From: Sricharan R <r.sricharan@ti.com>
To: Ming Lei <tom.leiming@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>,
linux-omap@vger.kernel.org, linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH 2/6] ARM: OMAP2+: Remove board-omap4panda.c
Date: Mon, 17 Jun 2013 13:12:05 +0530 [thread overview]
Message-ID: <51BEBDCD.3060104@ti.com> (raw)
In-Reply-To: <CACVXFVNzAMrkhrAMAmQ7ZdJdby2O4VdoD8BVHRF-O=rPKQMqbw@mail.gmail.com>
On Friday 14 June 2013 07:28 PM, Ming Lei wrote:
> On Fri, Jun 14, 2013 at 9:31 PM, Ming Lei <tom.leiming@gmail.com> wrote:
>> On Thu, Jun 13, 2013 at 6:12 PM, Sricharan R <r.sricharan@ti.com> wrote:
>>> On Thursday 13 June 2013 02:51 PM, Sricharan R wrote:
>>>> Hi Tony,
>>>> On Wednesday 12 June 2013 10:44 PM, Tony Lindgren wrote:
>>>>> * Tony Lindgren <tony@atomide.com> [130612 09:37]:
>>>>>> * Ming Lei <tom.leiming@gmail.com> [130603 08:34]:
>>>>>>> Hi,
>>>>>>>
>>>>>>> On Sat, May 18, 2013 at 3:17 AM, Tony Lindgren <tony@atomide.com> wrote:
>>>>>>>> We can now boot with device tree. If you don't want to update u-boot,
>>>>>>>> you can boot with appended DTB with the following instructions:
>>>>>>>>
>>>>>>>> 1. Make sure you have the appended DTB support in .config
>>>>>>>>
>>>>>>>> CONFIG_ARM_APPENDED_DTB=y
>>>>>>>> CONFIG_ARM_ATAG_DTB_COMPAT=y
>>>>>>>> CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND=y
>>>>>>>>
>>>>>>>> 2. Build the zImage
>>>>>>>>
>>>>>>>> $ ARCH=arm CROSS_COMPILE=... make zImage
>>>>>>>>
>>>>>>>> 3. Build the device tree blobs
>>>>>>>>
>>>>>>>> $ ARCH=arm CROSS_COMPILE=... make dtbs
>>>>>>>>
>>>>>>>> 4. Append the correct panda dtb to zImage
>>>>>>>>
>>>>>>>> Depending on your hardware it's omap4-panda.dtb, omap4-panda-a4.dtb
>>>>>>>> or omap4-panda-es.dtb.
>>>>>>>>
>>>>>>>> $ cat arch/arm/boot/zImage arch/arm/boot/dts/omap4-panda-es.dtb > /tmp/appended
>>>>>>>>
>>>>>>>> 5. Use mkimage to produce the appended device tree uImage
>>>>>>>>
>>>>>>>> $ mkimage -A arm -O linux -T kernel -C none -a 0x80008000 -e 0x80008000 \
>>>>>>>> -n "Linux" -d /tmp/appended /tmp/uImage
>>>>>>> I followed the above steps and tried devicetree on Pandaboard against
>>>>>>> 3.10.0-rc3-next-20130528, and the board will hang during boot, but works
>>>>>>> well with legacy mode.
>>>>>>>
>>>>>>> Hardware: Pandaboard A1
>>>>>>> dtb: omap4-panda.dtb
>>>>>>>
>>>>>>> See 'dmesg' on below link:
>>>>>>>
>>>>>>> http://kernel.ubuntu.com/~ming/up/panda-dts.dmesg
>>>>>>>
>>>>>> Hmm looks like it boots to init. Maybe add initcall_debug to the cmdline in
>>>>>> case there's some late_initcall that causes the issue. It's probably some
>>>>>> trivial issue causing it.
>>>>> Sricharan, maybe give this a quick try if you have the original pandaboard?
>>>>> I only have pandaboard es.
>>>>>
>>>>> Regards,
>>>>>
>>>>> Tony
>>>> I tried your cleanup branch omap-for-v3.11/cleanup on panda board and it booted
>>>> to prompt fine.
>>>> Hardware: Pandaboard A1 dtb: omap4-panda.dtb
>>>>
>>>> git pull on linux-next branch was not working though.
>>>>
>>> Ok, tested in linux-next as well and it booted fine with DTB.
>>> HW: OMAP4430ES2.1 PANDA A1 version DTB: OMAP4-PANDA.DTB
>>>
>>> Booted with ramdisk and mmc FS
>>>
>>> commit c04efed734409f5a44715b54a6ca1b54b0ccf215
>>> Author: Stephen Rothwell <sfr@canb.auug.org.au>
>>> Date: Fri Jun 7 16:40:02 2013 +1000
>>>
>>> Add linux-next specific files for 20130607
>> Looks linux-next-20130607 is broken, see below:
>>
>> LD [M] drivers/usb/gadget/g_ncm.o
>> drivers/usb/musb/omap2430.c: In function 'omap2430_probe':
>> drivers/usb/musb/omap2430.c:571:2: error: 'musb_resources' undeclared
>> (first use in this function)
>> drivers/usb/musb/omap2430.c:571:2: note: each undeclared identifier is
>> reported only once for each function it appears in
>> drivers/usb/musb/omap2430.c:571:2: error: bit-field '<anonymous>'
>> width not an integer constant
>> drivers/usb/musb/omap2430.c:585:4: error: bit-field '<anonymous>'
>> width not an integer constant
>> make[3]: *** [drivers/usb/musb/omap2430.o] Error 1
>> make[3]: *** Waiting for unfinished jobs....
