[U-Boot] 83xx: add support for ve8313 board

[U-Boot] 83xx: add support for ve8313 board

[Heiko Schocher]

This patch add support for the ve8313 board based on
Freescale MPC8313 CPU.

- serial console on UART 1
- 128 MB DDR RAM
- 32 MB NOR Flash
- 16 MB NAND Flash
- Ethernet MII Mode on TSEC0
- micrel ksz804 phy
- Hardware WDT MAX824

Signed-off-by: Heiko Schocher <hs@denx.de>
---
 board/ve8313/Makefile    |   50 +++++
 board/ve8313/config.mk   |   10 +
 board/ve8313/ve8313.c    |  212 ++++++++++++++++++
 boards.cfg               |    1 +
 include/configs/ve8313.h |  534 ++++++++++++++++++++++++++++++++++++++++++++++
 5 files changed, 807 insertions(+), 0 deletions(-)
 create mode 100644 board/ve8313/Makefile
 create mode 100644 board/ve8313/config.mk
 create mode 100644 board/ve8313/ve8313.c
 create mode 100644 include/configs/ve8313.h

diff --git a/board/ve8313/Makefile b/board/ve8313/Makefile
new file mode 100644
index 0000000..c95f90e
--- /dev/null
+++ b/board/ve8313/Makefile
@@ -0,0 +1,50 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	:= $(BOARD).o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/ve8313/config.mk b/board/ve8313/config.mk
new file mode 100644
index 0000000..66fbc10
--- /dev/null
+++ b/board/ve8313/config.mk
@@ -0,0 +1,10 @@
+ifndef NAND_SPL
+sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp
+endif
+
+ifndef TEXT_BASE
+#TEXT_BASE = 0x100000
+TEXT_BASE = 0xfe000000
+endif
+
+#PLATFORM_CPPFLAGS += -DDEBUG
diff --git a/board/ve8313/ve8313.c b/board/ve8313/ve8313.c
new file mode 100644
index 0000000..b13d1f3
--- /dev/null
+++ b/board/ve8313/ve8313.c
@@ -0,0 +1,212 @@
+/*
+ * (C) Copyright 2010
+ * Heiko Schocher, DENX Software Engineering, hs at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#if defined(CONFIG_OF_LIBFDT)
+#include <libfdt.h>
+#endif
+#include <pci.h>
+#include <mpc83xx.h>
+#include <ns16550.h>
+#include <nand.h>
+
+#include <asm/bitops.h>
+#include <asm/io.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+extern void disable_addr_trans (void);
+extern void enable_addr_trans (void);
+
+int checkboard(void)
+{
+	puts("Board: ve8313\n");
+	return 0;
+}
+
+/* Fixed sdram init -- doesn't use serial presence detect.
+ *
+ * This is useful for faster booting in configs where the RAM is unlikely
+ * to be changed, or for things like NAND booting where space is tight.
+ */
+static long fixed_sdram(void)
+{
+	u32 msize = CONFIG_SYS_DDR_SIZE * 1024 * 1024;
+
+#ifndef CONFIG_SYS_RAMBOOT
+	volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
+	u32 msize_log2 = __ilog2(msize);
+
+	out_be32(&im->sysconf.ddrlaw[0].bar,
+		(CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000));
+	out_be32(&im->sysconf.ddrlaw[0].ar, (LBLAWAR_EN | (msize_log2 - 1)));
+	out_be32(&im->sysconf.ddrcdr, CONFIG_SYS_DDRCDR_VALUE);
+
+	/*
+	 * Erratum DDR3 requires a 50ms delay after clearing DDRCDR[DDR_cfg],
+	 * or the DDR2 controller may fail to initialize correctly.
+	 */
+	__udelay(50000);
+
+	out_be32(&im->ddr.csbnds[0].csbnds, (msize - 1) >> 24);
+	out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CONFIG);
+
+	/* Currently we use only one CS, so disable the other bank. */
+	out_be32(&im->ddr.cs_config[1], 0);
+
+	out_be32(&im->ddr.sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CNTL);
+	out_be32(&im->ddr.timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
+	out_be32(&im->ddr.timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
+	out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
+	out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
+
+	out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_SDRAM_CFG);
+
+	out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_SDRAM_CFG2);
+	out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE);
+	out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE_2);
+
+	out_be32(&im->ddr.sdram_interval, CONFIG_SYS_DDR_INTERVAL);
+	sync();
+
+	/* enable DDR controller */
+	setbits_be32(&im->ddr.sdram_cfg, SDRAM_CFG_MEM_EN);
+
+	/* now check the real size */
+	disable_addr_trans ();
+	msize = get_ram_size (CONFIG_SYS_DDR_BASE, msize);
+	enable_addr_trans ();
+#endif
+
+	return msize;
+}
+
+phys_size_t initdram(int board_type)
+{
+	volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
+	volatile fsl_lbus_t *lbc = &im->lbus;
+	u32 msize;
+
+	if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im)
+		return -1;
+
+	/* DDR SDRAM - Main SODIMM */
+	msize = fixed_sdram();
+
+	/* Local Bus setup lbcr and mrtpr */
+	out_be32(&lbc->lbcr, CONFIG_SYS_LBC_LBCR);
+	out_be32(&lbc->mrtpr, CONFIG_SYS_LBC_MRTPR);
+	sync();
+
+	/* return total bus SDRAM size(bytes)  -- DDR */
+	return msize;
+}
+
+#define VE8313_WDT_EN	0x00020000
+#define VE8313_WDT_TRIG	0x00040000
+
+int board_early_init_f (void)
+{
+	volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
+	volatile gpio83xx_t *gpio = (volatile gpio83xx_t *)im->gpio;
+
+#if defined(CONFIG_HW_WATCHDOG)
+	clrbits_be32(&gpio->dat, (VE8313_WDT_EN | VE8313_WDT_TRIG));
+	/* set WDT pins as output */
+	setbits_be32(&gpio->dir, (VE8313_WDT_EN | VE8313_WDT_TRIG));
+#else
+	/* disable WDT */
+	setbits_be32(&gpio->dat, (VE8313_WDT_EN | VE8313_WDT_TRIG));
+#endif
+	return 0;
+}
+
+#if defined(CONFIG_HW_WATCHDOG)
+void hw_watchdog_reset(void)
+{
+	volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
+	volatile gpio83xx_t *gpio = (volatile gpio83xx_t *)im->gpio;
+
+	setbits_be32(&gpio->dat, (VE8313_WDT_TRIG));
+	clrbits_be32(&gpio->dat, (VE8313_WDT_TRIG));
+}
+#endif
+
+
+#if defined(CONFIG_PCI)
+static struct pci_region pci_regions[] = {
+	{
+		bus_start: CONFIG_SYS_PCI1_MEM_BASE,
+		phys_start: CONFIG_SYS_PCI1_MEM_PHYS,
+		size: CONFIG_SYS_PCI1_MEM_SIZE,
+		flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
+	},
+	{
+		bus_start: CONFIG_SYS_PCI1_MMIO_BASE,
+		phys_start: CONFIG_SYS_PCI1_MMIO_PHYS,
+		size: CONFIG_SYS_PCI1_MMIO_SIZE,
+		flags: PCI_REGION_MEM
+	},
+	{
+		bus_start: CONFIG_SYS_PCI1_IO_BASE,
+		phys_start: CONFIG_SYS_PCI1_IO_PHYS,
+		size: CONFIG_SYS_PCI1_IO_SIZE,
+		flags: PCI_REGION_IO
+	}
+};
+
+void pci_init_board(void)
+{
+	volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
+	volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
+	volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
+	struct pci_region *reg[] = { pci_regions };
+	int warmboot;
+
+	/* Enable all 3 PCI_CLK_OUTPUTs. */
+	setbits_be32(&clk->occr, 0xe0000000);
+
+	/*
+	 * Configure PCI Local Access Windows
+	 */
+	out_be32(&pci_law[0].bar, CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR);
+	out_be32(&pci_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+	out_be32(&pci_law[1].bar, CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR);
+	out_be32(&pci_law[1].ar, LBLAWAR_EN | LBLAWAR_1MB);
+
+	warmboot = gd->bd->bi_bootflags & BOOTFLAG_WARM;
+
+	mpc83xx_pci_init(1, reg, warmboot);
+}
+#endif
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	ft_cpu_setup(blob, bd);
+#ifdef CONFIG_PCI
+	ft_pci_setup(blob, bd);
+#endif
+}
+#endif
diff --git a/boards.cfg b/boards.cfg
index 1a5cfb1..0de35bf 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -135,6 +135,7 @@ TQM8272		powerpc	mpc8260		tqm8272		tqc
 kmeter1		powerpc	mpc83xx		kmeter1		keymile
 MVBLM7		powerpc	mpc83xx		mvblm7		matrix_vision
 TQM834x		powerpc	mpc83xx		tqm834x		tqc
+ve8313		powerpc	mpc83xx		ve8313
 PM854		powerpc	mpc85xx		pm854
 PM856		powerpc	mpc85xx		pm856
 stxgp3		powerpc	mpc85xx		stxgp3		stx
diff --git a/include/configs/ve8313.h b/include/configs/ve8313.h
new file mode 100644
index 0000000..ccd403f
--- /dev/null
+++ b/include/configs/ve8313.h
@@ -0,0 +1,534 @@
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006.
+ *
+ * (C) Copyright 2010
+ * Heiko Schocher, DENX Software Engineering, hs at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+/*
+ * mpc8313epb board configuration file
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300		1
+#define CONFIG_MPC83xx		1
+#define CONFIG_MPC831x		1
+#define CONFIG_MPC8313		1
+#define CONFIG_VE8313		1
+
+#define CONFIG_PCI		1
+
+#define CONFIG_BOARD_EARLY_INIT_F	1
+#undef CONFIG_HW_WATCHDOG
+
+/*
+ * On-board devices
+ *
+ */
+#define CONFIG_83XX_CLKIN	32000000	/* in Hz */
+
+#define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN
+
+#define CONFIG_SYS_IMMR		0xE0000000
+
+#define CONFIG_SYS_MEMTEST_START	0x00001000
+#define CONFIG_SYS_MEMTEST_END		0x07000000
+
+#define CONFIG_SYS_ACR_PIPE_DEP		3	/* Arbiter pipeline depth */
+#define CONFIG_SYS_ACR_RPTCNT		3	/* Arbiter repeat count */
+
+/*
+ * Device configurations
+ */
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_DDR_BASE		0x00000000	/* DDR is system memory*/
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+
+/*
+ * Manually set up DDR parameters, as this board does not
+ * seem to have the SPD connected to I2C.
+ */
+#define CONFIG_SYS_DDR_SIZE		128		/* MB */
+#define CONFIG_SYS_DDR_CONFIG		( CSCONFIG_EN \
+				| CSCONFIG_AP \
+				| 0x00040000 /* TODO */ \
+				| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10 )
+				/* 0x80840102 */
+
+#define CONFIG_SYS_DDR_TIMING_3	0x00000000
+#define CONFIG_SYS_DDR_TIMING_0	( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
+				| ( 0 << TIMING_CFG0_WRT_SHIFT ) \
+				| ( 3 << TIMING_CFG0_RRT_SHIFT ) \
+				| ( 2 << TIMING_CFG0_WWT_SHIFT ) \
+				| ( 7 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \
+				| ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \
+				| ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \
+				| ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) )
+				/* 0x0e720802 */
+#define CONFIG_SYS_DDR_TIMING_1	( ( 2 << TIMING_CFG1_PRETOACT_SHIFT ) \
+				| ( 6 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
+				| ( 2 << TIMING_CFG1_ACTTORW_SHIFT ) \
+				| ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \
+				| ( 6 << TIMING_CFG1_REFREC_SHIFT ) \
+				| ( 2 << TIMING_CFG1_WRREC_SHIFT ) \
+				| ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \
+				| ( 2 << TIMING_CFG1_WRTORD_SHIFT ) )
+				/* 0x26256222 */
+#define CONFIG_SYS_DDR_TIMING_2	( ( 0 << TIMING_CFG2_ADD_LAT_SHIFT ) \
+				| ( 5 << TIMING_CFG2_CPO_SHIFT ) \
+				| ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \
+				| ( 1 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \
+				| ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \
+				| ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \
+				| ( 7 << TIMING_CFG2_FOUR_ACT_SHIFT) )
+				/* 0x029028c7 */
+#define CONFIG_SYS_DDR_INTERVAL	( ( 0x320 << SDRAM_INTERVAL_REFINT_SHIFT ) \
+				| ( 0x2000 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
+				/* 0x03202000 */
+#define CONFIG_SYS_SDRAM_CFG		( SDRAM_CFG_SREN \
+				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
+				| SDRAM_CFG_32_BE )
+				/* 0x43080000 */
+#define CONFIG_SYS_SDRAM_CFG2		0x00401000
+#define CONFIG_SYS_DDR_MODE		( ( 0x4440 << SDRAM_MODE_ESD_SHIFT ) \
+				| ( 0x0232 << SDRAM_MODE_SD_SHIFT ) )
