Re: multiple separate pci bridges ...

[Sven Luther <sven.luther@wanadoo.fr>]

On Sun, Jan 04, 2004 at 11:06:08PM +0100, Sven Luther wrote:
>
> On Mon, Jan 05, 2004 at 08:45:24AM +1100, Benjamin Herrenschmidt wrote:
> >
> >
> > > PCI: Probing PCI hardware
> > > Scanning bus 00
> > > Found 00:00 [11ab/6460] 000600 00
> > > Found 00:08 [1106/3044] 000c00 00
> > > Found 00:28 [1000/0001] 000100 00
> > > Found 00:60 [1106/8231] 000601 00
> > > Found 00:61 [1106/0571] 000101 00
> > > Found 00:62 [1106/3038] 000c03 00
> > > Found 00:63 [1106/3038] 000c03 00
> > > Found 00:64 [1106/8235] 000000 00
> > > Found 00:65 [1106/3058] 000401 00
> > > Found 00:66 [1106/3068] 000780 00
> > > Found 00:68 [1106/3065] 000200 00
> > > Fixups for bus 00
> > > Bus scan for 00 returning with max=00
> > > Scanning bus 10
> > > Fixups for bus 10
> > > Bus scan for 10 returning with max=10
> > > PCI: Cannot allocate resource region 4 of device 00:00.0
> > >
> > > So, the 0x10 incrementation is fine, but the agp bus is not working
> > > correctly, and thus the agp graphic card not recognized (and thus no
> > > radeonfb).
> > >
> > > That said, i believe the 00:00.0 (should that not be 10:00.0 because of
> > > the renumbering) is the Marvell Discovery II pci controller, and the
> > > actual agp card should be found just behind.
> >
> > What video card is this ?
>
> A Radeon 9200 SE 64M, from Xpert Vision. The kernel is patched for
> Radeon 9200 SE support. (Both i have are Yd models).

Ok, i got it to work finally, at least upto asking me for a root
filesystem, which i don't yet have on this harddisk.

Now, I have some technical questions about how to best do a few things.

I was recommended to set the ppc_md.pci_exclude_device so that the
device 0 (the marvell bridge itself) is not seen by linux. I did this by
following the 4xx example, which should be ok.

But, i have to do access some address which i need to ioremap. I created
a hose->cfg_peg2_magic to to put this ioremapped address in. I guess
this is not the most clean way of doing this or something, any hint on
how to best do it ? I need to set this in chrp_find_bridges or something
such, and use the address in the read/write_config functions.

Also, i had to manually set hose->bus_offset = 0x10, since that didn't
seem to be set automatically. I don't know why though.

And finally, about the stuff which blocked me most, i am somewhat
bewildered. I use this :

        data = 0x80000000 | ((dev->bus->number - hose->bus_offset) << 16)
		| (dev->devfn << 8) | (offset & 0xff);

As the address to write to, but the indirect pci stuff uses offset &
0xfc, which blanks bits 0 & 1 for pci config type selection. What am i
misunderstanding or doing wrong here ?

A, and a last question to Rob Baxter, did you manage to get the builtin
gigabyte ethernet port to work, and if yes, with which code, an
existing driver or some home built driver. Can you eventually share the
code or something such ?

Anyway, thanks for your help.

Friendly,

Sven Luther


** Sent via the linuxppc-dev mail list. See http://lists.linuxppc.org/