[PATCH v5 00/39] i.MX Media Driver

[PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

In version 5:

- ov5640: renamed "pwdn-gpios" to "powerdown-gpios"

- ov5640: add mutex lock around the subdev op entry points.

- ov5640: don't attempt to program the new mode in ov5640_set_fmt().
  Instead set a new flag, pending_mode_change, and program the new
  mode at s_stream() if flag is set.

- ov5640: implement [gs]_frame_interval. As part of that, create
  ov5640_try_frame_interval(), which is used by both [gs]_frame_interval
  and [gs]_parm.

- ov5640: don't attempt to set controls in ov5640_s_ctrl(), or at
  mode change, do it instead after first power-up.

- video-multiplexer: include link_validate in media_entity_operations.

- video-multiplexer: enforce that output pad frame interval must match
  input pad frame interval in vidsw_s_frame_interval().

- video-multiplexer: initialize frame interval to a default 30 fps.

- mipi csi-2: renamed "cfg" clock name property to "ref". This is the
  27 MHz mipi csi-2 PLL reference clock.

- mipi csi-2: create a hsfreq_map[] table based on
  https://community.nxp.com/docs/DOC-94312. Use it to select
  a hsfreqrange_sel value when programming the D-PHY, based on
  a max Mbps per lane. This is computed from the source subdev
  via V4L2_CID_LINK_FREQ control, and if the subdev doesn't implement
  that control, use a default hard-coded max Mbps per lane.

- added required ports property description to imx-media binding doc.

- removed event V4L2_EVENT_FRAME_TIMEOUT. On a frame timeout, which
  is always unrecoverable, call vb2_queue_error() instead.

- export the remaining custom events to V4L2_EVENT_FRAME_INTERVAL_ERROR
  and V4L2_EVENT_NEW_FRAME_BEFORE_EOF.

- vdic: use V4L2_CID_DEINTERLACING_MODE for motion compensation control
  instead of a custom control.

- add v4l2_subdev_link_validate_frame_interval(). Call this in the
  link_validate imx-media subdev callbacks and video-multiplexer.

- fix subdev event registration: implementation of subscribe_event()
  and unsubscribe_event() subdev ops were missing.

- all calls from the pipeline to the sensor subdev have been removed.
  Only the CSI subdev still refers to a sensor, and only to retrieve
  its media bus config, which is necessary to setup the CSI interface.

- add mutex locks around the imx-media subdev op entry points.

- completed the propagation of all pad format parameters from sink
  pads to source pads within every imx-media subdev.

- implement [gs]_frame_interval in all the imx-media subdevs.

- imx-ic-prpencvf: there isn't necessarily a CSI subdev in the pipeline
  in the future, so make sure this is optional when calling the CSI's
  FIM.

- the source pads that attach to capture device nodes now require the
  IPU internal pixel codes. The capture device translates these to
  v4l2 fourcc memory formats.

- fix control inheritance to the capture device. When the pipeline
  was modified, the inherited controls were not being refreshed.
  v4l2_pipeline_inherit_controls() is now called only in imx-media
  link_notify() callback when a pipelink link is disabled or modified.
  imx_media_find_pipeline_video_device() is created to locate the
  capture device in the pipeline.

- fix a possible race when propagating formats to the capture device.
  The subdevs and capture device use different mutex locks when setting
  formats. imx_media_capture_device_set_format() is created which acquires
  the capture device mutex when updating the capture device format.

- verify all subdevs were bound in the async completion callback.
 

Philipp Zabel (7):
  [media] dt-bindings: Add bindings for video-multiplexer device
  ARM: dts: imx6qdl: Add mipi_ipu1/2 multiplexers, mipi_csi, and their
    connections
  add mux and video interface bridge entity functions
  platform: add video-multiplexer subdevice driver
  media: imx: csi: fix crop rectangle changes in set_fmt
  media: imx: csi: add frame skipping support
  media: imx: csi: fix crop rectangle reset in sink set_fmt

Russell King (4):
  media: imx: add support for bayer formats
  media: imx: csi: add support for bayer formats
  media: imx: mipi-csi2: enable setting and getting of frame rates
  media: imx: csi/fim: add support for frame intervals

Steve Longerbeam (28):
  [media] dt-bindings: Add bindings for i.MX media driver
  [media] dt/bindings: Add bindings for OV5640
  ARM: dts: imx6qdl: Add compatible, clocks, irqs to MIPI CSI-2 node
  ARM: dts: imx6qdl: add capture-subsystem device
  ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround
  ARM: dts: imx6-sabrelite: add OV5642 and OV5640 camera sensors
  ARM: dts: imx6-sabresd: add OV5642 and OV5640 camera sensors
  ARM: dts: imx6-sabreauto: create i2cmux for i2c3
  ARM: dts: imx6-sabreauto: add reset-gpios property for max7310_b
  ARM: dts: imx6-sabreauto: add pinctrl for gpt input capture
  ARM: dts: imx6-sabreauto: add the ADV7180 video decoder
  [media] v4l2: add a frame interval error event
  [media] v4l2: add a new-frame before end-of-frame event
  [media] v4l2-mc: add a function to inherit controls from a pipeline
  [media] v4l: subdev: Add function to validate frame interval
  [media] add Omnivision OV5640 sensor driver
  UAPI: Add media UAPI Kbuild file
  media: Add userspace header file for i.MX
  media: Add i.MX media core driver
  media: imx: Add Capture Device Interface
  media: imx: Add CSI subdev driver
  media: imx: Add VDIC subdev driver
  media: imx: Add IC subdev drivers
  media: imx: Add MIPI CSI-2 Receiver subdev driver
  ARM: imx_v6_v7_defconfig: Enable staging video4linux drivers
  media: imx: csi: add __csi_get_fmt
  media: imx: redo pixel format enumeration and negotiation
  media: imx: propagate sink pad formats to source pads

 .../devicetree/bindings/media/i2c/ov5640.txt       |   45 +
 Documentation/devicetree/bindings/media/imx.txt    |   74 +
 .../bindings/media/video-multiplexer.txt           |   59 +
 Documentation/media/uapi/mediactl/media-types.rst  |   22 +
 Documentation/media/uapi/v4l/vidioc-dqevent.rst    |   12 +
 Documentation/media/v4l-drivers/imx.rst            |  560 +++++
 Documentation/media/videodev2.h.rst.exceptions     |    2 +
 arch/arm/boot/dts/imx6dl-sabrelite.dts             |    5 +
 arch/arm/boot/dts/imx6dl-sabresd.dts               |    5 +
 arch/arm/boot/dts/imx6dl.dtsi                      |  185 ++
 arch/arm/boot/dts/imx6q-sabrelite.dts              |    5 +
 arch/arm/boot/dts/imx6q-sabresd.dts                |    5 +
 arch/arm/boot/dts/imx6q.dtsi                       |  121 ++
 arch/arm/boot/dts/imx6qdl-sabreauto.dtsi           |  144 +-
 arch/arm/boot/dts/imx6qdl-sabrelite.dtsi           |  152 +-
 arch/arm/boot/dts/imx6qdl-sabresd.dtsi             |  114 +-
 arch/arm/boot/dts/imx6qdl.dtsi                     |   17 +-
 arch/arm/configs/imx_v6_v7_defconfig               |   11 +
 drivers/media/i2c/Kconfig                          |    7 +
 drivers/media/i2c/Makefile                         |    1 +
 drivers/media/i2c/ov5640.c                         | 2231 ++++++++++++++++++++
 drivers/media/platform/Kconfig                     |    8 +
 drivers/media/platform/Makefile                    |    2 +
 drivers/media/platform/video-multiplexer.c         |  498 +++++
 drivers/media/v4l2-core/v4l2-mc.c                  |   48 +
 drivers/media/v4l2-core/v4l2-subdev.c              |   50 +
 drivers/staging/media/Kconfig                      |    2 +
 drivers/staging/media/Makefile                     |    1 +
 drivers/staging/media/imx/Kconfig                  |   20 +
 drivers/staging/media/imx/Makefile                 |   12 +
 drivers/staging/media/imx/TODO                     |   17 +
 drivers/staging/media/imx/imx-ic-common.c          |  113 +
 drivers/staging/media/imx/imx-ic-prp.c             |  497 +++++
 drivers/staging/media/imx/imx-ic-prpencvf.c        | 1236 +++++++++++
 drivers/staging/media/imx/imx-ic.h                 |   38 +
 drivers/staging/media/imx/imx-media-capture.c      |  694 ++++++
 drivers/staging/media/imx/imx-media-csi.c          | 1595 ++++++++++++++
 drivers/staging/media/imx/imx-media-dev.c          |  522 +++++
 drivers/staging/media/imx/imx-media-fim.c          |  463 ++++
 drivers/staging/media/imx/imx-media-internal-sd.c  |  349 +++
 drivers/staging/media/imx/imx-media-of.c           |  267 +++
 drivers/staging/media/imx/imx-media-utils.c        | 1009 +++++++++
 drivers/staging/media/imx/imx-media-vdic.c         |  949 +++++++++
 drivers/staging/media/imx/imx-media.h              |  311 +++
 drivers/staging/media/imx/imx6-mipi-csi2.c         |  725 +++++++
 include/media/imx.h                                |   15 +
 include/media/v4l2-mc.h                            |   25 +
 include/media/v4l2-subdev.h                        |   10 +
 include/uapi/Kbuild                                |    1 +
 include/uapi/linux/media.h                         |    6 +
 include/uapi/linux/v4l2-controls.h                 |    4 +
 include/uapi/linux/videodev2.h                     |    2 +
 include/uapi/media/Kbuild                          |    2 +
 include/uapi/media/imx.h                           |   21 +
 54 files changed, 13262 insertions(+), 27 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/ov5640.txt
 create mode 100644 Documentation/devicetree/bindings/media/imx.txt
 create mode 100644 Documentation/devicetree/bindings/media/video-multiplexer.txt
 create mode 100644 Documentation/media/v4l-drivers/imx.rst
 create mode 100644 drivers/media/i2c/ov5640.c
 create mode 100644 drivers/media/platform/video-multiplexer.c
 create mode 100644 drivers/staging/media/imx/Kconfig
 create mode 100644 drivers/staging/media/imx/Makefile
 create mode 100644 drivers/staging/media/imx/TODO
 create mode 100644 drivers/staging/media/imx/imx-ic-common.c
 create mode 100644 drivers/staging/media/imx/imx-ic-prp.c
 create mode 100644 drivers/staging/media/imx/imx-ic-prpencvf.c
 create mode 100644 drivers/staging/media/imx/imx-ic.h
 create mode 100644 drivers/staging/media/imx/imx-media-capture.c
 create mode 100644 drivers/staging/media/imx/imx-media-csi.c
 create mode 100644 drivers/staging/media/imx/imx-media-dev.c
 create mode 100644 drivers/staging/media/imx/imx-media-fim.c
 create mode 100644 drivers/staging/media/imx/imx-media-internal-sd.c
 create mode 100644 drivers/staging/media/imx/imx-media-of.c
 create mode 100644 drivers/staging/media/imx/imx-media-utils.c
 create mode 100644 drivers/staging/media/imx/imx-media-vdic.c
 create mode 100644 drivers/staging/media/imx/imx-media.h
 create mode 100644 drivers/staging/media/imx/imx6-mipi-csi2.c
 create mode 100644 include/media/imx.h
 create mode 100644 include/uapi/media/Kbuild
 create mode 100644 include/uapi/media/imx.h

-- 
2.7.4

[PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

In version 5:

- ov5640: renamed "pwdn-gpios" to "powerdown-gpios"

- ov5640: add mutex lock around the subdev op entry points.

- ov5640: don't attempt to program the new mode in ov5640_set_fmt().
  Instead set a new flag, pending_mode_change, and program the new
  mode at s_stream() if flag is set.

- ov5640: implement [gs]_frame_interval. As part of that, create
  ov5640_try_frame_interval(), which is used by both [gs]_frame_interval
  and [gs]_parm.

- ov5640: don't attempt to set controls in ov5640_s_ctrl(), or at
  mode change, do it instead after first power-up.

- video-multiplexer: include link_validate in media_entity_operations.

- video-multiplexer: enforce that output pad frame interval must match
  input pad frame interval in vidsw_s_frame_interval().

- video-multiplexer: initialize frame interval to a default 30 fps.

- mipi csi-2: renamed "cfg" clock name property to "ref". This is the
  27 MHz mipi csi-2 PLL reference clock.

- mipi csi-2: create a hsfreq_map[] table based on
  https://community.nxp.com/docs/DOC-94312. Use it to select
  a hsfreqrange_sel value when programming the D-PHY, based on
  a max Mbps per lane. This is computed from the source subdev
  via V4L2_CID_LINK_FREQ control, and if the subdev doesn't implement
  that control, use a default hard-coded max Mbps per lane.

- added required ports property description to imx-media binding doc.

- removed event V4L2_EVENT_FRAME_TIMEOUT. On a frame timeout, which
  is always unrecoverable, call vb2_queue_error() instead.

- export the remaining custom events to V4L2_EVENT_FRAME_INTERVAL_ERROR
  and V4L2_EVENT_NEW_FRAME_BEFORE_EOF.

- vdic: use V4L2_CID_DEINTERLACING_MODE for motion compensation control
  instead of a custom control.

- add v4l2_subdev_link_validate_frame_interval(). Call this in the
  link_validate imx-media subdev callbacks and video-multiplexer.

- fix subdev event registration: implementation of subscribe_event()
  and unsubscribe_event() subdev ops were missing.

- all calls from the pipeline to the sensor subdev have been removed.
  Only the CSI subdev still refers to a sensor, and only to retrieve
  its media bus config, which is necessary to setup the CSI interface.

- add mutex locks around the imx-media subdev op entry points.

- completed the propagation of all pad format parameters from sink
  pads to source pads within every imx-media subdev.

- implement [gs]_frame_interval in all the imx-media subdevs.

- imx-ic-prpencvf: there isn't necessarily a CSI subdev in the pipeline
  in the future, so make sure this is optional when calling the CSI's
  FIM.

- the source pads that attach to capture device nodes now require the
  IPU internal pixel codes. The capture device translates these to
  v4l2 fourcc memory formats.

- fix control inheritance to the capture device. When the pipeline
  was modified, the inherited controls were not being refreshed.
  v4l2_pipeline_inherit_controls() is now called only in imx-media
  link_notify() callback when a pipelink link is disabled or modified.
  imx_media_find_pipeline_video_device() is created to locate the
  capture device in the pipeline.

- fix a possible race when propagating formats to the capture device.
  The subdevs and capture device use different mutex locks when setting
  formats. imx_media_capture_device_set_format() is created which acquires
  the capture device mutex when updating the capture device format.

- verify all subdevs were bound in the async completion callback.
 

Philipp Zabel (7):
  [media] dt-bindings: Add bindings for video-multiplexer device
  ARM: dts: imx6qdl: Add mipi_ipu1/2 multiplexers, mipi_csi, and their
    connections
  add mux and video interface bridge entity functions
  platform: add video-multiplexer subdevice driver
  media: imx: csi: fix crop rectangle changes in set_fmt
  media: imx: csi: add frame skipping support
  media: imx: csi: fix crop rectangle reset in sink set_fmt

Russell King (4):
  media: imx: add support for bayer formats
  media: imx: csi: add support for bayer formats
  media: imx: mipi-csi2: enable setting and getting of frame rates
  media: imx: csi/fim: add support for frame intervals

Steve Longerbeam (28):
  [media] dt-bindings: Add bindings for i.MX media driver
  [media] dt/bindings: Add bindings for OV5640
  ARM: dts: imx6qdl: Add compatible, clocks, irqs to MIPI CSI-2 node
  ARM: dts: imx6qdl: add capture-subsystem device
  ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround
  ARM: dts: imx6-sabrelite: add OV5642 and OV5640 camera sensors
  ARM: dts: imx6-sabresd: add OV5642 and OV5640 camera sensors
  ARM: dts: imx6-sabreauto: create i2cmux for i2c3
  ARM: dts: imx6-sabreauto: add reset-gpios property for max7310_b
  ARM: dts: imx6-sabreauto: add pinctrl for gpt input capture
  ARM: dts: imx6-sabreauto: add the ADV7180 video decoder
  [media] v4l2: add a frame interval error event
  [media] v4l2: add a new-frame before end-of-frame event
  [media] v4l2-mc: add a function to inherit controls from a pipeline
  [media] v4l: subdev: Add function to validate frame interval
  [media] add Omnivision OV5640 sensor driver
  UAPI: Add media UAPI Kbuild file
  media: Add userspace header file for i.MX
  media: Add i.MX media core driver
  media: imx: Add Capture Device Interface
  media: imx: Add CSI subdev driver
  media: imx: Add VDIC subdev driver
  media: imx: Add IC subdev drivers
  media: imx: Add MIPI CSI-2 Receiver subdev driver
  ARM: imx_v6_v7_defconfig: Enable staging video4linux drivers
  media: imx: csi: add __csi_get_fmt
  media: imx: redo pixel format enumeration and negotiation
  media: imx: propagate sink pad formats to source pads

 .../devicetree/bindings/media/i2c/ov5640.txt       |   45 +
 Documentation/devicetree/bindings/media/imx.txt    |   74 +
 .../bindings/media/video-multiplexer.txt           |   59 +
 Documentation/media/uapi/mediactl/media-types.rst  |   22 +
 Documentation/media/uapi/v4l/vidioc-dqevent.rst    |   12 +
 Documentation/media/v4l-drivers/imx.rst            |  560 +++++
 Documentation/media/videodev2.h.rst.exceptions     |    2 +
 arch/arm/boot/dts/imx6dl-sabrelite.dts             |    5 +
 arch/arm/boot/dts/imx6dl-sabresd.dts               |    5 +
 arch/arm/boot/dts/imx6dl.dtsi                      |  185 ++
 arch/arm/boot/dts/imx6q-sabrelite.dts              |    5 +
 arch/arm/boot/dts/imx6q-sabresd.dts                |    5 +
 arch/arm/boot/dts/imx6q.dtsi                       |  121 ++
 arch/arm/boot/dts/imx6qdl-sabreauto.dtsi           |  144 +-
 arch/arm/boot/dts/imx6qdl-sabrelite.dtsi           |  152 +-
 arch/arm/boot/dts/imx6qdl-sabresd.dtsi             |  114 +-
 arch/arm/boot/dts/imx6qdl.dtsi                     |   17 +-
 arch/arm/configs/imx_v6_v7_defconfig               |   11 +
 drivers/media/i2c/Kconfig                          |    7 +
 drivers/media/i2c/Makefile                         |    1 +
 drivers/media/i2c/ov5640.c                         | 2231 ++++++++++++++++++++
 drivers/media/platform/Kconfig                     |    8 +
 drivers/media/platform/Makefile                    |    2 +
 drivers/media/platform/video-multiplexer.c         |  498 +++++
 drivers/media/v4l2-core/v4l2-mc.c                  |   48 +
 drivers/media/v4l2-core/v4l2-subdev.c              |   50 +
 drivers/staging/media/Kconfig                      |    2 +
 drivers/staging/media/Makefile                     |    1 +
 drivers/staging/media/imx/Kconfig                  |   20 +
 drivers/staging/media/imx/Makefile                 |   12 +
 drivers/staging/media/imx/TODO                     |   17 +
 drivers/staging/media/imx/imx-ic-common.c          |  113 +
 drivers/staging/media/imx/imx-ic-prp.c             |  497 +++++
 drivers/staging/media/imx/imx-ic-prpencvf.c        | 1236 +++++++++++
 drivers/staging/media/imx/imx-ic.h                 |   38 +
 drivers/staging/media/imx/imx-media-capture.c      |  694 ++++++
 drivers/staging/media/imx/imx-media-csi.c          | 1595 ++++++++++++++
 drivers/staging/media/imx/imx-media-dev.c          |  522 +++++
 drivers/staging/media/imx/imx-media-fim.c          |  463 ++++
 drivers/staging/media/imx/imx-media-internal-sd.c  |  349 +++
 drivers/staging/media/imx/imx-media-of.c           |  267 +++
 drivers/staging/media/imx/imx-media-utils.c        | 1009 +++++++++
 drivers/staging/media/imx/imx-media-vdic.c         |  949 +++++++++
 drivers/staging/media/imx/imx-media.h              |  311 +++
 drivers/staging/media/imx/imx6-mipi-csi2.c         |  725 +++++++
 include/media/imx.h                                |   15 +
 include/media/v4l2-mc.h                            |   25 +
 include/media/v4l2-subdev.h                        |   10 +
 include/uapi/Kbuild                                |    1 +
 include/uapi/linux/media.h                         |    6 +
 include/uapi/linux/v4l2-controls.h                 |    4 +
 include/uapi/linux/videodev2.h                     |    2 +
 include/uapi/media/Kbuild                          |    2 +
 include/uapi/media/imx.h                           |   21 +
 54 files changed, 13262 insertions(+), 27 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/ov5640.txt
 create mode 100644 Documentation/devicetree/bindings/media/imx.txt
 create mode 100644 Documentation/devicetree/bindings/media/video-multiplexer.txt
 create mode 100644 Documentation/media/v4l-drivers/imx.rst
 create mode 100644 drivers/media/i2c/ov5640.c
 create mode 100644 drivers/media/platform/video-multiplexer.c
 create mode 100644 drivers/staging/media/imx/Kconfig
 create mode 100644 drivers/staging/media/imx/Makefile
 create mode 100644 drivers/staging/media/imx/TODO
 create mode 100644 drivers/staging/media/imx/imx-ic-common.c
 create mode 100644 drivers/staging/media/imx/imx-ic-prp.c
 create mode 100644 drivers/staging/media/imx/imx-ic-prpencvf.c
 create mode 100644 drivers/staging/media/imx/imx-ic.h
 create mode 100644 drivers/staging/media/imx/imx-media-capture.c
 create mode 100644 drivers/staging/media/imx/imx-media-csi.c
 create mode 100644 drivers/staging/media/imx/imx-media-dev.c
 create mode 100644 drivers/staging/media/imx/imx-media-fim.c
 create mode 100644 drivers/staging/media/imx/imx-media-internal-sd.c
 create mode 100644 drivers/staging/media/imx/imx-media-of.c
 create mode 100644 drivers/staging/media/imx/imx-media-utils.c
 create mode 100644 drivers/staging/media/imx/imx-media-vdic.c
 create mode 100644 drivers/staging/media/imx/imx-media.h
 create mode 100644 drivers/staging/media/imx/imx6-mipi-csi2.c
 create mode 100644 include/media/imx.h
 create mode 100644 include/uapi/media/Kbuild
 create mode 100644 include/uapi/media/imx.h

-- 
2.7.4

[PATCH v5 01/39] [media] dt-bindings: Add bindings for video-multiplexer device

[Steve Longerbeam]

From: Philipp Zabel <p.zabel@pengutronix.de>

Add bindings documentation for the video multiplexer device.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 .../bindings/media/video-multiplexer.txt           | 59 ++++++++++++++++++++++
 1 file changed, 59 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/video-multiplexer.txt

diff --git a/Documentation/devicetree/bindings/media/video-multiplexer.txt b/Documentation/devicetree/bindings/media/video-multiplexer.txt
new file mode 100644
index 0000000..9d133d9
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/video-multiplexer.txt
@@ -0,0 +1,59 @@
+Video Multiplexer
+=================
+
+Video multiplexers allow to select between multiple input ports. Video received
+on the active input port is passed through to the output port. Muxes described
+by this binding may be controlled by a syscon register bitfield or by a GPIO.
+
+Required properties:
+- compatible : should be "video-multiplexer"
+- reg: should be register base of the register containing the control bitfield
+- bit-mask: bitmask of the control bitfield in the control register
+- bit-shift: bit offset of the control bitfield in the control register
+- gpios: alternatively to reg, bit-mask, and bit-shift, a single GPIO phandle
+  may be given to switch between two inputs
+- #address-cells: should be <1>
+- #size-cells: should be <0>
+- port@*: at least three port nodes containing endpoints connecting to the
+  source and sink devices according to of_graph bindings. The last port is
+  the output port, all others are inputs.
+
+Example:
+
+syscon {
+	compatible = "syscon", "simple-mfd";
+
+	mux {
+		compatible = "video-multiplexer";
+		/* Single bit (1 << 19) in syscon register 0x04: */
+		reg = <0x04>;
+		bit-mask = <1>;
+		bit-shift = <19>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			mux_in0: endpoint {
+				remote-endpoint = <&video_source0_out>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			mux_in1: endpoint {
+				remote-endpoint = <&video_source1_out>;
+			};
+		};
+
+		port@2 {
+			reg = <2>;
+
+			mux_out: endpoint {
+				remote-endpoint = <&capture_interface_in>;
+			};
+		};
+	};
+};
-- 
2.7.4

[PATCH v5 01/39] [media] dt-bindings: Add bindings for video-multiplexer device

[Steve Longerbeam]

From: Philipp Zabel <p.zabel@pengutronix.de>

Add bindings documentation for the video multiplexer device.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 .../bindings/media/video-multiplexer.txt           | 59 ++++++++++++++++++++++
 1 file changed, 59 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/video-multiplexer.txt

diff --git a/Documentation/devicetree/bindings/media/video-multiplexer.txt b/Documentation/devicetree/bindings/media/video-multiplexer.txt
new file mode 100644
index 0000000..9d133d9
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/video-multiplexer.txt
@@ -0,0 +1,59 @@
+Video Multiplexer
+=================
+
+Video multiplexers allow to select between multiple input ports. Video received
+on the active input port is passed through to the output port. Muxes described
+by this binding may be controlled by a syscon register bitfield or by a GPIO.
+
+Required properties:
+- compatible : should be "video-multiplexer"
+- reg: should be register base of the register containing the control bitfield
+- bit-mask: bitmask of the control bitfield in the control register
+- bit-shift: bit offset of the control bitfield in the control register
+- gpios: alternatively to reg, bit-mask, and bit-shift, a single GPIO phandle
+  may be given to switch between two inputs
+- #address-cells: should be <1>
+- #size-cells: should be <0>
+- port@*: at least three port nodes containing endpoints connecting to the
+  source and sink devices according to of_graph bindings. The last port is
+  the output port, all others are inputs.
+
+Example:
+
+syscon {
+	compatible = "syscon", "simple-mfd";
+
+	mux {
+		compatible = "video-multiplexer";
+		/* Single bit (1 << 19) in syscon register 0x04: */
+		reg = <0x04>;
+		bit-mask = <1>;
+		bit-shift = <19>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port at 0 {
+			reg = <0>;
+
+			mux_in0: endpoint {
+				remote-endpoint = <&video_source0_out>;
+			};
+		};
+
+		port at 1 {
+			reg = <1>;
+
+			mux_in1: endpoint {
+				remote-endpoint = <&video_source1_out>;
+			};
+		};
+
+		port at 2 {
+			reg = <2>;
+
+			mux_out: endpoint {
+				remote-endpoint = <&capture_interface_in>;
+			};
+		};
+	};
+};
-- 
2.7.4

[PATCH v5 01/39] [media] dt-bindings: Add bindings for video-multiplexer device

[Steve Longerbeam]

From: Philipp Zabel <p.zabel@pengutronix.de>

Add bindings documentation for the video multiplexer device.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 .../bindings/media/video-multiplexer.txt           | 59 ++++++++++++++++++++++
 1 file changed, 59 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/video-multiplexer.txt

diff --git a/Documentation/devicetree/bindings/media/video-multiplexer.txt b/Documentation/devicetree/bindings/media/video-multiplexer.txt
new file mode 100644
index 0000000..9d133d9
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/video-multiplexer.txt
@@ -0,0 +1,59 @@
+Video Multiplexer
+=================
+
+Video multiplexers allow to select between multiple input ports. Video received
+on the active input port is passed through to the output port. Muxes described
+by this binding may be controlled by a syscon register bitfield or by a GPIO.
+
+Required properties:
+- compatible : should be "video-multiplexer"
+- reg: should be register base of the register containing the control bitfield
+- bit-mask: bitmask of the control bitfield in the control register
+- bit-shift: bit offset of the control bitfield in the control register
+- gpios: alternatively to reg, bit-mask, and bit-shift, a single GPIO phandle
+  may be given to switch between two inputs
+- #address-cells: should be <1>
+- #size-cells: should be <0>
+- port@*: at least three port nodes containing endpoints connecting to the
+  source and sink devices according to of_graph bindings. The last port is
+  the output port, all others are inputs.
+
+Example:
+
+syscon {
+	compatible = "syscon", "simple-mfd";
+
+	mux {
+		compatible = "video-multiplexer";
+		/* Single bit (1 << 19) in syscon register 0x04: */
+		reg = <0x04>;
+		bit-mask = <1>;
+		bit-shift = <19>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			mux_in0: endpoint {
+				remote-endpoint = <&video_source0_out>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			mux_in1: endpoint {
+				remote-endpoint = <&video_source1_out>;
+			};
+		};
+
+		port@2 {
+			reg = <2>;
+
+			mux_out: endpoint {
+				remote-endpoint = <&capture_interface_in>;
+			};
+		};
+	};
+};
-- 
2.7.4

Re: [PATCH v5 01/39] [media] dt-bindings: Add bindings for video-multiplexer device

[Rob Herring]

On Thu, Mar 09, 2017 at 08:52:41PM -0800, Steve Longerbeam wrote:
> From: Philipp Zabel <p.zabel@pengutronix.de>
> 
> Add bindings documentation for the video multiplexer device.
> 
> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> ---
>  .../bindings/media/video-multiplexer.txt           | 59 ++++++++++++++++++++++
>  1 file changed, 59 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/video-multiplexer.txt

Acked-by: Rob Herring <robh@kernel.org>

[PATCH v5 01/39] [media] dt-bindings: Add bindings for video-multiplexer device

[Rob Herring]

On Thu, Mar 09, 2017 at 08:52:41PM -0800, Steve Longerbeam wrote:
> From: Philipp Zabel <p.zabel@pengutronix.de>
> 
> Add bindings documentation for the video multiplexer device.
> 
> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> ---
>  .../bindings/media/video-multiplexer.txt           | 59 ++++++++++++++++++++++
>  1 file changed, 59 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/video-multiplexer.txt

Acked-by: Rob Herring <robh@kernel.org>

Re: [PATCH v5 01/39] [media] dt-bindings: Add bindings for video-multiplexer device

[Rob Herring]

On Thu, Mar 09, 2017 at 08:52:41PM -0800, Steve Longerbeam wrote:
> From: Philipp Zabel <p.zabel@pengutronix.de>
> 
> Add bindings documentation for the video multiplexer device.
> 
> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> ---
>  .../bindings/media/video-multiplexer.txt           | 59 ++++++++++++++++++++++
>  1 file changed, 59 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/video-multiplexer.txt

Acked-by: Rob Herring <robh@kernel.org>

[PATCH v5 02/39] [media] dt-bindings: Add bindings for i.MX media driver

[Steve Longerbeam]

Add bindings documentation for the i.MX media driver.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 Documentation/devicetree/bindings/media/imx.txt | 74 +++++++++++++++++++++++++
 1 file changed, 74 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/imx.txt

diff --git a/Documentation/devicetree/bindings/media/imx.txt b/Documentation/devicetree/bindings/media/imx.txt
new file mode 100644
index 0000000..3059c06
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/imx.txt
@@ -0,0 +1,74 @@
+Freescale i.MX Media Video Device
+=================================
+
+Video Media Controller node
+---------------------------
+
+This is the media controller node for video capture support. It is a
+virtual device that lists the camera serial interface nodes that the
+media device will control.
+
+Required properties:
+- compatible : "fsl,imx-capture-subsystem";
+- ports      : Should contain a list of phandles pointing to camera
+		sensor interface ports of IPU devices
+
+example:
+
+capture-subsystem {
+	compatible = "fsl,imx-capture-subsystem";
+	ports = <&ipu1_csi0>, <&ipu1_csi1>;
+};
+
+fim child node
+--------------
+
+This is an optional child node of the ipu_csi port nodes. If present and
+available, it enables the Frame Interval Monitor. Its properties can be
+used to modify the method in which the FIM measures frame intervals.
+Refer to Documentation/media/v4l-drivers/imx.rst for more info on the
+Frame Interval Monitor.
+
+Optional properties:
+- fsl,input-capture-channel: an input capture channel and channel flags,
+			     specified as <chan flags>. The channel number
+			     must be 0 or 1. The flags can be
+			     IRQ_TYPE_EDGE_RISING, IRQ_TYPE_EDGE_FALLING, or
+			     IRQ_TYPE_EDGE_BOTH, and specify which input
+			     capture signal edge will trigger the input
+			     capture event. If an input capture channel is
+			     specified, the FIM will use this method to
+			     measure frame intervals instead of via the EOF
+			     interrupt. The input capture method is much
+			     preferred over EOF as it is not subject to
+			     interrupt latency errors. However it requires
+			     routing the VSYNC or FIELD output signals of
+			     the camera sensor to one of the i.MX input
+			     capture pads (SD1_DAT0, SD1_DAT1), which also
+			     gives up support for SD1.
+
+
+mipi_csi2 node
+--------------
+
+This is the device node for the MIPI CSI-2 Receiver, required for MIPI
+CSI-2 sensors.
+
+Required properties:
+- compatible	: "fsl,imx6-mipi-csi2", "snps,dw-mipi-csi2";
+- reg           : physical base address and length of the register set;
+- clocks	: the MIPI CSI-2 receiver requires three clocks: hsi_tx
+		  (the D-PHY clock), video_27m (D-PHY PLL reference
+		  clock), and eim_podf;
+- clock-names	: must contain "dphy", "ref", "pix";
+- port@*        : five port nodes must exist, containing endpoints
+		  connecting to the source and sink devices according to
+		  of_graph bindings. The first port is an input port,
+		  connecting with a MIPI CSI-2 source, and ports 1
+		  through 4 are output ports connecting with parallel
+		  bus sink endpoint nodes and correspond to the four
+		  MIPI CSI-2 virtual channel outputs.
+
+Optional properties:
+- interrupts	: must contain two level-triggered interrupts,
+		  in order: 100 and 101;
-- 
2.7.4

[PATCH v5 02/39] [media] dt-bindings: Add bindings for i.MX media driver

[Steve Longerbeam]

Add bindings documentation for the i.MX media driver.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 Documentation/devicetree/bindings/media/imx.txt | 74 +++++++++++++++++++++++++
 1 file changed, 74 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/imx.txt

diff --git a/Documentation/devicetree/bindings/media/imx.txt b/Documentation/devicetree/bindings/media/imx.txt
new file mode 100644
index 0000000..3059c06
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/imx.txt
@@ -0,0 +1,74 @@
+Freescale i.MX Media Video Device
+=================================
+
+Video Media Controller node
+---------------------------
+
+This is the media controller node for video capture support. It is a
+virtual device that lists the camera serial interface nodes that the
+media device will control.
+
+Required properties:
+- compatible : "fsl,imx-capture-subsystem";
+- ports      : Should contain a list of phandles pointing to camera
+		sensor interface ports of IPU devices
+
+example:
+
+capture-subsystem {
+	compatible = "fsl,imx-capture-subsystem";
+	ports = <&ipu1_csi0>, <&ipu1_csi1>;
+};
+
+fim child node
+--------------
+
+This is an optional child node of the ipu_csi port nodes. If present and
+available, it enables the Frame Interval Monitor. Its properties can be
+used to modify the method in which the FIM measures frame intervals.
+Refer to Documentation/media/v4l-drivers/imx.rst for more info on the
+Frame Interval Monitor.
+
+Optional properties:
+- fsl,input-capture-channel: an input capture channel and channel flags,
+			     specified as <chan flags>. The channel number
+			     must be 0 or 1. The flags can be
+			     IRQ_TYPE_EDGE_RISING, IRQ_TYPE_EDGE_FALLING, or
+			     IRQ_TYPE_EDGE_BOTH, and specify which input
+			     capture signal edge will trigger the input
+			     capture event. If an input capture channel is
+			     specified, the FIM will use this method to
+			     measure frame intervals instead of via the EOF
+			     interrupt. The input capture method is much
+			     preferred over EOF as it is not subject to
+			     interrupt latency errors. However it requires
+			     routing the VSYNC or FIELD output signals of
+			     the camera sensor to one of the i.MX input
+			     capture pads (SD1_DAT0, SD1_DAT1), which also
+			     gives up support for SD1.
+
+
+mipi_csi2 node
+--------------
+
+This is the device node for the MIPI CSI-2 Receiver, required for MIPI
+CSI-2 sensors.
+
+Required properties:
+- compatible	: "fsl,imx6-mipi-csi2", "snps,dw-mipi-csi2";
+- reg           : physical base address and length of the register set;
+- clocks	: the MIPI CSI-2 receiver requires three clocks: hsi_tx
+		  (the D-PHY clock), video_27m (D-PHY PLL reference
+		  clock), and eim_podf;
+- clock-names	: must contain "dphy", "ref", "pix";
+- port@*        : five port nodes must exist, containing endpoints
+		  connecting to the source and sink devices according to
+		  of_graph bindings. The first port is an input port,
+		  connecting with a MIPI CSI-2 source, and ports 1
+		  through 4 are output ports connecting with parallel
+		  bus sink endpoint nodes and correspond to the four
+		  MIPI CSI-2 virtual channel outputs.
+
+Optional properties:
+- interrupts	: must contain two level-triggered interrupts,
+		  in order: 100 and 101;
-- 
2.7.4

[PATCH v5 02/39] [media] dt-bindings: Add bindings for i.MX media driver

[Steve Longerbeam]

Add bindings documentation for the i.MX media driver.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 Documentation/devicetree/bindings/media/imx.txt | 74 +++++++++++++++++++++++++
 1 file changed, 74 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/imx.txt

diff --git a/Documentation/devicetree/bindings/media/imx.txt b/Documentation/devicetree/bindings/media/imx.txt
new file mode 100644
index 0000000..3059c06
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/imx.txt
@@ -0,0 +1,74 @@
+Freescale i.MX Media Video Device
+=================================
+
+Video Media Controller node
+---------------------------
+
+This is the media controller node for video capture support. It is a
+virtual device that lists the camera serial interface nodes that the
+media device will control.
+
+Required properties:
+- compatible : "fsl,imx-capture-subsystem";
+- ports      : Should contain a list of phandles pointing to camera
+		sensor interface ports of IPU devices
+
+example:
+
+capture-subsystem {
+	compatible = "fsl,imx-capture-subsystem";
+	ports = <&ipu1_csi0>, <&ipu1_csi1>;
+};
+
+fim child node
+--------------
+
+This is an optional child node of the ipu_csi port nodes. If present and
+available, it enables the Frame Interval Monitor. Its properties can be
+used to modify the method in which the FIM measures frame intervals.
+Refer to Documentation/media/v4l-drivers/imx.rst for more info on the
+Frame Interval Monitor.
+
+Optional properties:
+- fsl,input-capture-channel: an input capture channel and channel flags,
+			     specified as <chan flags>. The channel number
+			     must be 0 or 1. The flags can be
+			     IRQ_TYPE_EDGE_RISING, IRQ_TYPE_EDGE_FALLING, or
+			     IRQ_TYPE_EDGE_BOTH, and specify which input
+			     capture signal edge will trigger the input
+			     capture event. If an input capture channel is
+			     specified, the FIM will use this method to
+			     measure frame intervals instead of via the EOF
+			     interrupt. The input capture method is much
+			     preferred over EOF as it is not subject to
+			     interrupt latency errors. However it requires
+			     routing the VSYNC or FIELD output signals of
+			     the camera sensor to one of the i.MX input
+			     capture pads (SD1_DAT0, SD1_DAT1), which also
+			     gives up support for SD1.
+
+
+mipi_csi2 node
+--------------
+
+This is the device node for the MIPI CSI-2 Receiver, required for MIPI
+CSI-2 sensors.
+
+Required properties:
+- compatible	: "fsl,imx6-mipi-csi2", "snps,dw-mipi-csi2";
+- reg           : physical base address and length of the register set;
+- clocks	: the MIPI CSI-2 receiver requires three clocks: hsi_tx
+		  (the D-PHY clock), video_27m (D-PHY PLL reference
+		  clock), and eim_podf;
+- clock-names	: must contain "dphy", "ref", "pix";
+- port@*        : five port nodes must exist, containing endpoints
+		  connecting to the source and sink devices according to
+		  of_graph bindings. The first port is an input port,
+		  connecting with a MIPI CSI-2 source, and ports 1
+		  through 4 are output ports connecting with parallel
+		  bus sink endpoint nodes and correspond to the four
+		  MIPI CSI-2 virtual channel outputs.
+
+Optional properties:
+- interrupts	: must contain two level-triggered interrupts,
+		  in order: 100 and 101;
-- 
2.7.4

Re: [PATCH v5 02/39] [media] dt-bindings: Add bindings for i.MX media driver

[Rob Herring]

+Ramiro

On Thu, Mar 09, 2017 at 08:52:42PM -0800, Steve Longerbeam wrote:
> Add bindings documentation for the i.MX media driver.
> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> ---
>  Documentation/devicetree/bindings/media/imx.txt | 74 +++++++++++++++++++++++++
>  1 file changed, 74 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/imx.txt
> 
> diff --git a/Documentation/devicetree/bindings/media/imx.txt b/Documentation/devicetree/bindings/media/imx.txt
> new file mode 100644
> index 0000000..3059c06
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/imx.txt
> @@ -0,0 +1,74 @@
> +Freescale i.MX Media Video Device
> +=================================
> +
> +Video Media Controller node
> +---------------------------
> +
> +This is the media controller node for video capture support. It is a
> +virtual device that lists the camera serial interface nodes that the
> +media device will control.
> +
> +Required properties:
> +- compatible : "fsl,imx-capture-subsystem";
> +- ports      : Should contain a list of phandles pointing to camera
> +		sensor interface ports of IPU devices
> +
> +example:
> +
> +capture-subsystem {
> +	compatible = "fsl,imx-capture-subsystem";
> +	ports = <&ipu1_csi0>, <&ipu1_csi1>;
> +};
> +
> +fim child node
> +--------------
> +
> +This is an optional child node of the ipu_csi port nodes. If present and
> +available, it enables the Frame Interval Monitor. Its properties can be
> +used to modify the method in which the FIM measures frame intervals.
> +Refer to Documentation/media/v4l-drivers/imx.rst for more info on the
> +Frame Interval Monitor.
> +
> +Optional properties:
> +- fsl,input-capture-channel: an input capture channel and channel flags,
> +			     specified as <chan flags>. The channel number
> +			     must be 0 or 1. The flags can be
> +			     IRQ_TYPE_EDGE_RISING, IRQ_TYPE_EDGE_FALLING, or
> +			     IRQ_TYPE_EDGE_BOTH, and specify which input
> +			     capture signal edge will trigger the input
> +			     capture event. If an input capture channel is
> +			     specified, the FIM will use this method to
> +			     measure frame intervals instead of via the EOF
> +			     interrupt. The input capture method is much
> +			     preferred over EOF as it is not subject to
> +			     interrupt latency errors. However it requires
> +			     routing the VSYNC or FIELD output signals of
> +			     the camera sensor to one of the i.MX input
> +			     capture pads (SD1_DAT0, SD1_DAT1), which also
> +			     gives up support for SD1.
> +
> +
> +mipi_csi2 node
> +--------------
> +
> +This is the device node for the MIPI CSI-2 Receiver, required for MIPI
> +CSI-2 sensors.
> +
> +Required properties:
> +- compatible	: "fsl,imx6-mipi-csi2", "snps,dw-mipi-csi2";

Ramiro is also working on a binding for DW MIPI CSI2 block[1]. We need 1 
binding for that.

> +- reg           : physical base address and length of the register set;
> +- clocks	: the MIPI CSI-2 receiver requires three clocks: hsi_tx
> +		  (the D-PHY clock), video_27m (D-PHY PLL reference
> +		  clock), and eim_podf;
> +- clock-names	: must contain "dphy", "ref", "pix";
> +- port@*        : five port nodes must exist, containing endpoints
> +		  connecting to the source and sink devices according to
> +		  of_graph bindings. The first port is an input port,
> +		  connecting with a MIPI CSI-2 source, and ports 1
> +		  through 4 are output ports connecting with parallel
> +		  bus sink endpoint nodes and correspond to the four
> +		  MIPI CSI-2 virtual channel outputs.
> +
> +Optional properties:
> +- interrupts	: must contain two level-triggered interrupts,
> +		  in order: 100 and 101;
> -- 
> 2.7.4
> 

[1] https://lkml.org/lkml/2017/3/7/395

[PATCH v5 02/39] [media] dt-bindings: Add bindings for i.MX media driver

[Rob Herring]

+Ramiro

On Thu, Mar 09, 2017 at 08:52:42PM -0800, Steve Longerbeam wrote:
> Add bindings documentation for the i.MX media driver.
> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> ---
>  Documentation/devicetree/bindings/media/imx.txt | 74 +++++++++++++++++++++++++
>  1 file changed, 74 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/imx.txt
> 
> diff --git a/Documentation/devicetree/bindings/media/imx.txt b/Documentation/devicetree/bindings/media/imx.txt
> new file mode 100644
> index 0000000..3059c06
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/imx.txt
> @@ -0,0 +1,74 @@
> +Freescale i.MX Media Video Device
> +=================================
> +
> +Video Media Controller node
> +---------------------------
> +
> +This is the media controller node for video capture support. It is a
> +virtual device that lists the camera serial interface nodes that the
> +media device will control.
> +
> +Required properties:
> +- compatible : "fsl,imx-capture-subsystem";
> +- ports      : Should contain a list of phandles pointing to camera
> +		sensor interface ports of IPU devices
> +
> +example:
> +
> +capture-subsystem {
> +	compatible = "fsl,imx-capture-subsystem";
> +	ports = <&ipu1_csi0>, <&ipu1_csi1>;
> +};
> +
> +fim child node
> +--------------
> +
> +This is an optional child node of the ipu_csi port nodes. If present and
> +available, it enables the Frame Interval Monitor. Its properties can be
> +used to modify the method in which the FIM measures frame intervals.
> +Refer to Documentation/media/v4l-drivers/imx.rst for more info on the
> +Frame Interval Monitor.
> +
> +Optional properties:
> +- fsl,input-capture-channel: an input capture channel and channel flags,
> +			     specified as <chan flags>. The channel number
> +			     must be 0 or 1. The flags can be
> +			     IRQ_TYPE_EDGE_RISING, IRQ_TYPE_EDGE_FALLING, or
> +			     IRQ_TYPE_EDGE_BOTH, and specify which input
> +			     capture signal edge will trigger the input
> +			     capture event. If an input capture channel is
> +			     specified, the FIM will use this method to
> +			     measure frame intervals instead of via the EOF
> +			     interrupt. The input capture method is much
> +			     preferred over EOF as it is not subject to
> +			     interrupt latency errors. However it requires
> +			     routing the VSYNC or FIELD output signals of
> +			     the camera sensor to one of the i.MX input
> +			     capture pads (SD1_DAT0, SD1_DAT1), which also
> +			     gives up support for SD1.
> +
> +
> +mipi_csi2 node
> +--------------
> +
> +This is the device node for the MIPI CSI-2 Receiver, required for MIPI
> +CSI-2 sensors.
> +
> +Required properties:
> +- compatible	: "fsl,imx6-mipi-csi2", "snps,dw-mipi-csi2";

Ramiro is also working on a binding for DW MIPI CSI2 block[1]. We need 1 
binding for that.

> +- reg           : physical base address and length of the register set;
> +- clocks	: the MIPI CSI-2 receiver requires three clocks: hsi_tx
> +		  (the D-PHY clock), video_27m (D-PHY PLL reference
> +		  clock), and eim_podf;
> +- clock-names	: must contain "dphy", "ref", "pix";
> +- port@*        : five port nodes must exist, containing endpoints
> +		  connecting to the source and sink devices according to
> +		  of_graph bindings. The first port is an input port,
> +		  connecting with a MIPI CSI-2 source, and ports 1
> +		  through 4 are output ports connecting with parallel
> +		  bus sink endpoint nodes and correspond to the four
> +		  MIPI CSI-2 virtual channel outputs.
> +
> +Optional properties:
> +- interrupts	: must contain two level-triggered interrupts,
> +		  in order: 100 and 101;
> -- 
> 2.7.4
> 

[1] https://lkml.org/lkml/2017/3/7/395

Re: [PATCH v5 02/39] [media] dt-bindings: Add bindings for i.MX media driver

[Rob Herring]

+Ramiro

On Thu, Mar 09, 2017 at 08:52:42PM -0800, Steve Longerbeam wrote:
> Add bindings documentation for the i.MX media driver.
> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> ---
>  Documentation/devicetree/bindings/media/imx.txt | 74 +++++++++++++++++++++++++
>  1 file changed, 74 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/imx.txt
> 
> diff --git a/Documentation/devicetree/bindings/media/imx.txt b/Documentation/devicetree/bindings/media/imx.txt
> new file mode 100644
> index 0000000..3059c06
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/imx.txt
> @@ -0,0 +1,74 @@
> +Freescale i.MX Media Video Device
> +=================================
> +
> +Video Media Controller node
> +---------------------------
> +
> +This is the media controller node for video capture support. It is a
> +virtual device that lists the camera serial interface nodes that the
> +media device will control.
> +
> +Required properties:
> +- compatible : "fsl,imx-capture-subsystem";
> +- ports      : Should contain a list of phandles pointing to camera
> +		sensor interface ports of IPU devices
> +
> +example:
> +
> +capture-subsystem {
> +	compatible = "fsl,imx-capture-subsystem";
> +	ports = <&ipu1_csi0>, <&ipu1_csi1>;
> +};
> +
> +fim child node
> +--------------
> +
> +This is an optional child node of the ipu_csi port nodes. If present and
> +available, it enables the Frame Interval Monitor. Its properties can be
> +used to modify the method in which the FIM measures frame intervals.
> +Refer to Documentation/media/v4l-drivers/imx.rst for more info on the
> +Frame Interval Monitor.
> +
> +Optional properties:
> +- fsl,input-capture-channel: an input capture channel and channel flags,
> +			     specified as <chan flags>. The channel number
> +			     must be 0 or 1. The flags can be
> +			     IRQ_TYPE_EDGE_RISING, IRQ_TYPE_EDGE_FALLING, or
> +			     IRQ_TYPE_EDGE_BOTH, and specify which input
> +			     capture signal edge will trigger the input
> +			     capture event. If an input capture channel is
> +			     specified, the FIM will use this method to
> +			     measure frame intervals instead of via the EOF
> +			     interrupt. The input capture method is much
> +			     preferred over EOF as it is not subject to
> +			     interrupt latency errors. However it requires
> +			     routing the VSYNC or FIELD output signals of
> +			     the camera sensor to one of the i.MX input
> +			     capture pads (SD1_DAT0, SD1_DAT1), which also
> +			     gives up support for SD1.
> +
> +
> +mipi_csi2 node
> +--------------
> +
> +This is the device node for the MIPI CSI-2 Receiver, required for MIPI
> +CSI-2 sensors.
> +
> +Required properties:
> +- compatible	: "fsl,imx6-mipi-csi2", "snps,dw-mipi-csi2";

Ramiro is also working on a binding for DW MIPI CSI2 block[1]. We need 1 
binding for that.

> +- reg           : physical base address and length of the register set;
> +- clocks	: the MIPI CSI-2 receiver requires three clocks: hsi_tx
> +		  (the D-PHY clock), video_27m (D-PHY PLL reference
> +		  clock), and eim_podf;
> +- clock-names	: must contain "dphy", "ref", "pix";
> +- port@*        : five port nodes must exist, containing endpoints
> +		  connecting to the source and sink devices according to
> +		  of_graph bindings. The first port is an input port,
> +		  connecting with a MIPI CSI-2 source, and ports 1
> +		  through 4 are output ports connecting with parallel
> +		  bus sink endpoint nodes and correspond to the four
> +		  MIPI CSI-2 virtual channel outputs.
> +
> +Optional properties:
> +- interrupts	: must contain two level-triggered interrupts,
> +		  in order: 100 and 101;
> -- 
> 2.7.4
> 

[1] https://lkml.org/lkml/2017/3/7/395

[PATCH v5 03/39] [media] dt/bindings: Add bindings for OV5640

[Steve Longerbeam]

Add device tree binding documentation for the OV5640 camera sensor.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 .../devicetree/bindings/media/i2c/ov5640.txt       | 45 ++++++++++++++++++++++
 1 file changed, 45 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/ov5640.txt

diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.txt b/Documentation/devicetree/bindings/media/i2c/ov5640.txt
new file mode 100644
index 0000000..540b36c
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov5640.txt
@@ -0,0 +1,45 @@
+* Omnivision OV5640 MIPI CSI-2 sensor
+
+Required Properties:
+- compatible: should be "ovti,ov5640"
+- clocks: reference to the xclk input clock.
+- clock-names: should be "xclk".
+- DOVDD-supply: Digital I/O voltage supply, 1.8 volts
+- AVDD-supply: Analog voltage supply, 2.8 volts
+- DVDD-supply: Digital core voltage supply, 1.5 volts
+
+Optional Properties:
+- reset-gpios: reference to the GPIO connected to the reset pin, if any.
+	       This is an active low signal to the OV5640.
+- powerdown-gpios: reference to the GPIO connected to the powerdown pin,
+		   if any. This is an active high signal to the OV5640.
+
+The device node must contain one 'port' child node for its digital output
+video port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+&i2c1 {
+	ov5640: camera@3c {
+		compatible = "ovti,ov5640";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5640>;
+		reg = <0x3c>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		clock-names = "xclk";
+		DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+		AVDD-supply = <&vgen3_reg>;  /* 2.8v */
+		DVDD-supply = <&vgen2_reg>;  /* 1.5v */
+		powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+
+		port {
+			ov5640_to_mipi_csi2: endpoint {
+				remote-endpoint = <&mipi_csi2_from_ov5640>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+};
-- 
2.7.4

[PATCH v5 03/39] [media] dt/bindings: Add bindings for OV5640

[Steve Longerbeam]

Add device tree binding documentation for the OV5640 camera sensor.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 .../devicetree/bindings/media/i2c/ov5640.txt       | 45 ++++++++++++++++++++++
 1 file changed, 45 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/ov5640.txt

diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.txt b/Documentation/devicetree/bindings/media/i2c/ov5640.txt
new file mode 100644
index 0000000..540b36c
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov5640.txt
@@ -0,0 +1,45 @@
+* Omnivision OV5640 MIPI CSI-2 sensor
+
+Required Properties:
+- compatible: should be "ovti,ov5640"
+- clocks: reference to the xclk input clock.
+- clock-names: should be "xclk".
+- DOVDD-supply: Digital I/O voltage supply, 1.8 volts
+- AVDD-supply: Analog voltage supply, 2.8 volts
+- DVDD-supply: Digital core voltage supply, 1.5 volts
+
+Optional Properties:
+- reset-gpios: reference to the GPIO connected to the reset pin, if any.
+	       This is an active low signal to the OV5640.
+- powerdown-gpios: reference to the GPIO connected to the powerdown pin,
+		   if any. This is an active high signal to the OV5640.
+
+The device node must contain one 'port' child node for its digital output
+video port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+&i2c1 {
+	ov5640: camera at 3c {
+		compatible = "ovti,ov5640";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5640>;
+		reg = <0x3c>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		clock-names = "xclk";
+		DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+		AVDD-supply = <&vgen3_reg>;  /* 2.8v */
+		DVDD-supply = <&vgen2_reg>;  /* 1.5v */
+		powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+
+		port {
+			ov5640_to_mipi_csi2: endpoint {
+				remote-endpoint = <&mipi_csi2_from_ov5640>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+};
-- 
2.7.4

[PATCH v5 03/39] [media] dt/bindings: Add bindings for OV5640

[Steve Longerbeam]

Add device tree binding documentation for the OV5640 camera sensor.

Signed-off-by: Steve Longerbeam <steve_longerbeam-nmGgyN9QBj3QT0dZR+AlfA@public.gmane.org>
---
 .../devicetree/bindings/media/i2c/ov5640.txt       | 45 ++++++++++++++++++++++
 1 file changed, 45 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/ov5640.txt

diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.txt b/Documentation/devicetree/bindings/media/i2c/ov5640.txt
new file mode 100644
index 0000000..540b36c
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov5640.txt
@@ -0,0 +1,45 @@
+* Omnivision OV5640 MIPI CSI-2 sensor
+
+Required Properties:
+- compatible: should be "ovti,ov5640"
+- clocks: reference to the xclk input clock.
+- clock-names: should be "xclk".
+- DOVDD-supply: Digital I/O voltage supply, 1.8 volts
+- AVDD-supply: Analog voltage supply, 2.8 volts
+- DVDD-supply: Digital core voltage supply, 1.5 volts
+
+Optional Properties:
+- reset-gpios: reference to the GPIO connected to the reset pin, if any.
+	       This is an active low signal to the OV5640.
+- powerdown-gpios: reference to the GPIO connected to the powerdown pin,
+		   if any. This is an active high signal to the OV5640.
+
+The device node must contain one 'port' child node for its digital output
+video port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+&i2c1 {
+	ov5640: camera@3c {
+		compatible = "ovti,ov5640";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5640>;
+		reg = <0x3c>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		clock-names = "xclk";
+		DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+		AVDD-supply = <&vgen3_reg>;  /* 2.8v */
+		DVDD-supply = <&vgen2_reg>;  /* 1.5v */
+		powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+
+		port {
+			ov5640_to_mipi_csi2: endpoint {
+				remote-endpoint = <&mipi_csi2_from_ov5640>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+};
-- 
2.7.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 03/39] [media] dt/bindings: Add bindings for OV5640

[Rob Herring]

On Thu, Mar 09, 2017 at 08:52:43PM -0800, Steve Longerbeam wrote:
> Add device tree binding documentation for the OV5640 camera sensor.
> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> ---
>  .../devicetree/bindings/media/i2c/ov5640.txt       | 45 ++++++++++++++++++++++
>  1 file changed, 45 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/ov5640.txt

Acked-by: Rob Herring <robh@kernel.org>

[PATCH v5 03/39] [media] dt/bindings: Add bindings for OV5640

[Rob Herring]

On Thu, Mar 09, 2017 at 08:52:43PM -0800, Steve Longerbeam wrote:
> Add device tree binding documentation for the OV5640 camera sensor.
> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> ---
>  .../devicetree/bindings/media/i2c/ov5640.txt       | 45 ++++++++++++++++++++++
>  1 file changed, 45 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/ov5640.txt

Acked-by: Rob Herring <robh@kernel.org>

Re: [PATCH v5 03/39] [media] dt/bindings: Add bindings for OV5640

[Rob Herring]

On Thu, Mar 09, 2017 at 08:52:43PM -0800, Steve Longerbeam wrote:
> Add device tree binding documentation for the OV5640 camera sensor.
> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> ---
>  .../devicetree/bindings/media/i2c/ov5640.txt       | 45 ++++++++++++++++++++++
>  1 file changed, 45 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/ov5640.txt

Acked-by: Rob Herring <robh@kernel.org>

[PATCH v5 04/39] ARM: dts: imx6qdl: Add compatible, clocks, irqs to MIPI CSI-2 node

[Steve Longerbeam]

Add to the MIPI CSI2 receiver node: compatible strings,
interrupt sources, and clocks.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6qdl.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi
index 6d7bf64..d28a413 100644
--- a/arch/arm/boot/dts/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/imx6qdl.dtsi
@@ -1134,7 +1134,14 @@
 			};
 
 			mipi_csi: mipi@021dc000 {
+				compatible = "fsl,imx6-mipi-csi2", "snps,dw-mipi-csi2";
 				reg = <0x021dc000 0x4000>;
+				interrupts = <0 100 0x04>, <0 101 0x04>;
+				clocks = <&clks IMX6QDL_CLK_HSI_TX>,
+					 <&clks IMX6QDL_CLK_VIDEO_27M>,
+					 <&clks IMX6QDL_CLK_EIM_PODF>;
+				clock-names = "dphy", "ref", "pix";
+				status = "disabled";
 			};
 
 			mipi_dsi: mipi@021e0000 {
-- 
2.7.4

[PATCH v5 04/39] ARM: dts: imx6qdl: Add compatible, clocks, irqs to MIPI CSI-2 node

[Steve Longerbeam]

Add to the MIPI CSI2 receiver node: compatible strings,
interrupt sources, and clocks.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6qdl.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi
index 6d7bf64..d28a413 100644
--- a/arch/arm/boot/dts/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/imx6qdl.dtsi
@@ -1134,7 +1134,14 @@
 			};
 
 			mipi_csi: mipi at 021dc000 {
+				compatible = "fsl,imx6-mipi-csi2", "snps,dw-mipi-csi2";
 				reg = <0x021dc000 0x4000>;
+				interrupts = <0 100 0x04>, <0 101 0x04>;
+				clocks = <&clks IMX6QDL_CLK_HSI_TX>,
+					 <&clks IMX6QDL_CLK_VIDEO_27M>,
+					 <&clks IMX6QDL_CLK_EIM_PODF>;
+				clock-names = "dphy", "ref", "pix";
+				status = "disabled";
 			};
 
 			mipi_dsi: mipi at 021e0000 {
-- 
2.7.4

[PATCH v5 04/39] ARM: dts: imx6qdl: Add compatible, clocks, irqs to MIPI CSI-2 node

[Steve Longerbeam]

Add to the MIPI CSI2 receiver node: compatible strings,
interrupt sources, and clocks.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6qdl.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi
index 6d7bf64..d28a413 100644
--- a/arch/arm/boot/dts/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/imx6qdl.dtsi
@@ -1134,7 +1134,14 @@
 			};
 
 			mipi_csi: mipi@021dc000 {
+				compatible = "fsl,imx6-mipi-csi2", "snps,dw-mipi-csi2";
 				reg = <0x021dc000 0x4000>;
+				interrupts = <0 100 0x04>, <0 101 0x04>;
+				clocks = <&clks IMX6QDL_CLK_HSI_TX>,
+					 <&clks IMX6QDL_CLK_VIDEO_27M>,
+					 <&clks IMX6QDL_CLK_EIM_PODF>;
+				clock-names = "dphy", "ref", "pix";
+				status = "disabled";
 			};
 
 			mipi_dsi: mipi@021e0000 {
-- 
2.7.4

[PATCH v5 05/39] ARM: dts: imx6qdl: Add mipi_ipu1/2 multiplexers, mipi_csi, and their connections

[Steve Longerbeam]

From: Philipp Zabel <p.zabel@pengutronix.de>

This patch adds the device tree graph connecting the input multiplexers
to the IPU CSIs and the MIPI-CSI2 gasket on i.MX6. The MIPI_IPU
multiplexers are added as children of the iomuxc-gpr syscon device node.
On i.MX6Q/D two two-input multiplexers in front of IPU1 CSI0 and IPU2
CSI1 allow to select between CSI0/1 parallel input pads and the MIPI
CSI-2 virtual channels 0/3.
On i.MX6DL/S two five-input multiplexers in front of IPU1 CSI0 and IPU1
CSI1 allow to select between CSI0/1 parallel input pads and any of the
four MIPI CSI-2 virtual channels.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>

--

- Removed some dangling/unused endpoints (ipu2_csi0_from_csi2ipu)
- Renamed the mipi virtual channel endpoint labels, from "mipi_csiX_..."
  to "mipi_vcX...".
- Added input endpoint anchors to the video muxes for the connections
  from parallel sensors.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6dl.dtsi  | 180 +++++++++++++++++++++++++++++++++++++++++
 arch/arm/boot/dts/imx6q.dtsi   | 116 ++++++++++++++++++++++++++
 arch/arm/boot/dts/imx6qdl.dtsi |  10 ++-
 3 files changed, 305 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6dl.dtsi b/arch/arm/boot/dts/imx6dl.dtsi
index 7aa120f..8958c4a 100644
--- a/arch/arm/boot/dts/imx6dl.dtsi
+++ b/arch/arm/boot/dts/imx6dl.dtsi
@@ -181,6 +181,186 @@
 		      "di0", "di1";
 };
 
+&gpr {
+	ipu1_csi0_mux: ipu1_csi0_mux@34 {
+		compatible = "video-multiplexer";
+		reg = <0x34>;
+		bit-mask = <0x7>;
+		bit-shift = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		port@0 {
+			reg = <0>;
+
+			ipu1_csi0_mux_from_mipi_vc0: endpoint {
+				remote-endpoint = <&mipi_vc0_to_ipu1_csi0_mux>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			ipu1_csi0_mux_from_mipi_vc1: endpoint {
+				remote-endpoint = <&mipi_vc1_to_ipu1_csi0_mux>;
+			};
+		};
+
+		port@2 {
+			reg = <2>;
+
+			ipu1_csi0_mux_from_mipi_vc2: endpoint {
+				remote-endpoint = <&mipi_vc2_to_ipu1_csi0_mux>;
+			};
+		};
+
+		port@3 {
+			reg = <3>;
+
+			ipu1_csi0_mux_from_mipi_vc3: endpoint {
+				remote-endpoint = <&mipi_vc3_to_ipu1_csi0_mux>;
+			};
+		};
+
+		port@4 {
+			reg = <4>;
+
+			ipu1_csi0_mux_from_parallel_sensor: endpoint {
+			};
+		};
+
+		port@5 {
+			reg = <5>;
+
+			ipu1_csi0_mux_to_ipu1_csi0: endpoint {
+				remote-endpoint = <&ipu1_csi0_from_ipu1_csi0_mux>;
+			};
+		};
+	};
+
+	ipu1_csi1_mux: ipu1_csi1_mux@34 {
+		compatible = "video-multiplexer";
+		reg = <0x34>;
+		bit-mask = <0x7>;
+		bit-shift = <3>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		port@0 {
+			reg = <0>;
+
+			ipu1_csi1_mux_from_mipi_vc0: endpoint {
+				remote-endpoint = <&mipi_vc0_to_ipu1_csi1_mux>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			ipu1_csi1_mux_from_mipi_vc1: endpoint {
+				remote-endpoint = <&mipi_vc1_to_ipu1_csi1_mux>;
+			};
+		};
+
+		port@2 {
+			reg = <2>;
+
+			ipu1_csi1_mux_from_mipi_vc2: endpoint {
+				remote-endpoint = <&mipi_vc2_to_ipu1_csi1_mux>;
+			};
+		};
+
+		port@3 {
+			reg = <3>;
+
+			ipu1_csi1_mux_from_mipi_vc3: endpoint {
+				remote-endpoint = <&mipi_vc3_to_ipu1_csi1_mux>;
+			};
+		};
+
+		port@4 {
+			reg = <4>;
+
+			ipu1_csi1_mux_from_parallel_sensor: endpoint {
+			};
+		};
+
+		port@5 {
+			reg = <5>;
+
+			ipu1_csi1_mux_to_ipu1_csi1: endpoint {
+				remote-endpoint = <&ipu1_csi1_from_ipu1_csi1_mux>;
+			};
+		};
+	};
+};
+
+&ipu1_csi1 {
+	ipu1_csi1_from_ipu1_csi1_mux: endpoint {
+		remote-endpoint = <&ipu1_csi1_mux_to_ipu1_csi1>;
+	};
+};
+
+&mipi_csi {
+	port@1 {
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mipi_vc0_to_ipu1_csi0_mux: endpoint@0 {
+			remote-endpoint = <&ipu1_csi0_mux_from_mipi_vc0>;
+		};
+
+		mipi_vc0_to_ipu1_csi1_mux: endpoint@1 {
+			remote-endpoint = <&ipu1_csi1_mux_from_mipi_vc0>;
+		};
+	};
+
+	port@2 {
+		reg = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mipi_vc1_to_ipu1_csi0_mux: endpoint@0 {
+			remote-endpoint = <&ipu1_csi0_mux_from_mipi_vc1>;
+		};
+
+		mipi_vc1_to_ipu1_csi1_mux: endpoint@1 {
+			remote-endpoint = <&ipu1_csi1_mux_from_mipi_vc1>;
+		};
+	};
+
+	port@3 {
+		reg = <3>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mipi_vc2_to_ipu1_csi0_mux: endpoint@0 {
+			remote-endpoint = <&ipu1_csi0_mux_from_mipi_vc2>;
+		};
+
+		mipi_vc2_to_ipu1_csi1_mux: endpoint@1 {
+			remote-endpoint = <&ipu1_csi1_mux_from_mipi_vc2>;
+		};
+	};
+
+	port@4 {
+		reg = <4>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mipi_vc3_to_ipu1_csi0_mux: endpoint@0 {
+			remote-endpoint = <&ipu1_csi0_mux_from_mipi_vc3>;
+		};
+
+		mipi_vc3_to_ipu1_csi1_mux: endpoint@1 {
+			remote-endpoint = <&ipu1_csi1_mux_from_mipi_vc3>;
+		};
+	};
+};
+
 &vpu {
 	compatible = "fsl,imx6dl-vpu", "cnm,coda960";
 };
diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi
index e9a5d0b..b833b0d 100644
--- a/arch/arm/boot/dts/imx6q.dtsi
+++ b/arch/arm/boot/dts/imx6q.dtsi
@@ -143,10 +143,18 @@
 
 			ipu2_csi0: port@0 {
 				reg = <0>;
+
+				ipu2_csi0_from_mipi_vc2: endpoint {
+					remote-endpoint = <&mipi_vc2_to_ipu2_csi0>;
+				};
 			};
 
 			ipu2_csi1: port@1 {
 				reg = <1>;
+
+				ipu2_csi1_from_ipu2_csi1_mux: endpoint {
+					remote-endpoint = <&ipu2_csi1_mux_to_ipu2_csi1>;
+				};
 			};
 
 			ipu2_di0: port@2 {
@@ -266,6 +274,80 @@
 	};
 };
 
+&gpr {
+	ipu1_csi0_mux: ipu1_csi0_mux@4 {
+		compatible = "video-multiplexer";
+		reg = <0x04>;
+		bit-mask = <1>;
+		bit-shift = <19>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		port@0 {
+			reg = <0>;
+
+			ipu1_csi0_mux_from_mipi_vc0: endpoint {
+				remote-endpoint = <&mipi_vc0_to_ipu1_csi0_mux>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			ipu1_csi0_mux_from_parallel_sensor: endpoint {
+			};
+		};
+
+		port@2 {
+			reg = <2>;
+
+			ipu1_csi0_mux_to_ipu1_csi0: endpoint {
+				remote-endpoint = <&ipu1_csi0_from_ipu1_csi0_mux>;
+			};
+		};
+	};
+
+	ipu2_csi1_mux: ipu2_csi1_mux@4 {
+		compatible = "video-multiplexer";
+		reg = <0x04>;
+		bit-mask = <1>;
+		bit-shift = <20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		port@0 {
+			reg = <0>;
+
+			ipu2_csi1_mux_from_mipi_vc3: endpoint {
+				remote-endpoint = <&mipi_vc3_to_ipu2_csi1_mux>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			ipu2_csi1_mux_from_parallel_sensor: endpoint {
+			};
+		};
+
+		port@2 {
+			reg = <2>;
+
+			ipu2_csi1_mux_to_ipu2_csi1: endpoint {
+				remote-endpoint = <&ipu2_csi1_from_ipu2_csi1_mux>;
+			};
+		};
+	};
+};
+
+&ipu1_csi1 {
+	ipu1_csi1_from_mipi_vc1: endpoint {
+		remote-endpoint = <&mipi_vc1_to_ipu1_csi1>;
+	};
+};
+
 &ldb {
 	clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>, <&clks IMX6QDL_CLK_LDB_DI1_SEL>,
 		 <&clks IMX6QDL_CLK_IPU1_DI0_SEL>, <&clks IMX6QDL_CLK_IPU1_DI1_SEL>,
@@ -312,6 +394,40 @@
 	};
 };
 
+&mipi_csi {
+	port@1 {
+		reg = <1>;
+
+		mipi_vc0_to_ipu1_csi0_mux: endpoint {
+			remote-endpoint = <&ipu1_csi0_mux_from_mipi_vc0>;
+		};
+	};
+
+	port@2 {
+		reg = <2>;
+
+		mipi_vc1_to_ipu1_csi1: endpoint {
+			remote-endpoint = <&ipu1_csi1_from_mipi_vc1>;
+		};
+	};
+
+	port@3 {
+		reg = <3>;
+
+		mipi_vc2_to_ipu2_csi0: endpoint {
+			remote-endpoint = <&ipu2_csi0_from_mipi_vc2>;
+		};
+	};
+
+	port@4 {
+		reg = <4>;
+
+		mipi_vc3_to_ipu2_csi1_mux: endpoint {
+			remote-endpoint = <&ipu2_csi1_mux_from_mipi_vc3>;
+		};
+	};
+};
+
 &mipi_dsi {
 	ports {
 		port@2 {
diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi
index d28a413..194badd 100644
--- a/arch/arm/boot/dts/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/imx6qdl.dtsi
@@ -807,8 +807,10 @@
 			};
 
 			gpr: iomuxc-gpr@020e0000 {
-				compatible = "fsl,imx6q-iomuxc-gpr", "syscon";
+				compatible = "fsl,imx6q-iomuxc-gpr", "syscon", "simple-mfd";
 				reg = <0x020e0000 0x38>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 			};
 
 			iomuxc: iomuxc@020e0000 {
@@ -1136,6 +1138,8 @@
 			mipi_csi: mipi@021dc000 {
 				compatible = "fsl,imx6-mipi-csi2", "snps,dw-mipi-csi2";
 				reg = <0x021dc000 0x4000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				interrupts = <0 100 0x04>, <0 101 0x04>;
 				clocks = <&clks IMX6QDL_CLK_HSI_TX>,
 					 <&clks IMX6QDL_CLK_VIDEO_27M>,
@@ -1243,6 +1247,10 @@
 
 			ipu1_csi0: port@0 {
 				reg = <0>;
+
+				ipu1_csi0_from_ipu1_csi0_mux: endpoint {
+					remote-endpoint = <&ipu1_csi0_mux_to_ipu1_csi0>;
+				};
 			};
 
 			ipu1_csi1: port@1 {
-- 
2.7.4

[PATCH v5 05/39] ARM: dts: imx6qdl: Add mipi_ipu1/2 multiplexers, mipi_csi, and their connections

[Steve Longerbeam]

From: Philipp Zabel <p.zabel@pengutronix.de>

This patch adds the device tree graph connecting the input multiplexers
to the IPU CSIs and the MIPI-CSI2 gasket on i.MX6. The MIPI_IPU
multiplexers are added as children of the iomuxc-gpr syscon device node.
On i.MX6Q/D two two-input multiplexers in front of IPU1 CSI0 and IPU2
CSI1 allow to select between CSI0/1 parallel input pads and the MIPI
CSI-2 virtual channels 0/3.
On i.MX6DL/S two five-input multiplexers in front of IPU1 CSI0 and IPU1
CSI1 allow to select between CSI0/1 parallel input pads and any of the
four MIPI CSI-2 virtual channels.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>

--

- Removed some dangling/unused endpoints (ipu2_csi0_from_csi2ipu)
- Renamed the mipi virtual channel endpoint labels, from "mipi_csiX_..."
  to "mipi_vcX...".
- Added input endpoint anchors to the video muxes for the connections
  from parallel sensors.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6dl.dtsi  | 180 +++++++++++++++++++++++++++++++++++++++++
 arch/arm/boot/dts/imx6q.dtsi   | 116 ++++++++++++++++++++++++++
 arch/arm/boot/dts/imx6qdl.dtsi |  10 ++-
 3 files changed, 305 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6dl.dtsi b/arch/arm/boot/dts/imx6dl.dtsi
index 7aa120f..8958c4a 100644
--- a/arch/arm/boot/dts/imx6dl.dtsi
+++ b/arch/arm/boot/dts/imx6dl.dtsi
@@ -181,6 +181,186 @@
 		      "di0", "di1";
 };
 
+&gpr {
+	ipu1_csi0_mux: ipu1_csi0_mux at 34 {
+		compatible = "video-multiplexer";
+		reg = <0x34>;
+		bit-mask = <0x7>;
+		bit-shift = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		port at 0 {
+			reg = <0>;
+
+			ipu1_csi0_mux_from_mipi_vc0: endpoint {
+				remote-endpoint = <&mipi_vc0_to_ipu1_csi0_mux>;
+			};
+		};
+
+		port at 1 {
+			reg = <1>;
+
+			ipu1_csi0_mux_from_mipi_vc1: endpoint {
+				remote-endpoint = <&mipi_vc1_to_ipu1_csi0_mux>;
+			};
+		};
+
+		port at 2 {
+			reg = <2>;
+
+			ipu1_csi0_mux_from_mipi_vc2: endpoint {
+				remote-endpoint = <&mipi_vc2_to_ipu1_csi0_mux>;
+			};
+		};
+
+		port at 3 {
+			reg = <3>;
+
+			ipu1_csi0_mux_from_mipi_vc3: endpoint {
+				remote-endpoint = <&mipi_vc3_to_ipu1_csi0_mux>;
+			};
+		};
+
+		port at 4 {
+			reg = <4>;
+
+			ipu1_csi0_mux_from_parallel_sensor: endpoint {
+			};
+		};
+
+		port at 5 {
+			reg = <5>;
+
+			ipu1_csi0_mux_to_ipu1_csi0: endpoint {
+				remote-endpoint = <&ipu1_csi0_from_ipu1_csi0_mux>;
+			};
+		};
+	};
+
+	ipu1_csi1_mux: ipu1_csi1_mux at 34 {
+		compatible = "video-multiplexer";
+		reg = <0x34>;
+		bit-mask = <0x7>;
+		bit-shift = <3>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		port at 0 {
+			reg = <0>;
+
+			ipu1_csi1_mux_from_mipi_vc0: endpoint {
+				remote-endpoint = <&mipi_vc0_to_ipu1_csi1_mux>;
+			};
+		};
+
+		port at 1 {
+			reg = <1>;
+
+			ipu1_csi1_mux_from_mipi_vc1: endpoint {
+				remote-endpoint = <&mipi_vc1_to_ipu1_csi1_mux>;
+			};
+		};
+
+		port at 2 {
+			reg = <2>;
+
+			ipu1_csi1_mux_from_mipi_vc2: endpoint {
+				remote-endpoint = <&mipi_vc2_to_ipu1_csi1_mux>;
+			};
+		};
+
+		port at 3 {
+			reg = <3>;
+
+			ipu1_csi1_mux_from_mipi_vc3: endpoint {
+				remote-endpoint = <&mipi_vc3_to_ipu1_csi1_mux>;
+			};
+		};
+
+		port at 4 {
+			reg = <4>;
+
+			ipu1_csi1_mux_from_parallel_sensor: endpoint {
+			};
+		};
+
+		port at 5 {
+			reg = <5>;
+
+			ipu1_csi1_mux_to_ipu1_csi1: endpoint {
+				remote-endpoint = <&ipu1_csi1_from_ipu1_csi1_mux>;
+			};
+		};
+	};
+};
+
+&ipu1_csi1 {
+	ipu1_csi1_from_ipu1_csi1_mux: endpoint {
+		remote-endpoint = <&ipu1_csi1_mux_to_ipu1_csi1>;
+	};
+};
+
+&mipi_csi {
+	port at 1 {
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mipi_vc0_to_ipu1_csi0_mux: endpoint at 0 {
+			remote-endpoint = <&ipu1_csi0_mux_from_mipi_vc0>;
+		};
+
+		mipi_vc0_to_ipu1_csi1_mux: endpoint at 1 {
+			remote-endpoint = <&ipu1_csi1_mux_from_mipi_vc0>;
+		};
+	};
+
+	port at 2 {
+		reg = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mipi_vc1_to_ipu1_csi0_mux: endpoint at 0 {
+			remote-endpoint = <&ipu1_csi0_mux_from_mipi_vc1>;
+		};
+
+		mipi_vc1_to_ipu1_csi1_mux: endpoint at 1 {
+			remote-endpoint = <&ipu1_csi1_mux_from_mipi_vc1>;
+		};
+	};
+
+	port at 3 {
+		reg = <3>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mipi_vc2_to_ipu1_csi0_mux: endpoint at 0 {
+			remote-endpoint = <&ipu1_csi0_mux_from_mipi_vc2>;
+		};
+
+		mipi_vc2_to_ipu1_csi1_mux: endpoint at 1 {
+			remote-endpoint = <&ipu1_csi1_mux_from_mipi_vc2>;
+		};
+	};
+
+	port at 4 {
+		reg = <4>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mipi_vc3_to_ipu1_csi0_mux: endpoint at 0 {
+			remote-endpoint = <&ipu1_csi0_mux_from_mipi_vc3>;
+		};
+
+		mipi_vc3_to_ipu1_csi1_mux: endpoint at 1 {
+			remote-endpoint = <&ipu1_csi1_mux_from_mipi_vc3>;
+		};
+	};
+};
+
 &vpu {
 	compatible = "fsl,imx6dl-vpu", "cnm,coda960";
 };
diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi
index e9a5d0b..b833b0d 100644
--- a/arch/arm/boot/dts/imx6q.dtsi
+++ b/arch/arm/boot/dts/imx6q.dtsi
@@ -143,10 +143,18 @@
 
 			ipu2_csi0: port at 0 {
 				reg = <0>;
+
+				ipu2_csi0_from_mipi_vc2: endpoint {
+					remote-endpoint = <&mipi_vc2_to_ipu2_csi0>;
+				};
 			};
 
 			ipu2_csi1: port at 1 {
 				reg = <1>;
+
+				ipu2_csi1_from_ipu2_csi1_mux: endpoint {
+					remote-endpoint = <&ipu2_csi1_mux_to_ipu2_csi1>;
+				};
 			};
 
 			ipu2_di0: port at 2 {
@@ -266,6 +274,80 @@
 	};
 };
 
+&gpr {
+	ipu1_csi0_mux: ipu1_csi0_mux at 4 {
+		compatible = "video-multiplexer";
+		reg = <0x04>;
+		bit-mask = <1>;
+		bit-shift = <19>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		port at 0 {
+			reg = <0>;
+
+			ipu1_csi0_mux_from_mipi_vc0: endpoint {
+				remote-endpoint = <&mipi_vc0_to_ipu1_csi0_mux>;
+			};
+		};
+
+		port at 1 {
+			reg = <1>;
+
+			ipu1_csi0_mux_from_parallel_sensor: endpoint {
+			};
+		};
+
+		port at 2 {
+			reg = <2>;
+
+			ipu1_csi0_mux_to_ipu1_csi0: endpoint {
+				remote-endpoint = <&ipu1_csi0_from_ipu1_csi0_mux>;
+			};
+		};
+	};
+
+	ipu2_csi1_mux: ipu2_csi1_mux at 4 {
+		compatible = "video-multiplexer";
+		reg = <0x04>;
+		bit-mask = <1>;
+		bit-shift = <20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		port at 0 {
+			reg = <0>;
+
+			ipu2_csi1_mux_from_mipi_vc3: endpoint {
+				remote-endpoint = <&mipi_vc3_to_ipu2_csi1_mux>;
+			};
+		};
+
+		port at 1 {
+			reg = <1>;
+
+			ipu2_csi1_mux_from_parallel_sensor: endpoint {
+			};
+		};
+
+		port at 2 {
+			reg = <2>;
+
+			ipu2_csi1_mux_to_ipu2_csi1: endpoint {
+				remote-endpoint = <&ipu2_csi1_from_ipu2_csi1_mux>;
+			};
+		};
+	};
+};
+
+&ipu1_csi1 {
+	ipu1_csi1_from_mipi_vc1: endpoint {
+		remote-endpoint = <&mipi_vc1_to_ipu1_csi1>;
+	};
+};
+
 &ldb {
 	clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>, <&clks IMX6QDL_CLK_LDB_DI1_SEL>,
 		 <&clks IMX6QDL_CLK_IPU1_DI0_SEL>, <&clks IMX6QDL_CLK_IPU1_DI1_SEL>,
@@ -312,6 +394,40 @@
 	};
 };
 
+&mipi_csi {
+	port at 1 {
+		reg = <1>;
+
+		mipi_vc0_to_ipu1_csi0_mux: endpoint {
+			remote-endpoint = <&ipu1_csi0_mux_from_mipi_vc0>;
+		};
+	};
+
+	port at 2 {
+		reg = <2>;
+
+		mipi_vc1_to_ipu1_csi1: endpoint {
+			remote-endpoint = <&ipu1_csi1_from_mipi_vc1>;
+		};
+	};
+
+	port at 3 {
+		reg = <3>;
+
+		mipi_vc2_to_ipu2_csi0: endpoint {
+			remote-endpoint = <&ipu2_csi0_from_mipi_vc2>;
+		};
+	};
+
+	port at 4 {
+		reg = <4>;
+
+		mipi_vc3_to_ipu2_csi1_mux: endpoint {
+			remote-endpoint = <&ipu2_csi1_mux_from_mipi_vc3>;
+		};
+	};
+};
+
 &mipi_dsi {
 	ports {
 		port at 2 {
diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi
index d28a413..194badd 100644
--- a/arch/arm/boot/dts/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/imx6qdl.dtsi
@@ -807,8 +807,10 @@
 			};
 
 			gpr: iomuxc-gpr at 020e0000 {
-				compatible = "fsl,imx6q-iomuxc-gpr", "syscon";
+				compatible = "fsl,imx6q-iomuxc-gpr", "syscon", "simple-mfd";
 				reg = <0x020e0000 0x38>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 			};
 
 			iomuxc: iomuxc at 020e0000 {
@@ -1136,6 +1138,8 @@
 			mipi_csi: mipi at 021dc000 {
 				compatible = "fsl,imx6-mipi-csi2", "snps,dw-mipi-csi2";
 				reg = <0x021dc000 0x4000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				interrupts = <0 100 0x04>, <0 101 0x04>;
 				clocks = <&clks IMX6QDL_CLK_HSI_TX>,
 					 <&clks IMX6QDL_CLK_VIDEO_27M>,
@@ -1243,6 +1247,10 @@
 
 			ipu1_csi0: port at 0 {
 				reg = <0>;
+
+				ipu1_csi0_from_ipu1_csi0_mux: endpoint {
+					remote-endpoint = <&ipu1_csi0_mux_to_ipu1_csi0>;
+				};
 			};
 
 			ipu1_csi1: port at 1 {
-- 
2.7.4

[PATCH v5 06/39] ARM: dts: imx6qdl: add capture-subsystem device

[Steve Longerbeam]

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6dl.dtsi | 5 +++++
 arch/arm/boot/dts/imx6q.dtsi  | 5 +++++
 2 files changed, 10 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl.dtsi b/arch/arm/boot/dts/imx6dl.dtsi
index 8958c4a..a959c76 100644
--- a/arch/arm/boot/dts/imx6dl.dtsi
+++ b/arch/arm/boot/dts/imx6dl.dtsi
@@ -100,6 +100,11 @@
 		};
 	};
 
+	capture-subsystem {
+		compatible = "fsl,imx-capture-subsystem";
+		ports = <&ipu1_csi0>, <&ipu1_csi1>;
+	};
+
 	display-subsystem {
 		compatible = "fsl,imx-display-subsystem";
 		ports = <&ipu1_di0>, <&ipu1_di1>;
diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi
index b833b0d..4cc6579 100644
--- a/arch/arm/boot/dts/imx6q.dtsi
+++ b/arch/arm/boot/dts/imx6q.dtsi
@@ -206,6 +206,11 @@
 		};
 	};
 
+	capture-subsystem {
+		compatible = "fsl,imx-capture-subsystem";
+		ports = <&ipu1_csi0>, <&ipu1_csi1>, <&ipu2_csi0>, <&ipu2_csi1>;
+	};
+
 	display-subsystem {
 		compatible = "fsl,imx-display-subsystem";
 		ports = <&ipu1_di0>, <&ipu1_di1>, <&ipu2_di0>, <&ipu2_di1>;
-- 
2.7.4

[PATCH v5 06/39] ARM: dts: imx6qdl: add capture-subsystem device

[Steve Longerbeam]

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6dl.dtsi | 5 +++++
 arch/arm/boot/dts/imx6q.dtsi  | 5 +++++
 2 files changed, 10 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl.dtsi b/arch/arm/boot/dts/imx6dl.dtsi
index 8958c4a..a959c76 100644
--- a/arch/arm/boot/dts/imx6dl.dtsi
+++ b/arch/arm/boot/dts/imx6dl.dtsi
@@ -100,6 +100,11 @@
 		};
 	};
 
+	capture-subsystem {
+		compatible = "fsl,imx-capture-subsystem";
+		ports = <&ipu1_csi0>, <&ipu1_csi1>;
+	};
+
 	display-subsystem {
 		compatible = "fsl,imx-display-subsystem";
 		ports = <&ipu1_di0>, <&ipu1_di1>;
diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi
index b833b0d..4cc6579 100644
--- a/arch/arm/boot/dts/imx6q.dtsi
+++ b/arch/arm/boot/dts/imx6q.dtsi
@@ -206,6 +206,11 @@
 		};
 	};
 
+	capture-subsystem {
+		compatible = "fsl,imx-capture-subsystem";
+		ports = <&ipu1_csi0>, <&ipu1_csi1>, <&ipu2_csi0>, <&ipu2_csi1>;
+	};
+
 	display-subsystem {
 		compatible = "fsl,imx-display-subsystem";
 		ports = <&ipu1_di0>, <&ipu1_di1>, <&ipu2_di0>, <&ipu2_di1>;
-- 
2.7.4

[PATCH v5 06/39] ARM: dts: imx6qdl: add capture-subsystem device

[Steve Longerbeam]

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6dl.dtsi | 5 +++++
 arch/arm/boot/dts/imx6q.dtsi  | 5 +++++
 2 files changed, 10 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl.dtsi b/arch/arm/boot/dts/imx6dl.dtsi
index 8958c4a..a959c76 100644
--- a/arch/arm/boot/dts/imx6dl.dtsi
+++ b/arch/arm/boot/dts/imx6dl.dtsi
@@ -100,6 +100,11 @@
 		};
 	};
 
+	capture-subsystem {
+		compatible = "fsl,imx-capture-subsystem";
+		ports = <&ipu1_csi0>, <&ipu1_csi1>;
+	};
+
 	display-subsystem {
 		compatible = "fsl,imx-display-subsystem";
 		ports = <&ipu1_di0>, <&ipu1_di1>;
diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi
index b833b0d..4cc6579 100644
--- a/arch/arm/boot/dts/imx6q.dtsi
+++ b/arch/arm/boot/dts/imx6q.dtsi
@@ -206,6 +206,11 @@
 		};
 	};
 
+	capture-subsystem {
+		compatible = "fsl,imx-capture-subsystem";
+		ports = <&ipu1_csi0>, <&ipu1_csi1>, <&ipu2_csi0>, <&ipu2_csi1>;
+	};
+
 	display-subsystem {
 		compatible = "fsl,imx-display-subsystem";
 		ports = <&ipu1_di0>, <&ipu1_di1>, <&ipu2_di0>, <&ipu2_di1>;
-- 
2.7.4

[PATCH v5 07/39] ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround

[Steve Longerbeam]

There is a pin conflict with GPIO_6. This pin functions as a power
input pin to the OV5642 camera sensor, but ENET uses it as the h/w
workaround for erratum ERR006687, to wake-up the ARM cores on normal
RX and TX packet done events. So we need to remove the h/w workaround
to support the OV5642. The result is that the CPUidle driver will no
longer allow entering the deep idle states on the sabrelite.

This is a partial revert of

commit 6261c4c8f13e ("ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC
			interrupt.")
commit a28eeb43ee57 ("ARM: dts: imx6: tag boards that have the HW workaround
			for ERR006687")

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
index 8413179..89dce27 100644
--- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
@@ -270,9 +270,6 @@
 	txd1-skew-ps = <0>;
 	txd2-skew-ps = <0>;
 	txd3-skew-ps = <0>;
-	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
-			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
-	fsl,err006687-workaround-present;
 	status = "okay";
 };
 
@@ -373,7 +370,6 @@
 				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
 				/* Phy reset */
 				MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x000b0
-				MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
 			>;
 		};
 
-- 
2.7.4

[PATCH v5 07/39] ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround

[Steve Longerbeam]

There is a pin conflict with GPIO_6. This pin functions as a power
input pin to the OV5642 camera sensor, but ENET uses it as the h/w
workaround for erratum ERR006687, to wake-up the ARM cores on normal
RX and TX packet done events. So we need to remove the h/w workaround
to support the OV5642. The result is that the CPUidle driver will no
longer allow entering the deep idle states on the sabrelite.

This is a partial revert of

commit 6261c4c8f13e ("ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC
			interrupt.")
commit a28eeb43ee57 ("ARM: dts: imx6: tag boards that have the HW workaround
			for ERR006687")

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
index 8413179..89dce27 100644
--- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
@@ -270,9 +270,6 @@
 	txd1-skew-ps = <0>;
 	txd2-skew-ps = <0>;
 	txd3-skew-ps = <0>;
-	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
-			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
-	fsl,err006687-workaround-present;
 	status = "okay";
 };
 
@@ -373,7 +370,6 @@
 				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
 				/* Phy reset */
 				MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x000b0
-				MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
 			>;
 		};
 
-- 
2.7.4

[PATCH v5 07/39] ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround

[Steve Longerbeam]

There is a pin conflict with GPIO_6. This pin functions as a power
input pin to the OV5642 camera sensor, but ENET uses it as the h/w
workaround for erratum ERR006687, to wake-up the ARM cores on normal
RX and TX packet done events. So we need to remove the h/w workaround
to support the OV5642. The result is that the CPUidle driver will no
longer allow entering the deep idle states on the sabrelite.

This is a partial revert of

commit 6261c4c8f13e ("ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC
			interrupt.")
commit a28eeb43ee57 ("ARM: dts: imx6: tag boards that have the HW workaround
			for ERR006687")

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
index 8413179..89dce27 100644
--- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
@@ -270,9 +270,6 @@
 	txd1-skew-ps = <0>;
 	txd2-skew-ps = <0>;
 	txd3-skew-ps = <0>;
-	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
-			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
-	fsl,err006687-workaround-present;
 	status = "okay";
 };
 
@@ -373,7 +370,6 @@
 				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
 				/* Phy reset */
 				MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x000b0
-				MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
 			>;
 		};
 
-- 
2.7.4

Re: [PATCH v5 07/39] ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround

[Troy Kisky]

On 3/9/2017 8:52 PM, Steve Longerbeam wrote:
> There is a pin conflict with GPIO_6. This pin functions as a power
> input pin to the OV5642 camera sensor, but ENET uses it as the h/w
> workaround for erratum ERR006687, to wake-up the ARM cores on normal
> RX and TX packet done events. So we need to remove the h/w workaround
> to support the OV5642. The result is that the CPUidle driver will no
> longer allow entering the deep idle states on the sabrelite.
> 
> This is a partial revert of
> 
> commit 6261c4c8f13e ("ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC
> 			interrupt.")
> commit a28eeb43ee57 ("ARM: dts: imx6: tag boards that have the HW workaround
> 			for ERR006687")
> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> ---
>  arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 4 ----
>  1 file changed, 4 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> index 8413179..89dce27 100644
> --- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> @@ -270,9 +270,6 @@
>  	txd1-skew-ps = <0>;
>  	txd2-skew-ps = <0>;
>  	txd3-skew-ps = <0>;

How about

+#if !IS_ENABLED(CONFIG_VIDEO_OV5642)

> -	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
> -			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
> -	fsl,err006687-workaround-present;

+#endif

Is that allowed ?


>  	status = "okay";
>  };
>  
> @@ -373,7 +370,6 @@
>  				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
>  				/* Phy reset */
>  				MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x000b0
> -				MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
>  			>;
>  		};
>  
> 

[PATCH v5 07/39] ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround

[Troy Kisky]

On 3/9/2017 8:52 PM, Steve Longerbeam wrote:
> There is a pin conflict with GPIO_6. This pin functions as a power
> input pin to the OV5642 camera sensor, but ENET uses it as the h/w
> workaround for erratum ERR006687, to wake-up the ARM cores on normal
> RX and TX packet done events. So we need to remove the h/w workaround
> to support the OV5642. The result is that the CPUidle driver will no
> longer allow entering the deep idle states on the sabrelite.
> 
> This is a partial revert of
> 
> commit 6261c4c8f13e ("ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC
> 			interrupt.")
> commit a28eeb43ee57 ("ARM: dts: imx6: tag boards that have the HW workaround
> 			for ERR006687")
> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> ---
>  arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 4 ----
>  1 file changed, 4 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> index 8413179..89dce27 100644
> --- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> @@ -270,9 +270,6 @@
>  	txd1-skew-ps = <0>;
>  	txd2-skew-ps = <0>;
>  	txd3-skew-ps = <0>;

How about

+#if !IS_ENABLED(CONFIG_VIDEO_OV5642)

> -	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
> -			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
> -	fsl,err006687-workaround-present;

+#endif

Is that allowed ?


>  	status = "okay";
>  };
>  
> @@ -373,7 +370,6 @@
>  				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
>  				/* Phy reset */
>  				MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x000b0
> -				MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
>  			>;
>  		};
>  
> 

Re: [PATCH v5 07/39] ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround

[Fabio Estevam]

On Fri, Mar 10, 2017 at 3:59 PM, Troy Kisky
<troy.kisky@boundarydevices.com> wrote:
> On 3/9/2017 8:52 PM, Steve Longerbeam wrote:
>> There is a pin conflict with GPIO_6. This pin functions as a power
>> input pin to the OV5642 camera sensor, but ENET uses it as the h/w
>> workaround for erratum ERR006687, to wake-up the ARM cores on normal
>> RX and TX packet done events. So we need to remove the h/w workaround
>> to support the OV5642. The result is that the CPUidle driver will no
>> longer allow entering the deep idle states on the sabrelite.
>>
>> This is a partial revert of
>>
>> commit 6261c4c8f13e ("ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC
>>                       interrupt.")
>> commit a28eeb43ee57 ("ARM: dts: imx6: tag boards that have the HW workaround
>>                       for ERR006687")
>>
>> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
>> ---
>>  arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 4 ----
>>  1 file changed, 4 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>> index 8413179..89dce27 100644
>> --- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>> +++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>> @@ -270,9 +270,6 @@
>>       txd1-skew-ps = <0>;
>>       txd2-skew-ps = <0>;
>>       txd3-skew-ps = <0>;
>
> How about
>
> +#if !IS_ENABLED(CONFIG_VIDEO_OV5642)

Or maybe just create a new device tree for using the camera, like
imx6q-sabrelite-camera.dts.

This way we can keep the FEC erratum for the existing sabrelite dtb's.

[PATCH v5 07/39] ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround

[Fabio Estevam]

On Fri, Mar 10, 2017 at 3:59 PM, Troy Kisky
<troy.kisky@boundarydevices.com> wrote:
> On 3/9/2017 8:52 PM, Steve Longerbeam wrote:
>> There is a pin conflict with GPIO_6. This pin functions as a power
>> input pin to the OV5642 camera sensor, but ENET uses it as the h/w
>> workaround for erratum ERR006687, to wake-up the ARM cores on normal
>> RX and TX packet done events. So we need to remove the h/w workaround
>> to support the OV5642. The result is that the CPUidle driver will no
>> longer allow entering the deep idle states on the sabrelite.
>>
>> This is a partial revert of
>>
>> commit 6261c4c8f13e ("ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC
>>                       interrupt.")
>> commit a28eeb43ee57 ("ARM: dts: imx6: tag boards that have the HW workaround
>>                       for ERR006687")
>>
>> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
>> ---
>>  arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 4 ----
>>  1 file changed, 4 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>> index 8413179..89dce27 100644
>> --- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>> +++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>> @@ -270,9 +270,6 @@
>>       txd1-skew-ps = <0>;
>>       txd2-skew-ps = <0>;
>>       txd3-skew-ps = <0>;
>
> How about
>
> +#if !IS_ENABLED(CONFIG_VIDEO_OV5642)

Or maybe just create a new device tree for using the camera, like
imx6q-sabrelite-camera.dts.

This way we can keep the FEC erratum for the existing sabrelite dtb's.

Re: [PATCH v5 07/39] ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround

[Fabio Estevam]

On Fri, Mar 10, 2017 at 3:59 PM, Troy Kisky
<troy.kisky@boundarydevices.com> wrote:
> On 3/9/2017 8:52 PM, Steve Longerbeam wrote:
>> There is a pin conflict with GPIO_6. This pin functions as a power
>> input pin to the OV5642 camera sensor, but ENET uses it as the h/w
>> workaround for erratum ERR006687, to wake-up the ARM cores on normal
>> RX and TX packet done events. So we need to remove the h/w workaround
>> to support the OV5642. The result is that the CPUidle driver will no
>> longer allow entering the deep idle states on the sabrelite.
>>
>> This is a partial revert of
>>
>> commit 6261c4c8f13e ("ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC
>>                       interrupt.")
>> commit a28eeb43ee57 ("ARM: dts: imx6: tag boards that have the HW workaround
>>                       for ERR006687")
>>
>> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
>> ---
>>  arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 4 ----
>>  1 file changed, 4 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>> index 8413179..89dce27 100644
>> --- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>> +++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>> @@ -270,9 +270,6 @@
>>       txd1-skew-ps = <0>;
>>       txd2-skew-ps = <0>;
>>       txd3-skew-ps = <0>;
>
> How about
>
> +#if !IS_ENABLED(CONFIG_VIDEO_OV5642)

Or maybe just create a new device tree for using the camera, like
imx6q-sabrelite-camera.dts.

This way we can keep the FEC erratum for the existing sabrelite dtb's.

Re: [PATCH v5 07/39] ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround

[Fabio Estevam]

On Fri, Mar 10, 2017 at 3:59 PM, Troy Kisky
<troy.kisky-Q5RJGjKts06CY9SHAMCTRUEOCMrvLtNR@public.gmane.org> wrote:
> On 3/9/2017 8:52 PM, Steve Longerbeam wrote:
>> There is a pin conflict with GPIO_6. This pin functions as a power
>> input pin to the OV5642 camera sensor, but ENET uses it as the h/w
>> workaround for erratum ERR006687, to wake-up the ARM cores on normal
>> RX and TX packet done events. So we need to remove the h/w workaround
>> to support the OV5642. The result is that the CPUidle driver will no
>> longer allow entering the deep idle states on the sabrelite.
>>
>> This is a partial revert of
>>
>> commit 6261c4c8f13e ("ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC
>>                       interrupt.")
>> commit a28eeb43ee57 ("ARM: dts: imx6: tag boards that have the HW workaround
>>                       for ERR006687")
>>
>> Signed-off-by: Steve Longerbeam <steve_longerbeam-nmGgyN9QBj3QT0dZR+AlfA@public.gmane.org>
>> ---
>>  arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 4 ----
>>  1 file changed, 4 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>> index 8413179..89dce27 100644
>> --- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>> +++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>> @@ -270,9 +270,6 @@
>>       txd1-skew-ps = <0>;
>>       txd2-skew-ps = <0>;
>>       txd3-skew-ps = <0>;
>
> How about
>
> +#if !IS_ENABLED(CONFIG_VIDEO_OV5642)

Or maybe just create a new device tree for using the camera, like
imx6q-sabrelite-camera.dts.

This way we can keep the FEC erratum for the existing sabrelite dtb's.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 07/39] ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 1967 bytes --]

On Fri 2017-03-10 16:17:28, Fabio Estevam wrote:
> On Fri, Mar 10, 2017 at 3:59 PM, Troy Kisky
> <troy.kisky@boundarydevices.com> wrote:
> > On 3/9/2017 8:52 PM, Steve Longerbeam wrote:
> >> There is a pin conflict with GPIO_6. This pin functions as a power
> >> input pin to the OV5642 camera sensor, but ENET uses it as the h/w
> >> workaround for erratum ERR006687, to wake-up the ARM cores on normal
> >> RX and TX packet done events. So we need to remove the h/w workaround
> >> to support the OV5642. The result is that the CPUidle driver will no
> >> longer allow entering the deep idle states on the sabrelite.
> >>
> >> This is a partial revert of
> >>
> >> commit 6261c4c8f13e ("ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC
> >>                       interrupt.")
> >> commit a28eeb43ee57 ("ARM: dts: imx6: tag boards that have the HW workaround
> >>                       for ERR006687")
> >>
> >> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> >> ---
> >>  arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 4 ----
> >>  1 file changed, 4 deletions(-)
> >>
> >> diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> >> index 8413179..89dce27 100644
> >> --- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> >> +++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> >> @@ -270,9 +270,6 @@
> >>       txd1-skew-ps = <0>;
> >>       txd2-skew-ps = <0>;
> >>       txd3-skew-ps = <0>;
> >
> > How about
> >
> > +#if !IS_ENABLED(CONFIG_VIDEO_OV5642)

dts is supposed to be hardware description.

> Or maybe just create a new device tree for using the camera, like
> imx6q-sabrelite-camera.dts.

And it should not depend on configuration. Hardware vendor should be
able to ship board with working device tree...

									Pavel

-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

[PATCH v5 07/39] ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround

[Pavel Machek]

On Fri 2017-03-10 16:17:28, Fabio Estevam wrote:
> On Fri, Mar 10, 2017 at 3:59 PM, Troy Kisky
> <troy.kisky@boundarydevices.com> wrote:
> > On 3/9/2017 8:52 PM, Steve Longerbeam wrote:
> >> There is a pin conflict with GPIO_6. This pin functions as a power
> >> input pin to the OV5642 camera sensor, but ENET uses it as the h/w
> >> workaround for erratum ERR006687, to wake-up the ARM cores on normal
> >> RX and TX packet done events. So we need to remove the h/w workaround
> >> to support the OV5642. The result is that the CPUidle driver will no
> >> longer allow entering the deep idle states on the sabrelite.
> >>
> >> This is a partial revert of
> >>
> >> commit 6261c4c8f13e ("ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC
> >>                       interrupt.")
> >> commit a28eeb43ee57 ("ARM: dts: imx6: tag boards that have the HW workaround
> >>                       for ERR006687")
> >>
> >> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> >> ---
> >>  arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 4 ----
> >>  1 file changed, 4 deletions(-)
> >>
> >> diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> >> index 8413179..89dce27 100644
> >> --- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> >> +++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> >> @@ -270,9 +270,6 @@
> >>       txd1-skew-ps = <0>;
> >>       txd2-skew-ps = <0>;
> >>       txd3-skew-ps = <0>;
> >
> > How about
> >
> > +#if !IS_ENABLED(CONFIG_VIDEO_OV5642)

dts is supposed to be hardware description.

> Or maybe just create a new device tree for using the camera, like
> imx6q-sabrelite-camera.dts.

And it should not depend on configuration. Hardware vendor should be
able to ship board with working device tree...

									Pavel

-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 181 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170310/f0ee59e9/attachment.sig>

Re: [PATCH v5 07/39] ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 1967 bytes --]

On Fri 2017-03-10 16:17:28, Fabio Estevam wrote:
> On Fri, Mar 10, 2017 at 3:59 PM, Troy Kisky
> <troy.kisky@boundarydevices.com> wrote:
> > On 3/9/2017 8:52 PM, Steve Longerbeam wrote:
> >> There is a pin conflict with GPIO_6. This pin functions as a power
> >> input pin to the OV5642 camera sensor, but ENET uses it as the h/w
> >> workaround for erratum ERR006687, to wake-up the ARM cores on normal
> >> RX and TX packet done events. So we need to remove the h/w workaround
> >> to support the OV5642. The result is that the CPUidle driver will no
> >> longer allow entering the deep idle states on the sabrelite.
> >>
> >> This is a partial revert of
> >>
> >> commit 6261c4c8f13e ("ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC
> >>                       interrupt.")
> >> commit a28eeb43ee57 ("ARM: dts: imx6: tag boards that have the HW workaround
> >>                       for ERR006687")
> >>
> >> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> >> ---
> >>  arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 4 ----
> >>  1 file changed, 4 deletions(-)
> >>
> >> diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> >> index 8413179..89dce27 100644
> >> --- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> >> +++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> >> @@ -270,9 +270,6 @@
> >>       txd1-skew-ps = <0>;
> >>       txd2-skew-ps = <0>;
> >>       txd3-skew-ps = <0>;
> >
> > How about
> >
> > +#if !IS_ENABLED(CONFIG_VIDEO_OV5642)

dts is supposed to be hardware description.

> Or maybe just create a new device tree for using the camera, like
> imx6q-sabrelite-camera.dts.

And it should not depend on configuration. Hardware vendor should be
able to ship board with working device tree...

									Pavel

-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

Re: [PATCH v5 07/39] ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround

[Pavel Machek]

[-- Attachment #1.1: Type: text/plain, Size: 1967 bytes --]

On Fri 2017-03-10 16:17:28, Fabio Estevam wrote:
> On Fri, Mar 10, 2017 at 3:59 PM, Troy Kisky
> <troy.kisky@boundarydevices.com> wrote:
> > On 3/9/2017 8:52 PM, Steve Longerbeam wrote:
> >> There is a pin conflict with GPIO_6. This pin functions as a power
> >> input pin to the OV5642 camera sensor, but ENET uses it as the h/w
> >> workaround for erratum ERR006687, to wake-up the ARM cores on normal
> >> RX and TX packet done events. So we need to remove the h/w workaround
> >> to support the OV5642. The result is that the CPUidle driver will no
> >> longer allow entering the deep idle states on the sabrelite.
> >>
> >> This is a partial revert of
> >>
> >> commit 6261c4c8f13e ("ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC
> >>                       interrupt.")
> >> commit a28eeb43ee57 ("ARM: dts: imx6: tag boards that have the HW workaround
> >>                       for ERR006687")
> >>
> >> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> >> ---
> >>  arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 4 ----
> >>  1 file changed, 4 deletions(-)
> >>
> >> diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> >> index 8413179..89dce27 100644
> >> --- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> >> +++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> >> @@ -270,9 +270,6 @@
> >>       txd1-skew-ps = <0>;
> >>       txd2-skew-ps = <0>;
> >>       txd3-skew-ps = <0>;
> >
> > How about
> >
> > +#if !IS_ENABLED(CONFIG_VIDEO_OV5642)

dts is supposed to be hardware description.

> Or maybe just create a new device tree for using the camera, like
> imx6q-sabrelite-camera.dts.

And it should not depend on configuration. Hardware vendor should be
able to ship board with working device tree...

									Pavel

-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

[-- Attachment #1.2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

[-- Attachment #2: Type: text/plain, Size: 169 bytes --]

_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

Re: [PATCH v5 07/39] ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround

[Fabio Estevam]

On Fri, Mar 10, 2017 at 6:57 PM, Pavel Machek <pavel@ucw.cz> wrote:

> And it should not depend on configuration. Hardware vendor should be
> able to ship board with working device tree...

We are talking about pin conflict here. Please read the commit log of
this patch for details.

[PATCH v5 07/39] ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround

[Fabio Estevam]

On Fri, Mar 10, 2017 at 6:57 PM, Pavel Machek <pavel@ucw.cz> wrote:

> And it should not depend on configuration. Hardware vendor should be
> able to ship board with working device tree...

We are talking about pin conflict here. Please read the commit log of
this patch for details.

Re: [PATCH v5 07/39] ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround

[Fabio Estevam]

On Fri, Mar 10, 2017 at 6:57 PM, Pavel Machek <pavel@ucw.cz> wrote:

> And it should not depend on configuration. Hardware vendor should be
> able to ship board with working device tree...

We are talking about pin conflict here. Please read the commit log of
this patch for details.

Re: [PATCH v5 07/39] ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround

[Fabio Estevam]

On Fri, Mar 10, 2017 at 6:57 PM, Pavel Machek <pavel-+ZI9xUNit7I@public.gmane.org> wrote:

> And it should not depend on configuration. Hardware vendor should be
> able to ship board with working device tree...

We are talking about pin conflict here. Please read the commit log of
this patch for details.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 07/39] ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround

[Steve Longerbeam]

On 03/10/2017 11:17 AM, Fabio Estevam wrote:
> On Fri, Mar 10, 2017 at 3:59 PM, Troy Kisky
> <troy.kisky@boundarydevices.com> wrote:
>> On 3/9/2017 8:52 PM, Steve Longerbeam wrote:
>>> There is a pin conflict with GPIO_6. This pin functions as a power
>>> input pin to the OV5642 camera sensor, but ENET uses it as the h/w
>>> workaround for erratum ERR006687, to wake-up the ARM cores on normal
>>> RX and TX packet done events. So we need to remove the h/w workaround
>>> to support the OV5642. The result is that the CPUidle driver will no
>>> longer allow entering the deep idle states on the sabrelite.
>>>
>>> This is a partial revert of
>>>
>>> commit 6261c4c8f13e ("ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC
>>>                       interrupt.")
>>> commit a28eeb43ee57 ("ARM: dts: imx6: tag boards that have the HW workaround
>>>                       for ERR006687")
>>>
>>> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
>>> ---
>>>  arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 4 ----
>>>  1 file changed, 4 deletions(-)
>>>
>>> diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>>> index 8413179..89dce27 100644
>>> --- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>>> +++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>>> @@ -270,9 +270,6 @@
>>>       txd1-skew-ps = <0>;
>>>       txd2-skew-ps = <0>;
>>>       txd3-skew-ps = <0>;
>>
>> How about
>>
>> +#if !IS_ENABLED(CONFIG_VIDEO_OV5642)
>
> Or maybe just create a new device tree for using the camera, like
> imx6q-sabrelite-camera.dts.
>
> This way we can keep the FEC erratum for the existing sabrelite dtb's.

Is it really necessary to keep the erratum in sabrelite dts? Because the
sabrelite is a _reference_ platform, vendors use this dts as a working
example of how to configure their imx6-based hardware. So as a working
example, it should contain as much example hardware config as possible
as a guide. If a vendor does not require OV5642 support and requires
the lower power consumption that the erratum workaround provides, they
can refer to other example imx6 dts files which still implement the
erratum, or look at the git log of this file.

Steve

[PATCH v5 07/39] ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround

[Steve Longerbeam]

On 03/10/2017 11:17 AM, Fabio Estevam wrote:
> On Fri, Mar 10, 2017 at 3:59 PM, Troy Kisky
> <troy.kisky@boundarydevices.com> wrote:
>> On 3/9/2017 8:52 PM, Steve Longerbeam wrote:
>>> There is a pin conflict with GPIO_6. This pin functions as a power
>>> input pin to the OV5642 camera sensor, but ENET uses it as the h/w
>>> workaround for erratum ERR006687, to wake-up the ARM cores on normal
>>> RX and TX packet done events. So we need to remove the h/w workaround
>>> to support the OV5642. The result is that the CPUidle driver will no
>>> longer allow entering the deep idle states on the sabrelite.
>>>
>>> This is a partial revert of
>>>
>>> commit 6261c4c8f13e ("ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC
>>>                       interrupt.")
>>> commit a28eeb43ee57 ("ARM: dts: imx6: tag boards that have the HW workaround
>>>                       for ERR006687")
>>>
>>> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
>>> ---
>>>  arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 4 ----
>>>  1 file changed, 4 deletions(-)
>>>
>>> diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>>> index 8413179..89dce27 100644
>>> --- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>>> +++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>>> @@ -270,9 +270,6 @@
>>>       txd1-skew-ps = <0>;
>>>       txd2-skew-ps = <0>;
>>>       txd3-skew-ps = <0>;
>>
>> How about
>>
>> +#if !IS_ENABLED(CONFIG_VIDEO_OV5642)
>
> Or maybe just create a new device tree for using the camera, like
> imx6q-sabrelite-camera.dts.
>
> This way we can keep the FEC erratum for the existing sabrelite dtb's.

Is it really necessary to keep the erratum in sabrelite dts? Because the
sabrelite is a _reference_ platform, vendors use this dts as a working
example of how to configure their imx6-based hardware. So as a working
example, it should contain as much example hardware config as possible
as a guide. If a vendor does not require OV5642 support and requires
the lower power consumption that the erratum workaround provides, they
can refer to other example imx6 dts files which still implement the
erratum, or look at the git log of this file.

Steve

Re: [PATCH v5 07/39] ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround

[Steve Longerbeam]

On 03/10/2017 11:17 AM, Fabio Estevam wrote:
> On Fri, Mar 10, 2017 at 3:59 PM, Troy Kisky
> <troy.kisky@boundarydevices.com> wrote:
>> On 3/9/2017 8:52 PM, Steve Longerbeam wrote:
>>> There is a pin conflict with GPIO_6. This pin functions as a power
>>> input pin to the OV5642 camera sensor, but ENET uses it as the h/w
>>> workaround for erratum ERR006687, to wake-up the ARM cores on normal
>>> RX and TX packet done events. So we need to remove the h/w workaround
>>> to support the OV5642. The result is that the CPUidle driver will no
>>> longer allow entering the deep idle states on the sabrelite.
>>>
>>> This is a partial revert of
>>>
>>> commit 6261c4c8f13e ("ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC
>>>                       interrupt.")
>>> commit a28eeb43ee57 ("ARM: dts: imx6: tag boards that have the HW workaround
>>>                       for ERR006687")
>>>
>>> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
>>> ---
>>>  arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 4 ----
>>>  1 file changed, 4 deletions(-)
>>>
>>> diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>>> index 8413179..89dce27 100644
>>> --- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>>> +++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>>> @@ -270,9 +270,6 @@
>>>       txd1-skew-ps = <0>;
>>>       txd2-skew-ps = <0>;
>>>       txd3-skew-ps = <0>;
>>
>> How about
>>
>> +#if !IS_ENABLED(CONFIG_VIDEO_OV5642)
>
> Or maybe just create a new device tree for using the camera, like
> imx6q-sabrelite-camera.dts.
>
> This way we can keep the FEC erratum for the existing sabrelite dtb's.

Is it really necessary to keep the erratum in sabrelite dts? Because the
sabrelite is a _reference_ platform, vendors use this dts as a working
example of how to configure their imx6-based hardware. So as a working
example, it should contain as much example hardware config as possible
as a guide. If a vendor does not require OV5642 support and requires
the lower power consumption that the erratum workaround provides, they
can refer to other example imx6 dts files which still implement the
erratum, or look at the git log of this file.

Steve

Re: [PATCH v5 07/39] ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround

[Steve Longerbeam]

On 03/10/2017 11:17 AM, Fabio Estevam wrote:
> On Fri, Mar 10, 2017 at 3:59 PM, Troy Kisky
> <troy.kisky@boundarydevices.com> wrote:
>> On 3/9/2017 8:52 PM, Steve Longerbeam wrote:
>>> There is a pin conflict with GPIO_6. This pin functions as a power
>>> input pin to the OV5642 camera sensor, but ENET uses it as the h/w
>>> workaround for erratum ERR006687, to wake-up the ARM cores on normal
>>> RX and TX packet done events. So we need to remove the h/w workaround
>>> to support the OV5642. The result is that the CPUidle driver will no
>>> longer allow entering the deep idle states on the sabrelite.
>>>
>>> This is a partial revert of
>>>
>>> commit 6261c4c8f13e ("ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC
>>>                       interrupt.")
>>> commit a28eeb43ee57 ("ARM: dts: imx6: tag boards that have the HW workaround
>>>                       for ERR006687")
>>>
>>> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
>>> ---
>>>  arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 4 ----
>>>  1 file changed, 4 deletions(-)
>>>
>>> diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>>> index 8413179..89dce27 100644
>>> --- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>>> +++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
>>> @@ -270,9 +270,6 @@
>>>       txd1-skew-ps = <0>;
>>>       txd2-skew-ps = <0>;
>>>       txd3-skew-ps = <0>;
>>
>> How about
>>
>> +#if !IS_ENABLED(CONFIG_VIDEO_OV5642)
>
> Or maybe just create a new device tree for using the camera, like
> imx6q-sabrelite-camera.dts.
>
> This way we can keep the FEC erratum for the existing sabrelite dtb's.

Is it really necessary to keep the erratum in sabrelite dts? Because the
sabrelite is a _reference_ platform, vendors use this dts as a working
example of how to configure their imx6-based hardware. So as a working
example, it should contain as much example hardware config as possible
as a guide. If a vendor does not require OV5642 support and requires
the lower power consumption that the erratum workaround provides, they
can refer to other example imx6 dts files which still implement the
erratum, or look at the git log of this file.

Steve

[PATCH v5 08/39] ARM: dts: imx6-sabrelite: add OV5642 and OV5640 camera sensors

[Steve Longerbeam]

Adds the OV5642 parallel-bus sensor, and the OV5640 MIPI CSI-2 sensor.
Both hang off the same i2c2 bus, so they require different (and non-
default) i2c slave addresses.

The OV5642 connects to the parallel-bus mux input port on ipu1_csi0_mux.

The OV5640 connects to the input port on the MIPI CSI-2 receiver on
mipi_csi.

The OV5642 node is disabled temporarily while the subdev driver is
cleaned up and submitted later.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6dl-sabrelite.dts   |   5 ++
 arch/arm/boot/dts/imx6q-sabrelite.dts    |   5 ++
 arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 148 +++++++++++++++++++++++++++++++
 3 files changed, 158 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-sabrelite.dts b/arch/arm/boot/dts/imx6dl-sabrelite.dts
index 2f90452..3304076 100644
--- a/arch/arm/boot/dts/imx6dl-sabrelite.dts
+++ b/arch/arm/boot/dts/imx6dl-sabrelite.dts
@@ -48,3 +48,8 @@
 	model = "Freescale i.MX6 DualLite SABRE Lite Board";
 	compatible = "fsl,imx6dl-sabrelite", "fsl,imx6dl";
 };
+
+&ipu1_csi1_from_ipu1_csi1_mux {
+	clock-lanes = <0>;
+	data-lanes = <1 2>;
+};
diff --git a/arch/arm/boot/dts/imx6q-sabrelite.dts b/arch/arm/boot/dts/imx6q-sabrelite.dts
index 02a7cdf..dc51262e 100644
--- a/arch/arm/boot/dts/imx6q-sabrelite.dts
+++ b/arch/arm/boot/dts/imx6q-sabrelite.dts
@@ -52,3 +52,8 @@
 &sata {
 	status = "okay";
 };
+
+&ipu1_csi1_from_mipi_vc1 {
+	clock-lanes = <0>;
+	data-lanes = <1 2>;
+};
diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
index 89dce27..afe7449 100644
--- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
@@ -39,6 +39,8 @@
  *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
+
+#include <dt-bindings/clock/imx6qdl-clock.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 
@@ -94,6 +96,42 @@
 			pinctrl-0 = <&pinctrl_can_xcvr>;
 			gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
 		};
+
+		reg_1p5v: regulator@4 {
+			compatible = "regulator-fixed";
+			reg = <4>;
+			regulator-name = "1P5V";
+			regulator-min-microvolt = <1500000>;
+			regulator-max-microvolt = <1500000>;
+			regulator-always-on;
+		};
+
+		reg_1p8v: regulator@5 {
+			compatible = "regulator-fixed";
+			reg = <5>;
+			regulator-name = "1P8V";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		reg_2p8v: regulator@6 {
+			compatible = "regulator-fixed";
+			reg = <6>;
+			regulator-name = "2P8V";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-always-on;
+		};
+	};
+
+	mipi_xclk: mipi_xclk {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <22000000>;
+		clock-output-names = "mipi_pwm3";
+		pwms = <&pwm3 0 45>; /* 1 / 45 ns = 22 MHz */
+		status = "okay";
 	};
 
 	gpio-keys {
@@ -220,6 +258,22 @@
 	};
 };
 
+&ipu1_csi0_from_ipu1_csi0_mux {
+	bus-width = <8>;
+	data-shift = <12>; /* Lines 19:12 used */
+	hsync-active = <1>;
+	vync-active = <1>;
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+	remote-endpoint = <&ov5642_to_ipu1_csi0_mux>;
+};
+
+&ipu1_csi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ipu1_csi0>;
+};
+
 &audmux {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_audmux>;
@@ -298,6 +352,53 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
+
+	ov5640: camera@40 {
+		compatible = "ovti,ov5640";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5640>;
+		reg = <0x40>;
+		clocks = <&mipi_xclk>;
+		clock-names = "xclk";
+		DOVDD-supply = <&reg_1p8v>;
+		AVDD-supply = <&reg_2p8v>;
+		DVDD-supply = <&reg_1p5v>;
+		reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; /* NANDF_D5 */
+		powerdown-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* NANDF_WP_B */
+
+		port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ov5640_to_mipi_csi2: endpoint {
+				remote-endpoint = <&mipi_csi2_in>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+
+	ov5642: camera@42 {
+		compatible = "ovti,ov5642";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5642>;
+		clocks = <&clks IMX6QDL_CLK_CKO2>;
+		clock-names = "xclk";
+		reg = <0x42>;
+		reset-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+		powerdown-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+		gp-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+
+		port {
+			ov5642_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+				bus-width = <8>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+			};
+		};
+	};
 };
 
 &i2c3 {
@@ -411,6 +512,23 @@
 			>;
 		};
 
+		pinctrl_ipu1_csi0: ipu1csi0grp {
+			fsl,pins = <
+				MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19    0x1b0b0
+				MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK   0x1b0b0
+				MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC      0x1b0b0
+				MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC     0x1b0b0
+				MX6QDL_PAD_CSI0_DATA_EN__IPU1_CSI0_DATA_EN 0x1b0b0
+			>;
+		};
+
 		pinctrl_j15: j15grp {
 			fsl,pins = <
 				MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
@@ -444,6 +562,22 @@
 			>;
 		};
 
+		pinctrl_ov5640: ov5640grp {
+			fsl,pins = <
+				MX6QDL_PAD_NANDF_D5__GPIO2_IO05   0x000b0
+				MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09 0x0b0b0
+			>;
+		};
+
+		pinctrl_ov5642: ov5642grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x1b0b0
+				MX6QDL_PAD_GPIO_6__GPIO1_IO06   0x1b0b0
+				MX6QDL_PAD_GPIO_8__GPIO1_IO08   0x130b0
+				MX6QDL_PAD_GPIO_3__CCM_CLKO2    0x000b0
+			>;
+		};
+
 		pinctrl_pwm1: pwm1grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1
@@ -598,3 +732,17 @@
 	vmmc-supply = <&reg_3p3v>;
 	status = "okay";
 };
+
+&mipi_csi {
+	status = "okay";
+
+	port@0 {
+		reg = <0>;
+
+		mipi_csi2_in: endpoint {
+			remote-endpoint = <&ov5640_to_mipi_csi2>;
+			clock-lanes = <0>;
+			data-lanes = <1 2>;
+		};
+	};
+};
-- 
2.7.4

[PATCH v5 08/39] ARM: dts: imx6-sabrelite: add OV5642 and OV5640 camera sensors

[Steve Longerbeam]

Adds the OV5642 parallel-bus sensor, and the OV5640 MIPI CSI-2 sensor.
Both hang off the same i2c2 bus, so they require different (and non-
default) i2c slave addresses.

The OV5642 connects to the parallel-bus mux input port on ipu1_csi0_mux.

The OV5640 connects to the input port on the MIPI CSI-2 receiver on
mipi_csi.

The OV5642 node is disabled temporarily while the subdev driver is
cleaned up and submitted later.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6dl-sabrelite.dts   |   5 ++
 arch/arm/boot/dts/imx6q-sabrelite.dts    |   5 ++
 arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 148 +++++++++++++++++++++++++++++++
 3 files changed, 158 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-sabrelite.dts b/arch/arm/boot/dts/imx6dl-sabrelite.dts
index 2f90452..3304076 100644
--- a/arch/arm/boot/dts/imx6dl-sabrelite.dts
+++ b/arch/arm/boot/dts/imx6dl-sabrelite.dts
@@ -48,3 +48,8 @@
 	model = "Freescale i.MX6 DualLite SABRE Lite Board";
 	compatible = "fsl,imx6dl-sabrelite", "fsl,imx6dl";
 };
+
+&ipu1_csi1_from_ipu1_csi1_mux {
+	clock-lanes = <0>;
+	data-lanes = <1 2>;
+};
diff --git a/arch/arm/boot/dts/imx6q-sabrelite.dts b/arch/arm/boot/dts/imx6q-sabrelite.dts
index 02a7cdf..dc51262e 100644
--- a/arch/arm/boot/dts/imx6q-sabrelite.dts
+++ b/arch/arm/boot/dts/imx6q-sabrelite.dts
@@ -52,3 +52,8 @@
 &sata {
 	status = "okay";
 };
+
+&ipu1_csi1_from_mipi_vc1 {
+	clock-lanes = <0>;
+	data-lanes = <1 2>;
+};
diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
index 89dce27..afe7449 100644
--- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
@@ -39,6 +39,8 @@
  *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
+
+#include <dt-bindings/clock/imx6qdl-clock.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 
@@ -94,6 +96,42 @@
 			pinctrl-0 = <&pinctrl_can_xcvr>;
 			gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
 		};
+
+		reg_1p5v: regulator at 4 {
+			compatible = "regulator-fixed";
+			reg = <4>;
+			regulator-name = "1P5V";
+			regulator-min-microvolt = <1500000>;
+			regulator-max-microvolt = <1500000>;
+			regulator-always-on;
+		};
+
+		reg_1p8v: regulator at 5 {
+			compatible = "regulator-fixed";
+			reg = <5>;
+			regulator-name = "1P8V";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		reg_2p8v: regulator at 6 {
+			compatible = "regulator-fixed";
+			reg = <6>;
+			regulator-name = "2P8V";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-always-on;
+		};
+	};
+
+	mipi_xclk: mipi_xclk {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <22000000>;
+		clock-output-names = "mipi_pwm3";
+		pwms = <&pwm3 0 45>; /* 1 / 45 ns = 22 MHz */
+		status = "okay";
 	};
 
 	gpio-keys {
@@ -220,6 +258,22 @@
 	};
 };
 
+&ipu1_csi0_from_ipu1_csi0_mux {
+	bus-width = <8>;
+	data-shift = <12>; /* Lines 19:12 used */
+	hsync-active = <1>;
+	vync-active = <1>;
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+	remote-endpoint = <&ov5642_to_ipu1_csi0_mux>;
+};
+
+&ipu1_csi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ipu1_csi0>;
+};
+
 &audmux {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_audmux>;
@@ -298,6 +352,53 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
+
+	ov5640: camera at 40 {
+		compatible = "ovti,ov5640";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5640>;
+		reg = <0x40>;
+		clocks = <&mipi_xclk>;
+		clock-names = "xclk";
+		DOVDD-supply = <&reg_1p8v>;
+		AVDD-supply = <&reg_2p8v>;
+		DVDD-supply = <&reg_1p5v>;
+		reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; /* NANDF_D5 */
+		powerdown-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* NANDF_WP_B */
+
+		port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ov5640_to_mipi_csi2: endpoint {
+				remote-endpoint = <&mipi_csi2_in>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+
+	ov5642: camera at 42 {
+		compatible = "ovti,ov5642";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5642>;
+		clocks = <&clks IMX6QDL_CLK_CKO2>;
+		clock-names = "xclk";
+		reg = <0x42>;
+		reset-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+		powerdown-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+		gp-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+
+		port {
+			ov5642_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+				bus-width = <8>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+			};
+		};
+	};
 };
 
 &i2c3 {
@@ -411,6 +512,23 @@
 			>;
 		};
 
+		pinctrl_ipu1_csi0: ipu1csi0grp {
+			fsl,pins = <
+				MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19    0x1b0b0
+				MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK   0x1b0b0
+				MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC      0x1b0b0
+				MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC     0x1b0b0
+				MX6QDL_PAD_CSI0_DATA_EN__IPU1_CSI0_DATA_EN 0x1b0b0
+			>;
+		};
+
 		pinctrl_j15: j15grp {
 			fsl,pins = <
 				MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
@@ -444,6 +562,22 @@
 			>;
 		};
 
+		pinctrl_ov5640: ov5640grp {
+			fsl,pins = <
+				MX6QDL_PAD_NANDF_D5__GPIO2_IO05   0x000b0
+				MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09 0x0b0b0
+			>;
+		};
+
+		pinctrl_ov5642: ov5642grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x1b0b0
+				MX6QDL_PAD_GPIO_6__GPIO1_IO06   0x1b0b0
+				MX6QDL_PAD_GPIO_8__GPIO1_IO08   0x130b0
+				MX6QDL_PAD_GPIO_3__CCM_CLKO2    0x000b0
+			>;
+		};
+
 		pinctrl_pwm1: pwm1grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1
@@ -598,3 +732,17 @@
 	vmmc-supply = <&reg_3p3v>;
 	status = "okay";
 };
+
+&mipi_csi {
+	status = "okay";
+
+	port at 0 {
+		reg = <0>;
+
+		mipi_csi2_in: endpoint {
+			remote-endpoint = <&ov5640_to_mipi_csi2>;
+			clock-lanes = <0>;
+			data-lanes = <1 2>;
+		};
+	};
+};
-- 
2.7.4

[PATCH v5 09/39] ARM: dts: imx6-sabresd: add OV5642 and OV5640 camera sensors

[Steve Longerbeam]

Enables the OV5642 parallel-bus sensor, and the OV5640 MIPI CSI-2 sensor.

The OV5642 connects to the parallel-bus mux input port on ipu1_csi0_mux.

The OV5640 connects to the input port on the MIPI CSI-2 receiver on
mipi_csi.

Until the OV5652 sensor module compatible with the SabreSD becomes
available for testing, the ov5642 node is currently disabled.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6dl-sabresd.dts   |   5 ++
 arch/arm/boot/dts/imx6q-sabresd.dts    |   5 ++
 arch/arm/boot/dts/imx6qdl-sabresd.dtsi | 114 ++++++++++++++++++++++++++++++++-
 3 files changed, 123 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6dl-sabresd.dts b/arch/arm/boot/dts/imx6dl-sabresd.dts
index 1e45f2f..9607afe 100644
--- a/arch/arm/boot/dts/imx6dl-sabresd.dts
+++ b/arch/arm/boot/dts/imx6dl-sabresd.dts
@@ -15,3 +15,8 @@
 	model = "Freescale i.MX6 DualLite SABRE Smart Device Board";
 	compatible = "fsl,imx6dl-sabresd", "fsl,imx6dl";
 };
+
+&ipu1_csi1_from_ipu1_csi1_mux {
+	clock-lanes = <0>;
+	data-lanes = <1 2>;
+};
diff --git a/arch/arm/boot/dts/imx6q-sabresd.dts b/arch/arm/boot/dts/imx6q-sabresd.dts
index 9cbdfe7..527772b 100644
--- a/arch/arm/boot/dts/imx6q-sabresd.dts
+++ b/arch/arm/boot/dts/imx6q-sabresd.dts
@@ -23,3 +23,8 @@
 &sata {
 	status = "okay";
 };
+
+&ipu1_csi1_from_mipi_vc1 {
+	clock-lanes = <0>;
+	data-lanes = <1 2>;
+};
diff --git a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
index 63bf95e..643c1d4 100644
--- a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
@@ -10,6 +10,7 @@
  * http://www.gnu.org/copyleft/gpl.html
  */
 
+#include <dt-bindings/clock/imx6qdl-clock.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 
@@ -146,6 +147,36 @@
 	};
 };
 
+&ipu1_csi0_from_ipu1_csi0_mux {
+	bus-width = <8>;
+	data-shift = <12>; /* Lines 19:12 used */
+	hsync-active = <1>;
+	vsync-active = <1>;
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+	remote-endpoint = <&ov5642_to_ipu1_csi0_mux>;
+};
+
+&ipu1_csi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ipu1_csi0>;
+};
+
+&mipi_csi {
+	status = "okay";
+
+	port@0 {
+		reg = <0>;
+
+		mipi_csi2_in: endpoint {
+			remote-endpoint = <&ov5640_to_mipi_csi2>;
+			clock-lanes = <0>;
+			data-lanes = <1 2>;
+		};
+	};
+};
+
 &audmux {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_audmux>;
@@ -213,7 +244,32 @@
 			0x8014 /* 4:FN_DMICCDAT */
 			0x0000 /* 5:Default */
 		>;
-       };
+	};
+
+	ov5642: camera@3c {
+		compatible = "ovti,ov5642";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5642>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		clock-names = "xclk";
+		reg = <0x3c>;
+		DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+		AVDD-supply = <&vgen3_reg>;  /* 2.8v, rev C board is VGEN3
+						rev B board is VGEN5 */
+		DVDD-supply = <&vgen2_reg>;  /* 1.5v*/
+		powerdown-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+		status = "disabled";
+
+		port {
+			ov5642_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+				bus-width = <8>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+			};
+		};
+	};
 };
 
 &i2c2 {
@@ -222,6 +278,32 @@
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
+	ov5640: camera@3c {
+		compatible = "ovti,ov5640";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5640>;
+		reg = <0x3c>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		clock-names = "xclk";
+		DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+		AVDD-supply = <&vgen3_reg>;  /* 2.8v, rev C board is VGEN3
+						rev B board is VGEN5 */
+		DVDD-supply = <&vgen2_reg>;  /* 1.5v*/
+		powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+
+		port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ov5640_to_mipi_csi2: endpoint {
+				remote-endpoint = <&mipi_csi2_in>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+
 	pmic: pfuze100@08 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
@@ -425,6 +507,36 @@
 			>;
 		};
 
+		pinctrl_ipu1_csi0: ipu1csi0grp {
+			fsl,pins = <
+				MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19    0x1b0b0
+				MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK   0x1b0b0
+				MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC      0x1b0b0
+				MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC     0x1b0b0
+			>;
+		};
+
+		pinctrl_ov5640: ov5640grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT2__GPIO1_IO19 0x1b0b0
+				MX6QDL_PAD_SD1_CLK__GPIO1_IO20  0x1b0b0
+			>;
+		};
+
+		pinctrl_ov5642: ov5642grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x1b0b0
+				MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b0
+			>;
+		};
+
 		pinctrl_pcie: pciegrp {
 			fsl,pins = <
 				MX6QDL_PAD_GPIO_17__GPIO7_IO12	0x1b0b0
-- 
2.7.4

[PATCH v5 09/39] ARM: dts: imx6-sabresd: add OV5642 and OV5640 camera sensors

[Steve Longerbeam]

Enables the OV5642 parallel-bus sensor, and the OV5640 MIPI CSI-2 sensor.

The OV5642 connects to the parallel-bus mux input port on ipu1_csi0_mux.

The OV5640 connects to the input port on the MIPI CSI-2 receiver on
mipi_csi.

Until the OV5652 sensor module compatible with the SabreSD becomes
available for testing, the ov5642 node is currently disabled.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6dl-sabresd.dts   |   5 ++
 arch/arm/boot/dts/imx6q-sabresd.dts    |   5 ++
 arch/arm/boot/dts/imx6qdl-sabresd.dtsi | 114 ++++++++++++++++++++++++++++++++-
 3 files changed, 123 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6dl-sabresd.dts b/arch/arm/boot/dts/imx6dl-sabresd.dts
index 1e45f2f..9607afe 100644
--- a/arch/arm/boot/dts/imx6dl-sabresd.dts
+++ b/arch/arm/boot/dts/imx6dl-sabresd.dts
@@ -15,3 +15,8 @@
 	model = "Freescale i.MX6 DualLite SABRE Smart Device Board";
 	compatible = "fsl,imx6dl-sabresd", "fsl,imx6dl";
 };
+
+&ipu1_csi1_from_ipu1_csi1_mux {
+	clock-lanes = <0>;
+	data-lanes = <1 2>;
+};
diff --git a/arch/arm/boot/dts/imx6q-sabresd.dts b/arch/arm/boot/dts/imx6q-sabresd.dts
index 9cbdfe7..527772b 100644
--- a/arch/arm/boot/dts/imx6q-sabresd.dts
+++ b/arch/arm/boot/dts/imx6q-sabresd.dts
@@ -23,3 +23,8 @@
 &sata {
 	status = "okay";
 };
+
+&ipu1_csi1_from_mipi_vc1 {
+	clock-lanes = <0>;
+	data-lanes = <1 2>;
+};
diff --git a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
index 63bf95e..643c1d4 100644
--- a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
@@ -10,6 +10,7 @@
  * http://www.gnu.org/copyleft/gpl.html
  */
 
+#include <dt-bindings/clock/imx6qdl-clock.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 
@@ -146,6 +147,36 @@
 	};
 };
 
+&ipu1_csi0_from_ipu1_csi0_mux {
+	bus-width = <8>;
+	data-shift = <12>; /* Lines 19:12 used */
+	hsync-active = <1>;
+	vsync-active = <1>;
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+	remote-endpoint = <&ov5642_to_ipu1_csi0_mux>;
+};
+
+&ipu1_csi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ipu1_csi0>;
+};
+
+&mipi_csi {
+	status = "okay";
+
+	port at 0 {
+		reg = <0>;
+
+		mipi_csi2_in: endpoint {
+			remote-endpoint = <&ov5640_to_mipi_csi2>;
+			clock-lanes = <0>;
+			data-lanes = <1 2>;
+		};
+	};
+};
+
 &audmux {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_audmux>;
@@ -213,7 +244,32 @@
 			0x8014 /* 4:FN_DMICCDAT */
 			0x0000 /* 5:Default */
 		>;
-       };
+	};
+
+	ov5642: camera at 3c {
+		compatible = "ovti,ov5642";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5642>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		clock-names = "xclk";
+		reg = <0x3c>;
+		DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+		AVDD-supply = <&vgen3_reg>;  /* 2.8v, rev C board is VGEN3
+						rev B board is VGEN5 */
+		DVDD-supply = <&vgen2_reg>;  /* 1.5v*/
+		powerdown-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+		status = "disabled";
+
+		port {
+			ov5642_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+				bus-width = <8>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+			};
+		};
+	};
 };
 
 &i2c2 {
@@ -222,6 +278,32 @@
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
+	ov5640: camera at 3c {
+		compatible = "ovti,ov5640";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5640>;
+		reg = <0x3c>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		clock-names = "xclk";
+		DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+		AVDD-supply = <&vgen3_reg>;  /* 2.8v, rev C board is VGEN3
+						rev B board is VGEN5 */
+		DVDD-supply = <&vgen2_reg>;  /* 1.5v*/
+		powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+
+		port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ov5640_to_mipi_csi2: endpoint {
+				remote-endpoint = <&mipi_csi2_in>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+
 	pmic: pfuze100 at 08 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
@@ -425,6 +507,36 @@
 			>;
 		};
 
+		pinctrl_ipu1_csi0: ipu1csi0grp {
+			fsl,pins = <
+				MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18    0x1b0b0
+				MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19    0x1b0b0
+				MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK   0x1b0b0
+				MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC      0x1b0b0
+				MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC     0x1b0b0
+			>;
+		};
+
+		pinctrl_ov5640: ov5640grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT2__GPIO1_IO19 0x1b0b0
+				MX6QDL_PAD_SD1_CLK__GPIO1_IO20  0x1b0b0
+			>;
+		};
+
+		pinctrl_ov5642: ov5642grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x1b0b0
+				MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b0
+			>;
+		};
+
 		pinctrl_pcie: pciegrp {
 			fsl,pins = <
 				MX6QDL_PAD_GPIO_17__GPIO7_IO12	0x1b0b0
-- 
2.7.4

[PATCH v5 10/39] ARM: dts: imx6-sabreauto: create i2cmux for i2c3

[Steve Longerbeam]

The sabreauto uses a steering pin to select between the SDA signal on
i2c3 bus, and a data-in pin for an SPI NOR chip. Use i2cmux to control
this steering pin. Idle state of the i2cmux selects SPI NOR. This is not
a classic way to use i2cmux, since one side of the mux selects something
other than an i2c bus, but it works and is probably the cleanest
solution. Note that if one thread is attempting to access SPI NOR while
another thread is accessing i2c3, the SPI NOR access will fail since the
i2cmux has selected the SDA pin rather than SPI NOR data-in. This couldn't
be avoided in any case, the board is not designed to allow concurrent
i2c3 and SPI NOR functions (and the default device-tree does not enable
SPI NOR anyway).

