* [U-Boot] Please pull u-boot-staging/trini@ti.com
@ 2012-08-10 16:10 Tom Rini
2012-08-10 20:06 ` Wolfgang Denk
0 siblings, 1 reply; 18+ messages in thread
From: Tom Rini @ 2012-08-10 16:10 UTC (permalink / raw)
To: u-boot
Hello Albert and Wolfgang,
To try and ease the backlog of ARM changes, I've taken the liberty of
grabbing the Snowball and Raspberry Pi model B board support patches and
putting them into the staging tree. Both of these series have been
posted for some time and been reviewed. Wolfgang, if you would like to
wait for Albert to pick up this request, that's fine. I just wanted to
make sure the submitters weren't left waiting. Thanks!
The following changes since commit 4d3c95f5ea7c737a21cd6b9c59435ee693b3f127:
zfs: Add ZFS filesystem support (2012-08-09 23:42:20 +0200)
are available in the git repository at:
git://git.denx.de/u-boot-staging trini at ti.com
for you to fetch changes up to bcf2c9ef2877440033e3032fbd597be32728020c:
ARM: add Raspberry Pi model B board, using BCM2835 SoC (2012-08-10 08:57:29 -0700)
----------------------------------------------------------------
John Rigby (1):
u8500: Separating mmc config parameters from driver
Mathieu J. Poirier (10):
snowball: Add support for ux500 based snowball board
u8500: Moving prcmu to cpu directory
snowball: Adding architecture dependent initialisation
snowball: Adding CPU clock initialisation
snowball: Moving to ux500.v2 addess scheme for PRCMU access
snowball: applying power to LAN and GBF controllers
u8500: Moving processor-specific functions to cpu area.
u8500: Enabling power to MMC device on AB8500 V2
armv7: Adding cpu specific cache managmenent
snowball: Adding board specific cache cleanup routine
Stephen Warren (4):
README: fix references to config_cmd_default.h
ARM: arm1176: enable instruction cache in arch_cpu_init()
ARM: add basic support for the Broadcom BCM2835 SoC
ARM: add Raspberry Pi model B board, using BCM2835 SoC
MAINTAINERS | 8 +
README | 4 +-
arch/arm/cpu/arm1176/bcm2835/Makefile | 37 +
arch/arm/cpu/arm1176/bcm2835/config.mk | 19 +
arch/arm/cpu/arm1176/bcm2835/lowlevel_init.S | 19 +
arch/arm/cpu/arm1176/bcm2835/reset.c | 35 +
arch/arm/cpu/arm1176/bcm2835/timer.c | 55 ++
arch/arm/cpu/arm1176/cpu.c | 7 +
arch/arm/cpu/armv7/cpu.c | 8 +
arch/arm/cpu/armv7/u8500/Makefile | 2 +-
arch/arm/cpu/armv7/u8500/clock.c | 34 +
arch/arm/cpu/armv7/u8500/cpu.c | 192 +++++
.../arm/cpu/armv7}/u8500/prcmu.c | 128 +++-
arch/arm/include/asm/arch-bcm2835/gpio.h | 66 ++
arch/arm/include/asm/arch-bcm2835/timer.h | 37 +
arch/arm/include/asm/arch-bcm2835/wdog.h | 36 +
arch/arm/include/asm/arch-u8500/clock.h | 5 +-
arch/arm/include/asm/arch-u8500/db8500_gpio.h | 42 ++
arch/arm/include/asm/arch-u8500/db8500_pincfg.h | 170 +++++
arch/arm/include/asm/arch-u8500/hardware.h | 33 +-
.../arm/include/asm/arch-u8500/prcmu.h | 35 +-
arch/arm/include/asm/arch-u8500/sys_proto.h | 1 +
board/armltd/vexpress/ca9x4_ct_vxp.c | 21 +-
board/raspberrypi/rpi_b/Makefile | 34 +
board/raspberrypi/rpi_b/rpi_b.c | 34 +
board/st-ericsson/snowball/Makefile | 49 ++
board/st-ericsson/snowball/db8500_pins.h | 745 ++++++++++++++++++++
board/st-ericsson/snowball/snowball.c | 348 +++++++++
board/st-ericsson/u8500/Makefile | 2 +-
board/st-ericsson/u8500/u8500_href.c | 99 +--
boards.cfg | 2 +
drivers/gpio/Makefile | 2 +
drivers/gpio/bcm2835_gpio.c | 89 +++
drivers/gpio/db8500_gpio.c | 221 ++++++
drivers/mmc/arm_pl180_mmci.c | 131 ++--
drivers/mmc/arm_pl180_mmci.h | 27 +-
drivers/serial/serial_pl01x.c | 2 +
include/configs/rpi_b.h | 104 +++
include/configs/snowball.h | 266 +++++++
39 files changed, 2937 insertions(+), 212 deletions(-)
create mode 100644 arch/arm/cpu/arm1176/bcm2835/Makefile
create mode 100644 arch/arm/cpu/arm1176/bcm2835/config.mk
create mode 100644 arch/arm/cpu/arm1176/bcm2835/lowlevel_init.S
create mode 100644 arch/arm/cpu/arm1176/bcm2835/reset.c
create mode 100644 arch/arm/cpu/arm1176/bcm2835/timer.c
create mode 100644 arch/arm/cpu/armv7/u8500/cpu.c
rename {board/st-ericsson => arch/arm/cpu/armv7}/u8500/prcmu.c (58%)
create mode 100644 arch/arm/include/asm/arch-bcm2835/gpio.h
create mode 100644 arch/arm/include/asm/arch-bcm2835/timer.h
create mode 100644 arch/arm/include/asm/arch-bcm2835/wdog.h
create mode 100644 arch/arm/include/asm/arch-u8500/db8500_gpio.h
create mode 100644 arch/arm/include/asm/arch-u8500/db8500_pincfg.h
rename board/st-ericsson/u8500/prcmu-fw.h => arch/arm/include/asm/arch-u8500/prcmu.h (55%)
create mode 100644 board/raspberrypi/rpi_b/Makefile
create mode 100644 board/raspberrypi/rpi_b/rpi_b.c
create mode 100644 board/st-ericsson/snowball/Makefile
create mode 100644 board/st-ericsson/snowball/db8500_pins.h
create mode 100644 board/st-ericsson/snowball/snowball.c
create mode 100644 drivers/gpio/bcm2835_gpio.c
create mode 100644 drivers/gpio/db8500_gpio.c
create mode 100644 include/configs/rpi_b.h
create mode 100644 include/configs/snowball.h
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20120810/c57e26e6/attachment.pgp>
^ permalink raw reply [flat|nested] 18+ messages in thread* [U-Boot] Please pull u-boot-staging/trini@ti.com
2012-08-10 16:10 [U-Boot] Please pull u-boot-staging/trini@ti.com Tom Rini
@ 2012-08-10 20:06 ` Wolfgang Denk
2012-08-14 0:04 ` Albert ARIBAUD
0 siblings, 1 reply; 18+ messages in thread
From: Wolfgang Denk @ 2012-08-10 20:06 UTC (permalink / raw)
To: u-boot
Dear Tom,
In message <20120810161021.GG3306@bill-the-cat> you wrote:
>
> To try and ease the backlog of ARM changes, I've taken the liberty of
> grabbing the Snowball and Raspberry Pi model B board support patches and
> putting them into the staging tree. Both of these series have been
> posted for some time and been reviewed. Wolfgang, if you would like to
> wait for Albert to pick up this request, that's fine. I just wanted to
> make sure the submitters weren't left waiting. Thanks!
Thanks, highly appreciated.
As this contains a lot of ARM, indeed I would like to wait for
Albert's ACK or pulling (whichever he prefers).
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Politics: A strife of interests masquerading as a contest of
principles. The conduct of public affairs for private advantage.
- Ambrose Bierce
^ permalink raw reply [flat|nested] 18+ messages in thread
* [U-Boot] Please pull u-boot-staging/trini@ti.com
2012-08-10 20:06 ` Wolfgang Denk
@ 2012-08-14 0:04 ` Albert ARIBAUD
2012-08-14 1:06 ` Albert ARIBAUD
0 siblings, 1 reply; 18+ messages in thread
From: Albert ARIBAUD @ 2012-08-14 0:04 UTC (permalink / raw)
To: u-boot
Hi Tom,
On Fri, 10 Aug 2012 22:06:59 +0200, Wolfgang Denk <wd@denx.de> wrote:
> Dear Tom,
>
> In message <20120810161021.GG3306@bill-the-cat> you wrote:
> >
> > To try and ease the backlog of ARM changes, I've taken the liberty
> > of grabbing the Snowball and Raspberry Pi model B board support
> > patches and putting them into the staging tree. Both of these
> > series have been posted for some time and been reviewed. Wolfgang,
> > if you would like to wait for Albert to pick up this request,
> > that's fine. I just wanted to make sure the submitters weren't
> > left waiting. Thanks!
>
> Thanks, highly appreciated.
>
> As this contains a lot of ARM, indeed I would like to wait for
> Albert's ACK or pulling (whichever he prefers).
>
> Best regards,
>
> Wolfgang Denk
>
Applied to u-boot-arm/master, thanks!
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 18+ messages in thread
* [U-Boot] Please pull u-boot-staging/trini@ti.com
2012-08-14 0:04 ` Albert ARIBAUD
@ 2012-08-14 1:06 ` Albert ARIBAUD
2012-08-14 12:58 ` Mathieu Poirier
2012-08-15 16:51 ` Tom Rini
0 siblings, 2 replies; 18+ messages in thread
From: Albert ARIBAUD @ 2012-08-14 1:06 UTC (permalink / raw)
To: u-boot
Hi Albert,
On Tue, 14 Aug 2012 02:04:15 +0200, Albert ARIBAUD (U-Boot)
<albert.u.boot@aribaud.net> wrote:
> Hi Tom,
>
> On Fri, 10 Aug 2012 22:06:59 +0200, Wolfgang Denk <wd@denx.de> wrote:
>
> > Dear Tom,
> >
> > In message <20120810161021.GG3306@bill-the-cat> you wrote:
> > >
> > > To try and ease the backlog of ARM changes, I've taken the liberty
> > > of grabbing the Snowball and Raspberry Pi model B board support
> > > patches and putting them into the staging tree. Both of these
> > > series have been posted for some time and been reviewed.
> > > Wolfgang, if you would like to wait for Albert to pick up this
> > > request, that's fine. I just wanted to make sure the submitters
> > > weren't left waiting. Thanks!
> >
> > Thanks, highly appreciated.
> >
> > As this contains a lot of ARM, indeed I would like to wait for
> > Albert's ACK or pulling (whichever he prefers).
> >
> > Best regards,
> >
> > Wolfgang Denk
> >
>
> Applied to u-boot-arm/master, thanks!
