* [RFC PATCH v2 0/3] Add reset driver support for ZynqMP
@ 2018-09-05 6:40 ` Nava kishore Manne
0 siblings, 0 replies; 12+ messages in thread
From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw)
To: robh+dt, mark.rutland, michal.simek, p.zabel, nava.manne, rajanv,
jollys, devicetree, linux-arm-kernel, linux-kernel
This series of patches are created On top of the
below series of patches.
https://lkml.org/lkml/2018/8/3/687
Nava kishore Manne (3):
firmware: xilinx: Add reset API's
dt-bindings: fpga: Add bindings for ZynqMP reset driver
reset: reset-zynqmp: Adding support for Xilinx zynqmp reset
controller.
.../firmware/xilinx/xlnx,zynqmp-firmware.txt | 142 +++++++++++++++++++++
drivers/firmware/xilinx/zynqmp.c | 40 ++++++
drivers/reset/Makefile | 1 +
drivers/reset/reset-zynqmp.c | 115 +++++++++++++++++
include/linux/firmware/xlnx-zynqmp.h | 136 ++++++++++++++++++++
5 files changed, 434 insertions(+)
create mode 100644 drivers/reset/reset-zynqmp.c
--
2.7.4
^ permalink raw reply [flat|nested] 12+ messages in thread
* [RFC PATCH v2 0/3] Add reset driver support for ZynqMP
@ 2018-09-05 6:40 ` Nava kishore Manne
0 siblings, 0 replies; 12+ messages in thread
From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw)
To: robh+dt, mark.rutland, michal.simek, p.zabel, nava.manne, rajanv,
jollys, devicetree, linux-arm-kernel, linux-kernel
This series of patches are created On top of the
below series of patches.
https://lkml.org/lkml/2018/8/3/687
Nava kishore Manne (3):
firmware: xilinx: Add reset API's
dt-bindings: fpga: Add bindings for ZynqMP reset driver
reset: reset-zynqmp: Adding support for Xilinx zynqmp reset
controller.
.../firmware/xilinx/xlnx,zynqmp-firmware.txt | 142 +++++++++++++++++++++
drivers/firmware/xilinx/zynqmp.c | 40 ++++++
drivers/reset/Makefile | 1 +
drivers/reset/reset-zynqmp.c | 115 +++++++++++++++++
include/linux/firmware/xlnx-zynqmp.h | 136 ++++++++++++++++++++
5 files changed, 434 insertions(+)
create mode 100644 drivers/reset/reset-zynqmp.c
--
2.7.4
^ permalink raw reply [flat|nested] 12+ messages in thread
* [RFC PATCH v2 0/3] Add reset driver support for ZynqMP
@ 2018-09-05 6:40 ` Nava kishore Manne
0 siblings, 0 replies; 12+ messages in thread
From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw)
To: linux-arm-kernel
This series of patches are created On top of the
below series of patches.
https://lkml.org/lkml/2018/8/3/687
Nava kishore Manne (3):
firmware: xilinx: Add reset API's
dt-bindings: fpga: Add bindings for ZynqMP reset driver
reset: reset-zynqmp: Adding support for Xilinx zynqmp reset
controller.
.../firmware/xilinx/xlnx,zynqmp-firmware.txt | 142 +++++++++++++++++++++
drivers/firmware/xilinx/zynqmp.c | 40 ++++++
drivers/reset/Makefile | 1 +
drivers/reset/reset-zynqmp.c | 115 +++++++++++++++++
include/linux/firmware/xlnx-zynqmp.h | 136 ++++++++++++++++++++
5 files changed, 434 insertions(+)
create mode 100644 drivers/reset/reset-zynqmp.c
--
2.7.4
^ permalink raw reply [flat|nested] 12+ messages in thread
* [RFC PATCH v2 1/3] firmware: xilinx: Add reset API's
2018-09-05 6:40 ` Nava kishore Manne
(?)
@ 2018-09-05 6:40 ` Nava kishore Manne
-1 siblings, 0 replies; 12+ messages in thread
From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw)
To: robh+dt, mark.rutland, michal.simek, p.zabel, nava.manne, rajanv,
jollys, devicetree, linux-arm-kernel, linux-kernel
This Patch Adds reset API's to support release, assert
and status functionalities by using firmware interface.
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
---
Changes for v2:
-New Patch.
drivers/firmware/xilinx/zynqmp.c | 40 +++++++++++
include/linux/firmware/xlnx-zynqmp.h | 136 +++++++++++++++++++++++++++++++++++
2 files changed, 176 insertions(+)
diff --git a/drivers/firmware/xilinx/zynqmp.c b/drivers/firmware/xilinx/zynqmp.c
index 7ccedf0..639c72f 100644
--- a/drivers/firmware/xilinx/zynqmp.c
+++ b/drivers/firmware/xilinx/zynqmp.c
@@ -447,6 +447,44 @@ static int zynqmp_pm_clock_getparent(u32 clock_id, u32 *parent_id)
return ret;
}
+/**
+ * zynqmp_pm_reset_assert - Request setting of reset (1 - assert, 0 - release)
+ * @reset: Reset to be configured
+ * @assert_flag: Flag stating should reset be asserted (1) or
+ * released (0)
+ *
+ * Return: Returns status, either success or error+reason
+ */
+static int zynqmp_pm_reset_assert(const enum zynqmp_pm_reset reset,
+ const enum zynqmp_pm_reset_action assert_flag)
+{
+ return zynqmp_pm_invoke_fn(PM_RESET_ASSERT, reset, assert_flag,
+ 0, 0, NULL);
+}
+
+/**
+ * zynqmp_pm_reset_get_status - Get status of the reset
+ * @reset: Reset whose status should be returned
+ * @status: Returned status
+ *
+ * Return: Returns status, either success or error+reason
+ */
+static int zynqmp_pm_reset_get_status(const enum zynqmp_pm_reset reset,
+ u32 *status)
+{
+ u32 ret_payload[PAYLOAD_ARG_CNT];
+ int ret;
+
+ if (!status)
+ return -EINVAL;
+
+ ret = zynqmp_pm_invoke_fn(PM_RESET_GET_STATUS, reset, 0,
+ 0, 0, ret_payload);
+ *status = ret_payload[1];
+
+ return ret;
+}
+
static const struct zynqmp_eemi_ops eemi_ops = {
.get_api_version = zynqmp_pm_get_api_version,
.ioctl = zynqmp_pm_ioctl,
@@ -460,6 +498,8 @@ static const struct zynqmp_eemi_ops eemi_ops = {
.clock_getrate = zynqmp_pm_clock_getrate,
.clock_setparent = zynqmp_pm_clock_setparent,
.clock_getparent = zynqmp_pm_clock_getparent,
+ .reset_assert = zynqmp_pm_reset_assert,
+ .reset_get_status = zynqmp_pm_reset_get_status,
};
/**
diff --git a/include/linux/firmware/xlnx-zynqmp.h b/include/linux/firmware/xlnx-zynqmp.h
index 58a7478..93decf5 100644
--- a/include/linux/firmware/xlnx-zynqmp.h
+++ b/include/linux/firmware/xlnx-zynqmp.h
@@ -34,6 +34,8 @@