Devices hanging off i2c3 should now be defined under i2cmux, so
that the steering pin can be properly controlled to access those
devices. The port expanders (MAX7310) are thus moved into i2cmux.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 65 +++++++++++++++++++++-----------
 1 file changed, 44 insertions(+), 21 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
index a2a714d..c8e35c4 100644
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
@@ -108,6 +108,44 @@
 		default-brightness-level = <7>;
 		status = "okay";
 	};
+
+	i2cmux {
+		compatible = "i2c-mux-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2c3mux>;
+		mux-gpios = <&gpio5 4 0>;
+		i2c-parent = <&i2c3>;
+		idle-state = <0>;
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			max7310_a: gpio@30 {
+				compatible = "maxim,max7310";
+				reg = <0x30>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			max7310_b: gpio@32 {
+				compatible = "maxim,max7310";
+				reg = <0x32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			max7310_c: gpio@34 {
+				compatible = "maxim,max7310";
+				reg = <0x34>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+		};
+	};
 };
 
 &clks {
@@ -290,27 +328,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c3>;
 	status = "okay";
-
-	max7310_a: gpio@30 {
-		compatible = "maxim,max7310";
-		reg = <0x30>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	max7310_b: gpio@32 {
-		compatible = "maxim,max7310";
-		reg = <0x32>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	max7310_c: gpio@34 {
-		compatible = "maxim,max7310";
-		reg = <0x34>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
 };
 
 &iomuxc {
@@ -418,6 +435,12 @@
 			>;
 		};
 
+		pinctrl_i2c3mux: i2c3muxgrp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x0b0b1
+			>;
+		};
+
 		pinctrl_pwm3: pwm1grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
-- 
2.7.4

[PATCH v5 10/39] ARM: dts: imx6-sabreauto: create i2cmux for i2c3

[Steve Longerbeam]

The sabreauto uses a steering pin to select between the SDA signal on
i2c3 bus, and a data-in pin for an SPI NOR chip. Use i2cmux to control
this steering pin. Idle state of the i2cmux selects SPI NOR. This is not
a classic way to use i2cmux, since one side of the mux selects something
other than an i2c bus, but it works and is probably the cleanest
solution. Note that if one thread is attempting to access SPI NOR while
another thread is accessing i2c3, the SPI NOR access will fail since the
i2cmux has selected the SDA pin rather than SPI NOR data-in. This couldn't
be avoided in any case, the board is not designed to allow concurrent
i2c3 and SPI NOR functions (and the default device-tree does not enable
SPI NOR anyway).

Devices hanging off i2c3 should now be defined under i2cmux, so
that the steering pin can be properly controlled to access those
devices. The port expanders (MAX7310) are thus moved into i2cmux.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 65 +++++++++++++++++++++-----------
 1 file changed, 44 insertions(+), 21 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
index a2a714d..c8e35c4 100644
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
@@ -108,6 +108,44 @@
 		default-brightness-level = <7>;
 		status = "okay";
 	};
+
+	i2cmux {
+		compatible = "i2c-mux-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2c3mux>;
+		mux-gpios = <&gpio5 4 0>;
+		i2c-parent = <&i2c3>;
+		idle-state = <0>;
+
+		i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			max7310_a: gpio at 30 {
+				compatible = "maxim,max7310";
+				reg = <0x30>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			max7310_b: gpio at 32 {
+				compatible = "maxim,max7310";
+				reg = <0x32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			max7310_c: gpio at 34 {
+				compatible = "maxim,max7310";
+				reg = <0x34>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+		};
+	};
 };
 
 &clks {
@@ -290,27 +328,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c3>;
 	status = "okay";
-
-	max7310_a: gpio at 30 {
-		compatible = "maxim,max7310";
-		reg = <0x30>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	max7310_b: gpio at 32 {
-		compatible = "maxim,max7310";
-		reg = <0x32>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	max7310_c: gpio at 34 {
-		compatible = "maxim,max7310";
-		reg = <0x34>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
 };
 
 &iomuxc {
@@ -418,6 +435,12 @@
 			>;
 		};
 
+		pinctrl_i2c3mux: i2c3muxgrp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x0b0b1
+			>;
+		};
+
 		pinctrl_pwm3: pwm1grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
-- 
2.7.4

[PATCH v5 11/39] ARM: dts: imx6-sabreauto: add reset-gpios property for max7310_b

[Steve Longerbeam]

The reset pin to the port expander chip (MAX7310) is controlled by a gpio,
so define a reset-gpios property to control it. There are three MAX7310's
on the SabreAuto CPU card (max7310_[abc]), but all use the same pin for
their reset. Since all can't acquire the same pin, assign it to max7310_b,
that chip is needed by more functions (usb and adv7180).

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
index c8e35c4..21dea5f 100644
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
@@ -136,6 +136,9 @@
 				reg = <0x32>;
 				gpio-controller;
 				#gpio-cells = <2>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_max7310>;
+				reset-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
 			};
 
 			max7310_c: gpio@34 {
@@ -441,6 +444,12 @@
 			>;
 		};
 
+		pinctrl_max7310: max7310grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD2_DAT0__GPIO1_IO15 0x1b0b0
+			>;
+		};
+
 		pinctrl_pwm3: pwm1grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
-- 
2.7.4

[PATCH v5 11/39] ARM: dts: imx6-sabreauto: add reset-gpios property for max7310_b

[Steve Longerbeam]

The reset pin to the port expander chip (MAX7310) is controlled by a gpio,
so define a reset-gpios property to control it. There are three MAX7310's
on the SabreAuto CPU card (max7310_[abc]), but all use the same pin for
their reset. Since all can't acquire the same pin, assign it to max7310_b,
that chip is needed by more functions (usb and adv7180).

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
index c8e35c4..21dea5f 100644
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
@@ -136,6 +136,9 @@
 				reg = <0x32>;
 				gpio-controller;
 				#gpio-cells = <2>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_max7310>;
+				reset-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
 			};
 
 			max7310_c: gpio at 34 {
@@ -441,6 +444,12 @@
 			>;
 		};
 
+		pinctrl_max7310: max7310grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD2_DAT0__GPIO1_IO15 0x1b0b0
+			>;
+		};
+
 		pinctrl_pwm3: pwm1grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
-- 
2.7.4

[PATCH v5 12/39] ARM: dts: imx6-sabreauto: add pinctrl for gpt input capture

[Steve Longerbeam]

Add pinctrl groups for both GPT input capture channels.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
index 21dea5f..1212f82 100644
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
@@ -456,6 +456,18 @@
 			>;
 		};
 
+		pinctrl_gpt_input_capture0: gptinputcapture0grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT0__GPT_CAPTURE1	0x1b0b0
+			>;
+		};
+
+		pinctrl_gpt_input_capture1: gptinputcapture1grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT1__GPT_CAPTURE2	0x1b0b0
+			>;
+		};
+
 		pinctrl_spdif: spdifgrp {
 			fsl,pins = <
 				MX6QDL_PAD_KEY_COL3__SPDIF_IN 0x1b0b0
-- 
2.7.4

[PATCH v5 12/39] ARM: dts: imx6-sabreauto: add pinctrl for gpt input capture

[Steve Longerbeam]

Add pinctrl groups for both GPT input capture channels.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
index 21dea5f..1212f82 100644
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
@@ -456,6 +456,18 @@
 			>;
 		};
 
+		pinctrl_gpt_input_capture0: gptinputcapture0grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT0__GPT_CAPTURE1	0x1b0b0
+			>;
+		};
+
+		pinctrl_gpt_input_capture1: gptinputcapture1grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT1__GPT_CAPTURE2	0x1b0b0
+			>;
+		};
+
 		pinctrl_spdif: spdifgrp {
 			fsl,pins = <
 				MX6QDL_PAD_KEY_COL3__SPDIF_IN 0x1b0b0
-- 
2.7.4

[PATCH v5 12/39] ARM: dts: imx6-sabreauto: add pinctrl for gpt input capture

[Steve Longerbeam]

Add pinctrl groups for both GPT input capture channels.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
index 21dea5f..1212f82 100644
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
@@ -456,6 +456,18 @@
 			>;
 		};
 
+		pinctrl_gpt_input_capture0: gptinputcapture0grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT0__GPT_CAPTURE1	0x1b0b0
+			>;
+		};
+
+		pinctrl_gpt_input_capture1: gptinputcapture1grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT1__GPT_CAPTURE2	0x1b0b0
+			>;
+		};
+
 		pinctrl_spdif: spdifgrp {
 			fsl,pins = <
 				MX6QDL_PAD_KEY_COL3__SPDIF_IN 0x1b0b0
-- 
2.7.4

[PATCH v5 13/39] ARM: dts: imx6-sabreauto: add the ADV7180 video decoder

[Steve Longerbeam]

Enables the ADV7180 decoder sensor. The ADV7180 connects to the
parallel-bus mux input on ipu1_csi0_mux.

The ADV7180 power pin is via max7310_b port expander.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 58 ++++++++++++++++++++++++++++++++
 1 file changed, 58 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
index 1212f82..a712ff1 100644
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
@@ -124,6 +124,21 @@
 			#size-cells = <0>;
 			reg = <1>;
 
+			adv7180: camera@21 {
+				compatible = "adi,adv7180";
+				reg = <0x21>;
+				powerdown-gpios = <&max7310_b 2 GPIO_ACTIVE_LOW>;
+				interrupt-parent = <&gpio1>;
+				interrupts = <27 0x8>;
+
+				port {
+					adv7180_to_ipu1_csi0_mux: endpoint {
+						remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+						bus-width = <8>;
+					};
+				};
+			};
+
 			max7310_a: gpio@30 {
 				compatible = "maxim,max7310";
 				reg = <0x30>;
@@ -151,6 +166,25 @@
 	};
 };
 
+&ipu1_csi0_from_ipu1_csi0_mux {
+	bus-width = <8>;
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+	remote-endpoint = <&adv7180_to_ipu1_csi0_mux>;
+	bus-width = <8>;
+};
+
+&ipu1_csi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ipu1_csi0>;
+
+	/* enable frame interval monitor on this port */
+	fim {
+		status = "okay";
+	};
+};
+
 &clks {
 	assigned-clocks = <&clks IMX6QDL_PLL4_BYPASS_SRC>,
 			  <&clks IMX6QDL_PLL4_BYPASS>,
@@ -444,6 +478,30 @@
 			>;
 		};
 
+		pinctrl_ipu1_csi0: ipu1csi0grp {
+			fsl,pins = <
+				MX6QDL_PAD_CSI0_DAT4__IPU1_CSI0_DATA04   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT5__IPU1_CSI0_DATA05   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT6__IPU1_CSI0_DATA06   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT7__IPU1_CSI0_DATA07   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT8__IPU1_CSI0_DATA08   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT9__IPU1_CSI0_DATA09   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT10__IPU1_CSI0_DATA10  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT11__IPU1_CSI0_DATA11  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19  0x1b0b0
+				MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
+				MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC    0x1b0b0
+				MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC   0x1b0b0
+			>;
+		};
+
 		pinctrl_max7310: max7310grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD2_DAT0__GPIO1_IO15 0x1b0b0
-- 
2.7.4

[PATCH v5 13/39] ARM: dts: imx6-sabreauto: add the ADV7180 video decoder

[Steve Longerbeam]

Enables the ADV7180 decoder sensor. The ADV7180 connects to the
parallel-bus mux input on ipu1_csi0_mux.

The ADV7180 power pin is via max7310_b port expander.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 58 ++++++++++++++++++++++++++++++++
 1 file changed, 58 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
index 1212f82..a712ff1 100644
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
@@ -124,6 +124,21 @@
 			#size-cells = <0>;
 			reg = <1>;
 
+			adv7180: camera at 21 {
+				compatible = "adi,adv7180";
+				reg = <0x21>;
+				powerdown-gpios = <&max7310_b 2 GPIO_ACTIVE_LOW>;
+				interrupt-parent = <&gpio1>;
+				interrupts = <27 0x8>;
+
+				port {
+					adv7180_to_ipu1_csi0_mux: endpoint {
+						remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+						bus-width = <8>;
+					};
+				};
+			};
+
 			max7310_a: gpio at 30 {
 				compatible = "maxim,max7310";
 				reg = <0x30>;
@@ -151,6 +166,25 @@
 	};
 };
 
+&ipu1_csi0_from_ipu1_csi0_mux {
+	bus-width = <8>;
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+	remote-endpoint = <&adv7180_to_ipu1_csi0_mux>;
+	bus-width = <8>;
+};
+
+&ipu1_csi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ipu1_csi0>;
+
+	/* enable frame interval monitor on this port */
+	fim {
+		status = "okay";
+	};
+};
+
 &clks {
 	assigned-clocks = <&clks IMX6QDL_PLL4_BYPASS_SRC>,
 			  <&clks IMX6QDL_PLL4_BYPASS>,
@@ -444,6 +478,30 @@
 			>;
 		};
 
+		pinctrl_ipu1_csi0: ipu1csi0grp {
+			fsl,pins = <
+				MX6QDL_PAD_CSI0_DAT4__IPU1_CSI0_DATA04   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT5__IPU1_CSI0_DATA05   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT6__IPU1_CSI0_DATA06   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT7__IPU1_CSI0_DATA07   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT8__IPU1_CSI0_DATA08   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT9__IPU1_CSI0_DATA09   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT10__IPU1_CSI0_DATA10  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT11__IPU1_CSI0_DATA11  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19  0x1b0b0
+				MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
+				MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC    0x1b0b0
+				MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC   0x1b0b0
+			>;
+		};
+
 		pinctrl_max7310: max7310grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD2_DAT0__GPIO1_IO15 0x1b0b0
-- 
2.7.4

[PATCH v5 13/39] ARM: dts: imx6-sabreauto: add the ADV7180 video decoder

[Steve Longerbeam]

Enables the ADV7180 decoder sensor. The ADV7180 connects to the
parallel-bus mux input on ipu1_csi0_mux.

The ADV7180 power pin is via max7310_b port expander.

Signed-off-by: Steve Longerbeam <steve_longerbeam-nmGgyN9QBj3QT0dZR+AlfA@public.gmane.org>
---
 arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 58 ++++++++++++++++++++++++++++++++
 1 file changed, 58 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
index 1212f82..a712ff1 100644
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
@@ -124,6 +124,21 @@
 			#size-cells = <0>;
 			reg = <1>;
 
+			adv7180: camera@21 {
+				compatible = "adi,adv7180";
+				reg = <0x21>;
+				powerdown-gpios = <&max7310_b 2 GPIO_ACTIVE_LOW>;
+				interrupt-parent = <&gpio1>;
+				interrupts = <27 0x8>;
+
+				port {
+					adv7180_to_ipu1_csi0_mux: endpoint {
+						remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+						bus-width = <8>;
+					};
+				};
+			};
+
 			max7310_a: gpio@30 {
 				compatible = "maxim,max7310";
 				reg = <0x30>;
@@ -151,6 +166,25 @@
 	};
 };
 
+&ipu1_csi0_from_ipu1_csi0_mux {
+	bus-width = <8>;
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+	remote-endpoint = <&adv7180_to_ipu1_csi0_mux>;
+	bus-width = <8>;
+};
+
+&ipu1_csi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ipu1_csi0>;
+
+	/* enable frame interval monitor on this port */
+	fim {
+		status = "okay";
+	};
+};
+
 &clks {
 	assigned-clocks = <&clks IMX6QDL_PLL4_BYPASS_SRC>,
 			  <&clks IMX6QDL_PLL4_BYPASS>,
@@ -444,6 +478,30 @@
 			>;
 		};
 
+		pinctrl_ipu1_csi0: ipu1csi0grp {
+			fsl,pins = <
+				MX6QDL_PAD_CSI0_DAT4__IPU1_CSI0_DATA04   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT5__IPU1_CSI0_DATA05   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT6__IPU1_CSI0_DATA06   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT7__IPU1_CSI0_DATA07   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT8__IPU1_CSI0_DATA08   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT9__IPU1_CSI0_DATA09   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT10__IPU1_CSI0_DATA10  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT11__IPU1_CSI0_DATA11  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19  0x1b0b0
+				MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
+				MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC    0x1b0b0
+				MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC   0x1b0b0
+			>;
+		};
+
 		pinctrl_max7310: max7310grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD2_DAT0__GPIO1_IO15 0x1b0b0
-- 
2.7.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v5 14/39] add mux and video interface bridge entity functions

[Steve Longerbeam]

From: Philipp Zabel <p.zabel@pengutronix.de>

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>

- renamed MEDIA_ENT_F_MUX to MEDIA_ENT_F_VID_MUX

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 Documentation/media/uapi/mediactl/media-types.rst | 22 ++++++++++++++++++++++
 include/uapi/linux/media.h                        |  6 ++++++
 2 files changed, 28 insertions(+)

diff --git a/Documentation/media/uapi/mediactl/media-types.rst b/Documentation/media/uapi/mediactl/media-types.rst
index 3e03dc2..9d908fe 100644
--- a/Documentation/media/uapi/mediactl/media-types.rst
+++ b/Documentation/media/uapi/mediactl/media-types.rst
@@ -298,6 +298,28 @@ Types and flags used to represent the media graph elements
 	  received on its sink pad and outputs the statistics data on
 	  its source pad.
 
+    -  ..  row 29
+
+       ..  _MEDIA-ENT-F-VID-MUX:
+
+       -  ``MEDIA_ENT_F_VID_MUX``
+
+       - Video multiplexer. An entity capable of multiplexing must have at
+         least two sink pads and one source pad, and must pass the video
+         frame(s) received from the active sink pad to the source pad. Video
+         frame(s) from the inactive sink pads are discarded.
+
+    -  ..  row 30
+
+       ..  _MEDIA-ENT-F-VID-IF-BRIDGE:
+
+       -  ``MEDIA_ENT_F_VID_IF_BRIDGE``
+
+       - Video interface bridge. A video interface bridge entity must have at
+         least one sink pad and one source pad. It receives video frame(s) on
+         its sink pad in one bus format (HDMI, eDP, MIPI CSI-2, ...) and
+         converts them and outputs them on its source pad in another bus format
+         (eDP, MIPI CSI-2, parallel, ...).
 
 ..  tabularcolumns:: |p{5.5cm}|p{12.0cm}|
 
diff --git a/include/uapi/linux/media.h b/include/uapi/linux/media.h
index 4890787..fac96c6 100644
--- a/include/uapi/linux/media.h
+++ b/include/uapi/linux/media.h
@@ -105,6 +105,12 @@ struct media_device_info {
 #define MEDIA_ENT_F_PROC_VIDEO_STATISTICS	(MEDIA_ENT_F_BASE + 0x4006)
 
 /*
+ * Switch and bridge entitites
+ */
+#define MEDIA_ENT_F_VID_MUX			(MEDIA_ENT_F_BASE + 0x5001)
+#define MEDIA_ENT_F_VID_IF_BRIDGE		(MEDIA_ENT_F_BASE + 0x5002)
+
+/*
  * Connectors
  */
 /* It is a responsibility of the entity drivers to add connectors and links */
-- 
2.7.4

[PATCH v5 14/39] add mux and video interface bridge entity functions

[Steve Longerbeam]

From: Philipp Zabel <p.zabel@pengutronix.de>

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>

- renamed MEDIA_ENT_F_MUX to MEDIA_ENT_F_VID_MUX

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 Documentation/media/uapi/mediactl/media-types.rst | 22 ++++++++++++++++++++++
 include/uapi/linux/media.h                        |  6 ++++++
 2 files changed, 28 insertions(+)

diff --git a/Documentation/media/uapi/mediactl/media-types.rst b/Documentation/media/uapi/mediactl/media-types.rst
index 3e03dc2..9d908fe 100644
--- a/Documentation/media/uapi/mediactl/media-types.rst
+++ b/Documentation/media/uapi/mediactl/media-types.rst
@@ -298,6 +298,28 @@ Types and flags used to represent the media graph elements
 	  received on its sink pad and outputs the statistics data on
 	  its source pad.
 
+    -  ..  row 29
+
+       ..  _MEDIA-ENT-F-VID-MUX:
+
+       -  ``MEDIA_ENT_F_VID_MUX``
+
+       - Video multiplexer. An entity capable of multiplexing must have at
+         least two sink pads and one source pad, and must pass the video
+         frame(s) received from the active sink pad to the source pad. Video
+         frame(s) from the inactive sink pads are discarded.
+
+    -  ..  row 30
+
+       ..  _MEDIA-ENT-F-VID-IF-BRIDGE:
+
+       -  ``MEDIA_ENT_F_VID_IF_BRIDGE``
+
+       - Video interface bridge. A video interface bridge entity must have at
+         least one sink pad and one source pad. It receives video frame(s) on
+         its sink pad in one bus format (HDMI, eDP, MIPI CSI-2, ...) and
+         converts them and outputs them on its source pad in another bus format
+         (eDP, MIPI CSI-2, parallel, ...).
 
 ..  tabularcolumns:: |p{5.5cm}|p{12.0cm}|
 
diff --git a/include/uapi/linux/media.h b/include/uapi/linux/media.h
index 4890787..fac96c6 100644
--- a/include/uapi/linux/media.h
+++ b/include/uapi/linux/media.h
@@ -105,6 +105,12 @@ struct media_device_info {
 #define MEDIA_ENT_F_PROC_VIDEO_STATISTICS	(MEDIA_ENT_F_BASE + 0x4006)
 
 /*
+ * Switch and bridge entitites
+ */
+#define MEDIA_ENT_F_VID_MUX			(MEDIA_ENT_F_BASE + 0x5001)
+#define MEDIA_ENT_F_VID_IF_BRIDGE		(MEDIA_ENT_F_BASE + 0x5002)
+
+/*
  * Connectors
  */
 /* It is a responsibility of the entity drivers to add connectors and links */
-- 
2.7.4

[PATCH v5 14/39] add mux and video interface bridge entity functions

[Steve Longerbeam]

From: Philipp Zabel <p.zabel@pengutronix.de>

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>

- renamed MEDIA_ENT_F_MUX to MEDIA_ENT_F_VID_MUX

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 Documentation/media/uapi/mediactl/media-types.rst | 22 ++++++++++++++++++++++
 include/uapi/linux/media.h                        |  6 ++++++
 2 files changed, 28 insertions(+)

diff --git a/Documentation/media/uapi/mediactl/media-types.rst b/Documentation/media/uapi/mediactl/media-types.rst
index 3e03dc2..9d908fe 100644
--- a/Documentation/media/uapi/mediactl/media-types.rst
+++ b/Documentation/media/uapi/mediactl/media-types.rst
@@ -298,6 +298,28 @@ Types and flags used to represent the media graph elements
 	  received on its sink pad and outputs the statistics data on
 	  its source pad.
 
+    -  ..  row 29
+
+       ..  _MEDIA-ENT-F-VID-MUX:
+
+       -  ``MEDIA_ENT_F_VID_MUX``
+
+       - Video multiplexer. An entity capable of multiplexing must have at
+         least two sink pads and one source pad, and must pass the video
+         frame(s) received from the active sink pad to the source pad. Video
+         frame(s) from the inactive sink pads are discarded.
+
+    -  ..  row 30
+
+       ..  _MEDIA-ENT-F-VID-IF-BRIDGE:
+
+       -  ``MEDIA_ENT_F_VID_IF_BRIDGE``
+
+       - Video interface bridge. A video interface bridge entity must have at
+         least one sink pad and one source pad. It receives video frame(s) on
+         its sink pad in one bus format (HDMI, eDP, MIPI CSI-2, ...) and
+         converts them and outputs them on its source pad in another bus format
+         (eDP, MIPI CSI-2, parallel, ...).
 
 ..  tabularcolumns:: |p{5.5cm}|p{12.0cm}|
 
diff --git a/include/uapi/linux/media.h b/include/uapi/linux/media.h
index 4890787..fac96c6 100644
--- a/include/uapi/linux/media.h
+++ b/include/uapi/linux/media.h
@@ -105,6 +105,12 @@ struct media_device_info {
 #define MEDIA_ENT_F_PROC_VIDEO_STATISTICS	(MEDIA_ENT_F_BASE + 0x4006)
 
 /*
+ * Switch and bridge entitites
+ */
+#define MEDIA_ENT_F_VID_MUX			(MEDIA_ENT_F_BASE + 0x5001)
+#define MEDIA_ENT_F_VID_IF_BRIDGE		(MEDIA_ENT_F_BASE + 0x5002)
+
+/*
  * Connectors
  */
 /* It is a responsibility of the entity drivers to add connectors and links */
-- 
2.7.4

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

Add a new FRAME_INTERVAL_ERROR event to signal that a video capture or
output device has measured an interval between the reception or transmit
completion of two consecutive frames of video that is outside the nominal
frame interval by some tolerance value.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 Documentation/media/uapi/v4l/vidioc-dqevent.rst | 6 ++++++
 Documentation/media/videodev2.h.rst.exceptions  | 1 +
 include/uapi/linux/videodev2.h                  | 1 +
 3 files changed, 8 insertions(+)

diff --git a/Documentation/media/uapi/v4l/vidioc-dqevent.rst b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
index 8d663a7..dc77363 100644
--- a/Documentation/media/uapi/v4l/vidioc-dqevent.rst
+++ b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
@@ -197,6 +197,12 @@ call.
 	the regions changes. This event has a struct
 	:c:type:`v4l2_event_motion_det`
 	associated with it.
+    * - ``V4L2_EVENT_FRAME_INTERVAL_ERROR``
+      - 7
+      - This event is triggered when the video capture or output device
+	has measured an interval between the reception or transmit
+	completion of two consecutive frames of video that is outside
+	the nominal frame interval by some tolerance value.
     * - ``V4L2_EVENT_PRIVATE_START``
       - 0x08000000
       - Base event number for driver-private events.
diff --git a/Documentation/media/videodev2.h.rst.exceptions b/Documentation/media/videodev2.h.rst.exceptions
index e11a0d0..c7d8fad 100644
--- a/Documentation/media/videodev2.h.rst.exceptions
+++ b/Documentation/media/videodev2.h.rst.exceptions
@@ -459,6 +459,7 @@ replace define V4L2_EVENT_CTRL event-type
 replace define V4L2_EVENT_FRAME_SYNC event-type
 replace define V4L2_EVENT_SOURCE_CHANGE event-type
 replace define V4L2_EVENT_MOTION_DET event-type
+replace define V4L2_EVENT_FRAME_INTERVAL_ERROR event-type
 replace define V4L2_EVENT_PRIVATE_START event-type
 
 replace define V4L2_EVENT_CTRL_CH_VALUE ctrl-changes-flags
diff --git a/include/uapi/linux/videodev2.h b/include/uapi/linux/videodev2.h
index 45184a2..cf5a0d0 100644
--- a/include/uapi/linux/videodev2.h
+++ b/include/uapi/linux/videodev2.h
@@ -2131,6 +2131,7 @@ struct v4l2_streamparm {
 #define V4L2_EVENT_FRAME_SYNC			4
 #define V4L2_EVENT_SOURCE_CHANGE		5
 #define V4L2_EVENT_MOTION_DET			6
+#define V4L2_EVENT_FRAME_INTERVAL_ERROR		7
 #define V4L2_EVENT_PRIVATE_START		0x08000000
 
 /* Payload for V4L2_EVENT_VSYNC */
-- 
2.7.4

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

Add a new FRAME_INTERVAL_ERROR event to signal that a video capture or
output device has measured an interval between the reception or transmit
completion of two consecutive frames of video that is outside the nominal
frame interval by some tolerance value.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 Documentation/media/uapi/v4l/vidioc-dqevent.rst | 6 ++++++
 Documentation/media/videodev2.h.rst.exceptions  | 1 +
 include/uapi/linux/videodev2.h                  | 1 +
 3 files changed, 8 insertions(+)

diff --git a/Documentation/media/uapi/v4l/vidioc-dqevent.rst b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
index 8d663a7..dc77363 100644
--- a/Documentation/media/uapi/v4l/vidioc-dqevent.rst
+++ b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
@@ -197,6 +197,12 @@ call.
 	the regions changes. This event has a struct
 	:c:type:`v4l2_event_motion_det`
 	associated with it.
+    * - ``V4L2_EVENT_FRAME_INTERVAL_ERROR``
+      - 7
+      - This event is triggered when the video capture or output device
+	has measured an interval between the reception or transmit
+	completion of two consecutive frames of video that is outside
+	the nominal frame interval by some tolerance value.
     * - ``V4L2_EVENT_PRIVATE_START``
       - 0x08000000
       - Base event number for driver-private events.
diff --git a/Documentation/media/videodev2.h.rst.exceptions b/Documentation/media/videodev2.h.rst.exceptions
index e11a0d0..c7d8fad 100644
--- a/Documentation/media/videodev2.h.rst.exceptions
+++ b/Documentation/media/videodev2.h.rst.exceptions
@@ -459,6 +459,7 @@ replace define V4L2_EVENT_CTRL event-type
 replace define V4L2_EVENT_FRAME_SYNC event-type
 replace define V4L2_EVENT_SOURCE_CHANGE event-type
 replace define V4L2_EVENT_MOTION_DET event-type
+replace define V4L2_EVENT_FRAME_INTERVAL_ERROR event-type
 replace define V4L2_EVENT_PRIVATE_START event-type
 
 replace define V4L2_EVENT_CTRL_CH_VALUE ctrl-changes-flags
diff --git a/include/uapi/linux/videodev2.h b/include/uapi/linux/videodev2.h
index 45184a2..cf5a0d0 100644
--- a/include/uapi/linux/videodev2.h
+++ b/include/uapi/linux/videodev2.h
@@ -2131,6 +2131,7 @@ struct v4l2_streamparm {
 #define V4L2_EVENT_FRAME_SYNC			4
 #define V4L2_EVENT_SOURCE_CHANGE		5
 #define V4L2_EVENT_MOTION_DET			6
+#define V4L2_EVENT_FRAME_INTERVAL_ERROR		7
 #define V4L2_EVENT_PRIVATE_START		0x08000000
 
 /* Payload for V4L2_EVENT_VSYNC */
-- 
2.7.4

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Hans Verkuil]

On 10/03/17 05:52, Steve Longerbeam wrote:
> Add a new FRAME_INTERVAL_ERROR event to signal that a video capture or
> output device has measured an interval between the reception or transmit
> completion of two consecutive frames of video that is outside the nominal
> frame interval by some tolerance value.

Reading back what was said on this I agree with Sakari that this doesn't
belong here.

Userspace can detect this just as easily (if not easier) with a timeout.

Regards,

	Hans

> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> ---
>  Documentation/media/uapi/v4l/vidioc-dqevent.rst | 6 ++++++
>  Documentation/media/videodev2.h.rst.exceptions  | 1 +
>  include/uapi/linux/videodev2.h                  | 1 +
>  3 files changed, 8 insertions(+)
> 
> diff --git a/Documentation/media/uapi/v4l/vidioc-dqevent.rst b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
> index 8d663a7..dc77363 100644
> --- a/Documentation/media/uapi/v4l/vidioc-dqevent.rst
> +++ b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
> @@ -197,6 +197,12 @@ call.
>  	the regions changes. This event has a struct
>  	:c:type:`v4l2_event_motion_det`
>  	associated with it.
> +    * - ``V4L2_EVENT_FRAME_INTERVAL_ERROR``
> +      - 7
> +      - This event is triggered when the video capture or output device
> +	has measured an interval between the reception or transmit
> +	completion of two consecutive frames of video that is outside
> +	the nominal frame interval by some tolerance value.
>      * - ``V4L2_EVENT_PRIVATE_START``
>        - 0x08000000
>        - Base event number for driver-private events.
> diff --git a/Documentation/media/videodev2.h.rst.exceptions b/Documentation/media/videodev2.h.rst.exceptions
> index e11a0d0..c7d8fad 100644
> --- a/Documentation/media/videodev2.h.rst.exceptions
> +++ b/Documentation/media/videodev2.h.rst.exceptions
> @@ -459,6 +459,7 @@ replace define V4L2_EVENT_CTRL event-type
>  replace define V4L2_EVENT_FRAME_SYNC event-type
>  replace define V4L2_EVENT_SOURCE_CHANGE event-type
>  replace define V4L2_EVENT_MOTION_DET event-type
> +replace define V4L2_EVENT_FRAME_INTERVAL_ERROR event-type
>  replace define V4L2_EVENT_PRIVATE_START event-type
>  
>  replace define V4L2_EVENT_CTRL_CH_VALUE ctrl-changes-flags
> diff --git a/include/uapi/linux/videodev2.h b/include/uapi/linux/videodev2.h
> index 45184a2..cf5a0d0 100644
> --- a/include/uapi/linux/videodev2.h
> +++ b/include/uapi/linux/videodev2.h
> @@ -2131,6 +2131,7 @@ struct v4l2_streamparm {
>  #define V4L2_EVENT_FRAME_SYNC			4
>  #define V4L2_EVENT_SOURCE_CHANGE		5
>  #define V4L2_EVENT_MOTION_DET			6
> +#define V4L2_EVENT_FRAME_INTERVAL_ERROR		7
>  #define V4L2_EVENT_PRIVATE_START		0x08000000
>  
>  /* Payload for V4L2_EVENT_VSYNC */
> 

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Hans Verkuil]

On 10/03/17 05:52, Steve Longerbeam wrote:
> Add a new FRAME_INTERVAL_ERROR event to signal that a video capture or
> output device has measured an interval between the reception or transmit
> completion of two consecutive frames of video that is outside the nominal
> frame interval by some tolerance value.

Reading back what was said on this I agree with Sakari that this doesn't
belong here.

Userspace can detect this just as easily (if not easier) with a timeout.

Regards,

	Hans

> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> ---
>  Documentation/media/uapi/v4l/vidioc-dqevent.rst | 6 ++++++
>  Documentation/media/videodev2.h.rst.exceptions  | 1 +
>  include/uapi/linux/videodev2.h                  | 1 +
>  3 files changed, 8 insertions(+)
> 
> diff --git a/Documentation/media/uapi/v4l/vidioc-dqevent.rst b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
> index 8d663a7..dc77363 100644
> --- a/Documentation/media/uapi/v4l/vidioc-dqevent.rst
> +++ b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
> @@ -197,6 +197,12 @@ call.
>  	the regions changes. This event has a struct
>  	:c:type:`v4l2_event_motion_det`
>  	associated with it.
> +    * - ``V4L2_EVENT_FRAME_INTERVAL_ERROR``
> +      - 7
> +      - This event is triggered when the video capture or output device
> +	has measured an interval between the reception or transmit
> +	completion of two consecutive frames of video that is outside
> +	the nominal frame interval by some tolerance value.
>      * - ``V4L2_EVENT_PRIVATE_START``
>        - 0x08000000
>        - Base event number for driver-private events.
> diff --git a/Documentation/media/videodev2.h.rst.exceptions b/Documentation/media/videodev2.h.rst.exceptions
> index e11a0d0..c7d8fad 100644
> --- a/Documentation/media/videodev2.h.rst.exceptions
> +++ b/Documentation/media/videodev2.h.rst.exceptions
> @@ -459,6 +459,7 @@ replace define V4L2_EVENT_CTRL event-type
>  replace define V4L2_EVENT_FRAME_SYNC event-type
>  replace define V4L2_EVENT_SOURCE_CHANGE event-type
>  replace define V4L2_EVENT_MOTION_DET event-type
> +replace define V4L2_EVENT_FRAME_INTERVAL_ERROR event-type
>  replace define V4L2_EVENT_PRIVATE_START event-type
>  
>  replace define V4L2_EVENT_CTRL_CH_VALUE ctrl-changes-flags
> diff --git a/include/uapi/linux/videodev2.h b/include/uapi/linux/videodev2.h
> index 45184a2..cf5a0d0 100644
> --- a/include/uapi/linux/videodev2.h
> +++ b/include/uapi/linux/videodev2.h
> @@ -2131,6 +2131,7 @@ struct v4l2_streamparm {
>  #define V4L2_EVENT_FRAME_SYNC			4
>  #define V4L2_EVENT_SOURCE_CHANGE		5
>  #define V4L2_EVENT_MOTION_DET			6
> +#define V4L2_EVENT_FRAME_INTERVAL_ERROR		7
>  #define V4L2_EVENT_PRIVATE_START		0x08000000
>  
>  /* Payload for V4L2_EVENT_VSYNC */
> 

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Hans Verkuil]

On 10/03/17 05:52, Steve Longerbeam wrote:
> Add a new FRAME_INTERVAL_ERROR event to signal that a video capture or
> output device has measured an interval between the reception or transmit
> completion of two consecutive frames of video that is outside the nominal
> frame interval by some tolerance value.

Reading back what was said on this I agree with Sakari that this doesn't
belong here.

Userspace can detect this just as easily (if not easier) with a timeout.

Regards,

	Hans

> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> ---
>  Documentation/media/uapi/v4l/vidioc-dqevent.rst | 6 ++++++
>  Documentation/media/videodev2.h.rst.exceptions  | 1 +
>  include/uapi/linux/videodev2.h                  | 1 +
>  3 files changed, 8 insertions(+)
> 
> diff --git a/Documentation/media/uapi/v4l/vidioc-dqevent.rst b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
> index 8d663a7..dc77363 100644
> --- a/Documentation/media/uapi/v4l/vidioc-dqevent.rst
> +++ b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
> @@ -197,6 +197,12 @@ call.
>  	the regions changes. This event has a struct
>  	:c:type:`v4l2_event_motion_det`
>  	associated with it.
> +    * - ``V4L2_EVENT_FRAME_INTERVAL_ERROR``
> +      - 7
> +      - This event is triggered when the video capture or output device
> +	has measured an interval between the reception or transmit
> +	completion of two consecutive frames of video that is outside
> +	the nominal frame interval by some tolerance value.
>      * - ``V4L2_EVENT_PRIVATE_START``
>        - 0x08000000
>        - Base event number for driver-private events.
> diff --git a/Documentation/media/videodev2.h.rst.exceptions b/Documentation/media/videodev2.h.rst.exceptions
> index e11a0d0..c7d8fad 100644
> --- a/Documentation/media/videodev2.h.rst.exceptions
> +++ b/Documentation/media/videodev2.h.rst.exceptions
> @@ -459,6 +459,7 @@ replace define V4L2_EVENT_CTRL event-type
>  replace define V4L2_EVENT_FRAME_SYNC event-type
>  replace define V4L2_EVENT_SOURCE_CHANGE event-type
>  replace define V4L2_EVENT_MOTION_DET event-type
> +replace define V4L2_EVENT_FRAME_INTERVAL_ERROR event-type
>  replace define V4L2_EVENT_PRIVATE_START event-type
>  
>  replace define V4L2_EVENT_CTRL_CH_VALUE ctrl-changes-flags
> diff --git a/include/uapi/linux/videodev2.h b/include/uapi/linux/videodev2.h
> index 45184a2..cf5a0d0 100644
> --- a/include/uapi/linux/videodev2.h
> +++ b/include/uapi/linux/videodev2.h
> @@ -2131,6 +2131,7 @@ struct v4l2_streamparm {
>  #define V4L2_EVENT_FRAME_SYNC			4
>  #define V4L2_EVENT_SOURCE_CHANGE		5
>  #define V4L2_EVENT_MOTION_DET			6
> +#define V4L2_EVENT_FRAME_INTERVAL_ERROR		7
>  #define V4L2_EVENT_PRIVATE_START		0x08000000
>  
>  /* Payload for V4L2_EVENT_VSYNC */
> 

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

Hi Hans,

On 03/10/2017 04:03 AM, Hans Verkuil wrote:
> On 10/03/17 05:52, Steve Longerbeam wrote:
>> Add a new FRAME_INTERVAL_ERROR event to signal that a video capture or
>> output device has measured an interval between the reception or transmit
>> completion of two consecutive frames of video that is outside the nominal
>> frame interval by some tolerance value.
>
> Reading back what was said on this I agree with Sakari that this doesn't
> belong here.
>
> Userspace can detect this just as easily (if not easier) with a timeout.
>


Unfortunately measuring frame intervals from userland is not accurate
enough for i.MX6.

The issue here is that the IPUv3, specifically the CSI unit, can
permanently lose vertical sync if there are truncated frames sent
on the bt.656 bus. We have seen a single missing line of video cause
loss of vertical sync. The only way to correct this is to shutdown
the IPU capture hardware and restart, which can be accomplished
simply by restarting streaming from userland.

There are no other indicators from the sensor about these short
frame events (believe me, we've exhausted all avenues with the ADV718x).
And the IPUv3 DMA engine has no status indicators for short frames
either. So the only way to detect them is by measuring frame intervals.

The intervals have to be able to resolve a single line of missing video.
With a PAL video source that requires better than 58 usec accuracy.

There is too much uncertainty to resolve this at user level. The
driver is able to resolve this by measuring intervals between hardware
interrupts as long as interrupt latency is reasonably low, and we
have another method using the i.MX6 hardware input capture support
that can measure these intervals very accurately with no errors
introduced by interrupt latency.

I made this event a private event to imx-media driver in a previous
iteration, so I can return it to a private event, but this can't be
done at user level.

Steve


>
>>
>> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
>> ---
>>  Documentation/media/uapi/v4l/vidioc-dqevent.rst | 6 ++++++
>>  Documentation/media/videodev2.h.rst.exceptions  | 1 +
>>  include/uapi/linux/videodev2.h                  | 1 +
>>  3 files changed, 8 insertions(+)
>>
>> diff --git a/Documentation/media/uapi/v4l/vidioc-dqevent.rst b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
>> index 8d663a7..dc77363 100644
>> --- a/Documentation/media/uapi/v4l/vidioc-dqevent.rst
>> +++ b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
>> @@ -197,6 +197,12 @@ call.
>>  	the regions changes. This event has a struct
>>  	:c:type:`v4l2_event_motion_det`
>>  	associated with it.
>> +    * - ``V4L2_EVENT_FRAME_INTERVAL_ERROR``
>> +      - 7
>> +      - This event is triggered when the video capture or output device
>> +	has measured an interval between the reception or transmit
>> +	completion of two consecutive frames of video that is outside
>> +	the nominal frame interval by some tolerance value.
>>      * - ``V4L2_EVENT_PRIVATE_START``
>>        - 0x08000000
>>        - Base event number for driver-private events.
>> diff --git a/Documentation/media/videodev2.h.rst.exceptions b/Documentation/media/videodev2.h.rst.exceptions
>> index e11a0d0..c7d8fad 100644
>> --- a/Documentation/media/videodev2.h.rst.exceptions
>> +++ b/Documentation/media/videodev2.h.rst.exceptions
>> @@ -459,6 +459,7 @@ replace define V4L2_EVENT_CTRL event-type
>>  replace define V4L2_EVENT_FRAME_SYNC event-type
>>  replace define V4L2_EVENT_SOURCE_CHANGE event-type
>>  replace define V4L2_EVENT_MOTION_DET event-type
>> +replace define V4L2_EVENT_FRAME_INTERVAL_ERROR event-type
>>  replace define V4L2_EVENT_PRIVATE_START event-type
>>
>>  replace define V4L2_EVENT_CTRL_CH_VALUE ctrl-changes-flags
>> diff --git a/include/uapi/linux/videodev2.h b/include/uapi/linux/videodev2.h
>> index 45184a2..cf5a0d0 100644
>> --- a/include/uapi/linux/videodev2.h
>> +++ b/include/uapi/linux/videodev2.h
>> @@ -2131,6 +2131,7 @@ struct v4l2_streamparm {
>>  #define V4L2_EVENT_FRAME_SYNC			4
>>  #define V4L2_EVENT_SOURCE_CHANGE		5
>>  #define V4L2_EVENT_MOTION_DET			6
>> +#define V4L2_EVENT_FRAME_INTERVAL_ERROR		7
>>  #define V4L2_EVENT_PRIVATE_START		0x08000000
>>
>>  /* Payload for V4L2_EVENT_VSYNC */
>>
>

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

Hi Hans,

On 03/10/2017 04:03 AM, Hans Verkuil wrote:
> On 10/03/17 05:52, Steve Longerbeam wrote:
>> Add a new FRAME_INTERVAL_ERROR event to signal that a video capture or
>> output device has measured an interval between the reception or transmit
>> completion of two consecutive frames of video that is outside the nominal
>> frame interval by some tolerance value.
>
> Reading back what was said on this I agree with Sakari that this doesn't
> belong here.
>
> Userspace can detect this just as easily (if not easier) with a timeout.
>


Unfortunately measuring frame intervals from userland is not accurate
enough for i.MX6.

The issue here is that the IPUv3, specifically the CSI unit, can
permanently lose vertical sync if there are truncated frames sent
on the bt.656 bus. We have seen a single missing line of video cause
loss of vertical sync. The only way to correct this is to shutdown
the IPU capture hardware and restart, which can be accomplished
simply by restarting streaming from userland.

There are no other indicators from the sensor about these short
frame events (believe me, we've exhausted all avenues with the ADV718x).
And the IPUv3 DMA engine has no status indicators for short frames
either. So the only way to detect them is by measuring frame intervals.

The intervals have to be able to resolve a single line of missing video.
With a PAL video source that requires better than 58 usec accuracy.

There is too much uncertainty to resolve this at user level. The
driver is able to resolve this by measuring intervals between hardware
interrupts as long as interrupt latency is reasonably low, and we
have another method using the i.MX6 hardware input capture support
that can measure these intervals very accurately with no errors
introduced by interrupt latency.

I made this event a private event to imx-media driver in a previous
iteration, so I can return it to a private event, but this can't be
done at user level.

Steve


>
>>
>> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
>> ---
>>  Documentation/media/uapi/v4l/vidioc-dqevent.rst | 6 ++++++
>>  Documentation/media/videodev2.h.rst.exceptions  | 1 +
>>  include/uapi/linux/videodev2.h                  | 1 +
>>  3 files changed, 8 insertions(+)
>>
>> diff --git a/Documentation/media/uapi/v4l/vidioc-dqevent.rst b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
>> index 8d663a7..dc77363 100644
>> --- a/Documentation/media/uapi/v4l/vidioc-dqevent.rst
>> +++ b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
>> @@ -197,6 +197,12 @@ call.
>>  	the regions changes. This event has a struct
>>  	:c:type:`v4l2_event_motion_det`
>>  	associated with it.
>> +    * - ``V4L2_EVENT_FRAME_INTERVAL_ERROR``
>> +      - 7
>> +      - This event is triggered when the video capture or output device
>> +	has measured an interval between the reception or transmit
>> +	completion of two consecutive frames of video that is outside
>> +	the nominal frame interval by some tolerance value.
>>      * - ``V4L2_EVENT_PRIVATE_START``
>>        - 0x08000000
>>        - Base event number for driver-private events.
>> diff --git a/Documentation/media/videodev2.h.rst.exceptions b/Documentation/media/videodev2.h.rst.exceptions
>> index e11a0d0..c7d8fad 100644
>> --- a/Documentation/media/videodev2.h.rst.exceptions
>> +++ b/Documentation/media/videodev2.h.rst.exceptions
>> @@ -459,6 +459,7 @@ replace define V4L2_EVENT_CTRL event-type
>>  replace define V4L2_EVENT_FRAME_SYNC event-type
>>  replace define V4L2_EVENT_SOURCE_CHANGE event-type
>>  replace define V4L2_EVENT_MOTION_DET event-type
>> +replace define V4L2_EVENT_FRAME_INTERVAL_ERROR event-type
>>  replace define V4L2_EVENT_PRIVATE_START event-type
>>
>>  replace define V4L2_EVENT_CTRL_CH_VALUE ctrl-changes-flags
>> diff --git a/include/uapi/linux/videodev2.h b/include/uapi/linux/videodev2.h
>> index 45184a2..cf5a0d0 100644
>> --- a/include/uapi/linux/videodev2.h
>> +++ b/include/uapi/linux/videodev2.h
>> @@ -2131,6 +2131,7 @@ struct v4l2_streamparm {
>>  #define V4L2_EVENT_FRAME_SYNC			4
>>  #define V4L2_EVENT_SOURCE_CHANGE		5
>>  #define V4L2_EVENT_MOTION_DET			6
>> +#define V4L2_EVENT_FRAME_INTERVAL_ERROR		7
>>  #define V4L2_EVENT_PRIVATE_START		0x08000000
>>
>>  /* Payload for V4L2_EVENT_VSYNC */
>>
>

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 2210 bytes --]

On Fri 2017-03-10 10:37:21, Steve Longerbeam wrote:
> Hi Hans,
> 
> On 03/10/2017 04:03 AM, Hans Verkuil wrote:
> >On 10/03/17 05:52, Steve Longerbeam wrote:
> >>Add a new FRAME_INTERVAL_ERROR event to signal that a video capture or
> >>output device has measured an interval between the reception or transmit
> >>completion of two consecutive frames of video that is outside the nominal
> >>frame interval by some tolerance value.
> >
> >Reading back what was said on this I agree with Sakari that this doesn't
> >belong here.
> >
> >Userspace can detect this just as easily (if not easier) with a timeout.
> >
> 
> 
> Unfortunately measuring frame intervals from userland is not accurate
> enough for i.MX6.
> 
> The issue here is that the IPUv3, specifically the CSI unit, can
> permanently lose vertical sync if there are truncated frames sent
> on the bt.656 bus. We have seen a single missing line of video cause
> loss of vertical sync. The only way to correct this is to shutdown
> the IPU capture hardware and restart, which can be accomplished
> simply by restarting streaming from userland.
> 
> There are no other indicators from the sensor about these short
> frame events (believe me, we've exhausted all avenues with the ADV718x).
> And the IPUv3 DMA engine has no status indicators for short frames
> either. So the only way to detect them is by measuring frame intervals.
> 
> The intervals have to be able to resolve a single line of missing video.
> With a PAL video source that requires better than 58 usec accuracy.
> 
> There is too much uncertainty to resolve this at user level. The
> driver is able to resolve this by measuring intervals between hardware
> interrupts as long as interrupt latency is reasonably low, and we
> have another method using the i.MX6 hardware input capture support
> that can measure these intervals very accurately with no errors
> introduced by interrupt latency.

Requiring < 58 usec interrupt latency for correct operation is a
little too optimistic, no?
									Pavel
-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Pavel Machek]

On Fri 2017-03-10 10:37:21, Steve Longerbeam wrote:
> Hi Hans,
> 
> On 03/10/2017 04:03 AM, Hans Verkuil wrote:
> >On 10/03/17 05:52, Steve Longerbeam wrote:
> >>Add a new FRAME_INTERVAL_ERROR event to signal that a video capture or
> >>output device has measured an interval between the reception or transmit
> >>completion of two consecutive frames of video that is outside the nominal
> >>frame interval by some tolerance value.
> >
> >Reading back what was said on this I agree with Sakari that this doesn't
> >belong here.
> >
> >Userspace can detect this just as easily (if not easier) with a timeout.
> >
> 
> 
> Unfortunately measuring frame intervals from userland is not accurate
> enough for i.MX6.
> 
> The issue here is that the IPUv3, specifically the CSI unit, can
> permanently lose vertical sync if there are truncated frames sent
> on the bt.656 bus. We have seen a single missing line of video cause
> loss of vertical sync. The only way to correct this is to shutdown
> the IPU capture hardware and restart, which can be accomplished
> simply by restarting streaming from userland.
> 
> There are no other indicators from the sensor about these short
> frame events (believe me, we've exhausted all avenues with the ADV718x).
> And the IPUv3 DMA engine has no status indicators for short frames
> either. So the only way to detect them is by measuring frame intervals.
> 
> The intervals have to be able to resolve a single line of missing video.
> With a PAL video source that requires better than 58 usec accuracy.
> 
> There is too much uncertainty to resolve this at user level. The
> driver is able to resolve this by measuring intervals between hardware
> interrupts as long as interrupt latency is reasonably low, and we
> have another method using the i.MX6 hardware input capture support
> that can measure these intervals very accurately with no errors
> introduced by interrupt latency.

Requiring < 58 usec interrupt latency for correct operation is a
little too optimistic, no?
									Pavel
-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 181 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170311/c974b353/attachment-0001.sig>

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 2210 bytes --]

On Fri 2017-03-10 10:37:21, Steve Longerbeam wrote:
> Hi Hans,
> 
> On 03/10/2017 04:03 AM, Hans Verkuil wrote:
> >On 10/03/17 05:52, Steve Longerbeam wrote:
> >>Add a new FRAME_INTERVAL_ERROR event to signal that a video capture or
> >>output device has measured an interval between the reception or transmit
> >>completion of two consecutive frames of video that is outside the nominal
> >>frame interval by some tolerance value.
> >
> >Reading back what was said on this I agree with Sakari that this doesn't
> >belong here.
> >
> >Userspace can detect this just as easily (if not easier) with a timeout.
> >
> 
> 
> Unfortunately measuring frame intervals from userland is not accurate
> enough for i.MX6.
> 
> The issue here is that the IPUv3, specifically the CSI unit, can
> permanently lose vertical sync if there are truncated frames sent
> on the bt.656 bus. We have seen a single missing line of video cause
> loss of vertical sync. The only way to correct this is to shutdown
> the IPU capture hardware and restart, which can be accomplished
> simply by restarting streaming from userland.
> 
> There are no other indicators from the sensor about these short
> frame events (believe me, we've exhausted all avenues with the ADV718x).
> And the IPUv3 DMA engine has no status indicators for short frames
> either. So the only way to detect them is by measuring frame intervals.
> 
> The intervals have to be able to resolve a single line of missing video.
> With a PAL video source that requires better than 58 usec accuracy.
> 
> There is too much uncertainty to resolve this at user level. The
> driver is able to resolve this by measuring intervals between hardware
> interrupts as long as interrupt latency is reasonably low, and we
> have another method using the i.MX6 hardware input capture support
> that can measure these intervals very accurately with no errors
> introduced by interrupt latency.

Requiring < 58 usec interrupt latency for correct operation is a
little too optimistic, no?
									Pavel
-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/10/2017 03:30 PM, Pavel Machek wrote:
> On Fri 2017-03-10 10:37:21, Steve Longerbeam wrote:
>> Hi Hans,
>>
>> On 03/10/2017 04:03 AM, Hans Verkuil wrote:
>>> On 10/03/17 05:52, Steve Longerbeam wrote:
>>>> Add a new FRAME_INTERVAL_ERROR event to signal that a video capture or
>>>> output device has measured an interval between the reception or transmit
>>>> completion of two consecutive frames of video that is outside the nominal
>>>> frame interval by some tolerance value.
>>>
>>> Reading back what was said on this I agree with Sakari that this doesn't
>>> belong here.
>>>
>>> Userspace can detect this just as easily (if not easier) with a timeout.
>>>
>>
>>
>> Unfortunately measuring frame intervals from userland is not accurate
>> enough for i.MX6.
>>
>> The issue here is that the IPUv3, specifically the CSI unit, can
>> permanently lose vertical sync if there are truncated frames sent
>> on the bt.656 bus. We have seen a single missing line of video cause
>> loss of vertical sync. The only way to correct this is to shutdown
>> the IPU capture hardware and restart, which can be accomplished
>> simply by restarting streaming from userland.
>>
>> There are no other indicators from the sensor about these short
>> frame events (believe me, we've exhausted all avenues with the ADV718x).
>> And the IPUv3 DMA engine has no status indicators for short frames
>> either. So the only way to detect them is by measuring frame intervals.
>>
>> The intervals have to be able to resolve a single line of missing video.
>> With a PAL video source that requires better than 58 usec accuracy.
>>
>> There is too much uncertainty to resolve this at user level. The
>> driver is able to resolve this by measuring intervals between hardware
>> interrupts as long as interrupt latency is reasonably low, and we
>> have another method using the i.MX6 hardware input capture support
>> that can measure these intervals very accurately with no errors
>> introduced by interrupt latency.
>
> Requiring < 58 usec interrupt latency for correct operation is a
> little too optimistic, no?


No it's not too optimistic, from experience the imx6 kernel has irq
latency less than 10 usec under normal system load. False events can be
generated if the latency gets bad, it's true, and that's why there is
the imx6 timer input capture approach.

Steve

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/10/2017 03:30 PM, Pavel Machek wrote:
> On Fri 2017-03-10 10:37:21, Steve Longerbeam wrote:
>> Hi Hans,
>>
>> On 03/10/2017 04:03 AM, Hans Verkuil wrote:
>>> On 10/03/17 05:52, Steve Longerbeam wrote:
>>>> Add a new FRAME_INTERVAL_ERROR event to signal that a video capture or
>>>> output device has measured an interval between the reception or transmit
>>>> completion of two consecutive frames of video that is outside the nominal
>>>> frame interval by some tolerance value.
>>>
>>> Reading back what was said on this I agree with Sakari that this doesn't
>>> belong here.
>>>
>>> Userspace can detect this just as easily (if not easier) with a timeout.
>>>
>>
>>
>> Unfortunately measuring frame intervals from userland is not accurate
>> enough for i.MX6.
>>
>> The issue here is that the IPUv3, specifically the CSI unit, can
>> permanently lose vertical sync if there are truncated frames sent
>> on the bt.656 bus. We have seen a single missing line of video cause
>> loss of vertical sync. The only way to correct this is to shutdown
>> the IPU capture hardware and restart, which can be accomplished
>> simply by restarting streaming from userland.
>>
>> There are no other indicators from the sensor about these short
>> frame events (believe me, we've exhausted all avenues with the ADV718x).
>> And the IPUv3 DMA engine has no status indicators for short frames
>> either. So the only way to detect them is by measuring frame intervals.
>>
>> The intervals have to be able to resolve a single line of missing video.
>> With a PAL video source that requires better than 58 usec accuracy.
>>
>> There is too much uncertainty to resolve this at user level. The
>> driver is able to resolve this by measuring intervals between hardware
>> interrupts as long as interrupt latency is reasonably low, and we
>> have another method using the i.MX6 hardware input capture support
>> that can measure these intervals very accurately with no errors
>> introduced by interrupt latency.
>
> Requiring < 58 usec interrupt latency for correct operation is a
> little too optimistic, no?


No it's not too optimistic, from experience the imx6 kernel has irq
latency less than 10 usec under normal system load. False events can be
generated if the latency gets bad, it's true, and that's why there is
the imx6 timer input capture approach.

Steve

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/10/2017 03:30 PM, Pavel Machek wrote:
> On Fri 2017-03-10 10:37:21, Steve Longerbeam wrote:
>> Hi Hans,
>>
>> On 03/10/2017 04:03 AM, Hans Verkuil wrote:
>>> On 10/03/17 05:52, Steve Longerbeam wrote:
>>>> Add a new FRAME_INTERVAL_ERROR event to signal that a video capture or
>>>> output device has measured an interval between the reception or transmit
>>>> completion of two consecutive frames of video that is outside the nominal
>>>> frame interval by some tolerance value.
>>>
>>> Reading back what was said on this I agree with Sakari that this doesn't
>>> belong here.
>>>
>>> Userspace can detect this just as easily (if not easier) with a timeout.
>>>
>>
>>
>> Unfortunately measuring frame intervals from userland is not accurate
>> enough for i.MX6.
>>
>> The issue here is that the IPUv3, specifically the CSI unit, can
>> permanently lose vertical sync if there are truncated frames sent
>> on the bt.656 bus. We have seen a single missing line of video cause
>> loss of vertical sync. The only way to correct this is to shutdown
>> the IPU capture hardware and restart, which can be accomplished
>> simply by restarting streaming from userland.
>>
>> There are no other indicators from the sensor about these short
>> frame events (believe me, we've exhausted all avenues with the ADV718x).
>> And the IPUv3 DMA engine has no status indicators for short frames
>> either. So the only way to detect them is by measuring frame intervals.
>>
>> The intervals have to be able to resolve a single line of missing video.
>> With a PAL video source that requires better than 58 usec accuracy.
>>
>> There is too much uncertainty to resolve this at user level. The
>> driver is able to resolve this by measuring intervals between hardware
>> interrupts as long as interrupt latency is reasonably low, and we
>> have another method using the i.MX6 hardware input capture support
>> that can measure these intervals very accurately with no errors
>> introduced by interrupt latency.
>
> Requiring < 58 usec interrupt latency for correct operation is a
> little too optimistic, no?


No it's not too optimistic, from experience the imx6 kernel has irq
latency less than 10 usec under normal system load. False events can be
generated if the latency gets bad, it's true, and that's why there is
the imx6 timer input capture approach.

Steve

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Hans Verkuil]

On 10/03/17 19:37, Steve Longerbeam wrote:
> Hi Hans,
> 
> On 03/10/2017 04:03 AM, Hans Verkuil wrote:
>> On 10/03/17 05:52, Steve Longerbeam wrote:
>>> Add a new FRAME_INTERVAL_ERROR event to signal that a video capture or
>>> output device has measured an interval between the reception or transmit
>>> completion of two consecutive frames of video that is outside the nominal
>>> frame interval by some tolerance value.
>>
>> Reading back what was said on this I agree with Sakari that this doesn't
>> belong here.
>>
>> Userspace can detect this just as easily (if not easier) with a timeout.
>>
> 
> 
> Unfortunately measuring frame intervals from userland is not accurate
> enough for i.MX6.
> 
> The issue here is that the IPUv3, specifically the CSI unit, can
> permanently lose vertical sync if there are truncated frames sent
> on the bt.656 bus. We have seen a single missing line of video cause
> loss of vertical sync. The only way to correct this is to shutdown
> the IPU capture hardware and restart, which can be accomplished
> simply by restarting streaming from userland.
> 
> There are no other indicators from the sensor about these short
> frame events (believe me, we've exhausted all avenues with the ADV718x).
> And the IPUv3 DMA engine has no status indicators for short frames
> either. So the only way to detect them is by measuring frame intervals.
> 
> The intervals have to be able to resolve a single line of missing video.
> With a PAL video source that requires better than 58 usec accuracy.
> 
> There is too much uncertainty to resolve this at user level. The
> driver is able to resolve this by measuring intervals between hardware
> interrupts as long as interrupt latency is reasonably low, and we
> have another method using the i.MX6 hardware input capture support
> that can measure these intervals very accurately with no errors
> introduced by interrupt latency.
> 
> I made this event a private event to imx-media driver in a previous
> iteration, so I can return it to a private event, but this can't be
> done at user level.

It's fine to use an internal event as long as the end-user doesn't
see it. But if you lose vsyncs, then you never capture another frame,
right? So userspace can detect that (i.e. no new frames arrive) and
it can timeout on that. Or you detect it in the driver and restart there,
or call vb2_queue_error().

Anything really as long as this event isn't user-visible :-)

Regards,

	Hans

> 
> Steve
> 
> 
>>
>>>
>>> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
>>> ---
>>>  Documentation/media/uapi/v4l/vidioc-dqevent.rst | 6 ++++++
>>>  Documentation/media/videodev2.h.rst.exceptions  | 1 +
>>>  include/uapi/linux/videodev2.h                  | 1 +
>>>  3 files changed, 8 insertions(+)
>>>
>>> diff --git a/Documentation/media/uapi/v4l/vidioc-dqevent.rst b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
>>> index 8d663a7..dc77363 100644
>>> --- a/Documentation/media/uapi/v4l/vidioc-dqevent.rst
>>> +++ b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
>>> @@ -197,6 +197,12 @@ call.
>>>      the regions changes. This event has a struct
>>>      :c:type:`v4l2_event_motion_det`
>>>      associated with it.
>>> +    * - ``V4L2_EVENT_FRAME_INTERVAL_ERROR``
>>> +      - 7
>>> +      - This event is triggered when the video capture or output device
>>> +    has measured an interval between the reception or transmit
>>> +    completion of two consecutive frames of video that is outside
>>> +    the nominal frame interval by some tolerance value.
>>>      * - ``V4L2_EVENT_PRIVATE_START``
>>>        - 0x08000000
>>>        - Base event number for driver-private events.
>>> diff --git a/Documentation/media/videodev2.h.rst.exceptions b/Documentation/media/videodev2.h.rst.exceptions
>>> index e11a0d0..c7d8fad 100644
>>> --- a/Documentation/media/videodev2.h.rst.exceptions
>>> +++ b/Documentation/media/videodev2.h.rst.exceptions
>>> @@ -459,6 +459,7 @@ replace define V4L2_EVENT_CTRL event-type
>>>  replace define V4L2_EVENT_FRAME_SYNC event-type
>>>  replace define V4L2_EVENT_SOURCE_CHANGE event-type
>>>  replace define V4L2_EVENT_MOTION_DET event-type
>>> +replace define V4L2_EVENT_FRAME_INTERVAL_ERROR event-type
>>>  replace define V4L2_EVENT_PRIVATE_START event-type
>>>
>>>  replace define V4L2_EVENT_CTRL_CH_VALUE ctrl-changes-flags
>>> diff --git a/include/uapi/linux/videodev2.h b/include/uapi/linux/videodev2.h
>>> index 45184a2..cf5a0d0 100644
>>> --- a/include/uapi/linux/videodev2.h
>>> +++ b/include/uapi/linux/videodev2.h
>>> @@ -2131,6 +2131,7 @@ struct v4l2_streamparm {
>>>  #define V4L2_EVENT_FRAME_SYNC            4
>>>  #define V4L2_EVENT_SOURCE_CHANGE        5
>>>  #define V4L2_EVENT_MOTION_DET            6
>>> +#define V4L2_EVENT_FRAME_INTERVAL_ERROR        7
>>>  #define V4L2_EVENT_PRIVATE_START        0x08000000
>>>
>>>  /* Payload for V4L2_EVENT_VSYNC */
>>>
>>
> 

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Hans Verkuil]

On 10/03/17 19:37, Steve Longerbeam wrote:
> Hi Hans,
> 
> On 03/10/2017 04:03 AM, Hans Verkuil wrote:
>> On 10/03/17 05:52, Steve Longerbeam wrote:
>>> Add a new FRAME_INTERVAL_ERROR event to signal that a video capture or
>>> output device has measured an interval between the reception or transmit
>>> completion of two consecutive frames of video that is outside the nominal
>>> frame interval by some tolerance value.
>>
>> Reading back what was said on this I agree with Sakari that this doesn't
>> belong here.
>>
>> Userspace can detect this just as easily (if not easier) with a timeout.
>>
> 
> 
> Unfortunately measuring frame intervals from userland is not accurate
> enough for i.MX6.
> 
> The issue here is that the IPUv3, specifically the CSI unit, can
> permanently lose vertical sync if there are truncated frames sent
> on the bt.656 bus. We have seen a single missing line of video cause
> loss of vertical sync. The only way to correct this is to shutdown
> the IPU capture hardware and restart, which can be accomplished
> simply by restarting streaming from userland.
> 
> There are no other indicators from the sensor about these short
> frame events (believe me, we've exhausted all avenues with the ADV718x).
> And the IPUv3 DMA engine has no status indicators for short frames
> either. So the only way to detect them is by measuring frame intervals.
> 
> The intervals have to be able to resolve a single line of missing video.
> With a PAL video source that requires better than 58 usec accuracy.
> 
> There is too much uncertainty to resolve this at user level. The
> driver is able to resolve this by measuring intervals between hardware
> interrupts as long as interrupt latency is reasonably low, and we
> have another method using the i.MX6 hardware input capture support
> that can measure these intervals very accurately with no errors
> introduced by interrupt latency.
> 
> I made this event a private event to imx-media driver in a previous
> iteration, so I can return it to a private event, but this can't be
> done at user level.

It's fine to use an internal event as long as the end-user doesn't
see it. But if you lose vsyncs, then you never capture another frame,
right? So userspace can detect that (i.e. no new frames arrive) and
it can timeout on that. Or you detect it in the driver and restart there,
or call vb2_queue_error().

Anything really as long as this event isn't user-visible :-)

Regards,

	Hans

> 
> Steve
> 
> 
>>
>>>
>>> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
>>> ---
>>>  Documentation/media/uapi/v4l/vidioc-dqevent.rst | 6 ++++++
>>>  Documentation/media/videodev2.h.rst.exceptions  | 1 +
>>>  include/uapi/linux/videodev2.h                  | 1 +
>>>  3 files changed, 8 insertions(+)
>>>
>>> diff --git a/Documentation/media/uapi/v4l/vidioc-dqevent.rst b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
>>> index 8d663a7..dc77363 100644
>>> --- a/Documentation/media/uapi/v4l/vidioc-dqevent.rst
>>> +++ b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
>>> @@ -197,6 +197,12 @@ call.
>>>      the regions changes. This event has a struct
>>>      :c:type:`v4l2_event_motion_det`
>>>      associated with it.
>>> +    * - ``V4L2_EVENT_FRAME_INTERVAL_ERROR``
>>> +      - 7
>>> +      - This event is triggered when the video capture or output device
>>> +    has measured an interval between the reception or transmit
>>> +    completion of two consecutive frames of video that is outside
>>> +    the nominal frame interval by some tolerance value.
>>>      * - ``V4L2_EVENT_PRIVATE_START``
>>>        - 0x08000000
>>>        - Base event number for driver-private events.
>>> diff --git a/Documentation/media/videodev2.h.rst.exceptions b/Documentation/media/videodev2.h.rst.exceptions
>>> index e11a0d0..c7d8fad 100644
>>> --- a/Documentation/media/videodev2.h.rst.exceptions
>>> +++ b/Documentation/media/videodev2.h.rst.exceptions
>>> @@ -459,6 +459,7 @@ replace define V4L2_EVENT_CTRL event-type
>>>  replace define V4L2_EVENT_FRAME_SYNC event-type
>>>  replace define V4L2_EVENT_SOURCE_CHANGE event-type
>>>  replace define V4L2_EVENT_MOTION_DET event-type
>>> +replace define V4L2_EVENT_FRAME_INTERVAL_ERROR event-type
>>>  replace define V4L2_EVENT_PRIVATE_START event-type
>>>
>>>  replace define V4L2_EVENT_CTRL_CH_VALUE ctrl-changes-flags
>>> diff --git a/include/uapi/linux/videodev2.h b/include/uapi/linux/videodev2.h
>>> index 45184a2..cf5a0d0 100644
>>> --- a/include/uapi/linux/videodev2.h
>>> +++ b/include/uapi/linux/videodev2.h
>>> @@ -2131,6 +2131,7 @@ struct v4l2_streamparm {
>>>  #define V4L2_EVENT_FRAME_SYNC            4
>>>  #define V4L2_EVENT_SOURCE_CHANGE        5
>>>  #define V4L2_EVENT_MOTION_DET            6
>>> +#define V4L2_EVENT_FRAME_INTERVAL_ERROR        7
>>>  #define V4L2_EVENT_PRIVATE_START        0x08000000
>>>
>>>  /* Payload for V4L2_EVENT_VSYNC */
>>>
>>
> 

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Hans Verkuil]

On 10/03/17 19:37, Steve Longerbeam wrote:
> Hi Hans,
> 
> On 03/10/2017 04:03 AM, Hans Verkuil wrote:
>> On 10/03/17 05:52, Steve Longerbeam wrote:
>>> Add a new FRAME_INTERVAL_ERROR event to signal that a video capture or
>>> output device has measured an interval between the reception or transmit
>>> completion of two consecutive frames of video that is outside the nominal
>>> frame interval by some tolerance value.
>>
>> Reading back what was said on this I agree with Sakari that this doesn't
>> belong here.
>>
>> Userspace can detect this just as easily (if not easier) with a timeout.
>>
> 
> 
> Unfortunately measuring frame intervals from userland is not accurate
> enough for i.MX6.
> 
> The issue here is that the IPUv3, specifically the CSI unit, can
> permanently lose vertical sync if there are truncated frames sent
> on the bt.656 bus. We have seen a single missing line of video cause
> loss of vertical sync. The only way to correct this is to shutdown
> the IPU capture hardware and restart, which can be accomplished
> simply by restarting streaming from userland.
> 
> There are no other indicators from the sensor about these short
> frame events (believe me, we've exhausted all avenues with the ADV718x).
> And the IPUv3 DMA engine has no status indicators for short frames
> either. So the only way to detect them is by measuring frame intervals.
> 
> The intervals have to be able to resolve a single line of missing video.
> With a PAL video source that requires better than 58 usec accuracy.
> 
> There is too much uncertainty to resolve this at user level. The
> driver is able to resolve this by measuring intervals between hardware
> interrupts as long as interrupt latency is reasonably low, and we
> have another method using the i.MX6 hardware input capture support
> that can measure these intervals very accurately with no errors
> introduced by interrupt latency.
> 
> I made this event a private event to imx-media driver in a previous
> iteration, so I can return it to a private event, but this can't be
> done at user level.

It's fine to use an internal event as long as the end-user doesn't
see it. But if you lose vsyncs, then you never capture another frame,
right? So userspace can detect that (i.e. no new frames arrive) and
it can timeout on that. Or you detect it in the driver and restart there,
or call vb2_queue_error().

Anything really as long as this event isn't user-visible :-)

Regards,

	Hans

> 
> Steve
> 
> 
>>
>>>
>>> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
>>> ---
>>>  Documentation/media/uapi/v4l/vidioc-dqevent.rst | 6 ++++++
>>>  Documentation/media/videodev2.h.rst.exceptions  | 1 +
>>>  include/uapi/linux/videodev2.h                  | 1 +
>>>  3 files changed, 8 insertions(+)
>>>
>>> diff --git a/Documentation/media/uapi/v4l/vidioc-dqevent.rst b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
>>> index 8d663a7..dc77363 100644
>>> --- a/Documentation/media/uapi/v4l/vidioc-dqevent.rst
>>> +++ b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
>>> @@ -197,6 +197,12 @@ call.
>>>      the regions changes. This event has a struct
>>>      :c:type:`v4l2_event_motion_det`
>>>      associated with it.
>>> +    * - ``V4L2_EVENT_FRAME_INTERVAL_ERROR``
>>> +      - 7
>>> +      - This event is triggered when the video capture or output device
>>> +    has measured an interval between the reception or transmit
>>> +    completion of two consecutive frames of video that is outside
>>> +    the nominal frame interval by some tolerance value.
>>>      * - ``V4L2_EVENT_PRIVATE_START``
>>>        - 0x08000000
>>>        - Base event number for driver-private events.
>>> diff --git a/Documentation/media/videodev2.h.rst.exceptions b/Documentation/media/videodev2.h.rst.exceptions
>>> index e11a0d0..c7d8fad 100644
>>> --- a/Documentation/media/videodev2.h.rst.exceptions
>>> +++ b/Documentation/media/videodev2.h.rst.exceptions
>>> @@ -459,6 +459,7 @@ replace define V4L2_EVENT_CTRL event-type
>>>  replace define V4L2_EVENT_FRAME_SYNC event-type
>>>  replace define V4L2_EVENT_SOURCE_CHANGE event-type
>>>  replace define V4L2_EVENT_MOTION_DET event-type
>>> +replace define V4L2_EVENT_FRAME_INTERVAL_ERROR event-type
>>>  replace define V4L2_EVENT_PRIVATE_START event-type
>>>
>>>  replace define V4L2_EVENT_CTRL_CH_VALUE ctrl-changes-flags
>>> diff --git a/include/uapi/linux/videodev2.h b/include/uapi/linux/videodev2.h
>>> index 45184a2..cf5a0d0 100644
>>> --- a/include/uapi/linux/videodev2.h
>>> +++ b/include/uapi/linux/videodev2.h
>>> @@ -2131,6 +2131,7 @@ struct v4l2_streamparm {
>>>  #define V4L2_EVENT_FRAME_SYNC            4
>>>  #define V4L2_EVENT_SOURCE_CHANGE        5
>>>  #define V4L2_EVENT_MOTION_DET            6
>>> +#define V4L2_EVENT_FRAME_INTERVAL_ERROR        7
>>>  #define V4L2_EVENT_PRIVATE_START        0x08000000
>>>
>>>  /* Payload for V4L2_EVENT_VSYNC */
>>>
>>
> 

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/11/2017 03:39 AM, Hans Verkuil wrote:
> On 10/03/17 19:37, Steve Longerbeam wrote:
>> Hi Hans,
>>
>> On 03/10/2017 04:03 AM, Hans Verkuil wrote:
>>> On 10/03/17 05:52, Steve Longerbeam wrote:
>>>> Add a new FRAME_INTERVAL_ERROR event to signal that a video capture or
>>>> output device has measured an interval between the reception or transmit
>>>> completion of two consecutive frames of video that is outside the nominal
>>>> frame interval by some tolerance value.
>>>
>>> Reading back what was said on this I agree with Sakari that this doesn't
>>> belong here.
>>>
>>> Userspace can detect this just as easily (if not easier) with a timeout.
>>>
>>
>>
>> Unfortunately measuring frame intervals from userland is not accurate
>> enough for i.MX6.
>>
>> The issue here is that the IPUv3, specifically the CSI unit, can
>> permanently lose vertical sync if there are truncated frames sent
>> on the bt.656 bus. We have seen a single missing line of video cause
>> loss of vertical sync. The only way to correct this is to shutdown
>> the IPU capture hardware and restart, which can be accomplished
>> simply by restarting streaming from userland.
>>
>> There are no other indicators from the sensor about these short
>> frame events (believe me, we've exhausted all avenues with the ADV718x).
>> And the IPUv3 DMA engine has no status indicators for short frames
>> either. So the only way to detect them is by measuring frame intervals.
>>
>> The intervals have to be able to resolve a single line of missing video.
>> With a PAL video source that requires better than 58 usec accuracy.
>>
>> There is too much uncertainty to resolve this at user level. The
>> driver is able to resolve this by measuring intervals between hardware
>> interrupts as long as interrupt latency is reasonably low, and we
>> have another method using the i.MX6 hardware input capture support
>> that can measure these intervals very accurately with no errors
>> introduced by interrupt latency.
>>
>> I made this event a private event to imx-media driver in a previous
>> iteration, so I can return it to a private event, but this can't be
>> done at user level.
>
> It's fine to use an internal event as long as the end-user doesn't
> see it. But if you lose vsyncs, then you never capture another frame,
> right?

No, that's not correct. By loss of vertical sync, I mean the IPU
captures portions of two different frames, resulting in a permanent
"split image", with one frame containing portions of two consecutive
images. Or, the video rolls continuously, if you remember the old CRT
television sets of yore, it's the same rolling effect.


> So userspace can detect that (i.e. no new frames arrive) and
> it can timeout on that. Or you detect it in the driver and restart there,
> or call vb2_queue_error().
>

There is no timeout, the frames keep coming, but they are split images
or rolling.

> Anything really as long as this event isn't user-visible :-)

The event must be user visible, otherwise the user has no indication
the error, and can't correct it by stream restart.

Steve

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/11/2017 03:39 AM, Hans Verkuil wrote:
> On 10/03/17 19:37, Steve Longerbeam wrote:
>> Hi Hans,
>>
>> On 03/10/2017 04:03 AM, Hans Verkuil wrote:
>>> On 10/03/17 05:52, Steve Longerbeam wrote:
>>>> Add a new FRAME_INTERVAL_ERROR event to signal that a video capture or
>>>> output device has measured an interval between the reception or transmit
>>>> completion of two consecutive frames of video that is outside the nominal
>>>> frame interval by some tolerance value.
>>>
>>> Reading back what was said on this I agree with Sakari that this doesn't
>>> belong here.
>>>
>>> Userspace can detect this just as easily (if not easier) with a timeout.
>>>
>>
>>
>> Unfortunately measuring frame intervals from userland is not accurate
>> enough for i.MX6.
>>
>> The issue here is that the IPUv3, specifically the CSI unit, can
>> permanently lose vertical sync if there are truncated frames sent
>> on the bt.656 bus. We have seen a single missing line of video cause
>> loss of vertical sync. The only way to correct this is to shutdown
>> the IPU capture hardware and restart, which can be accomplished
>> simply by restarting streaming from userland.
>>
>> There are no other indicators from the sensor about these short
>> frame events (believe me, we've exhausted all avenues with the ADV718x).
>> And the IPUv3 DMA engine has no status indicators for short frames
>> either. So the only way to detect them is by measuring frame intervals.
>>
>> The intervals have to be able to resolve a single line of missing video.
>> With a PAL video source that requires better than 58 usec accuracy.
>>
>> There is too much uncertainty to resolve this at user level. The
>> driver is able to resolve this by measuring intervals between hardware
>> interrupts as long as interrupt latency is reasonably low, and we
>> have another method using the i.MX6 hardware input capture support
>> that can measure these intervals very accurately with no errors
>> introduced by interrupt latency.
>>
>> I made this event a private event to imx-media driver in a previous
>> iteration, so I can return it to a private event, but this can't be
>> done at user level.
>
> It's fine to use an internal event as long as the end-user doesn't
> see it. But if you lose vsyncs, then you never capture another frame,
> right?

No, that's not correct. By loss of vertical sync, I mean the IPU
captures portions of two different frames, resulting in a permanent
"split image", with one frame containing portions of two consecutive
images. Or, the video rolls continuously, if you remember the old CRT
television sets of yore, it's the same rolling effect.


> So userspace can detect that (i.e. no new frames arrive) and
> it can timeout on that. Or you detect it in the driver and restart there,
> or call vb2_queue_error().
>

There is no timeout, the frames keep coming, but they are split images
or rolling.

> Anything really as long as this event isn't user-visible :-)

The event must be user visible, otherwise the user has no indication
the error, and can't correct it by stream restart.

Steve

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/11/2017 03:39 AM, Hans Verkuil wrote:
> On 10/03/17 19:37, Steve Longerbeam wrote:
>> Hi Hans,
>>
>> On 03/10/2017 04:03 AM, Hans Verkuil wrote:
>>> On 10/03/17 05:52, Steve Longerbeam wrote:
>>>> Add a new FRAME_INTERVAL_ERROR event to signal that a video capture or
>>>> output device has measured an interval between the reception or transmit
>>>> completion of two consecutive frames of video that is outside the nominal
>>>> frame interval by some tolerance value.
>>>
>>> Reading back what was said on this I agree with Sakari that this doesn't
>>> belong here.
>>>
>>> Userspace can detect this just as easily (if not easier) with a timeout.
>>>
>>
>>
>> Unfortunately measuring frame intervals from userland is not accurate
>> enough for i.MX6.
>>
>> The issue here is that the IPUv3, specifically the CSI unit, can
>> permanently lose vertical sync if there are truncated frames sent
>> on the bt.656 bus. We have seen a single missing line of video cause
>> loss of vertical sync. The only way to correct this is to shutdown
>> the IPU capture hardware and restart, which can be accomplished
>> simply by restarting streaming from userland.
>>
>> There are no other indicators from the sensor about these short
>> frame events (believe me, we've exhausted all avenues with the ADV718x).
>> And the IPUv3 DMA engine has no status indicators for short frames
>> either. So the only way to detect them is by measuring frame intervals.
>>
>> The intervals have to be able to resolve a single line of missing video.
>> With a PAL video source that requires better than 58 usec accuracy.
>>
>> There is too much uncertainty to resolve this at user level. The
>> driver is able to resolve this by measuring intervals between hardware
>> interrupts as long as interrupt latency is reasonably low, and we
>> have another method using the i.MX6 hardware input capture support
>> that can measure these intervals very accurately with no errors
>> introduced by interrupt latency.
>>
>> I made this event a private event to imx-media driver in a previous
>> iteration, so I can return it to a private event, but this can't be
>> done at user level.
>
> It's fine to use an internal event as long as the end-user doesn't
> see it. But if you lose vsyncs, then you never capture another frame,
> right?

No, that's not correct. By loss of vertical sync, I mean the IPU
captures portions of two different frames, resulting in a permanent
"split image", with one frame containing portions of two consecutive
images. Or, the video rolls continuously, if you remember the old CRT
television sets of yore, it's the same rolling effect.


> So userspace can detect that (i.e. no new frames arrive) and
> it can timeout on that. Or you detect it in the driver and restart there,
> or call vb2_queue_error().
>

There is no timeout, the frames keep coming, but they are split images
or rolling.

> Anything really as long as this event isn't user-visible :-)

The event must be user visible, otherwise the user has no indication
the error, and can't correct it by stream restart.

Steve

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Russell King - ARM Linux]

On Sat, Mar 11, 2017 at 10:14:49AM -0800, Steve Longerbeam wrote:
> On 03/11/2017 03:39 AM, Hans Verkuil wrote:
> >It's fine to use an internal event as long as the end-user doesn't
> >see it. But if you lose vsyncs, then you never capture another frame,
> >right?
> 
> No, that's not correct. By loss of vertical sync, I mean the IPU
> captures portions of two different frames, resulting in a permanent
> "split image", with one frame containing portions of two consecutive
> images. Or, the video rolls continuously, if you remember the old CRT
> television sets of yore, it's the same rolling effect.

I have seen that rolling effect, but the iMX6 regains correct sync
within one complete "roll" just fine here with IMX219.  However, it
has always recovered.

So, I don't think there's a problem with the iMX6 part of the
processing, and so I don't think we should cripple the iMX6 capture
drivers for this problem.

It seems to me that the problem is with the source.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Russell King - ARM Linux]

On Sat, Mar 11, 2017 at 10:14:49AM -0800, Steve Longerbeam wrote:
> On 03/11/2017 03:39 AM, Hans Verkuil wrote:
> >It's fine to use an internal event as long as the end-user doesn't
> >see it. But if you lose vsyncs, then you never capture another frame,
> >right?
> 
> No, that's not correct. By loss of vertical sync, I mean the IPU
> captures portions of two different frames, resulting in a permanent
> "split image", with one frame containing portions of two consecutive
> images. Or, the video rolls continuously, if you remember the old CRT
> television sets of yore, it's the same rolling effect.

I have seen that rolling effect, but the iMX6 regains correct sync
within one complete "roll" just fine here with IMX219.  However, it
has always recovered.

So, I don't think there's a problem with the iMX6 part of the
processing, and so I don't think we should cripple the iMX6 capture
drivers for this problem.

It seems to me that the problem is with the source.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Russell King - ARM Linux]

On Sat, Mar 11, 2017 at 10:14:49AM -0800, Steve Longerbeam wrote:
> On 03/11/2017 03:39 AM, Hans Verkuil wrote:
> >It's fine to use an internal event as long as the end-user doesn't
> >see it. But if you lose vsyncs, then you never capture another frame,
> >right?
> 
> No, that's not correct. By loss of vertical sync, I mean the IPU
> captures portions of two different frames, resulting in a permanent
> "split image", with one frame containing portions of two consecutive
> images. Or, the video rolls continuously, if you remember the old CRT
> television sets of yore, it's the same rolling effect.

I have seen that rolling effect, but the iMX6 regains correct sync
within one complete "roll" just fine here with IMX219.  However, it
has always recovered.

So, I don't think there's a problem with the iMX6 part of the
processing, and so I don't think we should cripple the iMX6 capture
drivers for this problem.

It seems to me that the problem is with the source.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/11/2017 10:51 AM, Russell King - ARM Linux wrote:
> On Sat, Mar 11, 2017 at 10:14:49AM -0800, Steve Longerbeam wrote:
>> On 03/11/2017 03:39 AM, Hans Verkuil wrote:
>>> It's fine to use an internal event as long as the end-user doesn't
>>> see it. But if you lose vsyncs, then you never capture another frame,
>>> right?
>>
>> No, that's not correct. By loss of vertical sync, I mean the IPU
>> captures portions of two different frames, resulting in a permanent
>> "split image", with one frame containing portions of two consecutive
>> images. Or, the video rolls continuously, if you remember the old CRT
>> television sets of yore, it's the same rolling effect.
>
> I have seen that rolling effect, but the iMX6 regains correct sync
> within one complete "roll" just fine here with IMX219.  However, it
> has always recovered.

I've seen permanent split images, and rolling that continues for
minutes.


>
> So, I don't think there's a problem with the iMX6 part of the
> processing, and so I don't think we should cripple the iMX6 capture
> drivers for this problem.
>
> It seems to me that the problem is with the source.

The the problem is almost surely in the CSI. It's handling of the
bt.656 sync codes is broken in some way.

Steve

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/11/2017 10:51 AM, Russell King - ARM Linux wrote:
> On Sat, Mar 11, 2017 at 10:14:49AM -0800, Steve Longerbeam wrote:
>> On 03/11/2017 03:39 AM, Hans Verkuil wrote:
>>> It's fine to use an internal event as long as the end-user doesn't
>>> see it. But if you lose vsyncs, then you never capture another frame,
>>> right?
>>
>> No, that's not correct. By loss of vertical sync, I mean the IPU
>> captures portions of two different frames, resulting in a permanent
>> "split image", with one frame containing portions of two consecutive
>> images. Or, the video rolls continuously, if you remember the old CRT
>> television sets of yore, it's the same rolling effect.
>
> I have seen that rolling effect, but the iMX6 regains correct sync
> within one complete "roll" just fine here with IMX219.  However, it
> has always recovered.

I've seen permanent split images, and rolling that continues for
minutes.


>
> So, I don't think there's a problem with the iMX6 part of the
> processing, and so I don't think we should cripple the iMX6 capture
> drivers for this problem.
>
> It seems to me that the problem is with the source.

The the problem is almost surely in the CSI. It's handling of the
bt.656 sync codes is broken in some way.

Steve

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/11/2017 10:51 AM, Russell King - ARM Linux wrote:
> On Sat, Mar 11, 2017 at 10:14:49AM -0800, Steve Longerbeam wrote:
>> On 03/11/2017 03:39 AM, Hans Verkuil wrote:
>>> It's fine to use an internal event as long as the end-user doesn't
>>> see it. But if you lose vsyncs, then you never capture another frame,
>>> right?
>>
>> No, that's not correct. By loss of vertical sync, I mean the IPU
>> captures portions of two different frames, resulting in a permanent
>> "split image", with one frame containing portions of two consecutive
>> images. Or, the video rolls continuously, if you remember the old CRT
>> television sets of yore, it's the same rolling effect.
>
> I have seen that rolling effect, but the iMX6 regains correct sync
> within one complete "roll" just fine here with IMX219.  However, it
> has always recovered.

I've seen permanent split images, and rolling that continues for
minutes.


>
> So, I don't think there's a problem with the iMX6 part of the
> processing, and so I don't think we should cripple the iMX6 capture
> drivers for this problem.
>
> It seems to me that the problem is with the source.

The the problem is almost surely in the CSI. It's handling of the
bt.656 sync codes is broken in some way.

Steve

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/11/2017 10:51 AM, Russell King - ARM Linux wrote:
> On Sat, Mar 11, 2017 at 10:14:49AM -0800, Steve Longerbeam wrote:
>> On 03/11/2017 03:39 AM, Hans Verkuil wrote:
>>> It's fine to use an internal event as long as the end-user doesn't
>>> see it. But if you lose vsyncs, then you never capture another frame,
>>> right?
>>
>> No, that's not correct. By loss of vertical sync, I mean the IPU
>> captures portions of two different frames, resulting in a permanent
>> "split image", with one frame containing portions of two consecutive
>> images. Or, the video rolls continuously, if you remember the old CRT
>> television sets of yore, it's the same rolling effect.
>
> I have seen that rolling effect, but the iMX6 regains correct sync
> within one complete "roll" just fine here with IMX219.  However, it
> has always recovered.
>
> So, I don't think there's a problem with the iMX6 part of the
> processing, and so I don't think we should cripple the iMX6 capture
> drivers for this problem.

And there is no crippling going on. Measuring the frame intervals
adds very little overhead.

Steve

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/11/2017 10:51 AM, Russell King - ARM Linux wrote:
> On Sat, Mar 11, 2017 at 10:14:49AM -0800, Steve Longerbeam wrote:
>> On 03/11/2017 03:39 AM, Hans Verkuil wrote:
>>> It's fine to use an internal event as long as the end-user doesn't
>>> see it. But if you lose vsyncs, then you never capture another frame,
>>> right?
>>
>> No, that's not correct. By loss of vertical sync, I mean the IPU
>> captures portions of two different frames, resulting in a permanent
>> "split image", with one frame containing portions of two consecutive
>> images. Or, the video rolls continuously, if you remember the old CRT
>> television sets of yore, it's the same rolling effect.
>
> I have seen that rolling effect, but the iMX6 regains correct sync
> within one complete "roll" just fine here with IMX219.  However, it
> has always recovered.
>
> So, I don't think there's a problem with the iMX6 part of the
> processing, and so I don't think we should cripple the iMX6 capture
> drivers for this problem.

And there is no crippling going on. Measuring the frame intervals
adds very little overhead.

Steve

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/11/2017 10:51 AM, Russell King - ARM Linux wrote:
> On Sat, Mar 11, 2017 at 10:14:49AM -0800, Steve Longerbeam wrote:
>> On 03/11/2017 03:39 AM, Hans Verkuil wrote:
>>> It's fine to use an internal event as long as the end-user doesn't
>>> see it. But if you lose vsyncs, then you never capture another frame,
>>> right?
>>
>> No, that's not correct. By loss of vertical sync, I mean the IPU
>> captures portions of two different frames, resulting in a permanent
>> "split image", with one frame containing portions of two consecutive
>> images. Or, the video rolls continuously, if you remember the old CRT
>> television sets of yore, it's the same rolling effect.
>
> I have seen that rolling effect, but the iMX6 regains correct sync
> within one complete "roll" just fine here with IMX219.  However, it
> has always recovered.
>
> So, I don't think there's a problem with the iMX6 part of the
> processing, and so I don't think we should cripple the iMX6 capture
> drivers for this problem.

And there is no crippling going on. Measuring the frame intervals
adds very little overhead.

Steve

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Hans Verkuil]

On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
> 
> 
> On 03/11/2017 03:39 AM, Hans Verkuil wrote:
>> On 10/03/17 19:37, Steve Longerbeam wrote:
>>> Hi Hans,
>>>
>>> On 03/10/2017 04:03 AM, Hans Verkuil wrote:
>>>> On 10/03/17 05:52, Steve Longerbeam wrote:
>>>>> Add a new FRAME_INTERVAL_ERROR event to signal that a video capture or
>>>>> output device has measured an interval between the reception or transmit
>>>>> completion of two consecutive frames of video that is outside the nominal
>>>>> frame interval by some tolerance value.
>>>>
>>>> Reading back what was said on this I agree with Sakari that this doesn't
>>>> belong here.
>>>>
>>>> Userspace can detect this just as easily (if not easier) with a timeout.
>>>>
>>>
>>>
>>> Unfortunately measuring frame intervals from userland is not accurate
>>> enough for i.MX6.
>>>
>>> The issue here is that the IPUv3, specifically the CSI unit, can
>>> permanently lose vertical sync if there are truncated frames sent
>>> on the bt.656 bus. We have seen a single missing line of video cause
>>> loss of vertical sync. The only way to correct this is to shutdown
>>> the IPU capture hardware and restart, which can be accomplished
>>> simply by restarting streaming from userland.
>>>
>>> There are no other indicators from the sensor about these short
>>> frame events (believe me, we've exhausted all avenues with the ADV718x).
>>> And the IPUv3 DMA engine has no status indicators for short frames
>>> either. So the only way to detect them is by measuring frame intervals.
>>>
>>> The intervals have to be able to resolve a single line of missing video.
>>> With a PAL video source that requires better than 58 usec accuracy.
>>>
>>> There is too much uncertainty to resolve this at user level. The
>>> driver is able to resolve this by measuring intervals between hardware
>>> interrupts as long as interrupt latency is reasonably low, and we
>>> have another method using the i.MX6 hardware input capture support
>>> that can measure these intervals very accurately with no errors
>>> introduced by interrupt latency.
>>>
>>> I made this event a private event to imx-media driver in a previous
>>> iteration, so I can return it to a private event, but this can't be
>>> done at user level.
>>
>> It's fine to use an internal event as long as the end-user doesn't
>> see it. But if you lose vsyncs, then you never capture another frame,
>> right?
> 
> No, that's not correct. By loss of vertical sync, I mean the IPU
> captures portions of two different frames, resulting in a permanent
> "split image", with one frame containing portions of two consecutive
> images. Or, the video rolls continuously, if you remember the old CRT
> television sets of yore, it's the same rolling effect.
> 
> 
>> So userspace can detect that (i.e. no new frames arrive) and
>> it can timeout on that. Or you detect it in the driver and restart there,
>> or call vb2_queue_error().
>>
> 
> There is no timeout, the frames keep coming, but they are split images
> or rolling.

Ah, OK. That wasn't clear to me from the description.

> 
>> Anything really as long as this event isn't user-visible :-)
> 
> The event must be user visible, otherwise the user has no indication
> the error, and can't correct it by stream restart.

In that case the driver can detect this and call vb2_queue_error. It's
what it is there for.

The event doesn't help you since only this driver has this issue. So nobody
will watch this event, unless it is sw specifically written for this SoC.

Much better to call vb2_queue_error to signal a fatal error (which this
apparently is) since there are more drivers that do this, and vivid supports
triggering this condition as well.

Regards,

	Hans

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Hans Verkuil]

On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
> 
> 
> On 03/11/2017 03:39 AM, Hans Verkuil wrote:
>> On 10/03/17 19:37, Steve Longerbeam wrote:
>>> Hi Hans,
>>>
>>> On 03/10/2017 04:03 AM, Hans Verkuil wrote:
>>>> On 10/03/17 05:52, Steve Longerbeam wrote:
>>>>> Add a new FRAME_INTERVAL_ERROR event to signal that a video capture or
>>>>> output device has measured an interval between the reception or transmit
>>>>> completion of two consecutive frames of video that is outside the nominal
>>>>> frame interval by some tolerance value.
>>>>
>>>> Reading back what was said on this I agree with Sakari that this doesn't
>>>> belong here.
>>>>
>>>> Userspace can detect this just as easily (if not easier) with a timeout.
>>>>
>>>
>>>
>>> Unfortunately measuring frame intervals from userland is not accurate
>>> enough for i.MX6.
>>>
>>> The issue here is that the IPUv3, specifically the CSI unit, can
>>> permanently lose vertical sync if there are truncated frames sent
>>> on the bt.656 bus. We have seen a single missing line of video cause
>>> loss of vertical sync. The only way to correct this is to shutdown
>>> the IPU capture hardware and restart, which can be accomplished
>>> simply by restarting streaming from userland.
>>>
>>> There are no other indicators from the sensor about these short
>>> frame events (believe me, we've exhausted all avenues with the ADV718x).
>>> And the IPUv3 DMA engine has no status indicators for short frames
>>> either. So the only way to detect them is by measuring frame intervals.
>>>
>>> The intervals have to be able to resolve a single line of missing video.
>>> With a PAL video source that requires better than 58 usec accuracy.
>>>
>>> There is too much uncertainty to resolve this at user level. The
>>> driver is able to resolve this by measuring intervals between hardware
>>> interrupts as long as interrupt latency is reasonably low, and we
>>> have another method using the i.MX6 hardware input capture support
>>> that can measure these intervals very accurately with no errors
>>> introduced by interrupt latency.
>>>
>>> I made this event a private event to imx-media driver in a previous
>>> iteration, so I can return it to a private event, but this can't be
>>> done at user level.
>>
>> It's fine to use an internal event as long as the end-user doesn't
>> see it. But if you lose vsyncs, then you never capture another frame,
>> right?
> 
> No, that's not correct. By loss of vertical sync, I mean the IPU
> captures portions of two different frames, resulting in a permanent
> "split image", with one frame containing portions of two consecutive
> images. Or, the video rolls continuously, if you remember the old CRT
> television sets of yore, it's the same rolling effect.
> 
> 
>> So userspace can detect that (i.e. no new frames arrive) and
>> it can timeout on that. Or you detect it in the driver and restart there,
>> or call vb2_queue_error().
>>
> 
> There is no timeout, the frames keep coming, but they are split images
> or rolling.

Ah, OK. That wasn't clear to me from the description.

> 
>> Anything really as long as this event isn't user-visible :-)
> 
> The event must be user visible, otherwise the user has no indication
> the error, and can't correct it by stream restart.

In that case the driver can detect this and call vb2_queue_error. It's
what it is there for.

The event doesn't help you since only this driver has this issue. So nobody
will watch this event, unless it is sw specifically written for this SoC.

Much better to call vb2_queue_error to signal a fatal error (which this
apparently is) since there are more drivers that do this, and vivid supports
triggering this condition as well.

Regards,

	Hans

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Hans Verkuil]

On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
> 
> 
> On 03/11/2017 03:39 AM, Hans Verkuil wrote:
>> On 10/03/17 19:37, Steve Longerbeam wrote:
>>> Hi Hans,
>>>
>>> On 03/10/2017 04:03 AM, Hans Verkuil wrote:
>>>> On 10/03/17 05:52, Steve Longerbeam wrote:
>>>>> Add a new FRAME_INTERVAL_ERROR event to signal that a video capture or
>>>>> output device has measured an interval between the reception or transmit
>>>>> completion of two consecutive frames of video that is outside the nominal
>>>>> frame interval by some tolerance value.
>>>>
>>>> Reading back what was said on this I agree with Sakari that this doesn't
>>>> belong here.
>>>>
>>>> Userspace can detect this just as easily (if not easier) with a timeout.
>>>>
>>>
>>>
>>> Unfortunately measuring frame intervals from userland is not accurate
>>> enough for i.MX6.
>>>
>>> The issue here is that the IPUv3, specifically the CSI unit, can
>>> permanently lose vertical sync if there are truncated frames sent
>>> on the bt.656 bus. We have seen a single missing line of video cause
>>> loss of vertical sync. The only way to correct this is to shutdown
>>> the IPU capture hardware and restart, which can be accomplished
>>> simply by restarting streaming from userland.
>>>
>>> There are no other indicators from the sensor about these short
>>> frame events (believe me, we've exhausted all avenues with the ADV718x).
>>> And the IPUv3 DMA engine has no status indicators for short frames
>>> either. So the only way to detect them is by measuring frame intervals.
>>>
>>> The intervals have to be able to resolve a single line of missing video.
>>> With a PAL video source that requires better than 58 usec accuracy.
>>>
>>> There is too much uncertainty to resolve this at user level. The
>>> driver is able to resolve this by measuring intervals between hardware
>>> interrupts as long as interrupt latency is reasonably low, and we
>>> have another method using the i.MX6 hardware input capture support
>>> that can measure these intervals very accurately with no errors
>>> introduced by interrupt latency.
>>>
>>> I made this event a private event to imx-media driver in a previous
>>> iteration, so I can return it to a private event, but this can't be
>>> done at user level.
>>
>> It's fine to use an internal event as long as the end-user doesn't
>> see it. But if you lose vsyncs, then you never capture another frame,
>> right?
> 
> No, that's not correct. By loss of vertical sync, I mean the IPU
> captures portions of two different frames, resulting in a permanent
> "split image", with one frame containing portions of two consecutive
> images. Or, the video rolls continuously, if you remember the old CRT
> television sets of yore, it's the same rolling effect.
> 
> 
>> So userspace can detect that (i.e. no new frames arrive) and
>> it can timeout on that. Or you detect it in the driver and restart there,
>> or call vb2_queue_error().
>>
> 
> There is no timeout, the frames keep coming, but they are split images
> or rolling.

Ah, OK. That wasn't clear to me from the description.

> 
>> Anything really as long as this event isn't user-visible :-)
> 
> The event must be user visible, otherwise the user has no indication
> the error, and can't correct it by stream restart.

In that case the driver can detect this and call vb2_queue_error. It's
what it is there for.

The event doesn't help you since only this driver has this issue. So nobody
will watch this event, unless it is sw specifically written for this SoC.

Much better to call vb2_queue_error to signal a fatal error (which this
apparently is) since there are more drivers that do this, and vivid supports
triggering this condition as well.

Regards,

	Hans
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Russell King - ARM Linux]

On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
> On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
> > The event must be user visible, otherwise the user has no indication
> > the error, and can't correct it by stream restart.
> 
> In that case the driver can detect this and call vb2_queue_error. It's
> what it is there for.
> 
> The event doesn't help you since only this driver has this issue. So nobody
> will watch this event, unless it is sw specifically written for this SoC.
> 
> Much better to call vb2_queue_error to signal a fatal error (which this
> apparently is) since there are more drivers that do this, and vivid supports
> triggering this condition as well.

So today, I can fiddle around with the IMX219 registers to help gain
an understanding of how this sensor works.  Several of the registers
(such as the PLL setup [*]) require me to disable streaming on the
sensor while changing them.

This is something I've done many times while testing various ideas,
and is my primary way of figuring out and testing such things.

Whenever I resume streaming (provided I've let the sensor stop
streaming at a frame boundary) it resumes as if nothing happened.  If I
stop the sensor mid-frame, then I get the rolling issue that Steve
reports, but once the top of the frame becomes aligned with the top of
the capture, everything then becomes stable again as if nothing happened.

The side effect of what you're proposing is that when I disable streaming
at the sensor by poking at its registers, rather than the capture just
stopping, an error is going to be delivered to gstreamer, and gstreamer
is going to exit, taking the entire capture process down.

This severely restricts the ability to be able to develop and test
sensor drivers.

So, I strongly disagree with you.

Loss of capture frames is not necessarily a fatal error - as I have been
saying repeatedly.  In Steve's case, there's some unknown interaction
between the source and iMX6 hardware that is causing the instability,
but that is simply not true of other sources, and I oppose any idea that
we should cripple the iMX6 side of the capture based upon just one
hardware combination where this is a problem.

Steve suggested that the problem could be in the iMX6 CSI block - and I
note comparing Steve's code with the code in FSL's repository that there
are some changes that are missing in Steve's code to do with the CCIR656
sync code setup, particularly for >8 bit.  The progressive CCIR656 8-bit
setup looks pretty similar though - but I think what needs to be asked
is whether the same problem is visible using the FSL/NXP vendor kernel.


* - the PLL setup is something that requires research at the moment.
Sony's official position (even to their customers) is that they do not
supply the necessary information, instead they expect customers to tell
them the capture settings they want, and Sony will throw the values into
a spreadsheet, and they'll supply the register settings back to the
customer.  Hence, the only way to proceed with a generic driver for
this sensor is to experiment, and experimenting requires the ability to
pause the stream at the sensor while making changes.  Take this away,
and we're stuck with the tables-of-register-settings-for-set-of-fixed-
capture-settings approach.  I've made a lot of progress away from this
which is all down to the flexibility afforded by _not_ killing the
capture process.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Russell King - ARM Linux]

On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
> On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
> > The event must be user visible, otherwise the user has no indication
> > the error, and can't correct it by stream restart.
> 
> In that case the driver can detect this and call vb2_queue_error. It's
> what it is there for.
> 
> The event doesn't help you since only this driver has this issue. So nobody
> will watch this event, unless it is sw specifically written for this SoC.
> 
> Much better to call vb2_queue_error to signal a fatal error (which this
> apparently is) since there are more drivers that do this, and vivid supports
> triggering this condition as well.

So today, I can fiddle around with the IMX219 registers to help gain
an understanding of how this sensor works.  Several of the registers
(such as the PLL setup [*]) require me to disable streaming on the
sensor while changing them.

This is something I've done many times while testing various ideas,
and is my primary way of figuring out and testing such things.

Whenever I resume streaming (provided I've let the sensor stop
streaming at a frame boundary) it resumes as if nothing happened.  If I
stop the sensor mid-frame, then I get the rolling issue that Steve
reports, but once the top of the frame becomes aligned with the top of
the capture, everything then becomes stable again as if nothing happened.

The side effect of what you're proposing is that when I disable streaming
at the sensor by poking at its registers, rather than the capture just
stopping, an error is going to be delivered to gstreamer, and gstreamer
is going to exit, taking the entire capture process down.

This severely restricts the ability to be able to develop and test
sensor drivers.

So, I strongly disagree with you.

Loss of capture frames is not necessarily a fatal error - as I have been
saying repeatedly.  In Steve's case, there's some unknown interaction
between the source and iMX6 hardware that is causing the instability,
but that is simply not true of other sources, and I oppose any idea that
we should cripple the iMX6 side of the capture based upon just one
hardware combination where this is a problem.

Steve suggested that the problem could be in the iMX6 CSI block - and I
note comparing Steve's code with the code in FSL's repository that there
are some changes that are missing in Steve's code to do with the CCIR656
sync code setup, particularly for >8 bit.  The progressive CCIR656 8-bit
setup looks pretty similar though - but I think what needs to be asked
is whether the same problem is visible using the FSL/NXP vendor kernel.


* - the PLL setup is something that requires research at the moment.
Sony's official position (even to their customers) is that they do not
supply the necessary information, instead they expect customers to tell
them the capture settings they want, and Sony will throw the values into
a spreadsheet, and they'll supply the register settings back to the
customer.  Hence, the only way to proceed with a generic driver for
this sensor is to experiment, and experimenting requires the ability to
pause the stream at the sensor while making changes.  Take this away,
and we're stuck with the tables-of-register-settings-for-set-of-fixed-
capture-settings approach.  I've made a lot of progress away from this
which is all down to the flexibility afforded by _not_ killing the
capture process.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Russell King - ARM Linux]

On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
> On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
> > The event must be user visible, otherwise the user has no indication
> > the error, and can't correct it by stream restart.
> 
> In that case the driver can detect this and call vb2_queue_error. It's
> what it is there for.
> 
> The event doesn't help you since only this driver has this issue. So nobody
> will watch this event, unless it is sw specifically written for this SoC.
> 
> Much better to call vb2_queue_error to signal a fatal error (which this
> apparently is) since there are more drivers that do this, and vivid supports
> triggering this condition as well.

So today, I can fiddle around with the IMX219 registers to help gain
an understanding of how this sensor works.  Several of the registers
(such as the PLL setup [*]) require me to disable streaming on the
sensor while changing them.

This is something I've done many times while testing various ideas,
and is my primary way of figuring out and testing such things.

Whenever I resume streaming (provided I've let the sensor stop
streaming at a frame boundary) it resumes as if nothing happened.  If I
stop the sensor mid-frame, then I get the rolling issue that Steve
reports, but once the top of the frame becomes aligned with the top of
the capture, everything then becomes stable again as if nothing happened.

The side effect of what you're proposing is that when I disable streaming
at the sensor by poking at its registers, rather than the capture just
stopping, an error is going to be delivered to gstreamer, and gstreamer
is going to exit, taking the entire capture process down.

This severely restricts the ability to be able to develop and test
sensor drivers.

So, I strongly disagree with you.

Loss of capture frames is not necessarily a fatal error - as I have been
saying repeatedly.  In Steve's case, there's some unknown interaction
between the source and iMX6 hardware that is causing the instability,
but that is simply not true of other sources, and I oppose any idea that
we should cripple the iMX6 side of the capture based upon just one
hardware combination where this is a problem.

Steve suggested that the problem could be in the iMX6 CSI block - and I
note comparing Steve's code with the code in FSL's repository that there
are some changes that are missing in Steve's code to do with the CCIR656
sync code setup, particularly for >8 bit.  The progressive CCIR656 8-bit
setup looks pretty similar though - but I think what needs to be asked
is whether the same problem is visible using the FSL/NXP vendor kernel.


* - the PLL setup is something that requires research at the moment.
Sony's official position (even to their customers) is that they do not
supply the necessary information, instead they expect customers to tell
them the capture settings they want, and Sony will throw the values into
a spreadsheet, and they'll supply the register settings back to the
customer.  Hence, the only way to proceed with a generic driver for
this sensor is to experiment, and experimenting requires the ability to
pause the stream at the sensor while making changes.  Take this away,
and we're stuck with the tables-of-register-settings-for-set-of-fixed-
capture-settings approach.  I've made a lot of progress away from this
which is all down to the flexibility afforded by _not_ killing the
capture process.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Hans Verkuil]

On 03/13/2017 11:45 AM, Russell King - ARM Linux wrote:
> On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
>> On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
>>> The event must be user visible, otherwise the user has no indication
>>> the error, and can't correct it by stream restart.
>>
>> In that case the driver can detect this and call vb2_queue_error. It's
>> what it is there for.
>>
>> The event doesn't help you since only this driver has this issue. So nobody
>> will watch this event, unless it is sw specifically written for this SoC.
>>
>> Much better to call vb2_queue_error to signal a fatal error (which this
>> apparently is) since there are more drivers that do this, and vivid supports
>> triggering this condition as well.
> 
> So today, I can fiddle around with the IMX219 registers to help gain
> an understanding of how this sensor works.  Several of the registers
> (such as the PLL setup [*]) require me to disable streaming on the
> sensor while changing them.
> 
> This is something I've done many times while testing various ideas,
> and is my primary way of figuring out and testing such things.
> 
> Whenever I resume streaming (provided I've let the sensor stop
> streaming at a frame boundary) it resumes as if nothing happened.  If I
> stop the sensor mid-frame, then I get the rolling issue that Steve
> reports, but once the top of the frame becomes aligned with the top of
> the capture, everything then becomes stable again as if nothing happened.
> 
> The side effect of what you're proposing is that when I disable streaming
> at the sensor by poking at its registers, rather than the capture just
> stopping, an error is going to be delivered to gstreamer, and gstreamer
> is going to exit, taking the entire capture process down.
> 
> This severely restricts the ability to be able to develop and test
> sensor drivers.
> 
> So, I strongly disagree with you.
> 
> Loss of capture frames is not necessarily a fatal error - as I have been
> saying repeatedly.  In Steve's case, there's some unknown interaction
> between the source and iMX6 hardware that is causing the instability,
> but that is simply not true of other sources, and I oppose any idea that
> we should cripple the iMX6 side of the capture based upon just one
> hardware combination where this is a problem.
> 
> Steve suggested that the problem could be in the iMX6 CSI block - and I
> note comparing Steve's code with the code in FSL's repository that there
> are some changes that are missing in Steve's code to do with the CCIR656
> sync code setup, particularly for >8 bit.  The progressive CCIR656 8-bit
> setup looks pretty similar though - but I think what needs to be asked
> is whether the same problem is visible using the FSL/NXP vendor kernel.
> 
> 
> * - the PLL setup is something that requires research at the moment.
> Sony's official position (even to their customers) is that they do not
> supply the necessary information, instead they expect customers to tell
> them the capture settings they want, and Sony will throw the values into
> a spreadsheet, and they'll supply the register settings back to the
> customer.  Hence, the only way to proceed with a generic driver for
> this sensor is to experiment, and experimenting requires the ability to
> pause the stream at the sensor while making changes.  Take this away,
> and we're stuck with the tables-of-register-settings-for-set-of-fixed-
> capture-settings approach.  I've made a lot of progress away from this
> which is all down to the flexibility afforded by _not_ killing the
> capture process.
> 

In other words: Steve should either find a proper fix for this, or only
call vb2_queue_error in this specific case. Sending an event that nobody
will know how to handle or what to do with is pretty pointless IMHO.

Let's just give him time to try and figure out the real issue here.

Regards,

	Hans

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Hans Verkuil]

On 03/13/2017 11:45 AM, Russell King - ARM Linux wrote:
> On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
>> On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
>>> The event must be user visible, otherwise the user has no indication
>>> the error, and can't correct it by stream restart.
>>
>> In that case the driver can detect this and call vb2_queue_error. It's
>> what it is there for.
>>
>> The event doesn't help you since only this driver has this issue. So nobody
>> will watch this event, unless it is sw specifically written for this SoC.
>>
>> Much better to call vb2_queue_error to signal a fatal error (which this
>> apparently is) since there are more drivers that do this, and vivid supports
>> triggering this condition as well.
> 
> So today, I can fiddle around with the IMX219 registers to help gain
> an understanding of how this sensor works.  Several of the registers
> (such as the PLL setup [*]) require me to disable streaming on the
> sensor while changing them.
> 
> This is something I've done many times while testing various ideas,
> and is my primary way of figuring out and testing such things.
> 
> Whenever I resume streaming (provided I've let the sensor stop
> streaming at a frame boundary) it resumes as if nothing happened.  If I
> stop the sensor mid-frame, then I get the rolling issue that Steve
> reports, but once the top of the frame becomes aligned with the top of
> the capture, everything then becomes stable again as if nothing happened.
> 
> The side effect of what you're proposing is that when I disable streaming
> at the sensor by poking at its registers, rather than the capture just
> stopping, an error is going to be delivered to gstreamer, and gstreamer
> is going to exit, taking the entire capture process down.
> 
> This severely restricts the ability to be able to develop and test
> sensor drivers.
> 
> So, I strongly disagree with you.
> 
> Loss of capture frames is not necessarily a fatal error - as I have been
> saying repeatedly.  In Steve's case, there's some unknown interaction
> between the source and iMX6 hardware that is causing the instability,
> but that is simply not true of other sources, and I oppose any idea that
> we should cripple the iMX6 side of the capture based upon just one
> hardware combination where this is a problem.
> 
> Steve suggested that the problem could be in the iMX6 CSI block - and I
> note comparing Steve's code with the code in FSL's repository that there
> are some changes that are missing in Steve's code to do with the CCIR656
> sync code setup, particularly for >8 bit.  The progressive CCIR656 8-bit
> setup looks pretty similar though - but I think what needs to be asked
> is whether the same problem is visible using the FSL/NXP vendor kernel.
> 
> 
> * - the PLL setup is something that requires research at the moment.
> Sony's official position (even to their customers) is that they do not
> supply the necessary information, instead they expect customers to tell
> them the capture settings they want, and Sony will throw the values into
> a spreadsheet, and they'll supply the register settings back to the
> customer.  Hence, the only way to proceed with a generic driver for
> this sensor is to experiment, and experimenting requires the ability to
> pause the stream at the sensor while making changes.  Take this away,
> and we're stuck with the tables-of-register-settings-for-set-of-fixed-
> capture-settings approach.  I've made a lot of progress away from this
> which is all down to the flexibility afforded by _not_ killing the
> capture process.
> 

In other words: Steve should either find a proper fix for this, or only
call vb2_queue_error in this specific case. Sending an event that nobody
will know how to handle or what to do with is pretty pointless IMHO.

Let's just give him time to try and figure out the real issue here.

Regards,

	Hans

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Hans Verkuil]

On 03/13/2017 11:45 AM, Russell King - ARM Linux wrote:
> On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
>> On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
>>> The event must be user visible, otherwise the user has no indication
>>> the error, and can't correct it by stream restart.
>>
>> In that case the driver can detect this and call vb2_queue_error. It's
>> what it is there for.
>>
>> The event doesn't help you since only this driver has this issue. So nobody
>> will watch this event, unless it is sw specifically written for this SoC.
>>
>> Much better to call vb2_queue_error to signal a fatal error (which this
>> apparently is) since there are more drivers that do this, and vivid supports
>> triggering this condition as well.
> 
> So today, I can fiddle around with the IMX219 registers to help gain
> an understanding of how this sensor works.  Several of the registers
> (such as the PLL setup [*]) require me to disable streaming on the
> sensor while changing them.
> 
> This is something I've done many times while testing various ideas,
> and is my primary way of figuring out and testing such things.
> 
> Whenever I resume streaming (provided I've let the sensor stop
> streaming at a frame boundary) it resumes as if nothing happened.  If I
> stop the sensor mid-frame, then I get the rolling issue that Steve
> reports, but once the top of the frame becomes aligned with the top of
> the capture, everything then becomes stable again as if nothing happened.
> 
> The side effect of what you're proposing is that when I disable streaming
> at the sensor by poking at its registers, rather than the capture just
> stopping, an error is going to be delivered to gstreamer, and gstreamer
> is going to exit, taking the entire capture process down.
> 
> This severely restricts the ability to be able to develop and test
> sensor drivers.
> 
> So, I strongly disagree with you.
> 
> Loss of capture frames is not necessarily a fatal error - as I have been
> saying repeatedly.  In Steve's case, there's some unknown interaction
> between the source and iMX6 hardware that is causing the instability,
> but that is simply not true of other sources, and I oppose any idea that
> we should cripple the iMX6 side of the capture based upon just one
> hardware combination where this is a problem.
> 
> Steve suggested that the problem could be in the iMX6 CSI block - and I
> note comparing Steve's code with the code in FSL's repository that there
> are some changes that are missing in Steve's code to do with the CCIR656
> sync code setup, particularly for >8 bit.  The progressive CCIR656 8-bit
> setup looks pretty similar though - but I think what needs to be asked
> is whether the same problem is visible using the FSL/NXP vendor kernel.
> 
> 
> * - the PLL setup is something that requires research at the moment.
> Sony's official position (even to their customers) is that they do not
> supply the necessary information, instead they expect customers to tell
> them the capture settings they want, and Sony will throw the values into
> a spreadsheet, and they'll supply the register settings back to the
> customer.  Hence, the only way to proceed with a generic driver for
> this sensor is to experiment, and experimenting requires the ability to
> pause the stream at the sensor while making changes.  Take this away,
> and we're stuck with the tables-of-register-settings-for-set-of-fixed-
> capture-settings approach.  I've made a lot of progress away from this
> which is all down to the flexibility afforded by _not_ killing the
> capture process.
> 

In other words: Steve should either find a proper fix for this, or only
call vb2_queue_error in this specific case. Sending an event that nobody
will know how to handle or what to do with is pretty pointless IMHO.

Let's just give him time to try and figure out the real issue here.

Regards,

	Hans
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/13/2017 03:53 AM, Hans Verkuil wrote:
> On 03/13/2017 11:45 AM, Russell King - ARM Linux wrote:
>> On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
>>> On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
>>>> The event must be user visible, otherwise the user has no indication
>>>> the error, and can't correct it by stream restart.
>>>
>>> In that case the driver can detect this and call vb2_queue_error. It's
>>> what it is there for.
>>>
>>> The event doesn't help you since only this driver has this issue. So nobody
>>> will watch this event, unless it is sw specifically written for this SoC.
>>>
>>> Much better to call vb2_queue_error to signal a fatal error (which this
>>> apparently is) since there are more drivers that do this, and vivid supports
>>> triggering this condition as well.
>>
>> So today, I can fiddle around with the IMX219 registers to help gain
>> an understanding of how this sensor works.  Several of the registers
>> (such as the PLL setup [*]) require me to disable streaming on the
>> sensor while changing them.
>>
>> This is something I've done many times while testing various ideas,
>> and is my primary way of figuring out and testing such things.
>>
>> Whenever I resume streaming (provided I've let the sensor stop
>> streaming at a frame boundary) it resumes as if nothing happened.  If I
>> stop the sensor mid-frame, then I get the rolling issue that Steve
>> reports, but once the top of the frame becomes aligned with the top of
>> the capture, everything then becomes stable again as if nothing happened.
>>
>> The side effect of what you're proposing is that when I disable streaming
>> at the sensor by poking at its registers, rather than the capture just
>> stopping, an error is going to be delivered to gstreamer, and gstreamer
>> is going to exit, taking the entire capture process down.
>>
>> This severely restricts the ability to be able to develop and test
>> sensor drivers.
>>
>> So, I strongly disagree with you.
>>
>> Loss of capture frames is not necessarily a fatal error - as I have been
>> saying repeatedly.  In Steve's case, there's some unknown interaction
>> between the source and iMX6 hardware that is causing the instability,
>> but that is simply not true of other sources, and I oppose any idea that
>> we should cripple the iMX6 side of the capture based upon just one
>> hardware combination where this is a problem.
>>
>> Steve suggested that the problem could be in the iMX6 CSI block - and I
>> note comparing Steve's code with the code in FSL's repository that there
>> are some changes that are missing in Steve's code to do with the CCIR656
>> sync code setup, particularly for >8 bit.  The progressive CCIR656 8-bit
>> setup looks pretty similar though - but I think what needs to be asked
>> is whether the same problem is visible using the FSL/NXP vendor kernel.
>>
>>
>> * - the PLL setup is something that requires research at the moment.
>> Sony's official position (even to their customers) is that they do not
>> supply the necessary information, instead they expect customers to tell
>> them the capture settings they want, and Sony will throw the values into
>> a spreadsheet, and they'll supply the register settings back to the
>> customer.  Hence, the only way to proceed with a generic driver for
>> this sensor is to experiment, and experimenting requires the ability to
>> pause the stream at the sensor while making changes.  Take this away,
>> and we're stuck with the tables-of-register-settings-for-set-of-fixed-
>> capture-settings approach.  I've made a lot of progress away from this
>> which is all down to the flexibility afforded by _not_ killing the
>> capture process.
>>
>
> In other words: Steve should either find a proper fix for this, or only
> call vb2_queue_error in this specific case. Sending an event that nobody
> will know how to handle or what to do with is pretty pointless IMHO.
>
> Let's just give him time to try and figure out the real issue here.


This is a long-standing issue, I've traveled to Hildesheim working with
our customer to try and get to the bottom of it. I can go into a lot of
details from those trips, we probed the bt.656 bus with a logic analyzer
and I can share those results with anyone who asks. But the results of
those investigations indicate the CSI is not handling the SAV/EAV sync
codes correctly - if there is a shift in the line position at which
those codes occur, the CSI/IPU does not abort the frame capture DMA
and start from the new sync code position, it just continues to capture
lines until the programmed number of lines are transferred, hence you
get these split images. Freescale also informed us of a mechanism in the
IPU that will add lines if it detects these short frames, until the
programmed number of lines are reached. Apparently that is what creates 
the rolling effect, but this rolling can last for up to a full minute,
which is completely unacceptable, it must be corrected as soon as
possible.

So the only thing we could come up with was to monitor frame intervals,
this is purely empirical, but we observed that frame intervals drop
by approx. one line time (~60 usec) when these short frames are
received. I don't really have any explanation for that but we take
advantage of that observation by sending this event to userspace so
the problem can be corrected immediately with a stream restart.

As I've said, the ADV718x does not provide _any_ indication via status
when the shift in the sync code position occurs. And the IPU is also 
severely lacking in DMA completion status as well (no short packet
status like in USB for example). So the only way to detect this event
is by monitoring the frame intervals.

I will review differences in the CCIR code register setup from FSL's
repo that Russell pointed out, but I'm fairly sure those code registers
are setup correctly, there's not much room for variability in those
values. They only define the values of the sync codes, so the CSI can
detect them, those values are defined by the bt.656 spec.

Anyway, perhaps for now I can remove the event, but keep the FI
monitoring, and for now just report a kernel error message on
a detected bad FI.

Steve

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/13/2017 03:53 AM, Hans Verkuil wrote:
> On 03/13/2017 11:45 AM, Russell King - ARM Linux wrote:
>> On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
>>> On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
>>>> The event must be user visible, otherwise the user has no indication
>>>> the error, and can't correct it by stream restart.
>>>
>>> In that case the driver can detect this and call vb2_queue_error. It's
>>> what it is there for.
>>>
>>> The event doesn't help you since only this driver has this issue. So nobody
>>> will watch this event, unless it is sw specifically written for this SoC.
>>>
>>> Much better to call vb2_queue_error to signal a fatal error (which this
>>> apparently is) since there are more drivers that do this, and vivid supports
>>> triggering this condition as well.
>>
>> So today, I can fiddle around with the IMX219 registers to help gain
>> an understanding of how this sensor works.  Several of the registers
>> (such as the PLL setup [*]) require me to disable streaming on the
>> sensor while changing them.
>>
>> This is something I've done many times while testing various ideas,
>> and is my primary way of figuring out and testing such things.
>>
>> Whenever I resume streaming (provided I've let the sensor stop
>> streaming at a frame boundary) it resumes as if nothing happened.  If I
>> stop the sensor mid-frame, then I get the rolling issue that Steve
>> reports, but once the top of the frame becomes aligned with the top of
>> the capture, everything then becomes stable again as if nothing happened.
>>
>> The side effect of what you're proposing is that when I disable streaming
>> at the sensor by poking at its registers, rather than the capture just
>> stopping, an error is going to be delivered to gstreamer, and gstreamer
>> is going to exit, taking the entire capture process down.
>>
>> This severely restricts the ability to be able to develop and test
>> sensor drivers.
>>
>> So, I strongly disagree with you.
>>
>> Loss of capture frames is not necessarily a fatal error - as I have been
>> saying repeatedly.  In Steve's case, there's some unknown interaction
>> between the source and iMX6 hardware that is causing the instability,
>> but that is simply not true of other sources, and I oppose any idea that
>> we should cripple the iMX6 side of the capture based upon just one
>> hardware combination where this is a problem.
>>
>> Steve suggested that the problem could be in the iMX6 CSI block - and I
>> note comparing Steve's code with the code in FSL's repository that there
>> are some changes that are missing in Steve's code to do with the CCIR656
>> sync code setup, particularly for >8 bit.  The progressive CCIR656 8-bit
>> setup looks pretty similar though - but I think what needs to be asked
>> is whether the same problem is visible using the FSL/NXP vendor kernel.
>>
>>
>> * - the PLL setup is something that requires research at the moment.
>> Sony's official position (even to their customers) is that they do not
>> supply the necessary information, instead they expect customers to tell
>> them the capture settings they want, and Sony will throw the values into
>> a spreadsheet, and they'll supply the register settings back to the
>> customer.  Hence, the only way to proceed with a generic driver for
>> this sensor is to experiment, and experimenting requires the ability to
>> pause the stream at the sensor while making changes.  Take this away,
>> and we're stuck with the tables-of-register-settings-for-set-of-fixed-
>> capture-settings approach.  I've made a lot of progress away from this
>> which is all down to the flexibility afforded by _not_ killing the
>> capture process.
>>
>
> In other words: Steve should either find a proper fix for this, or only
> call vb2_queue_error in this specific case. Sending an event that nobody
> will know how to handle or what to do with is pretty pointless IMHO.
>
> Let's just give him time to try and figure out the real issue here.


This is a long-standing issue, I've traveled to Hildesheim working with
our customer to try and get to the bottom of it. I can go into a lot of
details from those trips, we probed the bt.656 bus with a logic analyzer
and I can share those results with anyone who asks. But the results of
those investigations indicate the CSI is not handling the SAV/EAV sync
codes correctly - if there is a shift in the line position at which
those codes occur, the CSI/IPU does not abort the frame capture DMA
and start from the new sync code position, it just continues to capture
lines until the programmed number of lines are transferred, hence you
get these split images. Freescale also informed us of a mechanism in the
IPU that will add lines if it detects these short frames, until the
programmed number of lines are reached. Apparently that is what creates 
the rolling effect, but this rolling can last for up to a full minute,
which is completely unacceptable, it must be corrected as soon as
possible.

So the only thing we could come up with was to monitor frame intervals,
this is purely empirical, but we observed that frame intervals drop
by approx. one line time (~60 usec) when these short frames are
received. I don't really have any explanation for that but we take
advantage of that observation by sending this event to userspace so
the problem can be corrected immediately with a stream restart.

As I've said, the ADV718x does not provide _any_ indication via status
when the shift in the sync code position occurs. And the IPU is also 
severely lacking in DMA completion status as well (no short packet
status like in USB for example). So the only way to detect this event
is by monitoring the frame intervals.

I will review differences in the CCIR code register setup from FSL's
repo that Russell pointed out, but I'm fairly sure those code registers
are setup correctly, there's not much room for variability in those
values. They only define the values of the sync codes, so the CSI can
detect them, those values are defined by the bt.656 spec.

Anyway, perhaps for now I can remove the event, but keep the FI
monitoring, and for now just report a kernel error message on
a detected bad FI.

Steve

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/13/2017 03:53 AM, Hans Verkuil wrote:
> On 03/13/2017 11:45 AM, Russell King - ARM Linux wrote:
>> On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
>>> On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
>>>> The event must be user visible, otherwise the user has no indication
>>>> the error, and can't correct it by stream restart.
>>>
>>> In that case the driver can detect this and call vb2_queue_error. It's
>>> what it is there for.
>>>
>>> The event doesn't help you since only this driver has this issue. So nobody
>>> will watch this event, unless it is sw specifically written for this SoC.
>>>
>>> Much better to call vb2_queue_error to signal a fatal error (which this
>>> apparently is) since there are more drivers that do this, and vivid supports
>>> triggering this condition as well.
>>
>> So today, I can fiddle around with the IMX219 registers to help gain
>> an understanding of how this sensor works.  Several of the registers
>> (such as the PLL setup [*]) require me to disable streaming on the
>> sensor while changing them.
>>
>> This is something I've done many times while testing various ideas,
>> and is my primary way of figuring out and testing such things.
>>
>> Whenever I resume streaming (provided I've let the sensor stop
>> streaming at a frame boundary) it resumes as if nothing happened.  If I
>> stop the sensor mid-frame, then I get the rolling issue that Steve
>> reports, but once the top of the frame becomes aligned with the top of
>> the capture, everything then becomes stable again as if nothing happened.
>>
>> The side effect of what you're proposing is that when I disable streaming
>> at the sensor by poking at its registers, rather than the capture just
>> stopping, an error is going to be delivered to gstreamer, and gstreamer
>> is going to exit, taking the entire capture process down.
>>
>> This severely restricts the ability to be able to develop and test
>> sensor drivers.
>>
>> So, I strongly disagree with you.
>>
>> Loss of capture frames is not necessarily a fatal error - as I have been
>> saying repeatedly.  In Steve's case, there's some unknown interaction
>> between the source and iMX6 hardware that is causing the instability,
>> but that is simply not true of other sources, and I oppose any idea that
>> we should cripple the iMX6 side of the capture based upon just one
>> hardware combination where this is a problem.
>>
>> Steve suggested that the problem could be in the iMX6 CSI block - and I
>> note comparing Steve's code with the code in FSL's repository that there
>> are some changes that are missing in Steve's code to do with the CCIR656
>> sync code setup, particularly for >8 bit.  The progressive CCIR656 8-bit
>> setup looks pretty similar though - but I think what needs to be asked
>> is whether the same problem is visible using the FSL/NXP vendor kernel.
>>
>>
>> * - the PLL setup is something that requires research at the moment.
>> Sony's official position (even to their customers) is that they do not
>> supply the necessary information, instead they expect customers to tell
>> them the capture settings they want, and Sony will throw the values into
>> a spreadsheet, and they'll supply the register settings back to the
>> customer.  Hence, the only way to proceed with a generic driver for
>> this sensor is to experiment, and experimenting requires the ability to
>> pause the stream at the sensor while making changes.  Take this away,
>> and we're stuck with the tables-of-register-settings-for-set-of-fixed-
>> capture-settings approach.  I've made a lot of progress away from this
>> which is all down to the flexibility afforded by _not_ killing the
>> capture process.
>>
>
> In other words: Steve should either find a proper fix for this, or only
> call vb2_queue_error in this specific case. Sending an event that nobody
> will know how to handle or what to do with is pretty pointless IMHO.
>
> Let's just give him time to try and figure out the real issue here.


This is a long-standing issue, I've traveled to Hildesheim working with
our customer to try and get to the bottom of it. I can go into a lot of
details from those trips, we probed the bt.656 bus with a logic analyzer
and I can share those results with anyone who asks. But the results of
those investigations indicate the CSI is not handling the SAV/EAV sync
codes correctly - if there is a shift in the line position at which
those codes occur, the CSI/IPU does not abort the frame capture DMA
and start from the new sync code position, it just continues to capture
lines until the programmed number of lines are transferred, hence you
get these split images. Freescale also informed us of a mechanism in the
IPU that will add lines if it detects these short frames, until the
programmed number of lines are reached. Apparently that is what creates 
the rolling effect, but this rolling can last for up to a full minute,
which is completely unacceptable, it must be corrected as soon as
possible.

So the only thing we could come up with was to monitor frame intervals,
this is purely empirical, but we observed that frame intervals drop
by approx. one line time (~60 usec) when these short frames are
received. I don't really have any explanation for that but we take
advantage of that observation by sending this event to userspace so
the problem can be corrected immediately with a stream restart.

As I've said, the ADV718x does not provide _any_ indication via status
when the shift in the sync code position occurs. And the IPU is also 
severely lacking in DMA completion status as well (no short packet
status like in USB for example). So the only way to detect this event
is by monitoring the frame intervals.

I will review differences in the CCIR code register setup from FSL's
repo that Russell pointed out, but I'm fairly sure those code registers
are setup correctly, there's not much room for variability in those
values. They only define the values of the sync codes, so the CSI can
detect them, those values are defined by the bt.656 spec.

Anyway, perhaps for now I can remove the event, but keep the FI
monitoring, and for now just report a kernel error message on
a detected bad FI.

Steve

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Hans Verkuil]

On 03/13/2017 06:06 PM, Steve Longerbeam wrote:
> 
> 
> On 03/13/2017 03:53 AM, Hans Verkuil wrote:
>> On 03/13/2017 11:45 AM, Russell King - ARM Linux wrote:
>>> On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
>>>> On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
>>>>> The event must be user visible, otherwise the user has no indication
>>>>> the error, and can't correct it by stream restart.
>>>>
>>>> In that case the driver can detect this and call vb2_queue_error. It's
>>>> what it is there for.
>>>>
>>>> The event doesn't help you since only this driver has this issue. So nobody
>>>> will watch this event, unless it is sw specifically written for this SoC.
>>>>
>>>> Much better to call vb2_queue_error to signal a fatal error (which this
>>>> apparently is) since there are more drivers that do this, and vivid supports
>>>> triggering this condition as well.
>>>
>>> So today, I can fiddle around with the IMX219 registers to help gain
>>> an understanding of how this sensor works.  Several of the registers
>>> (such as the PLL setup [*]) require me to disable streaming on the
>>> sensor while changing them.
>>>
>>> This is something I've done many times while testing various ideas,
>>> and is my primary way of figuring out and testing such things.
>>>
>>> Whenever I resume streaming (provided I've let the sensor stop
>>> streaming at a frame boundary) it resumes as if nothing happened.  If I
>>> stop the sensor mid-frame, then I get the rolling issue that Steve
>>> reports, but once the top of the frame becomes aligned with the top of
>>> the capture, everything then becomes stable again as if nothing happened.
>>>
>>> The side effect of what you're proposing is that when I disable streaming
>>> at the sensor by poking at its registers, rather than the capture just
>>> stopping, an error is going to be delivered to gstreamer, and gstreamer
>>> is going to exit, taking the entire capture process down.
>>>
>>> This severely restricts the ability to be able to develop and test
>>> sensor drivers.
>>>
>>> So, I strongly disagree with you.
>>>
>>> Loss of capture frames is not necessarily a fatal error - as I have been
>>> saying repeatedly.  In Steve's case, there's some unknown interaction
>>> between the source and iMX6 hardware that is causing the instability,
>>> but that is simply not true of other sources, and I oppose any idea that
>>> we should cripple the iMX6 side of the capture based upon just one
>>> hardware combination where this is a problem.
>>>
>>> Steve suggested that the problem could be in the iMX6 CSI block - and I
>>> note comparing Steve's code with the code in FSL's repository that there
>>> are some changes that are missing in Steve's code to do with the CCIR656
>>> sync code setup, particularly for >8 bit.  The progressive CCIR656 8-bit
>>> setup looks pretty similar though - but I think what needs to be asked
>>> is whether the same problem is visible using the FSL/NXP vendor kernel.
>>>
>>>
>>> * - the PLL setup is something that requires research at the moment.
>>> Sony's official position (even to their customers) is that they do not
>>> supply the necessary information, instead they expect customers to tell
>>> them the capture settings they want, and Sony will throw the values into
>>> a spreadsheet, and they'll supply the register settings back to the
>>> customer.  Hence, the only way to proceed with a generic driver for
>>> this sensor is to experiment, and experimenting requires the ability to
>>> pause the stream at the sensor while making changes.  Take this away,
>>> and we're stuck with the tables-of-register-settings-for-set-of-fixed-
>>> capture-settings approach.  I've made a lot of progress away from this
>>> which is all down to the flexibility afforded by _not_ killing the
>>> capture process.
>>>
>>
>> In other words: Steve should either find a proper fix for this, or only
>> call vb2_queue_error in this specific case. Sending an event that nobody
>> will know how to handle or what to do with is pretty pointless IMHO.
>>
>> Let's just give him time to try and figure out the real issue here.
> 
> 
> This is a long-standing issue, I've traveled to Hildesheim working with
> our customer to try and get to the bottom of it. I can go into a lot of
> details from those trips, we probed the bt.656 bus with a logic analyzer
> and I can share those results with anyone who asks. But the results of
> those investigations indicate the CSI is not handling the SAV/EAV sync
> codes correctly - if there is a shift in the line position at which
> those codes occur, the CSI/IPU does not abort the frame capture DMA
> and start from the new sync code position, it just continues to capture
> lines until the programmed number of lines are transferred, hence you
> get these split images. Freescale also informed us of a mechanism in the
> IPU that will add lines if it detects these short frames, until the
> programmed number of lines are reached. Apparently that is what creates 
> the rolling effect, but this rolling can last for up to a full minute,
> which is completely unacceptable, it must be corrected as soon as
> possible.
> 
> So the only thing we could come up with was to monitor frame intervals,
> this is purely empirical, but we observed that frame intervals drop
> by approx. one line time (~60 usec) when these short frames are
> received. I don't really have any explanation for that but we take
> advantage of that observation by sending this event to userspace so
> the problem can be corrected immediately with a stream restart.
> 
> As I've said, the ADV718x does not provide _any_ indication via status
> when the shift in the sync code position occurs. And the IPU is also 
> severely lacking in DMA completion status as well (no short packet
> status like in USB for example). So the only way to detect this event
> is by monitoring the frame intervals.
> 
> I will review differences in the CCIR code register setup from FSL's
> repo that Russell pointed out, but I'm fairly sure those code registers
> are setup correctly, there's not much room for variability in those
> values. They only define the values of the sync codes, so the CSI can
> detect them, those values are defined by the bt.656 spec.
> 
> Anyway, perhaps for now I can remove the event, but keep the FI
> monitoring, and for now just report a kernel error message on
> a detected bad FI.

Is it possible to detect this specific situation? Apparently this issue
is not present (or at least resolves itself very quickly) on the imx219.

If it is not possible, then a private event would be acceptable, but
needs to be carefully documented. After all, it is a workaround for a bug,
since otherwise there would be no need for this event.

Regards,

	Hans

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Hans Verkuil]

On 03/13/2017 06:06 PM, Steve Longerbeam wrote:
> 
> 
> On 03/13/2017 03:53 AM, Hans Verkuil wrote:
>> On 03/13/2017 11:45 AM, Russell King - ARM Linux wrote:
>>> On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
>>>> On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
>>>>> The event must be user visible, otherwise the user has no indication
>>>>> the error, and can't correct it by stream restart.
>>>>
>>>> In that case the driver can detect this and call vb2_queue_error. It's
>>>> what it is there for.
>>>>
>>>> The event doesn't help you since only this driver has this issue. So nobody
>>>> will watch this event, unless it is sw specifically written for this SoC.
>>>>
>>>> Much better to call vb2_queue_error to signal a fatal error (which this
>>>> apparently is) since there are more drivers that do this, and vivid supports
>>>> triggering this condition as well.
>>>
>>> So today, I can fiddle around with the IMX219 registers to help gain
>>> an understanding of how this sensor works.  Several of the registers
>>> (such as the PLL setup [*]) require me to disable streaming on the
>>> sensor while changing them.
>>>
>>> This is something I've done many times while testing various ideas,
>>> and is my primary way of figuring out and testing such things.
>>>
>>> Whenever I resume streaming (provided I've let the sensor stop
>>> streaming at a frame boundary) it resumes as if nothing happened.  If I
>>> stop the sensor mid-frame, then I get the rolling issue that Steve
>>> reports, but once the top of the frame becomes aligned with the top of
>>> the capture, everything then becomes stable again as if nothing happened.
>>>
>>> The side effect of what you're proposing is that when I disable streaming
>>> at the sensor by poking at its registers, rather than the capture just
>>> stopping, an error is going to be delivered to gstreamer, and gstreamer
>>> is going to exit, taking the entire capture process down.
>>>
>>> This severely restricts the ability to be able to develop and test
>>> sensor drivers.
>>>
>>> So, I strongly disagree with you.
>>>
>>> Loss of capture frames is not necessarily a fatal error - as I have been
>>> saying repeatedly.  In Steve's case, there's some unknown interaction
>>> between the source and iMX6 hardware that is causing the instability,
>>> but that is simply not true of other sources, and I oppose any idea that
>>> we should cripple the iMX6 side of the capture based upon just one
>>> hardware combination where this is a problem.
>>>
>>> Steve suggested that the problem could be in the iMX6 CSI block - and I
>>> note comparing Steve's code with the code in FSL's repository that there
>>> are some changes that are missing in Steve's code to do with the CCIR656
>>> sync code setup, particularly for >8 bit.  The progressive CCIR656 8-bit
>>> setup looks pretty similar though - but I think what needs to be asked
>>> is whether the same problem is visible using the FSL/NXP vendor kernel.
>>>
>>>
>>> * - the PLL setup is something that requires research at the moment.
>>> Sony's official position (even to their customers) is that they do not
>>> supply the necessary information, instead they expect customers to tell
>>> them the capture settings they want, and Sony will throw the values into
>>> a spreadsheet, and they'll supply the register settings back to the
>>> customer.  Hence, the only way to proceed with a generic driver for
>>> this sensor is to experiment, and experimenting requires the ability to
>>> pause the stream at the sensor while making changes.  Take this away,
>>> and we're stuck with the tables-of-register-settings-for-set-of-fixed-
>>> capture-settings approach.  I've made a lot of progress away from this
>>> which is all down to the flexibility afforded by _not_ killing the
>>> capture process.
>>>
>>
>> In other words: Steve should either find a proper fix for this, or only
>> call vb2_queue_error in this specific case. Sending an event that nobody
>> will know how to handle or what to do with is pretty pointless IMHO.
>>
>> Let's just give him time to try and figure out the real issue here.
> 
> 
> This is a long-standing issue, I've traveled to Hildesheim working with
> our customer to try and get to the bottom of it. I can go into a lot of
> details from those trips, we probed the bt.656 bus with a logic analyzer
> and I can share those results with anyone who asks. But the results of
> those investigations indicate the CSI is not handling the SAV/EAV sync
> codes correctly - if there is a shift in the line position at which
> those codes occur, the CSI/IPU does not abort the frame capture DMA
> and start from the new sync code position, it just continues to capture
> lines until the programmed number of lines are transferred, hence you
> get these split images. Freescale also informed us of a mechanism in the
> IPU that will add lines if it detects these short frames, until the
> programmed number of lines are reached. Apparently that is what creates 
> the rolling effect, but this rolling can last for up to a full minute,
> which is completely unacceptable, it must be corrected as soon as
> possible.
> 
> So the only thing we could come up with was to monitor frame intervals,
> this is purely empirical, but we observed that frame intervals drop
> by approx. one line time (~60 usec) when these short frames are
> received. I don't really have any explanation for that but we take
> advantage of that observation by sending this event to userspace so
> the problem can be corrected immediately with a stream restart.
> 
> As I've said, the ADV718x does not provide _any_ indication via status
> when the shift in the sync code position occurs. And the IPU is also 
> severely lacking in DMA completion status as well (no short packet
> status like in USB for example). So the only way to detect this event
> is by monitoring the frame intervals.
> 
> I will review differences in the CCIR code register setup from FSL's
> repo that Russell pointed out, but I'm fairly sure those code registers
> are setup correctly, there's not much room for variability in those
> values. They only define the values of the sync codes, so the CSI can
> detect them, those values are defined by the bt.656 spec.
> 
> Anyway, perhaps for now I can remove the event, but keep the FI
> monitoring, and for now just report a kernel error message on
> a detected bad FI.

