* [RFC 2/2] Add support for Omnivision OV5647
2016-05-24 18:16 [RFC 0/2] Add support for OV5647 sensor roliveir
2016-05-24 18:16 ` [RFC 1/2] Add OV5647 device tree documentation roliveir
@ 2016-05-24 18:16 ` roliveir
1 sibling, 0 replies; 4+ messages in thread
From: roliveir @ 2016-05-24 18:16 UTC (permalink / raw)
To: linux-media, devicetree
Cc: mchehab, robh+dt, Ramiro.Oliveira, CARLOS.PALMINHA
Signed-off-by: roliveir <roliveir@synopsys.com>
---
MAINTAINERS | 7 +
drivers/media/i2c/Kconfig | 11 +
drivers/media/i2c/Makefile | 1 +
drivers/media/i2c/ov5647.c | 891 +++++++++++++++++++++++++++++++++++++++++++++
4 files changed, 910 insertions(+)
create mode 100644 drivers/media/i2c/ov5647.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 81d940b..06697fc 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -8106,6 +8106,13 @@ M: Harald Welte <laforge@gnumonks.org>
S: Maintained
F: drivers/char/pcmcia/cm4040_cs.*
+OMNIVISION OV5647 SENSOR DRIVER
+M: Ramiro Oliveira <roliveir@synopsys.com>
+L: linux-media@vger.kernel.org
+T: git git://linuxtv.org/media_tree.git
+S: Maintained
+F: drivers/media/i2c/ov5647.c
+
OMNIVISION OV7670 SENSOR DRIVER
M: Jonathan Corbet <corbet@lwn.net>
L: linux-media@vger.kernel.org
diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index 993dc50..1d4891b 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -500,6 +500,17 @@ config VIDEO_OV2659
To compile this driver as a module, choose M here: the
module will be called ov2659.
+config VIDEO_OV5647
+ tristate "OmniVision OV5647 sensor support"
+ depends on I2C && VIDEO_V4L2
+ depends on MEDIA_CAMERA_SUPPORT
+ ---help---
+ This is a Video4Linux2 sensor-level driver for the OmniVision
+ OV5647 camera.
+
+ To compile this driver as a module, choose M here: the
+ module will be called ov5647.
+
config VIDEO_OV7640
tristate "OmniVision OV7640 sensor support"
depends on I2C && VIDEO_V4L2
diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index 94f2c99..a732a0c 100644
--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -80,3 +80,4 @@ obj-$(CONFIG_VIDEO_IR_I2C) += ir-kbd-i2c.o
obj-$(CONFIG_VIDEO_ML86V7667) += ml86v7667.o
obj-$(CONFIG_VIDEO_OV2659) += ov2659.o
obj-$(CONFIG_VIDEO_TC358743) += tc358743.o
+obj-$(CONFIG_VIDEO_OV5647) += ov5647.o
diff --git a/drivers/media/i2c/ov5647.c b/drivers/media/i2c/ov5647.c
new file mode 100644
index 0000000..4c58339
--- /dev/null
+++ b/drivers/media/i2c/ov5647.c
@@ -0,0 +1,891 @@
+/*
+ * A V4L2 driver for OmniVision OV5647 cameras.
+ *
+ * Based on Samsung S5K6AAFX SXGA 1/6" 1.3M CMOS Image Sensor driver
+ * Copyright (C) 2011 Sylwester Nawrocki <s.nawrocki@samsung.com>
+ *
+ * Based on Omnivision OV7670 Camera Driver
+ * Copyright (C) 2006-7 Jonathan Corbet <corbet@lwn.net>
+ *
+ * Copyright (C) 2016, Synopsys, Inc.