>> make[2]: *** [drivers/usb/musb] Error 2
>> make[2]: *** Waiting for unfinished jobs....
>> make[1]: *** [drivers/usb] Error 2
>> make: *** [drivers] Error 2
>> install kernel and modules
>>
>> DEPMOD 3.10.0-rc4-next-20130607+
> Even I disable musb so that kernel building is OK, but the kernel with dtb
> still can't boot, see attachment 'dmesg' and config.
>
>
> Thanks,
I am not sure how both of us are different. I was testing 20130607 with
an omap2plusdefconfig. Also i was using a minimal busy box file system..
Is there anything specific FS that you want me to try ?
I am using the latest u-boot version.
U-Boot SPL 2013.07-rc1-00010-gdfdb3d3 (Jun 17 2013 - 13:09:51)
OMAP4430 ES2.1
OMAP SD/MMC: 0
reading u-boot.img
reading u-boot.img
U-Boot 2013.07-rc1-00010-gdfdb3d3 (Jun 17 2013 - 13:09:51)
CPU : OMAP4430 ES2.1
Board: OMAP4 Panda
I2C: ready
DRAM: 1 GiB
MMC: OMAP SD/MMC: 0
Using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
Panda #
Panda # setenv bootargs root=/dev/ram0 rw console=ttyO2,115200n8 initrd=0x81600000,20M ramdisk_size=20480 earlyprintk
Panda # mmc dev 0
mmc0 is current device
Panda # fatload mmc 0 0x80300000 uImage
reading uImage
4394007 bytes read in 300 ms (14 MiB/s)
Panda # fatload mmc 0 0x81600000 bb.raw
reading bb.raw
10240000 bytes read in 722 ms (13.5 MiB/s)
Panda # bootm 0x80300000
## Booting kernel from Legacy Image at 80300000 ...
Image Name: Linux
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4393943 Bytes = 4.2 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.10.0-rc4-next-20130607 (a0393807@uda0393807) (gcc version 4.6.3 (Sourcery CodeBench Lite 2012.03-57) ) #18 SMP Mon Jun 17 12:55:05 IST 2013
[ 0.000000] CPU: ARMv7 Processor [411fc092] revision 2 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: OMAP4 Panda board
[ 0.000000] cma: CMA: reserved 16 MiB at ae800000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] OMAP4430 ES2.1
[ 0.000000] PERCPU: Embedded 9 pages/cpu @c15d5000 s13440 r8192 d15232 u36864
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260368
[ 0.000000] Kernel command line: root=/dev/ram0 rw console=ttyO2,115200n8 initrd=0x81600000,20M ramdisk_size=20480 earlyprintk
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 987436K/1047552K available (5619K kernel code, 603K rwdata, 1908K rodata, 393K init, 5521K bss, 60116K reserved, 269312K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc07620e8 (7529 kB)
[ 0.000000] .init : 0xc0763000 - 0xc07c5480 ( 394 kB)
[ 0.000000] .data : 0xc07c6000 - 0xc085ccc8 ( 604 kB)
[ 0.000000] .bss : 0xc085ccc8 - 0xc0dc10f0 (5522 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] OMAP clockevent source: timer1 at 32768 Hz
[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
[ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.000000] ... MAX_LOCK_DEPTH: 48
[ 0.000000] ... MAX_LOCKDEP_KEYS: 8191
[ 0.000000] ... CLASSHASH_SIZE: 4096
[ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384
[ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768
[ 0.000000] ... CHAINHASH_SIZE: 16384
[ 0.000000] memory used by lock dependency info: 3695 kB
[ 0.000000] per task-struct memory footprint: 1152 bytes
[ 0.001403] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 0.079742] pid_max: default: 32768 minimum: 301
[ 0.080535] Security Framework initialized
[ 0.080780] Mount-cache hash table entries: 512
[ 0.085571] CPU: Testing write buffer coherency: ok
[ 0.087493] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.087829] Setting up static identity map for 0xc0556058 - 0xc05560c8
[ 0.087890] L310 cache controller enabled
[ 0.087921] l2x0: 16 ways, CACHE_ID 0x410000c4, AUX_CTRL 0x7e470000, Cache size: 1048576 B
[ 0.093048] CPU1: Booted secondary processor
[ 0.177764] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.178283] Brought up 2 CPUs
[ 0.178314] SMP: Total of 2 processors activated (2387.96 BogoMIPS).
[ 0.178314] CPU: All CPU(s) started in SVC mode.
[ 0.181152] devtmpfs: initialized
[ 0.254455] pinctrl core: initialized pinctrl subsystem
[ 0.258117] regulator-dummy: no parameters
[ 0.261657] NET: Registered protocol family 16
[ 0.270538] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.272033] omap-gpmc omap-gpmc: GPMC revision 6.0
[ 0.281036] OMAP GPIO hardware version 0.1
[ 0.295837] omap_mux_init: Add partition: #1: core, flags: 3
[ 0.298095] omap_mux_init: Add partition: #2: wkup, flags: 3
[ 0.298309] error setting wl12xx data: -38
[ 0.298583] omap_mux_get_by_name: Could not find signal sys_nirq
[ 0.303375] omap_mux_get_by_name: Could not find signal uart1_rx.uart1_rx
[ 0.384521] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.384521] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.398803] OMAP DMA hardware revision 0.0
[ 0.402832] ARM PMU: not yet supported on OMAP4430 due to missing CTI driver
[ 0.449371] bio: create slab <bio-0> at 0
[ 0.514038] omap-dma-engine omap-dma-engine: OMAP DMA engine driver
[ 0.515258] vwl1271: 1800 mV
[ 0.516174] hsusb1_reset: 3300 mV
[ 0.516967] hsusb1_vcc: 3300 mV
[ 0.522064] SCSI subsystem initialized
[ 0.523773] usbcore: registered new interface driver usbfs
[ 0.524139] usbcore: registered new interface driver hub
[ 0.524658] usbcore: registered new device driver usb
[ 0.528869] omap_i2c omap_i2c.1: bus 1 rev0.10 at 400 kHz
[ 0.529907] omap_i2c omap_i2c.2: bus 2 rev0.10 at 400 kHz
[ 0.531280] omap_i2c omap_i2c.3: bus 3 rev0.10 at 100 kHz
[ 0.532226] omap_i2c omap_i2c.4: bus 4 rev0.10 at 400 kHz
[ 0.538391] Switching to clocksource 32k_counter
[ 0.655364] NET: Registered protocol family 2
[ 0.657409] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.657806] TCP bind hash table entries: 8192 (order: 6, 294912 bytes)
[ 0.660980] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.661315] TCP: reno registered
[ 0.661346] UDP hash table entries: 512 (order: 3, 40960 bytes)
[ 0.661773] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes)
[ 0.663421] NET: Registered protocol family 1
[ 0.664733] RPC: Registered named UNIX socket transport module.
