* [PATCH 3/4] ARM: nomadik: convert all clocks except timer to dt
@ 2013-04-20 14:09 Linus Walleij
2013-04-22 22:01 ` Mike Turquette
0 siblings, 1 reply; 3+ messages in thread
From: Linus Walleij @ 2013-04-20 14:09 UTC (permalink / raw)
To: linux-arm-kernel
This moves all Nomadik clocks except the one used for the
timer/clocksource over to the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
.../devicetree/bindings/arm/ste-nomadik.txt | 5 ++
arch/arm/boot/dts/ste-nomadik-stn8815.dtsi | 54 ++++++++++++++++++++++
arch/arm/mach-nomadik/cpu-8815.c | 20 +-------
drivers/clk/clk-nomadik.c | 26 +++--------
4 files changed, 68 insertions(+), 37 deletions(-)
diff --git a/Documentation/devicetree/bindings/arm/ste-nomadik.txt b/Documentation/devicetree/bindings/arm/ste-nomadik.txt
index 19bca04..6256ec3 100644
--- a/Documentation/devicetree/bindings/arm/ste-nomadik.txt
+++ b/Documentation/devicetree/bindings/arm/ste-nomadik.txt
@@ -3,6 +3,11 @@ ST-Ericsson Nomadik Device Tree Bindings
For various board the "board" node may contain specific properties
that pertain to this particular board, such as board-specific GPIOs.
+Required root node property: src
+- Nomadik System and reset controller used for basic chip control, clock
+ and reset line control.
+- compatible: must be "stericsson,nomadik,src"
+
Boards with the Nomadik SoC include:
S8815 "MiniKit" manufactured by Calao Systems:
diff --git a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
index 4a4aab3..f0df948 100644
--- a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
+++ b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
@@ -45,6 +45,7 @@
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <0>;
+ clocks = <&pclk>;
};
gpio1: gpio at 101e5000 {
@@ -57,6 +58,7 @@
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <1>;
+ clocks = <&pclk>;
};
gpio2: gpio at 101e6000 {
@@ -69,6 +71,7 @@
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <2>;
+ clocks = <&pclk>;
};
gpio3: gpio at 101e7000 {
@@ -81,12 +84,50 @@
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <3>;
+ clocks = <&pclk>;
};
pinctrl {
compatible = "stericsson,nmk-pinctrl-stn8815";
};
+ src: src at 101e0000 {
+ compatible = "stericsson,nomadik-src";
+ reg = <0x101e0000 0x1000>;
+ clocks {
+ /*
+ * Dummy clock for primecells
+ */
+ pclk: pclk at 0 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <2400000>;
+ };
+ /*
+ * The 2.4 MHz TIMCLK reference clock is active at
+ * boot time, this is actually the MXTALCLK @19.2 MHz
+ * divided by 8. This clock is used by the timers and
+ * watchdog. See page 105 ff.
+ */
+ timclk: timclk at 2.4M {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <2400000>;
+ };
+ /*
+ * At boot time, PLL2 is set to generate a set of
+ * fixed clocks, one of them is CLK48, the 48 MHz
+ * clock, routed to the UART, MMC/SD, I2C, IrDA,
+ * USB and SSP blocks.