Is it possible to detect this specific situation? Apparently this issue
is not present (or at least resolves itself very quickly) on the imx219.

If it is not possible, then a private event would be acceptable, but
needs to be carefully documented. After all, it is a workaround for a bug,
since otherwise there would be no need for this event.

Regards,

	Hans

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Hans Verkuil]

On 03/13/2017 06:06 PM, Steve Longerbeam wrote:
> 
> 
> On 03/13/2017 03:53 AM, Hans Verkuil wrote:
>> On 03/13/2017 11:45 AM, Russell King - ARM Linux wrote:
>>> On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
>>>> On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
>>>>> The event must be user visible, otherwise the user has no indication
>>>>> the error, and can't correct it by stream restart.
>>>>
>>>> In that case the driver can detect this and call vb2_queue_error. It's
>>>> what it is there for.
>>>>
>>>> The event doesn't help you since only this driver has this issue. So nobody
>>>> will watch this event, unless it is sw specifically written for this SoC.
>>>>
>>>> Much better to call vb2_queue_error to signal a fatal error (which this
>>>> apparently is) since there are more drivers that do this, and vivid supports
>>>> triggering this condition as well.
>>>
>>> So today, I can fiddle around with the IMX219 registers to help gain
>>> an understanding of how this sensor works.  Several of the registers
>>> (such as the PLL setup [*]) require me to disable streaming on the
>>> sensor while changing them.
>>>
>>> This is something I've done many times while testing various ideas,
>>> and is my primary way of figuring out and testing such things.
>>>
>>> Whenever I resume streaming (provided I've let the sensor stop
>>> streaming at a frame boundary) it resumes as if nothing happened.  If I
>>> stop the sensor mid-frame, then I get the rolling issue that Steve
>>> reports, but once the top of the frame becomes aligned with the top of
>>> the capture, everything then becomes stable again as if nothing happened.
>>>
>>> The side effect of what you're proposing is that when I disable streaming
>>> at the sensor by poking at its registers, rather than the capture just
>>> stopping, an error is going to be delivered to gstreamer, and gstreamer
>>> is going to exit, taking the entire capture process down.
>>>
>>> This severely restricts the ability to be able to develop and test
>>> sensor drivers.
>>>
>>> So, I strongly disagree with you.
>>>
>>> Loss of capture frames is not necessarily a fatal error - as I have been
>>> saying repeatedly.  In Steve's case, there's some unknown interaction
>>> between the source and iMX6 hardware that is causing the instability,
>>> but that is simply not true of other sources, and I oppose any idea that
>>> we should cripple the iMX6 side of the capture based upon just one
>>> hardware combination where this is a problem.
>>>
>>> Steve suggested that the problem could be in the iMX6 CSI block - and I
>>> note comparing Steve's code with the code in FSL's repository that there
>>> are some changes that are missing in Steve's code to do with the CCIR656
>>> sync code setup, particularly for >8 bit.  The progressive CCIR656 8-bit
>>> setup looks pretty similar though - but I think what needs to be asked
>>> is whether the same problem is visible using the FSL/NXP vendor kernel.
>>>
>>>
>>> * - the PLL setup is something that requires research at the moment.
>>> Sony's official position (even to their customers) is that they do not
>>> supply the necessary information, instead they expect customers to tell
>>> them the capture settings they want, and Sony will throw the values into
>>> a spreadsheet, and they'll supply the register settings back to the
>>> customer.  Hence, the only way to proceed with a generic driver for
>>> this sensor is to experiment, and experimenting requires the ability to
>>> pause the stream at the sensor while making changes.  Take this away,
>>> and we're stuck with the tables-of-register-settings-for-set-of-fixed-
>>> capture-settings approach.  I've made a lot of progress away from this
>>> which is all down to the flexibility afforded by _not_ killing the
>>> capture process.
>>>
>>
>> In other words: Steve should either find a proper fix for this, or only
>> call vb2_queue_error in this specific case. Sending an event that nobody
>> will know how to handle or what to do with is pretty pointless IMHO.
>>
>> Let's just give him time to try and figure out the real issue here.
> 
> 
> This is a long-standing issue, I've traveled to Hildesheim working with
> our customer to try and get to the bottom of it. I can go into a lot of
> details from those trips, we probed the bt.656 bus with a logic analyzer
> and I can share those results with anyone who asks. But the results of
> those investigations indicate the CSI is not handling the SAV/EAV sync
> codes correctly - if there is a shift in the line position at which
> those codes occur, the CSI/IPU does not abort the frame capture DMA
> and start from the new sync code position, it just continues to capture
> lines until the programmed number of lines are transferred, hence you
> get these split images. Freescale also informed us of a mechanism in the
> IPU that will add lines if it detects these short frames, until the
> programmed number of lines are reached. Apparently that is what creates 
> the rolling effect, but this rolling can last for up to a full minute,
> which is completely unacceptable, it must be corrected as soon as
> possible.
> 
> So the only thing we could come up with was to monitor frame intervals,
> this is purely empirical, but we observed that frame intervals drop
> by approx. one line time (~60 usec) when these short frames are
> received. I don't really have any explanation for that but we take
> advantage of that observation by sending this event to userspace so
> the problem can be corrected immediately with a stream restart.
> 
> As I've said, the ADV718x does not provide _any_ indication via status
> when the shift in the sync code position occurs. And the IPU is also 
> severely lacking in DMA completion status as well (no short packet
> status like in USB for example). So the only way to detect this event
> is by monitoring the frame intervals.
> 
> I will review differences in the CCIR code register setup from FSL's
> repo that Russell pointed out, but I'm fairly sure those code registers
> are setup correctly, there's not much room for variability in those
> values. They only define the values of the sync codes, so the CSI can
> detect them, those values are defined by the bt.656 spec.
> 
> Anyway, perhaps for now I can remove the event, but keep the FI
> monitoring, and for now just report a kernel error message on
> a detected bad FI.

Is it possible to detect this specific situation? Apparently this issue
is not present (or at least resolves itself very quickly) on the imx219.

If it is not possible, then a private event would be acceptable, but
needs to be carefully documented. After all, it is a workaround for a bug,
since otherwise there would be no need for this event.

Regards,

	Hans
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/13/2017 10:10 AM, Hans Verkuil wrote:
> On 03/13/2017 06:06 PM, Steve Longerbeam wrote:
>>
>>
>> On 03/13/2017 03:53 AM, Hans Verkuil wrote:
>>> On 03/13/2017 11:45 AM, Russell King - ARM Linux wrote:
>>>> On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
>>>>> On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
>>>>>> The event must be user visible, otherwise the user has no indication
>>>>>> the error, and can't correct it by stream restart.
>>>>>
>>>>> In that case the driver can detect this and call vb2_queue_error. It's
>>>>> what it is there for.
>>>>>
>>>>> The event doesn't help you since only this driver has this issue. So nobody
>>>>> will watch this event, unless it is sw specifically written for this SoC.
>>>>>
>>>>> Much better to call vb2_queue_error to signal a fatal error (which this
>>>>> apparently is) since there are more drivers that do this, and vivid supports
>>>>> triggering this condition as well.
>>>>
>>>> So today, I can fiddle around with the IMX219 registers to help gain
>>>> an understanding of how this sensor works.  Several of the registers
>>>> (such as the PLL setup [*]) require me to disable streaming on the
>>>> sensor while changing them.
>>>>
>>>> This is something I've done many times while testing various ideas,
>>>> and is my primary way of figuring out and testing such things.
>>>>
>>>> Whenever I resume streaming (provided I've let the sensor stop
>>>> streaming at a frame boundary) it resumes as if nothing happened.  If I
>>>> stop the sensor mid-frame, then I get the rolling issue that Steve
>>>> reports, but once the top of the frame becomes aligned with the top of
>>>> the capture, everything then becomes stable again as if nothing happened.
>>>>
>>>> The side effect of what you're proposing is that when I disable streaming
>>>> at the sensor by poking at its registers, rather than the capture just
>>>> stopping, an error is going to be delivered to gstreamer, and gstreamer
>>>> is going to exit, taking the entire capture process down.
>>>>
>>>> This severely restricts the ability to be able to develop and test
>>>> sensor drivers.
>>>>
>>>> So, I strongly disagree with you.
>>>>
>>>> Loss of capture frames is not necessarily a fatal error - as I have been
>>>> saying repeatedly.  In Steve's case, there's some unknown interaction
>>>> between the source and iMX6 hardware that is causing the instability,
>>>> but that is simply not true of other sources, and I oppose any idea that
>>>> we should cripple the iMX6 side of the capture based upon just one
>>>> hardware combination where this is a problem.
>>>>
>>>> Steve suggested that the problem could be in the iMX6 CSI block - and I
>>>> note comparing Steve's code with the code in FSL's repository that there
>>>> are some changes that are missing in Steve's code to do with the CCIR656
>>>> sync code setup, particularly for >8 bit.  The progressive CCIR656 8-bit
>>>> setup looks pretty similar though - but I think what needs to be asked
>>>> is whether the same problem is visible using the FSL/NXP vendor kernel.
>>>>
>>>>
>>>> * - the PLL setup is something that requires research at the moment.
>>>> Sony's official position (even to their customers) is that they do not
>>>> supply the necessary information, instead they expect customers to tell
>>>> them the capture settings they want, and Sony will throw the values into
>>>> a spreadsheet, and they'll supply the register settings back to the
>>>> customer.  Hence, the only way to proceed with a generic driver for
>>>> this sensor is to experiment, and experimenting requires the ability to
>>>> pause the stream at the sensor while making changes.  Take this away,
>>>> and we're stuck with the tables-of-register-settings-for-set-of-fixed-
>>>> capture-settings approach.  I've made a lot of progress away from this
>>>> which is all down to the flexibility afforded by _not_ killing the
>>>> capture process.
>>>>
>>>
>>> In other words: Steve should either find a proper fix for this, or only
>>> call vb2_queue_error in this specific case. Sending an event that nobody
>>> will know how to handle or what to do with is pretty pointless IMHO.
>>>
>>> Let's just give him time to try and figure out the real issue here.
>>
>>
>> This is a long-standing issue, I've traveled to Hildesheim working with
>> our customer to try and get to the bottom of it. I can go into a lot of
>> details from those trips, we probed the bt.656 bus with a logic analyzer
>> and I can share those results with anyone who asks. But the results of
>> those investigations indicate the CSI is not handling the SAV/EAV sync
>> codes correctly - if there is a shift in the line position at which
>> those codes occur, the CSI/IPU does not abort the frame capture DMA
>> and start from the new sync code position, it just continues to capture
>> lines until the programmed number of lines are transferred, hence you
>> get these split images. Freescale also informed us of a mechanism in the
>> IPU that will add lines if it detects these short frames, until the
>> programmed number of lines are reached. Apparently that is what creates
>> the rolling effect, but this rolling can last for up to a full minute,
>> which is completely unacceptable, it must be corrected as soon as
>> possible.
>>
>> So the only thing we could come up with was to monitor frame intervals,
>> this is purely empirical, but we observed that frame intervals drop
>> by approx. one line time (~60 usec) when these short frames are
>> received. I don't really have any explanation for that but we take
>> advantage of that observation by sending this event to userspace so
>> the problem can be corrected immediately with a stream restart.
>>
>> As I've said, the ADV718x does not provide _any_ indication via status
>> when the shift in the sync code position occurs. And the IPU is also
>> severely lacking in DMA completion status as well (no short packet
>> status like in USB for example). So the only way to detect this event
>> is by monitoring the frame intervals.
>>
>> I will review differences in the CCIR code register setup from FSL's
>> repo that Russell pointed out, but I'm fairly sure those code registers
>> are setup correctly, there's not much room for variability in those
>> values. They only define the values of the sync codes, so the CSI can
>> detect them, those values are defined by the bt.656 spec.
>>
>> Anyway, perhaps for now I can remove the event, but keep the FI
>> monitoring, and for now just report a kernel error message on
>> a detected bad FI.
>
> Is it possible to detect this specific situation? Apparently this issue
> is not present (or at least resolves itself very quickly) on the imx219.

The imx219 is not a BT.656 interface, it is MIPI CSI-2, so this is
not an issue for imx219. It is an issue for any sensor with a
parallel BT.656 interface.

>
> If it is not possible, then a private event would be acceptable, but
> needs to be carefully documented. After all, it is a workaround for a bug,
> since otherwise there would be no need for this event.

Ok, sounds like a plan, I'll keep the event as a private event and make
sure it is documented well. Yes it is a workaround, for a silicon bug,
although Freescale/NXP has not issued an errata for it yet AFAIK. THat
might be because they claim to handle it via this adding lines
mechanism, but that mechanism doesn't work well (long duration rolling),
or not at all (permanent split images).


Steve

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/13/2017 10:10 AM, Hans Verkuil wrote:
> On 03/13/2017 06:06 PM, Steve Longerbeam wrote:
>>
>>
>> On 03/13/2017 03:53 AM, Hans Verkuil wrote:
>>> On 03/13/2017 11:45 AM, Russell King - ARM Linux wrote:
>>>> On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
>>>>> On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
>>>>>> The event must be user visible, otherwise the user has no indication
>>>>>> the error, and can't correct it by stream restart.
>>>>>
>>>>> In that case the driver can detect this and call vb2_queue_error. It's
>>>>> what it is there for.
>>>>>
>>>>> The event doesn't help you since only this driver has this issue. So nobody
>>>>> will watch this event, unless it is sw specifically written for this SoC.
>>>>>
>>>>> Much better to call vb2_queue_error to signal a fatal error (which this
>>>>> apparently is) since there are more drivers that do this, and vivid supports
>>>>> triggering this condition as well.
>>>>
>>>> So today, I can fiddle around with the IMX219 registers to help gain
>>>> an understanding of how this sensor works.  Several of the registers
>>>> (such as the PLL setup [*]) require me to disable streaming on the
>>>> sensor while changing them.
>>>>
>>>> This is something I've done many times while testing various ideas,
>>>> and is my primary way of figuring out and testing such things.
>>>>
>>>> Whenever I resume streaming (provided I've let the sensor stop
>>>> streaming at a frame boundary) it resumes as if nothing happened.  If I
>>>> stop the sensor mid-frame, then I get the rolling issue that Steve
>>>> reports, but once the top of the frame becomes aligned with the top of
>>>> the capture, everything then becomes stable again as if nothing happened.
>>>>
>>>> The side effect of what you're proposing is that when I disable streaming
>>>> at the sensor by poking at its registers, rather than the capture just
>>>> stopping, an error is going to be delivered to gstreamer, and gstreamer
>>>> is going to exit, taking the entire capture process down.
>>>>
>>>> This severely restricts the ability to be able to develop and test
>>>> sensor drivers.
>>>>
>>>> So, I strongly disagree with you.
>>>>
>>>> Loss of capture frames is not necessarily a fatal error - as I have been
>>>> saying repeatedly.  In Steve's case, there's some unknown interaction
>>>> between the source and iMX6 hardware that is causing the instability,
>>>> but that is simply not true of other sources, and I oppose any idea that
>>>> we should cripple the iMX6 side of the capture based upon just one
>>>> hardware combination where this is a problem.
>>>>
>>>> Steve suggested that the problem could be in the iMX6 CSI block - and I
>>>> note comparing Steve's code with the code in FSL's repository that there
>>>> are some changes that are missing in Steve's code to do with the CCIR656
>>>> sync code setup, particularly for >8 bit.  The progressive CCIR656 8-bit
>>>> setup looks pretty similar though - but I think what needs to be asked
>>>> is whether the same problem is visible using the FSL/NXP vendor kernel.
>>>>
>>>>
>>>> * - the PLL setup is something that requires research at the moment.
>>>> Sony's official position (even to their customers) is that they do not
>>>> supply the necessary information, instead they expect customers to tell
>>>> them the capture settings they want, and Sony will throw the values into
>>>> a spreadsheet, and they'll supply the register settings back to the
>>>> customer.  Hence, the only way to proceed with a generic driver for
>>>> this sensor is to experiment, and experimenting requires the ability to
>>>> pause the stream at the sensor while making changes.  Take this away,
>>>> and we're stuck with the tables-of-register-settings-for-set-of-fixed-
>>>> capture-settings approach.  I've made a lot of progress away from this
>>>> which is all down to the flexibility afforded by _not_ killing the
>>>> capture process.
>>>>
>>>
>>> In other words: Steve should either find a proper fix for this, or only
>>> call vb2_queue_error in this specific case. Sending an event that nobody
>>> will know how to handle or what to do with is pretty pointless IMHO.
>>>
>>> Let's just give him time to try and figure out the real issue here.
>>
>>
>> This is a long-standing issue, I've traveled to Hildesheim working with
>> our customer to try and get to the bottom of it. I can go into a lot of
>> details from those trips, we probed the bt.656 bus with a logic analyzer
>> and I can share those results with anyone who asks. But the results of
>> those investigations indicate the CSI is not handling the SAV/EAV sync
>> codes correctly - if there is a shift in the line position at which
>> those codes occur, the CSI/IPU does not abort the frame capture DMA
>> and start from the new sync code position, it just continues to capture
>> lines until the programmed number of lines are transferred, hence you
>> get these split images. Freescale also informed us of a mechanism in the
>> IPU that will add lines if it detects these short frames, until the
>> programmed number of lines are reached. Apparently that is what creates
>> the rolling effect, but this rolling can last for up to a full minute,
>> which is completely unacceptable, it must be corrected as soon as
>> possible.
>>
>> So the only thing we could come up with was to monitor frame intervals,
>> this is purely empirical, but we observed that frame intervals drop
>> by approx. one line time (~60 usec) when these short frames are
>> received. I don't really have any explanation for that but we take
>> advantage of that observation by sending this event to userspace so
>> the problem can be corrected immediately with a stream restart.
>>
>> As I've said, the ADV718x does not provide _any_ indication via status
>> when the shift in the sync code position occurs. And the IPU is also
>> severely lacking in DMA completion status as well (no short packet
>> status like in USB for example). So the only way to detect this event
>> is by monitoring the frame intervals.
>>
>> I will review differences in the CCIR code register setup from FSL's
>> repo that Russell pointed out, but I'm fairly sure those code registers
>> are setup correctly, there's not much room for variability in those
>> values. They only define the values of the sync codes, so the CSI can
>> detect them, those values are defined by the bt.656 spec.
>>
>> Anyway, perhaps for now I can remove the event, but keep the FI
>> monitoring, and for now just report a kernel error message on
>> a detected bad FI.
>
> Is it possible to detect this specific situation? Apparently this issue
> is not present (or at least resolves itself very quickly) on the imx219.

The imx219 is not a BT.656 interface, it is MIPI CSI-2, so this is
not an issue for imx219. It is an issue for any sensor with a
parallel BT.656 interface.

>
> If it is not possible, then a private event would be acceptable, but
> needs to be carefully documented. After all, it is a workaround for a bug,
> since otherwise there would be no need for this event.

Ok, sounds like a plan, I'll keep the event as a private event and make
sure it is documented well. Yes it is a workaround, for a silicon bug,
although Freescale/NXP has not issued an errata for it yet AFAIK. THat
might be because they claim to handle it via this adding lines
mechanism, but that mechanism doesn't work well (long duration rolling),
or not at all (permanent split images).


Steve

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/13/2017 10:10 AM, Hans Verkuil wrote:
> On 03/13/2017 06:06 PM, Steve Longerbeam wrote:
>>
>>
>> On 03/13/2017 03:53 AM, Hans Verkuil wrote:
>>> On 03/13/2017 11:45 AM, Russell King - ARM Linux wrote:
>>>> On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
>>>>> On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
>>>>>> The event must be user visible, otherwise the user has no indication
>>>>>> the error, and can't correct it by stream restart.
>>>>>
>>>>> In that case the driver can detect this and call vb2_queue_error. It's
>>>>> what it is there for.
>>>>>
>>>>> The event doesn't help you since only this driver has this issue. So nobody
>>>>> will watch this event, unless it is sw specifically written for this SoC.
>>>>>
>>>>> Much better to call vb2_queue_error to signal a fatal error (which this
>>>>> apparently is) since there are more drivers that do this, and vivid supports
>>>>> triggering this condition as well.
>>>>
>>>> So today, I can fiddle around with the IMX219 registers to help gain
>>>> an understanding of how this sensor works.  Several of the registers
>>>> (such as the PLL setup [*]) require me to disable streaming on the
>>>> sensor while changing them.
>>>>
>>>> This is something I've done many times while testing various ideas,
>>>> and is my primary way of figuring out and testing such things.
>>>>
>>>> Whenever I resume streaming (provided I've let the sensor stop
>>>> streaming at a frame boundary) it resumes as if nothing happened.  If I
>>>> stop the sensor mid-frame, then I get the rolling issue that Steve
>>>> reports, but once the top of the frame becomes aligned with the top of
>>>> the capture, everything then becomes stable again as if nothing happened.
>>>>
>>>> The side effect of what you're proposing is that when I disable streaming
>>>> at the sensor by poking at its registers, rather than the capture just
>>>> stopping, an error is going to be delivered to gstreamer, and gstreamer
>>>> is going to exit, taking the entire capture process down.
>>>>
>>>> This severely restricts the ability to be able to develop and test
>>>> sensor drivers.
>>>>
>>>> So, I strongly disagree with you.
>>>>
>>>> Loss of capture frames is not necessarily a fatal error - as I have been
>>>> saying repeatedly.  In Steve's case, there's some unknown interaction
>>>> between the source and iMX6 hardware that is causing the instability,
>>>> but that is simply not true of other sources, and I oppose any idea that
>>>> we should cripple the iMX6 side of the capture based upon just one
>>>> hardware combination where this is a problem.
>>>>
>>>> Steve suggested that the problem could be in the iMX6 CSI block - and I
>>>> note comparing Steve's code with the code in FSL's repository that there
>>>> are some changes that are missing in Steve's code to do with the CCIR656
>>>> sync code setup, particularly for >8 bit.  The progressive CCIR656 8-bit
>>>> setup looks pretty similar though - but I think what needs to be asked
>>>> is whether the same problem is visible using the FSL/NXP vendor kernel.
>>>>
>>>>
>>>> * - the PLL setup is something that requires research at the moment.
>>>> Sony's official position (even to their customers) is that they do not
>>>> supply the necessary information, instead they expect customers to tell
>>>> them the capture settings they want, and Sony will throw the values into
>>>> a spreadsheet, and they'll supply the register settings back to the
>>>> customer.  Hence, the only way to proceed with a generic driver for
>>>> this sensor is to experiment, and experimenting requires the ability to
>>>> pause the stream at the sensor while making changes.  Take this away,
>>>> and we're stuck with the tables-of-register-settings-for-set-of-fixed-
>>>> capture-settings approach.  I've made a lot of progress away from this
>>>> which is all down to the flexibility afforded by _not_ killing the
>>>> capture process.
>>>>
>>>
>>> In other words: Steve should either find a proper fix for this, or only
>>> call vb2_queue_error in this specific case. Sending an event that nobody
>>> will know how to handle or what to do with is pretty pointless IMHO.
>>>
>>> Let's just give him time to try and figure out the real issue here.
>>
>>
>> This is a long-standing issue, I've traveled to Hildesheim working with
>> our customer to try and get to the bottom of it. I can go into a lot of
>> details from those trips, we probed the bt.656 bus with a logic analyzer
>> and I can share those results with anyone who asks. But the results of
>> those investigations indicate the CSI is not handling the SAV/EAV sync
>> codes correctly - if there is a shift in the line position at which
>> those codes occur, the CSI/IPU does not abort the frame capture DMA
>> and start from the new sync code position, it just continues to capture
>> lines until the programmed number of lines are transferred, hence you
>> get these split images. Freescale also informed us of a mechanism in the
>> IPU that will add lines if it detects these short frames, until the
>> programmed number of lines are reached. Apparently that is what creates
>> the rolling effect, but this rolling can last for up to a full minute,
>> which is completely unacceptable, it must be corrected as soon as
>> possible.
>>
>> So the only thing we could come up with was to monitor frame intervals,
>> this is purely empirical, but we observed that frame intervals drop
>> by approx. one line time (~60 usec) when these short frames are
>> received. I don't really have any explanation for that but we take
>> advantage of that observation by sending this event to userspace so
>> the problem can be corrected immediately with a stream restart.
>>
>> As I've said, the ADV718x does not provide _any_ indication via status
>> when the shift in the sync code position occurs. And the IPU is also
>> severely lacking in DMA completion status as well (no short packet
>> status like in USB for example). So the only way to detect this event
>> is by monitoring the frame intervals.
>>
>> I will review differences in the CCIR code register setup from FSL's
>> repo that Russell pointed out, but I'm fairly sure those code registers
>> are setup correctly, there's not much room for variability in those
>> values. They only define the values of the sync codes, so the CSI can
>> detect them, those values are defined by the bt.656 spec.
>>
>> Anyway, perhaps for now I can remove the event, but keep the FI
>> monitoring, and for now just report a kernel error message on
>> a detected bad FI.
>
> Is it possible to detect this specific situation? Apparently this issue
> is not present (or at least resolves itself very quickly) on the imx219.

The imx219 is not a BT.656 interface, it is MIPI CSI-2, so this is
not an issue for imx219. It is an issue for any sensor with a
parallel BT.656 interface.

>
> If it is not possible, then a private event would be acceptable, but
> needs to be carefully documented. After all, it is a workaround for a bug,
> since otherwise there would be no need for this event.

Ok, sounds like a plan, I'll keep the event as a private event and make
sure it is documented well. Yes it is a workaround, for a silicon bug,
although Freescale/NXP has not issued an errata for it yet AFAIK. THat
might be because they claim to handle it via this adding lines
mechanism, but that mechanism doesn't work well (long duration rolling),
or not at all (permanent split images).


Steve

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Nicolas Dufresne]

[-- Attachment #1: Type: text/plain, Size: 4714 bytes --]

Le lundi 13 mars 2017 à 10:45 +0000, Russell King - ARM Linux a écrit :
> On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
> > On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
> > > The event must be user visible, otherwise the user has no indication
> > > the error, and can't correct it by stream restart.
> > 
> > In that case the driver can detect this and call vb2_queue_error. It's
> > what it is there for.
> > 
> > The event doesn't help you since only this driver has this issue. So nobody
> > will watch this event, unless it is sw specifically written for this SoC.
> > 
> > Much better to call vb2_queue_error to signal a fatal error (which this
> > apparently is) since there are more drivers that do this, and vivid supports
> > triggering this condition as well.
> 
> So today, I can fiddle around with the IMX219 registers to help gain
> an understanding of how this sensor works.  Several of the registers
> (such as the PLL setup [*]) require me to disable streaming on the
> sensor while changing them.
> 
> This is something I've done many times while testing various ideas,
> and is my primary way of figuring out and testing such things.
> 
> Whenever I resume streaming (provided I've let the sensor stop
> streaming at a frame boundary) it resumes as if nothing happened.  If I
> stop the sensor mid-frame, then I get the rolling issue that Steve
> reports, but once the top of the frame becomes aligned with the top of
> the capture, everything then becomes stable again as if nothing happened.
> 
> The side effect of what you're proposing is that when I disable streaming
> at the sensor by poking at its registers, rather than the capture just
> stopping, an error is going to be delivered to gstreamer, and gstreamer
> is going to exit, taking the entire capture process down.

Indeed, there is no recovery attempt in GStreamer code, and it's hard
for an higher level programs to handle this. Nothing prevents from
adding something of course, but the errors are really un-specific, so
it would be something pretty blind. For what it has been tested, this
case was never met, usually the error is triggered by a USB camera
being un-plugged, a driver failure or even a firmware crash. Most of
the time, this is not recoverable.

My main concern here based on what I'm reading, is that this driver is
not even able to notice immediately that a produced frame was corrupted
(because it's out of sync). From usability perspective, this is really
bad. Can't the driver derive a clock from some irq and calculate for
each frame if the timing was correct ? And if not mark the buffer with
V4L2_BUF_FLAG_ERROR ?

> 
> This severely restricts the ability to be able to develop and test
> sensor drivers.
> 
> So, I strongly disagree with you.
> 
> Loss of capture frames is not necessarily a fatal error - as I have been
> saying repeatedly.  In Steve's case, there's some unknown interaction
> between the source and iMX6 hardware that is causing the instability,
> but that is simply not true of other sources, and I oppose any idea that
> we should cripple the iMX6 side of the capture based upon just one
> hardware combination where this is a problem.

Indeed, it happens all the time with slow USB port and UVC devices.
Though, the driver is well aware, and mark the buffers with
V4L2_BUF_FLAG_ERROR.

> 
> Steve suggested that the problem could be in the iMX6 CSI block - and I
> note comparing Steve's code with the code in FSL's repository that there
> are some changes that are missing in Steve's code to do with the CCIR656
> sync code setup, particularly for >8 bit.  The progressive CCIR656 8-bit
> setup looks pretty similar though - but I think what needs to be asked
> is whether the same problem is visible using the FSL/NXP vendor kernel.
> 
> 
> * - the PLL setup is something that requires research at the moment.
> Sony's official position (even to their customers) is that they do not
> supply the necessary information, instead they expect customers to tell
> them the capture settings they want, and Sony will throw the values into
> a spreadsheet, and they'll supply the register settings back to the
> customer.  Hence, the only way to proceed with a generic driver for
> this sensor is to experiment, and experimenting requires the ability to
> pause the stream at the sensor while making changes.  Take this away,
> and we're stuck with the tables-of-register-settings-for-set-of-fixed-
> capture-settings approach.  I've made a lot of progress away from this
> which is all down to the flexibility afforded by _not_ killing the
> capture process.
> 

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Nicolas Dufresne]

Le lundi 13 mars 2017 ? 10:45 +0000, Russell King - ARM Linux a ?crit?:
> On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
> > On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
> > > The event must be user visible, otherwise the user has no indication
> > > the error, and can't correct it by stream restart.
> > 
> > In that case the driver can detect this and call vb2_queue_error. It's
> > what it is there for.
> > 
> > The event doesn't help you since only this driver has this issue. So nobody
> > will watch this event, unless it is sw specifically written for this SoC.
> > 
> > Much better to call vb2_queue_error to signal a fatal error (which this
> > apparently is) since there are more drivers that do this, and vivid supports
> > triggering this condition as well.
> 
> So today, I can fiddle around with the IMX219 registers to help gain
> an understanding of how this sensor works.??Several of the registers
> (such as the PLL setup [*]) require me to disable streaming on the
> sensor while changing them.
> 
> This is something I've done many times while testing various ideas,
> and is my primary way of figuring out and testing such things.
> 
> Whenever I resume streaming (provided I've let the sensor stop
> streaming at a frame boundary) it resumes as if nothing happened.??If I
> stop the sensor mid-frame, then I get the rolling issue that Steve
> reports, but once the top of the frame becomes aligned with the top of
> the capture, everything then becomes stable again as if nothing happened.
> 
> The side effect of what you're proposing is that when I disable streaming
> at the sensor by poking at its registers, rather than the capture just
> stopping, an error is going to be delivered to gstreamer, and gstreamer
> is going to exit, taking the entire capture process down.

Indeed, there is no recovery attempt in GStreamer code, and it's hard
for an higher level programs to handle this. Nothing prevents from
adding something of course, but the errors are really un-specific, so
it would be something pretty blind. For what it has been tested, this
case was never met, usually the error is triggered by a USB camera
being un-plugged, a driver failure or even a firmware crash. Most of
the time, this is not recoverable.

My main concern here based on what I'm reading, is that this driver is
not even able to notice immediately that a produced frame was corrupted
(because it's out of sync). From usability perspective, this is really
bad. Can't the driver derive a clock from some irq and calculate for
each frame if the timing was correct ? And if not mark the buffer with
V4L2_BUF_FLAG_ERROR ?

> 
> This severely restricts the ability to be able to develop and test
> sensor drivers.
> 
> So, I strongly disagree with you.
> 
> Loss of capture frames is not necessarily a fatal error - as I have been
> saying repeatedly.??In Steve's case, there's some unknown interaction
> between the source and iMX6 hardware that is causing the instability,
> but that is simply not true of other sources, and I oppose any idea that
> we should cripple the iMX6 side of the capture based upon just one
> hardware combination where this is a problem.

Indeed, it happens all the time with slow USB port and UVC devices.
Though, the driver is well aware, and mark the buffers with
V4L2_BUF_FLAG_ERROR.

> 
> Steve suggested that the problem could be in the iMX6 CSI block - and I
> note comparing Steve's code with the code in FSL's repository that there
> are some changes that are missing in Steve's code to do with the CCIR656
> sync code setup, particularly for >8 bit.??The progressive CCIR656 8-bit
> setup looks pretty similar though - but I think what needs to be asked
> is whether the same problem is visible using the FSL/NXP vendor kernel.
> 
> 
> * - the PLL setup is something that requires research at the moment.
> Sony's official position (even to their customers) is that they do not
> supply the necessary information, instead they expect customers to tell
> them the capture settings they want, and Sony will throw the values into
> a spreadsheet, and they'll supply the register settings back to the
> customer.??Hence, the only way to proceed with a generic driver for
> this sensor is to experiment, and experimenting requires the ability to
> pause the stream at the sensor while making changes.??Take this away,
> and we're stuck with the tables-of-register-settings-for-set-of-fixed-
> capture-settings approach.??I've made a lot of progress away from this
> which is all down to the flexibility afforded by _not_ killing the
> capture process.
> 
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 181 bytes
Desc: This is a digitally signed message part
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170314/4ab6983e/attachment-0001.sig>

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Nicolas Dufresne]

[-- Attachment #1: Type: text/plain, Size: 4714 bytes --]

Le lundi 13 mars 2017 à 10:45 +0000, Russell King - ARM Linux a écrit :
> On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
> > On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
> > > The event must be user visible, otherwise the user has no indication
> > > the error, and can't correct it by stream restart.
> > 
> > In that case the driver can detect this and call vb2_queue_error. It's
> > what it is there for.
> > 
> > The event doesn't help you since only this driver has this issue. So nobody
> > will watch this event, unless it is sw specifically written for this SoC.
> > 
> > Much better to call vb2_queue_error to signal a fatal error (which this
> > apparently is) since there are more drivers that do this, and vivid supports
> > triggering this condition as well.
> 
> So today, I can fiddle around with the IMX219 registers to help gain
> an understanding of how this sensor works.  Several of the registers
> (such as the PLL setup [*]) require me to disable streaming on the
> sensor while changing them.
> 
> This is something I've done many times while testing various ideas,
> and is my primary way of figuring out and testing such things.
> 
> Whenever I resume streaming (provided I've let the sensor stop
> streaming at a frame boundary) it resumes as if nothing happened.  If I
> stop the sensor mid-frame, then I get the rolling issue that Steve
> reports, but once the top of the frame becomes aligned with the top of
> the capture, everything then becomes stable again as if nothing happened.
> 
> The side effect of what you're proposing is that when I disable streaming
> at the sensor by poking at its registers, rather than the capture just
> stopping, an error is going to be delivered to gstreamer, and gstreamer
> is going to exit, taking the entire capture process down.

Indeed, there is no recovery attempt in GStreamer code, and it's hard
for an higher level programs to handle this. Nothing prevents from
adding something of course, but the errors are really un-specific, so
it would be something pretty blind. For what it has been tested, this
case was never met, usually the error is triggered by a USB camera
being un-plugged, a driver failure or even a firmware crash. Most of
the time, this is not recoverable.

My main concern here based on what I'm reading, is that this driver is
not even able to notice immediately that a produced frame was corrupted
(because it's out of sync). From usability perspective, this is really
bad. Can't the driver derive a clock from some irq and calculate for
each frame if the timing was correct ? And if not mark the buffer with
V4L2_BUF_FLAG_ERROR ?

> 
> This severely restricts the ability to be able to develop and test
> sensor drivers.
> 
> So, I strongly disagree with you.
> 
> Loss of capture frames is not necessarily a fatal error - as I have been
> saying repeatedly.  In Steve's case, there's some unknown interaction
> between the source and iMX6 hardware that is causing the instability,
> but that is simply not true of other sources, and I oppose any idea that
> we should cripple the iMX6 side of the capture based upon just one
> hardware combination where this is a problem.

Indeed, it happens all the time with slow USB port and UVC devices.
Though, the driver is well aware, and mark the buffers with
V4L2_BUF_FLAG_ERROR.

> 
> Steve suggested that the problem could be in the iMX6 CSI block - and I
> note comparing Steve's code with the code in FSL's repository that there
> are some changes that are missing in Steve's code to do with the CCIR656
> sync code setup, particularly for >8 bit.  The progressive CCIR656 8-bit
> setup looks pretty similar though - but I think what needs to be asked
> is whether the same problem is visible using the FSL/NXP vendor kernel.
> 
> 
> * - the PLL setup is something that requires research at the moment.
> Sony's official position (even to their customers) is that they do not
> supply the necessary information, instead they expect customers to tell
> them the capture settings they want, and Sony will throw the values into
> a spreadsheet, and they'll supply the register settings back to the
> customer.  Hence, the only way to proceed with a generic driver for
> this sensor is to experiment, and experimenting requires the ability to
> pause the stream at the sensor while making changes.  Take this away,
> and we're stuck with the tables-of-register-settings-for-set-of-fixed-
> capture-settings approach.  I've made a lot of progress away from this
> which is all down to the flexibility afforded by _not_ killing the
> capture process.
> 

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/14/2017 09:21 AM, Nicolas Dufresne wrote:
> Le lundi 13 mars 2017 à 10:45 +0000, Russell King - ARM Linux a écrit :
>> On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
>>> On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
>>>> The event must be user visible, otherwise the user has no indication
>>>> the error, and can't correct it by stream restart.
>>> In that case the driver can detect this and call vb2_queue_error. It's
>>> what it is there for.
>>>
>>> The event doesn't help you since only this driver has this issue. So nobody
>>> will watch this event, unless it is sw specifically written for this SoC.
>>>
>>> Much better to call vb2_queue_error to signal a fatal error (which this
>>> apparently is) since there are more drivers that do this, and vivid supports
>>> triggering this condition as well.
>> So today, I can fiddle around with the IMX219 registers to help gain
>> an understanding of how this sensor works.  Several of the registers
>> (such as the PLL setup [*]) require me to disable streaming on the
>> sensor while changing them.
>>
>> This is something I've done many times while testing various ideas,
>> and is my primary way of figuring out and testing such things.
>>
>> Whenever I resume streaming (provided I've let the sensor stop
>> streaming at a frame boundary) it resumes as if nothing happened.  If I
>> stop the sensor mid-frame, then I get the rolling issue that Steve
>> reports, but once the top of the frame becomes aligned with the top of
>> the capture, everything then becomes stable again as if nothing happened.
>>
>> The side effect of what you're proposing is that when I disable streaming
>> at the sensor by poking at its registers, rather than the capture just
>> stopping, an error is going to be delivered to gstreamer, and gstreamer
>> is going to exit, taking the entire capture process down.
> Indeed, there is no recovery attempt in GStreamer code, and it's hard
> for an higher level programs to handle this. Nothing prevents from
> adding something of course, but the errors are really un-specific, so
> it would be something pretty blind. For what it has been tested, this
> case was never met, usually the error is triggered by a USB camera
> being un-plugged, a driver failure or even a firmware crash. Most of
> the time, this is not recoverable.
>
> My main concern here based on what I'm reading, is that this driver is
> not even able to notice immediately that a produced frame was corrupted
> (because it's out of sync). From usability perspective, this is really
> bad.

First, this is an isolated problem, specific to bt.656 and it only
occurs when disrupting the analog video source signal in some
way (by unplugging the RCA cable from the ADV718x connector
for example).

Second, there is no DMA status support in i.MX6 to catch these
shifted bt.656 codes, and the ADV718x does not provide any
status indicators of this event either. So monitoring frame intervals
is the only solution available, until FSL/NXP issues a new silicon rev.


>   Can't the driver derive a clock from some irq and calculate for
> each frame if the timing was correct ?

That's what is being done, essentially.

>   And if not mark the buffer with
> V4L2_BUF_FLAG_ERROR ?

I prefer to keep the private event, V4L2_BUF_FLAG_ERROR is too
unspecific.

Steve


>
>> This severely restricts the ability to be able to develop and test
>> sensor drivers.
>>
>> So, I strongly disagree with you.
>>
>> Loss of capture frames is not necessarily a fatal error - as I have been
>> saying repeatedly.  In Steve's case, there's some unknown interaction
>> between the source and iMX6 hardware that is causing the instability,
>> but that is simply not true of other sources, and I oppose any idea that
>> we should cripple the iMX6 side of the capture based upon just one
>> hardware combination where this is a problem.
> Indeed, it happens all the time with slow USB port and UVC devices.
> Though, the driver is well aware, and mark the buffers with
> V4L2_BUF_FLAG_ERROR.
>
>> Steve suggested that the problem could be in the iMX6 CSI block - and I
>> note comparing Steve's code with the code in FSL's repository that there
>> are some changes that are missing in Steve's code to do with the CCIR656
>> sync code setup, particularly for >8 bit.  The progressive CCIR656 8-bit
>> setup looks pretty similar though - but I think what needs to be asked
>> is whether the same problem is visible using the FSL/NXP vendor kernel.
>>
>>
>> * - the PLL setup is something that requires research at the moment.
>> Sony's official position (even to their customers) is that they do not
>> supply the necessary information, instead they expect customers to tell
>> them the capture settings they want, and Sony will throw the values into
>> a spreadsheet, and they'll supply the register settings back to the
>> customer.  Hence, the only way to proceed with a generic driver for
>> this sensor is to experiment, and experimenting requires the ability to
>> pause the stream at the sensor while making changes.  Take this away,
>> and we're stuck with the tables-of-register-settings-for-set-of-fixed-
>> capture-settings approach.  I've made a lot of progress away from this
>> which is all down to the flexibility afforded by _not_ killing the
>> capture process.

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/14/2017 09:21 AM, Nicolas Dufresne wrote:
> Le lundi 13 mars 2017 ? 10:45 +0000, Russell King - ARM Linux a ?crit :
>> On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
>>> On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
>>>> The event must be user visible, otherwise the user has no indication
>>>> the error, and can't correct it by stream restart.
>>> In that case the driver can detect this and call vb2_queue_error. It's
>>> what it is there for.
>>>
>>> The event doesn't help you since only this driver has this issue. So nobody
>>> will watch this event, unless it is sw specifically written for this SoC.
>>>
>>> Much better to call vb2_queue_error to signal a fatal error (which this
>>> apparently is) since there are more drivers that do this, and vivid supports
>>> triggering this condition as well.
>> So today, I can fiddle around with the IMX219 registers to help gain
>> an understanding of how this sensor works.  Several of the registers
>> (such as the PLL setup [*]) require me to disable streaming on the
>> sensor while changing them.
>>
>> This is something I've done many times while testing various ideas,
>> and is my primary way of figuring out and testing such things.
>>
>> Whenever I resume streaming (provided I've let the sensor stop
>> streaming at a frame boundary) it resumes as if nothing happened.  If I
>> stop the sensor mid-frame, then I get the rolling issue that Steve
>> reports, but once the top of the frame becomes aligned with the top of
>> the capture, everything then becomes stable again as if nothing happened.
>>
>> The side effect of what you're proposing is that when I disable streaming
>> at the sensor by poking at its registers, rather than the capture just
>> stopping, an error is going to be delivered to gstreamer, and gstreamer
>> is going to exit, taking the entire capture process down.
> Indeed, there is no recovery attempt in GStreamer code, and it's hard
> for an higher level programs to handle this. Nothing prevents from
> adding something of course, but the errors are really un-specific, so
> it would be something pretty blind. For what it has been tested, this
> case was never met, usually the error is triggered by a USB camera
> being un-plugged, a driver failure or even a firmware crash. Most of
> the time, this is not recoverable.
>
> My main concern here based on what I'm reading, is that this driver is
> not even able to notice immediately that a produced frame was corrupted
> (because it's out of sync). From usability perspective, this is really
> bad.

First, this is an isolated problem, specific to bt.656 and it only
occurs when disrupting the analog video source signal in some
way (by unplugging the RCA cable from the ADV718x connector
for example).

Second, there is no DMA status support in i.MX6 to catch these
shifted bt.656 codes, and the ADV718x does not provide any
status indicators of this event either. So monitoring frame intervals
is the only solution available, until FSL/NXP issues a new silicon rev.


>   Can't the driver derive a clock from some irq and calculate for
> each frame if the timing was correct ?

That's what is being done, essentially.

>   And if not mark the buffer with
> V4L2_BUF_FLAG_ERROR ?

I prefer to keep the private event, V4L2_BUF_FLAG_ERROR is too
unspecific.

Steve


>
>> This severely restricts the ability to be able to develop and test
>> sensor drivers.
>>
>> So, I strongly disagree with you.
>>
>> Loss of capture frames is not necessarily a fatal error - as I have been
>> saying repeatedly.  In Steve's case, there's some unknown interaction
>> between the source and iMX6 hardware that is causing the instability,
>> but that is simply not true of other sources, and I oppose any idea that
>> we should cripple the iMX6 side of the capture based upon just one
>> hardware combination where this is a problem.
> Indeed, it happens all the time with slow USB port and UVC devices.
> Though, the driver is well aware, and mark the buffers with
> V4L2_BUF_FLAG_ERROR.
>
>> Steve suggested that the problem could be in the iMX6 CSI block - and I
>> note comparing Steve's code with the code in FSL's repository that there
>> are some changes that are missing in Steve's code to do with the CCIR656
>> sync code setup, particularly for >8 bit.  The progressive CCIR656 8-bit
>> setup looks pretty similar though - but I think what needs to be asked
>> is whether the same problem is visible using the FSL/NXP vendor kernel.
>>
>>
>> * - the PLL setup is something that requires research at the moment.
>> Sony's official position (even to their customers) is that they do not
>> supply the necessary information, instead they expect customers to tell
>> them the capture settings they want, and Sony will throw the values into
>> a spreadsheet, and they'll supply the register settings back to the
>> customer.  Hence, the only way to proceed with a generic driver for
>> this sensor is to experiment, and experimenting requires the ability to
>> pause the stream at the sensor while making changes.  Take this away,
>> and we're stuck with the tables-of-register-settings-for-set-of-fixed-
>> capture-settings approach.  I've made a lot of progress away from this
>> which is all down to the flexibility afforded by _not_ killing the
>> capture process.

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/14/2017 09:21 AM, Nicolas Dufresne wrote:
> Le lundi 13 mars 2017 à 10:45 +0000, Russell King - ARM Linux a écrit :
>> On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
>>> On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
>>>> The event must be user visible, otherwise the user has no indication
>>>> the error, and can't correct it by stream restart.
>>> In that case the driver can detect this and call vb2_queue_error. It's
>>> what it is there for.
>>>
>>> The event doesn't help you since only this driver has this issue. So nobody
>>> will watch this event, unless it is sw specifically written for this SoC.
>>>
>>> Much better to call vb2_queue_error to signal a fatal error (which this
>>> apparently is) since there are more drivers that do this, and vivid supports
>>> triggering this condition as well.
>> So today, I can fiddle around with the IMX219 registers to help gain
>> an understanding of how this sensor works.  Several of the registers
>> (such as the PLL setup [*]) require me to disable streaming on the
>> sensor while changing them.
>>
>> This is something I've done many times while testing various ideas,
>> and is my primary way of figuring out and testing such things.
>>
>> Whenever I resume streaming (provided I've let the sensor stop
>> streaming at a frame boundary) it resumes as if nothing happened.  If I
>> stop the sensor mid-frame, then I get the rolling issue that Steve
>> reports, but once the top of the frame becomes aligned with the top of
>> the capture, everything then becomes stable again as if nothing happened.
>>
>> The side effect of what you're proposing is that when I disable streaming
>> at the sensor by poking at its registers, rather than the capture just
>> stopping, an error is going to be delivered to gstreamer, and gstreamer
>> is going to exit, taking the entire capture process down.
> Indeed, there is no recovery attempt in GStreamer code, and it's hard
> for an higher level programs to handle this. Nothing prevents from
> adding something of course, but the errors are really un-specific, so
> it would be something pretty blind. For what it has been tested, this
> case was never met, usually the error is triggered by a USB camera
> being un-plugged, a driver failure or even a firmware crash. Most of
> the time, this is not recoverable.
>
> My main concern here based on what I'm reading, is that this driver is
> not even able to notice immediately that a produced frame was corrupted
> (because it's out of sync). From usability perspective, this is really
> bad.

First, this is an isolated problem, specific to bt.656 and it only
occurs when disrupting the analog video source signal in some
way (by unplugging the RCA cable from the ADV718x connector
for example).

Second, there is no DMA status support in i.MX6 to catch these
shifted bt.656 codes, and the ADV718x does not provide any
status indicators of this event either. So monitoring frame intervals
is the only solution available, until FSL/NXP issues a new silicon rev.


>   Can't the driver derive a clock from some irq and calculate for
> each frame if the timing was correct ?

That's what is being done, essentially.

>   And if not mark the buffer with
> V4L2_BUF_FLAG_ERROR ?

I prefer to keep the private event, V4L2_BUF_FLAG_ERROR is too
unspecific.

Steve


>
>> This severely restricts the ability to be able to develop and test
>> sensor drivers.
>>
>> So, I strongly disagree with you.
>>
>> Loss of capture frames is not necessarily a fatal error - as I have been
>> saying repeatedly.  In Steve's case, there's some unknown interaction
>> between the source and iMX6 hardware that is causing the instability,
>> but that is simply not true of other sources, and I oppose any idea that
>> we should cripple the iMX6 side of the capture based upon just one
>> hardware combination where this is a problem.
> Indeed, it happens all the time with slow USB port and UVC devices.
> Though, the driver is well aware, and mark the buffers with
> V4L2_BUF_FLAG_ERROR.
>
>> Steve suggested that the problem could be in the iMX6 CSI block - and I
>> note comparing Steve's code with the code in FSL's repository that there
>> are some changes that are missing in Steve's code to do with the CCIR656
>> sync code setup, particularly for >8 bit.  The progressive CCIR656 8-bit
>> setup looks pretty similar though - but I think what needs to be asked
>> is whether the same problem is visible using the FSL/NXP vendor kernel.
>>
>>
>> * - the PLL setup is something that requires research at the moment.
>> Sony's official position (even to their customers) is that they do not
>> supply the necessary information, instead they expect customers to tell
>> them the capture settings they want, and Sony will throw the values into
>> a spreadsheet, and they'll supply the register settings back to the
>> customer.  Hence, the only way to proceed with a generic driver for
>> this sensor is to experiment, and experimenting requires the ability to
>> pause the stream at the sensor while making changes.  Take this away,
>> and we're stuck with the tables-of-register-settings-for-set-of-fixed-
>> capture-settings approach.  I've made a lot of progress away from this
>> which is all down to the flexibility afforded by _not_ killing the
>> capture process.

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Sakari Ailus]

Hi Steve,

On Tue, Mar 14, 2017 at 09:43:09AM -0700, Steve Longerbeam wrote:
> 
> 
> On 03/14/2017 09:21 AM, Nicolas Dufresne wrote:
> >Le lundi 13 mars 2017 à 10:45 +0000, Russell King - ARM Linux a écrit :
> >>On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
> >>>On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
> >>>>The event must be user visible, otherwise the user has no indication
> >>>>the error, and can't correct it by stream restart.
> >>>In that case the driver can detect this and call vb2_queue_error. It's
> >>>what it is there for.
> >>>
> >>>The event doesn't help you since only this driver has this issue. So nobody
> >>>will watch this event, unless it is sw specifically written for this SoC.
> >>>
> >>>Much better to call vb2_queue_error to signal a fatal error (which this
> >>>apparently is) since there are more drivers that do this, and vivid supports
> >>>triggering this condition as well.
> >>So today, I can fiddle around with the IMX219 registers to help gain
> >>an understanding of how this sensor works.  Several of the registers
> >>(such as the PLL setup [*]) require me to disable streaming on the
> >>sensor while changing them.
> >>
> >>This is something I've done many times while testing various ideas,
> >>and is my primary way of figuring out and testing such things.
> >>
> >>Whenever I resume streaming (provided I've let the sensor stop
> >>streaming at a frame boundary) it resumes as if nothing happened.  If I
> >>stop the sensor mid-frame, then I get the rolling issue that Steve
> >>reports, but once the top of the frame becomes aligned with the top of
> >>the capture, everything then becomes stable again as if nothing happened.
> >>
> >>The side effect of what you're proposing is that when I disable streaming
> >>at the sensor by poking at its registers, rather than the capture just
> >>stopping, an error is going to be delivered to gstreamer, and gstreamer
> >>is going to exit, taking the entire capture process down.
> >Indeed, there is no recovery attempt in GStreamer code, and it's hard
> >for an higher level programs to handle this. Nothing prevents from
> >adding something of course, but the errors are really un-specific, so
> >it would be something pretty blind. For what it has been tested, this
> >case was never met, usually the error is triggered by a USB camera
> >being un-plugged, a driver failure or even a firmware crash. Most of
> >the time, this is not recoverable.
> >
> >My main concern here based on what I'm reading, is that this driver is
> >not even able to notice immediately that a produced frame was corrupted
> >(because it's out of sync). From usability perspective, this is really
> >bad.
> 
> First, this is an isolated problem, specific to bt.656 and it only
> occurs when disrupting the analog video source signal in some
> way (by unplugging the RCA cable from the ADV718x connector
> for example).
> 
> Second, there is no DMA status support in i.MX6 to catch these
> shifted bt.656 codes, and the ADV718x does not provide any
> status indicators of this event either. So monitoring frame intervals
> is the only solution available, until FSL/NXP issues a new silicon rev.
> 
> 
> >  Can't the driver derive a clock from some irq and calculate for
> >each frame if the timing was correct ?
> 
> That's what is being done, essentially.
> 
> >  And if not mark the buffer with
> >V4L2_BUF_FLAG_ERROR ?
> 
> I prefer to keep the private event, V4L2_BUF_FLAG_ERROR is too
> unspecific.

Is the reason you prefer an event that you have multiple drivers involved,
or that the error flag is, well, only telling there was an error with a
particular frame?

Returning -EIO (by calling vb2_queue_error()) would be a better choice as it
is documented behaviour.

-- 
Regard,s

Sakari Ailus
e-mail: sakari.ailus@iki.fi	XMPP: sailus@retiisi.org.uk

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Sakari Ailus]

Hi Steve,

On Tue, Mar 14, 2017 at 09:43:09AM -0700, Steve Longerbeam wrote:
> 
> 
> On 03/14/2017 09:21 AM, Nicolas Dufresne wrote:
> >Le lundi 13 mars 2017 ? 10:45 +0000, Russell King - ARM Linux a ?crit :
> >>On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
> >>>On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
> >>>>The event must be user visible, otherwise the user has no indication
> >>>>the error, and can't correct it by stream restart.
> >>>In that case the driver can detect this and call vb2_queue_error. It's
> >>>what it is there for.
> >>>
> >>>The event doesn't help you since only this driver has this issue. So nobody
> >>>will watch this event, unless it is sw specifically written for this SoC.
> >>>
> >>>Much better to call vb2_queue_error to signal a fatal error (which this
> >>>apparently is) since there are more drivers that do this, and vivid supports
> >>>triggering this condition as well.
> >>So today, I can fiddle around with the IMX219 registers to help gain
> >>an understanding of how this sensor works.  Several of the registers
> >>(such as the PLL setup [*]) require me to disable streaming on the
> >>sensor while changing them.
> >>
> >>This is something I've done many times while testing various ideas,
> >>and is my primary way of figuring out and testing such things.
> >>
> >>Whenever I resume streaming (provided I've let the sensor stop
> >>streaming at a frame boundary) it resumes as if nothing happened.  If I
> >>stop the sensor mid-frame, then I get the rolling issue that Steve
> >>reports, but once the top of the frame becomes aligned with the top of
> >>the capture, everything then becomes stable again as if nothing happened.
> >>
> >>The side effect of what you're proposing is that when I disable streaming
> >>at the sensor by poking at its registers, rather than the capture just
> >>stopping, an error is going to be delivered to gstreamer, and gstreamer
> >>is going to exit, taking the entire capture process down.
> >Indeed, there is no recovery attempt in GStreamer code, and it's hard
> >for an higher level programs to handle this. Nothing prevents from
> >adding something of course, but the errors are really un-specific, so
> >it would be something pretty blind. For what it has been tested, this
> >case was never met, usually the error is triggered by a USB camera
> >being un-plugged, a driver failure or even a firmware crash. Most of
> >the time, this is not recoverable.
> >
> >My main concern here based on what I'm reading, is that this driver is
> >not even able to notice immediately that a produced frame was corrupted
> >(because it's out of sync). From usability perspective, this is really
> >bad.
> 
> First, this is an isolated problem, specific to bt.656 and it only
> occurs when disrupting the analog video source signal in some
> way (by unplugging the RCA cable from the ADV718x connector
> for example).
> 
> Second, there is no DMA status support in i.MX6 to catch these
> shifted bt.656 codes, and the ADV718x does not provide any
> status indicators of this event either. So monitoring frame intervals
> is the only solution available, until FSL/NXP issues a new silicon rev.
> 
> 
> >  Can't the driver derive a clock from some irq and calculate for
> >each frame if the timing was correct ?
> 
> That's what is being done, essentially.
> 
> >  And if not mark the buffer with
> >V4L2_BUF_FLAG_ERROR ?
> 
> I prefer to keep the private event, V4L2_BUF_FLAG_ERROR is too
> unspecific.

Is the reason you prefer an event that you have multiple drivers involved,
or that the error flag is, well, only telling there was an error with a
particular frame?

Returning -EIO (by calling vb2_queue_error()) would be a better choice as it
is documented behaviour.

-- 
Regard,s

Sakari Ailus
e-mail: sakari.ailus at iki.fi	XMPP: sailus at retiisi.org.uk

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Sakari Ailus]

Hi Steve,

On Tue, Mar 14, 2017 at 09:43:09AM -0700, Steve Longerbeam wrote:
> 
> 
> On 03/14/2017 09:21 AM, Nicolas Dufresne wrote:
> >Le lundi 13 mars 2017 à 10:45 +0000, Russell King - ARM Linux a écrit :
> >>On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
> >>>On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
> >>>>The event must be user visible, otherwise the user has no indication
> >>>>the error, and can't correct it by stream restart.
> >>>In that case the driver can detect this and call vb2_queue_error. It's
> >>>what it is there for.
> >>>
> >>>The event doesn't help you since only this driver has this issue. So nobody
> >>>will watch this event, unless it is sw specifically written for this SoC.
> >>>
> >>>Much better to call vb2_queue_error to signal a fatal error (which this
> >>>apparently is) since there are more drivers that do this, and vivid supports
> >>>triggering this condition as well.
> >>So today, I can fiddle around with the IMX219 registers to help gain
> >>an understanding of how this sensor works.  Several of the registers
> >>(such as the PLL setup [*]) require me to disable streaming on the
> >>sensor while changing them.
> >>
> >>This is something I've done many times while testing various ideas,
> >>and is my primary way of figuring out and testing such things.
> >>
> >>Whenever I resume streaming (provided I've let the sensor stop
> >>streaming at a frame boundary) it resumes as if nothing happened.  If I
> >>stop the sensor mid-frame, then I get the rolling issue that Steve
> >>reports, but once the top of the frame becomes aligned with the top of
> >>the capture, everything then becomes stable again as if nothing happened.
> >>
> >>The side effect of what you're proposing is that when I disable streaming
> >>at the sensor by poking at its registers, rather than the capture just
> >>stopping, an error is going to be delivered to gstreamer, and gstreamer
> >>is going to exit, taking the entire capture process down.
> >Indeed, there is no recovery attempt in GStreamer code, and it's hard
> >for an higher level programs to handle this. Nothing prevents from
> >adding something of course, but the errors are really un-specific, so
> >it would be something pretty blind. For what it has been tested, this
> >case was never met, usually the error is triggered by a USB camera
> >being un-plugged, a driver failure or even a firmware crash. Most of
> >the time, this is not recoverable.
> >
> >My main concern here based on what I'm reading, is that this driver is
> >not even able to notice immediately that a produced frame was corrupted
> >(because it's out of sync). From usability perspective, this is really
> >bad.
> 
> First, this is an isolated problem, specific to bt.656 and it only
> occurs when disrupting the analog video source signal in some
> way (by unplugging the RCA cable from the ADV718x connector
> for example).
> 
> Second, there is no DMA status support in i.MX6 to catch these
> shifted bt.656 codes, and the ADV718x does not provide any
> status indicators of this event either. So monitoring frame intervals
> is the only solution available, until FSL/NXP issues a new silicon rev.
> 
> 
> >  Can't the driver derive a clock from some irq and calculate for
> >each frame if the timing was correct ?
> 
> That's what is being done, essentially.
> 
> >  And if not mark the buffer with
> >V4L2_BUF_FLAG_ERROR ?
> 
> I prefer to keep the private event, V4L2_BUF_FLAG_ERROR is too
> unspecific.

Is the reason you prefer an event that you have multiple drivers involved,
or that the error flag is, well, only telling there was an error with a
particular frame?

Returning -EIO (by calling vb2_queue_error()) would be a better choice as it
is documented behaviour.

-- 
Regard,s

Sakari Ailus
e-mail: sakari.ailus@iki.fi	XMPP: sailus@retiisi.org.uk

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Russell King - ARM Linux]

On Tue, Mar 14, 2017 at 12:21:31PM -0400, Nicolas Dufresne wrote:
> My main concern here based on what I'm reading, is that this driver is
> not even able to notice immediately that a produced frame was corrupted
> (because it's out of sync). From usability perspective, this is really
> bad. Can't the driver derive a clock from some irq and calculate for
> each frame if the timing was correct ? And if not mark the buffer with
> V4L2_BUF_FLAG_ERROR ?

One of the issues of measuring timing with IRQs is the fact that the
IRQ subsystem only allows one IRQ to run at a time.  If an IRQ takes
a relatively long time to process, then it throws the timing of other
IRQs out.

If you're going to decide that a buffer should be marked in error on
the basis of an interrupt arriving late, this can trigger spuriously.

It wasn't that long ago that USB HID was regularly eating something
like 20ms of interrupt time... that's been solved, but that doesn't
mean all cases are solved - there are still interrupt handlers in the
kernel that are on the order of milliseconds to complete.

Given the quality I observe of some USB serial devices (eg, running at
115200 baud, but feeling like they deliver characters to userspace at
9600 baud) I wouldn't be surprised if some USB serial drivers eat a lot
of IRQ time... and if so, all it'll take is to plug such a device in
to disrupt capture.

That sounds way too fragile to me.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Russell King - ARM Linux]

On Tue, Mar 14, 2017 at 12:21:31PM -0400, Nicolas Dufresne wrote:
> My main concern here based on what I'm reading, is that this driver is
> not even able to notice immediately that a produced frame was corrupted
> (because it's out of sync). From usability perspective, this is really
> bad. Can't the driver derive a clock from some irq and calculate for
> each frame if the timing was correct ? And if not mark the buffer with
> V4L2_BUF_FLAG_ERROR ?

One of the issues of measuring timing with IRQs is the fact that the
IRQ subsystem only allows one IRQ to run at a time.  If an IRQ takes
a relatively long time to process, then it throws the timing of other
IRQs out.

If you're going to decide that a buffer should be marked in error on
the basis of an interrupt arriving late, this can trigger spuriously.

It wasn't that long ago that USB HID was regularly eating something
like 20ms of interrupt time... that's been solved, but that doesn't
mean all cases are solved - there are still interrupt handlers in the
kernel that are on the order of milliseconds to complete.

Given the quality I observe of some USB serial devices (eg, running at
115200 baud, but feeling like they deliver characters to userspace at
9600 baud) I wouldn't be surprised if some USB serial drivers eat a lot
of IRQ time... and if so, all it'll take is to plug such a device in
to disrupt capture.

That sounds way too fragile to me.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Russell King - ARM Linux]

On Tue, Mar 14, 2017 at 12:21:31PM -0400, Nicolas Dufresne wrote:
> My main concern here based on what I'm reading, is that this driver is
> not even able to notice immediately that a produced frame was corrupted
> (because it's out of sync). From usability perspective, this is really
> bad. Can't the driver derive a clock from some irq and calculate for
> each frame if the timing was correct ? And if not mark the buffer with
> V4L2_BUF_FLAG_ERROR ?

One of the issues of measuring timing with IRQs is the fact that the
IRQ subsystem only allows one IRQ to run at a time.  If an IRQ takes
a relatively long time to process, then it throws the timing of other
IRQs out.

If you're going to decide that a buffer should be marked in error on
the basis of an interrupt arriving late, this can trigger spuriously.

It wasn't that long ago that USB HID was regularly eating something
like 20ms of interrupt time... that's been solved, but that doesn't
mean all cases are solved - there are still interrupt handlers in the
kernel that are on the order of milliseconds to complete.

Given the quality I observe of some USB serial devices (eg, running at
115200 baud, but feeling like they deliver characters to userspace at
9600 baud) I wouldn't be surprised if some USB serial drivers eat a lot
of IRQ time... and if so, all it'll take is to plug such a device in
to disrupt capture.

That sounds way too fragile to me.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/14/2017 09:47 AM, Russell King - ARM Linux wrote:
> On Tue, Mar 14, 2017 at 12:21:31PM -0400, Nicolas Dufresne wrote:
>> My main concern here based on what I'm reading, is that this driver is
>> not even able to notice immediately that a produced frame was corrupted
>> (because it's out of sync). From usability perspective, this is really
>> bad. Can't the driver derive a clock from some irq and calculate for
>> each frame if the timing was correct ? And if not mark the buffer with
>> V4L2_BUF_FLAG_ERROR ?
> One of the issues of measuring timing with IRQs is the fact that the
> IRQ subsystem only allows one IRQ to run at a time.  If an IRQ takes
> a relatively long time to process, then it throws the timing of other
> IRQs out.
>
> If you're going to decide that a buffer should be marked in error on
> the basis of an interrupt arriving late, this can trigger spuriously.
>
> It wasn't that long ago that USB HID was regularly eating something
> like 20ms of interrupt time... that's been solved, but that doesn't
> mean all cases are solved - there are still interrupt handlers in the
> kernel that are on the order of milliseconds to complete.
>
> Given the quality I observe of some USB serial devices (eg, running at
> 115200 baud, but feeling like they deliver characters to userspace at
> 9600 baud) I wouldn't be surprised if some USB serial drivers eat a lot
> of IRQ time... and if so, all it'll take is to plug such a device in
> to disrupt capture.
>
> That sounds way too fragile to me.

exactly, hence the imx6 timer input capture support.

Steve

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/14/2017 09:47 AM, Russell King - ARM Linux wrote:
> On Tue, Mar 14, 2017 at 12:21:31PM -0400, Nicolas Dufresne wrote:
>> My main concern here based on what I'm reading, is that this driver is
>> not even able to notice immediately that a produced frame was corrupted
>> (because it's out of sync). From usability perspective, this is really
>> bad. Can't the driver derive a clock from some irq and calculate for
>> each frame if the timing was correct ? And if not mark the buffer with
>> V4L2_BUF_FLAG_ERROR ?
> One of the issues of measuring timing with IRQs is the fact that the
> IRQ subsystem only allows one IRQ to run at a time.  If an IRQ takes
> a relatively long time to process, then it throws the timing of other
> IRQs out.
>
> If you're going to decide that a buffer should be marked in error on
> the basis of an interrupt arriving late, this can trigger spuriously.
>
> It wasn't that long ago that USB HID was regularly eating something
> like 20ms of interrupt time... that's been solved, but that doesn't
> mean all cases are solved - there are still interrupt handlers in the
> kernel that are on the order of milliseconds to complete.
>
> Given the quality I observe of some USB serial devices (eg, running at
> 115200 baud, but feeling like they deliver characters to userspace at
> 9600 baud) I wouldn't be surprised if some USB serial drivers eat a lot
> of IRQ time... and if so, all it'll take is to plug such a device in
> to disrupt capture.
>
> That sounds way too fragile to me.

exactly, hence the imx6 timer input capture support.

Steve

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Steve Longerbeam]

On 03/14/2017 09:47 AM, Russell King - ARM Linux wrote:
> On Tue, Mar 14, 2017 at 12:21:31PM -0400, Nicolas Dufresne wrote:
>> My main concern here based on what I'm reading, is that this driver is
>> not even able to notice immediately that a produced frame was corrupted
>> (because it's out of sync). From usability perspective, this is really
>> bad. Can't the driver derive a clock from some irq and calculate for
>> each frame if the timing was correct ? And if not mark the buffer with
>> V4L2_BUF_FLAG_ERROR ?
> One of the issues of measuring timing with IRQs is the fact that the
> IRQ subsystem only allows one IRQ to run at a time.  If an IRQ takes
> a relatively long time to process, then it throws the timing of other
> IRQs out.
>
> If you're going to decide that a buffer should be marked in error on
> the basis of an interrupt arriving late, this can trigger spuriously.
>
> It wasn't that long ago that USB HID was regularly eating something
> like 20ms of interrupt time... that's been solved, but that doesn't
> mean all cases are solved - there are still interrupt handlers in the
> kernel that are on the order of milliseconds to complete.
>
> Given the quality I observe of some USB serial devices (eg, running at
> 115200 baud, but feeling like they deliver characters to userspace at
> 9600 baud) I wouldn't be surprised if some USB serial drivers eat a lot
> of IRQ time... and if so, all it'll take is to plug such a device in
> to disrupt capture.
>
> That sounds way too fragile to me.

exactly, hence the imx6 timer input capture support.

Steve

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 2392 bytes --]

On Mon 2017-03-13 10:45:38, Russell King - ARM Linux wrote:
> On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
> > On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
> > > The event must be user visible, otherwise the user has no indication
> > > the error, and can't correct it by stream restart.
> > 
> > In that case the driver can detect this and call vb2_queue_error. It's
> > what it is there for.
> > 
> > The event doesn't help you since only this driver has this issue. So nobody
> > will watch this event, unless it is sw specifically written for this SoC.
> > 
> > Much better to call vb2_queue_error to signal a fatal error (which this
> > apparently is) since there are more drivers that do this, and vivid supports
> > triggering this condition as well.
> 
> So today, I can fiddle around with the IMX219 registers to help gain
> an understanding of how this sensor works.  Several of the registers
> (such as the PLL setup [*]) require me to disable streaming on the
> sensor while changing them.
> 
> This is something I've done many times while testing various ideas,
> and is my primary way of figuring out and testing such things.
> 
> Whenever I resume streaming (provided I've let the sensor stop
> streaming at a frame boundary) it resumes as if nothing happened.  If I
> stop the sensor mid-frame, then I get the rolling issue that Steve
> reports, but once the top of the frame becomes aligned with the top of
> the capture, everything then becomes stable again as if nothing happened.
> 
> The side effect of what you're proposing is that when I disable streaming
> at the sensor by poking at its registers, rather than the capture just
> stopping, an error is going to be delivered to gstreamer, and gstreamer
> is going to exit, taking the entire capture process down.
> 
> This severely restricts the ability to be able to develop and test
> sensor drivers.

Well, but kernel should do what is best for production, not what is
best for driver debugging.

And yes, I guess you can have #ifdef or module parameter or something
switching for behaviour you prefer when you are debugging. But for
production, vb2_queue_error() seems to be the right solution.

								Pavel
-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

[PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Pavel Machek]

On Mon 2017-03-13 10:45:38, Russell King - ARM Linux wrote:
> On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
> > On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
> > > The event must be user visible, otherwise the user has no indication
> > > the error, and can't correct it by stream restart.
> > 
> > In that case the driver can detect this and call vb2_queue_error. It's
> > what it is there for.
> > 
> > The event doesn't help you since only this driver has this issue. So nobody
> > will watch this event, unless it is sw specifically written for this SoC.
> > 
> > Much better to call vb2_queue_error to signal a fatal error (which this
> > apparently is) since there are more drivers that do this, and vivid supports
> > triggering this condition as well.
> 
> So today, I can fiddle around with the IMX219 registers to help gain
> an understanding of how this sensor works.  Several of the registers
> (such as the PLL setup [*]) require me to disable streaming on the
> sensor while changing them.
> 
> This is something I've done many times while testing various ideas,
> and is my primary way of figuring out and testing such things.
> 
> Whenever I resume streaming (provided I've let the sensor stop
> streaming at a frame boundary) it resumes as if nothing happened.  If I
> stop the sensor mid-frame, then I get the rolling issue that Steve
> reports, but once the top of the frame becomes aligned with the top of
> the capture, everything then becomes stable again as if nothing happened.
> 
> The side effect of what you're proposing is that when I disable streaming
> at the sensor by poking at its registers, rather than the capture just
> stopping, an error is going to be delivered to gstreamer, and gstreamer
> is going to exit, taking the entire capture process down.
> 
> This severely restricts the ability to be able to develop and test
> sensor drivers.

Well, but kernel should do what is best for production, not what is
best for driver debugging.

And yes, I guess you can have #ifdef or module parameter or something
switching for behaviour you prefer when you are debugging. But for
production, vb2_queue_error() seems to be the right solution.

								Pavel
-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 181 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170314/b79f73d5/attachment-0001.sig>

Re: [PATCH v5 15/39] [media] v4l2: add a frame interval error event

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 2392 bytes --]

On Mon 2017-03-13 10:45:38, Russell King - ARM Linux wrote:
> On Mon, Mar 13, 2017 at 11:02:34AM +0100, Hans Verkuil wrote:
> > On 03/11/2017 07:14 PM, Steve Longerbeam wrote:
> > > The event must be user visible, otherwise the user has no indication
> > > the error, and can't correct it by stream restart.
> > 
> > In that case the driver can detect this and call vb2_queue_error. It's
> > what it is there for.
> > 
> > The event doesn't help you since only this driver has this issue. So nobody
> > will watch this event, unless it is sw specifically written for this SoC.
> > 
> > Much better to call vb2_queue_error to signal a fatal error (which this
> > apparently is) since there are more drivers that do this, and vivid supports
> > triggering this condition as well.
> 
> So today, I can fiddle around with the IMX219 registers to help gain
> an understanding of how this sensor works.  Several of the registers
> (such as the PLL setup [*]) require me to disable streaming on the
> sensor while changing them.
> 
> This is something I've done many times while testing various ideas,
> and is my primary way of figuring out and testing such things.
> 
> Whenever I resume streaming (provided I've let the sensor stop
> streaming at a frame boundary) it resumes as if nothing happened.  If I
> stop the sensor mid-frame, then I get the rolling issue that Steve
> reports, but once the top of the frame becomes aligned with the top of
> the capture, everything then becomes stable again as if nothing happened.
> 
> The side effect of what you're proposing is that when I disable streaming
> at the sensor by poking at its registers, rather than the capture just
> stopping, an error is going to be delivered to gstreamer, and gstreamer
> is going to exit, taking the entire capture process down.
> 
> This severely restricts the ability to be able to develop and test
> sensor drivers.

Well, but kernel should do what is best for production, not what is
best for driver debugging.

And yes, I guess you can have #ifdef or module parameter or something
switching for behaviour you prefer when you are debugging. But for
production, vb2_queue_error() seems to be the right solution.

								Pavel
-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

[PATCH v5 16/39] [media] v4l2: add a new-frame before end-of-frame event

[Steve Longerbeam]

Add a NEW_FRAME_BEFORE_EOF event to signal that a video capture or
output device has signaled a new frame is ready before a previous
frame has completed reception or transmission. This usually indicates
a DMA read/write channel is having trouble gaining bus access.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 Documentation/media/uapi/v4l/vidioc-dqevent.rst | 6 ++++++
 Documentation/media/videodev2.h.rst.exceptions  | 1 +
 include/uapi/linux/videodev2.h                  | 1 +
 3 files changed, 8 insertions(+)

diff --git a/Documentation/media/uapi/v4l/vidioc-dqevent.rst b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
index dc77363..54bc7ae 100644
--- a/Documentation/media/uapi/v4l/vidioc-dqevent.rst
+++ b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
@@ -203,6 +203,12 @@ call.
 	has measured an interval between the reception or transmit
 	completion of two consecutive frames of video that is outside
 	the nominal frame interval by some tolerance value.
+    * - ``V4L2_EVENT_NEW_FRAME_BEFORE_EOF``
+      - 8
+      - This event is triggered when the video capture or output device
+	has signaled a new frame is ready before a previous frame has
+	completed reception or transmission. This usually indicates a
+	DMA read/write channel is having trouble gaining bus access.
     * - ``V4L2_EVENT_PRIVATE_START``
       - 0x08000000
       - Base event number for driver-private events.
diff --git a/Documentation/media/videodev2.h.rst.exceptions b/Documentation/media/videodev2.h.rst.exceptions
index c7d8fad..be6f332 100644
--- a/Documentation/media/videodev2.h.rst.exceptions
+++ b/Documentation/media/videodev2.h.rst.exceptions
@@ -460,6 +460,7 @@ replace define V4L2_EVENT_FRAME_SYNC event-type
 replace define V4L2_EVENT_SOURCE_CHANGE event-type
 replace define V4L2_EVENT_MOTION_DET event-type
 replace define V4L2_EVENT_FRAME_INTERVAL_ERROR event-type
+replace define V4L2_EVENT_NEW_FRAME_BEFORE_EOF event-type
 replace define V4L2_EVENT_PRIVATE_START event-type
 
 replace define V4L2_EVENT_CTRL_CH_VALUE ctrl-changes-flags
diff --git a/include/uapi/linux/videodev2.h b/include/uapi/linux/videodev2.h
index cf5a0d0..f54a82a 100644
--- a/include/uapi/linux/videodev2.h
+++ b/include/uapi/linux/videodev2.h
@@ -2132,6 +2132,7 @@ struct v4l2_streamparm {
 #define V4L2_EVENT_SOURCE_CHANGE		5
 #define V4L2_EVENT_MOTION_DET			6
 #define V4L2_EVENT_FRAME_INTERVAL_ERROR		7
+#define V4L2_EVENT_NEW_FRAME_BEFORE_EOF		8
 #define V4L2_EVENT_PRIVATE_START		0x08000000
 
 /* Payload for V4L2_EVENT_VSYNC */
-- 
2.7.4

[PATCH v5 16/39] [media] v4l2: add a new-frame before end-of-frame event

[Steve Longerbeam]

Add a NEW_FRAME_BEFORE_EOF event to signal that a video capture or
output device has signaled a new frame is ready before a previous
frame has completed reception or transmission. This usually indicates
a DMA read/write channel is having trouble gaining bus access.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 Documentation/media/uapi/v4l/vidioc-dqevent.rst | 6 ++++++
 Documentation/media/videodev2.h.rst.exceptions  | 1 +
 include/uapi/linux/videodev2.h                  | 1 +
 3 files changed, 8 insertions(+)

diff --git a/Documentation/media/uapi/v4l/vidioc-dqevent.rst b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
index dc77363..54bc7ae 100644
--- a/Documentation/media/uapi/v4l/vidioc-dqevent.rst
+++ b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
@@ -203,6 +203,12 @@ call.
 	has measured an interval between the reception or transmit
 	completion of two consecutive frames of video that is outside
 	the nominal frame interval by some tolerance value.
+    * - ``V4L2_EVENT_NEW_FRAME_BEFORE_EOF``
+      - 8
+      - This event is triggered when the video capture or output device
+	has signaled a new frame is ready before a previous frame has
+	completed reception or transmission. This usually indicates a
+	DMA read/write channel is having trouble gaining bus access.
     * - ``V4L2_EVENT_PRIVATE_START``
       - 0x08000000
       - Base event number for driver-private events.
diff --git a/Documentation/media/videodev2.h.rst.exceptions b/Documentation/media/videodev2.h.rst.exceptions
index c7d8fad..be6f332 100644
--- a/Documentation/media/videodev2.h.rst.exceptions
+++ b/Documentation/media/videodev2.h.rst.exceptions
@@ -460,6 +460,7 @@ replace define V4L2_EVENT_FRAME_SYNC event-type
 replace define V4L2_EVENT_SOURCE_CHANGE event-type
 replace define V4L2_EVENT_MOTION_DET event-type
 replace define V4L2_EVENT_FRAME_INTERVAL_ERROR event-type
+replace define V4L2_EVENT_NEW_FRAME_BEFORE_EOF event-type
 replace define V4L2_EVENT_PRIVATE_START event-type
 
 replace define V4L2_EVENT_CTRL_CH_VALUE ctrl-changes-flags
diff --git a/include/uapi/linux/videodev2.h b/include/uapi/linux/videodev2.h
index cf5a0d0..f54a82a 100644
--- a/include/uapi/linux/videodev2.h
+++ b/include/uapi/linux/videodev2.h
@@ -2132,6 +2132,7 @@ struct v4l2_streamparm {
 #define V4L2_EVENT_SOURCE_CHANGE		5
 #define V4L2_EVENT_MOTION_DET			6
 #define V4L2_EVENT_FRAME_INTERVAL_ERROR		7
+#define V4L2_EVENT_NEW_FRAME_BEFORE_EOF		8
 #define V4L2_EVENT_PRIVATE_START		0x08000000
 
 /* Payload for V4L2_EVENT_VSYNC */
-- 
2.7.4

[PATCH v5 16/39] [media] v4l2: add a new-frame before end-of-frame event

[Steve Longerbeam]

Add a NEW_FRAME_BEFORE_EOF event to signal that a video capture or
output device has signaled a new frame is ready before a previous
frame has completed reception or transmission. This usually indicates
a DMA read/write channel is having trouble gaining bus access.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 Documentation/media/uapi/v4l/vidioc-dqevent.rst | 6 ++++++
 Documentation/media/videodev2.h.rst.exceptions  | 1 +
 include/uapi/linux/videodev2.h                  | 1 +
 3 files changed, 8 insertions(+)

diff --git a/Documentation/media/uapi/v4l/vidioc-dqevent.rst b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
index dc77363..54bc7ae 100644
--- a/Documentation/media/uapi/v4l/vidioc-dqevent.rst
+++ b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
@@ -203,6 +203,12 @@ call.
 	has measured an interval between the reception or transmit
 	completion of two consecutive frames of video that is outside
 	the nominal frame interval by some tolerance value.
+    * - ``V4L2_EVENT_NEW_FRAME_BEFORE_EOF``
+      - 8
+      - This event is triggered when the video capture or output device
+	has signaled a new frame is ready before a previous frame has
+	completed reception or transmission. This usually indicates a
+	DMA read/write channel is having trouble gaining bus access.
     * - ``V4L2_EVENT_PRIVATE_START``
       - 0x08000000
       - Base event number for driver-private events.
diff --git a/Documentation/media/videodev2.h.rst.exceptions b/Documentation/media/videodev2.h.rst.exceptions
index c7d8fad..be6f332 100644
--- a/Documentation/media/videodev2.h.rst.exceptions
+++ b/Documentation/media/videodev2.h.rst.exceptions
@@ -460,6 +460,7 @@ replace define V4L2_EVENT_FRAME_SYNC event-type
 replace define V4L2_EVENT_SOURCE_CHANGE event-type
 replace define V4L2_EVENT_MOTION_DET event-type
 replace define V4L2_EVENT_FRAME_INTERVAL_ERROR event-type
+replace define V4L2_EVENT_NEW_FRAME_BEFORE_EOF event-type
 replace define V4L2_EVENT_PRIVATE_START event-type
 
 replace define V4L2_EVENT_CTRL_CH_VALUE ctrl-changes-flags
diff --git a/include/uapi/linux/videodev2.h b/include/uapi/linux/videodev2.h
index cf5a0d0..f54a82a 100644
--- a/include/uapi/linux/videodev2.h
+++ b/include/uapi/linux/videodev2.h
@@ -2132,6 +2132,7 @@ struct v4l2_streamparm {
 #define V4L2_EVENT_SOURCE_CHANGE		5
 #define V4L2_EVENT_MOTION_DET			6
 #define V4L2_EVENT_FRAME_INTERVAL_ERROR		7
+#define V4L2_EVENT_NEW_FRAME_BEFORE_EOF		8
 #define V4L2_EVENT_PRIVATE_START		0x08000000
 
 /* Payload for V4L2_EVENT_VSYNC */
-- 
2.7.4

Re: [PATCH v5 16/39] [media] v4l2: add a new-frame before end-of-frame event

[Hans Verkuil]

On 10/03/17 05:52, Steve Longerbeam wrote:
> Add a NEW_FRAME_BEFORE_EOF event to signal that a video capture or
> output device has signaled a new frame is ready before a previous
> frame has completed reception or transmission. This usually indicates
> a DMA read/write channel is having trouble gaining bus access.

This too is a weird event. Based on what you describe this basically means
that the previous frame is incomplete, in which case you would typically
return the buffer with the V4L2_BUF_FLAG_ERROR bit set.

Using an event for this is not a good idea.

Regards,

	Hans

> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> ---
>  Documentation/media/uapi/v4l/vidioc-dqevent.rst | 6 ++++++
>  Documentation/media/videodev2.h.rst.exceptions  | 1 +
>  include/uapi/linux/videodev2.h                  | 1 +
>  3 files changed, 8 insertions(+)
> 
> diff --git a/Documentation/media/uapi/v4l/vidioc-dqevent.rst b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
> index dc77363..54bc7ae 100644
> --- a/Documentation/media/uapi/v4l/vidioc-dqevent.rst
> +++ b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
> @@ -203,6 +203,12 @@ call.
>  	has measured an interval between the reception or transmit
>  	completion of two consecutive frames of video that is outside
>  	the nominal frame interval by some tolerance value.
> +    * - ``V4L2_EVENT_NEW_FRAME_BEFORE_EOF``
> +      - 8
> +      - This event is triggered when the video capture or output device
> +	has signaled a new frame is ready before a previous frame has
> +	completed reception or transmission. This usually indicates a
> +	DMA read/write channel is having trouble gaining bus access.
>      * - ``V4L2_EVENT_PRIVATE_START``
>        - 0x08000000
>        - Base event number for driver-private events.
> diff --git a/Documentation/media/videodev2.h.rst.exceptions b/Documentation/media/videodev2.h.rst.exceptions
> index c7d8fad..be6f332 100644
> --- a/Documentation/media/videodev2.h.rst.exceptions
> +++ b/Documentation/media/videodev2.h.rst.exceptions
> @@ -460,6 +460,7 @@ replace define V4L2_EVENT_FRAME_SYNC event-type
>  replace define V4L2_EVENT_SOURCE_CHANGE event-type
>  replace define V4L2_EVENT_MOTION_DET event-type
>  replace define V4L2_EVENT_FRAME_INTERVAL_ERROR event-type
> +replace define V4L2_EVENT_NEW_FRAME_BEFORE_EOF event-type
>  replace define V4L2_EVENT_PRIVATE_START event-type
>  
>  replace define V4L2_EVENT_CTRL_CH_VALUE ctrl-changes-flags
> diff --git a/include/uapi/linux/videodev2.h b/include/uapi/linux/videodev2.h
> index cf5a0d0..f54a82a 100644
> --- a/include/uapi/linux/videodev2.h
> +++ b/include/uapi/linux/videodev2.h
> @@ -2132,6 +2132,7 @@ struct v4l2_streamparm {
>  #define V4L2_EVENT_SOURCE_CHANGE		5
>  #define V4L2_EVENT_MOTION_DET			6
>  #define V4L2_EVENT_FRAME_INTERVAL_ERROR		7
> +#define V4L2_EVENT_NEW_FRAME_BEFORE_EOF		8
>  #define V4L2_EVENT_PRIVATE_START		0x08000000
>  
>  /* Payload for V4L2_EVENT_VSYNC */
> 

[PATCH v5 16/39] [media] v4l2: add a new-frame before end-of-frame event

[Hans Verkuil]

On 10/03/17 05:52, Steve Longerbeam wrote:
> Add a NEW_FRAME_BEFORE_EOF event to signal that a video capture or
> output device has signaled a new frame is ready before a previous
> frame has completed reception or transmission. This usually indicates
> a DMA read/write channel is having trouble gaining bus access.

This too is a weird event. Based on what you describe this basically means
that the previous frame is incomplete, in which case you would typically
return the buffer with the V4L2_BUF_FLAG_ERROR bit set.

Using an event for this is not a good idea.

Regards,

	Hans

> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> ---
>  Documentation/media/uapi/v4l/vidioc-dqevent.rst | 6 ++++++
>  Documentation/media/videodev2.h.rst.exceptions  | 1 +
>  include/uapi/linux/videodev2.h                  | 1 +
>  3 files changed, 8 insertions(+)
> 
> diff --git a/Documentation/media/uapi/v4l/vidioc-dqevent.rst b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
> index dc77363..54bc7ae 100644
> --- a/Documentation/media/uapi/v4l/vidioc-dqevent.rst
> +++ b/Documentation/media/uapi/v4l/vidioc-dqevent.rst
> @@ -203,6 +203,12 @@ call.
>  	has measured an interval between the reception or transmit
>  	completion of two consecutive frames of video that is outside
>  	the nominal frame interval by some tolerance value.
> +    * - ``V4L2_EVENT_NEW_FRAME_BEFORE_EOF``
> +      - 8
> +      - This event is triggered when the video capture or output device
> +	has signaled a new frame is ready before a previous frame has
> +	completed reception or transmission. This usually indicates a
> +	DMA read/write channel is having trouble gaining bus access.
>      * - ``V4L2_EVENT_PRIVATE_START``
>        - 0x08000000
>        - Base event number for driver-private events.
> diff --git a/Documentation/media/videodev2.h.rst.exceptions b/Documentation/media/videodev2.h.rst.exceptions
> index c7d8fad..be6f332 100644
> --- a/Documentation/media/videodev2.h.rst.exceptions
> +++ b/Documentation/media/videodev2.h.rst.exceptions
> @@ -460,6 +460,7 @@ replace define V4L2_EVENT_FRAME_SYNC event-type
>  replace define V4L2_EVENT_SOURCE_CHANGE event-type
>  replace define V4L2_EVENT_MOTION_DET event-type
>  replace define V4L2_EVENT_FRAME_INTERVAL_ERROR event-type
> +replace define V4L2_EVENT_NEW_FRAME_BEFORE_EOF event-type
>  replace define V4L2_EVENT_PRIVATE_START event-type
>  
>  replace define V4L2_EVENT_CTRL_CH_VALUE ctrl-changes-flags
> diff --git a/include/uapi/linux/videodev2.h b/include/uapi/linux/videodev2.h
> index cf5a0d0..f54a82a 100644
> --- a/include/uapi/linux/videodev2.h
> +++ b/include/uapi/linux/videodev2.h
> @@ -2132,6 +2132,7 @@ struct v4l2_streamparm {
>  #define V4L2_EVENT_SOURCE_CHANGE		5
>  #define V4L2_EVENT_MOTION_DET			6
>  #define V4L2_EVENT_FRAME_INTERVAL_ERROR		7
> +#define V4L2_EVENT_NEW_FRAME_BEFORE_EOF		8
>  #define V4L2_EVENT_PRIVATE_START		0x08000000
>  
>  /* Payload for V4L2_EVENT_VSYNC */
> 

[PATCH v5 17/39] [media] v4l2-mc: add a function to inherit controls from a pipeline

[Steve Longerbeam]

v4l2_pipeline_inherit_controls() will add the v4l2 controls from
all subdev entities in a pipeline to a given video device.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/media/v4l2-core/v4l2-mc.c | 48 +++++++++++++++++++++++++++++++++++++++
 include/media/v4l2-mc.h           | 25 ++++++++++++++++++++
 2 files changed, 73 insertions(+)

diff --git a/drivers/media/v4l2-core/v4l2-mc.c b/drivers/media/v4l2-core/v4l2-mc.c
index 303980b..09d4d97 100644
--- a/drivers/media/v4l2-core/v4l2-mc.c
+++ b/drivers/media/v4l2-core/v4l2-mc.c
@@ -22,6 +22,7 @@
 #include <linux/usb.h>
 #include <media/media-device.h>
 #include <media/media-entity.h>
+#include <media/v4l2-ctrls.h>
 #include <media/v4l2-fh.h>
 #include <media/v4l2-mc.h>
 #include <media/v4l2-subdev.h>
@@ -238,6 +239,53 @@ int v4l_vb2q_enable_media_source(struct vb2_queue *q)
 }
 EXPORT_SYMBOL_GPL(v4l_vb2q_enable_media_source);
 
+int __v4l2_pipeline_inherit_controls(struct video_device *vfd,
+				     struct media_entity *start_entity)
+{
+	struct media_device *mdev = start_entity->graph_obj.mdev;
+	struct media_entity *entity;
+	struct media_graph graph;
+	struct v4l2_subdev *sd;
+	int ret;
+
+	ret = media_graph_walk_init(&graph, mdev);
+	if (ret)
+		return ret;
+
+	media_graph_walk_start(&graph, start_entity);
+
+	while ((entity = media_graph_walk_next(&graph))) {
+		if (!is_media_entity_v4l2_subdev(entity))
+			continue;
+
+		sd = media_entity_to_v4l2_subdev(entity);
+
+		ret = v4l2_ctrl_add_handler(vfd->ctrl_handler,
+					    sd->ctrl_handler,
+					    NULL);
+		if (ret)
+			break;
+	}
+
+	media_graph_walk_cleanup(&graph);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(__v4l2_pipeline_inherit_controls);
+
+int v4l2_pipeline_inherit_controls(struct video_device *vfd,
+				   struct media_entity *start_entity)
+{
+	struct media_device *mdev = start_entity->graph_obj.mdev;
+	int ret;
+
+	mutex_lock(&mdev->graph_mutex);
+	ret = __v4l2_pipeline_inherit_controls(vfd, start_entity);
+	mutex_unlock(&mdev->graph_mutex);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(v4l2_pipeline_inherit_controls);
+
 /* -----------------------------------------------------------------------------
  * Pipeline power management
  *
diff --git a/include/media/v4l2-mc.h b/include/media/v4l2-mc.h
index 2634d9d..9848e77 100644
--- a/include/media/v4l2-mc.h
+++ b/include/media/v4l2-mc.h
@@ -171,6 +171,17 @@ void v4l_disable_media_source(struct video_device *vdev);
  */
 int v4l_vb2q_enable_media_source(struct vb2_queue *q);
 
+/**
+ * v4l2_pipeline_inherit_controls - Add the v4l2 controls from all
+ *				    subdev entities in a pipeline to
+ *				    the given video device.
+ * @vfd: the video device
+ * @start_entity: Starting entity
+ */
+int __v4l2_pipeline_inherit_controls(struct video_device *vfd,
+				     struct media_entity *start_entity);
+int v4l2_pipeline_inherit_controls(struct video_device *vfd,
+				   struct media_entity *start_entity);
 
 /**
  * v4l2_pipeline_pm_use - Update the use count of an entity
@@ -231,6 +242,20 @@ static inline int v4l_vb2q_enable_media_source(struct vb2_queue *q)
 	return 0;
 }
 
+static inline int __v4l2_pipeline_inherit_controls(
+	struct video_device *vfd,
+	struct media_entity *start_entity)
+{
+	return 0;
+}
+
+static inline int v4l2_pipeline_inherit_controls(
+	struct video_device *vfd,
+	struct media_entity *start_entity)
+{
+	return 0;
+}
+
 static inline int v4l2_pipeline_pm_use(struct media_entity *entity, int use)
 {
 	return 0;
-- 
2.7.4

[PATCH v5 17/39] [media] v4l2-mc: add a function to inherit controls from a pipeline

[Steve Longerbeam]

v4l2_pipeline_inherit_controls() will add the v4l2 controls from
all subdev entities in a pipeline to a given video device.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/media/v4l2-core/v4l2-mc.c | 48 +++++++++++++++++++++++++++++++++++++++
 include/media/v4l2-mc.h           | 25 ++++++++++++++++++++
 2 files changed, 73 insertions(+)

diff --git a/drivers/media/v4l2-core/v4l2-mc.c b/drivers/media/v4l2-core/v4l2-mc.c
index 303980b..09d4d97 100644
--- a/drivers/media/v4l2-core/v4l2-mc.c
+++ b/drivers/media/v4l2-core/v4l2-mc.c
@@ -22,6 +22,7 @@
 #include <linux/usb.h>
 #include <media/media-device.h>
 #include <media/media-entity.h>
+#include <media/v4l2-ctrls.h>
 #include <media/v4l2-fh.h>
 #include <media/v4l2-mc.h>
 #include <media/v4l2-subdev.h>
@@ -238,6 +239,53 @@ int v4l_vb2q_enable_media_source(struct vb2_queue *q)
 }
 EXPORT_SYMBOL_GPL(v4l_vb2q_enable_media_source);
 
+int __v4l2_pipeline_inherit_controls(struct video_device *vfd,
+				     struct media_entity *start_entity)
+{
+	struct media_device *mdev = start_entity->graph_obj.mdev;
+	struct media_entity *entity;
+	struct media_graph graph;
+	struct v4l2_subdev *sd;
+	int ret;
+
+	ret = media_graph_walk_init(&graph, mdev);
+	if (ret)
+		return ret;
+
+	media_graph_walk_start(&graph, start_entity);
+
+	while ((entity = media_graph_walk_next(&graph))) {
+		if (!is_media_entity_v4l2_subdev(entity))
+			continue;
+
+		sd = media_entity_to_v4l2_subdev(entity);
+
+		ret = v4l2_ctrl_add_handler(vfd->ctrl_handler,
+					    sd->ctrl_handler,
+					    NULL);
+		if (ret)
+			break;
+	}
+
+	media_graph_walk_cleanup(&graph);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(__v4l2_pipeline_inherit_controls);
+
+int v4l2_pipeline_inherit_controls(struct video_device *vfd,
+				   struct media_entity *start_entity)
+{
+	struct media_device *mdev = start_entity->graph_obj.mdev;
+	int ret;
+
+	mutex_lock(&mdev->graph_mutex);
+	ret = __v4l2_pipeline_inherit_controls(vfd, start_entity);
+	mutex_unlock(&mdev->graph_mutex);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(v4l2_pipeline_inherit_controls);
+
 /* -----------------------------------------------------------------------------
  * Pipeline power management
  *
diff --git a/include/media/v4l2-mc.h b/include/media/v4l2-mc.h
index 2634d9d..9848e77 100644
--- a/include/media/v4l2-mc.h
+++ b/include/media/v4l2-mc.h
@@ -171,6 +171,17 @@ void v4l_disable_media_source(struct video_device *vdev);
  */
 int v4l_vb2q_enable_media_source(struct vb2_queue *q);
 
+/**
+ * v4l2_pipeline_inherit_controls - Add the v4l2 controls from all
+ *				    subdev entities in a pipeline to
+ *				    the given video device.
+ * @vfd: the video device
+ * @start_entity: Starting entity
+ */
+int __v4l2_pipeline_inherit_controls(struct video_device *vfd,
+				     struct media_entity *start_entity);
+int v4l2_pipeline_inherit_controls(struct video_device *vfd,
+				   struct media_entity *start_entity);
 
 /**
  * v4l2_pipeline_pm_use - Update the use count of an entity
@@ -231,6 +242,20 @@ static inline int v4l_vb2q_enable_media_source(struct vb2_queue *q)
 	return 0;
 }
 
+static inline int __v4l2_pipeline_inherit_controls(
+	struct video_device *vfd,
+	struct media_entity *start_entity)
+{
+	return 0;
+}
+
+static inline int v4l2_pipeline_inherit_controls(
+	struct video_device *vfd,
+	struct media_entity *start_entity)
+{
+	return 0;
+}
+
 static inline int v4l2_pipeline_pm_use(struct media_entity *entity, int use)
 {
 	return 0;
-- 
2.7.4

[PATCH v5 17/39] [media] v4l2-mc: add a function to inherit controls from a pipeline

[Steve Longerbeam]

v4l2_pipeline_inherit_controls() will add the v4l2 controls from
all subdev entities in a pipeline to a given video device.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/media/v4l2-core/v4l2-mc.c | 48 +++++++++++++++++++++++++++++++++++++++
 include/media/v4l2-mc.h           | 25 ++++++++++++++++++++
 2 files changed, 73 insertions(+)

diff --git a/drivers/media/v4l2-core/v4l2-mc.c b/drivers/media/v4l2-core/v4l2-mc.c
index 303980b..09d4d97 100644
--- a/drivers/media/v4l2-core/v4l2-mc.c
+++ b/drivers/media/v4l2-core/v4l2-mc.c
@@ -22,6 +22,7 @@
 #include <linux/usb.h>
 #include <media/media-device.h>
 #include <media/media-entity.h>
+#include <media/v4l2-ctrls.h>
 #include <media/v4l2-fh.h>
 #include <media/v4l2-mc.h>
 #include <media/v4l2-subdev.h>
@@ -238,6 +239,53 @@ int v4l_vb2q_enable_media_source(struct vb2_queue *q)
 }
 EXPORT_SYMBOL_GPL(v4l_vb2q_enable_media_source);
 
+int __v4l2_pipeline_inherit_controls(struct video_device *vfd,
+				     struct media_entity *start_entity)
+{
+	struct media_device *mdev = start_entity->graph_obj.mdev;
+	struct media_entity *entity;
+	struct media_graph graph;
+	struct v4l2_subdev *sd;
+	int ret;
+
+	ret = media_graph_walk_init(&graph, mdev);
+	if (ret)
+		return ret;
+
+	media_graph_walk_start(&graph, start_entity);
+
+	while ((entity = media_graph_walk_next(&graph))) {
+		if (!is_media_entity_v4l2_subdev(entity))
+			continue;
+
+		sd = media_entity_to_v4l2_subdev(entity);
+
+		ret = v4l2_ctrl_add_handler(vfd->ctrl_handler,
+					    sd->ctrl_handler,
+					    NULL);
+		if (ret)
+			break;
+	}
+
+	media_graph_walk_cleanup(&graph);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(__v4l2_pipeline_inherit_controls);
+
+int v4l2_pipeline_inherit_controls(struct video_device *vfd,
+				   struct media_entity *start_entity)
+{
+	struct media_device *mdev = start_entity->graph_obj.mdev;
+	int ret;
+
+	mutex_lock(&mdev->graph_mutex);
+	ret = __v4l2_pipeline_inherit_controls(vfd, start_entity);
+	mutex_unlock(&mdev->graph_mutex);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(v4l2_pipeline_inherit_controls);
+
 /* -----------------------------------------------------------------------------
  * Pipeline power management
  *
diff --git a/include/media/v4l2-mc.h b/include/media/v4l2-mc.h
index 2634d9d..9848e77 100644
--- a/include/media/v4l2-mc.h
+++ b/include/media/v4l2-mc.h
@@ -171,6 +171,17 @@ void v4l_disable_media_source(struct video_device *vdev);
  */
 int v4l_vb2q_enable_media_source(struct vb2_queue *q);
 
+/**
+ * v4l2_pipeline_inherit_controls - Add the v4l2 controls from all
+ *				    subdev entities in a pipeline to
+ *				    the given video device.
+ * @vfd: the video device
+ * @start_entity: Starting entity
+ */
+int __v4l2_pipeline_inherit_controls(struct video_device *vfd,
+				     struct media_entity *start_entity);
+int v4l2_pipeline_inherit_controls(struct video_device *vfd,
+				   struct media_entity *start_entity);
 
 /**
  * v4l2_pipeline_pm_use - Update the use count of an entity
@@ -231,6 +242,20 @@ static inline int v4l_vb2q_enable_media_source(struct vb2_queue *q)
 	return 0;
 }
 
+static inline int __v4l2_pipeline_inherit_controls(
+	struct video_device *vfd,
+	struct media_entity *start_entity)
+{
+	return 0;
+}
+
+static inline int v4l2_pipeline_inherit_controls(
+	struct video_device *vfd,
+	struct media_entity *start_entity)
+{
+	return 0;
+}
+
 static inline int v4l2_pipeline_pm_use(struct media_entity *entity, int use)
 {
 	return 0;
-- 
2.7.4

Re: [PATCH v5 17/39] [media] v4l2-mc: add a function to inherit controls from a pipeline

[Hans Verkuil]

On 10/03/17 05:52, Steve Longerbeam wrote:
> v4l2_pipeline_inherit_controls() will add the v4l2 controls from
> all subdev entities in a pipeline to a given video device.
> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> ---
>  drivers/media/v4l2-core/v4l2-mc.c | 48 +++++++++++++++++++++++++++++++++++++++
>  include/media/v4l2-mc.h           | 25 ++++++++++++++++++++
>  2 files changed, 73 insertions(+)
> 
> diff --git a/drivers/media/v4l2-core/v4l2-mc.c b/drivers/media/v4l2-core/v4l2-mc.c
> index 303980b..09d4d97 100644
> --- a/drivers/media/v4l2-core/v4l2-mc.c
> +++ b/drivers/media/v4l2-core/v4l2-mc.c
> @@ -22,6 +22,7 @@
>  #include <linux/usb.h>
>  #include <media/media-device.h>
>  #include <media/media-entity.h>
> +#include <media/v4l2-ctrls.h>
>  #include <media/v4l2-fh.h>
>  #include <media/v4l2-mc.h>
>  #include <media/v4l2-subdev.h>
> @@ -238,6 +239,53 @@ int v4l_vb2q_enable_media_source(struct vb2_queue *q)
>  }
>  EXPORT_SYMBOL_GPL(v4l_vb2q_enable_media_source);
>  
> +int __v4l2_pipeline_inherit_controls(struct video_device *vfd,
> +				     struct media_entity *start_entity)
> +{
> +	struct media_device *mdev = start_entity->graph_obj.mdev;
> +	struct media_entity *entity;
> +	struct media_graph graph;
> +	struct v4l2_subdev *sd;
> +	int ret;
> +
> +	ret = media_graph_walk_init(&graph, mdev);
> +	if (ret)
> +		return ret;
> +
> +	media_graph_walk_start(&graph, start_entity);
> +
> +	while ((entity = media_graph_walk_next(&graph))) {
> +		if (!is_media_entity_v4l2_subdev(entity))
> +			continue;
> +
> +		sd = media_entity_to_v4l2_subdev(entity);
> +
> +		ret = v4l2_ctrl_add_handler(vfd->ctrl_handler,
> +					    sd->ctrl_handler,
> +					    NULL);
> +		if (ret)
> +			break;
> +	}
> +
> +	media_graph_walk_cleanup(&graph);
> +	return ret;
> +}
> +EXPORT_SYMBOL_GPL(__v4l2_pipeline_inherit_controls);
> +
> +int v4l2_pipeline_inherit_controls(struct video_device *vfd,
> +				   struct media_entity *start_entity)
> +{
> +	struct media_device *mdev = start_entity->graph_obj.mdev;
> +	int ret;
> +
> +	mutex_lock(&mdev->graph_mutex);
> +	ret = __v4l2_pipeline_inherit_controls(vfd, start_entity);
> +	mutex_unlock(&mdev->graph_mutex);
> +
> +	return ret;
> +}
> +EXPORT_SYMBOL_GPL(v4l2_pipeline_inherit_controls);
> +
>  /* -----------------------------------------------------------------------------
>   * Pipeline power management
>   *
> diff --git a/include/media/v4l2-mc.h b/include/media/v4l2-mc.h
> index 2634d9d..9848e77 100644
> --- a/include/media/v4l2-mc.h
> +++ b/include/media/v4l2-mc.h
> @@ -171,6 +171,17 @@ void v4l_disable_media_source(struct video_device *vdev);
>   */
>  int v4l_vb2q_enable_media_source(struct vb2_queue *q);
>  
> +/**
> + * v4l2_pipeline_inherit_controls - Add the v4l2 controls from all
> + *				    subdev entities in a pipeline to
> + *				    the given video device.
> + * @vfd: the video device
> + * @start_entity: Starting entity
> + */
> +int __v4l2_pipeline_inherit_controls(struct video_device *vfd,
> +				     struct media_entity *start_entity);
> +int v4l2_pipeline_inherit_controls(struct video_device *vfd,
> +				   struct media_entity *start_entity);

Please document which is the unlocked variant and which lock the locked
variant takes.

Regards,

	Hans

>  
>  /**
>   * v4l2_pipeline_pm_use - Update the use count of an entity
> @@ -231,6 +242,20 @@ static inline int v4l_vb2q_enable_media_source(struct vb2_queue *q)
>  	return 0;
>  }
>  
> +static inline int __v4l2_pipeline_inherit_controls(
> +	struct video_device *vfd,
> +	struct media_entity *start_entity)
> +{
> +	return 0;
> +}
> +
> +static inline int v4l2_pipeline_inherit_controls(
> +	struct video_device *vfd,
> +	struct media_entity *start_entity)
> +{
> +	return 0;
> +}
> +
>  static inline int v4l2_pipeline_pm_use(struct media_entity *entity, int use)
>  {
>  	return 0;
> 

[PATCH v5 17/39] [media] v4l2-mc: add a function to inherit controls from a pipeline

[Hans Verkuil]

On 10/03/17 05:52, Steve Longerbeam wrote:
> v4l2_pipeline_inherit_controls() will add the v4l2 controls from
> all subdev entities in a pipeline to a given video device.
> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> ---
>  drivers/media/v4l2-core/v4l2-mc.c | 48 +++++++++++++++++++++++++++++++++++++++
>  include/media/v4l2-mc.h           | 25 ++++++++++++++++++++
>  2 files changed, 73 insertions(+)
> 
> diff --git a/drivers/media/v4l2-core/v4l2-mc.c b/drivers/media/v4l2-core/v4l2-mc.c
> index 303980b..09d4d97 100644
> --- a/drivers/media/v4l2-core/v4l2-mc.c
> +++ b/drivers/media/v4l2-core/v4l2-mc.c
> @@ -22,6 +22,7 @@
>  #include <linux/usb.h>
>  #include <media/media-device.h>
>  #include <media/media-entity.h>
> +#include <media/v4l2-ctrls.h>
>  #include <media/v4l2-fh.h>
>  #include <media/v4l2-mc.h>
>  #include <media/v4l2-subdev.h>
> @@ -238,6 +239,53 @@ int v4l_vb2q_enable_media_source(struct vb2_queue *q)
>  }
>  EXPORT_SYMBOL_GPL(v4l_vb2q_enable_media_source);
>  
> +int __v4l2_pipeline_inherit_controls(struct video_device *vfd,
> +				     struct media_entity *start_entity)
> +{
> +	struct media_device *mdev = start_entity->graph_obj.mdev;
> +	struct media_entity *entity;
> +	struct media_graph graph;
> +	struct v4l2_subdev *sd;
> +	int ret;
> +
> +	ret = media_graph_walk_init(&graph, mdev);
> +	if (ret)
> +		return ret;
> +
> +	media_graph_walk_start(&graph, start_entity);
> +
> +	while ((entity = media_graph_walk_next(&graph))) {
> +		if (!is_media_entity_v4l2_subdev(entity))
> +			continue;
> +
> +		sd = media_entity_to_v4l2_subdev(entity);
> +
> +		ret = v4l2_ctrl_add_handler(vfd->ctrl_handler,
> +					    sd->ctrl_handler,
> +					    NULL);
> +		if (ret)
> +			break;
> +	}
> +
> +	media_graph_walk_cleanup(&graph);
> +	return ret;
> +}
> +EXPORT_SYMBOL_GPL(__v4l2_pipeline_inherit_controls);
> +
> +int v4l2_pipeline_inherit_controls(struct video_device *vfd,
> +				   struct media_entity *start_entity)
> +{
> +	struct media_device *mdev = start_entity->graph_obj.mdev;
> +	int ret;
> +
> +	mutex_lock(&mdev->graph_mutex);
> +	ret = __v4l2_pipeline_inherit_controls(vfd, start_entity);
> +	mutex_unlock(&mdev->graph_mutex);
> +
> +	return ret;
> +}
> +EXPORT_SYMBOL_GPL(v4l2_pipeline_inherit_controls);
> +
>  /* -----------------------------------------------------------------------------
>   * Pipeline power management
>   *
> diff --git a/include/media/v4l2-mc.h b/include/media/v4l2-mc.h
> index 2634d9d..9848e77 100644
> --- a/include/media/v4l2-mc.h
> +++ b/include/media/v4l2-mc.h
> @@ -171,6 +171,17 @@ void v4l_disable_media_source(struct video_device *vdev);
>   */
>  int v4l_vb2q_enable_media_source(struct vb2_queue *q);
>  
> +/**
> + * v4l2_pipeline_inherit_controls - Add the v4l2 controls from all
> + *				    subdev entities in a pipeline to
> + *				    the given video device.
> + * @vfd: the video device
> + * @start_entity: Starting entity
> + */
> +int __v4l2_pipeline_inherit_controls(struct video_device *vfd,
> +				     struct media_entity *start_entity);
> +int v4l2_pipeline_inherit_controls(struct video_device *vfd,
> +				   struct media_entity *start_entity);

Please document which is the unlocked variant and which lock the locked
variant takes.

Regards,

	Hans

>  
>  /**
>   * v4l2_pipeline_pm_use - Update the use count of an entity
> @@ -231,6 +242,20 @@ static inline int v4l_vb2q_enable_media_source(struct vb2_queue *q)
>  	return 0;
>  }
>  
> +static inline int __v4l2_pipeline_inherit_controls(
> +	struct video_device *vfd,
> +	struct media_entity *start_entity)
> +{
> +	return 0;
> +}
> +
> +static inline int v4l2_pipeline_inherit_controls(
> +	struct video_device *vfd,
> +	struct media_entity *start_entity)
> +{
> +	return 0;
> +}
> +
>  static inline int v4l2_pipeline_pm_use(struct media_entity *entity, int use)
>  {
>  	return 0;
> 

Re: [PATCH v5 17/39] [media] v4l2-mc: add a function to inherit controls from a pipeline

[Hans Verkuil]

On 10/03/17 05:52, Steve Longerbeam wrote:
> v4l2_pipeline_inherit_controls() will add the v4l2 controls from
> all subdev entities in a pipeline to a given video device.
> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> ---
>  drivers/media/v4l2-core/v4l2-mc.c | 48 +++++++++++++++++++++++++++++++++++++++
>  include/media/v4l2-mc.h           | 25 ++++++++++++++++++++
>  2 files changed, 73 insertions(+)
> 
> diff --git a/drivers/media/v4l2-core/v4l2-mc.c b/drivers/media/v4l2-core/v4l2-mc.c
> index 303980b..09d4d97 100644
> --- a/drivers/media/v4l2-core/v4l2-mc.c
> +++ b/drivers/media/v4l2-core/v4l2-mc.c
> @@ -22,6 +22,7 @@
>  #include <linux/usb.h>
>  #include <media/media-device.h>
>  #include <media/media-entity.h>
> +#include <media/v4l2-ctrls.h>
>  #include <media/v4l2-fh.h>
>  #include <media/v4l2-mc.h>
>  #include <media/v4l2-subdev.h>
> @@ -238,6 +239,53 @@ int v4l_vb2q_enable_media_source(struct vb2_queue *q)
>  }
>  EXPORT_SYMBOL_GPL(v4l_vb2q_enable_media_source);
>  
> +int __v4l2_pipeline_inherit_controls(struct video_device *vfd,
> +				     struct media_entity *start_entity)
> +{
> +	struct media_device *mdev = start_entity->graph_obj.mdev;
> +	struct media_entity *entity;
> +	struct media_graph graph;
> +	struct v4l2_subdev *sd;
> +	int ret;
> +
> +	ret = media_graph_walk_init(&graph, mdev);
> +	if (ret)
> +		return ret;
> +
> +	media_graph_walk_start(&graph, start_entity);
> +
> +	while ((entity = media_graph_walk_next(&graph))) {
> +		if (!is_media_entity_v4l2_subdev(entity))
> +			continue;
> +
> +		sd = media_entity_to_v4l2_subdev(entity);
> +
> +		ret = v4l2_ctrl_add_handler(vfd->ctrl_handler,
> +					    sd->ctrl_handler,
> +					    NULL);
> +		if (ret)
> +			break;
> +	}
> +
> +	media_graph_walk_cleanup(&graph);
> +	return ret;
> +}
> +EXPORT_SYMBOL_GPL(__v4l2_pipeline_inherit_controls);
> +
> +int v4l2_pipeline_inherit_controls(struct video_device *vfd,
> +				   struct media_entity *start_entity)
> +{
> +	struct media_device *mdev = start_entity->graph_obj.mdev;
> +	int ret;
> +
> +	mutex_lock(&mdev->graph_mutex);
> +	ret = __v4l2_pipeline_inherit_controls(vfd, start_entity);
> +	mutex_unlock(&mdev->graph_mutex);
> +
> +	return ret;
> +}
> +EXPORT_SYMBOL_GPL(v4l2_pipeline_inherit_controls);
> +
>  /* -----------------------------------------------------------------------------
>   * Pipeline power management
>   *
> diff --git a/include/media/v4l2-mc.h b/include/media/v4l2-mc.h
> index 2634d9d..9848e77 100644
> --- a/include/media/v4l2-mc.h
> +++ b/include/media/v4l2-mc.h
> @@ -171,6 +171,17 @@ void v4l_disable_media_source(struct video_device *vdev);
>   */
>  int v4l_vb2q_enable_media_source(struct vb2_queue *q);
>  
> +/**
> + * v4l2_pipeline_inherit_controls - Add the v4l2 controls from all
> + *				    subdev entities in a pipeline to
> + *				    the given video device.
> + * @vfd: the video device
> + * @start_entity: Starting entity
> + */
> +int __v4l2_pipeline_inherit_controls(struct video_device *vfd,
> +				     struct media_entity *start_entity);
> +int v4l2_pipeline_inherit_controls(struct video_device *vfd,
> +				   struct media_entity *start_entity);

Please document which is the unlocked variant and which lock the locked
variant takes.

Regards,

	Hans

>  
>  /**
>   * v4l2_pipeline_pm_use - Update the use count of an entity
> @@ -231,6 +242,20 @@ static inline int v4l_vb2q_enable_media_source(struct vb2_queue *q)
>  	return 0;
>  }
>  
> +static inline int __v4l2_pipeline_inherit_controls(
> +	struct video_device *vfd,
> +	struct media_entity *start_entity)
> +{
> +	return 0;
> +}
> +
> +static inline int v4l2_pipeline_inherit_controls(
> +	struct video_device *vfd,
> +	struct media_entity *start_entity)
> +{
> +	return 0;
> +}
> +
>  static inline int v4l2_pipeline_pm_use(struct media_entity *entity, int use)
>  {
>  	return 0;
> 

[PATCH v5 18/39] [media] v4l: subdev: Add function to validate frame interval

[Steve Longerbeam]

If the pads on both sides of a link specify a frame interval, then
those frame intervals should match. Create the exported function
v4l2_subdev_link_validate_frame_interval() to verify this. This
function can be called in a subdevice's media_entity_operations
or v4l2_subdev_pad_ops link_validate callbacks.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/media/v4l2-core/v4l2-subdev.c | 50 +++++++++++++++++++++++++++++++++++
 include/media/v4l2-subdev.h           | 10 +++++++
 2 files changed, 60 insertions(+)

diff --git a/drivers/media/v4l2-core/v4l2-subdev.c b/drivers/media/v4l2-core/v4l2-subdev.c
index da78497..7a0f387 100644
--- a/drivers/media/v4l2-core/v4l2-subdev.c
+++ b/drivers/media/v4l2-core/v4l2-subdev.c
@@ -521,6 +521,25 @@ int v4l2_subdev_link_validate_default(struct v4l2_subdev *sd,
 EXPORT_SYMBOL_GPL(v4l2_subdev_link_validate_default);
 
 static int
+v4l2_subdev_link_validate_get_fi(struct media_pad *pad,
+				 struct v4l2_subdev_frame_interval *fi)
+{
+	if (is_media_entity_v4l2_subdev(pad->entity)) {
+		struct v4l2_subdev *sd =
+			media_entity_to_v4l2_subdev(pad->entity);
+
+		fi->pad = pad->index;
+		return v4l2_subdev_call(sd, video, g_frame_interval, fi);
+	}
+
+	WARN(pad->entity->function != MEDIA_ENT_F_IO_V4L,
+	     "Driver bug! Wrong media entity type 0x%08x, entity %s\n",
+	     pad->entity->function, pad->entity->name);
+
+	return -EINVAL;
+}
+
+static int
 v4l2_subdev_link_validate_get_format(struct media_pad *pad,
 				     struct v4l2_subdev_format *fmt)
 {
@@ -540,6 +559,37 @@ v4l2_subdev_link_validate_get_format(struct media_pad *pad,
 	return -EINVAL;
 }
 
+int v4l2_subdev_link_validate_frame_interval(struct media_link *link)
+{
+	struct v4l2_subdev_frame_interval src_fi, sink_fi;
+	unsigned long src_usec, sink_usec;
+	int rval;
+
+	rval = v4l2_subdev_link_validate_get_fi(link->source, &src_fi);
+	if (rval < 0)
+		return 0;
+
+	rval = v4l2_subdev_link_validate_get_fi(link->sink, &sink_fi);
+	if (rval < 0)
+		return 0;
+
+	if (src_fi.interval.numerator == 0   ||
+	    src_fi.interval.denominator == 0 ||
+	    sink_fi.interval.numerator == 0  ||
+	    sink_fi.interval.denominator == 0)
+		return -EPIPE;
+
+	src_usec = DIV_ROUND_CLOSEST_ULL(
+		(u64)src_fi.interval.numerator * USEC_PER_SEC,
+		src_fi.interval.denominator);
+	sink_usec = DIV_ROUND_CLOSEST_ULL(
+		(u64)sink_fi.interval.numerator * USEC_PER_SEC,
+		sink_fi.interval.denominator);
+
+	return (src_usec != sink_usec) ? -EPIPE : 0;
+}
+EXPORT_SYMBOL_GPL(v4l2_subdev_link_validate_frame_interval);
+
 int v4l2_subdev_link_validate(struct media_link *link)
 {
 	struct v4l2_subdev *sink;
diff --git a/include/media/v4l2-subdev.h b/include/media/v4l2-subdev.h
index 0ab1c5d..60c941d 100644
--- a/include/media/v4l2-subdev.h
+++ b/include/media/v4l2-subdev.h
@@ -929,6 +929,16 @@ int v4l2_subdev_link_validate_default(struct v4l2_subdev *sd,
 				      struct v4l2_subdev_format *sink_fmt);
 
 /**
+ * v4l2_subdev_link_validate_frame_interval - validates a media link
+ *
+ * @link: pointer to &struct media_link
+ *
+ * This function ensures that the frame intervals, if specified by
+ * both the source and sink subdevs of the link, are equal.
+ */
+int v4l2_subdev_link_validate_frame_interval(struct media_link *link);
+
+/**
  * v4l2_subdev_link_validate - validates a media link
  *
  * @link: pointer to &struct media_link
-- 
2.7.4

[PATCH v5 18/39] [media] v4l: subdev: Add function to validate frame interval

[Steve Longerbeam]

If the pads on both sides of a link specify a frame interval, then
those frame intervals should match. Create the exported function
v4l2_subdev_link_validate_frame_interval() to verify this. This
function can be called in a subdevice's media_entity_operations
or v4l2_subdev_pad_ops link_validate callbacks.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/media/v4l2-core/v4l2-subdev.c | 50 +++++++++++++++++++++++++++++++++++
 include/media/v4l2-subdev.h           | 10 +++++++
 2 files changed, 60 insertions(+)

diff --git a/drivers/media/v4l2-core/v4l2-subdev.c b/drivers/media/v4l2-core/v4l2-subdev.c
index da78497..7a0f387 100644
--- a/drivers/media/v4l2-core/v4l2-subdev.c
+++ b/drivers/media/v4l2-core/v4l2-subdev.c
@@ -521,6 +521,25 @@ int v4l2_subdev_link_validate_default(struct v4l2_subdev *sd,
 EXPORT_SYMBOL_GPL(v4l2_subdev_link_validate_default);
 
 static int
+v4l2_subdev_link_validate_get_fi(struct media_pad *pad,
+				 struct v4l2_subdev_frame_interval *fi)
+{
+	if (is_media_entity_v4l2_subdev(pad->entity)) {
+		struct v4l2_subdev *sd =
+			media_entity_to_v4l2_subdev(pad->entity);
+
+		fi->pad = pad->index;
+		return v4l2_subdev_call(sd, video, g_frame_interval, fi);
+	}
+
+	WARN(pad->entity->function != MEDIA_ENT_F_IO_V4L,
+	     "Driver bug! Wrong media entity type 0x%08x, entity %s\n",
+	     pad->entity->function, pad->entity->name);
+
+	return -EINVAL;
+}
+
+static int
 v4l2_subdev_link_validate_get_format(struct media_pad *pad,
 				     struct v4l2_subdev_format *fmt)
 {
@@ -540,6 +559,37 @@ v4l2_subdev_link_validate_get_format(struct media_pad *pad,
 	return -EINVAL;
 }
 
+int v4l2_subdev_link_validate_frame_interval(struct media_link *link)
+{
+	struct v4l2_subdev_frame_interval src_fi, sink_fi;
+	unsigned long src_usec, sink_usec;
+	int rval;
+
+	rval = v4l2_subdev_link_validate_get_fi(link->source, &src_fi);
+	if (rval < 0)
+		return 0;
+
+	rval = v4l2_subdev_link_validate_get_fi(link->sink, &sink_fi);
+	if (rval < 0)
+		return 0;
+
+	if (src_fi.interval.numerator == 0   ||
+	    src_fi.interval.denominator == 0 ||
+	    sink_fi.interval.numerator == 0  ||
+	    sink_fi.interval.denominator == 0)
+		return -EPIPE;
+
+	src_usec = DIV_ROUND_CLOSEST_ULL(
+		(u64)src_fi.interval.numerator * USEC_PER_SEC,
+		src_fi.interval.denominator);
+	sink_usec = DIV_ROUND_CLOSEST_ULL(
+		(u64)sink_fi.interval.numerator * USEC_PER_SEC,
+		sink_fi.interval.denominator);
+
+	return (src_usec != sink_usec) ? -EPIPE : 0;
+}
+EXPORT_SYMBOL_GPL(v4l2_subdev_link_validate_frame_interval);
+
 int v4l2_subdev_link_validate(struct media_link *link)
 {
 	struct v4l2_subdev *sink;
diff --git a/include/media/v4l2-subdev.h b/include/media/v4l2-subdev.h
index 0ab1c5d..60c941d 100644
--- a/include/media/v4l2-subdev.h
+++ b/include/media/v4l2-subdev.h
@@ -929,6 +929,16 @@ int v4l2_subdev_link_validate_default(struct v4l2_subdev *sd,
 				      struct v4l2_subdev_format *sink_fmt);
 
 /**
+ * v4l2_subdev_link_validate_frame_interval - validates a media link
+ *
+ * @link: pointer to &struct media_link
+ *
+ * This function ensures that the frame intervals, if specified by
+ * both the source and sink subdevs of the link, are equal.
+ */
+int v4l2_subdev_link_validate_frame_interval(struct media_link *link);
+
+/**
  * v4l2_subdev_link_validate - validates a media link
  *
  * @link: pointer to &struct media_link
-- 
2.7.4

[PATCH v5 18/39] [media] v4l: subdev: Add function to validate frame interval

[Steve Longerbeam]

If the pads on both sides of a link specify a frame interval, then
those frame intervals should match. Create the exported function
v4l2_subdev_link_validate_frame_interval() to verify this. This
function can be called in a subdevice's media_entity_operations
or v4l2_subdev_pad_ops link_validate callbacks.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/media/v4l2-core/v4l2-subdev.c | 50 +++++++++++++++++++++++++++++++++++
 include/media/v4l2-subdev.h           | 10 +++++++
 2 files changed, 60 insertions(+)

diff --git a/drivers/media/v4l2-core/v4l2-subdev.c b/drivers/media/v4l2-core/v4l2-subdev.c
index da78497..7a0f387 100644
--- a/drivers/media/v4l2-core/v4l2-subdev.c
+++ b/drivers/media/v4l2-core/v4l2-subdev.c
@@ -521,6 +521,25 @@ int v4l2_subdev_link_validate_default(struct v4l2_subdev *sd,
 EXPORT_SYMBOL_GPL(v4l2_subdev_link_validate_default);
 
 static int
+v4l2_subdev_link_validate_get_fi(struct media_pad *pad,
+				 struct v4l2_subdev_frame_interval *fi)
+{
+	if (is_media_entity_v4l2_subdev(pad->entity)) {
+		struct v4l2_subdev *sd =
+			media_entity_to_v4l2_subdev(pad->entity);
+
+		fi->pad = pad->index;
+		return v4l2_subdev_call(sd, video, g_frame_interval, fi);
+	}
+
+	WARN(pad->entity->function != MEDIA_ENT_F_IO_V4L,
+	     "Driver bug! Wrong media entity type 0x%08x, entity %s\n",
+	     pad->entity->function, pad->entity->name);
+
+	return -EINVAL;
+}
+
+static int
 v4l2_subdev_link_validate_get_format(struct media_pad *pad,
 				     struct v4l2_subdev_format *fmt)
 {
@@ -540,6 +559,37 @@ v4l2_subdev_link_validate_get_format(struct media_pad *pad,
 	return -EINVAL;
 }
 
+int v4l2_subdev_link_validate_frame_interval(struct media_link *link)
+{
+	struct v4l2_subdev_frame_interval src_fi, sink_fi;
+	unsigned long src_usec, sink_usec;
+	int rval;
+
+	rval = v4l2_subdev_link_validate_get_fi(link->source, &src_fi);
+	if (rval < 0)
+		return 0;
+
+	rval = v4l2_subdev_link_validate_get_fi(link->sink, &sink_fi);
+	if (rval < 0)
+		return 0;
+
+	if (src_fi.interval.numerator == 0   ||
+	    src_fi.interval.denominator == 0 ||
+	    sink_fi.interval.numerator == 0  ||
+	    sink_fi.interval.denominator == 0)
+		return -EPIPE;
+
+	src_usec = DIV_ROUND_CLOSEST_ULL(
+		(u64)src_fi.interval.numerator * USEC_PER_SEC,
+		src_fi.interval.denominator);
+	sink_usec = DIV_ROUND_CLOSEST_ULL(
+		(u64)sink_fi.interval.numerator * USEC_PER_SEC,
+		sink_fi.interval.denominator);
+
+	return (src_usec != sink_usec) ? -EPIPE : 0;
+}
+EXPORT_SYMBOL_GPL(v4l2_subdev_link_validate_frame_interval);
+
 int v4l2_subdev_link_validate(struct media_link *link)
 {
 	struct v4l2_subdev *sink;
diff --git a/include/media/v4l2-subdev.h b/include/media/v4l2-subdev.h
index 0ab1c5d..60c941d 100644
--- a/include/media/v4l2-subdev.h
+++ b/include/media/v4l2-subdev.h
@@ -929,6 +929,16 @@ int v4l2_subdev_link_validate_default(struct v4l2_subdev *sd,
 				      struct v4l2_subdev_format *sink_fmt);
 
 /**
+ * v4l2_subdev_link_validate_frame_interval - validates a media link
+ *
+ * @link: pointer to &struct media_link
+ *
+ * This function ensures that the frame intervals, if specified by
+ * both the source and sink subdevs of the link, are equal.
+ */
+int v4l2_subdev_link_validate_frame_interval(struct media_link *link);
+
+/**
  * v4l2_subdev_link_validate - validates a media link
  *
  * @link: pointer to &struct media_link
-- 
2.7.4

Re: [PATCH v5 18/39] [media] v4l: subdev: Add function to validate frame interval

[Sakari Ailus]

Hi Steve,

On Thu, Mar 09, 2017 at 08:52:58PM -0800, Steve Longerbeam wrote:
> If the pads on both sides of a link specify a frame interval, then
> those frame intervals should match. Create the exported function
> v4l2_subdev_link_validate_frame_interval() to verify this. This
> function can be called in a subdevice's media_entity_operations
> or v4l2_subdev_pad_ops link_validate callbacks.
> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>

If your only goal is to configure frame dropping on a sub-device, I suggest
to implement s_frame_interval() on the pads of that sub-device only. The
frames are then dropped according to the configured frame rates between the
sink and source pads. Say, configuring sink for 1/30 s and source 1/15 would
drop half of the incoming frames.

Considering that supporting specific frame interval on most sub-devices adds
no value or is not the interface through which it the frame rate configured,
I think it is overkill to change the link validation to expect otherwise.

-- 
Kind regards,

Sakari Ailus
e-mail: sakari.ailus@iki.fi	XMPP: sailus@retiisi.org.uk

[PATCH v5 18/39] [media] v4l: subdev: Add function to validate frame interval

[Sakari Ailus]

Hi Steve,

On Thu, Mar 09, 2017 at 08:52:58PM -0800, Steve Longerbeam wrote:
> If the pads on both sides of a link specify a frame interval, then
> those frame intervals should match. Create the exported function
> v4l2_subdev_link_validate_frame_interval() to verify this. This
> function can be called in a subdevice's media_entity_operations
> or v4l2_subdev_pad_ops link_validate callbacks.
> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>

If your only goal is to configure frame dropping on a sub-device, I suggest
to implement s_frame_interval() on the pads of that sub-device only. The
frames are then dropped according to the configured frame rates between the
sink and source pads. Say, configuring sink for 1/30 s and source 1/15 would
drop half of the incoming frames.

Considering that supporting specific frame interval on most sub-devices adds
no value or is not the interface through which it the frame rate configured,
I think it is overkill to change the link validation to expect otherwise.

-- 
Kind regards,

Sakari Ailus
e-mail: sakari.ailus at iki.fi	XMPP: sailus at retiisi.org.uk

Re: [PATCH v5 18/39] [media] v4l: subdev: Add function to validate frame interval

[Sakari Ailus]

Hi Steve,

On Thu, Mar 09, 2017 at 08:52:58PM -0800, Steve Longerbeam wrote:
> If the pads on both sides of a link specify a frame interval, then
> those frame intervals should match. Create the exported function
> v4l2_subdev_link_validate_frame_interval() to verify this. This
> function can be called in a subdevice's media_entity_operations
> or v4l2_subdev_pad_ops link_validate callbacks.
> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam-nmGgyN9QBj3QT0dZR+AlfA@public.gmane.org>

If your only goal is to configure frame dropping on a sub-device, I suggest
to implement s_frame_interval() on the pads of that sub-device only. The
frames are then dropped according to the configured frame rates between the
sink and source pads. Say, configuring sink for 1/30 s and source 1/15 would
drop half of the incoming frames.

Considering that supporting specific frame interval on most sub-devices adds
no value or is not the interface through which it the frame rate configured,
I think it is overkill to change the link validation to expect otherwise.

-- 
Kind regards,

Sakari Ailus
e-mail: sakari.ailus-X3B1VOXEql0@public.gmane.org	XMPP: sailus-PCDdDYkjdNMDXYZnReoRVg@public.gmane.org
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 18/39] [media] v4l: subdev: Add function to validate frame interval

[Steve Longerbeam]

On 03/11/2017 05:41 AM, Sakari Ailus wrote:
> Hi Steve,
>
> On Thu, Mar 09, 2017 at 08:52:58PM -0800, Steve Longerbeam wrote:
>> If the pads on both sides of a link specify a frame interval, then
>> those frame intervals should match. Create the exported function
>> v4l2_subdev_link_validate_frame_interval() to verify this. This
>> function can be called in a subdevice's media_entity_operations
>> or v4l2_subdev_pad_ops link_validate callbacks.
>>
>> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
>
> If your only goal is to configure frame dropping on a sub-device, I suggest
> to implement s_frame_interval() on the pads of that sub-device only. The
> frames are then dropped according to the configured frame rates between the
> sink and source pads. Say, configuring sink for 1/30 s and source 1/15 would
> drop half of the incoming frames.
>
> Considering that supporting specific frame interval on most sub-devices adds
> no value or is not the interface through which it the frame rate configured,
> I think it is overkill to change the link validation to expect otherwise.


Well, while I think this function might still have validity in the 
future, I do agree with you that a subdev that has no control over
frame rate has no business implementing the get|set ops.

In the imx-media subdevs, the only one that can affect frame rate (via
frame skipping) is the CSI. So I'll go ahead and remove the
[gs]_frame_interval ops from the others. I can remove this patch as
a result.


Steve

[PATCH v5 18/39] [media] v4l: subdev: Add function to validate frame interval

[Steve Longerbeam]

On 03/11/2017 05:41 AM, Sakari Ailus wrote:
> Hi Steve,
>
> On Thu, Mar 09, 2017 at 08:52:58PM -0800, Steve Longerbeam wrote:
>> If the pads on both sides of a link specify a frame interval, then
>> those frame intervals should match. Create the exported function
>> v4l2_subdev_link_validate_frame_interval() to verify this. This
>> function can be called in a subdevice's media_entity_operations
>> or v4l2_subdev_pad_ops link_validate callbacks.
>>
>> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
>
> If your only goal is to configure frame dropping on a sub-device, I suggest
> to implement s_frame_interval() on the pads of that sub-device only. The
> frames are then dropped according to the configured frame rates between the
> sink and source pads. Say, configuring sink for 1/30 s and source 1/15 would
> drop half of the incoming frames.
>
> Considering that supporting specific frame interval on most sub-devices adds
> no value or is not the interface through which it the frame rate configured,
> I think it is overkill to change the link validation to expect otherwise.


Well, while I think this function might still have validity in the 
future, I do agree with you that a subdev that has no control over
frame rate has no business implementing the get|set ops.

In the imx-media subdevs, the only one that can affect frame rate (via
frame skipping) is the CSI. So I'll go ahead and remove the
[gs]_frame_interval ops from the others. I can remove this patch as
a result.


Steve

Re: [PATCH v5 18/39] [media] v4l: subdev: Add function to validate frame interval

[Steve Longerbeam]

On 03/11/2017 05:41 AM, Sakari Ailus wrote:
> Hi Steve,
>
> On Thu, Mar 09, 2017 at 08:52:58PM -0800, Steve Longerbeam wrote:
>> If the pads on both sides of a link specify a frame interval, then
>> those frame intervals should match. Create the exported function
>> v4l2_subdev_link_validate_frame_interval() to verify this. This
>> function can be called in a subdevice's media_entity_operations
>> or v4l2_subdev_pad_ops link_validate callbacks.
>>
>> Signed-off-by: Steve Longerbeam <steve_longerbeam-nmGgyN9QBj3QT0dZR+AlfA@public.gmane.org>
>
> If your only goal is to configure frame dropping on a sub-device, I suggest
> to implement s_frame_interval() on the pads of that sub-device only. The
> frames are then dropped according to the configured frame rates between the
> sink and source pads. Say, configuring sink for 1/30 s and source 1/15 would
> drop half of the incoming frames.
>
> Considering that supporting specific frame interval on most sub-devices adds
> no value or is not the interface through which it the frame rate configured,
> I think it is overkill to change the link validation to expect otherwise.


Well, while I think this function might still have validity in the 
future, I do agree with you that a subdev that has no control over
frame rate has no business implementing the get|set ops.

In the imx-media subdevs, the only one that can affect frame rate (via
frame skipping) is the CSI. So I'll go ahead and remove the
[gs]_frame_interval ops from the others. I can remove this patch as
a result.


Steve
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 18/39] [media] v4l: subdev: Add function to validate frame interval

[Sakari Ailus]

On Sat, Mar 11, 2017 at 12:31:24PM -0800, Steve Longerbeam wrote:
> 
> 
> On 03/11/2017 05:41 AM, Sakari Ailus wrote:
> >Hi Steve,
> >
> >On Thu, Mar 09, 2017 at 08:52:58PM -0800, Steve Longerbeam wrote:
> >>If the pads on both sides of a link specify a frame interval, then
> >>those frame intervals should match. Create the exported function
> >>v4l2_subdev_link_validate_frame_interval() to verify this. This
> >>function can be called in a subdevice's media_entity_operations
> >>or v4l2_subdev_pad_ops link_validate callbacks.
> >>
> >>Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> >
> >If your only goal is to configure frame dropping on a sub-device, I suggest
> >to implement s_frame_interval() on the pads of that sub-device only. The
> >frames are then dropped according to the configured frame rates between the
> >sink and source pads. Say, configuring sink for 1/30 s and source 1/15 would
> >drop half of the incoming frames.
> >
> >Considering that supporting specific frame interval on most sub-devices adds
> >no value or is not the interface through which it the frame rate configured,
> >I think it is overkill to change the link validation to expect otherwise.
> 
> 
> Well, while I think this function might still have validity in the future, I
> do agree with you that a subdev that has no control over
> frame rate has no business implementing the get|set ops.
> 
> In the imx-media subdevs, the only one that can affect frame rate (via
> frame skipping) is the CSI. So I'll go ahead and remove the
> [gs]_frame_interval ops from the others. I can remove this patch as
> a result.

Agreed.

-- 
Sakari Ailus
e-mail: sakari.ailus@iki.fi	XMPP: sailus@retiisi.org.uk

[PATCH v5 18/39] [media] v4l: subdev: Add function to validate frame interval

[Sakari Ailus]

On Sat, Mar 11, 2017 at 12:31:24PM -0800, Steve Longerbeam wrote:
> 
> 
> On 03/11/2017 05:41 AM, Sakari Ailus wrote:
> >Hi Steve,
> >
> >On Thu, Mar 09, 2017 at 08:52:58PM -0800, Steve Longerbeam wrote:
> >>If the pads on both sides of a link specify a frame interval, then
> >>those frame intervals should match. Create the exported function
> >>v4l2_subdev_link_validate_frame_interval() to verify this. This
> >>function can be called in a subdevice's media_entity_operations
> >>or v4l2_subdev_pad_ops link_validate callbacks.
> >>
> >>Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> >
> >If your only goal is to configure frame dropping on a sub-device, I suggest
> >to implement s_frame_interval() on the pads of that sub-device only. The
> >frames are then dropped according to the configured frame rates between the
> >sink and source pads. Say, configuring sink for 1/30 s and source 1/15 would
> >drop half of the incoming frames.
> >
> >Considering that supporting specific frame interval on most sub-devices adds
> >no value or is not the interface through which it the frame rate configured,
> >I think it is overkill to change the link validation to expect otherwise.
> 
> 
> Well, while I think this function might still have validity in the future, I
> do agree with you that a subdev that has no control over
> frame rate has no business implementing the get|set ops.
> 
> In the imx-media subdevs, the only one that can affect frame rate (via
> frame skipping) is the CSI. So I'll go ahead and remove the
> [gs]_frame_interval ops from the others. I can remove this patch as
> a result.

Agreed.

-- 
Sakari Ailus
e-mail: sakari.ailus at iki.fi	XMPP: sailus at retiisi.org.uk

Re: [PATCH v5 18/39] [media] v4l: subdev: Add function to validate frame interval

[Sakari Ailus]

On Sat, Mar 11, 2017 at 12:31:24PM -0800, Steve Longerbeam wrote:
> 
> 
> On 03/11/2017 05:41 AM, Sakari Ailus wrote:
> >Hi Steve,
> >
> >On Thu, Mar 09, 2017 at 08:52:58PM -0800, Steve Longerbeam wrote:
> >>If the pads on both sides of a link specify a frame interval, then
> >>those frame intervals should match. Create the exported function
> >>v4l2_subdev_link_validate_frame_interval() to verify this. This
> >>function can be called in a subdevice's media_entity_operations
> >>or v4l2_subdev_pad_ops link_validate callbacks.
> >>
> >>Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
> >
> >If your only goal is to configure frame dropping on a sub-device, I suggest
> >to implement s_frame_interval() on the pads of that sub-device only. The
> >frames are then dropped according to the configured frame rates between the
> >sink and source pads. Say, configuring sink for 1/30 s and source 1/15 would
> >drop half of the incoming frames.
> >
> >Considering that supporting specific frame interval on most sub-devices adds
> >no value or is not the interface through which it the frame rate configured,
> >I think it is overkill to change the link validation to expect otherwise.
> 
> 
> Well, while I think this function might still have validity in the future, I
> do agree with you that a subdev that has no control over
> frame rate has no business implementing the get|set ops.
> 
> In the imx-media subdevs, the only one that can affect frame rate (via
> frame skipping) is the CSI. So I'll go ahead and remove the
> [gs]_frame_interval ops from the others. I can remove this patch as
> a result.

Agreed.

