From: Tony Lindgren <tony@atomide.com>
To: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Subject: [PATCH 5/6] ARM: OMAP2+: Remove omap4 pdata for USB
Date: Fri, 17 May 2013 12:18:01 -0700 [thread overview]
Message-ID: <20130517191801.468.56731.stgit@localhost> (raw)
In-Reply-To: <20130517191304.468.73487.stgit@localhost>
This is no longer needed as omap4 is now booted
using device tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/devices.c | 45 ---------
arch/arm/mach-omap2/usb-host.c | 194 ----------------------------------------
arch/arm/mach-omap2/usb-musb.c | 3 -
3 files changed, 242 deletions(-)
diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c
index 4269fc1..0fd3834 100644
--- a/arch/arm/mach-omap2/devices.c
+++ b/arch/arm/mach-omap2/devices.c
@@ -20,7 +20,6 @@
#include <linux/pinctrl/machine.h>
#include <linux/platform_data/omap4-keypad.h>
#include <linux/platform_data/omap_ocp2scp.h>
-#include <linux/usb/omap_control_usb.h>
#include <asm/mach-types.h>
#include <asm/mach/map.h>
@@ -253,49 +252,6 @@ static inline void omap_init_camera(void)
#endif
}
-#if IS_ENABLED(CONFIG_OMAP_CONTROL_USB)
-static struct omap_control_usb_platform_data omap4_control_usb_pdata = {
- .type = 1,
-};
-
-struct resource omap4_control_usb_res[] = {
- {
- .name = "control_dev_conf",
- .start = 0x4a002300,
- .end = 0x4a002303,
- .flags = IORESOURCE_MEM,
- },
- {
- .name = "otghs_control",
- .start = 0x4a00233c,
- .end = 0x4a00233f,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct platform_device omap4_control_usb = {
- .name = "omap-control-usb",
- .id = -1,
- .dev = {
- .platform_data = &omap4_control_usb_pdata,
- },
- .num_resources = 2,
- .resource = omap4_control_usb_res,
-};
-
-static inline void __init omap_init_control_usb(void)
-{
- if (!cpu_is_omap44xx())
- return;
-
- if (platform_device_register(&omap4_control_usb))
- pr_err("Error registering omap_control_usb device\n");
-}
-
-#else
-static inline void omap_init_control_usb(void) { }
-#endif /* CONFIG_OMAP_CONTROL_USB */
-
int __init omap4_keyboard_init(struct omap4_keypad_platform_data
*sdp4430_keypad_data, struct omap_board_data *bdata)
{
@@ -651,7 +607,6 @@ static int __init omap2_init_devices(void)
omap_init_mbox();
/* If dtb is there, the devices will be created dynamically */
if (!of_have_populated_dt()) {
- omap_init_control_usb();
omap_init_dmic();
omap_init_mcpdm();
omap_init_mcspi();
diff --git a/arch/arm/mach-omap2/usb-host.c b/arch/arm/mach-omap2/usb-host.c
index aa27d7f..544c92b 100644
--- a/arch/arm/mach-omap2/usb-host.c
+++ b/arch/arm/mach-omap2/usb-host.c
@@ -188,125 +188,6 @@ static void __init setup_ehci_io_mux(const enum usbhs_omap_port_mode *port_mode)
return;
}
-static
-void __init setup_4430ehci_io_mux(const enum usbhs_omap_port_mode *port_mode)
-{
- switch (port_mode[0]) {
- case OMAP_EHCI_PORT_MODE_PHY:
- omap_mux_init_signal("usbb1_ulpiphy_stp",
- OMAP_PIN_OUTPUT);
- omap_mux_init_signal("usbb1_ulpiphy_clk",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpiphy_dir",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpiphy_nxt",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpiphy_dat0",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpiphy_dat1",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpiphy_dat2",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpiphy_dat3",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpiphy_dat4",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpiphy_dat5",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpiphy_dat6",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpiphy_dat7",
