82, 0x82, 0x81, 0x81, 0x80, 0x82, 0x82, + 0x82, 0x7f, 0x94, 0x89, 0x84, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x83, 0x83, 0x83, 0x82, 0x82, 0x81, 0x81, 0x80, 0x82, 0x83, + 0x82, 0x7f, 0x91, 0x85, 0x81, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x83, 0x83, 0x83, 0x80, 0x80, 0x7f, 0x83, 0x82, 0x84, 0x83, + 0x82, 0x7f, 0x90, 0x84, 0x81, 0x9a, 0x90, 0x96, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x80, 0x80, + 0x82, 0x83, 0x83, 0x83, 0x80, 0x80, 0x7f, 0x80, 0x80, 0x81, 0x81, + 0x82, 0x83, 0x7e, 0x80, 0x7c, 0xa4, 0x97, 0x9f, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xe9, 0x00, 0xec, 0x00, 0xe8, 0x84, 0x83, 0x82, 0x81, 0x81, + 0x82, 0x82, 0x82, 0x83, 0x7f, 0x7f, 0x7f, 0x81, 0x80, 0x82, 0x83, + 0x83, 0x84, 0x79, 0x7c, 0x79, 0xb1, 0xa0, 0xaa, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xed, 0x00, 0xf0, 0x00, 0xec, 0x83, 0x83, 0x82, 0x80, 0x80, + 0x81, 0x82, 0x82, 0x82, 0x7f, 0x7f, 0x7e, 0x81, 0x81, 0x82, 0x80, + 0x81, 0x81, 0x84, 0x84, 0x83, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xf1, 0x00, 0xf4, 0x00, 0xf1, 0x83, 0x82, 0x82, 0x80, 0x80, + 0x81, 0x82, 0x82, 0x82, 0x80, 0x80, 0x80, 0x80, 0x80, 0x81, 0x7d, + 0x7e, 0x7f, 0x84, 0x84, 0x83, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xf6, 0x00, 0xf7, 0x00, 0xf5, 0x82, 0x82, 0x81, 0x80, 0x80, + 0x80, 0x82, 0x82, 0x82, 0x80, 0x80, 0x80, 0x7f, 0x7f, 0x7f, 0x82, + 0x82, 0x82, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x00, 0xfa, 0x00, 0xfb, 0x00, 0xfa, 0x81, 0x81, 0x81, 0x80, 0x80, + 0x80, 0x82, 0x82, 0x82, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x01, 0x00, 0x01, 0x00, 0x01, 0x00, 0x80, 0x80, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 }, + { 0x01, 0x00, 0x01, 0x00, 0x01, 0x00, 0x80, 0x80, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, + 0x00, 0x00 } +}; + +unsigned char vint_table[S6E3HA2_VINT_STATUS_MAX] = { + 0x18, 0x19, 0x1a, 0x1b, 0x1c, + 0x1d, 0x1e, 0x1f, 0x20, 0x21 +}; + +struct s6e3ha2 { + struct device *dev; + struct drm_panel panel; + struct backlight_device *bl_dev; + + struct regulator_bulk_data supplies[2]; + struct gpio_desc *reset_gpio; + struct gpio_desc *enable_gpio; +}; + +static int s6e3ha2_dcs_write(struct s6e3ha2 *ctx, const void *data, size_t len) +{ + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); + + return mipi_dsi_dcs_write_buffer(dsi, data, len); +} + +#define s6e3ha2_dcs_write_seq_static(ctx, seq...) do { \ + static const u8 d[] = { seq }; \ + int ret; \ + ret = s6e3ha2_dcs_write(ctx, d, ARRAY_SIZE(d)); \ + if (ret < 0) \ + return ret; \ +} while (0) + +#define s6e3ha2_call_write_func(ret, func) do { \ + ret = (func); \ + if (ret < 0) \ + return ret; \ +} while (0) + +static int s6e3ha2_test_key_on_f0(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xf0, 0x5a, 0x5a); + return 0; +} + +static int s6e3ha2_test_key_off_f0(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xf0, 0xa5, 0xa5); + return 0; +} + +static int s6e3ha2_test_key_on_fc(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xfc, 0x5a, 0x5a); + return 0; +} + +static int s6e3ha2_test_key_off_fc(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xfc, 0xa5, 0xa5); + return 0; +} + +static int s6e3ha2_single_dsi_set(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xf2, 0x67); + s6e3ha2_dcs_write_seq_static(ctx, 0xf9, 0x09); + return 0; +} + +static int s6e3ha2_freq_calibration(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xfd, 0x1c); + s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0x20, 0x39); + s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0xa0); + s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0x20); + s6e3ha2_dcs_write_seq_static(ctx, 0xce, 0x03, 0x3b, 0x12, 0x62, 0x40, + 0x80, 0xc0, 0x28, 0x28, 0x28, 0x28, 0x39, 0xc5); + return 0; +} + +static int s6e3ha2_aor_control(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb2, 0x03, 0x10); + return 0; +} + +static int s6e3ha2_caps_elvss_set(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb6, 0x9c, 0x0a); + return 0; +} + +static int s6e3ha2_acl_off(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0x55, 0x00); + return 0; +} + +static int s6e3ha2_acl_off_opr(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb5, 0x40); + return 0; +} + +static int s6e3ha2_test_global(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb0, 0x07); + return 0; +} + +static int s6e3ha2_test(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb8, 0x19); + return 0; +} + +static int s6e3ha2_touch_hsync_on1(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xbd, 0x33, 0x11, 0x02, + 0x16, 0x02, 0x16); + return 0; +} + +static int s6e3ha2_pentile_control(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xc0, 0x00, 0x00, 0xd8, 0xd8); + return 0; +} + +static int s6e3ha2_poc_global(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb0, 0x20); + return 0; +} + +static int s6e3ha2_poc_setting(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0x08); + return 0; +} + +static int s6e3ha2_pcd_set_off(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xcc, 0x40, 0x51); + return 0; +} + +static int s6e3ha2_err_fg_set(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xed, 0x44); + return 0; +} + +static int s6e3ha2_hbm_off(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0x53, 