* [TDLS PATCH V2 0/5] Add TDLS feature for ath10k
@ 2017-09-19 2:51 ` yintang
0 siblings, 0 replies; 14+ messages in thread
From: yintang @ 2017-09-19 2:51 UTC (permalink / raw)
To: ath10k; +Cc: linux-wireless
From: Yingying Tang <yintang@qti.qualcomm.com>
This patchset is for Rome PCIE chip, it will not affect other hardware
Yingying Tang (5):
mac80211: Enable TDLS peer buffer STA feature
ath10k: Enable TDLS peer buffer STA feature
ath10k: Enable TDLS peer inactivity detection
ath10k: Avoid to set WEP key for TDLS peer
ath10k: Avoid to set WEP key for TDLS peer
drivers/net/wireless/ath/ath10k/mac.c | 9 ++++-
drivers/net/wireless/ath/ath10k/wmi-tlv.c | 55 +++++++++++++++++++++++++++++
drivers/net/wireless/ath/ath10k/wmi-tlv.h | 23 ++++++++++++
drivers/net/wireless/ath/ath10k/wmi.h | 1 +
include/net/cfg80211.h | 3 ++
net/mac80211/tdls.c | 5 ++-
6 files changed, 94 insertions(+), 2 deletions(-)
--
1.7.9.5
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 14+ messages in thread
* [TDLS PATCH V2 1/5] mac80211: Enable TDLS peer buffer STA feature
2017-09-19 2:51 ` yintang
@ 2017-09-19 2:51 ` yintang
-1 siblings, 0 replies; 14+ messages in thread
From: yintang @ 2017-09-19 2:51 UTC (permalink / raw)
To: ath10k; +Cc: linux-wireless
From: Yingying Tang <yintang@qti.qualcomm.com>
Enable TDLS peer buffer STA feature.
Set extended capability bit to enable buffer STA when driver
support it.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
---
include/net/cfg80211.h | 3 +++
net/mac80211/tdls.c | 5 ++++-
2 files changed, 7 insertions(+), 1 deletion(-)
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index f12fa52..edefc25 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -3249,6 +3249,8 @@ struct cfg80211_ops {
* beaconing mode (AP, IBSS, Mesh, ...).
* @WIPHY_FLAG_HAS_STATIC_WEP: The device supports static WEP key installation
* before connection.
+ * @WIPHY_FLAG_SUPPORT_TDLS_BUFFER_ST: Device support buffer STA when TDLS is
+ * established.
*/
enum wiphy_flags {
/* use hole at 0 */
@@ -3275,6 +3277,7 @@ enum wiphy_flags {
WIPHY_FLAG_SUPPORTS_5_10_MHZ = BIT(22),
WIPHY_FLAG_HAS_CHANNEL_SWITCH = BIT(23),
WIPHY_FLAG_HAS_STATIC_WEP = BIT(24),
+ WIPHY_FLAG_SUPPORT_TDLS_BUFFER_STA = BIT(25),
};
/**
diff --git a/net/mac80211/tdls.c b/net/mac80211/tdls.c
index 91093d4..f99e379 100644
--- a/net/mac80211/tdls.c
+++ b/net/mac80211/tdls.c
@@ -49,6 +49,8 @@ static void ieee80211_tdls_add_ext_capab(struct ieee80211_sub_if_data *sdata,
!ifmgd->tdls_wider_bw_prohibited;
struct ieee80211_supported_band *sband = ieee80211_get_sband(sdata);
bool vht = sband && sband->vht_cap.vht_supported;
+ bool buffer_sta =
+ local->hw.wiphy->flags & WIPHY_FLAG_SUPPORT_TDLS_BUFFER_STA;
u8 *pos = skb_put(skb, 10);
*pos++ = WLAN_EID_EXT_CAPABILITY;
@@ -56,7 +58,8 @@ static void ieee80211_tdls_add_ext_capab(struct ieee80211_sub_if_data *sdata,
*pos++ = 0x0;
*pos++ = 0x0;
*pos++ = 0x0;
- *pos++ = chan_switch ? WLAN_EXT_CAPA4_TDLS_CHAN_SWITCH : 0;
+ *pos++ = (chan_switch ? WLAN_EXT_CAPA4_TDLS_CHAN_SWITCH : 0) |
+ (buffer_sta ? WLAN_EXT_CAPA4_TDLS_BUFFER_STA : 0);
*pos++ = WLAN_EXT_CAPA5_TDLS_ENABLED;
*pos++ = 0;
*pos++ = 0;
--
1.7.9.5
^ permalink raw reply related [flat|nested] 14+ messages in thread* [TDLS PATCH V2 1/5] mac80211: Enable TDLS peer buffer STA feature
@ 2017-09-19 2:51 ` yintang
0 siblings, 0 replies; 14+ messages in thread
From: yintang @ 2017-09-19 2:51 UTC (permalink / raw)
To: ath10k; +Cc: linux-wireless
From: Yingying Tang <yintang@qti.qualcomm.com>
Enable TDLS peer buffer STA feature.