+ */
+ clk48: clk48 at 48M {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <48000000>;
+ };
+ };
+ };
+
/* A NAND flash of 128 MiB */
fsmc: flash at 40000000 {
compatible = "stericsson,fsmc-nand";
@@ -97,6 +138,7 @@
<0x41000000 0x2000>, /* NAND Base ADDR */
<0x40800000 0x2000>; /* NAND Base CMD */
reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd";
+ clocks = <&pclk>;
status = "okay";
partition at 0 {
@@ -211,6 +253,8 @@
reg = <0x101fd000 0x1000>;
interrupt-parent = <&vica>;
interrupts = <12>;
+ clocks = <&clk48>, <&pclk>;
+ clock-names = "uartclk", "apb_pclk";
};
uart1: uart at 101fb000 {
@@ -218,6 +262,8 @@
reg = <0x101fb000 0x1000>;
interrupt-parent = <&vica>;
interrupts = <17>;
+ clocks = <&clk48>, <&pclk>;
+ clock-names = "uartclk", "apb_pclk";
};
uart2: uart at 101f2000 {
@@ -225,17 +271,23 @@
reg = <0x101f2000 0x1000>;
interrupt-parent = <&vica>;
interrupts = <28>;
+ clocks = <&clk48>, <&pclk>;
+ clock-names = "uartclk", "apb_pclk";
status = "disabled";
};
rng: rng at 101b0000 {
compatible = "arm,primecell";
reg = <0x101b0000 0x1000>;
+ clocks = <&clk48>, <&pclk>;
+ clock-names = "rng", "apb_pclk";
};
rtc: rtc at 101e8000 {
compatible = "arm,pl031", "arm,primecell";
reg = <0x101e8000 0x1000>;
+ clocks = <&pclk>;
+ clock-names = "apb_pclk";
interrupt-parent = <&vica>;
interrupts = <10>;
};
@@ -243,6 +295,8 @@
mmcsd: sdi at 101f6000 {
compatible = "arm,pl18x", "arm,primecell";
reg = <0x101f6000 0x1000>;
+ clocks = <&clk48>, <&pclk>;
+ clock-names = "mclk", "apb_pclk";
interrupt-parent = <&vica>;
interrupts = <22>;
max-frequency = <48000000>;
diff --git a/arch/arm/mach-nomadik/cpu-8815.c b/arch/arm/mach-nomadik/cpu-8815.c
index 59f6ff5..0e2c5e0 100644
--- a/arch/arm/mach-nomadik/cpu-8815.c
+++ b/arch/arm/mach-nomadik/cpu-8815.c
@@ -280,28 +280,12 @@ device_initcall(cpu8815_mmcsd_init);
/* These are mostly to get the right device names for the clock lookups */
static struct of_dev_auxdata cpu8815_auxdata_lookup[] __initdata = {
- OF_DEV_AUXDATA("st,nomadik-gpio", NOMADIK_GPIO0_BASE,
- "gpio.0", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", NOMADIK_GPIO1_BASE,
- "gpio.1", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", NOMADIK_GPIO2_BASE,
- "gpio.2", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", NOMADIK_GPIO3_BASE,
- "gpio.3", NULL),
OF_DEV_AUXDATA("stericsson,nmk-pinctrl-stn8815", 0,
"pinctrl-stn8815", NULL),
- OF_DEV_AUXDATA("arm,primecell", NOMADIK_UART0_BASE,
- "uart0", NULL),
- OF_DEV_AUXDATA("arm,primecell", NOMADIK_UART1_BASE,
- "uart1", NULL),
- OF_DEV_AUXDATA("arm,primecell", NOMADIK_RNG_BASE,
- "rng", NULL),
- OF_DEV_AUXDATA("arm,primecell", NOMADIK_RTC_BASE,
- "rtc-pl031", NULL),
OF_DEV_AUXDATA("stericsson,fsmc-nand", NOMADIK_FSMC_BASE,
- "fsmc-nand", &cpu8815_nand_data),
+ NULL, &cpu8815_nand_data),
OF_DEV_AUXDATA("arm,primecell", NOMADIK_SDI_BASE,
- "mmci", &mmcsd_plat_data),
+ NULL, &mmcsd_plat_data),
{ /* sentinel */ },
};
diff --git a/drivers/clk/clk-nomadik.c b/drivers/clk/clk-nomadik.c
index 6b4c70f..19f197c 100644
--- a/drivers/clk/clk-nomadik.c
+++ b/drivers/clk/clk-nomadik.c
@@ -3,24 +3,24 @@
#include <linux/err.h>
#include <linux/io.h>
#include <linux/clk-provider.h>
+#include <linux/of.h>
/*
* The Nomadik clock tree is described in the STN8815A12 DB V4.2
* reference manual for the chip, page 94 ff.