0x00); + return 0; +} + +static int s6e3ha2_te_start_setting(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xb9, 0x10, 0x09, 0xff, 0x00, 0x09); + return 0; +} + +static int s6e3ha2_gamma_update(struct s6e3ha2 *ctx) +{ + s6e3ha2_dcs_write_seq_static(ctx, 0xf7, 0x03); + ndelay(100); /* need for 100ns delay */ + s6e3ha2_dcs_write_seq_static(ctx, 0xf7, 0x00); + return 0; +} + +static int s6e3ha2_get_brightness(struct backlight_device *bl_dev) +{ + return bl_dev->props.brightness; +} + +static int s6e3ha2_set_vint(struct s6e3ha2 *ctx) +{ + struct backlight_device *bl_dev = ctx->bl_dev; + unsigned int brightness = bl_dev->props.brightness; + unsigned char data[] = { 0xf4, 0x8b, + vint_table[brightness * (S6E3HA2_VINT_STATUS_MAX - 1) / + S6E3HA2_MAX_BRIGHTNESS] }; + + return s6e3ha2_dcs_write(ctx, data, ARRAY_SIZE(data)); +} + +static unsigned int s6e3ha2_get_brightness_index(unsigned int brightness) +{ + return (brightness * (S6E3HA2_NUM_GAMMA_STEPS - 1)) / + S6E3HA2_MAX_BRIGHTNESS; +} + +static int s6e3ha2_update_gamma(struct s6e3ha2 *ctx, unsigned int brightness) +{ + struct backlight_device *bl_dev = ctx->bl_dev; + unsigned int index = s6e3ha2_get_brightness_index(brightness); + u8 data[S6E3HA2_GAMMA_CMD_CNT + 1] = { 0xca, }; + int ret; + + memcpy(data + 1, gamma_tbl + index, S6E3HA2_GAMMA_CMD_CNT); + s6e3ha2_call_write_func(ret, + s6e3ha2_dcs_write(ctx, data, ARRAY_SIZE(data))); + + s6e3ha2_call_write_func(ret, s6e3ha2_gamma_update(ctx)); + bl_dev->props.brightness = brightness; + + return 0; +} + +static int s6e3ha2_set_brightness(struct backlight_device *bl_dev) +{ + struct s6e3ha2 *ctx = bl_get_data(bl_dev); + unsigned int brightness = bl_dev->props.brightness; + int ret; + + if (brightness < S6E3HA2_MIN_BRIGHTNESS || + brightness > bl_dev->props.max_brightness) { + dev_err(ctx->dev, "Invalid brightness: %u\n", brightness); + return -EINVAL; + } + + if (bl_dev->props.power > FB_BLANK_NORMAL) + return -EPERM; + + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_on_f0(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_update_gamma(ctx, brightness)); + s6e3ha2_call_write_func(ret, s6e3ha2_aor_control(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_set_vint(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_off_f0(ctx)); + + return 0; +} + +static const struct backlight_ops s6e3ha2_bl_ops = { + .get_brightness = s6e3ha2_get_brightness, + .update_status = s6e3ha2_set_brightness, +}; + +static int s6e3ha2_panel_init(struct s6e3ha2 *ctx) +{ + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); + int ret; + + s6e3ha2_call_write_func(ret, mipi_dsi_dcs_exit_sleep_mode(dsi)); + usleep_range(5000, 6000); + + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_on_f0(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_single_dsi_set(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_on_fc(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_freq_calibration(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_off_fc(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_off_f0(ctx)); + + return 0; +} + +static int s6e3ha2_power_off(struct s6e3ha2 *ctx) +{ + return regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies); +} + +static int s6e3ha2_disable(struct drm_panel *panel) +{ + struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel); + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); + int ret; + + s6e3ha2_call_write_func(ret, mipi_dsi_dcs_enter_sleep_mode(dsi)); + s6e3ha2_call_write_func(ret, mipi_dsi_dcs_set_display_off(dsi)); + + msleep(40); + ctx->bl_dev->props.power = FB_BLANK_NORMAL; + + return 0; +} + +static int s6e3ha2_unprepare(struct drm_panel *panel) +{ + struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel); + + return s6e3ha2_power_off(ctx); +} + +static int s6e3ha2_power_on(struct s6e3ha2 *ctx) +{ + int ret; + + ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies); + if (ret < 0) + return ret; + + msleep(120); + + gpiod_set_value(ctx->enable_gpio, 0); + usleep_range(5000, 6000); + gpiod_set_value(ctx->enable_gpio, 1); + + gpiod_set_value(ctx->reset_gpio, 1); + usleep_range(5000, 6000); + gpiod_set_value(ctx->reset_gpio, 0); + usleep_range(5000, 6000); + + return 0; +} +static int s6e3ha2_prepare(struct drm_panel *panel) +{ + struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel); + int ret; + + ret = s6e3ha2_power_on(ctx); + if (ret < 0) + return ret; + + ret = s6e3ha2_panel_init(ctx); + if (ret < 0) + goto err; + + ctx->bl_dev->props.power = FB_BLANK_NORMAL; + + return 0; + +err: + s6e3ha2_power_off(ctx); + return ret; +} + +static int s6e3ha2_enable(struct drm_panel *panel) +{ + struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel); + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); + int ret; + + /* common setting */ + s6e3ha2_call_write_func(ret, + mipi_dsi_dcs_set_tear_on(dsi, MIPI_DSI_DCS_TEAR_MODE_VBLANK)); + + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_on_f0(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_on_fc(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_touch_hsync_on1(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_pentile_control(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_poc_global(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_poc_setting(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_off_fc(ctx)); + + /* pcd