-- 
Sakari Ailus
e-mail: sakari.ailus@iki.fi	XMPP: sailus@retiisi.org.uk

[PATCH v5 19/39] [media] add Omnivision OV5640 sensor driver

[Steve Longerbeam]

This driver is based on ov5640_mipi.c from Freescale imx_3.10.17_1.0.0_beta
branch, modified heavily to bring forward to latest interfaces and code
cleanup.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/media/i2c/Kconfig  |    7 +
 drivers/media/i2c/Makefile |    1 +
 drivers/media/i2c/ov5640.c | 2231 ++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 2239 insertions(+)
 create mode 100644 drivers/media/i2c/ov5640.c

diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index cee1dae..bf67661 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -531,6 +531,13 @@ config VIDEO_OV2659
 	  To compile this driver as a module, choose M here: the
 	  module will be called ov2659.
 
+config VIDEO_OV5640
+	tristate "OmniVision OV5640 sensor support"
+	depends on GPIOLIB && VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API
+	---help---
+	  This is a V4L2 sensor-level driver for the Omnivision
+	  OV5640 camera sensor with a MIPI CSI-2 interface.
+
 config VIDEO_OV7640
 	tristate "OmniVision OV7640 sensor support"
 	depends on I2C && VIDEO_V4L2
diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index 5bc7bbe..3a9d73a 100644
--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -57,6 +57,7 @@ obj-$(CONFIG_VIDEO_VP27SMPX) += vp27smpx.o
 obj-$(CONFIG_VIDEO_SONY_BTF_MPX) += sony-btf-mpx.o
 obj-$(CONFIG_VIDEO_UPD64031A) += upd64031a.o
 obj-$(CONFIG_VIDEO_UPD64083) += upd64083.o
+obj-$(CONFIG_VIDEO_OV5640) += ov5640.o
 obj-$(CONFIG_VIDEO_OV7640) += ov7640.o
 obj-$(CONFIG_VIDEO_OV7670) += ov7670.o
 obj-$(CONFIG_VIDEO_OV9650) += ov9650.o
diff --git a/drivers/media/i2c/ov5640.c b/drivers/media/i2c/ov5640.c
new file mode 100644
index 0000000..2d78ec8
--- /dev/null
+++ b/drivers/media/i2c/ov5640.c
@@ -0,0 +1,2231 @@
+/*
+ * Copyright (C) 2011-2013 Freescale Semiconductor, Inc. All Rights Reserved.
+ * Copyright (C) 2014-2017 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/clkdev.h>
+#include <linux/ctype.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/gpio/consumer.h>
+#include <linux/regulator/consumer.h>
+#include <media/v4l2-async.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-of.h>
+#include <media/v4l2-subdev.h>
+
+/* min/typical/max system clock (xclk) frequencies */
+#define OV5640_XCLK_MIN  6000000
+#define OV5640_XCLK_MAX 24000000
+
+/*
+ * FIXME: there is no subdev API to set the MIPI CSI-2
+ * virtual channel yet, so this is hardcoded for now.
+ */
+#define OV5640_MIPI_VC	1
+
+#define OV5640_DEFAULT_SLAVE_ID 0x3c
+
+#define OV5640_REG_CHIP_ID		0x300a
+#define OV5640_REG_PAD_OUTPUT00		0x3019
+#define OV5640_REG_SC_PLL_CTRL0		0x3034
+#define OV5640_REG_SC_PLL_CTRL1		0x3035
+#define OV5640_REG_SC_PLL_CTRL2		0x3036
+#define OV5640_REG_SC_PLL_CTRL3		0x3037
+#define OV5640_REG_SLAVE_ID		0x3100
+#define OV5640_REG_SYS_ROOT_DIVIDER	0x3108
+#define OV5640_REG_AWB_R_GAIN		0x3400
+#define OV5640_REG_AWB_G_GAIN		0x3402
+#define OV5640_REG_AWB_B_GAIN		0x3404
+#define OV5640_REG_AWB_MANUAL_CTRL	0x3406
+#define OV5640_REG_AEC_PK_EXPOSURE_HI	0x3500
+#define OV5640_REG_AEC_PK_EXPOSURE_MED	0x3501
+#define OV5640_REG_AEC_PK_EXPOSURE_LO	0x3502
+#define OV5640_REG_AEC_PK_MANUAL	0x3503
+#define OV5640_REG_AEC_PK_REAL_GAIN	0x350a
+#define OV5640_REG_AEC_PK_VTS		0x350c
+#define OV5640_REG_TIMING_HTS		0x380c
+#define OV5640_REG_TIMING_VTS		0x380e
+#define OV5640_REG_TIMING_TC_REG21	0x3821
+#define OV5640_REG_AEC_CTRL00		0x3a00
+#define OV5640_REG_AEC_B50_STEP		0x3a08
+#define OV5640_REG_AEC_B60_STEP		0x3a0a
+#define OV5640_REG_AEC_CTRL0D		0x3a0d
+#define OV5640_REG_AEC_CTRL0E		0x3a0e
+#define OV5640_REG_AEC_CTRL0F		0x3a0f
+#define OV5640_REG_AEC_CTRL10		0x3a10
+#define OV5640_REG_AEC_CTRL11		0x3a11
+#define OV5640_REG_AEC_CTRL1B		0x3a1b
+#define OV5640_REG_AEC_CTRL1E		0x3a1e
+#define OV5640_REG_AEC_CTRL1F		0x3a1f
+#define OV5640_REG_HZ5060_CTRL00	0x3c00
+#define OV5640_REG_HZ5060_CTRL01	0x3c01
+#define OV5640_REG_SIGMADELTA_CTRL0C	0x3c0c
+#define OV5640_REG_FRAME_CTRL01		0x4202
+#define OV5640_REG_MIPI_CTRL00		0x4800
+#define OV5640_REG_DEBUG_MODE		0x4814
+#define OV5640_REG_PRE_ISP_TEST_SET1	0x503d
+#define OV5640_REG_SDE_CTRL0		0x5580
+#define OV5640_REG_SDE_CTRL1		0x5581
+#define OV5640_REG_SDE_CTRL3		0x5583
+#define OV5640_REG_SDE_CTRL4		0x5584
+#define OV5640_REG_SDE_CTRL5		0x5585
+#define OV5640_REG_AVG_READOUT		0x56a1
+
+enum ov5640_mode_id {
+	OV5640_MODE_QCIF_176_144 = 0,
+	OV5640_MODE_QVGA_320_240,
+	OV5640_MODE_VGA_640_480,
+	OV5640_MODE_NTSC_720_480,
+	OV5640_MODE_PAL_720_576,
+	OV5640_MODE_XGA_1024_768,
+	OV5640_MODE_720P_1280_720,
+	OV5640_MODE_1080P_1920_1080,
+	OV5640_MODE_QSXGA_2592_1944,
+	OV5640_NUM_MODES,
+};
+
+enum ov5640_frame_rate {
+	OV5640_15_FPS = 0,
+	OV5640_30_FPS,
+	OV5640_NUM_FRAMERATES,
+};
+
+static const int ov5640_framerates[] = {
+	[OV5640_15_FPS] = 15,
+	[OV5640_30_FPS] = 30,
+};
+
+/* regulator supplies */
+static const char * const ov5640_supply_name[] = {
+	"DOVDD", /* Digital I/O (1.8V) suppply */
+	"DVDD",  /* Digital Core (1.5V) supply */
+	"AVDD",  /* Analog (2.8V) supply */
+};
+
+#define OV5640_NUM_SUPPLIES ARRAY_SIZE(ov5640_supply_name)
+
+/*
+ * image size under 1280 * 960 are SUBSAMPLING
+ * image size upper 1280 * 960 are SCALING
+ */
+enum ov5640_downsize_mode {
+	SUBSAMPLING,
+	SCALING,
+};
+
+struct reg_value {
+	u16 reg_addr;
+	u8 val;
+	u8 mask;
+	u32 delay_ms;
+};
+
+struct ov5640_mode_info {
+	enum ov5640_mode_id id;
+	enum ov5640_downsize_mode dn_mode;
+	u32 width;
+	u32 height;
+	const struct reg_value *reg_data;
+	u32 reg_data_size;
+};
+
+struct ov5640_ctrls {
+	struct v4l2_ctrl_handler handler;
+	struct {
+		struct v4l2_ctrl *auto_exp;
+		struct v4l2_ctrl *exposure;
+	};
+	struct {
+		struct v4l2_ctrl *auto_wb;
+		struct v4l2_ctrl *blue_balance;
+		struct v4l2_ctrl *red_balance;
+	};
+	struct {
+		struct v4l2_ctrl *auto_gain;
+		struct v4l2_ctrl *gain;
+	};
+	struct v4l2_ctrl *brightness;
+	struct v4l2_ctrl *saturation;
+	struct v4l2_ctrl *contrast;
+	struct v4l2_ctrl *hue;
+	struct v4l2_ctrl *test_pattern;
+};
+
+struct ov5640_dev {
+	struct i2c_client *i2c_client;
+	struct v4l2_subdev sd;
+	struct media_pad pad;
+	struct v4l2_of_endpoint ep; /* the parsed DT endpoint info */
+	struct clk *xclk; /* system clock to OV5640 */
+	u32 xclk_freq;
+
+	struct regulator_bulk_data supplies[OV5640_NUM_SUPPLIES];
+	struct gpio_desc *reset_gpio;
+	struct gpio_desc *pwdn_gpio;
+
+	/* lock to protect all members below */
+	struct mutex lock;
+
+	int power_count;
+
+	struct v4l2_mbus_framefmt fmt;
+	struct v4l2_captureparm streamcap;
+
+	const struct ov5640_mode_info *current_mode;
+	enum ov5640_frame_rate current_fr;
+
+	struct ov5640_ctrls ctrls;
+
+	u32 prev_sysclk, prev_hts;
+	u32 ae_low, ae_high, ae_target;
+
+	bool pending_mode_change;
+	bool streaming;
+};
+
+static inline struct ov5640_dev *to_ov5640_dev(struct v4l2_subdev *sd)
+{
+	return container_of(sd, struct ov5640_dev, sd);
+}
+
+static inline struct v4l2_subdev *ctrl_to_sd(struct v4l2_ctrl *ctrl)
+{
+	return &container_of(ctrl->handler, struct ov5640_dev,
+			     ctrls.handler)->sd;
+}
+
+/*
+ * FIXME: all of these register tables are likely filled with
+ * entries that set the register to their power-on default values,
+ * and which are otherwise not touched by this driver. Those entries
+ * should be identified and removed to speed register load time
+ * over i2c.
+ */
+
+static const struct reg_value ov5640_init_setting_30fps_VGA[] = {
+
+	{0x3103, 0x11, 0, 0}, {0x3008, 0x82, 0, 5}, {0x3008, 0x42, 0, 0},
+	{0x3103, 0x03, 0, 0}, {0x3017, 0x00, 0, 0}, {0x3018, 0x00, 0, 0},
+	{0x3034, 0x18, 0, 0}, {0x3035, 0x14, 0, 0}, {0x3036, 0x38, 0, 0},
+	{0x3037, 0x13, 0, 0}, {0x3108, 0x01, 0, 0}, {0x3630, 0x36, 0, 0},
+	{0x3631, 0x0e, 0, 0}, {0x3632, 0xe2, 0, 0}, {0x3633, 0x12, 0, 0},
+	{0x3621, 0xe0, 0, 0}, {0x3704, 0xa0, 0, 0}, {0x3703, 0x5a, 0, 0},
+	{0x3715, 0x78, 0, 0}, {0x3717, 0x01, 0, 0}, {0x370b, 0x60, 0, 0},
+	{0x3705, 0x1a, 0, 0}, {0x3905, 0x02, 0, 0}, {0x3906, 0x10, 0, 0},
+	{0x3901, 0x0a, 0, 0}, {0x3731, 0x12, 0, 0}, {0x3600, 0x08, 0, 0},
+	{0x3601, 0x33, 0, 0}, {0x302d, 0x60, 0, 0}, {0x3620, 0x52, 0, 0},
+	{0x371b, 0x20, 0, 0}, {0x471c, 0x50, 0, 0}, {0x3a13, 0x43, 0, 0},
+	{0x3a18, 0x00, 0, 0}, {0x3a19, 0xf8, 0, 0}, {0x3635, 0x13, 0, 0},
+	{0x3636, 0x03, 0, 0}, {0x3634, 0x40, 0, 0}, {0x3622, 0x01, 0, 0},
+	{0x3c01, 0xa4, 0, 0}, {0x3c04, 0x28, 0, 0}, {0x3c05, 0x98, 0, 0},
+	{0x3c06, 0x00, 0, 0}, {0x3c07, 0x08, 0, 0}, {0x3c08, 0x00, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0x80, 0, 0}, {0x380a, 0x01, 0, 0},
+	{0x380b, 0xe0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x3000, 0x00, 0, 0},
+	{0x3002, 0x1c, 0, 0}, {0x3004, 0xff, 0, 0}, {0x3006, 0xc3, 0, 0},
+	{0x300e, 0x45, 0, 0}, {0x302e, 0x08, 0, 0}, {0x4300, 0x3f, 0, 0},
+	{0x501f, 0x00, 0, 0}, {0x4713, 0x03, 0, 0}, {0x4407, 0x04, 0, 0},
+	{0x440e, 0x00, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x4837, 0x0a, 0, 0}, {0x4800, 0x04, 0, 0}, {0x3824, 0x02, 0, 0},
+	{0x5000, 0xa7, 0, 0}, {0x5001, 0xa3, 0, 0}, {0x5180, 0xff, 0, 0},
+	{0x5181, 0xf2, 0, 0}, {0x5182, 0x00, 0, 0}, {0x5183, 0x14, 0, 0},
+	{0x5184, 0x25, 0, 0}, {0x5185, 0x24, 0, 0}, {0x5186, 0x09, 0, 0},
+	{0x5187, 0x09, 0, 0}, {0x5188, 0x09, 0, 0}, {0x5189, 0x88, 0, 0},
+	{0x518a, 0x54, 0, 0}, {0x518b, 0xee, 0, 0}, {0x518c, 0xb2, 0, 0},
+	{0x518d, 0x50, 0, 0}, {0x518e, 0x34, 0, 0}, {0x518f, 0x6b, 0, 0},
+	{0x5190, 0x46, 0, 0}, {0x5191, 0xf8, 0, 0}, {0x5192, 0x04, 0, 0},
+	{0x5193, 0x70, 0, 0}, {0x5194, 0xf0, 0, 0}, {0x5195, 0xf0, 0, 0},
+	{0x5196, 0x03, 0, 0}, {0x5197, 0x01, 0, 0}, {0x5198, 0x04, 0, 0},
+	{0x5199, 0x6c, 0, 0}, {0x519a, 0x04, 0, 0}, {0x519b, 0x00, 0, 0},
+	{0x519c, 0x09, 0, 0}, {0x519d, 0x2b, 0, 0}, {0x519e, 0x38, 0, 0},
+	{0x5381, 0x1e, 0, 0}, {0x5382, 0x5b, 0, 0}, {0x5383, 0x08, 0, 0},
+	{0x5384, 0x0a, 0, 0}, {0x5385, 0x7e, 0, 0}, {0x5386, 0x88, 0, 0},
+	{0x5387, 0x7c, 0, 0}, {0x5388, 0x6c, 0, 0}, {0x5389, 0x10, 0, 0},
+	{0x538a, 0x01, 0, 0}, {0x538b, 0x98, 0, 0}, {0x5300, 0x08, 0, 0},
+	{0x5301, 0x30, 0, 0}, {0x5302, 0x10, 0, 0}, {0x5303, 0x00, 0, 0},
+	{0x5304, 0x08, 0, 0}, {0x5305, 0x30, 0, 0}, {0x5306, 0x08, 0, 0},
+	{0x5307, 0x16, 0, 0}, {0x5309, 0x08, 0, 0}, {0x530a, 0x30, 0, 0},
+	{0x530b, 0x04, 0, 0}, {0x530c, 0x06, 0, 0}, {0x5480, 0x01, 0, 0},
+	{0x5481, 0x08, 0, 0}, {0x5482, 0x14, 0, 0}, {0x5483, 0x28, 0, 0},
+	{0x5484, 0x51, 0, 0}, {0x5485, 0x65, 0, 0}, {0x5486, 0x71, 0, 0},
+	{0x5487, 0x7d, 0, 0}, {0x5488, 0x87, 0, 0}, {0x5489, 0x91, 0, 0},
+	{0x548a, 0x9a, 0, 0}, {0x548b, 0xaa, 0, 0}, {0x548c, 0xb8, 0, 0},
+	{0x548d, 0xcd, 0, 0}, {0x548e, 0xdd, 0, 0}, {0x548f, 0xea, 0, 0},
+	{0x5490, 0x1d, 0, 0}, {0x5580, 0x02, 0, 0}, {0x5583, 0x40, 0, 0},
+	{0x5584, 0x10, 0, 0}, {0x5589, 0x10, 0, 0}, {0x558a, 0x00, 0, 0},
+	{0x558b, 0xf8, 0, 0}, {0x5800, 0x23, 0, 0}, {0x5801, 0x14, 0, 0},
+	{0x5802, 0x0f, 0, 0}, {0x5803, 0x0f, 0, 0}, {0x5804, 0x12, 0, 0},
+	{0x5805, 0x26, 0, 0}, {0x5806, 0x0c, 0, 0}, {0x5807, 0x08, 0, 0},
+	{0x5808, 0x05, 0, 0}, {0x5809, 0x05, 0, 0}, {0x580a, 0x08, 0, 0},
+	{0x580b, 0x0d, 0, 0}, {0x580c, 0x08, 0, 0}, {0x580d, 0x03, 0, 0},
+	{0x580e, 0x00, 0, 0}, {0x580f, 0x00, 0, 0}, {0x5810, 0x03, 0, 0},
+	{0x5811, 0x09, 0, 0}, {0x5812, 0x07, 0, 0}, {0x5813, 0x03, 0, 0},
+	{0x5814, 0x00, 0, 0}, {0x5815, 0x01, 0, 0}, {0x5816, 0x03, 0, 0},
+	{0x5817, 0x08, 0, 0}, {0x5818, 0x0d, 0, 0}, {0x5819, 0x08, 0, 0},
+	{0x581a, 0x05, 0, 0}, {0x581b, 0x06, 0, 0}, {0x581c, 0x08, 0, 0},
+	{0x581d, 0x0e, 0, 0}, {0x581e, 0x29, 0, 0}, {0x581f, 0x17, 0, 0},
+	{0x5820, 0x11, 0, 0}, {0x5821, 0x11, 0, 0}, {0x5822, 0x15, 0, 0},
+	{0x5823, 0x28, 0, 0}, {0x5824, 0x46, 0, 0}, {0x5825, 0x26, 0, 0},
+	{0x5826, 0x08, 0, 0}, {0x5827, 0x26, 0, 0}, {0x5828, 0x64, 0, 0},
+	{0x5829, 0x26, 0, 0}, {0x582a, 0x24, 0, 0}, {0x582b, 0x22, 0, 0},
+	{0x582c, 0x24, 0, 0}, {0x582d, 0x24, 0, 0}, {0x582e, 0x06, 0, 0},
+	{0x582f, 0x22, 0, 0}, {0x5830, 0x40, 0, 0}, {0x5831, 0x42, 0, 0},
+	{0x5832, 0x24, 0, 0}, {0x5833, 0x26, 0, 0}, {0x5834, 0x24, 0, 0},
+	{0x5835, 0x22, 0, 0}, {0x5836, 0x22, 0, 0}, {0x5837, 0x26, 0, 0},
+	{0x5838, 0x44, 0, 0}, {0x5839, 0x24, 0, 0}, {0x583a, 0x26, 0, 0},
+	{0x583b, 0x28, 0, 0}, {0x583c, 0x42, 0, 0}, {0x583d, 0xce, 0, 0},
+	{0x5025, 0x00, 0, 0}, {0x3a0f, 0x30, 0, 0}, {0x3a10, 0x28, 0, 0},
+	{0x3a1b, 0x30, 0, 0}, {0x3a1e, 0x26, 0, 0}, {0x3a11, 0x60, 0, 0},
+	{0x3a1f, 0x14, 0, 0}, {0x3008, 0x02, 0, 0}, {0x3c00, 0x04, 0, 300},
+};
+
+static const struct reg_value ov5640_setting_30fps_VGA_640_480[] = {
+
+	{0x3035, 0x14, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0x80, 0, 0}, {0x380a, 0x01, 0, 0},
+	{0x380b, 0xe0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x04, 0, 0}, {0x380f, 0x38, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x0e, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0}, {0x3503, 0x00, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_VGA_640_480[] = {
+	{0x3035, 0x22, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0x80, 0, 0}, {0x380a, 0x01, 0, 0},
+	{0x380b, 0xe0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_30fps_XGA_1024_768[] = {
+
+	{0x3035, 0x14, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0x80, 0, 0}, {0x380a, 0x01, 0, 0},
+	{0x380b, 0xe0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x04, 0, 0}, {0x380f, 0x38, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x0e, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0}, {0x3503, 0x00, 0, 0},
+	{0x3808, 0x04, 0, 0}, {0x3809, 0x00, 0, 0}, {0x380a, 0x03, 0, 0},
+	{0x380b, 0x00, 0, 0}, {0x3035, 0x12, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_XGA_1024_768[] = {
+	{0x3035, 0x22, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0x80, 0, 0}, {0x380a, 0x01, 0, 0},
+	{0x380b, 0xe0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0}, {0x3808, 0x04, 0, 0},
+	{0x3809, 0x00, 0, 0}, {0x380a, 0x03, 0, 0}, {0x380b, 0x00, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_30fps_QVGA_320_240[] = {
+	{0x3035, 0x14, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x01, 0, 0}, {0x3809, 0x40, 0, 0}, {0x380a, 0x00, 0, 0},
+	{0x380b, 0xf0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_QVGA_320_240[] = {
+	{0x3035, 0x22, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x01, 0, 0}, {0x3809, 0x40, 0, 0}, {0x380a, 0x00, 0, 0},
+	{0x380b, 0xf0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_30fps_QCIF_176_144[] = {
+	{0x3035, 0x14, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x00, 0, 0}, {0x3809, 0xb0, 0, 0}, {0x380a, 0x00, 0, 0},
+	{0x380b, 0x90, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+static const struct reg_value ov5640_setting_15fps_QCIF_176_144[] = {
+	{0x3035, 0x22, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x00, 0, 0}, {0x3809, 0xb0, 0, 0}, {0x380a, 0x00, 0, 0},
+	{0x380b, 0x90, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_30fps_NTSC_720_480[] = {
+	{0x3035, 0x12, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0xd0, 0, 0}, {0x380a, 0x01, 0, 0},
+	{0x380b, 0xe0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x3c, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_NTSC_720_480[] = {
+	{0x3035, 0x22, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0xd0, 0, 0}, {0x380a, 0x01, 0, 0},
+	{0x380b, 0xe0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x3c, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_30fps_PAL_720_576[] = {
+	{0x3035, 0x12, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0xd0, 0, 0}, {0x380a, 0x02, 0, 0},
+	{0x380b, 0x40, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x38, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_PAL_720_576[] = {
+	{0x3035, 0x22, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0xd0, 0, 0}, {0x380a, 0x02, 0, 0},
+	{0x380b, 0x40, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x38, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_30fps_720P_1280_720[] = {
+	{0x3008, 0x42, 0, 0},
+	{0x3035, 0x21, 0, 0}, {0x3036, 0x54, 0, 0}, {0x3c07, 0x07, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0xfa, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x06, 0, 0}, {0x3807, 0xa9, 0, 0},
+	{0x3808, 0x05, 0, 0}, {0x3809, 0x00, 0, 0}, {0x380a, 0x02, 0, 0},
+	{0x380b, 0xd0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x64, 0, 0},
+	{0x380e, 0x02, 0, 0}, {0x380f, 0xe4, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x04, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x02, 0, 0},
+	{0x3a03, 0xe4, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0xbc, 0, 0},
+	{0x3a0a, 0x01, 0, 0}, {0x3a0b, 0x72, 0, 0}, {0x3a0e, 0x01, 0, 0},
+	{0x3a0d, 0x02, 0, 0}, {0x3a14, 0x02, 0, 0}, {0x3a15, 0xe4, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x02, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x37, 0, 0}, {0x460c, 0x20, 0, 0},
+	{0x3824, 0x04, 0, 0}, {0x5001, 0x83, 0, 0}, {0x4005, 0x1a, 0, 0},
+	{0x3008, 0x02, 0, 0}, {0x3503, 0,    0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_720P_1280_720[] = {
+	{0x3035, 0x41, 0, 0}, {0x3036, 0x54, 0, 0}, {0x3c07, 0x07, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0xfa, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x06, 0, 0}, {0x3807, 0xa9, 0, 0},
+	{0x3808, 0x05, 0, 0}, {0x3809, 0x00, 0, 0}, {0x380a, 0x02, 0, 0},
+	{0x380b, 0xd0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x64, 0, 0},
+	{0x380e, 0x02, 0, 0}, {0x380f, 0xe4, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x04, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x02, 0, 0},
+	{0x3a03, 0xe4, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0xbc, 0, 0},
+	{0x3a0a, 0x01, 0, 0}, {0x3a0b, 0x72, 0, 0}, {0x3a0e, 0x01, 0, 0},
+	{0x3a0d, 0x02, 0, 0}, {0x3a14, 0x02, 0, 0}, {0x3a15, 0xe4, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x02, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x37, 0, 0}, {0x460c, 0x20, 0, 0},
+	{0x3824, 0x04, 0, 0}, {0x5001, 0x83, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_30fps_1080P_1920_1080[] = {
+	{0x3008, 0x42, 0, 0},
+	{0x3035, 0x21, 0, 0}, {0x3036, 0x54, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x40, 0, 0}, {0x3821, 0x06, 0, 0}, {0x3814, 0x11, 0, 0},
+	{0x3815, 0x11, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x00, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9f, 0, 0},
+	{0x3808, 0x0a, 0, 0}, {0x3809, 0x20, 0, 0}, {0x380a, 0x07, 0, 0},
+	{0x380b, 0x98, 0, 0}, {0x380c, 0x0b, 0, 0}, {0x380d, 0x1c, 0, 0},
+	{0x380e, 0x07, 0, 0}, {0x380f, 0xb0, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x04, 0, 0},
+	{0x3618, 0x04, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x21, 0, 0},
+	{0x3709, 0x12, 0, 0}, {0x370c, 0x00, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x06, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0x83, 0, 0}, {0x3035, 0x11, 0, 0},
+	{0x3036, 0x54, 0, 0}, {0x3c07, 0x07, 0, 0}, {0x3c08, 0x00, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3800, 0x01, 0, 0}, {0x3801, 0x50, 0, 0}, {0x3802, 0x01, 0, 0},
+	{0x3803, 0xb2, 0, 0}, {0x3804, 0x08, 0, 0}, {0x3805, 0xef, 0, 0},
+	{0x3806, 0x05, 0, 0}, {0x3807, 0xf1, 0, 0}, {0x3808, 0x07, 0, 0},
+	{0x3809, 0x80, 0, 0}, {0x380a, 0x04, 0, 0}, {0x380b, 0x38, 0, 0},
+	{0x380c, 0x09, 0, 0}, {0x380d, 0xc4, 0, 0}, {0x380e, 0x04, 0, 0},
+	{0x380f, 0x60, 0, 0}, {0x3612, 0x2b, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3a02, 0x04, 0, 0}, {0x3a03, 0x60, 0, 0}, {0x3a08, 0x01, 0, 0},
+	{0x3a09, 0x50, 0, 0}, {0x3a0a, 0x01, 0, 0}, {0x3a0b, 0x18, 0, 0},
+	{0x3a0e, 0x03, 0, 0}, {0x3a0d, 0x04, 0, 0}, {0x3a14, 0x04, 0, 0},
+	{0x3a15, 0x60, 0, 0}, {0x4713, 0x02, 0, 0}, {0x4407, 0x04, 0, 0},
+	{0x460b, 0x37, 0, 0}, {0x460c, 0x20, 0, 0}, {0x3824, 0x04, 0, 0},
+	{0x4005, 0x1a, 0, 0}, {0x3008, 0x02, 0, 0},
+	{0x3503, 0, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_1080P_1920_1080[] = {
+	{0x3008, 0x42, 0, 0},
+	{0x3035, 0x21, 0, 0}, {0x3036, 0x54, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x40, 0, 0}, {0x3821, 0x06, 0, 0}, {0x3814, 0x11, 0, 0},
+	{0x3815, 0x11, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x00, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9f, 0, 0},
+	{0x3808, 0x0a, 0, 0}, {0x3809, 0x20, 0, 0}, {0x380a, 0x07, 0, 0},
+	{0x380b, 0x98, 0, 0}, {0x380c, 0x0b, 0, 0}, {0x380d, 0x1c, 0, 0},
+	{0x380e, 0x07, 0, 0}, {0x380f, 0xb0, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x04, 0, 0},
+	{0x3618, 0x04, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x21, 0, 0},
+	{0x3709, 0x12, 0, 0}, {0x370c, 0x00, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x06, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0x83, 0, 0}, {0x3035, 0x21, 0, 0},
+	{0x3036, 0x54, 0, 1}, {0x3c07, 0x07, 0, 0}, {0x3c08, 0x00, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3800, 0x01, 0, 0}, {0x3801, 0x50, 0, 0}, {0x3802, 0x01, 0, 0},
+	{0x3803, 0xb2, 0, 0}, {0x3804, 0x08, 0, 0}, {0x3805, 0xef, 0, 0},
+	{0x3806, 0x05, 0, 0}, {0x3807, 0xf1, 0, 0}, {0x3808, 0x07, 0, 0},
+	{0x3809, 0x80, 0, 0}, {0x380a, 0x04, 0, 0}, {0x380b, 0x38, 0, 0},
+	{0x380c, 0x09, 0, 0}, {0x380d, 0xc4, 0, 0}, {0x380e, 0x04, 0, 0},
+	{0x380f, 0x60, 0, 0}, {0x3612, 0x2b, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3a02, 0x04, 0, 0}, {0x3a03, 0x60, 0, 0}, {0x3a08, 0x01, 0, 0},
+	{0x3a09, 0x50, 0, 0}, {0x3a0a, 0x01, 0, 0}, {0x3a0b, 0x18, 0, 0},
+	{0x3a0e, 0x03, 0, 0}, {0x3a0d, 0x04, 0, 0}, {0x3a14, 0x04, 0, 0},
+	{0x3a15, 0x60, 0, 0}, {0x4713, 0x02, 0, 0}, {0x4407, 0x04, 0, 0},
+	{0x460b, 0x37, 0, 0}, {0x460c, 0x20, 0, 0}, {0x3824, 0x04, 0, 0},
+	{0x4005, 0x1a, 0, 0}, {0x3008, 0x02, 0, 0}, {0x3503, 0, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_QSXGA_2592_1944[] = {
+	{0x3820, 0x40, 0, 0}, {0x3821, 0x06, 0, 0},
+	{0x3035, 0x21, 0, 0}, {0x3036, 0x54, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x40, 0, 0}, {0x3821, 0x06, 0, 0}, {0x3814, 0x11, 0, 0},
+	{0x3815, 0x11, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x00, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9f, 0, 0},
+	{0x3808, 0x0a, 0, 0}, {0x3809, 0x20, 0, 0}, {0x380a, 0x07, 0, 0},
+	{0x380b, 0x98, 0, 0}, {0x380c, 0x0b, 0, 0}, {0x380d, 0x1c, 0, 0},
+	{0x380e, 0x07, 0, 0}, {0x380f, 0xb0, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x04, 0, 0},
+	{0x3618, 0x04, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x21, 0, 0},
+	{0x3709, 0x12, 0, 0}, {0x370c, 0x00, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x06, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0x83, 0, 70},
+};
+
+/* power-on sensor init reg table */
+static const struct ov5640_mode_info ov5640_mode_init_data = {
+	0, SUBSAMPLING, 640, 480, ov5640_init_setting_30fps_VGA,
+	ARRAY_SIZE(ov5640_init_setting_30fps_VGA),
+};
+
+static const struct ov5640_mode_info
+ov5640_mode_data[OV5640_NUM_FRAMERATES][OV5640_NUM_MODES] = {
+	{
+		{OV5640_MODE_QCIF_176_144, SUBSAMPLING, 176, 144,
+		 ov5640_setting_15fps_QCIF_176_144,
+		 ARRAY_SIZE(ov5640_setting_15fps_QCIF_176_144)},
+		{OV5640_MODE_QVGA_320_240, SUBSAMPLING, 320,  240,
+		 ov5640_setting_15fps_QVGA_320_240,
+		 ARRAY_SIZE(ov5640_setting_15fps_QVGA_320_240)},
+		{OV5640_MODE_VGA_640_480, SUBSAMPLING, 640,  480,
+		 ov5640_setting_15fps_VGA_640_480,
+		 ARRAY_SIZE(ov5640_setting_15fps_VGA_640_480)},
+		{OV5640_MODE_NTSC_720_480, SUBSAMPLING, 720, 480,
+		 ov5640_setting_15fps_NTSC_720_480,
+		 ARRAY_SIZE(ov5640_setting_15fps_NTSC_720_480)},
+		{OV5640_MODE_PAL_720_576, SUBSAMPLING, 720, 576,
+		 ov5640_setting_15fps_PAL_720_576,
+		 ARRAY_SIZE(ov5640_setting_15fps_PAL_720_576)},
+		{OV5640_MODE_XGA_1024_768, SUBSAMPLING, 1024, 768,
+		 ov5640_setting_15fps_XGA_1024_768,
+		 ARRAY_SIZE(ov5640_setting_15fps_XGA_1024_768)},
+		{OV5640_MODE_720P_1280_720, SUBSAMPLING, 1280, 720,
+		 ov5640_setting_15fps_720P_1280_720,
+		 ARRAY_SIZE(ov5640_setting_15fps_720P_1280_720)},
+		{OV5640_MODE_1080P_1920_1080, SCALING, 1920, 1080,
+		 ov5640_setting_15fps_1080P_1920_1080,
+		 ARRAY_SIZE(ov5640_setting_15fps_1080P_1920_1080)},
+		{OV5640_MODE_QSXGA_2592_1944, SCALING, 2592, 1944,
+		 ov5640_setting_15fps_QSXGA_2592_1944,
+		 ARRAY_SIZE(ov5640_setting_15fps_QSXGA_2592_1944)},
+	}, {
+		{OV5640_MODE_QCIF_176_144, SUBSAMPLING, 176, 144,
+		 ov5640_setting_30fps_QCIF_176_144,
+		 ARRAY_SIZE(ov5640_setting_30fps_QCIF_176_144)},
+		{OV5640_MODE_QVGA_320_240, SUBSAMPLING, 320,  240,
+		 ov5640_setting_30fps_QVGA_320_240,
+		 ARRAY_SIZE(ov5640_setting_30fps_QVGA_320_240)},
+		{OV5640_MODE_VGA_640_480, SUBSAMPLING, 640,  480,
+		 ov5640_setting_30fps_VGA_640_480,
+		 ARRAY_SIZE(ov5640_setting_30fps_VGA_640_480)},
+		{OV5640_MODE_NTSC_720_480, SUBSAMPLING, 720, 480,
+		 ov5640_setting_30fps_NTSC_720_480,
+		 ARRAY_SIZE(ov5640_setting_30fps_NTSC_720_480)},
+		{OV5640_MODE_PAL_720_576, SUBSAMPLING, 720, 576,
+		 ov5640_setting_30fps_PAL_720_576,
+		 ARRAY_SIZE(ov5640_setting_30fps_PAL_720_576)},
+		{OV5640_MODE_XGA_1024_768, SUBSAMPLING, 1024, 768,
+		 ov5640_setting_30fps_XGA_1024_768,
+		 ARRAY_SIZE(ov5640_setting_30fps_XGA_1024_768)},
+		{OV5640_MODE_720P_1280_720, SUBSAMPLING, 1280, 720,
+		 ov5640_setting_30fps_720P_1280_720,
+		 ARRAY_SIZE(ov5640_setting_30fps_720P_1280_720)},
+		{OV5640_MODE_1080P_1920_1080, SCALING, 1920, 1080,
+		 ov5640_setting_30fps_1080P_1920_1080,
+		 ARRAY_SIZE(ov5640_setting_30fps_1080P_1920_1080)},
+		{OV5640_MODE_QSXGA_2592_1944, -1, 0, 0, NULL, 0},
+	},
+};
+
+static int ov5640_init_slave_id(struct ov5640_dev *sensor)
+{
+	struct i2c_client *client = sensor->i2c_client;
+	struct i2c_msg msg;
+	u8 buf[3];
+	int ret;
+
+	if (client->addr == OV5640_DEFAULT_SLAVE_ID)
+		return 0;
+
+	buf[0] = OV5640_REG_SLAVE_ID >> 8;
+	buf[1] = OV5640_REG_SLAVE_ID & 0xff;
+	buf[2] = client->addr << 1;
+
+	msg.addr = OV5640_DEFAULT_SLAVE_ID;
+	msg.flags = 0;
+	msg.buf = buf;
+	msg.len = sizeof(buf);
+
+	ret = i2c_transfer(client->adapter, &msg, 1);
+	if (ret < 0) {
+		dev_err(&client->dev, "%s: failed with %d\n", __func__, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int ov5640_write_reg(struct ov5640_dev *sensor, u16 reg, u8 val)
+{
+	struct i2c_client *client = sensor->i2c_client;
+	struct i2c_msg msg;
+	u8 buf[3];
+	int ret;
+
+	buf[0] = reg >> 8;
+	buf[1] = reg & 0xff;
+	buf[2] = val;
+
+	msg.addr = client->addr;
+	msg.flags = client->flags;
+	msg.buf = buf;
+	msg.len = sizeof(buf);
+
+	ret = i2c_transfer(client->adapter, &msg, 1);
+	if (ret < 0) {
+		v4l2_err(&sensor->sd, "%s: error: reg=%x, val=%x\n",
+			__func__, reg, val);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int ov5640_read_reg(struct ov5640_dev *sensor, u16 reg, u8 *val)
+{
+	struct i2c_client *client = sensor->i2c_client;
+	struct i2c_msg msg[2];
+	u8 buf[2];
+	int ret;
+
+	buf[0] = reg >> 8;
+	buf[1] = reg & 0xff;
+
+	msg[0].addr = client->addr;
+	msg[0].flags = client->flags;
+	msg[0].buf = buf;
+	msg[0].len = sizeof(buf);
+
+	msg[1].addr = client->addr;
+	msg[1].flags = client->flags | I2C_M_RD;
+	msg[1].buf = buf;
+	msg[1].len = 1;
+
+	ret = i2c_transfer(client->adapter, msg, 2);
+	if (ret < 0)
+		return ret;
+
+	*val = buf[0];
+	return 0;
+}
+
+static int ov5640_read_reg16(struct ov5640_dev *sensor, u16 reg, u16 *val)
+{
+	u8 hi, lo;
+
+	ov5640_read_reg(sensor, reg, &hi);
+	ov5640_read_reg(sensor, reg+1, &lo);
+
+	*val = ((u16)hi << 8) | (u16)lo;
+	return 0;
+}
+
+static int ov5640_write_reg16(struct ov5640_dev *sensor, u16 reg, u16 val)
+{
+	ov5640_write_reg(sensor, reg, val >> 8);
+	ov5640_write_reg(sensor, reg + 1, val & 0xff);
+	return 0;
+}
+
+static int ov5640_mod_reg(struct ov5640_dev *sensor, u16 reg,
+			  u8 mask, u8 val)
+{
+	u8 readval;
+
+	ov5640_read_reg(sensor, reg, &readval);
+
+	readval &= ~mask;
+	val &= mask;
+	val |= readval;
+
+	ov5640_write_reg(sensor, reg, val);
+	return 0;
+}
+
+/* download ov5640 settings to sensor through i2c */
+static int ov5640_load_regs(struct ov5640_dev *sensor,
+			    const struct ov5640_mode_info *mode)
+{
+	const struct reg_value *regs = mode->reg_data;
+	unsigned int i;
+	u32 delay_ms;
+	u16 reg_addr;
+	u8 mask, val;
+
+	for (i = 0; i < mode->reg_data_size; ++i, ++regs) {
+		delay_ms = regs->delay_ms;
+		reg_addr = regs->reg_addr;
+		val = regs->val;
+		mask = regs->mask;
+
+		if (mask)
+			ov5640_mod_reg(sensor, reg_addr, mask, val);
+		else
+			ov5640_write_reg(sensor, reg_addr, val);
+		if (delay_ms)
+			usleep_range(1000*delay_ms, 1000*delay_ms+100);
+	}
+
+	return 0;
+}
+
+static int ov5640_set_hue(struct ov5640_dev *sensor, int value)
+{
+	if (value) {
+		ov5640_mod_reg(sensor, OV5640_REG_SDE_CTRL0, BIT(0), BIT(0));
+		ov5640_write_reg16(sensor, OV5640_REG_SDE_CTRL1, value);
+	} else {
+		ov5640_mod_reg(sensor, OV5640_REG_SDE_CTRL0, BIT(0), 0);
+	}
+
+	return 0;
+}
+
+static int ov5640_set_contrast(struct ov5640_dev *sensor, int value)
+{
+	if (value) {
+		ov5640_mod_reg(sensor, OV5640_REG_SDE_CTRL0, BIT(2), BIT(2));
+		ov5640_write_reg(sensor, OV5640_REG_SDE_CTRL5, value & 0xff);
+	} else {
+		ov5640_mod_reg(sensor, OV5640_REG_SDE_CTRL0, BIT(2), 0);
+	}
+
+	return 0;
+}
+
+static int ov5640_set_saturation(struct ov5640_dev *sensor, int value)
+{
+	if (value) {
+		ov5640_mod_reg(sensor, OV5640_REG_SDE_CTRL0, BIT(1), BIT(1));
+		ov5640_write_reg(sensor, OV5640_REG_SDE_CTRL3, value & 0xff);
+		ov5640_write_reg(sensor, OV5640_REG_SDE_CTRL4, value & 0xff);
+	} else {
+		ov5640_mod_reg(sensor, OV5640_REG_SDE_CTRL0, BIT(1), 0);
+	}
+
+	return 0;
+}
+
+static int ov5640_set_white_balance(struct ov5640_dev *sensor, int awb)
+{
+	ov5640_mod_reg(sensor, OV5640_REG_AWB_MANUAL_CTRL,
+		       BIT(0), awb ? 0 : 1);
+
+	if (!awb) {
+		u16 red = (u16)sensor->ctrls.red_balance->val;
+		u16 blue = (u16)sensor->ctrls.blue_balance->val;
+
+		ov5640_write_reg16(sensor, OV5640_REG_AWB_R_GAIN, red);
+		ov5640_write_reg16(sensor, OV5640_REG_AWB_B_GAIN, blue);
+	}
+
+	return 0;
+}
+
+static int ov5640_set_exposure(struct ov5640_dev *sensor, int exp)
+{
+	struct ov5640_ctrls *ctrls = &sensor->ctrls;
+	bool auto_exposure = (exp == V4L2_EXPOSURE_AUTO);
+
+	if (ctrls->auto_exp->is_new) {
+		ov5640_mod_reg(sensor, OV5640_REG_AEC_PK_MANUAL,
+			       BIT(0), auto_exposure ? 0 : BIT(0));
+	}
+
+	if (!auto_exposure && ctrls->exposure->is_new) {
+		u16 max_exp;
+
+		ov5640_read_reg16(sensor, OV5640_REG_AEC_PK_VTS, &max_exp);
+		if (ctrls->exposure->val < max_exp) {
+			u32 exposure = ctrls->exposure->val << 4;
+
+			ov5640_write_reg(sensor, OV5640_REG_AEC_PK_EXPOSURE_LO,
+					 exposure & 0xff);
+			ov5640_write_reg(sensor, OV5640_REG_AEC_PK_EXPOSURE_MED,
+					 (exposure >> 8) & 0xff);
+			ov5640_write_reg(sensor, OV5640_REG_AEC_PK_EXPOSURE_HI,
+					 (exposure >> 16) & 0x0f);
+		}
+	}
+
+	return 0;
+}
+
+/* read exposure, in number of line periods */
+static int ov5640_get_exposure(struct ov5640_dev *sensor)
+{
+	u8 temp;
+	int exp;
+
+	ov5640_read_reg(sensor, OV5640_REG_AEC_PK_EXPOSURE_HI, &temp);
+	exp = ((int)temp & 0x0f) << 16;
+	ov5640_read_reg(sensor, OV5640_REG_AEC_PK_EXPOSURE_MED, &temp);
+	exp |= ((int)temp << 8);
+	ov5640_read_reg(sensor, OV5640_REG_AEC_PK_EXPOSURE_LO, &temp);
+	exp |= (int)temp;
+
+	return exp >> 4;
+}
+
+static int ov5640_set_gain(struct ov5640_dev *sensor, int auto_gain)
+{
+	struct ov5640_ctrls *ctrls = &sensor->ctrls;
+
+	if (ctrls->auto_gain->is_new) {
+		ov5640_mod_reg(sensor, OV5640_REG_AEC_PK_MANUAL,
+			       BIT(1), ctrls->auto_gain->val ? 0 : BIT(1));
+	}
+
+	if (!auto_gain && ctrls->gain->is_new) {
+		u16 gain = (u16)ctrls->gain->val;
+
+		ov5640_write_reg16(sensor, OV5640_REG_AEC_PK_REAL_GAIN,
+				   gain & 0x3ff);
+	}
+
+	return 0;
+}
+
+static int ov5640_get_gain(struct ov5640_dev *sensor)
+{
+	u16 gain;
+
+	ov5640_read_reg16(sensor, OV5640_REG_AEC_PK_REAL_GAIN, &gain);
+
+	return gain & 0x3ff;
+}
+
+static int ov5640_set_agc_aec(struct ov5640_dev *sensor, bool on)
+{
+	ov5640_mod_reg(sensor, OV5640_REG_AEC_PK_MANUAL,
+		       0x3, on ? 0 : 0x3);
+	return 0;
+}
+
+static int ov5640_set_test_pattern(struct ov5640_dev *sensor, int value)
+{
+	ov5640_mod_reg(sensor, OV5640_REG_PRE_ISP_TEST_SET1,
+		       0xa4, value ? 0xa4 : 0);
+	return 0;
+}
+
+static int ov5640_set_stream(struct ov5640_dev *sensor, bool on)
+{
+	ov5640_mod_reg(sensor, OV5640_REG_MIPI_CTRL00, BIT(5),
+		       on ? 0 : BIT(5));
+	ov5640_write_reg(sensor, OV5640_REG_PAD_OUTPUT00,
+			 on ? 0x00 : 0x70);
+	ov5640_write_reg(sensor, OV5640_REG_FRAME_CTRL01,
+			 on ? 0x00 : 0x0f);
+	return 0;
+}
+
+static int ov5640_get_sysclk(struct ov5640_dev *sensor)
+{
+	 /* calculate sysclk */
+	u32 xvclk = sensor->xclk_freq / 10000;
+	u32 multiplier, prediv, VCO, sysdiv, pll_rdiv;
+	u32 sclk_rdiv_map[] = {1, 2, 4, 8};
+	u32 bit_div2x = 1, sclk_rdiv, sysclk;
+	u8 temp1, temp2;
+
+	ov5640_read_reg(sensor, OV5640_REG_SC_PLL_CTRL0, &temp1);
+	temp2 = temp1 & 0x0f;
+	if (temp2 == 8 || temp2 == 10)
+		bit_div2x = temp2 / 2;
+
+	ov5640_read_reg(sensor, OV5640_REG_SC_PLL_CTRL1, &temp1);
+	sysdiv = temp1 >> 4;
+	if (sysdiv == 0)
+		sysdiv = 16;
+
+	ov5640_read_reg(sensor, OV5640_REG_SC_PLL_CTRL2, &temp1);
+	multiplier = temp1;
+
+	ov5640_read_reg(sensor, OV5640_REG_SC_PLL_CTRL3, &temp1);
+	prediv = temp1 & 0x0f;
+	pll_rdiv = ((temp1 >> 4) & 0x01) + 1;
+
+	ov5640_read_reg(sensor, OV5640_REG_SYS_ROOT_DIVIDER, &temp1);
+	temp2 = temp1 & 0x03;
+	sclk_rdiv = sclk_rdiv_map[temp2];
+
+	VCO = xvclk * multiplier / prediv;
+
+	sysclk = VCO / sysdiv / pll_rdiv * 2 / bit_div2x / sclk_rdiv;
+
+	return sysclk;
+}
+
+static int ov5640_set_night_mode(struct ov5640_dev *sensor)
+{
+	 /* read HTS from register settings */
+	u8 mode;
+
+	ov5640_read_reg(sensor, OV5640_REG_AEC_CTRL00, &mode);
+	mode &= 0xfb;
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL00, mode);
+	return 0;
+}
+
+static int ov5640_get_hts(struct ov5640_dev *sensor)
+{
+	/* read HTS from register settings */
+	u16 hts;
+
+	ov5640_read_reg16(sensor, OV5640_REG_TIMING_HTS, &hts);
+	return hts;
+}
+
+static int ov5640_get_vts(struct ov5640_dev *sensor)
+{
+	u16 vts;
+
+	ov5640_read_reg16(sensor, OV5640_REG_TIMING_VTS, &vts);
+	return vts;
+}
+
+static int ov5640_set_vts(struct ov5640_dev *sensor, int vts)
+{
+	ov5640_write_reg16(sensor, OV5640_REG_TIMING_VTS, vts);
+	return 0;
+}
+
+static int ov5640_get_light_freq(struct ov5640_dev *sensor)
+{
+	/* get banding filter value */
+	u8 temp, temp1;
+	int light_freq = 0;
+
+	ov5640_read_reg(sensor, OV5640_REG_HZ5060_CTRL01, &temp);
+
+	if (temp & 0x80) {
+		/* manual */
+		ov5640_read_reg(sensor, OV5640_REG_HZ5060_CTRL00, &temp1);
+		if (temp1 & 0x04) {
+			/* 50Hz */
+			light_freq = 50;
+		} else {
+			/* 60Hz */
+			light_freq = 60;
+		}
+	} else {
+		/* auto */
+		ov5640_read_reg(sensor, OV5640_REG_SIGMADELTA_CTRL0C,
+				&temp1);
+		if (temp1 & 0x01) {
+			/* 50Hz */
+			light_freq = 50;
+		} else {
+			/* 60Hz */
+		}
+	}
+
+	return light_freq;
+}
+
+static int ov5640_set_bandingfilter(struct ov5640_dev *sensor)
+{
+	u32 band_step60, max_band60, band_step50, max_band50, prev_vts;
+	int ret;
+
+	/* read preview PCLK */
+	ret = ov5640_get_sysclk(sensor);
+	if (ret < 0)
+		return ret;
+	sensor->prev_sysclk = ret;
+	/* read preview HTS */
+	ret = ov5640_get_hts(sensor);
+	if (ret < 0)
+		return ret;
+	sensor->prev_hts = ret;
+
+	/* read preview VTS */
+	ret = ov5640_get_vts(sensor);
+	if (ret < 0)
+		return ret;
+	prev_vts = ret;
+
+	/* calculate banding filter */
+	/* 60Hz */
+	band_step60 = sensor->prev_sysclk * 100 / sensor->prev_hts * 100/120;
+	ov5640_write_reg16(sensor, OV5640_REG_AEC_B60_STEP, band_step60);
+
+	max_band60 = (int)((prev_vts-4)/band_step60);
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL0D, max_band60);
+
+	/* 50Hz */
+	band_step50 = sensor->prev_sysclk * 100 / sensor->prev_hts;
+	ov5640_write_reg16(sensor, OV5640_REG_AEC_B50_STEP, band_step50);
+
+	max_band50 = (int)((prev_vts-4)/band_step50);
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL0E, max_band50);
+
+	return 0;
+}
+
+static int ov5640_set_ae_target(struct ov5640_dev *sensor, int target)
+{
+	/* stable in high */
+	u32 fast_high, fast_low;
+
+	sensor->ae_low = target * 23 / 25;	/* 0.92 */
+	sensor->ae_high = target * 27 / 25;	/* 1.08 */
+
+	fast_high = sensor->ae_high << 1;
+	if (fast_high > 255)
+		fast_high = 255;
+
+	fast_low = sensor->ae_low >> 1;
+
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL0F, sensor->ae_high);
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL10, sensor->ae_low);
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL1B, sensor->ae_high);
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL1E, sensor->ae_low);
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL11, fast_high);
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL1F, fast_low);
+
+	return 0;
+}
+
+static int ov5640_binning_on(struct ov5640_dev *sensor)
+{
+	u8 temp;
+
+	ov5640_read_reg(sensor, OV5640_REG_TIMING_TC_REG21, &temp);
+	temp &= 0xfe;
+
+	return temp ? 1 : 0;
+}
+
+static int ov5640_set_virtual_channel(struct ov5640_dev *sensor)
+{
+	u8 temp, channel = OV5640_MIPI_VC;
+
+	ov5640_read_reg(sensor, OV5640_REG_DEBUG_MODE, &temp);
+	temp &= ~(3 << 6);
+	temp |= (channel << 6);
+	ov5640_write_reg(sensor, OV5640_REG_DEBUG_MODE, temp);
+
+	return 0;
+}
+
+static const struct ov5640_mode_info *
+ov5640_find_mode(struct ov5640_dev *sensor, enum ov5640_frame_rate fr,
+		 int width, int height, bool nearest)
+{
+	const struct ov5640_mode_info *mode = NULL;
+	int i;
+
+	for (i = OV5640_NUM_MODES - 1; i >= 0; i--) {
+		mode = &ov5640_mode_data[fr][i];
+
+		if (!mode->reg_data)
+			continue;
+
+		if ((nearest && mode->width <= width &&
+		     mode->height <= height) ||
+		    (!nearest && mode->width == width &&
+		     mode->height == height))
+			break;
+	}
+
+	if (nearest && i < 0)
+		mode = &ov5640_mode_data[fr][0];
+
+	return mode;
+}
+
+/*
+ * sensor changes between scaling and subsampling, go through
+ * exposure calculation
+ */
+static int ov5640_set_mode_exposure_calc(
+	struct ov5640_dev *sensor, const struct ov5640_mode_info *mode)
+{
+	u32 prev_shutter, prev_gain16;
+	u32 cap_shutter, cap_gain16;
+	u32 cap_sysclk, cap_hts, cap_vts;
+	u32 light_freq, cap_bandfilt, cap_maxband;
+	u32 cap_gain16_shutter;
+	u8 average;
+	int ret;
+
+	if (mode->reg_data == NULL)
+		return -EINVAL;
+
+	/* turn off AE/AG */
+	ret = ov5640_set_agc_aec(sensor, false);
+	if (ret < 0)
+		return ret;
+
+	/* read preview shutter */
+	ret = ov5640_get_exposure(sensor);
+	if (ret < 0)
+		return ret;
+	prev_shutter = ret;
+	ret = ov5640_binning_on(sensor);
+	if (ret < 0)
+		return ret;
+	if (ret && mode->id != OV5640_MODE_720P_1280_720 &&
+	    mode->id != OV5640_MODE_1080P_1920_1080)
+		prev_shutter *= 2;
+
+	/* read preview gain */
+	ret = ov5640_get_gain(sensor);
+	if (ret < 0)
+		return ret;
+	prev_gain16 = ret;
+
+	/* get average */
+	ov5640_read_reg(sensor, OV5640_REG_AVG_READOUT, &average);
+
+	/* turn off night mode for capture */
+	ret = ov5640_set_night_mode(sensor);
+	if (ret < 0)
+		return ret;
+
+	/* Write capture setting */
+	ret = ov5640_load_regs(sensor, mode);
+	if (ret < 0)
+		return ret;
+
+	/* read capture VTS */
+	ret = ov5640_get_vts(sensor);
+	if (ret < 0)
+		return ret;
+	cap_vts = ret;
+	ret = ov5640_get_hts(sensor);
+	if (ret < 0)
+		return ret;
+	cap_hts = ret;
+	ret = ov5640_get_sysclk(sensor);
+	if (ret < 0)
+		return ret;
+	cap_sysclk = ret;
+
+	/* calculate capture banding filter */
+	ret = ov5640_get_light_freq(sensor);
+	if (ret < 0)
+		return ret;
+	light_freq = ret;
+
+	if (light_freq == 60) {
+		/* 60Hz */
+		cap_bandfilt = cap_sysclk * 100 / cap_hts * 100 / 120;
+	} else {
+		/* 50Hz */
+		cap_bandfilt = cap_sysclk * 100 / cap_hts;
+	}
+	cap_maxband = (int)((cap_vts - 4) / cap_bandfilt);
+
+	/* calculate capture shutter/gain16 */
+	if (average > sensor->ae_low && average < sensor->ae_high) {
+		/* in stable range */
+		cap_gain16_shutter =
+			prev_gain16 * prev_shutter *
+			cap_sysclk / sensor->prev_sysclk *
+			sensor->prev_hts / cap_hts *
+			sensor->ae_target / average;
+	} else {
+		cap_gain16_shutter =
+			prev_gain16 * prev_shutter *
+			cap_sysclk / sensor->prev_sysclk *
+			sensor->prev_hts / cap_hts;
+	}
+
+	/* gain to shutter */
+	if (cap_gain16_shutter < (cap_bandfilt * 16)) {
+		/* shutter < 1/100 */
+		cap_shutter = cap_gain16_shutter / 16;
+		if (cap_shutter < 1)
+			cap_shutter = 1;
+
+		cap_gain16 = cap_gain16_shutter / cap_shutter;
+		if (cap_gain16 < 16)
+			cap_gain16 = 16;
+	} else {
+		if (cap_gain16_shutter > (cap_bandfilt * cap_maxband * 16)) {
+			/* exposure reach max */
+			cap_shutter = cap_bandfilt * cap_maxband;
+			cap_gain16 = cap_gain16_shutter / cap_shutter;
+		} else {
+			/* 1/100 < (cap_shutter = n/100) =< max */
+			cap_shutter =
+				((int)(cap_gain16_shutter / 16 / cap_bandfilt))
+				* cap_bandfilt;
+			cap_gain16 = cap_gain16_shutter / cap_shutter;
+		}
+	}
+
+	/* write capture gain */
+	ret = ov5640_set_gain(sensor, cap_gain16);
+	if (ret < 0)
+		return ret;
+
+	/* write capture shutter */
+	if (cap_shutter > (cap_vts - 4)) {
+		cap_vts = cap_shutter + 4;
+		ret = ov5640_set_vts(sensor, cap_vts);
+		if (ret < 0)
+			return ret;
+	}
+
+	return ov5640_set_exposure(sensor, cap_shutter);
+}
+
+/*
+ * if sensor changes inside scaling or subsampling
+ * change mode directly
+ */
+static int ov5640_set_mode_direct(struct ov5640_dev *sensor,
+				  const struct ov5640_mode_info *mode)
+{
+	int ret;
+
+	if (mode->reg_data == NULL)
+		return -EINVAL;
+
+	/* turn off AE/AG */
+	ret = ov5640_set_agc_aec(sensor, false);
+	if (ret < 0)
+		return ret;
+
+	/* Write capture setting */
+	ret = ov5640_load_regs(sensor, mode);
+	if (ret < 0)
+		return ret;
+
+	return ov5640_set_agc_aec(sensor, true);
+}
+
+static int ov5640_set_mode(struct ov5640_dev *sensor,
+			   const struct ov5640_mode_info *orig_mode)
+{
+	const struct ov5640_mode_info *mode = sensor->current_mode;
+	enum ov5640_downsize_mode dn_mode, orig_dn_mode;
+	int ret;
+
+	dn_mode = mode->dn_mode;
+	orig_dn_mode = orig_mode->dn_mode;
+
+	if ((dn_mode == SUBSAMPLING && orig_dn_mode == SCALING) ||
+	    (dn_mode == SCALING && orig_dn_mode == SUBSAMPLING)) {
+		/*
+		 * change between subsampling and scaling
+		 * go through exposure calucation
+		 */
+		ret = ov5640_set_mode_exposure_calc(sensor, mode);
+	} else {
+		/*
+		 * change inside subsampling or scaling
+		 * download firmware directly
+		 */
+		ret = ov5640_set_mode_direct(sensor, mode);
+	}
+
+	if (ret < 0)
+		return ret;
+
+	ret = ov5640_set_ae_target(sensor, sensor->ae_target);
+	if (ret < 0)
+		return ret;
+	ret = ov5640_get_light_freq(sensor);
+	if (ret < 0)
+		return ret;
+	ret = ov5640_set_bandingfilter(sensor);
+	if (ret < 0)
+		return ret;
+	ret = ov5640_set_virtual_channel(sensor);
+	if (ret < 0)
+		return ret;
+
+	sensor->pending_mode_change = false;
+
+	return 0;
+}
+
+/* restore the last set video mode after chip power-on */
+static int ov5640_restore_mode(struct ov5640_dev *sensor)
+{
+	int ret;
+
+	/* first load the initial register values */
+	ret = ov5640_load_regs(sensor, &ov5640_mode_init_data);
+	if (ret < 0)
+		return ret;
+
+	/* now restore the last capture mode */
+	return ov5640_set_mode(sensor, &ov5640_mode_init_data);
+}
+
+static void ov5640_power(struct ov5640_dev *sensor, bool enable)
+{
+	if (sensor->pwdn_gpio)
+		gpiod_set_value(sensor->pwdn_gpio, enable ? 0 : 1);
+}
+
+static void ov5640_reset(struct ov5640_dev *sensor)
+{
+	if (!sensor->reset_gpio)
+		return;
+
+	gpiod_set_value(sensor->reset_gpio, 0);
+
+	/* camera power cycle */
+	ov5640_power(sensor, false);
+	usleep_range(5000, 10000);
+	ov5640_power(sensor, true);
+	usleep_range(5000, 10000);
+
+	gpiod_set_value(sensor->reset_gpio, 1);
+	usleep_range(1000, 2000);
+
+	gpiod_set_value(sensor->reset_gpio, 0);
+	usleep_range(5000, 10000);
+}
+
+static int ov5640_set_power(struct ov5640_dev *sensor, bool on)
+{
+	int ret = 0;
+
+	if (on) {
+		clk_prepare_enable(sensor->xclk);
+
+		ret = regulator_bulk_enable(OV5640_NUM_SUPPLIES,
+					    sensor->supplies);
+		if (ret)
+			goto xclk_off;
+
+		ov5640_reset(sensor);
+		ov5640_power(sensor, true);
+
+		ret = ov5640_init_slave_id(sensor);
+		if (ret)
+			goto power_off;
+
+		ret = ov5640_restore_mode(sensor);
+		if (ret)
+			goto power_off;
+
+		/*
+		 * start streaming briefly followed by stream off in
+		 * order to coax the clock lane into LP-11 state.
+		 */
+		ov5640_set_stream(sensor, true);
+		usleep_range(1000, 2000);
+		ov5640_set_stream(sensor, false);
+
+		return 0;
+	}
+
+power_off:
+	ov5640_power(sensor, false);
+	regulator_bulk_disable(OV5640_NUM_SUPPLIES, sensor->supplies);
+xclk_off:
+	clk_disable_unprepare(sensor->xclk);
+	return ret;
+}
+
+/* --------------- Subdev Operations --------------- */
+
+static int ov5640_s_power(struct v4l2_subdev *sd, int on)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	int ret = 0;
+
+	mutex_lock(&sensor->lock);
+
+	/*
+	 * If the power count is modified from 0 to != 0 or from != 0 to 0,
+	 * update the power state.
+	 */
+	if (sensor->power_count == !on) {
+		ret = ov5640_set_power(sensor, !!on);
+		if (ret)
+			goto out;
+	}
+
+	/* Update the power count. */
+	sensor->power_count += on ? 1 : -1;
+	WARN_ON(sensor->power_count < 0);
+out:
+	mutex_unlock(&sensor->lock);
+
+	if (on && !ret && sensor->power_count == 1) {
+		/* restore controls */
+		ret = v4l2_ctrl_handler_setup(&sensor->ctrls.handler);
+	}
+
+	return ret;
+}
+
+static int ov5640_try_frame_interval(struct ov5640_dev *sensor,
+				     struct v4l2_fract *fi,
+				     u32 width, u32 height)
+{
+	const struct ov5640_mode_info *mode;
+	u32 minfps, maxfps, fps;
+	int ret;
+
+	minfps = ov5640_framerates[OV5640_15_FPS];
+	maxfps = ov5640_framerates[OV5640_30_FPS];
+
+	if (fi->numerator == 0) {
+		fi->denominator = maxfps;
+		fi->numerator = 1;
+		return OV5640_30_FPS;
+	}
+
+	fps = DIV_ROUND_CLOSEST(fi->denominator, fi->numerator);
+
+	fi->numerator = 1;
+	if (fps > maxfps)
+		fi->denominator = maxfps;
+	else if (fps < minfps)
+		fi->denominator = minfps;
+	else if (2 * fps >= 2 * minfps + (maxfps - minfps))
+		fi->denominator = maxfps;
+	else
+		fi->denominator = minfps;
+
+	ret = (fi->denominator == minfps) ? OV5640_15_FPS : OV5640_30_FPS;
+
+	mode = ov5640_find_mode(sensor, ret, width, height, false);
+	return mode ? ret : -EINVAL;
+}
+
+static int ov5640_g_parm(struct v4l2_subdev *sd, struct v4l2_streamparm *a)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	struct v4l2_captureparm *cparm = &a->parm.capture;
+
+	if (a->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+		return -EINVAL;
+
+	mutex_lock(&sensor->lock);
+
+	/* This is the only case currently handled. */
+	memset(a, 0, sizeof(*a));
+	a->type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
+	cparm->capability = sensor->streamcap.capability;
+	cparm->timeperframe = sensor->streamcap.timeperframe;
+	cparm->capturemode = sensor->streamcap.capturemode;
+
+	mutex_unlock(&sensor->lock);
+
+	return 0;
+}
+
+static int ov5640_s_parm(struct v4l2_subdev *sd, struct v4l2_streamparm *a)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	struct v4l2_fract *tpf = &a->parm.capture.timeperframe;
+	const struct ov5640_mode_info *mode;
+	int frame_rate, ret = 0;
+
+	if (a->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+		return -EINVAL;
+
+	mutex_lock(&sensor->lock);
+
+	if (sensor->streaming) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	mode = sensor->current_mode;
+
+	frame_rate = ov5640_try_frame_interval(sensor, tpf,
+					       mode->width, mode->height);
+	if (frame_rate < 0) {
+		ret = frame_rate;
+		goto out;
+	}
+
+	sensor->current_fr = frame_rate;
+	sensor->streamcap.timeperframe = *tpf;
+	sensor->pending_mode_change = true;
+out:
+	mutex_unlock(&sensor->lock);
+	return 0;
+}
+
+static int ov5640_get_fmt(struct v4l2_subdev *sd,
+			  struct v4l2_subdev_pad_config *cfg,
+			  struct v4l2_subdev_format *format)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	struct v4l2_mbus_framefmt *fmt;
+
+	if (format->pad != 0)
+		return -EINVAL;
+
+	mutex_lock(&sensor->lock);
+
+	if (format->which == V4L2_SUBDEV_FORMAT_TRY)
+		fmt = v4l2_subdev_get_try_format(&sensor->sd, cfg,
+						 format->pad);
+	else
+		fmt = &sensor->fmt;
+
+	format->format = *fmt;
+
+	mutex_unlock(&sensor->lock);
+
+	return 0;
+}
+
+static int ov5640_try_fmt_internal(struct v4l2_subdev *sd,
+				   struct v4l2_mbus_framefmt *fmt,
+				   enum ov5640_frame_rate fr,
+				   const struct ov5640_mode_info **new_mode)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	const struct ov5640_mode_info *mode;
+
+	mode = ov5640_find_mode(sensor, fr, fmt->width, fmt->height, true);
+	if (!mode)
+		return -EINVAL;
+
+	fmt->width = mode->width;
+	fmt->height = mode->height;
+	fmt->code = sensor->fmt.code;
+
+	if (new_mode)
+		*new_mode = mode;
+	return 0;
+}
+
+static int ov5640_set_fmt(struct v4l2_subdev *sd,
+			  struct v4l2_subdev_pad_config *cfg,
+			  struct v4l2_subdev_format *format)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	const struct ov5640_mode_info *new_mode;
+	int ret;
+
+	if (format->pad != 0)
+		return -EINVAL;
+
+	mutex_lock(&sensor->lock);
+
+	if (sensor->streaming) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	ret = ov5640_try_fmt_internal(sd, &format->format,
+				      sensor->current_fr, &new_mode);
+	if (ret)
+		goto out;
+
+	if (format->which == V4L2_SUBDEV_FORMAT_TRY) {
+		struct v4l2_mbus_framefmt *fmt =
+			v4l2_subdev_get_try_format(sd, cfg, 0);
+
+		*fmt = format->format;
+		goto out;
+	}
+
+	sensor->current_mode = new_mode;
+	sensor->fmt = format->format;
+	sensor->pending_mode_change = true;
+out:
+	mutex_unlock(&sensor->lock);
+	return ret;
+}
+
+
+/*
+ * Sensor Controls.
+ */
+
+static int ov5640_g_volatile_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct v4l2_subdev *sd = ctrl_to_sd(ctrl);
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+
+	mutex_lock(&sensor->lock);
+
+	switch (ctrl->id) {
+	case V4L2_CID_AUTOGAIN:
+		if (!ctrl->val)
+			goto out;
+		sensor->ctrls.gain->val = ov5640_get_gain(sensor);
+		break;
+	case V4L2_CID_EXPOSURE_AUTO:
+		if (ctrl->val == V4L2_EXPOSURE_MANUAL)
+			goto out;
+		sensor->ctrls.exposure->val = ov5640_get_exposure(sensor);
+		break;
+	}
+
+out:
+	mutex_unlock(&sensor->lock);
+	return 0;
+}
+
+static int ov5640_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct v4l2_subdev *sd = ctrl_to_sd(ctrl);
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	int ret = 0;
+
+	mutex_lock(&sensor->lock);
+
+	/*
+	 * If the device is not powered up by the host driver do
+	 * not apply any controls to H/W at this time. Instead
+	 * the controls will be restored right after power-up.
+	 */
+	if (sensor->power_count == 0)
+		goto out;
+
+	switch (ctrl->id) {
+	case V4L2_CID_AUTOGAIN:
+		ret = ov5640_set_gain(sensor, ctrl->val);
+		break;
+	case V4L2_CID_EXPOSURE_AUTO:
+		ret = ov5640_set_exposure(sensor, ctrl->val);
+		break;
+	case V4L2_CID_AUTO_WHITE_BALANCE:
+		ret = ov5640_set_white_balance(sensor, ctrl->val);
+		break;
+	case V4L2_CID_HUE:
+		ret = ov5640_set_hue(sensor, ctrl->val);
+		break;
+	case V4L2_CID_CONTRAST:
+		ret = ov5640_set_contrast(sensor, ctrl->val);
+		break;
+	case V4L2_CID_SATURATION:
+		ret = ov5640_set_saturation(sensor, ctrl->val);
+		break;
+	case V4L2_CID_TEST_PATTERN:
+		ret = ov5640_set_test_pattern(sensor, ctrl->val);
+		break;
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+out:
+	mutex_unlock(&sensor->lock);
+	return ret;
+}
+
+static const struct v4l2_ctrl_ops ov5640_ctrl_ops = {
+	.g_volatile_ctrl = ov5640_g_volatile_ctrl,
+	.s_ctrl = ov5640_s_ctrl,
+};
+
+static const char * const test_pattern_menu[] = {
+	"Disabled",
+	"Color bars",
+};
+
+static int ov5640_init_controls(struct ov5640_dev *sensor)
+{
+	const struct v4l2_ctrl_ops *ops = &ov5640_ctrl_ops;
+	struct ov5640_ctrls *ctrls = &sensor->ctrls;
+	struct v4l2_ctrl_handler *hdl = &ctrls->handler;
+	int ret;
+
+	v4l2_ctrl_handler_init(hdl, 32);
+
+	/* Auto/manual white balance */
+	ctrls->auto_wb = v4l2_ctrl_new_std(hdl, ops,
+					   V4L2_CID_AUTO_WHITE_BALANCE,
+					   0, 1, 1, 1);
+	ctrls->blue_balance = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_BLUE_BALANCE,
+						0, 4095, 1, 0);
+	ctrls->red_balance = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_RED_BALANCE,
+					       0, 4095, 1, 0);
+	/* Auto/manual exposure */
+	ctrls->auto_exp = v4l2_ctrl_new_std_menu(hdl, ops,
+						 V4L2_CID_EXPOSURE_AUTO,
+						 V4L2_EXPOSURE_MANUAL, 0,
+						 V4L2_EXPOSURE_AUTO);
+	ctrls->exposure = v4l2_ctrl_new_std(hdl, ops,
+					    V4L2_CID_EXPOSURE_ABSOLUTE,
+					    0, 65535, 1, 0);
+	/* Auto/manual gain */
+	ctrls->auto_gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_AUTOGAIN,
+					     0, 1, 1, 1);
+	ctrls->gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_GAIN,
+					0, 1023, 1, 0);
+
+	ctrls->saturation = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_SATURATION,
+					      0, 255, 1, 64);
+	ctrls->hue = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_HUE,
+				       0, 359, 1, 0);
+	ctrls->contrast = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_CONTRAST,
+					    0, 255, 1, 0);
+	ctrls->test_pattern =
+		v4l2_ctrl_new_std_menu_items(hdl, ops, V4L2_CID_TEST_PATTERN,
+					     ARRAY_SIZE(test_pattern_menu) - 1,
+					     0, 0, test_pattern_menu);
+
+	if (hdl->error) {
+		ret = hdl->error;
+		goto free_ctrls;
+	}
+
+	ctrls->gain->flags |= V4L2_CTRL_FLAG_VOLATILE;
+	ctrls->exposure->flags |= V4L2_CTRL_FLAG_VOLATILE;
+
+	v4l2_ctrl_auto_cluster(3, &ctrls->auto_wb, 0, false);
+	v4l2_ctrl_auto_cluster(2, &ctrls->auto_gain, 0, true);
+	v4l2_ctrl_auto_cluster(2, &ctrls->auto_exp, 1, true);
+
+	sensor->sd.ctrl_handler = hdl;
+	return 0;
+
+free_ctrls:
+	v4l2_ctrl_handler_free(hdl);
+	return ret;
+}
+
+static int ov5640_enum_frame_size(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_pad_config *cfg,
+				  struct v4l2_subdev_frame_size_enum *fse)
+{
+	if (fse->pad != 0)
+		return -EINVAL;
+	if (fse->index >= OV5640_NUM_MODES)
+		return -EINVAL;
+
+	fse->min_width = fse->max_width =
+		ov5640_mode_data[0][fse->index].width;
+	fse->min_height = fse->max_height =
+		ov5640_mode_data[0][fse->index].height;
+
+	return 0;
+}
+
+static int ov5640_enum_frame_interval(
+	struct v4l2_subdev *sd,
+	struct v4l2_subdev_pad_config *cfg,
+	struct v4l2_subdev_frame_interval_enum *fie)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	struct v4l2_fract tpf;
+	int ret;
+
+	if (fie->pad != 0)
+		return -EINVAL;
+	if (fie->index >= OV5640_NUM_FRAMERATES)
+		return -EINVAL;
+
+	tpf.numerator = 1;
+	tpf.denominator = ov5640_framerates[fie->index];
+
+	ret = ov5640_try_frame_interval(sensor, &tpf,
+					fie->width, fie->height);
+	if (ret < 0)
+		return -EINVAL;
+
+	fie->interval = tpf;
+	return 0;
+}
+
+static int ov5640_g_frame_interval(struct v4l2_subdev *sd,
+				   struct v4l2_subdev_frame_interval *fi)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+
+	mutex_lock(&sensor->lock);
+	fi->interval = sensor->streamcap.timeperframe;
+	mutex_unlock(&sensor->lock);
+
+	return 0;
+}
+
+static int ov5640_s_frame_interval(struct v4l2_subdev *sd,
+				   struct v4l2_subdev_frame_interval *fi)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	const struct ov5640_mode_info *mode;
+	int frame_rate, ret = 0;
+
+	if (fi->pad != 0)
+		return -EINVAL;
+
+	mutex_lock(&sensor->lock);
+
+	if (sensor->streaming) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	mode = sensor->current_mode;
+
+	frame_rate = ov5640_try_frame_interval(sensor, &fi->interval,
+					       mode->width, mode->height);
+	if (frame_rate < 0)
+		frame_rate = OV5640_15_FPS;
+
+	sensor->current_fr = frame_rate;
+	sensor->streamcap.timeperframe = fi->interval;
+	sensor->pending_mode_change = true;
+out:
+	mutex_unlock(&sensor->lock);
+	return ret;
+}
+
+static int ov5640_enum_mbus_code(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_pad_config *cfg,
+				  struct v4l2_subdev_mbus_code_enum *code)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+
+	if (code->pad != 0)
+		return -EINVAL;
+	if (code->index != 0)
+		return -EINVAL;
+
+	code->code = sensor->fmt.code;
+
+	return 0;
+}
+
+static int ov5640_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	int ret = 0;
+
+	mutex_lock(&sensor->lock);
+
+	if (sensor->streaming == !enable) {
+		if (enable && sensor->pending_mode_change) {
+			ret = ov5640_set_mode(sensor, sensor->current_mode);
+			if (ret)
+				goto out;
+		}
+
+		ret = ov5640_set_stream(sensor, enable);
+		if (!ret)
+			sensor->streaming = enable;
+	}
+out:
+	mutex_unlock(&sensor->lock);
+	return ret;
+}
+
+static const struct v4l2_subdev_core_ops ov5640_core_ops = {
+	.s_power = ov5640_s_power,
+};
+
+static const struct v4l2_subdev_video_ops ov5640_video_ops = {
+	.s_parm = ov5640_s_parm,
+	.g_parm = ov5640_g_parm,
+	.g_frame_interval = ov5640_g_frame_interval,
+	.s_frame_interval = ov5640_s_frame_interval,
+	.s_stream = ov5640_s_stream,
+};
+
+static const struct v4l2_subdev_pad_ops ov5640_pad_ops = {
+	.enum_mbus_code = ov5640_enum_mbus_code,
+	.get_fmt = ov5640_get_fmt,
+	.set_fmt = ov5640_set_fmt,
+	.enum_frame_size = ov5640_enum_frame_size,
+	.enum_frame_interval = ov5640_enum_frame_interval,
+};
+
+static const struct v4l2_subdev_ops ov5640_subdev_ops = {
+	.core = &ov5640_core_ops,
+	.video = &ov5640_video_ops,
+	.pad = &ov5640_pad_ops,
+};
+
+static int ov5640_get_regulators(struct ov5640_dev *sensor)
+{
+	int i;
+
+	for (i = 0; i < OV5640_NUM_SUPPLIES; i++)
+		sensor->supplies[i].supply = ov5640_supply_name[i];
+
+	return devm_regulator_bulk_get(&sensor->i2c_client->dev,
+				       OV5640_NUM_SUPPLIES,
+				       sensor->supplies);
+}
+
+static int ov5640_probe(struct i2c_client *client,
+			const struct i2c_device_id *id)
+{
+	struct device *dev = &client->dev;
+	struct device_node *endpoint;
+	struct ov5640_dev *sensor;
+	int ret;
+
+	sensor = devm_kzalloc(dev, sizeof(*sensor), GFP_KERNEL);
+	if (!sensor)
+		return -ENOMEM;
+
+	sensor->i2c_client = client;
+	sensor->fmt.code = MEDIA_BUS_FMT_UYVY8_2X8;
+	sensor->fmt.width = 640;
+	sensor->fmt.height = 480;
+	sensor->fmt.field = V4L2_FIELD_NONE;
+	sensor->streamcap.capability = V4L2_CAP_TIMEPERFRAME;
+	sensor->streamcap.capturemode = 0;
+	sensor->streamcap.timeperframe.denominator =
+		ov5640_framerates[OV5640_30_FPS];
+	sensor->streamcap.timeperframe.numerator = 1;
+	sensor->current_fr = OV5640_30_FPS;
+	sensor->current_mode =
+		&ov5640_mode_data[OV5640_30_FPS][OV5640_MODE_VGA_640_480];
+	sensor->pending_mode_change = true;
+
+	sensor->ae_target = 52;
+
+	endpoint = of_graph_get_next_endpoint(client->dev.of_node, NULL);
+	if (!endpoint) {
+		dev_err(dev, "endpoint node not found\n");
+		return -EINVAL;
+	}
+
+	v4l2_of_parse_endpoint(endpoint, &sensor->ep);
+	of_node_put(endpoint);
+
+	if (sensor->ep.bus_type != V4L2_MBUS_CSI2) {
+		dev_err(dev, "invalid bus type, must be MIPI CSI2\n");
+		return -EINVAL;
+	}
+
+	/* get system clock (xclk) */
+	sensor->xclk = devm_clk_get(dev, "xclk");
+	if (IS_ERR(sensor->xclk)) {
+		dev_err(dev, "failed to get xclk\n");
+		return PTR_ERR(sensor->xclk);
+	}
+
+	sensor->xclk_freq = clk_get_rate(sensor->xclk);
+	if (sensor->xclk_freq < OV5640_XCLK_MIN ||
+	    sensor->xclk_freq > OV5640_XCLK_MAX) {
+		dev_err(dev, "xclk frequency out of range: %d Hz\n",
+			sensor->xclk_freq);
+		return -EINVAL;
+	}
+
+	/* request optional power down pin */
+	sensor->pwdn_gpio = devm_gpiod_get_optional(dev, "powerdown",
+						    GPIOD_OUT_HIGH);
+	/* request optional reset pin */
+	sensor->reset_gpio = devm_gpiod_get_optional(dev, "reset",
+						     GPIOD_OUT_HIGH);
+
+	v4l2_i2c_subdev_init(&sensor->sd, client, &ov5640_subdev_ops);
+
+	sensor->sd.flags = V4L2_SUBDEV_FL_HAS_DEVNODE;
+	sensor->pad.flags = MEDIA_PAD_FL_SOURCE;
+	sensor->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
+	ret = media_entity_pads_init(&sensor->sd.entity, 1, &sensor->pad);
+	if (ret)
+		return ret;
+
+	ret = ov5640_get_regulators(sensor);
+	if (ret)
+		return ret;
+
+	mutex_init(&sensor->lock);
+
+	ret = ov5640_init_controls(sensor);
+	if (ret)
+		goto entity_cleanup;
+
+	ret = v4l2_async_register_subdev(&sensor->sd);
+	if (ret)
+		goto free_ctrls;
+
+	return 0;
+
+free_ctrls:
+	v4l2_ctrl_handler_free(&sensor->ctrls.handler);
+entity_cleanup:
+	mutex_destroy(&sensor->lock);
+	media_entity_cleanup(&sensor->sd.entity);
+	regulator_bulk_disable(OV5640_NUM_SUPPLIES, sensor->supplies);
+	return ret;
+}
+
+static int ov5640_remove(struct i2c_client *client)
+{
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+
+	regulator_bulk_disable(OV5640_NUM_SUPPLIES, sensor->supplies);
+
+	v4l2_async_unregister_subdev(&sensor->sd);
+	mutex_destroy(&sensor->lock);
+	media_entity_cleanup(&sensor->sd.entity);
+	v4l2_ctrl_handler_free(&sensor->ctrls.handler);
+
+	return 0;
+}
+
+static const struct i2c_device_id ov5640_id[] = {
+	{"ov5640", 0},
+	{},
+};
+MODULE_DEVICE_TABLE(i2c, ov5640_id);
+
+static const struct of_device_id ov5640_dt_ids[] = {
+	{ .compatible = "ovti,ov5640" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, ov5640_dt_ids);
+
+static struct i2c_driver ov5640_i2c_driver = {
+	.driver = {
+		.name  = "ov5640",
+		.of_match_table	= ov5640_dt_ids,
+	},
+	.id_table = ov5640_id,
+	.probe    = ov5640_probe,
+	.remove   = ov5640_remove,
+};
+
+module_i2c_driver(ov5640_i2c_driver);
+
+MODULE_DESCRIPTION("OV5640 MIPI Camera Subdev Driver");
+MODULE_LICENSE("GPL");
-- 
2.7.4

[PATCH v5 19/39] [media] add Omnivision OV5640 sensor driver

[Steve Longerbeam]

This driver is based on ov5640_mipi.c from Freescale imx_3.10.17_1.0.0_beta
branch, modified heavily to bring forward to latest interfaces and code
cleanup.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/media/i2c/Kconfig  |    7 +
 drivers/media/i2c/Makefile |    1 +
 drivers/media/i2c/ov5640.c | 2231 ++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 2239 insertions(+)
 create mode 100644 drivers/media/i2c/ov5640.c

diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index cee1dae..bf67661 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -531,6 +531,13 @@ config VIDEO_OV2659
 	  To compile this driver as a module, choose M here: the
 	  module will be called ov2659.
 
+config VIDEO_OV5640
+	tristate "OmniVision OV5640 sensor support"
+	depends on GPIOLIB && VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API
+	---help---
+	  This is a V4L2 sensor-level driver for the Omnivision
+	  OV5640 camera sensor with a MIPI CSI-2 interface.
+
 config VIDEO_OV7640
 	tristate "OmniVision OV7640 sensor support"
 	depends on I2C && VIDEO_V4L2
diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index 5bc7bbe..3a9d73a 100644
--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -57,6 +57,7 @@ obj-$(CONFIG_VIDEO_VP27SMPX) += vp27smpx.o
 obj-$(CONFIG_VIDEO_SONY_BTF_MPX) += sony-btf-mpx.o
 obj-$(CONFIG_VIDEO_UPD64031A) += upd64031a.o
 obj-$(CONFIG_VIDEO_UPD64083) += upd64083.o
+obj-$(CONFIG_VIDEO_OV5640) += ov5640.o
 obj-$(CONFIG_VIDEO_OV7640) += ov7640.o
 obj-$(CONFIG_VIDEO_OV7670) += ov7670.o
 obj-$(CONFIG_VIDEO_OV9650) += ov9650.o
diff --git a/drivers/media/i2c/ov5640.c b/drivers/media/i2c/ov5640.c
new file mode 100644
index 0000000..2d78ec8
--- /dev/null
+++ b/drivers/media/i2c/ov5640.c
@@ -0,0 +1,2231 @@
+/*
+ * Copyright (C) 2011-2013 Freescale Semiconductor, Inc. All Rights Reserved.
+ * Copyright (C) 2014-2017 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/clkdev.h>
+#include <linux/ctype.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/gpio/consumer.h>
+#include <linux/regulator/consumer.h>
+#include <media/v4l2-async.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-of.h>
+#include <media/v4l2-subdev.h>
+
+/* min/typical/max system clock (xclk) frequencies */
+#define OV5640_XCLK_MIN  6000000
+#define OV5640_XCLK_MAX 24000000
+
+/*
+ * FIXME: there is no subdev API to set the MIPI CSI-2
+ * virtual channel yet, so this is hardcoded for now.
+ */
+#define OV5640_MIPI_VC	1
+
+#define OV5640_DEFAULT_SLAVE_ID 0x3c
+
+#define OV5640_REG_CHIP_ID		0x300a
+#define OV5640_REG_PAD_OUTPUT00		0x3019
+#define OV5640_REG_SC_PLL_CTRL0		0x3034
+#define OV5640_REG_SC_PLL_CTRL1		0x3035
+#define OV5640_REG_SC_PLL_CTRL2		0x3036
+#define OV5640_REG_SC_PLL_CTRL3		0x3037
+#define OV5640_REG_SLAVE_ID		0x3100
+#define OV5640_REG_SYS_ROOT_DIVIDER	0x3108
+#define OV5640_REG_AWB_R_GAIN		0x3400
+#define OV5640_REG_AWB_G_GAIN		0x3402
+#define OV5640_REG_AWB_B_GAIN		0x3404
+#define OV5640_REG_AWB_MANUAL_CTRL	0x3406
+#define OV5640_REG_AEC_PK_EXPOSURE_HI	0x3500
+#define OV5640_REG_AEC_PK_EXPOSURE_MED	0x3501
+#define OV5640_REG_AEC_PK_EXPOSURE_LO	0x3502
+#define OV5640_REG_AEC_PK_MANUAL	0x3503
+#define OV5640_REG_AEC_PK_REAL_GAIN	0x350a
+#define OV5640_REG_AEC_PK_VTS		0x350c
+#define OV5640_REG_TIMING_HTS		0x380c
+#define OV5640_REG_TIMING_VTS		0x380e
+#define OV5640_REG_TIMING_TC_REG21	0x3821
+#define OV5640_REG_AEC_CTRL00		0x3a00
+#define OV5640_REG_AEC_B50_STEP		0x3a08
+#define OV5640_REG_AEC_B60_STEP		0x3a0a
+#define OV5640_REG_AEC_CTRL0D		0x3a0d
+#define OV5640_REG_AEC_CTRL0E		0x3a0e
+#define OV5640_REG_AEC_CTRL0F		0x3a0f
+#define OV5640_REG_AEC_CTRL10		0x3a10
+#define OV5640_REG_AEC_CTRL11		0x3a11
+#define OV5640_REG_AEC_CTRL1B		0x3a1b
+#define OV5640_REG_AEC_CTRL1E		0x3a1e
+#define OV5640_REG_AEC_CTRL1F		0x3a1f
+#define OV5640_REG_HZ5060_CTRL00	0x3c00
+#define OV5640_REG_HZ5060_CTRL01	0x3c01
+#define OV5640_REG_SIGMADELTA_CTRL0C	0x3c0c
+#define OV5640_REG_FRAME_CTRL01		0x4202
+#define OV5640_REG_MIPI_CTRL00		0x4800
+#define OV5640_REG_DEBUG_MODE		0x4814
+#define OV5640_REG_PRE_ISP_TEST_SET1	0x503d
+#define OV5640_REG_SDE_CTRL0		0x5580
+#define OV5640_REG_SDE_CTRL1		0x5581
+#define OV5640_REG_SDE_CTRL3		0x5583
+#define OV5640_REG_SDE_CTRL4		0x5584
+#define OV5640_REG_SDE_CTRL5		0x5585
+#define OV5640_REG_AVG_READOUT		0x56a1
+
+enum ov5640_mode_id {
+	OV5640_MODE_QCIF_176_144 = 0,
+	OV5640_MODE_QVGA_320_240,
+	OV5640_MODE_VGA_640_480,
+	OV5640_MODE_NTSC_720_480,
+	OV5640_MODE_PAL_720_576,
+	OV5640_MODE_XGA_1024_768,
+	OV5640_MODE_720P_1280_720,
+	OV5640_MODE_1080P_1920_1080,
+	OV5640_MODE_QSXGA_2592_1944,
+	OV5640_NUM_MODES,
+};
+
+enum ov5640_frame_rate {
+	OV5640_15_FPS = 0,
+	OV5640_30_FPS,
+	OV5640_NUM_FRAMERATES,
+};
+
+static const int ov5640_framerates[] = {
+	[OV5640_15_FPS] = 15,
+	[OV5640_30_FPS] = 30,
+};
+
+/* regulator supplies */
+static const char * const ov5640_supply_name[] = {
+	"DOVDD", /* Digital I/O (1.8V) suppply */
+	"DVDD",  /* Digital Core (1.5V) supply */
+	"AVDD",  /* Analog (2.8V) supply */
+};
+
+#define OV5640_NUM_SUPPLIES ARRAY_SIZE(ov5640_supply_name)
+
+/*
+ * image size under 1280 * 960 are SUBSAMPLING
+ * image size upper 1280 * 960 are SCALING
+ */
+enum ov5640_downsize_mode {
+	SUBSAMPLING,
+	SCALING,
+};
+
+struct reg_value {
+	u16 reg_addr;
+	u8 val;
+	u8 mask;
+	u32 delay_ms;
+};
+
+struct ov5640_mode_info {
+	enum ov5640_mode_id id;
+	enum ov5640_downsize_mode dn_mode;
+	u32 width;
+	u32 height;
+	const struct reg_value *reg_data;
+	u32 reg_data_size;
+};
+
+struct ov5640_ctrls {
+	struct v4l2_ctrl_handler handler;
+	struct {
+		struct v4l2_ctrl *auto_exp;
+		struct v4l2_ctrl *exposure;
+	};
+	struct {
+		struct v4l2_ctrl *auto_wb;
+		struct v4l2_ctrl *blue_balance;
+		struct v4l2_ctrl *red_balance;
+	};
+	struct {
+		struct v4l2_ctrl *auto_gain;
+		struct v4l2_ctrl *gain;
+	};
+	struct v4l2_ctrl *brightness;
+	struct v4l2_ctrl *saturation;
+	struct v4l2_ctrl *contrast;
+	struct v4l2_ctrl *hue;
+	struct v4l2_ctrl *test_pattern;
+};
+
+struct ov5640_dev {
+	struct i2c_client *i2c_client;
+	struct v4l2_subdev sd;
+	struct media_pad pad;
+	struct v4l2_of_endpoint ep; /* the parsed DT endpoint info */
+	struct clk *xclk; /* system clock to OV5640 */
+	u32 xclk_freq;
+
+	struct regulator_bulk_data supplies[OV5640_NUM_SUPPLIES];
+	struct gpio_desc *reset_gpio;
+	struct gpio_desc *pwdn_gpio;
+
+	/* lock to protect all members below */
+	struct mutex lock;
+
+	int power_count;
+
+	struct v4l2_mbus_framefmt fmt;
+	struct v4l2_captureparm streamcap;
+
+	const struct ov5640_mode_info *current_mode;
+	enum ov5640_frame_rate current_fr;
+
+	struct ov5640_ctrls ctrls;
+
+	u32 prev_sysclk, prev_hts;
+	u32 ae_low, ae_high, ae_target;
+
+	bool pending_mode_change;
+	bool streaming;
+};
+
+static inline struct ov5640_dev *to_ov5640_dev(struct v4l2_subdev *sd)
+{
+	return container_of(sd, struct ov5640_dev, sd);
+}
+
+static inline struct v4l2_subdev *ctrl_to_sd(struct v4l2_ctrl *ctrl)
+{
+	return &container_of(ctrl->handler, struct ov5640_dev,
+			     ctrls.handler)->sd;
+}
+
+/*
+ * FIXME: all of these register tables are likely filled with
+ * entries that set the register to their power-on default values,
+ * and which are otherwise not touched by this driver. Those entries
+ * should be identified and removed to speed register load time
+ * over i2c.
+ */
+
+static const struct reg_value ov5640_init_setting_30fps_VGA[] = {
+
+	{0x3103, 0x11, 0, 0}, {0x3008, 0x82, 0, 5}, {0x3008, 0x42, 0, 0},
+	{0x3103, 0x03, 0, 0}, {0x3017, 0x00, 0, 0}, {0x3018, 0x00, 0, 0},
+	{0x3034, 0x18, 0, 0}, {0x3035, 0x14, 0, 0}, {0x3036, 0x38, 0, 0},
+	{0x3037, 0x13, 0, 0}, {0x3108, 0x01, 0, 0}, {0x3630, 0x36, 0, 0},
+	{0x3631, 0x0e, 0, 0}, {0x3632, 0xe2, 0, 0}, {0x3633, 0x12, 0, 0},
+	{0x3621, 0xe0, 0, 0}, {0x3704, 0xa0, 0, 0}, {0x3703, 0x5a, 0, 0},
+	{0x3715, 0x78, 0, 0}, {0x3717, 0x01, 0, 0}, {0x370b, 0x60, 0, 0},
+	{0x3705, 0x1a, 0, 0}, {0x3905, 0x02, 0, 0}, {0x3906, 0x10, 0, 0},
+	{0x3901, 0x0a, 0, 0}, {0x3731, 0x12, 0, 0}, {0x3600, 0x08, 0, 0},
+	{0x3601, 0x33, 0, 0}, {0x302d, 0x60, 0, 0}, {0x3620, 0x52, 0, 0},
+	{0x371b, 0x20, 0, 0}, {0x471c, 0x50, 0, 0}, {0x3a13, 0x43, 0, 0},
+	{0x3a18, 0x00, 0, 0}, {0x3a19, 0xf8, 0, 0}, {0x3635, 0x13, 0, 0},
+	{0x3636, 0x03, 0, 0}, {0x3634, 0x40, 0, 0}, {0x3622, 0x01, 0, 0},
+	{0x3c01, 0xa4, 0, 0}, {0x3c04, 0x28, 0, 0}, {0x3c05, 0x98, 0, 0},
+	{0x3c06, 0x00, 0, 0}, {0x3c07, 0x08, 0, 0}, {0x3c08, 0x00, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0x80, 0, 0}, {0x380a, 0x01, 0, 0},
+	{0x380b, 0xe0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x3000, 0x00, 0, 0},
+	{0x3002, 0x1c, 0, 0}, {0x3004, 0xff, 0, 0}, {0x3006, 0xc3, 0, 0},
+	{0x300e, 0x45, 0, 0}, {0x302e, 0x08, 0, 0}, {0x4300, 0x3f, 0, 0},
+	{0x501f, 0x00, 0, 0}, {0x4713, 0x03, 0, 0}, {0x4407, 0x04, 0, 0},
+	{0x440e, 0x00, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x4837, 0x0a, 0, 0}, {0x4800, 0x04, 0, 0}, {0x3824, 0x02, 0, 0},
+	{0x5000, 0xa7, 0, 0}, {0x5001, 0xa3, 0, 0}, {0x5180, 0xff, 0, 0},
+	{0x5181, 0xf2, 0, 0}, {0x5182, 0x00, 0, 0}, {0x5183, 0x14, 0, 0},
+	{0x5184, 0x25, 0, 0}, {0x5185, 0x24, 0, 0}, {0x5186, 0x09, 0, 0},
+	{0x5187, 0x09, 0, 0}, {0x5188, 0x09, 0, 0}, {0x5189, 0x88, 0, 0},
+	{0x518a, 0x54, 0, 0}, {0x518b, 0xee, 0, 0}, {0x518c, 0xb2, 0, 0},
+	{0x518d, 0x50, 0, 0}, {0x518e, 0x34, 0, 0}, {0x518f, 0x6b, 0, 0},
+	{0x5190, 0x46, 0, 0}, {0x5191, 0xf8, 0, 0}, {0x5192, 0x04, 0, 0},
+	{0x5193, 0x70, 0, 0}, {0x5194, 0xf0, 0, 0}, {0x5195, 0xf0, 0, 0},
+	{0x5196, 0x03, 0, 0}, {0x5197, 0x01, 0, 0}, {0x5198, 0x04, 0, 0},
+	{0x5199, 0x6c, 0, 0}, {0x519a, 0x04, 0, 0}, {0x519b, 0x00, 0, 0},
+	{0x519c, 0x09, 0, 0}, {0x519d, 0x2b, 0, 0}, {0x519e, 0x38, 0, 0},
+	{0x5381, 0x1e, 0, 0}, {0x5382, 0x5b, 0, 0}, {0x5383, 0x08, 0, 0},
+	{0x5384, 0x0a, 0, 0}, {0x5385, 0x7e, 0, 0}, {0x5386, 0x88, 0, 0},
+	{0x5387, 0x7c, 0, 0}, {0x5388, 0x6c, 0, 0}, {0x5389, 0x10, 0, 0},
+	{0x538a, 0x01, 0, 0}, {0x538b, 0x98, 0, 0}, {0x5300, 0x08, 0, 0},
+	{0x5301, 0x30, 0, 0}, {0x5302, 0x10, 0, 0}, {0x5303, 0x00, 0, 0},
+	{0x5304, 0x08, 0, 0}, {0x5305, 0x30, 0, 0}, {0x5306, 0x08, 0, 0},
+	{0x5307, 0x16, 0, 0}, {0x5309, 0x08, 0, 0}, {0x530a, 0x30, 0, 0},
+	{0x530b, 0x04, 0, 0}, {0x530c, 0x06, 0, 0}, {0x5480, 0x01, 0, 0},
+	{0x5481, 0x08, 0, 0}, {0x5482, 0x14, 0, 0}, {0x5483, 0x28, 0, 0},
+	{0x5484, 0x51, 0, 0}, {0x5485, 0x65, 0, 0}, {0x5486, 0x71, 0, 0},
+	{0x5487, 0x7d, 0, 0}, {0x5488, 0x87, 0, 0}, {0x5489, 0x91, 0, 0},
+	{0x548a, 0x9a, 0, 0}, {0x548b, 0xaa, 0, 0}, {0x548c, 0xb8, 0, 0},
+	{0x548d, 0xcd, 0, 0}, {0x548e, 0xdd, 0, 0}, {0x548f, 0xea, 0, 0},
+	{0x5490, 0x1d, 0, 0}, {0x5580, 0x02, 0, 0}, {0x5583, 0x40, 0, 0},
+	{0x5584, 0x10, 0, 0}, {0x5589, 0x10, 0, 0}, {0x558a, 0x00, 0, 0},
+	{0x558b, 0xf8, 0, 0}, {0x5800, 0x23, 0, 0}, {0x5801, 0x14, 0, 0},
+	{0x5802, 0x0f, 0, 0}, {0x5803, 0x0f, 0, 0}, {0x5804, 0x12, 0, 0},
+	{0x5805, 0x26, 0, 0}, {0x5806, 0x0c, 0, 0}, {0x5807, 0x08, 0, 0},
+	{0x5808, 0x05, 0, 0}, {0x5809, 0x05, 0, 0}, {0x580a, 0x08, 0, 0},
+	{0x580b, 0x0d, 0, 0}, {0x580c, 0x08, 0, 0}, {0x580d, 0x03, 0, 0},
+	{0x580e, 0x00, 0, 0}, {0x580f, 0x00, 0, 0}, {0x5810, 0x03, 0, 0},
+	{0x5811, 0x09, 0, 0}, {0x5812, 0x07, 0, 0}, {0x5813, 0x03, 0, 0},
+	{0x5814, 0x00, 0, 0}, {0x5815, 0x01, 0, 0}, {0x5816, 0x03, 0, 0},
+	{0x5817, 0x08, 0, 0}, {0x5818, 0x0d, 0, 0}, {0x5819, 0x08, 0, 0},
+	{0x581a, 0x05, 0, 0}, {0x581b, 0x06, 0, 0}, {0x581c, 0x08, 0, 0},
+	{0x581d, 0x0e, 0, 0}, {0x581e, 0x29, 0, 0}, {0x581f, 0x17, 0, 0},
+	{0x5820, 0x11, 0, 0}, {0x5821, 0x11, 0, 0}, {0x5822, 0x15, 0, 0},
+	{0x5823, 0x28, 0, 0}, {0x5824, 0x46, 0, 0}, {0x5825, 0x26, 0, 0},
+	{0x5826, 0x08, 0, 0}, {0x5827, 0x26, 0, 0}, {0x5828, 0x64, 0, 0},
+	{0x5829, 0x26, 0, 0}, {0x582a, 0x24, 0, 0}, {0x582b, 0x22, 0, 0},
+	{0x582c, 0x24, 0, 0}, {0x582d, 0x24, 0, 0}, {0x582e, 0x06, 0, 0},
+	{0x582f, 0x22, 0, 0}, {0x5830, 0x40, 0, 0}, {0x5831, 0x42, 0, 0},
+	{0x5832, 0x24, 0, 0}, {0x5833, 0x26, 0, 0}, {0x5834, 0x24, 0, 0},
+	{0x5835, 0x22, 0, 0}, {0x5836, 0x22, 0, 0}, {0x5837, 0x26, 0, 0},
+	{0x5838, 0x44, 0, 0}, {0x5839, 0x24, 0, 0}, {0x583a, 0x26, 0, 0},
+	{0x583b, 0x28, 0, 0}, {0x583c, 0x42, 0, 0}, {0x583d, 0xce, 0, 0},
+	{0x5025, 0x00, 0, 0}, {0x3a0f, 0x30, 0, 0}, {0x3a10, 0x28, 0, 0},
+	{0x3a1b, 0x30, 0, 0}, {0x3a1e, 0x26, 0, 0}, {0x3a11, 0x60, 0, 0},
+	{0x3a1f, 0x14, 0, 0}, {0x3008, 0x02, 0, 0}, {0x3c00, 0x04, 0, 300},
+};
+
+static const struct reg_value ov5640_setting_30fps_VGA_640_480[] = {
+
+	{0x3035, 0x14, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0x80, 0, 0}, {0x380a, 0x01, 0, 0},
+	{0x380b, 0xe0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x04, 0, 0}, {0x380f, 0x38, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x0e, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0}, {0x3503, 0x00, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_VGA_640_480[] = {
+	{0x3035, 0x22, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0x80, 0, 0}, {0x380a, 0x01, 0, 0},
+	{0x380b, 0xe0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_30fps_XGA_1024_768[] = {
+
+	{0x3035, 0x14, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0x80, 0, 0}, {0x380a, 0x01, 0, 0},
+	{0x380b, 0xe0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x04, 0, 0}, {0x380f, 0x38, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x0e, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0}, {0x3503, 0x00, 0, 0},
+	{0x3808, 0x04, 0, 0}, {0x3809, 0x00, 0, 0}, {0x380a, 0x03, 0, 0},
+	{0x380b, 0x00, 0, 0}, {0x3035, 0x12, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_XGA_1024_768[] = {
+	{0x3035, 0x22, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0x80, 0, 0}, {0x380a, 0x01, 0, 0},
+	{0x380b, 0xe0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0}, {0x3808, 0x04, 0, 0},
+	{0x3809, 0x00, 0, 0}, {0x380a, 0x03, 0, 0}, {0x380b, 0x00, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_30fps_QVGA_320_240[] = {
+	{0x3035, 0x14, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x01, 0, 0}, {0x3809, 0x40, 0, 0}, {0x380a, 0x00, 0, 0},
+	{0x380b, 0xf0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_QVGA_320_240[] = {
+	{0x3035, 0x22, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x01, 0, 0}, {0x3809, 0x40, 0, 0}, {0x380a, 0x00, 0, 0},
+	{0x380b, 0xf0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_30fps_QCIF_176_144[] = {
+	{0x3035, 0x14, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x00, 0, 0}, {0x3809, 0xb0, 0, 0}, {0x380a, 0x00, 0, 0},
+	{0x380b, 0x90, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+static const struct reg_value ov5640_setting_15fps_QCIF_176_144[] = {
+	{0x3035, 0x22, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x00, 0, 0}, {0x3809, 0xb0, 0, 0}, {0x380a, 0x00, 0, 0},
+	{0x380b, 0x90, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_30fps_NTSC_720_480[] = {
+	{0x3035, 0x12, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0xd0, 0, 0}, {0x380a, 0x01, 0, 0},
+	{0x380b, 0xe0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x3c, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_NTSC_720_480[] = {
+	{0x3035, 0x22, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0xd0, 0, 0}, {0x380a, 0x01, 0, 0},
+	{0x380b, 0xe0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x3c, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_30fps_PAL_720_576[] = {
+	{0x3035, 0x12, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0xd0, 0, 0}, {0x380a, 0x02, 0, 0},
+	{0x380b, 0x40, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x38, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_PAL_720_576[] = {
+	{0x3035, 0x22, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0xd0, 0, 0}, {0x380a, 0x02, 0, 0},
+	{0x380b, 0x40, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x38, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_30fps_720P_1280_720[] = {
+	{0x3008, 0x42, 0, 0},
+	{0x3035, 0x21, 0, 0}, {0x3036, 0x54, 0, 0}, {0x3c07, 0x07, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0xfa, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x06, 0, 0}, {0x3807, 0xa9, 0, 0},
+	{0x3808, 0x05, 0, 0}, {0x3809, 0x00, 0, 0}, {0x380a, 0x02, 0, 0},
+	{0x380b, 0xd0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x64, 0, 0},
+	{0x380e, 0x02, 0, 0}, {0x380f, 0xe4, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x04, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x02, 0, 0},
+	{0x3a03, 0xe4, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0xbc, 0, 0},
+	{0x3a0a, 0x01, 0, 0}, {0x3a0b, 0x72, 0, 0}, {0x3a0e, 0x01, 0, 0},
+	{0x3a0d, 0x02, 0, 0}, {0x3a14, 0x02, 0, 0}, {0x3a15, 0xe4, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x02, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x37, 0, 0}, {0x460c, 0x20, 0, 0},
+	{0x3824, 0x04, 0, 0}, {0x5001, 0x83, 0, 0}, {0x4005, 0x1a, 0, 0},
+	{0x3008, 0x02, 0, 0}, {0x3503, 0,    0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_720P_1280_720[] = {
+	{0x3035, 0x41, 0, 0}, {0x3036, 0x54, 0, 0}, {0x3c07, 0x07, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0xfa, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x06, 0, 0}, {0x3807, 0xa9, 0, 0},
+	{0x3808, 0x05, 0, 0}, {0x3809, 0x00, 0, 0}, {0x380a, 0x02, 0, 0},
+	{0x380b, 0xd0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x64, 0, 0},
+	{0x380e, 0x02, 0, 0}, {0x380f, 0xe4, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x04, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x02, 0, 0},
+	{0x3a03, 0xe4, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0xbc, 0, 0},
+	{0x3a0a, 0x01, 0, 0}, {0x3a0b, 0x72, 0, 0}, {0x3a0e, 0x01, 0, 0},
+	{0x3a0d, 0x02, 0, 0}, {0x3a14, 0x02, 0, 0}, {0x3a15, 0xe4, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x02, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x37, 0, 0}, {0x460c, 0x20, 0, 0},
+	{0x3824, 0x04, 0, 0}, {0x5001, 0x83, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_30fps_1080P_1920_1080[] = {
+	{0x3008, 0x42, 0, 0},
+	{0x3035, 0x21, 0, 0}, {0x3036, 0x54, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x40, 0, 0}, {0x3821, 0x06, 0, 0}, {0x3814, 0x11, 0, 0},
+	{0x3815, 0x11, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x00, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9f, 0, 0},
+	{0x3808, 0x0a, 0, 0}, {0x3809, 0x20, 0, 0}, {0x380a, 0x07, 0, 0},
+	{0x380b, 0x98, 0, 0}, {0x380c, 0x0b, 0, 0}, {0x380d, 0x1c, 0, 0},
+	{0x380e, 0x07, 0, 0}, {0x380f, 0xb0, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x04, 0, 0},
+	{0x3618, 0x04, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x21, 0, 0},
+	{0x3709, 0x12, 0, 0}, {0x370c, 0x00, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x06, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0x83, 0, 0}, {0x3035, 0x11, 0, 0},
+	{0x3036, 0x54, 0, 0}, {0x3c07, 0x07, 0, 0}, {0x3c08, 0x00, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3800, 0x01, 0, 0}, {0x3801, 0x50, 0, 0}, {0x3802, 0x01, 0, 0},
+	{0x3803, 0xb2, 0, 0}, {0x3804, 0x08, 0, 0}, {0x3805, 0xef, 0, 0},
+	{0x3806, 0x05, 0, 0}, {0x3807, 0xf1, 0, 0}, {0x3808, 0x07, 0, 0},
+	{0x3809, 0x80, 0, 0}, {0x380a, 0x04, 0, 0}, {0x380b, 0x38, 0, 0},
+	{0x380c, 0x09, 0, 0}, {0x380d, 0xc4, 0, 0}, {0x380e, 0x04, 0, 0},
+	{0x380f, 0x60, 0, 0}, {0x3612, 0x2b, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3a02, 0x04, 0, 0}, {0x3a03, 0x60, 0, 0}, {0x3a08, 0x01, 0, 0},
+	{0x3a09, 0x50, 0, 0}, {0x3a0a, 0x01, 0, 0}, {0x3a0b, 0x18, 0, 0},
+	{0x3a0e, 0x03, 0, 0}, {0x3a0d, 0x04, 0, 0}, {0x3a14, 0x04, 0, 0},
+	{0x3a15, 0x60, 0, 0}, {0x4713, 0x02, 0, 0}, {0x4407, 0x04, 0, 0},
+	{0x460b, 0x37, 0, 0}, {0x460c, 0x20, 0, 0}, {0x3824, 0x04, 0, 0},
+	{0x4005, 0x1a, 0, 0}, {0x3008, 0x02, 0, 0},
+	{0x3503, 0, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_1080P_1920_1080[] = {
+	{0x3008, 0x42, 0, 0},
+	{0x3035, 0x21, 0, 0}, {0x3036, 0x54, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x40, 0, 0}, {0x3821, 0x06, 0, 0}, {0x3814, 0x11, 0, 0},
+	{0x3815, 0x11, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x00, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9f, 0, 0},
+	{0x3808, 0x0a, 0, 0}, {0x3809, 0x20, 0, 0}, {0x380a, 0x07, 0, 0},
+	{0x380b, 0x98, 0, 0}, {0x380c, 0x0b, 0, 0}, {0x380d, 0x1c, 0, 0},
+	{0x380e, 0x07, 0, 0}, {0x380f, 0xb0, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x04, 0, 0},
+	{0x3618, 0x04, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x21, 0, 0},
+	{0x3709, 0x12, 0, 0}, {0x370c, 0x00, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x06, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0x83, 0, 0}, {0x3035, 0x21, 0, 0},
+	{0x3036, 0x54, 0, 1}, {0x3c07, 0x07, 0, 0}, {0x3c08, 0x00, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3800, 0x01, 0, 0}, {0x3801, 0x50, 0, 0}, {0x3802, 0x01, 0, 0},
+	{0x3803, 0xb2, 0, 0}, {0x3804, 0x08, 0, 0}, {0x3805, 0xef, 0, 0},
+	{0x3806, 0x05, 0, 0}, {0x3807, 0xf1, 0, 0}, {0x3808, 0x07, 0, 0},
+	{0x3809, 0x80, 0, 0}, {0x380a, 0x04, 0, 0}, {0x380b, 0x38, 0, 0},
+	{0x380c, 0x09, 0, 0}, {0x380d, 0xc4, 0, 0}, {0x380e, 0x04, 0, 0},
+	{0x380f, 0x60, 0, 0}, {0x3612, 0x2b, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3a02, 0x04, 0, 0}, {0x3a03, 0x60, 0, 0}, {0x3a08, 0x01, 0, 0},
+	{0x3a09, 0x50, 0, 0}, {0x3a0a, 0x01, 0, 0}, {0x3a0b, 0x18, 0, 0},
+	{0x3a0e, 0x03, 0, 0}, {0x3a0d, 0x04, 0, 0}, {0x3a14, 0x04, 0, 0},
+	{0x3a15, 0x60, 0, 0}, {0x4713, 0x02, 0, 0}, {0x4407, 0x04, 0, 0},
+	{0x460b, 0x37, 0, 0}, {0x460c, 0x20, 0, 0}, {0x3824, 0x04, 0, 0},
+	{0x4005, 0x1a, 0, 0}, {0x3008, 0x02, 0, 0}, {0x3503, 0, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_QSXGA_2592_1944[] = {
+	{0x3820, 0x40, 0, 0}, {0x3821, 0x06, 0, 0},
+	{0x3035, 0x21, 0, 0}, {0x3036, 0x54, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x40, 0, 0}, {0x3821, 0x06, 0, 0}, {0x3814, 0x11, 0, 0},
+	{0x3815, 0x11, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x00, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9f, 0, 0},
+	{0x3808, 0x0a, 0, 0}, {0x3809, 0x20, 0, 0}, {0x380a, 0x07, 0, 0},
+	{0x380b, 0x98, 0, 0}, {0x380c, 0x0b, 0, 0}, {0x380d, 0x1c, 0, 0},
+	{0x380e, 0x07, 0, 0}, {0x380f, 0xb0, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x04, 0, 0},
+	{0x3618, 0x04, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x21, 0, 0},
+	{0x3709, 0x12, 0, 0}, {0x370c, 0x00, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x06, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0x83, 0, 70},
+};
+
+/* power-on sensor init reg table */
+static const struct ov5640_mode_info ov5640_mode_init_data = {
+	0, SUBSAMPLING, 640, 480, ov5640_init_setting_30fps_VGA,
+	ARRAY_SIZE(ov5640_init_setting_30fps_VGA),
+};
+
+static const struct ov5640_mode_info
+ov5640_mode_data[OV5640_NUM_FRAMERATES][OV5640_NUM_MODES] = {
+	{
+		{OV5640_MODE_QCIF_176_144, SUBSAMPLING, 176, 144,
+		 ov5640_setting_15fps_QCIF_176_144,
+		 ARRAY_SIZE(ov5640_setting_15fps_QCIF_176_144)},
+		{OV5640_MODE_QVGA_320_240, SUBSAMPLING, 320,  240,
+		 ov5640_setting_15fps_QVGA_320_240,
+		 ARRAY_SIZE(ov5640_setting_15fps_QVGA_320_240)},
+		{OV5640_MODE_VGA_640_480, SUBSAMPLING, 640,  480,
+		 ov5640_setting_15fps_VGA_640_480,
+		 ARRAY_SIZE(ov5640_setting_15fps_VGA_640_480)},
+		{OV5640_MODE_NTSC_720_480, SUBSAMPLING, 720, 480,
+		 ov5640_setting_15fps_NTSC_720_480,
+		 ARRAY_SIZE(ov5640_setting_15fps_NTSC_720_480)},
+		{OV5640_MODE_PAL_720_576, SUBSAMPLING, 720, 576,
+		 ov5640_setting_15fps_PAL_720_576,
+		 ARRAY_SIZE(ov5640_setting_15fps_PAL_720_576)},
+		{OV5640_MODE_XGA_1024_768, SUBSAMPLING, 1024, 768,
+		 ov5640_setting_15fps_XGA_1024_768,
+		 ARRAY_SIZE(ov5640_setting_15fps_XGA_1024_768)},
+		{OV5640_MODE_720P_1280_720, SUBSAMPLING, 1280, 720,
+		 ov5640_setting_15fps_720P_1280_720,
+		 ARRAY_SIZE(ov5640_setting_15fps_720P_1280_720)},
+		{OV5640_MODE_1080P_1920_1080, SCALING, 1920, 1080,
+		 ov5640_setting_15fps_1080P_1920_1080,
+		 ARRAY_SIZE(ov5640_setting_15fps_1080P_1920_1080)},
+		{OV5640_MODE_QSXGA_2592_1944, SCALING, 2592, 1944,
+		 ov5640_setting_15fps_QSXGA_2592_1944,
+		 ARRAY_SIZE(ov5640_setting_15fps_QSXGA_2592_1944)},
+	}, {
+		{OV5640_MODE_QCIF_176_144, SUBSAMPLING, 176, 144,
+		 ov5640_setting_30fps_QCIF_176_144,
+		 ARRAY_SIZE(ov5640_setting_30fps_QCIF_176_144)},
+		{OV5640_MODE_QVGA_320_240, SUBSAMPLING, 320,  240,
+		 ov5640_setting_30fps_QVGA_320_240,
+		 ARRAY_SIZE(ov5640_setting_30fps_QVGA_320_240)},
+		{OV5640_MODE_VGA_640_480, SUBSAMPLING, 640,  480,
+		 ov5640_setting_30fps_VGA_640_480,
+		 ARRAY_SIZE(ov5640_setting_30fps_VGA_640_480)},
+		{OV5640_MODE_NTSC_720_480, SUBSAMPLING, 720, 480,
+		 ov5640_setting_30fps_NTSC_720_480,
+		 ARRAY_SIZE(ov5640_setting_30fps_NTSC_720_480)},
+		{OV5640_MODE_PAL_720_576, SUBSAMPLING, 720, 576,
+		 ov5640_setting_30fps_PAL_720_576,
+		 ARRAY_SIZE(ov5640_setting_30fps_PAL_720_576)},
+		{OV5640_MODE_XGA_1024_768, SUBSAMPLING, 1024, 768,
+		 ov5640_setting_30fps_XGA_1024_768,
+		 ARRAY_SIZE(ov5640_setting_30fps_XGA_1024_768)},
+		{OV5640_MODE_720P_1280_720, SUBSAMPLING, 1280, 720,
+		 ov5640_setting_30fps_720P_1280_720,
+		 ARRAY_SIZE(ov5640_setting_30fps_720P_1280_720)},
+		{OV5640_MODE_1080P_1920_1080, SCALING, 1920, 1080,
+		 ov5640_setting_30fps_1080P_1920_1080,
+		 ARRAY_SIZE(ov5640_setting_30fps_1080P_1920_1080)},
+		{OV5640_MODE_QSXGA_2592_1944, -1, 0, 0, NULL, 0},
+	},
+};
+
+static int ov5640_init_slave_id(struct ov5640_dev *sensor)
+{
+	struct i2c_client *client = sensor->i2c_client;
+	struct i2c_msg msg;
+	u8 buf[3];
+	int ret;
+
+	if (client->addr == OV5640_DEFAULT_SLAVE_ID)
+		return 0;
+
+	buf[0] = OV5640_REG_SLAVE_ID >> 8;
+	buf[1] = OV5640_REG_SLAVE_ID & 0xff;
+	buf[2] = client->addr << 1;
+
+	msg.addr = OV5640_DEFAULT_SLAVE_ID;
+	msg.flags = 0;
+	msg.buf = buf;
+	msg.len = sizeof(buf);
+
+	ret = i2c_transfer(client->adapter, &msg, 1);
+	if (ret < 0) {
+		dev_err(&client->dev, "%s: failed with %d\n", __func__, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int ov5640_write_reg(struct ov5640_dev *sensor, u16 reg, u8 val)
+{
+	struct i2c_client *client = sensor->i2c_client;
+	struct i2c_msg msg;
+	u8 buf[3];
+	int ret;
+
+	buf[0] = reg >> 8;
+	buf[1] = reg & 0xff;
+	buf[2] = val;
+
+	msg.addr = client->addr;
+	msg.flags = client->flags;
+	msg.buf = buf;
+	msg.len = sizeof(buf);
+
+	ret = i2c_transfer(client->adapter, &msg, 1);
+	if (ret < 0) {
+		v4l2_err(&sensor->sd, "%s: error: reg=%x, val=%x\n",
+			__func__, reg, val);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int ov5640_read_reg(struct ov5640_dev *sensor, u16 reg, u8 *val)
+{
+	struct i2c_client *client = sensor->i2c_client;
+	struct i2c_msg msg[2];
+	u8 buf[2];
+	int ret;
+
+	buf[0] = reg >> 8;
+	buf[1] = reg & 0xff;
+
+	msg[0].addr = client->addr;
+	msg[0].flags = client->flags;
+	msg[0].buf = buf;
+	msg[0].len = sizeof(buf);
+
+	msg[1].addr = client->addr;
+	msg[1].flags = client->flags | I2C_M_RD;
+	msg[1].buf = buf;
+	msg[1].len = 1;
+
+	ret = i2c_transfer(client->adapter, msg, 2);
+	if (ret < 0)
+		return ret;
+
+	*val = buf[0];
+	return 0;
+}
+
+static int ov5640_read_reg16(struct ov5640_dev *sensor, u16 reg, u16 *val)
+{
+	u8 hi, lo;
+
+	ov5640_read_reg(sensor, reg, &hi);
+	ov5640_read_reg(sensor, reg+1, &lo);
+
+	*val = ((u16)hi << 8) | (u16)lo;
+	return 0;
+}
+
+static int ov5640_write_reg16(struct ov5640_dev *sensor, u16 reg, u16 val)
+{
+	ov5640_write_reg(sensor, reg, val >> 8);
+	ov5640_write_reg(sensor, reg + 1, val & 0xff);
+	return 0;
+}
+
+static int ov5640_mod_reg(struct ov5640_dev *sensor, u16 reg,
+			  u8 mask, u8 val)
+{
+	u8 readval;
+
+	ov5640_read_reg(sensor, reg, &readval);
+
+	readval &= ~mask;
+	val &= mask;
+	val |= readval;
+
+	ov5640_write_reg(sensor, reg, val);
+	return 0;
+}
+
+/* download ov5640 settings to sensor through i2c */
+static int ov5640_load_regs(struct ov5640_dev *sensor,
+			    const struct ov5640_mode_info *mode)
+{
+	const struct reg_value *regs = mode->reg_data;
+	unsigned int i;
+	u32 delay_ms;
+	u16 reg_addr;
+	u8 mask, val;
+
+	for (i = 0; i < mode->reg_data_size; ++i, ++regs) {
+		delay_ms = regs->delay_ms;
+		reg_addr = regs->reg_addr;
+		val = regs->val;
+		mask = regs->mask;
+
+		if (mask)
+			ov5640_mod_reg(sensor, reg_addr, mask, val);
+		else
+			ov5640_write_reg(sensor, reg_addr, val);
+		if (delay_ms)
+			usleep_range(1000*delay_ms, 1000*delay_ms+100);
+	}
+
+	return 0;
+}
+
+static int ov5640_set_hue(struct ov5640_dev *sensor, int value)
+{
+	if (value) {
+		ov5640_mod_reg(sensor, OV5640_REG_SDE_CTRL0, BIT(0), BIT(0));
+		ov5640_write_reg16(sensor, OV5640_REG_SDE_CTRL1, value);
+	} else {
+		ov5640_mod_reg(sensor, OV5640_REG_SDE_CTRL0, BIT(0), 0);
+	}
+
+	return 0;
+}
+
+static int ov5640_set_contrast(struct ov5640_dev *sensor, int value)
+{
+	if (value) {
+		ov5640_mod_reg(sensor, OV5640_REG_SDE_CTRL0, BIT(2), BIT(2));
+		ov5640_write_reg(sensor, OV5640_REG_SDE_CTRL5, value & 0xff);
+	} else {
+		ov5640_mod_reg(sensor, OV5640_REG_SDE_CTRL0, BIT(2), 0);
+	}
+
+	return 0;
+}
+
+static int ov5640_set_saturation(struct ov5640_dev *sensor, int value)
+{
+	if (value) {
+		ov5640_mod_reg(sensor, OV5640_REG_SDE_CTRL0, BIT(1), BIT(1));
+		ov5640_write_reg(sensor, OV5640_REG_SDE_CTRL3, value & 0xff);
+		ov5640_write_reg(sensor, OV5640_REG_SDE_CTRL4, value & 0xff);
+	} else {
+		ov5640_mod_reg(sensor, OV5640_REG_SDE_CTRL0, BIT(1), 0);
+	}
+
+	return 0;
+}
+
+static int ov5640_set_white_balance(struct ov5640_dev *sensor, int awb)
+{
+	ov5640_mod_reg(sensor, OV5640_REG_AWB_MANUAL_CTRL,
+		       BIT(0), awb ? 0 : 1);
+
+	if (!awb) {
+		u16 red = (u16)sensor->ctrls.red_balance->val;
+		u16 blue = (u16)sensor->ctrls.blue_balance->val;
+
+		ov5640_write_reg16(sensor, OV5640_REG_AWB_R_GAIN, red);
+		ov5640_write_reg16(sensor, OV5640_REG_AWB_B_GAIN, blue);
+	}
+
+	return 0;
+}
+
+static int ov5640_set_exposure(struct ov5640_dev *sensor, int exp)
+{
+	struct ov5640_ctrls *ctrls = &sensor->ctrls;
+	bool auto_exposure = (exp == V4L2_EXPOSURE_AUTO);
+
+	if (ctrls->auto_exp->is_new) {
+		ov5640_mod_reg(sensor, OV5640_REG_AEC_PK_MANUAL,
+			       BIT(0), auto_exposure ? 0 : BIT(0));
+	}
+
+	if (!auto_exposure && ctrls->exposure->is_new) {
+		u16 max_exp;
+
+		ov5640_read_reg16(sensor, OV5640_REG_AEC_PK_VTS, &max_exp);
+		if (ctrls->exposure->val < max_exp) {
+			u32 exposure = ctrls->exposure->val << 4;
+
+			ov5640_write_reg(sensor, OV5640_REG_AEC_PK_EXPOSURE_LO,
+					 exposure & 0xff);
+			ov5640_write_reg(sensor, OV5640_REG_AEC_PK_EXPOSURE_MED,
+					 (exposure >> 8) & 0xff);
+			ov5640_write_reg(sensor, OV5640_REG_AEC_PK_EXPOSURE_HI,
+					 (exposure >> 16) & 0x0f);
+		}
+	}
+
+	return 0;
+}
+
+/* read exposure, in number of line periods */
+static int ov5640_get_exposure(struct ov5640_dev *sensor)
+{
+	u8 temp;
+	int exp;
+
+	ov5640_read_reg(sensor, OV5640_REG_AEC_PK_EXPOSURE_HI, &temp);
+	exp = ((int)temp & 0x0f) << 16;
+	ov5640_read_reg(sensor, OV5640_REG_AEC_PK_EXPOSURE_MED, &temp);
+	exp |= ((int)temp << 8);
+	ov5640_read_reg(sensor, OV5640_REG_AEC_PK_EXPOSURE_LO, &temp);
+	exp |= (int)temp;
+
+	return exp >> 4;
+}
+
+static int ov5640_set_gain(struct ov5640_dev *sensor, int auto_gain)
+{
+	struct ov5640_ctrls *ctrls = &sensor->ctrls;
+
+	if (ctrls->auto_gain->is_new) {
+		ov5640_mod_reg(sensor, OV5640_REG_AEC_PK_MANUAL,
+			       BIT(1), ctrls->auto_gain->val ? 0 : BIT(1));
+	}
+
+	if (!auto_gain && ctrls->gain->is_new) {
+		u16 gain = (u16)ctrls->gain->val;
+
+		ov5640_write_reg16(sensor, OV5640_REG_AEC_PK_REAL_GAIN,
+				   gain & 0x3ff);
+	}
+
+	return 0;
+}
+
+static int ov5640_get_gain(struct ov5640_dev *sensor)
+{
+	u16 gain;
+
+	ov5640_read_reg16(sensor, OV5640_REG_AEC_PK_REAL_GAIN, &gain);
+
+	return gain & 0x3ff;
+}
+
+static int ov5640_set_agc_aec(struct ov5640_dev *sensor, bool on)
+{
+	ov5640_mod_reg(sensor, OV5640_REG_AEC_PK_MANUAL,
+		       0x3, on ? 0 : 0x3);
+	return 0;
+}
+
+static int ov5640_set_test_pattern(struct ov5640_dev *sensor, int value)
+{
+	ov5640_mod_reg(sensor, OV5640_REG_PRE_ISP_TEST_SET1,
+		       0xa4, value ? 0xa4 : 0);
+	return 0;
+}
+
+static int ov5640_set_stream(struct ov5640_dev *sensor, bool on)
+{
+	ov5640_mod_reg(sensor, OV5640_REG_MIPI_CTRL00, BIT(5),
+		       on ? 0 : BIT(5));
+	ov5640_write_reg(sensor, OV5640_REG_PAD_OUTPUT00,
+			 on ? 0x00 : 0x70);
+	ov5640_write_reg(sensor, OV5640_REG_FRAME_CTRL01,
+			 on ? 0x00 : 0x0f);
+	return 0;
+}
+
+static int ov5640_get_sysclk(struct ov5640_dev *sensor)
+{
+	 /* calculate sysclk */
+	u32 xvclk = sensor->xclk_freq / 10000;
+	u32 multiplier, prediv, VCO, sysdiv, pll_rdiv;
+	u32 sclk_rdiv_map[] = {1, 2, 4, 8};
+	u32 bit_div2x = 1, sclk_rdiv, sysclk;
+	u8 temp1, temp2;
+
+	ov5640_read_reg(sensor, OV5640_REG_SC_PLL_CTRL0, &temp1);
+	temp2 = temp1 & 0x0f;
+	if (temp2 == 8 || temp2 == 10)
+		bit_div2x = temp2 / 2;
+
+	ov5640_read_reg(sensor, OV5640_REG_SC_PLL_CTRL1, &temp1);
+	sysdiv = temp1 >> 4;
+	if (sysdiv == 0)
+		sysdiv = 16;
+
+	ov5640_read_reg(sensor, OV5640_REG_SC_PLL_CTRL2, &temp1);
+	multiplier = temp1;
+
+	ov5640_read_reg(sensor, OV5640_REG_SC_PLL_CTRL3, &temp1);
+	prediv = temp1 & 0x0f;
+	pll_rdiv = ((temp1 >> 4) & 0x01) + 1;
+
+	ov5640_read_reg(sensor, OV5640_REG_SYS_ROOT_DIVIDER, &temp1);
+	temp2 = temp1 & 0x03;
+	sclk_rdiv = sclk_rdiv_map[temp2];
+
+	VCO = xvclk * multiplier / prediv;
+
+	sysclk = VCO / sysdiv / pll_rdiv * 2 / bit_div2x / sclk_rdiv;
+
+	return sysclk;
+}
+
+static int ov5640_set_night_mode(struct ov5640_dev *sensor)
+{
+	 /* read HTS from register settings */
+	u8 mode;
+
+	ov5640_read_reg(sensor, OV5640_REG_AEC_CTRL00, &mode);
+	mode &= 0xfb;
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL00, mode);
+	return 0;
+}
+
+static int ov5640_get_hts(struct ov5640_dev *sensor)
+{
+	/* read HTS from register settings */
+	u16 hts;
+
+	ov5640_read_reg16(sensor, OV5640_REG_TIMING_HTS, &hts);
+	return hts;
+}
+
+static int ov5640_get_vts(struct ov5640_dev *sensor)
+{
+	u16 vts;
+
+	ov5640_read_reg16(sensor, OV5640_REG_TIMING_VTS, &vts);
+	return vts;
+}
+
+static int ov5640_set_vts(struct ov5640_dev *sensor, int vts)
+{
+	ov5640_write_reg16(sensor, OV5640_REG_TIMING_VTS, vts);
+	return 0;
+}
+
+static int ov5640_get_light_freq(struct ov5640_dev *sensor)
+{
+	/* get banding filter value */
+	u8 temp, temp1;
+	int light_freq = 0;
+
+	ov5640_read_reg(sensor, OV5640_REG_HZ5060_CTRL01, &temp);
+
+	if (temp & 0x80) {
+		/* manual */
+		ov5640_read_reg(sensor, OV5640_REG_HZ5060_CTRL00, &temp1);
+		if (temp1 & 0x04) {
+			/* 50Hz */
+			light_freq = 50;
+		} else {
+			/* 60Hz */
+			light_freq = 60;
+		}
+	} else {
+		/* auto */
+		ov5640_read_reg(sensor, OV5640_REG_SIGMADELTA_CTRL0C,
+				&temp1);
+		if (temp1 & 0x01) {
+			/* 50Hz */
+			light_freq = 50;
+		} else {
+			/* 60Hz */
+		}
+	}
+
+	return light_freq;
+}
+
+static int ov5640_set_bandingfilter(struct ov5640_dev *sensor)
+{
+	u32 band_step60, max_band60, band_step50, max_band50, prev_vts;
+	int ret;
+
+	/* read preview PCLK */
+	ret = ov5640_get_sysclk(sensor);
+	if (ret < 0)
+		return ret;
+	sensor->prev_sysclk = ret;
+	/* read preview HTS */
+	ret = ov5640_get_hts(sensor);
+	if (ret < 0)
+		return ret;
+	sensor->prev_hts = ret;
+
+	/* read preview VTS */
+	ret = ov5640_get_vts(sensor);
+	if (ret < 0)
+		return ret;
+	prev_vts = ret;
+
+	/* calculate banding filter */
+	/* 60Hz */
+	band_step60 = sensor->prev_sysclk * 100 / sensor->prev_hts * 100/120;
+	ov5640_write_reg16(sensor, OV5640_REG_AEC_B60_STEP, band_step60);
+
+	max_band60 = (int)((prev_vts-4)/band_step60);
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL0D, max_band60);
+
+	/* 50Hz */
+	band_step50 = sensor->prev_sysclk * 100 / sensor->prev_hts;
+	ov5640_write_reg16(sensor, OV5640_REG_AEC_B50_STEP, band_step50);
+
+	max_band50 = (int)((prev_vts-4)/band_step50);
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL0E, max_band50);
+
+	return 0;
+}
+
+static int ov5640_set_ae_target(struct ov5640_dev *sensor, int target)
+{
+	/* stable in high */
+	u32 fast_high, fast_low;
+
+	sensor->ae_low = target * 23 / 25;	/* 0.92 */
+	sensor->ae_high = target * 27 / 25;	/* 1.08 */
+
+	fast_high = sensor->ae_high << 1;
+	if (fast_high > 255)
+		fast_high = 255;
+
+	fast_low = sensor->ae_low >> 1;
+
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL0F, sensor->ae_high);
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL10, sensor->ae_low);
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL1B, sensor->ae_high);
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL1E, sensor->ae_low);
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL11, fast_high);
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL1F, fast_low);
+
+	return 0;
+}
+
+static int ov5640_binning_on(struct ov5640_dev *sensor)
+{
+	u8 temp;
+
+	ov5640_read_reg(sensor, OV5640_REG_TIMING_TC_REG21, &temp);
+	temp &= 0xfe;
+
+	return temp ? 1 : 0;
+}
+
+static int ov5640_set_virtual_channel(struct ov5640_dev *sensor)
+{
+	u8 temp, channel = OV5640_MIPI_VC;
+
+	ov5640_read_reg(sensor, OV5640_REG_DEBUG_MODE, &temp);
+	temp &= ~(3 << 6);
+	temp |= (channel << 6);
+	ov5640_write_reg(sensor, OV5640_REG_DEBUG_MODE, temp);
+
+	return 0;
+}
+
+static const struct ov5640_mode_info *
+ov5640_find_mode(struct ov5640_dev *sensor, enum ov5640_frame_rate fr,
+		 int width, int height, bool nearest)
+{
+	const struct ov5640_mode_info *mode = NULL;
+	int i;
+
+	for (i = OV5640_NUM_MODES - 1; i >= 0; i--) {
+		mode = &ov5640_mode_data[fr][i];
+
+		if (!mode->reg_data)
+			continue;
+
+		if ((nearest && mode->width <= width &&
+		     mode->height <= height) ||
+		    (!nearest && mode->width == width &&
+		     mode->height == height))
+			break;
+	}
+
+	if (nearest && i < 0)
+		mode = &ov5640_mode_data[fr][0];
+
+	return mode;
+}
+
+/*
+ * sensor changes between scaling and subsampling, go through
+ * exposure calculation
+ */
+static int ov5640_set_mode_exposure_calc(
+	struct ov5640_dev *sensor, const struct ov5640_mode_info *mode)
+{
+	u32 prev_shutter, prev_gain16;
+	u32 cap_shutter, cap_gain16;
+	u32 cap_sysclk, cap_hts, cap_vts;
+	u32 light_freq, cap_bandfilt, cap_maxband;
+	u32 cap_gain16_shutter;
+	u8 average;
+	int ret;
+
+	if (mode->reg_data == NULL)
+		return -EINVAL;
+
+	/* turn off AE/AG */
+	ret = ov5640_set_agc_aec(sensor, false);
+	if (ret < 0)
+		return ret;
+
+	/* read preview shutter */
+	ret = ov5640_get_exposure(sensor);
+	if (ret < 0)
+		return ret;
+	prev_shutter = ret;
+	ret = ov5640_binning_on(sensor);
+	if (ret < 0)
+		return ret;
+	if (ret && mode->id != OV5640_MODE_720P_1280_720 &&
+	    mode->id != OV5640_MODE_1080P_1920_1080)
+		prev_shutter *= 2;
+
+	/* read preview gain */
+	ret = ov5640_get_gain(sensor);
+	if (ret < 0)
+		return ret;
+	prev_gain16 = ret;
+
+	/* get average */
+	ov5640_read_reg(sensor, OV5640_REG_AVG_READOUT, &average);
+
+	/* turn off night mode for capture */
+	ret = ov5640_set_night_mode(sensor);
+	if (ret < 0)
+		return ret;
+
+	/* Write capture setting */
+	ret = ov5640_load_regs(sensor, mode);
+	if (ret < 0)
+		return ret;
+
+	/* read capture VTS */
+	ret = ov5640_get_vts(sensor);
+	if (ret < 0)
+		return ret;
+	cap_vts = ret;
+	ret = ov5640_get_hts(sensor);
+	if (ret < 0)
+		return ret;
+	cap_hts = ret;
+	ret = ov5640_get_sysclk(sensor);
+	if (ret < 0)
+		return ret;
+	cap_sysclk = ret;
+
+	/* calculate capture banding filter */
+	ret = ov5640_get_light_freq(sensor);
+	if (ret < 0)
+		return ret;
+	light_freq = ret;
+
+	if (light_freq == 60) {
+		/* 60Hz */
+		cap_bandfilt = cap_sysclk * 100 / cap_hts * 100 / 120;
+	} else {
+		/* 50Hz */
+		cap_bandfilt = cap_sysclk * 100 / cap_hts;
+	}
+	cap_maxband = (int)((cap_vts - 4) / cap_bandfilt);
+
+	/* calculate capture shutter/gain16 */
+	if (average > sensor->ae_low && average < sensor->ae_high) {
+		/* in stable range */
+		cap_gain16_shutter =
+			prev_gain16 * prev_shutter *
+			cap_sysclk / sensor->prev_sysclk *
+			sensor->prev_hts / cap_hts *
+			sensor->ae_target / average;
+	} else {
+		cap_gain16_shutter =
+			prev_gain16 * prev_shutter *
+			cap_sysclk / sensor->prev_sysclk *
+			sensor->prev_hts / cap_hts;
+	}
+
+	/* gain to shutter */
+	if (cap_gain16_shutter < (cap_bandfilt * 16)) {
+		/* shutter < 1/100 */
+		cap_shutter = cap_gain16_shutter / 16;
+		if (cap_shutter < 1)
+			cap_shutter = 1;
+
+		cap_gain16 = cap_gain16_shutter / cap_shutter;
+		if (cap_gain16 < 16)
+			cap_gain16 = 16;
+	} else {
+		if (cap_gain16_shutter > (cap_bandfilt * cap_maxband * 16)) {
+			/* exposure reach max */
+			cap_shutter = cap_bandfilt * cap_maxband;
+			cap_gain16 = cap_gain16_shutter / cap_shutter;
+		} else {
+			/* 1/100 < (cap_shutter = n/100) =< max */
+			cap_shutter =
+				((int)(cap_gain16_shutter / 16 / cap_bandfilt))
+				* cap_bandfilt;
+			cap_gain16 = cap_gain16_shutter / cap_shutter;
+		}
+	}
+
+	/* write capture gain */
+	ret = ov5640_set_gain(sensor, cap_gain16);
+	if (ret < 0)
+		return ret;
+
+	/* write capture shutter */
+	if (cap_shutter > (cap_vts - 4)) {
+		cap_vts = cap_shutter + 4;
+		ret = ov5640_set_vts(sensor, cap_vts);
+		if (ret < 0)
+			return ret;
+	}
+
+	return ov5640_set_exposure(sensor, cap_shutter);
+}
+
+/*
+ * if sensor changes inside scaling or subsampling
+ * change mode directly
+ */
+static int ov5640_set_mode_direct(struct ov5640_dev *sensor,
+				  const struct ov5640_mode_info *mode)
+{
+	int ret;
+
+	if (mode->reg_data == NULL)
+		return -EINVAL;
+
+	/* turn off AE/AG */
+	ret = ov5640_set_agc_aec(sensor, false);
+	if (ret < 0)
+		return ret;
+
+	/* Write capture setting */
+	ret = ov5640_load_regs(sensor, mode);
+	if (ret < 0)
+		return ret;
+
+	return ov5640_set_agc_aec(sensor, true);
+}
+
+static int ov5640_set_mode(struct ov5640_dev *sensor,
+			   const struct ov5640_mode_info *orig_mode)
+{
+	const struct ov5640_mode_info *mode = sensor->current_mode;
+	enum ov5640_downsize_mode dn_mode, orig_dn_mode;
+	int ret;
+
+	dn_mode = mode->dn_mode;
+	orig_dn_mode = orig_mode->dn_mode;
+
+	if ((dn_mode == SUBSAMPLING && orig_dn_mode == SCALING) ||
+	    (dn_mode == SCALING && orig_dn_mode == SUBSAMPLING)) {
+		/*
+		 * change between subsampling and scaling
+		 * go through exposure calucation
+		 */
+		ret = ov5640_set_mode_exposure_calc(sensor, mode);
+	} else {
+		/*
+		 * change inside subsampling or scaling
+		 * download firmware directly
+		 */
+		ret = ov5640_set_mode_direct(sensor, mode);
+	}
+
+	if (ret < 0)
+		return ret;
+
+	ret = ov5640_set_ae_target(sensor, sensor->ae_target);
+	if (ret < 0)
+		return ret;
+	ret = ov5640_get_light_freq(sensor);
+	if (ret < 0)
+		return ret;
+	ret = ov5640_set_bandingfilter(sensor);
+	if (ret < 0)
+		return ret;
+	ret = ov5640_set_virtual_channel(sensor);
+	if (ret < 0)
+		return ret;
+
+	sensor->pending_mode_change = false;
+
+	return 0;
+}
+
+/* restore the last set video mode after chip power-on */
+static int ov5640_restore_mode(struct ov5640_dev *sensor)
+{
+	int ret;
+
+	/* first load the initial register values */
+	ret = ov5640_load_regs(sensor, &ov5640_mode_init_data);
+	if (ret < 0)
+		return ret;
+
+	/* now restore the last capture mode */
+	return ov5640_set_mode(sensor, &ov5640_mode_init_data);
+}
+
+static void ov5640_power(struct ov5640_dev *sensor, bool enable)
+{
+	if (sensor->pwdn_gpio)
+		gpiod_set_value(sensor->pwdn_gpio, enable ? 0 : 1);
+}
+
+static void ov5640_reset(struct ov5640_dev *sensor)
+{
+	if (!sensor->reset_gpio)
+		return;
+
+	gpiod_set_value(sensor->reset_gpio, 0);
+
+	/* camera power cycle */
+	ov5640_power(sensor, false);
+	usleep_range(5000, 10000);
+	ov5640_power(sensor, true);
+	usleep_range(5000, 10000);
+
+	gpiod_set_value(sensor->reset_gpio, 1);
+	usleep_range(1000, 2000);
+
+	gpiod_set_value(sensor->reset_gpio, 0);
+	usleep_range(5000, 10000);
+}
+
+static int ov5640_set_power(struct ov5640_dev *sensor, bool on)
+{
+	int ret = 0;
+
+	if (on) {
+		clk_prepare_enable(sensor->xclk);
+
+		ret = regulator_bulk_enable(OV5640_NUM_SUPPLIES,
+					    sensor->supplies);
+		if (ret)
+			goto xclk_off;
+
+		ov5640_reset(sensor);
+		ov5640_power(sensor, true);
+
+		ret = ov5640_init_slave_id(sensor);
+		if (ret)
+			goto power_off;
+
+		ret = ov5640_restore_mode(sensor);
+		if (ret)
+			goto power_off;
+
+		/*
+		 * start streaming briefly followed by stream off in
+		 * order to coax the clock lane into LP-11 state.
+		 */
+		ov5640_set_stream(sensor, true);
+		usleep_range(1000, 2000);
+		ov5640_set_stream(sensor, false);
+
+		return 0;
+	}
+
+power_off:
+	ov5640_power(sensor, false);
+	regulator_bulk_disable(OV5640_NUM_SUPPLIES, sensor->supplies);
+xclk_off:
+	clk_disable_unprepare(sensor->xclk);
+	return ret;
+}
+
+/* --------------- Subdev Operations --------------- */
+
+static int ov5640_s_power(struct v4l2_subdev *sd, int on)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	int ret = 0;
+
+	mutex_lock(&sensor->lock);
+
+	/*
+	 * If the power count is modified from 0 to != 0 or from != 0 to 0,
+	 * update the power state.
+	 */
+	if (sensor->power_count == !on) {
+		ret = ov5640_set_power(sensor, !!on);
+		if (ret)
+			goto out;
+	}
+
+	/* Update the power count. */
+	sensor->power_count += on ? 1 : -1;
+	WARN_ON(sensor->power_count < 0);
+out:
+	mutex_unlock(&sensor->lock);
+
+	if (on && !ret && sensor->power_count == 1) {
+		/* restore controls */
+		ret = v4l2_ctrl_handler_setup(&sensor->ctrls.handler);
+	}
+
+	return ret;
+}
+
+static int ov5640_try_frame_interval(struct ov5640_dev *sensor,
+				     struct v4l2_fract *fi,
+				     u32 width, u32 height)
+{
+	const struct ov5640_mode_info *mode;
+	u32 minfps, maxfps, fps;
+	int ret;
+
+	minfps = ov5640_framerates[OV5640_15_FPS];
+	maxfps = ov5640_framerates[OV5640_30_FPS];
+
+	if (fi->numerator == 0) {
+		fi->denominator = maxfps;
+		fi->numerator = 1;
+		return OV5640_30_FPS;
+	}
+
+	fps = DIV_ROUND_CLOSEST(fi->denominator, fi->numerator);
+
+	fi->numerator = 1;
+	if (fps > maxfps)
+		fi->denominator = maxfps;
+	else if (fps < minfps)
+		fi->denominator = minfps;
+	else if (2 * fps >= 2 * minfps + (maxfps - minfps))
+		fi->denominator = maxfps;
+	else
+		fi->denominator = minfps;
+
+	ret = (fi->denominator == minfps) ? OV5640_15_FPS : OV5640_30_FPS;
+
+	mode = ov5640_find_mode(sensor, ret, width, height, false);
+	return mode ? ret : -EINVAL;
+}
+
+static int ov5640_g_parm(struct v4l2_subdev *sd, struct v4l2_streamparm *a)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	struct v4l2_captureparm *cparm = &a->parm.capture;
+
+	if (a->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+		return -EINVAL;
+
+	mutex_lock(&sensor->lock);
+
+	/* This is the only case currently handled. */
+	memset(a, 0, sizeof(*a));
+	a->type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
+	cparm->capability = sensor->streamcap.capability;
+	cparm->timeperframe = sensor->streamcap.timeperframe;
+	cparm->capturemode = sensor->streamcap.capturemode;
+
+	mutex_unlock(&sensor->lock);
+
+	return 0;
+}
+
+static int ov5640_s_parm(struct v4l2_subdev *sd, struct v4l2_streamparm *a)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	struct v4l2_fract *tpf = &a->parm.capture.timeperframe;
+	const struct ov5640_mode_info *mode;
+	int frame_rate, ret = 0;
+
+	if (a->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+		return -EINVAL;
+
+	mutex_lock(&sensor->lock);
+
+	if (sensor->streaming) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	mode = sensor->current_mode;
+
+	frame_rate = ov5640_try_frame_interval(sensor, tpf,
+					       mode->width, mode->height);
+	if (frame_rate < 0) {
+		ret = frame_rate;
+		goto out;
+	}
+
+	sensor->current_fr = frame_rate;
+	sensor->streamcap.timeperframe = *tpf;
+	sensor->pending_mode_change = true;
+out:
+	mutex_unlock(&sensor->lock);
+	return 0;
+}
+
+static int ov5640_get_fmt(struct v4l2_subdev *sd,
+			  struct v4l2_subdev_pad_config *cfg,
+			  struct v4l2_subdev_format *format)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	struct v4l2_mbus_framefmt *fmt;
+
+	if (format->pad != 0)
+		return -EINVAL;
+
+	mutex_lock(&sensor->lock);
+
+	if (format->which == V4L2_SUBDEV_FORMAT_TRY)
+		fmt = v4l2_subdev_get_try_format(&sensor->sd, cfg,
+						 format->pad);
+	else
+		fmt = &sensor->fmt;
+
+	format->format = *fmt;
+
+	mutex_unlock(&sensor->lock);
+
+	return 0;
+}
+
+static int ov5640_try_fmt_internal(struct v4l2_subdev *sd,
+				   struct v4l2_mbus_framefmt *fmt,
+				   enum ov5640_frame_rate fr,
+				   const struct ov5640_mode_info **new_mode)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	const struct ov5640_mode_info *mode;
+
+	mode = ov5640_find_mode(sensor, fr, fmt->width, fmt->height, true);
+	if (!mode)
+		return -EINVAL;
+
+	fmt->width = mode->width;
+	fmt->height = mode->height;
+	fmt->code = sensor->fmt.code;
+
+	if (new_mode)
+		*new_mode = mode;
+	return 0;
+}
+
+static int ov5640_set_fmt(struct v4l2_subdev *sd,
+			  struct v4l2_subdev_pad_config *cfg,
+			  struct v4l2_subdev_format *format)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	const struct ov5640_mode_info *new_mode;
+	int ret;
+
+	if (format->pad != 0)
+		return -EINVAL;
+
+	mutex_lock(&sensor->lock);
+
+	if (sensor->streaming) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	ret = ov5640_try_fmt_internal(sd, &format->format,
+				      sensor->current_fr, &new_mode);
+	if (ret)
+		goto out;
+
+	if (format->which == V4L2_SUBDEV_FORMAT_TRY) {
+		struct v4l2_mbus_framefmt *fmt =
+			v4l2_subdev_get_try_format(sd, cfg, 0);
+
+		*fmt = format->format;
+		goto out;
+	}
+
+	sensor->current_mode = new_mode;
+	sensor->fmt = format->format;
+	sensor->pending_mode_change = true;
+out:
+	mutex_unlock(&sensor->lock);
+	return ret;
+}
+
+
+/*
+ * Sensor Controls.
+ */
+
+static int ov5640_g_volatile_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct v4l2_subdev *sd = ctrl_to_sd(ctrl);
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+
+	mutex_lock(&sensor->lock);
+
+	switch (ctrl->id) {
+	case V4L2_CID_AUTOGAIN:
+		if (!ctrl->val)
+			goto out;
+		sensor->ctrls.gain->val = ov5640_get_gain(sensor);
+		break;
+	case V4L2_CID_EXPOSURE_AUTO:
+		if (ctrl->val == V4L2_EXPOSURE_MANUAL)
+			goto out;
+		sensor->ctrls.exposure->val = ov5640_get_exposure(sensor);
+		break;
+	}
+
+out:
+	mutex_unlock(&sensor->lock);
+	return 0;
+}
+
+static int ov5640_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct v4l2_subdev *sd = ctrl_to_sd(ctrl);
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	int ret = 0;
+
+	mutex_lock(&sensor->lock);
+
+	/*
+	 * If the device is not powered up by the host driver do
+	 * not apply any controls to H/W at this time. Instead
+	 * the controls will be restored right after power-up.
+	 */
+	if (sensor->power_count == 0)
+		goto out;
+
+	switch (ctrl->id) {
+	case V4L2_CID_AUTOGAIN:
+		ret = ov5640_set_gain(sensor, ctrl->val);
+		break;
+	case V4L2_CID_EXPOSURE_AUTO:
+		ret = ov5640_set_exposure(sensor, ctrl->val);
+		break;
+	case V4L2_CID_AUTO_WHITE_BALANCE:
+		ret = ov5640_set_white_balance(sensor, ctrl->val);
+		break;
+	case V4L2_CID_HUE:
+		ret = ov5640_set_hue(sensor, ctrl->val);
+		break;
+	case V4L2_CID_CONTRAST:
+		ret = ov5640_set_contrast(sensor, ctrl->val);
+		break;
+	case V4L2_CID_SATURATION:
+		ret = ov5640_set_saturation(sensor, ctrl->val);
+		break;
+	case V4L2_CID_TEST_PATTERN:
+		ret = ov5640_set_test_pattern(sensor, ctrl->val);
+		break;
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+out:
+	mutex_unlock(&sensor->lock);
+	return ret;
+}
+
+static const struct v4l2_ctrl_ops ov5640_ctrl_ops = {
+	.g_volatile_ctrl = ov5640_g_volatile_ctrl,
+	.s_ctrl = ov5640_s_ctrl,
+};
+
+static const char * const test_pattern_menu[] = {
+	"Disabled",
+	"Color bars",
+};
+
+static int ov5640_init_controls(struct ov5640_dev *sensor)
+{
+	const struct v4l2_ctrl_ops *ops = &ov5640_ctrl_ops;
+	struct ov5640_ctrls *ctrls = &sensor->ctrls;
+	struct v4l2_ctrl_handler *hdl = &ctrls->handler;
+	int ret;
+
+	v4l2_ctrl_handler_init(hdl, 32);
+
+	/* Auto/manual white balance */
+	ctrls->auto_wb = v4l2_ctrl_new_std(hdl, ops,
+					   V4L2_CID_AUTO_WHITE_BALANCE,
+					   0, 1, 1, 1);
+	ctrls->blue_balance = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_BLUE_BALANCE,
+						0, 4095, 1, 0);
+	ctrls->red_balance = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_RED_BALANCE,
+					       0, 4095, 1, 0);
+	/* Auto/manual exposure */
+	ctrls->auto_exp = v4l2_ctrl_new_std_menu(hdl, ops,
+						 V4L2_CID_EXPOSURE_AUTO,
+						 V4L2_EXPOSURE_MANUAL, 0,
+						 V4L2_EXPOSURE_AUTO);
+	ctrls->exposure = v4l2_ctrl_new_std(hdl, ops,
+					    V4L2_CID_EXPOSURE_ABSOLUTE,
+					    0, 65535, 1, 0);
+	/* Auto/manual gain */
+	ctrls->auto_gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_AUTOGAIN,
+					     0, 1, 1, 1);
+	ctrls->gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_GAIN,
+					0, 1023, 1, 0);
+
+	ctrls->saturation = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_SATURATION,
+					      0, 255, 1, 64);
+	ctrls->hue = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_HUE,
+				       0, 359, 1, 0);
+	ctrls->contrast = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_CONTRAST,
+					    0, 255, 1, 0);
+	ctrls->test_pattern =
+		v4l2_ctrl_new_std_menu_items(hdl, ops, V4L2_CID_TEST_PATTERN,
+					     ARRAY_SIZE(test_pattern_menu) - 1,
+					     0, 0, test_pattern_menu);
+
+	if (hdl->error) {
+		ret = hdl->error;
+		goto free_ctrls;
+	}
+
+	ctrls->gain->flags |= V4L2_CTRL_FLAG_VOLATILE;
+	ctrls->exposure->flags |= V4L2_CTRL_FLAG_VOLATILE;
+
+	v4l2_ctrl_auto_cluster(3, &ctrls->auto_wb, 0, false);
+	v4l2_ctrl_auto_cluster(2, &ctrls->auto_gain, 0, true);
+	v4l2_ctrl_auto_cluster(2, &ctrls->auto_exp, 1, true);
+
+	sensor->sd.ctrl_handler = hdl;
+	return 0;
+
+free_ctrls:
+	v4l2_ctrl_handler_free(hdl);
+	return ret;
+}
+
+static int ov5640_enum_frame_size(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_pad_config *cfg,
+				  struct v4l2_subdev_frame_size_enum *fse)
+{
+	if (fse->pad != 0)
+		return -EINVAL;
+	if (fse->index >= OV5640_NUM_MODES)
+		return -EINVAL;
+
+	fse->min_width = fse->max_width =
+		ov5640_mode_data[0][fse->index].width;
+	fse->min_height = fse->max_height =
+		ov5640_mode_data[0][fse->index].height;
+
+	return 0;
+}
+
+static int ov5640_enum_frame_interval(
+	struct v4l2_subdev *sd,
+	struct v4l2_subdev_pad_config *cfg,
+	struct v4l2_subdev_frame_interval_enum *fie)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	struct v4l2_fract tpf;
+	int ret;
+
+	if (fie->pad != 0)
+		return -EINVAL;
+	if (fie->index >= OV5640_NUM_FRAMERATES)
+		return -EINVAL;
+
+	tpf.numerator = 1;
+	tpf.denominator = ov5640_framerates[fie->index];
+
+	ret = ov5640_try_frame_interval(sensor, &tpf,
+					fie->width, fie->height);
+	if (ret < 0)
+		return -EINVAL;
+
+	fie->interval = tpf;
+	return 0;
+}
+
+static int ov5640_g_frame_interval(struct v4l2_subdev *sd,
+				   struct v4l2_subdev_frame_interval *fi)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+
+	mutex_lock(&sensor->lock);
+	fi->interval = sensor->streamcap.timeperframe;
+	mutex_unlock(&sensor->lock);
+
+	return 0;
+}
+
+static int ov5640_s_frame_interval(struct v4l2_subdev *sd,
+				   struct v4l2_subdev_frame_interval *fi)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	const struct ov5640_mode_info *mode;
+	int frame_rate, ret = 0;
+
+	if (fi->pad != 0)
+		return -EINVAL;
+
+	mutex_lock(&sensor->lock);
+
+	if (sensor->streaming) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	mode = sensor->current_mode;
+
+	frame_rate = ov5640_try_frame_interval(sensor, &fi->interval,
+					       mode->width, mode->height);
+	if (frame_rate < 0)
+		frame_rate = OV5640_15_FPS;
+
+	sensor->current_fr = frame_rate;
+	sensor->streamcap.timeperframe = fi->interval;
+	sensor->pending_mode_change = true;
+out:
+	mutex_unlock(&sensor->lock);
+	return ret;
+}
+
+static int ov5640_enum_mbus_code(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_pad_config *cfg,
+				  struct v4l2_subdev_mbus_code_enum *code)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+
+	if (code->pad != 0)
+		return -EINVAL;
+	if (code->index != 0)
+		return -EINVAL;
+
+	code->code = sensor->fmt.code;
+
+	return 0;
+}
+
+static int ov5640_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	int ret = 0;
+
+	mutex_lock(&sensor->lock);
+
+	if (sensor->streaming == !enable) {
+		if (enable && sensor->pending_mode_change) {
+			ret = ov5640_set_mode(sensor, sensor->current_mode);
+			if (ret)
+				goto out;
+		}
+
+		ret = ov5640_set_stream(sensor, enable);
+		if (!ret)
+			sensor->streaming = enable;
+	}
+out:
+	mutex_unlock(&sensor->lock);
+	return ret;
+}
+
+static const struct v4l2_subdev_core_ops ov5640_core_ops = {
+	.s_power = ov5640_s_power,
+};
+
+static const struct v4l2_subdev_video_ops ov5640_video_ops = {
+	.s_parm = ov5640_s_parm,
+	.g_parm = ov5640_g_parm,
+	.g_frame_interval = ov5640_g_frame_interval,
+	.s_frame_interval = ov5640_s_frame_interval,
+	.s_stream = ov5640_s_stream,
+};
+
+static const struct v4l2_subdev_pad_ops ov5640_pad_ops = {
+	.enum_mbus_code = ov5640_enum_mbus_code,
+	.get_fmt = ov5640_get_fmt,
+	.set_fmt = ov5640_set_fmt,
+	.enum_frame_size = ov5640_enum_frame_size,
+	.enum_frame_interval = ov5640_enum_frame_interval,
+};
+
+static const struct v4l2_subdev_ops ov5640_subdev_ops = {
+	.core = &ov5640_core_ops,
+	.video = &ov5640_video_ops,
+	.pad = &ov5640_pad_ops,
+};
+
+static int ov5640_get_regulators(struct ov5640_dev *sensor)
+{
+	int i;
+
+	for (i = 0; i < OV5640_NUM_SUPPLIES; i++)
+		sensor->supplies[i].supply = ov5640_supply_name[i];
+
+	return devm_regulator_bulk_get(&sensor->i2c_client->dev,
+				       OV5640_NUM_SUPPLIES,
+				       sensor->supplies);
+}
+
+static int ov5640_probe(struct i2c_client *client,
+			const struct i2c_device_id *id)
+{
+	struct device *dev = &client->dev;
+	struct device_node *endpoint;
+	struct ov5640_dev *sensor;
+	int ret;
+
+	sensor = devm_kzalloc(dev, sizeof(*sensor), GFP_KERNEL);
+	if (!sensor)
+		return -ENOMEM;
+
+	sensor->i2c_client = client;
+	sensor->fmt.code = MEDIA_BUS_FMT_UYVY8_2X8;
+	sensor->fmt.width = 640;
+	sensor->fmt.height = 480;
+	sensor->fmt.field = V4L2_FIELD_NONE;
+	sensor->streamcap.capability = V4L2_CAP_TIMEPERFRAME;
+	sensor->streamcap.capturemode = 0;
+	sensor->streamcap.timeperframe.denominator =
+		ov5640_framerates[OV5640_30_FPS];
+	sensor->streamcap.timeperframe.numerator = 1;
+	sensor->current_fr = OV5640_30_FPS;
+	sensor->current_mode =
+		&ov5640_mode_data[OV5640_30_FPS][OV5640_MODE_VGA_640_480];
+	sensor->pending_mode_change = true;
+
+	sensor->ae_target = 52;
+
+	endpoint = of_graph_get_next_endpoint(client->dev.of_node, NULL);
+	if (!endpoint) {
+		dev_err(dev, "endpoint node not found\n");
+		return -EINVAL;
+	}
+
+	v4l2_of_parse_endpoint(endpoint, &sensor->ep);
+	of_node_put(endpoint);
+
+	if (sensor->ep.bus_type != V4L2_MBUS_CSI2) {
+		dev_err(dev, "invalid bus type, must be MIPI CSI2\n");
+		return -EINVAL;
+	}
+
+	/* get system clock (xclk) */
+	sensor->xclk = devm_clk_get(dev, "xclk");
+	if (IS_ERR(sensor->xclk)) {
+		dev_err(dev, "failed to get xclk\n");
+		return PTR_ERR(sensor->xclk);
+	}
+
+	sensor->xclk_freq = clk_get_rate(sensor->xclk);
+	if (sensor->xclk_freq < OV5640_XCLK_MIN ||
+	    sensor->xclk_freq > OV5640_XCLK_MAX) {
+		dev_err(dev, "xclk frequency out of range: %d Hz\n",
+			sensor->xclk_freq);
+		return -EINVAL;
+	}
+
+	/* request optional power down pin */
+	sensor->pwdn_gpio = devm_gpiod_get_optional(dev, "powerdown",
+						    GPIOD_OUT_HIGH);
+	/* request optional reset pin */
+	sensor->reset_gpio = devm_gpiod_get_optional(dev, "reset",
+						     GPIOD_OUT_HIGH);
+
+	v4l2_i2c_subdev_init(&sensor->sd, client, &ov5640_subdev_ops);
+
+	sensor->sd.flags = V4L2_SUBDEV_FL_HAS_DEVNODE;
+	sensor->pad.flags = MEDIA_PAD_FL_SOURCE;
+	sensor->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
+	ret = media_entity_pads_init(&sensor->sd.entity, 1, &sensor->pad);
+	if (ret)
+		return ret;
+
+	ret = ov5640_get_regulators(sensor);
+	if (ret)
+		return ret;
+
+	mutex_init(&sensor->lock);
+
+	ret = ov5640_init_controls(sensor);
+	if (ret)
+		goto entity_cleanup;
+
+	ret = v4l2_async_register_subdev(&sensor->sd);
+	if (ret)
+		goto free_ctrls;
+
+	return 0;
+
+free_ctrls:
+	v4l2_ctrl_handler_free(&sensor->ctrls.handler);
+entity_cleanup:
+	mutex_destroy(&sensor->lock);
+	media_entity_cleanup(&sensor->sd.entity);
+	regulator_bulk_disable(OV5640_NUM_SUPPLIES, sensor->supplies);
+	return ret;
+}
+
+static int ov5640_remove(struct i2c_client *client)
+{
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+
+	regulator_bulk_disable(OV5640_NUM_SUPPLIES, sensor->supplies);
+
+	v4l2_async_unregister_subdev(&sensor->sd);
+	mutex_destroy(&sensor->lock);
+	media_entity_cleanup(&sensor->sd.entity);
+	v4l2_ctrl_handler_free(&sensor->ctrls.handler);
+
+	return 0;
+}
+
+static const struct i2c_device_id ov5640_id[] = {
+	{"ov5640", 0},
+	{},
+};
+MODULE_DEVICE_TABLE(i2c, ov5640_id);
+
+static const struct of_device_id ov5640_dt_ids[] = {
+	{ .compatible = "ovti,ov5640" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, ov5640_dt_ids);
+
+static struct i2c_driver ov5640_i2c_driver = {
+	.driver = {
+		.name  = "ov5640",
+		.of_match_table	= ov5640_dt_ids,
+	},
+	.id_table = ov5640_id,
+	.probe    = ov5640_probe,
+	.remove   = ov5640_remove,
+};
+
+module_i2c_driver(ov5640_i2c_driver);
+
+MODULE_DESCRIPTION("OV5640 MIPI Camera Subdev Driver");
+MODULE_LICENSE("GPL");
-- 
2.7.4