- OMAP_PIN_INPUT_PULLDOWN);
- break;
- case OMAP_EHCI_PORT_MODE_TLL:
- omap_mux_init_signal("usbb1_ulpitll_stp",
- OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_signal("usbb1_ulpitll_clk",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpitll_dir",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpitll_nxt",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpitll_dat0",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpitll_dat1",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpitll_dat2",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpitll_dat3",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpitll_dat4",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpitll_dat5",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpitll_dat6",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpitll_dat7",
- OMAP_PIN_INPUT_PULLDOWN);
- break;
- case OMAP_USBHS_PORT_MODE_UNUSED:
- default:
- break;
- }
- switch (port_mode[1]) {
- case OMAP_EHCI_PORT_MODE_PHY:
- omap_mux_init_signal("usbb2_ulpiphy_stp",
- OMAP_PIN_OUTPUT);
- omap_mux_init_signal("usbb2_ulpiphy_clk",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpiphy_dir",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpiphy_nxt",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpiphy_dat0",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpiphy_dat1",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpiphy_dat2",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpiphy_dat3",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpiphy_dat4",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpiphy_dat5",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpiphy_dat6",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpiphy_dat7",
- OMAP_PIN_INPUT_PULLDOWN);
- break;
- case OMAP_EHCI_PORT_MODE_TLL:
- omap_mux_init_signal("usbb2_ulpitll_stp",
- OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_signal("usbb2_ulpitll_clk",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpitll_dir",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpitll_nxt",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpitll_dat0",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpitll_dat1",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpitll_dat2",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpitll_dat3",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpitll_dat4",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpitll_dat5",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpitll_dat6",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpitll_dat7",
- OMAP_PIN_INPUT_PULLDOWN);
- break;
- case OMAP_USBHS_PORT_MODE_UNUSED:
- default:
- break;
- }
-}
-
static void __init setup_ohci_io_mux(const enum usbhs_omap_port_mode *port_mode)
{
switch (port_mode[0]) {
@@ -404,78 +285,6 @@ static void __init setup_ohci_io_mux(const enum usbhs_omap_port_mode *port_mode)
}
}
-static
-void __init setup_4430ohci_io_mux(const enum usbhs_omap_port_mode *port_mode)
-{