Set extended capability bit to enable buffer STA when driver
support it.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
---
include/net/cfg80211.h | 3 +++
net/mac80211/tdls.c | 5 ++++-
2 files changed, 7 insertions(+), 1 deletion(-)
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index f12fa52..edefc25 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -3249,6 +3249,8 @@ struct cfg80211_ops {
* beaconing mode (AP, IBSS, Mesh, ...).
* @WIPHY_FLAG_HAS_STATIC_WEP: The device supports static WEP key installation
* before connection.
+ * @WIPHY_FLAG_SUPPORT_TDLS_BUFFER_ST: Device support buffer STA when TDLS is
+ * established.
*/
enum wiphy_flags {
/* use hole at 0 */
@@ -3275,6 +3277,7 @@ enum wiphy_flags {
WIPHY_FLAG_SUPPORTS_5_10_MHZ = BIT(22),
WIPHY_FLAG_HAS_CHANNEL_SWITCH = BIT(23),
WIPHY_FLAG_HAS_STATIC_WEP = BIT(24),
+ WIPHY_FLAG_SUPPORT_TDLS_BUFFER_STA = BIT(25),
};
/**
diff --git a/net/mac80211/tdls.c b/net/mac80211/tdls.c
index 91093d4..f99e379 100644
--- a/net/mac80211/tdls.c
+++ b/net/mac80211/tdls.c
@@ -49,6 +49,8 @@ static void ieee80211_tdls_add_ext_capab(struct ieee80211_sub_if_data *sdata,
!ifmgd->tdls_wider_bw_prohibited;
struct ieee80211_supported_band *sband = ieee80211_get_sband(sdata);
bool vht = sband && sband->vht_cap.vht_supported;
+ bool buffer_sta =
+ local->hw.wiphy->flags & WIPHY_FLAG_SUPPORT_TDLS_BUFFER_STA;
u8 *pos = skb_put(skb, 10);
*pos++ = WLAN_EID_EXT_CAPABILITY;
@@ -56,7 +58,8 @@ static void ieee80211_tdls_add_ext_capab(struct ieee80211_sub_if_data *sdata,
*pos++ = 0x0;
*pos++ = 0x0;
*pos++ = 0x0;
- *pos++ = chan_switch ? WLAN_EXT_CAPA4_TDLS_CHAN_SWITCH : 0;
+ *pos++ = (chan_switch ? WLAN_EXT_CAPA4_TDLS_CHAN_SWITCH : 0) |
+ (buffer_sta ? WLAN_EXT_CAPA4_TDLS_BUFFER_STA : 0);
*pos++ = WLAN_EXT_CAPA5_TDLS_ENABLED;
*pos++ = 0;
*pos++ = 0;
--
1.7.9.5
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply related [flat|nested] 14+ messages in thread* Re: [TDLS PATCH V2 1/5] mac80211: Enable TDLS peer buffer STA feature
2017-09-19 2:51 ` yintang
@ 2017-09-19 3:01 ` James Cameron
-1 siblings, 0 replies; 14+ messages in thread
From: James Cameron @ 2017-09-19 3:01 UTC (permalink / raw)
To: yintang; +Cc: ath10k, linux-wireless
On Tue, Sep 19, 2017 at 10:51:04AM +0800, yintang@qti.qualcomm.com wrote:
> From: Yingying Tang <yintang@qti.qualcomm.com>
>
> Enable TDLS peer buffer STA feature.