+				/* 0x44400232 */
+#define CONFIG_SYS_DDR_MODE_2		0x8000C000
+
+#define CONFIG_SYS_DDR_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+				/*0x02000000*/
+#define CONFIG_SYS_DDRCDR_VALUE	( DDRCDR_EN \
+				| DDRCDR_PZ_NOMZ \
+				| DDRCDR_NZ_NOMZ \
+				| DDRCDR_M_ODR )
+				/* 0x73000002 */
+
+#if !defined(CONFIG_SYS_NO_FLASH)
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_CFI		/* use the Common Flash Interface */
+#define CONFIG_FLASH_CFI_DRIVER		/* use the CFI driver */
+#define CONFIG_SYS_FLASH_BASE		0xFE000000
+#define CONFIG_SYS_FLASH_SIZE		32	/* size in MB */
+#define CONFIG_SYS_FLASH_EMPTY_INFO		/* display empty sectors */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	/* buffer up multiple bytes */
+#else
+#define CONFIG_SYS_FLASH_BASE		0xFE000000
+#define CONFIG_SYS_FLASH_SIZE		32	/* size in MB */
+#endif
+
+#define CONFIG_SYS_NOR_BR_PRELIM	(CONFIG_SYS_FLASH_BASE | \
+				(2 << BR_PS_SHIFT) |	/* 16 bit */ \
+				BR_V)			/* valid */
+#define CONFIG_SYS_NOR_OR_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
+				| OR_GPCM_CSNT \
+				| OR_GPCM_ACS_DIV4 \
+				| OR_GPCM_SCY_5 \
+				| OR_GPCM_TRLX \
+				| OR_GPCM_EAD)
+				/* 0xfe000c55 */
+
+#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_LBLAWAR0_PRELIM	0x80000018 /* 32 MB window size */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1		/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	256		/* sectors per dev */
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE	/* start of monitor */
+
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_SYS_INIT_RAM_LOCK	1
+#define CONFIG_SYS_INIT_RAM_ADDR	0xFD000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END		0x1000	/* End of used area in RAM*/
+
+#define CONFIG_SYS_GBL_DATA_SIZE	0x100	/* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - \
+					 CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
+#define CONFIG_SYS_MONITOR_LEN		(384 * 1024)
+#define CONFIG_SYS_MALLOC_LEN		(512 * 1024)
+
+/*
+ * Local Bus LCRR and LBCR regs
+ */
+#define CONFIG_SYS_LCRR_EADC	LCRR_EADC_3
+#define CONFIG_SYS_LCRR_CLKDIV	LCRR_CLKDIV_2
+
+#define CONFIG_SYS_LBC_LBCR	(0x00040000)
+
+#define CONFIG_SYS_LBC_MRTPR	0x20000000
+
+/*
+ * NAND settings
+ */
+#define CONFIG_SYS_NAND_BASE		0x61000000
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND 1
+#define CONFIG_NAND_FSL_ELBC 1
+#define CONFIG_SYS_NAND_BLOCK_SIZE 16384
+
+#define CONFIG_SYS_NAND_BR_PRELIM	( CONFIG_SYS_NAND_BASE \
+				| BR_PS_8		\
+				| BR_DECC_CHK_GEN	\
+				| BR_MS_FCM		\
+				| BR_V )	/* valid */
+				/* 0x61000c21 */
+#define CONFIG_SYS_NAND_OR_PRELIM	(0xffff8000 \
+				| OR_FCM_BCTLD \
+				| OR_FCM_CHT \
+				| OR_FCM_SCY_2 \
+				| OR_FCM_RST \
+				| OR_FCM_TRLX)
+				/* 0xffff90ac */
+
+#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM
+#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM
+#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM
+#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM
+
+#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_NAND_BASE
+#define CONFIG_SYS_LBLAWAR1_PRELIM	0x8000000E	/* 32KB  */
+
+#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
+#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM
+
+/* CS2 NvRAM */
+#define CONFIG_SYS_BR2_PRELIM	(0x60000000	\
+				| BR_PS_8	\
+				| BR_V)
+				/* 0x60000801 */
+#define CONFIG_SYS_OR2_PRELIM	(0xfffe0000	\
+				| OR_GPCM_CSNT	\
+				| OR_GPCM_XACS	\
+				| OR_GPCM_SCY_3 \
+				| OR_GPCM_TRLX \
+				| OR_GPCM_EHTR \
+				| OR_GPCM_EAD)
+				/* 0xfffe0937 */
+/* local bus read write buffer mapping SRAM@0x64000000 */
+#define CONFIG_SYS_BR3_PRELIM	(0x62000000	\
+				| BR_PS_16	\
+				| BR_V)
+				/* 0x62001001 */
+
+#define CONFIG_SYS_OR3_PRELIM	(0xfe000000	\
+				| OR_GPCM_CSNT	\
+				| OR_GPCM_XACS	\
+				| OR_GPCM_SCY_15 \
+				| OR_GPCM_TRLX \
+				| OR_GPCM_EHTR \
+				| OR_GPCM_EAD)
+				/* 0xfe0009f7 */
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT	1
+#define CONFIG_OF_BOARD_SETUP	1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX	1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+#if defined(CONFIG_PCI)
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI1_MMIO_BASE	0x90000000
+#define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
+#define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI1_IO_BASE	0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS	0xE2000000
+#define CONFIG_SYS_PCI1_IO_SIZE	0x00100000	/* 1M */
+
+#define CONFIG_PCI_PNP		/* do pci plug-and-play */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057	/* Motorola */
+#endif
+
+/*
+ * TSEC
+ */
+#define CONFIG_TSEC_ENET		/* TSEC ethernet support */
+
+#define CONFIG_NET_MULTI
+
+#define CONFIG_TSEC1
+
+#ifdef CONFIG_TSEC1
+#define CONFIG_HAS_ETH0
+#define CONFIG_TSEC1_NAME	"TSEC0"
+#define CONFIG_SYS_TSEC1_OFFSET	0x24000
+#define TSEC1_PHY_ADDR		0x01
+#define TSEC1_FLAGS		0
+#define TSEC1_PHYIDX		0
+#endif
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME			"TSEC0"
+
+/*
+ * Environment
+ */
+#if !defined(CONFIG_SYS_RAMBOOT)
+	#define CONFIG_ENV_IS_IN_FLASH	1
+	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
+						CONFIG_SYS_MONITOR_LEN)
+	#define CONFIG_ENV_SECT_SIZE	0x20000	/* 64K(one sector) for env */
+	#define CONFIG_ENV_SIZE		0x2000
+
+/* Address and size of Redundant Environment Sector */
+#else
+	#define CONFIG_SYS_NO_FLASH	1	/* Flash is not usable now */
+	#define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in mem only */
+	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
+	#define CONFIG_ENV_SIZE		0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_PCI
+
+#if defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_NAND_U_BOOT)
+    #undef CONFIG_CMD_SAVEENV
+    #undef CONFIG_CMD_LOADS
+#endif
+
+#define CONFIG_CMDLINE_EDITING 1
+#define CONFIG_AUTO_COMPLETE	/* add autocompletion support   */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
+
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS	16		/* max number of cmd args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE /* Boot arg Buffer size */
+#define CONFIG_SYS_HZ		1000		/* 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
+
+/* 0x64050000 */
+#define CONFIG_SYS_HRCW_LOW (\
+	0x20000000 /* reserved, must be set */ |\
+	HRCWL_DDRCM |\
+	HRCWL_CSB_TO_CLKIN_4X1 | \
+	HRCWL_CORE_TO_CSB_2_5X1)
+
+/* 0xa0600004 */
+#define CONFIG_SYS_HRCW_HIGH (HRCWH_PCI_HOST | \
+	HRCWH_PCI_ARBITER_ENABLE | \
+	HRCWH_CORE_ENABLE | \
+	HRCWH_FROM_0X00000100 | \
+	HRCWH_BOOTSEQ_DISABLE |\
+	HRCWH_SW_WATCHDOG_DISABLE |\
+	HRCWH_ROM_LOC_LOCAL_16BIT | \
+	HRCWH_TSEC1M_IN_MII | \
+	HRCWH_BIG_ENDIAN | \
+	HRCWH_LALE_EARLY)
+
+/* System IO Config */
+#define CONFIG_SYS_SICRH	(0x01000000 | \
+				SICRH_ETSEC2_B | \
+				SICRH_ETSEC2_C | \
+				SICRH_ETSEC2_D | \
+				SICRH_ETSEC2_E | \
+				SICRH_ETSEC2_F | \
+				SICRH_ETSEC2_G | \
+				SICRH_TSOBI1 | \
+				SICRH_TSOBI2)
+				/* 0x010fff03 */
+#define CONFIG_SYS_SICRL	(SICRL_LBC | \
+				SICRL_SPI_A | \
+				SICRL_SPI_B | \
+				SICRL_SPI_C | \
+				SICRL_SPI_D | \
+				SICRL_ETSEC2_A)
+				/* 0x33fc0003) */
+
+#define CONFIG_SYS_HID0_INIT	0x000000000
+#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
+				 HID0_ENABLE_INSTRUCTION_CACHE)
+
+#define CONFIG_SYS_HID2 HID2_HBE
+
+#define CONFIG_HIGH_BATS	1	/* High BATs supported */
+
+/* DDR @ 0x00000000 */
+#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_10)
+#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | \
+				 BATU_VS | BATU_VP)
+
+#if defined(CONFIG_PCI)
+/* PCI @ 0x80000000 */
+#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_10)
+#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | \
+				BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_10 | \
+				BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | \
+				BATU_VS | BATU_VP)
+#else
+#define CONFIG_SYS_IBAT1L	(0)
+#define CONFIG_SYS_IBAT1U	(0)
+#define CONFIG_SYS_IBAT2L	(0)
+#define CONFIG_SYS_IBAT2U	(0)
+#endif
+
+/* PCI2 not supported on 8313 */
+#define CONFIG_SYS_IBAT3L	(0)
+#define CONFIG_SYS_IBAT3U	(0)
+#define CONFIG_SYS_IBAT4L	(0)
+#define CONFIG_SYS_IBAT4U	(0)
+
+/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
+#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_IMMR | BATL_PP_10 | \
+				BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_IMMR | BATU_BL_256M | BATU_VS | \
+				BATU_VP)
+
+/* stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
+#define CONFIG_SYS_IBAT6L	(0xF0000000 | BATL_PP_10 | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT6U	(0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/*  FPGA, SRAM, NAND @ 0x60000000 */
+#define CONFIG_SYS_IBAT7L	(0x60000000 | BATL_PP_10 | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT7U	(0x60000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
+#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
+#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
+#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
+#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
+#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
+#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
+#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
+#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
+#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01	/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02	/* Software reboot */
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_NETDEV		eth0
+
+#define CONFIG_HOSTNAME		ve8313
+#define CONFIG_UBOOTPATH	ve8313/u-boot.bin
+
+#define CONFIG_LOADADDR		800000
+#define CONFIG_BOOTDELAY	6	/* -1 disables auto-boot */
+#define CONFIG_BAUDRATE		115200
+
+#define XMK_STR(x)	#x
+#define MK_STR(x)	XMK_STR(x)
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"netdev=" MK_STR(CONFIG_NETDEV) "\0"				\
+	"ethprime=TSEC0\0"						\
+	"u-boot=" MK_STR(CONFIG_UBOOTPATH) "\0"				\
+	"u-boot_addr_r=100000\0"					\
+	"load=tftp ${u-boot_addr_r} ${u-boot}\0"			\
+	"update=protect off " MK_STR(CONFIG_SYS_FLASH_BASE) " +${filesize};" \
+	"erase " MK_STR(CONFIG_SYS_FLASH_BASE) " +${filesize};" \
+	"cp.b ${u-boot_addr_r} " MK_STR(CONFIG_SYS_FLASH_BASE) \
+	" ${filesize};" \
+	"protect on " MK_STR(CONFIG_SYS_FLASH_BASE) " +${filesize}\0" \
+
+#undef MK_STR
+#undef XMK_STR
+
+#endif	/* __CONFIG_H */
-- 
1.6.2.5

-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

[U-Boot] 83xx: add support for ve8313 board

[Kim Phillips]

On Mon, 5 Jul 2010 12:23:10 +0200
Heiko Schocher <hs@denx.de> wrote:

> ---
>  board/ve8313/Makefile    |   50 +++++
>  board/ve8313/config.mk   |   10 +
>  board/ve8313/ve8313.c    |  212 ++++++++++++++++++
>  boards.cfg               |    1 +
>  include/configs/ve8313.h |  534 ++++++++++++++++++++++++++++++++++++++++++++++
>  5 files changed, 807 insertions(+), 0 deletions(-)

missing MAKEALL, MAINTAINERS entries, and, if there's anything unique
about this board, a doc/README.ve8313.