enum pm_api_id {
PM_GET_API_VERSION = 1,
+ PM_RESET_ASSERT = 17,
+ PM_RESET_GET_STATUS,
PM_IOCTL = 34,
PM_QUERY_DATA,
PM_CLOCK_ENABLE,
@@ -74,6 +76,137 @@ enum pm_query_id {
PM_QID_CLOCK_GET_ATTRIBUTES,
};
+enum zynqmp_pm_reset_action {
+ PM_RESET_ACTION_RELEASE,
+ PM_RESET_ACTION_ASSERT,
+ PM_RESET_ACTION_PULSE,
+};
+
+enum zynqmp_pm_reset {
+ ZYNQMP_PM_RESET_START = 999,
+ ZYNQMP_PM_RESET_PCIE_CFG,
+ ZYNQMP_PM_RESET_PCIE_BRIDGE,
+ ZYNQMP_PM_RESET_PCIE_CTRL,
+ ZYNQMP_PM_RESET_DP,
+ ZYNQMP_PM_RESET_SWDT_CRF,
+ ZYNQMP_PM_RESET_AFI_FM5,
+ ZYNQMP_PM_RESET_AFI_FM4,
+ ZYNQMP_PM_RESET_AFI_FM3,
+ ZYNQMP_PM_RESET_AFI_FM2,
+ ZYNQMP_PM_RESET_AFI_FM1,
+ ZYNQMP_PM_RESET_AFI_FM0,
+ ZYNQMP_PM_RESET_GDMA,
+ ZYNQMP_PM_RESET_GPU_PP1,
+ ZYNQMP_PM_RESET_GPU_PP0,
+ ZYNQMP_PM_RESET_GPU,
+ ZYNQMP_PM_RESET_GT,
+ ZYNQMP_PM_RESET_SATA,
+ ZYNQMP_PM_RESET_ACPU3_PWRON,
+ ZYNQMP_PM_RESET_ACPU2_PWRON,
+ ZYNQMP_PM_RESET_ACPU1_PWRON,
+ ZYNQMP_PM_RESET_ACPU0_PWRON,
+ ZYNQMP_PM_RESET_APU_L2,
+ ZYNQMP_PM_RESET_ACPU3,
+ ZYNQMP_PM_RESET_ACPU2,
+ ZYNQMP_PM_RESET_ACPU1,
+ ZYNQMP_PM_RESET_ACPU0,
+ ZYNQMP_PM_RESET_DDR,
+ ZYNQMP_PM_RESET_APM_FPD,
+ ZYNQMP_PM_RESET_SOFT,
+ ZYNQMP_PM_RESET_GEM0,
+ ZYNQMP_PM_RESET_GEM1,
+ ZYNQMP_PM_RESET_GEM2,
+ ZYNQMP_PM_RESET_GEM3,
+ ZYNQMP_PM_RESET_QSPI,
+ ZYNQMP_PM_RESET_UART0,
+ ZYNQMP_PM_RESET_UART1,
+ ZYNQMP_PM_RESET_SPI0,
+ ZYNQMP_PM_RESET_SPI1,
+ ZYNQMP_PM_RESET_SDIO0,
+ ZYNQMP_PM_RESET_SDIO1,
+ ZYNQMP_PM_RESET_CAN0,
+ ZYNQMP_PM_RESET_CAN1,
+ ZYNQMP_PM_RESET_I2C0,
+ ZYNQMP_PM_RESET_I2C1,
+ ZYNQMP_PM_RESET_TTC0,
+ ZYNQMP_PM_RESET_TTC1,
+ ZYNQMP_PM_RESET_TTC2,
+ ZYNQMP_PM_RESET_TTC3,
+ ZYNQMP_PM_RESET_SWDT_CRL,
+ ZYNQMP_PM_RESET_NAND,
+ ZYNQMP_PM_RESET_ADMA,
+ ZYNQMP_PM_RESET_GPIO,
+ ZYNQMP_PM_RESET_IOU_CC,
+ ZYNQMP_PM_RESET_TIMESTAMP,
+ ZYNQMP_PM_RESET_RPU_R50,
+ ZYNQMP_PM_RESET_RPU_R51,
+ ZYNQMP_PM_RESET_RPU_AMBA,
+ ZYNQMP_PM_RESET_OCM,
+ ZYNQMP_PM_RESET_RPU_PGE,
+ ZYNQMP_PM_RESET_USB0_CORERESET,
+ ZYNQMP_PM_RESET_USB1_CORERESET,
+ ZYNQMP_PM_RESET_USB0_HIBERRESET,
+ ZYNQMP_PM_RESET_USB1_HIBERRESET,
+ ZYNQMP_PM_RESET_USB0_APB,
+ ZYNQMP_PM_RESET_USB1_APB,
+ ZYNQMP_PM_RESET_IPI,
+ ZYNQMP_PM_RESET_APM_LPD,
+ ZYNQMP_PM_RESET_RTC,
+ ZYNQMP_PM_RESET_SYSMON,
+ ZYNQMP_PM_RESET_AFI_FM6,
+ ZYNQMP_PM_RESET_LPD_SWDT,
+ ZYNQMP_PM_RESET_FPD,
+ ZYNQMP_PM_RESET_RPU_DBG1,
+ ZYNQMP_PM_RESET_RPU_DBG0,
+ ZYNQMP_PM_RESET_DBG_LPD,
+ ZYNQMP_PM_RESET_DBG_FPD,
+ ZYNQMP_PM_RESET_APLL,
+ ZYNQMP_PM_RESET_DPLL,
+ ZYNQMP_PM_RESET_VPLL,
+ ZYNQMP_PM_RESET_IOPLL,
+ ZYNQMP_PM_RESET_RPLL,
+ ZYNQMP_PM_RESET_GPO3_PL_0,
+ ZYNQMP_PM_RESET_GPO3_PL_1,
+ ZYNQMP_PM_RESET_GPO3_PL_2,
+ ZYNQMP_PM_RESET_GPO3_PL_3,
+ ZYNQMP_PM_RESET_GPO3_PL_4,
+ ZYNQMP_PM_RESET_GPO3_PL_5,
+ ZYNQMP_PM_RESET_GPO3_PL_6,
+ ZYNQMP_PM_RESET_GPO3_PL_7,
+ ZYNQMP_PM_RESET_GPO3_PL_8,
+ ZYNQMP_PM_RESET_GPO3_PL_9,
+ ZYNQMP_PM_RESET_GPO3_PL_10,
+ ZYNQMP_PM_RESET_GPO3_PL_11,
+ ZYNQMP_PM_RESET_GPO3_PL_12,
+ ZYNQMP_PM_RESET_GPO3_PL_13,
+ ZYNQMP_PM_RESET_GPO3_PL_14,
+ ZYNQMP_PM_RESET_GPO3_PL_15,
+ ZYNQMP_PM_RESET_GPO3_PL_16,
+ ZYNQMP_PM_RESET_GPO3_PL_17,
+ ZYNQMP_PM_RESET_GPO3_PL_18,
+ ZYNQMP_PM_RESET_GPO3_PL_19,
+ ZNQMP_PM_RESET_GPO3_PL_20,
+ ZYNQMP_PM_RESET_GPO3_PL_21,
+ ZYNQMP_PM_RESET_GPO3_PL_22,
+ ZYNQMP_PM_RESET_GPO3_PL_23,
+ ZYNQMP_PM_RESET_GPO3_PL_24,
+ ZYNQMP_PM_RESET_GPO3_PL_25,
+ ZYNQMP_PM_RESET_GPO3_PL_26,
+ ZYNQMP_PM_RESET_GPO3_PL_27,
+ ZYNQMP_PM_RESET_GPO3_PL_28,
+ ZYNQMP_PM_RESET_GPO3_PL_29,
+ ZYNQMP_PM_RESET_GPO3_PL_30,
+ ZYNQMP_PM_RESET_GPO3_PL_31,
+ ZYNQMP_PM_RESET_RPU_LS,
+ ZYNQMP_PM_RESET_PS_ONLY,
+ ZYNQMP_PM_RESET_PL,
+ ZYNQMP_PM_RESET_PS_PL0,
+ ZYNQMP_PM_RESET_PS_PL1,
+ ZYNQMP_PM_RESET_PS_PL2,
+ ZYNQMP_PM_RESET_PS_PL3,
+ ZYNQMP_PM_RESET_END
+};
+
/**
* struct zynqmp_pm_query_data - PM query data
* @qid: query ID
@@ -101,6 +234,9 @@ struct zynqmp_eemi_ops {
int (*clock_getrate)(u32 clock_id, u64 *rate);
int (*clock_setparent)(u32 clock_id, u32 parent_id);
int (*clock_getparent)(u32 clock_id, u32 *parent_id);
+ int (*reset_assert)(const enum zynqmp_pm_reset reset,
+ const enum zynqmp_pm_reset_action assert_flag);
+ int (*reset_get_status)(const enum zynqmp_pm_reset reset, u32 *status);
};
#if IS_REACHABLE(CONFIG_ARCH_ZYNQMP)
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RFC PATCH v2 1/3] firmware: xilinx: Add reset API's
@ 2018-09-05 6:40 ` Nava kishore Manne
0 siblings, 0 replies; 12+ messages in thread
From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw)
To: robh+dt, mark.rutland, michal.simek, p.zabel, nava.manne, rajanv,
jollys, devicetree, linux-arm-kernel, linux-kernel
This Patch Adds reset API's to support release, assert
and status functionalities by using firmware interface.
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
---
Changes for v2:
-New Patch.
drivers/firmware/xilinx/zynqmp.c | 40 +++++++++++
include/linux/firmware/xlnx-zynqmp.h | 136 +++++++++++++++++++++++++++++++++++
2 files changed, 176 insertions(+)
diff --git a/drivers/firmware/xilinx/zynqmp.c b/drivers/firmware/xilinx/zynqmp.c
index 7ccedf0..639c72f 100644
--- a/drivers/firmware/xilinx/zynqmp.c
+++ b/drivers/firmware/xilinx/zynqmp.c
@@ -447,6 +447,44 @@ static int zynqmp_pm_clock_getparent(u32 clock_id, u32 *parent_id)
return ret;
}
+/**
+ * zynqmp_pm_reset_assert - Request setting of reset (1 - assert, 0 - release)
+ * @reset: Reset to be configured
+ * @assert_flag: Flag stating should reset be asserted (1) or
+ * released (0)
+ *
+ * Return: Returns status, either success or error+reason
+ */
+static int zynqmp_pm_reset_assert(const enum zynqmp_pm_reset reset,
+ const enum zynqmp_pm_reset_action assert_flag)
+{
+ return zynqmp_pm_invoke_fn(PM_RESET_ASSERT, reset, assert_flag,
+ 0, 0, NULL);
+}
+
+/**