- switch (port_mode[0]) {
- case OMAP_OHCI_PORT_MODE_PHY_6PIN_DATSE0:
- case OMAP_OHCI_PORT_MODE_PHY_6PIN_DPDM:
- case OMAP_OHCI_PORT_MODE_TLL_6PIN_DATSE0:
- case OMAP_OHCI_PORT_MODE_TLL_6PIN_DPDM:
- omap_mux_init_signal("usbb1_mm_rxdp",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_mm_rxdm",
- OMAP_PIN_INPUT_PULLDOWN);
-
- case OMAP_OHCI_PORT_MODE_PHY_4PIN_DPDM:
- case OMAP_OHCI_PORT_MODE_TLL_4PIN_DPDM:
- omap_mux_init_signal("usbb1_mm_rxrcv",
- OMAP_PIN_INPUT_PULLDOWN);
-
- case OMAP_OHCI_PORT_MODE_PHY_3PIN_DATSE0:
- case OMAP_OHCI_PORT_MODE_TLL_3PIN_DATSE0:
- omap_mux_init_signal("usbb1_mm_txen",
- OMAP_PIN_INPUT_PULLDOWN);
-
-
- case OMAP_OHCI_PORT_MODE_TLL_2PIN_DATSE0:
- case OMAP_OHCI_PORT_MODE_TLL_2PIN_DPDM:
- omap_mux_init_signal("usbb1_mm_txdat",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_mm_txse0",
- OMAP_PIN_INPUT_PULLDOWN);
- break;
-
- case OMAP_USBHS_PORT_MODE_UNUSED:
- default:
- break;
- }
-
- switch (port_mode[1]) {
- case OMAP_OHCI_PORT_MODE_PHY_6PIN_DATSE0:
- case OMAP_OHCI_PORT_MODE_PHY_6PIN_DPDM:
- case OMAP_OHCI_PORT_MODE_TLL_6PIN_DATSE0:
- case OMAP_OHCI_PORT_MODE_TLL_6PIN_DPDM:
- omap_mux_init_signal("usbb2_mm_rxdp",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_mm_rxdm",
- OMAP_PIN_INPUT_PULLDOWN);
-
- case OMAP_OHCI_PORT_MODE_PHY_4PIN_DPDM:
- case OMAP_OHCI_PORT_MODE_TLL_4PIN_DPDM:
- omap_mux_init_signal("usbb2_mm_rxrcv",
- OMAP_PIN_INPUT_PULLDOWN);
-
- case OMAP_OHCI_PORT_MODE_PHY_3PIN_DATSE0:
- case OMAP_OHCI_PORT_MODE_TLL_3PIN_DATSE0:
- omap_mux_init_signal("usbb2_mm_txen",
- OMAP_PIN_INPUT_PULLDOWN);
-
-
- case OMAP_OHCI_PORT_MODE_TLL_2PIN_DATSE0:
- case OMAP_OHCI_PORT_MODE_TLL_2PIN_DPDM:
- omap_mux_init_signal("usbb2_mm_txdat",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_mm_txse0",
- OMAP_PIN_INPUT_PULLDOWN);
- break;
-
- case OMAP_USBHS_PORT_MODE_UNUSED:
- default:
- break;
- }
-}
-
void __init usbhs_init(struct usbhs_omap_platform_data *pdata)
{
struct omap_hwmod *uhh_hwm, *tll_hwm;
@@ -489,9 +298,6 @@ void __init usbhs_init(struct usbhs_omap_platform_data *pdata)
if (omap_rev() <= OMAP3430_REV_ES2_1)
pdata->single_ulpi_bypass = true;
- } else if (cpu_is_omap44xx()) {
- setup_4430ehci_io_mux(pdata->port_mode);
- setup_4430ohci_io_mux(pdata->port_mode);
}
uhh_hwm = omap_hwmod_lookup(USBHS_UHH_HWMODNAME);
diff --git a/arch/arm/mach-omap2/usb-musb.c b/arch/arm/mach-omap2/usb-musb.c
index 3242a55..8c4de270 100644
--- a/arch/arm/mach-omap2/usb-musb.c
+++ b/arch/arm/mach-omap2/usb-musb.c
@@ -85,9 +85,6 @@ void __init usb_musb_init(struct omap_musb_board_data *musb_board_data)
musb_plat.mode = board_data->mode;
musb_plat.extvbus = board_data->extvbus;
- if (cpu_is_omap44xx())
- musb_plat.has_mailbox = true;
-
if (soc_is_am35xx()) {
oh_name = "am35x_otg_hs";
name = "musb-am35x";
WARNING: multiple messages have this Message-ID (diff)
From: tony@atomide.com (Tony Lindgren)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 5/6] ARM: OMAP2+: Remove omap4 pdata for USB
Date: Fri, 17 May 2013 12:18:01 -0700 [thread overview]
Message-ID: <20130517191801.468.56731.stgit@localhost> (raw)
In-Reply-To: <20130517191304.468.73487.stgit@localhost>
This is no longer needed as omap4 is now booted
using device tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/devices.c | 45 ---------