> diff --git a/board/ve8313/config.mk b/board/ve8313/config.mk

> +ifndef TEXT_BASE
> +#TEXT_BASE = 0x100000
> +TEXT_BASE = 0xfe000000
> +endif
> +
> +#PLATFORM_CPPFLAGS += -DDEBUG

please clean this up - remove commented out code.

> diff --git a/board/ve8313/ve8313.c b/board/ve8313/ve8313.c
> new file mode 100644
> index 0000000..b13d1f3
> --- /dev/null
> +++ b/board/ve8313/ve8313.c
> @@ -0,0 +1,212 @@
> +/*
> + * (C) Copyright 2010
> + * Heiko Schocher, DENX Software Engineering, hs at denx.de.

this file contains code that looks like it was copied from files with
Freescale copyrights; why are you deleting Freescale's copyrights?

> +#if defined(CONFIG_OF_LIBFDT)
> +#include <libfdt.h>
> +#endif

I realise this was copied in, but we don't need the ifdef anymore.

> +/* Fixed sdram init -- doesn't use serial presence detect.
> + *
> + * This is useful for faster booting in configs where the RAM is unlikely
> + * to be changed, or for things like NAND booting where space is tight.
> + */

Is the memory soldered on to the board?  If not, does the serial
presence detect code not work for you?

> +#if defined(CONFIG_HW_WATCHDOG)
> +	clrbits_be32(&gpio->dat, (VE8313_WDT_EN | VE8313_WDT_TRIG));
> +	/* set WDT pins as output */
> +	setbits_be32(&gpio->dir, (VE8313_WDT_EN | VE8313_WDT_TRIG));
> +#else
> +	/* disable WDT */
> +	setbits_be32(&gpio->dat, (VE8313_WDT_EN | VE8313_WDT_TRIG));

inner parens not necessary, also the last WDT_EN bit setting doesn't
match the comment above it (ENable vs. disable) - perhaps nothing
need be done if HW_WATCHDOG is not set?

> +	setbits_be32(&gpio->dat, (VE8313_WDT_TRIG));
> +	clrbits_be32(&gpio->dat, (VE8313_WDT_TRIG));

inner parens not necessary.

> +#undef CONFIG_HW_WATCHDOG

no #undefs please.

> +#define CONFIG_SYS_LBC_LBCR	(0x00040000)

parens not necessary.

> +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057	/* Motorola */

It's Freescale: 0x1957.

Thanks,

Kim

[U-Boot] 83xx: add support for ve8313 board

[Heiko Schocher]

Hello Kim,

Kim Phillips wrote:
> On Mon, 5 Jul 2010 12:23:10 +0200
> Heiko Schocher <hs@denx.de> wrote:
> 
>> ---
>>  board/ve8313/Makefile    |   50 +++++
>>  board/ve8313/config.mk   |   10 +
>>  board/ve8313/ve8313.c    |  212 ++++++++++++++++++
>>  boards.cfg               |    1 +
>>  include/configs/ve8313.h |  534 ++++++++++++++++++++++++++++++++++++++++++++++
>>  5 files changed, 807 insertions(+), 0 deletions(-)
> 
> missing MAKEALL, MAINTAINERS entries, and, if there's anything unique
> about this board, a doc/README.ve8313.

There is nothing unique on this board, so don;t think a
doc/README.ve8313 is useful.

>> diff --git a/board/ve8313/config.mk b/board/ve8313/config.mk
> 
>> +ifndef TEXT_BASE
>> +#TEXT_BASE = 0x100000
>> +TEXT_BASE = 0xfe000000
>> +endif
>> +
>> +#PLATFORM_CPPFLAGS += -DDEBUG
> 
> please clean this up - remove commented out code.

fixed.

>> diff --git a/board/ve8313/ve8313.c b/board/ve8313/ve8313.c
>> new file mode 100644
>> index 0000000..b13d1f3
>> --- /dev/null
>> +++ b/board/ve8313/ve8313.c
>> @@ -0,0 +1,212 @@
>> +/*
>> + * (C) Copyright 2010
>> + * Heiko Schocher, DENX Software Engineering, hs at denx.de.
> 
> this file contains code that looks like it was copied from files with
> Freescale copyrights; why are you deleting Freescale's copyrights?

Hups, Sorry for that.

>> +#if defined(CONFIG_OF_LIBFDT)
>> +#include <libfdt.h>
>> +#endif
> 
> I realise this was copied in, but we don't need the ifdef anymore.

done.

>> +/* Fixed sdram init -- doesn't use serial presence detect.
>> + *
>> + * This is useful for faster booting in configs where the RAM is unlikely
>> + * to be changed, or for things like NAND booting where space is tight.
>> + */
> 
> Is the memory soldered on to the board?  If not, does the serial
> presence detect code not work for you?

It is soldered.

>> +#if defined(CONFIG_HW_WATCHDOG)
>> +	clrbits_be32(&gpio->dat, (VE8313_WDT_EN | VE8313_WDT_TRIG));
>> +	/* set WDT pins as output */
>> +	setbits_be32(&gpio->dir, (VE8313_WDT_EN | VE8313_WDT_TRIG));
>> +#else
>> +	/* disable WDT */
>> +	setbits_be32(&gpio->dat, (VE8313_WDT_EN | VE8313_WDT_TRIG));
> 
> inner parens not necessary, also the last WDT_EN bit setting doesn't
> match the comment above it (ENable vs. disable) - perhaps nothing
> need be done if HW_WATCHDOG is not set?

I must explicitely disable the WDT.

>> +	setbits_be32(&gpio->dat, (VE8313_WDT_TRIG));
>> +	clrbits_be32(&gpio->dat, (VE8313_WDT_TRIG));
> 
> inner parens not necessary.

done.

> 
>> +#undef CONFIG_HW_WATCHDOG
> 
> no #undefs please.

removed.

>> +#define CONFIG_SYS_LBC_LBCR	(0x00040000)
> 
> parens not necessary.

fixed.

>> +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057	/* Motorola */
> 
> It's Freescale: 0x1957.

fixed.

Thanks for your review.

bye
Heiko
-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

[U-Boot] [PATCH v2] 83xx: add support for ve8313 board

[Heiko Schocher]

This patch add support for the ve8313 board based on
Freescale MPC8313 CPU.

- serial console on UART 1
- 128 MB DDR RAM
- 32 MB NOR Flash
- 16 MB NAND Flash
- Ethernet MII Mode over on TSEC0
- micrel ksz804 phy
- Hardware WDT MAX824

Signed-off-by: Heiko Schocher <hs@denx.de>
---
changes since v1
- environment size = sector size
- use red. environment
- add comments from Kim Phillips
  - add MAKEALL, MAINTAINERS entry
  - Codingstyle issues fixed
  - inserted original Copyrights
  - PCI subsys vendor ID changed from 0x1057 (Motorola)
    to 0x1957 (Freescale)

 MAINTAINERS              |    1 +
 MAKEALL                  |    1 +
 board/ve8313/Makefile    |   50 +++++
 board/ve8313/config.mk   |    7 +
 board/ve8313/ve8313.c    |  215 +++++++++++++++++++
 boards.cfg               |    1 +
 include/configs/ve8313.h |  534 ++++++++++++++++++++++++++++++++++++++++++++++
 7 files changed, 809 insertions(+), 0 deletions(-)
 create mode 100644 board/ve8313/Makefile
 create mode 100644 board/ve8313/config.mk
 create mode 100644 board/ve8313/ve8313.c
 create mode 100644 include/configs/ve8313.h

diff --git a/MAINTAINERS b/MAINTAINERS
index d7aec98..88a3d79 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -427,6 +427,7 @@ Heiko Schocher <hs@denx.de>
 	sc3		PPC405GP
 	suen3		ARM926EJS (Kirkwood SoC)
 	uc101		MPC5200
+	ve8313		MPC8313

 Peter De Schrijver <p2@mind.be>

diff --git a/MAKEALL b/MAKEALL
index 27f8bd1..eedae60 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -379,6 +379,7 @@ LIST_83xx="		\
 	sbc8349		\
 	SIMPC8313_LP	\
 	TQM834x		\
+	ve8313		\
 	vme8349		\
 "