*/
+static const __initconst struct of_device_id cpu8815_clk_match[] = {
+ { .compatible = "fixed-clock", .data = of_fixed_clk_setup, },
+ { /* sentinel */ }
+};
+
void __init nomadik_clk_init(void)
{
struct clk *clk;
clk = clk_register_fixed_rate(NULL, "apb_pclk", NULL, CLK_IS_ROOT, 0);
clk_register_clkdev(clk, "apb_pclk", NULL);
- clk_register_clkdev(clk, NULL, "gpio.0");
- clk_register_clkdev(clk, NULL, "gpio.1");
- clk_register_clkdev(clk, NULL, "gpio.2");
- clk_register_clkdev(clk, NULL, "gpio.3");
- clk_register_clkdev(clk, NULL, "rng");
- clk_register_clkdev(clk, NULL, "fsmc-nand");
/*
* The 2.4 MHz TIMCLK reference clock is active at boot time, this is
@@ -32,17 +32,5 @@ void __init nomadik_clk_init(void)
clk_register_clkdev(clk, NULL, "mtu0");
clk_register_clkdev(clk, NULL, "mtu1");
- /*
- * At boot time, PLL2 is set to generate a set of fixed clocks,
- * one of them is CLK48, the 48 MHz clock, routed to the UART, MMC/SD
- * I2C, IrDA, USB and SSP blocks.
- */
- clk = clk_register_fixed_rate(NULL, "CLK48", NULL, CLK_IS_ROOT,
- 48000000);
- clk_register_clkdev(clk, NULL, "uart0");
- clk_register_clkdev(clk, NULL, "uart1");
- clk_register_clkdev(clk, NULL, "mmci");
- clk_register_clkdev(clk, NULL, "ssp");
- clk_register_clkdev(clk, NULL, "nmk-i2c.0");
- clk_register_clkdev(clk, NULL, "nmk-i2c.1");
+ of_clk_init(cpu8815_clk_match);
}
--
1.8.1.4
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [PATCH 3/4] ARM: nomadik: convert all clocks except timer to dt
2013-04-20 14:09 [PATCH 3/4] ARM: nomadik: convert all clocks except timer to dt Linus Walleij
@ 2013-04-22 22:01 ` Mike Turquette
0 siblings, 0 replies; 3+ messages in thread
From: Mike Turquette @ 2013-04-22 22:01 UTC (permalink / raw)
To: linux-arm-kernel
Quoting Linus Walleij (2013-04-20 07:09:34)
> This moves all Nomadik clocks except the one used for the
> timer/clocksource over to the device tree.
>
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For the clk-nomadik.c part:
Acked-by: Mike Turquette <mturquette@linaro.org>
> ---
> .../devicetree/bindings/arm/ste-nomadik.txt | 5 ++
> arch/arm/boot/dts/ste-nomadik-stn8815.dtsi | 54 ++++++++++++++++++++++
> arch/arm/mach-nomadik/cpu-8815.c | 20 +-------
> drivers/clk/clk-nomadik.c | 26 +++--------
> 4 files changed, 68 insertions(+), 37 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/arm/ste-nomadik.txt b/Documentation/devicetree/bindings/arm/ste-nomadik.txt
> index 19bca04..6256ec3 100644
> --- a/Documentation/devicetree/bindings/arm/ste-nomadik.txt
> +++ b/Documentation/devicetree/bindings/arm/ste-nomadik.txt
> @@ -3,6 +3,11 @@ ST-Ericsson Nomadik Device Tree Bindings
> For various board the "board" node may contain specific properties
> that pertain to this particular board, such as board-specific GPIOs.
>
> +Required root node property: src
> +- Nomadik System and reset controller used for basic chip control, clock
> + and reset line control.