> Set extended capability bit to enable buffer STA when driver
> support it.
>
> Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
> ---
> include/net/cfg80211.h | 3 +++
> net/mac80211/tdls.c | 5 ++++-
> 2 files changed, 7 insertions(+), 1 deletion(-)
>
> diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
> index f12fa52..edefc25 100644
> --- a/include/net/cfg80211.h
> +++ b/include/net/cfg80211.h
> @@ -3249,6 +3249,8 @@ struct cfg80211_ops {
> * beaconing mode (AP, IBSS, Mesh, ...).
> * @WIPHY_FLAG_HAS_STATIC_WEP: The device supports static WEP key installation
> * before connection.
> + * @WIPHY_FLAG_SUPPORT_TDLS_BUFFER_ST: Device support buffer STA when TDLS is
"_ST:" should be "_STA:"
> + * established.
> */
> enum wiphy_flags {
> /* use hole at 0 */
> @@ -3275,6 +3277,7 @@ enum wiphy_flags {
> WIPHY_FLAG_SUPPORTS_5_10_MHZ = BIT(22),
> WIPHY_FLAG_HAS_CHANNEL_SWITCH = BIT(23),
> WIPHY_FLAG_HAS_STATIC_WEP = BIT(24),
> + WIPHY_FLAG_SUPPORT_TDLS_BUFFER_STA = BIT(25),
> };
>
> /**
> [...]
--
James Cameron
http://quozl.netrek.org/
^ permalink raw reply [flat|nested] 14+ messages in thread* Re: [TDLS PATCH V2 1/5] mac80211: Enable TDLS peer buffer STA feature
@ 2017-09-19 3:01 ` James Cameron
0 siblings, 0 replies; 14+ messages in thread
From: James Cameron @ 2017-09-19 3:01 UTC (permalink / raw)
To: yintang; +Cc: linux-wireless, ath10k
On Tue, Sep 19, 2017 at 10:51:04AM +0800, yintang@qti.qualcomm.com wrote:
> From: Yingying Tang <yintang@qti.qualcomm.com>
>
> Enable TDLS peer buffer STA feature.
> Set extended capability bit to enable buffer STA when driver
> support it.
>
> Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
> ---
> include/net/cfg80211.h | 3 +++
> net/mac80211/tdls.c | 5 ++++-
> 2 files changed, 7 insertions(+), 1 deletion(-)
>
> diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
> index f12fa52..edefc25 100644
> --- a/include/net/cfg80211.h
> +++ b/include/net/cfg80211.h
> @@ -3249,6 +3249,8 @@ struct cfg80211_ops {
> * beaconing mode (AP, IBSS, Mesh, ...).
> * @WIPHY_FLAG_HAS_STATIC_WEP: The device supports static WEP key installation
> * before connection.
> + * @WIPHY_FLAG_SUPPORT_TDLS_BUFFER_ST: Device support buffer STA when TDLS is
"_ST:" should be "_STA:"
> + * established.
> */
> enum wiphy_flags {
> /* use hole at 0 */
> @@ -3275,6 +3277,7 @@ enum wiphy_flags {
> WIPHY_FLAG_SUPPORTS_5_10_MHZ = BIT(22),
> WIPHY_FLAG_HAS_CHANNEL_SWITCH = BIT(23),
> WIPHY_FLAG_HAS_STATIC_WEP = BIT(24),
> + WIPHY_FLAG_SUPPORT_TDLS_BUFFER_STA = BIT(25),
> };
>
> /**
> [...]
--
James Cameron
http://quozl.netrek.org/
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 14+ messages in thread
* [TDLS PATCH V2 2/5] ath10k: Enable TDLS peer buffer STA feature
2017-09-19 2:51 ` yintang
@ 2017-09-19 2:51 ` yintang
-1 siblings, 0 replies; 14+ messages in thread
From: yintang @ 2017-09-19 2:51 UTC (permalink / raw)
To: ath10k; +Cc: linux-wireless
From: Yingying Tang <yintang@qti.qualcomm.com>
Enable TDLS peer buffer STA feature.