diff --git a/board/ve8313/Makefile b/board/ve8313/Makefile
new file mode 100644
index 0000000..c95f90e
--- /dev/null
+++ b/board/ve8313/Makefile
@@ -0,0 +1,50 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	:= $(BOARD).o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/ve8313/config.mk b/board/ve8313/config.mk
new file mode 100644
index 0000000..02dd33e
--- /dev/null
+++ b/board/ve8313/config.mk
@@ -0,0 +1,7 @@
+ifndef NAND_SPL
+sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp
+endif
+
+ifndef TEXT_BASE
+TEXT_BASE = 0xfe000000
+endif
diff --git a/board/ve8313/ve8313.c b/board/ve8313/ve8313.c
new file mode 100644
index 0000000..7dfacfb
--- /dev/null
+++ b/board/ve8313/ve8313.c
@@ -0,0 +1,215 @@
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006-2007
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * (C) Copyright 2010
+ * Heiko Schocher, DENX Software Engineering, hs at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <libfdt.h>
+#include <pci.h>
+#include <mpc83xx.h>
+#include <ns16550.h>
+#include <nand.h>
+
+#include <asm/bitops.h>
+#include <asm/io.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+extern void disable_addr_trans (void);
+extern void enable_addr_trans (void);
+
+int checkboard(void)
+{
+	puts("Board: ve8313\n");
+	return 0;
+}
+
+/* Fixed sdram init -- doesn't use serial presence detect.
+ *
+ * This is useful for faster booting in configs where the RAM is unlikely
+ * to be changed, or for things like NAND booting where space is tight.
+ */
+static long fixed_sdram(void)
+{
+	u32 msize = CONFIG_SYS_DDR_SIZE * 1024 * 1024;
+
+#ifndef CONFIG_SYS_RAMBOOT
+	volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
+	u32 msize_log2 = __ilog2(msize);
+
+	out_be32(&im->sysconf.ddrlaw[0].bar,
+		(CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000));
+	out_be32(&im->sysconf.ddrlaw[0].ar, (LBLAWAR_EN | (msize_log2 - 1)));
+	out_be32(&im->sysconf.ddrcdr, CONFIG_SYS_DDRCDR_VALUE);
+
+	/*
+	 * Erratum DDR3 requires a 50ms delay after clearing DDRCDR[DDR_cfg],
+	 * or the DDR2 controller may fail to initialize correctly.
+	 */
+	__udelay(50000);
+
+	out_be32(&im->ddr.csbnds[0].csbnds, (msize - 1) >> 24);
+	out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CONFIG);
+
+	/* Currently we use only one CS, so disable the other bank. */
+	out_be32(&im->ddr.cs_config[1], 0);
+
+	out_be32(&im->ddr.sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CNTL);
+	out_be32(&im->ddr.timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
+	out_be32(&im->ddr.timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
+	out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
+	out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
+
+	out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_SDRAM_CFG);
+
+	out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_SDRAM_CFG2);
+	out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE);
+	out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE_2);
+
+	out_be32(&im->ddr.sdram_interval, CONFIG_SYS_DDR_INTERVAL);
+	sync();
+
+	/* enable DDR controller */
+	setbits_be32(&im->ddr.sdram_cfg, SDRAM_CFG_MEM_EN);
+
+	/* now check the real size */
+	disable_addr_trans ();
+	msize = get_ram_size (CONFIG_SYS_DDR_BASE, msize);
+	enable_addr_trans ();
+#endif
+
+	return msize;
+}
+
+phys_size_t initdram(int board_type)
+{
+	volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
+	volatile fsl_lbus_t *lbc = &im->lbus;
+	u32 msize;
+
+	if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im)
+		return -1;
+
+	/* DDR SDRAM - Main SODIMM */
+	msize = fixed_sdram();
+
+	/* Local Bus setup lbcr and mrtpr */
+	out_be32(&lbc->lbcr, CONFIG_SYS_LBC_LBCR);
+	out_be32(&lbc->mrtpr, CONFIG_SYS_LBC_MRTPR);
+	sync();
+
+	/* return total bus SDRAM size(bytes)  -- DDR */
+	return msize;
+}
+
+#define VE8313_WDT_EN	0x00020000
+#define VE8313_WDT_TRIG	0x00040000
+
+int board_early_init_f (void)
+{
+	volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
+	volatile gpio83xx_t *gpio = (volatile gpio83xx_t *)im->gpio;
+
+	/* set WDT pins as output */
+	setbits_be32(&gpio->dir, VE8313_WDT_EN | VE8313_WDT_TRIG);
+#if defined(CONFIG_HW_WATCHDOG)
+	/* enable WDT */
+	clrbits_be32(&gpio->dat, VE8313_WDT_EN | VE8313_WDT_TRIG);
+#else
+	/* disable WDT */
+	setbits_be32(&gpio->dat, VE8313_WDT_EN | VE8313_WDT_TRIG);
+#endif
+	return 0;
+}
+
+#if defined(CONFIG_HW_WATCHDOG)
+void hw_watchdog_reset(void)
+{
+	volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
+	volatile gpio83xx_t *gpio = (volatile gpio83xx_t *)im->gpio;
+
+	setbits_be32(&gpio->dat, VE8313_WDT_TRIG);
+	clrbits_be32(&gpio->dat, VE8313_WDT_TRIG);
+}
+#endif
+
+
+#if defined(CONFIG_PCI)
+static struct pci_region pci_regions[] = {
+	{
+		bus_start: CONFIG_SYS_PCI1_MEM_BASE,
+		phys_start: CONFIG_SYS_PCI1_MEM_PHYS,
+		size: CONFIG_SYS_PCI1_MEM_SIZE,
+		flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
+	},
+	{
+		bus_start: CONFIG_SYS_PCI1_MMIO_BASE,
+		phys_start: CONFIG_SYS_PCI1_MMIO_PHYS,
+		size: CONFIG_SYS_PCI1_MMIO_SIZE,
+		flags: PCI_REGION_MEM
+	},
+	{
+		bus_start: CONFIG_SYS_PCI1_IO_BASE,
+		phys_start: CONFIG_SYS_PCI1_IO_PHYS,
+		size: CONFIG_SYS_PCI1_IO_SIZE,
+		flags: PCI_REGION_IO
+	}
+};
+
+void pci_init_board(void)
+{
+	volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
+	volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
+	volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
+	struct pci_region *reg[] = { pci_regions };
+	int warmboot;
+
+	/* Enable all 3 PCI_CLK_OUTPUTs. */
+	setbits_be32(&clk->occr, 0xe0000000);
+
+	/*
+	 * Configure PCI Local Access Windows
+	 */
+	out_be32(&pci_law[0].bar, CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR);
+	out_be32(&pci_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+	out_be32(&pci_law[1].bar, CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR);
+	out_be32(&pci_law[1].ar, LBLAWAR_EN | LBLAWAR_1MB);
+
+	warmboot = gd->bd->bi_bootflags & BOOTFLAG_WARM;
+
+	mpc83xx_pci_init(1, reg, warmboot);
+}
+#endif
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	ft_cpu_setup(blob, bd);
+#ifdef CONFIG_PCI
+	ft_pci_setup(blob, bd);
+#endif
+}
+#endif
diff --git a/boards.cfg b/boards.cfg
index 1a5cfb1..0de35bf 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -135,6 +135,7 @@ TQM8272		powerpc	mpc8260		tqm8272		tqc
 kmeter1		powerpc	mpc83xx		kmeter1		keymile
 MVBLM7		powerpc	mpc83xx		mvblm7		matrix_vision
 TQM834x		powerpc	mpc83xx		tqm834x		tqc
+ve8313		powerpc	mpc83xx		ve8313
 PM854		powerpc	mpc85xx		pm854
 PM856		powerpc	mpc85xx		pm856
 stxgp3		powerpc	mpc85xx		stxgp3		stx
diff --git a/include/configs/ve8313.h b/include/configs/ve8313.h
new file mode 100644
index 0000000..96f79a8
--- /dev/null
+++ b/include/configs/ve8313.h
@@ -0,0 +1,534 @@
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006.
+ *
+ * (C) Copyright 2010
+ * Heiko Schocher, DENX Software Engineering, hs at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+/*
+ * ve8313 board configuration file
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300		1
+#define CONFIG_MPC83xx		1
+#define CONFIG_MPC831x		1
+#define CONFIG_MPC8313		1
+#define CONFIG_VE8313		1
+
+#define CONFIG_PCI		1
+
+#define CONFIG_BOARD_EARLY_INIT_F	1
+
+/*
+ * On-board devices
+ *
+ */
+#define CONFIG_83XX_CLKIN	32000000	/* in Hz */
+
+#define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN
+
+#define CONFIG_SYS_IMMR		0xE0000000
+
+#define CONFIG_SYS_MEMTEST_START	0x00001000
+#define CONFIG_SYS_MEMTEST_END		0x07000000
+
+#define CONFIG_SYS_ACR_PIPE_DEP		3	/* Arbiter pipeline depth */
+#define CONFIG_SYS_ACR_RPTCNT		3	/* Arbiter repeat count */
+
+/*
+ * Device configurations
+ */
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_DDR_BASE		0x00000000	/* DDR is system memory*/
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+
+/*
+ * Manually set up DDR parameters, as this board does not
+ * seem to have the SPD connected to I2C.
+ */
+#define CONFIG_SYS_DDR_SIZE		128		/* MB */
+#define CONFIG_SYS_DDR_CONFIG		( CSCONFIG_EN \
+				| CSCONFIG_AP \
+				| 0x00040000 /* TODO */ \
+				| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10 )
+				/* 0x80840102 */
+
+#define CONFIG_SYS_DDR_TIMING_3	0x00000000
+#define CONFIG_SYS_DDR_TIMING_0	( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
+				| ( 0 << TIMING_CFG0_WRT_SHIFT ) \
+				| ( 3 << TIMING_CFG0_RRT_SHIFT ) \
+				| ( 2 << TIMING_CFG0_WWT_SHIFT ) \
+				| ( 7 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \
+				| ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \
+				| ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \
+				| ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) )
+				/* 0x0e720802 */
+#define CONFIG_SYS_DDR_TIMING_1	( ( 2 << TIMING_CFG1_PRETOACT_SHIFT ) \
+				| ( 6 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
+				| ( 2 << TIMING_CFG1_ACTTORW_SHIFT ) \
+				| ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \
+				| ( 6 << TIMING_CFG1_REFREC_SHIFT ) \
+				| ( 2 << TIMING_CFG1_WRREC_SHIFT ) \
+				| ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \
+				| ( 2 << TIMING_CFG1_WRTORD_SHIFT ) )
+				/* 0x26256222 */
+#define CONFIG_SYS_DDR_TIMING_2	( ( 0 << TIMING_CFG2_ADD_LAT_SHIFT ) \
+				| ( 5 << TIMING_CFG2_CPO_SHIFT ) \
+				| ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \
+				| ( 1 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \
+				| ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \
+				| ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \
+				| ( 7 << TIMING_CFG2_FOUR_ACT_SHIFT) )
+				/* 0x029028c7 */
+#define CONFIG_SYS_DDR_INTERVAL	( ( 0x320 << SDRAM_INTERVAL_REFINT_SHIFT ) \
+				| ( 0x2000 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
+				/* 0x03202000 */
+#define CONFIG_SYS_SDRAM_CFG		( SDRAM_CFG_SREN \
+				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
+				| SDRAM_CFG_32_BE )
+				/* 0x43080000 */
+#define CONFIG_SYS_SDRAM_CFG2		0x00401000
+#define CONFIG_SYS_DDR_MODE		( ( 0x4440 << SDRAM_MODE_ESD_SHIFT ) \
+				| ( 0x0232 << SDRAM_MODE_SD_SHIFT ) )
+				/* 0x44400232 */
+#define CONFIG_SYS_DDR_MODE_2		0x8000C000
+
+#define CONFIG_SYS_DDR_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+				/*0x02000000*/
+#define CONFIG_SYS_DDRCDR_VALUE	( DDRCDR_EN \
+				| DDRCDR_PZ_NOMZ \
+				| DDRCDR_NZ_NOMZ \
+				| DDRCDR_M_ODR )
+				/* 0x73000002 */
+
+#if !defined(CONFIG_SYS_NO_FLASH)
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_CFI		/* use the Common Flash Interface */
+#define CONFIG_FLASH_CFI_DRIVER		/* use the CFI driver */
+#define CONFIG_SYS_FLASH_BASE		0xFE000000
+#define CONFIG_SYS_FLASH_SIZE		32	/* size in MB */
+#define CONFIG_SYS_FLASH_EMPTY_INFO		/* display empty sectors */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	/* buffer up multiple bytes */
+#else
+#define CONFIG_SYS_FLASH_BASE		0xFE000000
+#define CONFIG_SYS_FLASH_SIZE		32	/* size in MB */
+#endif
+
+#define CONFIG_SYS_NOR_BR_PRELIM	(CONFIG_SYS_FLASH_BASE | \
+				(2 << BR_PS_SHIFT) |	/* 16 bit */ \
+				BR_V)			/* valid */
+#define CONFIG_SYS_NOR_OR_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
+				| OR_GPCM_CSNT \
+				| OR_GPCM_ACS_DIV4 \
+				| OR_GPCM_SCY_5 \
+				| OR_GPCM_TRLX \
+				| OR_GPCM_EAD)
+				/* 0xfe000c55 */
+
+#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_LBLAWAR0_PRELIM	0x80000018 /* 32 MB window size */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1		/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	256		/* sectors per dev */
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE	/* start of monitor */
+
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_SYS_INIT_RAM_LOCK	1
+#define CONFIG_SYS_INIT_RAM_ADDR	0xFD000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END		0x1000	/* End of used area in RAM*/
+
+#define CONFIG_SYS_GBL_DATA_SIZE	0x100	/* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - \
+					 CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
+#define CONFIG_SYS_MONITOR_LEN		(384 * 1024)
+#define CONFIG_SYS_MALLOC_LEN		(512 * 1024)
+
+/*
+ * Local Bus LCRR and LBCR regs
+ */
+#define CONFIG_SYS_LCRR_EADC	LCRR_EADC_3
+#define CONFIG_SYS_LCRR_CLKDIV	LCRR_CLKDIV_2
+
+#define CONFIG_SYS_LBC_LBCR	0x00040000
+
+#define CONFIG_SYS_LBC_MRTPR	0x20000000
+
+/*
+ * NAND settings
+ */
+#define CONFIG_SYS_NAND_BASE		0x61000000
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND 1
+#define CONFIG_NAND_FSL_ELBC 1
+#define CONFIG_SYS_NAND_BLOCK_SIZE 16384
+
+#define CONFIG_SYS_NAND_BR_PRELIM	( CONFIG_SYS_NAND_BASE \
+				| BR_PS_8		\
+				| BR_DECC_CHK_GEN	\
+				| BR_MS_FCM		\
+				| BR_V )	/* valid */
+				/* 0x61000c21 */
+#define CONFIG_SYS_NAND_OR_PRELIM	(0xffff8000 \
+				| OR_FCM_BCTLD \
+				| OR_FCM_CHT \
+				| OR_FCM_SCY_2 \
+				| OR_FCM_RST \
+				| OR_FCM_TRLX)
+				/* 0xffff90ac */
+
+#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM
+#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM
+#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM
+#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM
+
+#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_NAND_BASE
+#define CONFIG_SYS_LBLAWAR1_PRELIM	0x8000000E	/* 32KB  */
+
+#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
+#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM
+
+/* CS2 NvRAM */
+#define CONFIG_SYS_BR2_PRELIM	(0x60000000	\
+				| BR_PS_8	\
+				| BR_V)
+				/* 0x60000801 */
+#define CONFIG_SYS_OR2_PRELIM	(0xfffe0000	\
+				| OR_GPCM_CSNT	\
+				| OR_GPCM_XACS	\
+				| OR_GPCM_SCY_3 \
+				| OR_GPCM_TRLX \
+				| OR_GPCM_EHTR \
+				| OR_GPCM_EAD)
+				/* 0xfffe0937 */
+/* local bus read write buffer mapping SRAM@0x64000000 */
+#define CONFIG_SYS_BR3_PRELIM	(0x62000000	\
+				| BR_PS_16	\
+				| BR_V)
+				/* 0x62001001 */
+
+#define CONFIG_SYS_OR3_PRELIM	(0xfe000000	\
+				| OR_GPCM_CSNT	\
+				| OR_GPCM_XACS	\
+				| OR_GPCM_SCY_15 \
+				| OR_GPCM_TRLX \
+				| OR_GPCM_EHTR \
+				| OR_GPCM_EAD)
+				/* 0xfe0009f7 */
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT	1
+#define CONFIG_OF_BOARD_SETUP	1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX	1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+#if defined(CONFIG_PCI)
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI1_MMIO_BASE	0x90000000
+#define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
+#define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI1_IO_BASE	0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS	0xE2000000
+#define CONFIG_SYS_PCI1_IO_SIZE	0x00100000	/* 1M */
+
+#define CONFIG_PCI_PNP		/* do pci plug-and-play */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957	/* Freescale */
+#endif
+
+/*
+ * TSEC
+ */
+#define CONFIG_TSEC_ENET		/* TSEC ethernet support */
+
+#define CONFIG_NET_MULTI
+
+#define CONFIG_TSEC1
+
+#ifdef CONFIG_TSEC1
+#define CONFIG_HAS_ETH0
+#define CONFIG_TSEC1_NAME	"TSEC0"
+#define CONFIG_SYS_TSEC1_OFFSET	0x24000
+#define TSEC1_PHY_ADDR		0x01
+#define TSEC1_FLAGS		0
+#define TSEC1_PHYIDX		0
+#endif
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME			"TSEC0"
+
+/*
+ * Environment
+ */
+#if !defined(CONFIG_SYS_RAMBOOT)
+	#define CONFIG_ENV_IS_IN_FLASH	1
+	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
+						CONFIG_SYS_MONITOR_LEN)
+	#define CONFIG_ENV_SECT_SIZE	0x20000	/* 64K(one sector) for env */
+	/* Address and size of Redundant Environment Sector */
+	#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
+						CONFIG_ENV_SECT_SIZE)
+	#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
+#else
+	#define CONFIG_SYS_NO_FLASH	1	/* Flash is not usable now */
+	#define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in mem only */
+	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
+	#define CONFIG_ENV_SIZE		0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_PCI
+
+#if defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_NAND_U_BOOT)
+    #undef CONFIG_CMD_SAVEENV
+    #undef CONFIG_CMD_LOADS
+#endif
+
+#define CONFIG_CMDLINE_EDITING 1
+#define CONFIG_AUTO_COMPLETE	/* add autocompletion support   */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
+
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS	16		/* max number of cmd args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE /* Boot arg Buffer size */
+#define CONFIG_SYS_HZ		1000		/* 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
+
+/* 0x64050000 */
+#define CONFIG_SYS_HRCW_LOW (\
+	0x20000000 /* reserved, must be set */ |\
+	HRCWL_DDRCM |\
+	HRCWL_CSB_TO_CLKIN_4X1 | \
+	HRCWL_CORE_TO_CSB_2_5X1)
+
+/* 0xa0600004 */
+#define CONFIG_SYS_HRCW_HIGH (HRCWH_PCI_HOST | \
+	HRCWH_PCI_ARBITER_ENABLE | \
+	HRCWH_CORE_ENABLE | \
+	HRCWH_FROM_0X00000100 | \
+	HRCWH_BOOTSEQ_DISABLE |\
+	HRCWH_SW_WATCHDOG_DISABLE |\
+	HRCWH_ROM_LOC_LOCAL_16BIT | \
+	HRCWH_TSEC1M_IN_MII | \
+	HRCWH_BIG_ENDIAN | \
+	HRCWH_LALE_EARLY)
+
+/* System IO Config */
+#define CONFIG_SYS_SICRH	(0x01000000 | \
+				SICRH_ETSEC2_B | \
+				SICRH_ETSEC2_C | \
+				SICRH_ETSEC2_D | \
+				SICRH_ETSEC2_E | \
+				SICRH_ETSEC2_F | \
+				SICRH_ETSEC2_G | \
+				SICRH_TSOBI1 | \
+				SICRH_TSOBI2)
+				/* 0x010fff03 */
+#define CONFIG_SYS_SICRL	(SICRL_LBC | \
+				SICRL_SPI_A | \
+				SICRL_SPI_B | \
+				SICRL_SPI_C | \
+				SICRL_SPI_D | \
+				SICRL_ETSEC2_A)
+				/* 0x33fc0003) */
+
+#define CONFIG_SYS_HID0_INIT	0x000000000
+#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
+				 HID0_ENABLE_INSTRUCTION_CACHE)
+
+#define CONFIG_SYS_HID2 HID2_HBE
+
+#define CONFIG_HIGH_BATS	1	/* High BATs supported */
+
+/* DDR @ 0x00000000 */
+#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_10)
+#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | \
+				 BATU_VS | BATU_VP)
+
+#if defined(CONFIG_PCI)
+/* PCI @ 0x80000000 */
+#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_10)
+#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | \
+				BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_10 | \
+				BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | \
+				BATU_VS | BATU_VP)
+#else
+#define CONFIG_SYS_IBAT1L	(0)
+#define CONFIG_SYS_IBAT1U	(0)
+#define CONFIG_SYS_IBAT2L	(0)
+#define CONFIG_SYS_IBAT2U	(0)
+#endif
+
+/* PCI2 not supported on 8313 */
+#define CONFIG_SYS_IBAT3L	(0)
+#define CONFIG_SYS_IBAT3U	(0)
+#define CONFIG_SYS_IBAT4L	(0)
+#define CONFIG_SYS_IBAT4U	(0)
+
+/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
+#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_IMMR | BATL_PP_10 | \
+				BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_IMMR | BATU_BL_256M | BATU_VS | \
+				BATU_VP)
+
+/* stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
+#define CONFIG_SYS_IBAT6L	(0xF0000000 | BATL_PP_10 | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT6U	(0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/*  FPGA, SRAM, NAND @ 0x60000000 */
+#define CONFIG_SYS_IBAT7L	(0x60000000 | BATL_PP_10 | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT7U	(0x60000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
+#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
+#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
+#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
+#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
+#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
+#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
+#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
+#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
+#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01	/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02	/* Software reboot */
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_NETDEV		eth0
+
+#define CONFIG_HOSTNAME		ve8313
+#define CONFIG_UBOOTPATH	ve8313/u-boot.bin
+
+#define CONFIG_LOADADDR		800000
+#define CONFIG_BOOTDELAY	6	/* -1 disables auto-boot */
+#define CONFIG_BAUDRATE		115200
+
+#define XMK_STR(x)	#x
+#define MK_STR(x)	XMK_STR(x)
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"netdev=" MK_STR(CONFIG_NETDEV) "\0"				\
+	"ethprime=TSEC0\0"						\
+	"u-boot=" MK_STR(CONFIG_UBOOTPATH) "\0"				\
+	"u-boot_addr_r=100000\0"					\
+	"load=tftp ${u-boot_addr_r} ${u-boot}\0"			\
+	"update=protect off " MK_STR(CONFIG_SYS_FLASH_BASE) " +${filesize};" \
+	"erase " MK_STR(CONFIG_SYS_FLASH_BASE) " +${filesize};" \
+	"cp.b ${u-boot_addr_r} " MK_STR(CONFIG_SYS_FLASH_BASE) \
+	" ${filesize};" \
+	"protect on " MK_STR(CONFIG_SYS_FLASH_BASE) " +${filesize}\0" \
+
+#undef MK_STR
+#undef XMK_STR
+
+#endif	/* __CONFIG_H */
-- 
1.6.2.5