> +- compatible: must be "stericsson,nomadik,src"
> +
> Boards with the Nomadik SoC include:
>
> S8815 "MiniKit" manufactured by Calao Systems:
> diff --git a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
> index 4a4aab3..f0df948 100644
> --- a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
> +++ b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
> @@ -45,6 +45,7 @@
> gpio-controller;
> #gpio-cells = <2>;
> gpio-bank = <0>;
> + clocks = <&pclk>;
> };
>
> gpio1: gpio at 101e5000 {
> @@ -57,6 +58,7 @@
> gpio-controller;
> #gpio-cells = <2>;
> gpio-bank = <1>;
> + clocks = <&pclk>;
> };
>
> gpio2: gpio at 101e6000 {
> @@ -69,6 +71,7 @@
> gpio-controller;
> #gpio-cells = <2>;
> gpio-bank = <2>;
> + clocks = <&pclk>;
> };
>
> gpio3: gpio at 101e7000 {
> @@ -81,12 +84,50 @@
> gpio-controller;
> #gpio-cells = <2>;
> gpio-bank = <3>;
> + clocks = <&pclk>;
> };
>
> pinctrl {
> compatible = "stericsson,nmk-pinctrl-stn8815";
> };
>
> + src: src at 101e0000 {
> + compatible = "stericsson,nomadik-src";
> + reg = <0x101e0000 0x1000>;
> + clocks {
> + /*
> + * Dummy clock for primecells
> + */
> + pclk: pclk at 0 {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <2400000>;
> + };
> + /*
> + * The 2.4 MHz TIMCLK reference clock is active at
> + * boot time, this is actually the MXTALCLK @19.2 MHz
> + * divided by 8. This clock is used by the timers and
> + * watchdog. See page 105 ff.
> + */
> + timclk: timclk at 2.4M {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <2400000>;
> + };
> + /*
> + * At boot time, PLL2 is set to generate a set of
> + * fixed clocks, one of them is CLK48, the 48 MHz
> + * clock, routed to the UART, MMC/SD, I2C, IrDA,
> + * USB and SSP blocks.
> + */
> + clk48: clk48 at 48M {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <48000000>;
> + };
> + };
> + };
> +
> /* A NAND flash of 128 MiB */
> fsmc: flash at 40000000 {
> compatible = "stericsson,fsmc-nand";
> @@ -97,6 +138,7 @@
> <0x41000000 0x2000>, /* NAND Base ADDR */
> <0x40800000 0x2000>; /* NAND Base CMD */
> reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd";
> + clocks = <&pclk>;
> status = "okay";
>
> partition at 0 {
> @@ -211,6 +253,8 @@
> reg = <0x101fd000 0x1000>;
> interrupt-parent = <&vica>;
> interrupts = <12>;
> + clocks = <&clk48>, <&pclk>;
> + clock-names = "uartclk", "apb_pclk";
> };
>
> uart1: uart at 101fb000 {
> @@ -218,6 +262,8 @@
> reg = <0x101fb000 0x1000>;
> interrupt-parent = <&vica>;
> interrupts = <17>;
> + clocks = <&clk48>, <&pclk>;
> + clock-names = "uartclk", "apb_pclk";
> };
>
> uart2: uart at 101f2000 {
> @@ -225,17 +271,23 @@