+ *
+ */
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/delay.h>
+#include <linux/videodev2.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-mediabus.h>
+#include <media/v4l2-image-sizes.h>
+#include <media/v4l2-of.h>
+#include <linux/io.h>
+
+static bool debug;
+module_param(debug, bool, 0644);
+MODULE_PARM_DESC(debug, "Debug level (0-1)");
+
+/*
+ * The ov5647 sits on i2c with ID 0x6c
+ */
+#define OV5647_I2C_ADDR 0x6c
+#define SENSOR_NAME "ov5647"
+
+#define OV5647_REG_CHIPID_H 0x300A
+#define OV5647_REG_CHIPID_L 0x300B
+
+#define REG_TERM 0xfffe
+#define VAL_TERM 0xfe
+#define REG_DLY 0xffff
+
+/*define the voltage level of control signal*/
+#define CSI_STBY_ON 1
+#define CSI_STBY_OFF 0
+#define CSI_RST_ON 0
+#define CSI_RST_OFF 1
+#define CSI_PWR_ON 1
+#define CSI_PWR_OFF 0
+#define CSI_AF_PWR_ON 1
+#define CSI_AF_PWR_OFF 0
+
+
+#define OV5647_ROW_START 0x01
+#define OV5647_ROW_START_MIN 0
+#define OV5647_ROW_START_MAX 2004
+#define OV5647_ROW_START_DEF 54
+
+#define OV5647_COLUMN_START 0x02
+#define OV5647_COLUMN_START_MIN 0
+#define OV5647_COLUMN_START_MAX 2750
+#define OV5647_COLUMN_START_DEF 16
+
+#define OV5647_WINDOW_HEIGHT 0x03
+#define OV5647_WINDOW_HEIGHT_MIN 2
+#define OV5647_WINDOW_HEIGHT_MAX 2006
+#define OV5647_WINDOW_HEIGHT_DEF 1944
+
+#define OV5647_WINDOW_WIDTH 0x04
+#define OV5647_WINDOW_WIDTH_MIN 2
+#define OV5647_WINDOW_WIDTH_MAX 2752
+#define OV5647_WINDOW_WIDTH_DEF 2592
+
+enum power_seq_cmd {
+ CSI_SUBDEV_PWR_OFF = 0x00,
+ CSI_SUBDEV_PWR_ON = 0x01,
+};
+
+struct regval_list {
+ uint16_t addr;
+ uint8_t data;
+};
+
+struct cfg_array {
+ struct regval_list *regs;
+ int size;
+};
+
+struct sensor_win_size {
+ int width;
+ int height;
+ unsigned int hoffset;
+ unsigned int voffset;
+ unsigned int hts;
+ unsigned int vts;
+ unsigned int pclk;
+ unsigned int mipi_bps;
+ unsigned int fps_fixed;
+ unsigned int bin_factor;
+ unsigned int intg_min;
+ unsigned int intg_max;
+ void *regs;
+ int regs_size;
+ int (*set_size)(struct v4l2_subdev *subdev);
+};
+
+
+struct ov5647 {
+ struct device *dev;
+ struct v4l2_subdev subdev;
+ struct media_pad pad;
+ struct mutex lock;
+ struct v4l2_mbus_framefmt format;
+ struct sensor_format_struct *fmt;
+ unsigned int width;
+ unsigned int height;
+ unsigned int capture_mode;
+ int hue;
+ struct v4l2_fract tpf;
+ struct sensor_win_size *current_wins;
+};
+
+static inline struct ov5647 *to_state(struct v4l2_subdev *subdev)
+{
+ return container_of(subdev, struct ov5647, subdev);