[U-Boot] [PATCH v2] 83xx: add support for ve8313 board

[Stefan Roese]

Hi Heiko,

On Wednesday 07 July 2010 06:28:21 Heiko Schocher wrote:
> This patch add support for the ve8313 board based on
> Freescale MPC8313 CPU.
> 
> - serial console on UART 1
> - 128 MB DDR RAM
> - 32 MB NOR Flash
> - 16 MB NAND Flash

Just checking: Is this really *only* 16 MiB NAND flash?

Cheers,
Stefan

--
DENX Software Engineering GmbH,      MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich,  Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-0 Fax: (+49)-8142-66989-80 Email: office at denx.de

[U-Boot] [PATCH v2] 83xx: add support for ve8313 board

[Heiko Schocher]

Hello Stefan,

Stefan Roese wrote:
> On Wednesday 07 July 2010 06:28:21 Heiko Schocher wrote:
>> This patch add support for the ve8313 board based on
>> Freescale MPC8313 CPU.
>>
>> - serial console on UART 1
>> - 128 MB DDR RAM
>> - 32 MB NOR Flash
>> - 16 MB NAND Flash
> 
> Just checking: Is this really *only* 16 MiB NAND flash?

Yep, it is a NAND128W3A2BN6E from Numonyx

bye
Heiko
-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

[U-Boot] [PATCH v2] 83xx: add support for ve8313 board

[Wolfgang Denk]

Dear Heiko Schocher,

In message <4C340265.3020302@invitel.hu> you wrote:
>
> changes since v1
> - environment size = sector size

Argh.  While the previous environment size of 8 KiB was indeed a bit
smallish, using 128 KiB is overkill. Keep in mind that we then have to
compute the checksum over 18 KiB as well, which just costs time - at
booting, and with every setenv you run.

I suggest to change this to a more resaobale size - say 16 KiB ?


> +/* Fixed sdram init -- doesn't use serial presence detect.
> + *
> + * This is useful for faster booting in configs where the RAM is unlikely
> + * to be changed, or for things like NAND booting where space is tight.
> + */

Incorrect multiline comment style.

The first line of the comment is misleading as one might think there
was SPD information available but we decide not to use it - actually
there is none and we cannot use it. Please fix. And since there are
no other RAM configurations on this board, I recommend to remove the
last 2 lines of the comment as well.


> +	/* set WDT pins as output */
> +	setbits_be32(&gpio->dir, VE8313_WDT_EN | VE8313_WDT_TRIG);
> +#if defined(CONFIG_HW_WATCHDOG)
> +	/* enable WDT */
> +	clrbits_be32(&gpio->dat, VE8313_WDT_EN | VE8313_WDT_TRIG);
> +#else
> +	/* disable WDT */
> +	setbits_be32(&gpio->dat, VE8313_WDT_EN | VE8313_WDT_TRIG);
> +#endif
> +	return 0;

Is this the correct order? Would it not make sense first to define
the state of the data bit before you enable the output? Otherwise
this might result in short spikes at the wrong signal level, which
here might start the watchdog by accident?

> +#if defined(CONFIG_HW_WATCHDOG)
> +void hw_watchdog_reset(void)
> +{
> +	volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
> +	volatile gpio83xx_t *gpio = (volatile gpio83xx_t *)im->gpio;
> +
> +	setbits_be32(&gpio->dat, VE8313_WDT_TRIG);
> +	clrbits_be32(&gpio->dat, VE8313_WDT_TRIG);
> +}

Is there a minimal length of the trigger pulse defined for this
watchdog? Maybe some udelay() is needed here?


> --- a/boards.cfg
> +++ b/boards.cfg
> @@ -135,6 +135,7 @@ TQM8272		powerpc	mpc8260		tqm8272		tqc
>  kmeter1		powerpc	mpc83xx		kmeter1		keymile
>  MVBLM7		powerpc	mpc83xx		mvblm7		matrix_vision
>  TQM834x		powerpc	mpc83xx		tqm834x		tqc
> +ve8313		powerpc	mpc83xx		ve8313
>  PM854		powerpc	mpc85xx		pm854
>  PM856		powerpc	mpc85xx		pm856
>  stxgp3		powerpc	mpc85xx		stxgp3		stx

This is not sorted correctly. It should go here (because of the empty
vendor field).

 SCM            powerpc mpc8260         -               siemens
 TQM8272        powerpc mpc8260         tqm8272         tqc
+ve8313         powerpc mpc83xx         ve8313
 kmeter1        powerpc mpc83xx         kmeter1         keymile
 MVBLM7         powerpc mpc83xx         mvblm7          matrix_vision

The comment in the header of the file describes how to correctly sort
this file; if you cannot parse this, just run the command in vi :-)


> +/*
> + * Manually set up DDR parameters, as this board does not
> + * seem to have the SPD connected to I2C.
> + */

"does not seem to have the SPD connected to I2C"? You know this for
sure, so please fix the comment.