QCA6174 firmware(version: WLAN.RM.4.4) support TDLS peer buffer STA,
it reports this capability through wmi service map in wmi service ready
event. Set related parameter in TDLS WMI command to enable this feature.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
---
drivers/net/wireless/ath/ath10k/mac.c | 3 +++
drivers/net/wireless/ath/ath10k/wmi-tlv.c | 3 +++
2 files changed, 6 insertions(+)
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index 5683f1a..399f9ba 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -8204,6 +8204,9 @@ int ath10k_mac_register(struct ath10k *ar)
ieee80211_hw_set(ar->hw, TDLS_WIDER_BW);
}
+ if (test_bit(WMI_SERVICE_TDLS_UAPSD_BUFFER_STA, ar->wmi.svc_map))
+ ar->hw->wiphy->flags |= WIPHY_FLAG_SUPPORT_TDLS_BUFFER_STA;
+
ar->hw->wiphy->flags |= WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL;
ar->hw->wiphy->flags |= WIPHY_FLAG_HAS_CHANNEL_SWITCH;
ar->hw->wiphy->max_remain_on_channel_duration = 5000;
diff --git a/drivers/net/wireless/ath/ath10k/wmi-tlv.c b/drivers/net/wireless/ath/ath10k/wmi-tlv.c
index 7616c1c..f60b46e 100644
--- a/drivers/net/wireless/ath/ath10k/wmi-tlv.c
+++ b/drivers/net/wireless/ath/ath10k/wmi-tlv.c
@@ -2747,6 +2747,9 @@ static void *ath10k_wmi_tlv_put_wmm(void *ptr,
*/
u32 options = 0;
+ if (test_bit(WMI_SERVICE_TDLS_UAPSD_BUFFER_STA, ar->wmi.svc_map))
+ options |= WMI_TLV_TDLS_BUFFER_STA_EN;
+
len = sizeof(*tlv) + sizeof(*cmd);
skb = ath10k_wmi_alloc_skb(ar, len);
if (!skb)
--
1.7.9.5
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [TDLS PATCH V2 2/5] ath10k: Enable TDLS peer buffer STA feature
@ 2017-09-19 2:51 ` yintang
0 siblings, 0 replies; 14+ messages in thread
From: yintang @ 2017-09-19 2:51 UTC (permalink / raw)
To: ath10k; +Cc: linux-wireless
From: Yingying Tang <yintang@qti.qualcomm.com>
Enable TDLS peer buffer STA feature.
QCA6174 firmware(version: WLAN.RM.4.4) support TDLS peer buffer STA,
it reports this capability through wmi service map in wmi service ready
event. Set related parameter in TDLS WMI command to enable this feature.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
---
drivers/net/wireless/ath/ath10k/mac.c | 3 +++
drivers/net/wireless/ath/ath10k/wmi-tlv.c | 3 +++
2 files changed, 6 insertions(+)
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index 5683f1a..399f9ba 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -8204,6 +8204,9 @@ int ath10k_mac_register(struct ath10k *ar)
ieee80211_hw_set(ar->hw, TDLS_WIDER_BW);
}
+ if (test_bit(WMI_SERVICE_TDLS_UAPSD_BUFFER_STA, ar->wmi.svc_map))
+ ar->hw->wiphy->flags |= WIPHY_FLAG_SUPPORT_TDLS_BUFFER_STA;
+
ar->hw->wiphy->flags |= WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL;
ar->hw->wiphy->flags |= WIPHY_FLAG_HAS_CHANNEL_SWITCH;
ar->hw->wiphy->max_remain_on_channel_duration = 5000;
diff --git a/drivers/net/wireless/ath/ath10k/wmi-tlv.c b/drivers/net/wireless/ath/ath10k/wmi-tlv.c
index 7616c1c..f60b46e 100644
--- a/drivers/net/wireless/ath/ath10k/wmi-tlv.c
+++ b/drivers/net/wireless/ath/ath10k/wmi-tlv.c
@@ -2747,6 +2747,9 @@ static void *ath10k_wmi_tlv_put_wmm(void *ptr,
*/
u32 options = 0;
+ if (test_bit(WMI_SERVICE_TDLS_UAPSD_BUFFER_STA, ar->wmi.svc_map))
+ options |= WMI_TLV_TDLS_BUFFER_STA_EN;
+
len = sizeof(*tlv) + sizeof(*cmd);
skb = ath10k_wmi_alloc_skb(ar, len);
if (!skb)
--
1.7.9.5
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [TDLS PATCH V2 3/5] ath10k: Enable TDLS peer inactivity detection
2017-09-19 2:51 ` yintang
@ 2017-09-19 2:51 ` yintang
-1 siblings, 0 replies; 14+ messages in thread
From: yintang @ 2017-09-19 2:51 UTC (permalink / raw)
To: ath10k; +Cc: linux-wireless
From: Yingying Tang <yintang@qti.qualcomm.com>
Enable TDLS peer inactivity detetion feature.