+ * zynqmp_pm_reset_get_status - Get status of the reset
+ * @reset: Reset whose status should be returned
+ * @status: Returned status
+ *
+ * Return: Returns status, either success or error+reason
+ */
+static int zynqmp_pm_reset_get_status(const enum zynqmp_pm_reset reset,
+ u32 *status)
+{
+ u32 ret_payload[PAYLOAD_ARG_CNT];
+ int ret;
+
+ if (!status)
+ return -EINVAL;
+
+ ret = zynqmp_pm_invoke_fn(PM_RESET_GET_STATUS, reset, 0,
+ 0, 0, ret_payload);
+ *status = ret_payload[1];
+
+ return ret;
+}
+
static const struct zynqmp_eemi_ops eemi_ops = {
.get_api_version = zynqmp_pm_get_api_version,
.ioctl = zynqmp_pm_ioctl,
@@ -460,6 +498,8 @@ static const struct zynqmp_eemi_ops eemi_ops = {
.clock_getrate = zynqmp_pm_clock_getrate,
.clock_setparent = zynqmp_pm_clock_setparent,
.clock_getparent = zynqmp_pm_clock_getparent,
+ .reset_assert = zynqmp_pm_reset_assert,
+ .reset_get_status = zynqmp_pm_reset_get_status,
};
/**
diff --git a/include/linux/firmware/xlnx-zynqmp.h b/include/linux/firmware/xlnx-zynqmp.h
index 58a7478..93decf5 100644
--- a/include/linux/firmware/xlnx-zynqmp.h
+++ b/include/linux/firmware/xlnx-zynqmp.h
@@ -34,6 +34,8 @@
enum pm_api_id {
PM_GET_API_VERSION = 1,
+ PM_RESET_ASSERT = 17,
+ PM_RESET_GET_STATUS,
PM_IOCTL = 34,
PM_QUERY_DATA,
PM_CLOCK_ENABLE,
@@ -74,6 +76,137 @@ enum pm_query_id {
PM_QID_CLOCK_GET_ATTRIBUTES,
};
+enum zynqmp_pm_reset_action {
+ PM_RESET_ACTION_RELEASE,
+ PM_RESET_ACTION_ASSERT,
+ PM_RESET_ACTION_PULSE,
+};
+
+enum zynqmp_pm_reset {
+ ZYNQMP_PM_RESET_START = 999,
+ ZYNQMP_PM_RESET_PCIE_CFG,
+ ZYNQMP_PM_RESET_PCIE_BRIDGE,
+ ZYNQMP_PM_RESET_PCIE_CTRL,
+ ZYNQMP_PM_RESET_DP,
+ ZYNQMP_PM_RESET_SWDT_CRF,
+ ZYNQMP_PM_RESET_AFI_FM5,
+ ZYNQMP_PM_RESET_AFI_FM4,
+ ZYNQMP_PM_RESET_AFI_FM3,
+ ZYNQMP_PM_RESET_AFI_FM2,
+ ZYNQMP_PM_RESET_AFI_FM1,
+ ZYNQMP_PM_RESET_AFI_FM0,
+ ZYNQMP_PM_RESET_GDMA,
+ ZYNQMP_PM_RESET_GPU_PP1,
+ ZYNQMP_PM_RESET_GPU_PP0,
+ ZYNQMP_PM_RESET_GPU,
+ ZYNQMP_PM_RESET_GT,
+ ZYNQMP_PM_RESET_SATA,
+ ZYNQMP_PM_RESET_ACPU3_PWRON,
+ ZYNQMP_PM_RESET_ACPU2_PWRON,
+ ZYNQMP_PM_RESET_ACPU1_PWRON,
+ ZYNQMP_PM_RESET_ACPU0_PWRON,
+ ZYNQMP_PM_RESET_APU_L2,
+ ZYNQMP_PM_RESET_ACPU3,
+ ZYNQMP_PM_RESET_ACPU2,
+ ZYNQMP_PM_RESET_ACPU1,
+ ZYNQMP_PM_RESET_ACPU0,
+ ZYNQMP_PM_RESET_DDR,
+ ZYNQMP_PM_RESET_APM_FPD,
+ ZYNQMP_PM_RESET_SOFT,
+ ZYNQMP_PM_RESET_GEM0,
+ ZYNQMP_PM_RESET_GEM1,
+ ZYNQMP_PM_RESET_GEM2,
+ ZYNQMP_PM_RESET_GEM3,
+ ZYNQMP_PM_RESET_QSPI,
+ ZYNQMP_PM_RESET_UART0,
+ ZYNQMP_PM_RESET_UART1,
+ ZYNQMP_PM_RESET_SPI0,
+ ZYNQMP_PM_RESET_SPI1,
+ ZYNQMP_PM_RESET_SDIO0,
+ ZYNQMP_PM_RESET_SDIO1,
+ ZYNQMP_PM_RESET_CAN0,
+ ZYNQMP_PM_RESET_CAN1,
+ ZYNQMP_PM_RESET_I2C0,
+ ZYNQMP_PM_RESET_I2C1,
+ ZYNQMP_PM_RESET_TTC0,
+ ZYNQMP_PM_RESET_TTC1,
+ ZYNQMP_PM_RESET_TTC2,
+ ZYNQMP_PM_RESET_TTC3,
+ ZYNQMP_PM_RESET_SWDT_CRL,
+ ZYNQMP_PM_RESET_NAND,
+ ZYNQMP_PM_RESET_ADMA,
+ ZYNQMP_PM_RESET_GPIO,
+ ZYNQMP_PM_RESET_IOU_CC,
+ ZYNQMP_PM_RESET_TIMESTAMP,
+ ZYNQMP_PM_RESET_RPU_R50,
+ ZYNQMP_PM_RESET_RPU_R51,
+ ZYNQMP_PM_RESET_RPU_AMBA,
+ ZYNQMP_PM_RESET_OCM,
+ ZYNQMP_PM_RESET_RPU_PGE,
+ ZYNQMP_PM_RESET_USB0_CORERESET,
+ ZYNQMP_PM_RESET_USB1_CORERESET,
+ ZYNQMP_PM_RESET_USB0_HIBERRESET,
+ ZYNQMP_PM_RESET_USB1_HIBERRESET,
+ ZYNQMP_PM_RESET_USB0_APB,
+ ZYNQMP_PM_RESET_USB1_APB,
+ ZYNQMP_PM_RESET_IPI,
+ ZYNQMP_PM_RESET_APM_LPD,
+ ZYNQMP_PM_RESET_RTC,
+ ZYNQMP_PM_RESET_SYSMON,
+ ZYNQMP_PM_RESET_AFI_FM6,
+ ZYNQMP_PM_RESET_LPD_SWDT,
+ ZYNQMP_PM_RESET_FPD,
+ ZYNQMP_PM_RESET_RPU_DBG1,
+ ZYNQMP_PM_RESET_RPU_DBG0,
+ ZYNQMP_PM_RESET_DBG_LPD,
+ ZYNQMP_PM_RESET_DBG_FPD,
+ ZYNQMP_PM_RESET_APLL,
+ ZYNQMP_PM_RESET_DPLL,
+ ZYNQMP_PM_RESET_VPLL,
+ ZYNQMP_PM_RESET_IOPLL,
+ ZYNQMP_PM_RESET_RPLL,
+ ZYNQMP_PM_RESET_GPO3_PL_0,
+ ZYNQMP_PM_RESET_GPO3_PL_1,
+ ZYNQMP_PM_RESET_GPO3_PL_2,
+ ZYNQMP_PM_RESET_GPO3_PL_3,
+ ZYNQMP_PM_RESET_GPO3_PL_4,
+ ZYNQMP_PM_RESET_GPO3_PL_5,
+ ZYNQMP_PM_RESET_GPO3_PL_6,
+ ZYNQMP_PM_RESET_GPO3_PL_7,
+ ZYNQMP_PM_RESET_GPO3_PL_8,
+ ZYNQMP_PM_RESET_GPO3_PL_9,
+ ZYNQMP_PM_RESET_GPO3_PL_10,
+ ZYNQMP_PM_RESET_GPO3_PL_11,
+ ZYNQMP_PM_RESET_GPO3_PL_12,
+ ZYNQMP_PM_RESET_GPO3_PL_13,
+ ZYNQMP_PM_RESET_GPO3_PL_14,
+ ZYNQMP_PM_RESET_GPO3_PL_15,
+ ZYNQMP_PM_RESET_GPO3_PL_16,
+ ZYNQMP_PM_RESET_GPO3_PL_17,
+ ZYNQMP_PM_RESET_GPO3_PL_18,
+ ZYNQMP_PM_RESET_GPO3_PL_19,
+ ZNQMP_PM_RESET_GPO3_PL_20,
+ ZYNQMP_PM_RESET_GPO3_PL_21,
+ ZYNQMP_PM_RESET_GPO3_PL_22,
+ ZYNQMP_PM_RESET_GPO3_PL_23,
+ ZYNQMP_PM_RESET_GPO3_PL_24,
+ ZYNQMP_PM_RESET_GPO3_PL_25,
+ ZYNQMP_PM_RESET_GPO3_PL_26,
+ ZYNQMP_PM_RESET_GPO3_PL_27,
+ ZYNQMP_PM_RESET_GPO3_PL_28,
+ ZYNQMP_PM_RESET_GPO3_PL_29,
+ ZYNQMP_PM_RESET_GPO3_PL_30,
+ ZYNQMP_PM_RESET_GPO3_PL_31,
+ ZYNQMP_PM_RESET_RPU_LS,
+ ZYNQMP_PM_RESET_PS_ONLY,
+ ZYNQMP_PM_RESET_PL,
+ ZYNQMP_PM_RESET_PS_PL0,
+ ZYNQMP_PM_RESET_PS_PL1,
+ ZYNQMP_PM_RESET_PS_PL2,
+ ZYNQMP_PM_RESET_PS_PL3,
+ ZYNQMP_PM_RESET_END
+};
+
/**
* struct zynqmp_pm_query_data - PM query data
* @qid: query ID
@@ -101,6 +234,9 @@ struct zynqmp_eemi_ops {
int (*clock_getrate)(u32 clock_id, u64 *rate);
int (*clock_setparent)(u32 clock_id, u32 parent_id);
int (*clock_getparent)(u32 clock_id, u32 *parent_id);
+ int (*reset_assert)(const enum zynqmp_pm_reset reset,
+ const enum zynqmp_pm_reset_action assert_flag);
+ int (*reset_get_status)(const enum zynqmp_pm_reset reset, u32 *status);
};
#if IS_REACHABLE(CONFIG_ARCH_ZYNQMP)
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RFC PATCH v2 1/3] firmware: xilinx: Add reset API's
@ 2018-09-05 6:40 ` Nava kishore Manne
0 siblings, 0 replies; 12+ messages in thread
From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw)
To: linux-arm-kernel
This Patch Adds reset API's to support release, assert
and status functionalities by using firmware interface.