+}
+
+static struct regval_list sensor_oe_disable_regs[] = {
+ {0x3000, 0x00},
+ {0x3001, 0x00},
+ {0x3002, 0x00},
+};
+
+static struct regval_list sensor_oe_enable_regs[] = {
+ {0x3000, 0x0f},
+ {0x3001, 0xff},
+ {0x3002, 0xe4},
+};
+
+static struct regval_list ov5647_640x480[] = {
+ {0x0100, 0x00},
+ {0x0103, 0x01},
+ {0x3034, 0x08},
+ {0x3035, 0x21},
+ {0x3036, 0x46},
+ {0x303c, 0x11},
+ {0x3106, 0xf5},
+ {0x3821, 0x07},
+ {0x3820, 0x41},
+ {0x3827, 0xec},
+ {0x370c, 0x0f},
+ {0x3612, 0x59},
+ {0x3618, 0x00},
+ {0x5000, 0x06},
+ {0x5001, 0x01},
+ {0x5002, 0x41},
+ {0x5003, 0x08},
+ {0x5a00, 0x08},
+ {0x3000, 0x00},
+ {0x3001, 0x00},
+ {0x3002, 0x00},
+ {0x3016, 0x08},
+ {0x3017, 0xe0},
+ {0x3018, 0x44},
+ {0x301c, 0xf8},
+ {0x301d, 0xf0},
+ {0x3a18, 0x00},
+ {0x3a19, 0xf8},
+ {0x3c01, 0x80},
+ {0x3b07, 0x0c},
+ {0x380c, 0x07},
+ {0x380d, 0x68},
+ {0x380e, 0x03},
+ {0x380f, 0xd8},
+ {0x3814, 0x31},
+ {0x3815, 0x31},
+ {0x3708, 0x64},
+ {0x3709, 0x52},
+ {0x3808, 0x02},
+ {0x3809, 0x80},
+ {0x380a, 0x01},
+ {0x380b, 0xE0},
+ {0x3801, 0x00},
+ {0x3802, 0x00},
+ {0x3803, 0x00},
+ {0x3804, 0x0a},
+ {0x3805, 0x3f},
+ {0x3806, 0x07},
+ {0x3807, 0xa1},
+ {0x3811, 0x08},
+ {0x3813, 0x02},
+ {0x3630, 0x2e},
+ {0x3632, 0xe2},
+ {0x3633, 0x23},
+ {0x3634, 0x44},
+ {0x3636, 0x06},
+ {0x3620, 0x64},
+ {0x3621, 0xe0},
+ {0x3600, 0x37},
+ {0x3704, 0xa0},
+ {0x3703, 0x5a},
+ {0x3715, 0x78},
+ {0x3717, 0x01},
+ {0x3731, 0x02},
+ {0x370b, 0x60},
+ {0x3705, 0x1a},
+ {0x3f05, 0x02},
+ {0x3f06, 0x10},
+ {0x3f01, 0x0a},
+ {0x3a08, 0x01},
+ {0x3a09, 0x27},
+ {0x3a0a, 0x00},
+ {0x3a0b, 0xf6},
+ {0x3a0d, 0x04},
+ {0x3a0e, 0x03},
+ {0x3a0f, 0x58},
+ {0x3a10, 0x50},
+ {0x3a1b, 0x58},
+ {0x3a1e, 0x50},
+ {0x3a11, 0x60},
+ {0x3a1f, 0x28},
+ {0x4001, 0x02},
+ {0x4004, 0x02},
+ {0x4000, 0x09},
+ {0x4837, 0x24},
+ {0x4050, 0x6e},
+ {0x4051, 0x8f},
+ {0x0100, 0x01},
+};
+
+struct sensor_format_struct;
+
+/**
+* @short I2C Write operation
+* @param[in] i2c_client I2C client
+* @param[in] reg register address
+* @param[in] val value to write
+* @return Error code
+*/
+static int ov5647_write(struct v4l2_subdev *sd, uint16_t reg, uint8_t val)
+{
+ int ret;
+ unsigned char data[3] = { reg >> 8, reg & 0xff, val};
+ struct i2c_client *client = v4l2_get_subdevdata(sd);
+
+ ret = i2c_master_send(client, data, 3);
+ if (ret < 3) {
+ v4l2_dbg(1, debug, sd, "%s: i2c write error, reg: %x\n",
+ __func__, reg);
+ return ret < 0 ? ret : -EIO;
+ }
+ return 0;
+}
+
+/**
+* @short I2C Read operation