QCA6174 firmware(version: WLAN.RM.4.4) support TDLS link inactivity detecting.
Set related parameters in TDLS WMI command to enable this feature.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
---
drivers/net/wireless/ath/ath10k/wmi-tlv.c | 52 +++++++++++++++++++++++++++++
drivers/net/wireless/ath/ath10k/wmi-tlv.h | 23 +++++++++++++
drivers/net/wireless/ath/ath10k/wmi.h | 1 +
3 files changed, 76 insertions(+)
diff --git a/drivers/net/wireless/ath/ath10k/wmi-tlv.c b/drivers/net/wireless/ath/ath10k/wmi-tlv.c
index f60b46e..63bb2c4 100644
--- a/drivers/net/wireless/ath/ath10k/wmi-tlv.c
+++ b/drivers/net/wireless/ath/ath10k/wmi-tlv.c
@@ -412,6 +412,49 @@ static int ath10k_wmi_tlv_event_tx_pause(struct ath10k *ar,
return 0;
}
+void ath10k_wmi_event_tdls_peer(struct ath10k *ar, struct sk_buff *skb)
+{
+ struct ieee80211_sta *station;
+ const struct wmi_tlv_tdls_peer_event *ev;
+ const void **tb;
+ struct ath10k_vif *arvif;
+
+ tb = ath10k_wmi_tlv_parse_alloc(ar, skb->data, skb->len, GFP_ATOMIC);
+ if (IS_ERR(tb)) {
+ ath10k_warn(ar, "tdls peer failed to parse tlv");
+ return;
+ }
+ ev = tb[WMI_TLV_TAG_STRUCT_TDLS_PEER_EVENT];
+ if (!ev) {
+ kfree(tb);
+ ath10k_warn(ar, "tdls peer NULL event");
+ return;
+ }
+
+ switch (ev->peer_reason) {
+ case WMI_TDLS_TEARDOWN_REASON_TX:
+ case WMI_TDLS_TEARDOWN_REASON_RSSI:
+ case WMI_TDLS_TEARDOWN_REASON_PTR_TIMEOUT:
+ station = ieee80211_find_sta_by_ifaddr(ar->hw,
+ ev->peer_macaddr.addr,
+ NULL);
+ if (!station) {
+ ath10k_warn(ar, "did not find station from tdls peer event");
+ kfree(tb);
+ return;
+ }
+ arvif = ath10k_get_arvif(ar, ev->vdev_id);
+ ieee80211_tdls_oper_request(
+ arvif->vif, station->addr,
+ NL80211_TDLS_TEARDOWN,
+ WLAN_REASON_TDLS_TEARDOWN_UNREACHABLE,
+ GFP_ATOMIC
+ );
+ break;
+ }
+ kfree(tb);
+}
+
/***********/
/* TLV ops */
/***********/
@@ -552,6 +595,9 @@ static void ath10k_wmi_tlv_op_rx(struct ath10k *ar, struct sk_buff *skb)
case WMI_TLV_TX_PAUSE_EVENTID:
ath10k_wmi_tlv_event_tx_pause(ar, skb);
break;
+ case WMI_TLV_TDLS_PEER_EVENTID:
+ ath10k_wmi_event_tdls_peer(ar, skb);
+ break;
default:
ath10k_warn(ar, "Unknown eventid: %d\n", id);
break;
@@ -2750,6 +2796,12 @@ static void *ath10k_wmi_tlv_put_wmm(void *ptr,
if (test_bit(WMI_SERVICE_TDLS_UAPSD_BUFFER_STA, ar->wmi.svc_map))
options |= WMI_TLV_TDLS_BUFFER_STA_EN;
+ /* WMI_TDLS_ENABLE_ACTIVE_EXTERNAL_CONTROL means firm will handle TDLS
+ * link inactivity detecting logic.