[ 0.664764] RPC: Registered udp transport module.
[ 0.664764] RPC: Registered tcp transport module.
[ 0.664764] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.665740] Trying to unpack rootfs image as initramfs...
[ 0.666931] rootfs image is not initramfs (junk in compressed archive); looks like an initrd
[ 0.819061] Freeing initrd memory: 20480K (c1600000 - c2a00000)
[ 0.819183] NetWinder Floating Point Emulator V0.97 (double precision)
[ 1.007995] bounce pool size: 64 pages
[ 1.008575] VFS: Disk quotas dquot_6.5.2
[ 1.009033] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.011779] NFS: Registering the id_resolver key type
[ 1.012207] Key type id_resolver registered
[ 1.012237] Key type id_legacy registered
[ 1.012390] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 1.013031] msgmni has been set to 1474
[ 1.016387] io scheduler noop registered
[ 1.016418] io scheduler deadline registered
[ 1.016510] io scheduler cfq registered (default)
[ 1.020660] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.027069] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 104) is a OMAP UART0
[ 1.029296] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 105) is a OMAP UART1
[ 1.030670] omap_uart.2: ttyO2 at MMIO 0x48020000 (irq = 106) is a OMAP UART2
[ 1.724426] console [ttyO2] enabled
[ 1.729583] omap_uart.3: ttyO3 at MMIO 0x4806e000 (irq = 102) is a OMAP UART3
[ 1.765686] brd: module loaded
[ 1.784973] loop: module loaded
[ 1.791503] Skipping twl internal clock init and using bootloader value (unknown osc rate)
[ 1.802978] twl 1-0048: PIH (irq 39) chaining IRQs 418..438
[ 1.811218] VUSB: 3300 mV normal standby
[ 1.816864] vdd_mpu: 500 <--> 1500 mV normal
[ 1.823730] vdd_iva: 500 <--> 1500 mV normal
[ 1.829803] vdd_core: 500 <--> 1500 mV normal
[ 1.836334] V1V8: 1800 mV normal standby
[ 1.841979] V2V1: 2100 mV normal standby
[ 1.847717] VMMC: 1200 <--> 3000 mV at 3000 mV normal standby
[ 1.855773] VPP: 1800 <--> 2500 mV at 1900 mV normal standby
[ 1.864196] VCXIO: 1800 mV normal standby
[ 1.868499] VCXIO: supplied by V2V1
[ 1.875030] VDAC: 1800 mV normal standby
[ 1.879333] VDAC: supplied by V2V1
[ 1.885223] VAUX2_6030: 1200 <--> 2800 mV at 1800 mV normal standby
[ 1.893768] VAUX3_6030: 1000 <--> 3000 mV at 1200 mV normal standby
[ 1.903076] VANA: 2100 mV normal standby
[ 1.917877] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 1.934997] usbcore: registered new interface driver asix
[ 1.941284] usbcore: registered new interface driver ax88179_178a
[ 1.948089] usbcore: registered new interface driver cdc_ether
[ 1.954681] usbcore: registered new interface driver smsc95xx
[ 1.961242] usbcore: registered new interface driver net1080
[ 1.967559] usbcore: registered new interface driver cdc_subset
[ 1.974243] usbcore: registered new interface driver zaurus
[ 1.980621] usbcore: registered new interface driver cdc_ncm
[ 1.988220] usbcore: registered new interface driver cdc_wdm
[ 1.994659] usbcore: registered new interface driver usb-storage
[ 2.001464] usbcore: registered new interface driver usbtest
[ 2.009277] mousedev: PS/2 mouse device common for all mice
[ 2.020721] twl_rtc twl_rtc: Enabling TWL-RTC
[ 2.030181] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
[ 2.059692] i2c /dev entries driver
[ 2.067108] Driver for 1-wire Dallas network protocol.
[ 2.076293] omap_wdt: OMAP Watchdog Timer Rev 0x00: initial timeout 60 sec
[ 2.086364] omap-dma-engine omap-dma-engine: allocating channel for 62
[ 2.093414] omap-dma-engine omap-dma-engine: allocating channel for 61
[ 2.139251] omap-dma-engine omap-dma-engine: allocating channel for 60
[ 2.146209] omap-dma-engine omap-dma-engine: allocating channel for 59
[ 2.262664] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.270233] usbcore: registered new interface driver usbhid
[ 2.276153] usbhid: USB HID core driver
[ 2.281402] oprofile: no performance counters
[ 2.288024] oprofile: using timer interrupt.