> +#if !defined(CONFIG_SYS_NO_FLASH)
...
> +#else
> +#define CONFIG_SYS_FLASH_BASE		0xFE000000
> +#define CONFIG_SYS_FLASH_SIZE		32	/* size in MB */
> +#endif

I think there are no configurations of this board without NOR flash
either; please drop this as well.

> +/*
> + * TSEC
> + */
> +#define CONFIG_TSEC_ENET		/* TSEC ethernet support */
> +
> +#define CONFIG_NET_MULTI
> +
> +#define CONFIG_TSEC1

Please drop these empty lines.

> +#ifdef CONFIG_TSEC1
> +#define CONFIG_HAS_ETH0
> +#define CONFIG_TSEC1_NAME      "TSEC0"

Oops? This is TSEC1, so why do you name it "TSEC0" ?



> +/*
> + * Environment
> + */
> +#if !defined(CONFIG_SYS_RAMBOOT)
> +	#define CONFIG_ENV_IS_IN_FLASH	1
> +	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
> +						CONFIG_SYS_MONITOR_LEN)
> +	#define CONFIG_ENV_SECT_SIZE	0x20000	/* 64K(one sector) for env */

Comment and code don't match - the comment is wrong - actual sector
size is 128 KiB.

> +	/* Address and size of Redundant Environment Sector */
> +	#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
> +						CONFIG_ENV_SECT_SIZE)
> +	#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
> +#else
> +	#define CONFIG_SYS_NO_FLASH	1	/* Flash is not usable now */

Why would flash not be usable when booting from RAM?

> +	#define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in mem only */
> +	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
> +	#define CONFIG_ENV_SIZE		0x2000

I recommend to use the same CONFIG_ENV_SIZE setting for both
configurations (suggestion: use (16 << 10)).

> +#if defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_NAND_U_BOOT)
> +    #undef CONFIG_CMD_SAVEENV
> +    #undef CONFIG_CMD_LOADS
> +#endif

Why do you disable the loads command here? This makes no sense to me.


> +/*
> + * Environment Configuration
> + */
> +#define CONFIG_ENV_OVERWRITE

Please remove.

> +#define CONFIG_SYS_LOAD_ADDR   0x2000000       /* default load address */
...
> +#define CONFIG_LOADADDR		800000

Is this 800000 (= 0xc3500) or 0x800000?
and why is it different from the CONFIG_SYS_LOAD_ADDR definition above?

> +#define CONFIG_BOOTDELAY	6	/* -1 disables auto-boot */
> +#define CONFIG_BAUDRATE		115200
> +
> +#define XMK_STR(x)	#x
> +#define MK_STR(x)	XMK_STR(x)
> +
> +#define CONFIG_EXTRA_ENV_SETTINGS \
> +	"netdev=" MK_STR(CONFIG_NETDEV) "\0"				\
> +	"ethprime=TSEC0\0"						\

Use CONFIG_TSEC1_NAME here?


Best regards,

Wolfgang Denk

-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Severe culture shock results when experts from another protocol suite
[...] try to read OSI documents. The term "osified" is used to  refer
to  such  documents. [...] Any relationship to the word "ossified" is
purely intentional.                                - Marshall T. Rose

[U-Boot] [PATCH v2] 83xx: add support for ve8313 board

[Heiko Schocher]

Hello Wolfgang,

Wolfgang Denk wrote:
> In message <4C340265.3020302@invitel.hu> you wrote:
>> changes since v1
>> - environment size = sector size
> 
> Argh.  While the previous environment size of 8 KiB was indeed a bit
> smallish, using 128 KiB is overkill. Keep in mind that we then have to
> compute the checksum over 18 KiB as well, which just costs time - at
> booting, and with every setenv you run.
> 
> I suggest to change this to a more resaobale size - say 16 KiB ?

Ok, done.

>> +/* Fixed sdram init -- doesn't use serial presence detect.
>> + *
>> + * This is useful for faster booting in configs where the RAM is unlikely
>> + * to be changed, or for things like NAND booting where space is tight.
>> + */
> 
> Incorrect multiline comment style.
> 
> The first line of the comment is misleading as one might think there
> was SPD information available but we decide not to use it - actually
> there is none and we cannot use it. Please fix. And since there are
> no other RAM configurations on this board, I recommend to remove the
> last 2 lines of the comment as well.

removed.

>> +	/* set WDT pins as output */
>> +	setbits_be32(&gpio->dir, VE8313_WDT_EN | VE8313_WDT_TRIG);
>> +#if defined(CONFIG_HW_WATCHDOG)
>> +	/* enable WDT */
>> +	clrbits_be32(&gpio->dat, VE8313_WDT_EN | VE8313_WDT_TRIG);
>> +#else
>> +	/* disable WDT */
>> +	setbits_be32(&gpio->dat, VE8313_WDT_EN | VE8313_WDT_TRIG);
>> +#endif
>> +	return 0;
> 
> Is this the correct order? Would it not make sense first to define
> the state of the data bit before you enable the output? Otherwise
> this might result in short spikes at the wrong signal level, which
> here might start the watchdog by accident?

Yup, fix this.

>> +#if defined(CONFIG_HW_WATCHDOG)
>> +void hw_watchdog_reset(void)
>> +{
>> +	volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
>> +	volatile gpio83xx_t *gpio = (volatile gpio83xx_t *)im->gpio;
>> +
>> +	setbits_be32(&gpio->dat, VE8313_WDT_TRIG);
>> +	clrbits_be32(&gpio->dat, VE8313_WDT_TRIG);
>> +}
> 
> Is there a minimal length of the trigger pulse defined for this
> watchdog? Maybe some udelay() is needed here?

I check this.

>> --- a/boards.cfg
>> +++ b/boards.cfg
>> @@ -135,6 +135,7 @@ TQM8272		powerpc	mpc8260		tqm8272		tqc
>>  kmeter1		powerpc	mpc83xx		kmeter1		keymile
>>  MVBLM7		powerpc	mpc83xx		mvblm7		matrix_vision
>>  TQM834x		powerpc	mpc83xx		tqm834x		tqc
>> +ve8313		powerpc	mpc83xx		ve8313
>>  PM854		powerpc	mpc85xx		pm854
>>  PM856		powerpc	mpc85xx		pm856
>>  stxgp3		powerpc	mpc85xx		stxgp3		stx
> 
> This is not sorted correctly. It should go here (because of the empty
> vendor field).

fixed.

>  SCM            powerpc mpc8260         -               siemens
>  TQM8272        powerpc mpc8260         tqm8272         tqc
> +ve8313         powerpc mpc83xx         ve8313
>  kmeter1        powerpc mpc83xx         kmeter1         keymile
>  MVBLM7         powerpc mpc83xx         mvblm7          matrix_vision
> 
> The comment in the header of the file describes how to correctly sort
> this file; if you cannot parse this, just run the command in vi :-)
> 
> 
>> +/*
>> + * Manually set up DDR parameters, as this board does not
>> + * seem to have the SPD connected to I2C.
>> + */
> 
> "does not seem to have the SPD connected to I2C"? You know this for
> sure, so please fix the comment.

fixed

>> +#if !defined(CONFIG_SYS_NO_FLASH)
> ...
>> +#else
>> +#define CONFIG_SYS_FLASH_BASE		0xFE000000
>> +#define CONFIG_SYS_FLASH_SIZE		32	/* size in MB */
>> +#endif
> 
> I think there are no configurations of this board without NOR flash
> either; please drop this as well.

fixed.

>> +/*
>> + * TSEC
>> + */
>> +#define CONFIG_TSEC_ENET		/* TSEC ethernet support */
>> +
>> +#define CONFIG_NET_MULTI
>> +
>> +#define CONFIG_TSEC1
> 
> Please drop these empty lines.
> 
>> +#ifdef CONFIG_TSEC1
>> +#define CONFIG_HAS_ETH0
>> +#define CONFIG_TSEC1_NAME      "TSEC0"
> 
> Oops? This is TSEC1, so why do you name it "TSEC0" ?

Because this is so in all other board configs I looked.

Kim? Can you comment this?
(I think it is because to be in sync with "eth0" ...)

>> +/*
>> + * Environment
>> + */
>> +#if !defined(CONFIG_SYS_RAMBOOT)
>> +	#define CONFIG_ENV_IS_IN_FLASH	1
>> +	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
>> +						CONFIG_SYS_MONITOR_LEN)
>> +	#define CONFIG_ENV_SECT_SIZE	0x20000	/* 64K(one sector) for env */
> 
> Comment and code don't match - the comment is wrong - actual sector
> size is 128 KiB.

fixed.

>> +	/* Address and size of Redundant Environment Sector */
>> +	#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
>> +						CONFIG_ENV_SECT_SIZE)
>> +	#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
>> +#else
>> +	#define CONFIG_SYS_NO_FLASH	1	/* Flash is not usable now */
> 
> Why would flash not be usable when booting from RAM?

Argh, this is a leftover from the first hardware version, where the
flash didn;t worked. Good catch remove this.

>> +	#define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in mem only */
>> +	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
>> +	#define CONFIG_ENV_SIZE		0x2000
> 
> I recommend to use the same CONFIG_ENV_SIZE setting for both
> configurations (suggestion: use (16 << 10)).
> 
>> +#if defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_NAND_U_BOOT)
>> +    #undef CONFIG_CMD_SAVEENV
>> +    #undef CONFIG_CMD_LOADS
>> +#endif
> 
> Why do you disable the loads command here? This makes no sense to me.

yep, fixed.

>> +/*
>> + * Environment Configuration
>> + */
>> +#define CONFIG_ENV_OVERWRITE
> 
> Please remove.

done.

>> +#define CONFIG_SYS_LOAD_ADDR   0x2000000       /* default load address */
> ...
>> +#define CONFIG_LOADADDR		800000
> 
> Is this 800000 (= 0xc3500) or 0x800000?
> and why is it different from the CONFIG_SYS_LOAD_ADDR definition above?

removed this here and fixed CONFIG_SYS_LOAD_ADDR to 0x100000

>> +#define CONFIG_BOOTDELAY	6	/* -1 disables auto-boot */
>> +#define CONFIG_BAUDRATE		115200
>> +
>> +#define XMK_STR(x)	#x
>> +#define MK_STR(x)	XMK_STR(x)
>> +
>> +#define CONFIG_EXTRA_ENV_SETTINGS \
>> +	"netdev=" MK_STR(CONFIG_NETDEV) "\0"				\
>> +	"ethprime=TSEC0\0"						\
> 
> Use CONFIG_TSEC1_NAME here?

done

Thanks for the review

bye
Heiko
-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

[U-Boot] [PATCH v2] 83xx: add support for ve8313 board

[Wolfgang Denk]

Dear Heiko Schocher,

In message <4C343AE3.7060804@denx.de> you wrote:
> 
> >> +#ifdef CONFIG_TSEC1
> >> +#define CONFIG_HAS_ETH0
> >> +#define CONFIG_TSEC1_NAME      "TSEC0"
> > 
> > Oops? This is TSEC1, so why do you name it "TSEC0" ?
> 
> Because this is so in all other board configs I looked.
> 
> Kim? Can you comment this?
> (I think it is because to be in sync with "eth0" ...)

That is not a good reason to confuse the users. TSEC0 and TSEC1 are
different interfaces, and to bend names is definitely a bad idea.

Best regards,

Wolfgang Denk

-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
The trouble with our times is that the future is not what it used  to
be.                                                     - Paul Valery

[U-Boot] [PATCH v3] 83xx: add support for ve8313 board

[Heiko Schocher]

This patch add support for the ve8313 board based on
Freescale MPC8313 CPU.