> reg = <0x101f2000 0x1000>;
> interrupt-parent = <&vica>;
> interrupts = <28>;
> + clocks = <&clk48>, <&pclk>;
> + clock-names = "uartclk", "apb_pclk";
> status = "disabled";
> };
>
> rng: rng at 101b0000 {
> compatible = "arm,primecell";
> reg = <0x101b0000 0x1000>;
> + clocks = <&clk48>, <&pclk>;
> + clock-names = "rng", "apb_pclk";
> };
>
> rtc: rtc at 101e8000 {
> compatible = "arm,pl031", "arm,primecell";
> reg = <0x101e8000 0x1000>;
> + clocks = <&pclk>;
> + clock-names = "apb_pclk";
> interrupt-parent = <&vica>;
> interrupts = <10>;
> };
> @@ -243,6 +295,8 @@
> mmcsd: sdi at 101f6000 {
> compatible = "arm,pl18x", "arm,primecell";
> reg = <0x101f6000 0x1000>;
> + clocks = <&clk48>, <&pclk>;
> + clock-names = "mclk", "apb_pclk";
> interrupt-parent = <&vica>;
> interrupts = <22>;
> max-frequency = <48000000>;
> diff --git a/arch/arm/mach-nomadik/cpu-8815.c b/arch/arm/mach-nomadik/cpu-8815.c
> index 59f6ff5..0e2c5e0 100644
> --- a/arch/arm/mach-nomadik/cpu-8815.c
> +++ b/arch/arm/mach-nomadik/cpu-8815.c
> @@ -280,28 +280,12 @@ device_initcall(cpu8815_mmcsd_init);
>
> /* These are mostly to get the right device names for the clock lookups */
> static struct of_dev_auxdata cpu8815_auxdata_lookup[] __initdata = {
> - OF_DEV_AUXDATA("st,nomadik-gpio", NOMADIK_GPIO0_BASE,
> - "gpio.0", NULL),
> - OF_DEV_AUXDATA("st,nomadik-gpio", NOMADIK_GPIO1_BASE,
> - "gpio.1", NULL),
> - OF_DEV_AUXDATA("st,nomadik-gpio", NOMADIK_GPIO2_BASE,
> - "gpio.2", NULL),
> - OF_DEV_AUXDATA("st,nomadik-gpio", NOMADIK_GPIO3_BASE,
> - "gpio.3", NULL),
> OF_DEV_AUXDATA("stericsson,nmk-pinctrl-stn8815", 0,
> "pinctrl-stn8815", NULL),
> - OF_DEV_AUXDATA("arm,primecell", NOMADIK_UART0_BASE,
> - "uart0", NULL),
> - OF_DEV_AUXDATA("arm,primecell", NOMADIK_UART1_BASE,
> - "uart1", NULL),
> - OF_DEV_AUXDATA("arm,primecell", NOMADIK_RNG_BASE,
> - "rng", NULL),
> - OF_DEV_AUXDATA("arm,primecell", NOMADIK_RTC_BASE,
> - "rtc-pl031", NULL),
> OF_DEV_AUXDATA("stericsson,fsmc-nand", NOMADIK_FSMC_BASE,
> - "fsmc-nand", &cpu8815_nand_data),
> + NULL, &cpu8815_nand_data),
> OF_DEV_AUXDATA("arm,primecell", NOMADIK_SDI_BASE,
> - "mmci", &mmcsd_plat_data),
> + NULL, &mmcsd_plat_data),
> { /* sentinel */ },
> };
>
> diff --git a/drivers/clk/clk-nomadik.c b/drivers/clk/clk-nomadik.c
> index 6b4c70f..19f197c 100644
> --- a/drivers/clk/clk-nomadik.c
> +++ b/drivers/clk/clk-nomadik.c
> @@ -3,24 +3,24 @@
> #include <linux/err.h>
> #include <linux/io.h>
> #include <linux/clk-provider.h>
> +#include <linux/of.h>
>
> /*
> * The Nomadik clock tree is described in the STN8815A12 DB V4.2
> * reference manual for the chip, page 94 ff.