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
---
Changes for v2:
-New Patch.
drivers/firmware/xilinx/zynqmp.c | 40 +++++++++++
include/linux/firmware/xlnx-zynqmp.h | 136 +++++++++++++++++++++++++++++++++++
2 files changed, 176 insertions(+)
diff --git a/drivers/firmware/xilinx/zynqmp.c b/drivers/firmware/xilinx/zynqmp.c
index 7ccedf0..639c72f 100644
--- a/drivers/firmware/xilinx/zynqmp.c
+++ b/drivers/firmware/xilinx/zynqmp.c
@@ -447,6 +447,44 @@ static int zynqmp_pm_clock_getparent(u32 clock_id, u32 *parent_id)
return ret;
}
+/**
+ * zynqmp_pm_reset_assert - Request setting of reset (1 - assert, 0 - release)
+ * @reset: Reset to be configured
+ * @assert_flag: Flag stating should reset be asserted (1) or
+ * released (0)
+ *
+ * Return: Returns status, either success or error+reason
+ */
+static int zynqmp_pm_reset_assert(const enum zynqmp_pm_reset reset,
+ const enum zynqmp_pm_reset_action assert_flag)
+{
+ return zynqmp_pm_invoke_fn(PM_RESET_ASSERT, reset, assert_flag,
+ 0, 0, NULL);
+}
+
+/**
+ * zynqmp_pm_reset_get_status - Get status of the reset
+ * @reset: Reset whose status should be returned
+ * @status: Returned status
+ *
+ * Return: Returns status, either success or error+reason
+ */
+static int zynqmp_pm_reset_get_status(const enum zynqmp_pm_reset reset,
+ u32 *status)
+{
+ u32 ret_payload[PAYLOAD_ARG_CNT];
+ int ret;
+
+ if (!status)
+ return -EINVAL;
+
+ ret = zynqmp_pm_invoke_fn(PM_RESET_GET_STATUS, reset, 0,
+ 0, 0, ret_payload);
+ *status = ret_payload[1];
+
+ return ret;
+}
+
static const struct zynqmp_eemi_ops eemi_ops = {
.get_api_version = zynqmp_pm_get_api_version,
.ioctl = zynqmp_pm_ioctl,
@@ -460,6 +498,8 @@ static const struct zynqmp_eemi_ops eemi_ops = {
.clock_getrate = zynqmp_pm_clock_getrate,
.clock_setparent = zynqmp_pm_clock_setparent,
.clock_getparent = zynqmp_pm_clock_getparent,
+ .reset_assert = zynqmp_pm_reset_assert,
+ .reset_get_status = zynqmp_pm_reset_get_status,
};
/**
diff --git a/include/linux/firmware/xlnx-zynqmp.h b/include/linux/firmware/xlnx-zynqmp.h
index 58a7478..93decf5 100644
--- a/include/linux/firmware/xlnx-zynqmp.h
+++ b/include/linux/firmware/xlnx-zynqmp.h
@@ -34,6 +34,8 @@
enum pm_api_id {
PM_GET_API_VERSION = 1,
+ PM_RESET_ASSERT = 17,
+ PM_RESET_GET_STATUS,
PM_IOCTL = 34,
PM_QUERY_DATA,
PM_CLOCK_ENABLE,
@@ -74,6 +76,137 @@ enum pm_query_id {
PM_QID_CLOCK_GET_ATTRIBUTES,
};
+enum zynqmp_pm_reset_action {
+ PM_RESET_ACTION_RELEASE,
+ PM_RESET_ACTION_ASSERT,
+ PM_RESET_ACTION_PULSE,
+};
+
+enum zynqmp_pm_reset {
+ ZYNQMP_PM_RESET_START = 999,
+ ZYNQMP_PM_RESET_PCIE_CFG,
+ ZYNQMP_PM_RESET_PCIE_BRIDGE,
+ ZYNQMP_PM_RESET_PCIE_CTRL,
+ ZYNQMP_PM_RESET_DP,
+ ZYNQMP_PM_RESET_SWDT_CRF,
+ ZYNQMP_PM_RESET_AFI_FM5,
+ ZYNQMP_PM_RESET_AFI_FM4,
+ ZYNQMP_PM_RESET_AFI_FM3,
+ ZYNQMP_PM_RESET_AFI_FM2,
+ ZYNQMP_PM_RESET_AFI_FM1,
+ ZYNQMP_PM_RESET_AFI_FM0,
+ ZYNQMP_PM_RESET_GDMA,
+ ZYNQMP_PM_RESET_GPU_PP1,
+ ZYNQMP_PM_RESET_GPU_PP0,
+ ZYNQMP_PM_RESET_GPU,
+ ZYNQMP_PM_RESET_GT,
+ ZYNQMP_PM_RESET_SATA,
+ ZYNQMP_PM_RESET_ACPU3_PWRON,
+ ZYNQMP_PM_RESET_ACPU2_PWRON,
+ ZYNQMP_PM_RESET_ACPU1_PWRON,
+ ZYNQMP_PM_RESET_ACPU0_PWRON,
+ ZYNQMP_PM_RESET_APU_L2,
+ ZYNQMP_PM_RESET_ACPU3,
+ ZYNQMP_PM_RESET_ACPU2,
+ ZYNQMP_PM_RESET_ACPU1,
+ ZYNQMP_PM_RESET_ACPU0,
+ ZYNQMP_PM_RESET_DDR,
+ ZYNQMP_PM_RESET_APM_FPD,
+ ZYNQMP_PM_RESET_SOFT,
+ ZYNQMP_PM_RESET_GEM0,
+ ZYNQMP_PM_RESET_GEM1,
+ ZYNQMP_PM_RESET_GEM2,
+ ZYNQMP_PM_RESET_GEM3,
+ ZYNQMP_PM_RESET_QSPI,
+ ZYNQMP_PM_RESET_UART0,
+ ZYNQMP_PM_RESET_UART1,
+ ZYNQMP_PM_RESET_SPI0,
+ ZYNQMP_PM_RESET_SPI1,
+ ZYNQMP_PM_RESET_SDIO0,
+ ZYNQMP_PM_RESET_SDIO1,
+ ZYNQMP_PM_RESET_CAN0,
+ ZYNQMP_PM_RESET_CAN1,
+ ZYNQMP_PM_RESET_I2C0,
+ ZYNQMP_PM_RESET_I2C1,
+ ZYNQMP_PM_RESET_TTC0,
+ ZYNQMP_PM_RESET_TTC1,
+ ZYNQMP_PM_RESET_TTC2,
+ ZYNQMP_PM_RESET_TTC3,
+ ZYNQMP_PM_RESET_SWDT_CRL,
+ ZYNQMP_PM_RESET_NAND,
+ ZYNQMP_PM_RESET_ADMA,
+ ZYNQMP_PM_RESET_GPIO,
+ ZYNQMP_PM_RESET_IOU_CC,
+ ZYNQMP_PM_RESET_TIMESTAMP,
+ ZYNQMP_PM_RESET_RPU_R50,
+ ZYNQMP_PM_RESET_RPU_R51,
+ ZYNQMP_PM_RESET_RPU_AMBA,
+ ZYNQMP_PM_RESET_OCM,
+ ZYNQMP_PM_RESET_RPU_PGE,
+ ZYNQMP_PM_RESET_USB0_CORERESET,
+ ZYNQMP_PM_RESET_USB1_CORERESET,
+ ZYNQMP_PM_RESET_USB0_HIBERRESET,
+ ZYNQMP_PM_RESET_USB1_HIBERRESET,
+ ZYNQMP_PM_RESET_USB0_APB,
+ ZYNQMP_PM_RESET_USB1_APB,
+ ZYNQMP_PM_RESET_IPI,
+ ZYNQMP_PM_RESET_APM_LPD,
+ ZYNQMP_PM_RESET_RTC,
+ ZYNQMP_PM_RESET_SYSMON,
+ ZYNQMP_PM_RESET_AFI_FM6,
+ ZYNQMP_PM_RESET_LPD_SWDT,
+ ZYNQMP_PM_RESET_FPD,
+ ZYNQMP_PM_RESET_RPU_DBG1,
+ ZYNQMP_PM_RESET_RPU_DBG0,
+ ZYNQMP_PM_RESET_DBG_LPD,
+ ZYNQMP_PM_RESET_DBG_FPD,
+ ZYNQMP_PM_RESET_APLL,
+ ZYNQMP_PM_RESET_DPLL,
+ ZYNQMP_PM_RESET_VPLL,
+ ZYNQMP_PM_RESET_IOPLL,
+ ZYNQMP_PM_RESET_RPLL,
+ ZYNQMP_PM_RESET_GPO3_PL_0,
+ ZYNQMP_PM_RESET_GPO3_PL_1,
+ ZYNQMP_PM_RESET_GPO3_PL_2,
+ ZYNQMP_PM_RESET_GPO3_PL_3,
+ ZYNQMP_PM_RESET_GPO3_PL_4,
+ ZYNQMP_PM_RESET_GPO3_PL_5,
+ ZYNQMP_PM_RESET_GPO3_PL_6,
+ ZYNQMP_PM_RESET_GPO3_PL_7,
+ ZYNQMP_PM_RESET_GPO3_PL_8,
+ ZYNQMP_PM_RESET_GPO3_PL_9,
+ ZYNQMP_PM_RESET_GPO3_PL_10,
+ ZYNQMP_PM_RESET_GPO3_PL_11,
+ ZYNQMP_PM_RESET_GPO3_PL_12,
+ ZYNQMP_PM_RESET_GPO3_PL_13,
+ ZYNQMP_PM_RESET_GPO3_PL_14,
+ ZYNQMP_PM_RESET_GPO3_PL_15,
+ ZYNQMP_PM_RESET_GPO3_PL_16,
+ ZYNQMP_PM_RESET_GPO3_PL_17,
+ ZYNQMP_PM_RESET_GPO3_PL_18,
+ ZYNQMP_PM_RESET_GPO3_PL_19,
+ ZNQMP_PM_RESET_GPO3_PL_20,
+ ZYNQMP_PM_RESET_GPO3_PL_21,
+ ZYNQMP_PM_RESET_GPO3_PL_22,
+ ZYNQMP_PM_RESET_GPO3_PL_23,
+ ZYNQMP_PM_RESET_GPO3_PL_24,
+ ZYNQMP_PM_RESET_GPO3_PL_25,
+ ZYNQMP_PM_RESET_GPO3_PL_26,
+ ZYNQMP_PM_RESET_GPO3_PL_27,
+ ZYNQMP_PM_RESET_GPO3_PL_28,
+ ZYNQMP_PM_RESET_GPO3_PL_29,
+ ZYNQMP_PM_RESET_GPO3_PL_30,
+ ZYNQMP_PM_RESET_GPO3_PL_31,
+ ZYNQMP_PM_RESET_RPU_LS,
+ ZYNQMP_PM_RESET_PS_ONLY,
+ ZYNQMP_PM_RESET_PL,
+ ZYNQMP_PM_RESET_PS_PL0,
+ ZYNQMP_PM_RESET_PS_PL1,
+ ZYNQMP_PM_RESET_PS_PL2,
+ ZYNQMP_PM_RESET_PS_PL3,
+ ZYNQMP_PM_RESET_END
+};
+
/**
* struct zynqmp_pm_query_data - PM query data
* @qid: query ID
@@ -101,6 +234,9 @@ struct zynqmp_eemi_ops {
int (*clock_getrate)(u32 clock_id, u64 *rate);
int (*clock_setparent)(u32 clock_id, u32 parent_id);
int (*clock_getparent)(u32 clock_id, u32 *parent_id);
+ int (*reset_assert)(const enum zynqmp_pm_reset reset,
+ const enum zynqmp_pm_reset_action assert_flag);
+ int (*reset_get_status)(const enum zynqmp_pm_reset reset, u32 *status);
};
#if IS_REACHABLE(CONFIG_ARCH_ZYNQMP)
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RFC PATCH v2 2/3] dt-bindings: fpga: Add bindings for ZynqMP reset driver
2018-09-05 6:40 ` Nava kishore Manne
(?)