But I might hold this a little, as commit "snowball: Adding
architecture dependent initialisation"
7e2b895eb5aa10890910eed8921d042d13b828c0 seems to play bad with my
stock Ubuntu 12.04 GCC on u8500_href:
uboot at lilith:~/src/u-boot-arm$ git checkout
f917361b988f69ddc0dbe2bd2beb93b296065b70^ HEAD is now at 1b5d8d5...
u8500: Moving prcmu to cpu directory uboot at lilith:~/src/u-boot-arm$
LANG=C ./MAKEALL u8500_href Configuring for u8500_href board...
text data bss dec
hex filename 139584 4408 221728
365720 59498 ./u-boot
--------------------- SUMMARY ----------------------------
Boards compiled: 1
----------------------------------------------------------
uboot at lilith:~/src/u-boot-arm$ git checkout
f917361b988f69ddc0dbe2bd2beb93b296065b70 Previous HEAD position was
1b5d8d5... u8500: Moving prcmu to cpu directory HEAD is now at
f917361... snowball: Adding architecture dependent initialisation
uboot at lilith:~/src/u-boot-arm$ LANG=C ./MAKEALL u8500_href Configuring
for u8500_href board... text data bss
dec hex filename 139744 4408
221696 365848 59518 ./u-boot u8500_href.c:45:0:
warning: "PRCMU_BASE" redefined [enabled by
default] /home/uboot/src/u-boot-arm/include/asm/arch/prcmu.h:30:0:
note: this is the location of the previous definition
--------------------- SUMMARY ----------------------------
Boards compiled: 1
Boards with warnings but no errors: 1 ( u8500_href )
----------------------------------------------------------
Granted, this is only a warning, but I'd like to see it fixed.
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 18+ messages in thread
* [U-Boot] Please pull u-boot-staging/trini@ti.com
2012-08-14 1:06 ` Albert ARIBAUD
@ 2012-08-14 12:58 ` Mathieu Poirier
2012-08-15 16:51 ` Tom Rini
1 sibling, 0 replies; 18+ messages in thread
From: Mathieu Poirier @ 2012-08-14 12:58 UTC (permalink / raw)
To: u-boot
I will fix this right away.
Mathieu.
On 12-08-13 07:06 PM, Albert ARIBAUD (U-Boot) wrote:
> Hi Albert,
>
> On Tue, 14 Aug 2012 02:04:15 +0200, Albert ARIBAUD (U-Boot)
> <albert.u.boot@aribaud.net> wrote:
>
>> Hi Tom,
>>
>> On Fri, 10 Aug 2012 22:06:59 +0200, Wolfgang Denk <wd@denx.de> wrote:
>>
>>> Dear Tom,
>>>
>>> In message <20120810161021.GG3306@bill-the-cat> you wrote:
>>>>
>>>> To try and ease the backlog of ARM changes, I've taken the liberty
>>>> of grabbing the Snowball and Raspberry Pi model B board support
>>>> patches and putting them into the staging tree. Both of these
>>>> series have been posted for some time and been reviewed.
>>>> Wolfgang, if you would like to wait for Albert to pick up this
>>>> request, that's fine. I just wanted to make sure the submitters
>>>> weren't left waiting. Thanks!
>>>
>>> Thanks, highly appreciated.
>>>
>>> As this contains a lot of ARM, indeed I would like to wait for
>>> Albert's ACK or pulling (whichever he prefers).
>>>
>>> Best regards,
>>>
>>> Wolfgang Denk
>>>
>>
>> Applied to u-boot-arm/master, thanks!
>
> But I might hold this a little, as commit "snowball: Adding
> architecture dependent initialisation"
> 7e2b895eb5aa10890910eed8921d042d13b828c0 seems to play bad with my
> stock Ubuntu 12.04 GCC on u8500_href:
>
> uboot at lilith:~/src/u-boot-arm$ git checkout
> f917361b988f69ddc0dbe2bd2beb93b296065b70^ HEAD is now at 1b5d8d5...
> u8500: Moving prcmu to cpu directory uboot at lilith:~/src/u-boot-arm$
> LANG=C ./MAKEALL u8500_href Configuring for u8500_href board...
> text data bss dec
> hex filename 139584 4408 221728
> 365720 59498 ./u-boot
>
> --------------------- SUMMARY ----------------------------
> Boards compiled: 1
> ----------------------------------------------------------
> uboot at lilith:~/src/u-boot-arm$ git checkout
> f917361b988f69ddc0dbe2bd2beb93b296065b70 Previous HEAD position was
> 1b5d8d5... u8500: Moving prcmu to cpu directory HEAD is now at
> f917361... snowball: Adding architecture dependent initialisation
> uboot at lilith:~/src/u-boot-arm$ LANG=C ./MAKEALL u8500_href Configuring
> for u8500_href board... text data bss
> dec hex filename 139744 4408
> 221696 365848 59518 ./u-boot u8500_href.c:45:0:
> warning: "PRCMU_BASE" redefined [enabled by
> default] /home/uboot/src/u-boot-arm/include/asm/arch/prcmu.h:30:0:
> note: this is the location of the previous definition
>
> --------------------- SUMMARY ----------------------------
> Boards compiled: 1
> Boards with warnings but no errors: 1 ( u8500_href )
> ----------------------------------------------------------
>
> Granted, this is only a warning, but I'd like to see it fixed.
>
> Amicalement,
^ permalink raw reply [flat|nested] 18+ messages in thread
* [U-Boot] Please pull u-boot-staging/trini@ti.com
2012-08-14 1:06 ` Albert ARIBAUD
2012-08-14 12:58 ` Mathieu Poirier
@ 2012-08-15 16:51 ` Tom Rini
1 sibling, 0 replies; 18+ messages in thread
From: Tom Rini @ 2012-08-15 16:51 UTC (permalink / raw)
To: u-boot
On Tue, Aug 14, 2012 at 03:06:17AM +0200, Albert ARIBAUD wrote:
> Hi Albert,
>
> On Tue, 14 Aug 2012 02:04:15 +0200, Albert ARIBAUD (U-Boot)
> <albert.u.boot@aribaud.net> wrote:
>
> > Hi Tom,
> >
> > On Fri, 10 Aug 2012 22:06:59 +0200, Wolfgang Denk <wd@denx.de> wrote:
> >
> > > Dear Tom,
> > >
> > > In message <20120810161021.GG3306@bill-the-cat> you wrote:
> > > >
> > > > To try and ease the backlog of ARM changes, I've taken the liberty
> > > > of grabbing the Snowball and Raspberry Pi model B board support
> > > > patches and putting them into the staging tree. Both of these
> > > > series have been posted for some time and been reviewed.
> > > > Wolfgang, if you would like to wait for Albert to pick up this
> > > > request, that's fine. I just wanted to make sure the submitters
> > > > weren't left waiting. Thanks!
> > >
> > > Thanks, highly appreciated.
> > >
> > > As this contains a lot of ARM, indeed I would like to wait for
> > > Albert's ACK or pulling (whichever he prefers).
> > >
> > > Best regards,
> > >
> > > Wolfgang Denk
> > >
> >
> > Applied to u-boot-arm/master, thanks!
>
> But I might hold this a little, as commit "snowball: Adding
> architecture dependent initialisation"
> 7e2b895eb5aa10890910eed8921d042d13b828c0 seems to play bad with my
> stock Ubuntu 12.04 GCC on u8500_href:
>
> uboot at lilith:~/src/u-boot-arm$ git checkout
> f917361b988f69ddc0dbe2bd2beb93b296065b70^ HEAD is now at 1b5d8d5...
> u8500: Moving prcmu to cpu directory uboot at lilith:~/src/u-boot-arm$
> LANG=C ./MAKEALL u8500_href Configuring for u8500_href board...
> text data bss dec
> hex filename 139584 4408 221728
> 365720 59498 ./u-boot
>
> --------------------- SUMMARY ----------------------------
> Boards compiled: 1
> ----------------------------------------------------------
> uboot at lilith:~/src/u-boot-arm$ git checkout
> f917361b988f69ddc0dbe2bd2beb93b296065b70 Previous HEAD position was
> 1b5d8d5... u8500: Moving prcmu to cpu directory HEAD is now at
> f917361... snowball: Adding architecture dependent initialisation
> uboot at lilith:~/src/u-boot-arm$ LANG=C ./MAKEALL u8500_href Configuring
> for u8500_href board... text data bss
> dec hex filename 139744 4408
> 221696 365848 59518 ./u-boot u8500_href.c:45:0:
> warning: "PRCMU_BASE" redefined [enabled by
> default] /home/uboot/src/u-boot-arm/include/asm/arch/prcmu.h:30:0:
> note: this is the location of the previous definition
>
> --------------------- SUMMARY ----------------------------
> Boards compiled: 1
> Boards with warnings but no errors: 1 ( u8500_href )
> ----------------------------------------------------------
>
> Granted, this is only a warning, but I'd like to see it fixed.
I've taken Mathieu's updated patch and pushed the series again to
u-boot-staging/trini at ti.com. A git reset --hard
a1cd53c6b6e2e7fbf4ffa20d3548646e4c94efe5 and then pull of my tree will
get things back in shape. I've done a MAKEALL -s u8500 and it's fine
now and I'm kicking off a -a arm.
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20120815/71ae1d03/attachment.pgp>
^ permalink raw reply [flat|nested] 18+ messages in thread
* [U-Boot] Please pull u-boot-staging/trini@ti.com
@ 2012-09-04 16:08 Tom Rini
2012-09-04 19:09 ` Albert ARIBAUD
0 siblings, 1 reply; 18+ messages in thread
From: Tom Rini @ 2012-09-04 16:08 UTC (permalink / raw)
To: u-boot
Hello,
The following changes since commit a9f1a4893364ddbb8b7942cded91d4c17c4f5948:
lsxl: support power switch (2012-09-03 17:48:51 +0530)
are available in the git repository at:
git://git.denx.de/u-boot-staging trini at ti.com
for you to fetch changes up to e62b008fe341030f4a80a09b66952bba65027b70:
integrator: break out common config (2012-09-04 08:51:13 -0700)
----------------------------------------------------------------
Linus Walleij (1):
integrator: break out common config
include/configs/integrator-common.h | 103 +++++++++++++++++++++++++++++++
include/configs/integratorap.h | 49 +--------------
include/configs/integratorcp.h | 115 ++---------------------------------
3 files changed, 111 insertions(+), 156 deletions(-)
create mode 100644 include/configs/integrator-common.h
A build of all of the integrator boards is fine still.
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20120904/79e240cb/attachment.pgp>
^ permalink raw reply [flat|nested] 18+ messages in thread* [U-Boot] Please pull u-boot-staging/trini@ti.com
2012-09-04 16:08 Tom Rini
@ 2012-09-04 19:09 ` Albert ARIBAUD
0 siblings, 0 replies; 18+ messages in thread
From: Albert ARIBAUD @ 2012-09-04 19:09 UTC (permalink / raw)
To: u-boot
Hi Tom,
On Tue, 4 Sep 2012 09:08:26 -0700, Tom Rini <trini@ti.com> wrote:
> Hello,
>
> The following changes since commit
> a9f1a4893364ddbb8b7942cded91d4c17c4f5948:
>
> lsxl: support power switch (2012-09-03 17:48:51 +0530)
>
> are available in the git repository at:
>
> git://git.denx.de/u-boot-staging trini at ti.com
>
> for you to fetch changes up to
> e62b008fe341030f4a80a09b66952bba65027b70:
>
> integrator: break out common config (2012-09-04 08:51:13 -0700)
>
> ----------------------------------------------------------------
> Linus Walleij (1):
> integrator: break out common config
>
> include/configs/integrator-common.h | 103
> +++++++++++++++++++++++++++++++ include/configs/integratorap.h
> | 49 +-------------- include/configs/integratorcp.h | 115
> ++--------------------------------- 3 files changed, 111
> insertions(+), 156 deletions(-) create mode 100644
> include/configs/integrator-common.h
>
> A build of all of the integrator boards is fine still.
>
Applied (as a trivial fast-forwarding merge) to u-boot-arm/master,
thanks!