> */
>
> +static const __initconst struct of_device_id cpu8815_clk_match[] = {
> + { .compatible = "fixed-clock", .data = of_fixed_clk_setup, },
> + { /* sentinel */ }
> +};
> +
> void __init nomadik_clk_init(void)
> {
> struct clk *clk;
>
> clk = clk_register_fixed_rate(NULL, "apb_pclk", NULL, CLK_IS_ROOT, 0);
> clk_register_clkdev(clk, "apb_pclk", NULL);
> - clk_register_clkdev(clk, NULL, "gpio.0");
> - clk_register_clkdev(clk, NULL, "gpio.1");
> - clk_register_clkdev(clk, NULL, "gpio.2");
> - clk_register_clkdev(clk, NULL, "gpio.3");
> - clk_register_clkdev(clk, NULL, "rng");
> - clk_register_clkdev(clk, NULL, "fsmc-nand");
>
> /*
> * The 2.4 MHz TIMCLK reference clock is active at boot time, this is
> @@ -32,17 +32,5 @@ void __init nomadik_clk_init(void)
> clk_register_clkdev(clk, NULL, "mtu0");
> clk_register_clkdev(clk, NULL, "mtu1");
>
> - /*
> - * At boot time, PLL2 is set to generate a set of fixed clocks,
> - * one of them is CLK48, the 48 MHz clock, routed to the UART, MMC/SD
> - * I2C, IrDA, USB and SSP blocks.
> - */
> - clk = clk_register_fixed_rate(NULL, "CLK48", NULL, CLK_IS_ROOT,
> - 48000000);
> - clk_register_clkdev(clk, NULL, "uart0");
> - clk_register_clkdev(clk, NULL, "uart1");
> - clk_register_clkdev(clk, NULL, "mmci");
> - clk_register_clkdev(clk, NULL, "ssp");
> - clk_register_clkdev(clk, NULL, "nmk-i2c.0");
> - clk_register_clkdev(clk, NULL, "nmk-i2c.1");
> + of_clk_init(cpu8815_clk_match);
> }
> --
> 1.8.1.4
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 3+ messages in thread
* [PATCH 3/4] ARM: nomadik: convert all clocks except timer to dt
@ 2013-04-20 13:08 Linus Walleij
0 siblings, 0 replies; 3+ messages in thread
From: Linus Walleij @ 2013-04-20 13:08 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: linux-kernel, Linus Walleij
This moves all Nomadik clocks except the one used for the
timer/clocksource over to the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
.../devicetree/bindings/arm/ste-nomadik.txt | 5 ++
arch/arm/boot/dts/ste-nomadik-stn8815.dtsi | 54 ++++++++++++++++++++++
arch/arm/mach-nomadik/cpu-8815.c | 20 +-------
drivers/clk/clk-nomadik.c | 26 +++--------
4 files changed, 68 insertions(+), 37 deletions(-)
diff --git a/Documentation/devicetree/bindings/arm/ste-nomadik.txt b/Documentation/devicetree/bindings/arm/ste-nomadik.txt
index 19bca04..6256ec3 100644
--- a/Documentation/devicetree/bindings/arm/ste-nomadik.txt
+++ b/Documentation/devicetree/bindings/arm/ste-nomadik.txt
@@ -3,6 +3,11 @@ ST-Ericsson Nomadik Device Tree Bindings
For various board the "board" node may contain specific properties
that pertain to this particular board, such as board-specific GPIOs.
+Required root node property: src
+- Nomadik System and reset controller used for basic chip control, clock
+ and reset line control.
+- compatible: must be "stericsson,nomadik,src"
+
Boards with the Nomadik SoC include:
S8815 "MiniKit" manufactured by Calao Systems:
diff --git a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
index 4a4aab3..f0df948 100644
--- a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
+++ b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
@@ -45,6 +45,7 @@
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <0>;
+ clocks = <&pclk>;
};
gpio1: gpio@101e5000 {
@@ -57,6 +58,7 @@
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <1>;
+ clocks = <&pclk>;
};
gpio2: gpio@101e6000 {
@@ -69,6 +71,7 @@
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <2>;
+ clocks = <&pclk>;
};
gpio3: gpio@101e7000 {
@@ -81,12 +84,50 @@
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <3>;
+ clocks = <&pclk>;
};
pinctrl {
compatible = "stericsson,nmk-pinctrl-stn8815";
};
+ src: src@101e0000 {
+ compatible = "stericsson,nomadik-src";
+ reg = <0x101e0000 0x1000>;
+ clocks {
+ /*
+ * Dummy clock for primecells
+ */
+ pclk: pclk@0 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <2400000>;
+ };
+ /*
+ * The 2.4 MHz TIMCLK reference clock is active at
+ * boot time, this is actually the MXTALCLK @19.2 MHz
+ * divided by 8. This clock is used by the timers and
+ * watchdog. See page 105 ff.
