All of lore.kernel.org
 help / color / mirror / Atom feed
From: Vikas Manocha <vikas.manocha@st.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH v2 01/18] stm32f7: use clock driver to enable qspi controller clock
Date: Tue, 4 Apr 2017 14:45:03 -0700	[thread overview]
Message-ID: <1491342324-5820-2-git-send-email-vikas.manocha@st.com> (raw)
In-Reply-To: <1491342324-5820-1-git-send-email-vikas.manocha@st.com>

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
---
Changed in v2: None

 arch/arm/dts/stm32f746.dtsi |  1 +
 drivers/spi/stm32_qspi.c    | 16 +++++++++++++++-
 2 files changed, 16 insertions(+), 1 deletion(-)

diff --git a/arch/arm/dts/stm32f746.dtsi b/arch/arm/dts/stm32f746.dtsi
index b2b0b5f..883f818 100644
--- a/arch/arm/dts/stm32f746.dtsi
+++ b/arch/arm/dts/stm32f746.dtsi
@@ -78,6 +78,7 @@
 			reg-names = "QuadSPI", "QuadSPI-memory";
 			interrupts = <92>;
 			spi-max-frequency = <108000000>;
+			clocks = <&rcc 0 65>;
 			status = "disabled";
 		};
 		usart1: serial at 40011000 {
diff --git a/drivers/spi/stm32_qspi.c b/drivers/spi/stm32_qspi.c
index 05358eb..f0434a4 100644
--- a/drivers/spi/stm32_qspi.c
+++ b/drivers/spi/stm32_qspi.c
@@ -17,6 +17,7 @@
 #include <errno.h>
 #include <asm/arch/stm32.h>
 #include <asm/arch/stm32_defs.h>
+#include <clk.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -457,7 +458,20 @@ static int stm32_qspi_probe(struct udevice *bus)
 
 	priv->max_hz = plat->max_hz;
 
-	clock_setup(QSPI_CLOCK_CFG);
+#ifdef CONFIG_CLK
+	int ret;
+	struct clk clk;
+	ret = clk_get_by_index(bus, 0, &clk);
+	if (ret < 0)
+		return ret;
+
+	ret = clk_enable(&clk);
+
+	if (ret) {
+		dev_err(bus, "failed to enable clock\n");
+		return ret;
+	}
+#endif
 
 	setbits_le32(&priv->regs->cr, STM32_QSPI_CR_SSHIFT);
 
-- 
1.9.1

  reply	other threads:[~2017-04-04 21:45 UTC|newest]

Thread overview: 21+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-04-04 21:45 [U-Boot] [PATCH v2 00/18] stm32f7: add sdram & gpio drivers Vikas Manocha
2017-04-04 21:45 ` Vikas Manocha [this message]
2017-04-04 21:45 ` [U-Boot] [PATCH v2 02/18] stm32f7: sdram: move sdram driver code to ram drivers area Vikas Manocha
2017-04-04 21:45 ` [U-Boot] [PATCH v2 03/18] stm32f7: dm: add driver model support for sdram Vikas Manocha
2017-04-04 21:45 ` [U-Boot] [PATCH v2 04/18] ARM: DT: stm32f7: add sdram pin contol node Vikas Manocha
2017-04-04 21:45 ` [U-Boot] [PATCH v2 05/18] stm32f7: use driver model for sdram initialization Vikas Manocha
2017-04-04 21:45 ` [U-Boot] [PATCH v2 06/18] stm32f7: use clock driver to enable sdram controller clock Vikas Manocha
2017-04-04 21:45 ` [U-Boot] [PATCH v2 07/18] stm32f7: sdram: use sdram device tree node to configure sdram controller Vikas Manocha
2017-04-04 21:45 ` [U-Boot] [PATCH v2 08/18] dm: gpio: Add driver for stm32f7 gpio controller Vikas Manocha
2017-04-09 19:27   ` Simon Glass
2017-04-10 16:25     ` Vikas Manocha
2017-04-04 21:45 ` [U-Boot] [PATCH v2 09/18] ARM: DT: stm32f7: add gpio device tree nodes Vikas Manocha
2017-04-04 21:45 ` [U-Boot] [PATCH v2 10/18] stm32f7: use stm32f7 gpio driver supporting driver model Vikas Manocha
2017-04-04 21:45 ` [U-Boot] [PATCH v2 11/18] stm32f746: to switch on user LED1 & read user button Vikas Manocha
2017-04-04 21:45 ` [U-Boot] [PATCH v2 12/18] stm32f7: stm32f746-disco: read memory info from device tree Vikas Manocha
2017-04-04 21:45 ` [U-Boot] [PATCH v2 13/18] stm32f7: enable board info read " Vikas Manocha
2017-04-04 21:45 ` [U-Boot] [PATCH v2 14/18] stm32f7: sdram: correct sdram configuration as per micron sdram Vikas Manocha
2017-04-04 21:45 ` [U-Boot] [PATCH v2 15/18] stm32f7: increase the max no of pin configuration to 70 Vikas Manocha
2017-04-04 21:45 ` [U-Boot] [PATCH v2 16/18] stm32f7: move board specific pin muxing to dts Vikas Manocha
2017-04-04 21:45 ` [U-Boot] [PATCH v2 17/18] stm32f7: add support for stm32f769 disco board Vikas Manocha
2017-04-04 21:45 ` [U-Boot] [PATCH v2 18/18] stm32f7: remove not needed configuration from board config Vikas Manocha

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1491342324-5820-2-git-send-email-vikas.manocha@st.com \
    --to=vikas.manocha@st.com \
    --cc=u-boot@lists.denx.de \
    --subject='Re: [U-Boot] [PATCH v2 01/18] stm32f7: use clock driver to enable qspi controller clock' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.