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 18+ messages in thread
* [U-Boot] Please pull u-boot-staging/trini@ti.com
@ 2012-08-31 23:27 Tom Rini
2012-09-01 7:39 ` Albert ARIBAUD
0 siblings, 1 reply; 18+ messages in thread
From: Tom Rini @ 2012-08-31 23:27 UTC (permalink / raw)
To: u-boot
Hello,
The following changes since commit 092592c3b79aa3974ea12ae4f408db7679e6a109:
ARM: add Raspberry Pi model B board, using BCM2835 SoC (2012-08-30 08:50:50 +0200)
are available in the git repository at:
git://git.denx.de/u-boot-staging trini at ti.com
for you to fetch changes up to a2d4138ccbe6c38ac0db21ac900f05fadfdf0f02:
ARM: Remove unused stack and irq config defines (2012-08-31 15:44:13 -0700)
----------------------------------------------------------------
Rob Herring (1):
ARM: Remove unused stack and irq config defines
Tetsuyuki Kobayashi (1):
arm: bugfix: save_boot_params_default accesses uninitalized stack when -O0
arch/arm/cpu/armv7/cpu.c | 7 -------
arch/arm/cpu/armv7/start.S | 14 ++++++++++++++
include/configs/SX1.h | 13 -------------
include/configs/VCMA9.h | 12 ------------
include/configs/a320evb.h | 13 -------------
include/configs/actux1.h | 6 ------
include/configs/actux2.h | 6 ------
include/configs/actux3.h | 7 -------
include/configs/actux4.h | 6 ------
include/configs/adp-ag101.h | 7 -------
include/configs/adp-ag101p.h | 7 -------
include/configs/adp-ag102.h | 7 -------
include/configs/afeb9260.h | 5 -----
include/configs/am335x_evm.h | 3 ---
include/configs/am3517_crane.h | 8 --------
include/configs/am3517_evm.h | 8 --------
include/configs/apollon.h | 8 --------
include/configs/at91rm9200ek.h | 3 ---
include/configs/at91sam9260ek.h | 7 -------
include/configs/at91sam9261ek.h | 7 -------
include/configs/at91sam9263ek.h | 5 -----
include/configs/at91sam9m10g45ek.h | 7 -------
include/configs/at91sam9rlek.h | 5 -----
include/configs/balloon3.h | 9 ---------
include/configs/ca9x4_ct_vxp.h | 7 -------
include/configs/calimain.h | 1 -
include/configs/cam_enc_4xx.h | 2 --
include/configs/cm4008.h | 13 -------------
include/configs/cm41xx.h | 13 -------------
include/configs/cm_t35.h | 8 --------
include/configs/colibri_pxa270.h | 11 -----------
include/configs/cpu9260.h | 7 -------
include/configs/cpuat91.h | 10 ----------
include/configs/da830evm.h | 2 --
include/configs/da850evm.h | 1 -
include/configs/davinci_dm355evm.h | 2 --
include/configs/davinci_dm355leopard.h | 2 --
include/configs/davinci_dm365evm.h | 2 --
include/configs/davinci_dm6467evm.h | 2 --
include/configs/davinci_dvevm.h | 2 --
include/configs/davinci_schmoogie.h | 2 --
include/configs/davinci_sffsdr.h | 2 --
include/configs/davinci_sonata.h | 2 --
include/configs/devkit3250.h | 1 -
include/configs/devkit8000.h | 4 ----
include/configs/dig297.h | 12 ------------
include/configs/dvlhost.h | 7 -------
include/configs/ea20.h | 1 -
include/configs/eb_cpux9k2.h | 2 --
include/configs/edminiv2.h | 1 -
include/configs/efikamx.h | 7 -------
include/configs/enbw_cmc.h | 1 -
include/configs/ethernut5.h | 5 ++---
include/configs/flea3.h | 8 --------
include/configs/hawkboard.h | 1 -
include/configs/highbank.h | 11 -----------
include/configs/igep00x0.h | 7 -------
include/configs/ima3-mx53.h | 3 ---
include/configs/imx27lite-common.h | 1 -
include/configs/imx31_litekit.h | 7 -------
include/configs/imx31_phycore.h | 7 -------
include/configs/integratorap.h | 11 -----------
include/configs/integratorcp.h | 11 -----------
include/configs/jadecpu.h | 7 -------
include/configs/jornada.h | 7 -------
include/configs/km/km_arm.h | 1 -
include/configs/lubbock.h | 12 ------------
include/configs/m28evk.h | 1 -
include/configs/mcx.h | 7 -------
include/configs/meesc.h | 7 -------
include/configs/mv-common.h | 1 -
include/configs/mx1ads.h | 12 ------------
include/configs/mx25pdk.h | 3 ---
include/configs/mx28evk.h | 1 -
include/configs/mx31ads.h | 7 -------
include/configs/mx31pdk.h | 7 -------
include/configs/mx35pdk.h | 8 --------
include/configs/mx51evk.h | 7 -------
include/configs/mx53ard.h | 3 ---
include/configs/mx53evk.h | 3 ---
include/configs/mx53loco.h | 3 ---
include/configs/mx53smd.h | 3 ---
include/configs/mx6qarm2.h | 1 -
include/configs/mx6qsabrelite.h | 1 -
include/configs/nhk8815.h | 6 ------
include/configs/ns9750dev.h | 4 ----
include/configs/omap1510inn.h | 13 -------------
include/configs/omap2420h4.h | 12 ------------
include/configs/omap3_beagle.h | 8 --------
include/configs/omap3_evm_common.h | 8 --------
include/configs/omap3_logic.h | 9 ---------
include/configs/omap3_mvblx.h | 8 --------
include/configs/omap3_overo.h | 8 --------
include/configs/omap3_pandora.h | 8 --------
include/configs/omap3_sdp3430.h | 8 --------
include/configs/omap3_zoom1.h | 8 --------
include/configs/omap3_zoom2.h | 8 --------
include/configs/omap4_common.h | 12 ------------
include/configs/omap5912osk.h | 13 -------------
include/configs/omap5_evm.h | 12 ------------
include/configs/omap730p2.h | 14 --------------
include/configs/origen.h | 8 --------
include/configs/otc570.h | 7 -------
include/configs/palmld.h | 9 ---------
include/configs/palmtc.h | 9 ---------
include/configs/pdnb3.h | 11 -----------
include/configs/pm9261.h | 7 -------
include/configs/pm9263.h | 7 -------
include/configs/pm9g45.h | 6 ------
include/configs/pxa255_idp.h | 13 -------------
include/configs/qong.h | 6 ------
include/configs/s5p_goni.h | 3 ---
include/configs/s5pc210_universal.h | 3 ---
include/configs/sbc35_a9g20.h | 6 ------
include/configs/scb9328.h | 8 --------
include/configs/smdk2410.h | 13 -------------
include/configs/smdk5250.h | 3 ---
include/configs/smdk6400.h | 7 -------
include/configs/smdkc100.h | 7 -------
include/configs/smdkv310.h | 8 --------
include/configs/snapper9260.h | 2 --
include/configs/spear-common.h | 8 --------
include/configs/tam3517-common.h | 7 -------
include/configs/tegra2-common.h | 6 ------
include/configs/tnetv107x_evm.h | 1 -
include/configs/tny_a9260.h | 7 -------
include/configs/top9000.h | 5 -----
include/configs/trats.h | 3 ---
include/configs/tricorder.h | 4 ----
include/configs/trizepsiv.h | 13 -------------
include/configs/tt01.h | 3 ---
include/configs/tx25.h | 1 -
include/configs/u8500_href.h | 10 ----------
include/configs/vct.h | 1 -
include/configs/versatile.h | 11 -----------
include/configs/vision2.h | 5 -----
include/configs/vl_ma2sc.h | 9 ---------
include/configs/vpac270.h | 8 --------
include/configs/xaeniax.h | 15 ---------------
include/configs/zipitz2.h | 10 ----------
include/configs/zmx25.h | 1 -
141 files changed, 16 insertions(+), 895 deletions(-)
A MAKEALL -a arm (not MAKEALL arm) has been run and no changes seen
overall.
