From: Neil Armstrong <narmstrong@baylibre.com> To: maxime.ripard@bootlin.com, wens@csie.org Cc: Neil Armstrong <narmstrong@baylibre.com>, clabbe@baylibre.com, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org Subject: [PATCH v2 1/2] arm: dts: sun8i: h3: libretech-all-h3-cc: Move board definition to common dtsi Date: Tue, 24 Apr 2018 13:47:13 +0200 [thread overview] Message-ID: <1524570434-17814-2-git-send-email-narmstrong@baylibre.com> (raw) In-Reply-To: <1524570434-17814-1-git-send-email-narmstrong@baylibre.com> Since the libretech-all-h3-cc can use either the H2+, H3 or H5, move the content of the dts file to a common dtsi file to be included by the H3 variant and in a following patch the H5 variant. By the way, update the SPDX licence tag position. Suggested-by: Corentin Labbe <clabbe@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> --- arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts | 213 +------------------- arch/arm/boot/dts/sunxi-libretech-all-h3-cc.dtsi | 215 +++++++++++++++++++++ 2 files changed, 217 insertions(+), 211 deletions(-) create mode 100644 arch/arm/boot/dts/sunxi-libretech-all-h3-cc.dtsi diff --git a/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts b/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts index 5971b8b..50f2fb3 100644 --- a/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts +++ b/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts @@ -1,222 +1,13 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) /* * Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org> - * - * SPDX-License-Identifier: (GPL-2.0+ OR MIT) */ /dts-v1/; #include "sun8i-h3.dtsi" - -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/input/input.h> +#include "sunxi-libretech-all-h3-cc.dtsi" / { model = "Libre Computer Board ALL-H3-CC H3"; compatible = "libretech,all-h3-cc-h3", "allwinner,sun8i-h3"; - - aliases { - ethernet0 = &emac; - serial0 = &uart0; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - connector { - compatible = "hdmi-connector"; - type = "a"; - - port { - hdmi_con_in: endpoint { - remote-endpoint = <&hdmi_out_con>; - }; - }; - }; - - leds { - compatible = "gpio-leds"; - - pwr_led { - label = "librecomputer:green:pwr"; - gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */ - default-state = "on"; - }; - - status_led { - label = "librecomputer:blue:status"; - gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */ - }; - }; - - gpio_keys { - compatible = "gpio-keys"; - - power { - label = "power"; - linux,code = <KEY_POWER>; - gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */ - }; - }; - - reg_vcc1v2: vcc1v2 { - compatible = "regulator-fixed"; - regulator-name = "vcc1v2"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-boot-on; - vin-supply = <®_vcc5v0>; - gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ - enable-active-high; - }; - - reg_vcc3v3: vcc3v3 { - compatible = "regulator-fixed"; - regulator-name = "vcc3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - vin-supply = <®_vcc5v0>; - }; - - /* This represents the board's 5V input */ - reg_vcc5v0: vcc5v0 { - compatible = "regulator-fixed"; - regulator-name = "vcc5v0"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - }; - - reg_vcc_dram: vcc-dram { - compatible = "regulator-fixed"; - regulator-name = "vcc-dram"; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1500000>; - regulator-always-on; - regulator-boot-on; - vin-supply = <®_vcc5v0>; - gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */ - enable-active-high; - }; - - reg_vcc_io: vcc-io { - compatible = "regulator-fixed"; - regulator-name = "vcc-io"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-boot-on; - vin-supply = <®_vcc3v3>; - gpio = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL5 */ - }; - - reg_vdd_cpux: vdd-cpux { - compatible = "regulator-fixed"; - regulator-name = "vdd-cpux"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - regulator-always-on; - regulator-boot-on; - vin-supply = <®_vcc5v0>; - gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ - enable-active-high; - }; -}; - -&codec { - allwinner,audio-routing = - "Line Out", "LINEOUT", - "MIC1", "Mic", - "Mic", "MBIAS"; - status = "okay"; -}; - -&cpu0 { - cpu-supply = <®_vdd_cpux>; -}; - -&de { - status = "okay"; -}; - -&ehci0 { - status = "okay"; -}; - -&ehci1 { - status = "okay"; -}; - -&ehci2 { - status = "okay"; -}; - -&ehci3 { - status = "okay"; -}; - -&emac { - phy-handle = <&int_mii_phy>; - phy-mode = "mii"; - allwinner,leds-active-low; - status = "okay"; -}; - -&hdmi { - status = "okay"; -}; - -&hdmi_out { - hdmi_out_con: endpoint { - remote-endpoint = <&hdmi_con_in>; - }; -}; - -&ir { - pinctrl-names = "default"; - pinctrl-0 = <&ir_pins_a>; - status = "okay"; -}; - -&mmc0 { - vmmc-supply = <®_vcc_io>; - bus-width = <4>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ - status = "okay"; -}; - -&ohci0 { - status = "okay"; -}; - -&ohci1 { - status = "okay"; -}; - -&ohci2 { - status = "okay"; -}; - -&ohci3 { - status = "okay"; -}; - -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_a>; - status = "okay"; -}; - -&usb_otg { - dr_mode = "host"; - status = "okay"; -}; - -&usbphy { - /* VBUS on USB ports are always on */ - usb0_vbus-supply = <®_vcc5v0>; - usb1_vbus-supply = <®_vcc5v0>; - usb2_vbus-supply = <®_vcc5v0>; - usb3_vbus-supply = <®_vcc5v0>; - status = "okay"; }; diff --git a/arch/arm/boot/dts/sunxi-libretech-all-h3-cc.dtsi b/arch/arm/boot/dts/sunxi-libretech-all-h3-cc.dtsi new file mode 100644 index 0000000..d3a190b --- /dev/null +++ b/arch/arm/boot/dts/sunxi-libretech-all-h3-cc.dtsi @@ -0,0 +1,215 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org> + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + aliases { + ethernet0 = &emac; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + + pwr_led { + label = "librecomputer:green:pwr"; + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */ + default-state = "on"; + }; + + status_led { + label = "librecomputer:blue:status"; + gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */ + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + + power { + label = "power"; + linux,code = <KEY_POWER>; + gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */ + }; + }; + + reg_vcc1v2: vcc1v2 { + compatible = "regulator-fixed"; + regulator-name = "vcc1v2"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <®_vcc5v0>; + gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ + enable-active-high; + }; + + reg_vcc3v3: vcc3v3 { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <®_vcc5v0>; + }; + + /* This represents the board's 5V input */ + reg_vcc5v0: vcc5v0 { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + reg_vcc_dram: vcc-dram { + compatible = "regulator-fixed"; + regulator-name = "vcc-dram"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <®_vcc5v0>; + gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */ + enable-active-high; + }; + + reg_vcc_io: vcc-io { + compatible = "regulator-fixed"; + regulator-name = "vcc-io"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <®_vcc3v3>; + gpio = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL5 */ + }; + + reg_vdd_cpux: vdd-cpux { + compatible = "regulator-fixed"; + regulator-name = "vdd-cpux"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <®_vcc5v0>; + gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ + enable-active-high; + }; +}; + +&codec { + allwinner,audio-routing = + "Line Out", "LINEOUT", + "MIC1", "Mic", + "Mic", "MBIAS"; + status = "okay"; +}; + +&cpu0 { + cpu-supply = <®_vdd_cpux>; +}; + +&de { + status = "okay"; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&ehci2 { + status = "okay"; +}; + +&ehci3 { + status = "okay"; +}; + +&emac { + phy-handle = <&int_mii_phy>; + phy-mode = "mii"; + allwinner,leds-active-low; + status = "okay"; +}; + +&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + +&ir { + pinctrl-names = "default"; + pinctrl-0 = <&ir_pins_a>; + status = "okay"; +}; + +&mmc0 { + vmmc-supply = <®_vcc_io>; + bus-width = <4>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&ohci2 { + status = "okay"; +}; + +&ohci3 { + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "host"; + status = "okay"; +}; + +&usbphy { + /* VBUS on USB ports are always on */ + usb0_vbus-supply = <®_vcc5v0>; + usb1_vbus-supply = <®_vcc5v0>; + usb2_vbus-supply = <®_vcc5v0>; + usb3_vbus-supply = <®_vcc5v0>; + status = "okay"; +}; -- 2.7.4
WARNING: multiple messages have this Message-ID (diff)