+ */
+ if (state == WMI_TDLS_ENABLE_ACTIVE)
+ state = WMI_TDLS_ENABLE_ACTIVE_EXTERNAL_CONTROL;
+
len = sizeof(*tlv) + sizeof(*cmd);
skb = ath10k_wmi_alloc_skb(ar, len);
if (!skb)
diff --git a/drivers/net/wireless/ath/ath10k/wmi-tlv.h b/drivers/net/wireless/ath/ath10k/wmi-tlv.h
index 22cf011..00d68c5 100644
--- a/drivers/net/wireless/ath/ath10k/wmi-tlv.h
+++ b/drivers/net/wireless/ath/ath10k/wmi-tlv.h
@@ -1641,6 +1641,29 @@ struct wmi_tlv_tx_pause_ev {
__le32 tid_map;
} __packed;
+struct wmi_tlv_tdls_peer_event {
+ struct wmi_mac_addr peer_macaddr;
+ __le32 peer_status;
+ __le32 peer_reason;
+ __le32 vdev_id;
+} __packed;
+
+enum wmi_tdls_peer_reason {
+ WMI_TDLS_TEARDOWN_REASON_TX,
+ WMI_TDLS_TEARDOWN_REASON_RSSI,
+ WMI_TDLS_TEARDOWN_REASON_SCAN,
+ WMI_TDLS_DISCONNECTED_REASON_PEER_DELETE,
+ WMI_TDLS_TEARDOWN_REASON_PTR_TIMEOUT,
+ WMI_TDLS_TEARDOWN_REASON_BAD_PTR,
+ WMI_TDLS_TEARDOWN_REASON_NO_RESPONSE,
+ WMI_TDLS_ENTER_BUF_STA,
+ WMI_TDLS_EXIT_BUF_STA,
+ WMI_TDLS_ENTER_BT_BUSY_MODE,
+ WMI_TDLS_EXIT_BT_BUSY_MODE,
+ WMI_TDLS_SCAN_STARTED_EVENT,
+ WMI_TDLS_SCAN_COMPLETED_EVENT,
+};
+
void ath10k_wmi_tlv_attach(struct ath10k *ar);
#endif
diff --git a/drivers/net/wireless/ath/ath10k/wmi.h b/drivers/net/wireless/ath/ath10k/wmi.h
index 7a3606d..74a6c78 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.h
+++ b/drivers/net/wireless/ath/ath10k/wmi.h
@@ -6720,6 +6720,7 @@ enum wmi_tdls_state {
WMI_TDLS_DISABLE,
WMI_TDLS_ENABLE_PASSIVE,
WMI_TDLS_ENABLE_ACTIVE,
+ WMI_TDLS_ENABLE_ACTIVE_EXTERNAL_CONTROL,
};
enum wmi_tdls_peer_state {
--
1.7.9.5
^ permalink raw reply related [flat|nested] 14+ messages in thread* [TDLS PATCH V2 3/5] ath10k: Enable TDLS peer inactivity detection
@ 2017-09-19 2:51 ` yintang
0 siblings, 0 replies; 14+ messages in thread
From: yintang @ 2017-09-19 2:51 UTC (permalink / raw)
To: ath10k; +Cc: linux-wireless
From: Yingying Tang <yintang@qti.qualcomm.com>
Enable TDLS peer inactivity detetion feature.
QCA6174 firmware(version: WLAN.RM.4.4) support TDLS link inactivity detecting.