setting off for TB */ + s6e3ha2_call_write_func(ret, s6e3ha2_pcd_set_off(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_err_fg_set(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_te_start_setting(ctx)); + + /* brightness setting */ + s6e3ha2_call_write_func(ret, s6e3ha2_set_brightness(ctx->bl_dev)); + s6e3ha2_call_write_func(ret, s6e3ha2_aor_control(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_caps_elvss_set(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_gamma_update(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_acl_off(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_acl_off_opr(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_hbm_off(ctx)); + + /* elvss temp compensation */ + s6e3ha2_call_write_func(ret, s6e3ha2_test_global(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test(ctx)); + s6e3ha2_call_write_func(ret, s6e3ha2_test_key_off_f0(ctx)); + + s6e3ha2_call_write_func(ret, mipi_dsi_dcs_set_display_on(dsi)); + ctx->bl_dev->props.power = FB_BLANK_UNBLANK; + + return 0; +} + +static const struct drm_display_mode default_mode = { + .clock = 222372, + .hdisplay = 1440, + .hsync_start = 1440 + 1, + .hsync_end = 1440 + 1 + 1, + .htotal = 1440 + 1 + 1 + 1, + .vdisplay = 2560, + .vsync_start = 2560 + 1, + .vsync_end = 2560 + 1 + 1, + .vtotal = 2560 + 1 + 1 + 15, + .vrefresh = 60, + .flags = 0, +}; + +static int s6e3ha2_get_modes(struct drm_panel *panel) +{ + struct drm_connector *connector = panel->connector; + struct drm_display_mode *mode; + + mode = drm_mode_duplicate(panel->drm, &default_mode); + if (!mode) { + DRM_ERROR("failed to add mode %ux%ux@%u\n", + default_mode.hdisplay, default_mode.vdisplay, + default_mode.vrefresh); + return -ENOMEM; + } + + drm_mode_set_name(mode); + + mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED; + drm_mode_probed_add(connector, mode); + + connector->display_info.width_mm = 71; + connector->display_info.height_mm = 125; + + return 1; +} + +static const struct drm_panel_funcs s6e3ha2_drm_funcs = { + .disable = s6e3ha2_disable, + .unprepare = s6e3ha2_unprepare, + .prepare = s6e3ha2_prepare, + .enable = s6e3ha2_enable, + .get_modes = s6e3ha2_get_modes, +}; + +static int s6e3ha2_probe(struct mipi_dsi_device *dsi) +{ + struct device *dev = &dsi->dev; + struct s6e3ha2 *ctx; + int ret; + + ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL); + if (!ctx) + return -ENOMEM; + + mipi_dsi_set_drvdata(dsi, ctx); + + ctx->dev = dev; + + dsi->lanes = 4; + dsi->format = MIPI_DSI_FMT_RGB888; + dsi->mode_flags = MIPI_DSI_CLOCK_NON_CONTINUOUS; + + ctx->supplies[0].supply = "vdd3"; + ctx->supplies[1].supply = "vci"; + + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ctx->supplies), + ctx->supplies); + if (ret < 0) { + dev_err(dev, "failed to get regulators: %d\n", ret); + return ret; + } + + ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW); + if (IS_ERR(ctx->reset_gpio)) { + dev_err(dev, "cannot get reset-gpios %ld\n", + PTR_ERR(ctx->reset_gpio)); + return PTR_ERR(ctx->reset_gpio); + } + + ctx->enable_gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_HIGH); + if (IS_ERR(ctx->enable_gpio)) { + dev_err(dev, "cannot get enable-gpios %ld\n", + PTR_ERR(ctx->enable_gpio)); + return PTR_ERR(ctx->enable_gpio); + } + + ctx->bl_dev = backlight_device_register("s6e3ha2", dev, ctx, + &s6e3ha2_bl_ops, NULL); + if (IS_ERR(ctx->bl_dev)) { + dev_err(dev, "failed to register backlight device\n"); + return PTR_ERR(ctx->bl_dev); + } + + ctx->bl_dev->props.max_brightness = S6E3HA2_MAX_BRIGHTNESS; + ctx->bl_dev->props.brightness = S6E3HA2_DEFAULT_BRIGHTNESS; + ctx->bl_dev->props.power = FB_BLANK_POWERDOWN; + + drm_panel_init(&ctx->panel); + ctx->panel.dev = dev; + ctx->panel.funcs = &s6e3ha2_drm_funcs; + + ret = drm_panel_add(&ctx->panel); + if (ret < 0) + goto unregister_backlight; + + ret = mipi_dsi_attach(dsi); + if (ret < 0) + goto remove_panel; + + return ret; + +remove_panel: + drm_panel_remove(&ctx->panel); + +unregister_backlight: + backlight_device_unregister(ctx->bl_dev); + + return ret; +} + +static int s6e3ha2_remove(struct mipi_dsi_device *dsi) +{ + struct s6e3ha2 *ctx = mipi_dsi_get_drvdata(dsi); + + mipi_dsi_detach(dsi); + drm_panel_remove(&ctx->panel); + backlight_device_unregister(ctx->bl_dev); + + return 0; +} + +static const struct of_device_id s6e3ha2_of_match[] = { + { .compatible = "samsung,s6e3ha2" }, + { } +}; +MODULE_DEVICE_TABLE(of, s6e3ha2_of_match); + +static struct mipi_dsi_driver s6e3ha2_driver = { + .probe = s6e3ha2_probe, + .remove = s6e3ha2_remove, + .driver = { + .name = "panel-samsung-s6e3ha2", + .of_match_table = s6e3ha2_of_match, + }, +}; +module_mipi_dsi_driver(s6e3ha2_driver); + +MODULE_AUTHOR("Donghwa Lee <dh09.lee@samsung.com>"); +MODULE_AUTHOR("Hyungwon Hwang <human.hwang@samsung.com>"); +MODULE_AUTHOR("Hoegeun Kwon <hoegeun.kwon@samsung.com>"); +MODULE_DESCRIPTION("MIPI-DSI based s6e3ha2 AMOLED Panel Driver"); +MODULE_LICENSE("GPL v2"); -- 1.9.1 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply related [flat|nested] 31+ messages in thread
