* [RFC PATCH v2 0/3] Add reset driver support for ZynqMP
@ 2018-09-05 6:40 ` Nava kishore Manne
0 siblings, 0 replies; 12+ messages in thread
From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw)
To: robh+dt, mark.rutland, michal.simek, p.zabel, nava.manne, rajanv,
jollys, devicetree, linux-arm-kernel, linux-kernel
This series of patches are created On top of the
below series of patches.
https://lkml.org/lkml/2018/8/3/687
Nava kishore Manne (3):
firmware: xilinx: Add reset API's
dt-bindings: fpga: Add bindings for ZynqMP reset driver
reset: reset-zynqmp: Adding support for Xilinx zynqmp reset
controller.
.../firmware/xilinx/xlnx,zynqmp-firmware.txt | 142 +++++++++++++++++++++
drivers/firmware/xilinx/zynqmp.c | 40 ++++++
drivers/reset/Makefile | 1 +
drivers/reset/reset-zynqmp.c | 115 +++++++++++++++++
include/linux/firmware/xlnx-zynqmp.h | 136 ++++++++++++++++++++
5 files changed, 434 insertions(+)
create mode 100644 drivers/reset/reset-zynqmp.c
--
2.7.4
^ permalink raw reply [flat|nested] 12+ messages in thread* [RFC PATCH v2 0/3] Add reset driver support for ZynqMP @ 2018-09-05 6:40 ` Nava kishore Manne 0 siblings, 0 replies; 12+ messages in thread From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw) To: linux-arm-kernel This series of patches are created On top of the below series of patches. https://lkml.org/lkml/2018/8/3/687 Nava kishore Manne (3): firmware: xilinx: Add reset API's dt-bindings: fpga: Add bindings for ZynqMP reset driver reset: reset-zynqmp: Adding support for Xilinx zynqmp reset controller. .../firmware/xilinx/xlnx,zynqmp-firmware.txt | 142 +++++++++++++++++++++ drivers/firmware/xilinx/zynqmp.c | 40 ++++++ drivers/reset/Makefile | 1 + drivers/reset/reset-zynqmp.c | 115 +++++++++++++++++ include/linux/firmware/xlnx-zynqmp.h | 136 ++++++++++++++++++++ 5 files changed, 434 insertions(+) create mode 100644 drivers/reset/reset-zynqmp.c -- 2.7.4 ^ permalink raw reply [flat|nested] 12+ messages in thread
* [RFC PATCH v2 0/3] Add reset driver support for ZynqMP @ 2018-09-05 6:40 ` Nava kishore Manne 0 siblings, 0 replies; 12+ messages in thread From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw) To: robh+dt, mark.rutland, michal.simek, p.zabel, nava.manne, rajanv, jollys, devicetree, linux-arm-kernel, linux-kernel This series of patches are created On top of the below series of patches. https://lkml.org/lkml/2018/8/3/687 Nava kishore Manne (3): firmware: xilinx: Add reset API's dt-bindings: fpga: Add bindings for ZynqMP reset driver reset: reset-zynqmp: Adding support for Xilinx zynqmp reset controller. .../firmware/xilinx/xlnx,zynqmp-firmware.txt | 142 +++++++++++++++++++++ drivers/firmware/xilinx/zynqmp.c | 40 ++++++ drivers/reset/Makefile | 1 + drivers/reset/reset-zynqmp.c | 115 +++++++++++++++++ include/linux/firmware/xlnx-zynqmp.h | 136 ++++++++++++++++++++ 5 files changed, 434 insertions(+) create mode 100644 drivers/reset/reset-zynqmp.c -- 2.7.4 ^ permalink raw reply [flat|nested] 12+ messages in thread
* [RFC PATCH v2 1/3] firmware: xilinx: Add reset API's 2018-09-05 6:40 ` Nava kishore Manne (?) @ 2018-09-05 6:40 ` Nava kishore Manne -1 siblings, 0 replies; 12+ messages in thread From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw) To: robh+dt, mark.rutland, michal.simek, p.zabel, nava.manne, rajanv, jollys, devicetree, linux-arm-kernel, linux-kernel This Patch Adds reset API's to support release, assert and status functionalities by using firmware interface. Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com> --- Changes for v2: -New Patch. drivers/firmware/xilinx/zynqmp.c | 40 +++++++++++ include/linux/firmware/xlnx-zynqmp.h | 136 +++++++++++++++++++++++++++++++++++ 2 files changed, 176 insertions(+) diff --git a/drivers/firmware/xilinx/zynqmp.c b/drivers/firmware/xilinx/zynqmp.c index 7ccedf0..639c72f 100644 --- a/drivers/firmware/xilinx/zynqmp.c +++ b/drivers/firmware/xilinx/zynqmp.c @@ -447,6 +447,44 @@ static int zynqmp_pm_clock_getparent(u32 clock_id, u32 *parent_id) return ret; } +/** + * zynqmp_pm_reset_assert - Request setting of reset (1 - assert, 0 - release) + * @reset: Reset to be configured + * @assert_flag: Flag stating should reset be asserted (1) or + * released (0) + * + * Return: Returns status, either success or error+reason + */ +static int zynqmp_pm_reset_assert(const enum zynqmp_pm_reset reset, + const enum zynqmp_pm_reset_action assert_flag) +{ + return zynqmp_pm_invoke_fn(PM_RESET_ASSERT, reset, assert_flag, + 0, 0, NULL); +} + +/** + * zynqmp_pm_reset_get_status - Get status of the reset + * @reset: Reset whose status should be returned + * @status: Returned status + * + * Return: Returns status, either success or error+reason + */ +static int zynqmp_pm_reset_get_status(const enum zynqmp_pm_reset reset, + u32 *status) +{ + u32 ret_payload[PAYLOAD_ARG_CNT]; + int ret; + + if (!status) + return -EINVAL; + + ret = zynqmp_pm_invoke_fn(PM_RESET_GET_STATUS, reset, 0, + 0, 0, ret_payload); + *status = ret_payload[1]; + + return ret; +} + static const struct zynqmp_eemi_ops eemi_ops = { .get_api_version = zynqmp_pm_get_api_version, .ioctl = zynqmp_pm_ioctl, @@ -460,6 +498,8 @@ static const struct zynqmp_eemi_ops eemi_ops = { .clock_getrate = zynqmp_pm_clock_getrate, .clock_setparent = zynqmp_pm_clock_setparent, .clock_getparent = zynqmp_pm_clock_getparent, + .reset_assert = zynqmp_pm_reset_assert, + .reset_get_status = zynqmp_pm_reset_get_status, }; /** diff --git a/include/linux/firmware/xlnx-zynqmp.h b/include/linux/firmware/xlnx-zynqmp.h index 58a7478..93decf5 100644 --- a/include/linux/firmware/xlnx-zynqmp.h +++ b/include/linux/firmware/xlnx-zynqmp.h @@ -34,6 +34,8 @@ enum pm_api_id { PM_GET_API_VERSION = 1, + PM_RESET_ASSERT = 17, + PM_RESET_GET_STATUS, PM_IOCTL = 34, PM_QUERY_DATA, PM_CLOCK_ENABLE, @@ -74,6 +76,137 @@ enum pm_query_id { PM_QID_CLOCK_GET_ATTRIBUTES, }; +enum zynqmp_pm_reset_action { + PM_RESET_ACTION_RELEASE, + PM_RESET_ACTION_ASSERT, + PM_RESET_ACTION_PULSE, +}; + +enum zynqmp_pm_reset { + ZYNQMP_PM_RESET_START = 