Set related parameters in TDLS WMI command to enable this feature.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
---
drivers/net/wireless/ath/ath10k/wmi-tlv.c | 52 +++++++++++++++++++++++++++++
drivers/net/wireless/ath/ath10k/wmi-tlv.h | 23 +++++++++++++
drivers/net/wireless/ath/ath10k/wmi.h | 1 +
3 files changed, 76 insertions(+)
diff --git a/drivers/net/wireless/ath/ath10k/wmi-tlv.c b/drivers/net/wireless/ath/ath10k/wmi-tlv.c
index f60b46e..63bb2c4 100644
--- a/drivers/net/wireless/ath/ath10k/wmi-tlv.c
+++ b/drivers/net/wireless/ath/ath10k/wmi-tlv.c
@@ -412,6 +412,49 @@ static int ath10k_wmi_tlv_event_tx_pause(struct ath10k *ar,
return 0;
}
+void ath10k_wmi_event_tdls_peer(struct ath10k *ar, struct sk_buff *skb)
+{
+ struct ieee80211_sta *station;
+ const struct wmi_tlv_tdls_peer_event *ev;
+ const void **tb;
+ struct ath10k_vif *arvif;
+
+ tb = ath10k_wmi_tlv_parse_alloc(ar, skb->data, skb->len, GFP_ATOMIC);
+ if (IS_ERR(tb)) {
+ ath10k_warn(ar, "tdls peer failed to parse tlv");
+ return;
+ }
+ ev = tb[WMI_TLV_TAG_STRUCT_TDLS_PEER_EVENT];
+ if (!ev) {
+ kfree(tb);
+ ath10k_warn(ar, "tdls peer NULL event");
+ return;
+ }
+
+ switch (ev->peer_reason) {
+ case WMI_TDLS_TEARDOWN_REASON_TX:
+ case WMI_TDLS_TEARDOWN_REASON_RSSI:
+ case WMI_TDLS_TEARDOWN_REASON_PTR_TIMEOUT:
+ station = ieee80211_find_sta_by_ifaddr(ar->hw,
+ ev->peer_macaddr.addr,
+ NULL);
+ if (!station) {
+ ath10k_warn(ar, "did not find station from tdls peer event");
+ kfree(tb);
+ return;
+ }
+ arvif = ath10k_get_arvif(ar, ev->vdev_id);
+ ieee80211_tdls_oper_request(
+ arvif->vif, station->addr,
+ NL80211_TDLS_TEARDOWN,
+ WLAN_REASON_TDLS_TEARDOWN_UNREACHABLE,
+ GFP_ATOMIC
+ );
+ break;
+ }
+ kfree(tb);
+}
+
/***********/
/* TLV ops */
/***********/
@@ -552,6 +595,9 @@ static void ath10k_wmi_tlv_op_rx(struct ath10k *ar, struct sk_buff *skb)
case WMI_TLV_TX_PAUSE_EVENTID:
ath10k_wmi_tlv_event_tx_pause(ar, skb);
break;
+ case WMI_TLV_TDLS_PEER_EVENTID:
+ ath10k_wmi_event_tdls_peer(ar, skb);
+ break;
default:
ath10k_warn(ar, "Unknown eventid: %d\n", id);
break;
@@ -2750,6 +2796,12 @@ static void *ath10k_wmi_tlv_put_wmm(void *ptr,
if (test_bit(WMI_SERVICE_TDLS_UAPSD_BUFFER_STA, ar->wmi.svc_map))
options |= WMI_TLV_TDLS_BUFFER_STA_EN;
+ /* WMI_TDLS_ENABLE_ACTIVE_EXTERNAL_CONTROL means firm will handle TDLS
+ * link inactivity detecting logic.