[PATCH v5 19/39] [media] add Omnivision OV5640 sensor driver

[Steve Longerbeam]

This driver is based on ov5640_mipi.c from Freescale imx_3.10.17_1.0.0_beta
branch, modified heavily to bring forward to latest interfaces and code
cleanup.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/media/i2c/Kconfig  |    7 +
 drivers/media/i2c/Makefile |    1 +
 drivers/media/i2c/ov5640.c | 2231 ++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 2239 insertions(+)
 create mode 100644 drivers/media/i2c/ov5640.c

diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index cee1dae..bf67661 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -531,6 +531,13 @@ config VIDEO_OV2659
 	  To compile this driver as a module, choose M here: the
 	  module will be called ov2659.
 
+config VIDEO_OV5640
+	tristate "OmniVision OV5640 sensor support"
+	depends on GPIOLIB && VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API
+	---help---
+	  This is a V4L2 sensor-level driver for the Omnivision
+	  OV5640 camera sensor with a MIPI CSI-2 interface.
+
 config VIDEO_OV7640
 	tristate "OmniVision OV7640 sensor support"
 	depends on I2C && VIDEO_V4L2
diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index 5bc7bbe..3a9d73a 100644
--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -57,6 +57,7 @@ obj-$(CONFIG_VIDEO_VP27SMPX) += vp27smpx.o
 obj-$(CONFIG_VIDEO_SONY_BTF_MPX) += sony-btf-mpx.o
 obj-$(CONFIG_VIDEO_UPD64031A) += upd64031a.o
 obj-$(CONFIG_VIDEO_UPD64083) += upd64083.o
+obj-$(CONFIG_VIDEO_OV5640) += ov5640.o
 obj-$(CONFIG_VIDEO_OV7640) += ov7640.o
 obj-$(CONFIG_VIDEO_OV7670) += ov7670.o
 obj-$(CONFIG_VIDEO_OV9650) += ov9650.o
diff --git a/drivers/media/i2c/ov5640.c b/drivers/media/i2c/ov5640.c
new file mode 100644
index 0000000..2d78ec8
--- /dev/null
+++ b/drivers/media/i2c/ov5640.c
@@ -0,0 +1,2231 @@
+/*
+ * Copyright (C) 2011-2013 Freescale Semiconductor, Inc. All Rights Reserved.
+ * Copyright (C) 2014-2017 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/clkdev.h>
+#include <linux/ctype.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/gpio/consumer.h>
+#include <linux/regulator/consumer.h>
+#include <media/v4l2-async.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-of.h>
+#include <media/v4l2-subdev.h>
+
+/* min/typical/max system clock (xclk) frequencies */
+#define OV5640_XCLK_MIN  6000000
+#define OV5640_XCLK_MAX 24000000
+
+/*
+ * FIXME: there is no subdev API to set the MIPI CSI-2
+ * virtual channel yet, so this is hardcoded for now.
+ */
+#define OV5640_MIPI_VC	1
+
+#define OV5640_DEFAULT_SLAVE_ID 0x3c
+
+#define OV5640_REG_CHIP_ID		0x300a
+#define OV5640_REG_PAD_OUTPUT00		0x3019
+#define OV5640_REG_SC_PLL_CTRL0		0x3034
+#define OV5640_REG_SC_PLL_CTRL1		0x3035
+#define OV5640_REG_SC_PLL_CTRL2		0x3036
+#define OV5640_REG_SC_PLL_CTRL3		0x3037
+#define OV5640_REG_SLAVE_ID		0x3100
+#define OV5640_REG_SYS_ROOT_DIVIDER	0x3108
+#define OV5640_REG_AWB_R_GAIN		0x3400
+#define OV5640_REG_AWB_G_GAIN		0x3402
+#define OV5640_REG_AWB_B_GAIN		0x3404
+#define OV5640_REG_AWB_MANUAL_CTRL	0x3406
+#define OV5640_REG_AEC_PK_EXPOSURE_HI	0x3500
+#define OV5640_REG_AEC_PK_EXPOSURE_MED	0x3501
+#define OV5640_REG_AEC_PK_EXPOSURE_LO	0x3502
+#define OV5640_REG_AEC_PK_MANUAL	0x3503
+#define OV5640_REG_AEC_PK_REAL_GAIN	0x350a
+#define OV5640_REG_AEC_PK_VTS		0x350c
+#define OV5640_REG_TIMING_HTS		0x380c
+#define OV5640_REG_TIMING_VTS		0x380e
+#define OV5640_REG_TIMING_TC_REG21	0x3821
+#define OV5640_REG_AEC_CTRL00		0x3a00
+#define OV5640_REG_AEC_B50_STEP		0x3a08
+#define OV5640_REG_AEC_B60_STEP		0x3a0a
+#define OV5640_REG_AEC_CTRL0D		0x3a0d
+#define OV5640_REG_AEC_CTRL0E		0x3a0e
+#define OV5640_REG_AEC_CTRL0F		0x3a0f
+#define OV5640_REG_AEC_CTRL10		0x3a10
+#define OV5640_REG_AEC_CTRL11		0x3a11
+#define OV5640_REG_AEC_CTRL1B		0x3a1b
+#define OV5640_REG_AEC_CTRL1E		0x3a1e
+#define OV5640_REG_AEC_CTRL1F		0x3a1f
+#define OV5640_REG_HZ5060_CTRL00	0x3c00
+#define OV5640_REG_HZ5060_CTRL01	0x3c01
+#define OV5640_REG_SIGMADELTA_CTRL0C	0x3c0c
+#define OV5640_REG_FRAME_CTRL01		0x4202
+#define OV5640_REG_MIPI_CTRL00		0x4800
+#define OV5640_REG_DEBUG_MODE		0x4814
+#define OV5640_REG_PRE_ISP_TEST_SET1	0x503d
+#define OV5640_REG_SDE_CTRL0		0x5580
+#define OV5640_REG_SDE_CTRL1		0x5581
+#define OV5640_REG_SDE_CTRL3		0x5583
+#define OV5640_REG_SDE_CTRL4		0x5584
+#define OV5640_REG_SDE_CTRL5		0x5585
+#define OV5640_REG_AVG_READOUT		0x56a1
+
+enum ov5640_mode_id {
+	OV5640_MODE_QCIF_176_144 = 0,
+	OV5640_MODE_QVGA_320_240,
+	OV5640_MODE_VGA_640_480,
+	OV5640_MODE_NTSC_720_480,
+	OV5640_MODE_PAL_720_576,
+	OV5640_MODE_XGA_1024_768,
+	OV5640_MODE_720P_1280_720,
+	OV5640_MODE_1080P_1920_1080,
+	OV5640_MODE_QSXGA_2592_1944,
+	OV5640_NUM_MODES,
+};
+
+enum ov5640_frame_rate {
+	OV5640_15_FPS = 0,
+	OV5640_30_FPS,
+	OV5640_NUM_FRAMERATES,
+};
+
+static const int ov5640_framerates[] = {
+	[OV5640_15_FPS] = 15,
+	[OV5640_30_FPS] = 30,
+};
+
+/* regulator supplies */
+static const char * const ov5640_supply_name[] = {
+	"DOVDD", /* Digital I/O (1.8V) suppply */
+	"DVDD",  /* Digital Core (1.5V) supply */
+	"AVDD",  /* Analog (2.8V) supply */
+};
+
+#define OV5640_NUM_SUPPLIES ARRAY_SIZE(ov5640_supply_name)
+
+/*
+ * image size under 1280 * 960 are SUBSAMPLING
+ * image size upper 1280 * 960 are SCALING
+ */
+enum ov5640_downsize_mode {
+	SUBSAMPLING,
+	SCALING,
+};
+
+struct reg_value {
+	u16 reg_addr;
+	u8 val;
+	u8 mask;
+	u32 delay_ms;
+};
+
+struct ov5640_mode_info {
+	enum ov5640_mode_id id;
+	enum ov5640_downsize_mode dn_mode;
+	u32 width;
+	u32 height;
+	const struct reg_value *reg_data;
+	u32 reg_data_size;
+};
+
+struct ov5640_ctrls {
+	struct v4l2_ctrl_handler handler;
+	struct {
+		struct v4l2_ctrl *auto_exp;
+		struct v4l2_ctrl *exposure;
+	};
+	struct {
+		struct v4l2_ctrl *auto_wb;
+		struct v4l2_ctrl *blue_balance;
+		struct v4l2_ctrl *red_balance;
+	};
+	struct {
+		struct v4l2_ctrl *auto_gain;
+		struct v4l2_ctrl *gain;
+	};
+	struct v4l2_ctrl *brightness;
+	struct v4l2_ctrl *saturation;
+	struct v4l2_ctrl *contrast;
+	struct v4l2_ctrl *hue;
+	struct v4l2_ctrl *test_pattern;
+};
+
+struct ov5640_dev {
+	struct i2c_client *i2c_client;
+	struct v4l2_subdev sd;
+	struct media_pad pad;
+	struct v4l2_of_endpoint ep; /* the parsed DT endpoint info */
+	struct clk *xclk; /* system clock to OV5640 */
+	u32 xclk_freq;
+
+	struct regulator_bulk_data supplies[OV5640_NUM_SUPPLIES];
+	struct gpio_desc *reset_gpio;
+	struct gpio_desc *pwdn_gpio;
+
+	/* lock to protect all members below */
+	struct mutex lock;
+
+	int power_count;
+
+	struct v4l2_mbus_framefmt fmt;
+	struct v4l2_captureparm streamcap;
+
+	const struct ov5640_mode_info *current_mode;
+	enum ov5640_frame_rate current_fr;
+
+	struct ov5640_ctrls ctrls;
+
+	u32 prev_sysclk, prev_hts;
+	u32 ae_low, ae_high, ae_target;
+
+	bool pending_mode_change;
+	bool streaming;
+};
+
+static inline struct ov5640_dev *to_ov5640_dev(struct v4l2_subdev *sd)
+{
+	return container_of(sd, struct ov5640_dev, sd);
+}
+
+static inline struct v4l2_subdev *ctrl_to_sd(struct v4l2_ctrl *ctrl)
+{
+	return &container_of(ctrl->handler, struct ov5640_dev,
+			     ctrls.handler)->sd;
+}
+
+/*
+ * FIXME: all of these register tables are likely filled with
+ * entries that set the register to their power-on default values,
+ * and which are otherwise not touched by this driver. Those entries
+ * should be identified and removed to speed register load time
+ * over i2c.
+ */
+
+static const struct reg_value ov5640_init_setting_30fps_VGA[] = {
+
+	{0x3103, 0x11, 0, 0}, {0x3008, 0x82, 0, 5}, {0x3008, 0x42, 0, 0},
+	{0x3103, 0x03, 0, 0}, {0x3017, 0x00, 0, 0}, {0x3018, 0x00, 0, 0},
+	{0x3034, 0x18, 0, 0}, {0x3035, 0x14, 0, 0}, {0x3036, 0x38, 0, 0},
+	{0x3037, 0x13, 0, 0}, {0x3108, 0x01, 0, 0}, {0x3630, 0x36, 0, 0},
+	{0x3631, 0x0e, 0, 0}, {0x3632, 0xe2, 0, 0}, {0x3633, 0x12, 0, 0},
+	{0x3621, 0xe0, 0, 0}, {0x3704, 0xa0, 0, 0}, {0x3703, 0x5a, 0, 0},
+	{0x3715, 0x78, 0, 0}, {0x3717, 0x01, 0, 0}, {0x370b, 0x60, 0, 0},
+	{0x3705, 0x1a, 0, 0}, {0x3905, 0x02, 0, 0}, {0x3906, 0x10, 0, 0},
+	{0x3901, 0x0a, 0, 0}, {0x3731, 0x12, 0, 0}, {0x3600, 0x08, 0, 0},
+	{0x3601, 0x33, 0, 0}, {0x302d, 0x60, 0, 0}, {0x3620, 0x52, 0, 0},
+	{0x371b, 0x20, 0, 0}, {0x471c, 0x50, 0, 0}, {0x3a13, 0x43, 0, 0},
+	{0x3a18, 0x00, 0, 0}, {0x3a19, 0xf8, 0, 0}, {0x3635, 0x13, 0, 0},
+	{0x3636, 0x03, 0, 0}, {0x3634, 0x40, 0, 0}, {0x3622, 0x01, 0, 0},
+	{0x3c01, 0xa4, 0, 0}, {0x3c04, 0x28, 0, 0}, {0x3c05, 0x98, 0, 0},
+	{0x3c06, 0x00, 0, 0}, {0x3c07, 0x08, 0, 0}, {0x3c08, 0x00, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0x80, 0, 0}, {0x380a, 0x01, 0, 0},
+	{0x380b, 0xe0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x3000, 0x00, 0, 0},
+	{0x3002, 0x1c, 0, 0}, {0x3004, 0xff, 0, 0}, {0x3006, 0xc3, 0, 0},
+	{0x300e, 0x45, 0, 0}, {0x302e, 0x08, 0, 0}, {0x4300, 0x3f, 0, 0},
+	{0x501f, 0x00, 0, 0}, {0x4713, 0x03, 0, 0}, {0x4407, 0x04, 0, 0},
+	{0x440e, 0x00, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x4837, 0x0a, 0, 0}, {0x4800, 0x04, 0, 0}, {0x3824, 0x02, 0, 0},
+	{0x5000, 0xa7, 0, 0}, {0x5001, 0xa3, 0, 0}, {0x5180, 0xff, 0, 0},
+	{0x5181, 0xf2, 0, 0}, {0x5182, 0x00, 0, 0}, {0x5183, 0x14, 0, 0},
+	{0x5184, 0x25, 0, 0}, {0x5185, 0x24, 0, 0}, {0x5186, 0x09, 0, 0},
+	{0x5187, 0x09, 0, 0}, {0x5188, 0x09, 0, 0}, {0x5189, 0x88, 0, 0},
+	{0x518a, 0x54, 0, 0}, {0x518b, 0xee, 0, 0}, {0x518c, 0xb2, 0, 0},
+	{0x518d, 0x50, 0, 0}, {0x518e, 0x34, 0, 0}, {0x518f, 0x6b, 0, 0},
+	{0x5190, 0x46, 0, 0}, {0x5191, 0xf8, 0, 0}, {0x5192, 0x04, 0, 0},
+	{0x5193, 0x70, 0, 0}, {0x5194, 0xf0, 0, 0}, {0x5195, 0xf0, 0, 0},
+	{0x5196, 0x03, 0, 0}, {0x5197, 0x01, 0, 0}, {0x5198, 0x04, 0, 0},
+	{0x5199, 0x6c, 0, 0}, {0x519a, 0x04, 0, 0}, {0x519b, 0x00, 0, 0},
+	{0x519c, 0x09, 0, 0}, {0x519d, 0x2b, 0, 0}, {0x519e, 0x38, 0, 0},
+	{0x5381, 0x1e, 0, 0}, {0x5382, 0x5b, 0, 0}, {0x5383, 0x08, 0, 0},
+	{0x5384, 0x0a, 0, 0}, {0x5385, 0x7e, 0, 0}, {0x5386, 0x88, 0, 0},
+	{0x5387, 0x7c, 0, 0}, {0x5388, 0x6c, 0, 0}, {0x5389, 0x10, 0, 0},
+	{0x538a, 0x01, 0, 0}, {0x538b, 0x98, 0, 0}, {0x5300, 0x08, 0, 0},
+	{0x5301, 0x30, 0, 0}, {0x5302, 0x10, 0, 0}, {0x5303, 0x00, 0, 0},
+	{0x5304, 0x08, 0, 0}, {0x5305, 0x30, 0, 0}, {0x5306, 0x08, 0, 0},
+	{0x5307, 0x16, 0, 0}, {0x5309, 0x08, 0, 0}, {0x530a, 0x30, 0, 0},
+	{0x530b, 0x04, 0, 0}, {0x530c, 0x06, 0, 0}, {0x5480, 0x01, 0, 0},
+	{0x5481, 0x08, 0, 0}, {0x5482, 0x14, 0, 0}, {0x5483, 0x28, 0, 0},
+	{0x5484, 0x51, 0, 0}, {0x5485, 0x65, 0, 0}, {0x5486, 0x71, 0, 0},
+	{0x5487, 0x7d, 0, 0}, {0x5488, 0x87, 0, 0}, {0x5489, 0x91, 0, 0},
+	{0x548a, 0x9a, 0, 0}, {0x548b, 0xaa, 0, 0}, {0x548c, 0xb8, 0, 0},
+	{0x548d, 0xcd, 0, 0}, {0x548e, 0xdd, 0, 0}, {0x548f, 0xea, 0, 0},
+	{0x5490, 0x1d, 0, 0}, {0x5580, 0x02, 0, 0}, {0x5583, 0x40, 0, 0},
+	{0x5584, 0x10, 0, 0}, {0x5589, 0x10, 0, 0}, {0x558a, 0x00, 0, 0},
+	{0x558b, 0xf8, 0, 0}, {0x5800, 0x23, 0, 0}, {0x5801, 0x14, 0, 0},
+	{0x5802, 0x0f, 0, 0}, {0x5803, 0x0f, 0, 0}, {0x5804, 0x12, 0, 0},
+	{0x5805, 0x26, 0, 0}, {0x5806, 0x0c, 0, 0}, {0x5807, 0x08, 0, 0},
+	{0x5808, 0x05, 0, 0}, {0x5809, 0x05, 0, 0}, {0x580a, 0x08, 0, 0},
+	{0x580b, 0x0d, 0, 0}, {0x580c, 0x08, 0, 0}, {0x580d, 0x03, 0, 0},
+	{0x580e, 0x00, 0, 0}, {0x580f, 0x00, 0, 0}, {0x5810, 0x03, 0, 0},
+	{0x5811, 0x09, 0, 0}, {0x5812, 0x07, 0, 0}, {0x5813, 0x03, 0, 0},
+	{0x5814, 0x00, 0, 0}, {0x5815, 0x01, 0, 0}, {0x5816, 0x03, 0, 0},
+	{0x5817, 0x08, 0, 0}, {0x5818, 0x0d, 0, 0}, {0x5819, 0x08, 0, 0},
+	{0x581a, 0x05, 0, 0}, {0x581b, 0x06, 0, 0}, {0x581c, 0x08, 0, 0},
+	{0x581d, 0x0e, 0, 0}, {0x581e, 0x29, 0, 0}, {0x581f, 0x17, 0, 0},
+	{0x5820, 0x11, 0, 0}, {0x5821, 0x11, 0, 0}, {0x5822, 0x15, 0, 0},
+	{0x5823, 0x28, 0, 0}, {0x5824, 0x46, 0, 0}, {0x5825, 0x26, 0, 0},
+	{0x5826, 0x08, 0, 0}, {0x5827, 0x26, 0, 0}, {0x5828, 0x64, 0, 0},
+	{0x5829, 0x26, 0, 0}, {0x582a, 0x24, 0, 0}, {0x582b, 0x22, 0, 0},
+	{0x582c, 0x24, 0, 0}, {0x582d, 0x24, 0, 0}, {0x582e, 0x06, 0, 0},
+	{0x582f, 0x22, 0, 0}, {0x5830, 0x40, 0, 0}, {0x5831, 0x42, 0, 0},
+	{0x5832, 0x24, 0, 0}, {0x5833, 0x26, 0, 0}, {0x5834, 0x24, 0, 0},
+	{0x5835, 0x22, 0, 0}, {0x5836, 0x22, 0, 0}, {0x5837, 0x26, 0, 0},
+	{0x5838, 0x44, 0, 0}, {0x5839, 0x24, 0, 0}, {0x583a, 0x26, 0, 0},
+	{0x583b, 0x28, 0, 0}, {0x583c, 0x42, 0, 0}, {0x583d, 0xce, 0, 0},
+	{0x5025, 0x00, 0, 0}, {0x3a0f, 0x30, 0, 0}, {0x3a10, 0x28, 0, 0},
+	{0x3a1b, 0x30, 0, 0}, {0x3a1e, 0x26, 0, 0}, {0x3a11, 0x60, 0, 0},
+	{0x3a1f, 0x14, 0, 0}, {0x3008, 0x02, 0, 0}, {0x3c00, 0x04, 0, 300},
+};
+
+static const struct reg_value ov5640_setting_30fps_VGA_640_480[] = {
+
+	{0x3035, 0x14, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0x80, 0, 0}, {0x380a, 0x01, 0, 0},
+	{0x380b, 0xe0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x04, 0, 0}, {0x380f, 0x38, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x0e, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0}, {0x3503, 0x00, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_VGA_640_480[] = {
+	{0x3035, 0x22, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0x80, 0, 0}, {0x380a, 0x01, 0, 0},
+	{0x380b, 0xe0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_30fps_XGA_1024_768[] = {
+
+	{0x3035, 0x14, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0x80, 0, 0}, {0x380a, 0x01, 0, 0},
+	{0x380b, 0xe0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x04, 0, 0}, {0x380f, 0x38, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x0e, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0}, {0x3503, 0x00, 0, 0},
+	{0x3808, 0x04, 0, 0}, {0x3809, 0x00, 0, 0}, {0x380a, 0x03, 0, 0},
+	{0x380b, 0x00, 0, 0}, {0x3035, 0x12, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_XGA_1024_768[] = {
+	{0x3035, 0x22, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0x80, 0, 0}, {0x380a, 0x01, 0, 0},
+	{0x380b, 0xe0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0}, {0x3808, 0x04, 0, 0},
+	{0x3809, 0x00, 0, 0}, {0x380a, 0x03, 0, 0}, {0x380b, 0x00, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_30fps_QVGA_320_240[] = {
+	{0x3035, 0x14, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x01, 0, 0}, {0x3809, 0x40, 0, 0}, {0x380a, 0x00, 0, 0},
+	{0x380b, 0xf0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_QVGA_320_240[] = {
+	{0x3035, 0x22, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x01, 0, 0}, {0x3809, 0x40, 0, 0}, {0x380a, 0x00, 0, 0},
+	{0x380b, 0xf0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_30fps_QCIF_176_144[] = {
+	{0x3035, 0x14, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x00, 0, 0}, {0x3809, 0xb0, 0, 0}, {0x380a, 0x00, 0, 0},
+	{0x380b, 0x90, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+static const struct reg_value ov5640_setting_15fps_QCIF_176_144[] = {
+	{0x3035, 0x22, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x00, 0, 0}, {0x3809, 0xb0, 0, 0}, {0x380a, 0x00, 0, 0},
+	{0x380b, 0x90, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_30fps_NTSC_720_480[] = {
+	{0x3035, 0x12, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0xd0, 0, 0}, {0x380a, 0x01, 0, 0},
+	{0x380b, 0xe0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x3c, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_NTSC_720_480[] = {
+	{0x3035, 0x22, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0xd0, 0, 0}, {0x380a, 0x01, 0, 0},
+	{0x380b, 0xe0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x3c, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_30fps_PAL_720_576[] = {
+	{0x3035, 0x12, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0xd0, 0, 0}, {0x380a, 0x02, 0, 0},
+	{0x380b, 0x40, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x38, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_PAL_720_576[] = {
+	{0x3035, 0x22, 0, 0}, {0x3036, 0x38, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x04, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9b, 0, 0},
+	{0x3808, 0x02, 0, 0}, {0x3809, 0xd0, 0, 0}, {0x380a, 0x02, 0, 0},
+	{0x380b, 0x40, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x68, 0, 0},
+	{0x380e, 0x03, 0, 0}, {0x380f, 0xd8, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x38, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x06, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_30fps_720P_1280_720[] = {
+	{0x3008, 0x42, 0, 0},
+	{0x3035, 0x21, 0, 0}, {0x3036, 0x54, 0, 0}, {0x3c07, 0x07, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0xfa, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x06, 0, 0}, {0x3807, 0xa9, 0, 0},
+	{0x3808, 0x05, 0, 0}, {0x3809, 0x00, 0, 0}, {0x380a, 0x02, 0, 0},
+	{0x380b, 0xd0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x64, 0, 0},
+	{0x380e, 0x02, 0, 0}, {0x380f, 0xe4, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x04, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x02, 0, 0},
+	{0x3a03, 0xe4, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0xbc, 0, 0},
+	{0x3a0a, 0x01, 0, 0}, {0x3a0b, 0x72, 0, 0}, {0x3a0e, 0x01, 0, 0},
+	{0x3a0d, 0x02, 0, 0}, {0x3a14, 0x02, 0, 0}, {0x3a15, 0xe4, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x02, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x37, 0, 0}, {0x460c, 0x20, 0, 0},
+	{0x3824, 0x04, 0, 0}, {0x5001, 0x83, 0, 0}, {0x4005, 0x1a, 0, 0},
+	{0x3008, 0x02, 0, 0}, {0x3503, 0,    0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_720P_1280_720[] = {
+	{0x3035, 0x41, 0, 0}, {0x3036, 0x54, 0, 0}, {0x3c07, 0x07, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x41, 0, 0}, {0x3821, 0x07, 0, 0}, {0x3814, 0x31, 0, 0},
+	{0x3815, 0x31, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0xfa, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x06, 0, 0}, {0x3807, 0xa9, 0, 0},
+	{0x3808, 0x05, 0, 0}, {0x3809, 0x00, 0, 0}, {0x380a, 0x02, 0, 0},
+	{0x380b, 0xd0, 0, 0}, {0x380c, 0x07, 0, 0}, {0x380d, 0x64, 0, 0},
+	{0x380e, 0x02, 0, 0}, {0x380f, 0xe4, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x04, 0, 0},
+	{0x3618, 0x00, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3709, 0x52, 0, 0}, {0x370c, 0x03, 0, 0}, {0x3a02, 0x02, 0, 0},
+	{0x3a03, 0xe4, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0xbc, 0, 0},
+	{0x3a0a, 0x01, 0, 0}, {0x3a0b, 0x72, 0, 0}, {0x3a0e, 0x01, 0, 0},
+	{0x3a0d, 0x02, 0, 0}, {0x3a14, 0x02, 0, 0}, {0x3a15, 0xe4, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x02, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x37, 0, 0}, {0x460c, 0x20, 0, 0},
+	{0x3824, 0x04, 0, 0}, {0x5001, 0x83, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_30fps_1080P_1920_1080[] = {
+	{0x3008, 0x42, 0, 0},
+	{0x3035, 0x21, 0, 0}, {0x3036, 0x54, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x40, 0, 0}, {0x3821, 0x06, 0, 0}, {0x3814, 0x11, 0, 0},
+	{0x3815, 0x11, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x00, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9f, 0, 0},
+	{0x3808, 0x0a, 0, 0}, {0x3809, 0x20, 0, 0}, {0x380a, 0x07, 0, 0},
+	{0x380b, 0x98, 0, 0}, {0x380c, 0x0b, 0, 0}, {0x380d, 0x1c, 0, 0},
+	{0x380e, 0x07, 0, 0}, {0x380f, 0xb0, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x04, 0, 0},
+	{0x3618, 0x04, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x21, 0, 0},
+	{0x3709, 0x12, 0, 0}, {0x370c, 0x00, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x06, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0x83, 0, 0}, {0x3035, 0x11, 0, 0},
+	{0x3036, 0x54, 0, 0}, {0x3c07, 0x07, 0, 0}, {0x3c08, 0x00, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3800, 0x01, 0, 0}, {0x3801, 0x50, 0, 0}, {0x3802, 0x01, 0, 0},
+	{0x3803, 0xb2, 0, 0}, {0x3804, 0x08, 0, 0}, {0x3805, 0xef, 0, 0},
+	{0x3806, 0x05, 0, 0}, {0x3807, 0xf1, 0, 0}, {0x3808, 0x07, 0, 0},
+	{0x3809, 0x80, 0, 0}, {0x380a, 0x04, 0, 0}, {0x380b, 0x38, 0, 0},
+	{0x380c, 0x09, 0, 0}, {0x380d, 0xc4, 0, 0}, {0x380e, 0x04, 0, 0},
+	{0x380f, 0x60, 0, 0}, {0x3612, 0x2b, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3a02, 0x04, 0, 0}, {0x3a03, 0x60, 0, 0}, {0x3a08, 0x01, 0, 0},
+	{0x3a09, 0x50, 0, 0}, {0x3a0a, 0x01, 0, 0}, {0x3a0b, 0x18, 0, 0},
+	{0x3a0e, 0x03, 0, 0}, {0x3a0d, 0x04, 0, 0}, {0x3a14, 0x04, 0, 0},
+	{0x3a15, 0x60, 0, 0}, {0x4713, 0x02, 0, 0}, {0x4407, 0x04, 0, 0},
+	{0x460b, 0x37, 0, 0}, {0x460c, 0x20, 0, 0}, {0x3824, 0x04, 0, 0},
+	{0x4005, 0x1a, 0, 0}, {0x3008, 0x02, 0, 0},
+	{0x3503, 0, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_1080P_1920_1080[] = {
+	{0x3008, 0x42, 0, 0},
+	{0x3035, 0x21, 0, 0}, {0x3036, 0x54, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x40, 0, 0}, {0x3821, 0x06, 0, 0}, {0x3814, 0x11, 0, 0},
+	{0x3815, 0x11, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x00, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9f, 0, 0},
+	{0x3808, 0x0a, 0, 0}, {0x3809, 0x20, 0, 0}, {0x380a, 0x07, 0, 0},
+	{0x380b, 0x98, 0, 0}, {0x380c, 0x0b, 0, 0}, {0x380d, 0x1c, 0, 0},
+	{0x380e, 0x07, 0, 0}, {0x380f, 0xb0, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x04, 0, 0},
+	{0x3618, 0x04, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x21, 0, 0},
+	{0x3709, 0x12, 0, 0}, {0x370c, 0x00, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x06, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0x83, 0, 0}, {0x3035, 0x21, 0, 0},
+	{0x3036, 0x54, 0, 1}, {0x3c07, 0x07, 0, 0}, {0x3c08, 0x00, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3800, 0x01, 0, 0}, {0x3801, 0x50, 0, 0}, {0x3802, 0x01, 0, 0},
+	{0x3803, 0xb2, 0, 0}, {0x3804, 0x08, 0, 0}, {0x3805, 0xef, 0, 0},
+	{0x3806, 0x05, 0, 0}, {0x3807, 0xf1, 0, 0}, {0x3808, 0x07, 0, 0},
+	{0x3809, 0x80, 0, 0}, {0x380a, 0x04, 0, 0}, {0x380b, 0x38, 0, 0},
+	{0x380c, 0x09, 0, 0}, {0x380d, 0xc4, 0, 0}, {0x380e, 0x04, 0, 0},
+	{0x380f, 0x60, 0, 0}, {0x3612, 0x2b, 0, 0}, {0x3708, 0x64, 0, 0},
+	{0x3a02, 0x04, 0, 0}, {0x3a03, 0x60, 0, 0}, {0x3a08, 0x01, 0, 0},
+	{0x3a09, 0x50, 0, 0}, {0x3a0a, 0x01, 0, 0}, {0x3a0b, 0x18, 0, 0},
+	{0x3a0e, 0x03, 0, 0}, {0x3a0d, 0x04, 0, 0}, {0x3a14, 0x04, 0, 0},
+	{0x3a15, 0x60, 0, 0}, {0x4713, 0x02, 0, 0}, {0x4407, 0x04, 0, 0},
+	{0x460b, 0x37, 0, 0}, {0x460c, 0x20, 0, 0}, {0x3824, 0x04, 0, 0},
+	{0x4005, 0x1a, 0, 0}, {0x3008, 0x02, 0, 0}, {0x3503, 0, 0, 0},
+};
+
+static const struct reg_value ov5640_setting_15fps_QSXGA_2592_1944[] = {
+	{0x3820, 0x40, 0, 0}, {0x3821, 0x06, 0, 0},
+	{0x3035, 0x21, 0, 0}, {0x3036, 0x54, 0, 0}, {0x3c07, 0x08, 0, 0},
+	{0x3c09, 0x1c, 0, 0}, {0x3c0a, 0x9c, 0, 0}, {0x3c0b, 0x40, 0, 0},
+	{0x3820, 0x40, 0, 0}, {0x3821, 0x06, 0, 0}, {0x3814, 0x11, 0, 0},
+	{0x3815, 0x11, 0, 0}, {0x3800, 0x00, 0, 0}, {0x3801, 0x00, 0, 0},
+	{0x3802, 0x00, 0, 0}, {0x3803, 0x00, 0, 0}, {0x3804, 0x0a, 0, 0},
+	{0x3805, 0x3f, 0, 0}, {0x3806, 0x07, 0, 0}, {0x3807, 0x9f, 0, 0},
+	{0x3808, 0x0a, 0, 0}, {0x3809, 0x20, 0, 0}, {0x380a, 0x07, 0, 0},
+	{0x380b, 0x98, 0, 0}, {0x380c, 0x0b, 0, 0}, {0x380d, 0x1c, 0, 0},
+	{0x380e, 0x07, 0, 0}, {0x380f, 0xb0, 0, 0}, {0x3810, 0x00, 0, 0},
+	{0x3811, 0x10, 0, 0}, {0x3812, 0x00, 0, 0}, {0x3813, 0x04, 0, 0},
+	{0x3618, 0x04, 0, 0}, {0x3612, 0x29, 0, 0}, {0x3708, 0x21, 0, 0},
+	{0x3709, 0x12, 0, 0}, {0x370c, 0x00, 0, 0}, {0x3a02, 0x03, 0, 0},
+	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
+	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
+	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x06, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
+	{0x3824, 0x02, 0, 0}, {0x5001, 0x83, 0, 70},
+};
+
+/* power-on sensor init reg table */
+static const struct ov5640_mode_info ov5640_mode_init_data = {
+	0, SUBSAMPLING, 640, 480, ov5640_init_setting_30fps_VGA,
+	ARRAY_SIZE(ov5640_init_setting_30fps_VGA),
+};
+
+static const struct ov5640_mode_info
+ov5640_mode_data[OV5640_NUM_FRAMERATES][OV5640_NUM_MODES] = {
+	{
+		{OV5640_MODE_QCIF_176_144, SUBSAMPLING, 176, 144,
+		 ov5640_setting_15fps_QCIF_176_144,
+		 ARRAY_SIZE(ov5640_setting_15fps_QCIF_176_144)},
+		{OV5640_MODE_QVGA_320_240, SUBSAMPLING, 320,  240,
+		 ov5640_setting_15fps_QVGA_320_240,
+		 ARRAY_SIZE(ov5640_setting_15fps_QVGA_320_240)},
+		{OV5640_MODE_VGA_640_480, SUBSAMPLING, 640,  480,
+		 ov5640_setting_15fps_VGA_640_480,
+		 ARRAY_SIZE(ov5640_setting_15fps_VGA_640_480)},
+		{OV5640_MODE_NTSC_720_480, SUBSAMPLING, 720, 480,
+		 ov5640_setting_15fps_NTSC_720_480,
+		 ARRAY_SIZE(ov5640_setting_15fps_NTSC_720_480)},
+		{OV5640_MODE_PAL_720_576, SUBSAMPLING, 720, 576,
+		 ov5640_setting_15fps_PAL_720_576,
+		 ARRAY_SIZE(ov5640_setting_15fps_PAL_720_576)},
+		{OV5640_MODE_XGA_1024_768, SUBSAMPLING, 1024, 768,
+		 ov5640_setting_15fps_XGA_1024_768,
+		 ARRAY_SIZE(ov5640_setting_15fps_XGA_1024_768)},
+		{OV5640_MODE_720P_1280_720, SUBSAMPLING, 1280, 720,
+		 ov5640_setting_15fps_720P_1280_720,
+		 ARRAY_SIZE(ov5640_setting_15fps_720P_1280_720)},
+		{OV5640_MODE_1080P_1920_1080, SCALING, 1920, 1080,
+		 ov5640_setting_15fps_1080P_1920_1080,
+		 ARRAY_SIZE(ov5640_setting_15fps_1080P_1920_1080)},
+		{OV5640_MODE_QSXGA_2592_1944, SCALING, 2592, 1944,
+		 ov5640_setting_15fps_QSXGA_2592_1944,
+		 ARRAY_SIZE(ov5640_setting_15fps_QSXGA_2592_1944)},
+	}, {
+		{OV5640_MODE_QCIF_176_144, SUBSAMPLING, 176, 144,
+		 ov5640_setting_30fps_QCIF_176_144,
+		 ARRAY_SIZE(ov5640_setting_30fps_QCIF_176_144)},
+		{OV5640_MODE_QVGA_320_240, SUBSAMPLING, 320,  240,
+		 ov5640_setting_30fps_QVGA_320_240,
+		 ARRAY_SIZE(ov5640_setting_30fps_QVGA_320_240)},
+		{OV5640_MODE_VGA_640_480, SUBSAMPLING, 640,  480,
+		 ov5640_setting_30fps_VGA_640_480,
+		 ARRAY_SIZE(ov5640_setting_30fps_VGA_640_480)},
+		{OV5640_MODE_NTSC_720_480, SUBSAMPLING, 720, 480,
+		 ov5640_setting_30fps_NTSC_720_480,
+		 ARRAY_SIZE(ov5640_setting_30fps_NTSC_720_480)},
+		{OV5640_MODE_PAL_720_576, SUBSAMPLING, 720, 576,
+		 ov5640_setting_30fps_PAL_720_576,
+		 ARRAY_SIZE(ov5640_setting_30fps_PAL_720_576)},
+		{OV5640_MODE_XGA_1024_768, SUBSAMPLING, 1024, 768,
+		 ov5640_setting_30fps_XGA_1024_768,
+		 ARRAY_SIZE(ov5640_setting_30fps_XGA_1024_768)},
+		{OV5640_MODE_720P_1280_720, SUBSAMPLING, 1280, 720,
+		 ov5640_setting_30fps_720P_1280_720,
+		 ARRAY_SIZE(ov5640_setting_30fps_720P_1280_720)},
+		{OV5640_MODE_1080P_1920_1080, SCALING, 1920, 1080,
+		 ov5640_setting_30fps_1080P_1920_1080,
+		 ARRAY_SIZE(ov5640_setting_30fps_1080P_1920_1080)},
+		{OV5640_MODE_QSXGA_2592_1944, -1, 0, 0, NULL, 0},
+	},
+};
+
+static int ov5640_init_slave_id(struct ov5640_dev *sensor)
+{
+	struct i2c_client *client = sensor->i2c_client;
+	struct i2c_msg msg;
+	u8 buf[3];
+	int ret;
+
+	if (client->addr == OV5640_DEFAULT_SLAVE_ID)
+		return 0;
+
+	buf[0] = OV5640_REG_SLAVE_ID >> 8;
+	buf[1] = OV5640_REG_SLAVE_ID & 0xff;
+	buf[2] = client->addr << 1;
+
+	msg.addr = OV5640_DEFAULT_SLAVE_ID;
+	msg.flags = 0;
+	msg.buf = buf;
+	msg.len = sizeof(buf);
+
+	ret = i2c_transfer(client->adapter, &msg, 1);
+	if (ret < 0) {
+		dev_err(&client->dev, "%s: failed with %d\n", __func__, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int ov5640_write_reg(struct ov5640_dev *sensor, u16 reg, u8 val)
+{
+	struct i2c_client *client = sensor->i2c_client;
+	struct i2c_msg msg;
+	u8 buf[3];
+	int ret;
+
+	buf[0] = reg >> 8;
+	buf[1] = reg & 0xff;
+	buf[2] = val;
+
+	msg.addr = client->addr;
+	msg.flags = client->flags;
+	msg.buf = buf;
+	msg.len = sizeof(buf);
+
+	ret = i2c_transfer(client->adapter, &msg, 1);
+	if (ret < 0) {
+		v4l2_err(&sensor->sd, "%s: error: reg=%x, val=%x\n",
+			__func__, reg, val);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int ov5640_read_reg(struct ov5640_dev *sensor, u16 reg, u8 *val)
+{
+	struct i2c_client *client = sensor->i2c_client;
+	struct i2c_msg msg[2];
+	u8 buf[2];
+	int ret;
+
+	buf[0] = reg >> 8;
+	buf[1] = reg & 0xff;
+
+	msg[0].addr = client->addr;
+	msg[0].flags = client->flags;
+	msg[0].buf = buf;
+	msg[0].len = sizeof(buf);
+
+	msg[1].addr = client->addr;
+	msg[1].flags = client->flags | I2C_M_RD;
+	msg[1].buf = buf;
+	msg[1].len = 1;
+
+	ret = i2c_transfer(client->adapter, msg, 2);
+	if (ret < 0)
+		return ret;
+
+	*val = buf[0];
+	return 0;
+}
+
+static int ov5640_read_reg16(struct ov5640_dev *sensor, u16 reg, u16 *val)
+{
+	u8 hi, lo;
+
+	ov5640_read_reg(sensor, reg, &hi);
+	ov5640_read_reg(sensor, reg+1, &lo);
+
+	*val = ((u16)hi << 8) | (u16)lo;
+	return 0;
+}
+
+static int ov5640_write_reg16(struct ov5640_dev *sensor, u16 reg, u16 val)
+{
+	ov5640_write_reg(sensor, reg, val >> 8);
+	ov5640_write_reg(sensor, reg + 1, val & 0xff);
+	return 0;
+}
+
+static int ov5640_mod_reg(struct ov5640_dev *sensor, u16 reg,
+			  u8 mask, u8 val)
+{
+	u8 readval;
+
+	ov5640_read_reg(sensor, reg, &readval);
+
+	readval &= ~mask;
+	val &= mask;
+	val |= readval;
+
+	ov5640_write_reg(sensor, reg, val);
+	return 0;
+}
+
+/* download ov5640 settings to sensor through i2c */
+static int ov5640_load_regs(struct ov5640_dev *sensor,
+			    const struct ov5640_mode_info *mode)
+{
+	const struct reg_value *regs = mode->reg_data;
+	unsigned int i;
+	u32 delay_ms;
+	u16 reg_addr;
+	u8 mask, val;
+
+	for (i = 0; i < mode->reg_data_size; ++i, ++regs) {
+		delay_ms = regs->delay_ms;
+		reg_addr = regs->reg_addr;
+		val = regs->val;
+		mask = regs->mask;
+
+		if (mask)
+			ov5640_mod_reg(sensor, reg_addr, mask, val);
+		else
+			ov5640_write_reg(sensor, reg_addr, val);
+		if (delay_ms)
+			usleep_range(1000*delay_ms, 1000*delay_ms+100);
+	}
+
+	return 0;
+}
+
+static int ov5640_set_hue(struct ov5640_dev *sensor, int value)
+{
+	if (value) {
+		ov5640_mod_reg(sensor, OV5640_REG_SDE_CTRL0, BIT(0), BIT(0));
+		ov5640_write_reg16(sensor, OV5640_REG_SDE_CTRL1, value);
+	} else {
+		ov5640_mod_reg(sensor, OV5640_REG_SDE_CTRL0, BIT(0), 0);
+	}
+
+	return 0;
+}
+
+static int ov5640_set_contrast(struct ov5640_dev *sensor, int value)
+{
+	if (value) {
+		ov5640_mod_reg(sensor, OV5640_REG_SDE_CTRL0, BIT(2), BIT(2));
+		ov5640_write_reg(sensor, OV5640_REG_SDE_CTRL5, value & 0xff);
+	} else {
+		ov5640_mod_reg(sensor, OV5640_REG_SDE_CTRL0, BIT(2), 0);
+	}
+
+	return 0;
+}
+
+static int ov5640_set_saturation(struct ov5640_dev *sensor, int value)
+{
+	if (value) {
+		ov5640_mod_reg(sensor, OV5640_REG_SDE_CTRL0, BIT(1), BIT(1));
+		ov5640_write_reg(sensor, OV5640_REG_SDE_CTRL3, value & 0xff);
+		ov5640_write_reg(sensor, OV5640_REG_SDE_CTRL4, value & 0xff);
+	} else {
+		ov5640_mod_reg(sensor, OV5640_REG_SDE_CTRL0, BIT(1), 0);
+	}
+
+	return 0;
+}
+
+static int ov5640_set_white_balance(struct ov5640_dev *sensor, int awb)
+{
+	ov5640_mod_reg(sensor, OV5640_REG_AWB_MANUAL_CTRL,
+		       BIT(0), awb ? 0 : 1);
+
+	if (!awb) {
+		u16 red = (u16)sensor->ctrls.red_balance->val;
+		u16 blue = (u16)sensor->ctrls.blue_balance->val;
+
+		ov5640_write_reg16(sensor, OV5640_REG_AWB_R_GAIN, red);
+		ov5640_write_reg16(sensor, OV5640_REG_AWB_B_GAIN, blue);
+	}
+
+	return 0;
+}
+
+static int ov5640_set_exposure(struct ov5640_dev *sensor, int exp)
+{
+	struct ov5640_ctrls *ctrls = &sensor->ctrls;
+	bool auto_exposure = (exp == V4L2_EXPOSURE_AUTO);
+
+	if (ctrls->auto_exp->is_new) {
+		ov5640_mod_reg(sensor, OV5640_REG_AEC_PK_MANUAL,
+			       BIT(0), auto_exposure ? 0 : BIT(0));
+	}
+
+	if (!auto_exposure && ctrls->exposure->is_new) {
+		u16 max_exp;
+
+		ov5640_read_reg16(sensor, OV5640_REG_AEC_PK_VTS, &max_exp);
+		if (ctrls->exposure->val < max_exp) {
+			u32 exposure = ctrls->exposure->val << 4;
+
+			ov5640_write_reg(sensor, OV5640_REG_AEC_PK_EXPOSURE_LO,
+					 exposure & 0xff);
+			ov5640_write_reg(sensor, OV5640_REG_AEC_PK_EXPOSURE_MED,
+					 (exposure >> 8) & 0xff);
+			ov5640_write_reg(sensor, OV5640_REG_AEC_PK_EXPOSURE_HI,
+					 (exposure >> 16) & 0x0f);
+		}
+	}
+
+	return 0;
+}
+
+/* read exposure, in number of line periods */
+static int ov5640_get_exposure(struct ov5640_dev *sensor)
+{
+	u8 temp;
+	int exp;
+
+	ov5640_read_reg(sensor, OV5640_REG_AEC_PK_EXPOSURE_HI, &temp);
+	exp = ((int)temp & 0x0f) << 16;
+	ov5640_read_reg(sensor, OV5640_REG_AEC_PK_EXPOSURE_MED, &temp);
+	exp |= ((int)temp << 8);
+	ov5640_read_reg(sensor, OV5640_REG_AEC_PK_EXPOSURE_LO, &temp);
+	exp |= (int)temp;
+
+	return exp >> 4;
+}
+
+static int ov5640_set_gain(struct ov5640_dev *sensor, int auto_gain)
+{
+	struct ov5640_ctrls *ctrls = &sensor->ctrls;
+
+	if (ctrls->auto_gain->is_new) {
+		ov5640_mod_reg(sensor, OV5640_REG_AEC_PK_MANUAL,
+			       BIT(1), ctrls->auto_gain->val ? 0 : BIT(1));
+	}
+
+	if (!auto_gain && ctrls->gain->is_new) {
+		u16 gain = (u16)ctrls->gain->val;
+
+		ov5640_write_reg16(sensor, OV5640_REG_AEC_PK_REAL_GAIN,
+				   gain & 0x3ff);
+	}
+
+	return 0;
+}
+
+static int ov5640_get_gain(struct ov5640_dev *sensor)
+{
+	u16 gain;
+
+	ov5640_read_reg16(sensor, OV5640_REG_AEC_PK_REAL_GAIN, &gain);
+
+	return gain & 0x3ff;
+}
+
+static int ov5640_set_agc_aec(struct ov5640_dev *sensor, bool on)
+{
+	ov5640_mod_reg(sensor, OV5640_REG_AEC_PK_MANUAL,
+		       0x3, on ? 0 : 0x3);
+	return 0;
+}
+
+static int ov5640_set_test_pattern(struct ov5640_dev *sensor, int value)
+{
+	ov5640_mod_reg(sensor, OV5640_REG_PRE_ISP_TEST_SET1,
+		       0xa4, value ? 0xa4 : 0);
+	return 0;
+}
+
+static int ov5640_set_stream(struct ov5640_dev *sensor, bool on)
+{
+	ov5640_mod_reg(sensor, OV5640_REG_MIPI_CTRL00, BIT(5),
+		       on ? 0 : BIT(5));
+	ov5640_write_reg(sensor, OV5640_REG_PAD_OUTPUT00,
+			 on ? 0x00 : 0x70);
+	ov5640_write_reg(sensor, OV5640_REG_FRAME_CTRL01,
+			 on ? 0x00 : 0x0f);
+	return 0;
+}
+
+static int ov5640_get_sysclk(struct ov5640_dev *sensor)
+{
+	 /* calculate sysclk */
+	u32 xvclk = sensor->xclk_freq / 10000;
+	u32 multiplier, prediv, VCO, sysdiv, pll_rdiv;
+	u32 sclk_rdiv_map[] = {1, 2, 4, 8};
+	u32 bit_div2x = 1, sclk_rdiv, sysclk;
+	u8 temp1, temp2;
+
+	ov5640_read_reg(sensor, OV5640_REG_SC_PLL_CTRL0, &temp1);
+	temp2 = temp1 & 0x0f;
+	if (temp2 == 8 || temp2 == 10)
+		bit_div2x = temp2 / 2;
+
+	ov5640_read_reg(sensor, OV5640_REG_SC_PLL_CTRL1, &temp1);
+	sysdiv = temp1 >> 4;
+	if (sysdiv == 0)
+		sysdiv = 16;
+
+	ov5640_read_reg(sensor, OV5640_REG_SC_PLL_CTRL2, &temp1);
+	multiplier = temp1;
+
+	ov5640_read_reg(sensor, OV5640_REG_SC_PLL_CTRL3, &temp1);
+	prediv = temp1 & 0x0f;
+	pll_rdiv = ((temp1 >> 4) & 0x01) + 1;
+
+	ov5640_read_reg(sensor, OV5640_REG_SYS_ROOT_DIVIDER, &temp1);
+	temp2 = temp1 & 0x03;
+	sclk_rdiv = sclk_rdiv_map[temp2];
+
+	VCO = xvclk * multiplier / prediv;
+
+	sysclk = VCO / sysdiv / pll_rdiv * 2 / bit_div2x / sclk_rdiv;
+
+	return sysclk;
+}
+
+static int ov5640_set_night_mode(struct ov5640_dev *sensor)
+{
+	 /* read HTS from register settings */
+	u8 mode;
+
+	ov5640_read_reg(sensor, OV5640_REG_AEC_CTRL00, &mode);
+	mode &= 0xfb;
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL00, mode);
+	return 0;
+}
+
+static int ov5640_get_hts(struct ov5640_dev *sensor)
+{
+	/* read HTS from register settings */
+	u16 hts;
+
+	ov5640_read_reg16(sensor, OV5640_REG_TIMING_HTS, &hts);
+	return hts;
+}
+
+static int ov5640_get_vts(struct ov5640_dev *sensor)
+{
+	u16 vts;
+
+	ov5640_read_reg16(sensor, OV5640_REG_TIMING_VTS, &vts);
+	return vts;
+}
+
+static int ov5640_set_vts(struct ov5640_dev *sensor, int vts)
+{
+	ov5640_write_reg16(sensor, OV5640_REG_TIMING_VTS, vts);
+	return 0;
+}
+
+static int ov5640_get_light_freq(struct ov5640_dev *sensor)
+{
+	/* get banding filter value */
+	u8 temp, temp1;
+	int light_freq = 0;
+
+	ov5640_read_reg(sensor, OV5640_REG_HZ5060_CTRL01, &temp);
+
+	if (temp & 0x80) {
+		/* manual */
+		ov5640_read_reg(sensor, OV5640_REG_HZ5060_CTRL00, &temp1);
+		if (temp1 & 0x04) {
+			/* 50Hz */
+			light_freq = 50;
+		} else {
+			/* 60Hz */
+			light_freq = 60;
+		}
+	} else {
+		/* auto */
+		ov5640_read_reg(sensor, OV5640_REG_SIGMADELTA_CTRL0C,
+				&temp1);
+		if (temp1 & 0x01) {
+			/* 50Hz */
+			light_freq = 50;
+		} else {
+			/* 60Hz */
+		}
+	}
+
+	return light_freq;
+}
+
+static int ov5640_set_bandingfilter(struct ov5640_dev *sensor)
+{
+	u32 band_step60, max_band60, band_step50, max_band50, prev_vts;
+	int ret;
+
+	/* read preview PCLK */
+	ret = ov5640_get_sysclk(sensor);
+	if (ret < 0)
+		return ret;
+	sensor->prev_sysclk = ret;
+	/* read preview HTS */
+	ret = ov5640_get_hts(sensor);
+	if (ret < 0)
+		return ret;
+	sensor->prev_hts = ret;
+
+	/* read preview VTS */
+	ret = ov5640_get_vts(sensor);
+	if (ret < 0)
+		return ret;
+	prev_vts = ret;
+
+	/* calculate banding filter */
+	/* 60Hz */
+	band_step60 = sensor->prev_sysclk * 100 / sensor->prev_hts * 100/120;
+	ov5640_write_reg16(sensor, OV5640_REG_AEC_B60_STEP, band_step60);
+
+	max_band60 = (int)((prev_vts-4)/band_step60);
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL0D, max_band60);
+
+	/* 50Hz */
+	band_step50 = sensor->prev_sysclk * 100 / sensor->prev_hts;
+	ov5640_write_reg16(sensor, OV5640_REG_AEC_B50_STEP, band_step50);
+
+	max_band50 = (int)((prev_vts-4)/band_step50);
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL0E, max_band50);
+
+	return 0;
+}
+
+static int ov5640_set_ae_target(struct ov5640_dev *sensor, int target)
+{
+	/* stable in high */
+	u32 fast_high, fast_low;
+
+	sensor->ae_low = target * 23 / 25;	/* 0.92 */
+	sensor->ae_high = target * 27 / 25;	/* 1.08 */
+
+	fast_high = sensor->ae_high << 1;
+	if (fast_high > 255)
+		fast_high = 255;
+
+	fast_low = sensor->ae_low >> 1;
+
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL0F, sensor->ae_high);
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL10, sensor->ae_low);
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL1B, sensor->ae_high);
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL1E, sensor->ae_low);
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL11, fast_high);
+	ov5640_write_reg(sensor, OV5640_REG_AEC_CTRL1F, fast_low);
+
+	return 0;
+}
+
+static int ov5640_binning_on(struct ov5640_dev *sensor)
+{
+	u8 temp;
+
+	ov5640_read_reg(sensor, OV5640_REG_TIMING_TC_REG21, &temp);
+	temp &= 0xfe;
+
+	return temp ? 1 : 0;
+}
+
+static int ov5640_set_virtual_channel(struct ov5640_dev *sensor)
+{
+	u8 temp, channel = OV5640_MIPI_VC;
+
+	ov5640_read_reg(sensor, OV5640_REG_DEBUG_MODE, &temp);
+	temp &= ~(3 << 6);
+	temp |= (channel << 6);
+	ov5640_write_reg(sensor, OV5640_REG_DEBUG_MODE, temp);
+
+	return 0;
+}
+
+static const struct ov5640_mode_info *
+ov5640_find_mode(struct ov5640_dev *sensor, enum ov5640_frame_rate fr,
+		 int width, int height, bool nearest)
+{
+	const struct ov5640_mode_info *mode = NULL;
+	int i;
+
+	for (i = OV5640_NUM_MODES - 1; i >= 0; i--) {
+		mode = &ov5640_mode_data[fr][i];
+
+		if (!mode->reg_data)
+			continue;
+
+		if ((nearest && mode->width <= width &&
+		     mode->height <= height) ||
+		    (!nearest && mode->width == width &&
+		     mode->height == height))
+			break;
+	}
+
+	if (nearest && i < 0)
+		mode = &ov5640_mode_data[fr][0];
+
+	return mode;
+}
+
+/*
+ * sensor changes between scaling and subsampling, go through
+ * exposure calculation
+ */
+static int ov5640_set_mode_exposure_calc(
+	struct ov5640_dev *sensor, const struct ov5640_mode_info *mode)
+{
+	u32 prev_shutter, prev_gain16;
+	u32 cap_shutter, cap_gain16;
+	u32 cap_sysclk, cap_hts, cap_vts;
+	u32 light_freq, cap_bandfilt, cap_maxband;
+	u32 cap_gain16_shutter;
+	u8 average;
+	int ret;
+
+	if (mode->reg_data == NULL)
+		return -EINVAL;
+
+	/* turn off AE/AG */
+	ret = ov5640_set_agc_aec(sensor, false);
+	if (ret < 0)
+		return ret;
+
+	/* read preview shutter */
+	ret = ov5640_get_exposure(sensor);
+	if (ret < 0)
+		return ret;
+	prev_shutter = ret;
+	ret = ov5640_binning_on(sensor);
+	if (ret < 0)
+		return ret;
+	if (ret && mode->id != OV5640_MODE_720P_1280_720 &&
+	    mode->id != OV5640_MODE_1080P_1920_1080)
+		prev_shutter *= 2;
+
+	/* read preview gain */
+	ret = ov5640_get_gain(sensor);
+	if (ret < 0)
+		return ret;
+	prev_gain16 = ret;
+
+	/* get average */
+	ov5640_read_reg(sensor, OV5640_REG_AVG_READOUT, &average);
+
+	/* turn off night mode for capture */
+	ret = ov5640_set_night_mode(sensor);
+	if (ret < 0)
+		return ret;
+
+	/* Write capture setting */
+	ret = ov5640_load_regs(sensor, mode);
+	if (ret < 0)
+		return ret;
+
+	/* read capture VTS */
+	ret = ov5640_get_vts(sensor);
+	if (ret < 0)
+		return ret;
+	cap_vts = ret;
+	ret = ov5640_get_hts(sensor);
+	if (ret < 0)
+		return ret;
+	cap_hts = ret;
+	ret = ov5640_get_sysclk(sensor);
+	if (ret < 0)
+		return ret;
+	cap_sysclk = ret;
+
+	/* calculate capture banding filter */
+	ret = ov5640_get_light_freq(sensor);
+	if (ret < 0)
+		return ret;
+	light_freq = ret;
+
+	if (light_freq == 60) {
+		/* 60Hz */
+		cap_bandfilt = cap_sysclk * 100 / cap_hts * 100 / 120;
+	} else {
+		/* 50Hz */
+		cap_bandfilt = cap_sysclk * 100 / cap_hts;
+	}
+	cap_maxband = (int)((cap_vts - 4) / cap_bandfilt);
+
+	/* calculate capture shutter/gain16 */
+	if (average > sensor->ae_low && average < sensor->ae_high) {
+		/* in stable range */
+		cap_gain16_shutter =
+			prev_gain16 * prev_shutter *
+			cap_sysclk / sensor->prev_sysclk *
+			sensor->prev_hts / cap_hts *
+			sensor->ae_target / average;
+	} else {
+		cap_gain16_shutter =
+			prev_gain16 * prev_shutter *
+			cap_sysclk / sensor->prev_sysclk *
+			sensor->prev_hts / cap_hts;
+	}
+
+	/* gain to shutter */
+	if (cap_gain16_shutter < (cap_bandfilt * 16)) {
+		/* shutter < 1/100 */
+		cap_shutter = cap_gain16_shutter / 16;
+		if (cap_shutter < 1)
+			cap_shutter = 1;
+
+		cap_gain16 = cap_gain16_shutter / cap_shutter;
+		if (cap_gain16 < 16)
+			cap_gain16 = 16;
+	} else {
+		if (cap_gain16_shutter > (cap_bandfilt * cap_maxband * 16)) {
+			/* exposure reach max */
+			cap_shutter = cap_bandfilt * cap_maxband;
+			cap_gain16 = cap_gain16_shutter / cap_shutter;
+		} else {
+			/* 1/100 < (cap_shutter = n/100) =< max */
+			cap_shutter =
+				((int)(cap_gain16_shutter / 16 / cap_bandfilt))
+				* cap_bandfilt;
+			cap_gain16 = cap_gain16_shutter / cap_shutter;
+		}
+	}
+
+	/* write capture gain */
+	ret = ov5640_set_gain(sensor, cap_gain16);
+	if (ret < 0)
+		return ret;
+
+	/* write capture shutter */
+	if (cap_shutter > (cap_vts - 4)) {
+		cap_vts = cap_shutter + 4;
+		ret = ov5640_set_vts(sensor, cap_vts);
+		if (ret < 0)
+			return ret;
+	}
+
+	return ov5640_set_exposure(sensor, cap_shutter);
+}
+
+/*
+ * if sensor changes inside scaling or subsampling
+ * change mode directly
+ */
+static int ov5640_set_mode_direct(struct ov5640_dev *sensor,
+				  const struct ov5640_mode_info *mode)
+{
+	int ret;
+
+	if (mode->reg_data == NULL)
+		return -EINVAL;
+
+	/* turn off AE/AG */
+	ret = ov5640_set_agc_aec(sensor, false);
+	if (ret < 0)
+		return ret;
+
+	/* Write capture setting */
+	ret = ov5640_load_regs(sensor, mode);
+	if (ret < 0)
+		return ret;
+
+	return ov5640_set_agc_aec(sensor, true);
+}
+
+static int ov5640_set_mode(struct ov5640_dev *sensor,
+			   const struct ov5640_mode_info *orig_mode)
+{
+	const struct ov5640_mode_info *mode = sensor->current_mode;
+	enum ov5640_downsize_mode dn_mode, orig_dn_mode;
+	int ret;
+
+	dn_mode = mode->dn_mode;
+	orig_dn_mode = orig_mode->dn_mode;
+
+	if ((dn_mode == SUBSAMPLING && orig_dn_mode == SCALING) ||
+	    (dn_mode == SCALING && orig_dn_mode == SUBSAMPLING)) {
+		/*
+		 * change between subsampling and scaling
+		 * go through exposure calucation
+		 */
+		ret = ov5640_set_mode_exposure_calc(sensor, mode);
+	} else {
+		/*
+		 * change inside subsampling or scaling
+		 * download firmware directly
+		 */
+		ret = ov5640_set_mode_direct(sensor, mode);
+	}
+
+	if (ret < 0)
+		return ret;
+
+	ret = ov5640_set_ae_target(sensor, sensor->ae_target);
+	if (ret < 0)
+		return ret;
+	ret = ov5640_get_light_freq(sensor);
+	if (ret < 0)
+		return ret;
+	ret = ov5640_set_bandingfilter(sensor);
+	if (ret < 0)
+		return ret;
+	ret = ov5640_set_virtual_channel(sensor);
+	if (ret < 0)
+		return ret;
+
+	sensor->pending_mode_change = false;
+
+	return 0;
+}
+
+/* restore the last set video mode after chip power-on */
+static int ov5640_restore_mode(struct ov5640_dev *sensor)
+{
+	int ret;
+
+	/* first load the initial register values */
+	ret = ov5640_load_regs(sensor, &ov5640_mode_init_data);
+	if (ret < 0)
+		return ret;
+
+	/* now restore the last capture mode */
+	return ov5640_set_mode(sensor, &ov5640_mode_init_data);
+}
+
+static void ov5640_power(struct ov5640_dev *sensor, bool enable)
+{
+	if (sensor->pwdn_gpio)
+		gpiod_set_value(sensor->pwdn_gpio, enable ? 0 : 1);
+}
+
+static void ov5640_reset(struct ov5640_dev *sensor)
+{
+	if (!sensor->reset_gpio)
+		return;
+
+	gpiod_set_value(sensor->reset_gpio, 0);
+
+	/* camera power cycle */
+	ov5640_power(sensor, false);
+	usleep_range(5000, 10000);
+	ov5640_power(sensor, true);
+	usleep_range(5000, 10000);
+
+	gpiod_set_value(sensor->reset_gpio, 1);
+	usleep_range(1000, 2000);
+
+	gpiod_set_value(sensor->reset_gpio, 0);
+	usleep_range(5000, 10000);
+}
+
+static int ov5640_set_power(struct ov5640_dev *sensor, bool on)
+{
+	int ret = 0;
+
+	if (on) {
+		clk_prepare_enable(sensor->xclk);
+
+		ret = regulator_bulk_enable(OV5640_NUM_SUPPLIES,
+					    sensor->supplies);
+		if (ret)
+			goto xclk_off;
+
+		ov5640_reset(sensor);
+		ov5640_power(sensor, true);
+
+		ret = ov5640_init_slave_id(sensor);
+		if (ret)
+			goto power_off;
+
+		ret = ov5640_restore_mode(sensor);
+		if (ret)
+			goto power_off;
+
+		/*
+		 * start streaming briefly followed by stream off in
+		 * order to coax the clock lane into LP-11 state.
+		 */
+		ov5640_set_stream(sensor, true);
+		usleep_range(1000, 2000);
+		ov5640_set_stream(sensor, false);
+
+		return 0;
+	}
+
+power_off:
+	ov5640_power(sensor, false);
+	regulator_bulk_disable(OV5640_NUM_SUPPLIES, sensor->supplies);
+xclk_off:
+	clk_disable_unprepare(sensor->xclk);
+	return ret;
+}
+
+/* --------------- Subdev Operations --------------- */
+
+static int ov5640_s_power(struct v4l2_subdev *sd, int on)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	int ret = 0;
+
+	mutex_lock(&sensor->lock);
+
+	/*
+	 * If the power count is modified from 0 to != 0 or from != 0 to 0,
+	 * update the power state.
+	 */
+	if (sensor->power_count == !on) {
+		ret = ov5640_set_power(sensor, !!on);
+		if (ret)
+			goto out;
+	}
+
+	/* Update the power count. */
+	sensor->power_count += on ? 1 : -1;
+	WARN_ON(sensor->power_count < 0);
+out:
+	mutex_unlock(&sensor->lock);
+
+	if (on && !ret && sensor->power_count == 1) {
+		/* restore controls */
+		ret = v4l2_ctrl_handler_setup(&sensor->ctrls.handler);
+	}
+
+	return ret;
+}
+
+static int ov5640_try_frame_interval(struct ov5640_dev *sensor,
+				     struct v4l2_fract *fi,
+				     u32 width, u32 height)
+{
+	const struct ov5640_mode_info *mode;
+	u32 minfps, maxfps, fps;
+	int ret;
+
+	minfps = ov5640_framerates[OV5640_15_FPS];
+	maxfps = ov5640_framerates[OV5640_30_FPS];
+
+	if (fi->numerator == 0) {
+		fi->denominator = maxfps;
+		fi->numerator = 1;
+		return OV5640_30_FPS;
+	}
+
+	fps = DIV_ROUND_CLOSEST(fi->denominator, fi->numerator);
+
+	fi->numerator = 1;
+	if (fps > maxfps)
+		fi->denominator = maxfps;
+	else if (fps < minfps)
+		fi->denominator = minfps;
+	else if (2 * fps >= 2 * minfps + (maxfps - minfps))
+		fi->denominator = maxfps;
+	else
+		fi->denominator = minfps;
+
+	ret = (fi->denominator == minfps) ? OV5640_15_FPS : OV5640_30_FPS;
+
+	mode = ov5640_find_mode(sensor, ret, width, height, false);
+	return mode ? ret : -EINVAL;
+}
+
+static int ov5640_g_parm(struct v4l2_subdev *sd, struct v4l2_streamparm *a)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	struct v4l2_captureparm *cparm = &a->parm.capture;
+
+	if (a->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+		return -EINVAL;
+
+	mutex_lock(&sensor->lock);
+
+	/* This is the only case currently handled. */
+	memset(a, 0, sizeof(*a));
+	a->type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
+	cparm->capability = sensor->streamcap.capability;
+	cparm->timeperframe = sensor->streamcap.timeperframe;
+	cparm->capturemode = sensor->streamcap.capturemode;
+
+	mutex_unlock(&sensor->lock);
+
+	return 0;
+}
+
+static int ov5640_s_parm(struct v4l2_subdev *sd, struct v4l2_streamparm *a)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	struct v4l2_fract *tpf = &a->parm.capture.timeperframe;
+	const struct ov5640_mode_info *mode;
+	int frame_rate, ret = 0;
+
+	if (a->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+		return -EINVAL;
+
+	mutex_lock(&sensor->lock);
+
+	if (sensor->streaming) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	mode = sensor->current_mode;
+
+	frame_rate = ov5640_try_frame_interval(sensor, tpf,
+					       mode->width, mode->height);
+	if (frame_rate < 0) {
+		ret = frame_rate;
+		goto out;
+	}
+
+	sensor->current_fr = frame_rate;
+	sensor->streamcap.timeperframe = *tpf;
+	sensor->pending_mode_change = true;
+out:
+	mutex_unlock(&sensor->lock);
+	return 0;
+}
+
+static int ov5640_get_fmt(struct v4l2_subdev *sd,
+			  struct v4l2_subdev_pad_config *cfg,
+			  struct v4l2_subdev_format *format)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	struct v4l2_mbus_framefmt *fmt;
+
+	if (format->pad != 0)
+		return -EINVAL;
+
+	mutex_lock(&sensor->lock);
+
+	if (format->which == V4L2_SUBDEV_FORMAT_TRY)
+		fmt = v4l2_subdev_get_try_format(&sensor->sd, cfg,
+						 format->pad);
+	else
+		fmt = &sensor->fmt;
+
+	format->format = *fmt;
+
+	mutex_unlock(&sensor->lock);
+
+	return 0;
+}
+
+static int ov5640_try_fmt_internal(struct v4l2_subdev *sd,
+				   struct v4l2_mbus_framefmt *fmt,
+				   enum ov5640_frame_rate fr,
+				   const struct ov5640_mode_info **new_mode)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	const struct ov5640_mode_info *mode;
+
+	mode = ov5640_find_mode(sensor, fr, fmt->width, fmt->height, true);
+	if (!mode)
+		return -EINVAL;
+
+	fmt->width = mode->width;
+	fmt->height = mode->height;
+	fmt->code = sensor->fmt.code;
+
+	if (new_mode)
+		*new_mode = mode;
+	return 0;
+}
+
+static int ov5640_set_fmt(struct v4l2_subdev *sd,
+			  struct v4l2_subdev_pad_config *cfg,
+			  struct v4l2_subdev_format *format)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	const struct ov5640_mode_info *new_mode;
+	int ret;
+
+	if (format->pad != 0)
+		return -EINVAL;
+
+	mutex_lock(&sensor->lock);
+
+	if (sensor->streaming) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	ret = ov5640_try_fmt_internal(sd, &format->format,
+				      sensor->current_fr, &new_mode);
+	if (ret)
+		goto out;
+
+	if (format->which == V4L2_SUBDEV_FORMAT_TRY) {
+		struct v4l2_mbus_framefmt *fmt =
+			v4l2_subdev_get_try_format(sd, cfg, 0);
+
+		*fmt = format->format;
+		goto out;
+	}
+
+	sensor->current_mode = new_mode;
+	sensor->fmt = format->format;
+	sensor->pending_mode_change = true;
+out:
+	mutex_unlock(&sensor->lock);
+	return ret;
+}
+
+
+/*
+ * Sensor Controls.
+ */
+
+static int ov5640_g_volatile_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct v4l2_subdev *sd = ctrl_to_sd(ctrl);
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+
+	mutex_lock(&sensor->lock);
+
+	switch (ctrl->id) {
+	case V4L2_CID_AUTOGAIN:
+		if (!ctrl->val)
+			goto out;
+		sensor->ctrls.gain->val = ov5640_get_gain(sensor);
+		break;
+	case V4L2_CID_EXPOSURE_AUTO:
+		if (ctrl->val == V4L2_EXPOSURE_MANUAL)
+			goto out;
+		sensor->ctrls.exposure->val = ov5640_get_exposure(sensor);
+		break;
+	}
+
+out:
+	mutex_unlock(&sensor->lock);
+	return 0;
+}
+
+static int ov5640_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct v4l2_subdev *sd = ctrl_to_sd(ctrl);
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	int ret = 0;
+
+	mutex_lock(&sensor->lock);
+
+	/*
+	 * If the device is not powered up by the host driver do
+	 * not apply any controls to H/W at this time. Instead
+	 * the controls will be restored right after power-up.
+	 */
+	if (sensor->power_count == 0)
+		goto out;
+
+	switch (ctrl->id) {
+	case V4L2_CID_AUTOGAIN:
+		ret = ov5640_set_gain(sensor, ctrl->val);
+		break;
+	case V4L2_CID_EXPOSURE_AUTO:
+		ret = ov5640_set_exposure(sensor, ctrl->val);
+		break;
+	case V4L2_CID_AUTO_WHITE_BALANCE:
+		ret = ov5640_set_white_balance(sensor, ctrl->val);
+		break;
+	case V4L2_CID_HUE:
+		ret = ov5640_set_hue(sensor, ctrl->val);
+		break;
+	case V4L2_CID_CONTRAST:
+		ret = ov5640_set_contrast(sensor, ctrl->val);
+		break;
+	case V4L2_CID_SATURATION:
+		ret = ov5640_set_saturation(sensor, ctrl->val);
+		break;
+	case V4L2_CID_TEST_PATTERN:
+		ret = ov5640_set_test_pattern(sensor, ctrl->val);
+		break;
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+out:
+	mutex_unlock(&sensor->lock);
+	return ret;
+}
+
+static const struct v4l2_ctrl_ops ov5640_ctrl_ops = {
+	.g_volatile_ctrl = ov5640_g_volatile_ctrl,
+	.s_ctrl = ov5640_s_ctrl,
+};
+
+static const char * const test_pattern_menu[] = {
+	"Disabled",
+	"Color bars",
+};
+
+static int ov5640_init_controls(struct ov5640_dev *sensor)
+{
+	const struct v4l2_ctrl_ops *ops = &ov5640_ctrl_ops;
+	struct ov5640_ctrls *ctrls = &sensor->ctrls;
+	struct v4l2_ctrl_handler *hdl = &ctrls->handler;
+	int ret;
+
+	v4l2_ctrl_handler_init(hdl, 32);
+
+	/* Auto/manual white balance */
+	ctrls->auto_wb = v4l2_ctrl_new_std(hdl, ops,
+					   V4L2_CID_AUTO_WHITE_BALANCE,
+					   0, 1, 1, 1);
+	ctrls->blue_balance = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_BLUE_BALANCE,
+						0, 4095, 1, 0);
+	ctrls->red_balance = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_RED_BALANCE,
+					       0, 4095, 1, 0);
+	/* Auto/manual exposure */
+	ctrls->auto_exp = v4l2_ctrl_new_std_menu(hdl, ops,
+						 V4L2_CID_EXPOSURE_AUTO,
+						 V4L2_EXPOSURE_MANUAL, 0,
+						 V4L2_EXPOSURE_AUTO);
+	ctrls->exposure = v4l2_ctrl_new_std(hdl, ops,
+					    V4L2_CID_EXPOSURE_ABSOLUTE,
+					    0, 65535, 1, 0);
+	/* Auto/manual gain */
+	ctrls->auto_gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_AUTOGAIN,
+					     0, 1, 1, 1);
+	ctrls->gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_GAIN,
+					0, 1023, 1, 0);
+
+	ctrls->saturation = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_SATURATION,
+					      0, 255, 1, 64);
+	ctrls->hue = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_HUE,
+				       0, 359, 1, 0);
+	ctrls->contrast = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_CONTRAST,
+					    0, 255, 1, 0);
+	ctrls->test_pattern =
+		v4l2_ctrl_new_std_menu_items(hdl, ops, V4L2_CID_TEST_PATTERN,
+					     ARRAY_SIZE(test_pattern_menu) - 1,
+					     0, 0, test_pattern_menu);
+
+	if (hdl->error) {
+		ret = hdl->error;
+		goto free_ctrls;
+	}
+
+	ctrls->gain->flags |= V4L2_CTRL_FLAG_VOLATILE;
+	ctrls->exposure->flags |= V4L2_CTRL_FLAG_VOLATILE;
+
+	v4l2_ctrl_auto_cluster(3, &ctrls->auto_wb, 0, false);
+	v4l2_ctrl_auto_cluster(2, &ctrls->auto_gain, 0, true);
+	v4l2_ctrl_auto_cluster(2, &ctrls->auto_exp, 1, true);
+
+	sensor->sd.ctrl_handler = hdl;
+	return 0;
+
+free_ctrls:
+	v4l2_ctrl_handler_free(hdl);
+	return ret;
+}
+
+static int ov5640_enum_frame_size(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_pad_config *cfg,
+				  struct v4l2_subdev_frame_size_enum *fse)
+{
+	if (fse->pad != 0)
+		return -EINVAL;
+	if (fse->index >= OV5640_NUM_MODES)
+		return -EINVAL;
+
+	fse->min_width = fse->max_width =
+		ov5640_mode_data[0][fse->index].width;
+	fse->min_height = fse->max_height =
+		ov5640_mode_data[0][fse->index].height;
+
+	return 0;
+}
+
+static int ov5640_enum_frame_interval(
+	struct v4l2_subdev *sd,
+	struct v4l2_subdev_pad_config *cfg,
+	struct v4l2_subdev_frame_interval_enum *fie)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	struct v4l2_fract tpf;
+	int ret;
+
+	if (fie->pad != 0)
+		return -EINVAL;
+	if (fie->index >= OV5640_NUM_FRAMERATES)
+		return -EINVAL;
+
+	tpf.numerator = 1;
+	tpf.denominator = ov5640_framerates[fie->index];
+
+	ret = ov5640_try_frame_interval(sensor, &tpf,
+					fie->width, fie->height);
+	if (ret < 0)
+		return -EINVAL;
+
+	fie->interval = tpf;
+	return 0;
+}
+
+static int ov5640_g_frame_interval(struct v4l2_subdev *sd,
+				   struct v4l2_subdev_frame_interval *fi)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+
+	mutex_lock(&sensor->lock);
+	fi->interval = sensor->streamcap.timeperframe;
+	mutex_unlock(&sensor->lock);
+
+	return 0;
+}
+
+static int ov5640_s_frame_interval(struct v4l2_subdev *sd,
+				   struct v4l2_subdev_frame_interval *fi)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	const struct ov5640_mode_info *mode;
+	int frame_rate, ret = 0;
+
+	if (fi->pad != 0)
+		return -EINVAL;
+
+	mutex_lock(&sensor->lock);
+
+	if (sensor->streaming) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	mode = sensor->current_mode;
+
+	frame_rate = ov5640_try_frame_interval(sensor, &fi->interval,
+					       mode->width, mode->height);
+	if (frame_rate < 0)
+		frame_rate = OV5640_15_FPS;
+
+	sensor->current_fr = frame_rate;
+	sensor->streamcap.timeperframe = fi->interval;
+	sensor->pending_mode_change = true;
+out:
+	mutex_unlock(&sensor->lock);
+	return ret;
+}
+
+static int ov5640_enum_mbus_code(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_pad_config *cfg,
+				  struct v4l2_subdev_mbus_code_enum *code)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+
+	if (code->pad != 0)
+		return -EINVAL;
+	if (code->index != 0)
+		return -EINVAL;
+
+	code->code = sensor->fmt.code;
+
+	return 0;
+}
+
+static int ov5640_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+	int ret = 0;
+
+	mutex_lock(&sensor->lock);
+
+	if (sensor->streaming == !enable) {
+		if (enable && sensor->pending_mode_change) {
+			ret = ov5640_set_mode(sensor, sensor->current_mode);
+			if (ret)
+				goto out;
+		}
+
+		ret = ov5640_set_stream(sensor, enable);
+		if (!ret)
+			sensor->streaming = enable;
+	}
+out:
+	mutex_unlock(&sensor->lock);
+	return ret;
+}
+
+static const struct v4l2_subdev_core_ops ov5640_core_ops = {
+	.s_power = ov5640_s_power,
+};
+
+static const struct v4l2_subdev_video_ops ov5640_video_ops = {
+	.s_parm = ov5640_s_parm,
+	.g_parm = ov5640_g_parm,
+	.g_frame_interval = ov5640_g_frame_interval,
+	.s_frame_interval = ov5640_s_frame_interval,
+	.s_stream = ov5640_s_stream,
+};
+
+static const struct v4l2_subdev_pad_ops ov5640_pad_ops = {
+	.enum_mbus_code = ov5640_enum_mbus_code,
+	.get_fmt = ov5640_get_fmt,
+	.set_fmt = ov5640_set_fmt,
+	.enum_frame_size = ov5640_enum_frame_size,
+	.enum_frame_interval = ov5640_enum_frame_interval,
+};
+
+static const struct v4l2_subdev_ops ov5640_subdev_ops = {
+	.core = &ov5640_core_ops,
+	.video = &ov5640_video_ops,
+	.pad = &ov5640_pad_ops,
+};
+
+static int ov5640_get_regulators(struct ov5640_dev *sensor)
+{
+	int i;
+
+	for (i = 0; i < OV5640_NUM_SUPPLIES; i++)
+		sensor->supplies[i].supply = ov5640_supply_name[i];
+
+	return devm_regulator_bulk_get(&sensor->i2c_client->dev,
+				       OV5640_NUM_SUPPLIES,
+				       sensor->supplies);
+}
+
+static int ov5640_probe(struct i2c_client *client,
+			const struct i2c_device_id *id)
+{
+	struct device *dev = &client->dev;
+	struct device_node *endpoint;
+	struct ov5640_dev *sensor;
+	int ret;
+
+	sensor = devm_kzalloc(dev, sizeof(*sensor), GFP_KERNEL);
+	if (!sensor)
+		return -ENOMEM;
+
+	sensor->i2c_client = client;
+	sensor->fmt.code = MEDIA_BUS_FMT_UYVY8_2X8;
+	sensor->fmt.width = 640;
+	sensor->fmt.height = 480;
+	sensor->fmt.field = V4L2_FIELD_NONE;
+	sensor->streamcap.capability = V4L2_CAP_TIMEPERFRAME;
+	sensor->streamcap.capturemode = 0;
+	sensor->streamcap.timeperframe.denominator =
+		ov5640_framerates[OV5640_30_FPS];
+	sensor->streamcap.timeperframe.numerator = 1;
+	sensor->current_fr = OV5640_30_FPS;
+	sensor->current_mode =
+		&ov5640_mode_data[OV5640_30_FPS][OV5640_MODE_VGA_640_480];
+	sensor->pending_mode_change = true;
+
+	sensor->ae_target = 52;
+
+	endpoint = of_graph_get_next_endpoint(client->dev.of_node, NULL);
+	if (!endpoint) {
+		dev_err(dev, "endpoint node not found\n");
+		return -EINVAL;
+	}
+
+	v4l2_of_parse_endpoint(endpoint, &sensor->ep);
+	of_node_put(endpoint);
+
+	if (sensor->ep.bus_type != V4L2_MBUS_CSI2) {
+		dev_err(dev, "invalid bus type, must be MIPI CSI2\n");
+		return -EINVAL;
+	}
+
+	/* get system clock (xclk) */
+	sensor->xclk = devm_clk_get(dev, "xclk");
+	if (IS_ERR(sensor->xclk)) {
+		dev_err(dev, "failed to get xclk\n");
+		return PTR_ERR(sensor->xclk);
+	}
+
+	sensor->xclk_freq = clk_get_rate(sensor->xclk);
+	if (sensor->xclk_freq < OV5640_XCLK_MIN ||
+	    sensor->xclk_freq > OV5640_XCLK_MAX) {
+		dev_err(dev, "xclk frequency out of range: %d Hz\n",
+			sensor->xclk_freq);
+		return -EINVAL;
+	}
+
+	/* request optional power down pin */
+	sensor->pwdn_gpio = devm_gpiod_get_optional(dev, "powerdown",
+						    GPIOD_OUT_HIGH);
+	/* request optional reset pin */
+	sensor->reset_gpio = devm_gpiod_get_optional(dev, "reset",
+						     GPIOD_OUT_HIGH);
+
+	v4l2_i2c_subdev_init(&sensor->sd, client, &ov5640_subdev_ops);
+
+	sensor->sd.flags = V4L2_SUBDEV_FL_HAS_DEVNODE;
+	sensor->pad.flags = MEDIA_PAD_FL_SOURCE;
+	sensor->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
+	ret = media_entity_pads_init(&sensor->sd.entity, 1, &sensor->pad);
+	if (ret)
+		return ret;
+
+	ret = ov5640_get_regulators(sensor);
+	if (ret)
+		return ret;
+
+	mutex_init(&sensor->lock);
+
+	ret = ov5640_init_controls(sensor);
+	if (ret)
+		goto entity_cleanup;
+
+	ret = v4l2_async_register_subdev(&sensor->sd);
+	if (ret)
+		goto free_ctrls;
+
+	return 0;
+
+free_ctrls:
+	v4l2_ctrl_handler_free(&sensor->ctrls.handler);
+entity_cleanup:
+	mutex_destroy(&sensor->lock);
+	media_entity_cleanup(&sensor->sd.entity);
+	regulator_bulk_disable(OV5640_NUM_SUPPLIES, sensor->supplies);
+	return ret;
+}
+
+static int ov5640_remove(struct i2c_client *client)
+{
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct ov5640_dev *sensor = to_ov5640_dev(sd);
+
+	regulator_bulk_disable(OV5640_NUM_SUPPLIES, sensor->supplies);
+
+	v4l2_async_unregister_subdev(&sensor->sd);
+	mutex_destroy(&sensor->lock);
+	media_entity_cleanup(&sensor->sd.entity);
+	v4l2_ctrl_handler_free(&sensor->ctrls.handler);
+
+	return 0;
+}
+
+static const struct i2c_device_id ov5640_id[] = {
+	{"ov5640", 0},
+	{},
+};
+MODULE_DEVICE_TABLE(i2c, ov5640_id);
+
+static const struct of_device_id ov5640_dt_ids[] = {
+	{ .compatible = "ovti,ov5640" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, ov5640_dt_ids);
+
+static struct i2c_driver ov5640_i2c_driver = {
+	.driver = {
+		.name  = "ov5640",
+		.of_match_table	= ov5640_dt_ids,
+	},
+	.id_table = ov5640_id,
+	.probe    = ov5640_probe,
+	.remove   = ov5640_remove,
+};
+
+module_i2c_driver(ov5640_i2c_driver);
+
+MODULE_DESCRIPTION("OV5640 MIPI Camera Subdev Driver");
+MODULE_LICENSE("GPL");
-- 
2.7.4

[PATCH v5 20/39] platform: add video-multiplexer subdevice driver

[Steve Longerbeam]

From: Philipp Zabel <p.zabel@pengutronix.de>

This driver can handle SoC internal and external video bus multiplexers,
controlled either by register bit fields or by a GPIO. The subdevice
passes through frame interval and mbus configuration of the active input
to the output side.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>

- fixed a cut&paste error in vidsw_remove(): v4l2_async_register_subdev()
  should be unregister.

- added media_entity_cleanup() to vidsw_remove().

- added missing MODULE_DEVICE_TABLE().
  Suggested-by: Javier Martinez Canillas <javier@dowhile0.org>

- there was a line left over from a previous iteration that negated
  the new way of determining the pad count just before it which
  has been removed (num_pads = of_get_child_count(np)).

- enforce that output frame interval must mirror input frame interval
  in vidsw_s_frame_interval().

- init frame interval to a default 30 fps.

- add link_validate to media_entity_operations and v4l2_subdev_pad_ops.

- moved devicetree binding doc to a separate commit.

- Philipp Zabel has developed a set of patches that allow adding
  to the subdev async notifier waiting list using a chaining method
  from the async registered callbacks (v4l2_of_subdev_registered()
  and the prep patches for that). For now, I've removed the use of
  v4l2_of_subdev_registered() for the vidmux driver's registered
  callback. This doesn't affect the functionality of this driver,
  but allows for it to be merged now, before adding the chaining
  support.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/media/platform/Kconfig             |   8 +
 drivers/media/platform/Makefile            |   2 +
 drivers/media/platform/video-multiplexer.c | 498 +++++++++++++++++++++++++++++
 3 files changed, 508 insertions(+)
 create mode 100644 drivers/media/platform/video-multiplexer.c

diff --git a/drivers/media/platform/Kconfig b/drivers/media/platform/Kconfig
index 53f6f12..3226eb6 100644
--- a/drivers/media/platform/Kconfig
+++ b/drivers/media/platform/Kconfig
@@ -74,6 +74,14 @@ config VIDEO_M32R_AR_M64278
 	  To compile this driver as a module, choose M here: the
 	  module will be called arv.
 
+config VIDEO_MULTIPLEXER
+	tristate "Video Multiplexer"
+	depends on VIDEO_V4L2_SUBDEV_API && MEDIA_CONTROLLER
+	help
+	  This driver provides support for SoC internal N:1 video bus
+	  multiplexers controlled by register bitfields as well as external
+	  2:1 video multiplexers controlled by a single GPIO.
+
 config VIDEO_OMAP3
 	tristate "OMAP 3 Camera support"
 	depends on VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API && ARCH_OMAP3
diff --git a/drivers/media/platform/Makefile b/drivers/media/platform/Makefile
index 8959f6e..d418add 100644
--- a/drivers/media/platform/Makefile
+++ b/drivers/media/platform/Makefile
@@ -27,6 +27,8 @@ obj-$(CONFIG_VIDEO_SH_VEU)		+= sh_veu.o
 
 obj-$(CONFIG_VIDEO_MEM2MEM_DEINTERLACE)	+= m2m-deinterlace.o
 
+obj-$(CONFIG_VIDEO_MULTIPLEXER)		+= video-multiplexer.o
+
 obj-$(CONFIG_VIDEO_S3C_CAMIF) 		+= s3c-camif/
 obj-$(CONFIG_VIDEO_SAMSUNG_EXYNOS4_IS) 	+= exynos4-is/
 obj-$(CONFIG_VIDEO_SAMSUNG_S5P_JPEG)	+= s5p-jpeg/
diff --git a/drivers/media/platform/video-multiplexer.c b/drivers/media/platform/video-multiplexer.c
new file mode 100644
index 0000000..02a21072
--- /dev/null
+++ b/drivers/media/platform/video-multiplexer.c
@@ -0,0 +1,498 @@
+/*
+ * video stream multiplexer controlled via gpio or syscon
+ *
+ * Copyright (C) 2013 Pengutronix, Sascha Hauer <kernel@pengutronix.de>
+ * Copyright (C) 2016 Pengutronix, Philipp Zabel <kernel@pengutronix.de>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/err.h>
+#include <linux/gpio/consumer.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_graph.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <media/v4l2-async.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-subdev.h>
+#include <media/v4l2-of.h>
+
+struct vidsw {
+	struct v4l2_subdev subdev;
+	unsigned int num_pads;
+	struct media_pad *pads;
+	struct v4l2_mbus_framefmt *format_mbus;
+	struct v4l2_fract timeperframe;
+	struct v4l2_of_endpoint *endpoint;
+	struct regmap_field *field;
+	struct gpio_desc *gpio;
+	int active;
+};
+
+static inline struct vidsw *v4l2_subdev_to_vidsw(struct v4l2_subdev *sd)
+{
+	return container_of(sd, struct vidsw, subdev);
+}
+
+static void vidsw_set_active(struct vidsw *vidsw, int active)
+{
+	vidsw->active = active;
+	if (active < 0)
+		return;
+
+	dev_dbg(vidsw->subdev.dev, "setting %d active\n", active);
+
+	if (vidsw->field)
+		regmap_field_write(vidsw->field, active);
+	else if (vidsw->gpio)
+		gpiod_set_value(vidsw->gpio, active);
+}
+
+static int vidsw_link_setup(struct media_entity *entity,
+			    const struct media_pad *local,
+			    const struct media_pad *remote, u32 flags)
+{
+	struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity);
+	struct vidsw *vidsw = v4l2_subdev_to_vidsw(sd);
+
+	/* We have no limitations on enabling or disabling our output link */
+	if (local->index == vidsw->num_pads - 1)
+		return 0;
+
+	dev_dbg(sd->dev, "link setup %s -> %s", remote->entity->name,
+		local->entity->name);
+
+	if (!(flags & MEDIA_LNK_FL_ENABLED)) {
+		if (local->index == vidsw->active) {
+			dev_dbg(sd->dev, "going inactive\n");
+			vidsw->active = -1;
+		}
+		return 0;
+	}
+
+	if (vidsw->active >= 0) {
+		struct media_pad *pad;
+
+		if (vidsw->active == local->index)
+			return 0;
+
+		pad = media_entity_remote_pad(&vidsw->pads[vidsw->active]);
+		if (pad) {
+			struct media_link *link;
+			int ret;
+
+			link = media_entity_find_link(pad,
+						&vidsw->pads[vidsw->active]);
+			if (link) {
+				ret = __media_entity_setup_link(link, 0);
+				if (ret)
+					return ret;
+			}
+		}
+	}
+
+	vidsw_set_active(vidsw, local->index);
+
+	return 0;
+}
+
+static struct media_entity_operations vidsw_ops = {
+	.link_setup = vidsw_link_setup,
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static bool vidsw_endpoint_disabled(struct device_node *ep)
+{
+	struct device_node *rpp;
+
+	if (!of_device_is_available(ep))
+		return true;
+
+	rpp = of_graph_get_remote_port_parent(ep);
+	if (!rpp)
+		return true;
+
+	return !of_device_is_available(rpp);
+}
+
+static int vidsw_async_init(struct vidsw *vidsw, struct device_node *node)
+{
+	struct device_node *ep;
+	u32 portno;
+	int numports;
+	int ret;
+	int i;
+	bool active_link = false;
+
+	numports = vidsw->num_pads;
+
+	for (i = 0; i < numports - 1; i++)
+		vidsw->pads[i].flags = MEDIA_PAD_FL_SINK;
+	vidsw->pads[numports - 1].flags = MEDIA_PAD_FL_SOURCE;
+
+	vidsw->subdev.entity.function = MEDIA_ENT_F_VID_MUX;
+	ret = media_entity_pads_init(&vidsw->subdev.entity, numports,
+				     vidsw->pads);
+	if (ret < 0)
+		return ret;
+
+	vidsw->subdev.entity.ops = &vidsw_ops;
+
+	for_each_endpoint_of_node(node, ep) {
+		struct v4l2_of_endpoint endpoint;
+
+		v4l2_of_parse_endpoint(ep, &endpoint);
+
+		portno = endpoint.base.port;
+		if (portno >= numports - 1)
+			continue;
+
+		if (vidsw_endpoint_disabled(ep)) {
+			dev_dbg(vidsw->subdev.dev,
+				"port %d disabled\n", portno);
+			continue;
+		}
+
+		vidsw->endpoint[portno] = endpoint;
+
+		if (portno == vidsw->active)
+			active_link = true;
+	}
+
+	for (portno = 0; portno < numports - 1; portno++) {
+		if (!vidsw->endpoint[portno].base.local_node)
+			continue;
+
+		/* If the active input is not connected, use another */
+		if (!active_link) {
+			vidsw_set_active(vidsw, portno);
+			active_link = true;
+		}
+	}
+
+	return v4l2_async_register_subdev(&vidsw->subdev);
+}
+
+int vidsw_g_mbus_config(struct v4l2_subdev *sd, struct v4l2_mbus_config *cfg)
+{
+	struct vidsw *vidsw = v4l2_subdev_to_vidsw(sd);
+	struct media_pad *pad;
+	int ret;
+
+	if (vidsw->active == -1) {
+		dev_err(sd->dev, "no configuration for inactive mux\n");
+		return -EINVAL;
+	}
+
+	/*
+	 * Retrieve media bus configuration from the entity connected to the
+	 * active input
+	 */
+	pad = media_entity_remote_pad(&vidsw->pads[vidsw->active]);
+	if (pad) {
+		sd = media_entity_to_v4l2_subdev(pad->entity);
+		ret = v4l2_subdev_call(sd, video, g_mbus_config, cfg);
+		if (ret == -ENOIOCTLCMD)
+			pad = NULL;
+		else if (ret < 0) {
+			dev_err(sd->dev, "failed to get source configuration\n");
+			return ret;
+		}
+	}
+	if (!pad) {
+		/* Mirror the input side on the output side */
+		cfg->type = vidsw->endpoint[vidsw->active].bus_type;
+		if (cfg->type == V4L2_MBUS_PARALLEL ||
+		    cfg->type == V4L2_MBUS_BT656)
+			cfg->flags = vidsw->endpoint[vidsw->active].bus.parallel.flags;
+	}
+
+	return 0;
+}
+
+static int vidsw_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct vidsw *vidsw = v4l2_subdev_to_vidsw(sd);
+	struct v4l2_subdev *upstream_sd;
+	struct media_pad *pad;
+
+	if (vidsw->active == -1) {
+		dev_err(sd->dev, "Can not start streaming on inactive mux\n");
+		return -EINVAL;
+	}
+
+	pad = media_entity_remote_pad(&sd->entity.pads[vidsw->active]);
+	if (!pad) {
+		dev_err(sd->dev, "Failed to find remote source pad\n");
+		return -ENOLINK;
+	}
+
+	if (!is_media_entity_v4l2_subdev(pad->entity)) {
+		dev_err(sd->dev, "Upstream entity is not a v4l2 subdev\n");
+		return -ENODEV;
+	}
+
+	upstream_sd = media_entity_to_v4l2_subdev(pad->entity);
+
+	return v4l2_subdev_call(upstream_sd, video, s_stream, enable);
+}
+
+static int vidsw_g_frame_interval(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_frame_interval *fi)
+{
+	struct vidsw *vidsw = v4l2_subdev_to_vidsw(sd);
+
+	fi->interval = vidsw->timeperframe;
+
+	return 0;
+}
+
+static int vidsw_s_frame_interval(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_frame_interval *fi)
+{
+	struct vidsw *vidsw = v4l2_subdev_to_vidsw(sd);
+
+	/* Output pad mirrors active input pad, no limits on input pads */
+	if (fi->pad == (vidsw->num_pads - 1))
+		fi->interval = vidsw->timeperframe;
+
+	vidsw->timeperframe = fi->interval;
+
+	return 0;
+}
+
+static const struct v4l2_subdev_video_ops vidsw_subdev_video_ops = {
+	.g_mbus_config = vidsw_g_mbus_config,
+	.s_stream = vidsw_s_stream,
+	.g_frame_interval = vidsw_g_frame_interval,
+	.s_frame_interval = vidsw_s_frame_interval,
+};
+
+static struct v4l2_mbus_framefmt *
+__vidsw_get_pad_format(struct v4l2_subdev *sd,
+		       struct v4l2_subdev_pad_config *cfg,
+		       unsigned int pad, u32 which)
+{
+	struct vidsw *vidsw = v4l2_subdev_to_vidsw(sd);
+
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		return v4l2_subdev_get_try_format(sd, cfg, pad);
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		return &vidsw->format_mbus[pad];
+	default:
+		return NULL;
+	}
+}
+
+static int vidsw_get_format(struct v4l2_subdev *sd,
+			    struct v4l2_subdev_pad_config *cfg,
+			    struct v4l2_subdev_format *sdformat)
+{
+	sdformat->format = *__vidsw_get_pad_format(sd, cfg, sdformat->pad,
+						   sdformat->which);
+	return 0;
+}
+
+static int vidsw_set_format(struct v4l2_subdev *sd,
+			    struct v4l2_subdev_pad_config *cfg,
+			    struct v4l2_subdev_format *sdformat)
+{
+	struct vidsw *vidsw = v4l2_subdev_to_vidsw(sd);
+	struct v4l2_mbus_framefmt *mbusformat;
+
+	if (sdformat->pad >= vidsw->num_pads)
+		return -EINVAL;
+
+	mbusformat = __vidsw_get_pad_format(sd, cfg, sdformat->pad,
+					    sdformat->which);
+	if (!mbusformat)
+		return -EINVAL;
+
+	/* Output pad mirrors active input pad, no limitations on input pads */
+	if (sdformat->pad == (vidsw->num_pads - 1) && vidsw->active >= 0)
+		sdformat->format = vidsw->format_mbus[vidsw->active];
+
+	*mbusformat = sdformat->format;
+
+	return 0;
+}
+
+static int vidsw_link_validate(struct v4l2_subdev *sd,
+			       struct media_link *link,
+			       struct v4l2_subdev_format *source_fmt,
+			       struct v4l2_subdev_format *sink_fmt)
+{
+	int ret;
+
+	ret = v4l2_subdev_link_validate_default(sd, link,
+						source_fmt, sink_fmt);
+	if (ret)
+		return ret;
+
+	return v4l2_subdev_link_validate_frame_interval(link);
+}
+
+static struct v4l2_subdev_pad_ops vidsw_pad_ops = {
+	.get_fmt = vidsw_get_format,
+	.set_fmt = vidsw_set_format,
+	.link_validate = vidsw_link_validate,
+};
+
+static struct v4l2_subdev_ops vidsw_subdev_ops = {
+	.pad = &vidsw_pad_ops,
+	.video = &vidsw_subdev_video_ops,
+};
+
+static int of_get_reg_field(struct device_node *node, struct reg_field *field)
+{
+	u32 bit_mask;
+	int ret;
+
+	ret = of_property_read_u32(node, "reg", &field->reg);
+	if (ret < 0)
+		return ret;
+
+	ret = of_property_read_u32(node, "bit-mask", &bit_mask);
+	if (ret < 0)
+		return ret;
+
+	ret = of_property_read_u32(node, "bit-shift", &field->lsb);
+	if (ret < 0)
+		return ret;
+
+	field->msb = field->lsb + fls(bit_mask) - 1;
+
+	return 0;
+}
+
+static int vidsw_probe(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct of_endpoint endpoint;
+	struct device_node *ep;
+	struct reg_field field;
+	struct vidsw *vidsw;
+	struct regmap *map;
+	unsigned int num_pads;
+	int ret;
+
+	vidsw = devm_kzalloc(&pdev->dev, sizeof(*vidsw), GFP_KERNEL);
+	if (!vidsw)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, vidsw);
+
+	v4l2_subdev_init(&vidsw->subdev, &vidsw_subdev_ops);
+	snprintf(vidsw->subdev.name, sizeof(vidsw->subdev.name), "%s",
+			np->name);
+	vidsw->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+	vidsw->subdev.dev = &pdev->dev;
+
+	/* init default frame interval */
+	vidsw->timeperframe.numerator = 1;
+	vidsw->timeperframe.denominator = 30;
+
+	/*
+	 * The largest numbered port is the output port. It determines
+	 * total number of pads
+	 */
+	num_pads = 0;
+	for_each_endpoint_of_node(np, ep) {
+		of_graph_parse_endpoint(ep, &endpoint);
+		num_pads = max(num_pads, endpoint.port + 1);
+	}
+
+	if (num_pads < 2) {
+		dev_err(&pdev->dev, "Not enough ports %d\n", num_pads);
+		return -EINVAL;
+	}
+
+	ret = of_get_reg_field(np, &field);
+	if (ret == 0) {
+		map = syscon_node_to_regmap(np->parent);
+		if (!map) {
+			dev_err(&pdev->dev, "Failed to get syscon register map\n");
+			return PTR_ERR(map);
+		}
+
+		vidsw->field = devm_regmap_field_alloc(&pdev->dev, map, field);
+		if (IS_ERR(vidsw->field)) {
+			dev_err(&pdev->dev, "Failed to allocate regmap field\n");
+			return PTR_ERR(vidsw->field);
+		}
+
+		regmap_field_read(vidsw->field, &vidsw->active);
+	} else {
+		if (num_pads > 3) {
+			dev_err(&pdev->dev, "Too many ports %d\n", num_pads);
+			return -EINVAL;
+		}
+
+		vidsw->gpio = devm_gpiod_get(&pdev->dev, NULL, GPIOD_OUT_LOW);
+		if (IS_ERR(vidsw->gpio)) {
+			dev_warn(&pdev->dev,
+				 "could not request control gpio: %d\n", ret);
+			vidsw->gpio = NULL;
+		}
+
+		vidsw->active = gpiod_get_value(vidsw->gpio) ? 1 : 0;
+	}
+
+	vidsw->num_pads = num_pads;
+	vidsw->pads = devm_kzalloc(&pdev->dev, sizeof(*vidsw->pads) * num_pads,
+			GFP_KERNEL);
+	vidsw->format_mbus = devm_kzalloc(&pdev->dev,
+			sizeof(*vidsw->format_mbus) * num_pads, GFP_KERNEL);
+	vidsw->endpoint = devm_kzalloc(&pdev->dev,
+			sizeof(*vidsw->endpoint) * (num_pads - 1), GFP_KERNEL);
+
+	ret = vidsw_async_init(vidsw, np);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int vidsw_remove(struct platform_device *pdev)
+{
+	struct vidsw *vidsw = platform_get_drvdata(pdev);
+	struct v4l2_subdev *sd = &vidsw->subdev;
+
+	v4l2_async_unregister_subdev(sd);
+	media_entity_cleanup(&sd->entity);
+
+	return 0;
+}
+
+static const struct of_device_id vidsw_dt_ids[] = {
+	{ .compatible = "video-multiplexer", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, vidsw_dt_ids);
+
+static struct platform_driver vidsw_driver = {
+	.probe		= vidsw_probe,
+	.remove		= vidsw_remove,
+	.driver		= {
+		.of_match_table = vidsw_dt_ids,
+		.name = "video-multiplexer",
+	},
+};
+
+module_platform_driver(vidsw_driver);
+
+MODULE_DESCRIPTION("video stream multiplexer");
+MODULE_AUTHOR("Sascha Hauer, Pengutronix");
+MODULE_AUTHOR("Philipp Zabel, Pengutronix");
+MODULE_LICENSE("GPL");
-- 
2.7.4

[PATCH v5 20/39] platform: add video-multiplexer subdevice driver

[Steve Longerbeam]

From: Philipp Zabel <p.zabel@pengutronix.de>

This driver can handle SoC internal and external video bus multiplexers,
controlled either by register bit fields or by a GPIO. The subdevice
passes through frame interval and mbus configuration of the active input
to the output side.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>

- fixed a cut&paste error in vidsw_remove(): v4l2_async_register_subdev()
  should be unregister.

- added media_entity_cleanup() to vidsw_remove().

- added missing MODULE_DEVICE_TABLE().
  Suggested-by: Javier Martinez Canillas <javier@dowhile0.org>

- there was a line left over from a previous iteration that negated
  the new way of determining the pad count just before it which
  has been removed (num_pads = of_get_child_count(np)).

- enforce that output frame interval must mirror input frame interval
  in vidsw_s_frame_interval().

- init frame interval to a default 30 fps.

- add link_validate to media_entity_operations and v4l2_subdev_pad_ops.

- moved devicetree binding doc to a separate commit.

- Philipp Zabel has developed a set of patches that allow adding
  to the subdev async notifier waiting list using a chaining method
  from the async registered callbacks (v4l2_of_subdev_registered()
  and the prep patches for that). For now, I've removed the use of
  v4l2_of_subdev_registered() for the vidmux driver's registered
  callback. This doesn't affect the functionality of this driver,
  but allows for it to be merged now, before adding the chaining
  support.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/media/platform/Kconfig             |   8 +
 drivers/media/platform/Makefile            |   2 +
 drivers/media/platform/video-multiplexer.c | 498 +++++++++++++++++++++++++++++
 3 files changed, 508 insertions(+)
 create mode 100644 drivers/media/platform/video-multiplexer.c

diff --git a/drivers/media/platform/Kconfig b/drivers/media/platform/Kconfig
index 53f6f12..3226eb6 100644
--- a/drivers/media/platform/Kconfig
+++ b/drivers/media/platform/Kconfig
@@ -74,6 +74,14 @@ config VIDEO_M32R_AR_M64278
 	  To compile this driver as a module, choose M here: the
 	  module will be called arv.
 
+config VIDEO_MULTIPLEXER
+	tristate "Video Multiplexer"
+	depends on VIDEO_V4L2_SUBDEV_API && MEDIA_CONTROLLER
+	help
+	  This driver provides support for SoC internal N:1 video bus
+	  multiplexers controlled by register bitfields as well as external
+	  2:1 video multiplexers controlled by a single GPIO.
+
 config VIDEO_OMAP3
 	tristate "OMAP 3 Camera support"
 	depends on VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API && ARCH_OMAP3
diff --git a/drivers/media/platform/Makefile b/drivers/media/platform/Makefile
index 8959f6e..d418add 100644
--- a/drivers/media/platform/Makefile
+++ b/drivers/media/platform/Makefile
@@ -27,6 +27,8 @@ obj-$(CONFIG_VIDEO_SH_VEU)		+= sh_veu.o
 
 obj-$(CONFIG_VIDEO_MEM2MEM_DEINTERLACE)	+= m2m-deinterlace.o
 
+obj-$(CONFIG_VIDEO_MULTIPLEXER)		+= video-multiplexer.o
+
 obj-$(CONFIG_VIDEO_S3C_CAMIF) 		+= s3c-camif/
 obj-$(CONFIG_VIDEO_SAMSUNG_EXYNOS4_IS) 	+= exynos4-is/
 obj-$(CONFIG_VIDEO_SAMSUNG_S5P_JPEG)	+= s5p-jpeg/
diff --git a/drivers/media/platform/video-multiplexer.c b/drivers/media/platform/video-multiplexer.c
new file mode 100644
index 0000000..02a21072
--- /dev/null
+++ b/drivers/media/platform/video-multiplexer.c
@@ -0,0 +1,498 @@
+/*
+ * video stream multiplexer controlled via gpio or syscon
+ *
+ * Copyright (C) 2013 Pengutronix, Sascha Hauer <kernel@pengutronix.de>
+ * Copyright (C) 2016 Pengutronix, Philipp Zabel <kernel@pengutronix.de>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/err.h>
+#include <linux/gpio/consumer.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_graph.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <media/v4l2-async.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-subdev.h>
+#include <media/v4l2-of.h>
+
+struct vidsw {
+	struct v4l2_subdev subdev;
+	unsigned int num_pads;
+	struct media_pad *pads;
+	struct v4l2_mbus_framefmt *format_mbus;
+	struct v4l2_fract timeperframe;
+	struct v4l2_of_endpoint *endpoint;
+	struct regmap_field *field;
+	struct gpio_desc *gpio;
+	int active;
+};
+
+static inline struct vidsw *v4l2_subdev_to_vidsw(struct v4l2_subdev *sd)
+{
+	return container_of(sd, struct vidsw, subdev);
+}
+
+static void vidsw_set_active(struct vidsw *vidsw, int active)
+{
+	vidsw->active = active;
+	if (active < 0)
+		return;
+
+	dev_dbg(vidsw->subdev.dev, "setting %d active\n", active);
+
+	if (vidsw->field)
+		regmap_field_write(vidsw->field, active);
+	else if (vidsw->gpio)
+		gpiod_set_value(vidsw->gpio, active);
+}
+
+static int vidsw_link_setup(struct media_entity *entity,
+			    const struct media_pad *local,
+			    const struct media_pad *remote, u32 flags)
+{
+	struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity);
+	struct vidsw *vidsw = v4l2_subdev_to_vidsw(sd);
+
+	/* We have no limitations on enabling or disabling our output link */
+	if (local->index == vidsw->num_pads - 1)
+		return 0;
+
+	dev_dbg(sd->dev, "link setup %s -> %s", remote->entity->name,
+		local->entity->name);
+
+	if (!(flags & MEDIA_LNK_FL_ENABLED)) {
+		if (local->index == vidsw->active) {
+			dev_dbg(sd->dev, "going inactive\n");
+			vidsw->active = -1;
+		}
+		return 0;
+	}
+
+	if (vidsw->active >= 0) {
+		struct media_pad *pad;
+
+		if (vidsw->active == local->index)
+			return 0;
+
+		pad = media_entity_remote_pad(&vidsw->pads[vidsw->active]);
+		if (pad) {
+			struct media_link *link;
+			int ret;
+
+			link = media_entity_find_link(pad,
+						&vidsw->pads[vidsw->active]);
+			if (link) {
+				ret = __media_entity_setup_link(link, 0);
+				if (ret)
+					return ret;
+			}
+		}
+	}
+
+	vidsw_set_active(vidsw, local->index);
+
+	return 0;
+}
+
+static struct media_entity_operations vidsw_ops = {
+	.link_setup = vidsw_link_setup,
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static bool vidsw_endpoint_disabled(struct device_node *ep)
+{
+	struct device_node *rpp;
+
+	if (!of_device_is_available(ep))
+		return true;
+
+	rpp = of_graph_get_remote_port_parent(ep);
+	if (!rpp)
+		return true;
+
+	return !of_device_is_available(rpp);
+}
+
+static int vidsw_async_init(struct vidsw *vidsw, struct device_node *node)
+{
+	struct device_node *ep;
+	u32 portno;
+	int numports;
+	int ret;
+	int i;
+	bool active_link = false;
+
+	numports = vidsw->num_pads;
+
+	for (i = 0; i < numports - 1; i++)
+		vidsw->pads[i].flags = MEDIA_PAD_FL_SINK;
+	vidsw->pads[numports - 1].flags = MEDIA_PAD_FL_SOURCE;
+
+	vidsw->subdev.entity.function = MEDIA_ENT_F_VID_MUX;
+	ret = media_entity_pads_init(&vidsw->subdev.entity, numports,
+				     vidsw->pads);
+	if (ret < 0)
+		return ret;
+
+	vidsw->subdev.entity.ops = &vidsw_ops;
+
+	for_each_endpoint_of_node(node, ep) {
+		struct v4l2_of_endpoint endpoint;
+
+		v4l2_of_parse_endpoint(ep, &endpoint);
+
+		portno = endpoint.base.port;
+		if (portno >= numports - 1)
+			continue;
+
+		if (vidsw_endpoint_disabled(ep)) {
+			dev_dbg(vidsw->subdev.dev,
+				"port %d disabled\n", portno);
+			continue;
+		}
+
+		vidsw->endpoint[portno] = endpoint;
+
+		if (portno == vidsw->active)
+			active_link = true;
+	}
+
+	for (portno = 0; portno < numports - 1; portno++) {
+		if (!vidsw->endpoint[portno].base.local_node)
+			continue;
+
+		/* If the active input is not connected, use another */
+		if (!active_link) {
+			vidsw_set_active(vidsw, portno);
+			active_link = true;
+		}
+	}
+
+	return v4l2_async_register_subdev(&vidsw->subdev);
+}
+
+int vidsw_g_mbus_config(struct v4l2_subdev *sd, struct v4l2_mbus_config *cfg)
+{
+	struct vidsw *vidsw = v4l2_subdev_to_vidsw(sd);
+	struct media_pad *pad;
+	int ret;
+
+	if (vidsw->active == -1) {
+		dev_err(sd->dev, "no configuration for inactive mux\n");
+		return -EINVAL;
+	}
+
+	/*
+	 * Retrieve media bus configuration from the entity connected to the
+	 * active input
+	 */
+	pad = media_entity_remote_pad(&vidsw->pads[vidsw->active]);
+	if (pad) {
+		sd = media_entity_to_v4l2_subdev(pad->entity);
+		ret = v4l2_subdev_call(sd, video, g_mbus_config, cfg);
+		if (ret == -ENOIOCTLCMD)
+			pad = NULL;
+		else if (ret < 0) {
+			dev_err(sd->dev, "failed to get source configuration\n");
+			return ret;
+		}
+	}
+	if (!pad) {
+		/* Mirror the input side on the output side */
+		cfg->type = vidsw->endpoint[vidsw->active].bus_type;
+		if (cfg->type == V4L2_MBUS_PARALLEL ||
+		    cfg->type == V4L2_MBUS_BT656)
+			cfg->flags = vidsw->endpoint[vidsw->active].bus.parallel.flags;
+	}
+
+	return 0;
+}
+
+static int vidsw_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct vidsw *vidsw = v4l2_subdev_to_vidsw(sd);
+	struct v4l2_subdev *upstream_sd;
+	struct media_pad *pad;
+
+	if (vidsw->active == -1) {
+		dev_err(sd->dev, "Can not start streaming on inactive mux\n");
+		return -EINVAL;
+	}
+
+	pad = media_entity_remote_pad(&sd->entity.pads[vidsw->active]);
+	if (!pad) {
+		dev_err(sd->dev, "Failed to find remote source pad\n");
+		return -ENOLINK;
+	}
+
+	if (!is_media_entity_v4l2_subdev(pad->entity)) {
+		dev_err(sd->dev, "Upstream entity is not a v4l2 subdev\n");
+		return -ENODEV;
+	}
+
+	upstream_sd = media_entity_to_v4l2_subdev(pad->entity);
+
+	return v4l2_subdev_call(upstream_sd, video, s_stream, enable);
+}
+
+static int vidsw_g_frame_interval(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_frame_interval *fi)
+{
+	struct vidsw *vidsw = v4l2_subdev_to_vidsw(sd);
+
+	fi->interval = vidsw->timeperframe;
+
+	return 0;
+}
+
+static int vidsw_s_frame_interval(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_frame_interval *fi)
+{
+	struct vidsw *vidsw = v4l2_subdev_to_vidsw(sd);
+
+	/* Output pad mirrors active input pad, no limits on input pads */
+	if (fi->pad == (vidsw->num_pads - 1))
+		fi->interval = vidsw->timeperframe;
+
+	vidsw->timeperframe = fi->interval;
+
+	return 0;
+}
+
+static const struct v4l2_subdev_video_ops vidsw_subdev_video_ops = {
+	.g_mbus_config = vidsw_g_mbus_config,
+	.s_stream = vidsw_s_stream,
+	.g_frame_interval = vidsw_g_frame_interval,
+	.s_frame_interval = vidsw_s_frame_interval,
+};
+
+static struct v4l2_mbus_framefmt *
+__vidsw_get_pad_format(struct v4l2_subdev *sd,
+		       struct v4l2_subdev_pad_config *cfg,
+		       unsigned int pad, u32 which)
+{
+	struct vidsw *vidsw = v4l2_subdev_to_vidsw(sd);
+
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		return v4l2_subdev_get_try_format(sd, cfg, pad);
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		return &vidsw->format_mbus[pad];
+	default:
+		return NULL;
+	}
+}
+
+static int vidsw_get_format(struct v4l2_subdev *sd,
+			    struct v4l2_subdev_pad_config *cfg,
+			    struct v4l2_subdev_format *sdformat)
+{
+	sdformat->format = *__vidsw_get_pad_format(sd, cfg, sdformat->pad,
+						   sdformat->which);
+	return 0;
+}
+
+static int vidsw_set_format(struct v4l2_subdev *sd,
+			    struct v4l2_subdev_pad_config *cfg,
+			    struct v4l2_subdev_format *sdformat)
+{
+	struct vidsw *vidsw = v4l2_subdev_to_vidsw(sd);
+	struct v4l2_mbus_framefmt *mbusformat;
+
+	if (sdformat->pad >= vidsw->num_pads)
+		return -EINVAL;
+
+	mbusformat = __vidsw_get_pad_format(sd, cfg, sdformat->pad,
+					    sdformat->which);
+	if (!mbusformat)
+		return -EINVAL;
+
+	/* Output pad mirrors active input pad, no limitations on input pads */
+	if (sdformat->pad == (vidsw->num_pads - 1) && vidsw->active >= 0)
+		sdformat->format = vidsw->format_mbus[vidsw->active];
+
+	*mbusformat = sdformat->format;
+
+	return 0;
+}
+
+static int vidsw_link_validate(struct v4l2_subdev *sd,
+			       struct media_link *link,
+			       struct v4l2_subdev_format *source_fmt,
+			       struct v4l2_subdev_format *sink_fmt)
+{
+	int ret;
+
+	ret = v4l2_subdev_link_validate_default(sd, link,
+						source_fmt, sink_fmt);
+	if (ret)
+		return ret;
+
+	return v4l2_subdev_link_validate_frame_interval(link);
+}
+
+static struct v4l2_subdev_pad_ops vidsw_pad_ops = {
+	.get_fmt = vidsw_get_format,
+	.set_fmt = vidsw_set_format,
+	.link_validate = vidsw_link_validate,
+};
+
+static struct v4l2_subdev_ops vidsw_subdev_ops = {
+	.pad = &vidsw_pad_ops,
+	.video = &vidsw_subdev_video_ops,
+};
+
+static int of_get_reg_field(struct device_node *node, struct reg_field *field)
+{
+	u32 bit_mask;
+	int ret;
+
+	ret = of_property_read_u32(node, "reg", &field->reg);
+	if (ret < 0)
+		return ret;
+
+	ret = of_property_read_u32(node, "bit-mask", &bit_mask);
+	if (ret < 0)
+		return ret;
+
+	ret = of_property_read_u32(node, "bit-shift", &field->lsb);
+	if (ret < 0)
+		return ret;
+
+	field->msb = field->lsb + fls(bit_mask) - 1;
+
+	return 0;
+}
+
+static int vidsw_probe(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct of_endpoint endpoint;
+	struct device_node *ep;
+	struct reg_field field;
+	struct vidsw *vidsw;
+	struct regmap *map;
+	unsigned int num_pads;
+	int ret;
+
+	vidsw = devm_kzalloc(&pdev->dev, sizeof(*vidsw), GFP_KERNEL);
+	if (!vidsw)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, vidsw);
+
+	v4l2_subdev_init(&vidsw->subdev, &vidsw_subdev_ops);
+	snprintf(vidsw->subdev.name, sizeof(vidsw->subdev.name), "%s",
+			np->name);
+	vidsw->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+	vidsw->subdev.dev = &pdev->dev;
+
+	/* init default frame interval */
+	vidsw->timeperframe.numerator = 1;
+	vidsw->timeperframe.denominator = 30;
+
+	/*
+	 * The largest numbered port is the output port. It determines
+	 * total number of pads
+	 */
+	num_pads = 0;
+	for_each_endpoint_of_node(np, ep) {
+		of_graph_parse_endpoint(ep, &endpoint);
+		num_pads = max(num_pads, endpoint.port + 1);
+	}
+
+	if (num_pads < 2) {
+		dev_err(&pdev->dev, "Not enough ports %d\n", num_pads);
+		return -EINVAL;
+	}
+
+	ret = of_get_reg_field(np, &field);
+	if (ret == 0) {
+		map = syscon_node_to_regmap(np->parent);
+		if (!map) {
+			dev_err(&pdev->dev, "Failed to get syscon register map\n");
+			return PTR_ERR(map);
+		}
+
+		vidsw->field = devm_regmap_field_alloc(&pdev->dev, map, field);
+		if (IS_ERR(vidsw->field)) {
+			dev_err(&pdev->dev, "Failed to allocate regmap field\n");
+			return PTR_ERR(vidsw->field);
+		}
+
+		regmap_field_read(vidsw->field, &vidsw->active);
+	} else {
+		if (num_pads > 3) {
+			dev_err(&pdev->dev, "Too many ports %d\n", num_pads);
+			return -EINVAL;
+		}
+
+		vidsw->gpio = devm_gpiod_get(&pdev->dev, NULL, GPIOD_OUT_LOW);
+		if (IS_ERR(vidsw->gpio)) {
+			dev_warn(&pdev->dev,
+				 "could not request control gpio: %d\n", ret);
+			vidsw->gpio = NULL;
+		}
+
+		vidsw->active = gpiod_get_value(vidsw->gpio) ? 1 : 0;
+	}
+
+	vidsw->num_pads = num_pads;
+	vidsw->pads = devm_kzalloc(&pdev->dev, sizeof(*vidsw->pads) * num_pads,
+			GFP_KERNEL);
+	vidsw->format_mbus = devm_kzalloc(&pdev->dev,
+			sizeof(*vidsw->format_mbus) * num_pads, GFP_KERNEL);
+	vidsw->endpoint = devm_kzalloc(&pdev->dev,
+			sizeof(*vidsw->endpoint) * (num_pads - 1), GFP_KERNEL);
+
+	ret = vidsw_async_init(vidsw, np);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int vidsw_remove(struct platform_device *pdev)
+{
+	struct vidsw *vidsw = platform_get_drvdata(pdev);
+	struct v4l2_subdev *sd = &vidsw->subdev;
+
+	v4l2_async_unregister_subdev(sd);
+	media_entity_cleanup(&sd->entity);
+
+	return 0;
+}
+
+static const struct of_device_id vidsw_dt_ids[] = {
+	{ .compatible = "video-multiplexer", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, vidsw_dt_ids);
+
+static struct platform_driver vidsw_driver = {
+	.probe		= vidsw_probe,
+	.remove		= vidsw_remove,
+	.driver		= {
+		.of_match_table = vidsw_dt_ids,
+		.name = "video-multiplexer",
+	},
+};
+
+module_platform_driver(vidsw_driver);
+
+MODULE_DESCRIPTION("video stream multiplexer");
+MODULE_AUTHOR("Sascha Hauer, Pengutronix");
+MODULE_AUTHOR("Philipp Zabel, Pengutronix");
+MODULE_LICENSE("GPL");
-- 
2.7.4

[PATCH v5 21/39] UAPI: Add media UAPI Kbuild file

[Steve Longerbeam]

Add an empty UAPI Kbuild file for media UAPI headers.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 include/uapi/Kbuild       | 1 +
 include/uapi/media/Kbuild | 1 +
 2 files changed, 2 insertions(+)
 create mode 100644 include/uapi/media/Kbuild

diff --git a/include/uapi/Kbuild b/include/uapi/Kbuild
index 245aa6e..9a51957 100644
--- a/include/uapi/Kbuild
+++ b/include/uapi/Kbuild
@@ -6,6 +6,7 @@
 header-y += asm-generic/
 header-y += linux/
 header-y += sound/
+header-y += media/
 header-y += mtd/
 header-y += rdma/
 header-y += video/
diff --git a/include/uapi/media/Kbuild b/include/uapi/media/Kbuild
new file mode 100644
index 0000000..aafaa5a
--- /dev/null
+++ b/include/uapi/media/Kbuild
@@ -0,0 +1 @@
+# UAPI Header export list
-- 
2.7.4

[PATCH v5 21/39] UAPI: Add media UAPI Kbuild file

[Steve Longerbeam]

Add an empty UAPI Kbuild file for media UAPI headers.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 include/uapi/Kbuild       | 1 +
 include/uapi/media/Kbuild | 1 +
 2 files changed, 2 insertions(+)
 create mode 100644 include/uapi/media/Kbuild

diff --git a/include/uapi/Kbuild b/include/uapi/Kbuild
index 245aa6e..9a51957 100644
--- a/include/uapi/Kbuild
+++ b/include/uapi/Kbuild
@@ -6,6 +6,7 @@
 header-y += asm-generic/
 header-y += linux/
 header-y += sound/
+header-y += media/
 header-y += mtd/
 header-y += rdma/
 header-y += video/
diff --git a/include/uapi/media/Kbuild b/include/uapi/media/Kbuild
new file mode 100644
index 0000000..aafaa5a
--- /dev/null
+++ b/include/uapi/media/Kbuild
@@ -0,0 +1 @@
+# UAPI Header export list
-- 
2.7.4

[PATCH v5 21/39] UAPI: Add media UAPI Kbuild file

[Steve Longerbeam]

Add an empty UAPI Kbuild file for media UAPI headers.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 include/uapi/Kbuild       | 1 +
 include/uapi/media/Kbuild | 1 +
 2 files changed, 2 insertions(+)
 create mode 100644 include/uapi/media/Kbuild

diff --git a/include/uapi/Kbuild b/include/uapi/Kbuild
index 245aa6e..9a51957 100644
--- a/include/uapi/Kbuild
+++ b/include/uapi/Kbuild
@@ -6,6 +6,7 @@
 header-y += asm-generic/
 header-y += linux/
 header-y += sound/
+header-y += media/
 header-y += mtd/
 header-y += rdma/
 header-y += video/
diff --git a/include/uapi/media/Kbuild b/include/uapi/media/Kbuild
new file mode 100644
index 0000000..aafaa5a
--- /dev/null
+++ b/include/uapi/media/Kbuild
@@ -0,0 +1 @@
+# UAPI Header export list
-- 
2.7.4

Re: [PATCH v5 21/39] UAPI: Add media UAPI Kbuild file

[Sakari Ailus]

Hi Steve,

On Thu, Mar 09, 2017 at 08:53:01PM -0800, Steve Longerbeam wrote:
> Add an empty UAPI Kbuild file for media UAPI headers.
> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>

The existing V4L2 UAPI headers are under include/uapi/linux. Could you use
that directory instead?