@ 2018-09-05 6:40 ` Nava kishore Manne
-1 siblings, 0 replies; 12+ messages in thread
From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw)
To: robh+dt, mark.rutland, michal.simek, p.zabel, nava.manne, rajanv,
jollys, devicetree, linux-arm-kernel, linux-kernel
Add documentation to describe Xilinx ZynqMP reset driver
bindings.
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
---
Changes for v2:
-Moved reset node as a child to firwmare
node.
.../firmware/xilinx/xlnx,zynqmp-firmware.txt | 142 +++++++++++++++++++++
1 file changed, 142 insertions(+)
diff --git a/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt b/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt
index 1b431d9..351b1bb 100644
--- a/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt
+++ b/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt
@@ -17,6 +17,144 @@ Required properties:
- "smc" : SMC #0, following the SMCCC
- "hvc" : HVC #0, following the SMCCC
+--------------------------------------------------------------------------
+ = Zynq UltraScale+ MPSoC reset driver binding =
+--------------------------------------------------------------------------
+The Zynq UltraScale+ MPSoC has several different resets.
+
+See Chapter 36 of the Zynq UltraScale+ MPSoC TRM (UG) for more information
+about zynqmp resets.
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required Properties:
+- compatible: "xlnx,zynqmp-reset"
+- #reset-cells: Specifies the number of cells needed to encode reset
+ line, should be 1
+
+Reset outputs:
+ 0 :PCIE config reset.
+ 1 :PCIE bridge block level reset (AXI interface).
+ 2 :PCIE control block level,reset.
+ 3 :Display Port block level reset (includes DPDMA).
+ 4 :FPD WDT reset.
+ 5 :AF_FM5 block level reset.
+ 6 :AF_FM4 block level reset.
+ 7 :AF_FM3 block level reset.
+ 8 :AF_FM2 block level reset.
+ 9 :AF_FM1 block level reset.
+ 10 :AF_FM0 block level reset.
+ 11 :GDMA block level reset.
+ 12 :Pixel Processor (GPU_PP1) block level reset.
+ 13 :Pixel Processor (GPU_PP0) block level reset.
+ 14 :GPU block level reset.
+ 15 :GT block level reset.
+ 16 :Sata block level reset.
+ 17 :ACPU3 power on reset.
+ 18 :ACPU2 power on reset.
+ 19 :ACPU1 power on reset.
+ 20 :ACPU0 power on reset.
+ 21 :APU L2 reset.
+ 22 :ACPU3 reset.
+ 23 :ACPU2 reset.
+ 24 :ACPU1 reset.
+ 25 :ACPU0 reset.
+ 26 :DDR block level reset inside of the DDR Sub System.
+ 27 :APM block level reset inside of the DDR Sub System.
+ 28 :soft reset.
+ 29 :GEM 0 reset.
+ 30 :GEM 1 reset.
+ 31 :GEM 2 reset.
+ 32 :GEM 3 reset.
+ 33 :qspi reset.
+ 34 :uart0 reset.
+ 35 :uart1 reset.
+ 36 :spi0 reset.
+ 37 :spi1 reset.
+ 38 :sdio0 reset.
+ 39 :sdio1 reset.
+ 40 :can0 reset.
+ 41 :can1 reset.
+ 42 :i2c0 reset.
+ 43 :i2c1 reset.
+ 44 :ttc0 reset.
+ 45 :ttc1 reset.
+ 46 :ttc2 reset.
+ 47 :ttc3 reset.
+ 48 :swdt reset.
+ 49 :nand reset.
+ 50 :adma reset.
+ 51 :gpio reset.
+ 52 :iou_cc reset.
+ 53 :timestamp reset.
+ 54 :rpu_r50 reset.
+ 55 :rpu r51 reset.
+ 56 :rpu_amba reset.
+ 57 :ocm reset.
+ 58 :rpu_pge reset.
+ 59 :usb0_core reset.
+ 60 :usb1_core reset.
+ 61 :usb0_hiber reset.
+ 62 :usb1_hiber reset.
+ 63 :usb0_apb reset.
+ 64 :usb1_apb reset.
+ 65 :ipi reset.
+ 66 :apm reset.
+ 67 :rtc reset.
+ 68 :sysmon reset.
+ 69 :afi_fm6 reset.
+ 70 :lpd_swdt reset.
+ 71 :fpd_reset.
+ 72 :rpu_dbg1 reset.
+ 73 :rpu_dbg0 reset.
+ 74 :dbg_lpd reset.
+ 75 :dbg_fpd reset.
+ 76 :apll reset.
+ 77 :dpll reset.
+ 78 :vpll reset.
+ 79 :iopll reset.
+ 80 :rpll reset.
+ 81 :gpio_pl_0 reset.
+ 82 :gpio_pl_1 reset.
+ 83 :gpio_pl_2 reset.
+ 84 :gpio_pl_3 reset.
+ 85 :gpio_pl_4 reset.
+ 86 :gpio_pl_5 reset.
+ 87 :gpio_pl_6 reset.
+ 88 :gpio_pl_7 reset.
+ 89 :gpio_pl_8 reset.
+ 90 :gpio_pl_9 reset.
+ 91 :gpio_pl_10 reset.
+ 92 :gpio_pl_11 reset.
+ 93 :gpio_pl_12 reset.
+ 94 :gpio_pl_13 reset.
+ 95 :gpio_pl_14 reset.
+ 96 :gpio_pl_15 reset.
+ 97 :gpio_pl_16 reset.
+ 98 :gpio_pl_17 reset.
+ 99 :gpio_pl_18 reset.
+ 100 :gpio_pl_19 reset.
+ 101 :gpio_pl_20 reset.
+ 102 :gpio_pl_21 reset.
+ 103 :gpio_pl_22 reset.
+ 104 :gpio_pl_23 reset.
+ 105 :gpio_pl_24 reset.
+ 106 :gpio_pl_25 reset.
+ 107 :gpio_pl_26 reset.
+ 108 :gpio_pl_27 reset.
+ 109 :gpio_pl_28 reset.
+ 110 :gpio_pl_29 reset.
+ 111 :gpio_pl_30 reset.
+ 112 :gpio_pl_31 reset.
+ 113 :rpu_ls reset.
+ 114 :ps_only reset.
+ 115 :pl reset.
+ 116 :ps_pl0 reset
+ 117 :ps_pl1 reset
+ 118 :ps_pl2 reset
+ 119 :ps_pl3 reset
+
-------
Example
-------
@@ -25,5 +163,9 @@ firmware {
zynqmp_firmware: zynqmp-firmware {
compatible = "xlnx,zynqmp-firmware";
method = "smc";
+ reset-controller:reset-controller@0 {
+ compatible = "xlnx,zynqmp-reset";
+ #reset-cells = <1>;
+ };
};
};
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RFC PATCH v2 2/3] dt-bindings: fpga: Add bindings for ZynqMP reset driver
@ 2018-09-05 6:40 ` Nava kishore Manne
0 siblings, 0 replies; 12+ messages in thread
From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw)
To: robh+dt, mark.rutland, michal.simek, p.zabel, nava.manne, rajanv,
jollys, devicetree, linux-arm-kernel, linux-kernel
Add documentation to describe Xilinx ZynqMP reset driver
bindings.
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
---
Changes for v2:
-Moved reset node as a child to firwmare
node.
.../firmware/xilinx/xlnx,zynqmp-firmware.txt | 142 +++++++++++++++++++++
1 file changed, 142 insertions(+)
diff --git a/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt b/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt
index 1b431d9..351b1bb 100644
--- a/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt
+++ b/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt
@@ -17,6 +17,144 @@ Required properties:
- "smc" : SMC #0, following the SMCCC
- "hvc" : HVC #0, following the SMCCC
+--------------------------------------------------------------------------
+ = Zynq UltraScale+ MPSoC reset driver binding =
+--------------------------------------------------------------------------
+The Zynq UltraScale+ MPSoC has several different resets.
+
+See Chapter 36 of the Zynq UltraScale+ MPSoC TRM (UG) for more information
+about zynqmp resets.