[ 2.293334] TCP: cubic registered
[ 2.296844] Initializing XFRM netlink socket
[ 2.301544] NET: Registered protocol family 17
[ 2.306365] NET: Registered protocol family 15
[ 2.311614] Key type dns_resolver registered
[ 2.316284] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 1
[ 2.334320] Power Management for TI OMAP4.
[ 2.338684] OMAP4 PM: u-boot >= v2012.07 is required for full PM support
[ 2.346069] ThumbEE CPU extension supported.
[ 2.354187] VANA: incomplete constraints, leaving on
[ 2.361175] VDAC: incomplete constraints, leaving on
[ 2.367614] VUSB: incomplete constraints, leaving on
[ 2.377258] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:03:17 UTC (946684997)
[ 2.388793] RAMDISK: ext2 filesystem found at block 0
[ 2.395324] RAMDISK: Loading 10000KiB [1 disk] into ram disk... [ 2.410461] mmc0: host does not support reading read-only switch. assuming write-enable.
[ 2.424896] mmc0: new high speed SD card at address 0002
[ 2.436248] mmcblk0: mmc0:0002 00000 1.86 GiB
[ 2.455200] mmcblk0: p1 p2
done.
[ 2.858886] EXT2-fs (ram0): warning: mounting unchecked fs, running e2fsck is recommended
[ 2.858886] VFS: Mounted root (ext2 filesystem) on device 1:0.
[ 2.874725] devtmpfs: mounted
[ 2.879028] Freeing unused kernel memory: 392K (c0763000 - c07c5000)
Mounting proc : OK
Mounting sysfs : OK
Mounting /dev : OK
Creating local mdev devices
umount: can't umount /mnt/mmc: Invalid argument
******************************************
Starting System Init for 6430EVM-6430
Release: OpnSrc
******************************************
Saving kernel ring buffer : OK
Mounting devpts : OK
Setting up networking
Configuring lo : OK
Configuring eth0 : ifconfig: eth0: error fetching interface information: Device not found
ifup: can't open '/etc/network/interfaces': No such file or directory
Failed
Starting syslogd : OK
Starting klogd : OK
Mounting filesystems : mount: according to /proc/mounts, none is already mounted on /dev/pts
mount: according to /proc/mounts, /proc is already mounted on /proc
OK
Please press Enter to activate this console.
#
Regards,
Sricharan
WARNING: multiple messages have this Message-ID (diff)
From: r.sricharan@ti.com (Sricharan R)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 2/6] ARM: OMAP2+: Remove board-omap4panda.c
Date: Mon, 17 Jun 2013 13:12:05 +0530 [thread overview]
Message-ID: <51BEBDCD.3060104@ti.com> (raw)
In-Reply-To: <CACVXFVNzAMrkhrAMAmQ7ZdJdby2O4VdoD8BVHRF-O=rPKQMqbw@mail.gmail.com>
On Friday 14 June 2013 07:28 PM, Ming Lei wrote:
> On Fri, Jun 14, 2013 at 9:31 PM, Ming Lei <tom.leiming@gmail.com> wrote:
>> On Thu, Jun 13, 2013 at 6:12 PM, Sricharan R <r.sricharan@ti.com> wrote:
>>> On Thursday 13 June 2013 02:51 PM, Sricharan R wrote:
>>>> Hi Tony,
>>>> On Wednesday 12 June 2013 10:44 PM, Tony Lindgren wrote:
>>>>> * Tony Lindgren <tony@atomide.com> [130612 09:37]:
>>>>>> * Ming Lei <tom.leiming@gmail.com> [130603 08:34]:
>>>>>>> Hi,
>>>>>>>
>>>>>>> On Sat, May 18, 2013 at 3:17 AM, Tony Lindgren <tony@atomide.com> wrote:
>>>>>>>> We can now boot with device tree. If you don't want to update u-boot,
>>>>>>>> you can boot with appended DTB with the following instructions:
>>>>>>>>
>>>>>>>> 1. Make sure you have the appended DTB support in .config
>>>>>>>>
>>>>>>>> CONFIG_ARM_APPENDED_DTB=y
>>>>>>>> CONFIG_ARM_ATAG_DTB_COMPAT=y
>>>>>>>> CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND=y
>>>>>>>>
>>>>>>>> 2. Build the zImage
>>>>>>>>
>>>>>>>> $ ARCH=arm CROSS_COMPILE=... make zImage
>>>>>>>>
>>>>>>>> 3. Build the device tree blobs
>>>>>>>>
>>>>>>>> $ ARCH=arm CROSS_COMPILE=... make dtbs
>>>>>>>>
>>>>>>>> 4. Append the correct panda dtb to zImage
>>>>>>>>
>>>>>>>> Depending on your hardware it's omap4-panda.dtb, omap4-panda-a4.dtb
>>>>>>>> or omap4-panda-es.dtb.
>>>>>>>>
>>>>>>>> $ cat arch/arm/boot/zImage arch/arm/boot/dts/omap4-panda-es.dtb > /tmp/appended
>>>>>>>>
>>>>>>>> 5. Use mkimage to produce the appended device tree uImage
>>>>>>>>
>>>>>>>> $ mkimage -A arm -O linux -T kernel -C none -a 0x80008000 -e 0x80008000 \
>>>>>>>> -n "Linux" -d /tmp/appended /tmp/uImage
>>>>>>> I followed the above steps and tried devicetree on Pandaboard against
>>>>>>> 3.10.0-rc3-next-20130528, and the board will hang during boot, but works
>>>>>>> well with legacy mode.