I actually wouldn't really object doing this but it should have been done in
2002 or so when the first V4L2 header was added. Now the benefit is
questionable.

-- 
Sakari Ailus
e-mail: sakari.ailus@iki.fi	XMPP: sailus@retiisi.org.uk

[PATCH v5 21/39] UAPI: Add media UAPI Kbuild file

[Sakari Ailus]

Hi Steve,

On Thu, Mar 09, 2017 at 08:53:01PM -0800, Steve Longerbeam wrote:
> Add an empty UAPI Kbuild file for media UAPI headers.
> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>

The existing V4L2 UAPI headers are under include/uapi/linux. Could you use
that directory instead?

I actually wouldn't really object doing this but it should have been done in
2002 or so when the first V4L2 header was added. Now the benefit is
questionable.

-- 
Sakari Ailus
e-mail: sakari.ailus at iki.fi	XMPP: sailus at retiisi.org.uk

Re: [PATCH v5 21/39] UAPI: Add media UAPI Kbuild file

[Sakari Ailus]

Hi Steve,

On Thu, Mar 09, 2017 at 08:53:01PM -0800, Steve Longerbeam wrote:
> Add an empty UAPI Kbuild file for media UAPI headers.
> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam-nmGgyN9QBj3QT0dZR+AlfA@public.gmane.org>

The existing V4L2 UAPI headers are under include/uapi/linux. Could you use
that directory instead?

I actually wouldn't really object doing this but it should have been done in
2002 or so when the first V4L2 header was added. Now the benefit is
questionable.

-- 
Sakari Ailus
e-mail: sakari.ailus-X3B1VOXEql0@public.gmane.org	XMPP: sailus-PCDdDYkjdNMDXYZnReoRVg@public.gmane.org
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 21/39] UAPI: Add media UAPI Kbuild file

[Steve Longerbeam]

On 03/11/2017 05:49 AM, Sakari Ailus wrote:
> Hi Steve,
>
> On Thu, Mar 09, 2017 at 08:53:01PM -0800, Steve Longerbeam wrote:
>> Add an empty UAPI Kbuild file for media UAPI headers.
>>
>> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
>
> The existing V4L2 UAPI headers are under include/uapi/linux. Could you use
> that directory instead?
>
> I actually wouldn't really object doing this but it should have been done in
> 2002 or so when the first V4L2 header was added. Now the benefit is
> questionable.
>

Agreed, I think the current headers should be moved to uapi/media
eventually, but for now I'll go ahead and put under uapi/linux.

Steve

[PATCH v5 21/39] UAPI: Add media UAPI Kbuild file

[Steve Longerbeam]

On 03/11/2017 05:49 AM, Sakari Ailus wrote:
> Hi Steve,
>
> On Thu, Mar 09, 2017 at 08:53:01PM -0800, Steve Longerbeam wrote:
>> Add an empty UAPI Kbuild file for media UAPI headers.
>>
>> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
>
> The existing V4L2 UAPI headers are under include/uapi/linux. Could you use
> that directory instead?
>
> I actually wouldn't really object doing this but it should have been done in
> 2002 or so when the first V4L2 header was added. Now the benefit is
> questionable.
>

Agreed, I think the current headers should be moved to uapi/media
eventually, but for now I'll go ahead and put under uapi/linux.

Steve

Re: [PATCH v5 21/39] UAPI: Add media UAPI Kbuild file

[Steve Longerbeam]

On 03/11/2017 05:49 AM, Sakari Ailus wrote:
> Hi Steve,
>
> On Thu, Mar 09, 2017 at 08:53:01PM -0800, Steve Longerbeam wrote:
>> Add an empty UAPI Kbuild file for media UAPI headers.
>>
>> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
>
> The existing V4L2 UAPI headers are under include/uapi/linux. Could you use
> that directory instead?
>
> I actually wouldn't really object doing this but it should have been done in
> 2002 or so when the first V4L2 header was added. Now the benefit is
> questionable.
>

Agreed, I think the current headers should be moved to uapi/media
eventually, but for now I'll go ahead and put under uapi/linux.

Steve

Re: [PATCH v5 21/39] UAPI: Add media UAPI Kbuild file

[Hans Verkuil]

On 03/11/2017 07:20 PM, Steve Longerbeam wrote:
> 
> 
> On 03/11/2017 05:49 AM, Sakari Ailus wrote:
>> Hi Steve,
>>
>> On Thu, Mar 09, 2017 at 08:53:01PM -0800, Steve Longerbeam wrote:
>>> Add an empty UAPI Kbuild file for media UAPI headers.
>>>
>>> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
>>
>> The existing V4L2 UAPI headers are under include/uapi/linux. Could you use
>> that directory instead?
>>
>> I actually wouldn't really object doing this but it should have been done in
>> 2002 or so when the first V4L2 header was added. Now the benefit is
>> questionable.
>>
> 
> Agreed, I think the current headers should be moved to uapi/media
> eventually, but for now I'll go ahead and put under uapi/linux.

No, while in staging it shouldn't be exported.

Put it in include/linux and move it to uapi when this driver is mainlined.

I don't think we can move headers from uapi/linux to uapi/media, I'm sure it's
too late for that.

Regards,

	Hans

[PATCH v5 21/39] UAPI: Add media UAPI Kbuild file

[Hans Verkuil]

On 03/11/2017 07:20 PM, Steve Longerbeam wrote:
> 
> 
> On 03/11/2017 05:49 AM, Sakari Ailus wrote:
>> Hi Steve,
>>
>> On Thu, Mar 09, 2017 at 08:53:01PM -0800, Steve Longerbeam wrote:
>>> Add an empty UAPI Kbuild file for media UAPI headers.
>>>
>>> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
>>
>> The existing V4L2 UAPI headers are under include/uapi/linux. Could you use
>> that directory instead?
>>
>> I actually wouldn't really object doing this but it should have been done in
>> 2002 or so when the first V4L2 header was added. Now the benefit is
>> questionable.
>>
> 
> Agreed, I think the current headers should be moved to uapi/media
> eventually, but for now I'll go ahead and put under uapi/linux.

No, while in staging it shouldn't be exported.

Put it in include/linux and move it to uapi when this driver is mainlined.

I don't think we can move headers from uapi/linux to uapi/media, I'm sure it's
too late for that.

Regards,

	Hans

Re: [PATCH v5 21/39] UAPI: Add media UAPI Kbuild file

[Hans Verkuil]

On 03/11/2017 07:20 PM, Steve Longerbeam wrote:
> 
> 
> On 03/11/2017 05:49 AM, Sakari Ailus wrote:
>> Hi Steve,
>>
>> On Thu, Mar 09, 2017 at 08:53:01PM -0800, Steve Longerbeam wrote:
>>> Add an empty UAPI Kbuild file for media UAPI headers.
>>>
>>> Signed-off-by: Steve Longerbeam <steve_longerbeam-nmGgyN9QBj3QT0dZR+AlfA@public.gmane.org>
>>
>> The existing V4L2 UAPI headers are under include/uapi/linux. Could you use
>> that directory instead?
>>
>> I actually wouldn't really object doing this but it should have been done in
>> 2002 or so when the first V4L2 header was added. Now the benefit is
>> questionable.
>>
> 
> Agreed, I think the current headers should be moved to uapi/media
> eventually, but for now I'll go ahead and put under uapi/linux.

No, while in staging it shouldn't be exported.

Put it in include/linux and move it to uapi when this driver is mainlined.

I don't think we can move headers from uapi/linux to uapi/media, I'm sure it's
too late for that.

Regards,

	Hans

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v5 22/39] media: Add userspace header file for i.MX

[Steve Longerbeam]

This adds a header file for use by userspace programs wanting to interact
with the i.MX media driver. It defines custom v4l2 controls for the
i.MX v4l2 subdevices.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 include/uapi/media/Kbuild |  1 +
 include/uapi/media/imx.h  | 21 +++++++++++++++++++++
 2 files changed, 22 insertions(+)
 create mode 100644 include/uapi/media/imx.h

diff --git a/include/uapi/media/Kbuild b/include/uapi/media/Kbuild
index aafaa5a..fa78958 100644
--- a/include/uapi/media/Kbuild
+++ b/include/uapi/media/Kbuild
@@ -1 +1,2 @@
 # UAPI Header export list
+header-y += imx.h
diff --git a/include/uapi/media/imx.h b/include/uapi/media/imx.h
new file mode 100644
index 0000000..f573de4
--- /dev/null
+++ b/include/uapi/media/imx.h
@@ -0,0 +1,21 @@
+/*
+ * Copyright (c) 2014-2015 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version
+ */
+
+#ifndef __UAPI_MEDIA_IMX_H__
+#define __UAPI_MEDIA_IMX_H__
+
+enum imx_ctrl_id {
+	V4L2_CID_IMX_FIM_ENABLE = (V4L2_CID_USER_IMX_BASE + 0),
+	V4L2_CID_IMX_FIM_NUM,
+	V4L2_CID_IMX_FIM_TOLERANCE_MIN,
+	V4L2_CID_IMX_FIM_TOLERANCE_MAX,
+	V4L2_CID_IMX_FIM_NUM_SKIP,
+};
+
+#endif
-- 
2.7.4

[PATCH v5 22/39] media: Add userspace header file for i.MX

[Steve Longerbeam]

This adds a header file for use by userspace programs wanting to interact
with the i.MX media driver. It defines custom v4l2 controls for the
i.MX v4l2 subdevices.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 include/uapi/media/Kbuild |  1 +
 include/uapi/media/imx.h  | 21 +++++++++++++++++++++
 2 files changed, 22 insertions(+)
 create mode 100644 include/uapi/media/imx.h

diff --git a/include/uapi/media/Kbuild b/include/uapi/media/Kbuild
index aafaa5a..fa78958 100644
--- a/include/uapi/media/Kbuild
+++ b/include/uapi/media/Kbuild
@@ -1 +1,2 @@
 # UAPI Header export list
+header-y += imx.h
diff --git a/include/uapi/media/imx.h b/include/uapi/media/imx.h
new file mode 100644
index 0000000..f573de4
--- /dev/null
+++ b/include/uapi/media/imx.h
@@ -0,0 +1,21 @@
+/*
+ * Copyright (c) 2014-2015 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version
+ */
+
+#ifndef __UAPI_MEDIA_IMX_H__
+#define __UAPI_MEDIA_IMX_H__
+
+enum imx_ctrl_id {
+	V4L2_CID_IMX_FIM_ENABLE = (V4L2_CID_USER_IMX_BASE + 0),
+	V4L2_CID_IMX_FIM_NUM,
+	V4L2_CID_IMX_FIM_TOLERANCE_MIN,
+	V4L2_CID_IMX_FIM_TOLERANCE_MAX,
+	V4L2_CID_IMX_FIM_NUM_SKIP,
+};
+
+#endif
-- 
2.7.4

[PATCH v5 22/39] media: Add userspace header file for i.MX

[Steve Longerbeam]

This adds a header file for use by userspace programs wanting to interact
with the i.MX media driver. It defines custom v4l2 controls for the
i.MX v4l2 subdevices.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 include/uapi/media/Kbuild |  1 +
 include/uapi/media/imx.h  | 21 +++++++++++++++++++++
 2 files changed, 22 insertions(+)
 create mode 100644 include/uapi/media/imx.h

diff --git a/include/uapi/media/Kbuild b/include/uapi/media/Kbuild
index aafaa5a..fa78958 100644
--- a/include/uapi/media/Kbuild
+++ b/include/uapi/media/Kbuild
@@ -1 +1,2 @@
 # UAPI Header export list
+header-y += imx.h
diff --git a/include/uapi/media/imx.h b/include/uapi/media/imx.h
new file mode 100644
index 0000000..f573de4
--- /dev/null
+++ b/include/uapi/media/imx.h
@@ -0,0 +1,21 @@
+/*
+ * Copyright (c) 2014-2015 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version
+ */
+
+#ifndef __UAPI_MEDIA_IMX_H__
+#define __UAPI_MEDIA_IMX_H__
+
+enum imx_ctrl_id {
+	V4L2_CID_IMX_FIM_ENABLE = (V4L2_CID_USER_IMX_BASE + 0),
+	V4L2_CID_IMX_FIM_NUM,
+	V4L2_CID_IMX_FIM_TOLERANCE_MIN,
+	V4L2_CID_IMX_FIM_TOLERANCE_MAX,
+	V4L2_CID_IMX_FIM_NUM_SKIP,
+};
+
+#endif
-- 
2.7.4

Re: [PATCH v5 22/39] media: Add userspace header file for i.MX

[Hans Verkuil]

On 10/03/17 05:53, Steve Longerbeam wrote:
> This adds a header file for use by userspace programs wanting to interact
> with the i.MX media driver. It defines custom v4l2 controls for the
> i.MX v4l2 subdevices.
> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>

I would not export this while the imx driver is in staging.

Also, traditionally exported media headers are in linux, not media.

I would like to have a discussion about that before deciding where to
place this header.

For the record: I am not opposed to placing this in media.

Regards,

	Hans

> ---
>  include/uapi/media/Kbuild |  1 +
>  include/uapi/media/imx.h  | 21 +++++++++++++++++++++
>  2 files changed, 22 insertions(+)
>  create mode 100644 include/uapi/media/imx.h
> 
> diff --git a/include/uapi/media/Kbuild b/include/uapi/media/Kbuild
> index aafaa5a..fa78958 100644
> --- a/include/uapi/media/Kbuild
> +++ b/include/uapi/media/Kbuild
> @@ -1 +1,2 @@
>  # UAPI Header export list
> +header-y += imx.h
> diff --git a/include/uapi/media/imx.h b/include/uapi/media/imx.h
> new file mode 100644
> index 0000000..f573de4
> --- /dev/null
> +++ b/include/uapi/media/imx.h
> @@ -0,0 +1,21 @@
> +/*
> + * Copyright (c) 2014-2015 Mentor Graphics Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by the
> + * Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version
> + */
> +
> +#ifndef __UAPI_MEDIA_IMX_H__
> +#define __UAPI_MEDIA_IMX_H__
> +
> +enum imx_ctrl_id {
> +	V4L2_CID_IMX_FIM_ENABLE = (V4L2_CID_USER_IMX_BASE + 0),
> +	V4L2_CID_IMX_FIM_NUM,
> +	V4L2_CID_IMX_FIM_TOLERANCE_MIN,
> +	V4L2_CID_IMX_FIM_TOLERANCE_MAX,
> +	V4L2_CID_IMX_FIM_NUM_SKIP,
> +};
> +
> +#endif
> 

[PATCH v5 22/39] media: Add userspace header file for i.MX

[Hans Verkuil]

On 10/03/17 05:53, Steve Longerbeam wrote:
> This adds a header file for use by userspace programs wanting to interact
> with the i.MX media driver. It defines custom v4l2 controls for the
> i.MX v4l2 subdevices.
> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>

I would not export this while the imx driver is in staging.

Also, traditionally exported media headers are in linux, not media.

I would like to have a discussion about that before deciding where to
place this header.

For the record: I am not opposed to placing this in media.

Regards,

	Hans

> ---
>  include/uapi/media/Kbuild |  1 +
>  include/uapi/media/imx.h  | 21 +++++++++++++++++++++
>  2 files changed, 22 insertions(+)
>  create mode 100644 include/uapi/media/imx.h
> 
> diff --git a/include/uapi/media/Kbuild b/include/uapi/media/Kbuild
> index aafaa5a..fa78958 100644
> --- a/include/uapi/media/Kbuild
> +++ b/include/uapi/media/Kbuild
> @@ -1 +1,2 @@
>  # UAPI Header export list
> +header-y += imx.h
> diff --git a/include/uapi/media/imx.h b/include/uapi/media/imx.h
> new file mode 100644
> index 0000000..f573de4
> --- /dev/null
> +++ b/include/uapi/media/imx.h
> @@ -0,0 +1,21 @@
> +/*
> + * Copyright (c) 2014-2015 Mentor Graphics Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by the
> + * Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version
> + */
> +
> +#ifndef __UAPI_MEDIA_IMX_H__
> +#define __UAPI_MEDIA_IMX_H__
> +
> +enum imx_ctrl_id {
> +	V4L2_CID_IMX_FIM_ENABLE = (V4L2_CID_USER_IMX_BASE + 0),
> +	V4L2_CID_IMX_FIM_NUM,
> +	V4L2_CID_IMX_FIM_TOLERANCE_MIN,
> +	V4L2_CID_IMX_FIM_TOLERANCE_MAX,
> +	V4L2_CID_IMX_FIM_NUM_SKIP,
> +};
> +
> +#endif
> 

Re: [PATCH v5 22/39] media: Add userspace header file for i.MX

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 1393 bytes --]

Hi!

> diff --git a/include/uapi/media/Kbuild b/include/uapi/media/Kbuild
> index aafaa5a..fa78958 100644
> --- a/include/uapi/media/Kbuild
> +++ b/include/uapi/media/Kbuild
> @@ -1 +1,2 @@
>  # UAPI Header export list
> +header-y += imx.h
> diff --git a/include/uapi/media/imx.h b/include/uapi/media/imx.h
> new file mode 100644
> index 0000000..f573de4
> --- /dev/null
> +++ b/include/uapi/media/imx.h
> @@ -0,0 +1,21 @@
> +/*
> + * Copyright (c) 2014-2015 Mentor Graphics Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by the
> + * Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version
> + */
> +
> +#ifndef __UAPI_MEDIA_IMX_H__
> +#define __UAPI_MEDIA_IMX_H__
> +
> +enum imx_ctrl_id {
> +	V4L2_CID_IMX_FIM_ENABLE = (V4L2_CID_USER_IMX_BASE + 0),
> +	V4L2_CID_IMX_FIM_NUM,
> +	V4L2_CID_IMX_FIM_TOLERANCE_MIN,
> +	V4L2_CID_IMX_FIM_TOLERANCE_MAX,
> +	V4L2_CID_IMX_FIM_NUM_SKIP,
> +};
> +

Should this #include something so that if userland includes it, it
will not get compile error?

Should there be some documentation of userland API?
									Pavel
-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

[PATCH v5 22/39] media: Add userspace header file for i.MX

[Pavel Machek]

Hi!

> diff --git a/include/uapi/media/Kbuild b/include/uapi/media/Kbuild
> index aafaa5a..fa78958 100644
> --- a/include/uapi/media/Kbuild
> +++ b/include/uapi/media/Kbuild
> @@ -1 +1,2 @@
>  # UAPI Header export list
> +header-y += imx.h
> diff --git a/include/uapi/media/imx.h b/include/uapi/media/imx.h
> new file mode 100644
> index 0000000..f573de4
> --- /dev/null
> +++ b/include/uapi/media/imx.h
> @@ -0,0 +1,21 @@
> +/*
> + * Copyright (c) 2014-2015 Mentor Graphics Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by the
> + * Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version
> + */
> +
> +#ifndef __UAPI_MEDIA_IMX_H__
> +#define __UAPI_MEDIA_IMX_H__
> +
> +enum imx_ctrl_id {
> +	V4L2_CID_IMX_FIM_ENABLE = (V4L2_CID_USER_IMX_BASE + 0),
> +	V4L2_CID_IMX_FIM_NUM,
> +	V4L2_CID_IMX_FIM_TOLERANCE_MIN,
> +	V4L2_CID_IMX_FIM_TOLERANCE_MAX,
> +	V4L2_CID_IMX_FIM_NUM_SKIP,
> +};
> +

Should this #include something so that if userland includes it, it
will not get compile error?

Should there be some documentation of userland API?
									Pavel
-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 181 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170311/fc0feec7/attachment.sig>

Re: [PATCH v5 22/39] media: Add userspace header file for i.MX

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 1393 bytes --]

Hi!

> diff --git a/include/uapi/media/Kbuild b/include/uapi/media/Kbuild
> index aafaa5a..fa78958 100644
> --- a/include/uapi/media/Kbuild
> +++ b/include/uapi/media/Kbuild
> @@ -1 +1,2 @@
>  # UAPI Header export list
> +header-y += imx.h
> diff --git a/include/uapi/media/imx.h b/include/uapi/media/imx.h
> new file mode 100644
> index 0000000..f573de4
> --- /dev/null
> +++ b/include/uapi/media/imx.h
> @@ -0,0 +1,21 @@
> +/*
> + * Copyright (c) 2014-2015 Mentor Graphics Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by the
> + * Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version
> + */
> +
> +#ifndef __UAPI_MEDIA_IMX_H__
> +#define __UAPI_MEDIA_IMX_H__
> +
> +enum imx_ctrl_id {
> +	V4L2_CID_IMX_FIM_ENABLE = (V4L2_CID_USER_IMX_BASE + 0),
> +	V4L2_CID_IMX_FIM_NUM,
> +	V4L2_CID_IMX_FIM_TOLERANCE_MIN,
> +	V4L2_CID_IMX_FIM_TOLERANCE_MAX,
> +	V4L2_CID_IMX_FIM_NUM_SKIP,
> +};
> +

Should this #include something so that if userland includes it, it
will not get compile error?

Should there be some documentation of userland API?
									Pavel
-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

[PATCH v5 23/39] media: Add i.MX media core driver

[Steve Longerbeam]

Add the core media driver for i.MX SOC.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 Documentation/media/v4l-drivers/imx.rst           | 560 ++++++++++++++++
 drivers/staging/media/Kconfig                     |   2 +
 drivers/staging/media/Makefile                    |   1 +
 drivers/staging/media/imx/Kconfig                 |   6 +
 drivers/staging/media/imx/Makefile                |   5 +
 drivers/staging/media/imx/TODO                    |  17 +
 drivers/staging/media/imx/imx-media-dev.c         | 522 +++++++++++++++
 drivers/staging/media/imx/imx-media-fim.c         | 471 +++++++++++++
 drivers/staging/media/imx/imx-media-internal-sd.c | 349 ++++++++++
 drivers/staging/media/imx/imx-media-of.c          | 267 ++++++++
 drivers/staging/media/imx/imx-media-utils.c       | 766 ++++++++++++++++++++++
 drivers/staging/media/imx/imx-media.h             | 303 +++++++++
 include/media/imx.h                               |  15 +
 include/uapi/linux/v4l2-controls.h                |   4 +
 14 files changed, 3288 insertions(+)
 create mode 100644 Documentation/media/v4l-drivers/imx.rst
 create mode 100644 drivers/staging/media/imx/Kconfig
 create mode 100644 drivers/staging/media/imx/Makefile
 create mode 100644 drivers/staging/media/imx/TODO
 create mode 100644 drivers/staging/media/imx/imx-media-dev.c
 create mode 100644 drivers/staging/media/imx/imx-media-fim.c
 create mode 100644 drivers/staging/media/imx/imx-media-internal-sd.c
 create mode 100644 drivers/staging/media/imx/imx-media-of.c
 create mode 100644 drivers/staging/media/imx/imx-media-utils.c
 create mode 100644 drivers/staging/media/imx/imx-media.h
 create mode 100644 include/media/imx.h

diff --git a/Documentation/media/v4l-drivers/imx.rst b/Documentation/media/v4l-drivers/imx.rst
new file mode 100644
index 0000000..443e0d0
--- /dev/null
+++ b/Documentation/media/v4l-drivers/imx.rst
@@ -0,0 +1,560 @@
+i.MX Video Capture Driver
+=========================
+
+Introduction
+------------
+
+The Freescale i.MX5/6 contains an Image Processing Unit (IPU), which
+handles the flow of image frames to and from capture devices and
+display devices.
+
+For image capture, the IPU contains the following internal subunits:
+
+- Image DMA Controller (IDMAC)
+- Camera Serial Interface (CSI)
+- Image Converter (IC)
+- Sensor Multi-FIFO Controller (SMFC)
+- Image Rotator (IRT)
+- Video De-Interlacing or Combining Block (VDIC)
+
+The IDMAC is the DMA controller for transfer of image frames to and from
+memory. Various dedicated DMA channels exist for both video capture and
+display paths. During transfer, the IDMAC is also capable of vertical
+image flip, 8x8 block transfer (see IRT description), pixel component
+re-ordering (for example UYVY to YUYV) within the same colorspace, and
+even packed <--> planar conversion. It can also perform a simple
+de-interlacing by interleaving even and odd lines during transfer
+(without motion compensation which requires the VDIC).
+
+The CSI is the backend capture unit that interfaces directly with
+camera sensors over Parallel, BT.656/1120, and MIPI CSI-2 busses.
+
+The IC handles color-space conversion, resizing (downscaling and
+upscaling), horizontal flip, and 90/270 degree rotation operations.
+
+There are three independent "tasks" within the IC that can carry out
+conversions concurrently: pre-process encoding, pre-process viewfinder,
+and post-processing. Within each task, conversions are split into three
+sections: downsizing section, main section (upsizing, flip, colorspace
+conversion, and graphics plane combining), and rotation section.
+
+The IPU time-shares the IC task operations. The time-slice granularity
+is one burst of eight pixels in the downsizing section, one image line
+in the main processing section, one image frame in the rotation section.
+
+The SMFC is composed of four independent FIFOs that each can transfer
+captured frames from sensors directly to memory concurrently via four
+IDMAC channels.
+
+The IRT carries out 90 and 270 degree image rotation operations. The
+rotation operation is carried out on 8x8 pixel blocks at a time. This
+operation is supported by the IDMAC which handles the 8x8 block transfer
+along with block reordering, in coordination with vertical flip.
+
+The VDIC handles the conversion of interlaced video to progressive, with
+support for different motion compensation modes (low, medium, and high
+motion). The deinterlaced output frames from the VDIC can be sent to the
+IC pre-process viewfinder task for further conversions. The VDIC also
+contains a Combiner that combines two image planes, with alpha blending
+and color keying.
+
+In addition to the IPU internal subunits, there are also two units
+outside the IPU that are also involved in video capture on i.MX:
+
+- MIPI CSI-2 Receiver for camera sensors with the MIPI CSI-2 bus
+  interface. This is a Synopsys DesignWare core.
+- Two video multiplexers for selecting among multiple sensor inputs
+  to send to a CSI.
+
+For more info, refer to the latest versions of the i.MX5/6 reference
+manuals listed under References.
+
+
+Features
+--------
+
+Some of the features of this driver include:
+
+- Many different pipelines can be configured via media controller API,
+  that correspond to the hardware video capture pipelines supported in
+  the i.MX.
+
+- Supports parallel, BT.565, and MIPI CSI-2 interfaces.
+
+- Up to four concurrent sensor acquisitions, by configuring each
+  sensor's pipeline using independent entities. This is currently
+  demonstrated with the SabreSD and SabreLite reference boards with
+  independent OV5642 and MIPI CSI-2 OV5640 sensor modules.
+
+- Scaling, color-space conversion, horizontal and vertical flip, and
+  image rotation via IC task subdevs.
+
+- Many pixel formats supported (RGB, packed and planar YUV, partial
+  planar YUV).
+
+- The VDIC subdev supports motion compensated de-interlacing, with three
+  motion compensation modes: low, medium, and high motion. Pipelines are
+  defined that allow sending frames to the VDIC subdev directly from the
+  CSI or from memory buffers via an output/mem2mem device node. For low
+  and medium motion modes, the VDIC must receive from memory buffers via
+  a device node.
+
+- Includes a Frame Interval Monitor (FIM) that can correct vertical sync
+  problems with the ADV718x video decoders. See below for a description
+  of the FIM.
+
+
+Entities
+--------
+
+imx6-mipi-csi2
+--------------
+
+This is the MIPI CSI-2 receiver entity. It has one sink pad to receive
+the MIPI CSI-2 stream (usually from a MIPI CSI-2 camera sensor). It has
+four source pads, corresponding to the four MIPI CSI-2 demuxed virtual
+channel outputs.
+
+This entity actually consists of two sub-blocks. One is the MIPI CSI-2
+core. This is a Synopsys Designware MIPI CSI-2 core. The other sub-block
+is a "CSI-2 to IPU gasket". The gasket acts as a demultiplexer of the
+four virtual channels streams, providing four separate parallel buses
+containing each virtual channel that are routed to CSIs or video
+multiplexers as described below.
+
+On i.MX6 solo/dual-lite, all four virtual channel buses are routed to
+two video multiplexers. Both CSI0 and CSI1 can receive any virtual
+channel, as selected by the video multiplexers.
+
+On i.MX6 Quad, virtual channel 0 is routed to IPU1-CSI0 (after selected
+by a video mux), virtual channels 1 and 2 are hard-wired to IPU1-CSI1
+and IPU2-CSI0, respectively, and virtual channel 3 is routed to
+IPU2-CSI1 (again selected by a video mux).
+
+ipuX_csiY_mux
+-------------
+
+These are the video multiplexers. They have two or more sink pads to
+select from either camera sensors with a parallel interface, or from
+MIPI CSI-2 virtual channels from imx6-mipi-csi2 entity. They have a
+single source pad that routes to a CSI (ipuX_csiY entities).
+
+On i.MX6 solo/dual-lite, there are two video mux entities. One sits
+in front of IPU1-CSI0 to select between a parallel sensor and any of
+the four MIPI CSI-2 virtual channels (a total of five sink pads). The
+other mux sits in front of IPU1-CSI1, and again has five sink pads to
+select between a parallel sensor and any of the four MIPI CSI-2 virtual
+channels.
+
+On i.MX6 Quad, there are two video mux entities. One sits in front of
+IPU1-CSI0 to select between a parallel sensor and MIPI CSI-2 virtual
+channel 0 (two sink pads). The other mux sits in front of IPU2-CSI1 to
+select between a parallel sensor and MIPI CSI-2 virtual channel 3 (two
+sink pads).
+
+ipuX_csiY
+---------
+
+These are the CSI entities. They have a single sink pad receiving from
+either a video mux or from a MIPI CSI-2 virtual channel as described
+above.
+
+This entity has two source pads. The first source pad can link directly
+to the ipuX_vdic entity or the ipuX_ic_prp entity, using hardware links
+that require no IDMAC memory buffer transfer.
+
+When the direct source pad is routed to the ipuX_ic_prp entity, frames
+from the CSI will be processed by one of the IC pre-processing tasks.
+
+When the direct source pad is routed to the ipuX_vdic entity, the VDIC
+will carry out motion-compensated de-interlace using "high motion" mode
+(see description of ipuX_vdic entity).
+
+The second source pad sends video frames to memory buffers via the SMFC
+and an IDMAC channel. This source pad is routed to a capture device
+node.
+
+Note that since the IDMAC source pad makes use of an IDMAC channel, it
+can do pixel reordering within the same colorspace. For example, the
+sink pad can take UYVY2X8, but the IDMAC source pad can output YUYV2X8.
+If the sink pad is receiving YUV, the output at the capture device can
+also be converted to a planar YUV format such as YUV420.
+
+It will also perform simple de-interlace without motion compensation,
+which is activated if the sink pad's field type is an interlaced type,
+and the IDMAC source pad field type is set to none.
+
+This subdev can generate two types of events:
+
+- V4L2_EVENT_NEW_FRAME_BEFORE_EOF
+- V4L2_EVENT_FRAME_INTERVAL_ERROR
+
+The user application can subscribe to these events from the ipuX_csiY
+subdev node. The V4L2_EVENT_FRAME_INTERVAL_ERROR event is generated
+by the Frame Interval Monitor (see below for more on the FIM).
+
+ipuX_vdic
+---------
+
+The VDIC carries out motion compensated de-interlacing, with three
+motion compensation modes: low, medium, and high motion. The mode is
+specified with the menu control V4L2_CID_DEINTERLACING_MODE. It has
+two sink pads and a single source pad.
+
+The direct sink pad receives from an ipuX_csiY direct pad. With this
+link the VDIC can only operate in high motion mode.
+
+When the IDMAC sink pad is activated, it receives from an output
+or mem2mem device node. With this pipeline, it can also operate
+in low and medium modes, because these modes require receiving
+frames from memory buffers. Note that an output or mem2mem device
+is not implemented yet, so this sink pad currently has no links.
+
+The source pad routes to the IC pre-processing entity ipuX_ic_prp.
+
+ipuX_ic_prp
+-----------
+
+This is the IC pre-processing entity. It acts as a router, routing
+data from its sink pad to one or both of its source pads.
+
+It has a single sink pad. The sink pad can receive from the ipuX_csiY
+direct pad, or from ipuX_vdic.
+
+This entity has two source pads. One source pad routes to the
+pre-process encode task entity (ipuX_ic_prpenc), the other to the
+pre-process viewfinder task entity (ipuX_ic_prpvf). Both source pads
+can be activated at the same time if the sink pad is receiving from
+ipuX_csiY. Only the source pad to the pre-process viewfinder task entity
+can be activated if the sink pad is receiving from ipuX_vdic (frames
+from the VDIC can only be processed by the pre-process viewfinder task).
+
+ipuX_ic_prpenc
+--------------
+
+This is the IC pre-processing encode entity. It has a single sink pad
+from ipuX_ic_prp, and a single source pad. The source pad is routed
+to a capture device node.
+
+This entity performs the IC pre-process encode task operations:
+color-space conversion, resizing (downscaling and upscaling), horizontal
+and vertical flip, and 90/270 degree rotation.
+
+Like the ipuX_csiY IDMAC source, it can also perform simple de-interlace
+without motion compensation, and pixel reordering.
+
+This subdev can generate the V4L2_EVENT_NEW_FRAME_BEFORE_EOF event, and
+can be subscribed to from the ipuX_ic_prpenc subdev node.
+
+ipuX_ic_prpvf
+-------------
+
+This is the IC pre-processing viewfinder entity. It has a single sink pad
+from ipuX_ic_prp, and a single source pad. The source pad is routed to
+a capture device node.
+
+It is identical in operation to ipuX_ic_prpenc. It will receive and
+process de-interlaced frames from the ipuX_vdic if ipuX_ic_prp is
+receiving from ipuX_vdic.
+
+Like the ipuX_csiY IDMAC source, it can perform simple de-interlace
+without motion compensation. However, note that if the ipuX_vdic is
+included in the pipeline (ipuX_ic_prp is receiving from ipuX_vdic),
+it's not possible to use simple de-interlace in ipuX_ic_prpvf, since
+the ipuX_vdic has already carried out de-interlacing (with motion
+compensation) and therefore the field type output from ipuX_ic_prp can
+only be none.
+
+This subdev can generate the V4L2_EVENT_NEW_FRAME_BEFORE_EOF event, and
+can be subscribed to from the ipuX_ic_prpvf subdev node.
+
+Capture Pipelines
+-----------------
+
+The following describe the various use-cases supported by the pipelines.
+
+The links shown do not include the backend sensor, video mux, or mipi
+csi-2 receiver links. This depends on the type of sensor interface
+(parallel or mipi csi-2). So in all cases, these pipelines begin with:
+
+sensor -> ipuX_csiY_mux -> ...
+
+for parallel sensors, or:
+
+sensor -> imx6-mipi-csi2 -> (ipuX_csiY_mux) -> ...
+
+for mipi csi-2 sensors. The imx6-mipi-csi2 receiver may need to route
+to the video mux (ipuX_csiY_mux) before sending to the CSI, depending
+on the mipi csi-2 virtual channel, hence ipuX_csiY_mux is shown in
+parenthesis.
+
+Unprocessed Video Capture:
+--------------------------
+
+Send frames directly from sensor to camera device interface node, with
+no conversions:
+
+-> ipuX_csiY IDMAC pad -> capture node
+
+IC Direct Conversions:
+----------------------
+
+This pipeline uses the preprocess encode entity to route frames directly
+from the CSI to the IC, to carry out scaling up to 1024x1024 resolution,
+CSC, flipping, and image rotation:
+
+-> ipuX_csiY direct pad -> ipuX_ic_prp -> ipuX_ic_prpenc -> capture node
+
+Motion Compensated De-interlace:
+--------------------------------
+
+This pipeline routes frames from the CSI direct pad to the VDIC entity to
+support motion-compensated de-interlacing (high motion mode only),
+scaling up to 1024x1024, CSC, flip, and rotation:
+
+-> ipuX_csiY direct pad -> ipuX_vdic direct pad -> ipuX_ic_prp ->
+   ipuX_ic_prpvf -> capture node
+
+
+Usage Notes
+-----------
+
+Many of the subdevs require information from the active sensor in the
+current pipeline when configuring pad formats. Therefore the media links
+should be established before configuring the media pad formats.
+
+Similarly, the capture device interfaces inherit controls from the
+active entities in the current pipeline at link-setup time. Therefore
+the capture device node links should be the last links established in
+order for the capture interfaces to "see" and inherit all possible
+controls.
+
+The following are usage notes for Sabre- reference platforms:
+
+
+SabreLite with OV5642 and OV5640
+--------------------------------
+
+This platform requires the OmniVision OV5642 module with a parallel
+camera interface, and the OV5640 module with a MIPI CSI-2
+interface. Both modules are available from Boundary Devices:
+
+https://boundarydevices.com/products/nit6x_5mp
+https://boundarydevices.com/product/nit6x_5mp_mipi
+
+Note that if only one camera module is available, the other sensor
+node can be disabled in the device tree.
+
+The OV5642 module is connected to the parallel bus input on the i.MX
+internal video mux to IPU1 CSI0. It's i2c bus connects to i2c bus 2.
+
+The MIPI CSI-2 OV5640 module is connected to the i.MX internal MIPI CSI-2
+receiver, and the four virtual channel outputs from the receiver are
+routed as follows: vc0 to the IPU1 CSI0 mux, vc1 directly to IPU1 CSI1,
+vc2 directly to IPU2 CSI0, and vc3 to the IPU2 CSI1 mux. The OV5640 is
+also connected to i2c bus 2 on the SabreLite, therefore the OV5642 and
+OV5640 must not share the same i2c slave address.
+
+The following basic example configures unprocessed video capture
+pipelines for both sensors. The OV5642 is routed to ipu1_csi0, and
+the OV5640 (transmitting on mipi csi-2 virtual channel 1) is routed
+to ipu1_csi1. Both sensors are configured to output 640x480, the
+OV5642 outputs YUYV2X8, the OV5640 UYVY2X8:
+
+.. code-block:: none
+
+   # Setup links for OV5642
+   media-ctl -l '"ov5642 1-0042":0 -> "ipu1_csi0_mux":1[1]'
+   media-ctl -l '"ipu1_csi0_mux":2 -> "ipu1_csi0":0[1]'
+   media-ctl -l '"ipu1_csi0":2 -> "ipu1_csi0 capture":0[1]'
+   # Setup links for OV5640
+   media-ctl -l '"ov5640 1-0040":0 -> "imx6-mipi-csi2":0[1]'
+   media-ctl -l '"imx6-mipi-csi2":2 -> "ipu1_csi1":0[1]'
+   media-ctl -l '"ipu1_csi1":2 -> "ipu1_csi1 capture":0[1]'
+   # Configure pads for OV5642 pipeline
+   media-ctl -V "\"ov5642 1-0042\":0 [fmt:YUYV2X8/640x480 field:none]"
+   media-ctl -V "\"ipu1_csi0_mux\":2 [fmt:YUYV2X8/640x480 field:none]"
+   media-ctl -V "\"ipu1_csi0\":2 [fmt:AYUV32/640x480 field:none]"
+   # Configure pads for OV5640 pipeline
+   media-ctl -V "\"ov5640 1-0040\":0 [fmt:UYVY2X8/640x480 field:none]"
+   media-ctl -V "\"imx6-mipi-csi2\":2 [fmt:UYVY2X8/640x480 field:none]"
+   media-ctl -V "\"ipu1_csi1\":2 [fmt:AYUV32/640x480 field:none]"
+
+Streaming can then begin independently on the capture device nodes
+"ipu1_csi0 capture" and "ipu1_csi1 capture". The v4l2-ctl tool can
+be used to select any supported YUV pixelformat on the capture device
+nodes, including planar.
+
+SabreAuto with ADV7180 decoder
+------------------------------
+
+On the SabreAuto, an on-board ADV7180 SD decoder is connected to the
+parallel bus input on the internal video mux to IPU1 CSI0.
+
+The following example configures a pipeline to capture from the ADV7180
+video decoder, assuming NTSC 720x480 input signals, with Motion
+Compensated de-interlacing. Pad field types assume the adv7180 outputs
+"alternate", which the ipu1_csi0 entity converts to "seq-tb" at its
+source pad. $outputfmt can be any format supported by the ipu1_ic_prpvf
+entity at its output pad:
+
+.. code-block:: none
+
+   # Setup links
+   media-ctl -l '"adv7180 4-0021":0 -> "ipu1_csi0_mux":1[1]'
+   media-ctl -l '"ipu1_csi0_mux":2 -> "ipu1_csi0":0[1]'
+   media-ctl -l '"ipu1_csi0":1 -> "ipu1_vdic":0[1]'
+   media-ctl -l '"ipu1_vdic":2 -> "ipu1_ic_prp":0[1]'
+   media-ctl -l '"ipu1_ic_prp":2 -> "ipu1_ic_prpvf":0[1]'
+   media-ctl -l '"ipu1_ic_prpvf":1 -> "ipu1_ic_prpvf capture":0[1]'
+   # Configure pads
+   media-ctl -V "\"adv7180 4-0021\":0 [fmt:UYVY2X8/720x480]"
+   media-ctl -V "\"ipu1_csi0_mux\":2 [fmt:UYVY2X8/720x480 field:alternate]"
+   media-ctl -V "\"ipu1_csi0\":1 [fmt:AYUV32/720x480 field:seq-tb]"
+   media-ctl -V "\"ipu1_vdic\":2 [fmt:AYUV32/720x480 field:none]"
+   media-ctl -V "\"ipu1_ic_prp\":2 [fmt:AYUV32/720x480 field:none]"
+   media-ctl -V "\"ipu1_ic_prpvf\":1 [fmt:$outputfmt field:none]"
+
+Streaming can then begin on the capture device node at
+"ipu1_ic_prpvf capture". The v4l2-ctl tool can be used to select any
+supported YUV or RGB pixelformat on the capture device node.
+
+This platform accepts Composite Video analog inputs to the ADV7180 on
+Ain1 (connector J42).
+
+Frame Interval Monitor
+----------------------
+
+The adv718x decoders can occasionally send corrupt fields during
+NTSC/PAL signal re-sync (too little or too many video lines). When
+this happens, the IPU triggers a mechanism to re-establish vertical
+sync by adding 1 dummy line every frame, which causes a rolling effect
+from image to image, and can last a long time before a stable image is
+recovered. Or sometimes the mechanism doesn't work at all, causing a
+permanent split image (one frame contains lines from two consecutive
+captured images).
+
+From experiment it was found that during image rolling, the frame
+intervals (elapsed time between two EOF's) drop below the nominal
+value for the current standard, by about one frame time (60 usec),
+and remain at that value until rolling stops.
+
+While the reason for this observation isn't known (the IPU dummy
+line mechanism should show an increase in the intervals by 1 line
+time every frame, not a fixed value), we can use it to detect the
+corrupt fields using a frame interval monitor. If the FIM detects a
+bad frame interval, a subdev event is sent. In response, userland can
+issue a streaming restart to correct the rolling/split image.
+
+The FIM is implemented in the ipuX_csiY entity, and the entities that
+generate End-Of-Frame interrupts call into the FIM to monitor the frame
+intervals: ipuX_ic_prpenc, and ipuX_ic_prpvf. Userland can register with
+the FIM event notifications on the ipuX_csiY subdev device node
+(V4L2_EVENT_FRAME_INTERVAL_ERROR).
+
+The ipuX_csiY entity includes custom controls to tweak some dials for
+FIM. If one of these controls is changed during streaming, the FIM will
+be reset and will continue at the new settings.
+
+- V4L2_CID_IMX_FIM_ENABLE
+
+Enable/disable the FIM.
+
+- V4L2_CID_IMX_FIM_NUM
+
+How many frame interval errors to average before comparing against the
+nominal frame interval reported by the sensor. This can reduce noise
+from interrupt latency.
+
+- V4L2_CID_IMX_FIM_TOLERANCE_MIN
+
+If the averaged intervals fall outside nominal by this amount, in
+microseconds, streaming will be restarted.
+
+- V4L2_CID_IMX_FIM_TOLERANCE_MAX
+
+If any interval errors are higher than this value, those error samples
+are discarded and do not enter into the average. This can be used to
+discard really high interval errors that might be due to very high
+system load, causing excessive interrupt latencies.
+
+- V4L2_CID_IMX_FIM_NUM_SKIP
+
+How many frames to skip after a FIM reset or stream restart before
+FIM begins to average intervals. It has been found that there can
+be a few bad frame intervals after stream restart which are not
+attributed to adv718x sending a corrupt field, so this is used to
+skip those frames to prevent unnecessary restarts.
+
+
+SabreSD with MIPI CSI-2 OV5640
+------------------------------
+
+Similarly to SabreLite, the SabreSD supports a parallel interface
+OV5642 module on IPU1 CSI0, and a MIPI CSI-2 OV5640 module. The OV5642
+connects to i2c bus 1 and the OV5640 to i2c bus 2.
+
+The device tree for SabreSD includes OF graphs for both the parallel
+OV5642 and the MIPI CSI-2 OV5640, but as of this writing only the MIPI
+CSI-2 OV5640 has been tested, so the OV5642 node is currently disabled.
+The OV5640 module connects to MIPI connector J5 (sorry I don't have the
+compatible module part number or URL).
+
+The following example configures a direct conversion pipeline to capture
+from the OV5640. $sensorfmt can be any format supported by the OV5640.
+$sensordim is the frame dimension part of $sensorfmt (minus the mbus
+pixel code). $outputfmt can be any format supported by the
+ipu1_ic_prpenc entity at its output pad:
+
+.. code-block:: none
+
+   # Setup links
+   media-ctl -l '"ov5640 1-003c":0 -> "imx6-mipi-csi2":0[1]'
+   media-ctl -l '"imx6-mipi-csi2":2 -> "ipu1_csi1":0[1]'
+   media-ctl -l '"ipu1_csi1":1 -> "ipu1_ic_prp":0[1]'
+   media-ctl -l '"ipu1_ic_prp":1 -> "ipu1_ic_prpenc":0[1]'
+   media-ctl -l '"ipu1_ic_prpenc":1 -> "ipu1_ic_prpenc capture":0[1]'
+   # Configure pads
+   media-ctl -V "\"ov5640 1-003c\":0 [fmt:$sensorfmt field:none]"
+   media-ctl -V "\"imx6-mipi-csi2\":2 [fmt:$sensorfmt field:none]"
+   media-ctl -V "\"ipu1_csi1\":1 [fmt:AYUV32/$sensordim field:none]"
+   media-ctl -V "\"ipu1_ic_prp\":1 [fmt:AYUV32/$sensordim field:none]"
+   media-ctl -V "\"ipu1_ic_prpenc\":1 [fmt:$outputfmt field:none]"
+
+Streaming can then begin on "ipu1_ic_prpenc capture" node. The v4l2-ctl
+tool can be used to select any supported YUV or RGB pixelformat on the
+capture device node.
+
+
+Known Issues
+------------
+
+1. When using 90 or 270 degree rotation control at capture resolutions
+   near the IC resizer limit of 1024x1024, and combined with planar
+   pixel formats (YUV420, YUV422p), frame capture will often fail with
+   no end-of-frame interrupts from the IDMAC channel. To work around
+   this, use lower resolution and/or packed formats (YUYV, RGB3, etc.)
+   when 90 or 270 rotations are needed.
+
+
+File list
+---------
+
+drivers/staging/media/imx/
+include/media/imx.h
+include/uapi/media/imx.h
+
+References
+----------
+
+[1] "i.MX 6Dual/6Quad Applications Processor Reference Manual"
+[2] "i.MX 6Solo/6DualLite Applications Processor Reference Manual"
+
+
+Authors
+-------
+Steve Longerbeam <steve_longerbeam@mentor.com>
+Philipp Zabel <kernel@pengutronix.de>
+Russell King <linux@armlinux.org.uk>
+
+Copyright (C) 2012-2017 Mentor Graphics Inc.
diff --git a/drivers/staging/media/Kconfig b/drivers/staging/media/Kconfig
index abd0e2d..31af2a0 100644
--- a/drivers/staging/media/Kconfig
+++ b/drivers/staging/media/Kconfig
@@ -25,6 +25,8 @@ source "drivers/staging/media/cxd2099/Kconfig"
 
 source "drivers/staging/media/davinci_vpfe/Kconfig"
 
+source "drivers/staging/media/imx/Kconfig"
+
 source "drivers/staging/media/omap4iss/Kconfig"
 
 source "drivers/staging/media/platform/bcm2835/Kconfig"
diff --git a/drivers/staging/media/Makefile b/drivers/staging/media/Makefile
index dc89325..0bfb65d 100644
--- a/drivers/staging/media/Makefile
+++ b/drivers/staging/media/Makefile
@@ -1,6 +1,7 @@
 obj-$(CONFIG_I2C_BCM2048)	+= bcm2048/
 obj-$(CONFIG_VIDEO_SAMSUNG_S5P_CEC) += s5p-cec/
 obj-$(CONFIG_DVB_CXD2099)	+= cxd2099/
+obj-$(CONFIG_VIDEO_IMX_MEDIA)	+= imx/
 obj-$(CONFIG_LIRC_STAGING)	+= lirc/
 obj-$(CONFIG_VIDEO_BCM2835)	+= platform/bcm2835/
 obj-$(CONFIG_VIDEO_DM365_VPFE)	+= davinci_vpfe/
diff --git a/drivers/staging/media/imx/Kconfig b/drivers/staging/media/imx/Kconfig
new file mode 100644
index 0000000..62a3c34
--- /dev/null
+++ b/drivers/staging/media/imx/Kconfig
@@ -0,0 +1,6 @@
+config VIDEO_IMX_MEDIA
+	tristate "i.MX5/6 V4L2 media core driver"
+	depends on MEDIA_CONTROLLER && VIDEO_V4L2 && ARCH_MXC && IMX_IPUV3_CORE
+	---help---
+	  Say yes here to enable support for video4linux media controller
+	  driver for the i.MX5/6 SOC.
diff --git a/drivers/staging/media/imx/Makefile b/drivers/staging/media/imx/Makefile
new file mode 100644
index 0000000..ddd7d94
--- /dev/null
+++ b/drivers/staging/media/imx/Makefile
@@ -0,0 +1,5 @@
+imx-media-objs := imx-media-dev.o imx-media-internal-sd.o imx-media-of.o
+imx-media-common-objs := imx-media-utils.o imx-media-fim.o
+
+obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media.o
+obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-common.o
diff --git a/drivers/staging/media/imx/TODO b/drivers/staging/media/imx/TODO
new file mode 100644
index 0000000..78f78fa
--- /dev/null
+++ b/drivers/staging/media/imx/TODO
@@ -0,0 +1,17 @@
+
+- Finish v4l2-compliance
+
+- Clean up and move the ov5642 subdev driver to drivers/media/i2c, and
+  create the binding docs for it.
+
+- The Frame Interval Monitor could be exported to v4l2-core for
+  general use.
+
+- At driver load time, the device-tree node that is the original source
+  (the "sensor"), is parsed to record its media bus configuration, and
+  this info is required in imx-media-csi.c to setup the CSI.
+  Laurent Pinchart argues that instead the CSI subdev should call its
+  neighbor's g_mbus_config op (which should be propagated if necessary)
+  to get this info. However Hans Verkuil is planning to remove the
+  g_mbus_config op. For now this driver uses the parsed DT mbus config
+  method until this issue is resolved.
diff --git a/drivers/staging/media/imx/imx-media-dev.c b/drivers/staging/media/imx/imx-media-dev.c
new file mode 100644
index 0000000..5213210
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media-dev.c
@@ -0,0 +1,522 @@
+/*
+ * V4L2 Media Controller Driver for Freescale i.MX5/6 SOC
+ *
+ * Copyright (c) 2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/delay.h>
+#include <linux/fs.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/platform_device.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/timer.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-ioctl.h>
+#include <media/v4l2-mc.h>
+#include <video/imx-ipu-v3.h>
+#include <media/imx.h>
+#include "imx-media.h"
+
+static inline struct imx_media_dev *notifier2dev(struct v4l2_async_notifier *n)
+{
+	return container_of(n, struct imx_media_dev, subdev_notifier);
+}
+
+/*
+ * Find a subdev by device node or device name. This is called during
+ * driver load to form the async subdev list and bind them.
+ */
+struct imx_media_subdev *
+imx_media_find_async_subdev(struct imx_media_dev *imxmd,
+			    struct device_node *np,
+			    const char *devname)
+{
+	struct imx_media_subdev *imxsd;
+	int i;
+
+	for (i = 0; i < imxmd->subdev_notifier.num_subdevs; i++) {
+		imxsd = &imxmd->subdev[i];
+		switch (imxsd->asd.match_type) {
+		case V4L2_ASYNC_MATCH_OF:
+			if (np && imxsd->asd.match.of.node == np)
+				return imxsd;
+			break;
+		case V4L2_ASYNC_MATCH_DEVNAME:
+			if (devname &&
+			    !strcmp(imxsd->asd.match.device_name.name, devname))
+				return imxsd;
+			break;
+		default:
+			break;
+		}
+	}
+
+	return NULL;
+}
+
+/*
+ * Adds a subdev to the async subdev list. If np is non-NULL, adds
+ * the async as a V4L2_ASYNC_MATCH_OF match type, otherwise as a
+ * V4L2_ASYNC_MATCH_DEVNAME match type using the dev_name of the
+ * given platform_device. This is called during driver load when
+ * forming the async subdev list.
+ */
+struct imx_media_subdev *
+imx_media_add_async_subdev(struct imx_media_dev *imxmd,
+			   struct device_node *np,
+			   struct platform_device *pdev)
+{
+	struct imx_media_subdev *imxsd;
+	struct v4l2_async_subdev *asd;
+	const char *devname = NULL;
+	int sd_idx;
+
+	if (pdev)
+		devname = dev_name(&pdev->dev);
+
+	/* return NULL if this subdev already added */
+	if (imx_media_find_async_subdev(imxmd, np, devname)) {
+		dev_dbg(imxmd->md.dev, "%s: already added %s\n",
+			__func__, np ? np->name : devname);
+		return NULL;
+	}
+
+	sd_idx = imxmd->subdev_notifier.num_subdevs;
+	if (sd_idx >= IMX_MEDIA_MAX_SUBDEVS) {
+		dev_err(imxmd->md.dev, "%s: too many subdevs! can't add %s\n",
+			__func__, np ? np->name : devname);
+		return ERR_PTR(-ENOSPC);
+	}
+
+	imxsd = &imxmd->subdev[sd_idx];
+
+	asd = &imxsd->asd;
+	if (np) {
+		asd->match_type = V4L2_ASYNC_MATCH_OF;
+		asd->match.of.node = np;
+	} else {
+		asd->match_type = V4L2_ASYNC_MATCH_DEVNAME;
+		strncpy(imxsd->devname, devname, sizeof(imxsd->devname));
+		asd->match.device_name.name = imxsd->devname;
+		imxsd->pdev = pdev;
+	}
+
+	imxmd->async_ptrs[sd_idx] = asd;
+	imxmd->subdev_notifier.num_subdevs++;
+
+	dev_dbg(imxmd->md.dev, "%s: added %s, match type %s\n",
+		__func__, np ? np->name : devname, np ? "OF" : "DEVNAME");
+
+	return imxsd;
+}
+
+/*
+ * Adds an imx-media link to a subdev pad's link list. This is called
+ * during driver load when forming the links between subdevs.
+ *
+ * @pad: the local pad
+ * @remote_node: the device node of the remote subdev
+ * @remote_devname: the device name of the remote subdev
+ * @local_pad: local pad index
+ * @remote_pad: remote pad index
+ */
+int imx_media_add_pad_link(struct imx_media_dev *imxmd,
+			   struct imx_media_pad *pad,
+			   struct device_node *remote_node,
+			   const char *remote_devname,
+			   int local_pad, int remote_pad)
+{
+	struct imx_media_link *link;
+	int link_idx;
+
+	link_idx = pad->num_links;
+	if (link_idx >= IMX_MEDIA_MAX_LINKS) {
+		dev_err(imxmd->md.dev, "%s: too many links!\n", __func__);
+		return -ENOSPC;
+	}
+
+	link = &pad->link[link_idx];
+
+	link->remote_sd_node = remote_node;
+	if (remote_devname)
+		strncpy(link->remote_devname, remote_devname,
+			sizeof(link->remote_devname));
+
+	link->local_pad = local_pad;
+	link->remote_pad = remote_pad;
+
+	pad->num_links++;
+
+	return 0;
+}
+
+/*
+ * get IPU from this CSI and add it to the list of IPUs
+ * the media driver will control.
+ */
+static int imx_media_get_ipu(struct imx_media_dev *imxmd,
+			     struct v4l2_subdev *csi_sd)
+{
+	struct ipu_soc *ipu;
+	int ipu_id;
+
+	ipu = dev_get_drvdata(csi_sd->dev->parent);
+	if (!ipu) {
+		v4l2_err(&imxmd->v4l2_dev,
+			 "CSI %s has no parent IPU!\n", csi_sd->name);
+		return -ENODEV;
+	}
+
+	ipu_id = ipu_get_num(ipu);
+	if (ipu_id > 1) {
+		v4l2_err(&imxmd->v4l2_dev, "invalid IPU id %d!\n", ipu_id);
+		return -ENODEV;
+	}
+
+	if (!imxmd->ipu[ipu_id])
+		imxmd->ipu[ipu_id] = ipu;
+
+	return 0;
+}
+
+/* async subdev bound notifier */
+static int imx_media_subdev_bound(struct v4l2_async_notifier *notifier,
+				  struct v4l2_subdev *sd,
+				  struct v4l2_async_subdev *asd)
+{
+	struct imx_media_dev *imxmd = notifier2dev(notifier);
+	struct imx_media_subdev *imxsd;
+	int ret = -EINVAL;
+
+	imxsd = imx_media_find_async_subdev(imxmd, sd->of_node,
+					    dev_name(sd->dev));
+	if (!imxsd)
+		goto out;
+
+	if (sd->grp_id & IMX_MEDIA_GRP_ID_CSI) {
+		ret = imx_media_get_ipu(imxmd, sd);
+		if (ret)
+			return ret;
+	} else if (sd->entity.function == MEDIA_ENT_F_VID_MUX) {
+		/* this is a video mux */
+		sd->grp_id = IMX_MEDIA_GRP_ID_VIDMUX;
+	} else if (imxsd->num_sink_pads == 0) {
+		/*
+		 * this is an original source of video frames, it
+		 * could be a camera sensor, an analog decoder, or
+		 * a bridge device (HDMI -> MIPI CSI-2 for example).
+		 * This group ID is used to locate the entity that
+		 * is the original source of video in a pipeline.
+		 */
+		sd->grp_id = IMX_MEDIA_GRP_ID_SENSOR;
+	}
+
+	/* attach the subdev */
+	imxsd->sd = sd;
+
+	ret = 0;
+out:
+	if (ret)
+		v4l2_warn(&imxmd->v4l2_dev,
+			  "Received unknown subdev %s\n", sd->name);
+	else
+		v4l2_info(&imxmd->v4l2_dev,
+			  "Registered subdev %s\n", sd->name);
+
+	return ret;
+}
+
+/*
+ * create a single media link given a local subdev, a single pad from that
+ * subdev, and a single link from that pad. Called after all subdevs have
+ * registered.
+ */
+static int imx_media_create_link(struct imx_media_dev *imxmd,
+				 struct imx_media_subdev *local_sd,
+				 struct imx_media_pad *pad,
+				 struct imx_media_link *link)
+{
+	struct imx_media_subdev *remote_sd;
+	struct v4l2_subdev *source, *sink;
+	u16 source_pad, sink_pad;
+	int ret;
+
+	/* only create the source->sink links */
+	if (pad->pad.flags & MEDIA_PAD_FL_SINK)
+		return 0;
+
+	remote_sd = imx_media_find_async_subdev(imxmd, link->remote_sd_node,
+						link->remote_devname);
+	if (!remote_sd) {
+		v4l2_warn(&imxmd->v4l2_dev, "%s: no remote for %s:%d\n",
+			  __func__, local_sd->sd->name, link->local_pad);
+		return 0;
+	}
+
+	source = local_sd->sd;
+	sink = remote_sd->sd;
+	source_pad = link->local_pad;
+	sink_pad = link->remote_pad;
+
+	v4l2_info(&imxmd->v4l2_dev, "%s: %s:%d -> %s:%d\n", __func__,
+		  source->name, source_pad, sink->name, sink_pad);
+
+	ret = media_create_pad_link(&source->entity, source_pad,
+				    &sink->entity, sink_pad, 0);
+	if (ret)
+		v4l2_err(&imxmd->v4l2_dev,
+			 "create_pad_link failed: %d\n", ret);
+
+	return ret;
+}
+
+/*
+ * create the media links from all imx-media pads and their links.
+ * Called after all subdevs have registered.
+ */
+static int imx_media_create_links(struct imx_media_dev *imxmd)
+{
+	struct imx_media_subdev *local_sd;
+	struct imx_media_link *link;
+	struct imx_media_pad *pad;
+	int num_pads, i, j, k;
+	int ret = 0;
+
+	for (i = 0; i < imxmd->num_subdevs; i++) {
+		local_sd = &imxmd->subdev[i];
+		num_pads = local_sd->num_sink_pads + local_sd->num_src_pads;
+
+		for (j = 0; j < num_pads; j++) {
+			pad = &local_sd->pad[j];
+
+			for (k = 0; k < pad->num_links; k++) {
+				link = &pad->link[k];
+
+				ret = imx_media_create_link(imxmd, local_sd,
+							    pad, link);
+				if (ret)
+					goto out;
+			}
+		}
+	}
+
+out:
+	return ret;
+}
+
+/* async subdev complete notifier */
+static int imx_media_probe_complete(struct v4l2_async_notifier *notifier)
+{
+	struct imx_media_dev *imxmd = notifier2dev(notifier);
+	int i, ret;
+
+	mutex_lock(&imxmd->md.graph_mutex);
+
+	/* make sure all subdevs were bound */
+	for (i = 0; i < imxmd->num_subdevs; i++) {
+		if (!imxmd->subdev[i].sd) {
+			v4l2_err(&imxmd->v4l2_dev, "unbound subdev!\n");
+			ret = -ENODEV;
+			goto unlock;
+		}
+	}
+
+	ret = imx_media_create_links(imxmd);
+	if (ret)
+		goto unlock;
+
+	ret = v4l2_device_register_subdev_nodes(&imxmd->v4l2_dev);
+unlock:
+	mutex_unlock(&imxmd->md.graph_mutex);
+	if (ret)
+		return ret;
+
+	return media_device_register(&imxmd->md);
+}
+
+static int imx_media_link_notify(struct media_link *link, u32 flags,
+				 unsigned int notification)
+{
+	struct media_entity *source = link->source->entity;
+	struct media_entity *sink = link->sink->entity;
+	struct imx_media_dev *imxmd;
+	struct media_graph *graph;
+	struct video_device *vdev;
+	struct v4l2_subdev *sd;
+	int ret = 0;
+
+	if (is_media_entity_v4l2_subdev(sink))
+		sd = media_entity_to_v4l2_subdev(sink);
+	else
+		sd = media_entity_to_v4l2_subdev(source);
+
+	imxmd = dev_get_drvdata(sd->v4l2_dev->dev);
+	graph = &imxmd->link_notify_graph;
+
+	vdev = imx_media_find_pipeline_video_device(imxmd, sink);
+	if (!IS_ERR(vdev)) {
+		/*
+		 * reset video device controls on any change to
+		 * the pipeline.
+		 */
+		v4l2_ctrl_handler_free(vdev->ctrl_handler);
+		v4l2_ctrl_handler_init(vdev->ctrl_handler, 0);
+	} else {
+		vdev = NULL;
+	}
+
+	if (notification == MEDIA_DEV_NOTIFY_PRE_LINK_CH) {
+		ret = media_graph_walk_init(graph, &imxmd->md);
+		if (ret)
+			return ret;
+
+		if (flags & MEDIA_LNK_FL_ENABLED)
+			return 0;
+
+		/* Before link disconnection */
+		return imx_media_pipeline_set_power(imxmd, graph, sink, false);
+	}
+
+	/* MEDIA_DEV_NOTIFY_POST_LINK_CH */
+
+	if (!(link->flags & MEDIA_LNK_FL_ENABLED))
+		goto cleanup;
+
+	/* After link activation */
+	ret = imx_media_pipeline_set_power(imxmd, graph, sink, true);
+	if (ret)
+		goto cleanup;
+
+	if (vdev)
+		ret = __v4l2_pipeline_inherit_controls(vdev, sink);
+cleanup:
+	media_graph_walk_cleanup(graph);
+	return ret ? -EPIPE : 0;
+}
+
+static const struct media_device_ops imx_media_md_ops = {
+	.link_notify = imx_media_link_notify,
+};
+
+static int imx_media_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *node = dev->of_node;
+	struct imx_media_subdev *csi[4] = {0};
+	struct imx_media_dev *imxmd;
+	int ret;
+
+	imxmd = devm_kzalloc(dev, sizeof(*imxmd), GFP_KERNEL);
+	if (!imxmd)
+		return -ENOMEM;
+
+	dev_set_drvdata(dev, imxmd);
+
+	strlcpy(imxmd->md.model, "imx-media", sizeof(imxmd->md.model));
+	imxmd->md.ops = &imx_media_md_ops;
+	imxmd->md.dev = dev;
+
+	imxmd->v4l2_dev.mdev = &imxmd->md;
+	strlcpy(imxmd->v4l2_dev.name, "imx-media",
+		sizeof(imxmd->v4l2_dev.name));
+
+	media_device_init(&imxmd->md);
+
+	ret = v4l2_device_register(dev, &imxmd->v4l2_dev);
+	if (ret < 0) {
+		v4l2_err(&imxmd->v4l2_dev,
+			 "Failed to register v4l2_device: %d\n", ret);
+		goto cleanup;
+	}
+
+	dev_set_drvdata(imxmd->v4l2_dev.dev, imxmd);
+
+	ret = imx_media_of_parse(imxmd, &csi, node);
+	if (ret) {
+		v4l2_err(&imxmd->v4l2_dev,
+			 "imx_media_of_parse failed with %d\n", ret);
+		goto unreg_dev;
+	}
+
+	ret = imx_media_add_internal_subdevs(imxmd, csi);
+	if (ret) {
+		v4l2_err(&imxmd->v4l2_dev,
+			 "add_internal_subdevs failed with %d\n", ret);
+		goto unreg_dev;
+	}
+
+	/* no subdevs? just bail */
+	imxmd->num_subdevs = imxmd->subdev_notifier.num_subdevs;
+	if (imxmd->num_subdevs == 0) {
+		ret = -ENODEV;
+		goto unreg_dev;
+	}
+
+	/* prepare the async subdev notifier and register it */
+	imxmd->subdev_notifier.subdevs = imxmd->async_ptrs;
+	imxmd->subdev_notifier.bound = imx_media_subdev_bound;
+	imxmd->subdev_notifier.complete = imx_media_probe_complete;
+	ret = v4l2_async_notifier_register(&imxmd->v4l2_dev,
+					   &imxmd->subdev_notifier);
+	if (ret) {
+		v4l2_err(&imxmd->v4l2_dev,
+			 "v4l2_async_notifier_register failed with %d\n", ret);
+		goto del_int;
+	}
+
+	return 0;
+
+del_int:
+	imx_media_remove_internal_subdevs(imxmd);
+unreg_dev:
+	v4l2_device_unregister(&imxmd->v4l2_dev);
+cleanup:
+	media_device_cleanup(&imxmd->md);
+	return ret;
+}
+
+static int imx_media_remove(struct platform_device *pdev)
+{
+	struct imx_media_dev *imxmd =
+		(struct imx_media_dev *)platform_get_drvdata(pdev);
+
+	v4l2_info(&imxmd->v4l2_dev, "Removing imx-media\n");
+
+	v4l2_async_notifier_unregister(&imxmd->subdev_notifier);
+	imx_media_remove_internal_subdevs(imxmd);
+	v4l2_device_unregister(&imxmd->v4l2_dev);
+	media_device_unregister(&imxmd->md);
+	media_device_cleanup(&imxmd->md);
+
+	return 0;
+}
+
+static const struct of_device_id imx_media_dt_ids[] = {
+	{ .compatible = "fsl,imx-capture-subsystem" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, imx_media_dt_ids);
+
+static struct platform_driver imx_media_pdrv = {
+	.probe		= imx_media_probe,
+	.remove		= imx_media_remove,
+	.driver		= {
+		.name	= "imx-media",
+		.of_match_table	= imx_media_dt_ids,
+	},
+};
+
+module_platform_driver(imx_media_pdrv);
+
+MODULE_DESCRIPTION("i.MX5/6 v4l2 media controller driver");
+MODULE_AUTHOR("Steve Longerbeam <steve_longerbeam@mentor.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/staging/media/imx/imx-media-fim.c b/drivers/staging/media/imx/imx-media-fim.c
new file mode 100644
index 0000000..824d257
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media-fim.c
@@ -0,0 +1,471 @@
+/*
+ * Frame Interval Monitor.
+ *
+ * Copyright (c) 2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-of.h>
+#include <media/v4l2-subdev.h>
+#include <media/imx.h>
+#include "imx-media.h"
+
+enum {
+	FIM_CL_ENABLE = 0,
+	FIM_CL_NUM,
+	FIM_CL_TOLERANCE_MIN,
+	FIM_CL_TOLERANCE_MAX,
+	FIM_CL_NUM_SKIP,
+	FIM_NUM_CONTROLS,
+};
+
+#define FIM_CL_ENABLE_DEF          1 /* FIM enabled by default */
+#define FIM_CL_NUM_DEF             8 /* average 8 frames */
+#define FIM_CL_NUM_SKIP_DEF        2 /* skip 2 frames after restart */
+#define FIM_CL_TOLERANCE_MIN_DEF  50 /* usec */
+#define FIM_CL_TOLERANCE_MAX_DEF   0 /* no max tolerance (unbounded) */
+
+struct imx_media_fim {
+	struct imx_media_dev *md;
+
+	/* the owning subdev of this fim instance */
+	struct v4l2_subdev *sd;
+
+	/* FIM's control handler */
+	struct v4l2_ctrl_handler ctrl_handler;
+
+	/* control cluster */
+	struct v4l2_ctrl  *ctrl[FIM_NUM_CONTROLS];
+
+	/* current control values */
+	bool              enabled;
+	int               num_avg;
+	int               num_skip;
+	unsigned long     tolerance_min; /* usec */
+	unsigned long     tolerance_max; /* usec */
+
+	int               counter;
+	struct timespec   last_ts;
+	unsigned long     sum;       /* usec */
+	unsigned long     nominal;   /* usec */
+
+	/*
+	 * input capture method of measuring FI (channel and flags
+	 * from device tree)
+	 */
+	int               icap_channel;
+	int               icap_flags;
+	struct completion icap_first_event;
+};
+
+static void update_fim_nominal(struct imx_media_fim *fim,
+			       struct imx_media_subdev *sensor)
+{
+	struct v4l2_streamparm parm;
+	struct v4l2_fract tpf;
+	int ret;
+
+	parm.type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
+	ret = v4l2_subdev_call(sensor->sd, video, g_parm, &parm);
+	tpf = parm.parm.capture.timeperframe;
+
+	if (ret || tpf.denominator == 0) {
+		dev_dbg(fim->sd->dev, "no tpf from sensor, FIM disabled\n");
+		fim->enabled = false;
+		return;
+	}
+
+	fim->nominal = DIV_ROUND_CLOSEST(1000 * 1000 * tpf.numerator,
+					 tpf.denominator);
+
+	dev_dbg(fim->sd->dev, "sensor FI=%lu usec\n", fim->nominal);
+}
+
+static void reset_fim(struct imx_media_fim *fim, bool curval)
+{
+	struct v4l2_ctrl *en = fim->ctrl[FIM_CL_ENABLE];
+	struct v4l2_ctrl *num = fim->ctrl[FIM_CL_NUM];
+	struct v4l2_ctrl *skip = fim->ctrl[FIM_CL_NUM_SKIP];
+	struct v4l2_ctrl *tol_min = fim->ctrl[FIM_CL_TOLERANCE_MIN];
+	struct v4l2_ctrl *tol_max = fim->ctrl[FIM_CL_TOLERANCE_MAX];
+
+	if (curval) {
+		fim->enabled = en->cur.val;
+		fim->num_avg = num->cur.val;
+		fim->num_skip = skip->cur.val;
+		fim->tolerance_min = tol_min->cur.val;
+		fim->tolerance_max = tol_max->cur.val;
+	} else {
+		fim->enabled = en->val;
+		fim->num_avg = num->val;
+		fim->num_skip = skip->val;
+		fim->tolerance_min = tol_min->val;
+		fim->tolerance_max = tol_max->val;
+	}
+
+	/* disable tolerance range if max <= min */
+	if (fim->tolerance_max <= fim->tolerance_min)
+		fim->tolerance_max = 0;
+
+	fim->counter = -fim->num_skip;
+	fim->sum = 0;
+}
+
+static void send_fim_event(struct imx_media_fim *fim, unsigned long error)
+{
+	static const struct v4l2_event ev = {
+		.type = V4L2_EVENT_FRAME_INTERVAL_ERROR,
+	};
+
+	v4l2_subdev_notify_event(fim->sd, &ev);
+}
+
+/*
+ * Monitor an averaged frame interval. If the average deviates too much
+ * from the sensor's nominal frame rate, send the frame interval error
+ * event. The frame intervals are averaged in order to quiet noise from
+ * (presumably random) interrupt latency.
+ */
+static void frame_interval_monitor(struct imx_media_fim *fim,
+				   struct timespec *ts)
+{
+	unsigned long interval, error, error_avg;
+	struct timespec diff;
+	bool send_event = false;
+
+	if (!fim->enabled || ++fim->counter <= 0)
+		goto out_update_ts;
+
+	diff = timespec_sub(*ts, fim->last_ts);
+	interval = diff.tv_sec * 1000 * 1000 + diff.tv_nsec / 1000;
+	error = abs(interval - fim->nominal);
+
+	if (fim->tolerance_max && error >= fim->tolerance_max) {
+		dev_dbg(fim->sd->dev,
+			"FIM: %lu ignored, out of tolerance bounds\n",
+			error);
+		fim->counter--;
+		goto out_update_ts;
+	}
+
+	fim->sum += error;
+
+	if (fim->counter == fim->num_avg) {
+		error_avg = DIV_ROUND_CLOSEST(fim->sum, fim->num_avg);
+
+		if (error_avg > fim->tolerance_min)
+			send_event = true;
+
+		dev_dbg(fim->sd->dev, "FIM: error: %lu usec%s\n",
+			error_avg, send_event ? " (!!!)" : "");
+
+		fim->counter = 0;
+		fim->sum = 0;
+	}
+
+out_update_ts:
+	fim->last_ts = *ts;
+	if (send_event)
+		send_fim_event(fim, error_avg);
+}
+
+#ifdef CONFIG_IMX_GPT_ICAP
+/*
+ * Input Capture method of measuring frame intervals. Not subject
+ * to interrupt latency.
+ */
+static void fim_input_capture_handler(int channel, void *dev_id,
+				      struct timespec *ts)
+{
+	struct imx_media_fim *fim = dev_id;
+
+	frame_interval_monitor(fim, ts);
+
+	if (!completion_done(&fim->icap_first_event))
+		complete(&fim->icap_first_event);
+}
+
+static int fim_request_input_capture(struct imx_media_fim *fim)
+{
+	init_completion(&fim->icap_first_event);
+
+	return mxc_request_input_capture(fim->icap_channel,
+					 fim_input_capture_handler,
+					 fim->icap_flags, fim);
+}
+
+static void fim_free_input_capture(struct imx_media_fim *fim)
+{
+	mxc_free_input_capture(fim->icap_channel, fim);
+}
+
+#else /* CONFIG_IMX_GPT_ICAP */
+
+static int fim_request_input_capture(struct imx_media_fim *fim)
+{
+	return 0;
+}
+
+static void fim_free_input_capture(struct imx_media_fim *fim)
+{
+}
+
+#endif /* CONFIG_IMX_GPT_ICAP */
+
+/*
+ * In case we are monitoring the first frame interval after streamon
+ * (when fim->num_skip = 0), we need a valid fim->last_ts before we
+ * can begin. This only applies to the input capture method. It is not
+ * possible to accurately measure the first FI after streamon using the
+ * EOF method, so fim->num_skip minimum is set to 1 in that case, so this
+ * function is a noop when the EOF method is used.
+ */
+static void fim_acquire_first_ts(struct imx_media_fim *fim)
+{
+	unsigned long ret;
+
+	if (!fim->enabled || fim->num_skip > 0)
+		return;
+
+	ret = wait_for_completion_timeout(
+		&fim->icap_first_event,
+		msecs_to_jiffies(IMX_MEDIA_EOF_TIMEOUT));
+	if (ret == 0)
+		v4l2_warn(fim->sd, "wait first icap event timeout\n");
+}
+
+/* FIM Controls */
+static int fim_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct imx_media_fim *fim = container_of(ctrl->handler,
+						 struct imx_media_fim,
+						 ctrl_handler);
+
+	switch (ctrl->id) {
+	case V4L2_CID_IMX_FIM_ENABLE:
+		reset_fim(fim, false);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static const struct v4l2_ctrl_ops fim_ctrl_ops = {
+	.s_ctrl = fim_s_ctrl,
+};
+
+static const struct v4l2_ctrl_config imx_media_fim_ctrl[] = {
+	[FIM_CL_ENABLE] = {
+		.ops = &fim_ctrl_ops,
+		.id = V4L2_CID_IMX_FIM_ENABLE,
+		.name = "FIM Enable",
+		.type = V4L2_CTRL_TYPE_BOOLEAN,
+		.def = FIM_CL_ENABLE_DEF,
+		.min = 0,
+		.max = 1,
+		.step = 1,
+	},
+	[FIM_CL_NUM] = {
+		.ops = &fim_ctrl_ops,
+		.id = V4L2_CID_IMX_FIM_NUM,
+		.name = "FIM Num Average",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.def = FIM_CL_NUM_DEF,
+		.min =  1, /* no averaging */
+		.max = 64, /* average 64 frames */
+		.step = 1,
+	},
+	[FIM_CL_TOLERANCE_MIN] = {
+		.ops = &fim_ctrl_ops,
+		.id = V4L2_CID_IMX_FIM_TOLERANCE_MIN,
+		.name = "FIM Tolerance Min",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.def = FIM_CL_TOLERANCE_MIN_DEF,
+		.min =    2,
+		.max =  200,
+		.step =   1,
+	},
+	[FIM_CL_TOLERANCE_MAX] = {
+		.ops = &fim_ctrl_ops,
+		.id = V4L2_CID_IMX_FIM_TOLERANCE_MAX,
+		.name = "FIM Tolerance Max",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.def = FIM_CL_TOLERANCE_MAX_DEF,
+		.min =    0,
+		.max =  500,
+		.step =   1,
+	},
+	[FIM_CL_NUM_SKIP] = {
+		.ops = &fim_ctrl_ops,
+		.id = V4L2_CID_IMX_FIM_NUM_SKIP,
+		.name = "FIM Num Skip",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.def = FIM_CL_NUM_SKIP_DEF,
+		.min =   0, /* skip no frames */
+		.max = 256, /* skip 256 frames */
+		.step =  1,
+	},
+};
+
+static int init_fim_controls(struct imx_media_fim *fim)
+{
+	struct v4l2_ctrl_handler *hdlr = &fim->ctrl_handler;
+	struct v4l2_ctrl_config fim_c;
+	int i, ret;
+
+	v4l2_ctrl_handler_init(hdlr, FIM_NUM_CONTROLS);
+
+	for (i = 0; i < FIM_NUM_CONTROLS; i++) {
+		fim_c = imx_media_fim_ctrl[i];
+
+		/*
+		 * it's not possible to accurately measure the first
+		 * FI after streamon using the EOF method, so force
+		 * num_skip minimum to 1 in that case.
+		 */
+		if (i == FIM_CL_NUM_SKIP && fim->icap_channel < 0)
+			fim_c.min = 1;
+
+		fim->ctrl[i] = v4l2_ctrl_new_custom(hdlr, &fim_c, NULL);
+	}
+
+	if (hdlr->error) {
+		ret = hdlr->error;
+		goto err_free;
+	}
+
+	v4l2_ctrl_cluster(FIM_NUM_CONTROLS, fim->ctrl);
+
+	/* add the FIM controls to the calling subdev ctrl handler */
+	ret = v4l2_ctrl_add_handler(fim->sd->ctrl_handler,
+				    &fim->ctrl_handler, NULL);
+	if (ret)
+		goto err_free;
+
+	return 0;
+err_free:
+	v4l2_ctrl_handler_free(hdlr);
+	return ret;
+}
+
+static int of_parse_fim(struct imx_media_fim *fim, struct device_node *np)
+{
+	struct device_node *fim_np;
+	u32 icap[2];
+	int ret;
+
+	/* by default EOF method is used */
+	fim->icap_channel = -1;
+
+	fim_np = of_get_child_by_name(np, "fim");
+	if (!fim_np || !of_device_is_available(fim_np)) {
+		of_node_put(fim_np);
+		return -ENODEV;
+	}
+
+	if (IS_ENABLED(CONFIG_IMX_GPT_ICAP)) {
+		ret = of_property_read_u32_array(fim_np,
+						 "fsl,input-capture-channel",
+						 icap, 2);
+		if (!ret) {
+			fim->icap_channel = icap[0];
+			fim->icap_flags = icap[1];
+		}
+	}
+
+	of_node_put(fim_np);
+	return 0;
+}
+
+/*
+ * Monitor frame intervals via EOF interrupt. This method is
+ * subject to uncertainty errors introduced by interrupt latency.
+ *
+ * This is a noop if the Input Capture method is being used, since
+ * the frame_interval_monitor() is called by the input capture event
+ * callback handler in that case.
+ */
+void imx_media_fim_eof_monitor(struct imx_media_fim *fim, struct timespec *ts)
+{
+	if (fim->icap_channel >= 0)
+		return;
+
+	frame_interval_monitor(fim, ts);
+}
+EXPORT_SYMBOL_GPL(imx_media_fim_eof_monitor);
+
+/* Called by the subdev in its s_power callback */
+int imx_media_fim_set_power(struct imx_media_fim *fim, bool on)
+{
+	int ret = 0;
+
+	if (fim->icap_channel >= 0) {
+		if (on)
+			ret = fim_request_input_capture(fim);
+		else
+			fim_free_input_capture(fim);
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(imx_media_fim_set_power);
+
+/* Called by the subdev in its s_stream callback */
+int imx_media_fim_set_stream(struct imx_media_fim *fim,
+			     struct imx_media_subdev *sensor,
+			     bool on)
+{
+	if (on) {
+		reset_fim(fim, true);
+		update_fim_nominal(fim, sensor);
+
+		if (fim->icap_channel >= 0)
+			fim_acquire_first_ts(fim);
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_fim_set_stream);
+
+/* Called by the subdev in its subdev registered callback */
+struct imx_media_fim *imx_media_fim_init(struct v4l2_subdev *sd)
+{
+	struct device_node *node = sd->of_node;
+	struct imx_media_fim *fim;
+	int ret;
+
+	fim = devm_kzalloc(sd->dev, sizeof(*fim), GFP_KERNEL);
+	if (!fim)
+		return ERR_PTR(-ENOMEM);
+
+	/* get media device */
+	fim->md = dev_get_drvdata(sd->v4l2_dev->dev);
+	fim->sd = sd;
+
+	ret = of_parse_fim(fim, node);
+	if (ret)
+		return (ret == -ENODEV) ? NULL : ERR_PTR(ret);
+
+	ret = init_fim_controls(fim);
+	if (ret)
+		return ERR_PTR(ret);
+
+	return fim;
+}
+EXPORT_SYMBOL_GPL(imx_media_fim_init);
+
+void imx_media_fim_free(struct imx_media_fim *fim)
+{
+	v4l2_ctrl_handler_free(&fim->ctrl_handler);
+}
+EXPORT_SYMBOL_GPL(imx_media_fim_free);
diff --git a/drivers/staging/media/imx/imx-media-internal-sd.c b/drivers/staging/media/imx/imx-media-internal-sd.c
new file mode 100644
index 0000000..cdfbf40
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media-internal-sd.c
@@ -0,0 +1,349 @@
+/*
+ * Media driver for Freescale i.MX5/6 SOC
+ *
+ * Adds the internal subdevices and the media links between them.
+ *
+ * Copyright (c) 2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/platform_device.h>
+#include "imx-media.h"
+
+enum isd_enum {
+	isd_csi0 = 0,
+	isd_csi1,
+	isd_vdic,
+	isd_ic_prp,
+	isd_ic_prpenc,
+	isd_ic_prpvf,
+	num_isd,
+};
+
+static const struct internal_subdev_id {
+	enum isd_enum index;
+	const char *name;
+	u32 grp_id;
+} isd_id[num_isd] = {
+	[isd_csi0] = {
+		.index = isd_csi0,
+		.grp_id = IMX_MEDIA_GRP_ID_CSI0,
+		.name = "imx-ipuv3-csi",
+	},
+	[isd_csi1] = {
+		.index = isd_csi1,
+		.grp_id = IMX_MEDIA_GRP_ID_CSI1,
+		.name = "imx-ipuv3-csi",
+	},
+	[isd_vdic] = {
+		.index = isd_vdic,
+		.grp_id = IMX_MEDIA_GRP_ID_VDIC,
+		.name = "imx-ipuv3-vdic",
+	},
+	[isd_ic_prp] = {
+		.index = isd_ic_prp,
+		.grp_id = IMX_MEDIA_GRP_ID_IC_PRP,
+		.name = "imx-ipuv3-ic",
+	},
+	[isd_ic_prpenc] = {
+		.index = isd_ic_prpenc,
+		.grp_id = IMX_MEDIA_GRP_ID_IC_PRPENC,
+		.name = "imx-ipuv3-ic",
+	},
+	[isd_ic_prpvf] = {
+		.index = isd_ic_prpvf,
+		.grp_id = IMX_MEDIA_GRP_ID_IC_PRPVF,
+		.name = "imx-ipuv3-ic",
+	},
+};
+
+struct internal_link {
+	const struct internal_subdev_id *remote_id;
+	int remote_pad;
+};
+
+struct internal_pad {
+	bool devnode; /* does this pad link to a device node */
+	struct internal_link link[IMX_MEDIA_MAX_LINKS];
+};
+
+static const struct internal_subdev {
+	const struct internal_subdev_id *id;
+	struct internal_pad pad[IMX_MEDIA_MAX_PADS];
+	int num_sink_pads;
+	int num_src_pads;
+} internal_subdev[num_isd] = {
+	[isd_csi0] = {
+		.id = &isd_id[isd_csi0],
+		.num_sink_pads = CSI_NUM_SINK_PADS,
+		.num_src_pads = CSI_NUM_SRC_PADS,
+		.pad[CSI_SRC_PAD_DIRECT] = {
+			.link = {
+				{
+					.remote_id = &isd_id[isd_ic_prp],
+					.remote_pad = PRP_SINK_PAD,
+				}, {
+					.remote_id =  &isd_id[isd_vdic],
+					.remote_pad = VDIC_SINK_PAD_DIRECT,
+				},
+			},
+		},
+		.pad[CSI_SRC_PAD_IDMAC] = {
+			.devnode = true,
+		},
+	},
+
+	[isd_csi1] = {
+		.id = &isd_id[isd_csi1],
+		.num_sink_pads = CSI_NUM_SINK_PADS,
+		.num_src_pads = CSI_NUM_SRC_PADS,
+		.pad[CSI_SRC_PAD_DIRECT] = {
+			.link = {
+				{
+					.remote_id = &isd_id[isd_ic_prp],
+					.remote_pad = PRP_SINK_PAD,
+				}, {
+					.remote_id =  &isd_id[isd_vdic],
+					.remote_pad = VDIC_SINK_PAD_DIRECT,
+				},
+			},
+		},
+		.pad[CSI_SRC_PAD_IDMAC] = {
+			.devnode = true,
+		},
+	},
+
+	[isd_vdic] = {
+		.id = &isd_id[isd_vdic],
+		.num_sink_pads = VDIC_NUM_SINK_PADS,
+		.num_src_pads = VDIC_NUM_SRC_PADS,
+		.pad[VDIC_SINK_PAD_IDMAC] = {
+			.devnode = true,
+		},
+		.pad[VDIC_SRC_PAD_DIRECT] = {
+			.link = {
+				{
+					.remote_id =  &isd_id[isd_ic_prp],
+					.remote_pad = PRP_SINK_PAD,
+				},
+			},
+		},
+	},
+
+	[isd_ic_prp] = {
+		.id = &isd_id[isd_ic_prp],
+		.num_sink_pads = PRP_NUM_SINK_PADS,
+		.num_src_pads = PRP_NUM_SRC_PADS,
+		.pad[PRP_SRC_PAD_PRPENC] = {
+			.link = {
+				{
+					.remote_id = &isd_id[isd_ic_prpenc],
+					.remote_pad = 0,
+				},
+			},
+		},
+		.pad[PRP_SRC_PAD_PRPVF] = {
+			.link = {
+				{
+					.remote_id = &isd_id[isd_ic_prpvf],
+					.remote_pad = 0,
+				},
+			},
+		},
+	},
+
+	[isd_ic_prpenc] = {
+		.id = &isd_id[isd_ic_prpenc],
+		.num_sink_pads = PRPENCVF_NUM_SINK_PADS,
+		.num_src_pads = PRPENCVF_NUM_SRC_PADS,
+		.pad[PRPENCVF_SRC_PAD] = {
+			.devnode = true,
+		},
+	},
+
+	[isd_ic_prpvf] = {
+		.id = &isd_id[isd_ic_prpvf],
+		.num_sink_pads = PRPENCVF_NUM_SINK_PADS,
+		.num_src_pads = PRPENCVF_NUM_SRC_PADS,
+		.pad[PRPENCVF_SRC_PAD] = {
+			.devnode = true,
+		},
+	},
+};
+
+/* form a device name given a group id and ipu id */
+static inline void isd_id_to_devname(char *devname, int sz,
+				     const struct internal_subdev_id *id,
+				     int ipu_id)
+{
+	int pdev_id = ipu_id * num_isd + id->index;
+
+	snprintf(devname, sz, "%s.%d", id->name, pdev_id);
+}
+
+/* adds the links from given internal subdev */
+static int add_internal_links(struct imx_media_dev *imxmd,
+			      const struct internal_subdev *isd,
+			      struct imx_media_subdev *imxsd,
+			      int ipu_id)
+{
+	int i, num_pads, ret;
+
+	num_pads = isd->num_sink_pads + isd->num_src_pads;
+
+	for (i = 0; i < num_pads; i++) {
+		const struct internal_pad *intpad = &isd->pad[i];
+		struct imx_media_pad *pad = &imxsd->pad[i];
+		int j;
+
+		/* init the pad flags for this internal subdev */
+		pad->pad.flags = (i < isd->num_sink_pads) ?
+			MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
+		/* export devnode pad flag to the subdevs */
+		pad->devnode = intpad->devnode;
+
+		for (j = 0; ; j++) {
+			const struct internal_link *link;
+			char remote_devname[32];
+
+			link = &intpad->link[j];
+
+			if (!link->remote_id)
+				break;
+
+			isd_id_to_devname(remote_devname,
+					  sizeof(remote_devname),
+					  link->remote_id, ipu_id);
+
+			ret = imx_media_add_pad_link(imxmd, pad,
+						     NULL, remote_devname,
+						     i, link->remote_pad);
+			if (ret)
+				return ret;
+		}
+	}
+
+	return 0;
+}
+
+/* register an internal subdev as a platform device */
+static struct imx_media_subdev *
+add_internal_subdev(struct imx_media_dev *imxmd,
+		    const struct internal_subdev *isd,
+		    int ipu_id)
+{
+	struct imx_media_internal_sd_platformdata pdata;
+	struct platform_device_info pdevinfo = {0};
+	struct imx_media_subdev *imxsd;
+	struct platform_device *pdev;
+
+	pdata.grp_id = isd->id->grp_id;
+
+	/* the id of IPU this subdev will control */
+	pdata.ipu_id = ipu_id;
+
+	/* create subdev name */
+	imx_media_grp_id_to_sd_name(pdata.sd_name, sizeof(pdata.sd_name),
+				    pdata.grp_id, ipu_id);
+
+	pdevinfo.name = isd->id->name;
+	pdevinfo.id = ipu_id * num_isd + isd->id->index;
+	pdevinfo.parent = imxmd->md.dev;
+	pdevinfo.data = &pdata;
+	pdevinfo.size_data = sizeof(pdata);
+	pdevinfo.dma_mask = DMA_BIT_MASK(32);
+
+	pdev = platform_device_register_full(&pdevinfo);
+	if (IS_ERR(pdev))
+		return ERR_CAST(pdev);
+
+	imxsd = imx_media_add_async_subdev(imxmd, NULL, pdev);
+	if (IS_ERR(imxsd))
+		return imxsd;
+
+	imxsd->num_sink_pads = isd->num_sink_pads;
+	imxsd->num_src_pads = isd->num_src_pads;
+
+	return imxsd;
+}
+
+/* adds the internal subdevs in one ipu */
+static int add_ipu_internal_subdevs(struct imx_media_dev *imxmd,
+				    struct imx_media_subdev *csi0,
+				    struct imx_media_subdev *csi1,
+				    int ipu_id)
+{
+	enum isd_enum i;
+	int ret;
+
+	for (i = 0; i < num_isd; i++) {
+		const struct internal_subdev *isd = &internal_subdev[i];
+		struct imx_media_subdev *imxsd;
+
+		/*
+		 * the CSIs are represented in the device-tree, so those
+		 * devices are added already, and are added to the async
+		 * subdev list by of_parse_subdev(), so we are given those
+		 * subdevs as csi0 and csi1.
+		 */
+		switch (isd->id->grp_id) {
+		case IMX_MEDIA_GRP_ID_CSI0:
+			imxsd = csi0;
+			break;
+		case IMX_MEDIA_GRP_ID_CSI1:
+			imxsd = csi1;
+			break;
+		default:
+			imxsd = add_internal_subdev(imxmd, isd, ipu_id);
+			break;
+		}
+
+		if (IS_ERR(imxsd))
+			return PTR_ERR(imxsd);
+
+		/* add the links from this subdev */
+		if (imxsd) {
+			ret = add_internal_links(imxmd, isd, imxsd, ipu_id);
+			if (ret)
+				return ret;
+		}
+	}
+
+	return 0;
+}
+
+int imx_media_add_internal_subdevs(struct imx_media_dev *imxmd,
+				   struct imx_media_subdev *csi[4])
+{
+	int ret;
+
+	ret = add_ipu_internal_subdevs(imxmd, csi[0], csi[1], 0);
+	if (ret)
+		goto remove;
+
+	ret = add_ipu_internal_subdevs(imxmd, csi[2], csi[3], 1);
+	if (ret)
+		goto remove;
+
+	return 0;
+
+remove:
+	imx_media_remove_internal_subdevs(imxmd);
+	return ret;
+}
+
+void imx_media_remove_internal_subdevs(struct imx_media_dev *imxmd)
+{
+	struct imx_media_subdev *imxsd;
+	int i;
+
+	for (i = 0; i < imxmd->subdev_notifier.num_subdevs; i++) {
+		imxsd = &imxmd->subdev[i];
+		if (!imxsd->pdev)
+			continue;
+		platform_device_unregister(imxsd->pdev);
+	}
+}
diff --git a/drivers/staging/media/imx/imx-media-of.c b/drivers/staging/media/imx/imx-media-of.c
new file mode 100644
index 0000000..b383be4
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media-of.c
@@ -0,0 +1,267 @@
+/*
+ * Media driver for Freescale i.MX5/6 SOC
+ *
+ * Open Firmware parsing.
+ *
+ * Copyright (c) 2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/of_platform.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-of.h>
+#include <media/v4l2-subdev.h>
+#include <media/videobuf2-dma-contig.h>
+#include <video/imx-ipu-v3.h>
+#include "imx-media.h"
+
+static int of_add_pad_link(struct imx_media_dev *imxmd,
+			   struct imx_media_pad *pad,
+			   struct device_node *local_sd_node,
+			   struct device_node *remote_sd_node,
+			   int local_pad, int remote_pad)
+{
+	dev_dbg(imxmd->md.dev, "%s: adding %s:%d -> %s:%d\n", __func__,
+		local_sd_node->name, local_pad,
+		remote_sd_node->name, remote_pad);
+
+	return imx_media_add_pad_link(imxmd, pad, remote_sd_node, NULL,
+				      local_pad, remote_pad);
+}
+
+static void of_parse_sensor(struct imx_media_dev *imxmd,
+			    struct imx_media_subdev *sensor,
+			    struct device_node *sensor_np)
+{
+	struct device_node *endpoint;
+
+	endpoint = of_graph_get_next_endpoint(sensor_np, NULL);
+	if (endpoint) {
+		v4l2_of_parse_endpoint(endpoint, &sensor->sensor_ep);
+		of_node_put(endpoint);
+	}
+}
+
+static int of_get_port_count(const struct device_node *np)
+{
+	struct device_node *ports, *child;
+	int num = 0;
+
+	/* check if this node has a ports subnode */
+	ports = of_get_child_by_name(np, "ports");
+	if (ports)
+		np = ports;
+
+	for_each_child_of_node(np, child)
+		if (of_node_cmp(child->name, "port") == 0)
+			num++;
+
+	of_node_put(ports);
+	return num;
+}
+
+/*
+ * find the remote device node and remote port id (remote pad #)
+ * given local endpoint node
+ */
+static void of_get_remote_pad(struct device_node *epnode,
+			      struct device_node **remote_node,
+			      int *remote_pad)
+{
+	struct device_node *rp, *rpp;
+	struct device_node *remote;
+
+	rp = of_graph_get_remote_port(epnode);
+	rpp = of_graph_get_remote_port_parent(epnode);
+
+	if (of_device_is_compatible(rpp, "fsl,imx6q-ipu")) {
+		/* the remote is one of the CSI ports */
+		remote = rp;
+		*remote_pad = 0;
+		of_node_put(rpp);
+	} else {
+		remote = rpp;
+		of_property_read_u32(rp, "reg", remote_pad);
+		of_node_put(rp);
+	}
+
+	if (!remote || !of_device_is_available(remote)) {
+		of_node_put(remote);
+		*remote_node = NULL;
+	} else {
+		*remote_node = remote;
+	}
+}
+
+static struct imx_media_subdev *
+of_parse_subdev(struct imx_media_dev *imxmd, struct device_node *sd_np,
+		bool is_csi_port)
+{
+	struct imx_media_subdev *imxsd;
+	int i, num_pads, ret;
+
+	if (!of_device_is_available(sd_np)) {
+		dev_dbg(imxmd->md.dev, "%s: %s not enabled\n", __func__,
+			sd_np->name);
+		return NULL;
+	}
+
+	/* register this subdev with async notifier */
+	imxsd = imx_media_add_async_subdev(imxmd, sd_np, NULL);
+	if (IS_ERR_OR_NULL(imxsd))
+		return imxsd;
+
+	if (is_csi_port) {
+		/*
+		 * the ipu-csi has one sink port and two source ports.
+		 * The source ports are not represented in the device tree,
+		 * but are described by the internal pads and links later.
+		 */
+		num_pads = CSI_NUM_PADS;
+		imxsd->num_sink_pads = CSI_NUM_SINK_PADS;
+	} else if (of_device_is_compatible(sd_np, "fsl,imx6-mipi-csi2")) {
+		num_pads = of_get_port_count(sd_np);
+		/* the mipi csi2 receiver has only one sink port */
+		imxsd->num_sink_pads = 1;
+	} else if (of_device_is_compatible(sd_np, "video-multiplexer")) {
+		num_pads = of_get_port_count(sd_np);
+		/* for the video mux, all but the last port are sinks */
+		imxsd->num_sink_pads = num_pads - 1;
+	} else {
+		num_pads = of_get_port_count(sd_np);
+		if (num_pads != 1) {
+			dev_warn(imxmd->md.dev,
+				 "%s: unknown device %s with %d ports\n",
+				 __func__, sd_np->name, num_pads);
+			return NULL;
+		}
+
+		/*
+		 * we got to this node from this single source port,
+		 * there are no sink pads.
+		 */
+		imxsd->num_sink_pads = 0;
+	}
+
+	if (imxsd->num_sink_pads >= num_pads)
+		return ERR_PTR(-EINVAL);
+
+	imxsd->num_src_pads = num_pads - imxsd->num_sink_pads;
+
+	dev_dbg(imxmd->md.dev, "%s: %s has %d pads (%d sink, %d src)\n",
+		__func__, sd_np->name, num_pads,
+		imxsd->num_sink_pads, imxsd->num_src_pads);
+
+	/*
+	 * With no sink, this subdev node is the original source
+	 * of video, parse it's media bus fur use by the pipeline.
+	 */
+	if (imxsd->num_sink_pads == 0)
+		of_parse_sensor(imxmd, imxsd, sd_np);
+
+	for (i = 0; i < num_pads; i++) {
+		struct device_node *epnode = NULL, *port, *remote_np;
+		struct imx_media_subdev *remote_imxsd;
+		struct imx_media_pad *pad;
+		int remote_pad;
+
+		/* init this pad */
+		pad = &imxsd->pad[i];
+		pad->pad.flags = (i < imxsd->num_sink_pads) ?
+			MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
+
+		if (is_csi_port)
+			port = (i < imxsd->num_sink_pads) ? sd_np : NULL;
+		else
+			port = of_graph_get_port_by_id(sd_np, i);
+		if (!port)
+			continue;
+
+		for_each_child_of_node(port, epnode) {
+			of_get_remote_pad(epnode, &remote_np, &remote_pad);
+			if (!remote_np)
+				continue;
+
+			ret = of_add_pad_link(imxmd, pad, sd_np, remote_np,
+					      i, remote_pad);
+			if (ret) {
+				imxsd = ERR_PTR(ret);
+				break;
+			}
+
+			if (i < imxsd->num_sink_pads) {
+				/* follow sink endpoints upstream */
+				remote_imxsd = of_parse_subdev(imxmd,
+							       remote_np,
+							       false);
+				if (IS_ERR(remote_imxsd)) {
+					imxsd = remote_imxsd;
+					break;
+				}
+			}
+
+			of_node_put(remote_np);
+		}
+
+		if (port != sd_np)
+			of_node_put(port);
+		if (IS_ERR(imxsd)) {
+			of_node_put(remote_np);
+			of_node_put(epnode);
+			break;
+		}
+	}
+
+	return imxsd;
+}
+
+int imx_media_of_parse(struct imx_media_dev *imxmd,
+		       struct imx_media_subdev *(*csi)[4],
+		       struct device_node *np)
+{
+	struct imx_media_subdev *lcsi;
+	struct device_node *csi_np;
+	u32 ipu_id, csi_id;
+	int i, ret;
+
+	for (i = 0; ; i++) {
+		csi_np = of_parse_phandle(np, "ports", i);
+		if (!csi_np)
+			break;
+
+		lcsi = of_parse_subdev(imxmd, csi_np, true);
+		if (IS_ERR(lcsi)) {
+			ret = PTR_ERR(lcsi);
+			goto err_put;
+		}
+
+		ret = of_property_read_u32(csi_np, "reg", &csi_id);
+		if (ret) {
+			dev_err(imxmd->md.dev,
+				"%s: csi port missing reg property!\n",
+				__func__);
+			goto err_put;
+		}
+
+		ipu_id = of_alias_get_id(csi_np->parent, "ipu");
+		of_node_put(csi_np);
+
+		if (ipu_id > 1 || csi_id > 1) {
+			dev_err(imxmd->md.dev,
+				"%s: invalid ipu/csi id (%u/%u)\n",
+				__func__, ipu_id, csi_id);
+			return -EINVAL;
+		}
+
+		(*csi)[ipu_id * 2 + csi_id] = lcsi;
+	}
+
+	return 0;
+err_put:
+	of_node_put(csi_np);
+	return ret;
+}
diff --git a/drivers/staging/media/imx/imx-media-utils.c b/drivers/staging/media/imx/imx-media-utils.c
new file mode 100644
index 0000000..ee50b6a
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media-utils.c
@@ -0,0 +1,766 @@
+/*
+ * V4L2 Media Controller Driver for Freescale i.MX5/6 SOC
+ *
+ * Copyright (c) 2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/module.h>
+#include "imx-media.h"
+
+/*
+ * List of pixel formats for the subdevs. This must be a super-set of
+ * the formats supported by the ipu image converter.
+ *
+ * The non-mbus formats (planar and BGR) must all fall at the end of
+ * this table, otherwise enum_fmt() at media pads will stop before
+ * seeing all the supported mbus formats.
+ */
+static const struct imx_media_pixfmt imx_media_formats[] = {
+	{
+		.fourcc	= V4L2_PIX_FMT_UYVY,
+		.codes  = {
+			MEDIA_BUS_FMT_UYVY8_2X8,
+			MEDIA_BUS_FMT_UYVY8_1X16
+		},
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 16,
+	}, {
+		.fourcc	= V4L2_PIX_FMT_YUYV,
+		.codes  = {
+			MEDIA_BUS_FMT_YUYV8_2X8,
+			MEDIA_BUS_FMT_YUYV8_1X16
+		},
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 16,
+	}, {
+		.fourcc = V4L2_PIX_FMT_YUV32,
+		.codes  = {MEDIA_BUS_FMT_AYUV8_1X32},
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 32,
+		.ipufmt = true,
+	}, {
+		.fourcc	= V4L2_PIX_FMT_RGB565,
+		.codes  = {MEDIA_BUS_FMT_RGB565_2X8_LE},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 16,
+	}, {
+		.fourcc	= V4L2_PIX_FMT_RGB24,
+		.codes  = {
+			MEDIA_BUS_FMT_RGB888_1X24,
+			MEDIA_BUS_FMT_RGB888_2X12_LE
+		},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 24,
+	}, {
+		.fourcc	= V4L2_PIX_FMT_RGB32,
+		.codes  = {MEDIA_BUS_FMT_ARGB8888_1X32},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 32,
+		.ipufmt = true,
+	},
+	/*** non-mbus formats start here ***/
+	{
+		.fourcc	= V4L2_PIX_FMT_BGR24,
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 24,
+	}, {
+		.fourcc	= V4L2_PIX_FMT_BGR32,
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 32,
+	}, {
+		.fourcc	= V4L2_PIX_FMT_YUV420,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 12,
+		.planar = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_YVU420,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 12,
+		.planar = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_YUV422P,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 16,
+		.planar = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_NV12,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 12,
+		.planar = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_NV16,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 16,
+		.planar = true,
+	},
+};
+
+static const u32 imx_media_ipu_internal_codes[] = {
+	MEDIA_BUS_FMT_AYUV8_1X32, MEDIA_BUS_FMT_ARGB8888_1X32,
+};
+
+static inline u32 pixfmt_to_colorspace(const struct imx_media_pixfmt *fmt)
+{
+	return (fmt->cs == IPUV3_COLORSPACE_RGB) ?
+		V4L2_COLORSPACE_SRGB : V4L2_COLORSPACE_SMPTE170M;
+}
+
+static const struct imx_media_pixfmt *find_format(u32 fourcc, u32 code,
+						  bool allow_rgb,
+						  bool allow_planar,
+						  bool ipu_fmt_only)
+{
+	const struct imx_media_pixfmt *fmt, *ret = NULL;
+	int i, j;
+
+	for (i = 0; i < ARRAY_SIZE(imx_media_formats); i++) {
+		fmt = &imx_media_formats[i];
+
+		if (ipu_fmt_only && !fmt->ipufmt)
+			continue;
+
+		if (fourcc && fmt->fourcc == fourcc &&
+		    (fmt->cs != IPUV3_COLORSPACE_RGB || allow_rgb) &&
+		    (!fmt->planar || allow_planar)) {
+			ret = fmt;
+			goto out;
+		}
+
+		for (j = 0; code && fmt->codes[j]; j++) {
+			if (fmt->codes[j] == code && !fmt->planar &&
+			    (fmt->cs != IPUV3_COLORSPACE_RGB || allow_rgb)) {
+				ret = fmt;
+				goto out;
+			}
+		}
+	}
+out:
+	return ret;
+}
+
+const struct imx_media_pixfmt *imx_media_find_format(u32 fourcc, u32 code,
+						     bool allow_rgb,
+						     bool allow_planar)
+{
+	return find_format(fourcc, code, allow_rgb, allow_planar, false);
+}
+EXPORT_SYMBOL_GPL(imx_media_find_format);
+
+const struct imx_media_pixfmt *imx_media_find_ipu_format(u32 fourcc,
+							 u32 code,
+							 bool allow_rgb)
+{
+	return find_format(fourcc, code, allow_rgb, false, true);
+}
+EXPORT_SYMBOL_GPL(imx_media_find_ipu_format);
+
+int imx_media_enum_format(u32 *fourcc, u32 *code, u32 index,
+			  bool allow_rgb, bool allow_planar)
+{
+	const struct imx_media_pixfmt *fmt;
+
+	if (index >= ARRAY_SIZE(imx_media_formats))
+		return -EINVAL;
+
+	fmt = &imx_media_formats[index];
+
+	if ((fmt->cs == IPUV3_COLORSPACE_RGB && !allow_rgb) ||
+	    (fmt->planar && !allow_planar))
+		return -EINVAL;
+
+	if (code)
+		*code = fmt->codes[0];
+	if (fourcc)
+		*fourcc = fmt->fourcc;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_enum_format);
+
+int imx_media_enum_ipu_format(u32 *fourcc, u32 *code, u32 index,
+			      bool allow_rgb)
+{
+	const struct imx_media_pixfmt *fmt;
+	u32 lcode;
+
+	if (index >= ARRAY_SIZE(imx_media_ipu_internal_codes))
+		return -EINVAL;
+
+	lcode = imx_media_ipu_internal_codes[index];
+
+	fmt = find_format(0, lcode, allow_rgb, false, true);
+	if (!fmt)
+		return -EINVAL;
+
+	if (code)
+		*code = fmt->codes[0];
+	if (fourcc)
+		*fourcc = fmt->fourcc;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_enum_ipu_format);
+
+int imx_media_init_mbus_fmt(struct v4l2_mbus_framefmt *mbus,
+			    u32 width, u32 height, u32 code, u32 field,
+			    const struct imx_media_pixfmt **cc)
+{
+	const struct imx_media_pixfmt *lcc;
+
+	mbus->width = width;
+	mbus->height = height;
+	mbus->field = field;
+	if (code == 0)
+		imx_media_enum_format(NULL, &code, 0, true, false);
+	lcc = imx_media_find_format(0, code, true, false);
+	if (!lcc)
+		return -EINVAL;
+	mbus->code = code;
+	mbus->colorspace = pixfmt_to_colorspace(lcc);
+
+	if (cc)
+		*cc = lcc;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_init_mbus_fmt);
+
+int imx_media_mbus_fmt_to_pix_fmt(struct v4l2_pix_format *pix,
+				  struct v4l2_mbus_framefmt *mbus,
+				  const struct imx_media_pixfmt *cc)
+{
+	u32 stride;
+
+	if (!cc) {
+		cc = imx_media_find_format(0, mbus->code, true, false);
+		if (!cc)
+			return -EINVAL;
+	}
+
+	stride = cc->planar ? mbus->width : (mbus->width * cc->bpp) >> 3;
+
+	pix->width = mbus->width;
+	pix->height = mbus->height;
+	pix->pixelformat = cc->fourcc;
+	pix->colorspace = mbus->colorspace;
+	pix->xfer_func = mbus->xfer_func;
+	pix->ycbcr_enc = mbus->ycbcr_enc;
+	pix->quantization = mbus->quantization;
+	pix->field = mbus->field;
+	pix->bytesperline = stride;
+	pix->sizeimage = (pix->width * pix->height * cc->bpp) >> 3;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_mbus_fmt_to_pix_fmt);
+
+int imx_media_mbus_fmt_to_ipu_image(struct ipu_image *image,
+				    struct v4l2_mbus_framefmt *mbus)
+{
+	int ret;
+
+	memset(image, 0, sizeof(*image));
+
+	ret = imx_media_mbus_fmt_to_pix_fmt(&image->pix, mbus, NULL);
+	if (ret)
+		return ret;
+
+	image->rect.width = mbus->width;
+	image->rect.height = mbus->height;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_mbus_fmt_to_ipu_image);
+
+int imx_media_ipu_image_to_mbus_fmt(struct v4l2_mbus_framefmt *mbus,
+				    struct ipu_image *image)
+{
+	const struct imx_media_pixfmt *fmt;
+
+	fmt = imx_media_find_format(image->pix.pixelformat, 0, true, false);
+	if (!fmt)
+		return -EINVAL;
+
+	memset(mbus, 0, sizeof(*mbus));
+	mbus->width = image->pix.width;
+	mbus->height = image->pix.height;
+	mbus->code = fmt->codes[0];
+	mbus->colorspace = pixfmt_to_colorspace(fmt);
+	mbus->field = image->pix.field;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_ipu_image_to_mbus_fmt);
+
+void imx_media_free_dma_buf(struct imx_media_dev *imxmd,
+			    struct imx_media_dma_buf *buf)
+{
+	if (buf->virt)
+		dma_free_coherent(imxmd->md.dev, buf->len,
+				  buf->virt, buf->phys);
+
+	buf->virt = NULL;
+	buf->phys = 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_free_dma_buf);
+
+int imx_media_alloc_dma_buf(struct imx_media_dev *imxmd,
+			    struct imx_media_dma_buf *buf,
+			    int size)
+{
+	imx_media_free_dma_buf(imxmd, buf);
+
+	buf->len = PAGE_ALIGN(size);
+	buf->virt = dma_alloc_coherent(imxmd->md.dev, buf->len, &buf->phys,
+				       GFP_DMA | GFP_KERNEL);
+	if (!buf->virt) {
+		dev_err(imxmd->md.dev, "failed to alloc dma buffer\n");
+		return -ENOMEM;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_alloc_dma_buf);
+
+/* form a subdev name given a group id and ipu id */
+void imx_media_grp_id_to_sd_name(char *sd_name, int sz, u32 grp_id, int ipu_id)
+{
+	int id;
+
+	switch (grp_id) {
+	case IMX_MEDIA_GRP_ID_CSI0...IMX_MEDIA_GRP_ID_CSI1:
+		id = (grp_id >> IMX_MEDIA_GRP_ID_CSI_BIT) - 1;
+		snprintf(sd_name, sz, "ipu%d_csi%d", ipu_id + 1, id);
+		break;
+	case IMX_MEDIA_GRP_ID_VDIC:
+		snprintf(sd_name, sz, "ipu%d_vdic", ipu_id + 1);
+		break;
+	case IMX_MEDIA_GRP_ID_IC_PRP:
+		snprintf(sd_name, sz, "ipu%d_ic_prp", ipu_id + 1);
+		break;
+	case IMX_MEDIA_GRP_ID_IC_PRPENC:
+		snprintf(sd_name, sz, "ipu%d_ic_prpenc", ipu_id + 1);
+		break;
+	case IMX_MEDIA_GRP_ID_IC_PRPVF:
+		snprintf(sd_name, sz, "ipu%d_ic_prpvf", ipu_id + 1);
+		break;
+	default:
+		break;
+	}
+}
+EXPORT_SYMBOL_GPL(imx_media_grp_id_to_sd_name);
+
+struct imx_media_subdev *
+imx_media_find_subdev_by_sd(struct imx_media_dev *imxmd,
+			    struct v4l2_subdev *sd)
+{
+	struct imx_media_subdev *imxsd;
+	int i;
+
+	for (i = 0; i < imxmd->num_subdevs; i++) {
+		imxsd = &imxmd->subdev[i];
+		if (sd == imxsd->sd)
+			return imxsd;
+	}
+
+	return ERR_PTR(-ENODEV);
+}
+EXPORT_SYMBOL_GPL(imx_media_find_subdev_by_sd);
+
+struct imx_media_subdev *
+imx_media_find_subdev_by_id(struct imx_media_dev *imxmd, u32 grp_id)
+{
+	struct imx_media_subdev *imxsd;
+	int i;
+
+	for (i = 0; i < imxmd->num_subdevs; i++) {
+		imxsd = &imxmd->subdev[i];
+		if (imxsd->sd && imxsd->sd->grp_id == grp_id)
+			return imxsd;
+	}
+
+	return ERR_PTR(-ENODEV);
+}
+EXPORT_SYMBOL_GPL(imx_media_find_subdev_by_id);
+
+/*
+ * Search for an entity in the current pipeline, either a subdev
+ * with given grp_id, or a video device if vdev is true.
+ * Called with mdev->graph_mutex held.
+ */
+static struct media_entity *
+find_pipeline_entity(struct imx_media_dev *imxmd,
+		     struct media_graph *graph,
+		     struct media_entity *start_entity,
+		     u32 grp_id, bool vdev)
+{
+	struct media_entity *entity;
+	struct v4l2_subdev *sd;
+
+	media_graph_walk_start(graph, start_entity);
+
+	while ((entity = media_graph_walk_next(graph))) {
+		if ((vdev && !is_media_entity_v4l2_video_device(entity)) ||
+		    (!vdev && !is_media_entity_v4l2_subdev(entity)))
+			continue;
+
+		if (vdev)
+			return entity;
+
+		sd = media_entity_to_v4l2_subdev(entity);
+		if (sd->grp_id & grp_id)
+			return entity;
+	}
+
+	return NULL;
+}
+
+/*
+ * Search for a subdev in the current pipeline with given grp_id.
+ * Called with mdev->graph_mutex held.
+ */
+static struct v4l2_subdev *
+find_pipeline_subdev(struct imx_media_dev *imxmd,
+		     struct media_graph *graph,
+		     struct media_entity *start_entity,
+		     u32 grp_id)
+{
+	struct media_entity *entity = find_pipeline_entity(imxmd, graph,
+							   start_entity,
+							   grp_id, false);
+	return entity ? media_entity_to_v4l2_subdev(entity) : NULL;
+}
+
+/*
+ * Search for a video device in the current pipeline.
+ * Called with mdev->graph_mutex held.
+ */
+static struct video_device *
+find_pipeline_vdev(struct imx_media_dev *imxmd,
+		   struct media_graph *graph,
+		   struct media_entity *start_entity)
+{
+	struct media_entity *entity = find_pipeline_entity(imxmd, graph,
+							   start_entity,
+							   0, true);
+	return entity ? media_entity_to_video_device(entity) : NULL;
+}
+
+/*
+ * Search for an entity in the current pipeline with given grp_id,
+ * then locate the remote enabled source pad from that entity.
+ * Called with mdev->graph_mutex held.
+ */
+static struct media_pad *
+find_pipeline_remote_source_pad(struct imx_media_dev *imxmd,
+				struct media_graph *graph,
+				struct media_entity *start_entity,
+				u32 grp_id)
+{
+	struct media_pad *pad = NULL;
+	struct media_entity *me;
+	struct v4l2_subdev *sd;
+	int i;
+
+	sd = find_pipeline_subdev(imxmd, graph, start_entity, grp_id);
+	if (!sd)
+		return NULL;
+	me = &sd->entity;
+
+	/* Find remote source pad */
+	for (i = 0; i < me->num_pads; i++) {
+		struct media_pad *spad = &me->pads[i];
+
+		if (!(spad->flags & MEDIA_PAD_FL_SINK))
+			continue;
+		pad = media_entity_remote_pad(spad);
+		if (pad)
+			return pad;
+	}
+
+	return NULL;
+}
+
+/*
+ * Find the mipi-csi2 virtual channel reached from the given
+ * start entity in the current pipeline.
+ * Must be called with mdev->graph_mutex held.
+ */
+int imx_media_find_mipi_csi2_channel(struct imx_media_dev *imxmd,
+				     struct media_entity *start_entity)
+{
+	struct media_graph graph;
+	struct v4l2_subdev *sd;
+	struct media_pad *pad;
+	int ret;
+
+	ret = media_graph_walk_init(&graph, &imxmd->md);
+	if (ret)
+		return ret;
+
+	/* first try to locate the mipi-csi2 from the video mux */
+	pad = find_pipeline_remote_source_pad(imxmd, &graph, start_entity,
+					      IMX_MEDIA_GRP_ID_VIDMUX);
+	/* if couldn't reach it from there, try from a CSI */
+	if (!pad)
+		pad = find_pipeline_remote_source_pad(imxmd, &graph,
+						      start_entity,
+						      IMX_MEDIA_GRP_ID_CSI);
+	if (pad) {
+		sd = media_entity_to_v4l2_subdev(pad->entity);
+		if (sd->grp_id & IMX_MEDIA_GRP_ID_CSI2) {
+			ret = pad->index - 1; /* found it! */
+			dev_dbg(imxmd->md.dev, "found vc%d from %s\n",
+				ret, start_entity->name);
+			goto cleanup;
+		}
+	}
+
+	ret = -EPIPE;
+
+cleanup:
+	media_graph_walk_cleanup(&graph);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(imx_media_find_mipi_csi2_channel);
+
+/*
+ * Find a subdev reached from the given start entity in the
+ * current pipeline.
+ * Must be called with mdev->graph_mutex held.
+ */
+struct imx_media_subdev *
+imx_media_find_pipeline_subdev(struct imx_media_dev *imxmd,
+			       struct media_entity *start_entity,
+			       u32 grp_id)
+{
+	struct imx_media_subdev *imxsd;
+	struct media_graph graph;
+	struct v4l2_subdev *sd;
+	int ret;
+
+	ret = media_graph_walk_init(&graph, &imxmd->md);
+	if (ret)
+		return ERR_PTR(ret);
+
+	sd = find_pipeline_subdev(imxmd, &graph, start_entity, grp_id);
+	if (!sd) {
+		imxsd = ERR_PTR(-ENODEV);
+		goto cleanup;
+	}
+
+	imxsd = imx_media_find_subdev_by_sd(imxmd, sd);
+cleanup:
+	media_graph_walk_cleanup(&graph);
+	return imxsd;
+}
+EXPORT_SYMBOL_GPL(imx_media_find_pipeline_subdev);
+
+/*
+ * Find a video device reached from the given start entity in the
+ * current pipeline.
+ * Must be called with mdev->graph_mutex held.
+ */
+struct video_device *
+imx_media_find_pipeline_video_device(struct imx_media_dev *imxmd,
+				     struct media_entity *start_entity)
+{
+	struct video_device *vdev;
+	struct media_graph graph;
+	int ret;
+
+	ret = media_graph_walk_init(&graph, &imxmd->md);
+	if (ret)
+		return ERR_PTR(ret);
+
+	vdev = find_pipeline_vdev(imxmd, &graph, start_entity);
+	if (!vdev)
+		vdev = ERR_PTR(-ENODEV);
+
+	media_graph_walk_cleanup(&graph);
+	return vdev;
+}
+EXPORT_SYMBOL_GPL(imx_media_find_pipeline_video_device);
+
+struct imx_media_subdev *
+__imx_media_find_sensor(struct imx_media_dev *imxmd,
+			struct media_entity *start_entity)
+{
+	return imx_media_find_pipeline_subdev(imxmd, start_entity,
+					      IMX_MEDIA_GRP_ID_SENSOR);
+}
+EXPORT_SYMBOL_GPL(__imx_media_find_sensor);
+
+struct imx_media_subdev *
+imx_media_find_sensor(struct imx_media_dev *imxmd,
+		      struct media_entity *start_entity)
+{
+	struct imx_media_subdev *sensor;
+
+	mutex_lock(&imxmd->md.graph_mutex);
+	sensor = __imx_media_find_sensor(imxmd, start_entity);
+	mutex_unlock(&imxmd->md.graph_mutex);
+
+	return sensor;
+}
+EXPORT_SYMBOL_GPL(imx_media_find_sensor);
+
+/*
+ * The subdevs have to be powered on/off, and streaming
+ * enabled/disabled, in a specific sequence.
+ */
+static const u32 stream_on_seq[] = {
+	IMX_MEDIA_GRP_ID_IC_PRPVF,
+	IMX_MEDIA_GRP_ID_IC_PRPENC,
+	IMX_MEDIA_GRP_ID_IC_PRP,
+	IMX_MEDIA_GRP_ID_VDIC,
+	IMX_MEDIA_GRP_ID_CSI2,
+	IMX_MEDIA_GRP_ID_SENSOR,
+	IMX_MEDIA_GRP_ID_VIDMUX,
+	IMX_MEDIA_GRP_ID_CSI,
+};
+
+static const u32 stream_off_seq[] = {
+	IMX_MEDIA_GRP_ID_IC_PRPVF,
+	IMX_MEDIA_GRP_ID_IC_PRPENC,
+	IMX_MEDIA_GRP_ID_IC_PRP,
+	IMX_MEDIA_GRP_ID_VDIC,
+	IMX_MEDIA_GRP_ID_CSI,
+	IMX_MEDIA_GRP_ID_VIDMUX,
+	IMX_MEDIA_GRP_ID_SENSOR,
+	IMX_MEDIA_GRP_ID_CSI2,
+};
+
+#define NUM_STREAM_ENTITIES ARRAY_SIZE(stream_on_seq)
+
+static const u32 power_on_seq[] = {
+	IMX_MEDIA_GRP_ID_CSI2,
+	IMX_MEDIA_GRP_ID_SENSOR,
+	IMX_MEDIA_GRP_ID_VIDMUX,
+	IMX_MEDIA_GRP_ID_CSI,
+	IMX_MEDIA_GRP_ID_VDIC,
+	IMX_MEDIA_GRP_ID_IC_PRPENC,
+	IMX_MEDIA_GRP_ID_IC_PRPVF,
+};
+
+static const u32 power_off_seq[] = {
+	IMX_MEDIA_GRP_ID_IC_PRPVF,
+	IMX_MEDIA_GRP_ID_IC_PRPENC,
+	IMX_MEDIA_GRP_ID_VDIC,
+	IMX_MEDIA_GRP_ID_CSI,
+	IMX_MEDIA_GRP_ID_VIDMUX,
+	IMX_MEDIA_GRP_ID_SENSOR,
+	IMX_MEDIA_GRP_ID_CSI2,
+};
+
+#define NUM_POWER_ENTITIES ARRAY_SIZE(power_on_seq)
+
+static int imx_media_set_stream(struct imx_media_dev *imxmd,
+				struct media_entity *start_entity,
+				bool on)
+{
+	struct media_graph graph;
+	struct v4l2_subdev *sd;
+	int i, ret;
+	u32 id;
+
+	mutex_lock(&imxmd->md.graph_mutex);
+
+	ret = media_graph_walk_init(&graph, &imxmd->md);
+	if (ret)
+		goto unlock;
+
+	for (i = 0; i < NUM_STREAM_ENTITIES; i++) {
+		id = on ? stream_on_seq[i] : stream_off_seq[i];
+		sd = find_pipeline_subdev(imxmd, &graph,
+					  start_entity, id);
+		if (!sd)
+			continue;
+
+		ret = v4l2_subdev_call(sd, video, s_stream, on);
+		if (on && ret && ret != -ENOIOCTLCMD)
+			break;
+	}
+
+	media_graph_walk_cleanup(&graph);
+unlock:
+	mutex_unlock(&imxmd->md.graph_mutex);
+
+	return (on && ret && ret != -ENOIOCTLCMD) ? ret : 0;
+}
+
+/*
+ * Turn current pipeline streaming on/off starting from entity.
+ */
+int imx_media_pipeline_set_stream(struct imx_media_dev *imxmd,
+				  struct media_entity *entity,
+				  struct media_pipeline *pipe,
+				  bool on)
+{
+	int ret = 0;
+
+	if (on) {
+		ret = media_pipeline_start(entity, pipe);
+		if (ret)
+			return ret;
+		ret = imx_media_set_stream(imxmd, entity, true);
+		if (!ret)
+			return 0;
+		/* fall through */
+	}
+
+	imx_media_set_stream(imxmd, entity, false);
+	if (entity->pipe)
+		media_pipeline_stop(entity);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(imx_media_pipeline_set_stream);
+
+static int imx_media_set_power(struct imx_media_dev *imxmd,
+			       struct media_graph *graph,
+			       struct media_entity *start_entity, bool on)
+{
+	struct v4l2_subdev *sd;
+	int i, ret = 0;
+	u32 id;
+
+	for (i = 0; i < NUM_POWER_ENTITIES; i++) {
+		id = on ? power_on_seq[i] : power_off_seq[i];
+		sd = find_pipeline_subdev(imxmd, graph, start_entity, id);
+		if (!sd)
+			continue;
+
+		ret = v4l2_subdev_call(sd, core, s_power, on);
+		if (on && ret && ret != -ENOIOCTLCMD)
+			break;
+	}
+
+	return (on && ret && ret != -ENOIOCTLCMD) ? ret : 0;
+}
+
+/*
+ * Turn current pipeline power on/off starting from start_entity.
+ * Must be called with mdev->graph_mutex held.
+ */
+int imx_media_pipeline_set_power(struct imx_media_dev *imxmd,
+				 struct media_graph *graph,
+				 struct media_entity *start_entity, bool on)
+{
+	int ret;
+
+	ret = imx_media_set_power(imxmd, graph, start_entity, on);
+	if (ret)
+		imx_media_set_power(imxmd, graph, start_entity, false);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(imx_media_pipeline_set_power);
+
+MODULE_DESCRIPTION("i.MX5/6 v4l2 media controller driver");
+MODULE_AUTHOR("Steve Longerbeam <steve_longerbeam@mentor.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/staging/media/imx/imx-media.h b/drivers/staging/media/imx/imx-media.h
new file mode 100644
index 0000000..2dd48ea
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media.h
@@ -0,0 +1,303 @@
+/*
+ * V4L2 Media Controller Driver for Freescale i.MX5/6 SOC
+ *
+ * Copyright (c) 2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#ifndef _IMX_MEDIA_H
+#define _IMX_MEDIA_H
+
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-of.h>
+#include <media/v4l2-subdev.h>
+#include <media/videobuf2-dma-contig.h>
+#include <video/imx-ipu-v3.h>
+
+/*
+ * This is somewhat arbitrary, but we need at least:
+ * - 2 camera interface subdevs
+ * - 3 IC subdevs
+ * - 2 CSI subdevs
+ * - 1 mipi-csi2 receiver subdev
+ * - 2 video-mux subdevs
+ * - 3 camera sensor subdevs (2 parallel, 1 mipi-csi2)
+ *
+ * And double the above numbers for quad i.mx!
+ */
+#define IMX_MEDIA_MAX_SUBDEVS       48
+/* max pads per subdev */
+#define IMX_MEDIA_MAX_PADS          16
+/* max links per pad */
+#define IMX_MEDIA_MAX_LINKS          8
+
+/*
+ * Pad definitions for the subdevs with multiple source or
+ * sink pads
+ */
+/* ipu_csi */
+enum {
+	CSI_SINK_PAD = 0,
+	CSI_SRC_PAD_DIRECT,
+	CSI_SRC_PAD_IDMAC,
+	CSI_NUM_PADS,
+};
+
+#define CSI_NUM_SINK_PADS 1
+#define CSI_NUM_SRC_PADS  2
+
+/* ipu_vdic */
+enum {
+	VDIC_SINK_PAD_DIRECT = 0,
+	VDIC_SINK_PAD_IDMAC,
+	VDIC_SRC_PAD_DIRECT,
+	VDIC_NUM_PADS,
+};
+
+#define VDIC_NUM_SINK_PADS 2
+#define VDIC_NUM_SRC_PADS  1
+
+/* ipu_ic_prp */
+enum {
+	PRP_SINK_PAD = 0,
+	PRP_SRC_PAD_PRPENC,
+	PRP_SRC_PAD_PRPVF,
+	PRP_NUM_PADS,
+};
+
+#define PRP_NUM_SINK_PADS 1
+#define PRP_NUM_SRC_PADS  2
+
+/* ipu_ic_prpencvf */
+enum {
+	PRPENCVF_SINK_PAD = 0,
+	PRPENCVF_SRC_PAD,
+	PRPENCVF_NUM_PADS,
+};
+
+#define PRPENCVF_NUM_SINK_PADS 1
+#define PRPENCVF_NUM_SRC_PADS  1
+
+/* How long to wait for EOF interrupts in the buffer-capture subdevs */
+#define IMX_MEDIA_EOF_TIMEOUT       1000
+
+struct imx_media_pixfmt {
+	u32     fourcc;
+	u32     codes[4];
+	int     bpp;     /* total bpp */
+	enum ipu_color_space cs;
+	bool    planar;  /* is a planar format */
+	bool    ipufmt;  /* is one of the IPU internal formats */
+};
+
+struct imx_media_buffer {
+	struct vb2_v4l2_buffer vbuf; /* v4l buffer must be first */
+	struct list_head  list;
+};
+
+struct imx_media_video_dev {
+	struct video_device *vfd;
+
+	/* the user format */
+	struct v4l2_format fmt;
+	const struct imx_media_pixfmt *cc;
+};
+
+static inline struct imx_media_buffer *to_imx_media_vb(struct vb2_buffer *vb)
+{
+	struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb);
+
+	return container_of(vbuf, struct imx_media_buffer, vbuf);
+}
+
+struct imx_media_link {
+	struct device_node *remote_sd_node;
+	char               remote_devname[32];
+	int                local_pad;
+	int                remote_pad;
+};
+
+struct imx_media_pad {
+	struct media_pad  pad;
+	struct imx_media_link link[IMX_MEDIA_MAX_LINKS];
+	bool devnode; /* does this pad link to a device node */
+	int num_links;
+};
+
+struct imx_media_internal_sd_platformdata {
+	char sd_name[V4L2_SUBDEV_NAME_SIZE];
+	u32 grp_id;
+	int ipu_id;
+};
+
+struct imx_media_subdev {
+	struct v4l2_async_subdev asd;
+	struct v4l2_subdev       *sd; /* set when bound */
+
+	struct imx_media_pad     pad[IMX_MEDIA_MAX_PADS];
+	int num_sink_pads;
+	int num_src_pads;
+
+	/* the platform device if this is an internal subdev */
+	struct platform_device *pdev;
+	/* the devname is needed for async devname match */
+	char devname[32];
+
+	/* if this is a sensor */
+	struct v4l2_of_endpoint sensor_ep;
+};
+
+struct imx_media_dev {
+	struct media_device md;
+	struct v4l2_device  v4l2_dev;
+
+	/* master subdev list */
+	struct imx_media_subdev subdev[IMX_MEDIA_MAX_SUBDEVS];
+	int num_subdevs;
+
+	/* IPUs this media driver control, valid after subdevs bound */
+	struct ipu_soc *ipu[2];
+
+	/* used during link_notify */
+	struct media_graph link_notify_graph;
+
+	/* for async subdev registration */
+	struct v4l2_async_subdev *async_ptrs[IMX_MEDIA_MAX_SUBDEVS];
+	struct v4l2_async_notifier subdev_notifier;
+};
+
+const struct imx_media_pixfmt *imx_media_find_format(u32 fourcc, u32 code,
+						     bool allow_rgb,
+						     bool allow_planar);
+const struct imx_media_pixfmt *imx_media_find_ipu_format(u32 fourcc, u32 code,
+							 bool allow_rgb);
+
+int imx_media_enum_format(u32 *fourcc, u32 *code, u32 index,
+			  bool allow_rgb, bool allow_planar);
+int imx_media_enum_ipu_format(u32 *fourcc, u32 *code, u32 index,
+			      bool allow_rgb);
+
+int imx_media_init_mbus_fmt(struct v4l2_mbus_framefmt *mbus,
+			    u32 width, u32 height, u32 code, u32 field,
+			    const struct imx_media_pixfmt **cc);
+
+int imx_media_mbus_fmt_to_pix_fmt(struct v4l2_pix_format *pix,
+				  struct v4l2_mbus_framefmt *mbus,
+				  const struct imx_media_pixfmt *cc);
+int imx_media_mbus_fmt_to_ipu_image(struct ipu_image *image,
+				    struct v4l2_mbus_framefmt *mbus);
+int imx_media_ipu_image_to_mbus_fmt(struct v4l2_mbus_framefmt *mbus,
+				    struct ipu_image *image);
+
+struct imx_media_subdev *
+imx_media_find_async_subdev(struct imx_media_dev *imxmd,
+			    struct device_node *np,
+			    const char *devname);
+struct imx_media_subdev *
+imx_media_add_async_subdev(struct imx_media_dev *imxmd,
+			   struct device_node *np,
+			   struct platform_device *pdev);
+int imx_media_add_pad_link(struct imx_media_dev *imxmd,
+			   struct imx_media_pad *pad,
+			   struct device_node *remote_node,
+			   const char *remote_devname,
+			   int local_pad, int remote_pad);
+
+void imx_media_grp_id_to_sd_name(char *sd_name, int sz,
+				 u32 grp_id, int ipu_id);
+
+int imx_media_add_internal_subdevs(struct imx_media_dev *imxmd,
+				   struct imx_media_subdev *csi[4]);
+void imx_media_remove_internal_subdevs(struct imx_media_dev *imxmd);
+
+struct imx_media_subdev *
+imx_media_find_subdev_by_sd(struct imx_media_dev *imxmd,
+			    struct v4l2_subdev *sd);
+struct imx_media_subdev *
+imx_media_find_subdev_by_id(struct imx_media_dev *imxmd,
+			    u32 grp_id);
+int imx_media_find_mipi_csi2_channel(struct imx_media_dev *imxmd,
+				     struct media_entity *start_entity);
+struct imx_media_subdev *
+imx_media_find_pipeline_subdev(struct imx_media_dev *imxmd,
+			       struct media_entity *start_entity,
+			       u32 grp_id);
+struct video_device *
+imx_media_find_pipeline_video_device(struct imx_media_dev *imxmd,
+				     struct media_entity *start_entity);
+struct imx_media_subdev *
+__imx_media_find_sensor(struct imx_media_dev *imxmd,
+			struct media_entity *start_entity);
+struct imx_media_subdev *
+imx_media_find_sensor(struct imx_media_dev *imxmd,
+		      struct media_entity *start_entity);
+
+struct imx_media_dma_buf {
+	void          *virt;
+	dma_addr_t     phys;
+	unsigned long  len;
+};
+
+void imx_media_free_dma_buf(struct imx_media_dev *imxmd,
+			    struct imx_media_dma_buf *buf);
+int imx_media_alloc_dma_buf(struct imx_media_dev *imxmd,
+			    struct imx_media_dma_buf *buf,
+			    int size);
+
+int imx_media_pipeline_set_power(struct imx_media_dev *imxmd,
+				 struct media_graph *graph,
+				 struct media_entity *entity, bool on);
+int imx_media_pipeline_set_stream(struct imx_media_dev *imxmd,
+				  struct media_entity *entity,
+				  struct media_pipeline *pipe,
+				  bool on);
+
+/* imx-media-fim.c */
+struct imx_media_fim;
+void imx_media_fim_eof_monitor(struct imx_media_fim *fim, struct timespec *ts);
+int imx_media_fim_set_power(struct imx_media_fim *fim, bool on);
+int imx_media_fim_set_stream(struct imx_media_fim *fim,
+			     struct imx_media_subdev *sensor,
+			     bool on);
+struct imx_media_fim *imx_media_fim_init(struct v4l2_subdev *sd);
+void imx_media_fim_free(struct imx_media_fim *fim);
+
+/* imx-media-of.c */
+struct imx_media_subdev *
+imx_media_of_find_subdev(struct imx_media_dev *imxmd,
+			 struct device_node *np,
+			 const char *name);
+int imx_media_of_parse(struct imx_media_dev *dev,
+		       struct imx_media_subdev *(*csi)[4],
+		       struct device_node *np);
+
+/* imx-media-capture.c */
+struct imx_media_video_dev *
+imx_media_capture_device_init(struct v4l2_subdev *src_sd, int pad);
+void imx_media_capture_device_remove(struct imx_media_video_dev *vdev);
+int imx_media_capture_device_register(struct imx_media_video_dev *vdev);
+void imx_media_capture_device_unregister(struct imx_media_video_dev *vdev);
+struct imx_media_buffer *
+imx_media_capture_device_next_buf(struct imx_media_video_dev *vdev);
+void imx_media_capture_device_set_format(struct imx_media_video_dev *vdev,
+					 struct v4l2_pix_format *pix);
+void imx_media_capture_device_error(struct imx_media_video_dev *vdev);
+
+/* subdev group ids */
+#define IMX_MEDIA_GRP_ID_SENSOR    (1 << 8)
+#define IMX_MEDIA_GRP_ID_VIDMUX    (1 << 9)
+#define IMX_MEDIA_GRP_ID_CSI2      (1 << 10)
+#define IMX_MEDIA_GRP_ID_CSI_BIT   11
+#define IMX_MEDIA_GRP_ID_CSI       (0x3 << IMX_MEDIA_GRP_ID_CSI_BIT)
+#define IMX_MEDIA_GRP_ID_CSI0      (1 << IMX_MEDIA_GRP_ID_CSI_BIT)
+#define IMX_MEDIA_GRP_ID_CSI1      (2 << IMX_MEDIA_GRP_ID_CSI_BIT)
+#define IMX_MEDIA_GRP_ID_VDIC      (1 << 13)
+#define IMX_MEDIA_GRP_ID_IC_PRP    (1 << 14)
+#define IMX_MEDIA_GRP_ID_IC_PRPENC (1 << 15)
+#define IMX_MEDIA_GRP_ID_IC_PRPVF  (1 << 16)
+
+#endif
diff --git a/include/media/imx.h b/include/media/imx.h
new file mode 100644
index 0000000..5025a72
--- /dev/null
+++ b/include/media/imx.h
@@ -0,0 +1,15 @@
+/*
+ * Copyright (c) 2014-2015 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version
+ */
+
+#ifndef __MEDIA_IMX_H__
+#define __MEDIA_IMX_H__
+
+#include <uapi/media/imx.h>
+
+#endif
diff --git a/include/uapi/linux/v4l2-controls.h b/include/uapi/linux/v4l2-controls.h
index 0d2e1e0..6c29f42 100644
--- a/include/uapi/linux/v4l2-controls.h
+++ b/include/uapi/linux/v4l2-controls.h
@@ -180,6 +180,10 @@ enum v4l2_colorfx {
  * We reserve 16 controls for this driver. */
 #define V4L2_CID_USER_TC358743_BASE		(V4L2_CID_USER_BASE + 0x1080)
 