999, + ZYNQMP_PM_RESET_PCIE_CFG, + ZYNQMP_PM_RESET_PCIE_BRIDGE, + ZYNQMP_PM_RESET_PCIE_CTRL, + ZYNQMP_PM_RESET_DP, + ZYNQMP_PM_RESET_SWDT_CRF, + ZYNQMP_PM_RESET_AFI_FM5, + ZYNQMP_PM_RESET_AFI_FM4, + ZYNQMP_PM_RESET_AFI_FM3, + ZYNQMP_PM_RESET_AFI_FM2, + ZYNQMP_PM_RESET_AFI_FM1, + ZYNQMP_PM_RESET_AFI_FM0, + ZYNQMP_PM_RESET_GDMA, + ZYNQMP_PM_RESET_GPU_PP1, + ZYNQMP_PM_RESET_GPU_PP0, + ZYNQMP_PM_RESET_GPU, + ZYNQMP_PM_RESET_GT, + ZYNQMP_PM_RESET_SATA, + ZYNQMP_PM_RESET_ACPU3_PWRON, + ZYNQMP_PM_RESET_ACPU2_PWRON, + ZYNQMP_PM_RESET_ACPU1_PWRON, + ZYNQMP_PM_RESET_ACPU0_PWRON, + ZYNQMP_PM_RESET_APU_L2, + ZYNQMP_PM_RESET_ACPU3, + ZYNQMP_PM_RESET_ACPU2, + ZYNQMP_PM_RESET_ACPU1, + ZYNQMP_PM_RESET_ACPU0, + ZYNQMP_PM_RESET_DDR, + ZYNQMP_PM_RESET_APM_FPD, + ZYNQMP_PM_RESET_SOFT, + ZYNQMP_PM_RESET_GEM0, + ZYNQMP_PM_RESET_GEM1, + ZYNQMP_PM_RESET_GEM2, + ZYNQMP_PM_RESET_GEM3, + ZYNQMP_PM_RESET_QSPI, + ZYNQMP_PM_RESET_UART0, + ZYNQMP_PM_RESET_UART1, + ZYNQMP_PM_RESET_SPI0, + ZYNQMP_PM_RESET_SPI1, + ZYNQMP_PM_RESET_SDIO0, + ZYNQMP_PM_RESET_SDIO1, + ZYNQMP_PM_RESET_CAN0, + ZYNQMP_PM_RESET_CAN1, + ZYNQMP_PM_RESET_I2C0, + ZYNQMP_PM_RESET_I2C1, + ZYNQMP_PM_RESET_TTC0, + ZYNQMP_PM_RESET_TTC1, + ZYNQMP_PM_RESET_TTC2, + ZYNQMP_PM_RESET_TTC3, + ZYNQMP_PM_RESET_SWDT_CRL, + ZYNQMP_PM_RESET_NAND, + ZYNQMP_PM_RESET_ADMA, + ZYNQMP_PM_RESET_GPIO, + ZYNQMP_PM_RESET_IOU_CC, + ZYNQMP_PM_RESET_TIMESTAMP, + ZYNQMP_PM_RESET_RPU_R50, + ZYNQMP_PM_RESET_RPU_R51, + ZYNQMP_PM_RESET_RPU_AMBA, + ZYNQMP_PM_RESET_OCM, + ZYNQMP_PM_RESET_RPU_PGE, + ZYNQMP_PM_RESET_USB0_CORERESET, + ZYNQMP_PM_RESET_USB1_CORERESET, + ZYNQMP_PM_RESET_USB0_HIBERRESET, + ZYNQMP_PM_RESET_USB1_HIBERRESET, + ZYNQMP_PM_RESET_USB0_APB, + ZYNQMP_PM_RESET_USB1_APB, + ZYNQMP_PM_RESET_IPI, + ZYNQMP_PM_RESET_APM_LPD, + ZYNQMP_PM_RESET_RTC, + ZYNQMP_PM_RESET_SYSMON, + ZYNQMP_PM_RESET_AFI_FM6, + ZYNQMP_PM_RESET_LPD_SWDT, + ZYNQMP_PM_RESET_FPD, + ZYNQMP_PM_RESET_RPU_DBG1, + ZYNQMP_PM_RESET_RPU_DBG0, + ZYNQMP_PM_RESET_DBG_LPD, + ZYNQMP_PM_RESET_DBG_FPD, + ZYNQMP_PM_RESET_APLL, + ZYNQMP_PM_RESET_DPLL, + ZYNQMP_PM_RESET_VPLL, + ZYNQMP_PM_RESET_IOPLL, + ZYNQMP_PM_RESET_RPLL, + ZYNQMP_PM_RESET_GPO3_PL_0, + ZYNQMP_PM_RESET_GPO3_PL_1, + ZYNQMP_PM_RESET_GPO3_PL_2, + ZYNQMP_PM_RESET_GPO3_PL_3, + ZYNQMP_PM_RESET_GPO3_PL_4, + ZYNQMP_PM_RESET_GPO3_PL_5, + ZYNQMP_PM_RESET_GPO3_PL_6, + ZYNQMP_PM_RESET_GPO3_PL_7, + ZYNQMP_PM_RESET_GPO3_PL_8, + ZYNQMP_PM_RESET_GPO3_PL_9, + ZYNQMP_PM_RESET_GPO3_PL_10, + ZYNQMP_PM_RESET_GPO3_PL_11, + ZYNQMP_PM_RESET_GPO3_PL_12, + ZYNQMP_PM_RESET_GPO3_PL_13, + ZYNQMP_PM_RESET_GPO3_PL_14, + ZYNQMP_PM_RESET_GPO3_PL_15, + ZYNQMP_PM_RESET_GPO3_PL_16, + ZYNQMP_PM_RESET_GPO3_PL_17, + ZYNQMP_PM_RESET_GPO3_PL_18, + ZYNQMP_PM_RESET_GPO3_PL_19, + ZNQMP_PM_RESET_GPO3_PL_20, + ZYNQMP_PM_RESET_GPO3_PL_21, + ZYNQMP_PM_RESET_GPO3_PL_22, + ZYNQMP_PM_RESET_GPO3_PL_23, + ZYNQMP_PM_RESET_GPO3_PL_24, + ZYNQMP_PM_RESET_GPO3_PL_25, + ZYNQMP_PM_RESET_GPO3_PL_26, + ZYNQMP_PM_RESET_GPO3_PL_27, + ZYNQMP_PM_RESET_GPO3_PL_28, + ZYNQMP_PM_RESET_GPO3_PL_29, + ZYNQMP_PM_RESET_GPO3_PL_30, + ZYNQMP_PM_RESET_GPO3_PL_31, + ZYNQMP_PM_RESET_RPU_LS, + ZYNQMP_PM_RESET_PS_ONLY, + ZYNQMP_PM_RESET_PL, + ZYNQMP_PM_RESET_PS_PL0, + ZYNQMP_PM_RESET_PS_PL1, + ZYNQMP_PM_RESET_PS_PL2, + ZYNQMP_PM_RESET_PS_PL3, + ZYNQMP_PM_RESET_END +}; + /** * struct zynqmp_pm_query_data - PM query data * @qid: query ID @@ -101,6 +234,9 @@ struct zynqmp_eemi_ops { int (*clock_getrate)(u32 clock_id, u64 *rate); int (*clock_setparent)(u32 clock_id, u32 parent_id); int (*clock_getparent)(u32 clock_id, u32 *parent_id); + int (*reset_assert)(const enum zynqmp_pm_reset reset, + const enum zynqmp_pm_reset_action assert_flag); + int (*reset_get_status)(const enum zynqmp_pm_reset reset, u32 *status); }; #if IS_REACHABLE(CONFIG_ARCH_ZYNQMP) -- 2.7.4 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RFC PATCH v2 1/3] firmware: xilinx: Add reset API's @ 2018-09-05 6:40 ` Nava kishore Manne 0 siblings, 0 replies; 12+ messages in thread From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw) To: linux-arm-kernel This Patch Adds reset API's to support release, assert and status functionalities by using firmware interface. Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com> --- Changes for v2: -New Patch. drivers/firmware/xilinx/zynqmp.c | 40 +++++++++++ include/linux/firmware/xlnx-zynqmp.h | 136 +++++++++++++++++++++++++++++++++++ 2 files changed, 176 insertions(+) diff --git a/drivers/firmware/xilinx/zynqmp.c b/drivers/firmware/xilinx/zynqmp.c index 7ccedf0..639c72f 100644 --- a/drivers/firmware/xilinx/zynqmp.c +++ b/drivers/firmware/xilinx/zynqmp.c @@ -447,6 +447,44 @@ static int zynqmp_pm_clock_getparent(u32 clock_id, u32 *parent_id) return ret; } +/** + * zynqmp_pm_reset_assert - Request setting of reset (1 - assert, 0 - release) + * @reset: Reset to be configured + * @assert_flag: Flag stating should reset be asserted (1) or + * released (0) + * + * Return: Returns status, either success or error+reason + */ +static int zynqmp_pm_reset_assert(const enum zynqmp_pm_reset reset, + const enum zynqmp_pm_reset_action assert_flag) +{ + return zynqmp_pm_invoke_fn(PM_RESET_ASSERT, reset, assert_flag, + 0, 0, NULL); +} + +/** + * zynqmp_pm_reset_get_status - Get status of the reset + * @reset: Reset whose status should be returned + * @status: Returned status + * + * Return: Returns status, either success or error+reason + */ +static int zynqmp_pm_reset_get_status(const enum zynqmp_pm_reset reset, + u32 *status) +{ + u32 ret_payload[PAYLOAD_ARG_CNT]; + int ret; + + if (!status) + return -EINVAL; + + ret = zynqmp_pm_invoke_fn(PM_RESET_GET_STATUS, reset, 0, + 0, 0, ret_payload); + *status = ret_payload[1]; + + return ret; +} + static const struct zynqmp_eemi_ops eemi_ops = { .get_api_version = zynqmp_pm_get_api_version, .ioctl = zynqmp_pm_ioctl, @@ -460,6 +498,8 @@ static const struct zynqmp_eemi_ops eemi_ops = { .clock_getrate = zynqmp_pm_clock_getrate, .clock_setparent = zynqmp_pm_clock_setparent, .clock_getparent = zynqmp_pm_clock_getparent, + .reset_assert = zynqmp_pm_reset_assert, + .reset_get_status = zynqmp_pm_reset_get_status, }; /** diff --git a/include/linux/firmware/xlnx-zynqmp.h b/include/linux/firmware/xlnx-zynqmp.h index 58a7478..93decf5 100644 --- a/include/linux/firmware/xlnx-zynqmp.h +++ b/include/linux/firmware/xlnx-zynqmp.h @@ -34,6 +34,8 @@ enum pm_api_id { PM_GET_API_VERSION = 1, + PM_RESET_ASSERT = 17, + PM_RESET_GET_STATUS, PM_IOCTL = 34, PM_QUERY_DATA, PM_CLOCK_ENABLE, @@ -74,6 +76,137 @@ enum pm_query_id { PM_QID_CLOCK_GET_ATTRIBUTES, }; +enum zynqmp_pm_reset_action { + PM_RESET_ACTION_RELEASE, + PM_RESET_ACTION_ASSERT, + PM_RESET_ACTION_PULSE, +}; + +enum zynqmp_pm_reset { + ZYNQMP_PM_RESET_START = 