>>>>>>>
>>>>>>> Hardware: Pandaboard A1
>>>>>>> dtb: omap4-panda.dtb
>>>>>>>
>>>>>>> See 'dmesg' on below link:
>>>>>>>
>>>>>>> http://kernel.ubuntu.com/~ming/up/panda-dts.dmesg
>>>>>>>
>>>>>> Hmm looks like it boots to init. Maybe add initcall_debug to the cmdline in
>>>>>> case there's some late_initcall that causes the issue. It's probably some
>>>>>> trivial issue causing it.
>>>>> Sricharan, maybe give this a quick try if you have the original pandaboard?
>>>>> I only have pandaboard es.
>>>>>
>>>>> Regards,
>>>>>
>>>>> Tony
>>>> I tried your cleanup branch omap-for-v3.11/cleanup on panda board and it booted
>>>> to prompt fine.
>>>> Hardware: Pandaboard A1 dtb: omap4-panda.dtb
>>>>
>>>> git pull on linux-next branch was not working though.
>>>>
>>> Ok, tested in linux-next as well and it booted fine with DTB.
>>> HW: OMAP4430ES2.1 PANDA A1 version DTB: OMAP4-PANDA.DTB
>>>
>>> Booted with ramdisk and mmc FS
>>>
>>> commit c04efed734409f5a44715b54a6ca1b54b0ccf215
>>> Author: Stephen Rothwell <sfr@canb.auug.org.au>
>>> Date: Fri Jun 7 16:40:02 2013 +1000
>>>
>>> Add linux-next specific files for 20130607
>> Looks linux-next-20130607 is broken, see below:
>>
>> LD [M] drivers/usb/gadget/g_ncm.o
>> drivers/usb/musb/omap2430.c: In function 'omap2430_probe':
>> drivers/usb/musb/omap2430.c:571:2: error: 'musb_resources' undeclared
>> (first use in this function)
>> drivers/usb/musb/omap2430.c:571:2: note: each undeclared identifier is
>> reported only once for each function it appears in
>> drivers/usb/musb/omap2430.c:571:2: error: bit-field '<anonymous>'
>> width not an integer constant
>> drivers/usb/musb/omap2430.c:585:4: error: bit-field '<anonymous>'
>> width not an integer constant
>> make[3]: *** [drivers/usb/musb/omap2430.o] Error 1
>> make[3]: *** Waiting for unfinished jobs....
>> make[2]: *** [drivers/usb/musb] Error 2
>> make[2]: *** Waiting for unfinished jobs....
>> make[1]: *** [drivers/usb] Error 2
>> make: *** [drivers] Error 2
>> install kernel and modules
>>
>> DEPMOD 3.10.0-rc4-next-20130607+
> Even I disable musb so that kernel building is OK, but the kernel with dtb
> still can't boot, see attachment 'dmesg' and config.
>
>
> Thanks,
I am not sure how both of us are different. I was testing 20130607 with
an omap2plusdefconfig. Also i was using a minimal busy box file system..
Is there anything specific FS that you want me to try ?
I am using the latest u-boot version.
U-Boot SPL 2013.07-rc1-00010-gdfdb3d3 (Jun 17 2013 - 13:09:51)
OMAP4430 ES2.1
OMAP SD/MMC: 0
reading u-boot.img
reading u-boot.img
U-Boot 2013.07-rc1-00010-gdfdb3d3 (Jun 17 2013 - 13:09:51)
CPU : OMAP4430 ES2.1
Board: OMAP4 Panda
I2C: ready
DRAM: 1 GiB
MMC: OMAP SD/MMC: 0
Using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
Panda #
Panda # setenv bootargs root=/dev/ram0 rw console=ttyO2,115200n8 initrd=0x81600000,20M ramdisk_size=20480 earlyprintk
Panda # mmc dev 0
mmc0 is current device
Panda # fatload mmc 0 0x80300000 uImage
reading uImage
4394007 bytes read in 300 ms (14 MiB/s)
Panda # fatload mmc 0 0x81600000 bb.raw
reading bb.raw
10240000 bytes read in 722 ms (13.5 MiB/s)
Panda # bootm 0x80300000
## Booting kernel from Legacy Image at 80300000 ...
Image Name: Linux
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4393943 Bytes = 4.2 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.10.0-rc4-next-20130607 (a0393807 at uda0393807) (gcc version 4.6.3 (Sourcery CodeBench Lite 2012.03-57) ) #18 SMP Mon Jun 17 12:55:05 IST 2013
[ 0.000000] CPU: ARMv7 Processor [411fc092] revision 2 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: OMAP4 Panda board
[ 0.000000] cma: CMA: reserved 16 MiB at ae800000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] OMAP4430 ES2.1
[ 0.000000] PERCPU: Embedded 9 pages/cpu @c15d5000 s13440 r8192 d15232 u36864
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260368
[ 0.000000] Kernel command line: root=/dev/ram0 rw console=ttyO2,115200n8 initrd=0x81600000,20M ramdisk_size=20480 earlyprintk
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 987436K/1047552K available (5619K kernel code, 603K rwdata, 1908K rodata, 393K init, 5521K bss, 60116K reserved, 269312K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc07620e8 (7529 kB)
[ 0.000000] .init : 0xc0763000 - 0xc07c5480 ( 394 kB)
[ 0.000000] .data : 0xc07c6000 - 0xc085ccc8 ( 604 kB)
[ 0.000000] .bss : 0xc085ccc8 - 0xc0dc10f0 (5522 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] OMAP clockevent source: timer1 at 32768 Hz
[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
[ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.000000] ... MAX_LOCK_DEPTH: 48
[ 0.000000] ... MAX_LOCKDEP_KEYS: 8191
[ 0.000000] ... CLASSHASH_SIZE: 4096
[ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384
[ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768
[ 0.000000] ... CHAINHASH_SIZE: 16384
[ 0.000000] memory used by lock dependency info: 3695 kB
[ 0.000000] per task-struct memory footprint: 1152 bytes
[ 0.001403] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 0.079742] pid_max: default: 32768 minimum: 301
[ 0.080535] Security Framework initialized
[ 0.080780] Mount-cache hash table entries: 512
[ 0.085571] CPU: Testing write buffer coherency: ok
[ 0.087493] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.087829] Setting up static identity map for 0xc0556058 - 0xc05560c8
[ 0.087890] L310 cache controller enabled
[ 0.087921] l2x0: 16 ways, CACHE_ID 0x410000c4, AUX_CTRL 0x7e470000, Cache size: 1048576 B
[ 0.093048] CPU1: Booted secondary processor
[ 0.177764] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.178283] Brought up 2 CPUs
[ 0.178314] SMP: Total of 2 processors activated (2387.96 BogoMIPS).