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required Properties:
+- compatible: "xlnx,zynqmp-reset"
+- #reset-cells: Specifies the number of cells needed to encode reset
+ line, should be 1
+
+Reset outputs:
+ 0 :PCIE config reset.
+ 1 :PCIE bridge block level reset (AXI interface).
+ 2 :PCIE control block level,reset.
+ 3 :Display Port block level reset (includes DPDMA).
+ 4 :FPD WDT reset.
+ 5 :AF_FM5 block level reset.
+ 6 :AF_FM4 block level reset.
+ 7 :AF_FM3 block level reset.
+ 8 :AF_FM2 block level reset.
+ 9 :AF_FM1 block level reset.
+ 10 :AF_FM0 block level reset.
+ 11 :GDMA block level reset.
+ 12 :Pixel Processor (GPU_PP1) block level reset.
+ 13 :Pixel Processor (GPU_PP0) block level reset.
+ 14 :GPU block level reset.
+ 15 :GT block level reset.
+ 16 :Sata block level reset.
+ 17 :ACPU3 power on reset.
+ 18 :ACPU2 power on reset.
+ 19 :ACPU1 power on reset.
+ 20 :ACPU0 power on reset.
+ 21 :APU L2 reset.
+ 22 :ACPU3 reset.
+ 23 :ACPU2 reset.
+ 24 :ACPU1 reset.
+ 25 :ACPU0 reset.
+ 26 :DDR block level reset inside of the DDR Sub System.
+ 27 :APM block level reset inside of the DDR Sub System.
+ 28 :soft reset.
+ 29 :GEM 0 reset.
+ 30 :GEM 1 reset.
+ 31 :GEM 2 reset.
+ 32 :GEM 3 reset.
+ 33 :qspi reset.
+ 34 :uart0 reset.
+ 35 :uart1 reset.
+ 36 :spi0 reset.
+ 37 :spi1 reset.
+ 38 :sdio0 reset.
+ 39 :sdio1 reset.
+ 40 :can0 reset.
+ 41 :can1 reset.
+ 42 :i2c0 reset.
+ 43 :i2c1 reset.
+ 44 :ttc0 reset.
+ 45 :ttc1 reset.
+ 46 :ttc2 reset.
+ 47 :ttc3 reset.
+ 48 :swdt reset.
+ 49 :nand reset.
+ 50 :adma reset.
+ 51 :gpio reset.
+ 52 :iou_cc reset.
+ 53 :timestamp reset.
+ 54 :rpu_r50 reset.
+ 55 :rpu r51 reset.
+ 56 :rpu_amba reset.
+ 57 :ocm reset.
+ 58 :rpu_pge reset.
+ 59 :usb0_core reset.
+ 60 :usb1_core reset.
+ 61 :usb0_hiber reset.
+ 62 :usb1_hiber reset.
+ 63 :usb0_apb reset.
+ 64 :usb1_apb reset.
+ 65 :ipi reset.
+ 66 :apm reset.
+ 67 :rtc reset.
+ 68 :sysmon reset.
+ 69 :afi_fm6 reset.
+ 70 :lpd_swdt reset.
+ 71 :fpd_reset.
+ 72 :rpu_dbg1 reset.
+ 73 :rpu_dbg0 reset.
+ 74 :dbg_lpd reset.
+ 75 :dbg_fpd reset.
+ 76 :apll reset.
+ 77 :dpll reset.
+ 78 :vpll reset.
+ 79 :iopll reset.
+ 80 :rpll reset.
+ 81 :gpio_pl_0 reset.
+ 82 :gpio_pl_1 reset.
+ 83 :gpio_pl_2 reset.
+ 84 :gpio_pl_3 reset.
+ 85 :gpio_pl_4 reset.
+ 86 :gpio_pl_5 reset.
+ 87 :gpio_pl_6 reset.
+ 88 :gpio_pl_7 reset.
+ 89 :gpio_pl_8 reset.
+ 90 :gpio_pl_9 reset.
+ 91 :gpio_pl_10 reset.
+ 92 :gpio_pl_11 reset.
+ 93 :gpio_pl_12 reset.
+ 94 :gpio_pl_13 reset.
+ 95 :gpio_pl_14 reset.
+ 96 :gpio_pl_15 reset.
+ 97 :gpio_pl_16 reset.
+ 98 :gpio_pl_17 reset.
+ 99 :gpio_pl_18 reset.
+ 100 :gpio_pl_19 reset.
+ 101 :gpio_pl_20 reset.
+ 102 :gpio_pl_21 reset.
+ 103 :gpio_pl_22 reset.
+ 104 :gpio_pl_23 reset.
+ 105 :gpio_pl_24 reset.
+ 106 :gpio_pl_25 reset.
+ 107 :gpio_pl_26 reset.
+ 108 :gpio_pl_27 reset.
+ 109 :gpio_pl_28 reset.
+ 110 :gpio_pl_29 reset.
+ 111 :gpio_pl_30 reset.
+ 112 :gpio_pl_31 reset.
+ 113 :rpu_ls reset.
+ 114 :ps_only reset.
+ 115 :pl reset.
+ 116 :ps_pl0 reset
+ 117 :ps_pl1 reset
+ 118 :ps_pl2 reset
+ 119 :ps_pl3 reset
+
-------
Example
-------
@@ -25,5 +163,9 @@ firmware {
zynqmp_firmware: zynqmp-firmware {
compatible = "xlnx,zynqmp-firmware";
method = "smc";
+ reset-controller:reset-controller@0 {
+ compatible = "xlnx,zynqmp-reset";
+ #reset-cells = <1>;
+ };
};
};
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RFC PATCH v2 2/3] dt-bindings: fpga: Add bindings for ZynqMP reset driver
@ 2018-09-05 6:40 ` Nava kishore Manne
0 siblings, 0 replies; 12+ messages in thread
From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw)
To: linux-arm-kernel
Add documentation to describe Xilinx ZynqMP reset driver
bindings.
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
---
Changes for v2:
-Moved reset node as a child to firwmare
node.
.../firmware/xilinx/xlnx,zynqmp-firmware.txt | 142 +++++++++++++++++++++
1 file changed, 142 insertions(+)
diff --git a/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt b/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt
index 1b431d9..351b1bb 100644
--- a/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt
+++ b/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt
@@ -17,6 +17,144 @@ Required properties:
- "smc" : SMC #0, following the SMCCC
- "hvc" : HVC #0, following the SMCCC
+--------------------------------------------------------------------------
+ = Zynq UltraScale+ MPSoC reset driver binding =
+--------------------------------------------------------------------------
+The Zynq UltraScale+ MPSoC has several different resets.
+
+See Chapter 36 of the Zynq UltraScale+ MPSoC TRM (UG) for more information
+about zynqmp resets.
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required Properties:
+- compatible: "xlnx,zynqmp-reset"
+- #reset-cells: Specifies the number of cells needed to encode reset
+ line, should be 1
+
+Reset outputs:
+ 0 :PCIE config reset.
+ 1 :PCIE bridge block level reset (AXI interface).
+ 2 :PCIE control block level,reset.
+ 3 :Display Port block level reset (includes DPDMA).
+ 4 :FPD WDT reset.
+ 5 :AF_FM5 block level reset.
+ 6 :AF_FM4 block level reset.
+ 7 :AF_FM3 block level reset.
+ 8 :AF_FM2 block level reset.
+ 9 :AF_FM1 block level reset.
+ 10 :AF_FM0 block level reset.
+ 11 :GDMA block level reset.
+ 12 :Pixel Processor (GPU_PP1) block level reset.
+ 13 :Pixel Processor (GPU_PP0) block level reset.
+ 14 :GPU block level reset.
+ 15 :GT block level reset.
+ 16 :Sata block level reset.
+ 17 :ACPU3 power on reset.
+ 18 :ACPU2 power on reset.
+ 19 :ACPU1 power on reset.
+ 20 :ACPU0 power on reset.
+ 21 :APU L2 reset.
+ 22 :ACPU3 reset.
+ 23 :ACPU2 reset.
+ 24 :ACPU1 reset.
+ 25 :ACPU0 reset.
+ 26 :DDR block level reset inside of the DDR Sub System.
+ 27 :APM block level reset inside of the DDR Sub System.
+ 28 :soft reset.
+ 29 :GEM 0 reset.
+ 30 :GEM 1 reset.
+ 31 :GEM 2 reset.
+ 32 :GEM 3 reset.
+ 33 :qspi reset.
+ 34 :uart0 reset.
+ 35 :uart1 reset.
+ 36 :spi0 reset.
+ 37 :spi1 reset.
+ 38 :sdio0 reset.
+ 39 :sdio1 reset.
+ 40 :can0 reset.
+ 41 :can1 reset.
+ 42 :i2c0 reset.
+ 43 :i2c1 reset.
+ 44 :ttc0 reset.
+ 45 :ttc1 reset.
+ 46 :ttc2 reset.
+ 47 :ttc3 reset.
+ 48 :swdt reset.
+ 49 :nand reset.
+ 50 :adma reset.
+ 51 :gpio reset.
+ 52 :iou_cc reset.
+ 53 :timestamp reset.
+ 54 :rpu_r50 reset.
+ 55 :rpu r51 reset.
+ 56 :rpu_amba reset.
+ 57 :ocm reset.
+ 58 :rpu_pge reset.
+ 59 :usb0_core reset.
+ 60 :usb1_core reset.
+ 61 :usb0_hiber reset.
+ 62 :usb1_hiber reset.
+ 63 :usb0_apb reset.
+ 64 :usb1_apb reset.
+ 65 :ipi reset.
+ 66 :apm reset.
+ 67 :rtc reset.
+ 68 :sysmon reset.
+ 69 :afi_fm6 reset.
+ 70 :lpd_swdt reset.