- serial console on UART 1
- 128 MB DDR RAM
- 32 MB NOR Flash
- 16 MB NAND Flash
- Ethernet MII Mode over on TSEC0
- micrel ksz804 phy
- Hardware WDT MAX824

changes since v1
- Environment size = sector size
- use red. environment
- add comments from Kim Phillips
  - add MAKEALL, MAINTAINERS entry
  - Codingstyle issues fixed
  - inserted original Copyrights
  - PCI subsys vendor ID changed from 0x1057 (Motorola)
    to 0x1957 (Freescale)

changes since v2
- add comments from Wolfgang Denk
  - fix Codingstyle and some comments
  - reworked WDT reset (just toggling the WD_TRIG pin)
  - Environment size now 16KiB
  - fixed RAMBOOT version
  - fixed CONFIG_SYS_LOAD_ADDR
  - renamed CONFIG_TSEC1_NAME to TSEC1

Signed-off-by: Heiko Schocher <hs@denx.de>
---
 MAINTAINERS              |    1 +
 MAKEALL                  |    1 +
 board/ve8313/Makefile    |   50 +++++
 board/ve8313/config.mk   |    7 +
 board/ve8313/ve8313.c    |  215 +++++++++++++++++++
 boards.cfg               |    1 +
 include/configs/ve8313.h |  511 ++++++++++++++++++++++++++++++++++++++++++++++
 7 files changed, 786 insertions(+), 0 deletions(-)
 create mode 100644 board/ve8313/Makefile
 create mode 100644 board/ve8313/config.mk
 create mode 100644 board/ve8313/ve8313.c
 create mode 100644 include/configs/ve8313.h

diff --git a/MAINTAINERS b/MAINTAINERS
index d7aec98..88a3d79 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -427,6 +427,7 @@ Heiko Schocher <hs@denx.de>
 	sc3		PPC405GP
 	suen3		ARM926EJS (Kirkwood SoC)
 	uc101		MPC5200
+	ve8313		MPC8313

 Peter De Schrijver <p2@mind.be>

diff --git a/MAKEALL b/MAKEALL
index 27f8bd1..eedae60 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -379,6 +379,7 @@ LIST_83xx="		\
 	sbc8349		\
 	SIMPC8313_LP	\
 	TQM834x		\
+	ve8313		\
 	vme8349		\
 "