999, + ZYNQMP_PM_RESET_PCIE_CFG, + ZYNQMP_PM_RESET_PCIE_BRIDGE, + ZYNQMP_PM_RESET_PCIE_CTRL, + ZYNQMP_PM_RESET_DP, + ZYNQMP_PM_RESET_SWDT_CRF, + ZYNQMP_PM_RESET_AFI_FM5, + ZYNQMP_PM_RESET_AFI_FM4, + ZYNQMP_PM_RESET_AFI_FM3, + ZYNQMP_PM_RESET_AFI_FM2, + ZYNQMP_PM_RESET_AFI_FM1, + ZYNQMP_PM_RESET_AFI_FM0, + ZYNQMP_PM_RESET_GDMA, + ZYNQMP_PM_RESET_GPU_PP1, + ZYNQMP_PM_RESET_GPU_PP0, + ZYNQMP_PM_RESET_GPU, + ZYNQMP_PM_RESET_GT, + ZYNQMP_PM_RESET_SATA, + ZYNQMP_PM_RESET_ACPU3_PWRON, + ZYNQMP_PM_RESET_ACPU2_PWRON, + ZYNQMP_PM_RESET_ACPU1_PWRON, + ZYNQMP_PM_RESET_ACPU0_PWRON, + ZYNQMP_PM_RESET_APU_L2, + ZYNQMP_PM_RESET_ACPU3, + ZYNQMP_PM_RESET_ACPU2, + ZYNQMP_PM_RESET_ACPU1, + ZYNQMP_PM_RESET_ACPU0, + ZYNQMP_PM_RESET_DDR, + ZYNQMP_PM_RESET_APM_FPD, + ZYNQMP_PM_RESET_SOFT, + ZYNQMP_PM_RESET_GEM0, + ZYNQMP_PM_RESET_GEM1, + ZYNQMP_PM_RESET_GEM2, + ZYNQMP_PM_RESET_GEM3, + ZYNQMP_PM_RESET_QSPI, + ZYNQMP_PM_RESET_UART0, + ZYNQMP_PM_RESET_UART1, + ZYNQMP_PM_RESET_SPI0, + ZYNQMP_PM_RESET_SPI1, + ZYNQMP_PM_RESET_SDIO0, + ZYNQMP_PM_RESET_SDIO1, + ZYNQMP_PM_RESET_CAN0, + ZYNQMP_PM_RESET_CAN1, + ZYNQMP_PM_RESET_I2C0, + ZYNQMP_PM_RESET_I2C1, + ZYNQMP_PM_RESET_TTC0, + ZYNQMP_PM_RESET_TTC1, + ZYNQMP_PM_RESET_TTC2, + ZYNQMP_PM_RESET_TTC3, + ZYNQMP_PM_RESET_SWDT_CRL, + ZYNQMP_PM_RESET_NAND, + ZYNQMP_PM_RESET_ADMA, + ZYNQMP_PM_RESET_GPIO, + ZYNQMP_PM_RESET_IOU_CC, + ZYNQMP_PM_RESET_TIMESTAMP, + ZYNQMP_PM_RESET_RPU_R50, + ZYNQMP_PM_RESET_RPU_R51, + ZYNQMP_PM_RESET_RPU_AMBA, + ZYNQMP_PM_RESET_OCM, + ZYNQMP_PM_RESET_RPU_PGE, + ZYNQMP_PM_RESET_USB0_CORERESET, + ZYNQMP_PM_RESET_USB1_CORERESET, + ZYNQMP_PM_RESET_USB0_HIBERRESET, + ZYNQMP_PM_RESET_USB1_HIBERRESET, + ZYNQMP_PM_RESET_USB0_APB, + ZYNQMP_PM_RESET_USB1_APB, + ZYNQMP_PM_RESET_IPI, + ZYNQMP_PM_RESET_APM_LPD, + ZYNQMP_PM_RESET_RTC, + ZYNQMP_PM_RESET_SYSMON, + ZYNQMP_PM_RESET_AFI_FM6, + ZYNQMP_PM_RESET_LPD_SWDT, + ZYNQMP_PM_RESET_FPD, + ZYNQMP_PM_RESET_RPU_DBG1, + ZYNQMP_PM_RESET_RPU_DBG0, + ZYNQMP_PM_RESET_DBG_LPD, + ZYNQMP_PM_RESET_DBG_FPD, + ZYNQMP_PM_RESET_APLL, + ZYNQMP_PM_RESET_DPLL, + ZYNQMP_PM_RESET_VPLL, + ZYNQMP_PM_RESET_IOPLL, + ZYNQMP_PM_RESET_RPLL, + ZYNQMP_PM_RESET_GPO3_PL_0, + ZYNQMP_PM_RESET_GPO3_PL_1, + ZYNQMP_PM_RESET_GPO3_PL_2, + ZYNQMP_PM_RESET_GPO3_PL_3, + ZYNQMP_PM_RESET_GPO3_PL_4, + ZYNQMP_PM_RESET_GPO3_PL_5, + ZYNQMP_PM_RESET_GPO3_PL_6, + ZYNQMP_PM_RESET_GPO3_PL_7, + ZYNQMP_PM_RESET_GPO3_PL_8, + ZYNQMP_PM_RESET_GPO3_PL_9, + ZYNQMP_PM_RESET_GPO3_PL_10, + ZYNQMP_PM_RESET_GPO3_PL_11, + ZYNQMP_PM_RESET_GPO3_PL_12, + ZYNQMP_PM_RESET_GPO3_PL_13, + ZYNQMP_PM_RESET_GPO3_PL_14, + ZYNQMP_PM_RESET_GPO3_PL_15, + ZYNQMP_PM_RESET_GPO3_PL_16, + ZYNQMP_PM_RESET_GPO3_PL_17, + ZYNQMP_PM_RESET_GPO3_PL_18, + ZYNQMP_PM_RESET_GPO3_PL_19, + ZNQMP_PM_RESET_GPO3_PL_20, + ZYNQMP_PM_RESET_GPO3_PL_21, + ZYNQMP_PM_RESET_GPO3_PL_22, + ZYNQMP_PM_RESET_GPO3_PL_23, + ZYNQMP_PM_RESET_GPO3_PL_24, + ZYNQMP_PM_RESET_GPO3_PL_25, + ZYNQMP_PM_RESET_GPO3_PL_26, + ZYNQMP_PM_RESET_GPO3_PL_27, + ZYNQMP_PM_RESET_GPO3_PL_28, + ZYNQMP_PM_RESET_GPO3_PL_29, + ZYNQMP_PM_RESET_GPO3_PL_30, + ZYNQMP_PM_RESET_GPO3_PL_31, + ZYNQMP_PM_RESET_RPU_LS, + ZYNQMP_PM_RESET_PS_ONLY, + ZYNQMP_PM_RESET_PL, + ZYNQMP_PM_RESET_PS_PL0, + ZYNQMP_PM_RESET_PS_PL1, + ZYNQMP_PM_RESET_PS_PL2, + ZYNQMP_PM_RESET_PS_PL3, + ZYNQMP_PM_RESET_END +}; + /** * struct zynqmp_pm_query_data - PM query data * @qid: query ID @@ -101,6 +234,9 @@ struct zynqmp_eemi_ops { int (*clock_getrate)(u32 clock_id, u64 *rate); int (*clock_setparent)(u32 clock_id, u32 parent_id); int (*clock_getparent)(u32 clock_id, u32 *parent_id); + int (*reset_assert)(const enum zynqmp_pm_reset reset, + const enum zynqmp_pm_reset_action assert_flag); + int (*reset_get_status)(const enum zynqmp_pm_reset reset, u32 *status); }; #if IS_REACHABLE(CONFIG_ARCH_ZYNQMP) -- 2.7.4 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RFC PATCH v2 1/3] firmware: xilinx: Add reset API's @ 2018-09-05 6:40 ` Nava kishore Manne 0 siblings, 0 replies; 12+ messages in thread From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw) To: robh+dt, mark.rutland, michal.simek, p.zabel, nava.manne, rajanv, jollys, devicetree, linux-arm-kernel, linux-kernel This Patch Adds reset API's to support release, assert and status functionalities by using firmware interface. Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com> --- Changes for v2: -New Patch. drivers/firmware/xilinx/zynqmp.c | 40 +++++++++++ include/linux/firmware/xlnx-zynqmp.h | 136 +++++++++++++++++++++++++++++++++++ 2 files changed, 176 insertions(+) diff --git a/drivers/firmware/xilinx/zynqmp.c b/drivers/firmware/xilinx/zynqmp.c index 7ccedf0..639c72f 100644 --- a/drivers/firmware/xilinx/zynqmp.c +++ b/drivers/firmware/xilinx/zynqmp.c @@ -447,6 +447,44 @@ static int zynqmp_pm_clock_getparent(u32 clock_id, u32 *parent_id) return ret; } +/** + * zynqmp_pm_reset_assert - Request setting of reset (1 - assert, 0 - release) + * @reset: Reset to be configured + * @assert_flag: Flag stating should reset be asserted (1) or + * released (0) + * + * Return: Returns status, either success or error+reason + */ +static int zynqmp_pm_reset_assert(const enum zynqmp_pm_reset reset, + const enum zynqmp_pm_reset_action assert_flag) +{ + return zynqmp_pm_invoke_fn(PM_RESET_ASSERT, reset, assert_flag, + 0, 0, NULL); +} + +/** + * zynqmp_pm_reset_get_status - Get status of the reset + * @reset: Reset whose status should be returned + * @status: Returned status + * + * Return: Returns status, either success or error+reason + */ +static int zynqmp_pm_reset_get_status(const enum zynqmp_pm_reset reset, + u32 *status) +{ + u32 ret_payload[PAYLOAD_ARG_CNT]; + int ret; + + if (!status) + return -EINVAL; + + ret = zynqmp_pm_invoke_fn(PM_RESET_GET_STATUS, reset, 0, + 0, 0, ret_payload); + *status = ret_payload[1]; + + return ret; +} + static const struct zynqmp_eemi_ops eemi_ops = { .get_api_version = zynqmp_pm_get_api_version, .ioctl = zynqmp_pm_ioctl, @@ -460,6 +498,8 @@ static const struct zynqmp_eemi_ops eemi_ops = { .clock_getrate = zynqmp_pm_clock_getrate, .clock_setparent = zynqmp_pm_clock_setparent, .clock_getparent = zynqmp_pm_clock_getparent, + .reset_assert = zynqmp_pm_reset_assert, + .reset_get_status = zynqmp_pm_reset_get_status, }; /** diff --git a/include/linux/firmware/xlnx-zynqmp.h b/include/linux/firmware/xlnx-zynqmp.h index 58a7478..93decf5 100644 --- a/include/linux/firmware/xlnx-zynqmp.h +++ b/include/linux/firmware/xlnx-zynqmp.h @@ -34,6 +34,8 @@ enum pm_api_id { PM_GET_API_VERSION = 1, + PM_RESET_ASSERT = 17, + PM_RESET_GET_STATUS, PM_IOCTL = 34, PM_QUERY_DATA, PM_CLOCK_ENABLE, @@ -74,6 +76,137 @@ enum pm_query_id { PM_QID_CLOCK_GET_ATTRIBUTES, }; +enum zynqmp_pm_reset_action { + PM_RESET_ACTION_RELEASE, + PM_RESET_ACTION_ASSERT, + PM_RESET_ACTION_PULSE, +}; + +enum zynqmp_pm_reset { + ZYNQMP_PM_RESET_START = 999, + ZYNQMP_PM_RESET_PCIE_CFG, + ZYNQMP_PM_RESET_PCIE_BRIDGE, + ZYNQMP_PM_RESET_PCIE_CTRL, + ZYNQMP_PM_RESET_DP, + ZYNQMP_PM_RESET_SWDT_CRF, + ZYNQMP_PM_RESET_AFI_FM5, + ZYNQMP_PM_RESET_AFI_FM4, + ZYNQMP_PM_RESET_AFI_FM3, + ZYNQMP_PM_RESET_AFI_FM2, + ZYNQMP_PM_RESET_AFI_FM1, + ZYNQMP_PM_RESET_AFI_FM0, + ZYNQMP_PM_RESET_GDMA, + ZYNQMP_PM_RESET_GPU_PP1, + ZYNQMP_PM_RESET_GPU_PP0, + ZYNQMP_PM_RESET_GPU, + ZYNQMP_PM_RESET_GT, + ZYNQMP_PM_RESET_SATA, + ZYNQMP_PM_RESET_ACPU3_PWRON, + ZYNQMP_PM_RESET_ACPU2_PWRON, + ZYNQMP_PM_RESET_ACPU1_PWRON, + ZYNQMP_PM_RESET_ACPU0_PWRON, + ZYNQMP_PM_RESET_APU_L2, + ZYNQMP_PM_RESET_ACPU3, + ZYNQMP_PM_RESET_ACPU2, + ZYNQMP_PM_RESET_ACPU1, + ZYNQMP_PM_RESET_ACPU0, + ZYNQMP_PM_RESET_DDR, + ZYNQMP_PM_RESET_APM_FPD, + ZYNQMP_PM_RESET_SOFT, + ZYNQMP_PM_RESET_GEM0, + ZYNQMP_PM_RESET_GEM1, + ZYNQMP_PM_RESET_GEM2, + ZYNQMP_PM_RESET_GEM3, + ZYNQMP_PM_RESET_QSPI, + ZYNQMP_PM_RESET_UART0, + ZYNQMP_PM_RESET_UART1, + ZYNQMP_PM_RESET_SPI0, + ZYNQMP_PM_RESET_SPI1, + ZYNQMP_PM_RESET_SDIO0, + ZYNQMP_PM_RESET_SDIO1, + ZYNQMP_PM_RESET_CAN0, + ZYNQMP_PM_RESET_CAN1, + ZYNQMP_PM_RESET_I2C0, + ZYNQMP_PM_RESET_I2C1, + ZYNQMP_PM_RESET_TTC0, + ZYNQMP_PM_RESET_TTC1, + ZYNQMP_PM_RESET_TTC2, + ZYNQMP_PM_RESET_TTC3, + ZYNQMP_PM_RESET_SWDT_CRL, + ZYNQMP_PM_RESET_NAND, + ZYNQMP_PM_RESET_ADMA, + ZYNQMP_PM_RESET_GPIO, + ZYNQMP_PM_RESET_IOU_CC, + ZYNQMP_PM_RESET_TIMESTAMP, + ZYNQMP_PM_RESET_RPU_R50, + ZYNQMP_PM_RESET_RPU_R51, + ZYNQMP_PM_RESET_RPU_AMBA, + ZYNQMP_PM_RESET_OCM, + ZYNQMP_PM_RESET_RPU_PGE, + ZYNQMP_PM_RESET_USB0_CORERESET, + ZYNQMP_PM_RESET_USB1_CORERESET, + ZYNQMP_PM_RESET_USB0_HIBERRESET, + ZYNQMP_PM_RESET_USB1_HIBERRESET, + ZYNQMP_PM_RESET_USB0_APB, + ZYNQMP_PM_RESET_USB1_APB, + ZYNQMP_PM_RESET_IPI, + ZYNQMP_PM_RESET_APM_LPD, + ZYNQMP_PM_RESET_RTC, + ZYNQMP_PM_RESET_SYSMON, + ZYNQMP_PM_RESET_AFI_FM6, + ZYNQMP_PM_RESET_LPD_SWDT, + ZYNQMP_PM_RESET_FPD, + ZYNQMP_PM_RESET_RPU_DBG1, + ZYNQMP_PM_RESET_RPU_DBG0, + ZYNQMP_PM_RESET_DBG_LPD, + ZYNQMP_PM_RESET_DBG_FPD, + ZYNQMP_PM_RESET_APLL, + ZYNQMP_PM_RESET_DPLL, + ZYNQMP_PM_RESET_VPLL, + ZYNQMP_PM_RESET_IOPLL, + ZYNQMP_PM_RESET_RPLL, + ZYNQMP_PM_RESET_GPO3_PL_0, + ZYNQMP_PM_RESET_GPO3_PL_1, + ZYNQMP_PM_RESET_GPO3_PL_2, + ZYNQMP_PM_RESET_GPO3_PL_3, + ZYNQMP_PM_RESET_GPO3_PL_4, + ZYNQMP_PM_RESET_GPO3_PL_5, + ZYNQMP_PM_RESET_GPO3_PL_6, + ZYNQMP_PM_RESET_GPO3_PL_7, + ZYNQMP_PM_RESET_GPO3_PL_8, + ZYNQMP_PM_RESET_GPO3_PL_9, + ZYNQMP_PM_RESET_GPO3_PL_10, + ZYNQMP_PM_RESET_GPO3_PL_11, + ZYNQMP_PM_RESET_GPO3_PL_12, + ZYNQMP_PM_RESET_GPO3_PL_13, + ZYNQMP_PM_RESET_GPO3_PL_14, + ZYNQMP_PM_RESET_GPO3_PL_15, + ZYNQMP_PM_RESET_GPO3_PL_16, + ZYNQMP_PM_RESET_GPO3_PL_17, + ZYNQMP_PM_RESET_GPO3_PL_18, + ZYNQMP_PM_RESET_GPO3_PL_19, + ZNQMP_PM_RESET_GPO3_PL_20, + ZYNQMP_PM_RESET_GPO3_PL_21, + ZYNQMP_PM_RESET_GPO3_PL_22, + ZYNQMP_PM_RESET_GPO3_PL_23, + ZYNQMP_PM_RESET_GPO3_PL_24, + ZYNQMP_PM_RESET_GPO3_PL_25, + ZYNQMP_PM_RESET_GPO3_PL_26, + ZYNQMP_PM_RESET_GPO3_PL_27, + ZYNQMP_PM_RESET_GPO3_PL_28, + ZYNQMP_PM_RESET_GPO3_PL_29, + ZYNQMP_PM_RESET_GPO3_PL_30, + ZYNQMP_PM_RESET_GPO3_PL_31, + ZYNQMP_PM_RESET_RPU_LS, + ZYNQMP_PM_RESET_PS_ONLY, + ZYNQMP_PM_RESET_PL, + ZYNQMP_PM_RESET_PS_PL0, + ZYNQMP_PM_RESET_PS_PL1, + ZYNQMP_PM_RESET_PS_PL2, + ZYNQMP_PM_RESET_PS_PL3, + ZYNQMP_PM_RESET_END +}; + /** * struct zynqmp_pm_query_data - PM query data * @qid: query ID @@ -101,6 +234,9 @@ struct zynqmp_eemi_ops { int (*clock_getrate)(u32 clock_id, u64 *rate); int (*clock_setparent)(u32 clock_id, u32 parent_id); int (*clock_getparent)(u32 clock_id, u32 *parent_id); + int (*reset_assert)(const enum zynqmp_pm_reset reset, + const enum zynqmp_pm_reset_action assert_flag); + int (*reset_get_status)(const enum zynqmp_pm_reset reset, u32 *status); }; #if IS_REACHABLE(CONFIG_ARCH_ZYNQMP) -- 2.7.4 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RFC PATCH v2 2/3] dt-bindings: fpga: Add bindings for ZynqMP reset driver 2018-09-05 6:40 ` Nava kishore Manne (?) @ 2018-09-05 6:40 ` Nava kishore Manne -1 siblings, 0 replies; 12+ messages in thread From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw) To: robh+dt, mark.rutland, michal.simek, p.zabel, nava.manne, rajanv, jollys, devicetree, linux-arm-kernel, linux-kernel Add documentation to describe Xilinx ZynqMP reset driver bindings. Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com> --- Changes for v2: -Moved reset node as a child to firwmare node. .../firmware/xilinx/xlnx,zynqmp-firmware.txt | 142 +++++++++++++++++++++ 1 file changed, 142 insertions(+) diff --git a/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt b/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt index 1b431d9..351b1bb 100644 --- a/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt +++ b/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt @@ -17,6 +17,144 @@ Required properties: - "smc" : SMC #0, following the SMCCC - "hvc" : HVC #0, following the SMCCC +-------------------------------------------------------------------------- + = Zynq UltraScale+ MPSoC reset driver binding = +-------------------------------------------------------------------------- +The Zynq UltraScale+ MPSoC has several different resets. + +See Chapter 36 of the Zynq UltraScale+ MPSoC TRM (UG) for more information +about zynqmp resets. + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Required Properties: +- compatible: "xlnx,zynqmp-reset" +- #reset-cells: Specifies the number of cells needed to encode reset + line, should be 1 + +Reset outputs: + 0 :PCIE config reset. + 1 :PCIE bridge block level reset (AXI interface). + 2 :PCIE control block level,reset. + 3 :Display Port block level reset (includes DPDMA). + 4 :FPD WDT reset. + 5 :AF_FM5 block level reset. + 6 :AF_FM4 block level reset. + 7 :AF_FM3 block level reset. + 8 :AF_FM2 block level reset. + 9 :AF_FM1 block level reset. + 10 :AF_FM0 block level reset. + 11 :GDMA block level reset. + 12 :Pixel Processor (GPU_PP1) block level reset. + 13 :Pixel Processor (GPU_PP0) block level reset. + 14 :GPU block level reset. + 15 :GT block level reset. + 16 :Sata block level reset. + 17 :ACPU3 power on reset. + 18 :ACPU2 power on reset. + 19 :ACPU1 power on reset. + 20 :ACPU0 power on reset. + 21 :APU L2 reset. + 22 :ACPU3 reset. + 23 :ACPU2 reset. + 24 :ACPU1 reset. + 25 :ACPU0 reset. + 26 :DDR block level reset inside of the DDR Sub System. + 27 :APM block level reset inside of the DDR Sub System. + 28 :soft reset. + 29 :GEM 0 reset. + 30 :GEM 1 reset. + 31 :GEM 2 reset. + 32 :GEM 3 reset. + 33 :qspi reset. + 34 :uart0 reset. + 35 :uart1 reset. + 36 :spi0 reset. + 37 :spi1 reset. + 38 :sdio0 reset. + 39 :sdio1 reset. + 40 :can0 reset. + 41 :can1 reset. + 42 :i2c0 reset. + 43 :i2c1 reset. + 44 :ttc0 reset. + 45 :ttc1 reset. + 46 :ttc2 reset. + 47 :ttc3 reset. + 48 :swdt reset. + 49 :nand reset. + 50 :adma reset. + 51 :gpio reset. + 52 :iou_cc reset. + 53 :timestamp reset. + 54 :rpu_r50 reset. + 55 :rpu r51 reset. + 56 :rpu_amba reset. + 57 :ocm reset. + 58 :rpu_pge reset. + 59 :usb0_core reset. + 60 :usb1_core reset. + 61 :usb0_hiber reset. + 62 :usb1_hiber reset. + 63 :usb0_apb reset. + 64 :usb1_apb reset. + 65 :ipi reset. + 66 :apm reset. + 67 :rtc reset. + 68 :sysmon reset. + 69 :afi_fm6 reset. + 70 :lpd_swdt reset. + 71 :fpd_reset. + 72 :rpu_dbg1 reset. + 73 :rpu_dbg0 reset. + 74 :dbg_lpd reset. + 75 :dbg_fpd reset. + 76 :apll reset. + 77 :dpll reset. + 78 :vpll reset. + 79 :iopll reset. + 80 :rpll reset. + 81 :gpio_pl_0 reset. + 82 :gpio_pl_1 reset. + 83 :gpio_pl_2 reset. + 84 :gpio_pl_3 reset. + 85 :gpio_pl_4 reset. + 86 :gpio_pl_5 reset. + 87 :gpio_pl_6 reset. + 88 :gpio_pl_7 reset. + 89 :gpio_pl_8 reset. + 90 :gpio_pl_9 reset. + 91 :gpio_pl_10 reset. + 92 :gpio_pl_11 reset. + 93 :gpio_pl_12 reset. + 94 :gpio_pl_13 reset. + 95 :gpio_pl_14 reset. + 96 :gpio_pl_15 reset. + 97 :gpio_pl_16 reset. + 98 :gpio_pl_17 reset. + 99 :gpio_pl_18 reset. + 100 :gpio_pl_19 reset. + 101 :gpio_pl_20 reset. + 102 :gpio_pl_21 reset. + 103 :gpio_pl_22 reset. + 104 :gpio_pl_23 reset. + 105 :gpio_pl_24 reset. + 106 :gpio_pl_25 reset. + 107 :gpio_pl_26 reset. + 108 :gpio_pl_27 reset. + 109 :gpio_pl_28 reset. + 110 :gpio_pl_29 reset. + 111 :gpio_pl_30 reset. + 112 :gpio_pl_31 reset. + 113 :rpu_ls reset. + 114 :ps_only reset. + 115 :pl reset. + 116 :ps_pl0 reset + 117 :ps_pl1 reset + 118 :ps_pl2 reset + 119 :ps_pl3 reset + ------- Example ------- @@ -25,5 +163,9 @@ firmware { zynqmp_firmware: zynqmp-firmware { compatible = "xlnx,zynqmp-firmware"; method = "smc"; + reset-controller:reset-controller@0 { + compatible = "xlnx,zynqmp-reset"; + #reset-cells = <1>; + }; }; }; -- 2.7.4 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RFC PATCH v2 2/3] dt-bindings: fpga: Add bindings for ZynqMP reset driver @ 2018-09-05 6:40 ` Nava kishore Manne 0 siblings, 0 replies; 12+ messages in thread From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw) To: linux-arm-kernel Add documentation to describe Xilinx ZynqMP reset driver bindings. Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com> --- Changes for v2: -Moved reset node as a child to firwmare node. .../firmware/xilinx/xlnx,zynqmp-firmware.txt | 142 +++++++++++++++++++++ 1 file changed, 142 insertions(+) diff --git a/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt b/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt index 1b431d9..351b1bb 100644 --- a/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt +++ b/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt @@ -17,6 +17,144 @@ Required properties: - "smc" : SMC #0, following the SMCCC - "hvc" : HVC #0, following the SMCCC +-------------------------------------------------------------------------- + = Zynq UltraScale+ MPSoC reset driver binding = +-------------------------------------------------------------------------- +The Zynq UltraScale+ MPSoC has several different resets. + +See Chapter 36 of the Zynq UltraScale+ MPSoC TRM (UG) for more information +about zynqmp resets. + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Required Properties: +- compatible: "xlnx,zynqmp-reset" +- #reset-cells: Specifies the number of cells needed to encode reset + line, should be 1 + +Reset outputs: + 0 :PCIE config reset. + 1 :PCIE bridge block level reset (AXI interface). + 2 :PCIE control block level,reset. + 3 :Display Port block level reset (includes DPDMA). + 4 :FPD WDT reset. + 5 :AF_FM5 block level reset. + 6 :AF_FM4 block level reset. + 7 :AF_FM3 block level reset. + 8 :AF_FM2 block level reset. + 9 :AF_FM1 block level reset. + 10 :AF_FM0 block level reset. + 11 :GDMA block level reset. + 12 :Pixel Processor (GPU_PP1) block level reset. + 13 :Pixel Processor (GPU_PP0) block level reset. + 14 :GPU block level reset. + 15 :GT block level reset. + 16 :Sata block level reset. + 17 :ACPU3 power on reset. + 18 :ACPU2 power on reset. + 19 :ACPU1 power on reset. + 20 :ACPU0 power on reset. + 21 :APU L2 reset. + 22 :ACPU3 reset. + 23 :ACPU2 reset. + 24 :ACPU1 reset. + 25 :ACPU0 reset. + 26 :DDR block level reset inside of the DDR Sub System. + 27 :APM block level reset inside of the DDR Sub System. + 28 :soft reset. + 29 :GEM 0 reset. + 30 :GEM 1 reset. + 31 :GEM 2 reset. + 32 :GEM 3 reset. + 33 :qspi reset. + 34 :uart0 reset. + 35 :uart1 reset. + 36 :spi0 reset. + 37 :spi1 reset. + 38 :sdio0 reset. + 39 :sdio1 reset. + 40 :can0 reset. + 41 :can1 reset. + 42 :i2c0 reset. + 43 :i2c1 reset. + 44 :ttc0 reset. + 45 :ttc1 reset. + 46 :ttc2 reset. + 47 :ttc3 reset. + 48 :swdt reset. + 49 :nand reset. + 50 :adma reset. + 51 :gpio reset. + 52 :iou_cc reset. + 53 :timestamp reset. + 54 :rpu_r50 reset. + 55 :rpu r51 reset. + 56 :rpu_amba reset. + 57 :ocm reset. + 58 :rpu_pge reset. + 59 :usb0_core reset. + 60 :usb1_core reset. + 61 :usb0_hiber reset. + 62 :usb1_hiber reset. + 63 :usb0_apb reset. + 64 :usb1_apb reset. + 65 :ipi reset. + 66 :apm reset. + 67 :rtc reset. + 68 :sysmon reset. + 69 :afi_fm6 reset. + 70 :lpd_swdt reset. + 71 :fpd_reset. + 72 :rpu_dbg1 reset. + 73 :rpu_dbg0 reset. + 74 :dbg_lpd reset. + 75 :dbg_fpd reset. + 76 :apll reset. + 77 :dpll reset. + 78 :vpll reset. + 79 :iopll reset. + 80 :rpll reset. + 81 :gpio_pl_0 reset. + 82 :gpio_pl_1 reset. + 83 :gpio_pl_2 reset. + 84 :gpio_pl_3 reset. + 85 :gpio_pl_4 reset. + 86 :gpio_pl_5 reset. + 87 :gpio_pl_6 reset. + 88 :gpio_pl_7 reset. + 89 :gpio_pl_8 reset. + 90 :gpio_pl_9 reset. + 91 :gpio_pl_10 reset. + 92 :gpio_pl_11 reset. + 93 :gpio_pl_12 reset. + 94 :gpio_pl_13 reset. + 95 :gpio_pl_14 reset. + 96 :gpio_pl_15 reset. + 97 :gpio_pl_16 reset. + 98 :gpio_pl_17 reset. + 99 :gpio_pl_18 reset. + 100 :gpio_pl_19 reset. + 101 :gpio_pl_20 reset. + 102 :gpio_pl_21 reset. + 103 :gpio_pl_22 reset. + 104 :gpio_pl_23 reset. + 105 :gpio_pl_24 