From: narmstrong@baylibre.com (Neil Armstrong) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH v2 1/2] arm: dts: sun8i: h3: libretech-all-h3-cc: Move board definition to common dtsi Date: Tue, 24 Apr 2018 13:47:13 +0200 [thread overview] Message-ID: <1524570434-17814-2-git-send-email-narmstrong@baylibre.com> (raw) In-Reply-To: <1524570434-17814-1-git-send-email-narmstrong@baylibre.com> Since the libretech-all-h3-cc can use either the H2+, H3 or H5, move the content of the dts file to a common dtsi file to be included by the H3 variant and in a following patch the H5 variant. By the way, update the SPDX licence tag position. Suggested-by: Corentin Labbe <clabbe@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> --- arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts | 213 +------------------- arch/arm/boot/dts/sunxi-libretech-all-h3-cc.dtsi | 215 +++++++++++++++++++++ 2 files changed, 217 insertions(+), 211 deletions(-) create mode 100644 arch/arm/boot/dts/sunxi-libretech-all-h3-cc.dtsi diff --git a/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts b/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts index 5971b8b..50f2fb3 100644 --- a/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts +++ b/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts @@ -1,222 +1,13 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) /* * Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org> - * - * SPDX-License-Identifier: (GPL-2.0+ OR MIT) */ /dts-v1/; #include "sun8i-h3.dtsi" - -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/input/input.h> +#include "sunxi-libretech-all-h3-cc.dtsi" / { model = "Libre Computer Board ALL-H3-CC H3"; compatible = "libretech,all-h3-cc-h3", "allwinner,sun8i-h3"; - - aliases { - ethernet0 = &emac; - serial0 = &uart0; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - connector { - compatible = "hdmi-connector"; - type = "a"; - - port { - hdmi_con_in: endpoint { - remote-endpoint = <&hdmi_out_con>; - }; - }; - }; - - leds { - compatible = "gpio-leds"; - - pwr_led { - label = "librecomputer:green:pwr"; - gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */ - default-state = "on"; - }; - - status_led { - label = "librecomputer:blue:status"; - gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */ - }; - }; - - gpio_keys { - compatible = "gpio-keys"; - - power { - label = "power"; - linux,code = <KEY_POWER>; - gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */ - }; - }; - - reg_vcc1v2: vcc1v2 { - compatible = "regulator-fixed"; - regulator-name = "vcc1v2"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-boot-on; - vin-supply = <®_vcc5v0>; - gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ - enable-active-high; - }; - - reg_vcc3v3: vcc3v3 { - compatible = "regulator-fixed"; - regulator-name = "vcc3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - vin-supply = <®_vcc5v0>; - }; - - /* This represents the board's 5V input */ - reg_vcc5v0: vcc5v0 { - compatible = "regulator-fixed"; - regulator-name = "vcc5v0"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - }; - - reg_vcc_dram: vcc-dram { - compatible = "regulator-fixed"; - regulator-name = "vcc-dram"; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1500000>; - regulator-always-on; - regulator-boot-on; - vin-supply = <®_vcc5v0>; - gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */ - enable-active-high; - }; - - reg_vcc_io: vcc-io { - compatible = "regulator-fixed"; - regulator-name = "vcc-io"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-boot-on; - vin-supply = <®_vcc3v3>; - gpio = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL5 */ - }; - - reg_vdd_cpux: vdd-cpux { - compatible = "regulator-fixed"; - regulator-name = "vdd-cpux"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - regulator-always-on; - regulator-boot-on; - vin-supply = <®_vcc5v0>; - gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ - enable-active-high; - }; -}; - -&codec { - allwinner,audio-routing = - "Line Out", "LINEOUT", - "MIC1", "Mic", - "Mic", "MBIAS"; - status = "okay"; -}; - -&cpu0 { - cpu-supply = <®_vdd_cpux>; -}; - -&de { - status = "okay"; -}; - -&ehci0 { - status = "okay"; -}; - -&ehci1 { - status = "okay"; -}; - -&ehci2 { - status = "okay"; -}; - -&ehci3 { - status = "okay"; -}; - -&emac { - phy-handle = <&int_mii_phy>; - phy-mode = "mii"; - allwinner,leds-active-low; - status = "okay"; -}; - -&hdmi { - status = "okay"; -}; - -&hdmi_out { - hdmi_out_con: endpoint { - remote-endpoint = <&hdmi_con_in>; - }; -}; - -&ir { - pinctrl-names = "default"; - pinctrl-0 = <&ir_pins_a>; - status = "okay"; -}; - -&mmc0 { - vmmc-supply = <®_vcc_io>; - bus-width = <4>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ - status = "okay"; -}; - -&ohci0 { - status = "okay"; -}; - -&ohci1 { - status = "okay"; -}; - -&ohci2 { - status = "okay"; -}; - -&ohci3 { - status = "okay"; -}; - -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_a>; - status = "okay"; -}; - -&usb_otg { - dr_mode = "host"; - status = "okay"; -}; - -&usbphy { - /* VBUS on USB ports are always on */ - usb0_vbus-supply = <®_vcc5v0>; - usb1_vbus-supply = <®_vcc5v0>; - usb2_vbus-supply = <®_vcc5v0>; - usb3_vbus-supply = <®_vcc5v0>; - status = "okay"; }; diff --git a/arch/arm/boot/dts/sunxi-libretech-all-h3-cc.dtsi b/arch/arm/boot/dts/sunxi-libretech-all-h3-cc.dtsi new file mode 100644 index 0000000..d3a190b --- /dev/null +++ b/arch/arm/boot/dts/sunxi-libretech-all-h3-cc.dtsi @@ -0,0 +1,215 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org> + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + aliases { + ethernet0 = &emac; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + + pwr_led { + label = "librecomputer:green:pwr"; + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */ + default-state = "on"; + }; + + status_led { + label = "librecomputer:blue:status"; + gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */ + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + + power { + label = "power"; + linux,code = <KEY_POWER>; + gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */ + }; + }; + + reg_vcc1v2: vcc1v2 { + compatible = "regulator-fixed"; + regulator-name = "vcc1v2"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <®_vcc5v0>; + gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ + enable-active-high; + }; + + reg_vcc3v3: vcc3v3 { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <®_vcc5v0>; + }; + + /* This represents the board's 5V input */ + reg_vcc5v0: vcc5v0 { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + reg_vcc_dram: vcc-dram { + compatible = "regulator-fixed"; + regulator-name = "vcc-dram"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <®_vcc5v0>; + gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */ + enable-active-high; + }; + + reg_vcc_io: vcc-io { + compatible = "regulator-fixed"; + regulator-name = "vcc-io"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <®_vcc3v3>; + gpio = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL5 */ + }; + + reg_vdd_cpux: vdd-cpux { + compatible = "regulator-fixed"; + regulator-name = "vdd-cpux"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <®_vcc5v0>; + gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ + enable-active-high; + }; +}; + +&codec { + allwinner,audio-routing = + "Line Out", "LINEOUT", + "MIC1", "Mic", + "Mic", "MBIAS"; + status = "okay"; +}; + +&cpu0 { + cpu-supply = <®_vdd_cpux>; +}; + +&de { + status = "okay"; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&ehci2 { + status = "okay"; +}; + +&ehci3 { + status = "okay"; +}; + +&emac { + phy-handle = <&int_mii_phy>; + phy-mode = "mii"; + allwinner,leds-active-low; + status = "okay"; +}; + +&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + +&ir { + pinctrl-names = "default"; + pinctrl-0 = <&ir_pins_a>; + status = "okay"; +}; + +&mmc0 { + vmmc-supply = <®_vcc_io>; + bus-width = <4>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&ohci2 { + status = "okay"; +}; + +&ohci3 { + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "host"; + status = "okay"; +}; + +&usbphy { + /* VBUS on USB ports are always on */ + usb0_vbus-supply = <®_vcc5v0>; + usb1_vbus-supply = <®_vcc5v0>; + usb2_vbus-supply = <®_vcc5v0>; + usb3_vbus-supply = <®_vcc5v0>; + status = "okay"; +}; -- 2.7.4
next prev parent reply other threads:[~2018-04-24 11:47 UTC|newest] Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top 2018-04-24 11:47 [PATCH v2 0/2] arm64: allwinner: Add support for Libre Computer Board ALL-H3-CC H5 ver Neil Armstrong 2018-04-24 11:47 ` Neil Armstrong 2018-04-24 11:47 ` Neil Armstrong [this message] 2018-04-24 11:47 ` [PATCH v2 1/2] arm: dts: sun8i: h3: libretech-all-h3-cc: Move board definition to common dtsi Neil Armstrong 2018-04-24 12:14 ` Maxime Ripard 2018-04-24 12:14 ` Maxime Ripard 2018-04-24 11:47 ` [PATCH v2 2/2] arm64: dts: allwinner: Add dts file for Libre Computer Board ALL-H3-CC H5 ver Neil Armstrong 2018-04-24 11:47 ` Neil Armstrong 2018-04-24 12:14 ` Maxime Ripard 2018-04-24 12:14 ` Maxime Ripard 2018-04-24 12:24 ` Chen-Yu Tsai 2018-04-24 12:24 ` Chen-Yu Tsai
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1524570434-17814-2-git-send-email-narmstrong@baylibre.com \ --to=narmstrong@baylibre.com \ --cc=clabbe@baylibre.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=maxime.ripard@bootlin.com \ --cc=wens@csie.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.