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20120831/d53ea4b8/attachment.pgp>
^ permalink raw reply [flat|nested] 18+ messages in thread* [U-Boot] Please pull u-boot-staging/trini@ti.com
2012-08-31 23:27 Tom Rini
@ 2012-09-01 7:39 ` Albert ARIBAUD
0 siblings, 0 replies; 18+ messages in thread
From: Albert ARIBAUD @ 2012-09-01 7:39 UTC (permalink / raw)
To: u-boot
Hi Tom,
On Fri, 31 Aug 2012 16:27:18 -0700, Tom Rini <trini@ti.com> wrote:
> Hello,
>
> The following changes since commit
> 092592c3b79aa3974ea12ae4f408db7679e6a109:
>
> ARM: add Raspberry Pi model B board, using BCM2835 SoC (2012-08-30
> 08:50:50 +0200)
>
> are available in the git repository at:
>
> git://git.denx.de/u-boot-staging trini at ti.com
>
> for you to fetch changes up to
> a2d4138ccbe6c38ac0db21ac900f05fadfdf0f02:
>
> ARM: Remove unused stack and irq config defines (2012-08-31
> 15:44:13 -0700)
>
> ----------------------------------------------------------------
> Rob Herring (1):
> ARM: Remove unused stack and irq config defines
>
> Tetsuyuki Kobayashi (1):
> arm: bugfix: save_boot_params_default accesses uninitalized
> stack when -O0
>
> arch/arm/cpu/armv7/cpu.c | 7 -------
> arch/arm/cpu/armv7/start.S | 14 ++++++++++++++
> include/configs/SX1.h | 13 -------------
> include/configs/VCMA9.h | 12 ------------
> include/configs/a320evb.h | 13 -------------
> include/configs/actux1.h | 6 ------
> include/configs/actux2.h | 6 ------
> include/configs/actux3.h | 7 -------
> include/configs/actux4.h | 6 ------
> include/configs/adp-ag101.h | 7 -------
> include/configs/adp-ag101p.h | 7 -------
> include/configs/adp-ag102.h | 7 -------
> include/configs/afeb9260.h | 5 -----
> include/configs/am335x_evm.h | 3 ---
> include/configs/am3517_crane.h | 8 --------
> include/configs/am3517_evm.h | 8 --------
> include/configs/apollon.h | 8 --------
> include/configs/at91rm9200ek.h | 3 ---
> include/configs/at91sam9260ek.h | 7 -------
> include/configs/at91sam9261ek.h | 7 -------
> include/configs/at91sam9263ek.h | 5 -----
> include/configs/at91sam9m10g45ek.h | 7 -------
> include/configs/at91sam9rlek.h | 5 -----
> include/configs/balloon3.h | 9 ---------
> include/configs/ca9x4_ct_vxp.h | 7 -------
> include/configs/calimain.h | 1 -
> include/configs/cam_enc_4xx.h | 2 --
> include/configs/cm4008.h | 13 -------------
> include/configs/cm41xx.h | 13 -------------
> include/configs/cm_t35.h | 8 --------
> include/configs/colibri_pxa270.h | 11 -----------
> include/configs/cpu9260.h | 7 -------
> include/configs/cpuat91.h | 10 ----------
> include/configs/da830evm.h | 2 --
> include/configs/da850evm.h | 1 -
> include/configs/davinci_dm355evm.h | 2 --
> include/configs/davinci_dm355leopard.h | 2 --
> include/configs/davinci_dm365evm.h | 2 --
> include/configs/davinci_dm6467evm.h | 2 --
> include/configs/davinci_dvevm.h | 2 --
> include/configs/davinci_schmoogie.h | 2 --
> include/configs/davinci_sffsdr.h | 2 --
> include/configs/davinci_sonata.h | 2 --
> include/configs/devkit3250.h | 1 -
> include/configs/devkit8000.h | 4 ----
> include/configs/dig297.h | 12 ------------
> include/configs/dvlhost.h | 7 -------
> include/configs/ea20.h | 1 -
> include/configs/eb_cpux9k2.h | 2 --
> include/configs/edminiv2.h | 1 -
> include/configs/efikamx.h | 7 -------
> include/configs/enbw_cmc.h | 1 -
> include/configs/ethernut5.h | 5 ++---
> include/configs/flea3.h | 8 --------
> include/configs/hawkboard.h | 1 -
> include/configs/highbank.h | 11 -----------
> include/configs/igep00x0.h | 7 -------
> include/configs/ima3-mx53.h | 3 ---
> include/configs/imx27lite-common.h | 1 -
> include/configs/imx31_litekit.h | 7 -------
> include/configs/imx31_phycore.h | 7 -------
> include/configs/integratorap.h | 11 -----------
> include/configs/integratorcp.h | 11 -----------
> include/configs/jadecpu.h | 7 -------
> include/configs/jornada.h | 7 -------
> include/configs/km/km_arm.h | 1 -
> include/configs/lubbock.h | 12 ------------
> include/configs/m28evk.h | 1 -
> include/configs/mcx.h | 7 -------
> include/configs/meesc.h | 7 -------
> include/configs/mv-common.h | 1 -
> include/configs/mx1ads.h | 12 ------------
> include/configs/mx25pdk.h | 3 ---
> include/configs/mx28evk.h | 1 -
> include/configs/mx31ads.h | 7 -------
> include/configs/mx31pdk.h | 7 -------
> include/configs/mx35pdk.h | 8 --------
> include/configs/mx51evk.h | 7 -------
> include/configs/mx53ard.h | 3 ---
> include/configs/mx53evk.h | 3 ---
> include/configs/mx53loco.h | 3 ---
> include/configs/mx53smd.h | 3 ---
> include/configs/mx6qarm2.h | 1 -
> include/configs/mx6qsabrelite.h | 1 -
> include/configs/nhk8815.h | 6 ------
> include/configs/ns9750dev.h | 4 ----
> include/configs/omap1510inn.h | 13 -------------
> include/configs/omap2420h4.h | 12 ------------
> include/configs/omap3_beagle.h | 8 --------
> include/configs/omap3_evm_common.h | 8 --------
> include/configs/omap3_logic.h | 9 ---------
> include/configs/omap3_mvblx.h | 8 --------
> include/configs/omap3_overo.h | 8 --------
> include/configs/omap3_pandora.h | 8 --------
> include/configs/omap3_sdp3430.h | 8 --------
> include/configs/omap3_zoom1.h | 8 --------
> include/configs/omap3_zoom2.h | 8 --------
> include/configs/omap4_common.h | 12 ------------
> include/configs/omap5912osk.h | 13 -------------
> include/configs/omap5_evm.h | 12 ------------
> include/configs/omap730p2.h | 14 --------------
> include/configs/origen.h | 8 --------
> include/configs/otc570.h | 7 -------
> include/configs/palmld.h | 9 ---------
> include/configs/palmtc.h | 9 ---------
> include/configs/pdnb3.h | 11 -----------
> include/configs/pm9261.h | 7 -------
> include/configs/pm9263.h | 7 -------
> include/configs/pm9g45.h | 6 ------
> include/configs/pxa255_idp.h | 13 -------------
> include/configs/qong.h | 6 ------
> include/configs/s5p_goni.h | 3 ---
> include/configs/s5pc210_universal.h | 3 ---
> include/configs/sbc35_a9g20.h | 6 ------
> include/configs/scb9328.h | 8 --------
> include/configs/smdk2410.h | 13 -------------
> include/configs/smdk5250.h | 3 ---
> include/configs/smdk6400.h | 7 -------
> include/configs/smdkc100.h | 7 -------
> include/configs/smdkv310.h | 8 --------
> include/configs/snapper9260.h | 2 --
> include/configs/spear-common.h | 8 --------
> include/configs/tam3517-common.h | 7 -------
> include/configs/tegra2-common.h | 6 ------
> include/configs/tnetv107x_evm.h | 1 -
> include/configs/tny_a9260.h | 7 -------
> include/configs/top9000.h | 5 -----
> include/configs/trats.h | 3 ---
> include/configs/tricorder.h | 4 ----
> include/configs/trizepsiv.h | 13 -------------
> include/configs/tt01.h | 3 ---
> include/configs/tx25.h | 1 -
> include/configs/u8500_href.h | 10 ----------
> include/configs/vct.h | 1 -
> include/configs/versatile.h | 11 -----------
> include/configs/vision2.h | 5 -----
> include/configs/vl_ma2sc.h | 9 ---------
> include/configs/vpac270.h | 8 --------
> include/configs/xaeniax.h | 15 ---------------
> include/configs/zipitz2.h | 10 ----------
> include/configs/zmx25.h | 1 -
> 141 files changed, 16 insertions(+), 895 deletions(-)
>
> A MAKEALL -a arm (not MAKEALL arm) has been run and no changes seen
> overall.
>
Applied to u-boot-arm/master, thanks!
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 18+ messages in thread
* [U-Boot] Please pull u-boot-staging/trini@ti.com
@ 2012-08-17 21:52 Tom Rini
2012-08-18 6:28 ` Albert ARIBAUD
0 siblings, 1 reply; 18+ messages in thread
From: Tom Rini @ 2012-08-17 21:52 UTC (permalink / raw)
To: u-boot
Hello,
This replaces my previous pull-request and is new warning free on
MAKEALL -a arm for ELDK4.2/5.1/5.2.1.
The following changes since commit 4d3c95f5ea7c737a21cd6b9c59435ee693b3f127:
zfs: Add ZFS filesystem support (2012-08-09 23:42:20 +0200)
are available in the git repository at:
git://git.denx.de/u-boot-staging trini at ti.com
for you to fetch changes up to 5d26e4de33fab7b132e8a8036ac54176f537d79f:
ARM: add Raspberry Pi model B board, using BCM2835 SoC (2012-08-15 09:43:47 -0700)
----------------------------------------------------------------
John Rigby (1):
u8500: Separating mmc config parameters from driver
Mathieu J. Poirier (10):
snowball: Add support for ux500 based snowball board
u8500: Moving prcmu to cpu directory
snowball: Adding architecture dependent initialisation
snowball: Adding CPU clock initialisation
snowball: Moving to ux500.v2 addess scheme for PRCMU access
snowball: applying power to LAN and GBF controllers
u8500: Moving processor-specific functions to cpu area.
u8500: Enabling power to MMC device on AB8500 V2
armv7: Adding cpu specific cache managmenent
snowball: Adding board specific cache cleanup routine
Stephen Warren (4):
README: fix references to config_cmd_default.h
ARM: arm1176: enable instruction cache in arch_cpu_init()
ARM: add basic support for the Broadcom BCM2835 SoC
ARM: add Raspberry Pi model B board, using BCM2835 SoC
MAINTAINERS | 8 +
README | 4 +-
arch/arm/cpu/arm1176/bcm2835/Makefile | 37 +
arch/arm/cpu/arm1176/bcm2835/config.mk | 19 +
arch/arm/cpu/arm1176/bcm2835/lowlevel_init.S | 19 +
arch/arm/cpu/arm1176/bcm2835/reset.c | 35 +
arch/arm/cpu/arm1176/bcm2835/timer.c | 55 ++
arch/arm/cpu/arm1176/cpu.c | 7 +
arch/arm/cpu/armv7/cpu.c | 8 +
arch/arm/cpu/armv7/u8500/Makefile | 2 +-
arch/arm/cpu/armv7/u8500/clock.c | 34 +
arch/arm/cpu/armv7/u8500/cpu.c | 192 +++++
.../arm/cpu/armv7}/u8500/prcmu.c | 128 +++-
arch/arm/include/asm/arch-bcm2835/gpio.h | 66 ++
arch/arm/include/asm/arch-bcm2835/timer.h | 37 +
arch/arm/include/asm/arch-bcm2835/wdog.h | 36 +
arch/arm/include/asm/arch-u8500/clock.h | 5 +-
arch/arm/include/asm/arch-u8500/db8500_gpio.h | 42 ++
arch/arm/include/asm/arch-u8500/db8500_pincfg.h | 170 +++++
arch/arm/include/asm/arch-u8500/hardware.h | 33 +-
.../arm/include/asm/arch-u8500/prcmu.h | 35 +-
arch/arm/include/asm/arch-u8500/sys_proto.h | 1 +
board/armltd/vexpress/ca9x4_ct_vxp.c | 21 +-
board/raspberrypi/rpi_b/Makefile | 34 +
board/raspberrypi/rpi_b/rpi_b.c | 34 +
board/st-ericsson/snowball/Makefile | 49 ++
board/st-ericsson/snowball/db8500_pins.h | 745 ++++++++++++++++++++
board/st-ericsson/snowball/snowball.c | 348 +++++++++
board/st-ericsson/u8500/Makefile | 2 +-
board/st-ericsson/u8500/u8500_href.c | 100 +--
boards.cfg | 2 +
drivers/gpio/Makefile | 2 +
drivers/gpio/bcm2835_gpio.c | 89 +++
drivers/gpio/db8500_gpio.c | 221 ++++++
drivers/mmc/arm_pl180_mmci.c | 131 ++--
drivers/mmc/arm_pl180_mmci.h | 27 +-
drivers/serial/serial_pl01x.c | 2 +
include/configs/rpi_b.h | 104 +++
include/configs/snowball.h | 266 +++++++
39 files changed, 2937 insertions(+), 213 deletions(-)
create mode 100644 arch/arm/cpu/arm1176/bcm2835/Makefile
create mode 100644 arch/arm/cpu/arm1176/bcm2835/config.mk
create mode 100644 arch/arm/cpu/arm1176/bcm2835/lowlevel_init.S
create mode 100644 arch/arm/cpu/arm1176/bcm2835/reset.c
create mode 100644 arch/arm/cpu/arm1176/bcm2835/timer.c
create mode 100644 arch/arm/cpu/armv7/u8500/cpu.c
rename {board/st-ericsson => arch/arm/cpu/armv7}/u8500/prcmu.c (58%)
create mode 100644 arch/arm/include/asm/arch-bcm2835/gpio.h
create mode 100644 arch/arm/include/asm/arch-bcm2835/timer.h
create mode 100644 arch/arm/include/asm/arch-bcm2835/wdog.h
create mode 100644 arch/arm/include/asm/arch-u8500/db8500_gpio.h
create mode 100644 arch/arm/include/asm/arch-u8500/db8500_pincfg.h
rename board/st-ericsson/u8500/prcmu-fw.h => arch/arm/include/asm/arch-u8500/prcmu.h (55%)
create mode 100644 board/raspberrypi/rpi_b/Makefile
create mode 100644 board/raspberrypi/rpi_b/rpi_b.c
create mode 100644 board/st-ericsson/snowball/Makefile
create mode 100644 board/st-ericsson/snowball/db8500_pins.h
create mode 100644 board/st-ericsson/snowball/snowball.c
create mode 100644 drivers/gpio/bcm2835_gpio.c
create mode 100644 drivers/gpio/db8500_gpio.c
create mode 100644 include/configs/rpi_b.h
create mode 100644 include/configs/snowball.h
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20120817/14d5a510/attachment.pgp>
^ permalink raw reply [flat|nested] 18+ messages in thread* [U-Boot] Please pull u-boot-staging/trini@ti.com
2012-08-17 21:52 Tom Rini
@ 2012-08-18 6:28 ` Albert ARIBAUD
2012-08-18 14:15 ` Tom Rini
0 siblings, 1 reply; 18+ messages in thread
From: Albert ARIBAUD @ 2012-08-18 6:28 UTC (permalink / raw)
To: u-boot
Hi Tom,
On Fri, 17 Aug 2012 14:52:01 -0700, Tom Rini <trini@ti.com> wrote:
> Hello,
>
> This replaces my previous pull-request and is new warning free on
> MAKEALL -a arm for ELDK4.2/5.1/5.2.1.