+* @param[in] i2c_client I2C client
+* @param[in] reg register address
+* @param[out] val value read
+* @return Error code
+*/
+static int ov5647_read(struct v4l2_subdev *sd, uint16_t reg, uint8_t *val)
+{
+ int ret;
+ unsigned char data_w[2] = { reg >> 8, reg & 0xff };
+ struct i2c_client *client = v4l2_get_subdevdata(sd);
+
+
+ ret = i2c_master_send(client, data_w, 2);
+
+ if (ret < 2) {
+ v4l2_dbg(1, debug, sd, "%s: i2c read error, reg: %x\n",
+ __func__, reg);
+ return ret < 0 ? ret : -EIO;
+ }
+
+
+ ret = i2c_master_recv(client, val, 1);
+
+ if (ret < 1) {
+ v4l2_dbg(1, debug, sd, "%s: i2c read error, reg: %x\n",
+ __func__, reg);
+ return ret < 0 ? ret : -EIO;
+ }
+ return 0;
+}
+
+static int ov5647_write_array(struct v4l2_subdev *subdev,
+ struct regval_list *regs, int array_size)
+{
+ int i = 0;
+ int ret = 0;
+
+ if (!regs)
+ return -EINVAL;
+
+ while (i < array_size) {
+ if (regs->addr == REG_DLY)
+ mdelay(regs->data);
+ else
+ ret = ov5647_write(subdev, regs->addr, regs->data);
+
+ if (ret == -EIO)
+ return ret;
+
+ i++;
+ regs++;
+ }
+ return 0;
+}
+
+static void ov5647_set_virtual_channel(struct v4l2_subdev *subdev, int channel)
+{
+ u8 channel_id;
+
+ ov5647_read(subdev, 0x4814, &channel_id);
+ channel_id &= ~(3 << 6);
+ ov5647_write(subdev, 0x4814, channel_id | (channel << 6));
+}
+
+/**
+* @short Stream ON
+* @param[in] subdev v4l2 subdev
+* @return Error code
+*/
+void ov5647_stream_on(struct v4l2_subdev *subdev)
+{
+ ov5647_write(subdev, 0x4202, 0x00);
+ v4l2_dbg(1, debug, subdev, "Stream on");
+ ov5647_write(subdev, 0x300D, 0x00);
+
+}
+
+/**
+* @short Stream OFF
+* @param[in] subdev v4l2 subdev
+* @return Error code
+*/
+void ov5647_stream_off(struct v4l2_subdev *subdev)
+{
+ ov5647_write(subdev, 0x4202, 0x0f);
+ v4l2_dbg(1, debug, subdev, "Stream off");
+ ov5647_write(subdev, 0x300D, 0x01);
+}
+
+/****************************************************************************/
+
+/**
+ * @short Set SW standby
+ * @param[in] subdev v4l2 subdev
+ * @param[in] on_off standby on or off
+ * @return Error code
+ */
+static int sensor_s_sw_stby(struct v4l2_subdev *subdev, int on_off)
+{
+ int ret;
+ unsigned char rdval;
+
+ ret = ov5647_read(subdev, 0x0100, &rdval);
+ if (ret != 0)
+ return ret;
+
+ if (on_off == CSI_STBY_ON)
+ ret = ov5647_write(subdev, 0x0100, rdval&0xfe);
+
+ else
+ ret = ov5647_write(subdev, 0x0100, rdval|0x01);
+
+ return ret;
+}
+
+/**
+ * @short Store information about the video data format.