* [PATCH v10 0/3] Add support for the S6E3HA2 panel on TM2 board [not found] <CGME20170220071000epcas1p38e002e5064bdf4c3b1b4886207dcaaf4@epcas1p3.samsung.com> 2017-02-20 7:09 ` Hoegeun Kwon @ 2017-02-22 1:09 ` Hoegeun Kwon 1 sibling, 0 replies; 31+ messages in thread From: Hoegeun Kwon @ 2017-02-22 1:09 UTC (permalink / raw) To: thierry.reding, airlied, robh+dt, mark.rutland, catalin.marinas, will.deacon, kgene, krzk Cc: dri-devel, devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel, javier, inki.dae, a.hajda, cw00.choi, jh80.chung, Andi Shyti, Hoegeun Kwon Dear Thierry, I understand that your opinion is: It is better to handle the error every time it is input to the register, rather than error handling at once in the struct using error. This not only makes the code easier to maintain, but also reduces unnecessary computation. So I modified the panel driver to code-by-code error handling. If this is not your opinion, could you tell me what your opinion? Best Regards, Hoegeun Changes for V10: - Fixed code-by-code error handling. Changes for V9: - Fixed the te-gpio to optional in bindings Changes for V8: - Applied below two patches: (drm/exynos) : drm/exynos: mic: Add mode_set callback function : drm/exynos: mic: Fix parse_dt function - The dt-binding patch and driver patch were divided. - Rebase these patches on samsung SoC tree[1] and tm2 touckey patch[2]. Change for V7: - Fixed the mode_set callback function of mic device driver. because the mic register is initialized when entering suspend mode, so should set the reg value whenever pre_enable is called. Changes for V6: - Fixed the parse_dt function of dsi device driver. - Removed OF graph of panel in DT and DT binding document. - Fixed the s6e3ha2 panel device driver. - Fixed from number size to ARRAY_SIZE(). - Fixed error handling in mipi_dsi_dcs_* functions. - Fixed the clock of display_mode. - Removed unnecessary casting and error log. Change for V5: - The V5 has only one fix in V4 below. - Removed the enable check of the mic driver in mode_set callback, because mode_set should be performed every time. Changes for V4: - Removed display-timings in devicetree, the display-timings has been fixed to be provided by the device driver. - Added the mode_set callback function into exynos_drm_mic, because the exynos_drm_mic driver can not parse a videomode struct by removing the display-timings from the devicetree. Changes for V3: - In the DT binding document, made it clearly that the panel is a child node of dsi. - Fix reset-gpio active from high to low. - Is the OF graph saying related to patch2? Althogh the panel is a child of dsi, I think OF graph necessary. because if a remote-endpoint is not specified, the dsi also panel is not probed. - The display-timings has been fixed to be provided by the device driver. however, I think display-timings is necessary in dts. because if dts does not have display-timings, dsi will not load. Changes for V2: - Fixed the samsung,s6e3ha2.txt DT document. - Added active high or low after the description of the GPIOs. - Removed the reg and added a description of the virtual channel number of a DSI peripheral. Depends on: [1] https://git.kernel.org/cgit/linux/kernel/git/krzk/linux.git/ (for-next branch) [2] https://patchwork.kernel.org/patch/9504131/ - ("arm64: dts: exynos: Add tm2 touchkey node") Hoegeun Kwon (2): dt-bindings: Add support for samsung s6e3ha2 panel binding drm/panel: Add support for S6E3HA2 panel driver on TM2 board Hyungwon Hwang (1): arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board .../bindings/display/panel/samsung,s6e3ha2.txt | 28 + arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 12 + drivers/gpu/drm/panel/Kconfig | 6 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c | 739 +++++++++++++++++++++ 5 files changed, 786 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c -- 1.9.1 ^ permalink raw reply [flat|nested] 31+ messages in thread
* [PATCH v10 0/3] Add support for the S6E3HA2 panel on TM2 board @ 2017-02-22 1:09 ` Hoegeun Kwon 0 siblings, 0 replies; 31+ messages in thread From: Hoegeun Kwon @ 2017-02-22 1:09 UTC (permalink / raw) To: linux-arm-kernel Dear Thierry, I understand that your opinion is: It is better to handle the error every time it is input to the register, rather than error handling at once in the struct using error. This not only makes the code easier to maintain, but also reduces unnecessary computation. So I modified the panel driver to code-by-code error handling. If this is not your opinion, could you tell me what your opinion? Best Regards, Hoegeun Changes for V10: - Fixed code-by-code error handling. Changes for V9: - Fixed the te-gpio to optional in bindings Changes for V8: - Applied below two patches: (drm/exynos) : drm/exynos: mic: Add mode_set callback function : drm/exynos: mic: Fix parse_dt function - The dt-binding patch and driver patch were divided. - Rebase these patches on samsung SoC tree[1] and tm2 touckey patch[2]. Change for V7: - Fixed the mode_set callback function of mic device driver. because the mic register is initialized when entering suspend mode, so should set the reg value whenever pre_enable is called. Changes for V6: - Fixed the parse_dt function of dsi device driver. - Removed OF graph of panel in DT and DT binding document. - Fixed the s6e3ha2 panel