[ 0.178314] CPU: All CPU(s) started in SVC mode.
[ 0.181152] devtmpfs: initialized
[ 0.254455] pinctrl core: initialized pinctrl subsystem
[ 0.258117] regulator-dummy: no parameters
[ 0.261657] NET: Registered protocol family 16
[ 0.270538] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.272033] omap-gpmc omap-gpmc: GPMC revision 6.0
[ 0.281036] OMAP GPIO hardware version 0.1
[ 0.295837] omap_mux_init: Add partition: #1: core, flags: 3
[ 0.298095] omap_mux_init: Add partition: #2: wkup, flags: 3
[ 0.298309] error setting wl12xx data: -38
[ 0.298583] omap_mux_get_by_name: Could not find signal sys_nirq
[ 0.303375] omap_mux_get_by_name: Could not find signal uart1_rx.uart1_rx
[ 0.384521] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.384521] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.398803] OMAP DMA hardware revision 0.0
[ 0.402832] ARM PMU: not yet supported on OMAP4430 due to missing CTI driver
[ 0.449371] bio: create slab <bio-0> at 0
[ 0.514038] omap-dma-engine omap-dma-engine: OMAP DMA engine driver
[ 0.515258] vwl1271: 1800 mV
[ 0.516174] hsusb1_reset: 3300 mV
[ 0.516967] hsusb1_vcc: 3300 mV
[ 0.522064] SCSI subsystem initialized
[ 0.523773] usbcore: registered new interface driver usbfs
[ 0.524139] usbcore: registered new interface driver hub
[ 0.524658] usbcore: registered new device driver usb
[ 0.528869] omap_i2c omap_i2c.1: bus 1 rev0.10 at 400 kHz
[ 0.529907] omap_i2c omap_i2c.2: bus 2 rev0.10 at 400 kHz
[ 0.531280] omap_i2c omap_i2c.3: bus 3 rev0.10 at 100 kHz
[ 0.532226] omap_i2c omap_i2c.4: bus 4 rev0.10 at 400 kHz
[ 0.538391] Switching to clocksource 32k_counter
[ 0.655364] NET: Registered protocol family 2
[ 0.657409] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.657806] TCP bind hash table entries: 8192 (order: 6, 294912 bytes)
[ 0.660980] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.661315] TCP: reno registered
[ 0.661346] UDP hash table entries: 512 (order: 3, 40960 bytes)
[ 0.661773] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes)
[ 0.663421] NET: Registered protocol family 1
[ 0.664733] RPC: Registered named UNIX socket transport module.
[ 0.664764] RPC: Registered udp transport module.
[ 0.664764] RPC: Registered tcp transport module.
[ 0.664764] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.665740] Trying to unpack rootfs image as initramfs...
[ 0.666931] rootfs image is not initramfs (junk in compressed archive); looks like an initrd
[ 0.819061] Freeing initrd memory: 20480K (c1600000 - c2a00000)
[ 0.819183] NetWinder Floating Point Emulator V0.97 (double precision)
[ 1.007995] bounce pool size: 64 pages
[ 1.008575] VFS: Disk quotas dquot_6.5.2
[ 1.009033] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.011779] NFS: Registering the id_resolver key type
[ 1.012207] Key type id_resolver registered
[ 1.012237] Key type id_legacy registered
[ 1.012390] jffs2: version 2.2. (NAND) (SUMMARY) ? 2001-2006 Red Hat, Inc.