>
> The following changes since commit
> 4d3c95f5ea7c737a21cd6b9c59435ee693b3f127:
>
> zfs: Add ZFS filesystem support (2012-08-09 23:42:20 +0200)
>
> are available in the git repository at:
>
> git://git.denx.de/u-boot-staging trini at ti.com
>
> for you to fetch changes up to
> 5d26e4de33fab7b132e8a8036ac54176f537d79f:
>
> ARM: add Raspberry Pi model B board, using BCM2835 SoC (2012-08-15
> 09:43:47 -0700)
>
> ----------------------------------------------------------------
> John Rigby (1):
> u8500: Separating mmc config parameters from driver
>
> Mathieu J. Poirier (10):
> snowball: Add support for ux500 based snowball board
> u8500: Moving prcmu to cpu directory
> snowball: Adding architecture dependent initialisation
> snowball: Adding CPU clock initialisation
> snowball: Moving to ux500.v2 addess scheme for PRCMU access
> snowball: applying power to LAN and GBF controllers
> u8500: Moving processor-specific functions to cpu area.
> u8500: Enabling power to MMC device on AB8500 V2
> armv7: Adding cpu specific cache managmenent
> snowball: Adding board specific cache cleanup routine
>
> Stephen Warren (4):
> README: fix references to config_cmd_default.h
> ARM: arm1176: enable instruction cache in arch_cpu_init()
> ARM: add basic support for the Broadcom BCM2835 SoC
> ARM: add Raspberry Pi model B board, using BCM2835 SoC
>
> MAINTAINERS | 8 +
> README | 4 +-
> arch/arm/cpu/arm1176/bcm2835/Makefile | 37 +
> arch/arm/cpu/arm1176/bcm2835/config.mk | 19 +
> arch/arm/cpu/arm1176/bcm2835/lowlevel_init.S | 19 +
> arch/arm/cpu/arm1176/bcm2835/reset.c | 35 +
> arch/arm/cpu/arm1176/bcm2835/timer.c | 55 ++
> arch/arm/cpu/arm1176/cpu.c | 7 +
> arch/arm/cpu/armv7/cpu.c | 8 +
> arch/arm/cpu/armv7/u8500/Makefile | 2 +-
> arch/arm/cpu/armv7/u8500/clock.c | 34 +
> arch/arm/cpu/armv7/u8500/cpu.c | 192 +++++
> .../arm/cpu/armv7}/u8500/prcmu.c | 128 +++-
> arch/arm/include/asm/arch-bcm2835/gpio.h | 66 ++
> arch/arm/include/asm/arch-bcm2835/timer.h | 37 +
> arch/arm/include/asm/arch-bcm2835/wdog.h | 36 +
> arch/arm/include/asm/arch-u8500/clock.h | 5 +-
> arch/arm/include/asm/arch-u8500/db8500_gpio.h | 42 ++
> arch/arm/include/asm/arch-u8500/db8500_pincfg.h | 170 +++++
> arch/arm/include/asm/arch-u8500/hardware.h | 33 +-
> .../arm/include/asm/arch-u8500/prcmu.h | 35 +-
> arch/arm/include/asm/arch-u8500/sys_proto.h | 1 +
> board/armltd/vexpress/ca9x4_ct_vxp.c | 21 +-
> board/raspberrypi/rpi_b/Makefile | 34 +
> board/raspberrypi/rpi_b/rpi_b.c | 34 +
> board/st-ericsson/snowball/Makefile | 49 ++
> board/st-ericsson/snowball/db8500_pins.h | 745
> ++++++++++++++++++++
> board/st-ericsson/snowball/snowball.c | 348 +++++++++
> board/st-ericsson/u8500/Makefile | 2 +-
> board/st-ericsson/u8500/u8500_href.c | 100 +--
> boards.cfg | 2 +
> drivers/gpio/Makefile | 2 +
> drivers/gpio/bcm2835_gpio.c | 89 +++
> drivers/gpio/db8500_gpio.c | 221 ++++++
> drivers/mmc/arm_pl180_mmci.c | 131 ++--
> drivers/mmc/arm_pl180_mmci.h | 27 +-
> drivers/serial/serial_pl01x.c | 2 +
> include/configs/rpi_b.h | 104 +++
> include/configs/snowball.h | 266 +++++++ 39
> files changed, 2937 insertions(+), 213 deletions(-) create mode
> 100644 arch/arm/cpu/arm1176/bcm2835/Makefile create mode 100644
> arch/arm/cpu/arm1176/bcm2835/config.mk create mode 100644
> arch/arm/cpu/arm1176/bcm2835/lowlevel_init.S create mode 100644
> arch/arm/cpu/arm1176/bcm2835/reset.c create mode 100644
> arch/arm/cpu/arm1176/bcm2835/timer.c create mode 100644
> arch/arm/cpu/armv7/u8500/cpu.c rename {board/st-ericsson =>
> arch/arm/cpu/armv7}/u8500/prcmu.c (58%) create mode 100644
> arch/arm/include/asm/arch-bcm2835/gpio.h create mode 100644
> arch/arm/include/asm/arch-bcm2835/timer.h create mode 100644
> arch/arm/include/asm/arch-bcm2835/wdog.h create mode 100644
> arch/arm/include/asm/arch-u8500/db8500_gpio.h create mode 100644
> arch/arm/include/asm/arch-u8500/db8500_pincfg.h rename
> board/st-ericsson/u8500/prcmu-fw.h =>
> arch/arm/include/asm/arch-u8500/prcmu.h (55%) create mode 100644
> board/raspberrypi/rpi_b/Makefile create mode 100644
> board/raspberrypi/rpi_b/rpi_b.c create mode 100644
> board/st-ericsson/snowball/Makefile create mode 100644
> board/st-ericsson/snowball/db8500_pins.h create mode 100644
> board/st-ericsson/snowball/snowball.c create mode 100644
> drivers/gpio/bcm2835_gpio.c create mode 100644
> drivers/gpio/db8500_gpio.c create mode 100644 include/configs/rpi_b.h
> create mode 100644 include/configs/snowball.h
>
Are you sure you want me to only pull the top 15 patches of
u-boot-staging/trini at ti.com, but not the tens of ones that that are
below it in u-boot-staging/master? These are nowhere else, especially
not in u-boot/master, so I am wondering why your your request takes
staging/master as its base.
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 18+ messages in thread* [U-Boot] Please pull u-boot-staging/trini@ti.com
2012-08-18 6:28 ` Albert ARIBAUD
@ 2012-08-18 14:15 ` Tom Rini
2012-08-18 20:53 ` Tom Rini
0 siblings, 1 reply; 18+ messages in thread
From: Tom Rini @ 2012-08-18 14:15 UTC (permalink / raw)
To: u-boot
On Sat, Aug 18, 2012 at 08:28:55AM +0200, Albert ARIBAUD wrote:
> Hi Tom,
>
> On Fri, 17 Aug 2012 14:52:01 -0700, Tom Rini <trini@ti.com> wrote:
>
> > Hello,
> >
> > This replaces my previous pull-request and is new warning free on
> > MAKEALL -a arm for ELDK4.2/5.1/5.2.1.
> >
> > The following changes since commit
> > 4d3c95f5ea7c737a21cd6b9c59435ee693b3f127:
> >
> > zfs: Add ZFS filesystem support (2012-08-09 23:42:20 +0200)
> >
> > are available in the git repository at:
> >
> > git://git.denx.de/u-boot-staging trini at ti.com
> >
> > for you to fetch changes up to
> > 5d26e4de33fab7b132e8a8036ac54176f537d79f:
> >
> > ARM: add Raspberry Pi model B board, using BCM2835 SoC (2012-08-15
> > 09:43:47 -0700)
> >
> > ----------------------------------------------------------------
> > John Rigby (1):
> > u8500: Separating mmc config parameters from driver
> >
> > Mathieu J. Poirier (10):
> > snowball: Add support for ux500 based snowball board
> > u8500: Moving prcmu to cpu directory
> > snowball: Adding architecture dependent initialisation
> > snowball: Adding CPU clock initialisation
> > snowball: Moving to ux500.v2 addess scheme for PRCMU access
> > snowball: applying power to LAN and GBF controllers
> > u8500: Moving processor-specific functions to cpu area.