+ 71 :fpd_reset.
+ 72 :rpu_dbg1 reset.
+ 73 :rpu_dbg0 reset.
+ 74 :dbg_lpd reset.
+ 75 :dbg_fpd reset.
+ 76 :apll reset.
+ 77 :dpll reset.
+ 78 :vpll reset.
+ 79 :iopll reset.
+ 80 :rpll reset.
+ 81 :gpio_pl_0 reset.
+ 82 :gpio_pl_1 reset.
+ 83 :gpio_pl_2 reset.
+ 84 :gpio_pl_3 reset.
+ 85 :gpio_pl_4 reset.
+ 86 :gpio_pl_5 reset.
+ 87 :gpio_pl_6 reset.
+ 88 :gpio_pl_7 reset.
+ 89 :gpio_pl_8 reset.
+ 90 :gpio_pl_9 reset.
+ 91 :gpio_pl_10 reset.
+ 92 :gpio_pl_11 reset.
+ 93 :gpio_pl_12 reset.
+ 94 :gpio_pl_13 reset.
+ 95 :gpio_pl_14 reset.
+ 96 :gpio_pl_15 reset.
+ 97 :gpio_pl_16 reset.
+ 98 :gpio_pl_17 reset.
+ 99 :gpio_pl_18 reset.
+ 100 :gpio_pl_19 reset.
+ 101 :gpio_pl_20 reset.
+ 102 :gpio_pl_21 reset.
+ 103 :gpio_pl_22 reset.
+ 104 :gpio_pl_23 reset.
+ 105 :gpio_pl_24 reset.
+ 106 :gpio_pl_25 reset.
+ 107 :gpio_pl_26 reset.
+ 108 :gpio_pl_27 reset.
+ 109 :gpio_pl_28 reset.
+ 110 :gpio_pl_29 reset.
+ 111 :gpio_pl_30 reset.
+ 112 :gpio_pl_31 reset.
+ 113 :rpu_ls reset.
+ 114 :ps_only reset.
+ 115 :pl reset.
+ 116 :ps_pl0 reset
+ 117 :ps_pl1 reset
+ 118 :ps_pl2 reset
+ 119 :ps_pl3 reset
+
-------
Example
-------
@@ -25,5 +163,9 @@ firmware {
zynqmp_firmware: zynqmp-firmware {
compatible = "xlnx,zynqmp-firmware";
method = "smc";
+ reset-controller:reset-controller at 0 {
+ compatible = "xlnx,zynqmp-reset";
+ #reset-cells = <1>;
+ };
};
};
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RFC PATCH v2 3/3] reset: reset-zynqmp: Adding support for Xilinx zynqmp reset controller.
2018-09-05 6:40 ` Nava kishore Manne
(?)
@ 2018-09-05 6:40 ` Nava kishore Manne
-1 siblings, 0 replies; 12+ messages in thread
From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw)
To: robh+dt, mark.rutland, michal.simek, p.zabel, nava.manne, rajanv,
jollys, devicetree, linux-arm-kernel, linux-kernel
Add a reset controller driver for Xilinx Zynq UltraScale+ MPSoC.
The zynqmp reset-controller has the ability to reset lines
connected to different blocks and peripheral in the Soc.
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
---
Changes for v2:
-Moved eemi_ops into a priv struct as suggested
by philipp.
drivers/reset/Makefile | 1 +
drivers/reset/reset-zynqmp.c | 115 +++++++++++++++++++++++++++++++++++++++++++
2 files changed, 116 insertions(+)
create mode 100644 drivers/reset/reset-zynqmp.c
diff --git a/drivers/reset/Makefile b/drivers/reset/Makefile
index c1261dc..27e4a33 100644
--- a/drivers/reset/Makefile
+++ b/drivers/reset/Makefile
@@ -21,4 +21,5 @@ obj-$(CONFIG_RESET_TI_SCI) += reset-ti-sci.o
obj-$(CONFIG_RESET_TI_SYSCON) += reset-ti-syscon.o
obj-$(CONFIG_RESET_UNIPHIER) += reset-uniphier.o
obj-$(CONFIG_RESET_ZYNQ) += reset-zynq.o
+obj-$(CONFIG_ARCH_ZYNQMP) += reset-zynqmp.o
diff --git a/drivers/reset/reset-zynqmp.c b/drivers/reset/reset-zynqmp.c
new file mode 100644
index 0000000..f908492
--- /dev/null
+++ b/drivers/reset/reset-zynqmp.c
@@ -0,0 +1,115 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ */
+
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/reset-controller.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+
+#define ZYNQMP_NR_RESETS (ZYNQMP_PM_RESET_END - ZYNQMP_PM_RESET_START - 2)
+#define ZYNQMP_RESET_ID (ZYNQMP_PM_RESET_START + 1)
+
+struct zynqmp_reset_data {
+ struct reset_controller_dev rcdev;
+ const struct zynqmp_eemi_ops *eemi_ops;
+};
+
+static inline struct zynqmp_reset_data *
+to_zynqmp_reset_data(struct reset_controller_dev *rcdev)
+{
+ return container_of(rcdev, struct zynqmp_reset_data, rcdev);
+}
+
+static int zynqmp_reset_assert(struct reset_controller_dev *rcdev,
+ unsigned long id)
+{
+ struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev);
+
+ return priv->eemi_ops->reset_assert(ZYNQMP_RESET_ID + id,
+ PM_RESET_ACTION_ASSERT);
+}
+
+static int zynqmp_reset_deassert(struct reset_controller_dev *rcdev,
+ unsigned long id)
+{
+ struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev);
+
+ return priv->eemi_ops->reset_assert(ZYNQMP_RESET_ID + id,
+ PM_RESET_ACTION_RELEASE);
+}
+
+static int zynqmp_reset_status(struct reset_controller_dev *rcdev,
+ unsigned long id)
+{
+ struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev);
+ int val, err;
+
+ err = priv->eemi_ops->reset_get_status(ZYNQMP_RESET_ID + id, &val);
+ if (!err)
+ return -EINVAL;
+
+ return val;
+}
+
+static int zynqmp_reset_reset(struct reset_controller_dev *rcdev,
+ unsigned long id)
+{
+ struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev);
+
+ return priv->eemi_ops->reset_assert(ZYNQMP_RESET_ID + id,
+ PM_RESET_ACTION_PULSE);
+}
+
+static struct reset_control_ops zynqmp_reset_ops = {
+ .reset = zynqmp_reset_reset,
+ .assert = zynqmp_reset_assert,
+ .deassert = zynqmp_reset_deassert,
+ .status = zynqmp_reset_status,
+};
+
+static int zynqmp_reset_probe(struct platform_device *pdev)
+{
+ struct zynqmp_reset_data *priv;
+
+ priv = devm_kzalloc(&pdev->dev,
+ sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, priv);
+
+ priv->eemi_ops = zynqmp_pm_get_eemi_ops();
+ if (!priv->eemi_ops)
+ return -ENXIO;
+
+ priv->rcdev.ops = &zynqmp_reset_ops;
+ priv->rcdev.owner = THIS_MODULE;
+ priv->rcdev.of_node = pdev->dev.of_node;
+ priv->rcdev.nr_resets = ZYNQMP_NR_RESETS;
+
+ return devm_reset_controller_register(&pdev->dev, &priv->rcdev);
+}
+
+static const struct of_device_id zynqmp_reset_dt_ids[] = {
+ { .compatible = "xlnx,zynqmp-reset", },
+ { },
+};
+
+static struct platform_driver zynqmp_reset_driver = {
+ .probe = zynqmp_reset_probe,
+ .driver = {
+ .name = KBUILD_MODNAME,
+ .of_match_table = zynqmp_reset_dt_ids,
+ },
+};
+
+static int __init zynqmp_reset_init(void)
+{
+ return platform_driver_register(&zynqmp_reset_driver);
+}
+
+arch_initcall(zynqmp_reset_init);
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RFC PATCH v2 3/3] reset: reset-zynqmp: Adding support for Xilinx zynqmp reset controller.
@ 2018-09-05 6:40 ` Nava kishore Manne
0 siblings, 0 replies; 12+ messages in thread
From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw)
To: robh+dt, mark.rutland, michal.simek, p.zabel, nava.manne, rajanv,
jollys, devicetree, linux-arm-kernel, linux-kernel
Add a reset controller driver for Xilinx Zynq UltraScale+ MPSoC.
The zynqmp reset-controller has the ability to reset lines
connected to different blocks and peripheral in the Soc.