[ 1.013031] msgmni has been set to 1474
[ 1.016387] io scheduler noop registered
[ 1.016418] io scheduler deadline registered
[ 1.016510] io scheduler cfq registered (default)
[ 1.020660] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.027069] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 104) is a OMAP UART0
[ 1.029296] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 105) is a OMAP UART1
[ 1.030670] omap_uart.2: ttyO2 at MMIO 0x48020000 (irq = 106) is a OMAP UART2
[ 1.724426] console [ttyO2] enabled
[ 1.729583] omap_uart.3: ttyO3 at MMIO 0x4806e000 (irq = 102) is a OMAP UART3
[ 1.765686] brd: module loaded
[ 1.784973] loop: module loaded
[ 1.791503] Skipping twl internal clock init and using bootloader value (unknown osc rate)
[ 1.802978] twl 1-0048: PIH (irq 39) chaining IRQs 418..438
[ 1.811218] VUSB: 3300 mV normal standby
[ 1.816864] vdd_mpu: 500 <--> 1500 mV normal
[ 1.823730] vdd_iva: 500 <--> 1500 mV normal
[ 1.829803] vdd_core: 500 <--> 1500 mV normal
[ 1.836334] V1V8: 1800 mV normal standby
[ 1.841979] V2V1: 2100 mV normal standby
[ 1.847717] VMMC: 1200 <--> 3000 mV at 3000 mV normal standby
[ 1.855773] VPP: 1800 <--> 2500 mV at 1900 mV normal standby
[ 1.864196] VCXIO: 1800 mV normal standby
[ 1.868499] VCXIO: supplied by V2V1
[ 1.875030] VDAC: 1800 mV normal standby
[ 1.879333] VDAC: supplied by V2V1
[ 1.885223] VAUX2_6030: 1200 <--> 2800 mV at 1800 mV normal standby
[ 1.893768] VAUX3_6030: 1000 <--> 3000 mV at 1200 mV normal standby
[ 1.903076] VANA: 2100 mV normal standby
[ 1.917877] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 1.934997] usbcore: registered new interface driver asix
[ 1.941284] usbcore: registered new interface driver ax88179_178a
[ 1.948089] usbcore: registered new interface driver cdc_ether
[ 1.954681] usbcore: registered new interface driver smsc95xx
[ 1.961242] usbcore: registered new interface driver net1080
[ 1.967559] usbcore: registered new interface driver cdc_subset
[ 1.974243] usbcore: registered new interface driver zaurus
[ 1.980621] usbcore: registered new interface driver cdc_ncm
[ 1.988220] usbcore: registered new interface driver cdc_wdm
[ 1.994659] usbcore: registered new interface driver usb-storage
[ 2.001464] usbcore: registered new interface driver usbtest
[ 2.009277] mousedev: PS/2 mouse device common for all mice
[ 2.020721] twl_rtc twl_rtc: Enabling TWL-RTC
[ 2.030181] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
[ 2.059692] i2c /dev entries driver
[ 2.067108] Driver for 1-wire Dallas network protocol.
[ 2.076293] omap_wdt: OMAP Watchdog Timer Rev 0x00: initial timeout 60 sec
[ 2.086364] omap-dma-engine omap-dma-engine: allocating channel for 62
[ 2.093414] omap-dma-engine omap-dma-engine: allocating channel for 61
[ 2.139251] omap-dma-engine omap-dma-engine: allocating channel for 60
[ 2.146209] omap-dma-engine omap-dma-engine: allocating channel for 59
[ 2.262664] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.270233] usbcore: registered new interface driver usbhid
[ 2.276153] usbhid: USB HID core driver
[ 2.281402] oprofile: no performance counters
[ 2.288024] oprofile: using timer interrupt.
[ 2.293334] TCP: cubic registered
[ 2.296844] Initializing XFRM netlink socket
[ 2.301544] NET: Registered protocol family 17
[ 2.306365] NET: Registered protocol family 15
[ 2.311614] Key type dns_resolver registered
[ 2.316284] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 1
[ 2.334320] Power Management for TI OMAP4.
[ 2.338684] OMAP4 PM: u-boot >= v2012.07 is required for full PM support
[ 2.346069] ThumbEE CPU extension supported.
[ 2.354187] VANA: incomplete constraints, leaving on
[ 2.361175] VDAC: incomplete constraints, leaving on
[ 2.367614] VUSB: incomplete constraints, leaving on
[ 2.377258] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:03:17 UTC (946684997)
[ 2.388793] RAMDISK: ext2 filesystem found at block 0
[ 2.395324] RAMDISK: Loading 10000KiB [1 disk] into ram disk... [ 2.410461] mmc0: host does not support reading read-only switch. assuming write-enable.
[ 2.424896] mmc0: new high speed SD card at address 0002
[ 2.436248] mmcblk0: mmc0:0002 00000 1.86 GiB
[ 2.455200] mmcblk0: p1 p2
done.
[ 2.858886] EXT2-fs (ram0): warning: mounting unchecked fs, running e2fsck is recommended
[ 2.858886] VFS: Mounted root (ext2 filesystem) on device 1:0.
[ 2.874725] devtmpfs: mounted
[ 2.879028] Freeing unused kernel memory: 392K (c0763000 - c07c5000)
Mounting proc : OK
Mounting sysfs : OK
Mounting /dev : OK
Creating local mdev devices
umount: can't umount /mnt/mmc: Invalid argument
******************************************
Starting System Init for 6430EVM-6430
Release: OpnSrc
******************************************
Saving kernel ring buffer : OK
Mounting devpts : OK
Setting up networking
Configuring lo : OK
Configuring eth0 : ifconfig: eth0: error fetching interface information: Device not found
ifup: can't open '/etc/network/interfaces': No such file or directory
Failed
Starting syslogd : OK
Starting klogd : OK
Mounting filesystems : mount: according to /proc/mounts, none is already mounted on /dev/pts
mount: according to /proc/mounts, /proc is already mounted on /proc
OK
Please press Enter to activate this console.