+/* The base for the imx driver controls.
+ * We reserve 16 controls for this driver. */
+#define V4L2_CID_USER_IMX_BASE			(V4L2_CID_USER_BASE + 0x1090)
+
 /* MPEG-class control IDs */
 /* The MPEG controls are applicable to all codec controls
  * and the 'MPEG' part of the define is historical */
-- 
2.7.4

[PATCH v5 23/39] media: Add i.MX media core driver

[Steve Longerbeam]

Add the core media driver for i.MX SOC.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 Documentation/media/v4l-drivers/imx.rst           | 560 ++++++++++++++++
 drivers/staging/media/Kconfig                     |   2 +
 drivers/staging/media/Makefile                    |   1 +
 drivers/staging/media/imx/Kconfig                 |   6 +
 drivers/staging/media/imx/Makefile                |   5 +
 drivers/staging/media/imx/TODO                    |  17 +
 drivers/staging/media/imx/imx-media-dev.c         | 522 +++++++++++++++
 drivers/staging/media/imx/imx-media-fim.c         | 471 +++++++++++++
 drivers/staging/media/imx/imx-media-internal-sd.c | 349 ++++++++++
 drivers/staging/media/imx/imx-media-of.c          | 267 ++++++++
 drivers/staging/media/imx/imx-media-utils.c       | 766 ++++++++++++++++++++++
 drivers/staging/media/imx/imx-media.h             | 303 +++++++++
 include/media/imx.h                               |  15 +
 include/uapi/linux/v4l2-controls.h                |   4 +
 14 files changed, 3288 insertions(+)
 create mode 100644 Documentation/media/v4l-drivers/imx.rst
 create mode 100644 drivers/staging/media/imx/Kconfig
 create mode 100644 drivers/staging/media/imx/Makefile
 create mode 100644 drivers/staging/media/imx/TODO
 create mode 100644 drivers/staging/media/imx/imx-media-dev.c
 create mode 100644 drivers/staging/media/imx/imx-media-fim.c
 create mode 100644 drivers/staging/media/imx/imx-media-internal-sd.c
 create mode 100644 drivers/staging/media/imx/imx-media-of.c
 create mode 100644 drivers/staging/media/imx/imx-media-utils.c
 create mode 100644 drivers/staging/media/imx/imx-media.h
 create mode 100644 include/media/imx.h

diff --git a/Documentation/media/v4l-drivers/imx.rst b/Documentation/media/v4l-drivers/imx.rst
new file mode 100644
index 0000000..443e0d0
--- /dev/null
+++ b/Documentation/media/v4l-drivers/imx.rst
@@ -0,0 +1,560 @@
+i.MX Video Capture Driver
+=========================
+
+Introduction
+------------
+
+The Freescale i.MX5/6 contains an Image Processing Unit (IPU), which
+handles the flow of image frames to and from capture devices and
+display devices.
+
+For image capture, the IPU contains the following internal subunits:
+
+- Image DMA Controller (IDMAC)
+- Camera Serial Interface (CSI)
+- Image Converter (IC)
+- Sensor Multi-FIFO Controller (SMFC)
+- Image Rotator (IRT)
+- Video De-Interlacing or Combining Block (VDIC)
+
+The IDMAC is the DMA controller for transfer of image frames to and from
+memory. Various dedicated DMA channels exist for both video capture and
+display paths. During transfer, the IDMAC is also capable of vertical
+image flip, 8x8 block transfer (see IRT description), pixel component
+re-ordering (for example UYVY to YUYV) within the same colorspace, and
+even packed <--> planar conversion. It can also perform a simple
+de-interlacing by interleaving even and odd lines during transfer
+(without motion compensation which requires the VDIC).
+
+The CSI is the backend capture unit that interfaces directly with
+camera sensors over Parallel, BT.656/1120, and MIPI CSI-2 busses.
+
+The IC handles color-space conversion, resizing (downscaling and
+upscaling), horizontal flip, and 90/270 degree rotation operations.
+
+There are three independent "tasks" within the IC that can carry out
+conversions concurrently: pre-process encoding, pre-process viewfinder,
+and post-processing. Within each task, conversions are split into three
+sections: downsizing section, main section (upsizing, flip, colorspace
+conversion, and graphics plane combining), and rotation section.
+
+The IPU time-shares the IC task operations. The time-slice granularity
+is one burst of eight pixels in the downsizing section, one image line
+in the main processing section, one image frame in the rotation section.
+
+The SMFC is composed of four independent FIFOs that each can transfer
+captured frames from sensors directly to memory concurrently via four
+IDMAC channels.
+
+The IRT carries out 90 and 270 degree image rotation operations. The
+rotation operation is carried out on 8x8 pixel blocks at a time. This
+operation is supported by the IDMAC which handles the 8x8 block transfer
+along with block reordering, in coordination with vertical flip.
+
+The VDIC handles the conversion of interlaced video to progressive, with
+support for different motion compensation modes (low, medium, and high
+motion). The deinterlaced output frames from the VDIC can be sent to the
+IC pre-process viewfinder task for further conversions. The VDIC also
+contains a Combiner that combines two image planes, with alpha blending
+and color keying.
+
+In addition to the IPU internal subunits, there are also two units
+outside the IPU that are also involved in video capture on i.MX:
+
+- MIPI CSI-2 Receiver for camera sensors with the MIPI CSI-2 bus
+  interface. This is a Synopsys DesignWare core.
+- Two video multiplexers for selecting among multiple sensor inputs
+  to send to a CSI.
+
+For more info, refer to the latest versions of the i.MX5/6 reference
+manuals listed under References.
+
+
+Features
+--------
+
+Some of the features of this driver include:
+
+- Many different pipelines can be configured via media controller API,
+  that correspond to the hardware video capture pipelines supported in
+  the i.MX.
+
+- Supports parallel, BT.565, and MIPI CSI-2 interfaces.
+
+- Up to four concurrent sensor acquisitions, by configuring each
+  sensor's pipeline using independent entities. This is currently
+  demonstrated with the SabreSD and SabreLite reference boards with
+  independent OV5642 and MIPI CSI-2 OV5640 sensor modules.
+
+- Scaling, color-space conversion, horizontal and vertical flip, and
+  image rotation via IC task subdevs.
+
+- Many pixel formats supported (RGB, packed and planar YUV, partial
+  planar YUV).
+
+- The VDIC subdev supports motion compensated de-interlacing, with three
+  motion compensation modes: low, medium, and high motion. Pipelines are
+  defined that allow sending frames to the VDIC subdev directly from the
+  CSI or from memory buffers via an output/mem2mem device node. For low
+  and medium motion modes, the VDIC must receive from memory buffers via
+  a device node.
+
+- Includes a Frame Interval Monitor (FIM) that can correct vertical sync
+  problems with the ADV718x video decoders. See below for a description
+  of the FIM.
+
+
+Entities
+--------
+
+imx6-mipi-csi2
+--------------
+
+This is the MIPI CSI-2 receiver entity. It has one sink pad to receive
+the MIPI CSI-2 stream (usually from a MIPI CSI-2 camera sensor). It has
+four source pads, corresponding to the four MIPI CSI-2 demuxed virtual
+channel outputs.
+
+This entity actually consists of two sub-blocks. One is the MIPI CSI-2
+core. This is a Synopsys Designware MIPI CSI-2 core. The other sub-block
+is a "CSI-2 to IPU gasket". The gasket acts as a demultiplexer of the
+four virtual channels streams, providing four separate parallel buses
+containing each virtual channel that are routed to CSIs or video
+multiplexers as described below.
+
+On i.MX6 solo/dual-lite, all four virtual channel buses are routed to
+two video multiplexers. Both CSI0 and CSI1 can receive any virtual
+channel, as selected by the video multiplexers.
+
+On i.MX6 Quad, virtual channel 0 is routed to IPU1-CSI0 (after selected
+by a video mux), virtual channels 1 and 2 are hard-wired to IPU1-CSI1
+and IPU2-CSI0, respectively, and virtual channel 3 is routed to
+IPU2-CSI1 (again selected by a video mux).
+
+ipuX_csiY_mux
+-------------
+
+These are the video multiplexers. They have two or more sink pads to
+select from either camera sensors with a parallel interface, or from
+MIPI CSI-2 virtual channels from imx6-mipi-csi2 entity. They have a
+single source pad that routes to a CSI (ipuX_csiY entities).
+
+On i.MX6 solo/dual-lite, there are two video mux entities. One sits
+in front of IPU1-CSI0 to select between a parallel sensor and any of
+the four MIPI CSI-2 virtual channels (a total of five sink pads). The
+other mux sits in front of IPU1-CSI1, and again has five sink pads to
+select between a parallel sensor and any of the four MIPI CSI-2 virtual
+channels.
+
+On i.MX6 Quad, there are two video mux entities. One sits in front of
+IPU1-CSI0 to select between a parallel sensor and MIPI CSI-2 virtual
+channel 0 (two sink pads). The other mux sits in front of IPU2-CSI1 to
+select between a parallel sensor and MIPI CSI-2 virtual channel 3 (two
+sink pads).
+
+ipuX_csiY
+---------
+
+These are the CSI entities. They have a single sink pad receiving from
+either a video mux or from a MIPI CSI-2 virtual channel as described
+above.
+
+This entity has two source pads. The first source pad can link directly
+to the ipuX_vdic entity or the ipuX_ic_prp entity, using hardware links
+that require no IDMAC memory buffer transfer.
+
+When the direct source pad is routed to the ipuX_ic_prp entity, frames
+from the CSI will be processed by one of the IC pre-processing tasks.
+
+When the direct source pad is routed to the ipuX_vdic entity, the VDIC
+will carry out motion-compensated de-interlace using "high motion" mode
+(see description of ipuX_vdic entity).
+
+The second source pad sends video frames to memory buffers via the SMFC
+and an IDMAC channel. This source pad is routed to a capture device
+node.
+
+Note that since the IDMAC source pad makes use of an IDMAC channel, it
+can do pixel reordering within the same colorspace. For example, the
+sink pad can take UYVY2X8, but the IDMAC source pad can output YUYV2X8.
+If the sink pad is receiving YUV, the output at the capture device can
+also be converted to a planar YUV format such as YUV420.
+
+It will also perform simple de-interlace without motion compensation,
+which is activated if the sink pad's field type is an interlaced type,
+and the IDMAC source pad field type is set to none.
+
+This subdev can generate two types of events:
+
+- V4L2_EVENT_NEW_FRAME_BEFORE_EOF
+- V4L2_EVENT_FRAME_INTERVAL_ERROR
+
+The user application can subscribe to these events from the ipuX_csiY
+subdev node. The V4L2_EVENT_FRAME_INTERVAL_ERROR event is generated
+by the Frame Interval Monitor (see below for more on the FIM).
+
+ipuX_vdic
+---------
+
+The VDIC carries out motion compensated de-interlacing, with three
+motion compensation modes: low, medium, and high motion. The mode is
+specified with the menu control V4L2_CID_DEINTERLACING_MODE. It has
+two sink pads and a single source pad.
+
+The direct sink pad receives from an ipuX_csiY direct pad. With this
+link the VDIC can only operate in high motion mode.
+
+When the IDMAC sink pad is activated, it receives from an output
+or mem2mem device node. With this pipeline, it can also operate
+in low and medium modes, because these modes require receiving
+frames from memory buffers. Note that an output or mem2mem device
+is not implemented yet, so this sink pad currently has no links.
+
+The source pad routes to the IC pre-processing entity ipuX_ic_prp.
+
+ipuX_ic_prp
+-----------
+
+This is the IC pre-processing entity. It acts as a router, routing
+data from its sink pad to one or both of its source pads.
+
+It has a single sink pad. The sink pad can receive from the ipuX_csiY
+direct pad, or from ipuX_vdic.
+
+This entity has two source pads. One source pad routes to the
+pre-process encode task entity (ipuX_ic_prpenc), the other to the
+pre-process viewfinder task entity (ipuX_ic_prpvf). Both source pads
+can be activated at the same time if the sink pad is receiving from
+ipuX_csiY. Only the source pad to the pre-process viewfinder task entity
+can be activated if the sink pad is receiving from ipuX_vdic (frames
+from the VDIC can only be processed by the pre-process viewfinder task).
+
+ipuX_ic_prpenc
+--------------
+
+This is the IC pre-processing encode entity. It has a single sink pad
+from ipuX_ic_prp, and a single source pad. The source pad is routed
+to a capture device node.
+
+This entity performs the IC pre-process encode task operations:
+color-space conversion, resizing (downscaling and upscaling), horizontal
+and vertical flip, and 90/270 degree rotation.
+
+Like the ipuX_csiY IDMAC source, it can also perform simple de-interlace
+without motion compensation, and pixel reordering.
+
+This subdev can generate the V4L2_EVENT_NEW_FRAME_BEFORE_EOF event, and
+can be subscribed to from the ipuX_ic_prpenc subdev node.
+
+ipuX_ic_prpvf
+-------------
+
+This is the IC pre-processing viewfinder entity. It has a single sink pad
+from ipuX_ic_prp, and a single source pad. The source pad is routed to
+a capture device node.
+
+It is identical in operation to ipuX_ic_prpenc. It will receive and
+process de-interlaced frames from the ipuX_vdic if ipuX_ic_prp is
+receiving from ipuX_vdic.
+
+Like the ipuX_csiY IDMAC source, it can perform simple de-interlace
+without motion compensation. However, note that if the ipuX_vdic is
+included in the pipeline (ipuX_ic_prp is receiving from ipuX_vdic),
+it's not possible to use simple de-interlace in ipuX_ic_prpvf, since
+the ipuX_vdic has already carried out de-interlacing (with motion
+compensation) and therefore the field type output from ipuX_ic_prp can
+only be none.
+
+This subdev can generate the V4L2_EVENT_NEW_FRAME_BEFORE_EOF event, and
+can be subscribed to from the ipuX_ic_prpvf subdev node.
+
+Capture Pipelines
+-----------------
+
+The following describe the various use-cases supported by the pipelines.
+
+The links shown do not include the backend sensor, video mux, or mipi
+csi-2 receiver links. This depends on the type of sensor interface
+(parallel or mipi csi-2). So in all cases, these pipelines begin with:
+
+sensor -> ipuX_csiY_mux -> ...
+
+for parallel sensors, or:
+
+sensor -> imx6-mipi-csi2 -> (ipuX_csiY_mux) -> ...
+
+for mipi csi-2 sensors. The imx6-mipi-csi2 receiver may need to route
+to the video mux (ipuX_csiY_mux) before sending to the CSI, depending
+on the mipi csi-2 virtual channel, hence ipuX_csiY_mux is shown in
+parenthesis.
+
+Unprocessed Video Capture:
+--------------------------
+
+Send frames directly from sensor to camera device interface node, with
+no conversions:
+
+-> ipuX_csiY IDMAC pad -> capture node
+
+IC Direct Conversions:
+----------------------
+
+This pipeline uses the preprocess encode entity to route frames directly
+from the CSI to the IC, to carry out scaling up to 1024x1024 resolution,
+CSC, flipping, and image rotation:
+
+-> ipuX_csiY direct pad -> ipuX_ic_prp -> ipuX_ic_prpenc -> capture node
+
+Motion Compensated De-interlace:
+--------------------------------
+
+This pipeline routes frames from the CSI direct pad to the VDIC entity to
+support motion-compensated de-interlacing (high motion mode only),
+scaling up to 1024x1024, CSC, flip, and rotation:
+
+-> ipuX_csiY direct pad -> ipuX_vdic direct pad -> ipuX_ic_prp ->
+   ipuX_ic_prpvf -> capture node
+
+
+Usage Notes
+-----------
+
+Many of the subdevs require information from the active sensor in the
+current pipeline when configuring pad formats. Therefore the media links
+should be established before configuring the media pad formats.
+
+Similarly, the capture device interfaces inherit controls from the
+active entities in the current pipeline at link-setup time. Therefore
+the capture device node links should be the last links established in
+order for the capture interfaces to "see" and inherit all possible
+controls.
+
+The following are usage notes for Sabre- reference platforms:
+
+
+SabreLite with OV5642 and OV5640
+--------------------------------
+
+This platform requires the OmniVision OV5642 module with a parallel
+camera interface, and the OV5640 module with a MIPI CSI-2
+interface. Both modules are available from Boundary Devices:
+
+https://boundarydevices.com/products/nit6x_5mp
+https://boundarydevices.com/product/nit6x_5mp_mipi
+
+Note that if only one camera module is available, the other sensor
+node can be disabled in the device tree.
+
+The OV5642 module is connected to the parallel bus input on the i.MX
+internal video mux to IPU1 CSI0. It's i2c bus connects to i2c bus 2.
+
+The MIPI CSI-2 OV5640 module is connected to the i.MX internal MIPI CSI-2
+receiver, and the four virtual channel outputs from the receiver are
+routed as follows: vc0 to the IPU1 CSI0 mux, vc1 directly to IPU1 CSI1,
+vc2 directly to IPU2 CSI0, and vc3 to the IPU2 CSI1 mux. The OV5640 is
+also connected to i2c bus 2 on the SabreLite, therefore the OV5642 and
+OV5640 must not share the same i2c slave address.
+
+The following basic example configures unprocessed video capture
+pipelines for both sensors. The OV5642 is routed to ipu1_csi0, and
+the OV5640 (transmitting on mipi csi-2 virtual channel 1) is routed
+to ipu1_csi1. Both sensors are configured to output 640x480, the
+OV5642 outputs YUYV2X8, the OV5640 UYVY2X8:
+
+.. code-block:: none
+
+   # Setup links for OV5642
+   media-ctl -l '"ov5642 1-0042":0 -> "ipu1_csi0_mux":1[1]'
+   media-ctl -l '"ipu1_csi0_mux":2 -> "ipu1_csi0":0[1]'
+   media-ctl -l '"ipu1_csi0":2 -> "ipu1_csi0 capture":0[1]'
+   # Setup links for OV5640
+   media-ctl -l '"ov5640 1-0040":0 -> "imx6-mipi-csi2":0[1]'
+   media-ctl -l '"imx6-mipi-csi2":2 -> "ipu1_csi1":0[1]'
+   media-ctl -l '"ipu1_csi1":2 -> "ipu1_csi1 capture":0[1]'
+   # Configure pads for OV5642 pipeline
+   media-ctl -V "\"ov5642 1-0042\":0 [fmt:YUYV2X8/640x480 field:none]"
+   media-ctl -V "\"ipu1_csi0_mux\":2 [fmt:YUYV2X8/640x480 field:none]"
+   media-ctl -V "\"ipu1_csi0\":2 [fmt:AYUV32/640x480 field:none]"
+   # Configure pads for OV5640 pipeline
+   media-ctl -V "\"ov5640 1-0040\":0 [fmt:UYVY2X8/640x480 field:none]"
+   media-ctl -V "\"imx6-mipi-csi2\":2 [fmt:UYVY2X8/640x480 field:none]"
+   media-ctl -V "\"ipu1_csi1\":2 [fmt:AYUV32/640x480 field:none]"
+
+Streaming can then begin independently on the capture device nodes
+"ipu1_csi0 capture" and "ipu1_csi1 capture". The v4l2-ctl tool can
+be used to select any supported YUV pixelformat on the capture device
+nodes, including planar.
+
+SabreAuto with ADV7180 decoder
+------------------------------
+
+On the SabreAuto, an on-board ADV7180 SD decoder is connected to the
+parallel bus input on the internal video mux to IPU1 CSI0.
+
+The following example configures a pipeline to capture from the ADV7180
+video decoder, assuming NTSC 720x480 input signals, with Motion
+Compensated de-interlacing. Pad field types assume the adv7180 outputs
+"alternate", which the ipu1_csi0 entity converts to "seq-tb" at its
+source pad. $outputfmt can be any format supported by the ipu1_ic_prpvf
+entity at its output pad:
+
+.. code-block:: none
+
+   # Setup links
+   media-ctl -l '"adv7180 4-0021":0 -> "ipu1_csi0_mux":1[1]'
+   media-ctl -l '"ipu1_csi0_mux":2 -> "ipu1_csi0":0[1]'
+   media-ctl -l '"ipu1_csi0":1 -> "ipu1_vdic":0[1]'
+   media-ctl -l '"ipu1_vdic":2 -> "ipu1_ic_prp":0[1]'
+   media-ctl -l '"ipu1_ic_prp":2 -> "ipu1_ic_prpvf":0[1]'
+   media-ctl -l '"ipu1_ic_prpvf":1 -> "ipu1_ic_prpvf capture":0[1]'
+   # Configure pads
+   media-ctl -V "\"adv7180 4-0021\":0 [fmt:UYVY2X8/720x480]"
+   media-ctl -V "\"ipu1_csi0_mux\":2 [fmt:UYVY2X8/720x480 field:alternate]"
+   media-ctl -V "\"ipu1_csi0\":1 [fmt:AYUV32/720x480 field:seq-tb]"
+   media-ctl -V "\"ipu1_vdic\":2 [fmt:AYUV32/720x480 field:none]"
+   media-ctl -V "\"ipu1_ic_prp\":2 [fmt:AYUV32/720x480 field:none]"
+   media-ctl -V "\"ipu1_ic_prpvf\":1 [fmt:$outputfmt field:none]"
+
+Streaming can then begin on the capture device node at
+"ipu1_ic_prpvf capture". The v4l2-ctl tool can be used to select any
+supported YUV or RGB pixelformat on the capture device node.
+
+This platform accepts Composite Video analog inputs to the ADV7180 on
+Ain1 (connector J42).
+
+Frame Interval Monitor
+----------------------
+
+The adv718x decoders can occasionally send corrupt fields during
+NTSC/PAL signal re-sync (too little or too many video lines). When
+this happens, the IPU triggers a mechanism to re-establish vertical
+sync by adding 1 dummy line every frame, which causes a rolling effect
+from image to image, and can last a long time before a stable image is
+recovered. Or sometimes the mechanism doesn't work at all, causing a
+permanent split image (one frame contains lines from two consecutive
+captured images).
+
+From experiment it was found that during image rolling, the frame
+intervals (elapsed time between two EOF's) drop below the nominal
+value for the current standard, by about one frame time (60 usec),
+and remain at that value until rolling stops.
+
+While the reason for this observation isn't known (the IPU dummy
+line mechanism should show an increase in the intervals by 1 line
+time every frame, not a fixed value), we can use it to detect the
+corrupt fields using a frame interval monitor. If the FIM detects a
+bad frame interval, a subdev event is sent. In response, userland can
+issue a streaming restart to correct the rolling/split image.
+
+The FIM is implemented in the ipuX_csiY entity, and the entities that
+generate End-Of-Frame interrupts call into the FIM to monitor the frame
+intervals: ipuX_ic_prpenc, and ipuX_ic_prpvf. Userland can register with
+the FIM event notifications on the ipuX_csiY subdev device node
+(V4L2_EVENT_FRAME_INTERVAL_ERROR).
+
+The ipuX_csiY entity includes custom controls to tweak some dials for
+FIM. If one of these controls is changed during streaming, the FIM will
+be reset and will continue at the new settings.
+
+- V4L2_CID_IMX_FIM_ENABLE
+
+Enable/disable the FIM.
+
+- V4L2_CID_IMX_FIM_NUM
+
+How many frame interval errors to average before comparing against the
+nominal frame interval reported by the sensor. This can reduce noise
+from interrupt latency.
+
+- V4L2_CID_IMX_FIM_TOLERANCE_MIN
+
+If the averaged intervals fall outside nominal by this amount, in
+microseconds, streaming will be restarted.
+
+- V4L2_CID_IMX_FIM_TOLERANCE_MAX
+
+If any interval errors are higher than this value, those error samples
+are discarded and do not enter into the average. This can be used to
+discard really high interval errors that might be due to very high
+system load, causing excessive interrupt latencies.
+
+- V4L2_CID_IMX_FIM_NUM_SKIP
+
+How many frames to skip after a FIM reset or stream restart before
+FIM begins to average intervals. It has been found that there can
+be a few bad frame intervals after stream restart which are not
+attributed to adv718x sending a corrupt field, so this is used to
+skip those frames to prevent unnecessary restarts.
+
+
+SabreSD with MIPI CSI-2 OV5640
+------------------------------
+
+Similarly to SabreLite, the SabreSD supports a parallel interface
+OV5642 module on IPU1 CSI0, and a MIPI CSI-2 OV5640 module. The OV5642
+connects to i2c bus 1 and the OV5640 to i2c bus 2.
+
+The device tree for SabreSD includes OF graphs for both the parallel
+OV5642 and the MIPI CSI-2 OV5640, but as of this writing only the MIPI
+CSI-2 OV5640 has been tested, so the OV5642 node is currently disabled.
+The OV5640 module connects to MIPI connector J5 (sorry I don't have the
+compatible module part number or URL).
+
+The following example configures a direct conversion pipeline to capture
+from the OV5640. $sensorfmt can be any format supported by the OV5640.
+$sensordim is the frame dimension part of $sensorfmt (minus the mbus
+pixel code). $outputfmt can be any format supported by the
+ipu1_ic_prpenc entity at its output pad:
+
+.. code-block:: none
+
+   # Setup links
+   media-ctl -l '"ov5640 1-003c":0 -> "imx6-mipi-csi2":0[1]'
+   media-ctl -l '"imx6-mipi-csi2":2 -> "ipu1_csi1":0[1]'
+   media-ctl -l '"ipu1_csi1":1 -> "ipu1_ic_prp":0[1]'
+   media-ctl -l '"ipu1_ic_prp":1 -> "ipu1_ic_prpenc":0[1]'
+   media-ctl -l '"ipu1_ic_prpenc":1 -> "ipu1_ic_prpenc capture":0[1]'
+   # Configure pads
+   media-ctl -V "\"ov5640 1-003c\":0 [fmt:$sensorfmt field:none]"
+   media-ctl -V "\"imx6-mipi-csi2\":2 [fmt:$sensorfmt field:none]"
+   media-ctl -V "\"ipu1_csi1\":1 [fmt:AYUV32/$sensordim field:none]"
+   media-ctl -V "\"ipu1_ic_prp\":1 [fmt:AYUV32/$sensordim field:none]"
+   media-ctl -V "\"ipu1_ic_prpenc\":1 [fmt:$outputfmt field:none]"
+
+Streaming can then begin on "ipu1_ic_prpenc capture" node. The v4l2-ctl
+tool can be used to select any supported YUV or RGB pixelformat on the
+capture device node.
+
+
+Known Issues
+------------
+
+1. When using 90 or 270 degree rotation control at capture resolutions
+   near the IC resizer limit of 1024x1024, and combined with planar
+   pixel formats (YUV420, YUV422p), frame capture will often fail with
+   no end-of-frame interrupts from the IDMAC channel. To work around
+   this, use lower resolution and/or packed formats (YUYV, RGB3, etc.)
+   when 90 or 270 rotations are needed.
+
+
+File list
+---------
+
+drivers/staging/media/imx/
+include/media/imx.h
+include/uapi/media/imx.h
+
+References
+----------
+
+[1] "i.MX 6Dual/6Quad Applications Processor Reference Manual"
+[2] "i.MX 6Solo/6DualLite Applications Processor Reference Manual"
+
+
+Authors
+-------
+Steve Longerbeam <steve_longerbeam@mentor.com>
+Philipp Zabel <kernel@pengutronix.de>
+Russell King <linux@armlinux.org.uk>
+
+Copyright (C) 2012-2017 Mentor Graphics Inc.
diff --git a/drivers/staging/media/Kconfig b/drivers/staging/media/Kconfig
index abd0e2d..31af2a0 100644
--- a/drivers/staging/media/Kconfig
+++ b/drivers/staging/media/Kconfig
@@ -25,6 +25,8 @@ source "drivers/staging/media/cxd2099/Kconfig"
 
 source "drivers/staging/media/davinci_vpfe/Kconfig"
 
+source "drivers/staging/media/imx/Kconfig"
+
 source "drivers/staging/media/omap4iss/Kconfig"
 
 source "drivers/staging/media/platform/bcm2835/Kconfig"
diff --git a/drivers/staging/media/Makefile b/drivers/staging/media/Makefile
index dc89325..0bfb65d 100644
--- a/drivers/staging/media/Makefile
+++ b/drivers/staging/media/Makefile
@@ -1,6 +1,7 @@
 obj-$(CONFIG_I2C_BCM2048)	+= bcm2048/
 obj-$(CONFIG_VIDEO_SAMSUNG_S5P_CEC) += s5p-cec/
 obj-$(CONFIG_DVB_CXD2099)	+= cxd2099/
+obj-$(CONFIG_VIDEO_IMX_MEDIA)	+= imx/
 obj-$(CONFIG_LIRC_STAGING)	+= lirc/
 obj-$(CONFIG_VIDEO_BCM2835)	+= platform/bcm2835/
 obj-$(CONFIG_VIDEO_DM365_VPFE)	+= davinci_vpfe/
diff --git a/drivers/staging/media/imx/Kconfig b/drivers/staging/media/imx/Kconfig
new file mode 100644
index 0000000..62a3c34
--- /dev/null
+++ b/drivers/staging/media/imx/Kconfig
@@ -0,0 +1,6 @@
+config VIDEO_IMX_MEDIA
+	tristate "i.MX5/6 V4L2 media core driver"
+	depends on MEDIA_CONTROLLER && VIDEO_V4L2 && ARCH_MXC && IMX_IPUV3_CORE
+	---help---
+	  Say yes here to enable support for video4linux media controller
+	  driver for the i.MX5/6 SOC.
diff --git a/drivers/staging/media/imx/Makefile b/drivers/staging/media/imx/Makefile
new file mode 100644
index 0000000..ddd7d94
--- /dev/null
+++ b/drivers/staging/media/imx/Makefile
@@ -0,0 +1,5 @@
+imx-media-objs := imx-media-dev.o imx-media-internal-sd.o imx-media-of.o
+imx-media-common-objs := imx-media-utils.o imx-media-fim.o
+
+obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media.o
+obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-common.o
diff --git a/drivers/staging/media/imx/TODO b/drivers/staging/media/imx/TODO
new file mode 100644
index 0000000..78f78fa
--- /dev/null
+++ b/drivers/staging/media/imx/TODO
@@ -0,0 +1,17 @@
+
+- Finish v4l2-compliance
+
+- Clean up and move the ov5642 subdev driver to drivers/media/i2c, and
+  create the binding docs for it.
+
+- The Frame Interval Monitor could be exported to v4l2-core for
+  general use.
+
+- At driver load time, the device-tree node that is the original source
+  (the "sensor"), is parsed to record its media bus configuration, and
+  this info is required in imx-media-csi.c to setup the CSI.
+  Laurent Pinchart argues that instead the CSI subdev should call its
+  neighbor's g_mbus_config op (which should be propagated if necessary)
+  to get this info. However Hans Verkuil is planning to remove the
+  g_mbus_config op. For now this driver uses the parsed DT mbus config
+  method until this issue is resolved.
diff --git a/drivers/staging/media/imx/imx-media-dev.c b/drivers/staging/media/imx/imx-media-dev.c
new file mode 100644
index 0000000..5213210
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media-dev.c
@@ -0,0 +1,522 @@
+/*
+ * V4L2 Media Controller Driver for Freescale i.MX5/6 SOC
+ *
+ * Copyright (c) 2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/delay.h>
+#include <linux/fs.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/platform_device.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/timer.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-ioctl.h>
+#include <media/v4l2-mc.h>
+#include <video/imx-ipu-v3.h>
+#include <media/imx.h>
+#include "imx-media.h"
+
+static inline struct imx_media_dev *notifier2dev(struct v4l2_async_notifier *n)
+{
+	return container_of(n, struct imx_media_dev, subdev_notifier);
+}
+
+/*
+ * Find a subdev by device node or device name. This is called during
+ * driver load to form the async subdev list and bind them.
+ */
+struct imx_media_subdev *
+imx_media_find_async_subdev(struct imx_media_dev *imxmd,
+			    struct device_node *np,
+			    const char *devname)
+{
+	struct imx_media_subdev *imxsd;
+	int i;
+
+	for (i = 0; i < imxmd->subdev_notifier.num_subdevs; i++) {
+		imxsd = &imxmd->subdev[i];
+		switch (imxsd->asd.match_type) {
+		case V4L2_ASYNC_MATCH_OF:
+			if (np && imxsd->asd.match.of.node == np)
+				return imxsd;
+			break;
+		case V4L2_ASYNC_MATCH_DEVNAME:
+			if (devname &&
+			    !strcmp(imxsd->asd.match.device_name.name, devname))
+				return imxsd;
+			break;
+		default:
+			break;
+		}
+	}
+
+	return NULL;
+}
+
+/*
+ * Adds a subdev to the async subdev list. If np is non-NULL, adds
+ * the async as a V4L2_ASYNC_MATCH_OF match type, otherwise as a
+ * V4L2_ASYNC_MATCH_DEVNAME match type using the dev_name of the
+ * given platform_device. This is called during driver load when
+ * forming the async subdev list.
+ */
+struct imx_media_subdev *
+imx_media_add_async_subdev(struct imx_media_dev *imxmd,
+			   struct device_node *np,
+			   struct platform_device *pdev)
+{
+	struct imx_media_subdev *imxsd;
+	struct v4l2_async_subdev *asd;
+	const char *devname = NULL;
+	int sd_idx;
+
+	if (pdev)
+		devname = dev_name(&pdev->dev);
+
+	/* return NULL if this subdev already added */
+	if (imx_media_find_async_subdev(imxmd, np, devname)) {
+		dev_dbg(imxmd->md.dev, "%s: already added %s\n",
+			__func__, np ? np->name : devname);
+		return NULL;
+	}
+
+	sd_idx = imxmd->subdev_notifier.num_subdevs;
+	if (sd_idx >= IMX_MEDIA_MAX_SUBDEVS) {
+		dev_err(imxmd->md.dev, "%s: too many subdevs! can't add %s\n",
+			__func__, np ? np->name : devname);
+		return ERR_PTR(-ENOSPC);
+	}
+
+	imxsd = &imxmd->subdev[sd_idx];
+
+	asd = &imxsd->asd;
+	if (np) {
+		asd->match_type = V4L2_ASYNC_MATCH_OF;
+		asd->match.of.node = np;
+	} else {
+		asd->match_type = V4L2_ASYNC_MATCH_DEVNAME;
+		strncpy(imxsd->devname, devname, sizeof(imxsd->devname));
+		asd->match.device_name.name = imxsd->devname;
+		imxsd->pdev = pdev;
+	}
+
+	imxmd->async_ptrs[sd_idx] = asd;
+	imxmd->subdev_notifier.num_subdevs++;
+
+	dev_dbg(imxmd->md.dev, "%s: added %s, match type %s\n",
+		__func__, np ? np->name : devname, np ? "OF" : "DEVNAME");
+
+	return imxsd;
+}
+
+/*
+ * Adds an imx-media link to a subdev pad's link list. This is called
+ * during driver load when forming the links between subdevs.
+ *
+ * @pad: the local pad
+ * @remote_node: the device node of the remote subdev
+ * @remote_devname: the device name of the remote subdev
+ * @local_pad: local pad index
+ * @remote_pad: remote pad index
+ */
+int imx_media_add_pad_link(struct imx_media_dev *imxmd,
+			   struct imx_media_pad *pad,
+			   struct device_node *remote_node,
+			   const char *remote_devname,
+			   int local_pad, int remote_pad)
+{
+	struct imx_media_link *link;
+	int link_idx;
+
+	link_idx = pad->num_links;
+	if (link_idx >= IMX_MEDIA_MAX_LINKS) {
+		dev_err(imxmd->md.dev, "%s: too many links!\n", __func__);
+		return -ENOSPC;
+	}
+
+	link = &pad->link[link_idx];
+
+	link->remote_sd_node = remote_node;
+	if (remote_devname)
+		strncpy(link->remote_devname, remote_devname,
+			sizeof(link->remote_devname));
+
+	link->local_pad = local_pad;
+	link->remote_pad = remote_pad;
+
+	pad->num_links++;
+
+	return 0;
+}
+
+/*
+ * get IPU from this CSI and add it to the list of IPUs
+ * the media driver will control.
+ */
+static int imx_media_get_ipu(struct imx_media_dev *imxmd,
+			     struct v4l2_subdev *csi_sd)
+{
+	struct ipu_soc *ipu;
+	int ipu_id;
+
+	ipu = dev_get_drvdata(csi_sd->dev->parent);
+	if (!ipu) {
+		v4l2_err(&imxmd->v4l2_dev,
+			 "CSI %s has no parent IPU!\n", csi_sd->name);
+		return -ENODEV;
+	}
+
+	ipu_id = ipu_get_num(ipu);
+	if (ipu_id > 1) {
+		v4l2_err(&imxmd->v4l2_dev, "invalid IPU id %d!\n", ipu_id);
+		return -ENODEV;
+	}
+
+	if (!imxmd->ipu[ipu_id])
+		imxmd->ipu[ipu_id] = ipu;
+
+	return 0;
+}
+
+/* async subdev bound notifier */
+static int imx_media_subdev_bound(struct v4l2_async_notifier *notifier,
+				  struct v4l2_subdev *sd,
+				  struct v4l2_async_subdev *asd)
+{
+	struct imx_media_dev *imxmd = notifier2dev(notifier);
+	struct imx_media_subdev *imxsd;
+	int ret = -EINVAL;
+
+	imxsd = imx_media_find_async_subdev(imxmd, sd->of_node,
+					    dev_name(sd->dev));
+	if (!imxsd)
+		goto out;
+
+	if (sd->grp_id & IMX_MEDIA_GRP_ID_CSI) {
+		ret = imx_media_get_ipu(imxmd, sd);
+		if (ret)
+			return ret;
+	} else if (sd->entity.function == MEDIA_ENT_F_VID_MUX) {
+		/* this is a video mux */
+		sd->grp_id = IMX_MEDIA_GRP_ID_VIDMUX;
+	} else if (imxsd->num_sink_pads == 0) {
+		/*
+		 * this is an original source of video frames, it
+		 * could be a camera sensor, an analog decoder, or
+		 * a bridge device (HDMI -> MIPI CSI-2 for example).
+		 * This group ID is used to locate the entity that
+		 * is the original source of video in a pipeline.
+		 */
+		sd->grp_id = IMX_MEDIA_GRP_ID_SENSOR;
+	}
+
+	/* attach the subdev */
+	imxsd->sd = sd;
+
+	ret = 0;
+out:
+	if (ret)
+		v4l2_warn(&imxmd->v4l2_dev,
+			  "Received unknown subdev %s\n", sd->name);
+	else
+		v4l2_info(&imxmd->v4l2_dev,
+			  "Registered subdev %s\n", sd->name);
+
+	return ret;
+}
+
+/*
+ * create a single media link given a local subdev, a single pad from that
+ * subdev, and a single link from that pad. Called after all subdevs have
+ * registered.
+ */
+static int imx_media_create_link(struct imx_media_dev *imxmd,
+				 struct imx_media_subdev *local_sd,
+				 struct imx_media_pad *pad,
+				 struct imx_media_link *link)
+{
+	struct imx_media_subdev *remote_sd;
+	struct v4l2_subdev *source, *sink;
+	u16 source_pad, sink_pad;
+	int ret;
+
+	/* only create the source->sink links */
+	if (pad->pad.flags & MEDIA_PAD_FL_SINK)
+		return 0;
+
+	remote_sd = imx_media_find_async_subdev(imxmd, link->remote_sd_node,
+						link->remote_devname);
+	if (!remote_sd) {
+		v4l2_warn(&imxmd->v4l2_dev, "%s: no remote for %s:%d\n",
+			  __func__, local_sd->sd->name, link->local_pad);
+		return 0;
+	}
+
+	source = local_sd->sd;
+	sink = remote_sd->sd;
+	source_pad = link->local_pad;
+	sink_pad = link->remote_pad;
+
+	v4l2_info(&imxmd->v4l2_dev, "%s: %s:%d -> %s:%d\n", __func__,
+		  source->name, source_pad, sink->name, sink_pad);
+
+	ret = media_create_pad_link(&source->entity, source_pad,
+				    &sink->entity, sink_pad, 0);
+	if (ret)
+		v4l2_err(&imxmd->v4l2_dev,
+			 "create_pad_link failed: %d\n", ret);
+
+	return ret;
+}
+
+/*
+ * create the media links from all imx-media pads and their links.
+ * Called after all subdevs have registered.
+ */
+static int imx_media_create_links(struct imx_media_dev *imxmd)
+{
+	struct imx_media_subdev *local_sd;
+	struct imx_media_link *link;
+	struct imx_media_pad *pad;
+	int num_pads, i, j, k;
+	int ret = 0;
+
+	for (i = 0; i < imxmd->num_subdevs; i++) {
+		local_sd = &imxmd->subdev[i];
+		num_pads = local_sd->num_sink_pads + local_sd->num_src_pads;
+
+		for (j = 0; j < num_pads; j++) {
+			pad = &local_sd->pad[j];
+
+			for (k = 0; k < pad->num_links; k++) {
+				link = &pad->link[k];
+
+				ret = imx_media_create_link(imxmd, local_sd,
+							    pad, link);
+				if (ret)
+					goto out;
+			}
+		}
+	}
+
+out:
+	return ret;
+}
+
+/* async subdev complete notifier */
+static int imx_media_probe_complete(struct v4l2_async_notifier *notifier)
+{
+	struct imx_media_dev *imxmd = notifier2dev(notifier);
+	int i, ret;
+
+	mutex_lock(&imxmd->md.graph_mutex);
+
+	/* make sure all subdevs were bound */
+	for (i = 0; i < imxmd->num_subdevs; i++) {
+		if (!imxmd->subdev[i].sd) {
+			v4l2_err(&imxmd->v4l2_dev, "unbound subdev!\n");
+			ret = -ENODEV;
+			goto unlock;
+		}
+	}
+
+	ret = imx_media_create_links(imxmd);
+	if (ret)
+		goto unlock;
+
+	ret = v4l2_device_register_subdev_nodes(&imxmd->v4l2_dev);
+unlock:
+	mutex_unlock(&imxmd->md.graph_mutex);
+	if (ret)
+		return ret;
+
+	return media_device_register(&imxmd->md);
+}
+
+static int imx_media_link_notify(struct media_link *link, u32 flags,
+				 unsigned int notification)
+{
+	struct media_entity *source = link->source->entity;
+	struct media_entity *sink = link->sink->entity;
+	struct imx_media_dev *imxmd;
+	struct media_graph *graph;
+	struct video_device *vdev;
+	struct v4l2_subdev *sd;
+	int ret = 0;
+
+	if (is_media_entity_v4l2_subdev(sink))
+		sd = media_entity_to_v4l2_subdev(sink);
+	else
+		sd = media_entity_to_v4l2_subdev(source);
+
+	imxmd = dev_get_drvdata(sd->v4l2_dev->dev);
+	graph = &imxmd->link_notify_graph;
+
+	vdev = imx_media_find_pipeline_video_device(imxmd, sink);
+	if (!IS_ERR(vdev)) {
+		/*
+		 * reset video device controls on any change to
+		 * the pipeline.
+		 */
+		v4l2_ctrl_handler_free(vdev->ctrl_handler);
+		v4l2_ctrl_handler_init(vdev->ctrl_handler, 0);
+	} else {
+		vdev = NULL;
+	}
+
+	if (notification == MEDIA_DEV_NOTIFY_PRE_LINK_CH) {
+		ret = media_graph_walk_init(graph, &imxmd->md);
+		if (ret)
+			return ret;
+
+		if (flags & MEDIA_LNK_FL_ENABLED)
+			return 0;
+
+		/* Before link disconnection */
+		return imx_media_pipeline_set_power(imxmd, graph, sink, false);
+	}
+
+	/* MEDIA_DEV_NOTIFY_POST_LINK_CH */
+
+	if (!(link->flags & MEDIA_LNK_FL_ENABLED))
+		goto cleanup;
+
+	/* After link activation */
+	ret = imx_media_pipeline_set_power(imxmd, graph, sink, true);
+	if (ret)
+		goto cleanup;
+
+	if (vdev)
+		ret = __v4l2_pipeline_inherit_controls(vdev, sink);
+cleanup:
+	media_graph_walk_cleanup(graph);
+	return ret ? -EPIPE : 0;
+}
+
+static const struct media_device_ops imx_media_md_ops = {
+	.link_notify = imx_media_link_notify,
+};
+
+static int imx_media_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *node = dev->of_node;
+	struct imx_media_subdev *csi[4] = {0};
+	struct imx_media_dev *imxmd;
+	int ret;
+
+	imxmd = devm_kzalloc(dev, sizeof(*imxmd), GFP_KERNEL);
+	if (!imxmd)
+		return -ENOMEM;
+
+	dev_set_drvdata(dev, imxmd);
+
+	strlcpy(imxmd->md.model, "imx-media", sizeof(imxmd->md.model));
+	imxmd->md.ops = &imx_media_md_ops;
+	imxmd->md.dev = dev;
+
+	imxmd->v4l2_dev.mdev = &imxmd->md;
+	strlcpy(imxmd->v4l2_dev.name, "imx-media",
+		sizeof(imxmd->v4l2_dev.name));
+
+	media_device_init(&imxmd->md);
+
+	ret = v4l2_device_register(dev, &imxmd->v4l2_dev);
+	if (ret < 0) {
+		v4l2_err(&imxmd->v4l2_dev,
+			 "Failed to register v4l2_device: %d\n", ret);
+		goto cleanup;
+	}
+
+	dev_set_drvdata(imxmd->v4l2_dev.dev, imxmd);
+
+	ret = imx_media_of_parse(imxmd, &csi, node);
+	if (ret) {
+		v4l2_err(&imxmd->v4l2_dev,
+			 "imx_media_of_parse failed with %d\n", ret);
+		goto unreg_dev;
+	}
+
+	ret = imx_media_add_internal_subdevs(imxmd, csi);
+	if (ret) {
+		v4l2_err(&imxmd->v4l2_dev,
+			 "add_internal_subdevs failed with %d\n", ret);
+		goto unreg_dev;
+	}
+
+	/* no subdevs? just bail */
+	imxmd->num_subdevs = imxmd->subdev_notifier.num_subdevs;
+	if (imxmd->num_subdevs == 0) {
+		ret = -ENODEV;
+		goto unreg_dev;
+	}
+
+	/* prepare the async subdev notifier and register it */
+	imxmd->subdev_notifier.subdevs = imxmd->async_ptrs;
+	imxmd->subdev_notifier.bound = imx_media_subdev_bound;
+	imxmd->subdev_notifier.complete = imx_media_probe_complete;
+	ret = v4l2_async_notifier_register(&imxmd->v4l2_dev,
+					   &imxmd->subdev_notifier);
+	if (ret) {
+		v4l2_err(&imxmd->v4l2_dev,
+			 "v4l2_async_notifier_register failed with %d\n", ret);
+		goto del_int;
+	}
+
+	return 0;
+
+del_int:
+	imx_media_remove_internal_subdevs(imxmd);
+unreg_dev:
+	v4l2_device_unregister(&imxmd->v4l2_dev);
+cleanup:
+	media_device_cleanup(&imxmd->md);
+	return ret;
+}
+
+static int imx_media_remove(struct platform_device *pdev)
+{
+	struct imx_media_dev *imxmd =
+		(struct imx_media_dev *)platform_get_drvdata(pdev);
+
+	v4l2_info(&imxmd->v4l2_dev, "Removing imx-media\n");
+
+	v4l2_async_notifier_unregister(&imxmd->subdev_notifier);
+	imx_media_remove_internal_subdevs(imxmd);
+	v4l2_device_unregister(&imxmd->v4l2_dev);
+	media_device_unregister(&imxmd->md);
+	media_device_cleanup(&imxmd->md);
+
+	return 0;
+}
+
+static const struct of_device_id imx_media_dt_ids[] = {
+	{ .compatible = "fsl,imx-capture-subsystem" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, imx_media_dt_ids);
+
+static struct platform_driver imx_media_pdrv = {
+	.probe		= imx_media_probe,
+	.remove		= imx_media_remove,
+	.driver		= {
+		.name	= "imx-media",
+		.of_match_table	= imx_media_dt_ids,
+	},
+};
+
+module_platform_driver(imx_media_pdrv);
+
+MODULE_DESCRIPTION("i.MX5/6 v4l2 media controller driver");
+MODULE_AUTHOR("Steve Longerbeam <steve_longerbeam@mentor.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/staging/media/imx/imx-media-fim.c b/drivers/staging/media/imx/imx-media-fim.c
new file mode 100644
index 0000000..824d257
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media-fim.c
@@ -0,0 +1,471 @@
+/*
+ * Frame Interval Monitor.
+ *
+ * Copyright (c) 2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-of.h>
+#include <media/v4l2-subdev.h>
+#include <media/imx.h>
+#include "imx-media.h"
+
+enum {
+	FIM_CL_ENABLE = 0,
+	FIM_CL_NUM,
+	FIM_CL_TOLERANCE_MIN,
+	FIM_CL_TOLERANCE_MAX,
+	FIM_CL_NUM_SKIP,
+	FIM_NUM_CONTROLS,
+};
+
+#define FIM_CL_ENABLE_DEF          1 /* FIM enabled by default */
+#define FIM_CL_NUM_DEF             8 /* average 8 frames */
+#define FIM_CL_NUM_SKIP_DEF        2 /* skip 2 frames after restart */
+#define FIM_CL_TOLERANCE_MIN_DEF  50 /* usec */
+#define FIM_CL_TOLERANCE_MAX_DEF   0 /* no max tolerance (unbounded) */
+
+struct imx_media_fim {
+	struct imx_media_dev *md;
+
+	/* the owning subdev of this fim instance */
+	struct v4l2_subdev *sd;
+
+	/* FIM's control handler */
+	struct v4l2_ctrl_handler ctrl_handler;
+
+	/* control cluster */
+	struct v4l2_ctrl  *ctrl[FIM_NUM_CONTROLS];
+
+	/* current control values */
+	bool              enabled;
+	int               num_avg;
+	int               num_skip;
+	unsigned long     tolerance_min; /* usec */
+	unsigned long     tolerance_max; /* usec */
+
+	int               counter;
+	struct timespec   last_ts;
+	unsigned long     sum;       /* usec */
+	unsigned long     nominal;   /* usec */
+
+	/*
+	 * input capture method of measuring FI (channel and flags
+	 * from device tree)
+	 */
+	int               icap_channel;
+	int               icap_flags;
+	struct completion icap_first_event;
+};
+
+static void update_fim_nominal(struct imx_media_fim *fim,
+			       struct imx_media_subdev *sensor)
+{
+	struct v4l2_streamparm parm;
+	struct v4l2_fract tpf;
+	int ret;
+
+	parm.type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
+	ret = v4l2_subdev_call(sensor->sd, video, g_parm, &parm);
+	tpf = parm.parm.capture.timeperframe;
+
+	if (ret || tpf.denominator == 0) {
+		dev_dbg(fim->sd->dev, "no tpf from sensor, FIM disabled\n");
+		fim->enabled = false;
+		return;
+	}
+
+	fim->nominal = DIV_ROUND_CLOSEST(1000 * 1000 * tpf.numerator,
+					 tpf.denominator);
+
+	dev_dbg(fim->sd->dev, "sensor FI=%lu usec\n", fim->nominal);
+}
+
+static void reset_fim(struct imx_media_fim *fim, bool curval)
+{
+	struct v4l2_ctrl *en = fim->ctrl[FIM_CL_ENABLE];
+	struct v4l2_ctrl *num = fim->ctrl[FIM_CL_NUM];
+	struct v4l2_ctrl *skip = fim->ctrl[FIM_CL_NUM_SKIP];
+	struct v4l2_ctrl *tol_min = fim->ctrl[FIM_CL_TOLERANCE_MIN];
+	struct v4l2_ctrl *tol_max = fim->ctrl[FIM_CL_TOLERANCE_MAX];
+
+	if (curval) {
+		fim->enabled = en->cur.val;
+		fim->num_avg = num->cur.val;
+		fim->num_skip = skip->cur.val;
+		fim->tolerance_min = tol_min->cur.val;
+		fim->tolerance_max = tol_max->cur.val;
+	} else {
+		fim->enabled = en->val;
+		fim->num_avg = num->val;
+		fim->num_skip = skip->val;
+		fim->tolerance_min = tol_min->val;
+		fim->tolerance_max = tol_max->val;
+	}
+
+	/* disable tolerance range if max <= min */
+	if (fim->tolerance_max <= fim->tolerance_min)
+		fim->tolerance_max = 0;
+
+	fim->counter = -fim->num_skip;
+	fim->sum = 0;
+}
+
+static void send_fim_event(struct imx_media_fim *fim, unsigned long error)
+{
+	static const struct v4l2_event ev = {
+		.type = V4L2_EVENT_FRAME_INTERVAL_ERROR,
+	};
+
+	v4l2_subdev_notify_event(fim->sd, &ev);
+}
+
+/*
+ * Monitor an averaged frame interval. If the average deviates too much
+ * from the sensor's nominal frame rate, send the frame interval error
+ * event. The frame intervals are averaged in order to quiet noise from
+ * (presumably random) interrupt latency.
+ */
+static void frame_interval_monitor(struct imx_media_fim *fim,
+				   struct timespec *ts)
+{
+	unsigned long interval, error, error_avg;
+	struct timespec diff;
+	bool send_event = false;
+
+	if (!fim->enabled || ++fim->counter <= 0)
+		goto out_update_ts;
+
+	diff = timespec_sub(*ts, fim->last_ts);
+	interval = diff.tv_sec * 1000 * 1000 + diff.tv_nsec / 1000;
+	error = abs(interval - fim->nominal);
+
+	if (fim->tolerance_max && error >= fim->tolerance_max) {
+		dev_dbg(fim->sd->dev,
+			"FIM: %lu ignored, out of tolerance bounds\n",
+			error);
+		fim->counter--;
+		goto out_update_ts;
+	}
+
+	fim->sum += error;
+
+	if (fim->counter == fim->num_avg) {
+		error_avg = DIV_ROUND_CLOSEST(fim->sum, fim->num_avg);
+
+		if (error_avg > fim->tolerance_min)
+			send_event = true;
+
+		dev_dbg(fim->sd->dev, "FIM: error: %lu usec%s\n",
+			error_avg, send_event ? " (!!!)" : "");
+
+		fim->counter = 0;
+		fim->sum = 0;
+	}
+
+out_update_ts:
+	fim->last_ts = *ts;
+	if (send_event)
+		send_fim_event(fim, error_avg);
+}
+
+#ifdef CONFIG_IMX_GPT_ICAP
+/*
+ * Input Capture method of measuring frame intervals. Not subject
+ * to interrupt latency.
+ */
+static void fim_input_capture_handler(int channel, void *dev_id,
+				      struct timespec *ts)
+{
+	struct imx_media_fim *fim = dev_id;
+
+	frame_interval_monitor(fim, ts);
+
+	if (!completion_done(&fim->icap_first_event))
+		complete(&fim->icap_first_event);
+}
+
+static int fim_request_input_capture(struct imx_media_fim *fim)
+{
+	init_completion(&fim->icap_first_event);
+
+	return mxc_request_input_capture(fim->icap_channel,
+					 fim_input_capture_handler,
+					 fim->icap_flags, fim);
+}
+
+static void fim_free_input_capture(struct imx_media_fim *fim)
+{
+	mxc_free_input_capture(fim->icap_channel, fim);
+}
+
+#else /* CONFIG_IMX_GPT_ICAP */
+
+static int fim_request_input_capture(struct imx_media_fim *fim)
+{
+	return 0;
+}
+
+static void fim_free_input_capture(struct imx_media_fim *fim)
+{
+}
+
+#endif /* CONFIG_IMX_GPT_ICAP */
+
+/*
+ * In case we are monitoring the first frame interval after streamon
+ * (when fim->num_skip = 0), we need a valid fim->last_ts before we
+ * can begin. This only applies to the input capture method. It is not
+ * possible to accurately measure the first FI after streamon using the
+ * EOF method, so fim->num_skip minimum is set to 1 in that case, so this
+ * function is a noop when the EOF method is used.
+ */
+static void fim_acquire_first_ts(struct imx_media_fim *fim)
+{
+	unsigned long ret;
+
+	if (!fim->enabled || fim->num_skip > 0)
+		return;
+
+	ret = wait_for_completion_timeout(
+		&fim->icap_first_event,
+		msecs_to_jiffies(IMX_MEDIA_EOF_TIMEOUT));
+	if (ret == 0)
+		v4l2_warn(fim->sd, "wait first icap event timeout\n");
+}
+
+/* FIM Controls */
+static int fim_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct imx_media_fim *fim = container_of(ctrl->handler,
+						 struct imx_media_fim,
+						 ctrl_handler);
+
+	switch (ctrl->id) {
+	case V4L2_CID_IMX_FIM_ENABLE:
+		reset_fim(fim, false);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static const struct v4l2_ctrl_ops fim_ctrl_ops = {
+	.s_ctrl = fim_s_ctrl,
+};
+
+static const struct v4l2_ctrl_config imx_media_fim_ctrl[] = {
+	[FIM_CL_ENABLE] = {
+		.ops = &fim_ctrl_ops,
+		.id = V4L2_CID_IMX_FIM_ENABLE,
+		.name = "FIM Enable",
+		.type = V4L2_CTRL_TYPE_BOOLEAN,
+		.def = FIM_CL_ENABLE_DEF,
+		.min = 0,
+		.max = 1,
+		.step = 1,
+	},
+	[FIM_CL_NUM] = {
+		.ops = &fim_ctrl_ops,
+		.id = V4L2_CID_IMX_FIM_NUM,
+		.name = "FIM Num Average",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.def = FIM_CL_NUM_DEF,
+		.min =  1, /* no averaging */
+		.max = 64, /* average 64 frames */
+		.step = 1,
+	},
+	[FIM_CL_TOLERANCE_MIN] = {
+		.ops = &fim_ctrl_ops,
+		.id = V4L2_CID_IMX_FIM_TOLERANCE_MIN,
+		.name = "FIM Tolerance Min",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.def = FIM_CL_TOLERANCE_MIN_DEF,
+		.min =    2,
+		.max =  200,
+		.step =   1,
+	},
+	[FIM_CL_TOLERANCE_MAX] = {
+		.ops = &fim_ctrl_ops,
+		.id = V4L2_CID_IMX_FIM_TOLERANCE_MAX,
+		.name = "FIM Tolerance Max",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.def = FIM_CL_TOLERANCE_MAX_DEF,
+		.min =    0,
+		.max =  500,
+		.step =   1,
+	},
+	[FIM_CL_NUM_SKIP] = {
+		.ops = &fim_ctrl_ops,
+		.id = V4L2_CID_IMX_FIM_NUM_SKIP,
+		.name = "FIM Num Skip",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.def = FIM_CL_NUM_SKIP_DEF,
+		.min =   0, /* skip no frames */
+		.max = 256, /* skip 256 frames */
+		.step =  1,
+	},
+};
+
+static int init_fim_controls(struct imx_media_fim *fim)
+{
+	struct v4l2_ctrl_handler *hdlr = &fim->ctrl_handler;
+	struct v4l2_ctrl_config fim_c;
+	int i, ret;
+
+	v4l2_ctrl_handler_init(hdlr, FIM_NUM_CONTROLS);
+
+	for (i = 0; i < FIM_NUM_CONTROLS; i++) {
+		fim_c = imx_media_fim_ctrl[i];
+
+		/*
+		 * it's not possible to accurately measure the first
+		 * FI after streamon using the EOF method, so force
+		 * num_skip minimum to 1 in that case.
+		 */
+		if (i == FIM_CL_NUM_SKIP && fim->icap_channel < 0)
+			fim_c.min = 1;
+
+		fim->ctrl[i] = v4l2_ctrl_new_custom(hdlr, &fim_c, NULL);
+	}
+
+	if (hdlr->error) {
+		ret = hdlr->error;
+		goto err_free;
+	}
+
+	v4l2_ctrl_cluster(FIM_NUM_CONTROLS, fim->ctrl);
+
+	/* add the FIM controls to the calling subdev ctrl handler */
+	ret = v4l2_ctrl_add_handler(fim->sd->ctrl_handler,
+				    &fim->ctrl_handler, NULL);
+	if (ret)
+		goto err_free;
+
+	return 0;
+err_free:
+	v4l2_ctrl_handler_free(hdlr);
+	return ret;
+}
+
+static int of_parse_fim(struct imx_media_fim *fim, struct device_node *np)
+{
+	struct device_node *fim_np;
+	u32 icap[2];
+	int ret;
+
+	/* by default EOF method is used */
+	fim->icap_channel = -1;
+
+	fim_np = of_get_child_by_name(np, "fim");
+	if (!fim_np || !of_device_is_available(fim_np)) {
+		of_node_put(fim_np);
+		return -ENODEV;
+	}
+
+	if (IS_ENABLED(CONFIG_IMX_GPT_ICAP)) {
+		ret = of_property_read_u32_array(fim_np,
+						 "fsl,input-capture-channel",
+						 icap, 2);
+		if (!ret) {
+			fim->icap_channel = icap[0];
+			fim->icap_flags = icap[1];
+		}
+	}
+
+	of_node_put(fim_np);
+	return 0;
+}
+
+/*
+ * Monitor frame intervals via EOF interrupt. This method is
+ * subject to uncertainty errors introduced by interrupt latency.
+ *
+ * This is a noop if the Input Capture method is being used, since
+ * the frame_interval_monitor() is called by the input capture event
+ * callback handler in that case.
+ */
+void imx_media_fim_eof_monitor(struct imx_media_fim *fim, struct timespec *ts)
+{
+	if (fim->icap_channel >= 0)
+		return;
+
+	frame_interval_monitor(fim, ts);
+}
+EXPORT_SYMBOL_GPL(imx_media_fim_eof_monitor);
+
+/* Called by the subdev in its s_power callback */
+int imx_media_fim_set_power(struct imx_media_fim *fim, bool on)
+{
+	int ret = 0;
+
+	if (fim->icap_channel >= 0) {
+		if (on)
+			ret = fim_request_input_capture(fim);
+		else
+			fim_free_input_capture(fim);
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(imx_media_fim_set_power);
+
+/* Called by the subdev in its s_stream callback */
+int imx_media_fim_set_stream(struct imx_media_fim *fim,
+			     struct imx_media_subdev *sensor,
+			     bool on)
+{
+	if (on) {
+		reset_fim(fim, true);
+		update_fim_nominal(fim, sensor);
+
+		if (fim->icap_channel >= 0)
+			fim_acquire_first_ts(fim);
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_fim_set_stream);
+
+/* Called by the subdev in its subdev registered callback */
+struct imx_media_fim *imx_media_fim_init(struct v4l2_subdev *sd)
+{
+	struct device_node *node = sd->of_node;
+	struct imx_media_fim *fim;
+	int ret;
+
+	fim = devm_kzalloc(sd->dev, sizeof(*fim), GFP_KERNEL);
+	if (!fim)
+		return ERR_PTR(-ENOMEM);
+
+	/* get media device */
+	fim->md = dev_get_drvdata(sd->v4l2_dev->dev);
+	fim->sd = sd;
+
+	ret = of_parse_fim(fim, node);
+	if (ret)
+		return (ret == -ENODEV) ? NULL : ERR_PTR(ret);
+
+	ret = init_fim_controls(fim);
+	if (ret)
+		return ERR_PTR(ret);
+
+	return fim;
+}
+EXPORT_SYMBOL_GPL(imx_media_fim_init);
+
+void imx_media_fim_free(struct imx_media_fim *fim)
+{
+	v4l2_ctrl_handler_free(&fim->ctrl_handler);
+}
+EXPORT_SYMBOL_GPL(imx_media_fim_free);
diff --git a/drivers/staging/media/imx/imx-media-internal-sd.c b/drivers/staging/media/imx/imx-media-internal-sd.c
new file mode 100644
index 0000000..cdfbf40
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media-internal-sd.c
@@ -0,0 +1,349 @@
+/*
+ * Media driver for Freescale i.MX5/6 SOC
+ *
+ * Adds the internal subdevices and the media links between them.
+ *
+ * Copyright (c) 2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/platform_device.h>
+#include "imx-media.h"
+
+enum isd_enum {
+	isd_csi0 = 0,
+	isd_csi1,
+	isd_vdic,
+	isd_ic_prp,
+	isd_ic_prpenc,
+	isd_ic_prpvf,
+	num_isd,
+};
+
+static const struct internal_subdev_id {
+	enum isd_enum index;
+	const char *name;
+	u32 grp_id;
+} isd_id[num_isd] = {
+	[isd_csi0] = {
+		.index = isd_csi0,
+		.grp_id = IMX_MEDIA_GRP_ID_CSI0,
+		.name = "imx-ipuv3-csi",
+	},
+	[isd_csi1] = {
+		.index = isd_csi1,
+		.grp_id = IMX_MEDIA_GRP_ID_CSI1,
+		.name = "imx-ipuv3-csi",
+	},
+	[isd_vdic] = {
+		.index = isd_vdic,
+		.grp_id = IMX_MEDIA_GRP_ID_VDIC,
+		.name = "imx-ipuv3-vdic",
+	},
+	[isd_ic_prp] = {
+		.index = isd_ic_prp,
+		.grp_id = IMX_MEDIA_GRP_ID_IC_PRP,
+		.name = "imx-ipuv3-ic",
+	},
+	[isd_ic_prpenc] = {
+		.index = isd_ic_prpenc,
+		.grp_id = IMX_MEDIA_GRP_ID_IC_PRPENC,
+		.name = "imx-ipuv3-ic",
+	},
+	[isd_ic_prpvf] = {
+		.index = isd_ic_prpvf,
+		.grp_id = IMX_MEDIA_GRP_ID_IC_PRPVF,
+		.name = "imx-ipuv3-ic",
+	},
+};
+
+struct internal_link {
+	const struct internal_subdev_id *remote_id;
+	int remote_pad;
+};
+
+struct internal_pad {
+	bool devnode; /* does this pad link to a device node */
+	struct internal_link link[IMX_MEDIA_MAX_LINKS];
+};
+
+static const struct internal_subdev {
+	const struct internal_subdev_id *id;
+	struct internal_pad pad[IMX_MEDIA_MAX_PADS];
+	int num_sink_pads;
+	int num_src_pads;
+} internal_subdev[num_isd] = {
+	[isd_csi0] = {
+		.id = &isd_id[isd_csi0],
+		.num_sink_pads = CSI_NUM_SINK_PADS,
+		.num_src_pads = CSI_NUM_SRC_PADS,
+		.pad[CSI_SRC_PAD_DIRECT] = {
+			.link = {
+				{
+					.remote_id = &isd_id[isd_ic_prp],
+					.remote_pad = PRP_SINK_PAD,
+				}, {
+					.remote_id =  &isd_id[isd_vdic],
+					.remote_pad = VDIC_SINK_PAD_DIRECT,
+				},
+			},
+		},
+		.pad[CSI_SRC_PAD_IDMAC] = {
+			.devnode = true,
+		},
+	},
+
+	[isd_csi1] = {
+		.id = &isd_id[isd_csi1],
+		.num_sink_pads = CSI_NUM_SINK_PADS,
+		.num_src_pads = CSI_NUM_SRC_PADS,
+		.pad[CSI_SRC_PAD_DIRECT] = {
+			.link = {
+				{
+					.remote_id = &isd_id[isd_ic_prp],
+					.remote_pad = PRP_SINK_PAD,
+				}, {
+					.remote_id =  &isd_id[isd_vdic],
+					.remote_pad = VDIC_SINK_PAD_DIRECT,
+				},
+			},
+		},
+		.pad[CSI_SRC_PAD_IDMAC] = {
+			.devnode = true,
+		},
+	},
+
+	[isd_vdic] = {
+		.id = &isd_id[isd_vdic],
+		.num_sink_pads = VDIC_NUM_SINK_PADS,
+		.num_src_pads = VDIC_NUM_SRC_PADS,
+		.pad[VDIC_SINK_PAD_IDMAC] = {
+			.devnode = true,
+		},
+		.pad[VDIC_SRC_PAD_DIRECT] = {
+			.link = {
+				{
+					.remote_id =  &isd_id[isd_ic_prp],
+					.remote_pad = PRP_SINK_PAD,
+				},
+			},
+		},
+	},
+
+	[isd_ic_prp] = {
+		.id = &isd_id[isd_ic_prp],
+		.num_sink_pads = PRP_NUM_SINK_PADS,
+		.num_src_pads = PRP_NUM_SRC_PADS,
+		.pad[PRP_SRC_PAD_PRPENC] = {
+			.link = {
+				{
+					.remote_id = &isd_id[isd_ic_prpenc],
+					.remote_pad = 0,
+				},
+			},
+		},
+		.pad[PRP_SRC_PAD_PRPVF] = {
+			.link = {
+				{
+					.remote_id = &isd_id[isd_ic_prpvf],
+					.remote_pad = 0,
+				},
+			},
+		},
+	},
+
+	[isd_ic_prpenc] = {
+		.id = &isd_id[isd_ic_prpenc],
+		.num_sink_pads = PRPENCVF_NUM_SINK_PADS,
+		.num_src_pads = PRPENCVF_NUM_SRC_PADS,
+		.pad[PRPENCVF_SRC_PAD] = {
+			.devnode = true,
+		},
+	},
+
+	[isd_ic_prpvf] = {
+		.id = &isd_id[isd_ic_prpvf],
+		.num_sink_pads = PRPENCVF_NUM_SINK_PADS,
+		.num_src_pads = PRPENCVF_NUM_SRC_PADS,
+		.pad[PRPENCVF_SRC_PAD] = {
+			.devnode = true,
+		},
+	},
+};
+
+/* form a device name given a group id and ipu id */
+static inline void isd_id_to_devname(char *devname, int sz,
+				     const struct internal_subdev_id *id,
+				     int ipu_id)
+{
+	int pdev_id = ipu_id * num_isd + id->index;
+
+	snprintf(devname, sz, "%s.%d", id->name, pdev_id);
+}
+
+/* adds the links from given internal subdev */
+static int add_internal_links(struct imx_media_dev *imxmd,
+			      const struct internal_subdev *isd,
+			      struct imx_media_subdev *imxsd,
+			      int ipu_id)
+{
+	int i, num_pads, ret;
+
+	num_pads = isd->num_sink_pads + isd->num_src_pads;
+
+	for (i = 0; i < num_pads; i++) {
+		const struct internal_pad *intpad = &isd->pad[i];
+		struct imx_media_pad *pad = &imxsd->pad[i];
+		int j;
+
+		/* init the pad flags for this internal subdev */
+		pad->pad.flags = (i < isd->num_sink_pads) ?
+			MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
+		/* export devnode pad flag to the subdevs */
+		pad->devnode = intpad->devnode;
+
+		for (j = 0; ; j++) {
+			const struct internal_link *link;
+			char remote_devname[32];
+
+			link = &intpad->link[j];
+
+			if (!link->remote_id)
+				break;
+
+			isd_id_to_devname(remote_devname,
+					  sizeof(remote_devname),
+					  link->remote_id, ipu_id);
+
+			ret = imx_media_add_pad_link(imxmd, pad,
+						     NULL, remote_devname,
+						     i, link->remote_pad);
+			if (ret)
+				return ret;
+		}
+	}
+
+	return 0;
+}
+
+/* register an internal subdev as a platform device */
+static struct imx_media_subdev *
+add_internal_subdev(struct imx_media_dev *imxmd,
+		    const struct internal_subdev *isd,
+		    int ipu_id)
+{
+	struct imx_media_internal_sd_platformdata pdata;
+	struct platform_device_info pdevinfo = {0};
+	struct imx_media_subdev *imxsd;
+	struct platform_device *pdev;
+
+	pdata.grp_id = isd->id->grp_id;
+
+	/* the id of IPU this subdev will control */
+	pdata.ipu_id = ipu_id;
+
+	/* create subdev name */
+	imx_media_grp_id_to_sd_name(pdata.sd_name, sizeof(pdata.sd_name),
+				    pdata.grp_id, ipu_id);
+
+	pdevinfo.name = isd->id->name;
+	pdevinfo.id = ipu_id * num_isd + isd->id->index;
+	pdevinfo.parent = imxmd->md.dev;
+	pdevinfo.data = &pdata;
+	pdevinfo.size_data = sizeof(pdata);
+	pdevinfo.dma_mask = DMA_BIT_MASK(32);
+
+	pdev = platform_device_register_full(&pdevinfo);
+	if (IS_ERR(pdev))
+		return ERR_CAST(pdev);
+
+	imxsd = imx_media_add_async_subdev(imxmd, NULL, pdev);
+	if (IS_ERR(imxsd))
+		return imxsd;
+
+	imxsd->num_sink_pads = isd->num_sink_pads;
+	imxsd->num_src_pads = isd->num_src_pads;
+
+	return imxsd;
+}
+
+/* adds the internal subdevs in one ipu */
+static int add_ipu_internal_subdevs(struct imx_media_dev *imxmd,
+				    struct imx_media_subdev *csi0,
+				    struct imx_media_subdev *csi1,
+				    int ipu_id)
+{
+	enum isd_enum i;
+	int ret;
+
+	for (i = 0; i < num_isd; i++) {
+		const struct internal_subdev *isd = &internal_subdev[i];
+		struct imx_media_subdev *imxsd;
+
+		/*
+		 * the CSIs are represented in the device-tree, so those
+		 * devices are added already, and are added to the async
+		 * subdev list by of_parse_subdev(), so we are given those
+		 * subdevs as csi0 and csi1.
+		 */
+		switch (isd->id->grp_id) {
+		case IMX_MEDIA_GRP_ID_CSI0:
+			imxsd = csi0;
+			break;
+		case IMX_MEDIA_GRP_ID_CSI1:
+			imxsd = csi1;
+			break;
+		default:
+			imxsd = add_internal_subdev(imxmd, isd, ipu_id);
+			break;
+		}
+
+		if (IS_ERR(imxsd))
+			return PTR_ERR(imxsd);
+
+		/* add the links from this subdev */
+		if (imxsd) {
+			ret = add_internal_links(imxmd, isd, imxsd, ipu_id);
+			if (ret)
+				return ret;
+		}
+	}
+
+	return 0;
+}
+
+int imx_media_add_internal_subdevs(struct imx_media_dev *imxmd,
+				   struct imx_media_subdev *csi[4])
+{
+	int ret;
+
+	ret = add_ipu_internal_subdevs(imxmd, csi[0], csi[1], 0);
+	if (ret)
+		goto remove;
+
+	ret = add_ipu_internal_subdevs(imxmd, csi[2], csi[3], 1);
+	if (ret)
+		goto remove;
+
+	return 0;
+
+remove:
+	imx_media_remove_internal_subdevs(imxmd);
+	return ret;
+}
+
+void imx_media_remove_internal_subdevs(struct imx_media_dev *imxmd)
+{
+	struct imx_media_subdev *imxsd;
+	int i;
+
+	for (i = 0; i < imxmd->subdev_notifier.num_subdevs; i++) {
+		imxsd = &imxmd->subdev[i];
+		if (!imxsd->pdev)
+			continue;
+		platform_device_unregister(imxsd->pdev);
+	}
+}
diff --git a/drivers/staging/media/imx/imx-media-of.c b/drivers/staging/media/imx/imx-media-of.c
new file mode 100644
index 0000000..b383be4
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media-of.c
@@ -0,0 +1,267 @@
+/*
+ * Media driver for Freescale i.MX5/6 SOC
+ *
+ * Open Firmware parsing.
+ *
+ * Copyright (c) 2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/of_platform.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-of.h>
+#include <media/v4l2-subdev.h>
+#include <media/videobuf2-dma-contig.h>
+#include <video/imx-ipu-v3.h>
+#include "imx-media.h"
+
+static int of_add_pad_link(struct imx_media_dev *imxmd,
+			   struct imx_media_pad *pad,
+			   struct device_node *local_sd_node,
+			   struct device_node *remote_sd_node,
+			   int local_pad, int remote_pad)
+{
+	dev_dbg(imxmd->md.dev, "%s: adding %s:%d -> %s:%d\n", __func__,
+		local_sd_node->name, local_pad,
+		remote_sd_node->name, remote_pad);
+
+	return imx_media_add_pad_link(imxmd, pad, remote_sd_node, NULL,
+				      local_pad, remote_pad);
+}
+
+static void of_parse_sensor(struct imx_media_dev *imxmd,
+			    struct imx_media_subdev *sensor,
+			    struct device_node *sensor_np)
+{
+	struct device_node *endpoint;
+
+	endpoint = of_graph_get_next_endpoint(sensor_np, NULL);
+	if (endpoint) {
+		v4l2_of_parse_endpoint(endpoint, &sensor->sensor_ep);
+		of_node_put(endpoint);
+	}
+}
+
+static int of_get_port_count(const struct device_node *np)
+{
+	struct device_node *ports, *child;
+	int num = 0;
+
+	/* check if this node has a ports subnode */
+	ports = of_get_child_by_name(np, "ports");
+	if (ports)
+		np = ports;
+
+	for_each_child_of_node(np, child)
+		if (of_node_cmp(child->name, "port") == 0)
+			num++;
+
+	of_node_put(ports);
+	return num;
+}
+
+/*
+ * find the remote device node and remote port id (remote pad #)
+ * given local endpoint node
+ */
+static void of_get_remote_pad(struct device_node *epnode,
+			      struct device_node **remote_node,
+			      int *remote_pad)
+{
+	struct device_node *rp, *rpp;
+	struct device_node *remote;
+
+	rp = of_graph_get_remote_port(epnode);
+	rpp = of_graph_get_remote_port_parent(epnode);
+
+	if (of_device_is_compatible(rpp, "fsl,imx6q-ipu")) {
+		/* the remote is one of the CSI ports */
+		remote = rp;
+		*remote_pad = 0;
+		of_node_put(rpp);
+	} else {
+		remote = rpp;
+		of_property_read_u32(rp, "reg", remote_pad);
+		of_node_put(rp);
+	}
+
+	if (!remote || !of_device_is_available(remote)) {
+		of_node_put(remote);
+		*remote_node = NULL;
+	} else {
+		*remote_node = remote;
+	}
+}
+
+static struct imx_media_subdev *
+of_parse_subdev(struct imx_media_dev *imxmd, struct device_node *sd_np,
+		bool is_csi_port)
+{
+	struct imx_media_subdev *imxsd;
+	int i, num_pads, ret;
+
+	if (!of_device_is_available(sd_np)) {
+		dev_dbg(imxmd->md.dev, "%s: %s not enabled\n", __func__,
+			sd_np->name);
+		return NULL;
+	}
+
+	/* register this subdev with async notifier */
+	imxsd = imx_media_add_async_subdev(imxmd, sd_np, NULL);
+	if (IS_ERR_OR_NULL(imxsd))
+		return imxsd;
+
+	if (is_csi_port) {
+		/*
+		 * the ipu-csi has one sink port and two source ports.
+		 * The source ports are not represented in the device tree,
+		 * but are described by the internal pads and links later.
+		 */
+		num_pads = CSI_NUM_PADS;
+		imxsd->num_sink_pads = CSI_NUM_SINK_PADS;
+	} else if (of_device_is_compatible(sd_np, "fsl,imx6-mipi-csi2")) {
+		num_pads = of_get_port_count(sd_np);
+		/* the mipi csi2 receiver has only one sink port */
+		imxsd->num_sink_pads = 1;
+	} else if (of_device_is_compatible(sd_np, "video-multiplexer")) {
+		num_pads = of_get_port_count(sd_np);
+		/* for the video mux, all but the last port are sinks */
+		imxsd->num_sink_pads = num_pads - 1;
+	} else {
+		num_pads = of_get_port_count(sd_np);
+		if (num_pads != 1) {
+			dev_warn(imxmd->md.dev,
+				 "%s: unknown device %s with %d ports\n",
+				 __func__, sd_np->name, num_pads);
+			return NULL;
+		}
+
+		/*
+		 * we got to this node from this single source port,
+		 * there are no sink pads.
+		 */
+		imxsd->num_sink_pads = 0;
+	}
+
+	if (imxsd->num_sink_pads >= num_pads)
+		return ERR_PTR(-EINVAL);
+
+	imxsd->num_src_pads = num_pads - imxsd->num_sink_pads;
+
+	dev_dbg(imxmd->md.dev, "%s: %s has %d pads (%d sink, %d src)\n",
+		__func__, sd_np->name, num_pads,
+		imxsd->num_sink_pads, imxsd->num_src_pads);
+
+	/*
+	 * With no sink, this subdev node is the original source
+	 * of video, parse it's media bus fur use by the pipeline.
+	 */
+	if (imxsd->num_sink_pads == 0)
+		of_parse_sensor(imxmd, imxsd, sd_np);
+
+	for (i = 0; i < num_pads; i++) {
+		struct device_node *epnode = NULL, *port, *remote_np;
+		struct imx_media_subdev *remote_imxsd;
+		struct imx_media_pad *pad;
+		int remote_pad;
+
+		/* init this pad */
+		pad = &imxsd->pad[i];
+		pad->pad.flags = (i < imxsd->num_sink_pads) ?
+			MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
+
+		if (is_csi_port)
+			port = (i < imxsd->num_sink_pads) ? sd_np : NULL;
+		else
+			port = of_graph_get_port_by_id(sd_np, i);
+		if (!port)
+			continue;
+
+		for_each_child_of_node(port, epnode) {
+			of_get_remote_pad(epnode, &remote_np, &remote_pad);
+			if (!remote_np)
+				continue;
+
+			ret = of_add_pad_link(imxmd, pad, sd_np, remote_np,
+					      i, remote_pad);
+			if (ret) {
+				imxsd = ERR_PTR(ret);
+				break;
+			}
+
+			if (i < imxsd->num_sink_pads) {
+				/* follow sink endpoints upstream */
+				remote_imxsd = of_parse_subdev(imxmd,
+							       remote_np,
+							       false);
+				if (IS_ERR(remote_imxsd)) {
+					imxsd = remote_imxsd;
+					break;
+				}
+			}
+
+			of_node_put(remote_np);
+		}
+
+		if (port != sd_np)
+			of_node_put(port);
+		if (IS_ERR(imxsd)) {
+			of_node_put(remote_np);
+			of_node_put(epnode);
+			break;
+		}
+	}
+
+	return imxsd;
+}
+
+int imx_media_of_parse(struct imx_media_dev *imxmd,
+		       struct imx_media_subdev *(*csi)[4],
+		       struct device_node *np)
+{
+	struct imx_media_subdev *lcsi;
+	struct device_node *csi_np;
+	u32 ipu_id, csi_id;
+	int i, ret;
+
+	for (i = 0; ; i++) {
+		csi_np = of_parse_phandle(np, "ports", i);
+		if (!csi_np)
+			break;
+
+		lcsi = of_parse_subdev(imxmd, csi_np, true);
+		if (IS_ERR(lcsi)) {
+			ret = PTR_ERR(lcsi);
+			goto err_put;
+		}
+
+		ret = of_property_read_u32(csi_np, "reg", &csi_id);
+		if (ret) {
+			dev_err(imxmd->md.dev,
+				"%s: csi port missing reg property!\n",
+				__func__);
+			goto err_put;
+		}
+
+		ipu_id = of_alias_get_id(csi_np->parent, "ipu");
+		of_node_put(csi_np);
+
+		if (ipu_id > 1 || csi_id > 1) {
+			dev_err(imxmd->md.dev,
+				"%s: invalid ipu/csi id (%u/%u)\n",
+				__func__, ipu_id, csi_id);
+			return -EINVAL;
+		}
+
+		(*csi)[ipu_id * 2 + csi_id] = lcsi;
+	}
+
+	return 0;
+err_put:
+	of_node_put(csi_np);
+	return ret;
+}
diff --git a/drivers/staging/media/imx/imx-media-utils.c b/drivers/staging/media/imx/imx-media-utils.c
new file mode 100644
index 0000000..ee50b6a
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media-utils.c
@@ -0,0 +1,766 @@
+/*
+ * V4L2 Media Controller Driver for Freescale i.MX5/6 SOC
+ *
+ * Copyright (c) 2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/module.h>
+#include "imx-media.h"
+
+/*
+ * List of pixel formats for the subdevs. This must be a super-set of
+ * the formats supported by the ipu image converter.
+ *
+ * The non-mbus formats (planar and BGR) must all fall at the end of
+ * this table, otherwise enum_fmt() at media pads will stop before
+ * seeing all the supported mbus formats.
+ */
+static const struct imx_media_pixfmt imx_media_formats[] = {
+	{
+		.fourcc	= V4L2_PIX_FMT_UYVY,
+		.codes  = {
+			MEDIA_BUS_FMT_UYVY8_2X8,
+			MEDIA_BUS_FMT_UYVY8_1X16
+		},
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 16,
+	}, {
+		.fourcc	= V4L2_PIX_FMT_YUYV,
+		.codes  = {
+			MEDIA_BUS_FMT_YUYV8_2X8,
+			MEDIA_BUS_FMT_YUYV8_1X16
+		},
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 16,
+	}, {
+		.fourcc = V4L2_PIX_FMT_YUV32,
+		.codes  = {MEDIA_BUS_FMT_AYUV8_1X32},
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 32,
+		.ipufmt = true,
+	}, {
+		.fourcc	= V4L2_PIX_FMT_RGB565,
+		.codes  = {MEDIA_BUS_FMT_RGB565_2X8_LE},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 16,
+	}, {
+		.fourcc	= V4L2_PIX_FMT_RGB24,
+		.codes  = {
+			MEDIA_BUS_FMT_RGB888_1X24,
+			MEDIA_BUS_FMT_RGB888_2X12_LE
+		},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 24,
+	}, {
+		.fourcc	= V4L2_PIX_FMT_RGB32,
+		.codes  = {MEDIA_BUS_FMT_ARGB8888_1X32},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 32,
+		.ipufmt = true,
+	},
+	/*** non-mbus formats start here ***/
+	{
+		.fourcc	= V4L2_PIX_FMT_BGR24,
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 24,
+	}, {
+		.fourcc	= V4L2_PIX_FMT_BGR32,
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 32,
+	}, {
+		.fourcc	= V4L2_PIX_FMT_YUV420,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 12,
+		.planar = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_YVU420,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 12,
+		.planar = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_YUV422P,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 16,
+		.planar = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_NV12,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 12,
+		.planar = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_NV16,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 16,
+		.planar = true,
+	},
+};
+
+static const u32 imx_media_ipu_internal_codes[] = {
+	MEDIA_BUS_FMT_AYUV8_1X32, MEDIA_BUS_FMT_ARGB8888_1X32,
+};
+
+static inline u32 pixfmt_to_colorspace(const struct imx_media_pixfmt *fmt)
+{
+	return (fmt->cs == IPUV3_COLORSPACE_RGB) ?
+		V4L2_COLORSPACE_SRGB : V4L2_COLORSPACE_SMPTE170M;
+}
+
+static const struct imx_media_pixfmt *find_format(u32 fourcc, u32 code,
+						  bool allow_rgb,
+						  bool allow_planar,
+						  bool ipu_fmt_only)
+{
+	const struct imx_media_pixfmt *fmt, *ret = NULL;
+	int i, j;
+
+	for (i = 0; i < ARRAY_SIZE(imx_media_formats); i++) {
+		fmt = &imx_media_formats[i];
+
+		if (ipu_fmt_only && !fmt->ipufmt)
+			continue;
+
+		if (fourcc && fmt->fourcc == fourcc &&
+		    (fmt->cs != IPUV3_COLORSPACE_RGB || allow_rgb) &&
+		    (!fmt->planar || allow_planar)) {
+			ret = fmt;
+			goto out;
+		}
+
+		for (j = 0; code && fmt->codes[j]; j++) {
+			if (fmt->codes[j] == code && !fmt->planar &&
+			    (fmt->cs != IPUV3_COLORSPACE_RGB || allow_rgb)) {
+				ret = fmt;
+				goto out;
+			}
+		}
+	}
+out:
+	return ret;
+}
+
+const struct imx_media_pixfmt *imx_media_find_format(u32 fourcc, u32 code,
+						     bool allow_rgb,
+						     bool allow_planar)
+{
+	return find_format(fourcc, code, allow_rgb, allow_planar, false);
+}
+EXPORT_SYMBOL_GPL(imx_media_find_format);
+
+const struct imx_media_pixfmt *imx_media_find_ipu_format(u32 fourcc,
+							 u32 code,
+							 bool allow_rgb)
+{
+	return find_format(fourcc, code, allow_rgb, false, true);
+}
+EXPORT_SYMBOL_GPL(imx_media_find_ipu_format);
+
+int imx_media_enum_format(u32 *fourcc, u32 *code, u32 index,
+			  bool allow_rgb, bool allow_planar)
+{
+	const struct imx_media_pixfmt *fmt;
+
+	if (index >= ARRAY_SIZE(imx_media_formats))
+		return -EINVAL;
+
+	fmt = &imx_media_formats[index];
+
+	if ((fmt->cs == IPUV3_COLORSPACE_RGB && !allow_rgb) ||
+	    (fmt->planar && !allow_planar))
+		return -EINVAL;
+
+	if (code)
+		*code = fmt->codes[0];
+	if (fourcc)
+		*fourcc = fmt->fourcc;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_enum_format);
+
+int imx_media_enum_ipu_format(u32 *fourcc, u32 *code, u32 index,
+			      bool allow_rgb)
+{
+	const struct imx_media_pixfmt *fmt;
+	u32 lcode;
+
+	if (index >= ARRAY_SIZE(imx_media_ipu_internal_codes))
+		return -EINVAL;
+
+	lcode = imx_media_ipu_internal_codes[index];
+
+	fmt = find_format(0, lcode, allow_rgb, false, true);
+	if (!fmt)
+		return -EINVAL;
+
+	if (code)
+		*code = fmt->codes[0];
+	if (fourcc)
+		*fourcc = fmt->fourcc;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_enum_ipu_format);
+
+int imx_media_init_mbus_fmt(struct v4l2_mbus_framefmt *mbus,
+			    u32 width, u32 height, u32 code, u32 field,
+			    const struct imx_media_pixfmt **cc)
+{
+	const struct imx_media_pixfmt *lcc;
+
+	mbus->width = width;
+	mbus->height = height;
+	mbus->field = field;
+	if (code == 0)
+		imx_media_enum_format(NULL, &code, 0, true, false);
+	lcc = imx_media_find_format(0, code, true, false);
+	if (!lcc)
+		return -EINVAL;
+	mbus->code = code;
+	mbus->colorspace = pixfmt_to_colorspace(lcc);
+
+	if (cc)
+		*cc = lcc;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_init_mbus_fmt);
+
+int imx_media_mbus_fmt_to_pix_fmt(struct v4l2_pix_format *pix,
+				  struct v4l2_mbus_framefmt *mbus,
+				  const struct imx_media_pixfmt *cc)
+{
+	u32 stride;
+
+	if (!cc) {
+		cc = imx_media_find_format(0, mbus->code, true, false);
+		if (!cc)
+			return -EINVAL;
+	}
+
+	stride = cc->planar ? mbus->width : (mbus->width * cc->bpp) >> 3;
+
+	pix->width = mbus->width;
+	pix->height = mbus->height;
+	pix->pixelformat = cc->fourcc;
+	pix->colorspace = mbus->colorspace;
+	pix->xfer_func = mbus->xfer_func;
+	pix->ycbcr_enc = mbus->ycbcr_enc;
+	pix->quantization = mbus->quantization;
+	pix->field = mbus->field;
+	pix->bytesperline = stride;
+	pix->sizeimage = (pix->width * pix->height * cc->bpp) >> 3;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_mbus_fmt_to_pix_fmt);
+
+int imx_media_mbus_fmt_to_ipu_image(struct ipu_image *image,
+				    struct v4l2_mbus_framefmt *mbus)
+{
+	int ret;
+
+	memset(image, 0, sizeof(*image));
+
+	ret = imx_media_mbus_fmt_to_pix_fmt(&image->pix, mbus, NULL);
+	if (ret)
+		return ret;
+
+	image->rect.width = mbus->width;
+	image->rect.height = mbus->height;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_mbus_fmt_to_ipu_image);
+
+int imx_media_ipu_image_to_mbus_fmt(struct v4l2_mbus_framefmt *mbus,
+				    struct ipu_image *image)
+{
+	const struct imx_media_pixfmt *fmt;
+
+	fmt = imx_media_find_format(image->pix.pixelformat, 0, true, false);
+	if (!fmt)
+		return -EINVAL;
+
+	memset(mbus, 0, sizeof(*mbus));
+	mbus->width = image->pix.width;
+	mbus->height = image->pix.height;
+	mbus->code = fmt->codes[0];
+	mbus->colorspace = pixfmt_to_colorspace(fmt);
+	mbus->field = image->pix.field;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_ipu_image_to_mbus_fmt);
+
+void imx_media_free_dma_buf(struct imx_media_dev *imxmd,
+			    struct imx_media_dma_buf *buf)
+{
+	if (buf->virt)
+		dma_free_coherent(imxmd->md.dev, buf->len,
+				  buf->virt, buf->phys);
+
+	buf->virt = NULL;
+	buf->phys = 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_free_dma_buf);
+
+int imx_media_alloc_dma_buf(struct imx_media_dev *imxmd,
+			    struct imx_media_dma_buf *buf,
+			    int size)
+{
+	imx_media_free_dma_buf(imxmd, buf);
+
+	buf->len = PAGE_ALIGN(size);
+	buf->virt = dma_alloc_coherent(imxmd->md.dev, buf->len, &buf->phys,
+				       GFP_DMA | GFP_KERNEL);
+	if (!buf->virt) {
+		dev_err(imxmd->md.dev, "failed to alloc dma buffer\n");
+		return -ENOMEM;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_alloc_dma_buf);
+
+/* form a subdev name given a group id and ipu id */
+void imx_media_grp_id_to_sd_name(char *sd_name, int sz, u32 grp_id, int ipu_id)
+{
+	int id;
+
+	switch (grp_id) {
+	case IMX_MEDIA_GRP_ID_CSI0...IMX_MEDIA_GRP_ID_CSI1:
+		id = (grp_id >> IMX_MEDIA_GRP_ID_CSI_BIT) - 1;
+		snprintf(sd_name, sz, "ipu%d_csi%d", ipu_id + 1, id);
+		break;
+	case IMX_MEDIA_GRP_ID_VDIC:
+		snprintf(sd_name, sz, "ipu%d_vdic", ipu_id + 1);
+		break;
+	case IMX_MEDIA_GRP_ID_IC_PRP:
+		snprintf(sd_name, sz, "ipu%d_ic_prp", ipu_id + 1);
+		break;
+	case IMX_MEDIA_GRP_ID_IC_PRPENC:
+		snprintf(sd_name, sz, "ipu%d_ic_prpenc", ipu_id + 1);
+		break;
+	case IMX_MEDIA_GRP_ID_IC_PRPVF:
+		snprintf(sd_name, sz, "ipu%d_ic_prpvf", ipu_id + 1);
+		break;
+	default:
+		break;
+	}
+}
+EXPORT_SYMBOL_GPL(imx_media_grp_id_to_sd_name);
+
+struct imx_media_subdev *
+imx_media_find_subdev_by_sd(struct imx_media_dev *imxmd,
+			    struct v4l2_subdev *sd)
+{
+	struct imx_media_subdev *imxsd;
+	int i;
+
+	for (i = 0; i < imxmd->num_subdevs; i++) {
+		imxsd = &imxmd->subdev[i];
+		if (sd == imxsd->sd)
+			return imxsd;
+	}
+
+	return ERR_PTR(-ENODEV);
+}
+EXPORT_SYMBOL_GPL(imx_media_find_subdev_by_sd);
+
+struct imx_media_subdev *
+imx_media_find_subdev_by_id(struct imx_media_dev *imxmd, u32 grp_id)
+{
+	struct imx_media_subdev *imxsd;
+	int i;
+
+	for (i = 0; i < imxmd->num_subdevs; i++) {
+		imxsd = &imxmd->subdev[i];
+		if (imxsd->sd && imxsd->sd->grp_id == grp_id)
+			return imxsd;
+	}
+
+	return ERR_PTR(-ENODEV);
+}
+EXPORT_SYMBOL_GPL(imx_media_find_subdev_by_id);
+
+/*
+ * Search for an entity in the current pipeline, either a subdev
+ * with given grp_id, or a video device if vdev is true.
+ * Called with mdev->graph_mutex held.
+ */
+static struct media_entity *
+find_pipeline_entity(struct imx_media_dev *imxmd,
+		     struct media_graph *graph,
+		     struct media_entity *start_entity,
+		     u32 grp_id, bool vdev)
+{
+	struct media_entity *entity;
+	struct v4l2_subdev *sd;
+
+	media_graph_walk_start(graph, start_entity);
+
+	while ((entity = media_graph_walk_next(graph))) {
+		if ((vdev && !is_media_entity_v4l2_video_device(entity)) ||
+		    (!vdev && !is_media_entity_v4l2_subdev(entity)))
+			continue;
+
+		if (vdev)
+			return entity;
+
+		sd = media_entity_to_v4l2_subdev(entity);
+		if (sd->grp_id & grp_id)
+			return entity;
+	}
+
+	return NULL;
+}
+
+/*
+ * Search for a subdev in the current pipeline with given grp_id.
+ * Called with mdev->graph_mutex held.
+ */
+static struct v4l2_subdev *
+find_pipeline_subdev(struct imx_media_dev *imxmd,
+		     struct media_graph *graph,
+		     struct media_entity *start_entity,
+		     u32 grp_id)
+{
+	struct media_entity *entity = find_pipeline_entity(imxmd, graph,
+							   start_entity,
+							   grp_id, false);
+	return entity ? media_entity_to_v4l2_subdev(entity) : NULL;
+}
+
+/*
+ * Search for a video device in the current pipeline.
+ * Called with mdev->graph_mutex held.
+ */
+static struct video_device *
+find_pipeline_vdev(struct imx_media_dev *imxmd,
+		   struct media_graph *graph,
+		   struct media_entity *start_entity)
+{
+	struct media_entity *entity = find_pipeline_entity(imxmd, graph,
+							   start_entity,
+							   0, true);
+	return entity ? media_entity_to_video_device(entity) : NULL;
+}
+
+/*
+ * Search for an entity in the current pipeline with given grp_id,
+ * then locate the remote enabled source pad from that entity.
+ * Called with mdev->graph_mutex held.
+ */
+static struct media_pad *
+find_pipeline_remote_source_pad(struct imx_media_dev *imxmd,
+				struct media_graph *graph,
+				struct media_entity *start_entity,
+				u32 grp_id)
+{
+	struct media_pad *pad = NULL;
+	struct media_entity *me;
+	struct v4l2_subdev *sd;
+	int i;
+
+	sd = find_pipeline_subdev(imxmd, graph, start_entity, grp_id);
+	if (!sd)
+		return NULL;
+	me = &sd->entity;
+
+	/* Find remote source pad */
+	for (i = 0; i < me->num_pads; i++) {
+		struct media_pad *spad = &me->pads[i];
+
+		if (!(spad->flags & MEDIA_PAD_FL_SINK))
+			continue;
+		pad = media_entity_remote_pad(spad);
+		if (pad)
+			return pad;
+	}
+
+	return NULL;
+}
+
+/*
+ * Find the mipi-csi2 virtual channel reached from the given
+ * start entity in the current pipeline.
+ * Must be called with mdev->graph_mutex held.
+ */
+int imx_media_find_mipi_csi2_channel(struct imx_media_dev *imxmd,
+				     struct media_entity *start_entity)
+{
+	struct media_graph graph;
+	struct v4l2_subdev *sd;
+	struct media_pad *pad;
+	int ret;
+
+	ret = media_graph_walk_init(&graph, &imxmd->md);
+	if (ret)
+		return ret;
+
+	/* first try to locate the mipi-csi2 from the video mux */
+	pad = find_pipeline_remote_source_pad(imxmd, &graph, start_entity,
+					      IMX_MEDIA_GRP_ID_VIDMUX);
+	/* if couldn't reach it from there, try from a CSI */
+	if (!pad)
+		pad = find_pipeline_remote_source_pad(imxmd, &graph,
+						      start_entity,
+						      IMX_MEDIA_GRP_ID_CSI);
+	if (pad) {
+		sd = media_entity_to_v4l2_subdev(pad->entity);
+		if (sd->grp_id & IMX_MEDIA_GRP_ID_CSI2) {
+			ret = pad->index - 1; /* found it! */
+			dev_dbg(imxmd->md.dev, "found vc%d from %s\n",
+				ret, start_entity->name);
+			goto cleanup;
+		}
+	}
+
+	ret = -EPIPE;
+
+cleanup:
+	media_graph_walk_cleanup(&graph);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(imx_media_find_mipi_csi2_channel);
+
+/*
+ * Find a subdev reached from the given start entity in the
+ * current pipeline.
+ * Must be called with mdev->graph_mutex held.
+ */
+struct imx_media_subdev *
+imx_media_find_pipeline_subdev(struct imx_media_dev *imxmd,
+			       struct media_entity *start_entity,
+			       u32 grp_id)
+{
+	struct imx_media_subdev *imxsd;
+	struct media_graph graph;
+	struct v4l2_subdev *sd;
+	int ret;
+
+	ret = media_graph_walk_init(&graph, &imxmd->md);
+	if (ret)
+		return ERR_PTR(ret);
+
+	sd = find_pipeline_subdev(imxmd, &graph, start_entity, grp_id);
+	if (!sd) {
+		imxsd = ERR_PTR(-ENODEV);
+		goto cleanup;
+	}
+
+	imxsd = imx_media_find_subdev_by_sd(imxmd, sd);
+cleanup:
+	media_graph_walk_cleanup(&graph);
+	return imxsd;
+}
+EXPORT_SYMBOL_GPL(imx_media_find_pipeline_subdev);
+
+/*
+ * Find a video device reached from the given start entity in the
+ * current pipeline.
+ * Must be called with mdev->graph_mutex held.
+ */
+struct video_device *
+imx_media_find_pipeline_video_device(struct imx_media_dev *imxmd,
+				     struct media_entity *start_entity)
+{
+	struct video_device *vdev;
+	struct media_graph graph;
+	int ret;
+
+	ret = media_graph_walk_init(&graph, &imxmd->md);
+	if (ret)
+		return ERR_PTR(ret);
+
+	vdev = find_pipeline_vdev(imxmd, &graph, start_entity);
+	if (!vdev)
+		vdev = ERR_PTR(-ENODEV);
+
+	media_graph_walk_cleanup(&graph);
+	return vdev;
+}
+EXPORT_SYMBOL_GPL(imx_media_find_pipeline_video_device);
+
+struct imx_media_subdev *
+__imx_media_find_sensor(struct imx_media_dev *imxmd,
+			struct media_entity *start_entity)
+{
+	return imx_media_find_pipeline_subdev(imxmd, start_entity,
+					      IMX_MEDIA_GRP_ID_SENSOR);
+}
+EXPORT_SYMBOL_GPL(__imx_media_find_sensor);
+
+struct imx_media_subdev *
+imx_media_find_sensor(struct imx_media_dev *imxmd,
+		      struct media_entity *start_entity)
+{
+	struct imx_media_subdev *sensor;
+
+	mutex_lock(&imxmd->md.graph_mutex);
+	sensor = __imx_media_find_sensor(imxmd, start_entity);
+	mutex_unlock(&imxmd->md.graph_mutex);
+
+	return sensor;
+}
+EXPORT_SYMBOL_GPL(imx_media_find_sensor);
+
+/*
+ * The subdevs have to be powered on/off, and streaming
+ * enabled/disabled, in a specific sequence.
+ */
+static const u32 stream_on_seq[] = {
+	IMX_MEDIA_GRP_ID_IC_PRPVF,
+	IMX_MEDIA_GRP_ID_IC_PRPENC,
+	IMX_MEDIA_GRP_ID_IC_PRP,
+	IMX_MEDIA_GRP_ID_VDIC,
+	IMX_MEDIA_GRP_ID_CSI2,
+	IMX_MEDIA_GRP_ID_SENSOR,
+	IMX_MEDIA_GRP_ID_VIDMUX,
+	IMX_MEDIA_GRP_ID_CSI,
+};
+
+static const u32 stream_off_seq[] = {
+	IMX_MEDIA_GRP_ID_IC_PRPVF,
+	IMX_MEDIA_GRP_ID_IC_PRPENC,
+	IMX_MEDIA_GRP_ID_IC_PRP,
+	IMX_MEDIA_GRP_ID_VDIC,
+	IMX_MEDIA_GRP_ID_CSI,
+	IMX_MEDIA_GRP_ID_VIDMUX,
+	IMX_MEDIA_GRP_ID_SENSOR,
+	IMX_MEDIA_GRP_ID_CSI2,
+};
+
+#define NUM_STREAM_ENTITIES ARRAY_SIZE(stream_on_seq)
+
+static const u32 power_on_seq[] = {
+	IMX_MEDIA_GRP_ID_CSI2,
+	IMX_MEDIA_GRP_ID_SENSOR,
+	IMX_MEDIA_GRP_ID_VIDMUX,
+	IMX_MEDIA_GRP_ID_CSI,
+	IMX_MEDIA_GRP_ID_VDIC,
+	IMX_MEDIA_GRP_ID_IC_PRPENC,
+	IMX_MEDIA_GRP_ID_IC_PRPVF,
+};
+
+static const u32 power_off_seq[] = {
+	IMX_MEDIA_GRP_ID_IC_PRPVF,
+	IMX_MEDIA_GRP_ID_IC_PRPENC,
+	IMX_MEDIA_GRP_ID_VDIC,
+	IMX_MEDIA_GRP_ID_CSI,
+	IMX_MEDIA_GRP_ID_VIDMUX,
+	IMX_MEDIA_GRP_ID_SENSOR,
+	IMX_MEDIA_GRP_ID_CSI2,
+};
+
+#define NUM_POWER_ENTITIES ARRAY_SIZE(power_on_seq)
+
+static int imx_media_set_stream(struct imx_media_dev *imxmd,
+				struct media_entity *start_entity,
+				bool on)
+{
+	struct media_graph graph;
+	struct v4l2_subdev *sd;
+	int i, ret;
+	u32 id;
+
+	mutex_lock(&imxmd->md.graph_mutex);
+
+	ret = media_graph_walk_init(&graph, &imxmd->md);
+	if (ret)
+		goto unlock;
+
+	for (i = 0; i < NUM_STREAM_ENTITIES; i++) {
+		id = on ? stream_on_seq[i] : stream_off_seq[i];
+		sd = find_pipeline_subdev(imxmd, &graph,
+					  start_entity, id);
+		if (!sd)
+			continue;
+
+		ret = v4l2_subdev_call(sd, video, s_stream, on);
+		if (on && ret && ret != -ENOIOCTLCMD)
+			break;
+	}
+
+	media_graph_walk_cleanup(&graph);
+unlock:
+	mutex_unlock(&imxmd->md.graph_mutex);
+
+	return (on && ret && ret != -ENOIOCTLCMD) ? ret : 0;
+}
+
+/*
+ * Turn current pipeline streaming on/off starting from entity.
+ */
+int imx_media_pipeline_set_stream(struct imx_media_dev *imxmd,
+				  struct media_entity *entity,
+				  struct media_pipeline *pipe,
+				  bool on)
+{
+	int ret = 0;
+
+	if (on) {
+		ret = media_pipeline_start(entity, pipe);
+		if (ret)
+			return ret;
+		ret = imx_media_set_stream(imxmd, entity, true);
+		if (!ret)
+			return 0;
+		/* fall through */
+	}
+
+	imx_media_set_stream(imxmd, entity, false);
+	if (entity->pipe)
+		media_pipeline_stop(entity);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(imx_media_pipeline_set_stream);
+
+static int imx_media_set_power(struct imx_media_dev *imxmd,
+			       struct media_graph *graph,
+			       struct media_entity *start_entity, bool on)
+{
+	struct v4l2_subdev *sd;
+	int i, ret = 0;
+	u32 id;
+
+	for (i = 0; i < NUM_POWER_ENTITIES; i++) {
+		id = on ? power_on_seq[i] : power_off_seq[i];
+		sd = find_pipeline_subdev(imxmd, graph, start_entity, id);
+		if (!sd)
+			continue;
+
+		ret = v4l2_subdev_call(sd, core, s_power, on);
+		if (on && ret && ret != -ENOIOCTLCMD)
+			break;
+	}
+
+	return (on && ret && ret != -ENOIOCTLCMD) ? ret : 0;
+}
+
+/*
+ * Turn current pipeline power on/off starting from start_entity.
+ * Must be called with mdev->graph_mutex held.
+ */
+int imx_media_pipeline_set_power(struct imx_media_dev *imxmd,
+				 struct media_graph *graph,
+				 struct media_entity *start_entity, bool on)
+{
+	int ret;
+
+	ret = imx_media_set_power(imxmd, graph, start_entity, on);
+	if (ret)
+		imx_media_set_power(imxmd, graph, start_entity, false);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(imx_media_pipeline_set_power);
+
+MODULE_DESCRIPTION("i.MX5/6 v4l2 media controller driver");
+MODULE_AUTHOR("Steve Longerbeam <steve_longerbeam@mentor.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/staging/media/imx/imx-media.h b/drivers/staging/media/imx/imx-media.h
new file mode 100644
index 0000000..2dd48ea
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media.h
@@ -0,0 +1,303 @@
+/*
+ * V4L2 Media Controller Driver for Freescale i.MX5/6 SOC
+ *
+ * Copyright (c) 2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#ifndef _IMX_MEDIA_H
+#define _IMX_MEDIA_H
+
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-of.h>
+#include <media/v4l2-subdev.h>
+#include <media/videobuf2-dma-contig.h>
+#include <video/imx-ipu-v3.h>
+
+/*
+ * This is somewhat arbitrary, but we need at least:
+ * - 2 camera interface subdevs
+ * - 3 IC subdevs
+ * - 2 CSI subdevs
+ * - 1 mipi-csi2 receiver subdev
+ * - 2 video-mux subdevs
+ * - 3 camera sensor subdevs (2 parallel, 1 mipi-csi2)
+ *
+ * And double the above numbers for quad i.mx!
+ */
+#define IMX_MEDIA_MAX_SUBDEVS       48
+/* max pads per subdev */
+#define IMX_MEDIA_MAX_PADS          16
+/* max links per pad */
+#define IMX_MEDIA_MAX_LINKS          8
+
+/*
+ * Pad definitions for the subdevs with multiple source or
+ * sink pads
+ */
+/* ipu_csi */
+enum {
+	CSI_SINK_PAD = 0,
+	CSI_SRC_PAD_DIRECT,
+	CSI_SRC_PAD_IDMAC,
+	CSI_NUM_PADS,
+};
+
+#define CSI_NUM_SINK_PADS 1
+#define CSI_NUM_SRC_PADS  2
+
+/* ipu_vdic */
+enum {
+	VDIC_SINK_PAD_DIRECT = 0,
+	VDIC_SINK_PAD_IDMAC,
+	VDIC_SRC_PAD_DIRECT,
+	VDIC_NUM_PADS,
+};
+
+#define VDIC_NUM_SINK_PADS 2
+#define VDIC_NUM_SRC_PADS  1
+
+/* ipu_ic_prp */
+enum {
+	PRP_SINK_PAD = 0,
+	PRP_SRC_PAD_PRPENC,
+	PRP_SRC_PAD_PRPVF,
+	PRP_NUM_PADS,
+};
+
+#define PRP_NUM_SINK_PADS 1
+#define PRP_NUM_SRC_PADS  2
+
+/* ipu_ic_prpencvf */
+enum {
+	PRPENCVF_SINK_PAD = 0,
+	PRPENCVF_SRC_PAD,
+	PRPENCVF_NUM_PADS,
+};
+
+#define PRPENCVF_NUM_SINK_PADS 1
+#define PRPENCVF_NUM_SRC_PADS  1
+
+/* How long to wait for EOF interrupts in the buffer-capture subdevs */
+#define IMX_MEDIA_EOF_TIMEOUT       1000
+
+struct imx_media_pixfmt {
+	u32     fourcc;
+	u32     codes[4];
+	int     bpp;     /* total bpp */
+	enum ipu_color_space cs;
+	bool    planar;  /* is a planar format */
+	bool    ipufmt;  /* is one of the IPU internal formats */
+};
+
+struct imx_media_buffer {
+	struct vb2_v4l2_buffer vbuf; /* v4l buffer must be first */
+	struct list_head  list;
+};
+
+struct imx_media_video_dev {
+	struct video_device *vfd;
+
+	/* the user format */
+	struct v4l2_format fmt;
+	const struct imx_media_pixfmt *cc;
+};
+
+static inline struct imx_media_buffer *to_imx_media_vb(struct vb2_buffer *vb)
+{
+	struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb);
+
+	return container_of(vbuf, struct imx_media_buffer, vbuf);
+}
+
+struct imx_media_link {
+	struct device_node *remote_sd_node;
+	char               remote_devname[32];
+	int                local_pad;
+	int                remote_pad;
+};
+
+struct imx_media_pad {
+	struct media_pad  pad;
+	struct imx_media_link link[IMX_MEDIA_MAX_LINKS];
+	bool devnode; /* does this pad link to a device node */
+	int num_links;
+};
+
+struct imx_media_internal_sd_platformdata {
+	char sd_name[V4L2_SUBDEV_NAME_SIZE];
+	u32 grp_id;
+	int ipu_id;
+};
+
+struct imx_media_subdev {
+	struct v4l2_async_subdev asd;
+	struct v4l2_subdev       *sd; /* set when bound */
+
+	struct imx_media_pad     pad[IMX_MEDIA_MAX_PADS];
+	int num_sink_pads;
+	int num_src_pads;
+
+	/* the platform device if this is an internal subdev */
+	struct platform_device *pdev;
+	/* the devname is needed for async devname match */
+	char devname[32];
+
+	/* if this is a sensor */
+	struct v4l2_of_endpoint sensor_ep;
+};
+
+struct imx_media_dev {
+	struct media_device md;
+	struct v4l2_device  v4l2_dev;
+
+	/* master subdev list */
+	struct imx_media_subdev subdev[IMX_MEDIA_MAX_SUBDEVS];
+	int num_subdevs;
+
+	/* IPUs this media driver control, valid after subdevs bound */
+	struct ipu_soc *ipu[2];
+
+	/* used during link_notify */
+	struct media_graph link_notify_graph;
+
+	/* for async subdev registration */
+	struct v4l2_async_subdev *async_ptrs[IMX_MEDIA_MAX_SUBDEVS];
+	struct v4l2_async_notifier subdev_notifier;
+};
+
+const struct imx_media_pixfmt *imx_media_find_format(u32 fourcc, u32 code,
+						     bool allow_rgb,
+						     bool allow_planar);
+const struct imx_media_pixfmt *imx_media_find_ipu_format(u32 fourcc, u32 code,
+							 bool allow_rgb);
+
+int imx_media_enum_format(u32 *fourcc, u32 *code, u32 index,
+			  bool allow_rgb, bool allow_planar);
+int imx_media_enum_ipu_format(u32 *fourcc, u32 *code, u32 index,
+			      bool allow_rgb);
+
+int imx_media_init_mbus_fmt(struct v4l2_mbus_framefmt *mbus,
+			    u32 width, u32 height, u32 code, u32 field,
+			    const struct imx_media_pixfmt **cc);
+
+int imx_media_mbus_fmt_to_pix_fmt(struct v4l2_pix_format *pix,
+				  struct v4l2_mbus_framefmt *mbus,
+				  const struct imx_media_pixfmt *cc);
+int imx_media_mbus_fmt_to_ipu_image(struct ipu_image *image,
+				    struct v4l2_mbus_framefmt *mbus);
+int imx_media_ipu_image_to_mbus_fmt(struct v4l2_mbus_framefmt *mbus,
+				    struct ipu_image *image);
+
+struct imx_media_subdev *
+imx_media_find_async_subdev(struct imx_media_dev *imxmd,
+			    struct device_node *np,
+			    const char *devname);
+struct imx_media_subdev *
+imx_media_add_async_subdev(struct imx_media_dev *imxmd,
+			   struct device_node *np,
+			   struct platform_device *pdev);
+int imx_media_add_pad_link(struct imx_media_dev *imxmd,
+			   struct imx_media_pad *pad,
+			   struct device_node *remote_node,
+			   const char *remote_devname,
+			   int local_pad, int remote_pad);
+
+void imx_media_grp_id_to_sd_name(char *sd_name, int sz,
+				 u32 grp_id, int ipu_id);
+
+int imx_media_add_internal_subdevs(struct imx_media_dev *imxmd,
+				   struct imx_media_subdev *csi[4]);
+void imx_media_remove_internal_subdevs(struct imx_media_dev *imxmd);
+
+struct imx_media_subdev *
+imx_media_find_subdev_by_sd(struct imx_media_dev *imxmd,
+			    struct v4l2_subdev *sd);
+struct imx_media_subdev *
+imx_media_find_subdev_by_id(struct imx_media_dev *imxmd,
+			    u32 grp_id);
+int imx_media_find_mipi_csi2_channel(struct imx_media_dev *imxmd,
+				     struct media_entity *start_entity);
+struct imx_media_subdev *
+imx_media_find_pipeline_subdev(struct imx_media_dev *imxmd,
+			       struct media_entity *start_entity,
+			       u32 grp_id);
+struct video_device *
+imx_media_find_pipeline_video_device(struct imx_media_dev *imxmd,
+				     struct media_entity *start_entity);
+struct imx_media_subdev *
+__imx_media_find_sensor(struct imx_media_dev *imxmd,
+			struct media_entity *start_entity);
+struct imx_media_subdev *
+imx_media_find_sensor(struct imx_media_dev *imxmd,
+		      struct media_entity *start_entity);
+
+struct imx_media_dma_buf {
+	void          *virt;
+	dma_addr_t     phys;
+	unsigned long  len;
+};
+
+void imx_media_free_dma_buf(struct imx_media_dev *imxmd,
+			    struct imx_media_dma_buf *buf);
+int imx_media_alloc_dma_buf(struct imx_media_dev *imxmd,
+			    struct imx_media_dma_buf *buf,
+			    int size);
+
+int imx_media_pipeline_set_power(struct imx_media_dev *imxmd,
+				 struct media_graph *graph,
+				 struct media_entity *entity, bool on);
+int imx_media_pipeline_set_stream(struct imx_media_dev *imxmd,
+				  struct media_entity *entity,
+				  struct media_pipeline *pipe,
+				  bool on);
+
+/* imx-media-fim.c */
+struct imx_media_fim;
+void imx_media_fim_eof_monitor(struct imx_media_fim *fim, struct timespec *ts);
+int imx_media_fim_set_power(struct imx_media_fim *fim, bool on);
+int imx_media_fim_set_stream(struct imx_media_fim *fim,
+			     struct imx_media_subdev *sensor,
+			     bool on);
+struct imx_media_fim *imx_media_fim_init(struct v4l2_subdev *sd);
+void imx_media_fim_free(struct imx_media_fim *fim);
+
+/* imx-media-of.c */
+struct imx_media_subdev *
+imx_media_of_find_subdev(struct imx_media_dev *imxmd,
+			 struct device_node *np,
+			 const char *name);
+int imx_media_of_parse(struct imx_media_dev *dev,
+		       struct imx_media_subdev *(*csi)[4],
+		       struct device_node *np);
+
+/* imx-media-capture.c */
+struct imx_media_video_dev *
+imx_media_capture_device_init(struct v4l2_subdev *src_sd, int pad);
+void imx_media_capture_device_remove(struct imx_media_video_dev *vdev);
+int imx_media_capture_device_register(struct imx_media_video_dev *vdev);
+void imx_media_capture_device_unregister(struct imx_media_video_dev *vdev);
+struct imx_media_buffer *
+imx_media_capture_device_next_buf(struct imx_media_video_dev *vdev);
+void imx_media_capture_device_set_format(struct imx_media_video_dev *vdev,
+					 struct v4l2_pix_format *pix);
+void imx_media_capture_device_error(struct imx_media_video_dev *vdev);
+
+/* subdev group ids */
+#define IMX_MEDIA_GRP_ID_SENSOR    (1 << 8)
+#define IMX_MEDIA_GRP_ID_VIDMUX    (1 << 9)
+#define IMX_MEDIA_GRP_ID_CSI2      (1 << 10)
+#define IMX_MEDIA_GRP_ID_CSI_BIT   11
+#define IMX_MEDIA_GRP_ID_CSI       (0x3 << IMX_MEDIA_GRP_ID_CSI_BIT)
+#define IMX_MEDIA_GRP_ID_CSI0      (1 << IMX_MEDIA_GRP_ID_CSI_BIT)
+#define IMX_MEDIA_GRP_ID_CSI1      (2 << IMX_MEDIA_GRP_ID_CSI_BIT)
+#define IMX_MEDIA_GRP_ID_VDIC      (1 << 13)
+#define IMX_MEDIA_GRP_ID_IC_PRP    (1 << 14)
+#define IMX_MEDIA_GRP_ID_IC_PRPENC (1 << 15)
+#define IMX_MEDIA_GRP_ID_IC_PRPVF  (1 << 16)
+
+#endif
diff --git a/include/media/imx.h b/include/media/imx.h
new file mode 100644
index 0000000..5025a72
--- /dev/null
+++ b/include/media/imx.h
@@ -0,0 +1,15 @@
+/*
+ * Copyright (c) 2014-2015 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version
+ */
+
+#ifndef __MEDIA_IMX_H__
+#define __MEDIA_IMX_H__
+
+#include <uapi/media/imx.h>
+
+#endif
diff --git a/include/uapi/linux/v4l2-controls.h b/include/uapi/linux/v4l2-controls.h
index 0d2e1e0..6c29f42 100644
--- a/include/uapi/linux/v4l2-controls.h
+++ b/include/uapi/linux/v4l2-controls.h
@@ -180,6 +180,10 @@ enum v4l2_colorfx {
  * We reserve 16 controls for this driver. */
 #define V4L2_CID_USER_TC358743_BASE		(V4L2_CID_USER_BASE + 0x1080)
 
+/* The base for the imx driver controls.
+ * We reserve 16 controls for this driver. */
+#define V4L2_CID_USER_IMX_BASE			(V4L2_CID_USER_BASE + 0x1090)
+
 /* MPEG-class control IDs */
 /* The MPEG controls are applicable to all codec controls
  * and the 'MPEG' part of the define is historical */
-- 
2.7.4

[PATCH v5 23/39] media: Add i.MX media core driver

[Steve Longerbeam]

Add the core media driver for i.MX SOC.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 Documentation/media/v4l-drivers/imx.rst           | 560 ++++++++++++++++
 drivers/staging/media/Kconfig                     |   2 +
 drivers/staging/media/Makefile                    |   1 +
 drivers/staging/media/imx/Kconfig                 |   6 +
 drivers/staging/media/imx/Makefile                |   5 +
 drivers/staging/media/imx/TODO                    |  17 +
 drivers/staging/media/imx/imx-media-dev.c         | 522 +++++++++++++++
 drivers/staging/media/imx/imx-media-fim.c         | 471 +++++++++++++
 drivers/staging/media/imx/imx-media-internal-sd.c | 349 ++++++++++
 drivers/staging/media/imx/imx-media-of.c          | 267 ++++++++
 drivers/staging/media/imx/imx-media-utils.c       | 766 ++++++++++++++++++++++
 drivers/staging/media/imx/imx-media.h             | 303 +++++++++
 include/media/imx.h                               |  15 +
 include/uapi/linux/v4l2-controls.h                |   4 +
 14 files changed, 3288 insertions(+)
 create mode 100644 Documentation/media/v4l-drivers/imx.rst
 create mode 100644 drivers/staging/media/imx/Kconfig
 create mode 100644 drivers/staging/media/imx/Makefile
 create mode 100644 drivers/staging/media/imx/TODO
 create mode 100644 drivers/staging/media/imx/imx-media-dev.c
 create mode 100644 drivers/staging/media/imx/imx-media-fim.c
 create mode 100644 drivers/staging/media/imx/imx-media-internal-sd.c
 create mode 100644 drivers/staging/media/imx/imx-media-of.c
 create mode 100644 drivers/staging/media/imx/imx-media-utils.c
 create mode 100644 drivers/staging/media/imx/imx-media.h
 create mode 100644 include/media/imx.h

diff --git a/Documentation/media/v4l-drivers/imx.rst b/Documentation/media/v4l-drivers/imx.rst
new file mode 100644
index 0000000..443e0d0
--- /dev/null
+++ b/Documentation/media/v4l-drivers/imx.rst
@@ -0,0 +1,560 @@
+i.MX Video Capture Driver
+=========================
+
+Introduction
+------------
+
+The Freescale i.MX5/6 contains an Image Processing Unit (IPU), which
+handles the flow of image frames to and from capture devices and
+display devices.
+
+For image capture, the IPU contains the following internal subunits:
+
+- Image DMA Controller (IDMAC)
+- Camera Serial Interface (CSI)
+- Image Converter (IC)
+- Sensor Multi-FIFO Controller (SMFC)
+- Image Rotator (IRT)
+- Video De-Interlacing or Combining Block (VDIC)
+
+The IDMAC is the DMA controller for transfer of image frames to and from
+memory. Various dedicated DMA channels exist for both video capture and
+display paths. During transfer, the IDMAC is also capable of vertical
+image flip, 8x8 block transfer (see IRT description), pixel component
+re-ordering (for example UYVY to YUYV) within the same colorspace, and
+even packed <--> planar conversion. It can also perform a simple
+de-interlacing by interleaving even and odd lines during transfer
+(without motion compensation which requires the VDIC).
+
+The CSI is the backend capture unit that interfaces directly with
+camera sensors over Parallel, BT.656/1120, and MIPI CSI-2 busses.
+
+The IC handles color-space conversion, resizing (downscaling and
+upscaling), horizontal flip, and 90/270 degree rotation operations.
+
+There are three independent "tasks" within the IC that can carry out
+conversions concurrently: pre-process encoding, pre-process viewfinder,
+and post-processing. Within each task, conversions are split into three
+sections: downsizing section, main section (upsizing, flip, colorspace
+conversion, and graphics plane combining), and rotation section.
+
+The IPU time-shares the IC task operations. The time-slice granularity
+is one burst of eight pixels in the downsizing section, one image line
+in the main processing section, one image frame in the rotation section.
+
+The SMFC is composed of four independent FIFOs that each can transfer
+captured frames from sensors directly to memory concurrently via four
+IDMAC channels.
+
+The IRT carries out 90 and 270 degree image rotation operations. The
+rotation operation is carried out on 8x8 pixel blocks at a time. This
+operation is supported by the IDMAC which handles the 8x8 block transfer
+along with block reordering, in coordination with vertical flip.
+
+The VDIC handles the conversion of interlaced video to progressive, with
+support for different motion compensation modes (low, medium, and high
+motion). The deinterlaced output frames from the VDIC can be sent to the
+IC pre-process viewfinder task for further conversions. The VDIC also
+contains a Combiner that combines two image planes, with alpha blending
+and color keying.
+
+In addition to the IPU internal subunits, there are also two units
+outside the IPU that are also involved in video capture on i.MX:
+
+- MIPI CSI-2 Receiver for camera sensors with the MIPI CSI-2 bus
+  interface. This is a Synopsys DesignWare core.
+- Two video multiplexers for selecting among multiple sensor inputs
+  to send to a CSI.
+
+For more info, refer to the latest versions of the i.MX5/6 reference
+manuals listed under References.
+
+
+Features
+--------
+
+Some of the features of this driver include:
+
+- Many different pipelines can be configured via media controller API,
+  that correspond to the hardware video capture pipelines supported in
+  the i.MX.
+
+- Supports parallel, BT.565, and MIPI CSI-2 interfaces.
+
+- Up to four concurrent sensor acquisitions, by configuring each
+  sensor's pipeline using independent entities. This is currently
+  demonstrated with the SabreSD and SabreLite reference boards with
+  independent OV5642 and MIPI CSI-2 OV5640 sensor modules.
+
+- Scaling, color-space conversion, horizontal and vertical flip, and
+  image rotation via IC task subdevs.
+
+- Many pixel formats supported (RGB, packed and planar YUV, partial
+  planar YUV).
+
+- The VDIC subdev supports motion compensated de-interlacing, with three
+  motion compensation modes: low, medium, and high motion. Pipelines are
+  defined that allow sending frames to the VDIC subdev directly from the
+  CSI or from memory buffers via an output/mem2mem device node. For low
+  and medium motion modes, the VDIC must receive from memory buffers via
+  a device node.
+
+- Includes a Frame Interval Monitor (FIM) that can correct vertical sync
+  problems with the ADV718x video decoders. See below for a description
+  of the FIM.
+
+
+Entities
+--------
+
+imx6-mipi-csi2
+--------------
+
+This is the MIPI CSI-2 receiver entity. It has one sink pad to receive
+the MIPI CSI-2 stream (usually from a MIPI CSI-2 camera sensor). It has
+four source pads, corresponding to the four MIPI CSI-2 demuxed virtual
+channel outputs.
+
+This entity actually consists of two sub-blocks. One is the MIPI CSI-2
+core. This is a Synopsys Designware MIPI CSI-2 core. The other sub-block
+is a "CSI-2 to IPU gasket". The gasket acts as a demultiplexer of the
+four virtual channels streams, providing four separate parallel buses
+containing each virtual channel that are routed to CSIs or video
+multiplexers as described below.
+
+On i.MX6 solo/dual-lite, all four virtual channel buses are routed to
+two video multiplexers. Both CSI0 and CSI1 can receive any virtual
+channel, as selected by the video multiplexers.
+
+On i.MX6 Quad, virtual channel 0 is routed to IPU1-CSI0 (after selected
+by a video mux), virtual channels 1 and 2 are hard-wired to IPU1-CSI1
+and IPU2-CSI0, respectively, and virtual channel 3 is routed to
+IPU2-CSI1 (again selected by a video mux).
+
+ipuX_csiY_mux
+-------------
+
+These are the video multiplexers. They have two or more sink pads to
+select from either camera sensors with a parallel interface, or from
+MIPI CSI-2 virtual channels from imx6-mipi-csi2 entity. They have a
+single source pad that routes to a CSI (ipuX_csiY entities).
+
+On i.MX6 solo/dual-lite, there are two video mux entities. One sits
+in front of IPU1-CSI0 to select between a parallel sensor and any of
+the four MIPI CSI-2 virtual channels (a total of five sink pads). The
+other mux sits in front of IPU1-CSI1, and again has five sink pads to
+select between a parallel sensor and any of the four MIPI CSI-2 virtual
+channels.
+
+On i.MX6 Quad, there are two video mux entities. One sits in front of
+IPU1-CSI0 to select between a parallel sensor and MIPI CSI-2 virtual
+channel 0 (two sink pads). The other mux sits in front of IPU2-CSI1 to
+select between a parallel sensor and MIPI CSI-2 virtual channel 3 (two
+sink pads).
+
+ipuX_csiY
+---------
+
+These are the CSI entities. They have a single sink pad receiving from
+either a video mux or from a MIPI CSI-2 virtual channel as described
+above.
+
+This entity has two source pads. The first source pad can link directly
+to the ipuX_vdic entity or the ipuX_ic_prp entity, using hardware links
+that require no IDMAC memory buffer transfer.
+
+When the direct source pad is routed to the ipuX_ic_prp entity, frames
+from the CSI will be processed by one of the IC pre-processing tasks.
+
+When the direct source pad is routed to the ipuX_vdic entity, the VDIC
+will carry out motion-compensated de-interlace using "high motion" mode
+(see description of ipuX_vdic entity).
+
+The second source pad sends video frames to memory buffers via the SMFC
+and an IDMAC channel. This source pad is routed to a capture device
+node.
+
+Note that since the IDMAC source pad makes use of an IDMAC channel, it
+can do pixel reordering within the same colorspace. For example, the
+sink pad can take UYVY2X8, but the IDMAC source pad can output YUYV2X8.
+If the sink pad is receiving YUV, the output at the capture device can
+also be converted to a planar YUV format such as YUV420.
+
+It will also perform simple de-interlace without motion compensation,
+which is activated if the sink pad's field type is an interlaced type,
+and the IDMAC source pad field type is set to none.
+
+This subdev can generate two types of events:
+
+- V4L2_EVENT_NEW_FRAME_BEFORE_EOF
+- V4L2_EVENT_FRAME_INTERVAL_ERROR
+
+The user application can subscribe to these events from the ipuX_csiY
+subdev node. The V4L2_EVENT_FRAME_INTERVAL_ERROR event is generated
+by the Frame Interval Monitor (see below for more on the FIM).
+
+ipuX_vdic
+---------
+
+The VDIC carries out motion compensated de-interlacing, with three
+motion compensation modes: low, medium, and high motion. The mode is
+specified with the menu control V4L2_CID_DEINTERLACING_MODE. It has
+two sink pads and a single source pad.
+
+The direct sink pad receives from an ipuX_csiY direct pad. With this
+link the VDIC can only operate in high motion mode.
+
+When the IDMAC sink pad is activated, it receives from an output
+or mem2mem device node. With this pipeline, it can also operate
+in low and medium modes, because these modes require receiving
+frames from memory buffers. Note that an output or mem2mem device
+is not implemented yet, so this sink pad currently has no links.
+
+The source pad routes to the IC pre-processing entity ipuX_ic_prp.
+
+ipuX_ic_prp
+-----------
+
+This is the IC pre-processing entity. It acts as a router, routing
+data from its sink pad to one or both of its source pads.
+
+It has a single sink pad. The sink pad can receive from the ipuX_csiY
+direct pad, or from ipuX_vdic.
+
+This entity has two source pads. One source pad routes to the
+pre-process encode task entity (ipuX_ic_prpenc), the other to the
+pre-process viewfinder task entity (ipuX_ic_prpvf). Both source pads
+can be activated at the same time if the sink pad is receiving from
+ipuX_csiY. Only the source pad to the pre-process viewfinder task entity
+can be activated if the sink pad is receiving from ipuX_vdic (frames
+from the VDIC can only be processed by the pre-process viewfinder task).
+
+ipuX_ic_prpenc
+--------------
+
+This is the IC pre-processing encode entity. It has a single sink pad
+from ipuX_ic_prp, and a single source pad. The source pad is routed
+to a capture device node.
+
+This entity performs the IC pre-process encode task operations:
+color-space conversion, resizing (downscaling and upscaling), horizontal
+and vertical flip, and 90/270 degree rotation.
+
+Like the ipuX_csiY IDMAC source, it can also perform simple de-interlace
+without motion compensation, and pixel reordering.
+
+This subdev can generate the V4L2_EVENT_NEW_FRAME_BEFORE_EOF event, and
+can be subscribed to from the ipuX_ic_prpenc subdev node.
+
+ipuX_ic_prpvf
+-------------
+
+This is the IC pre-processing viewfinder entity. It has a single sink pad
+from ipuX_ic_prp, and a single source pad. The source pad is routed to
+a capture device node.
+
+It is identical in operation to ipuX_ic_prpenc. It will receive and
+process de-interlaced frames from the ipuX_vdic if ipuX_ic_prp is
+receiving from ipuX_vdic.
+
+Like the ipuX_csiY IDMAC source, it can perform simple de-interlace
+without motion compensation. However, note that if the ipuX_vdic is
+included in the pipeline (ipuX_ic_prp is receiving from ipuX_vdic),
+it's not possible to use simple de-interlace in ipuX_ic_prpvf, since
+the ipuX_vdic has already carried out de-interlacing (with motion
+compensation) and therefore the field type output from ipuX_ic_prp can
+only be none.
+
+This subdev can generate the V4L2_EVENT_NEW_FRAME_BEFORE_EOF event, and
+can be subscribed to from the ipuX_ic_prpvf subdev node.
+
+Capture Pipelines
+-----------------
+
+The following describe the various use-cases supported by the pipelines.
+
+The links shown do not include the backend sensor, video mux, or mipi
+csi-2 receiver links. This depends on the type of sensor interface
+(parallel or mipi csi-2). So in all cases, these pipelines begin with:
+
+sensor -> ipuX_csiY_mux -> ...
+
+for parallel sensors, or:
+
+sensor -> imx6-mipi-csi2 -> (ipuX_csiY_mux) -> ...
+
+for mipi csi-2 sensors. The imx6-mipi-csi2 receiver may need to route
+to the video mux (ipuX_csiY_mux) before sending to the CSI, depending
+on the mipi csi-2 virtual channel, hence ipuX_csiY_mux is shown in
+parenthesis.
+
+Unprocessed Video Capture:
+--------------------------
+
+Send frames directly from sensor to camera device interface node, with
+no conversions:
+
+-> ipuX_csiY IDMAC pad -> capture node
+
+IC Direct Conversions:
+----------------------
+
+This pipeline uses the preprocess encode entity to route frames directly
+from the CSI to the IC, to carry out scaling up to 1024x1024 resolution,
+CSC, flipping, and image rotation:
+
+-> ipuX_csiY direct pad -> ipuX_ic_prp -> ipuX_ic_prpenc -> capture node
+
+Motion Compensated De-interlace:
+--------------------------------
+
+This pipeline routes frames from the CSI direct pad to the VDIC entity to
+support motion-compensated de-interlacing (high motion mode only),
+scaling up to 1024x1024, CSC, flip, and rotation:
+
+-> ipuX_csiY direct pad -> ipuX_vdic direct pad -> ipuX_ic_prp ->
+   ipuX_ic_prpvf -> capture node
+
+
+Usage Notes
+-----------
+
+Many of the subdevs require information from the active sensor in the
+current pipeline when configuring pad formats. Therefore the media links
+should be established before configuring the media pad formats.
+
+Similarly, the capture device interfaces inherit controls from the
+active entities in the current pipeline at link-setup time. Therefore
+the capture device node links should be the last links established in
+order for the capture interfaces to "see" and inherit all possible
+controls.
+
+The following are usage notes for Sabre- reference platforms:
+
+
+SabreLite with OV5642 and OV5640
+--------------------------------
+
+This platform requires the OmniVision OV5642 module with a parallel
+camera interface, and the OV5640 module with a MIPI CSI-2
+interface. Both modules are available from Boundary Devices:
+
+https://boundarydevices.com/products/nit6x_5mp
+https://boundarydevices.com/product/nit6x_5mp_mipi
+
+Note that if only one camera module is available, the other sensor
+node can be disabled in the device tree.
+
+The OV5642 module is connected to the parallel bus input on the i.MX
+internal video mux to IPU1 CSI0. It's i2c bus connects to i2c bus 2.
+
+The MIPI CSI-2 OV5640 module is connected to the i.MX internal MIPI CSI-2
+receiver, and the four virtual channel outputs from the receiver are
+routed as follows: vc0 to the IPU1 CSI0 mux, vc1 directly to IPU1 CSI1,
+vc2 directly to IPU2 CSI0, and vc3 to the IPU2 CSI1 mux. The OV5640 is
+also connected to i2c bus 2 on the SabreLite, therefore the OV5642 and
+OV5640 must not share the same i2c slave address.
+
+The following basic example configures unprocessed video capture
+pipelines for both sensors. The OV5642 is routed to ipu1_csi0, and
+the OV5640 (transmitting on mipi csi-2 virtual channel 1) is routed
+to ipu1_csi1. Both sensors are configured to output 640x480, the
+OV5642 outputs YUYV2X8, the OV5640 UYVY2X8:
+
+.. code-block:: none
+
+   # Setup links for OV5642
+   media-ctl -l '"ov5642 1-0042":0 -> "ipu1_csi0_mux":1[1]'
+   media-ctl -l '"ipu1_csi0_mux":2 -> "ipu1_csi0":0[1]'
+   media-ctl -l '"ipu1_csi0":2 -> "ipu1_csi0 capture":0[1]'
+   # Setup links for OV5640
+   media-ctl -l '"ov5640 1-0040":0 -> "imx6-mipi-csi2":0[1]'
+   media-ctl -l '"imx6-mipi-csi2":2 -> "ipu1_csi1":0[1]'
+   media-ctl -l '"ipu1_csi1":2 -> "ipu1_csi1 capture":0[1]'
+   # Configure pads for OV5642 pipeline
+   media-ctl -V "\"ov5642 1-0042\":0 [fmt:YUYV2X8/640x480 field:none]"
+   media-ctl -V "\"ipu1_csi0_mux\":2 [fmt:YUYV2X8/640x480 field:none]"
+   media-ctl -V "\"ipu1_csi0\":2 [fmt:AYUV32/640x480 field:none]"
+   # Configure pads for OV5640 pipeline
+   media-ctl -V "\"ov5640 1-0040\":0 [fmt:UYVY2X8/640x480 field:none]"
+   media-ctl -V "\"imx6-mipi-csi2\":2 [fmt:UYVY2X8/640x480 field:none]"
+   media-ctl -V "\"ipu1_csi1\":2 [fmt:AYUV32/640x480 field:none]"
+
+Streaming can then begin independently on the capture device nodes
+"ipu1_csi0 capture" and "ipu1_csi1 capture". The v4l2-ctl tool can
+be used to select any supported YUV pixelformat on the capture device
+nodes, including planar.
+
+SabreAuto with ADV7180 decoder
+------------------------------
+
+On the SabreAuto, an on-board ADV7180 SD decoder is connected to the
+parallel bus input on the internal video mux to IPU1 CSI0.
+
+The following example configures a pipeline to capture from the ADV7180
+video decoder, assuming NTSC 720x480 input signals, with Motion
+Compensated de-interlacing. Pad field types assume the adv7180 outputs
+"alternate", which the ipu1_csi0 entity converts to "seq-tb" at its
+source pad. $outputfmt can be any format supported by the ipu1_ic_prpvf
+entity at its output pad:
+
+.. code-block:: none
+
+   # Setup links
+   media-ctl -l '"adv7180 4-0021":0 -> "ipu1_csi0_mux":1[1]'
+   media-ctl -l '"ipu1_csi0_mux":2 -> "ipu1_csi0":0[1]'
+   media-ctl -l '"ipu1_csi0":1 -> "ipu1_vdic":0[1]'
+   media-ctl -l '"ipu1_vdic":2 -> "ipu1_ic_prp":0[1]'
+   media-ctl -l '"ipu1_ic_prp":2 -> "ipu1_ic_prpvf":0[1]'
+   media-ctl -l '"ipu1_ic_prpvf":1 -> "ipu1_ic_prpvf capture":0[1]'
+   # Configure pads
+   media-ctl -V "\"adv7180 4-0021\":0 [fmt:UYVY2X8/720x480]"
+   media-ctl -V "\"ipu1_csi0_mux\":2 [fmt:UYVY2X8/720x480 field:alternate]"
+   media-ctl -V "\"ipu1_csi0\":1 [fmt:AYUV32/720x480 field:seq-tb]"
+   media-ctl -V "\"ipu1_vdic\":2 [fmt:AYUV32/720x480 field:none]"
+   media-ctl -V "\"ipu1_ic_prp\":2 [fmt:AYUV32/720x480 field:none]"
+   media-ctl -V "\"ipu1_ic_prpvf\":1 [fmt:$outputfmt field:none]"
+
+Streaming can then begin on the capture device node at
+"ipu1_ic_prpvf capture". The v4l2-ctl tool can be used to select any
+supported YUV or RGB pixelformat on the capture device node.
+
+This platform accepts Composite Video analog inputs to the ADV7180 on
+Ain1 (connector J42).
+
+Frame Interval Monitor
+----------------------
+
+The adv718x decoders can occasionally send corrupt fields during
+NTSC/PAL signal re-sync (too little or too many video lines). When
+this happens, the IPU triggers a mechanism to re-establish vertical
+sync by adding 1 dummy line every frame, which causes a rolling effect
+from image to image, and can last a long time before a stable image is
+recovered. Or sometimes the mechanism doesn't work at all, causing a
+permanent split image (one frame contains lines from two consecutive
+captured images).
+
+From experiment it was found that during image rolling, the frame
+intervals (elapsed time between two EOF's) drop below the nominal
+value for the current standard, by about one frame time (60 usec),
+and remain at that value until rolling stops.
+
+While the reason for this observation isn't known (the IPU dummy
+line mechanism should show an increase in the intervals by 1 line
+time every frame, not a fixed value), we can use it to detect the
+corrupt fields using a frame interval monitor. If the FIM detects a
+bad frame interval, a subdev event is sent. In response, userland can
+issue a streaming restart to correct the rolling/split image.
+
+The FIM is implemented in the ipuX_csiY entity, and the entities that
+generate End-Of-Frame interrupts call into the FIM to monitor the frame
+intervals: ipuX_ic_prpenc, and ipuX_ic_prpvf. Userland can register with
+the FIM event notifications on the ipuX_csiY subdev device node
+(V4L2_EVENT_FRAME_INTERVAL_ERROR).
+
+The ipuX_csiY entity includes custom controls to tweak some dials for
+FIM. If one of these controls is changed during streaming, the FIM will
+be reset and will continue at the new settings.
+
+- V4L2_CID_IMX_FIM_ENABLE
+
+Enable/disable the FIM.
+
+- V4L2_CID_IMX_FIM_NUM
+
+How many frame interval errors to average before comparing against the
+nominal frame interval reported by the sensor. This can reduce noise
+from interrupt latency.
+
+- V4L2_CID_IMX_FIM_TOLERANCE_MIN
+
+If the averaged intervals fall outside nominal by this amount, in
+microseconds, streaming will be restarted.
+
+- V4L2_CID_IMX_FIM_TOLERANCE_MAX
+
+If any interval errors are higher than this value, those error samples
+are discarded and do not enter into the average. This can be used to
+discard really high interval errors that might be due to very high
+system load, causing excessive interrupt latencies.
+
+- V4L2_CID_IMX_FIM_NUM_SKIP
+
+How many frames to skip after a FIM reset or stream restart before
+FIM begins to average intervals. It has been found that there can
+be a few bad frame intervals after stream restart which are not
+attributed to adv718x sending a corrupt field, so this is used to
+skip those frames to prevent unnecessary restarts.
+
+
+SabreSD with MIPI CSI-2 OV5640
+------------------------------
+
+Similarly to SabreLite, the SabreSD supports a parallel interface
+OV5642 module on IPU1 CSI0, and a MIPI CSI-2 OV5640 module. The OV5642
+connects to i2c bus 1 and the OV5640 to i2c bus 2.
+
+The device tree for SabreSD includes OF graphs for both the parallel
+OV5642 and the MIPI CSI-2 OV5640, but as of this writing only the MIPI
+CSI-2 OV5640 has been tested, so the OV5642 node is currently disabled.
+The OV5640 module connects to MIPI connector J5 (sorry I don't have the
+compatible module part number or URL).
+
+The following example configures a direct conversion pipeline to capture
+from the OV5640. $sensorfmt can be any format supported by the OV5640.
+$sensordim is the frame dimension part of $sensorfmt (minus the mbus
+pixel code). $outputfmt can be any format supported by the
+ipu1_ic_prpenc entity at its output pad:
+
+.. code-block:: none
+
+   # Setup links
+   media-ctl -l '"ov5640 1-003c":0 -> "imx6-mipi-csi2":0[1]'
+   media-ctl -l '"imx6-mipi-csi2":2 -> "ipu1_csi1":0[1]'
+   media-ctl -l '"ipu1_csi1":1 -> "ipu1_ic_prp":0[1]'
+   media-ctl -l '"ipu1_ic_prp":1 -> "ipu1_ic_prpenc":0[1]'
+   media-ctl -l '"ipu1_ic_prpenc":1 -> "ipu1_ic_prpenc capture":0[1]'
+   # Configure pads
+   media-ctl -V "\"ov5640 1-003c\":0 [fmt:$sensorfmt field:none]"
+   media-ctl -V "\"imx6-mipi-csi2\":2 [fmt:$sensorfmt field:none]"
+   media-ctl -V "\"ipu1_csi1\":1 [fmt:AYUV32/$sensordim field:none]"
+   media-ctl -V "\"ipu1_ic_prp\":1 [fmt:AYUV32/$sensordim field:none]"
+   media-ctl -V "\"ipu1_ic_prpenc\":1 [fmt:$outputfmt field:none]"
+
+Streaming can then begin on "ipu1_ic_prpenc capture" node. The v4l2-ctl
+tool can be used to select any supported YUV or RGB pixelformat on the
+capture device node.
+
+
+Known Issues
+------------
+
+1. When using 90 or 270 degree rotation control at capture resolutions
+   near the IC resizer limit of 1024x1024, and combined with planar
+   pixel formats (YUV420, YUV422p), frame capture will often fail with
+   no end-of-frame interrupts from the IDMAC channel. To work around
+   this, use lower resolution and/or packed formats (YUYV, RGB3, etc.)
+   when 90 or 270 rotations are needed.
+
+
+File list
+---------
+
+drivers/staging/media/imx/
+include/media/imx.h
+include/uapi/media/imx.h
+
+References
+----------
+
+[1] "i.MX 6Dual/6Quad Applications Processor Reference Manual"
+[2] "i.MX 6Solo/6DualLite Applications Processor Reference Manual"
+
+
+Authors
+-------
+Steve Longerbeam <steve_longerbeam@mentor.com>
+Philipp Zabel <kernel@pengutronix.de>
+Russell King <linux@armlinux.org.uk>
+
+Copyright (C) 2012-2017 Mentor Graphics Inc.
diff --git a/drivers/staging/media/Kconfig b/drivers/staging/media/Kconfig
index abd0e2d..31af2a0 100644
--- a/drivers/staging/media/Kconfig
+++ b/drivers/staging/media/Kconfig
@@ -25,6 +25,8 @@ source "drivers/staging/media/cxd2099/Kconfig"
 
 source "drivers/staging/media/davinci_vpfe/Kconfig"
 