> > u8500: Enabling power to MMC device on AB8500 V2
> > armv7: Adding cpu specific cache managmenent
> > snowball: Adding board specific cache cleanup routine
> >
> > Stephen Warren (4):
> > README: fix references to config_cmd_default.h
> > ARM: arm1176: enable instruction cache in arch_cpu_init()
> > ARM: add basic support for the Broadcom BCM2835 SoC
> > ARM: add Raspberry Pi model B board, using BCM2835 SoC
> >
> > MAINTAINERS | 8 +
> > README | 4 +-
> > arch/arm/cpu/arm1176/bcm2835/Makefile | 37 +
> > arch/arm/cpu/arm1176/bcm2835/config.mk | 19 +
> > arch/arm/cpu/arm1176/bcm2835/lowlevel_init.S | 19 +
> > arch/arm/cpu/arm1176/bcm2835/reset.c | 35 +
> > arch/arm/cpu/arm1176/bcm2835/timer.c | 55 ++
> > arch/arm/cpu/arm1176/cpu.c | 7 +
> > arch/arm/cpu/armv7/cpu.c | 8 +
> > arch/arm/cpu/armv7/u8500/Makefile | 2 +-
> > arch/arm/cpu/armv7/u8500/clock.c | 34 +
> > arch/arm/cpu/armv7/u8500/cpu.c | 192 +++++
> > .../arm/cpu/armv7}/u8500/prcmu.c | 128 +++-
> > arch/arm/include/asm/arch-bcm2835/gpio.h | 66 ++
> > arch/arm/include/asm/arch-bcm2835/timer.h | 37 +
> > arch/arm/include/asm/arch-bcm2835/wdog.h | 36 +
> > arch/arm/include/asm/arch-u8500/clock.h | 5 +-
> > arch/arm/include/asm/arch-u8500/db8500_gpio.h | 42 ++
> > arch/arm/include/asm/arch-u8500/db8500_pincfg.h | 170 +++++
> > arch/arm/include/asm/arch-u8500/hardware.h | 33 +-
> > .../arm/include/asm/arch-u8500/prcmu.h | 35 +-
> > arch/arm/include/asm/arch-u8500/sys_proto.h | 1 +
> > board/armltd/vexpress/ca9x4_ct_vxp.c | 21 +-
> > board/raspberrypi/rpi_b/Makefile | 34 +
> > board/raspberrypi/rpi_b/rpi_b.c | 34 +
> > board/st-ericsson/snowball/Makefile | 49 ++
> > board/st-ericsson/snowball/db8500_pins.h | 745
> > ++++++++++++++++++++
> > board/st-ericsson/snowball/snowball.c | 348 +++++++++
> > board/st-ericsson/u8500/Makefile | 2 +-
> > board/st-ericsson/u8500/u8500_href.c | 100 +--
> > boards.cfg | 2 +
> > drivers/gpio/Makefile | 2 +
> > drivers/gpio/bcm2835_gpio.c | 89 +++
> > drivers/gpio/db8500_gpio.c | 221 ++++++
> > drivers/mmc/arm_pl180_mmci.c | 131 ++--
> > drivers/mmc/arm_pl180_mmci.h | 27 +-
> > drivers/serial/serial_pl01x.c | 2 +
> > include/configs/rpi_b.h | 104 +++
> > include/configs/snowball.h | 266 +++++++ 39
> > files changed, 2937 insertions(+), 213 deletions(-) create mode
> > 100644 arch/arm/cpu/arm1176/bcm2835/Makefile create mode 100644
> > arch/arm/cpu/arm1176/bcm2835/config.mk create mode 100644
> > arch/arm/cpu/arm1176/bcm2835/lowlevel_init.S create mode 100644
> > arch/arm/cpu/arm1176/bcm2835/reset.c create mode 100644
> > arch/arm/cpu/arm1176/bcm2835/timer.c create mode 100644
> > arch/arm/cpu/armv7/u8500/cpu.c rename {board/st-ericsson =>
> > arch/arm/cpu/armv7}/u8500/prcmu.c (58%) create mode 100644
> > arch/arm/include/asm/arch-bcm2835/gpio.h create mode 100644
> > arch/arm/include/asm/arch-bcm2835/timer.h create mode 100644
> > arch/arm/include/asm/arch-bcm2835/wdog.h create mode 100644
> > arch/arm/include/asm/arch-u8500/db8500_gpio.h create mode 100644
> > arch/arm/include/asm/arch-u8500/db8500_pincfg.h rename
> > board/st-ericsson/u8500/prcmu-fw.h =>
> > arch/arm/include/asm/arch-u8500/prcmu.h (55%) create mode 100644
> > board/raspberrypi/rpi_b/Makefile create mode 100644
> > board/raspberrypi/rpi_b/rpi_b.c create mode 100644
> > board/st-ericsson/snowball/Makefile create mode 100644
> > board/st-ericsson/snowball/db8500_pins.h create mode 100644
> > board/st-ericsson/snowball/snowball.c create mode 100644
> > drivers/gpio/bcm2835_gpio.c create mode 100644
> > drivers/gpio/db8500_gpio.c create mode 100644 include/configs/rpi_b.h
> > create mode 100644 include/configs/snowball.h
>
> Are you sure you want me to only pull the top 15 patches of
> u-boot-staging/trini at ti.com, but not the tens of ones that that are
> below it in u-boot-staging/master? These are nowhere else, especially
> not in u-boot/master, so I am wondering why your your request takes
> staging/master as its base.
I don't see any patches like that. And I did a quick re-confirm of what
is in trini at ti.com and that's what I want to replace the commits in
u-boot-arm/master from before.
--
Tom
^ permalink raw reply [flat|nested] 18+ messages in thread* [U-Boot] Please pull u-boot-staging/trini@ti.com
2012-08-18 14:15 ` Tom Rini
@ 2012-08-18 20:53 ` Tom Rini
2012-08-30 7:44 ` Albert ARIBAUD
0 siblings, 1 reply; 18+ messages in thread
From: Tom Rini @ 2012-08-18 20:53 UTC (permalink / raw)
To: u-boot
On Sat, Aug 18, 2012 at 07:15:56AM -0700, Tom Rini wrote:
> On Sat, Aug 18, 2012 at 08:28:55AM +0200, Albert ARIBAUD wrote:
> > Hi Tom,
> >
> > On Fri, 17 Aug 2012 14:52:01 -0700, Tom Rini <trini@ti.com> wrote:
> >
> > > Hello,
> > >
> > > This replaces my previous pull-request and is new warning free on
> > > MAKEALL -a arm for ELDK4.2/5.1/5.2.1.
> > >
> > > The following changes since commit
> > > 4d3c95f5ea7c737a21cd6b9c59435ee693b3f127:
> > >
> > > zfs: Add ZFS filesystem support (2012-08-09 23:42:20 +0200)
> > >
> > > are available in the git repository at:
> > >
> > > git://git.denx.de/u-boot-staging trini at ti.com
> > >
> > > for you to fetch changes up to
> > > 5d26e4de33fab7b132e8a8036ac54176f537d79f:
> > >
> > > ARM: add Raspberry Pi model B board, using BCM2835 SoC (2012-08-15
> > > 09:43:47 -0700)
> > >
> > > ----------------------------------------------------------------
> > > John Rigby (1):
> > > u8500: Separating mmc config parameters from driver
> > >
> > > Mathieu J. Poirier (10):
> > > snowball: Add support for ux500 based snowball board
> > > u8500: Moving prcmu to cpu directory
> > > snowball: Adding architecture dependent initialisation
> > > snowball: Adding CPU clock initialisation
> > > snowball: Moving to ux500.v2 addess scheme for PRCMU access
> > > snowball: applying power to LAN and GBF controllers
> > > u8500: Moving processor-specific functions to cpu area.
> > > u8500: Enabling power to MMC device on AB8500 V2
> > > armv7: Adding cpu specific cache managmenent
> > > snowball: Adding board specific cache cleanup routine
> > >
> > > Stephen Warren (4):
> > > README: fix references to config_cmd_default.h
> > > ARM: arm1176: enable instruction cache in arch_cpu_init()
> > > ARM: add basic support for the Broadcom BCM2835 SoC
> > > ARM: add Raspberry Pi model B board, using BCM2835 SoC
> > >
> > > MAINTAINERS | 8 +
> > > README | 4 +-
> > > arch/arm/cpu/arm1176/bcm2835/Makefile | 37 +
> > > arch/arm/cpu/arm1176/bcm2835/config.mk | 19 +
> > > arch/arm/cpu/arm1176/bcm2835/lowlevel_init.S | 19 +
> > > arch/arm/cpu/arm1176/bcm2835/reset.c | 35 +
> > > arch/arm/cpu/arm1176/bcm2835/timer.c | 55 ++
> > > arch/arm/cpu/arm1176/cpu.c | 7 +
> > > arch/arm/cpu/armv7/cpu.c | 8 +
> > > arch/arm/cpu/armv7/u8500/Makefile | 2 +-
> > > arch/arm/cpu/armv7/u8500/clock.c | 34 +
> > > arch/arm/cpu/armv7/u8500/cpu.c | 192 +++++
> > > .../arm/cpu/armv7}/u8500/prcmu.c | 128 +++-
> > > arch/arm/include/asm/arch-bcm2835/gpio.h | 66 ++
> > > arch/arm/include/asm/arch-bcm2835/timer.h | 37 +
> > > arch/arm/include/asm/arch-bcm2835/wdog.h | 36 +
> > > arch/arm/include/asm/arch-u8500/clock.h | 5 +-
> > > arch/arm/include/asm/arch-u8500/db8500_gpio.h | 42 ++
> > > arch/arm/include/asm/arch-u8500/db8500_pincfg.h | 170 +++++
> > > arch/arm/include/asm/arch-u8500/hardware.h | 33 +-
> > > .../arm/include/asm/arch-u8500/prcmu.h | 35 +-
> > > arch/arm/include/asm/arch-u8500/sys_proto.h | 1 +
> > > board/armltd/vexpress/ca9x4_ct_vxp.c | 21 +-
> > > board/raspberrypi/rpi_b/Makefile | 34 +
> > > board/raspberrypi/rpi_b/rpi_b.c | 34 +
> > > board/st-ericsson/snowball/Makefile | 49 ++
> > > board/st-ericsson/snowball/db8500_pins.h | 745
> > > ++++++++++++++++++++
> > > board/st-ericsson/snowball/snowball.c | 348 +++++++++
> > > board/st-ericsson/u8500/Makefile | 2 +-
> > > board/st-ericsson/u8500/u8500_href.c | 100 +--
> > > boards.cfg | 2 +
> > > drivers/gpio/Makefile | 2 +
> > > drivers/gpio/bcm2835_gpio.c | 89 +++
> > > drivers/gpio/db8500_gpio.c | 221 ++++++
> > > drivers/mmc/arm_pl180_mmci.c | 131 ++--
> > > drivers/mmc/arm_pl180_mmci.h | 27 +-
> > > drivers/serial/serial_pl01x.c | 2 +
> > > include/configs/rpi_b.h | 104 +++
> > > include/configs/snowball.h | 266 +++++++ 39
> > > files changed, 2937 insertions(+), 213 deletions(-) create mode
> > > 100644 arch/arm/cpu/arm1176/bcm2835/Makefile create mode 100644
> > > arch/arm/cpu/arm1176/bcm2835/config.mk create mode 100644
> > > arch/arm/cpu/arm1176/bcm2835/lowlevel_init.S create mode 100644
> > > arch/arm/cpu/arm1176/bcm2835/reset.c create mode 100644
> > > arch/arm/cpu/arm1176/bcm2835/timer.c create mode 100644
> > > arch/arm/cpu/armv7/u8500/cpu.c rename {board/st-ericsson =>
> > > arch/arm/cpu/armv7}/u8500/prcmu.c (58%) create mode 100644
> > > arch/arm/include/asm/arch-bcm2835/gpio.h create mode 100644
> > > arch/arm/include/asm/arch-bcm2835/timer.h create mode 100644
> > > arch/arm/include/asm/arch-bcm2835/wdog.h create mode 100644
> > > arch/arm/include/asm/arch-u8500/db8500_gpio.h create mode 100644
> > > arch/arm/include/asm/arch-u8500/db8500_pincfg.h rename
> > > board/st-ericsson/u8500/prcmu-fw.h =>
> > > arch/arm/include/asm/arch-u8500/prcmu.h (55%) create mode 100644
> > > board/raspberrypi/rpi_b/Makefile create mode 100644
> > > board/raspberrypi/rpi_b/rpi_b.c create mode 100644
> > > board/st-ericsson/snowball/Makefile create mode 100644
> > > board/st-ericsson/snowball/db8500_pins.h create mode 100644
> > > board/st-ericsson/snowball/snowball.c create mode 100644
> > > drivers/gpio/bcm2835_gpio.c create mode 100644
> > > drivers/gpio/db8500_gpio.c create mode 100644 include/configs/rpi_b.h
> > > create mode 100644 include/configs/snowball.h
> >
> > Are you sure you want me to only pull the top 15 patches of
> > u-boot-staging/trini at ti.com, but not the tens of ones that that are
> > below it in u-boot-staging/master? These are nowhere else, especially
> > not in u-boot/master, so I am wondering why your your request takes
> > staging/master as its base.
>
> I don't see any patches like that. And I did a quick re-confirm of what
> is in trini at ti.com and that's what I want to replace the commits in
> u-boot-arm/master from before.