+ */
+ if (state == WMI_TDLS_ENABLE_ACTIVE)
+ state = WMI_TDLS_ENABLE_ACTIVE_EXTERNAL_CONTROL;
+
len = sizeof(*tlv) + sizeof(*cmd);
skb = ath10k_wmi_alloc_skb(ar, len);
if (!skb)
diff --git a/drivers/net/wireless/ath/ath10k/wmi-tlv.h b/drivers/net/wireless/ath/ath10k/wmi-tlv.h
index 22cf011..00d68c5 100644
--- a/drivers/net/wireless/ath/ath10k/wmi-tlv.h
+++ b/drivers/net/wireless/ath/ath10k/wmi-tlv.h
@@ -1641,6 +1641,29 @@ struct wmi_tlv_tx_pause_ev {
__le32 tid_map;
} __packed;
+struct wmi_tlv_tdls_peer_event {
+ struct wmi_mac_addr peer_macaddr;
+ __le32 peer_status;
+ __le32 peer_reason;
+ __le32 vdev_id;
+} __packed;
+
+enum wmi_tdls_peer_reason {
+ WMI_TDLS_TEARDOWN_REASON_TX,
+ WMI_TDLS_TEARDOWN_REASON_RSSI,
+ WMI_TDLS_TEARDOWN_REASON_SCAN,
+ WMI_TDLS_DISCONNECTED_REASON_PEER_DELETE,
+ WMI_TDLS_TEARDOWN_REASON_PTR_TIMEOUT,
+ WMI_TDLS_TEARDOWN_REASON_BAD_PTR,
+ WMI_TDLS_TEARDOWN_REASON_NO_RESPONSE,
+ WMI_TDLS_ENTER_BUF_STA,
+ WMI_TDLS_EXIT_BUF_STA,
+ WMI_TDLS_ENTER_BT_BUSY_MODE,
+ WMI_TDLS_EXIT_BT_BUSY_MODE,
+ WMI_TDLS_SCAN_STARTED_EVENT,
+ WMI_TDLS_SCAN_COMPLETED_EVENT,
+};
+
void ath10k_wmi_tlv_attach(struct ath10k *ar);
#endif
diff --git a/drivers/net/wireless/ath/ath10k/wmi.h b/drivers/net/wireless/ath/ath10k/wmi.h
index 7a3606d..74a6c78 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.h
+++ b/drivers/net/wireless/ath/ath10k/wmi.h
@@ -6720,6 +6720,7 @@ enum wmi_tdls_state {
WMI_TDLS_DISABLE,
WMI_TDLS_ENABLE_PASSIVE,
WMI_TDLS_ENABLE_ACTIVE,
+ WMI_TDLS_ENABLE_ACTIVE_EXTERNAL_CONTROL,
};
enum wmi_tdls_peer_state {
--
1.7.9.5
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [TDLS PATCH V2 4/5] ath10k: Avoid to set WEP key for TDLS peer
2017-09-19 2:51 ` yintang
@ 2017-09-19 2:51 ` yintang
-1 siblings, 0 replies; 14+ messages in thread
From: yintang @ 2017-09-19 2:51 UTC (permalink / raw)
To: ath10k; +Cc: linux-wireless
From: Yingying Tang <yintang@qti.qualcomm.com>
TDLS peer do not need WEP key. Setting WEP key will lead
to TDLS setup failure. Add fix to avoid setting WEP key
for TDLS peer.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
---
drivers/net/wireless/ath/ath10k/mac.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index 399f9ba..f6702cb 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -2966,7 +2966,7 @@ static int ath10k_station_assoc(struct ath10k *ar,
}
/* Plumb cached keys only for static WEP */
- if (arvif->def_wep_key_idx != -1) {
+ if ((arvif->def_wep_key_idx != -1) && (!sta->tdls)) {
ret = ath10k_install_peer_wep_keys(arvif, sta->addr);
if (ret) {
ath10k_warn(ar, "failed to install peer wep keys for vdev %i: %d\n",
--
1.7.9.5
^ permalink raw reply related [flat|nested] 14+ messages in thread* [TDLS PATCH V2 4/5] ath10k: Avoid to set WEP key for TDLS peer
@ 2017-09-19 2:51 ` yintang
0 siblings, 0 replies; 14+ messages in thread
From: yintang @ 2017-09-19 2:51 UTC (permalink / raw)
To: ath10k; +Cc: linux-wireless
From: Yingying Tang <yintang@qti.qualcomm.com>
TDLS peer do not need WEP key. Setting WEP key will lead
to TDLS setup failure. Add fix to avoid setting WEP key
for TDLS peer.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
---
drivers/net/wireless/ath/ath10k/mac.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index 399f9ba..f6702cb 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -2966,7 +2966,7 @@ static int ath10k_station_assoc(struct ath10k *ar,
}
/* Plumb cached keys only for static WEP */
- if (arvif->def_wep_key_idx != -1) {
+ if ((arvif->def_wep_key_idx != -1) && (!sta->tdls)) {
ret = ath10k_install_peer_wep_keys(arvif, sta->addr);
if (ret) {
ath10k_warn(ar, "failed to install peer wep keys for vdev %i: %d\n",
--
1.7.9.5
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply related [flat|nested] 14+ messages in thread