device driver. - Fixed from number size to ARRAY_SIZE(). - Fixed error handling in mipi_dsi_dcs_* functions. - Fixed the clock of display_mode. - Removed unnecessary casting and error log. Change for V5: - The V5 has only one fix in V4 below. - Removed the enable check of the mic driver in mode_set callback, because mode_set should be performed every time. Changes for V4: - Removed display-timings in devicetree, the display-timings has been fixed to be provided by the device driver. - Added the mode_set callback function into exynos_drm_mic, because the exynos_drm_mic driver can not parse a videomode struct by removing the display-timings from the devicetree. Changes for V3: - In the DT binding document, made it clearly that the panel is a child node of dsi. - Fix reset-gpio active from high to low. - Is the OF graph saying related to patch2? Althogh the panel is a child of dsi, I think OF graph necessary. because if a remote-endpoint is not specified, the dsi also panel is not probed. - The display-timings has been fixed to be provided by the device driver. however, I think display-timings is necessary in dts. because if dts does not have display-timings, dsi will not load. Changes for V2: - Fixed the samsung,s6e3ha2.txt DT document. - Added active high or low after the description of the GPIOs. - Removed the reg and added a description of the virtual channel number of a DSI peripheral. Depends on: [1] https://git.kernel.org/cgit/linux/kernel/git/krzk/linux.git/ (for-next branch) [2] https://patchwork.kernel.org/patch/9504131/ - ("arm64: dts: exynos: Add tm2 touchkey node") Hoegeun Kwon (2): dt-bindings: Add support for samsung s6e3ha2 panel binding drm/panel: Add support for S6E3HA2 panel driver on TM2 board Hyungwon Hwang (1): arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board .../bindings/display/panel/samsung,s6e3ha2.txt | 28 + arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 12 + drivers/gpu/drm/panel/Kconfig | 6 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c | 739 +++++++++++++++++++++ 5 files changed, 786 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c -- 1.9.1 ^ permalink raw reply [flat|nested] 31+ messages in thread
* [PATCH v10 0/3] Add support for the S6E3HA2 panel on TM2 board @ 2017-02-22 1:09 ` Hoegeun Kwon 0 siblings, 0 replies; 31+ messages in thread From: Hoegeun Kwon @ 2017-02-22 1:09 UTC (permalink / raw) To: thierry.reding, airlied, robh+dt, mark.rutland, catalin.marinas, will.deacon, kgene, krzk Cc: devicetree, linux-samsung-soc, cw00.choi, linux-kernel, dri-devel, javier, jh80.chung, Andi Shyti, Hoegeun Kwon, linux-arm-kernel Dear Thierry, I understand that your opinion is: It is better to handle the error every time it is input to the register, rather than error handling at once in the struct using error. This not only makes the code easier to maintain, but also reduces unnecessary computation. So I modified the panel driver to code-by-code error handling. If this is not your opinion, could you tell me what your opinion? Best Regards, Hoegeun Changes for V10: - Fixed code-by-code error handling. Changes for V9: - Fixed the te-gpio to optional in bindings Changes for V8: - Applied below two patches: (drm/exynos) : drm/exynos: mic: Add mode_set callback function : drm/exynos: mic: Fix parse_dt function - The dt-binding patch and driver patch were divided. - Rebase these patches on samsung SoC tree[1] and tm2 touckey patch[2]. Change for V7: - Fixed the mode_set callback function of mic device driver. because the mic register is initialized when entering suspend mode, so should set the reg value whenever pre_enable is called. Changes for V6: - Fixed the parse_dt function of dsi device driver. - Removed OF graph of panel in DT and DT binding document. - Fixed the s6e3ha2 panel device driver. - Fixed from number size to ARRAY_SIZE(). - Fixed error handling in mipi_dsi_dcs_* functions. - Fixed the clock of display_mode. - Removed unnecessary casting and error log. Change for V5: - The V5 has only one fix in V4 below. - Removed the enable check of the mic driver in mode_set callback, because mode_set should be performed every time. Changes for V4: - Removed display-timings in devicetree, the display-timings has been fixed to be provided by the device driver. - Added the mode_set callback function into exynos_drm_mic, because the exynos_drm_mic driver can not parse a videomode struct by removing the display-timings from the devicetree. Changes for V3: - In the DT binding document, made it clearly that the panel is a child node of dsi. - Fix reset-gpio active from high to low. - Is the OF graph saying related to patch2? Althogh the panel is a child of dsi, I think OF graph necessary. because if a remote-endpoint is not specified, the dsi also panel is not probed. - The display-timings has been fixed to be provided by the device driver. however, I think display-timings is necessary in dts. because if dts does not have display-timings, dsi will not load. Changes for V2: - Fixed the samsung,s6e3ha2.txt DT document. - Added active high or low after the description of the GPIOs. - Removed the reg and added a description of the virtual channel number of a DSI peripheral. Depends on: [1] https://git.kernel.org/cgit/linux/kernel/git/krzk/linux.git/ (for-next branch) [2] https://patchwork.kernel.org/patch/9504131/ - ("arm64: dts: exynos: Add tm2 touchkey node") Hoegeun Kwon (2): dt-bindings: Add support for samsung s6e3ha2 panel binding drm/panel: Add support for S6E3HA2 panel driver on TM2 board Hyungwon Hwang (1): arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board .../bindings/display/panel/samsung,s6e3ha2.txt | 28 + arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 12 + drivers/gpu/drm/panel/Kconfig | 6 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c | 739 +++++++++++++++++++++ 5 files changed, 786 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c -- 1.9.1 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: [PATCH v10 0/3] Add support for the S6E3HA2 panel on TM2 board @ 2017-02-22 1:40 ` Hoegeun Kwon 0 siblings, 0 replies; 31+ messages in thread From: Hoegeun Kwon @ 2017-02-22 1:40 UTC (permalink / raw) To: thierry.reding, airlied, robh+dt, mark.rutland, catalin.marinas, will.deacon, kgene, krzk Cc: dri-devel, devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel, javier, inki.dae, a.hajda, cw00.choi, jh80.chung, Andi Shyti, Hoegeun Kwon Hi all, This patchset is resent patchset. Because I have a missing TO, CC, I sent it again. Sorry, I will send it in the correct format next time. Best Regards, Hoegeun On 02/22/2017 10:09 AM, Hoegeun Kwon wrote: > Dear Thierry, > > I understand that your opinion is: > It is better to handle the error every time it is input to the > register, rather than error handling at once in the struct using > error. This not only makes the code easier to maintain, but also > reduces unnecessary computation. > > So I modified the panel driver to code-by-code error handling. > If this is not your opinion, could you tell me what your opinion? > > Best Regards, > Hoegeun > > > Changes for V10: > - Fixed code-by-code error handling. > > Changes for V9: > - Fixed the te-gpio to optional in bindings > > Changes for V8: > - Applied below two patches: (drm/exynos) > : drm/exynos: mic: Add mode_set callback function > : drm/exynos: mic: Fix parse_dt function > - The dt-binding patch and driver patch were divided. > - Rebase these patches on samsung SoC tree[1] and tm2 touckey patch[2]. > > Change for V7: > - Fixed the mode_set callback function of mic device driver. > because the mic register is initialized when entering suspend > mode, so should set the reg value whenever pre_enable is > called. > > Changes for V6: > - Fixed the parse_dt function of dsi device driver. > - Removed OF graph of panel in DT and DT binding document. > - Fixed the s6e3ha2 panel device driver. > - Fixed from number size to ARRAY_SIZE(). > - Fixed error handling in mipi_dsi_dcs_* functions. > - Fixed the clock of display_mode. > - Removed unnecessary casting and error log. > > Change for V5: > - The V5 has only one fix in V4 below. > - Removed the enable check of the mic driver in mode_set > callback, because mode_set should be performed every time. > > Changes for V4: > - Removed display-timings in devicetree, the display-timings has > been fixed to be provided by the device driver. > - Added the mode_set callback function into exynos_drm_mic, > because the exynos_drm_mic driver can not parse a videomode > struct by removing the display-timings from the devicetree. > > Changes for V3: > - In the DT binding document, made it clearly that the panel is a > child node of dsi. > - Fix reset-gpio active from high to low. > - Is the OF graph saying related to patch2? > Althogh the panel is a child of dsi, I think OF graph necessary. > because if a remote-endpoint is not specified, the dsi also > panel is not probed. > - The display-timings has been fixed to be provided by the device > driver. however, I think display-timings is necessary in dts. > because if dts does not have display-timings, dsi will not load. > > Changes for V2: > - Fixed the samsung,s6e3ha2.txt DT document. > - Added active high or low after the description of the GPIOs. > - Removed the reg and added a description of the virtual > channel number of a DSI peripheral. > > Depends on: > [1] https://git.kernel.org/cgit/linux/kernel/git/krzk/linux.git/ > (for-next branch) > [2] https://patchwork.kernel.org/patch/9504131/ > - ("arm64: dts: exynos: Add tm2 touchkey node") > > Hoegeun Kwon (2): > dt-bindings: Add support for samsung s6e3ha2 panel binding > drm/panel: Add support for S6E3HA2 panel driver on TM2 board > > Hyungwon Hwang (1): > arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board > > .../bindings/display/panel/samsung,s6e3ha2.txt | 28 + > arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 12 + > drivers/gpu/drm/panel/Kconfig | 6 + > drivers/gpu/drm/panel/Makefile | 1 + > drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c | 739 > +++++++++++++++++++++ > 5 files changed, 786 insertions(+) > create mode 100644 > Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt > create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c > ^ permalink raw reply [flat|nested] 31+ messages in thread