+ */
+static struct sensor_format_struct {
+ __u8 *desc;
+ u32 mbus_code;
+ struct regval_list *regs;
+ int regs_size;
+ int bpp;
+} sensor_formats[] = {
+ {
+ .desc = "Raw RGB Bayer",
+ .mbus_code = MEDIA_BUS_FMT_SBGGR8_1X8,
+ .regs = ov5647_640x480,
+ .regs_size = ARRAY_SIZE(ov5647_640x480),
+ .bpp = 1
+ },
+};
+#define N_FMTS ARRAY_SIZE(sensor_formats)
+
+/* ----------------------------------------------------------------------- */
+
+/**
+* @short Initialize sensor
+* @param[in] subdev v4l2 subdev
+* @param[in] val not used
+* @return Error code
+*/
+static int __sensor_init(struct v4l2_subdev *subdev)
+{
+ int ret;
+ uint8_t resetval;
+ unsigned char rdval;
+
+ v4l2_dbg(1, debug, subdev, "sensor init\n");
+
+ ret = ov5647_read(subdev, 0x0100, &rdval);
+ if (ret != 0)
+ return ret;
+
+ ov5647_write(subdev, 0x4800, 0x25);
+ ov5647_stream_off(subdev);
+
+ ret = ov5647_write_array(subdev, ov5647_640x480,
+ ARRAY_SIZE(ov5647_640x480));
+ if (ret < 0) {
+ v4l2_err(subdev, "write sensor_default_regs error\n");
+ return ret;
+ }
+
+ ov5647_set_virtual_channel(subdev, 0);
+
+ ov5647_read(subdev, 0x0100, &resetval);
+ if (!resetval&0x01) {
+ v4l2_dbg(1, debug, subdev,
+ "DEVICE WAS IN SOFTWARE STANDBY");
+ ov5647_write(subdev, 0x0100, 0x01);
+ }
+
+ ov5647_write(subdev, 0x4800, 0x04);
+ ov5647_stream_on(subdev);
+
+ return 0;
+}
+
+/**
+* @short Control sensor power state
+* @param[in] subdev v4l2 subdev
+* @param[in] on Sensor power
+* @return Error code
+*/
+static int sensor_power(struct v4l2_subdev *subdev, int on)
+{
+ int ret;
+ struct ov5647 *ov5647 = to_state(subdev);
+
+ ret = 0;
+ mutex_lock(&ov5647->lock);
+
+ switch (on) {
+ case CSI_SUBDEV_PWR_OFF:
+ v4l2_dbg(1, debug, subdev, "CSI SUBDEV PWR OFF!\n");
+
+ v4l2_dbg(1, debug, subdev, "disable oe!\n");
+ ret = ov5647_write_array(subdev, sensor_oe_disable_regs,
+ ARRAY_SIZE(sensor_oe_disable_regs));
+
+ if (ret < 0)
+ v4l2_dbg(1, debug, subdev, "disable oe failed!\n");
+
+ ret = sensor_s_sw_stby(subdev, CSI_STBY_ON);
+
+ if (ret < 0)
+ v4l2_dbg(1, debug, subdev, "soft stby failed!\n");
+
+ break;
+ case CSI_SUBDEV_PWR_ON:
+ v4l2_dbg(1, debug, subdev, "CSI SUBDEV PWR ON!\n");
+
+ ret = ov5647_write_array(subdev, sensor_oe_enable_regs,
+ ARRAY_SIZE(sensor_oe_enable_regs));
+
+ ret = __sensor_init(subdev);
+
+ if (ret < 0) {
+ v4l2_err(subdev,
+ "Camera not available! Check Power!\n");
+ break;
+ }
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ mutex_unlock(&ov5647->lock);
+
+ return 0;
+}
+
+#ifdef CONFIG_VIDEO_ADV_DEBUG
+/**
+* @short Get register value
+* @param[in] subdev v4l2 subdev
+* @param[in] reg register struct
+* @return Error code
+*/
+static int sensor_get_register(struct v4l2_subdev *subdev,
+ struct v4l2_dbg_register *reg)
+{
+ unsigned char val = 0;
+ int ret;
+
+ ret = ov5647_read(subdev, reg->reg & 0xff, &val);
+ reg->val = val;
+ reg->size = 1;
+ return ret;
+}
+
+/**
+* @short Set register value
+* @param[in] subdev v4l2 subdev
+* @param[in] reg register struct
+* @return Error code
+*/
+static int sensor_set_register(struct v4l2_subdev *subdev,
+ const struct v4l2_dbg_register *reg)
+{
+ ov5647_write(subdev, reg->reg & 0xff, reg->val & 0xff);
+ return 0;
+}
+#endif
+
+/* ----------------------------------------------------------------------- */