arch/arm/mach-omap2/usb-host.c | 194 ----------------------------------------
arch/arm/mach-omap2/usb-musb.c | 3 -
3 files changed, 242 deletions(-)
diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c
index 4269fc1..0fd3834 100644
--- a/arch/arm/mach-omap2/devices.c
+++ b/arch/arm/mach-omap2/devices.c
@@ -20,7 +20,6 @@
#include <linux/pinctrl/machine.h>
#include <linux/platform_data/omap4-keypad.h>
#include <linux/platform_data/omap_ocp2scp.h>
-#include <linux/usb/omap_control_usb.h>
#include <asm/mach-types.h>
#include <asm/mach/map.h>
@@ -253,49 +252,6 @@ static inline void omap_init_camera(void)
#endif
}
-#if IS_ENABLED(CONFIG_OMAP_CONTROL_USB)
-static struct omap_control_usb_platform_data omap4_control_usb_pdata = {
- .type = 1,
-};
-
-struct resource omap4_control_usb_res[] = {
- {
- .name = "control_dev_conf",
- .start = 0x4a002300,
- .end = 0x4a002303,
- .flags = IORESOURCE_MEM,
- },
- {
- .name = "otghs_control",
- .start = 0x4a00233c,
- .end = 0x4a00233f,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct platform_device omap4_control_usb = {
- .name = "omap-control-usb",
- .id = -1,
- .dev = {
- .platform_data = &omap4_control_usb_pdata,
- },
- .num_resources = 2,
- .resource = omap4_control_usb_res,
-};
-
-static inline void __init omap_init_control_usb(void)
-{
- if (!cpu_is_omap44xx())
- return;
-
- if (platform_device_register(&omap4_control_usb))
- pr_err("Error registering omap_control_usb device\n");
-}
-
-#else
-static inline void omap_init_control_usb(void) { }
-#endif /* CONFIG_OMAP_CONTROL_USB */
-
int __init omap4_keyboard_init(struct omap4_keypad_platform_data
*sdp4430_keypad_data, struct omap_board_data *bdata)
{
@@ -651,7 +607,6 @@ static int __init omap2_init_devices(void)
omap_init_mbox();
/* If dtb is there, the devices will be created dynamically */
if (!of_have_populated_dt()) {
- omap_init_control_usb();
omap_init_dmic();
omap_init_mcpdm();
omap_init_mcspi();
diff --git a/arch/arm/mach-omap2/usb-host.c b/arch/arm/mach-omap2/usb-host.c
index aa27d7f..544c92b 100644
--- a/arch/arm/mach-omap2/usb-host.c
+++ b/arch/arm/mach-omap2/usb-host.c
@@ -188,125 +188,6 @@ static void __init setup_ehci_io_mux(const enum usbhs_omap_port_mode *port_mode)
return;
}
-static
-void __init setup_4430ehci_io_mux(const enum usbhs_omap_port_mode *port_mode)
-{
- switch (port_mode[0]) {
- case OMAP_EHCI_PORT_MODE_PHY:
- omap_mux_init_signal("usbb1_ulpiphy_stp",
- OMAP_PIN_OUTPUT);
- omap_mux_init_signal("usbb1_ulpiphy_clk",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpiphy_dir",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpiphy_nxt",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpiphy_dat0",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpiphy_dat1",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpiphy_dat2",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpiphy_dat3",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpiphy_dat4",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpiphy_dat5",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpiphy_dat6",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpiphy_dat7",
- OMAP_PIN_INPUT_PULLDOWN);
- break;
- case OMAP_EHCI_PORT_MODE_TLL:
- omap_mux_init_signal("usbb1_ulpitll_stp",
- OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_signal("usbb1_ulpitll_clk",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpitll_dir",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpitll_nxt",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpitll_dat0",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpitll_dat1",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpitll_dat2",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpitll_dat3",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpitll_dat4",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpitll_dat5",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpitll_dat6",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_ulpitll_dat7",
- OMAP_PIN_INPUT_PULLDOWN);
- break;
- case OMAP_USBHS_PORT_MODE_UNUSED:
- default:
- break;
- }
- switch (port_mode[1]) {
- case OMAP_EHCI_PORT_MODE_PHY:
- omap_mux_init_signal("usbb2_ulpiphy_stp",
- OMAP_PIN_OUTPUT);
- omap_mux_init_signal("usbb2_ulpiphy_clk",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpiphy_dir",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpiphy_nxt",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpiphy_dat0",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpiphy_dat1",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpiphy_dat2",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpiphy_dat3",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpiphy_dat4",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpiphy_dat5",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpiphy_dat6",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpiphy_dat7",
- OMAP_PIN_INPUT_PULLDOWN);
- break;
- case OMAP_EHCI_PORT_MODE_TLL:
- omap_mux_init_signal("usbb2_ulpitll_stp",
- OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_signal("usbb2_ulpitll_clk",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpitll_dir",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpitll_nxt",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpitll_dat0",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpitll_dat1",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpitll_dat2",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpitll_dat3",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpitll_dat4",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpitll_dat5",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpitll_dat6",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_ulpitll_dat7",
- OMAP_PIN_INPUT_PULLDOWN);
- break;
- case OMAP_USBHS_PORT_MODE_UNUSED:
- default:
- break;
- }
-}
-
static void __init setup_ohci_io_mux(const enum usbhs_omap_port_mode *port_mode)
{
switch (port_mode[0]) {
@@ -404,78 +285,6 @@ static void __init setup_ohci_io_mux(const enum usbhs_omap_port_mode *port_mode)
}
}
-static
-void __init setup_4430ohci_io_mux(const enum usbhs_omap_port_mode *port_mode)
-{
- switch (port_mode[0]) {
- case OMAP_OHCI_PORT_MODE_PHY_6PIN_DATSE0:
- case OMAP_OHCI_PORT_MODE_PHY_6PIN_DPDM:
- case OMAP_OHCI_PORT_MODE_TLL_6PIN_DATSE0:
- case OMAP_OHCI_PORT_MODE_TLL_6PIN_DPDM:
- omap_mux_init_signal("usbb1_mm_rxdp",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_mm_rxdm",
- OMAP_PIN_INPUT_PULLDOWN);
-
- case OMAP_OHCI_PORT_MODE_PHY_4PIN_DPDM:
- case OMAP_OHCI_PORT_MODE_TLL_4PIN_DPDM:
- omap_mux_init_signal("usbb1_mm_rxrcv",
- OMAP_PIN_INPUT_PULLDOWN);
-