* [PATCH v10 0/3] Add support for the S6E3HA2 panel on TM2 board @ 2017-02-22 1:40 ` Hoegeun Kwon 0 siblings, 0 replies; 31+ messages in thread From: Hoegeun Kwon @ 2017-02-22 1:40 UTC (permalink / raw) To: linux-arm-kernel Hi all, This patchset is resent patchset. Because I have a missing TO, CC, I sent it again. Sorry, I will send it in the correct format next time. Best Regards, Hoegeun On 02/22/2017 10:09 AM, Hoegeun Kwon wrote: > Dear Thierry, > > I understand that your opinion is: > It is better to handle the error every time it is input to the > register, rather than error handling at once in the struct using > error. This not only makes the code easier to maintain, but also > reduces unnecessary computation. > > So I modified the panel driver to code-by-code error handling. > If this is not your opinion, could you tell me what your opinion? > > Best Regards, > Hoegeun > > > Changes for V10: > - Fixed code-by-code error handling. > > Changes for V9: > - Fixed the te-gpio to optional in bindings > > Changes for V8: > - Applied below two patches: (drm/exynos) > : drm/exynos: mic: Add mode_set callback function > : drm/exynos: mic: Fix parse_dt function > - The dt-binding patch and driver patch were divided. > - Rebase these patches on samsung SoC tree[1] and tm2 touckey patch[2]. > > Change for V7: > - Fixed the mode_set callback function of mic device driver. > because the mic register is initialized when entering suspend > mode, so should set the reg value whenever pre_enable is > called. > > Changes for V6: > - Fixed the parse_dt function of dsi device driver. > - Removed OF graph of panel in DT and DT binding document. > - Fixed the s6e3ha2 panel device driver. > - Fixed from number size to ARRAY_SIZE(). > - Fixed error handling in mipi_dsi_dcs_* functions. > - Fixed the clock of display_mode. > - Removed unnecessary casting and error log. > > Change for V5: > - The V5 has only one fix in V4 below. > - Removed the enable check of the mic driver in mode_set > callback, because mode_set should be performed every time. > > Changes for V4: > - Removed display-timings in devicetree, the display-timings has > been fixed to be provided by the device driver. > - Added the mode_set callback function into exynos_drm_mic, > because the exynos_drm_mic driver can not parse a videomode > struct by removing the display-timings from the devicetree. > > Changes for V3: > - In the DT binding document, made it clearly that the panel is a > child node of dsi. > - Fix reset-gpio active from high to low. > - Is the OF graph saying related to patch2? > Althogh the panel is a child of dsi, I think OF graph necessary. > because if a remote-endpoint is not specified, the dsi also > panel is not probed. > - The display-timings has been fixed to be provided by the device > driver. however, I think display-timings is necessary in dts. > because if dts does not have display-timings, dsi will not load. > > Changes for V2: > - Fixed the samsung,s6e3ha2.txt DT document. > - Added active high or low after the description of the GPIOs. > - Removed the reg and added a description of the virtual > channel number of a DSI peripheral. > > Depends on: > [1] https://git.kernel.org/cgit/linux/kernel/git/krzk/linux.git/ > (for-next branch) > [2] https://patchwork.kernel.org/patch/9504131/ > - ("arm64: dts: exynos: Add tm2 touchkey node") > > Hoegeun Kwon (2): > dt-bindings: Add support for samsung s6e3ha2 panel binding > drm/panel: Add support for S6E3HA2 panel driver on TM2 board > > Hyungwon Hwang (1): > arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board > > .../bindings/display/panel/samsung,s6e3ha2.txt | 28 + > arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 12 + > drivers/gpu/drm/panel/Kconfig | 6 + > drivers/gpu/drm/panel/Makefile | 1 + > drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c | 739 > +++++++++++++++++++++ > 5 files changed, 786 insertions(+) > create mode 100644 > Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt > create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c > ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: [PATCH v10 0/3] Add support for the S6E3HA2 panel on TM2 board @ 2017-02-22 1:40 ` Hoegeun Kwon 0 siblings, 0 replies; 31+ messages in thread From: Hoegeun Kwon @ 2017-02-22 1:40 UTC (permalink / raw) To: thierry.reding-Re5JQEeQqe8AvxtiuMwx3w, airlied-cv59FeDIM0c, robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8, catalin.marinas-5wv7dgnIgG8, will.deacon-5wv7dgnIgG8, kgene-DgEjT+Ai2ygdnm+yROfE0A, krzk-DgEjT+Ai2ygdnm+yROfE0A Cc: dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-samsung-soc-u79uwXL29TY76Z2rM5mHXA, linux-kernel-u79uwXL29TY76Z2rM5mHXA, javier-JPH+aEBZ4P+UEJcrhfAQsw, inki.dae-Sze3O3UU22JBDgjK7y7TUQ, a.hajda-Sze3O3UU22JBDgjK7y7TUQ, cw00.choi-Sze3O3UU22JBDgjK7y7TUQ, jh80.chung-Sze3O3UU22JBDgjK7y7TUQ, Andi Shyti, Hoegeun Kwon Hi all, This patchset is resent patchset. Because I have a missing TO, CC, I sent it again. Sorry, I will send it in the correct format next time. Best Regards, Hoegeun On 02/22/2017 10:09 AM, Hoegeun Kwon wrote: > Dear Thierry, > > I understand that your opinion is: > It is better to handle the error every time it is input to the > register, rather than error handling at once in the struct using > error. This not only makes the code easier to maintain, but also > reduces unnecessary computation. > > So I modified the panel driver to code-by-code error handling. > If