+
+/**
+ * @short Subdev core operations registration
+ */
+static const struct v4l2_subdev_core_ops sensor_core_ops = {
+ .s_power = sensor_power,
+#ifdef CONFIG_VIDEO_ADV_DEBUG
+ .g_register = sensor_get_register,
+ .s_register = sensor_set_register,
+#endif
+};
+
+/* ----------------------------------------------------------------------- */
+
+
+
+/**
+* @short Enumerate available image formats
+* @param[in] subdev v4l2 subdev
+* @param[in] index index
+* @param[in] code MBUS Pixel code
+* @return Error code
+*/
+static int sensor_enum_fmt(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_mbus_code_enum *code)
+{
+ if (code->pad || code->index >= N_FMTS)
+ return -EINVAL;
+
+ code->code = sensor_formats[code->index].mbus_code;
+ return 0;
+}
+
+/**
+* @short Try frame format internal function
+* @param[in] subdev v4l2 subdev
+* @param[in] fmt frame format
+* @return Error code
+*/
+static int sensor_try_fmt_internal(struct v4l2_subdev *subdev,
+ struct v4l2_mbus_framefmt *fmt, struct sensor_format_struct **ret_fmt,
+ struct sensor_win_size **ret_wsize)
+{
+ int index;
+
+ for (index = 0; index < N_FMTS; index++)
+ if (sensor_formats[index].mbus_code == fmt->code)
+ break;
+
+ if (index >= N_FMTS)
+ return -EINVAL;
+
+ if (ret_fmt != NULL)
+ *ret_fmt = sensor_formats + index;
+
+ fmt->field = V4L2_FIELD_NONE;
+
+ return 0;
+}
+
+/**
+* @short Set frame format
+* @param[in] subdev v4l2 subdev
+* @param[in] fmt frame format
+* @return Error code
+*/
+static int sensor_s_fmt(struct v4l2_subdev *subdev,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_format *fmt)
+{
+ int ret;
+ struct sensor_format_struct *sensor_fmt;
+ struct sensor_win_size *wsize;
+ struct ov5647 *info = to_state(subdev);
+
+ ov5647_write_array(subdev, sensor_oe_disable_regs,
+ ARRAY_SIZE(sensor_oe_disable_regs));
+
+ ret = sensor_try_fmt_internal(subdev, &fmt->format,
+ &sensor_fmt, &wsize);
+ if (ret)
+ return ret;
+
+ ov5647_write_array(subdev, sensor_fmt->regs, sensor_fmt->regs_size);
+
+ ret = 0;
+
+ if (wsize->regs)
+ ov5647_write_array(subdev, wsize->regs, wsize->regs_size);
+
+ if (wsize->set_size)
+ wsize->set_size(subdev);
+
+ info->fmt = sensor_fmt;
+ info->width = wsize->width;
+ info->height = wsize->height;
+
+ ov5647_write_array(subdev, sensor_oe_enable_regs,
+ ARRAY_SIZE(sensor_oe_enable_regs));
+
+ return 0;
+}
+
+/**
+* @short Set stream parameters
+* @param[in] subdev v4l2 subdev
+* @param[in] parms stream parameters
+* @return Error code
+*/
+static int sensor_s_parm(struct v4l2_subdev *subdev,
+ struct v4l2_streamparm *parms)
+{
+ struct v4l2_captureparm *cp = &parms->parm.capture;
+ struct ov5647 *info = to_state(subdev);
+
+ if (parms->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+ return -EINVAL;
+
+ if (info->tpf.numerator == 0)
+ return -EINVAL;
+
+ info->capture_mode = cp->capturemode;
+
+ return 0;
+}
+
+/**
+* @short Get stream parameters
+* @param[in] subdev v4l2 subdev
+* @param[in] parms stream parameters
+* @return Error code
+*/
+static int sensor_g_parm(struct v4l2_subdev *subdev,
+ struct v4l2_streamparm *parms)
+{
+ struct v4l2_captureparm *cp = &parms->parm.capture;
+ struct ov5647 *info = to_state(subdev);
+
+ if (parms->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+ return -EINVAL;