- case OMAP_OHCI_PORT_MODE_PHY_3PIN_DATSE0:
- case OMAP_OHCI_PORT_MODE_TLL_3PIN_DATSE0:
- omap_mux_init_signal("usbb1_mm_txen",
- OMAP_PIN_INPUT_PULLDOWN);
-
-
- case OMAP_OHCI_PORT_MODE_TLL_2PIN_DATSE0:
- case OMAP_OHCI_PORT_MODE_TLL_2PIN_DPDM:
- omap_mux_init_signal("usbb1_mm_txdat",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb1_mm_txse0",
- OMAP_PIN_INPUT_PULLDOWN);
- break;
-
- case OMAP_USBHS_PORT_MODE_UNUSED:
- default:
- break;
- }
-
- switch (port_mode[1]) {
- case OMAP_OHCI_PORT_MODE_PHY_6PIN_DATSE0:
- case OMAP_OHCI_PORT_MODE_PHY_6PIN_DPDM:
- case OMAP_OHCI_PORT_MODE_TLL_6PIN_DATSE0:
- case OMAP_OHCI_PORT_MODE_TLL_6PIN_DPDM:
- omap_mux_init_signal("usbb2_mm_rxdp",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_mm_rxdm",
- OMAP_PIN_INPUT_PULLDOWN);
-
- case OMAP_OHCI_PORT_MODE_PHY_4PIN_DPDM:
- case OMAP_OHCI_PORT_MODE_TLL_4PIN_DPDM:
- omap_mux_init_signal("usbb2_mm_rxrcv",
- OMAP_PIN_INPUT_PULLDOWN);
-
- case OMAP_OHCI_PORT_MODE_PHY_3PIN_DATSE0:
- case OMAP_OHCI_PORT_MODE_TLL_3PIN_DATSE0:
- omap_mux_init_signal("usbb2_mm_txen",
- OMAP_PIN_INPUT_PULLDOWN);
-
-
- case OMAP_OHCI_PORT_MODE_TLL_2PIN_DATSE0:
- case OMAP_OHCI_PORT_MODE_TLL_2PIN_DPDM:
- omap_mux_init_signal("usbb2_mm_txdat",
- OMAP_PIN_INPUT_PULLDOWN);
- omap_mux_init_signal("usbb2_mm_txse0",
- OMAP_PIN_INPUT_PULLDOWN);
- break;
-
- case OMAP_USBHS_PORT_MODE_UNUSED:
- default:
- break;
- }
-}
-
void __init usbhs_init(struct usbhs_omap_platform_data *pdata)
{
struct omap_hwmod *uhh_hwm, *tll_hwm;
@@ -489,9 +298,6 @@ void __init usbhs_init(struct usbhs_omap_platform_data *pdata)
if (omap_rev() <= OMAP3430_REV_ES2_1)
pdata->single_ulpi_bypass = true;
- } else if (cpu_is_omap44xx()) {
- setup_4430ehci_io_mux(pdata->port_mode);
- setup_4430ohci_io_mux(pdata->port_mode);
}
uhh_hwm = omap_hwmod_lookup(USBHS_UHH_HWMODNAME);
diff --git a/arch/arm/mach-omap2/usb-musb.c b/arch/arm/mach-omap2/usb-musb.c
index 3242a55..8c4de270 100644
--- a/arch/arm/mach-omap2/usb-musb.c
+++ b/arch/arm/mach-omap2/usb-musb.c
@@ -85,9 +85,6 @@ void __init usb_musb_init(struct omap_musb_board_data *musb_board_data)
musb_plat.mode = board_data->mode;
musb_plat.extvbus = board_data->extvbus;
- if (cpu_is_omap44xx())
- musb_plat.has_mailbox = true;
-
if (soc_is_am35xx()) {
oh_name = "am35x_otg_hs";
name = "musb-am35x";
next prev parent reply other threads:[~2013-05-17 19:18 UTC|newest]
Thread overview: 100+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-05-17 19:17 [PATCH 0/6] Drop legacy booting for omap4 for v3.11, boot with device tree only Tony Lindgren
2013-05-17 19:17 ` Tony Lindgren
2013-05-17 19:17 ` [PATCH 1/6] ARM: OMAP2+: Remove board-4430sdp.c Tony Lindgren
2013-05-17 19:17 ` Tony Lindgren
2013-05-20 9:54 ` Russell King - ARM Linux
2013-05-20 9:54 ` Russell King - ARM Linux
2013-05-20 17:10 ` Tony Lindgren
2013-05-20 17:10 ` Tony Lindgren
2013-07-06 13:10 ` Russell King - ARM Linux
2013-07-06 13:10 ` Russell King - ARM Linux
2013-07-06 13:36 ` Russell King - ARM Linux
2013-07-06 13:36 ` Russell King - ARM Linux
2013-07-08 9:34 ` Tony Lindgren
2013-07-08 9:34 ` Tony Lindgren
2013-07-08 14:21 ` Russell King - ARM Linux
2013-07-08 14:21 ` Russell King - ARM Linux
2013-07-09 8:23 ` Tony Lindgren
2013-07-09 8:23 ` Tony Lindgren
2013-07-12 9:09 ` Peter Ujfalusi
2013-07-12 9:09 ` Peter Ujfalusi