this is not your opinion, could you tell me what your opinion? > > Best Regards, > Hoegeun > > > Changes for V10: > - Fixed code-by-code error handling. > > Changes for V9: > - Fixed the te-gpio to optional in bindings > > Changes for V8: > - Applied below two patches: (drm/exynos) > : drm/exynos: mic: Add mode_set callback function > : drm/exynos: mic: Fix parse_dt function > - The dt-binding patch and driver patch were divided. > - Rebase these patches on samsung SoC tree[1] and tm2 touckey patch[2]. > > Change for V7: > - Fixed the mode_set callback function of mic device driver. > because the mic register is initialized when entering suspend > mode, so should set the reg value whenever pre_enable is > called. > > Changes for V6: > - Fixed the parse_dt function of dsi device driver. > - Removed OF graph of panel in DT and DT binding document. > - Fixed the s6e3ha2 panel device driver. > - Fixed from number size to ARRAY_SIZE(). > - Fixed error handling in mipi_dsi_dcs_* functions. > - Fixed the clock of display_mode. > - Removed unnecessary casting and error log. > > Change for V5: > - The V5 has only one fix in V4 below. > - Removed the enable check of the mic driver in mode_set > callback, because mode_set should be performed every time. > > Changes for V4: > - Removed display-timings in devicetree, the display-timings has > been fixed to be provided by the device driver. > - Added the mode_set callback function into exynos_drm_mic, > because the exynos_drm_mic driver can not parse a videomode > struct by removing the display-timings from the devicetree. > > Changes for V3: > - In the DT binding document, made it clearly that the panel is a > child node of dsi. > - Fix reset-gpio active from high to low. > - Is the OF graph saying related to patch2? > Althogh the panel is a child of dsi, I think OF graph necessary. > because if a remote-endpoint is not specified, the dsi also > panel is not probed. > - The display-timings has been fixed to be provided by the device > driver. however, I think display-timings is necessary in dts. > because if dts does not have display-timings, dsi will not load. > > Changes for V2: > - Fixed the samsung,s6e3ha2.txt DT document. > - Added active high or low after the description of the GPIOs. > - Removed the reg and added a description of the virtual > channel number of a DSI peripheral. > > Depends on: > [1] https://git.kernel.org/cgit/linux/kernel/git/krzk/linux.git/ > (for-next branch) > [2] https://patchwork.kernel.org/patch/9504131/ > - ("arm64: dts: exynos: Add tm2 touchkey node") > > Hoegeun Kwon (2): > dt-bindings: Add support for samsung s6e3ha2 panel binding > drm/panel: Add support for S6E3HA2 panel driver on TM2 board > > Hyungwon Hwang (1): > arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board > > .../bindings/display/panel/samsung,s6e3ha2.txt | 28 + > arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 12 + > drivers/gpu/drm/panel/Kconfig | 6 + > drivers/gpu/drm/panel/Makefile | 1 + > drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c | 739 > +++++++++++++++++++++ > 5 files changed, 786 insertions(+) > create mode 100644 > Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt > create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 31+ messages in thread
end of thread, other threads:[~2017-03-07 20:23 UTC | newest] Thread overview: 31+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- [not found] <CGME20170220071000epcas1p38e002e5064bdf4c3b1b4886207dcaaf4@epcas1p3.samsung.com> 2017-02-20 7:09 ` [PATCH v10 0/3] Add support for the S6E3HA2 panel on TM2 board Hoegeun Kwon 2017-02-20 7:09 ` Hoegeun Kwon [not found] ` <CGME20170220071000epcas1p3fbc906fa085931b73b895b6724432cd3@epcas1p3.samsung.com> 2017-02-20 7:09 ` [PATCH v10 1/3] dt-bindings: Add support for samsung s6e3ha2 panel binding Hoegeun Kwon 2017-02-20 7:09 ` Hoegeun Kwon 2017-02-22 1:09 ` Hoegeun Kwon 2017-02-22 1:09 ` Hoegeun Kwon 2017-03-06 14:35 ` Javier Martinez Canillas 2017-03-06 14:35 ` Javier Martinez Canillas 2017-03-06 14:35 ` Javier Martinez Canillas [not found] ` <CGME20170220071001epcas1p3c2b32665942ba55c3ed4e06d2c66d661@epcas1p3.samsung.com> 2017-02-20 7:09 ` [PATCH v10 3/3] arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board Hoegeun Kwon 2017-02-20 7:09 ` Hoegeun Kwon 2017-02-20 13:20 ` Krzysztof Kozlowski 2017-02-22 1:09 ` Hoegeun Kwon 2017-02-22 1:09 ` Hoegeun Kwon 2017-02-22 1:09 ` Hoegeun Kwon 2017-03-06 14:42 ` Javier Martinez Canillas 2017-03-06 14:42 ` Javier Martinez Canillas 2017-03-06 14:42 ` Javier Martinez Canillas 2017-03-07 20:17 ` Krzysztof Kozlowski 2017-03-07 20:17 ` Krzysztof Kozlowski 2017-03-07 20:17 ` Krzysztof Kozlowski [not found] ` <CGME20170220071001epcas1p39f8f4b9dcd96c7fb2e808ed3b943dfd3@epcas1p3.samsung.com> 2017-02-20 7:09 ` [PATCH v10 2/3] drm/panel: Add support for S6E3HA2 panel driver " Hoegeun Kwon 2017-02-22 1:09 ` Hoegeun Kwon 2017-02-22 1:09 ` Hoegeun Kwon 2017-02-22 1:09 ` Hoegeun Kwon 2017-02-22 1:09 ` [PATCH v10 0/3] Add support for the S6E3HA2 panel " Hoegeun Kwon 2017-02-22 1:09 ` Hoegeun Kwon 2017-02-22 1:09 ` Hoegeun Kwon 2017-02-22 1:40 ` Hoegeun Kwon 2017-02-22 1:40 ` Hoegeun Kwon 2017-02-22 1:40 ` Hoegeun Kwon
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.