To be clear, u-boot-staging/trini at ti.com is based on a somewhat older,
but not top of tree u-boot/master than what u-boot-arm is based on
today. I think your local u-boot/master is out of date.
http://git.denx.de/?p=u-boot.git;a=commit;h=4d3c95f5ea7c737a21cd6b9c59435ee693b3f127
is what my branch is on top of.
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20120818/10ab2dcd/attachment.pgp>
^ permalink raw reply [flat|nested] 18+ messages in thread* [U-Boot] Please pull u-boot-staging/trini@ti.com
2012-08-18 20:53 ` Tom Rini
@ 2012-08-30 7:44 ` Albert ARIBAUD
2012-08-30 15:50 ` Tom Rini
0 siblings, 1 reply; 18+ messages in thread
From: Albert ARIBAUD @ 2012-08-30 7:44 UTC (permalink / raw)
To: u-boot
Hi Tom,
On Sat, 18 Aug 2012 13:53:16 -0700, Tom Rini <trini@ti.com> wrote:
> On Sat, Aug 18, 2012 at 07:15:56AM -0700, Tom Rini wrote:
> > On Sat, Aug 18, 2012 at 08:28:55AM +0200, Albert ARIBAUD wrote:
> > > Hi Tom,
> > >
> > > On Fri, 17 Aug 2012 14:52:01 -0700, Tom Rini <trini@ti.com> wrote:
> > >
> > > > Hello,
> > > >
> > > > This replaces my previous pull-request and is new warning free
> > > > on MAKEALL -a arm for ELDK4.2/5.1/5.2.1.
> > > >
> > > > The following changes since commit
> > > > 4d3c95f5ea7c737a21cd6b9c59435ee693b3f127:
> > > >
> > > > zfs: Add ZFS filesystem support (2012-08-09 23:42:20 +0200)
> > > >
> > > > are available in the git repository at:
> > > >
> > > > git://git.denx.de/u-boot-staging trini at ti.com
> > > >
> > > > for you to fetch changes up to
> > > > 5d26e4de33fab7b132e8a8036ac54176f537d79f:
> > > >
> > > > ARM: add Raspberry Pi model B board, using BCM2835 SoC
> > > > (2012-08-15 09:43:47 -0700)
> > > >
> > > > ----------------------------------------------------------------
> > > > John Rigby (1):
> > > > u8500: Separating mmc config parameters from driver
> > > >
> > > > Mathieu J. Poirier (10):
> > > > snowball: Add support for ux500 based snowball board
> > > > u8500: Moving prcmu to cpu directory
> > > > snowball: Adding architecture dependent initialisation
> > > > snowball: Adding CPU clock initialisation
> > > > snowball: Moving to ux500.v2 addess scheme for PRCMU
> > > > access snowball: applying power to LAN and GBF controllers
> > > > u8500: Moving processor-specific functions to cpu area.
> > > > u8500: Enabling power to MMC device on AB8500 V2
> > > > armv7: Adding cpu specific cache managmenent
> > > > snowball: Adding board specific cache cleanup routine
> > > >
> > > > Stephen Warren (4):
> > > > README: fix references to config_cmd_default.h
> > > > ARM: arm1176: enable instruction cache in arch_cpu_init()
> > > > ARM: add basic support for the Broadcom BCM2835 SoC
> > > > ARM: add Raspberry Pi model B board, using BCM2835 SoC
> > > >
> > > > MAINTAINERS | 8 +
> > > > README | 4 +-
> > > > arch/arm/cpu/arm1176/bcm2835/Makefile | 37 +
> > > > arch/arm/cpu/arm1176/bcm2835/config.mk | 19 +
> > > > arch/arm/cpu/arm1176/bcm2835/lowlevel_init.S | 19 +
> > > > arch/arm/cpu/arm1176/bcm2835/reset.c | 35 +
> > > > arch/arm/cpu/arm1176/bcm2835/timer.c | 55 ++
> > > > arch/arm/cpu/arm1176/cpu.c | 7 +
> > > > arch/arm/cpu/armv7/cpu.c | 8 +
> > > > arch/arm/cpu/armv7/u8500/Makefile | 2 +-
> > > > arch/arm/cpu/armv7/u8500/clock.c | 34 +
> > > > arch/arm/cpu/armv7/u8500/cpu.c | 192 +++++
> > > > .../arm/cpu/armv7}/u8500/prcmu.c | 128 +++-
> > > > arch/arm/include/asm/arch-bcm2835/gpio.h | 66 ++
> > > > arch/arm/include/asm/arch-bcm2835/timer.h | 37 +
> > > > arch/arm/include/asm/arch-bcm2835/wdog.h | 36 +
> > > > arch/arm/include/asm/arch-u8500/clock.h | 5 +-
> > > > arch/arm/include/asm/arch-u8500/db8500_gpio.h | 42 ++
> > > > arch/arm/include/asm/arch-u8500/db8500_pincfg.h | 170 +++++
> > > > arch/arm/include/asm/arch-u8500/hardware.h | 33 +-
> > > > .../arm/include/asm/arch-u8500/prcmu.h | 35 +-
> > > > arch/arm/include/asm/arch-u8500/sys_proto.h | 1 +
> > > > board/armltd/vexpress/ca9x4_ct_vxp.c | 21 +-
> > > > board/raspberrypi/rpi_b/Makefile | 34 +
> > > > board/raspberrypi/rpi_b/rpi_b.c | 34 +
> > > > board/st-ericsson/snowball/Makefile | 49 ++
> > > > board/st-ericsson/snowball/db8500_pins.h | 745
> > > > ++++++++++++++++++++
> > > > board/st-ericsson/snowball/snowball.c | 348
> > > > +++++++++ board/st-ericsson/u8500/Makefile
> > > > | 2 +- board/st-ericsson/u8500/u8500_href.c |
> > > > 100 +-- boards.cfg |
> > > > 2 + drivers/gpio/Makefile | 2 +
> > > > drivers/gpio/bcm2835_gpio.c | 89 +++
> > > > drivers/gpio/db8500_gpio.c | 221 ++++++
> > > > drivers/mmc/arm_pl180_mmci.c | 131 ++--
> > > > drivers/mmc/arm_pl180_mmci.h | 27 +-
> > > > drivers/serial/serial_pl01x.c | 2 +
> > > > include/configs/rpi_b.h | 104 +++
> > > > include/configs/snowball.h | 266
> > > > +++++++ 39 files changed, 2937 insertions(+), 213 deletions(-)
> > > > create mode 100644 arch/arm/cpu/arm1176/bcm2835/Makefile create
> > > > mode 100644 arch/arm/cpu/arm1176/bcm2835/config.mk create mode
> > > > 100644 arch/arm/cpu/arm1176/bcm2835/lowlevel_init.S create mode
> > > > 100644 arch/arm/cpu/arm1176/bcm2835/reset.c create mode 100644
> > > > arch/arm/cpu/arm1176/bcm2835/timer.c create mode 100644
> > > > arch/arm/cpu/armv7/u8500/cpu.c rename {board/st-ericsson =>
> > > > arch/arm/cpu/armv7}/u8500/prcmu.c (58%) create mode 100644
> > > > arch/arm/include/asm/arch-bcm2835/gpio.h create mode 100644
> > > > arch/arm/include/asm/arch-bcm2835/timer.h create mode 100644
> > > > arch/arm/include/asm/arch-bcm2835/wdog.h create mode 100644
> > > > arch/arm/include/asm/arch-u8500/db8500_gpio.h create mode 100644
> > > > arch/arm/include/asm/arch-u8500/db8500_pincfg.h rename
> > > > board/st-ericsson/u8500/prcmu-fw.h =>
> > > > arch/arm/include/asm/arch-u8500/prcmu.h (55%) create mode 100644
> > > > board/raspberrypi/rpi_b/Makefile create mode 100644
> > > > board/raspberrypi/rpi_b/rpi_b.c create mode 100644
> > > > board/st-ericsson/snowball/Makefile create mode 100644
> > > > board/st-ericsson/snowball/db8500_pins.h create mode 100644
> > > > board/st-ericsson/snowball/snowball.c create mode 100644
> > > > drivers/gpio/bcm2835_gpio.c create mode 100644
> > > > drivers/gpio/db8500_gpio.c create mode 100644
> > > > include/configs/rpi_b.h create mode 100644
> > > > include/configs/snowball.h
> > >
> > > Are you sure you want me to only pull the top 15 patches of
> > > u-boot-staging/trini at ti.com, but not the tens of ones that that
> > > are below it in u-boot-staging/master? These are nowhere else,
> > > especially not in u-boot/master, so I am wondering why your your
> > > request takes staging/master as its base.
> >
> > I don't see any patches like that. And I did a quick re-confirm of
> > what is in trini at ti.com and that's what I want to replace the
> > commits in u-boot-arm/master from before.
>
> To be clear, u-boot-staging/trini at ti.com is based on a somewhat older,
> but not top of tree u-boot/master than what u-boot-arm is based on
> today. I think your local u-boot/master is out of date.
> http://git.denx.de/?p=u-boot.git;a=commit;h=4d3c95f5ea7c737a21cd6b9c59435ee693b3f127
> is what my branch is on top of.
Top 15 patches ("snowball: Add support for ux500 based snowball
board" to "ARM: add Raspberry Pi model B board, using BCM2835 SoC")
applied to u-boot-arm/master, resulting in the total number of boards
built rising up from 314 to 315.
Please make sure this is what you wanted.
Thanks and apologies for the time it took!
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 18+ messages in thread* [U-Boot] Please pull u-boot-staging/trini@ti.com
2012-08-30 7:44 ` Albert ARIBAUD
@ 2012-08-30 15:50 ` Tom Rini
0 siblings, 0 replies; 18+ messages in thread
From: Tom Rini @ 2012-08-30 15:50 UTC (permalink / raw)
To: u-boot
On Thu, Aug 30, 2012 at 09:44:54AM +0200, Albert ARIBAUD wrote:
> Hi Tom,
>
> On Sat, 18 Aug 2012 13:53:16 -0700, Tom Rini <trini@ti.com> wrote:
>
> > On Sat, Aug 18, 2012 at 07:15:56AM -0700, Tom Rini wrote:
> > > On Sat, Aug 18, 2012 at 08:28:55AM +0200, Albert ARIBAUD wrote:
> > > > Hi Tom,
> > > >
> > > > On Fri, 17 Aug 2012 14:52:01 -0700, Tom Rini <trini@ti.com> wrote:
> > > >
> > > > > Hello,
> > > > >
> > > > > This replaces my previous pull-request and is new warning free
> > > > > on MAKEALL -a arm for ELDK4.2/5.1/5.2.1.
> > > > >
> > > > > The following changes since commit
> > > > > 4d3c95f5ea7c737a21cd6b9c59435ee693b3f127:
> > > > >
> > > > > zfs: Add ZFS filesystem support (2012-08-09 23:42:20 +0200)
> > > > >
> > > > > are available in the git repository at:
> > > > >
> > > > > git://git.denx.de/u-boot-staging trini at ti.com
> > > > >
> > > > > for you to fetch changes up to
> > > > > 5d26e4de33fab7b132e8a8036ac54176f537d79f:
> > > > >
> > > > > ARM: add Raspberry Pi model B board, using BCM2835 SoC
> > > > > (2012-08-15 09:43:47 -0700)
> > > > >
> > > > > ----------------------------------------------------------------
> > > > > John Rigby (1):
> > > > > u8500: Separating mmc config parameters from driver
> > > > >
> > > > > Mathieu J. Poirier (10):
> > > > > snowball: Add support for ux500 based snowball board
> > > > > u8500: Moving prcmu to cpu directory
> > > > > snowball: Adding architecture dependent initialisation
> > > > > snowball: Adding CPU clock initialisation
> > > > > snowball: Moving to ux500.v2 addess scheme for PRCMU
> > > > > access snowball: applying power to LAN and GBF controllers
> > > > > u8500: Moving processor-specific functions to cpu area.