+
+ memset(cp, 0, sizeof(struct v4l2_captureparm));
+ cp->capability = V4L2_CAP_TIMEPERFRAME;
+ cp->capturemode = info->capture_mode;
+
+ return 0;
+}
+
+static const struct v4l2_subdev_pad_ops ov7670_pad_ops = {
+ .enum_mbus_code = sensor_enum_fmt,
+ .set_fmt = sensor_s_fmt,
+};
+
+/**
+ * @short Subdev video operations registration
+ *
+ */
+static const struct v4l2_subdev_video_ops sensor_video_ops = {
+ .s_parm = sensor_s_parm,
+ .g_parm = sensor_g_parm,
+};
+
+/* ----------------------------------------------------------------------- */
+
+/**
+ * @short Subdev operations registration
+ *
+ */
+static const struct v4l2_subdev_ops subdev_ops = {
+ .core = &sensor_core_ops,
+ .video = &sensor_video_ops,
+};
+
+/* -----------------------------------------------------------------------------
+ * V4L2 subdev internal operations
+ */
+
+/**
+* @short Detect camera version and model
+* @param[in] subdev v4l2 subdev
+* @return Error code
+*/
+int ov5647_detect(struct v4l2_subdev *sd)
+{
+ unsigned char v;
+ int ret;
+
+ ret = sensor_power(sd, 1);
+ if (ret < 0)
+ return ret;
+ ret = ov5647_read(sd, OV5647_REG_CHIPID_H, &v);
+ if (ret < 0)
+ return ret;
+ if (v != 0x56) /* OV manuf. id. */
+ return -ENODEV;
+ ret = ov5647_read(sd, OV5647_REG_CHIPID_L, &v);
+ if (ret < 0)
+ return ret;
+ if (v != 0x47)
+ return -ENODEV;
+
+ ret = sensor_power(sd, 0);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+
+/**
+* @short Detect if camera is registered
+* @param[in] subdev v4l2 subdev
+* @return Error code
+*/
+static int ov5647_registered(struct v4l2_subdev *subdev)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(subdev);
+
+ v4l2_info(subdev, "OV5647 detected at address 0x%02x\n", client->addr);
+
+ return 0;
+}
+
+/**
+* @short Open device
+* @param[in] subdev v4l2 subdev
+* @param[in] fh v4l2 file handler
+* @return Error code
+*/
+static int ov5647_open(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+ struct v4l2_mbus_framefmt *format =
+ v4l2_subdev_get_try_format(subdev, fh->pad, 0);
+ struct v4l2_rect *crop =
+ v4l2_subdev_get_try_crop(subdev, fh->pad, 0);
+
+ crop->left = OV5647_COLUMN_START_DEF;
+ crop->top = OV5647_ROW_START_DEF;
+ crop->width = OV5647_WINDOW_WIDTH_DEF;
+ crop->height = OV5647_WINDOW_HEIGHT_DEF;
+
+ format->code = MEDIA_BUS_FMT_SBGGR8_1X8;
+
+ format->width = OV5647_WINDOW_WIDTH_DEF;
+ format->height = OV5647_WINDOW_HEIGHT_DEF;
+ format->field = V4L2_FIELD_NONE;
+ format->colorspace = V4L2_COLORSPACE_SRGB;
+
+ return sensor_power(subdev, 1);
+}
+
+/**
+* @short Open device
+* @param[in] subdev v4l2 subdev
+* @param[in] fh v4l2 file handler
+* @return Error code
+*/
+static int ov5647_close(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+ return sensor_power(subdev, 0);
+}
+
+/**
+ * @short Subdev internal operations registration
+ *
+ */
+static const struct v4l2_subdev_internal_ops ov5647_subdev_internal_ops = {
+ .registered = ov5647_registered,
+ .open = ov5647_open,
+ .close = ov5647_close,
+};
+
+/**
+* @short Initialization routine - Entry point of the driver
+* @param[in] client pointer to the i2c client structure
+* @param[in] id pointer to the i2c device id structure
+* @return 0 on success and a negative number on failure
+* Refer to Linux errors.