+ */
+ timclk: timclk@2.4M {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <2400000>;
+ };
+ /*
+ * At boot time, PLL2 is set to generate a set of
+ * fixed clocks, one of them is CLK48, the 48 MHz
+ * clock, routed to the UART, MMC/SD, I2C, IrDA,
+ * USB and SSP blocks.
+ */
+ clk48: clk48@48M {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <48000000>;
+ };
+ };
+ };
+
/* A NAND flash of 128 MiB */
fsmc: flash@40000000 {
compatible = "stericsson,fsmc-nand";
@@ -97,6 +138,7 @@
<0x41000000 0x2000>, /* NAND Base ADDR */
<0x40800000 0x2000>; /* NAND Base CMD */
reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd";
+ clocks = <&pclk>;
status = "okay";
partition@0 {
@@ -211,6 +253,8 @@
reg = <0x101fd000 0x1000>;
interrupt-parent = <&vica>;
interrupts = <12>;
+ clocks = <&clk48>, <&pclk>;
+ clock-names = "uartclk", "apb_pclk";
};
uart1: uart@101fb000 {
@@ -218,6 +262,8 @@
reg = <0x101fb000 0x1000>;
interrupt-parent = <&vica>;
interrupts = <17>;
+ clocks = <&clk48>, <&pclk>;
+ clock-names = "uartclk", "apb_pclk";
};
uart2: uart@101f2000 {
@@ -225,17 +271,23 @@
reg = <0x101f2000 0x1000>;
interrupt-parent = <&vica>;
interrupts = <28>;
+ clocks = <&clk48>, <&pclk>;
+ clock-names = "uartclk", "apb_pclk";
status = "disabled";
};
rng: rng@101b0000 {
compatible = "arm,primecell";
reg = <0x101b0000 0x1000>;
+ clocks = <&clk48>, <&pclk>;
+ clock-names = "rng", "apb_pclk";
};
rtc: rtc@101e8000 {
compatible = "arm,pl031", "arm,primecell";
reg = <0x101e8000 0x1000>;
+ clocks = <&pclk>;
+ clock-names = "apb_pclk";
interrupt-parent = <&vica>;
interrupts = <10>;
};
@@ -243,6 +295,8 @@
mmcsd: sdi@101f6000 {
compatible = "arm,pl18x", "arm,primecell";
reg = <0x101f6000 0x1000>;
+ clocks = <&clk48>, <&pclk>;
+ clock-names = "mclk", "apb_pclk";
interrupt-parent = <&vica>;
interrupts = <22>;
max-frequency = <48000000>;
diff --git a/arch/arm/mach-nomadik/cpu-8815.c b/arch/arm/mach-nomadik/cpu-8815.c
index 59f6ff5..0e2c5e0 100644
--- a/arch/arm/mach-nomadik/cpu-8815.c
+++ b/arch/arm/mach-nomadik/cpu-8815.c
@@ -280,28 +280,12 @@ device_initcall(cpu8815_mmcsd_init);
/* These are mostly to get the right device names for the clock lookups */
static struct of_dev_auxdata cpu8815_auxdata_lookup[] __initdata = {
- OF_DEV_AUXDATA("st,nomadik-gpio", NOMADIK_GPIO0_BASE,
- "gpio.0", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", NOMADIK_GPIO1_BASE,
- "gpio.1", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", NOMADIK_GPIO2_BASE,
- "gpio.2", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", NOMADIK_GPIO3_BASE,
- "gpio.3", NULL),
OF_DEV_AUXDATA("stericsson,nmk-pinctrl-stn8815", 0,
"pinctrl-stn8815", NULL),
- OF_DEV_AUXDATA("arm,primecell", NOMADIK_UART0_BASE,