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
---
Changes for v2:
-Moved eemi_ops into a priv struct as suggested
by philipp.
drivers/reset/Makefile | 1 +
drivers/reset/reset-zynqmp.c | 115 +++++++++++++++++++++++++++++++++++++++++++
2 files changed, 116 insertions(+)
create mode 100644 drivers/reset/reset-zynqmp.c
diff --git a/drivers/reset/Makefile b/drivers/reset/Makefile
index c1261dc..27e4a33 100644
--- a/drivers/reset/Makefile
+++ b/drivers/reset/Makefile
@@ -21,4 +21,5 @@ obj-$(CONFIG_RESET_TI_SCI) += reset-ti-sci.o
obj-$(CONFIG_RESET_TI_SYSCON) += reset-ti-syscon.o
obj-$(CONFIG_RESET_UNIPHIER) += reset-uniphier.o
obj-$(CONFIG_RESET_ZYNQ) += reset-zynq.o
+obj-$(CONFIG_ARCH_ZYNQMP) += reset-zynqmp.o
diff --git a/drivers/reset/reset-zynqmp.c b/drivers/reset/reset-zynqmp.c
new file mode 100644
index 0000000..f908492
--- /dev/null
+++ b/drivers/reset/reset-zynqmp.c
@@ -0,0 +1,115 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ */
+
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/reset-controller.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+
+#define ZYNQMP_NR_RESETS (ZYNQMP_PM_RESET_END - ZYNQMP_PM_RESET_START - 2)
+#define ZYNQMP_RESET_ID (ZYNQMP_PM_RESET_START + 1)
+
+struct zynqmp_reset_data {
+ struct reset_controller_dev rcdev;
+ const struct zynqmp_eemi_ops *eemi_ops;
+};
+
+static inline struct zynqmp_reset_data *
+to_zynqmp_reset_data(struct reset_controller_dev *rcdev)
+{
+ return container_of(rcdev, struct zynqmp_reset_data, rcdev);
+}
+
+static int zynqmp_reset_assert(struct reset_controller_dev *rcdev,
+ unsigned long id)
+{
+ struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev);
+
+ return priv->eemi_ops->reset_assert(ZYNQMP_RESET_ID + id,
+ PM_RESET_ACTION_ASSERT);
+}
+
+static int zynqmp_reset_deassert(struct reset_controller_dev *rcdev,
+ unsigned long id)
+{
+ struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev);
+
+ return priv->eemi_ops->reset_assert(ZYNQMP_RESET_ID + id,
+ PM_RESET_ACTION_RELEASE);
+}
+
+static int zynqmp_reset_status(struct reset_controller_dev *rcdev,
+ unsigned long id)
+{
+ struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev);
+ int val, err;
+
+ err = priv->eemi_ops->reset_get_status(ZYNQMP_RESET_ID + id, &val);
+ if (!err)
+ return -EINVAL;
+
+ return val;
+}
+
+static int zynqmp_reset_reset(struct reset_controller_dev *rcdev,
+ unsigned long id)
+{
+ struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev);
+
+ return priv->eemi_ops->reset_assert(ZYNQMP_RESET_ID + id,
+ PM_RESET_ACTION_PULSE);
+}
+
+static struct reset_control_ops zynqmp_reset_ops = {
+ .reset = zynqmp_reset_reset,
+ .assert = zynqmp_reset_assert,
+ .deassert = zynqmp_reset_deassert,
+ .status = zynqmp_reset_status,
+};
+
+static int zynqmp_reset_probe(struct platform_device *pdev)
+{
+ struct zynqmp_reset_data *priv;
+
+ priv = devm_kzalloc(&pdev->dev,
+ sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, priv);
+
+ priv->eemi_ops = zynqmp_pm_get_eemi_ops();
+ if (!priv->eemi_ops)
+ return -ENXIO;
+
+ priv->rcdev.ops = &zynqmp_reset_ops;
+ priv->rcdev.owner = THIS_MODULE;
+ priv->rcdev.of_node = pdev->dev.of_node;
+ priv->rcdev.nr_resets = ZYNQMP_NR_RESETS;
+
+ return devm_reset_controller_register(&pdev->dev, &priv->rcdev);
+}
+
+static const struct of_device_id zynqmp_reset_dt_ids[] = {
+ { .compatible = "xlnx,zynqmp-reset", },
+ { },
+};
+
+static struct platform_driver zynqmp_reset_driver = {
+ .probe = zynqmp_reset_probe,
+ .driver = {
+ .name = KBUILD_MODNAME,
+ .of_match_table = zynqmp_reset_dt_ids,
+ },
+};
+
+static int __init zynqmp_reset_init(void)
+{
+ return platform_driver_register(&zynqmp_reset_driver);
+}
+
+arch_initcall(zynqmp_reset_init);
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RFC PATCH v2 3/3] reset: reset-zynqmp: Adding support for Xilinx zynqmp reset controller.
@ 2018-09-05 6:40 ` Nava kishore Manne
0 siblings, 0 replies; 12+ messages in thread
From: Nava kishore Manne @ 2018-09-05 6:40 UTC (permalink / raw)
To: linux-arm-kernel
Add a reset controller driver for Xilinx Zynq UltraScale+ MPSoC.
The zynqmp reset-controller has the ability to reset lines
connected to different blocks and peripheral in the Soc.
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
---
Changes for v2:
-Moved eemi_ops into a priv struct as suggested
by philipp.
drivers/reset/Makefile | 1 +
drivers/reset/reset-zynqmp.c | 115 +++++++++++++++++++++++++++++++++++++++++++
2 files changed, 116 insertions(+)
create mode 100644 drivers/reset/reset-zynqmp.c
diff --git a/drivers/reset/Makefile b/drivers/reset/Makefile
index c1261dc..27e4a33 100644
--- a/drivers/reset/Makefile
+++ b/drivers/reset/Makefile
@@ -21,4 +21,5 @@ obj-$(CONFIG_RESET_TI_SCI) += reset-ti-sci.o
obj-$(CONFIG_RESET_TI_SYSCON) += reset-ti-syscon.o
obj-$(CONFIG_RESET_UNIPHIER) += reset-uniphier.o
obj-$(CONFIG_RESET_ZYNQ) += reset-zynq.o
+obj-$(CONFIG_ARCH_ZYNQMP) += reset-zynqmp.o
diff --git a/drivers/reset/reset-zynqmp.c b/drivers/reset/reset-zynqmp.c
new file mode 100644
index 0000000..f908492
--- /dev/null
+++ b/drivers/reset/reset-zynqmp.c
@@ -0,0 +1,115 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ */
+
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/reset-controller.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+
+#define ZYNQMP_NR_RESETS (ZYNQMP_PM_RESET_END - ZYNQMP_PM_RESET_START - 2)
+#define ZYNQMP_RESET_ID (ZYNQMP_PM_RESET_START + 1)
+
+struct zynqmp_reset_data {
+ struct reset_controller_dev rcdev;
+ const struct zynqmp_eemi_ops *eemi_ops;
+};
+
+static inline struct zynqmp_reset_data *
+to_zynqmp_reset_data(struct reset_controller_dev *rcdev)
+{
+ return container_of(rcdev, struct zynqmp_reset_data, rcdev);
+}
+
+static int zynqmp_reset_assert(struct reset_controller_dev *rcdev,
+ unsigned long id)
+{
+ struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev);
+
+ return priv->eemi_ops->reset_assert(ZYNQMP_RESET_ID + id,
+ PM_RESET_ACTION_ASSERT);
+}
+
+static int zynqmp_reset_deassert(struct reset_controller_dev *rcdev,
+ unsigned long id)
+{
+ struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev);
+
+ return priv->eemi_ops->reset_assert(ZYNQMP_RESET_ID + id,
+ PM_RESET_ACTION_RELEASE);
+}
+
+static int zynqmp_reset_status(struct reset_controller_dev *rcdev,
+ unsigned long id)
+{
+ struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev);
+ int val, err;
+
+ err = priv->eemi_ops->reset_get_status(ZYNQMP_RESET_ID + id, &val);
+ if (!err)
+ return -EINVAL;
+
+ return val;
+}
+
+static int zynqmp_reset_reset(struct reset_controller_dev *rcdev,
+ unsigned long id)
+{
+ struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev);
+
+ return priv->eemi_ops->reset_assert(ZYNQMP_RESET_ID + id,
+ PM_RESET_ACTION_PULSE);
+}
+
+static struct reset_control_ops zynqmp_reset_ops = {
+ .reset = zynqmp_reset_reset,
+ .assert = zynqmp_reset_assert,
+ .deassert = zynqmp_reset_deassert,
+ .status = zynqmp_reset_status,
+};
+
+static int zynqmp_reset_probe(struct platform_device *pdev)
+{
+ struct zynqmp_reset_data *priv;
+
+ priv = devm_kzalloc(&pdev->dev,
+ sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, priv);
+
+ priv->eemi_ops = zynqmp_pm_get_eemi_ops();
+ if (!priv->eemi_ops)
+ return -ENXIO;
+
+ priv->rcdev.ops = &zynqmp_reset_ops;
+ priv->rcdev.owner = THIS_MODULE;
+ priv->rcdev.of_node = pdev->dev.of_node;
+ priv->rcdev.nr_resets = ZYNQMP_NR_RESETS;
+
+ return devm_reset_controller_register(&pdev->dev, &priv->rcdev);
+}
+
+static const struct of_device_id zynqmp_reset_dt_ids[] = {
+ { .compatible = "xlnx,zynqmp-reset", },
+ { },
+};
+
+static struct platform_driver zynqmp_reset_driver = {
+ .probe = zynqmp_reset_probe,
+ .driver = {
+ .name = KBUILD_MODNAME,
+ .of_match_table = zynqmp_reset_dt_ids,
+ },
+};
+
+static int __init zynqmp_reset_init(void)
+{
+ return platform_driver_register(&zynqmp_reset_driver);
+}
+
+arch_initcall(zynqmp_reset_init);
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
end of thread, other threads:[~2018-09-05 6:42 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-09-05 6:40 [RFC PATCH v2 0/3] Add reset driver support for ZynqMP Nava kishore Manne
2018-09-05 6:40 ` Nava kishore Manne
2018-09-05 6:40 ` Nava kishore Manne
2018-09-05 6:40 ` [RFC PATCH v2 1/3] firmware: xilinx: Add reset API's Nava kishore Manne
2018-09-05 6:40 ` Nava kishore Manne
2018-09-05 6:40 ` Nava kishore Manne
2018-09-05 6:40 ` [RFC PATCH v2 2/3] dt-bindings: fpga: Add bindings for ZynqMP reset driver Nava kishore Manne
2018-09-05 6:40 ` Nava kishore Manne
2018-09-05 6:40 ` Nava kishore Manne
2018-09-05 6:40 ` [RFC PATCH v2 3/3] reset: reset-zynqmp: Adding support for Xilinx zynqmp reset controller Nava kishore Manne
2018-09-05 6:40 ` Nava kishore Manne
2018-09-05 6:40 ` Nava kishore Manne
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.