+*/
+static int ov5647_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct device *dev = &client->dev;
+ struct ov5647 *sensor;
+ int ret = 0;
+ struct v4l2_subdev *sd;
+
+ pr_info("Installing OmniVision OV5647 camera driver\n");
+
+ sensor = devm_kzalloc(dev, sizeof(*sensor), GFP_KERNEL);
+ if (sensor == NULL)
+ return -ENOMEM;
+
+ mutex_init(&sensor->lock);
+ sensor->dev = dev;
+
+ sd = &sensor->subdev;
+ v4l2_i2c_subdev_init(sd, client, &subdev_ops);
+ sensor->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+
+ sensor->pad.flags = MEDIA_PAD_FL_SOURCE;
+ ret = media_entity_pads_init(&sd->entity, 1, &sensor->pad);
+ if (ret < 0)
+ return ret;
+
+
+ ret = v4l2_async_register_subdev(sd);
+ if (ret < 0)
+ media_entity_cleanup(&sd->entity);
+
+ return ret;
+}
+
+/**
+* @short Exit routine - Exit point of the driver
+* @param[in] client pointer to the i2c clietn structure
+* @return 0 on success and a negative number on failure
+* Refer to Linux errors.
+*/
+static int ov5647_remove(struct i2c_client *client)
+{
+ struct v4l2_subdev *subdev = i2c_get_clientdata(client);
+ struct ov5647 *ov5647 = to_state(subdev);
+
+ v4l2_async_unregister_subdev(&ov5647->subdev);
+ media_entity_cleanup(&ov5647->subdev.entity);
+ v4l2_device_unregister_subdev(subdev);
+
+ return 0;
+}
+
+/**
+* @short of_device_id structure
+*/
+static const struct i2c_device_id ov5647_id[] = {
+ { "ov5647", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, ov5647_id);
+
+#if IS_ENABLED(CONFIG_OF)
+static const struct of_device_id ov5647_of_match[] = {
+ { .compatible = "ov5647", 0 },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, ov5647_of_match);
+#endif
+
+/**
+* @short i2c driver structure
+*/
+static struct i2c_driver ov5647_driver = {
+ .driver = {
+ .of_match_table = of_match_ptr(ov5647_of_match),
+ .owner = THIS_MODULE,
+ .name = "ov5647",
+ },
+ .probe = ov5647_probe,
+ .remove = ov5647_remove,
+ .id_table = ov5647_id,
+};
+
+module_i2c_driver(ov5647_driver);
+
+MODULE_AUTHOR("Ramiro Oliveira <roliveir@synopsys.com>");
+MODULE_DESCRIPTION("A low-level driver for OmniVision ov5647 sensors");
+MODULE_LICENSE("GPL");
--
2.8.1
^ permalink raw reply related [flat|nested] 4+ messages in thread