> > > > > u8500: Enabling power to MMC device on AB8500 V2
> > > > > armv7: Adding cpu specific cache managmenent
> > > > > snowball: Adding board specific cache cleanup routine
> > > > >
> > > > > Stephen Warren (4):
> > > > > README: fix references to config_cmd_default.h
> > > > > ARM: arm1176: enable instruction cache in arch_cpu_init()
> > > > > ARM: add basic support for the Broadcom BCM2835 SoC
> > > > > ARM: add Raspberry Pi model B board, using BCM2835 SoC
> > > > >
> > > > > MAINTAINERS | 8 +
> > > > > README | 4 +-
> > > > > arch/arm/cpu/arm1176/bcm2835/Makefile | 37 +
> > > > > arch/arm/cpu/arm1176/bcm2835/config.mk | 19 +
> > > > > arch/arm/cpu/arm1176/bcm2835/lowlevel_init.S | 19 +
> > > > > arch/arm/cpu/arm1176/bcm2835/reset.c | 35 +
> > > > > arch/arm/cpu/arm1176/bcm2835/timer.c | 55 ++
> > > > > arch/arm/cpu/arm1176/cpu.c | 7 +
> > > > > arch/arm/cpu/armv7/cpu.c | 8 +
> > > > > arch/arm/cpu/armv7/u8500/Makefile | 2 +-
> > > > > arch/arm/cpu/armv7/u8500/clock.c | 34 +
> > > > > arch/arm/cpu/armv7/u8500/cpu.c | 192 +++++
> > > > > .../arm/cpu/armv7}/u8500/prcmu.c | 128 +++-
> > > > > arch/arm/include/asm/arch-bcm2835/gpio.h | 66 ++
> > > > > arch/arm/include/asm/arch-bcm2835/timer.h | 37 +
> > > > > arch/arm/include/asm/arch-bcm2835/wdog.h | 36 +
> > > > > arch/arm/include/asm/arch-u8500/clock.h | 5 +-
> > > > > arch/arm/include/asm/arch-u8500/db8500_gpio.h | 42 ++
> > > > > arch/arm/include/asm/arch-u8500/db8500_pincfg.h | 170 +++++
> > > > > arch/arm/include/asm/arch-u8500/hardware.h | 33 +-
> > > > > .../arm/include/asm/arch-u8500/prcmu.h | 35 +-
> > > > > arch/arm/include/asm/arch-u8500/sys_proto.h | 1 +
> > > > > board/armltd/vexpress/ca9x4_ct_vxp.c | 21 +-
> > > > > board/raspberrypi/rpi_b/Makefile | 34 +
> > > > > board/raspberrypi/rpi_b/rpi_b.c | 34 +
> > > > > board/st-ericsson/snowball/Makefile | 49 ++
> > > > > board/st-ericsson/snowball/db8500_pins.h | 745
> > > > > ++++++++++++++++++++
> > > > > board/st-ericsson/snowball/snowball.c | 348
> > > > > +++++++++ board/st-ericsson/u8500/Makefile
> > > > > | 2 +- board/st-ericsson/u8500/u8500_href.c |
> > > > > 100 +-- boards.cfg |
> > > > > 2 + drivers/gpio/Makefile | 2 +
> > > > > drivers/gpio/bcm2835_gpio.c | 89 +++
> > > > > drivers/gpio/db8500_gpio.c | 221 ++++++
> > > > > drivers/mmc/arm_pl180_mmci.c | 131 ++--
> > > > > drivers/mmc/arm_pl180_mmci.h | 27 +-
> > > > > drivers/serial/serial_pl01x.c | 2 +
> > > > > include/configs/rpi_b.h | 104 +++
> > > > > include/configs/snowball.h | 266
> > > > > +++++++ 39 files changed, 2937 insertions(+), 213 deletions(-)
> > > > > create mode 100644 arch/arm/cpu/arm1176/bcm2835/Makefile create
> > > > > mode 100644 arch/arm/cpu/arm1176/bcm2835/config.mk create mode
> > > > > 100644 arch/arm/cpu/arm1176/bcm2835/lowlevel_init.S create mode
> > > > > 100644 arch/arm/cpu/arm1176/bcm2835/reset.c create mode 100644
> > > > > arch/arm/cpu/arm1176/bcm2835/timer.c create mode 100644
> > > > > arch/arm/cpu/armv7/u8500/cpu.c rename {board/st-ericsson =>
> > > > > arch/arm/cpu/armv7}/u8500/prcmu.c (58%) create mode 100644
> > > > > arch/arm/include/asm/arch-bcm2835/gpio.h create mode 100644
> > > > > arch/arm/include/asm/arch-bcm2835/timer.h create mode 100644
> > > > > arch/arm/include/asm/arch-bcm2835/wdog.h create mode 100644
> > > > > arch/arm/include/asm/arch-u8500/db8500_gpio.h create mode 100644
> > > > > arch/arm/include/asm/arch-u8500/db8500_pincfg.h rename
> > > > > board/st-ericsson/u8500/prcmu-fw.h =>
> > > > > arch/arm/include/asm/arch-u8500/prcmu.h (55%) create mode 100644
> > > > > board/raspberrypi/rpi_b/Makefile create mode 100644
> > > > > board/raspberrypi/rpi_b/rpi_b.c create mode 100644
> > > > > board/st-ericsson/snowball/Makefile create mode 100644
> > > > > board/st-ericsson/snowball/db8500_pins.h create mode 100644
> > > > > board/st-ericsson/snowball/snowball.c create mode 100644
> > > > > drivers/gpio/bcm2835_gpio.c create mode 100644
> > > > > drivers/gpio/db8500_gpio.c create mode 100644
> > > > > include/configs/rpi_b.h create mode 100644
> > > > > include/configs/snowball.h
> > > >
> > > > Are you sure you want me to only pull the top 15 patches of
> > > > u-boot-staging/trini at ti.com, but not the tens of ones that that
> > > > are below it in u-boot-staging/master? These are nowhere else,
> > > > especially not in u-boot/master, so I am wondering why your your
> > > > request takes staging/master as its base.
> > >
> > > I don't see any patches like that. And I did a quick re-confirm of
> > > what is in trini at ti.com and that's what I want to replace the
> > > commits in u-boot-arm/master from before.
> >
> > To be clear, u-boot-staging/trini at ti.com is based on a somewhat older,
> > but not top of tree u-boot/master than what u-boot-arm is based on
> > today. I think your local u-boot/master is out of date.
> > http://git.denx.de/?p=u-boot.git;a=commit;h=4d3c95f5ea7c737a21cd6b9c59435ee693b3f127
> > is what my branch is on top of.
>
> Top 15 patches ("snowball: Add support for ux500 based snowball
> board" to "ARM: add Raspberry Pi model B board, using BCM2835 SoC")
> applied to u-boot-arm/master, resulting in the total number of boards
> built rising up from 314 to 315.
>
> Please make sure this is what you wanted.
>
> Thanks and apologies for the time it took!
Thanks for taking it. Things look good. You only saw one new board
built because the patch from Allen Martin that makes 'MAKEALL arm' work
like 'MAKEALL -a arm' isn't in yet :) (rpi_b is arm1176 which isn't in
MAKEALL arm but is I believe in -a arm).
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20120830/c92aa84c/attachment.pgp>
^ permalink raw reply [flat|nested] 18+ messages in thread
* [U-Boot] Please pull u-boot-staging/trini@ti.com
@ 2012-02-14 18:17 Tom Rini
2012-02-17 22:53 ` Wolfgang Denk
0 siblings, 1 reply; 18+ messages in thread
From: Tom Rini @ 2012-02-14 18:17 UTC (permalink / raw)
To: u-boot
The following changes since commit 9a3aae22edf1eda6326cc51c28631ca5c23b7706:
Christian Riesch (1):
arm, davinci: Add support for the Calimain board from OMICRON electronics
are available in the git repository at:
git://git.denx.de/u-boot-staging trini at ti.com
Peter Meerwald (3):
doc: complete, typos
cmd_eeprom: typo
usb_ether: fix typo
common/cmd_eeprom.c | 2 +-
doc/README.commands | 12 ++++++------
drivers/usb/eth/usb_ether.c | 2 +-
3 files changed, 8 insertions(+), 8 deletions(-)
I'm busily kicking git for a 'git push write trini at ti.com:trini at ti.com' says 'Everything up-to-date' but request-pull, the web interface, etc, says it can't find things. The patches are also at http://patchwork.ozlabs.org/bundle/trini/14feb2012-imports-staging/
--
Tom
^ permalink raw reply [flat|nested] 18+ messages in thread* [U-Boot] Please pull u-boot-staging/trini@ti.com
2012-02-14 18:17 Tom Rini
@ 2012-02-17 22:53 ` Wolfgang Denk
0 siblings, 0 replies; 18+ messages in thread
From: Wolfgang Denk @ 2012-02-17 22:53 UTC (permalink / raw)
To: u-boot
Dear Tom Rini,
In message <C71DFD18-8F51-4CA2-AF1C-5008C817BA57@gmail.com> you wrote:
> The following changes since commit =
> 9a3aae22edf1eda6326cc51c28631ca5c23b7706:
> Christian Riesch (1):
> arm, davinci: Add support for the Calimain board from OMICRON =
> electronics
>
> are available in the git repository at:
>
> git://git.denx.de/u-boot-staging trini at ti.com
>
> Peter Meerwald (3):
> doc: complete, typos
> cmd_eeprom: typo
> usb_ether: fix typo
>
> common/cmd_eeprom.c | 2 +-
> doc/README.commands | 12 ++++++------
> drivers/usb/eth/usb_ether.c | 2 +-
> 3 files changed, 8 insertions(+), 8 deletions(-)
Applied, thanks.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Landing: a controlled mid-air collision with a planet.
^ permalink raw reply [flat|nested] 18+ messages in thread
end of thread, other threads:[~2012-09-04 19:09 UTC | newest]
Thread overview: 18+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2012-08-10 16:10 [U-Boot] Please pull u-boot-staging/trini@ti.com Tom Rini
2012-08-10 20:06 ` Wolfgang Denk
2012-08-14 0:04 ` Albert ARIBAUD
2012-08-14 1:06 ` Albert ARIBAUD
2012-08-14 12:58 ` Mathieu Poirier
2012-08-15 16:51 ` Tom Rini
-- strict thread matches above, loose matches on Subject: below --
2012-09-04 16:08 Tom Rini
2012-09-04 19:09 ` Albert ARIBAUD
2012-08-31 23:27 Tom Rini
2012-09-01 7:39 ` Albert ARIBAUD
2012-08-17 21:52 Tom Rini
2012-08-18 6:28 ` Albert ARIBAUD
2012-08-18 14:15 ` Tom Rini
2012-08-18 20:53 ` Tom Rini
2012-08-30 7:44 ` Albert ARIBAUD
2012-08-30 15:50 ` Tom Rini
2012-02-14 18:17 Tom Rini
2012-02-17 22:53 ` Wolfgang Denk
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.