#
Regards,
Sricharan
next prev parent reply other threads:[~2013-06-17 7:42 UTC|newest]
Thread overview: 100+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-05-17 19:17 [PATCH 0/6] Drop legacy booting for omap4 for v3.11, boot with device tree only Tony Lindgren
2013-05-17 19:17 ` Tony Lindgren
2013-05-17 19:17 ` [PATCH 1/6] ARM: OMAP2+: Remove board-4430sdp.c Tony Lindgren
2013-05-17 19:17 ` Tony Lindgren
2013-05-20 9:54 ` Russell King - ARM Linux
2013-05-20 9:54 ` Russell King - ARM Linux
2013-05-20 17:10 ` Tony Lindgren
2013-05-20 17:10 ` Tony Lindgren
2013-07-06 13:10 ` Russell King - ARM Linux
2013-07-06 13:10 ` Russell King - ARM Linux
2013-07-06 13:36 ` Russell King - ARM Linux
2013-07-06 13:36 ` Russell King - ARM Linux
2013-07-08 9:34 ` Tony Lindgren
2013-07-08 9:34 ` Tony Lindgren
2013-07-08 14:21 ` Russell King - ARM Linux
2013-07-08 14:21 ` Russell King - ARM Linux
2013-07-09 8:23 ` Tony Lindgren
2013-07-09 8:23 ` Tony Lindgren
2013-07-12 9:09 ` Peter Ujfalusi
2013-07-12 9:09 ` Peter Ujfalusi
2013-07-22 9:40 ` Tomi Valkeinen
2013-07-22 9:40 ` Tomi Valkeinen
2013-10-27 13:26 ` Javier Martinez Canillas
2013-10-27 13:26 ` Javier Martinez Canillas
2013-10-28 13:32 ` Tomi Valkeinen
2013-10-28 13:32 ` Tomi Valkeinen
2013-10-28 14:25 ` Javier Martinez Canillas
2013-10-28 14:25 ` Javier Martinez Canillas
2013-07-13 2:31 ` Olof Johansson
2013-07-13 2:31 ` Olof Johansson
2013-07-13 3:10 ` Olof Johansson
2013-07-13 3:10 ` Olof Johansson
2013-07-15 6:55 ` Tony Lindgren
2013-07-15 6:55 ` Tony Lindgren
2013-07-06 21:36 ` Arnd Bergmann
2013-07-06 21:36 ` Arnd Bergmann
2013-07-06 23:37 ` debugging options (was: Re: [PATCH 1/6] ARM: OMAP2+: Remove board-4430sdp.c) Russell King - ARM Linux
2013-07-06 23:37 ` Russell King - ARM Linux
2013-05-17 19:17 ` [PATCH 2/6] ARM: OMAP2+: Remove board-omap4panda.c Tony Lindgren
2013-05-17 19:17 ` Tony Lindgren
2013-06-03 15:28 ` Ming Lei
2013-06-03 15:28 ` Ming Lei
2013-06-12 16:31 ` Tony Lindgren
2013-06-12 16:31 ` Tony Lindgren
2013-06-12 17:14 ` Tony Lindgren
2013-06-12 17:14 ` Tony Lindgren
2013-06-13 9:21 ` Sricharan R
2013-06-13 9:21 ` Sricharan R
2013-06-13 10:12 ` Sricharan R
2013-06-13 10:12 ` Sricharan R
2013-06-13 11:05 ` Tony Lindgren
2013-06-13 11:05 ` Tony Lindgren
2013-06-13 13:36 ` Ming Lei
2013-06-13 13:36 ` Ming Lei
2013-06-14 13:31 ` Ming Lei
2013-06-14 13:31 ` Ming Lei
2013-06-14 13:58 ` Ming Lei
2013-06-14 13:58 ` Ming Lei
2013-06-17 7:42 ` Sricharan R [this message]
2013-06-17 7:42 ` Sricharan R
2013-06-17 8:06 ` Arnaud Patard
2013-06-17 8:06 ` Arnaud Patard (Rtp)
2013-06-17 8:16 ` Ming Lei
2013-06-17 8:16 ` Ming Lei
2013-06-17 8:27 ` Tony Lindgren
2013-06-17 8:27 ` Tony Lindgren
2013-06-17 8:41 ` Ming Lei
2013-06-17 8:41 ` Ming Lei
2013-06-17 8:49 ` Tony Lindgren
2013-06-17 8:49 ` Tony Lindgren
2013-06-17 8:24 ` Tony Lindgren
2013-06-17 8:24 ` Tony Lindgren
2013-06-17 9:46 ` Arnaud Patard
2013-06-17 9:46 ` Arnaud Patard (Rtp)
2013-06-17 10:26 ` Tony Lindgren
2013-06-17 10:26 ` Tony Lindgren
2013-06-18 11:27 ` Tony Lindgren
2013-06-18 11:27 ` Tony Lindgren
2013-06-19 9:45 ` Arnaud Patard
2013-06-19 9:45 ` Arnaud Patard (Rtp)
2013-06-19 9:58 ` Tony Lindgren
2013-06-19 9:58 ` Tony Lindgren
2013-06-20 7:29 ` Arnaud Patard
2013-06-20 7:29 ` Arnaud Patard (Rtp)
2013-06-21 6:01 ` Tony Lindgren
2013-06-21 6:01 ` Tony Lindgren
2013-05-17 19:17 ` [PATCH 3/6] ARM: OMAP2+: Remove legacy mux data for omap4 Tony Lindgren
2013-05-17 19:17 ` Tony Lindgren
2013-05-17 19:17 ` [PATCH 4/6] ARM: OMAP2+: Remove omap4 pdata from hsmmc.c Tony Lindgren
2013-05-17 19:17 ` Tony Lindgren
2013-05-17 19:18 ` [PATCH 5/6] ARM: OMAP2+: Remove omap4 pdata for USB Tony Lindgren
2013-05-17 19:18 ` Tony Lindgren
2013-05-17 19:18 ` [PATCH 6/6] ARM: OMAP2+: Remove omap4 ocp2scp pdata Tony Lindgren
2013-05-17 19:18 ` Tony Lindgren
2013-05-17 20:05 ` Felipe Balbi
2013-05-17 20:05 ` Felipe Balbi
2013-05-21 11:53 ` Kishon Vijay Abraham I
2013-05-21 11:53 ` Kishon Vijay Abraham I
2013-06-07 10:05 ` [PATCH 0/6] Drop legacy booting for omap4 for v3.11, boot with device tree only Tomi Valkeinen
2013-06-07 10:05 ` Tomi Valkeinen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=51BEBDCD.3060104@ti.com \
--to=r.sricharan@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-omap@vger.kernel.org \
--cc=tom.leiming@gmail.com \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.