reset. + 106 :gpio_pl_25 reset. + 107 :gpio_pl_26 reset. + 108 :gpio_pl_27 reset. + 109 :gpio_pl_28 reset. + 110 :gpio_pl_29 reset. + 111 :gpio_pl_30 reset. + 112 :gpio_pl_31 reset. + 113 :rpu_ls reset. + 114 :ps_only reset. + 115 :pl reset. + 116 :ps_pl0 reset + 117 :ps_pl1 reset + 118 :ps_pl2 reset + 119 :ps_pl3 reset + ------- Example ------- @@ -25,5 +163,9 @@ firmware { zynqmp_firmware: zynqmp-firmware { compatible = "xlnx,zynqmp-firmware"; method = "smc"; + reset-controller:reset-controller at 0 { + compatible = "xlnx,zynqmp-reset"; + #reset-cells = <1>; + }; }; }; -- 2.7.4 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RFC PATCH v2 2/3] dt-bindings: fpga: Add bindings for ZynqMP reset driver @ 2018-09-05 6:40 ` Nava kishore Manne 0 siblings, 0 replies; 12+ messages in thread From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw) To: robh+dt, mark.rutland, michal.simek, p.zabel, nava.manne, rajanv, jollys, devicetree, linux-arm-kernel, linux-kernel Add documentation to describe Xilinx ZynqMP reset driver bindings. Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com> --- Changes for v2: -Moved reset node as a child to firwmare node. .../firmware/xilinx/xlnx,zynqmp-firmware.txt | 142 +++++++++++++++++++++ 1 file changed, 142 insertions(+) diff --git a/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt b/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt index 1b431d9..351b1bb 100644 --- a/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt +++ b/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt @@ -17,6 +17,144 @@ Required properties: - "smc" : SMC #0, following the SMCCC - "hvc" : HVC #0, following the SMCCC +-------------------------------------------------------------------------- + = Zynq UltraScale+ MPSoC reset driver binding = +-------------------------------------------------------------------------- +The Zynq UltraScale+ MPSoC has several different resets. + +See Chapter 36 of the Zynq UltraScale+ MPSoC TRM (UG) for more information +about zynqmp resets. + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Required Properties: +- compatible: "xlnx,zynqmp-reset" +- #reset-cells: Specifies the number of cells needed to encode reset + line, should be 1 + +Reset outputs: + 0 :PCIE config reset. + 1 :PCIE bridge block level reset (AXI interface). + 2 :PCIE control block level,reset. + 3 :Display Port block level reset (includes DPDMA). + 4 :FPD WDT reset. + 5 :AF_FM5 block level reset. + 6 :AF_FM4 block level reset. + 7 :AF_FM3 block level reset. + 8 :AF_FM2 block level reset. + 9 :AF_FM1 block level reset. + 10 :AF_FM0 block level reset. + 11 :GDMA block level reset. + 12 :Pixel Processor (GPU_PP1) block level reset. + 13 :Pixel Processor (GPU_PP0) block level reset. + 14 :GPU block level reset. + 15 :GT block level reset. + 16 :Sata block level reset. + 17 :ACPU3 power on reset. + 18 :ACPU2 power on reset. + 19 :ACPU1 power on reset. + 20 :ACPU0 power on reset. + 21 :APU L2 reset. + 22 :ACPU3 reset. + 23 :ACPU2 reset. + 24 :ACPU1 reset. + 25 :ACPU0 reset. + 26 :DDR block level reset inside of the DDR Sub System. + 27 :APM block level reset inside of the DDR Sub System. + 28 :soft reset. + 29 :GEM 0 reset. + 30 :GEM 1 reset. + 31 :GEM 2 reset. + 32 :GEM 3 reset. + 33 :qspi reset. + 34 :uart0 reset. + 35 :uart1 reset. + 36 :spi0 reset. + 37 :spi1 reset. + 38 :sdio0 reset. + 39 :sdio1 reset. + 40 :can0 reset. + 41 :can1 reset. + 42 :i2c0 reset. + 43 :i2c1 reset. + 44 :ttc0 reset. + 45 :ttc1 reset. + 46 :ttc2 reset. + 47 :ttc3 reset. + 48 :swdt reset. + 49 :nand reset. + 50 :adma reset. + 51 :gpio reset. + 52 :iou_cc reset. + 53 :timestamp reset. + 54 :rpu_r50 reset. + 55 :rpu r51 reset. + 56 :rpu_amba reset. + 57 :ocm reset. + 58 :rpu_pge reset. + 59 :usb0_core reset. + 60 :usb1_core reset. + 61 :usb0_hiber reset. + 62 :usb1_hiber reset. + 63 :usb0_apb reset. + 64 :usb1_apb reset. + 65 :ipi reset. + 66 :apm reset. + 67 :rtc reset. + 68 :sysmon reset. + 69 :afi_fm6 reset. + 70 :lpd_swdt reset. + 71 :fpd_reset. + 72 :rpu_dbg1 reset. + 73 :rpu_dbg0 reset. + 74 :dbg_lpd reset. + 75 :dbg_fpd reset. + 76 :apll reset. + 77 :dpll reset. + 78 :vpll reset. + 79 :iopll reset. + 80 :rpll reset. + 81 :gpio_pl_0 reset. + 82 :gpio_pl_1 reset. + 83 :gpio_pl_2 reset. + 84 :gpio_pl_3 reset. + 85 :gpio_pl_4 reset. + 86 :gpio_pl_5 reset. + 87 :gpio_pl_6 reset. + 88 :gpio_pl_7 reset. + 89 :gpio_pl_8 reset. + 90 :gpio_pl_9 reset. + 91 :gpio_pl_10 reset. + 92 :gpio_pl_11 reset. + 93 :gpio_pl_12 reset. + 94 :gpio_pl_13 reset. + 95 :gpio_pl_14 reset. + 96 :gpio_pl_15 reset. + 97 :gpio_pl_16 reset. + 98 :gpio_pl_17 reset. + 99 :gpio_pl_18 reset. + 100 :gpio_pl_19 reset. + 101 :gpio_pl_20 reset. + 102 :gpio_pl_21 reset. + 103 :gpio_pl_22 reset. + 104 :gpio_pl_23 reset. + 105 :gpio_pl_24 reset. + 106 :gpio_pl_25 reset. + 107 :gpio_pl_26 reset. + 108 :gpio_pl_27 reset. + 109 :gpio_pl_28 reset. + 110 :gpio_pl_29 reset. + 111 :gpio_pl_30 reset. + 112 :gpio_pl_31 reset. + 113 :rpu_ls reset. + 114 :ps_only reset. + 115 :pl reset. + 116 :ps_pl0 reset + 117 :ps_pl1 reset + 118 :ps_pl2 reset + 119 :ps_pl3 reset + ------- Example ------- @@ -25,5 +163,9 @@ firmware { zynqmp_firmware: zynqmp-firmware { compatible = "xlnx,zynqmp-firmware"; method = "smc"; + reset-controller:reset-controller@0 { + compatible = "xlnx,zynqmp-reset"; + #reset-cells = <1>; + }; }; }; -- 2.7.4 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RFC PATCH v2 3/3] reset: reset-zynqmp: Adding support for Xilinx zynqmp reset controller. 2018-09-05 6:40 ` Nava kishore Manne (?) @ 2018-09-05 6:40 ` Nava kishore Manne -1 siblings, 0 replies; 12+ messages in thread From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw) To: robh+dt, mark.rutland, michal.simek, p.zabel, nava.manne, rajanv, jollys, devicetree, linux-arm-kernel, linux-kernel Add a reset controller driver for Xilinx Zynq UltraScale+ MPSoC. The zynqmp reset-controller has the ability to reset lines connected to different blocks and peripheral in the Soc. Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com> --- Changes for v2: -Moved eemi_ops into a priv struct as suggested by philipp. drivers/reset/Makefile | 1 + drivers/reset/reset-zynqmp.c | 115 +++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 116 insertions(+) create mode 100644 drivers/reset/reset-zynqmp.c diff --git a/drivers/reset/Makefile b/drivers/reset/Makefile index c1261dc..27e4a33 100644 --- a/drivers/reset/Makefile +++ b/drivers/reset/Makefile @@ -21,4 +21,5 @@ obj-$(CONFIG_RESET_TI_SCI) += reset-ti-sci.o obj-$(CONFIG_RESET_TI_SYSCON) += reset-ti-syscon.o obj-$(CONFIG_RESET_UNIPHIER) += reset-uniphier.o obj-$(CONFIG_RESET_ZYNQ) += reset-zynq.o +obj-$(CONFIG_ARCH_ZYNQMP) += reset-zynqmp.o diff --git a/drivers/reset/reset-zynqmp.c b/drivers/reset/reset-zynqmp.c new file mode 100644 index 0000000..f908492 --- /dev/null +++ b/drivers/reset/reset-zynqmp.c @@ -0,0 +1,115 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2018 Xilinx, Inc. + * + */ + +#include <linux/io.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/reset-controller.h> +#include <linux/firmware/xlnx-zynqmp.h> + +#define ZYNQMP_NR_RESETS (ZYNQMP_PM_RESET_END - ZYNQMP_PM_RESET_START - 2) +#define ZYNQMP_RESET_ID (ZYNQMP_PM_RESET_START + 1) + +struct zynqmp_reset_data { + struct reset_controller_dev rcdev; + const struct zynqmp_eemi_ops *eemi_ops; +}; + +static inline struct zynqmp_reset_data * +to_zynqmp_reset_data(struct reset_controller_dev *rcdev) +{ + return container_of(rcdev, struct zynqmp_reset_data, rcdev); +} + +static int zynqmp_reset_assert(struct reset_controller_dev *rcdev, + unsigned long id) +{ + struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev); + + return priv->eemi_ops->reset_assert(ZYNQMP_RESET_ID + id, + PM_RESET_ACTION_ASSERT); +} + +static int zynqmp_reset_deassert(struct reset_controller_dev *rcdev, + unsigned long id) +{ + struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev); + + return priv->eemi_ops->reset_assert(ZYNQMP_RESET_ID + id, + PM_RESET_ACTION_RELEASE); +} + +static int zynqmp_reset_status(struct reset_controller_dev *rcdev, + unsigned long id) +{ + struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev); + int val, err; + + err = priv->eemi_ops->reset_get_status(ZYNQMP_RESET_ID + id, &val); + if (!err) + return -EINVAL; + + return val; +} + +static int zynqmp_reset_reset(struct reset_controller_dev *rcdev, + unsigned long id) +{ + struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev); + + return priv->eemi_ops->reset_assert(ZYNQMP_RESET_ID + id, + PM_RESET_ACTION_PULSE); +} + +static struct reset_control_ops zynqmp_reset_ops = { + .reset = zynqmp_reset_reset, + .assert = zynqmp_reset_assert, + .deassert = zynqmp_reset_deassert, + .status = zynqmp_reset_status, +}; + +static int zynqmp_reset_probe(struct platform_device *pdev) +{ + struct zynqmp_reset_data *priv; + + priv = devm_kzalloc(&pdev->dev, + sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + platform_set_drvdata(pdev, priv); + + priv->eemi_ops = zynqmp_pm_get_eemi_ops(); + if (!priv->eemi_ops) + return -ENXIO; + + priv->rcdev.ops = &zynqmp_reset_ops; + priv->rcdev.owner = THIS_MODULE; + priv->rcdev.of_node = pdev->dev.of_node; + priv->rcdev.nr_resets = ZYNQMP_NR_RESETS; + + return devm_reset_controller_register(&pdev->dev, &priv->rcdev); +} + +static const struct of_device_id zynqmp_reset_dt_ids[] = { + { .compatible = "xlnx,zynqmp-reset", }, + { }, +}; + +static struct platform_driver zynqmp_reset_driver = { + .probe = zynqmp_reset_probe, + .driver = { + .name = KBUILD_MODNAME, + .of_match_table = zynqmp_reset_dt_ids, + }, +}; + +static int __init zynqmp_reset_init(void) +{ + return platform_driver_register(&zynqmp_reset_driver); +} + +arch_initcall(zynqmp_reset_init); -- 2.7.4 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RFC PATCH v2 3/3] reset: reset-zynqmp: Adding support for Xilinx zynqmp reset controller. @ 2018-09-05 6:40 ` Nava kishore Manne 0 siblings, 0 replies; 12+ messages in thread From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw) To: linux-arm-kernel Add a reset controller driver for Xilinx Zynq UltraScale+ MPSoC. The zynqmp reset-controller has the ability to reset lines connected to different blocks and peripheral in the Soc. Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com> --- Changes for v2: -Moved eemi_ops into a priv struct as suggested by philipp. drivers/reset/Makefile | 1 + drivers/reset/reset-zynqmp.c | 115 +++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 116 insertions(+) create mode 100644 drivers/reset/reset-zynqmp.c diff --git a/drivers/reset/Makefile b/drivers/reset/Makefile index c1261dc..27e4a33 100644 --- a/drivers/reset/Makefile +++ b/drivers/reset/Makefile @@ -21,4 +21,5 @@ obj-$(CONFIG_RESET_TI_SCI) += reset-ti-sci.o obj-$(CONFIG_RESET_TI_SYSCON) += reset-ti-syscon.o obj-$(CONFIG_RESET_UNIPHIER) += reset-uniphier.o obj-$(CONFIG_RESET_ZYNQ) += reset-zynq.o +obj-$(CONFIG_ARCH_ZYNQMP) += reset-zynqmp.o diff --git a/drivers/reset/reset-zynqmp.c b/drivers/reset/reset-zynqmp.c new file mode 100644 index 0000000..f908492 --- /dev/null +++ b/drivers/reset/reset-zynqmp.c @@ -0,0 +1,115 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2018 Xilinx, Inc. + * + */ + +#include <linux/io.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/reset-controller.h> +#include <linux/firmware/xlnx-zynqmp.h> + +#define ZYNQMP_NR_RESETS (ZYNQMP_PM_RESET_END - ZYNQMP_PM_RESET_START - 2) +#define ZYNQMP_RESET_ID (ZYNQMP_PM_RESET_START + 1) + +struct zynqmp_reset_data { + struct reset_controller_dev rcdev; + const struct zynqmp_eemi_ops *eemi_ops; +}; + +static inline struct zynqmp_reset_data * +to_zynqmp_reset_data(struct reset_controller_dev *rcdev) +{ + return container_of(rcdev, struct zynqmp_reset_data, rcdev); +} + +static int zynqmp_reset_assert(struct reset_controller_dev *rcdev, + unsigned long id) +{ + struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev); + + return priv->eemi_ops->reset_assert(ZYNQMP_RESET_ID + id, + PM_RESET_ACTION_ASSERT); +} + +static int zynqmp_reset_deassert(struct reset_controller_dev *rcdev, + unsigned long id) +{ + struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev); + + return priv->eemi_ops->reset_assert(ZYNQMP_RESET_ID + id, + PM_RESET_ACTION_RELEASE); +} + +static int zynqmp_reset_status(struct reset_controller_dev *rcdev, + unsigned long id) +{ + struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev); + int val, err; + + err = priv->eemi_ops->reset_get_status(ZYNQMP_RESET_ID + id, &val); + if (!err) + return -EINVAL; + + return val; +} + +static int zynqmp_reset_reset(struct reset_controller_dev *rcdev, + unsigned long id) +{ + struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev); + + return priv->eemi_ops->reset_assert(ZYNQMP_RESET_ID + id, + PM_RESET_ACTION_PULSE); +} + +static struct reset_control_ops zynqmp_reset_ops = { + .reset = zynqmp_reset_reset, + .assert = zynqmp_reset_assert, + .deassert = zynqmp_reset_deassert, + .status = zynqmp_reset_status, +}; + +static int zynqmp_reset_probe(struct platform_device *pdev) +{ + struct zynqmp_reset_data *priv; + + priv = devm_kzalloc(&pdev->dev, + sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + platform_set_drvdata(pdev, priv); + + priv->eemi_ops = zynqmp_pm_get_eemi_ops(); + if (!priv->eemi_ops) + return -ENXIO; + + priv->rcdev.ops = &zynqmp_reset_ops; + priv->rcdev.owner = THIS_MODULE; + priv->rcdev.of_node = pdev->dev.of_node; + priv->rcdev.nr_resets = ZYNQMP_NR_RESETS; + + return devm_reset_controller_register(&pdev->dev, &priv->rcdev); +} + +static const struct of_device_id zynqmp_reset_dt_ids[] = { + { .compatible = "xlnx,zynqmp-reset", }, + { }, +}; + +static struct platform_driver zynqmp_reset_driver = { + .probe = zynqmp_reset_probe, + .driver = { + .name = KBUILD_MODNAME, + .of_match_table = zynqmp_reset_dt_ids, + }, +}; + +static int __init zynqmp_reset_init(void) +{ + return platform_driver_register(&zynqmp_reset_driver); +} + +arch_initcall(zynqmp_reset_init); -- 2.7.4 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RFC PATCH v2 3/3] reset: reset-zynqmp: Adding support for Xilinx zynqmp reset controller. @ 2018-09-05 6:40 ` Nava kishore Manne 0 siblings, 0 replies; 12+ messages in thread From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw) To: robh+dt, mark.rutland, michal.simek, p.zabel, nava.manne, rajanv, jollys, devicetree, linux-arm-kernel, linux-kernel Add a reset controller driver for Xilinx Zynq UltraScale+ MPSoC. The zynqmp reset-controller has the ability to reset lines connected to different blocks and peripheral in the Soc. Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com> --- Changes for v2: -Moved eemi_ops into a priv struct as suggested by philipp. drivers/reset/Makefile | 1 + drivers/reset/reset-zynqmp.c | 115 +++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 116 insertions(+) create mode 100644 drivers/reset/reset-zynqmp.c diff --git a/drivers/reset/Makefile b/drivers/reset/Makefile index c1261dc..27e4a33 100644 --- a/drivers/reset/Makefile +++ b/drivers/reset/Makefile @@ -21,4 +21,5 @@ obj-$(CONFIG_RESET_TI_SCI) += reset-ti-sci.o obj-$(CONFIG_RESET_TI_SYSCON) += reset-ti-syscon.o obj-$(CONFIG_RESET_UNIPHIER) += reset-uniphier.o obj-$(CONFIG_RESET_ZYNQ) += reset-zynq.o +obj-$(CONFIG_ARCH_ZYNQMP) += reset-zynqmp.o diff --git a/drivers/reset/reset-zynqmp.c b/drivers/reset/reset-zynqmp.c new file mode 100644 index 0000000..f908492 --- /dev/null +++ b/drivers/reset/reset-zynqmp.c @@ -0,0 +1,115 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2018 Xilinx, Inc. + * + */ + +#include <linux/io.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/reset-controller.h> +#include <linux/firmware/xlnx-zynqmp.h> + +#define ZYNQMP_NR_RESETS (ZYNQMP_PM_RESET_END - ZYNQMP_PM_RESET_START - 2) +#define ZYNQMP_RESET_ID (ZYNQMP_PM_RESET_START + 1) + +struct zynqmp_reset_data { + struct reset_controller_dev rcdev; + const struct zynqmp_eemi_ops *eemi_ops; +}; + +static inline struct zynqmp_reset_data * +to_zynqmp_reset_data(struct reset_controller_dev *rcdev) +{ + return container_of(rcdev, struct zynqmp_reset_data, rcdev); +} + +static int zynqmp_reset_assert(struct reset_controller_dev *rcdev, + unsigned long id) +{ + struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev); + + return priv->eemi_ops->reset_assert(ZYNQMP_RESET_ID + id, + PM_RESET_ACTION_ASSERT); +} + +static int zynqmp_reset_deassert(struct reset_controller_dev *rcdev, + unsigned long id) +{ + struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev); + + return priv->eemi_ops->reset_assert(ZYNQMP_RESET_ID + id, + PM_RESET_ACTION_RELEASE); +} + +static int zynqmp_reset_status(struct reset_controller_dev *rcdev, + unsigned long id) +{ + struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev); + int val, err; + + err = priv->eemi_ops->reset_get_status(ZYNQMP_RESET_ID + id, &val); + if (!err) + return -EINVAL; + + return val; +} + +static int zynqmp_reset_reset(struct reset_controller_dev *rcdev, + unsigned long id) +{ + struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev); + + return priv->eemi_ops->reset_assert(ZYNQMP_RESET_ID + id, + PM_RESET_ACTION_PULSE); +} + +static struct reset_control_ops zynqmp_reset_ops = { + .reset = zynqmp_reset_reset, + .assert = zynqmp_reset_assert, + .deassert = zynqmp_reset_deassert, + .status = zynqmp_reset_status, +}; + +static int zynqmp_reset_probe(struct platform_device *pdev) +{ + struct zynqmp_reset_data *priv; + + priv = devm_kzalloc(&pdev->dev, + sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + platform_set_drvdata(pdev, priv); + + priv->eemi_ops = zynqmp_pm_get_eemi_ops(); + if (!priv->eemi_ops) + return -ENXIO; + + priv->rcdev.ops = &zynqmp_reset_ops; + priv->rcdev.owner = THIS_MODULE; + priv->rcdev.of_node = pdev->dev.of_node; + priv->rcdev.nr_resets = ZYNQMP_NR_RESETS; + + return devm_reset_controller_register(&pdev->dev, &priv->rcdev); +} + +static const struct of_device_id zynqmp_reset_dt_ids[] = { + { .compatible = "xlnx,zynqmp-reset", }, + { }, +}; + +static struct platform_driver zynqmp_reset_driver = { + .probe = zynqmp_reset_probe, + .driver = { + .name = KBUILD_MODNAME, + .of_match_table = zynqmp_reset_dt_ids, + }, +}; + +static int __init zynqmp_reset_init(void) +{ + return platform_driver_register(&zynqmp_reset_driver); +} + +arch_initcall(zynqmp_reset_init); -- 2.7.4 ^ permalink raw reply related [flat|nested] 12+ messages in thread
end of thread, other threads:[~2018-09-05 6:42 UTC | newest] Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2018-09-05 6:40 [RFC PATCH v2 0/3] Add reset driver support for ZynqMP Nava kishore Manne 2018-09-05 6:40 ` Nava kishore Manne 2018-09-05 6:40 ` Nava kishore Manne 2018-09-05 6:40 ` [RFC PATCH v2 1/3] firmware: xilinx: Add reset API's Nava kishore Manne 2018-09-05 6:40 ` Nava kishore Manne 2018-09-05 6:40 ` Nava kishore Manne 2018-09-05 6:40 ` [RFC PATCH v2 2/3] dt-bindings: fpga: Add bindings for ZynqMP reset driver Nava kishore Manne 2018-09-05 6:40 ` Nava kishore Manne 2018-09-05 6:40 ` Nava kishore Manne 2018-09-05 6:40 ` [RFC PATCH v2 3/3] reset: reset-zynqmp: Adding support for Xilinx zynqmp reset controller Nava kishore Manne 2018-09-05 6:40 ` Nava kishore Manne 2018-09-05 6:40 ` Nava kishore Manne
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.