- "uart0", NULL),
- OF_DEV_AUXDATA("arm,primecell", NOMADIK_UART1_BASE,
- "uart1", NULL),
- OF_DEV_AUXDATA("arm,primecell", NOMADIK_RNG_BASE,
- "rng", NULL),
- OF_DEV_AUXDATA("arm,primecell", NOMADIK_RTC_BASE,
- "rtc-pl031", NULL),
OF_DEV_AUXDATA("stericsson,fsmc-nand", NOMADIK_FSMC_BASE,
- "fsmc-nand", &cpu8815_nand_data),
+ NULL, &cpu8815_nand_data),
OF_DEV_AUXDATA("arm,primecell", NOMADIK_SDI_BASE,
- "mmci", &mmcsd_plat_data),
+ NULL, &mmcsd_plat_data),
{ /* sentinel */ },
};
diff --git a/drivers/clk/clk-nomadik.c b/drivers/clk/clk-nomadik.c
index 6b4c70f..19f197c 100644
--- a/drivers/clk/clk-nomadik.c
+++ b/drivers/clk/clk-nomadik.c
@@ -3,24 +3,24 @@
#include <linux/err.h>
#include <linux/io.h>
#include <linux/clk-provider.h>
+#include <linux/of.h>
/*
* The Nomadik clock tree is described in the STN8815A12 DB V4.2
* reference manual for the chip, page 94 ff.
*/
+static const __initconst struct of_device_id cpu8815_clk_match[] = {
+ { .compatible = "fixed-clock", .data = of_fixed_clk_setup, },
+ { /* sentinel */ }
+};
+
void __init nomadik_clk_init(void)
{
struct clk *clk;
clk = clk_register_fixed_rate(NULL, "apb_pclk", NULL, CLK_IS_ROOT, 0);
clk_register_clkdev(clk, "apb_pclk", NULL);
- clk_register_clkdev(clk, NULL, "gpio.0");
- clk_register_clkdev(clk, NULL, "gpio.1");
- clk_register_clkdev(clk, NULL, "gpio.2");
- clk_register_clkdev(clk, NULL, "gpio.3");
- clk_register_clkdev(clk, NULL, "rng");
- clk_register_clkdev(clk, NULL, "fsmc-nand");
/*
* The 2.4 MHz TIMCLK reference clock is active at boot time, this is
@@ -32,17 +32,5 @@ void __init nomadik_clk_init(void)
clk_register_clkdev(clk, NULL, "mtu0");
clk_register_clkdev(clk, NULL, "mtu1");
- /*
- * At boot time, PLL2 is set to generate a set of fixed clocks,
- * one of them is CLK48, the 48 MHz clock, routed to the UART, MMC/SD
- * I2C, IrDA, USB and SSP blocks.
- */
- clk = clk_register_fixed_rate(NULL, "CLK48", NULL, CLK_IS_ROOT,
- 48000000);
- clk_register_clkdev(clk, NULL, "uart0");
- clk_register_clkdev(clk, NULL, "uart1");
- clk_register_clkdev(clk, NULL, "mmci");
- clk_register_clkdev(clk, NULL, "ssp");
- clk_register_clkdev(clk, NULL, "nmk-i2c.0");
- clk_register_clkdev(clk, NULL, "nmk-i2c.1");
+ of_clk_init(cpu8815_clk_match);
}
--
1.8.1.4
^ permalink raw reply related [flat|nested] 3+ messages in thread
end of thread, other threads:[~2013-04-22 22:01 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2013-04-20 14:09 [PATCH 3/4] ARM: nomadik: convert all clocks except timer to dt Linus Walleij
2013-04-22 22:01 ` Mike Turquette
-- strict thread matches above, loose matches on Subject: below --
2013-04-20 13:08 Linus Walleij
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.