2013-07-22 9:40 ` Tomi Valkeinen
2013-07-22 9:40 ` Tomi Valkeinen
2013-10-27 13:26 ` Javier Martinez Canillas
2013-10-27 13:26 ` Javier Martinez Canillas
2013-10-28 13:32 ` Tomi Valkeinen
2013-10-28 13:32 ` Tomi Valkeinen
2013-10-28 14:25 ` Javier Martinez Canillas
2013-10-28 14:25 ` Javier Martinez Canillas
2013-07-13 2:31 ` Olof Johansson
2013-07-13 2:31 ` Olof Johansson
2013-07-13 3:10 ` Olof Johansson
2013-07-13 3:10 ` Olof Johansson
2013-07-15 6:55 ` Tony Lindgren
2013-07-15 6:55 ` Tony Lindgren
2013-07-06 21:36 ` Arnd Bergmann
2013-07-06 21:36 ` Arnd Bergmann
2013-07-06 23:37 ` debugging options (was: Re: [PATCH 1/6] ARM: OMAP2+: Remove board-4430sdp.c) Russell King - ARM Linux
2013-07-06 23:37 ` Russell King - ARM Linux
2013-05-17 19:17 ` [PATCH 2/6] ARM: OMAP2+: Remove board-omap4panda.c Tony Lindgren
2013-05-17 19:17 ` Tony Lindgren
2013-06-03 15:28 ` Ming Lei
2013-06-03 15:28 ` Ming Lei
2013-06-12 16:31 ` Tony Lindgren
2013-06-12 16:31 ` Tony Lindgren
2013-06-12 17:14 ` Tony Lindgren
2013-06-12 17:14 ` Tony Lindgren
2013-06-13 9:21 ` Sricharan R
2013-06-13 9:21 ` Sricharan R
2013-06-13 10:12 ` Sricharan R
2013-06-13 10:12 ` Sricharan R
2013-06-13 11:05 ` Tony Lindgren
2013-06-13 11:05 ` Tony Lindgren
2013-06-13 13:36 ` Ming Lei
2013-06-13 13:36 ` Ming Lei
2013-06-14 13:31 ` Ming Lei
2013-06-14 13:31 ` Ming Lei
2013-06-14 13:58 ` Ming Lei
2013-06-14 13:58 ` Ming Lei
2013-06-17 7:42 ` Sricharan R
2013-06-17 7:42 ` Sricharan R
2013-06-17 8:06 ` Arnaud Patard
2013-06-17 8:06 ` Arnaud Patard (Rtp)
2013-06-17 8:16 ` Ming Lei
2013-06-17 8:16 ` Ming Lei
2013-06-17 8:27 ` Tony Lindgren
2013-06-17 8:27 ` Tony Lindgren
2013-06-17 8:41 ` Ming Lei
2013-06-17 8:41 ` Ming Lei
2013-06-17 8:49 ` Tony Lindgren
2013-06-17 8:49 ` Tony Lindgren
2013-06-17 8:24 ` Tony Lindgren
2013-06-17 8:24 ` Tony Lindgren
2013-06-17 9:46 ` Arnaud Patard
2013-06-17 9:46 ` Arnaud Patard (Rtp)
2013-06-17 10:26 ` Tony Lindgren
2013-06-17 10:26 ` Tony Lindgren
2013-06-18 11:27 ` Tony Lindgren
2013-06-18 11:27 ` Tony Lindgren
2013-06-19 9:45 ` Arnaud Patard
2013-06-19 9:45 ` Arnaud Patard (Rtp)
2013-06-19 9:58 ` Tony Lindgren
2013-06-19 9:58 ` Tony Lindgren
2013-06-20 7:29 ` Arnaud Patard
2013-06-20 7:29 ` Arnaud Patard (Rtp)
2013-06-21 6:01 ` Tony Lindgren
2013-06-21 6:01 ` Tony Lindgren
2013-05-17 19:17 ` [PATCH 3/6] ARM: OMAP2+: Remove legacy mux data for omap4 Tony Lindgren
2013-05-17 19:17 ` Tony Lindgren
2013-05-17 19:17 ` [PATCH 4/6] ARM: OMAP2+: Remove omap4 pdata from hsmmc.c Tony Lindgren
2013-05-17 19:17 ` Tony Lindgren
2013-05-17 19:18 ` Tony Lindgren [this message]
2013-05-17 19:18 ` [PATCH 5/6] ARM: OMAP2+: Remove omap4 pdata for USB Tony Lindgren
2013-05-17 19:18 ` [PATCH 6/6] ARM: OMAP2+: Remove omap4 ocp2scp pdata Tony Lindgren
2013-05-17 19:18 ` Tony Lindgren
2013-05-17 20:05 ` Felipe Balbi
2013-05-17 20:05 ` Felipe Balbi
2013-05-21 11:53 ` Kishon Vijay Abraham I
2013-05-21 11:53 ` Kishon Vijay Abraham I
2013-06-07 10:05 ` [PATCH 0/6] Drop legacy booting for omap4 for v3.11, boot with device tree only Tomi Valkeinen
2013-06-07 10:05 ` Tomi Valkeinen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20130517191801.468.56731.stgit@localhost \
--to=tony@atomide.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-omap@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.