diff --git a/board/ve8313/Makefile b/board/ve8313/Makefile
new file mode 100644
index 0000000..c95f90e
--- /dev/null
+++ b/board/ve8313/Makefile
@@ -0,0 +1,50 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	:= $(BOARD).o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/ve8313/config.mk b/board/ve8313/config.mk
new file mode 100644
index 0000000..02dd33e
--- /dev/null
+++ b/board/ve8313/config.mk
@@ -0,0 +1,7 @@
+ifndef NAND_SPL
+sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp
+endif
+
+ifndef TEXT_BASE
+TEXT_BASE = 0xfe000000
+endif
diff --git a/board/ve8313/ve8313.c b/board/ve8313/ve8313.c
new file mode 100644
index 0000000..8ba1b19
--- /dev/null
+++ b/board/ve8313/ve8313.c
@@ -0,0 +1,215 @@
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006-2007
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * (C) Copyright 2010
+ * Heiko Schocher, DENX Software Engineering, hs at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <libfdt.h>
+#include <pci.h>
+#include <mpc83xx.h>
+#include <ns16550.h>
+#include <nand.h>
+
+#include <asm/bitops.h>
+#include <asm/io.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+extern void disable_addr_trans (void);
+extern void enable_addr_trans (void);
+
+int checkboard(void)
+{
+	puts("Board: ve8313\n");
+	return 0;
+}
+
+static long fixed_sdram(void)
+{
+	u32 msize = CONFIG_SYS_DDR_SIZE * 1024 * 1024;
+
+#ifndef CONFIG_SYS_RAMBOOT
+	volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
+	u32 msize_log2 = __ilog2(msize);
+
+	out_be32(&im->sysconf.ddrlaw[0].bar,
+		(CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000));
+	out_be32(&im->sysconf.ddrlaw[0].ar, (LBLAWAR_EN | (msize_log2 - 1)));
+	out_be32(&im->sysconf.ddrcdr, CONFIG_SYS_DDRCDR_VALUE);
+
+	/*
+	 * Erratum DDR3 requires a 50ms delay after clearing DDRCDR[DDR_cfg],
+	 * or the DDR2 controller may fail to initialize correctly.
+	 */
+	__udelay(50000);
+
+	out_be32(&im->ddr.csbnds[0].csbnds, (msize - 1) >> 24);
+	out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CONFIG);
+
+	/* Currently we use only one CS, so disable the other bank. */
+	out_be32(&im->ddr.cs_config[1], 0);
+
+	out_be32(&im->ddr.sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CNTL);
+	out_be32(&im->ddr.timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
+	out_be32(&im->ddr.timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
+	out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
+	out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
+
+	out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_SDRAM_CFG);
+
+	out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_SDRAM_CFG2);
+	out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE);
+	out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE_2);
+
+	out_be32(&im->ddr.sdram_interval, CONFIG_SYS_DDR_INTERVAL);
+	sync();
+
+	/* enable DDR controller */
+	setbits_be32(&im->ddr.sdram_cfg, SDRAM_CFG_MEM_EN);
+
+	/* now check the real size */
+	disable_addr_trans ();
+	msize = get_ram_size (CONFIG_SYS_DDR_BASE, msize);
+	enable_addr_trans ();
+#endif
+
+	return msize;
+}
+
+phys_size_t initdram(int board_type)
+{
+	volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
+	volatile fsl_lbus_t *lbc = &im->lbus;
+	u32 msize;
+
+	if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im)
+		return -1;
+
+	/* DDR SDRAM - Main SODIMM */
+	msize = fixed_sdram();
+
+	/* Local Bus setup lbcr and mrtpr */
+	out_be32(&lbc->lbcr, CONFIG_SYS_LBC_LBCR);
+	out_be32(&lbc->mrtpr, CONFIG_SYS_LBC_MRTPR);
+	sync();
+
+	/* return total bus SDRAM size(bytes)  -- DDR */
+	return msize;
+}
+
+#define VE8313_WDT_EN	0x00020000
+#define VE8313_WDT_TRIG	0x00040000
+
+int board_early_init_f (void)
+{
+	volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
+	volatile gpio83xx_t *gpio = (volatile gpio83xx_t *)im->gpio;
+
+#if defined(CONFIG_HW_WATCHDOG)
+	/* enable WDT */
+	clrbits_be32(&gpio->dat, VE8313_WDT_EN | VE8313_WDT_TRIG);
+#else
+	/* disable WDT */
+	setbits_be32(&gpio->dat, VE8313_WDT_EN | VE8313_WDT_TRIG);
+#endif
+	/* set WDT pins as output */
+	setbits_be32(&gpio->dir, VE8313_WDT_EN | VE8313_WDT_TRIG);
+
+	return 0;
+}
+
+#if defined(CONFIG_HW_WATCHDOG)
+void hw_watchdog_reset(void)
+{
+	volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
+	volatile gpio83xx_t *gpio = (volatile gpio83xx_t *)im->gpio;
+	unsigned long reg;
+
+	reg = in_be32(&gpio->dat);
+	if (reg & VE8313_WDT_TRIG)
+		clrbits_be32(&gpio->dat, VE8313_WDT_TRIG);
+	else
+		setbits_be32(&gpio->dat, VE8313_WDT_TRIG);
+}
+#endif
+
+
+#if defined(CONFIG_PCI)
+static struct pci_region pci_regions[] = {
+	{
+		bus_start: CONFIG_SYS_PCI1_MEM_BASE,
+		phys_start: CONFIG_SYS_PCI1_MEM_PHYS,
+		size: CONFIG_SYS_PCI1_MEM_SIZE,
+		flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
+	},
+	{
+		bus_start: CONFIG_SYS_PCI1_MMIO_BASE,
+		phys_start: CONFIG_SYS_PCI1_MMIO_PHYS,
+		size: CONFIG_SYS_PCI1_MMIO_SIZE,
+		flags: PCI_REGION_MEM
+	},
+	{
+		bus_start: CONFIG_SYS_PCI1_IO_BASE,
+		phys_start: CONFIG_SYS_PCI1_IO_PHYS,
+		size: CONFIG_SYS_PCI1_IO_SIZE,
+		flags: PCI_REGION_IO
+	}
+};
+
+void pci_init_board(void)
+{
+	volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
+	volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
+	volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
+	struct pci_region *reg[] = { pci_regions };
+	int warmboot;
+
+	/* Enable all 3 PCI_CLK_OUTPUTs. */
+	setbits_be32(&clk->occr, 0xe0000000);
+
+	/*
+	 * Configure PCI Local Access Windows
+	 */
+	out_be32(&pci_law[0].bar, CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR);
+	out_be32(&pci_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+	out_be32(&pci_law[1].bar, CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR);
+	out_be32(&pci_law[1].ar, LBLAWAR_EN | LBLAWAR_1MB);
+
+	warmboot = gd->bd->bi_bootflags & BOOTFLAG_WARM;
+
+	mpc83xx_pci_init(1, reg, warmboot);
+}
+#endif
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	ft_cpu_setup(blob, bd);
+#ifdef CONFIG_PCI
+	ft_pci_setup(blob, bd);
+#endif
+}
+#endif
diff --git a/boards.cfg b/boards.cfg
index 1a5cfb1..cad8ba4 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -132,6 +132,7 @@ ZPC1900		powerpc	mpc8260		zpc1900
 mgcoge		powerpc	mpc8260		-		keymile
 SCM		powerpc	mpc8260		-		siemens
 TQM8272		powerpc	mpc8260		tqm8272		tqc
+ve8313		powerpc	mpc83xx		ve8313
 kmeter1		powerpc	mpc83xx		kmeter1		keymile
 MVBLM7		powerpc	mpc83xx		mvblm7		matrix_vision
 TQM834x		powerpc	mpc83xx		tqm834x		tqc
diff --git a/include/configs/ve8313.h b/include/configs/ve8313.h
new file mode 100644
index 0000000..1589913
--- /dev/null
+++ b/include/configs/ve8313.h
@@ -0,0 +1,511 @@
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006.
+ *
+ * (C) Copyright 2010
+ * Heiko Schocher, DENX Software Engineering, hs at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+/*
+ * ve8313 board configuration file
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300		1
+#define CONFIG_MPC83xx		1
+#define CONFIG_MPC831x		1
+#define CONFIG_MPC8313		1
+#define CONFIG_VE8313		1
+
+#define CONFIG_PCI		1
+
+#define CONFIG_BOARD_EARLY_INIT_F	1
+
+/*
+ * On-board devices
+ *
+ */
+#define CONFIG_83XX_CLKIN	32000000	/* in Hz */
+
+#define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN
+
+#define CONFIG_SYS_IMMR		0xE0000000
+
+#define CONFIG_SYS_MEMTEST_START	0x00001000
+#define CONFIG_SYS_MEMTEST_END		0x07000000
+
+#define CONFIG_SYS_ACR_PIPE_DEP		3	/* Arbiter pipeline depth */
+#define CONFIG_SYS_ACR_RPTCNT		3	/* Arbiter repeat count */
+
+/*
+ * Device configurations
+ */
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_DDR_BASE		0x00000000	/* DDR is system memory*/
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+
+/*
+ * Manually set up DDR parameters, as this board does not
+ * have the SPD connected to I2C.
+ */
+#define CONFIG_SYS_DDR_SIZE		128		/* MB */
+#define CONFIG_SYS_DDR_CONFIG		( CSCONFIG_EN \
+				| CSCONFIG_AP \
+				| 0x00040000 /* TODO */ \
+				| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10 )
+				/* 0x80840102 */
+
+#define CONFIG_SYS_DDR_TIMING_3	0x00000000
+#define CONFIG_SYS_DDR_TIMING_0	( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
+				| ( 0 << TIMING_CFG0_WRT_SHIFT ) \
+				| ( 3 << TIMING_CFG0_RRT_SHIFT ) \
+				| ( 2 << TIMING_CFG0_WWT_SHIFT ) \
+				| ( 7 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \
+				| ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \
+				| ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \
+				| ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) )
+				/* 0x0e720802 */
+#define CONFIG_SYS_DDR_TIMING_1	( ( 2 << TIMING_CFG1_PRETOACT_SHIFT ) \
+				| ( 6 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
+				| ( 2 << TIMING_CFG1_ACTTORW_SHIFT ) \
+				| ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \
+				| ( 6 << TIMING_CFG1_REFREC_SHIFT ) \
+				| ( 2 << TIMING_CFG1_WRREC_SHIFT ) \
+				| ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \
+				| ( 2 << TIMING_CFG1_WRTORD_SHIFT ) )
+				/* 0x26256222 */
+#define CONFIG_SYS_DDR_TIMING_2	( ( 0 << TIMING_CFG2_ADD_LAT_SHIFT ) \
+				| ( 5 << TIMING_CFG2_CPO_SHIFT ) \
+				| ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \
+				| ( 1 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \
+				| ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \
+				| ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \
+				| ( 7 << TIMING_CFG2_FOUR_ACT_SHIFT) )
+				/* 0x029028c7 */
+#define CONFIG_SYS_DDR_INTERVAL	( ( 0x320 << SDRAM_INTERVAL_REFINT_SHIFT ) \
+				| ( 0x2000 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
+				/* 0x03202000 */
+#define CONFIG_SYS_SDRAM_CFG		( SDRAM_CFG_SREN \
+				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
+				| SDRAM_CFG_32_BE )
+				/* 0x43080000 */
+#define CONFIG_SYS_SDRAM_CFG2		0x00401000
+#define CONFIG_SYS_DDR_MODE		( ( 0x4440 << SDRAM_MODE_ESD_SHIFT ) \
+				| ( 0x0232 << SDRAM_MODE_SD_SHIFT ) )
+				/* 0x44400232 */
+#define CONFIG_SYS_DDR_MODE_2		0x8000C000
+
+#define CONFIG_SYS_DDR_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+				/*0x02000000*/
+#define CONFIG_SYS_DDRCDR_VALUE	( DDRCDR_EN \
+				| DDRCDR_PZ_NOMZ \
+				| DDRCDR_NZ_NOMZ \
+				| DDRCDR_M_ODR )
+				/* 0x73000002 */
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_CFI		/* use the Common Flash Interface */
+#define CONFIG_FLASH_CFI_DRIVER		/* use the CFI driver */
+#define CONFIG_SYS_FLASH_BASE		0xFE000000
+#define CONFIG_SYS_FLASH_SIZE		32	/* size in MB */
+#define CONFIG_SYS_FLASH_EMPTY_INFO		/* display empty sectors */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	/* buffer up multiple bytes */
+
+#define CONFIG_SYS_NOR_BR_PRELIM	(CONFIG_SYS_FLASH_BASE | \
+				(2 << BR_PS_SHIFT) |	/* 16 bit */ \
+				BR_V)			/* valid */
+#define CONFIG_SYS_NOR_OR_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
+				| OR_GPCM_CSNT \
+				| OR_GPCM_ACS_DIV4 \
+				| OR_GPCM_SCY_5 \
+				| OR_GPCM_TRLX \
+				| OR_GPCM_EAD)
+				/* 0xfe000c55 */
+
+#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_LBLAWAR0_PRELIM	0x80000018 /* 32 MB window size */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1		/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	256		/* sectors per dev */
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE	/* start of monitor */
+
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_SYS_INIT_RAM_LOCK	1
+#define CONFIG_SYS_INIT_RAM_ADDR	0xFD000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END		0x1000	/* End of used area in RAM*/
+
+#define CONFIG_SYS_GBL_DATA_SIZE	0x100	/* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - \
+					 CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
+#define CONFIG_SYS_MONITOR_LEN		(384 * 1024)
+#define CONFIG_SYS_MALLOC_LEN		(512 * 1024)
+
+/*
+ * Local Bus LCRR and LBCR regs
+ */
+#define CONFIG_SYS_LCRR_EADC	LCRR_EADC_3
+#define CONFIG_SYS_LCRR_CLKDIV	LCRR_CLKDIV_2
+
+#define CONFIG_SYS_LBC_LBCR	0x00040000
+
+#define CONFIG_SYS_LBC_MRTPR	0x20000000
+
+/*
+ * NAND settings
+ */
+#define CONFIG_SYS_NAND_BASE		0x61000000
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND 1
+#define CONFIG_NAND_FSL_ELBC 1
+#define CONFIG_SYS_NAND_BLOCK_SIZE 16384
+
+#define CONFIG_SYS_NAND_BR_PRELIM	( CONFIG_SYS_NAND_BASE \
+				| BR_PS_8		\
+				| BR_DECC_CHK_GEN	\
+				| BR_MS_FCM		\
+				| BR_V )	/* valid */
+				/* 0x61000c21 */
+#define CONFIG_SYS_NAND_OR_PRELIM	(0xffff8000 \
+				| OR_FCM_BCTLD \
+				| OR_FCM_CHT \
+				| OR_FCM_SCY_2 \
+				| OR_FCM_RST \
+				| OR_FCM_TRLX)
+				/* 0xffff90ac */
+
+#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM
+#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM
+#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM
+#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM
+
+#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_NAND_BASE
+#define CONFIG_SYS_LBLAWAR1_PRELIM	0x8000000E	/* 32KB  */
+
+#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
+#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM
+
+/* CS2 NvRAM */
+#define CONFIG_SYS_BR2_PRELIM	(0x60000000	\
+				| BR_PS_8	\
+				| BR_V)
+				/* 0x60000801 */
+#define CONFIG_SYS_OR2_PRELIM	(0xfffe0000	\
+				| OR_GPCM_CSNT	\
+				| OR_GPCM_XACS	\
+				| OR_GPCM_SCY_3 \
+				| OR_GPCM_TRLX \
+				| OR_GPCM_EHTR \
+				| OR_GPCM_EAD)
+				/* 0xfffe0937 */
+/* local bus read write buffer mapping SRAM@0x64000000 */
+#define CONFIG_SYS_BR3_PRELIM	(0x62000000	\
+				| BR_PS_16	\
+				| BR_V)
+				/* 0x62001001 */
+
+#define CONFIG_SYS_OR3_PRELIM	(0xfe000000	\
+				| OR_GPCM_CSNT	\
+				| OR_GPCM_XACS	\
+				| OR_GPCM_SCY_15 \
+				| OR_GPCM_TRLX \
+				| OR_GPCM_EHTR \
+				| OR_GPCM_EAD)
+				/* 0xfe0009f7 */
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT	1
+#define CONFIG_OF_BOARD_SETUP	1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX	1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+#if defined(CONFIG_PCI)
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI1_MMIO_BASE	0x90000000
+#define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
+#define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI1_IO_BASE	0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS	0xE2000000
+#define CONFIG_SYS_PCI1_IO_SIZE	0x00100000	/* 1M */
+
+#define CONFIG_PCI_PNP		/* do pci plug-and-play */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957	/* Freescale */
+#endif
+
+/*
+ * TSEC
+ */
+#define CONFIG_TSEC_ENET		/* TSEC ethernet support */
+
+#define CONFIG_NET_MULTI
+
+#define CONFIG_TSEC1
+#ifdef CONFIG_TSEC1
+#define CONFIG_HAS_ETH0
+#define CONFIG_TSEC1_NAME	"TSEC1"
+#define CONFIG_SYS_TSEC1_OFFSET	0x24000
+#define TSEC1_PHY_ADDR		0x01
+#define TSEC1_FLAGS		0
+#define TSEC1_PHYIDX		0
+#endif
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME			"TSEC1"
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_IS_IN_FLASH	1
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + \
+					CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SECT_SIZE	0x20000	/* 128K(one sector) for env */
+#define CONFIG_ENV_SIZE		0x4000
+/* Address and size of Redundant Environment Sector */
+#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
+					CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_PCI
+
+#define CONFIG_CMDLINE_EDITING 1
+#define CONFIG_AUTO_COMPLETE	/* add autocompletion support   */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address */
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
+
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS	16		/* max number of cmd args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE /* Boot arg Buffer size */
+#define CONFIG_SYS_HZ		1000		/* 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
+
+/* 0x64050000 */
+#define CONFIG_SYS_HRCW_LOW (\
+	0x20000000 /* reserved, must be set */ |\
+	HRCWL_DDRCM |\
+	HRCWL_CSB_TO_CLKIN_4X1 | \
+	HRCWL_CORE_TO_CSB_2_5X1)
+
+/* 0xa0600004 */
+#define CONFIG_SYS_HRCW_HIGH (HRCWH_PCI_HOST | \
+	HRCWH_PCI_ARBITER_ENABLE | \
+	HRCWH_CORE_ENABLE | \
+	HRCWH_FROM_0X00000100 | \
+	HRCWH_BOOTSEQ_DISABLE |\
+	HRCWH_SW_WATCHDOG_DISABLE |\
+	HRCWH_ROM_LOC_LOCAL_16BIT | \
+	HRCWH_TSEC1M_IN_MII | \
+	HRCWH_BIG_ENDIAN | \
+	HRCWH_LALE_EARLY)
+
+/* System IO Config */
+#define CONFIG_SYS_SICRH	(0x01000000 | \
+				SICRH_ETSEC2_B | \
+				SICRH_ETSEC2_C | \
+				SICRH_ETSEC2_D | \
+				SICRH_ETSEC2_E | \
+				SICRH_ETSEC2_F | \
+				SICRH_ETSEC2_G | \
+				SICRH_TSOBI1 | \
+				SICRH_TSOBI2)
+				/* 0x010fff03 */
+#define CONFIG_SYS_SICRL	(SICRL_LBC | \
+				SICRL_SPI_A | \
+				SICRL_SPI_B | \
+				SICRL_SPI_C | \
+				SICRL_SPI_D | \
+				SICRL_ETSEC2_A)
+				/* 0x33fc0003) */
+
+#define CONFIG_SYS_HID0_INIT	0x000000000
+#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
+				 HID0_ENABLE_INSTRUCTION_CACHE)
+
+#define CONFIG_SYS_HID2 HID2_HBE
+
+#define CONFIG_HIGH_BATS	1	/* High BATs supported */
+
+/* DDR @ 0x00000000 */
+#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_10)
+#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | \
+				 BATU_VS | BATU_VP)
+
+#if defined(CONFIG_PCI)
+/* PCI @ 0x80000000 */
+#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_10)
+#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | \
+				BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_10 | \
+				BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | \
+				BATU_VS | BATU_VP)
+#else
+#define CONFIG_SYS_IBAT1L	(0)
+#define CONFIG_SYS_IBAT1U	(0)
+#define CONFIG_SYS_IBAT2L	(0)
+#define CONFIG_SYS_IBAT2U	(0)
+#endif
+
+/* PCI2 not supported on 8313 */
+#define CONFIG_SYS_IBAT3L	(0)
+#define CONFIG_SYS_IBAT3U	(0)
+#define CONFIG_SYS_IBAT4L	(0)
+#define CONFIG_SYS_IBAT4U	(0)
+
+/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
+#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_IMMR | BATL_PP_10 | \
+				BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_IMMR | BATU_BL_256M | BATU_VS | \
+				BATU_VP)
+
+/* stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
+#define CONFIG_SYS_IBAT6L	(0xF0000000 | BATL_PP_10 | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT6U	(0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/*  FPGA, SRAM, NAND @ 0x60000000 */
+#define CONFIG_SYS_IBAT7L	(0x60000000 | BATL_PP_10 | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT7U	(0x60000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
+#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
+#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
+#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
+#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
+#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
+#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
+#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
+#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
+#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01	/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02	/* Software reboot */
+
+#define CONFIG_NETDEV		eth0
+
+#define CONFIG_HOSTNAME		ve8313
+#define CONFIG_UBOOTPATH	ve8313/u-boot.bin
+
+#define CONFIG_BOOTDELAY	6	/* -1 disables auto-boot */
+#define CONFIG_BAUDRATE		115200
+
+#define XMK_STR(x)	#x
+#define MK_STR(x)	XMK_STR(x)
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"netdev=" MK_STR(CONFIG_NETDEV) "\0"				\
+	"ethprime=" MK_STR(CONFIG_TSEC1_NAME) "\0"			\
+	"u-boot=" MK_STR(CONFIG_UBOOTPATH) "\0"				\
+	"u-boot_addr_r=100000\0"					\
+	"load=tftp ${u-boot_addr_r} ${u-boot}\0"			\
+	"update=protect off " MK_STR(CONFIG_SYS_FLASH_BASE) " +${filesize};" \
+	"erase " MK_STR(CONFIG_SYS_FLASH_BASE) " +${filesize};" \
+	"cp.b ${u-boot_addr_r} " MK_STR(CONFIG_SYS_FLASH_BASE) \
+	" ${filesize};" \
+	"protect on " MK_STR(CONFIG_SYS_FLASH_BASE) " +${filesize}\0" \
+
+#undef MK_STR
+#undef XMK_STR
+
+#endif	/* __CONFIG_H */
-- 
1.6.2.5


-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

[U-Boot] [PATCH v3] 83xx: add support for ve8313 board

[Kim Phillips]

On Wed, 7 Jul 2010 12:26:34 +0200
Heiko Schocher <hs@denx.de> wrote:

> This patch add support for the ve8313 board based on
> Freescale MPC8313 CPU.

> Signed-off-by: Heiko Schocher <hs@denx.de>
> ---

Applied.

Thanks,

Kim