+source "drivers/staging/media/imx/Kconfig"
+
 source "drivers/staging/media/omap4iss/Kconfig"
 
 source "drivers/staging/media/platform/bcm2835/Kconfig"
diff --git a/drivers/staging/media/Makefile b/drivers/staging/media/Makefile
index dc89325..0bfb65d 100644
--- a/drivers/staging/media/Makefile
+++ b/drivers/staging/media/Makefile
@@ -1,6 +1,7 @@
 obj-$(CONFIG_I2C_BCM2048)	+= bcm2048/
 obj-$(CONFIG_VIDEO_SAMSUNG_S5P_CEC) += s5p-cec/
 obj-$(CONFIG_DVB_CXD2099)	+= cxd2099/
+obj-$(CONFIG_VIDEO_IMX_MEDIA)	+= imx/
 obj-$(CONFIG_LIRC_STAGING)	+= lirc/
 obj-$(CONFIG_VIDEO_BCM2835)	+= platform/bcm2835/
 obj-$(CONFIG_VIDEO_DM365_VPFE)	+= davinci_vpfe/
diff --git a/drivers/staging/media/imx/Kconfig b/drivers/staging/media/imx/Kconfig
new file mode 100644
index 0000000..62a3c34
--- /dev/null
+++ b/drivers/staging/media/imx/Kconfig
@@ -0,0 +1,6 @@
+config VIDEO_IMX_MEDIA
+	tristate "i.MX5/6 V4L2 media core driver"
+	depends on MEDIA_CONTROLLER && VIDEO_V4L2 && ARCH_MXC && IMX_IPUV3_CORE
+	---help---
+	  Say yes here to enable support for video4linux media controller
+	  driver for the i.MX5/6 SOC.
diff --git a/drivers/staging/media/imx/Makefile b/drivers/staging/media/imx/Makefile
new file mode 100644
index 0000000..ddd7d94
--- /dev/null
+++ b/drivers/staging/media/imx/Makefile
@@ -0,0 +1,5 @@
+imx-media-objs := imx-media-dev.o imx-media-internal-sd.o imx-media-of.o
+imx-media-common-objs := imx-media-utils.o imx-media-fim.o
+
+obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media.o
+obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-common.o
diff --git a/drivers/staging/media/imx/TODO b/drivers/staging/media/imx/TODO
new file mode 100644
index 0000000..78f78fa
--- /dev/null
+++ b/drivers/staging/media/imx/TODO
@@ -0,0 +1,17 @@
+
+- Finish v4l2-compliance
+
+- Clean up and move the ov5642 subdev driver to drivers/media/i2c, and
+  create the binding docs for it.
+
+- The Frame Interval Monitor could be exported to v4l2-core for
+  general use.
+
+- At driver load time, the device-tree node that is the original source
+  (the "sensor"), is parsed to record its media bus configuration, and
+  this info is required in imx-media-csi.c to setup the CSI.
+  Laurent Pinchart argues that instead the CSI subdev should call its
+  neighbor's g_mbus_config op (which should be propagated if necessary)
+  to get this info. However Hans Verkuil is planning to remove the
+  g_mbus_config op. For now this driver uses the parsed DT mbus config
+  method until this issue is resolved.
diff --git a/drivers/staging/media/imx/imx-media-dev.c b/drivers/staging/media/imx/imx-media-dev.c
new file mode 100644
index 0000000..5213210
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media-dev.c
@@ -0,0 +1,522 @@
+/*
+ * V4L2 Media Controller Driver for Freescale i.MX5/6 SOC
+ *
+ * Copyright (c) 2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/delay.h>
+#include <linux/fs.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/platform_device.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/timer.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-ioctl.h>
+#include <media/v4l2-mc.h>
+#include <video/imx-ipu-v3.h>
+#include <media/imx.h>
+#include "imx-media.h"
+
+static inline struct imx_media_dev *notifier2dev(struct v4l2_async_notifier *n)
+{
+	return container_of(n, struct imx_media_dev, subdev_notifier);
+}
+
+/*
+ * Find a subdev by device node or device name. This is called during
+ * driver load to form the async subdev list and bind them.
+ */
+struct imx_media_subdev *
+imx_media_find_async_subdev(struct imx_media_dev *imxmd,
+			    struct device_node *np,
+			    const char *devname)
+{
+	struct imx_media_subdev *imxsd;
+	int i;
+
+	for (i = 0; i < imxmd->subdev_notifier.num_subdevs; i++) {
+		imxsd = &imxmd->subdev[i];
+		switch (imxsd->asd.match_type) {
+		case V4L2_ASYNC_MATCH_OF:
+			if (np && imxsd->asd.match.of.node == np)
+				return imxsd;
+			break;
+		case V4L2_ASYNC_MATCH_DEVNAME:
+			if (devname &&
+			    !strcmp(imxsd->asd.match.device_name.name, devname))
+				return imxsd;
+			break;
+		default:
+			break;
+		}
+	}
+
+	return NULL;
+}
+
+/*
+ * Adds a subdev to the async subdev list. If np is non-NULL, adds
+ * the async as a V4L2_ASYNC_MATCH_OF match type, otherwise as a
+ * V4L2_ASYNC_MATCH_DEVNAME match type using the dev_name of the
+ * given platform_device. This is called during driver load when
+ * forming the async subdev list.
+ */
+struct imx_media_subdev *
+imx_media_add_async_subdev(struct imx_media_dev *imxmd,
+			   struct device_node *np,
+			   struct platform_device *pdev)
+{
+	struct imx_media_subdev *imxsd;
+	struct v4l2_async_subdev *asd;
+	const char *devname = NULL;
+	int sd_idx;
+
+	if (pdev)
+		devname = dev_name(&pdev->dev);
+
+	/* return NULL if this subdev already added */
+	if (imx_media_find_async_subdev(imxmd, np, devname)) {
+		dev_dbg(imxmd->md.dev, "%s: already added %s\n",
+			__func__, np ? np->name : devname);
+		return NULL;
+	}
+
+	sd_idx = imxmd->subdev_notifier.num_subdevs;
+	if (sd_idx >= IMX_MEDIA_MAX_SUBDEVS) {
+		dev_err(imxmd->md.dev, "%s: too many subdevs! can't add %s\n",
+			__func__, np ? np->name : devname);
+		return ERR_PTR(-ENOSPC);
+	}
+
+	imxsd = &imxmd->subdev[sd_idx];
+
+	asd = &imxsd->asd;
+	if (np) {
+		asd->match_type = V4L2_ASYNC_MATCH_OF;
+		asd->match.of.node = np;
+	} else {
+		asd->match_type = V4L2_ASYNC_MATCH_DEVNAME;
+		strncpy(imxsd->devname, devname, sizeof(imxsd->devname));
+		asd->match.device_name.name = imxsd->devname;
+		imxsd->pdev = pdev;
+	}
+
+	imxmd->async_ptrs[sd_idx] = asd;
+	imxmd->subdev_notifier.num_subdevs++;
+
+	dev_dbg(imxmd->md.dev, "%s: added %s, match type %s\n",
+		__func__, np ? np->name : devname, np ? "OF" : "DEVNAME");
+
+	return imxsd;
+}
+
+/*
+ * Adds an imx-media link to a subdev pad's link list. This is called
+ * during driver load when forming the links between subdevs.
+ *
+ * @pad: the local pad
+ * @remote_node: the device node of the remote subdev
+ * @remote_devname: the device name of the remote subdev
+ * @local_pad: local pad index
+ * @remote_pad: remote pad index
+ */
+int imx_media_add_pad_link(struct imx_media_dev *imxmd,
+			   struct imx_media_pad *pad,
+			   struct device_node *remote_node,
+			   const char *remote_devname,
+			   int local_pad, int remote_pad)
+{
+	struct imx_media_link *link;
+	int link_idx;
+
+	link_idx = pad->num_links;
+	if (link_idx >= IMX_MEDIA_MAX_LINKS) {
+		dev_err(imxmd->md.dev, "%s: too many links!\n", __func__);
+		return -ENOSPC;
+	}
+
+	link = &pad->link[link_idx];
+
+	link->remote_sd_node = remote_node;
+	if (remote_devname)
+		strncpy(link->remote_devname, remote_devname,
+			sizeof(link->remote_devname));
+
+	link->local_pad = local_pad;
+	link->remote_pad = remote_pad;
+
+	pad->num_links++;
+
+	return 0;
+}
+
+/*
+ * get IPU from this CSI and add it to the list of IPUs
+ * the media driver will control.
+ */
+static int imx_media_get_ipu(struct imx_media_dev *imxmd,
+			     struct v4l2_subdev *csi_sd)
+{
+	struct ipu_soc *ipu;
+	int ipu_id;
+
+	ipu = dev_get_drvdata(csi_sd->dev->parent);
+	if (!ipu) {
+		v4l2_err(&imxmd->v4l2_dev,
+			 "CSI %s has no parent IPU!\n", csi_sd->name);
+		return -ENODEV;
+	}
+
+	ipu_id = ipu_get_num(ipu);
+	if (ipu_id > 1) {
+		v4l2_err(&imxmd->v4l2_dev, "invalid IPU id %d!\n", ipu_id);
+		return -ENODEV;
+	}
+
+	if (!imxmd->ipu[ipu_id])
+		imxmd->ipu[ipu_id] = ipu;
+
+	return 0;
+}
+
+/* async subdev bound notifier */
+static int imx_media_subdev_bound(struct v4l2_async_notifier *notifier,
+				  struct v4l2_subdev *sd,
+				  struct v4l2_async_subdev *asd)
+{
+	struct imx_media_dev *imxmd = notifier2dev(notifier);
+	struct imx_media_subdev *imxsd;
+	int ret = -EINVAL;
+
+	imxsd = imx_media_find_async_subdev(imxmd, sd->of_node,
+					    dev_name(sd->dev));
+	if (!imxsd)
+		goto out;
+
+	if (sd->grp_id & IMX_MEDIA_GRP_ID_CSI) {
+		ret = imx_media_get_ipu(imxmd, sd);
+		if (ret)
+			return ret;
+	} else if (sd->entity.function == MEDIA_ENT_F_VID_MUX) {
+		/* this is a video mux */
+		sd->grp_id = IMX_MEDIA_GRP_ID_VIDMUX;
+	} else if (imxsd->num_sink_pads == 0) {
+		/*
+		 * this is an original source of video frames, it
+		 * could be a camera sensor, an analog decoder, or
+		 * a bridge device (HDMI -> MIPI CSI-2 for example).
+		 * This group ID is used to locate the entity that
+		 * is the original source of video in a pipeline.
+		 */
+		sd->grp_id = IMX_MEDIA_GRP_ID_SENSOR;
+	}
+
+	/* attach the subdev */
+	imxsd->sd = sd;
+
+	ret = 0;
+out:
+	if (ret)
+		v4l2_warn(&imxmd->v4l2_dev,
+			  "Received unknown subdev %s\n", sd->name);
+	else
+		v4l2_info(&imxmd->v4l2_dev,
+			  "Registered subdev %s\n", sd->name);
+
+	return ret;
+}
+
+/*
+ * create a single media link given a local subdev, a single pad from that
+ * subdev, and a single link from that pad. Called after all subdevs have
+ * registered.
+ */
+static int imx_media_create_link(struct imx_media_dev *imxmd,
+				 struct imx_media_subdev *local_sd,
+				 struct imx_media_pad *pad,
+				 struct imx_media_link *link)
+{
+	struct imx_media_subdev *remote_sd;
+	struct v4l2_subdev *source, *sink;
+	u16 source_pad, sink_pad;
+	int ret;
+
+	/* only create the source->sink links */
+	if (pad->pad.flags & MEDIA_PAD_FL_SINK)
+		return 0;
+
+	remote_sd = imx_media_find_async_subdev(imxmd, link->remote_sd_node,
+						link->remote_devname);
+	if (!remote_sd) {
+		v4l2_warn(&imxmd->v4l2_dev, "%s: no remote for %s:%d\n",
+			  __func__, local_sd->sd->name, link->local_pad);
+		return 0;
+	}
+
+	source = local_sd->sd;
+	sink = remote_sd->sd;
+	source_pad = link->local_pad;
+	sink_pad = link->remote_pad;
+
+	v4l2_info(&imxmd->v4l2_dev, "%s: %s:%d -> %s:%d\n", __func__,
+		  source->name, source_pad, sink->name, sink_pad);
+
+	ret = media_create_pad_link(&source->entity, source_pad,
+				    &sink->entity, sink_pad, 0);
+	if (ret)
+		v4l2_err(&imxmd->v4l2_dev,
+			 "create_pad_link failed: %d\n", ret);
+
+	return ret;
+}
+
+/*
+ * create the media links from all imx-media pads and their links.
+ * Called after all subdevs have registered.
+ */
+static int imx_media_create_links(struct imx_media_dev *imxmd)
+{
+	struct imx_media_subdev *local_sd;
+	struct imx_media_link *link;
+	struct imx_media_pad *pad;
+	int num_pads, i, j, k;
+	int ret = 0;
+
+	for (i = 0; i < imxmd->num_subdevs; i++) {
+		local_sd = &imxmd->subdev[i];
+		num_pads = local_sd->num_sink_pads + local_sd->num_src_pads;
+
+		for (j = 0; j < num_pads; j++) {
+			pad = &local_sd->pad[j];
+
+			for (k = 0; k < pad->num_links; k++) {
+				link = &pad->link[k];
+
+				ret = imx_media_create_link(imxmd, local_sd,
+							    pad, link);
+				if (ret)
+					goto out;
+			}
+		}
+	}
+
+out:
+	return ret;
+}
+
+/* async subdev complete notifier */
+static int imx_media_probe_complete(struct v4l2_async_notifier *notifier)
+{
+	struct imx_media_dev *imxmd = notifier2dev(notifier);
+	int i, ret;
+
+	mutex_lock(&imxmd->md.graph_mutex);
+
+	/* make sure all subdevs were bound */
+	for (i = 0; i < imxmd->num_subdevs; i++) {
+		if (!imxmd->subdev[i].sd) {
+			v4l2_err(&imxmd->v4l2_dev, "unbound subdev!\n");
+			ret = -ENODEV;
+			goto unlock;
+		}
+	}
+
+	ret = imx_media_create_links(imxmd);
+	if (ret)
+		goto unlock;
+
+	ret = v4l2_device_register_subdev_nodes(&imxmd->v4l2_dev);
+unlock:
+	mutex_unlock(&imxmd->md.graph_mutex);
+	if (ret)
+		return ret;
+
+	return media_device_register(&imxmd->md);
+}
+
+static int imx_media_link_notify(struct media_link *link, u32 flags,
+				 unsigned int notification)
+{
+	struct media_entity *source = link->source->entity;
+	struct media_entity *sink = link->sink->entity;
+	struct imx_media_dev *imxmd;
+	struct media_graph *graph;
+	struct video_device *vdev;
+	struct v4l2_subdev *sd;
+	int ret = 0;
+
+	if (is_media_entity_v4l2_subdev(sink))
+		sd = media_entity_to_v4l2_subdev(sink);
+	else
+		sd = media_entity_to_v4l2_subdev(source);
+
+	imxmd = dev_get_drvdata(sd->v4l2_dev->dev);
+	graph = &imxmd->link_notify_graph;
+
+	vdev = imx_media_find_pipeline_video_device(imxmd, sink);
+	if (!IS_ERR(vdev)) {
+		/*
+		 * reset video device controls on any change to
+		 * the pipeline.
+		 */
+		v4l2_ctrl_handler_free(vdev->ctrl_handler);
+		v4l2_ctrl_handler_init(vdev->ctrl_handler, 0);
+	} else {
+		vdev = NULL;
+	}
+
+	if (notification == MEDIA_DEV_NOTIFY_PRE_LINK_CH) {
+		ret = media_graph_walk_init(graph, &imxmd->md);
+		if (ret)
+			return ret;
+
+		if (flags & MEDIA_LNK_FL_ENABLED)
+			return 0;
+
+		/* Before link disconnection */
+		return imx_media_pipeline_set_power(imxmd, graph, sink, false);
+	}
+
+	/* MEDIA_DEV_NOTIFY_POST_LINK_CH */
+
+	if (!(link->flags & MEDIA_LNK_FL_ENABLED))
+		goto cleanup;
+
+	/* After link activation */
+	ret = imx_media_pipeline_set_power(imxmd, graph, sink, true);
+	if (ret)
+		goto cleanup;
+
+	if (vdev)
+		ret = __v4l2_pipeline_inherit_controls(vdev, sink);
+cleanup:
+	media_graph_walk_cleanup(graph);
+	return ret ? -EPIPE : 0;
+}
+
+static const struct media_device_ops imx_media_md_ops = {
+	.link_notify = imx_media_link_notify,
+};
+
+static int imx_media_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *node = dev->of_node;
+	struct imx_media_subdev *csi[4] = {0};
+	struct imx_media_dev *imxmd;
+	int ret;
+
+	imxmd = devm_kzalloc(dev, sizeof(*imxmd), GFP_KERNEL);
+	if (!imxmd)
+		return -ENOMEM;
+
+	dev_set_drvdata(dev, imxmd);
+
+	strlcpy(imxmd->md.model, "imx-media", sizeof(imxmd->md.model));
+	imxmd->md.ops = &imx_media_md_ops;
+	imxmd->md.dev = dev;
+
+	imxmd->v4l2_dev.mdev = &imxmd->md;
+	strlcpy(imxmd->v4l2_dev.name, "imx-media",
+		sizeof(imxmd->v4l2_dev.name));
+
+	media_device_init(&imxmd->md);
+
+	ret = v4l2_device_register(dev, &imxmd->v4l2_dev);
+	if (ret < 0) {
+		v4l2_err(&imxmd->v4l2_dev,
+			 "Failed to register v4l2_device: %d\n", ret);
+		goto cleanup;
+	}
+
+	dev_set_drvdata(imxmd->v4l2_dev.dev, imxmd);
+
+	ret = imx_media_of_parse(imxmd, &csi, node);
+	if (ret) {
+		v4l2_err(&imxmd->v4l2_dev,
+			 "imx_media_of_parse failed with %d\n", ret);
+		goto unreg_dev;
+	}
+
+	ret = imx_media_add_internal_subdevs(imxmd, csi);
+	if (ret) {
+		v4l2_err(&imxmd->v4l2_dev,
+			 "add_internal_subdevs failed with %d\n", ret);
+		goto unreg_dev;
+	}
+
+	/* no subdevs? just bail */
+	imxmd->num_subdevs = imxmd->subdev_notifier.num_subdevs;
+	if (imxmd->num_subdevs == 0) {
+		ret = -ENODEV;
+		goto unreg_dev;
+	}
+
+	/* prepare the async subdev notifier and register it */
+	imxmd->subdev_notifier.subdevs = imxmd->async_ptrs;
+	imxmd->subdev_notifier.bound = imx_media_subdev_bound;
+	imxmd->subdev_notifier.complete = imx_media_probe_complete;
+	ret = v4l2_async_notifier_register(&imxmd->v4l2_dev,
+					   &imxmd->subdev_notifier);
+	if (ret) {
+		v4l2_err(&imxmd->v4l2_dev,
+			 "v4l2_async_notifier_register failed with %d\n", ret);
+		goto del_int;
+	}
+
+	return 0;
+
+del_int:
+	imx_media_remove_internal_subdevs(imxmd);
+unreg_dev:
+	v4l2_device_unregister(&imxmd->v4l2_dev);
+cleanup:
+	media_device_cleanup(&imxmd->md);
+	return ret;
+}
+
+static int imx_media_remove(struct platform_device *pdev)
+{
+	struct imx_media_dev *imxmd =
+		(struct imx_media_dev *)platform_get_drvdata(pdev);
+
+	v4l2_info(&imxmd->v4l2_dev, "Removing imx-media\n");
+
+	v4l2_async_notifier_unregister(&imxmd->subdev_notifier);
+	imx_media_remove_internal_subdevs(imxmd);
+	v4l2_device_unregister(&imxmd->v4l2_dev);
+	media_device_unregister(&imxmd->md);
+	media_device_cleanup(&imxmd->md);
+
+	return 0;
+}
+
+static const struct of_device_id imx_media_dt_ids[] = {
+	{ .compatible = "fsl,imx-capture-subsystem" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, imx_media_dt_ids);
+
+static struct platform_driver imx_media_pdrv = {
+	.probe		= imx_media_probe,
+	.remove		= imx_media_remove,
+	.driver		= {
+		.name	= "imx-media",
+		.of_match_table	= imx_media_dt_ids,
+	},
+};
+
+module_platform_driver(imx_media_pdrv);
+
+MODULE_DESCRIPTION("i.MX5/6 v4l2 media controller driver");
+MODULE_AUTHOR("Steve Longerbeam <steve_longerbeam@mentor.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/staging/media/imx/imx-media-fim.c b/drivers/staging/media/imx/imx-media-fim.c
new file mode 100644
index 0000000..824d257
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media-fim.c
@@ -0,0 +1,471 @@
+/*
+ * Frame Interval Monitor.
+ *
+ * Copyright (c) 2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-of.h>
+#include <media/v4l2-subdev.h>
+#include <media/imx.h>
+#include "imx-media.h"
+
+enum {
+	FIM_CL_ENABLE = 0,
+	FIM_CL_NUM,
+	FIM_CL_TOLERANCE_MIN,
+	FIM_CL_TOLERANCE_MAX,
+	FIM_CL_NUM_SKIP,
+	FIM_NUM_CONTROLS,
+};
+
+#define FIM_CL_ENABLE_DEF          1 /* FIM enabled by default */
+#define FIM_CL_NUM_DEF             8 /* average 8 frames */
+#define FIM_CL_NUM_SKIP_DEF        2 /* skip 2 frames after restart */
+#define FIM_CL_TOLERANCE_MIN_DEF  50 /* usec */
+#define FIM_CL_TOLERANCE_MAX_DEF   0 /* no max tolerance (unbounded) */
+
+struct imx_media_fim {
+	struct imx_media_dev *md;
+
+	/* the owning subdev of this fim instance */
+	struct v4l2_subdev *sd;
+
+	/* FIM's control handler */
+	struct v4l2_ctrl_handler ctrl_handler;
+
+	/* control cluster */
+	struct v4l2_ctrl  *ctrl[FIM_NUM_CONTROLS];
+
+	/* current control values */
+	bool              enabled;
+	int               num_avg;
+	int               num_skip;
+	unsigned long     tolerance_min; /* usec */
+	unsigned long     tolerance_max; /* usec */
+
+	int               counter;
+	struct timespec   last_ts;
+	unsigned long     sum;       /* usec */
+	unsigned long     nominal;   /* usec */
+
+	/*
+	 * input capture method of measuring FI (channel and flags
+	 * from device tree)
+	 */
+	int               icap_channel;
+	int               icap_flags;
+	struct completion icap_first_event;
+};
+
+static void update_fim_nominal(struct imx_media_fim *fim,
+			       struct imx_media_subdev *sensor)
+{
+	struct v4l2_streamparm parm;
+	struct v4l2_fract tpf;
+	int ret;
+
+	parm.type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
+	ret = v4l2_subdev_call(sensor->sd, video, g_parm, &parm);
+	tpf = parm.parm.capture.timeperframe;
+
+	if (ret || tpf.denominator == 0) {
+		dev_dbg(fim->sd->dev, "no tpf from sensor, FIM disabled\n");
+		fim->enabled = false;
+		return;
+	}
+
+	fim->nominal = DIV_ROUND_CLOSEST(1000 * 1000 * tpf.numerator,
+					 tpf.denominator);
+
+	dev_dbg(fim->sd->dev, "sensor FI=%lu usec\n", fim->nominal);
+}
+
+static void reset_fim(struct imx_media_fim *fim, bool curval)
+{
+	struct v4l2_ctrl *en = fim->ctrl[FIM_CL_ENABLE];
+	struct v4l2_ctrl *num = fim->ctrl[FIM_CL_NUM];
+	struct v4l2_ctrl *skip = fim->ctrl[FIM_CL_NUM_SKIP];
+	struct v4l2_ctrl *tol_min = fim->ctrl[FIM_CL_TOLERANCE_MIN];
+	struct v4l2_ctrl *tol_max = fim->ctrl[FIM_CL_TOLERANCE_MAX];
+
+	if (curval) {
+		fim->enabled = en->cur.val;
+		fim->num_avg = num->cur.val;
+		fim->num_skip = skip->cur.val;
+		fim->tolerance_min = tol_min->cur.val;
+		fim->tolerance_max = tol_max->cur.val;
+	} else {
+		fim->enabled = en->val;
+		fim->num_avg = num->val;
+		fim->num_skip = skip->val;
+		fim->tolerance_min = tol_min->val;
+		fim->tolerance_max = tol_max->val;
+	}
+
+	/* disable tolerance range if max <= min */
+	if (fim->tolerance_max <= fim->tolerance_min)
+		fim->tolerance_max = 0;
+
+	fim->counter = -fim->num_skip;
+	fim->sum = 0;
+}
+
+static void send_fim_event(struct imx_media_fim *fim, unsigned long error)
+{
+	static const struct v4l2_event ev = {
+		.type = V4L2_EVENT_FRAME_INTERVAL_ERROR,
+	};
+
+	v4l2_subdev_notify_event(fim->sd, &ev);
+}
+
+/*
+ * Monitor an averaged frame interval. If the average deviates too much
+ * from the sensor's nominal frame rate, send the frame interval error
+ * event. The frame intervals are averaged in order to quiet noise from
+ * (presumably random) interrupt latency.
+ */
+static void frame_interval_monitor(struct imx_media_fim *fim,
+				   struct timespec *ts)
+{
+	unsigned long interval, error, error_avg;
+	struct timespec diff;
+	bool send_event = false;
+
+	if (!fim->enabled || ++fim->counter <= 0)
+		goto out_update_ts;
+
+	diff = timespec_sub(*ts, fim->last_ts);
+	interval = diff.tv_sec * 1000 * 1000 + diff.tv_nsec / 1000;
+	error = abs(interval - fim->nominal);
+
+	if (fim->tolerance_max && error >= fim->tolerance_max) {
+		dev_dbg(fim->sd->dev,
+			"FIM: %lu ignored, out of tolerance bounds\n",
+			error);
+		fim->counter--;
+		goto out_update_ts;
+	}
+
+	fim->sum += error;
+
+	if (fim->counter == fim->num_avg) {
+		error_avg = DIV_ROUND_CLOSEST(fim->sum, fim->num_avg);
+
+		if (error_avg > fim->tolerance_min)
+			send_event = true;
+
+		dev_dbg(fim->sd->dev, "FIM: error: %lu usec%s\n",
+			error_avg, send_event ? " (!!!)" : "");
+
+		fim->counter = 0;
+		fim->sum = 0;
+	}
+
+out_update_ts:
+	fim->last_ts = *ts;
+	if (send_event)
+		send_fim_event(fim, error_avg);
+}
+
+#ifdef CONFIG_IMX_GPT_ICAP
+/*
+ * Input Capture method of measuring frame intervals. Not subject
+ * to interrupt latency.
+ */
+static void fim_input_capture_handler(int channel, void *dev_id,
+				      struct timespec *ts)
+{
+	struct imx_media_fim *fim = dev_id;
+
+	frame_interval_monitor(fim, ts);
+
+	if (!completion_done(&fim->icap_first_event))
+		complete(&fim->icap_first_event);
+}
+
+static int fim_request_input_capture(struct imx_media_fim *fim)
+{
+	init_completion(&fim->icap_first_event);
+
+	return mxc_request_input_capture(fim->icap_channel,
+					 fim_input_capture_handler,
+					 fim->icap_flags, fim);
+}
+
+static void fim_free_input_capture(struct imx_media_fim *fim)
+{
+	mxc_free_input_capture(fim->icap_channel, fim);
+}
+
+#else /* CONFIG_IMX_GPT_ICAP */
+
+static int fim_request_input_capture(struct imx_media_fim *fim)
+{
+	return 0;
+}
+
+static void fim_free_input_capture(struct imx_media_fim *fim)
+{
+}
+
+#endif /* CONFIG_IMX_GPT_ICAP */
+
+/*
+ * In case we are monitoring the first frame interval after streamon
+ * (when fim->num_skip = 0), we need a valid fim->last_ts before we
+ * can begin. This only applies to the input capture method. It is not
+ * possible to accurately measure the first FI after streamon using the
+ * EOF method, so fim->num_skip minimum is set to 1 in that case, so this
+ * function is a noop when the EOF method is used.
+ */
+static void fim_acquire_first_ts(struct imx_media_fim *fim)
+{
+	unsigned long ret;
+
+	if (!fim->enabled || fim->num_skip > 0)
+		return;
+
+	ret = wait_for_completion_timeout(
+		&fim->icap_first_event,
+		msecs_to_jiffies(IMX_MEDIA_EOF_TIMEOUT));
+	if (ret == 0)
+		v4l2_warn(fim->sd, "wait first icap event timeout\n");
+}
+
+/* FIM Controls */
+static int fim_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct imx_media_fim *fim = container_of(ctrl->handler,
+						 struct imx_media_fim,
+						 ctrl_handler);
+
+	switch (ctrl->id) {
+	case V4L2_CID_IMX_FIM_ENABLE:
+		reset_fim(fim, false);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static const struct v4l2_ctrl_ops fim_ctrl_ops = {
+	.s_ctrl = fim_s_ctrl,
+};
+
+static const struct v4l2_ctrl_config imx_media_fim_ctrl[] = {
+	[FIM_CL_ENABLE] = {
+		.ops = &fim_ctrl_ops,
+		.id = V4L2_CID_IMX_FIM_ENABLE,
+		.name = "FIM Enable",
+		.type = V4L2_CTRL_TYPE_BOOLEAN,
+		.def = FIM_CL_ENABLE_DEF,
+		.min = 0,
+		.max = 1,
+		.step = 1,
+	},
+	[FIM_CL_NUM] = {
+		.ops = &fim_ctrl_ops,
+		.id = V4L2_CID_IMX_FIM_NUM,
+		.name = "FIM Num Average",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.def = FIM_CL_NUM_DEF,
+		.min =  1, /* no averaging */
+		.max = 64, /* average 64 frames */
+		.step = 1,
+	},
+	[FIM_CL_TOLERANCE_MIN] = {
+		.ops = &fim_ctrl_ops,
+		.id = V4L2_CID_IMX_FIM_TOLERANCE_MIN,
+		.name = "FIM Tolerance Min",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.def = FIM_CL_TOLERANCE_MIN_DEF,
+		.min =    2,
+		.max =  200,
+		.step =   1,
+	},
+	[FIM_CL_TOLERANCE_MAX] = {
+		.ops = &fim_ctrl_ops,
+		.id = V4L2_CID_IMX_FIM_TOLERANCE_MAX,
+		.name = "FIM Tolerance Max",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.def = FIM_CL_TOLERANCE_MAX_DEF,
+		.min =    0,
+		.max =  500,
+		.step =   1,
+	},
+	[FIM_CL_NUM_SKIP] = {
+		.ops = &fim_ctrl_ops,
+		.id = V4L2_CID_IMX_FIM_NUM_SKIP,
+		.name = "FIM Num Skip",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.def = FIM_CL_NUM_SKIP_DEF,
+		.min =   0, /* skip no frames */
+		.max = 256, /* skip 256 frames */
+		.step =  1,
+	},
+};
+
+static int init_fim_controls(struct imx_media_fim *fim)
+{
+	struct v4l2_ctrl_handler *hdlr = &fim->ctrl_handler;
+	struct v4l2_ctrl_config fim_c;
+	int i, ret;
+
+	v4l2_ctrl_handler_init(hdlr, FIM_NUM_CONTROLS);
+
+	for (i = 0; i < FIM_NUM_CONTROLS; i++) {
+		fim_c = imx_media_fim_ctrl[i];
+
+		/*
+		 * it's not possible to accurately measure the first
+		 * FI after streamon using the EOF method, so force
+		 * num_skip minimum to 1 in that case.
+		 */
+		if (i == FIM_CL_NUM_SKIP && fim->icap_channel < 0)
+			fim_c.min = 1;
+
+		fim->ctrl[i] = v4l2_ctrl_new_custom(hdlr, &fim_c, NULL);
+	}
+
+	if (hdlr->error) {
+		ret = hdlr->error;
+		goto err_free;
+	}
+
+	v4l2_ctrl_cluster(FIM_NUM_CONTROLS, fim->ctrl);
+
+	/* add the FIM controls to the calling subdev ctrl handler */
+	ret = v4l2_ctrl_add_handler(fim->sd->ctrl_handler,
+				    &fim->ctrl_handler, NULL);
+	if (ret)
+		goto err_free;
+
+	return 0;
+err_free:
+	v4l2_ctrl_handler_free(hdlr);
+	return ret;
+}
+
+static int of_parse_fim(struct imx_media_fim *fim, struct device_node *np)
+{
+	struct device_node *fim_np;
+	u32 icap[2];
+	int ret;
+
+	/* by default EOF method is used */
+	fim->icap_channel = -1;
+
+	fim_np = of_get_child_by_name(np, "fim");
+	if (!fim_np || !of_device_is_available(fim_np)) {
+		of_node_put(fim_np);
+		return -ENODEV;
+	}
+
+	if (IS_ENABLED(CONFIG_IMX_GPT_ICAP)) {
+		ret = of_property_read_u32_array(fim_np,
+						 "fsl,input-capture-channel",
+						 icap, 2);
+		if (!ret) {
+			fim->icap_channel = icap[0];
+			fim->icap_flags = icap[1];
+		}
+	}
+
+	of_node_put(fim_np);
+	return 0;
+}
+
+/*
+ * Monitor frame intervals via EOF interrupt. This method is
+ * subject to uncertainty errors introduced by interrupt latency.
+ *
+ * This is a noop if the Input Capture method is being used, since
+ * the frame_interval_monitor() is called by the input capture event
+ * callback handler in that case.
+ */
+void imx_media_fim_eof_monitor(struct imx_media_fim *fim, struct timespec *ts)
+{
+	if (fim->icap_channel >= 0)
+		return;
+
+	frame_interval_monitor(fim, ts);
+}
+EXPORT_SYMBOL_GPL(imx_media_fim_eof_monitor);
+
+/* Called by the subdev in its s_power callback */
+int imx_media_fim_set_power(struct imx_media_fim *fim, bool on)
+{
+	int ret = 0;
+
+	if (fim->icap_channel >= 0) {
+		if (on)
+			ret = fim_request_input_capture(fim);
+		else
+			fim_free_input_capture(fim);
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(imx_media_fim_set_power);
+
+/* Called by the subdev in its s_stream callback */
+int imx_media_fim_set_stream(struct imx_media_fim *fim,
+			     struct imx_media_subdev *sensor,
+			     bool on)
+{
+	if (on) {
+		reset_fim(fim, true);
+		update_fim_nominal(fim, sensor);
+
+		if (fim->icap_channel >= 0)
+			fim_acquire_first_ts(fim);
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_fim_set_stream);
+
+/* Called by the subdev in its subdev registered callback */
+struct imx_media_fim *imx_media_fim_init(struct v4l2_subdev *sd)
+{
+	struct device_node *node = sd->of_node;
+	struct imx_media_fim *fim;
+	int ret;
+
+	fim = devm_kzalloc(sd->dev, sizeof(*fim), GFP_KERNEL);
+	if (!fim)
+		return ERR_PTR(-ENOMEM);
+
+	/* get media device */
+	fim->md = dev_get_drvdata(sd->v4l2_dev->dev);
+	fim->sd = sd;
+
+	ret = of_parse_fim(fim, node);
+	if (ret)
+		return (ret == -ENODEV) ? NULL : ERR_PTR(ret);
+
+	ret = init_fim_controls(fim);
+	if (ret)
+		return ERR_PTR(ret);
+
+	return fim;
+}
+EXPORT_SYMBOL_GPL(imx_media_fim_init);
+
+void imx_media_fim_free(struct imx_media_fim *fim)
+{
+	v4l2_ctrl_handler_free(&fim->ctrl_handler);
+}
+EXPORT_SYMBOL_GPL(imx_media_fim_free);
diff --git a/drivers/staging/media/imx/imx-media-internal-sd.c b/drivers/staging/media/imx/imx-media-internal-sd.c
new file mode 100644
index 0000000..cdfbf40
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media-internal-sd.c
@@ -0,0 +1,349 @@
+/*
+ * Media driver for Freescale i.MX5/6 SOC
+ *
+ * Adds the internal subdevices and the media links between them.
+ *
+ * Copyright (c) 2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/platform_device.h>
+#include "imx-media.h"
+
+enum isd_enum {
+	isd_csi0 = 0,
+	isd_csi1,
+	isd_vdic,
+	isd_ic_prp,
+	isd_ic_prpenc,
+	isd_ic_prpvf,
+	num_isd,
+};
+
+static const struct internal_subdev_id {
+	enum isd_enum index;
+	const char *name;
+	u32 grp_id;
+} isd_id[num_isd] = {
+	[isd_csi0] = {
+		.index = isd_csi0,
+		.grp_id = IMX_MEDIA_GRP_ID_CSI0,
+		.name = "imx-ipuv3-csi",
+	},
+	[isd_csi1] = {
+		.index = isd_csi1,
+		.grp_id = IMX_MEDIA_GRP_ID_CSI1,
+		.name = "imx-ipuv3-csi",
+	},
+	[isd_vdic] = {
+		.index = isd_vdic,
+		.grp_id = IMX_MEDIA_GRP_ID_VDIC,
+		.name = "imx-ipuv3-vdic",
+	},
+	[isd_ic_prp] = {
+		.index = isd_ic_prp,
+		.grp_id = IMX_MEDIA_GRP_ID_IC_PRP,
+		.name = "imx-ipuv3-ic",
+	},
+	[isd_ic_prpenc] = {
+		.index = isd_ic_prpenc,
+		.grp_id = IMX_MEDIA_GRP_ID_IC_PRPENC,
+		.name = "imx-ipuv3-ic",
+	},
+	[isd_ic_prpvf] = {
+		.index = isd_ic_prpvf,
+		.grp_id = IMX_MEDIA_GRP_ID_IC_PRPVF,
+		.name = "imx-ipuv3-ic",
+	},
+};
+
+struct internal_link {
+	const struct internal_subdev_id *remote_id;
+	int remote_pad;
+};
+
+struct internal_pad {
+	bool devnode; /* does this pad link to a device node */
+	struct internal_link link[IMX_MEDIA_MAX_LINKS];
+};
+
+static const struct internal_subdev {
+	const struct internal_subdev_id *id;
+	struct internal_pad pad[IMX_MEDIA_MAX_PADS];
+	int num_sink_pads;
+	int num_src_pads;
+} internal_subdev[num_isd] = {
+	[isd_csi0] = {
+		.id = &isd_id[isd_csi0],
+		.num_sink_pads = CSI_NUM_SINK_PADS,
+		.num_src_pads = CSI_NUM_SRC_PADS,
+		.pad[CSI_SRC_PAD_DIRECT] = {
+			.link = {
+				{
+					.remote_id = &isd_id[isd_ic_prp],
+					.remote_pad = PRP_SINK_PAD,
+				}, {
+					.remote_id =  &isd_id[isd_vdic],
+					.remote_pad = VDIC_SINK_PAD_DIRECT,
+				},
+			},
+		},
+		.pad[CSI_SRC_PAD_IDMAC] = {
+			.devnode = true,
+		},
+	},
+
+	[isd_csi1] = {
+		.id = &isd_id[isd_csi1],
+		.num_sink_pads = CSI_NUM_SINK_PADS,
+		.num_src_pads = CSI_NUM_SRC_PADS,
+		.pad[CSI_SRC_PAD_DIRECT] = {
+			.link = {
+				{
+					.remote_id = &isd_id[isd_ic_prp],
+					.remote_pad = PRP_SINK_PAD,
+				}, {
+					.remote_id =  &isd_id[isd_vdic],
+					.remote_pad = VDIC_SINK_PAD_DIRECT,
+				},
+			},
+		},
+		.pad[CSI_SRC_PAD_IDMAC] = {
+			.devnode = true,
+		},
+	},
+
+	[isd_vdic] = {
+		.id = &isd_id[isd_vdic],
+		.num_sink_pads = VDIC_NUM_SINK_PADS,
+		.num_src_pads = VDIC_NUM_SRC_PADS,
+		.pad[VDIC_SINK_PAD_IDMAC] = {
+			.devnode = true,
+		},
+		.pad[VDIC_SRC_PAD_DIRECT] = {
+			.link = {
+				{
+					.remote_id =  &isd_id[isd_ic_prp],
+					.remote_pad = PRP_SINK_PAD,
+				},
+			},
+		},
+	},
+
+	[isd_ic_prp] = {
+		.id = &isd_id[isd_ic_prp],
+		.num_sink_pads = PRP_NUM_SINK_PADS,
+		.num_src_pads = PRP_NUM_SRC_PADS,
+		.pad[PRP_SRC_PAD_PRPENC] = {
+			.link = {
+				{
+					.remote_id = &isd_id[isd_ic_prpenc],
+					.remote_pad = 0,
+				},
+			},
+		},
+		.pad[PRP_SRC_PAD_PRPVF] = {
+			.link = {
+				{
+					.remote_id = &isd_id[isd_ic_prpvf],
+					.remote_pad = 0,
+				},
+			},
+		},
+	},
+
+	[isd_ic_prpenc] = {
+		.id = &isd_id[isd_ic_prpenc],
+		.num_sink_pads = PRPENCVF_NUM_SINK_PADS,
+		.num_src_pads = PRPENCVF_NUM_SRC_PADS,
+		.pad[PRPENCVF_SRC_PAD] = {
+			.devnode = true,
+		},
+	},
+
+	[isd_ic_prpvf] = {
+		.id = &isd_id[isd_ic_prpvf],
+		.num_sink_pads = PRPENCVF_NUM_SINK_PADS,
+		.num_src_pads = PRPENCVF_NUM_SRC_PADS,
+		.pad[PRPENCVF_SRC_PAD] = {
+			.devnode = true,
+		},
+	},
+};
+
+/* form a device name given a group id and ipu id */
+static inline void isd_id_to_devname(char *devname, int sz,
+				     const struct internal_subdev_id *id,
+				     int ipu_id)
+{
+	int pdev_id = ipu_id * num_isd + id->index;
+
+	snprintf(devname, sz, "%s.%d", id->name, pdev_id);
+}
+
+/* adds the links from given internal subdev */
+static int add_internal_links(struct imx_media_dev *imxmd,
+			      const struct internal_subdev *isd,
+			      struct imx_media_subdev *imxsd,
+			      int ipu_id)
+{
+	int i, num_pads, ret;
+
+	num_pads = isd->num_sink_pads + isd->num_src_pads;
+
+	for (i = 0; i < num_pads; i++) {
+		const struct internal_pad *intpad = &isd->pad[i];
+		struct imx_media_pad *pad = &imxsd->pad[i];
+		int j;
+
+		/* init the pad flags for this internal subdev */
+		pad->pad.flags = (i < isd->num_sink_pads) ?
+			MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
+		/* export devnode pad flag to the subdevs */
+		pad->devnode = intpad->devnode;
+
+		for (j = 0; ; j++) {
+			const struct internal_link *link;
+			char remote_devname[32];
+
+			link = &intpad->link[j];
+
+			if (!link->remote_id)
+				break;
+
+			isd_id_to_devname(remote_devname,
+					  sizeof(remote_devname),
+					  link->remote_id, ipu_id);
+
+			ret = imx_media_add_pad_link(imxmd, pad,
+						     NULL, remote_devname,
+						     i, link->remote_pad);
+			if (ret)
+				return ret;
+		}
+	}
+
+	return 0;
+}
+
+/* register an internal subdev as a platform device */
+static struct imx_media_subdev *
+add_internal_subdev(struct imx_media_dev *imxmd,
+		    const struct internal_subdev *isd,
+		    int ipu_id)
+{
+	struct imx_media_internal_sd_platformdata pdata;
+	struct platform_device_info pdevinfo = {0};
+	struct imx_media_subdev *imxsd;
+	struct platform_device *pdev;
+
+	pdata.grp_id = isd->id->grp_id;
+
+	/* the id of IPU this subdev will control */
+	pdata.ipu_id = ipu_id;
+
+	/* create subdev name */
+	imx_media_grp_id_to_sd_name(pdata.sd_name, sizeof(pdata.sd_name),
+				    pdata.grp_id, ipu_id);
+
+	pdevinfo.name = isd->id->name;
+	pdevinfo.id = ipu_id * num_isd + isd->id->index;
+	pdevinfo.parent = imxmd->md.dev;
+	pdevinfo.data = &pdata;
+	pdevinfo.size_data = sizeof(pdata);
+	pdevinfo.dma_mask = DMA_BIT_MASK(32);
+
+	pdev = platform_device_register_full(&pdevinfo);
+	if (IS_ERR(pdev))
+		return ERR_CAST(pdev);
+
+	imxsd = imx_media_add_async_subdev(imxmd, NULL, pdev);
+	if (IS_ERR(imxsd))
+		return imxsd;
+
+	imxsd->num_sink_pads = isd->num_sink_pads;
+	imxsd->num_src_pads = isd->num_src_pads;
+
+	return imxsd;
+}
+
+/* adds the internal subdevs in one ipu */
+static int add_ipu_internal_subdevs(struct imx_media_dev *imxmd,
+				    struct imx_media_subdev *csi0,
+				    struct imx_media_subdev *csi1,
+				    int ipu_id)
+{
+	enum isd_enum i;
+	int ret;
+
+	for (i = 0; i < num_isd; i++) {
+		const struct internal_subdev *isd = &internal_subdev[i];
+		struct imx_media_subdev *imxsd;
+
+		/*
+		 * the CSIs are represented in the device-tree, so those
+		 * devices are added already, and are added to the async
+		 * subdev list by of_parse_subdev(), so we are given those
+		 * subdevs as csi0 and csi1.
+		 */
+		switch (isd->id->grp_id) {
+		case IMX_MEDIA_GRP_ID_CSI0:
+			imxsd = csi0;
+			break;
+		case IMX_MEDIA_GRP_ID_CSI1:
+			imxsd = csi1;
+			break;
+		default:
+			imxsd = add_internal_subdev(imxmd, isd, ipu_id);
+			break;
+		}
+
+		if (IS_ERR(imxsd))
+			return PTR_ERR(imxsd);
+
+		/* add the links from this subdev */
+		if (imxsd) {
+			ret = add_internal_links(imxmd, isd, imxsd, ipu_id);
+			if (ret)
+				return ret;
+		}
+	}
+
+	return 0;
+}
+
+int imx_media_add_internal_subdevs(struct imx_media_dev *imxmd,
+				   struct imx_media_subdev *csi[4])
+{
+	int ret;
+
+	ret = add_ipu_internal_subdevs(imxmd, csi[0], csi[1], 0);
+	if (ret)
+		goto remove;
+
+	ret = add_ipu_internal_subdevs(imxmd, csi[2], csi[3], 1);
+	if (ret)
+		goto remove;
+
+	return 0;
+
+remove:
+	imx_media_remove_internal_subdevs(imxmd);
+	return ret;
+}
+
+void imx_media_remove_internal_subdevs(struct imx_media_dev *imxmd)
+{
+	struct imx_media_subdev *imxsd;
+	int i;
+
+	for (i = 0; i < imxmd->subdev_notifier.num_subdevs; i++) {
+		imxsd = &imxmd->subdev[i];
+		if (!imxsd->pdev)
+			continue;
+		platform_device_unregister(imxsd->pdev);
+	}
+}
diff --git a/drivers/staging/media/imx/imx-media-of.c b/drivers/staging/media/imx/imx-media-of.c
new file mode 100644
index 0000000..b383be4
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media-of.c
@@ -0,0 +1,267 @@
+/*
+ * Media driver for Freescale i.MX5/6 SOC
+ *
+ * Open Firmware parsing.
+ *
+ * Copyright (c) 2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/of_platform.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-of.h>
+#include <media/v4l2-subdev.h>
+#include <media/videobuf2-dma-contig.h>
+#include <video/imx-ipu-v3.h>
+#include "imx-media.h"
+
+static int of_add_pad_link(struct imx_media_dev *imxmd,
+			   struct imx_media_pad *pad,
+			   struct device_node *local_sd_node,
+			   struct device_node *remote_sd_node,
+			   int local_pad, int remote_pad)
+{
+	dev_dbg(imxmd->md.dev, "%s: adding %s:%d -> %s:%d\n", __func__,
+		local_sd_node->name, local_pad,
+		remote_sd_node->name, remote_pad);
+
+	return imx_media_add_pad_link(imxmd, pad, remote_sd_node, NULL,
+				      local_pad, remote_pad);
+}
+
+static void of_parse_sensor(struct imx_media_dev *imxmd,
+			    struct imx_media_subdev *sensor,
+			    struct device_node *sensor_np)
+{
+	struct device_node *endpoint;
+
+	endpoint = of_graph_get_next_endpoint(sensor_np, NULL);
+	if (endpoint) {
+		v4l2_of_parse_endpoint(endpoint, &sensor->sensor_ep);
+		of_node_put(endpoint);
+	}
+}
+
+static int of_get_port_count(const struct device_node *np)
+{
+	struct device_node *ports, *child;
+	int num = 0;
+
+	/* check if this node has a ports subnode */
+	ports = of_get_child_by_name(np, "ports");
+	if (ports)
+		np = ports;
+
+	for_each_child_of_node(np, child)
+		if (of_node_cmp(child->name, "port") == 0)
+			num++;
+
+	of_node_put(ports);
+	return num;
+}
+
+/*
+ * find the remote device node and remote port id (remote pad #)
+ * given local endpoint node
+ */
+static void of_get_remote_pad(struct device_node *epnode,
+			      struct device_node **remote_node,
+			      int *remote_pad)
+{
+	struct device_node *rp, *rpp;
+	struct device_node *remote;
+
+	rp = of_graph_get_remote_port(epnode);
+	rpp = of_graph_get_remote_port_parent(epnode);
+
+	if (of_device_is_compatible(rpp, "fsl,imx6q-ipu")) {
+		/* the remote is one of the CSI ports */
+		remote = rp;
+		*remote_pad = 0;
+		of_node_put(rpp);
+	} else {
+		remote = rpp;
+		of_property_read_u32(rp, "reg", remote_pad);
+		of_node_put(rp);
+	}
+
+	if (!remote || !of_device_is_available(remote)) {
+		of_node_put(remote);
+		*remote_node = NULL;
+	} else {
+		*remote_node = remote;
+	}
+}
+
+static struct imx_media_subdev *
+of_parse_subdev(struct imx_media_dev *imxmd, struct device_node *sd_np,
+		bool is_csi_port)
+{
+	struct imx_media_subdev *imxsd;
+	int i, num_pads, ret;
+
+	if (!of_device_is_available(sd_np)) {
+		dev_dbg(imxmd->md.dev, "%s: %s not enabled\n", __func__,
+			sd_np->name);
+		return NULL;
+	}
+
+	/* register this subdev with async notifier */
+	imxsd = imx_media_add_async_subdev(imxmd, sd_np, NULL);
+	if (IS_ERR_OR_NULL(imxsd))
+		return imxsd;
+
+	if (is_csi_port) {
+		/*
+		 * the ipu-csi has one sink port and two source ports.
+		 * The source ports are not represented in the device tree,
+		 * but are described by the internal pads and links later.
+		 */
+		num_pads = CSI_NUM_PADS;
+		imxsd->num_sink_pads = CSI_NUM_SINK_PADS;
+	} else if (of_device_is_compatible(sd_np, "fsl,imx6-mipi-csi2")) {
+		num_pads = of_get_port_count(sd_np);
+		/* the mipi csi2 receiver has only one sink port */
+		imxsd->num_sink_pads = 1;
+	} else if (of_device_is_compatible(sd_np, "video-multiplexer")) {
+		num_pads = of_get_port_count(sd_np);
+		/* for the video mux, all but the last port are sinks */
+		imxsd->num_sink_pads = num_pads - 1;
+	} else {
+		num_pads = of_get_port_count(sd_np);
+		if (num_pads != 1) {
+			dev_warn(imxmd->md.dev,
+				 "%s: unknown device %s with %d ports\n",
+				 __func__, sd_np->name, num_pads);
+			return NULL;
+		}
+
+		/*
+		 * we got to this node from this single source port,
+		 * there are no sink pads.
+		 */
+		imxsd->num_sink_pads = 0;
+	}
+
+	if (imxsd->num_sink_pads >= num_pads)
+		return ERR_PTR(-EINVAL);
+
+	imxsd->num_src_pads = num_pads - imxsd->num_sink_pads;
+
+	dev_dbg(imxmd->md.dev, "%s: %s has %d pads (%d sink, %d src)\n",
+		__func__, sd_np->name, num_pads,
+		imxsd->num_sink_pads, imxsd->num_src_pads);
+
+	/*
+	 * With no sink, this subdev node is the original source
+	 * of video, parse it's media bus fur use by the pipeline.
+	 */
+	if (imxsd->num_sink_pads == 0)
+		of_parse_sensor(imxmd, imxsd, sd_np);
+
+	for (i = 0; i < num_pads; i++) {
+		struct device_node *epnode = NULL, *port, *remote_np;
+		struct imx_media_subdev *remote_imxsd;
+		struct imx_media_pad *pad;
+		int remote_pad;
+
+		/* init this pad */
+		pad = &imxsd->pad[i];
+		pad->pad.flags = (i < imxsd->num_sink_pads) ?
+			MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
+
+		if (is_csi_port)
+			port = (i < imxsd->num_sink_pads) ? sd_np : NULL;
+		else
+			port = of_graph_get_port_by_id(sd_np, i);
+		if (!port)
+			continue;
+
+		for_each_child_of_node(port, epnode) {
+			of_get_remote_pad(epnode, &remote_np, &remote_pad);
+			if (!remote_np)
+				continue;
+
+			ret = of_add_pad_link(imxmd, pad, sd_np, remote_np,
+					      i, remote_pad);
+			if (ret) {
+				imxsd = ERR_PTR(ret);
+				break;
+			}
+
+			if (i < imxsd->num_sink_pads) {
+				/* follow sink endpoints upstream */
+				remote_imxsd = of_parse_subdev(imxmd,
+							       remote_np,
+							       false);
+				if (IS_ERR(remote_imxsd)) {
+					imxsd = remote_imxsd;
+					break;
+				}
+			}
+
+			of_node_put(remote_np);
+		}
+
+		if (port != sd_np)
+			of_node_put(port);
+		if (IS_ERR(imxsd)) {
+			of_node_put(remote_np);
+			of_node_put(epnode);
+			break;
+		}
+	}
+
+	return imxsd;
+}
+
+int imx_media_of_parse(struct imx_media_dev *imxmd,
+		       struct imx_media_subdev *(*csi)[4],
+		       struct device_node *np)
+{
+	struct imx_media_subdev *lcsi;
+	struct device_node *csi_np;
+	u32 ipu_id, csi_id;
+	int i, ret;
+
+	for (i = 0; ; i++) {
+		csi_np = of_parse_phandle(np, "ports", i);
+		if (!csi_np)
+			break;
+
+		lcsi = of_parse_subdev(imxmd, csi_np, true);
+		if (IS_ERR(lcsi)) {
+			ret = PTR_ERR(lcsi);
+			goto err_put;
+		}
+
+		ret = of_property_read_u32(csi_np, "reg", &csi_id);
+		if (ret) {
+			dev_err(imxmd->md.dev,
+				"%s: csi port missing reg property!\n",
+				__func__);
+			goto err_put;
+		}
+
+		ipu_id = of_alias_get_id(csi_np->parent, "ipu");
+		of_node_put(csi_np);
+
+		if (ipu_id > 1 || csi_id > 1) {
+			dev_err(imxmd->md.dev,
+				"%s: invalid ipu/csi id (%u/%u)\n",
+				__func__, ipu_id, csi_id);
+			return -EINVAL;
+		}
+
+		(*csi)[ipu_id * 2 + csi_id] = lcsi;
+	}
+
+	return 0;
+err_put:
+	of_node_put(csi_np);
+	return ret;
+}
diff --git a/drivers/staging/media/imx/imx-media-utils.c b/drivers/staging/media/imx/imx-media-utils.c
new file mode 100644
index 0000000..ee50b6a
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media-utils.c
@@ -0,0 +1,766 @@
+/*
+ * V4L2 Media Controller Driver for Freescale i.MX5/6 SOC
+ *
+ * Copyright (c) 2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/module.h>
+#include "imx-media.h"
+
+/*
+ * List of pixel formats for the subdevs. This must be a super-set of
+ * the formats supported by the ipu image converter.
+ *
+ * The non-mbus formats (planar and BGR) must all fall at the end of
+ * this table, otherwise enum_fmt() at media pads will stop before
+ * seeing all the supported mbus formats.
+ */
+static const struct imx_media_pixfmt imx_media_formats[] = {
+	{
+		.fourcc	= V4L2_PIX_FMT_UYVY,
+		.codes  = {
+			MEDIA_BUS_FMT_UYVY8_2X8,
+			MEDIA_BUS_FMT_UYVY8_1X16
+		},
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 16,
+	}, {
+		.fourcc	= V4L2_PIX_FMT_YUYV,
+		.codes  = {
+			MEDIA_BUS_FMT_YUYV8_2X8,
+			MEDIA_BUS_FMT_YUYV8_1X16
+		},
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 16,
+	}, {
+		.fourcc = V4L2_PIX_FMT_YUV32,
+		.codes  = {MEDIA_BUS_FMT_AYUV8_1X32},
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 32,
+		.ipufmt = true,
+	}, {
+		.fourcc	= V4L2_PIX_FMT_RGB565,
+		.codes  = {MEDIA_BUS_FMT_RGB565_2X8_LE},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 16,
+	}, {
+		.fourcc	= V4L2_PIX_FMT_RGB24,
+		.codes  = {
+			MEDIA_BUS_FMT_RGB888_1X24,
+			MEDIA_BUS_FMT_RGB888_2X12_LE
+		},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 24,
+	}, {
+		.fourcc	= V4L2_PIX_FMT_RGB32,
+		.codes  = {MEDIA_BUS_FMT_ARGB8888_1X32},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 32,
+		.ipufmt = true,
+	},
+	/*** non-mbus formats start here ***/
+	{
+		.fourcc	= V4L2_PIX_FMT_BGR24,
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 24,
+	}, {
+		.fourcc	= V4L2_PIX_FMT_BGR32,
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 32,
+	}, {
+		.fourcc	= V4L2_PIX_FMT_YUV420,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 12,
+		.planar = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_YVU420,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 12,
+		.planar = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_YUV422P,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 16,
+		.planar = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_NV12,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 12,
+		.planar = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_NV16,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 16,
+		.planar = true,
+	},
+};
+
+static const u32 imx_media_ipu_internal_codes[] = {
+	MEDIA_BUS_FMT_AYUV8_1X32, MEDIA_BUS_FMT_ARGB8888_1X32,
+};
+
+static inline u32 pixfmt_to_colorspace(const struct imx_media_pixfmt *fmt)
+{
+	return (fmt->cs == IPUV3_COLORSPACE_RGB) ?
+		V4L2_COLORSPACE_SRGB : V4L2_COLORSPACE_SMPTE170M;
+}
+
+static const struct imx_media_pixfmt *find_format(u32 fourcc, u32 code,
+						  bool allow_rgb,
+						  bool allow_planar,
+						  bool ipu_fmt_only)
+{
+	const struct imx_media_pixfmt *fmt, *ret = NULL;
+	int i, j;
+
+	for (i = 0; i < ARRAY_SIZE(imx_media_formats); i++) {
+		fmt = &imx_media_formats[i];
+
+		if (ipu_fmt_only && !fmt->ipufmt)
+			continue;
+
+		if (fourcc && fmt->fourcc == fourcc &&
+		    (fmt->cs != IPUV3_COLORSPACE_RGB || allow_rgb) &&
+		    (!fmt->planar || allow_planar)) {
+			ret = fmt;
+			goto out;
+		}
+
+		for (j = 0; code && fmt->codes[j]; j++) {
+			if (fmt->codes[j] == code && !fmt->planar &&
+			    (fmt->cs != IPUV3_COLORSPACE_RGB || allow_rgb)) {
+				ret = fmt;
+				goto out;
+			}
+		}
+	}
+out:
+	return ret;
+}
+
+const struct imx_media_pixfmt *imx_media_find_format(u32 fourcc, u32 code,
+						     bool allow_rgb,
+						     bool allow_planar)
+{
+	return find_format(fourcc, code, allow_rgb, allow_planar, false);
+}
+EXPORT_SYMBOL_GPL(imx_media_find_format);
+
+const struct imx_media_pixfmt *imx_media_find_ipu_format(u32 fourcc,
+							 u32 code,
+							 bool allow_rgb)
+{
+	return find_format(fourcc, code, allow_rgb, false, true);
+}
+EXPORT_SYMBOL_GPL(imx_media_find_ipu_format);
+
+int imx_media_enum_format(u32 *fourcc, u32 *code, u32 index,
+			  bool allow_rgb, bool allow_planar)
+{
+	const struct imx_media_pixfmt *fmt;
+
+	if (index >= ARRAY_SIZE(imx_media_formats))
+		return -EINVAL;
+
+	fmt = &imx_media_formats[index];
+
+	if ((fmt->cs == IPUV3_COLORSPACE_RGB && !allow_rgb) ||
+	    (fmt->planar && !allow_planar))
+		return -EINVAL;
+
+	if (code)
+		*code = fmt->codes[0];
+	if (fourcc)
+		*fourcc = fmt->fourcc;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_enum_format);
+
+int imx_media_enum_ipu_format(u32 *fourcc, u32 *code, u32 index,
+			      bool allow_rgb)
+{
+	const struct imx_media_pixfmt *fmt;
+	u32 lcode;
+
+	if (index >= ARRAY_SIZE(imx_media_ipu_internal_codes))
+		return -EINVAL;
+
+	lcode = imx_media_ipu_internal_codes[index];
+
+	fmt = find_format(0, lcode, allow_rgb, false, true);
+	if (!fmt)
+		return -EINVAL;
+
+	if (code)
+		*code = fmt->codes[0];
+	if (fourcc)
+		*fourcc = fmt->fourcc;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_enum_ipu_format);
+
+int imx_media_init_mbus_fmt(struct v4l2_mbus_framefmt *mbus,
+			    u32 width, u32 height, u32 code, u32 field,
+			    const struct imx_media_pixfmt **cc)
+{
+	const struct imx_media_pixfmt *lcc;
+
+	mbus->width = width;
+	mbus->height = height;
+	mbus->field = field;
+	if (code == 0)
+		imx_media_enum_format(NULL, &code, 0, true, false);
+	lcc = imx_media_find_format(0, code, true, false);
+	if (!lcc)
+		return -EINVAL;
+	mbus->code = code;
+	mbus->colorspace = pixfmt_to_colorspace(lcc);
+
+	if (cc)
+		*cc = lcc;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_init_mbus_fmt);
+
+int imx_media_mbus_fmt_to_pix_fmt(struct v4l2_pix_format *pix,
+				  struct v4l2_mbus_framefmt *mbus,
+				  const struct imx_media_pixfmt *cc)
+{
+	u32 stride;
+
+	if (!cc) {
+		cc = imx_media_find_format(0, mbus->code, true, false);
+		if (!cc)
+			return -EINVAL;
+	}
+
+	stride = cc->planar ? mbus->width : (mbus->width * cc->bpp) >> 3;
+
+	pix->width = mbus->width;
+	pix->height = mbus->height;
+	pix->pixelformat = cc->fourcc;
+	pix->colorspace = mbus->colorspace;
+	pix->xfer_func = mbus->xfer_func;
+	pix->ycbcr_enc = mbus->ycbcr_enc;
+	pix->quantization = mbus->quantization;
+	pix->field = mbus->field;
+	pix->bytesperline = stride;
+	pix->sizeimage = (pix->width * pix->height * cc->bpp) >> 3;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_mbus_fmt_to_pix_fmt);
+
+int imx_media_mbus_fmt_to_ipu_image(struct ipu_image *image,
+				    struct v4l2_mbus_framefmt *mbus)
+{
+	int ret;
+
+	memset(image, 0, sizeof(*image));
+
+	ret = imx_media_mbus_fmt_to_pix_fmt(&image->pix, mbus, NULL);
+	if (ret)
+		return ret;
+
+	image->rect.width = mbus->width;
+	image->rect.height = mbus->height;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_mbus_fmt_to_ipu_image);
+
+int imx_media_ipu_image_to_mbus_fmt(struct v4l2_mbus_framefmt *mbus,
+				    struct ipu_image *image)
+{
+	const struct imx_media_pixfmt *fmt;
+
+	fmt = imx_media_find_format(image->pix.pixelformat, 0, true, false);
+	if (!fmt)
+		return -EINVAL;
+
+	memset(mbus, 0, sizeof(*mbus));
+	mbus->width = image->pix.width;
+	mbus->height = image->pix.height;
+	mbus->code = fmt->codes[0];
+	mbus->colorspace = pixfmt_to_colorspace(fmt);
+	mbus->field = image->pix.field;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_ipu_image_to_mbus_fmt);
+
+void imx_media_free_dma_buf(struct imx_media_dev *imxmd,
+			    struct imx_media_dma_buf *buf)
+{
+	if (buf->virt)
+		dma_free_coherent(imxmd->md.dev, buf->len,
+				  buf->virt, buf->phys);
+
+	buf->virt = NULL;
+	buf->phys = 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_free_dma_buf);
+
+int imx_media_alloc_dma_buf(struct imx_media_dev *imxmd,
+			    struct imx_media_dma_buf *buf,
+			    int size)
+{
+	imx_media_free_dma_buf(imxmd, buf);
+
+	buf->len = PAGE_ALIGN(size);
+	buf->virt = dma_alloc_coherent(imxmd->md.dev, buf->len, &buf->phys,
+				       GFP_DMA | GFP_KERNEL);
+	if (!buf->virt) {
+		dev_err(imxmd->md.dev, "failed to alloc dma buffer\n");
+		return -ENOMEM;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(imx_media_alloc_dma_buf);
+
+/* form a subdev name given a group id and ipu id */
+void imx_media_grp_id_to_sd_name(char *sd_name, int sz, u32 grp_id, int ipu_id)
+{
+	int id;
+
+	switch (grp_id) {
+	case IMX_MEDIA_GRP_ID_CSI0...IMX_MEDIA_GRP_ID_CSI1:
+		id = (grp_id >> IMX_MEDIA_GRP_ID_CSI_BIT) - 1;
+		snprintf(sd_name, sz, "ipu%d_csi%d", ipu_id + 1, id);
+		break;
+	case IMX_MEDIA_GRP_ID_VDIC:
+		snprintf(sd_name, sz, "ipu%d_vdic", ipu_id + 1);
+		break;
+	case IMX_MEDIA_GRP_ID_IC_PRP:
+		snprintf(sd_name, sz, "ipu%d_ic_prp", ipu_id + 1);
+		break;
+	case IMX_MEDIA_GRP_ID_IC_PRPENC:
+		snprintf(sd_name, sz, "ipu%d_ic_prpenc", ipu_id + 1);
+		break;
+	case IMX_MEDIA_GRP_ID_IC_PRPVF:
+		snprintf(sd_name, sz, "ipu%d_ic_prpvf", ipu_id + 1);
+		break;
+	default:
+		break;
+	}
+}
+EXPORT_SYMBOL_GPL(imx_media_grp_id_to_sd_name);
+
+struct imx_media_subdev *
+imx_media_find_subdev_by_sd(struct imx_media_dev *imxmd,
+			    struct v4l2_subdev *sd)
+{
+	struct imx_media_subdev *imxsd;
+	int i;
+
+	for (i = 0; i < imxmd->num_subdevs; i++) {
+		imxsd = &imxmd->subdev[i];
+		if (sd == imxsd->sd)
+			return imxsd;
+	}
+
+	return ERR_PTR(-ENODEV);
+}
+EXPORT_SYMBOL_GPL(imx_media_find_subdev_by_sd);
+
+struct imx_media_subdev *
+imx_media_find_subdev_by_id(struct imx_media_dev *imxmd, u32 grp_id)
+{
+	struct imx_media_subdev *imxsd;
+	int i;
+
+	for (i = 0; i < imxmd->num_subdevs; i++) {
+		imxsd = &imxmd->subdev[i];
+		if (imxsd->sd && imxsd->sd->grp_id == grp_id)
+			return imxsd;
+	}
+
+	return ERR_PTR(-ENODEV);
+}
+EXPORT_SYMBOL_GPL(imx_media_find_subdev_by_id);
+
+/*
+ * Search for an entity in the current pipeline, either a subdev
+ * with given grp_id, or a video device if vdev is true.
+ * Called with mdev->graph_mutex held.
+ */
+static struct media_entity *
+find_pipeline_entity(struct imx_media_dev *imxmd,
+		     struct media_graph *graph,
+		     struct media_entity *start_entity,
+		     u32 grp_id, bool vdev)
+{
+	struct media_entity *entity;
+	struct v4l2_subdev *sd;
+
+	media_graph_walk_start(graph, start_entity);
+
+	while ((entity = media_graph_walk_next(graph))) {
+		if ((vdev && !is_media_entity_v4l2_video_device(entity)) ||
+		    (!vdev && !is_media_entity_v4l2_subdev(entity)))
+			continue;
+
+		if (vdev)
+			return entity;
+
+		sd = media_entity_to_v4l2_subdev(entity);
+		if (sd->grp_id & grp_id)
+			return entity;
+	}
+
+	return NULL;
+}
+
+/*
+ * Search for a subdev in the current pipeline with given grp_id.
+ * Called with mdev->graph_mutex held.
+ */
+static struct v4l2_subdev *
+find_pipeline_subdev(struct imx_media_dev *imxmd,
+		     struct media_graph *graph,
+		     struct media_entity *start_entity,
+		     u32 grp_id)
+{
+	struct media_entity *entity = find_pipeline_entity(imxmd, graph,
+							   start_entity,
+							   grp_id, false);
+	return entity ? media_entity_to_v4l2_subdev(entity) : NULL;
+}
+
+/*
+ * Search for a video device in the current pipeline.
+ * Called with mdev->graph_mutex held.
+ */
+static struct video_device *
+find_pipeline_vdev(struct imx_media_dev *imxmd,
+		   struct media_graph *graph,
+		   struct media_entity *start_entity)
+{
+	struct media_entity *entity = find_pipeline_entity(imxmd, graph,
+							   start_entity,
+							   0, true);
+	return entity ? media_entity_to_video_device(entity) : NULL;
+}
+
+/*
+ * Search for an entity in the current pipeline with given grp_id,
+ * then locate the remote enabled source pad from that entity.
+ * Called with mdev->graph_mutex held.
+ */
+static struct media_pad *
+find_pipeline_remote_source_pad(struct imx_media_dev *imxmd,
+				struct media_graph *graph,
+				struct media_entity *start_entity,
+				u32 grp_id)
+{
+	struct media_pad *pad = NULL;
+	struct media_entity *me;
+	struct v4l2_subdev *sd;
+	int i;
+
+	sd = find_pipeline_subdev(imxmd, graph, start_entity, grp_id);
+	if (!sd)
+		return NULL;
+	me = &sd->entity;
+
+	/* Find remote source pad */
+	for (i = 0; i < me->num_pads; i++) {
+		struct media_pad *spad = &me->pads[i];
+
+		if (!(spad->flags & MEDIA_PAD_FL_SINK))
+			continue;
+		pad = media_entity_remote_pad(spad);
+		if (pad)
+			return pad;
+	}
+
+	return NULL;
+}
+
+/*
+ * Find the mipi-csi2 virtual channel reached from the given
+ * start entity in the current pipeline.
+ * Must be called with mdev->graph_mutex held.
+ */
+int imx_media_find_mipi_csi2_channel(struct imx_media_dev *imxmd,
+				     struct media_entity *start_entity)
+{
+	struct media_graph graph;
+	struct v4l2_subdev *sd;
+	struct media_pad *pad;
+	int ret;
+
+	ret = media_graph_walk_init(&graph, &imxmd->md);
+	if (ret)
+		return ret;
+
+	/* first try to locate the mipi-csi2 from the video mux */
+	pad = find_pipeline_remote_source_pad(imxmd, &graph, start_entity,
+					      IMX_MEDIA_GRP_ID_VIDMUX);
+	/* if couldn't reach it from there, try from a CSI */
+	if (!pad)
+		pad = find_pipeline_remote_source_pad(imxmd, &graph,
+						      start_entity,
+						      IMX_MEDIA_GRP_ID_CSI);
+	if (pad) {
+		sd = media_entity_to_v4l2_subdev(pad->entity);
+		if (sd->grp_id & IMX_MEDIA_GRP_ID_CSI2) {
+			ret = pad->index - 1; /* found it! */
+			dev_dbg(imxmd->md.dev, "found vc%d from %s\n",
+				ret, start_entity->name);
+			goto cleanup;
+		}
+	}
+
+	ret = -EPIPE;
+
+cleanup:
+	media_graph_walk_cleanup(&graph);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(imx_media_find_mipi_csi2_channel);
+
+/*
+ * Find a subdev reached from the given start entity in the
+ * current pipeline.
+ * Must be called with mdev->graph_mutex held.
+ */
+struct imx_media_subdev *
+imx_media_find_pipeline_subdev(struct imx_media_dev *imxmd,
+			       struct media_entity *start_entity,
+			       u32 grp_id)
+{
+	struct imx_media_subdev *imxsd;
+	struct media_graph graph;
+	struct v4l2_subdev *sd;
+	int ret;
+
+	ret = media_graph_walk_init(&graph, &imxmd->md);
+	if (ret)
+		return ERR_PTR(ret);
+
+	sd = find_pipeline_subdev(imxmd, &graph, start_entity, grp_id);
+	if (!sd) {
+		imxsd = ERR_PTR(-ENODEV);
+		goto cleanup;
+	}
+
+	imxsd = imx_media_find_subdev_by_sd(imxmd, sd);
+cleanup:
+	media_graph_walk_cleanup(&graph);
+	return imxsd;
+}
+EXPORT_SYMBOL_GPL(imx_media_find_pipeline_subdev);
+
+/*
+ * Find a video device reached from the given start entity in the
+ * current pipeline.
+ * Must be called with mdev->graph_mutex held.
+ */
+struct video_device *
+imx_media_find_pipeline_video_device(struct imx_media_dev *imxmd,
+				     struct media_entity *start_entity)
+{
+	struct video_device *vdev;
+	struct media_graph graph;
+	int ret;
+
+	ret = media_graph_walk_init(&graph, &imxmd->md);
+	if (ret)
+		return ERR_PTR(ret);
+
+	vdev = find_pipeline_vdev(imxmd, &graph, start_entity);
+	if (!vdev)
+		vdev = ERR_PTR(-ENODEV);
+
+	media_graph_walk_cleanup(&graph);
+	return vdev;
+}
+EXPORT_SYMBOL_GPL(imx_media_find_pipeline_video_device);
+
+struct imx_media_subdev *
+__imx_media_find_sensor(struct imx_media_dev *imxmd,
+			struct media_entity *start_entity)
+{
+	return imx_media_find_pipeline_subdev(imxmd, start_entity,
+					      IMX_MEDIA_GRP_ID_SENSOR);
+}
+EXPORT_SYMBOL_GPL(__imx_media_find_sensor);
+
+struct imx_media_subdev *
+imx_media_find_sensor(struct imx_media_dev *imxmd,
+		      struct media_entity *start_entity)
+{
+	struct imx_media_subdev *sensor;
+
+	mutex_lock(&imxmd->md.graph_mutex);
+	sensor = __imx_media_find_sensor(imxmd, start_entity);
+	mutex_unlock(&imxmd->md.graph_mutex);
+
+	return sensor;
+}
+EXPORT_SYMBOL_GPL(imx_media_find_sensor);
+
+/*
+ * The subdevs have to be powered on/off, and streaming
+ * enabled/disabled, in a specific sequence.
+ */
+static const u32 stream_on_seq[] = {
+	IMX_MEDIA_GRP_ID_IC_PRPVF,
+	IMX_MEDIA_GRP_ID_IC_PRPENC,
+	IMX_MEDIA_GRP_ID_IC_PRP,
+	IMX_MEDIA_GRP_ID_VDIC,
+	IMX_MEDIA_GRP_ID_CSI2,
+	IMX_MEDIA_GRP_ID_SENSOR,
+	IMX_MEDIA_GRP_ID_VIDMUX,
+	IMX_MEDIA_GRP_ID_CSI,
+};
+
+static const u32 stream_off_seq[] = {
+	IMX_MEDIA_GRP_ID_IC_PRPVF,
+	IMX_MEDIA_GRP_ID_IC_PRPENC,
+	IMX_MEDIA_GRP_ID_IC_PRP,
+	IMX_MEDIA_GRP_ID_VDIC,
+	IMX_MEDIA_GRP_ID_CSI,
+	IMX_MEDIA_GRP_ID_VIDMUX,
+	IMX_MEDIA_GRP_ID_SENSOR,
+	IMX_MEDIA_GRP_ID_CSI2,
+};
+
+#define NUM_STREAM_ENTITIES ARRAY_SIZE(stream_on_seq)
+
+static const u32 power_on_seq[] = {
+	IMX_MEDIA_GRP_ID_CSI2,
+	IMX_MEDIA_GRP_ID_SENSOR,
+	IMX_MEDIA_GRP_ID_VIDMUX,
+	IMX_MEDIA_GRP_ID_CSI,
+	IMX_MEDIA_GRP_ID_VDIC,
+	IMX_MEDIA_GRP_ID_IC_PRPENC,
+	IMX_MEDIA_GRP_ID_IC_PRPVF,
+};
+
+static const u32 power_off_seq[] = {
+	IMX_MEDIA_GRP_ID_IC_PRPVF,
+	IMX_MEDIA_GRP_ID_IC_PRPENC,
+	IMX_MEDIA_GRP_ID_VDIC,
+	IMX_MEDIA_GRP_ID_CSI,
+	IMX_MEDIA_GRP_ID_VIDMUX,
+	IMX_MEDIA_GRP_ID_SENSOR,
+	IMX_MEDIA_GRP_ID_CSI2,
+};
+
+#define NUM_POWER_ENTITIES ARRAY_SIZE(power_on_seq)
+
+static int imx_media_set_stream(struct imx_media_dev *imxmd,
+				struct media_entity *start_entity,
+				bool on)
+{
+	struct media_graph graph;
+	struct v4l2_subdev *sd;
+	int i, ret;
+	u32 id;
+
+	mutex_lock(&imxmd->md.graph_mutex);
+
+	ret = media_graph_walk_init(&graph, &imxmd->md);
+	if (ret)
+		goto unlock;
+
+	for (i = 0; i < NUM_STREAM_ENTITIES; i++) {
+		id = on ? stream_on_seq[i] : stream_off_seq[i];
+		sd = find_pipeline_subdev(imxmd, &graph,
+					  start_entity, id);
+		if (!sd)
+			continue;
+
+		ret = v4l2_subdev_call(sd, video, s_stream, on);
+		if (on && ret && ret != -ENOIOCTLCMD)
+			break;
+	}
+
+	media_graph_walk_cleanup(&graph);
+unlock:
+	mutex_unlock(&imxmd->md.graph_mutex);
+
+	return (on && ret && ret != -ENOIOCTLCMD) ? ret : 0;
+}
+
+/*
+ * Turn current pipeline streaming on/off starting from entity.
+ */
+int imx_media_pipeline_set_stream(struct imx_media_dev *imxmd,
+				  struct media_entity *entity,
+				  struct media_pipeline *pipe,
+				  bool on)
+{
+	int ret = 0;
+
+	if (on) {
+		ret = media_pipeline_start(entity, pipe);
+		if (ret)
+			return ret;
+		ret = imx_media_set_stream(imxmd, entity, true);
+		if (!ret)
+			return 0;
+		/* fall through */
+	}
+
+	imx_media_set_stream(imxmd, entity, false);
+	if (entity->pipe)
+		media_pipeline_stop(entity);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(imx_media_pipeline_set_stream);
+
+static int imx_media_set_power(struct imx_media_dev *imxmd,
+			       struct media_graph *graph,
+			       struct media_entity *start_entity, bool on)
+{
+	struct v4l2_subdev *sd;
+	int i, ret = 0;
+	u32 id;
+
+	for (i = 0; i < NUM_POWER_ENTITIES; i++) {
+		id = on ? power_on_seq[i] : power_off_seq[i];
+		sd = find_pipeline_subdev(imxmd, graph, start_entity, id);
+		if (!sd)
+			continue;
+
+		ret = v4l2_subdev_call(sd, core, s_power, on);
+		if (on && ret && ret != -ENOIOCTLCMD)
+			break;
+	}
+
+	return (on && ret && ret != -ENOIOCTLCMD) ? ret : 0;
+}
+
+/*
+ * Turn current pipeline power on/off starting from start_entity.
+ * Must be called with mdev->graph_mutex held.
+ */
+int imx_media_pipeline_set_power(struct imx_media_dev *imxmd,
+				 struct media_graph *graph,
+				 struct media_entity *start_entity, bool on)
+{
+	int ret;
+
+	ret = imx_media_set_power(imxmd, graph, start_entity, on);
+	if (ret)
+		imx_media_set_power(imxmd, graph, start_entity, false);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(imx_media_pipeline_set_power);
+
+MODULE_DESCRIPTION("i.MX5/6 v4l2 media controller driver");
+MODULE_AUTHOR("Steve Longerbeam <steve_longerbeam@mentor.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/staging/media/imx/imx-media.h b/drivers/staging/media/imx/imx-media.h
new file mode 100644
index 0000000..2dd48ea
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media.h
@@ -0,0 +1,303 @@
+/*
+ * V4L2 Media Controller Driver for Freescale i.MX5/6 SOC
+ *
+ * Copyright (c) 2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#ifndef _IMX_MEDIA_H
+#define _IMX_MEDIA_H
+
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-of.h>
+#include <media/v4l2-subdev.h>
+#include <media/videobuf2-dma-contig.h>
+#include <video/imx-ipu-v3.h>
+
+/*
+ * This is somewhat arbitrary, but we need at least:
+ * - 2 camera interface subdevs
+ * - 3 IC subdevs
+ * - 2 CSI subdevs
+ * - 1 mipi-csi2 receiver subdev
+ * - 2 video-mux subdevs
+ * - 3 camera sensor subdevs (2 parallel, 1 mipi-csi2)
+ *
+ * And double the above numbers for quad i.mx!
+ */
+#define IMX_MEDIA_MAX_SUBDEVS       48
+/* max pads per subdev */
+#define IMX_MEDIA_MAX_PADS          16
+/* max links per pad */
+#define IMX_MEDIA_MAX_LINKS          8
+
+/*
+ * Pad definitions for the subdevs with multiple source or
+ * sink pads
+ */
+/* ipu_csi */
+enum {
+	CSI_SINK_PAD = 0,
+	CSI_SRC_PAD_DIRECT,
+	CSI_SRC_PAD_IDMAC,
+	CSI_NUM_PADS,
+};
+
+#define CSI_NUM_SINK_PADS 1
+#define CSI_NUM_SRC_PADS  2
+
+/* ipu_vdic */
+enum {
+	VDIC_SINK_PAD_DIRECT = 0,
+	VDIC_SINK_PAD_IDMAC,
+	VDIC_SRC_PAD_DIRECT,
+	VDIC_NUM_PADS,
+};
+
+#define VDIC_NUM_SINK_PADS 2
+#define VDIC_NUM_SRC_PADS  1
+
+/* ipu_ic_prp */
+enum {
+	PRP_SINK_PAD = 0,
+	PRP_SRC_PAD_PRPENC,
+	PRP_SRC_PAD_PRPVF,
+	PRP_NUM_PADS,
+};
+
+#define PRP_NUM_SINK_PADS 1
+#define PRP_NUM_SRC_PADS  2
+
+/* ipu_ic_prpencvf */
+enum {
+	PRPENCVF_SINK_PAD = 0,
+	PRPENCVF_SRC_PAD,
+	PRPENCVF_NUM_PADS,
+};
+
+#define PRPENCVF_NUM_SINK_PADS 1
+#define PRPENCVF_NUM_SRC_PADS  1
+
+/* How long to wait for EOF interrupts in the buffer-capture subdevs */
+#define IMX_MEDIA_EOF_TIMEOUT       1000
+
+struct imx_media_pixfmt {
+	u32     fourcc;
+	u32     codes[4];
+	int     bpp;     /* total bpp */
+	enum ipu_color_space cs;
+	bool    planar;  /* is a planar format */
+	bool    ipufmt;  /* is one of the IPU internal formats */
+};
+
+struct imx_media_buffer {
+	struct vb2_v4l2_buffer vbuf; /* v4l buffer must be first */
+	struct list_head  list;
+};
+
+struct imx_media_video_dev {
+	struct video_device *vfd;
+
+	/* the user format */
+	struct v4l2_format fmt;
+	const struct imx_media_pixfmt *cc;
+};
+
+static inline struct imx_media_buffer *to_imx_media_vb(struct vb2_buffer *vb)
+{
+	struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb);
+
+	return container_of(vbuf, struct imx_media_buffer, vbuf);
+}
+
+struct imx_media_link {
+	struct device_node *remote_sd_node;
+	char               remote_devname[32];
+	int                local_pad;
+	int                remote_pad;
+};
+
+struct imx_media_pad {
+	struct media_pad  pad;
+	struct imx_media_link link[IMX_MEDIA_MAX_LINKS];
+	bool devnode; /* does this pad link to a device node */
+	int num_links;
+};
+
+struct imx_media_internal_sd_platformdata {
+	char sd_name[V4L2_SUBDEV_NAME_SIZE];
+	u32 grp_id;
+	int ipu_id;
+};
+
+struct imx_media_subdev {
+	struct v4l2_async_subdev asd;
+	struct v4l2_subdev       *sd; /* set when bound */
+
+	struct imx_media_pad     pad[IMX_MEDIA_MAX_PADS];
+	int num_sink_pads;
+	int num_src_pads;
+
+	/* the platform device if this is an internal subdev */
+	struct platform_device *pdev;
+	/* the devname is needed for async devname match */
+	char devname[32];
+
+	/* if this is a sensor */
+	struct v4l2_of_endpoint sensor_ep;
+};
+
+struct imx_media_dev {
+	struct media_device md;
+	struct v4l2_device  v4l2_dev;
+
+	/* master subdev list */
+	struct imx_media_subdev subdev[IMX_MEDIA_MAX_SUBDEVS];
+	int num_subdevs;
+
+	/* IPUs this media driver control, valid after subdevs bound */
+	struct ipu_soc *ipu[2];
+
+	/* used during link_notify */
+	struct media_graph link_notify_graph;
+
+	/* for async subdev registration */
+	struct v4l2_async_subdev *async_ptrs[IMX_MEDIA_MAX_SUBDEVS];
+	struct v4l2_async_notifier subdev_notifier;
+};
+
+const struct imx_media_pixfmt *imx_media_find_format(u32 fourcc, u32 code,
+						     bool allow_rgb,
+						     bool allow_planar);
+const struct imx_media_pixfmt *imx_media_find_ipu_format(u32 fourcc, u32 code,
+							 bool allow_rgb);
+
+int imx_media_enum_format(u32 *fourcc, u32 *code, u32 index,
+			  bool allow_rgb, bool allow_planar);
+int imx_media_enum_ipu_format(u32 *fourcc, u32 *code, u32 index,
+			      bool allow_rgb);
+
+int imx_media_init_mbus_fmt(struct v4l2_mbus_framefmt *mbus,
+			    u32 width, u32 height, u32 code, u32 field,
+			    const struct imx_media_pixfmt **cc);
+
+int imx_media_mbus_fmt_to_pix_fmt(struct v4l2_pix_format *pix,
+				  struct v4l2_mbus_framefmt *mbus,
+				  const struct imx_media_pixfmt *cc);
+int imx_media_mbus_fmt_to_ipu_image(struct ipu_image *image,
+				    struct v4l2_mbus_framefmt *mbus);
+int imx_media_ipu_image_to_mbus_fmt(struct v4l2_mbus_framefmt *mbus,
+				    struct ipu_image *image);
+
+struct imx_media_subdev *
+imx_media_find_async_subdev(struct imx_media_dev *imxmd,
+			    struct device_node *np,
+			    const char *devname);
+struct imx_media_subdev *
+imx_media_add_async_subdev(struct imx_media_dev *imxmd,
+			   struct device_node *np,
+			   struct platform_device *pdev);
+int imx_media_add_pad_link(struct imx_media_dev *imxmd,
+			   struct imx_media_pad *pad,
+			   struct device_node *remote_node,
+			   const char *remote_devname,
+			   int local_pad, int remote_pad);
+
+void imx_media_grp_id_to_sd_name(char *sd_name, int sz,
+				 u32 grp_id, int ipu_id);
+
+int imx_media_add_internal_subdevs(struct imx_media_dev *imxmd,
+				   struct imx_media_subdev *csi[4]);
+void imx_media_remove_internal_subdevs(struct imx_media_dev *imxmd);
+
+struct imx_media_subdev *
+imx_media_find_subdev_by_sd(struct imx_media_dev *imxmd,
+			    struct v4l2_subdev *sd);
+struct imx_media_subdev *
+imx_media_find_subdev_by_id(struct imx_media_dev *imxmd,
+			    u32 grp_id);
+int imx_media_find_mipi_csi2_channel(struct imx_media_dev *imxmd,
+				     struct media_entity *start_entity);
+struct imx_media_subdev *
+imx_media_find_pipeline_subdev(struct imx_media_dev *imxmd,
+			       struct media_entity *start_entity,
+			       u32 grp_id);
+struct video_device *
+imx_media_find_pipeline_video_device(struct imx_media_dev *imxmd,
+				     struct media_entity *start_entity);
+struct imx_media_subdev *
+__imx_media_find_sensor(struct imx_media_dev *imxmd,
+			struct media_entity *start_entity);
+struct imx_media_subdev *
+imx_media_find_sensor(struct imx_media_dev *imxmd,
+		      struct media_entity *start_entity);
+
+struct imx_media_dma_buf {
+	void          *virt;
+	dma_addr_t     phys;
+	unsigned long  len;
+};
+
+void imx_media_free_dma_buf(struct imx_media_dev *imxmd,
+			    struct imx_media_dma_buf *buf);
+int imx_media_alloc_dma_buf(struct imx_media_dev *imxmd,
+			    struct imx_media_dma_buf *buf,
+			    int size);
+
+int imx_media_pipeline_set_power(struct imx_media_dev *imxmd,
+				 struct media_graph *graph,
+				 struct media_entity *entity, bool on);
+int imx_media_pipeline_set_stream(struct imx_media_dev *imxmd,
+				  struct media_entity *entity,
+				  struct media_pipeline *pipe,
+				  bool on);
+
+/* imx-media-fim.c */
+struct imx_media_fim;
+void imx_media_fim_eof_monitor(struct imx_media_fim *fim, struct timespec *ts);
+int imx_media_fim_set_power(struct imx_media_fim *fim, bool on);
+int imx_media_fim_set_stream(struct imx_media_fim *fim,
+			     struct imx_media_subdev *sensor,
+			     bool on);
+struct imx_media_fim *imx_media_fim_init(struct v4l2_subdev *sd);
+void imx_media_fim_free(struct imx_media_fim *fim);
+
+/* imx-media-of.c */
+struct imx_media_subdev *
+imx_media_of_find_subdev(struct imx_media_dev *imxmd,
+			 struct device_node *np,
+			 const char *name);
+int imx_media_of_parse(struct imx_media_dev *dev,
+		       struct imx_media_subdev *(*csi)[4],
+		       struct device_node *np);
+
+/* imx-media-capture.c */
+struct imx_media_video_dev *
+imx_media_capture_device_init(struct v4l2_subdev *src_sd, int pad);
+void imx_media_capture_device_remove(struct imx_media_video_dev *vdev);
+int imx_media_capture_device_register(struct imx_media_video_dev *vdev);
+void imx_media_capture_device_unregister(struct imx_media_video_dev *vdev);
+struct imx_media_buffer *
+imx_media_capture_device_next_buf(struct imx_media_video_dev *vdev);
+void imx_media_capture_device_set_format(struct imx_media_video_dev *vdev,
+					 struct v4l2_pix_format *pix);
+void imx_media_capture_device_error(struct imx_media_video_dev *vdev);
+
+/* subdev group ids */
+#define IMX_MEDIA_GRP_ID_SENSOR    (1 << 8)
+#define IMX_MEDIA_GRP_ID_VIDMUX    (1 << 9)
+#define IMX_MEDIA_GRP_ID_CSI2      (1 << 10)
+#define IMX_MEDIA_GRP_ID_CSI_BIT   11
+#define IMX_MEDIA_GRP_ID_CSI       (0x3 << IMX_MEDIA_GRP_ID_CSI_BIT)
+#define IMX_MEDIA_GRP_ID_CSI0      (1 << IMX_MEDIA_GRP_ID_CSI_BIT)
+#define IMX_MEDIA_GRP_ID_CSI1      (2 << IMX_MEDIA_GRP_ID_CSI_BIT)
+#define IMX_MEDIA_GRP_ID_VDIC      (1 << 13)
+#define IMX_MEDIA_GRP_ID_IC_PRP    (1 << 14)
+#define IMX_MEDIA_GRP_ID_IC_PRPENC (1 << 15)
+#define IMX_MEDIA_GRP_ID_IC_PRPVF  (1 << 16)
+
+#endif
diff --git a/include/media/imx.h b/include/media/imx.h
new file mode 100644
index 0000000..5025a72
--- /dev/null
+++ b/include/media/imx.h
@@ -0,0 +1,15 @@
+/*
+ * Copyright (c) 2014-2015 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version
+ */
+
+#ifndef __MEDIA_IMX_H__
+#define __MEDIA_IMX_H__
+
+#include <uapi/media/imx.h>
+
+#endif
diff --git a/include/uapi/linux/v4l2-controls.h b/include/uapi/linux/v4l2-controls.h
index 0d2e1e0..6c29f42 100644
--- a/include/uapi/linux/v4l2-controls.h
+++ b/include/uapi/linux/v4l2-controls.h
@@ -180,6 +180,10 @@ enum v4l2_colorfx {
  * We reserve 16 controls for this driver. */
 #define V4L2_CID_USER_TC358743_BASE		(V4L2_CID_USER_BASE + 0x1080)
 
+/* The base for the imx driver controls.
+ * We reserve 16 controls for this driver. */
+#define V4L2_CID_USER_IMX_BASE			(V4L2_CID_USER_BASE + 0x1090)
+
 /* MPEG-class control IDs */
 /* The MPEG controls are applicable to all codec controls
  * and the 'MPEG' part of the define is historical */
-- 
2.7.4

[PATCH v5 24/39] media: imx: Add Capture Device Interface

[Steve Longerbeam]

This is the capture device interface driver that provides the v4l2
user interface. Frames can be received from various sources:

- directly from CSI for capturing unconverted images directly from
  camera sensors.

- from the IC pre-process encode task.

- from the IC pre-process viewfinder task.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/Makefile            |   1 +
 drivers/staging/media/imx/imx-media-capture.c | 655 ++++++++++++++++++++++++++
 2 files changed, 656 insertions(+)
 create mode 100644 drivers/staging/media/imx/imx-media-capture.c

diff --git a/drivers/staging/media/imx/Makefile b/drivers/staging/media/imx/Makefile
index ddd7d94..4606a3a 100644
--- a/drivers/staging/media/imx/Makefile
+++ b/drivers/staging/media/imx/Makefile
@@ -3,3 +3,4 @@ imx-media-common-objs := imx-media-utils.o imx-media-fim.o
 
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-common.o
+obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-capture.o
diff --git a/drivers/staging/media/imx/imx-media-capture.c b/drivers/staging/media/imx/imx-media-capture.c
new file mode 100644
index 0000000..704ed85
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media-capture.c
@@ -0,0 +1,655 @@
+/*
+ * Video Capture Subdev for Freescale i.MX5/6 SOC
+ *
+ * Copyright (c) 2012-2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/delay.h>
+#include <linux/fs.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/platform_device.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/timer.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-ioctl.h>
+#include <media/v4l2-of.h>
+#include <media/v4l2-mc.h>
+#include <media/v4l2-subdev.h>
+#include <media/videobuf2-dma-contig.h>
+#include <video/imx-ipu-v3.h>
+#include <media/imx.h>
+#include "imx-media.h"
+
+struct capture_priv {
+	struct imx_media_video_dev vdev;
+
+	struct v4l2_subdev    *src_sd;
+	int                   src_sd_pad;
+	struct device         *dev;
+
+	struct media_pipeline mp;
+	struct imx_media_dev  *md;
+
+	struct media_pad      vdev_pad;
+
+	struct mutex          mutex;       /* capture device mutex */
+
+	/* the videobuf2 queue */
+	struct vb2_queue       q;
+	/* list of ready imx_media_buffer's from q */
+	struct list_head       ready_q;
+	/* protect ready_q */
+	spinlock_t             q_lock;
+
+	/* controls inherited from subdevs */
+	struct v4l2_ctrl_handler ctrl_hdlr;
+
+	/* misc status */
+	bool                  stop;          /* streaming is stopping */
+};
+
+#define to_capture_priv(v) container_of(v, struct capture_priv, vdev)
+
+/* In bytes, per queue */
+#define VID_MEM_LIMIT	SZ_64M
+
+static struct vb2_ops capture_qops;
+
+/*
+ * Video ioctls follow
+ */
+
+static int vidioc_querycap(struct file *file, void *fh,
+			   struct v4l2_capability *cap)
+{
+	struct capture_priv *priv = video_drvdata(file);
+
+	strncpy(cap->driver, "imx-media-capture", sizeof(cap->driver) - 1);
+	strncpy(cap->card, "imx-media-capture", sizeof(cap->card) - 1);
+	snprintf(cap->bus_info, sizeof(cap->bus_info),
+		 "platform:%s", dev_name(priv->dev));
+
+	return 0;
+}
+
+static int capture_enum_fmt_vid_cap(struct file *file, void *fh,
+				    struct v4l2_fmtdesc *f)
+{
+	u32 fourcc;
+	int ret;
+
+	ret = imx_media_enum_format(&fourcc, NULL, f->index, true, true);
+	if (ret)
+		return ret;
+
+	f->pixelformat = fourcc;
+
+	return 0;
+}
+
+static int capture_g_fmt_vid_cap(struct file *file, void *fh,
+				 struct v4l2_format *f)
+{
+	struct capture_priv *priv = video_drvdata(file);
+
+	*f = priv->vdev.fmt;
+
+	return 0;
+}
+
+static int capture_try_fmt_vid_cap(struct file *file, void *fh,
+				   struct v4l2_format *f)
+{
+	struct capture_priv *priv = video_drvdata(file);
+	struct v4l2_subdev_format fmt_src;
+	const struct imx_media_pixfmt *cc, *src_cc;
+	u32 fourcc;
+	int ret;
+
+	fourcc = f->fmt.pix.pixelformat;
+	cc = imx_media_find_format(fourcc, 0, true, true);
+	if (!cc) {
+		imx_media_enum_format(&fourcc, NULL, 0, true, true);
+		cc = imx_media_find_format(fourcc, 0, true, true);
+	}
+
+	/*
+	 * user frame dimensions are the same as src_sd's pad.
+	 */
+	fmt_src.pad = priv->src_sd_pad;
+	fmt_src.which = V4L2_SUBDEV_FORMAT_ACTIVE;
+	ret = v4l2_subdev_call(priv->src_sd, pad, get_fmt, NULL, &fmt_src);
+	if (ret)
+		return ret;
+
+	/*
+	 * but we can allow planar pixel formats if the src_sd's
+	 * pad configured a YUV format
+	 */
+	src_cc = imx_media_find_format(0, fmt_src.format.code, true, false);
+	if (src_cc->cs == IPUV3_COLORSPACE_YUV &&
+	    cc->cs == IPUV3_COLORSPACE_YUV) {
+		imx_media_mbus_fmt_to_pix_fmt(&f->fmt.pix,
+					      &fmt_src.format, cc);
+	} else {
+		imx_media_mbus_fmt_to_pix_fmt(&f->fmt.pix,
+					      &fmt_src.format, src_cc);
+	}
+
+	return 0;
+}
+
+static int capture_s_fmt_vid_cap(struct file *file, void *fh,
+				 struct v4l2_format *f)
+{
+	struct capture_priv *priv = video_drvdata(file);
+	int ret;
+
+	if (vb2_is_busy(&priv->q)) {
+		v4l2_err(priv->src_sd, "%s queue busy\n", __func__);
+		return -EBUSY;
+	}
+
+	ret = capture_try_fmt_vid_cap(file, priv, f);
+	if (ret)
+		return ret;
+
+	priv->vdev.fmt.fmt.pix = f->fmt.pix;
+	priv->vdev.cc = imx_media_find_format(f->fmt.pix.pixelformat, 0,
+					      true, true);
+
+	return 0;
+}
+
+static int capture_querystd(struct file *file, void *fh, v4l2_std_id *std)
+{
+	struct capture_priv *priv = video_drvdata(file);
+
+	return v4l2_subdev_call(priv->src_sd, video, querystd, std);
+}
+
+static int capture_g_std(struct file *file, void *fh, v4l2_std_id *std)
+{
+	struct capture_priv *priv = video_drvdata(file);
+
+	return v4l2_subdev_call(priv->src_sd, video, g_std, std);
+}
+
+static int capture_s_std(struct file *file, void *fh, v4l2_std_id std)
+{
+	struct capture_priv *priv = video_drvdata(file);
+
+	if (vb2_is_busy(&priv->q))
+		return -EBUSY;
+
+	return v4l2_subdev_call(priv->src_sd, video, s_std, std);
+}
+
+static int capture_g_parm(struct file *file, void *fh,
+			  struct v4l2_streamparm *a)
+{
+	struct capture_priv *priv = video_drvdata(file);
+	struct v4l2_subdev_frame_interval fi;
+	int ret;
+
+	if (a->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+		return -EINVAL;
+
+	memset(&fi, 0, sizeof(fi));
+	fi.pad = priv->src_sd_pad;
+	ret = v4l2_subdev_call(priv->src_sd, video, g_frame_interval, &fi);
+	if (ret < 0)
+		return ret;
+
+	a->parm.capture.capability = V4L2_CAP_TIMEPERFRAME;
+	a->parm.capture.timeperframe = fi.interval;
+
+	return 0;
+}
+
+static int capture_s_parm(struct file *file, void *fh,
+			  struct v4l2_streamparm *a)
+{
+	struct capture_priv *priv = video_drvdata(file);
+	struct v4l2_subdev_frame_interval fi;
+	int ret;
+
+	if (a->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+		return -EINVAL;
+
+	memset(&fi, 0, sizeof(fi));
+	fi.pad = priv->src_sd_pad;
+	fi.interval = a->parm.capture.timeperframe;
+	ret = v4l2_subdev_call(priv->src_sd, video, s_frame_interval, &fi);
+	if (ret < 0)
+		return ret;
+
+	a->parm.capture.capability = V4L2_CAP_TIMEPERFRAME;
+	a->parm.capture.timeperframe = fi.interval;
+
+	return 0;
+}
+
+static const struct v4l2_ioctl_ops capture_ioctl_ops = {
+	.vidioc_querycap	= vidioc_querycap,
+
+	.vidioc_enum_fmt_vid_cap        = capture_enum_fmt_vid_cap,
+	.vidioc_g_fmt_vid_cap           = capture_g_fmt_vid_cap,
+	.vidioc_try_fmt_vid_cap         = capture_try_fmt_vid_cap,
+	.vidioc_s_fmt_vid_cap           = capture_s_fmt_vid_cap,
+
+	.vidioc_querystd        = capture_querystd,
+	.vidioc_g_std           = capture_g_std,
+	.vidioc_s_std           = capture_s_std,
+
+	.vidioc_g_parm          = capture_g_parm,
+	.vidioc_s_parm          = capture_s_parm,
+
+	.vidioc_reqbufs		= vb2_ioctl_reqbufs,
+	.vidioc_create_bufs     = vb2_ioctl_create_bufs,
+	.vidioc_prepare_buf     = vb2_ioctl_prepare_buf,
+	.vidioc_querybuf	= vb2_ioctl_querybuf,
+	.vidioc_qbuf		= vb2_ioctl_qbuf,
+	.vidioc_dqbuf		= vb2_ioctl_dqbuf,
+	.vidioc_expbuf		= vb2_ioctl_expbuf,
+	.vidioc_streamon	= vb2_ioctl_streamon,
+	.vidioc_streamoff	= vb2_ioctl_streamoff,
+};
+
+/*
+ * Queue operations
+ */
+
+static int capture_queue_setup(struct vb2_queue *vq,
+			       unsigned int *nbuffers,
+			       unsigned int *nplanes,
+			       unsigned int sizes[],
+			       struct device *alloc_devs[])
+{
+	struct capture_priv *priv = vb2_get_drv_priv(vq);
+	struct v4l2_pix_format *pix = &priv->vdev.fmt.fmt.pix;
+	unsigned int count = *nbuffers;
+
+	if (vq->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+		return -EINVAL;
+
+	if (*nplanes) {
+		if (*nplanes != 1 || sizes[0] < pix->sizeimage)
+			return -EINVAL;
+		count += vq->num_buffers;
+	}
+
+	count = min_t(__u32, VID_MEM_LIMIT / pix->sizeimage, count);
+
+	if (*nplanes)
+		*nbuffers = (count < vq->num_buffers) ? 0 :
+			count - vq->num_buffers;
+	else
+		*nbuffers = count;
+
+	*nplanes = 1;
+	sizes[0] = pix->sizeimage;
+
+	return 0;
+}
+
+static int capture_buf_init(struct vb2_buffer *vb)
+{
+	struct imx_media_buffer *buf = to_imx_media_vb(vb);
+
+	INIT_LIST_HEAD(&buf->list);
+
+	return 0;
+}
+
+static int capture_buf_prepare(struct vb2_buffer *vb)
+{
+	struct vb2_queue *vq = vb->vb2_queue;
+	struct capture_priv *priv = vb2_get_drv_priv(vq);
+	struct v4l2_pix_format *pix = &priv->vdev.fmt.fmt.pix;
+
+	if (vb2_plane_size(vb, 0) < pix->sizeimage) {
+		v4l2_err(priv->src_sd,
+			 "data will not fit into plane (%lu < %lu)\n",
+			 vb2_plane_size(vb, 0), (long)pix->sizeimage);
+		return -EINVAL;
+	}
+
+	vb2_set_plane_payload(vb, 0, pix->sizeimage);
+
+	return 0;
+}
+
+static void capture_buf_queue(struct vb2_buffer *vb)
+{
+	struct capture_priv *priv = vb2_get_drv_priv(vb->vb2_queue);
+	struct imx_media_buffer *buf = to_imx_media_vb(vb);
+	unsigned long flags;
+
+	spin_lock_irqsave(&priv->q_lock, flags);
+
+	list_add_tail(&buf->list, &priv->ready_q);
+
+	spin_unlock_irqrestore(&priv->q_lock, flags);
+}
+
+static int capture_start_streaming(struct vb2_queue *vq, unsigned int count)
+{
+	struct capture_priv *priv = vb2_get_drv_priv(vq);
+	struct imx_media_buffer *buf, *tmp;
+	unsigned long flags;
+	int ret;
+
+	if (vb2_is_streaming(vq))
+		return 0;
+
+	ret = imx_media_pipeline_set_stream(priv->md, &priv->src_sd->entity,
+					    &priv->mp, true);
+	if (ret) {
+		v4l2_err(priv->src_sd, "pipeline start failed with %d\n", ret);
+		goto return_bufs;
+	}
+
+	priv->stop = false;
+
+	return 0;
+
+return_bufs:
+	spin_lock_irqsave(&priv->q_lock, flags);
+	list_for_each_entry_safe(buf, tmp, &priv->ready_q, list) {
+		list_del(&buf->list);
+		vb2_buffer_done(&buf->vbuf.vb2_buf, VB2_BUF_STATE_QUEUED);
+	}
+	spin_unlock_irqrestore(&priv->q_lock, flags);
+	return ret;
+}
+
+static void capture_stop_streaming(struct vb2_queue *vq)
+{
+	struct capture_priv *priv = vb2_get_drv_priv(vq);
+	struct imx_media_buffer *frame;
+	unsigned long flags;
+	int ret;
+
+	if (!vb2_is_streaming(vq))
+		return;
+
+	spin_lock_irqsave(&priv->q_lock, flags);
+	priv->stop = true;
+	spin_unlock_irqrestore(&priv->q_lock, flags);
+
+	ret = imx_media_pipeline_set_stream(priv->md, &priv->src_sd->entity,
+					    &priv->mp, false);
+	if (ret)
+		v4l2_warn(priv->src_sd, "pipeline stop failed with %d\n", ret);
+
+	/* release all active buffers */
+	spin_lock_irqsave(&priv->q_lock, flags);
+	while (!list_empty(&priv->ready_q)) {
+		frame = list_entry(priv->ready_q.next,
+				   struct imx_media_buffer, list);
+		list_del(&frame->list);
+		vb2_buffer_done(&frame->vbuf.vb2_buf, VB2_BUF_STATE_ERROR);
+	}
+	spin_unlock_irqrestore(&priv->q_lock, flags);
+}
+
+static struct vb2_ops capture_qops = {
+	.queue_setup	 = capture_queue_setup,
+	.buf_init        = capture_buf_init,
+	.buf_prepare	 = capture_buf_prepare,
+	.buf_queue	 = capture_buf_queue,
+	.wait_prepare	 = vb2_ops_wait_prepare,
+	.wait_finish	 = vb2_ops_wait_finish,
+	.start_streaming = capture_start_streaming,
+	.stop_streaming  = capture_stop_streaming,
+};
+
+/*
+ * File operations
+ */
+static int capture_open(struct file *file)
+{
+	struct capture_priv *priv = video_drvdata(file);
+	int ret;
+
+	if (mutex_lock_interruptible(&priv->mutex))
+		return -ERESTARTSYS;
+
+	ret = v4l2_fh_open(file);
+	if (ret)
+		v4l2_err(priv->src_sd, "v4l2_fh_open failed\n");
+
+	mutex_unlock(&priv->mutex);
+	return ret;
+}
+
+static int capture_release(struct file *file)
+{
+	struct capture_priv *priv = video_drvdata(file);
+	struct vb2_queue *vq = &priv->q;
+	int ret = 0;
+
+	mutex_lock(&priv->mutex);
+
+	if (file->private_data == vq->owner) {
+		vb2_queue_release(vq);
+		vq->owner = NULL;
+	}
+
+	v4l2_fh_release(file);
+	mutex_unlock(&priv->mutex);
+	return ret;
+}
+
+static const struct v4l2_file_operations capture_fops = {
+	.owner		= THIS_MODULE,
+	.open		= capture_open,
+	.release	= capture_release,
+	.poll		= vb2_fop_poll,
+	.unlocked_ioctl	= video_ioctl2,
+	.mmap		= vb2_fop_mmap,
+};
+
+static struct video_device capture_videodev = {
+	.fops		= &capture_fops,
+	.ioctl_ops	= &capture_ioctl_ops,
+	.minor		= -1,
+	.release	= video_device_release,
+	.vfl_dir	= VFL_DIR_RX,
+	.tvnorms	= V4L2_STD_NTSC | V4L2_STD_PAL | V4L2_STD_SECAM,
+	.device_caps	= V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING,
+};
+
+struct imx_media_buffer *
+imx_media_capture_device_next_buf(struct imx_media_video_dev *vdev)
+{
+	struct capture_priv *priv = to_capture_priv(vdev);
+	struct imx_media_buffer *buf = NULL;
+	unsigned long flags;
+
+	spin_lock_irqsave(&priv->q_lock, flags);
+
+	/* get next queued buffer */
+	if (!list_empty(&priv->ready_q)) {
+		buf = list_entry(priv->ready_q.next, struct imx_media_buffer,
+				 list);
+		list_del(&buf->list);
+	}
+
+	spin_unlock_irqrestore(&priv->q_lock, flags);
+
+	return buf;
+}
+EXPORT_SYMBOL_GPL(imx_media_capture_device_next_buf);
+
+void imx_media_capture_device_error(struct imx_media_video_dev *vdev)
+{
+	struct capture_priv *priv = to_capture_priv(vdev);
+	struct vb2_queue *vq = &priv->q;
+	unsigned long flags;
+
+	if (!vb2_is_streaming(vq))
+		return;
+
+	spin_lock_irqsave(&priv->q_lock, flags);
+	vb2_queue_error(vq);
+	spin_unlock_irqrestore(&priv->q_lock, flags);
+}
+EXPORT_SYMBOL_GPL(imx_media_capture_device_error);
+
+int imx_media_capture_device_register(struct imx_media_video_dev *vdev)
+{
+	struct capture_priv *priv = to_capture_priv(vdev);
+	struct v4l2_subdev *sd = priv->src_sd;
+	struct video_device *vfd = vdev->vfd;
+	struct vb2_queue *vq = &priv->q;
+	struct v4l2_subdev_format fmt_src;
+	int ret;
+
+	/* get media device */
+	priv->md = dev_get_drvdata(sd->v4l2_dev->dev);
+
+	vfd->v4l2_dev = sd->v4l2_dev;
+
+	ret = video_register_device(vfd, VFL_TYPE_GRABBER, -1);
+	if (ret) {
+		v4l2_err(sd, "Failed to register video device\n");
+		return ret;
+	}
+
+	vq->type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
+	vq->io_modes = VB2_MMAP | VB2_DMABUF;
+	vq->drv_priv = priv;
+	vq->buf_struct_size = sizeof(struct imx_media_buffer);
+	vq->ops = &capture_qops;
+	vq->mem_ops = &vb2_dma_contig_memops;
+	vq->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC;
+	vq->lock = &priv->mutex;
+	vq->min_buffers_needed = 2;
+	vq->dev = priv->dev;
+
+	ret = vb2_queue_init(vq);
+	if (ret) {
+		v4l2_err(sd, "vb2_queue_init failed\n");
+		goto unreg;
+	}
+
+	INIT_LIST_HEAD(&priv->ready_q);
+
+	priv->vdev_pad.flags = MEDIA_PAD_FL_SINK;
+	ret = media_entity_pads_init(&vfd->entity, 1, &priv->vdev_pad);
+	if (ret) {
+		v4l2_err(sd, "failed to init dev pad\n");
+		goto unreg;
+	}
+
+	/* create the link from the src_sd devnode pad to device node */
+	ret = media_create_pad_link(&sd->entity, priv->src_sd_pad,
+				    &vfd->entity, 0, 0);
+	if (ret) {
+		v4l2_err(sd, "failed to create link to device node\n");
+		goto unreg;
+	}
+
+	/* setup default format */
+	fmt_src.pad = priv->src_sd_pad;
+	fmt_src.which = V4L2_SUBDEV_FORMAT_ACTIVE;
+	v4l2_subdev_call(sd, pad, get_fmt, NULL, &fmt_src);
+	if (ret) {
+		v4l2_err(sd, "failed to get src_sd format\n");
+		goto unreg;
+	}
+
+	vdev->fmt.type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
+	imx_media_mbus_fmt_to_pix_fmt(&vdev->fmt.fmt.pix,
+				      &fmt_src.format, NULL);
+	vdev->cc = imx_media_find_format(0, fmt_src.format.code,
+					 true, false);
+
+	v4l2_info(sd, "Registered %s as /dev/%s\n", vfd->name,
+		  video_device_node_name(vfd));
+
+	vfd->ctrl_handler = &priv->ctrl_hdlr;
+
+	return 0;
+unreg:
+	video_unregister_device(vfd);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(imx_media_capture_device_register);
+
+void imx_media_capture_device_unregister(struct imx_media_video_dev *vdev)
+{
+	struct capture_priv *priv = to_capture_priv(vdev);
+	struct video_device *vfd = priv->vdev.vfd;
+
+	mutex_lock(&priv->mutex);
+
+	if (video_is_registered(vfd)) {
+		video_unregister_device(vfd);
+		media_entity_cleanup(&vfd->entity);
+	}
+
+	mutex_unlock(&priv->mutex);
+}
+EXPORT_SYMBOL_GPL(imx_media_capture_device_unregister);
+
+struct imx_media_video_dev *
+imx_media_capture_device_init(struct v4l2_subdev *src_sd, int pad)
+{
+	struct capture_priv *priv;
+	struct video_device *vfd;
+
+	priv = devm_kzalloc(src_sd->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return ERR_PTR(-ENOMEM);
+
+	priv->src_sd = src_sd;
+	priv->src_sd_pad = pad;
+	priv->dev = src_sd->dev;
+
+	mutex_init(&priv->mutex);
+	spin_lock_init(&priv->q_lock);
+
+	snprintf(capture_videodev.name, sizeof(capture_videodev.name),
+		 "%s capture", src_sd->name);
+
+	vfd = video_device_alloc();
+	if (!vfd)
+		return ERR_PTR(-ENOMEM);
+
+	*vfd = capture_videodev;
+	vfd->lock = &priv->mutex;
+	vfd->queue = &priv->q;
+	priv->vdev.vfd = vfd;
+
+	video_set_drvdata(vfd, priv);
+
+	v4l2_ctrl_handler_init(&priv->ctrl_hdlr, 0);
+
+	return &priv->vdev;
+}
+EXPORT_SYMBOL_GPL(imx_media_capture_device_init);
+
+void imx_media_capture_device_remove(struct imx_media_video_dev *vdev)
+{
+	struct capture_priv *priv = to_capture_priv(vdev);
+
+	v4l2_ctrl_handler_free(&priv->ctrl_hdlr);
+}
+EXPORT_SYMBOL_GPL(imx_media_capture_device_remove);
+
+MODULE_DESCRIPTION("i.MX5/6 v4l2 video capture interface driver");
+MODULE_AUTHOR("Steve Longerbeam <steve_longerbeam@mentor.com>");
+MODULE_LICENSE("GPL");
-- 
2.7.4

[PATCH v5 24/39] media: imx: Add Capture Device Interface

[Steve Longerbeam]

This is the capture device interface driver that provides the v4l2
user interface. Frames can be received from various sources:

- directly from CSI for capturing unconverted images directly from
  camera sensors.

- from the IC pre-process encode task.

- from the IC pre-process viewfinder task.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/Makefile            |   1 +
 drivers/staging/media/imx/imx-media-capture.c | 655 ++++++++++++++++++++++++++
 2 files changed, 656 insertions(+)
 create mode 100644 drivers/staging/media/imx/imx-media-capture.c

diff --git a/drivers/staging/media/imx/Makefile b/drivers/staging/media/imx/Makefile
index ddd7d94..4606a3a 100644
--- a/drivers/staging/media/imx/Makefile
+++ b/drivers/staging/media/imx/Makefile
@@ -3,3 +3,4 @@ imx-media-common-objs := imx-media-utils.o imx-media-fim.o
 
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-common.o
+obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-capture.o
diff --git a/drivers/staging/media/imx/imx-media-capture.c b/drivers/staging/media/imx/imx-media-capture.c
new file mode 100644
index 0000000..704ed85
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media-capture.c
@@ -0,0 +1,655 @@
+/*
+ * Video Capture Subdev for Freescale i.MX5/6 SOC
+ *
+ * Copyright (c) 2012-2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/delay.h>
+#include <linux/fs.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/platform_device.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/timer.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-ioctl.h>
+#include <media/v4l2-of.h>
+#include <media/v4l2-mc.h>
+#include <media/v4l2-subdev.h>
+#include <media/videobuf2-dma-contig.h>
+#include <video/imx-ipu-v3.h>
+#include <media/imx.h>
+#include "imx-media.h"
+
+struct capture_priv {
+	struct imx_media_video_dev vdev;
+
+	struct v4l2_subdev    *src_sd;
+	int                   src_sd_pad;
+	struct device         *dev;
+
+	struct media_pipeline mp;
+	struct imx_media_dev  *md;
+
+	struct media_pad      vdev_pad;
+
+	struct mutex          mutex;       /* capture device mutex */
+
+	/* the videobuf2 queue */
+	struct vb2_queue       q;
+	/* list of ready imx_media_buffer's from q */
+	struct list_head       ready_q;
+	/* protect ready_q */
+	spinlock_t             q_lock;
+
+	/* controls inherited from subdevs */
+	struct v4l2_ctrl_handler ctrl_hdlr;
+
+	/* misc status */
+	bool                  stop;          /* streaming is stopping */
+};
+
+#define to_capture_priv(v) container_of(v, struct capture_priv, vdev)
+
+/* In bytes, per queue */
+#define VID_MEM_LIMIT	SZ_64M
+
+static struct vb2_ops capture_qops;
+
+/*
+ * Video ioctls follow
+ */
+
+static int vidioc_querycap(struct file *file, void *fh,
+			   struct v4l2_capability *cap)
+{
+	struct capture_priv *priv = video_drvdata(file);
+
+	strncpy(cap->driver, "imx-media-capture", sizeof(cap->driver) - 1);
+	strncpy(cap->card, "imx-media-capture", sizeof(cap->card) - 1);
+	snprintf(cap->bus_info, sizeof(cap->bus_info),
+		 "platform:%s", dev_name(priv->dev));
+
+	return 0;
+}
+
+static int capture_enum_fmt_vid_cap(struct file *file, void *fh,
+				    struct v4l2_fmtdesc *f)
+{
+	u32 fourcc;
+	int ret;
+
+	ret = imx_media_enum_format(&fourcc, NULL, f->index, true, true);
+	if (ret)
+		return ret;
+
+	f->pixelformat = fourcc;
+
+	return 0;
+}
+
+static int capture_g_fmt_vid_cap(struct file *file, void *fh,
+				 struct v4l2_format *f)
+{
+	struct capture_priv *priv = video_drvdata(file);
+
+	*f = priv->vdev.fmt;
+
+	return 0;
+}
+
+static int capture_try_fmt_vid_cap(struct file *file, void *fh,
+				   struct v4l2_format *f)
+{
+	struct capture_priv *priv = video_drvdata(file);
+	struct v4l2_subdev_format fmt_src;
+	const struct imx_media_pixfmt *cc, *src_cc;
+	u32 fourcc;
+	int ret;
+
+	fourcc = f->fmt.pix.pixelformat;
+	cc = imx_media_find_format(fourcc, 0, true, true);
+	if (!cc) {
+		imx_media_enum_format(&fourcc, NULL, 0, true, true);
+		cc = imx_media_find_format(fourcc, 0, true, true);
+	}
+
+	/*
+	 * user frame dimensions are the same as src_sd's pad.
+	 */
+	fmt_src.pad = priv->src_sd_pad;
+	fmt_src.which = V4L2_SUBDEV_FORMAT_ACTIVE;
+	ret = v4l2_subdev_call(priv->src_sd, pad, get_fmt, NULL, &fmt_src);
+	if (ret)
+		return ret;
+
+	/*
+	 * but we can allow planar pixel formats if the src_sd's
+	 * pad configured a YUV format
+	 */
+	src_cc = imx_media_find_format(0, fmt_src.format.code, true, false);
+	if (src_cc->cs == IPUV3_COLORSPACE_YUV &&
+	    cc->cs == IPUV3_COLORSPACE_YUV) {
+		imx_media_mbus_fmt_to_pix_fmt(&f->fmt.pix,
+					      &fmt_src.format, cc);
+	} else {
+		imx_media_mbus_fmt_to_pix_fmt(&f->fmt.pix,
+					      &fmt_src.format, src_cc);
+	}
+
+	return 0;
+}
+
+static int capture_s_fmt_vid_cap(struct file *file, void *fh,
+				 struct v4l2_format *f)
+{
+	struct capture_priv *priv = video_drvdata(file);
+	int ret;
+
+	if (vb2_is_busy(&priv->q)) {
+		v4l2_err(priv->src_sd, "%s queue busy\n", __func__);
+		return -EBUSY;
+	}
+
+	ret = capture_try_fmt_vid_cap(file, priv, f);
+	if (ret)
+		return ret;
+
+	priv->vdev.fmt.fmt.pix = f->fmt.pix;
+	priv->vdev.cc = imx_media_find_format(f->fmt.pix.pixelformat, 0,
+					      true, true);
+
+	return 0;
+}
+
+static int capture_querystd(struct file *file, void *fh, v4l2_std_id *std)
+{
+	struct capture_priv *priv = video_drvdata(file);
+
+	return v4l2_subdev_call(priv->src_sd, video, querystd, std);
+}
+
+static int capture_g_std(struct file *file, void *fh, v4l2_std_id *std)
+{
+	struct capture_priv *priv = video_drvdata(file);
+
+	return v4l2_subdev_call(priv->src_sd, video, g_std, std);
+}
+
+static int capture_s_std(struct file *file, void *fh, v4l2_std_id std)
+{
+	struct capture_priv *priv = video_drvdata(file);
+
+	if (vb2_is_busy(&priv->q))
+		return -EBUSY;
+
+	return v4l2_subdev_call(priv->src_sd, video, s_std, std);
+}
+
+static int capture_g_parm(struct file *file, void *fh,
+			  struct v4l2_streamparm *a)
+{
+	struct capture_priv *priv = video_drvdata(file);
+	struct v4l2_subdev_frame_interval fi;
+	int ret;
+
+	if (a->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+		return -EINVAL;
+
+	memset(&fi, 0, sizeof(fi));
+	fi.pad = priv->src_sd_pad;
+	ret = v4l2_subdev_call(priv->src_sd, video, g_frame_interval, &fi);
+	if (ret < 0)
+		return ret;
+
+	a->parm.capture.capability = V4L2_CAP_TIMEPERFRAME;
+	a->parm.capture.timeperframe = fi.interval;
+
+	return 0;
+}
+
+static int capture_s_parm(struct file *file, void *fh,
+			  struct v4l2_streamparm *a)
+{
+	struct capture_priv *priv = video_drvdata(file);
+	struct v4l2_subdev_frame_interval fi;
+	int ret;
+
+	if (a->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+		return -EINVAL;
+
+	memset(&fi, 0, sizeof(fi));
+	fi.pad = priv->src_sd_pad;
+	fi.interval = a->parm.capture.timeperframe;
+	ret = v4l2_subdev_call(priv->src_sd, video, s_frame_interval, &fi);
+	if (ret < 0)
+		return ret;
+
+	a->parm.capture.capability = V4L2_CAP_TIMEPERFRAME;
+	a->parm.capture.timeperframe = fi.interval;
+
+	return 0;
+}
+
+static const struct v4l2_ioctl_ops capture_ioctl_ops = {
+	.vidioc_querycap	= vidioc_querycap,
+
+	.vidioc_enum_fmt_vid_cap        = capture_enum_fmt_vid_cap,
+	.vidioc_g_fmt_vid_cap           = capture_g_fmt_vid_cap,
+	.vidioc_try_fmt_vid_cap         = capture_try_fmt_vid_cap,
+	.vidioc_s_fmt_vid_cap           = capture_s_fmt_vid_cap,
+
+	.vidioc_querystd        = capture_querystd,
+	.vidioc_g_std           = capture_g_std,
+	.vidioc_s_std           = capture_s_std,
+
+	.vidioc_g_parm          = capture_g_parm,
+	.vidioc_s_parm          = capture_s_parm,
+
+	.vidioc_reqbufs		= vb2_ioctl_reqbufs,
+	.vidioc_create_bufs     = vb2_ioctl_create_bufs,
+	.vidioc_prepare_buf     = vb2_ioctl_prepare_buf,
+	.vidioc_querybuf	= vb2_ioctl_querybuf,
+	.vidioc_qbuf		= vb2_ioctl_qbuf,
+	.vidioc_dqbuf		= vb2_ioctl_dqbuf,
+	.vidioc_expbuf		= vb2_ioctl_expbuf,
+	.vidioc_streamon	= vb2_ioctl_streamon,
+	.vidioc_streamoff	= vb2_ioctl_streamoff,
+};
+
+/*
+ * Queue operations
+ */
+
+static int capture_queue_setup(struct vb2_queue *vq,
+			       unsigned int *nbuffers,
+			       unsigned int *nplanes,
+			       unsigned int sizes[],
+			       struct device *alloc_devs[])
+{
+	struct capture_priv *priv = vb2_get_drv_priv(vq);
+	struct v4l2_pix_format *pix = &priv->vdev.fmt.fmt.pix;
+	unsigned int count = *nbuffers;
+
+	if (vq->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+		return -EINVAL;
+
+	if (*nplanes) {
+		if (*nplanes != 1 || sizes[0] < pix->sizeimage)
+			return -EINVAL;
+		count += vq->num_buffers;
+	}
+
+	count = min_t(__u32, VID_MEM_LIMIT / pix->sizeimage, count);
+
+	if (*nplanes)
+		*nbuffers = (count < vq->num_buffers) ? 0 :
+			count - vq->num_buffers;
+	else
+		*nbuffers = count;
+
+	*nplanes = 1;
+	sizes[0] = pix->sizeimage;
+
+	return 0;
+}
+
+static int capture_buf_init(struct vb2_buffer *vb)
+{
+	struct imx_media_buffer *buf = to_imx_media_vb(vb);
+
+	INIT_LIST_HEAD(&buf->list);
+
+	return 0;
+}
+
+static int capture_buf_prepare(struct vb2_buffer *vb)
+{
+	struct vb2_queue *vq = vb->vb2_queue;
+	struct capture_priv *priv = vb2_get_drv_priv(vq);
+	struct v4l2_pix_format *pix = &priv->vdev.fmt.fmt.pix;
+
+	if (vb2_plane_size(vb, 0) < pix->sizeimage) {
+		v4l2_err(priv->src_sd,
+			 "data will not fit into plane (%lu < %lu)\n",
+			 vb2_plane_size(vb, 0), (long)pix->sizeimage);
+		return -EINVAL;
+	}
+
+	vb2_set_plane_payload(vb, 0, pix->sizeimage);
+
+	return 0;
+}
+
+static void capture_buf_queue(struct vb2_buffer *vb)
+{
+	struct capture_priv *priv = vb2_get_drv_priv(vb->vb2_queue);
+	struct imx_media_buffer *buf = to_imx_media_vb(vb);
+	unsigned long flags;
+
+	spin_lock_irqsave(&priv->q_lock, flags);
+
+	list_add_tail(&buf->list, &priv->ready_q);
+
+	spin_unlock_irqrestore(&priv->q_lock, flags);
+}
+
+static int capture_start_streaming(struct vb2_queue *vq, unsigned int count)
+{
+	struct capture_priv *priv = vb2_get_drv_priv(vq);
+	struct imx_media_buffer *buf, *tmp;
+	unsigned long flags;
+	int ret;
+
+	if (vb2_is_streaming(vq))
+		return 0;
+
+	ret = imx_media_pipeline_set_stream(priv->md, &priv->src_sd->entity,
+					    &priv->mp, true);
+	if (ret) {
+		v4l2_err(priv->src_sd, "pipeline start failed with %d\n", ret);
+		goto return_bufs;
+	}
+
+	priv->stop = false;
+
+	return 0;
+
+return_bufs:
+	spin_lock_irqsave(&priv->q_lock, flags);
+	list_for_each_entry_safe(buf, tmp, &priv->ready_q, list) {
+		list_del(&buf->list);
+		vb2_buffer_done(&buf->vbuf.vb2_buf, VB2_BUF_STATE_QUEUED);
+	}
+	spin_unlock_irqrestore(&priv->q_lock, flags);
+	return ret;
+}
+
+static void capture_stop_streaming(struct vb2_queue *vq)
+{
+	struct capture_priv *priv = vb2_get_drv_priv(vq);
+	struct imx_media_buffer *frame;
+	unsigned long flags;
+	int ret;
+
+	if (!vb2_is_streaming(vq))
+		return;
+
+	spin_lock_irqsave(&priv->q_lock, flags);
+	priv->stop = true;
+	spin_unlock_irqrestore(&priv->q_lock, flags);
+
+	ret = imx_media_pipeline_set_stream(priv->md, &priv->src_sd->entity,
+					    &priv->mp, false);
+	if (ret)
+		v4l2_warn(priv->src_sd, "pipeline stop failed with %d\n", ret);
+
+	/* release all active buffers */
+	spin_lock_irqsave(&priv->q_lock, flags);
+	while (!list_empty(&priv->ready_q)) {
+		frame = list_entry(priv->ready_q.next,
+				   struct imx_media_buffer, list);
+		list_del(&frame->list);
+		vb2_buffer_done(&frame->vbuf.vb2_buf, VB2_BUF_STATE_ERROR);
+	}
+	spin_unlock_irqrestore(&priv->q_lock, flags);
+}
+
+static struct vb2_ops capture_qops = {
+	.queue_setup	 = capture_queue_setup,
+	.buf_init        = capture_buf_init,
+	.buf_prepare	 = capture_buf_prepare,
+	.buf_queue	 = capture_buf_queue,
+	.wait_prepare	 = vb2_ops_wait_prepare,
+	.wait_finish	 = vb2_ops_wait_finish,
+	.start_streaming = capture_start_streaming,
+	.stop_streaming  = capture_stop_streaming,
+};
+
+/*
+ * File operations
+ */
+static int capture_open(struct file *file)
+{
+	struct capture_priv *priv = video_drvdata(file);
+	int ret;
+
+	if (mutex_lock_interruptible(&priv->mutex))
+		return -ERESTARTSYS;
+
+	ret = v4l2_fh_open(file);
+	if (ret)
+		v4l2_err(priv->src_sd, "v4l2_fh_open failed\n");
+
+	mutex_unlock(&priv->mutex);
+	return ret;
+}
+
+static int capture_release(struct file *file)
+{
+	struct capture_priv *priv = video_drvdata(file);
+	struct vb2_queue *vq = &priv->q;
+	int ret = 0;
+
+	mutex_lock(&priv->mutex);
+
+	if (file->private_data == vq->owner) {
+		vb2_queue_release(vq);
+		vq->owner = NULL;
+	}
+
+	v4l2_fh_release(file);
+	mutex_unlock(&priv->mutex);
+	return ret;
+}
+
+static const struct v4l2_file_operations capture_fops = {
+	.owner		= THIS_MODULE,
+	.open		= capture_open,
+	.release	= capture_release,
+	.poll		= vb2_fop_poll,
+	.unlocked_ioctl	= video_ioctl2,
+	.mmap		= vb2_fop_mmap,
+};
+
+static struct video_device capture_videodev = {
+	.fops		= &capture_fops,
+	.ioctl_ops	= &capture_ioctl_ops,
+	.minor		= -1,
+	.release	= video_device_release,
+	.vfl_dir	= VFL_DIR_RX,
+	.tvnorms	= V4L2_STD_NTSC | V4L2_STD_PAL | V4L2_STD_SECAM,
+	.device_caps	= V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING,
+};
+
+struct imx_media_buffer *
+imx_media_capture_device_next_buf(struct imx_media_video_dev *vdev)
+{
+	struct capture_priv *priv = to_capture_priv(vdev);
+	struct imx_media_buffer *buf = NULL;
+	unsigned long flags;
+
+	spin_lock_irqsave(&priv->q_lock, flags);
+
+	/* get next queued buffer */
+	if (!list_empty(&priv->ready_q)) {
+		buf = list_entry(priv->ready_q.next, struct imx_media_buffer,
+				 list);
+		list_del(&buf->list);
+	}
+
+	spin_unlock_irqrestore(&priv->q_lock, flags);
+
+	return buf;
+}
+EXPORT_SYMBOL_GPL(imx_media_capture_device_next_buf);
+
+void imx_media_capture_device_error(struct imx_media_video_dev *vdev)
+{
+	struct capture_priv *priv = to_capture_priv(vdev);
+	struct vb2_queue *vq = &priv->q;
+	unsigned long flags;
+
+	if (!vb2_is_streaming(vq))
+		return;
+
+	spin_lock_irqsave(&priv->q_lock, flags);
+	vb2_queue_error(vq);
+	spin_unlock_irqrestore(&priv->q_lock, flags);
+}
+EXPORT_SYMBOL_GPL(imx_media_capture_device_error);
+
+int imx_media_capture_device_register(struct imx_media_video_dev *vdev)
+{
+	struct capture_priv *priv = to_capture_priv(vdev);
+	struct v4l2_subdev *sd = priv->src_sd;
+	struct video_device *vfd = vdev->vfd;
+	struct vb2_queue *vq = &priv->q;
+	struct v4l2_subdev_format fmt_src;
+	int ret;
+
+	/* get media device */
+	priv->md = dev_get_drvdata(sd->v4l2_dev->dev);
+
+	vfd->v4l2_dev = sd->v4l2_dev;
+
+	ret = video_register_device(vfd, VFL_TYPE_GRABBER, -1);
+	if (ret) {
+		v4l2_err(sd, "Failed to register video device\n");
+		return ret;
+	}
+
+	vq->type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
+	vq->io_modes = VB2_MMAP | VB2_DMABUF;
+	vq->drv_priv = priv;
+	vq->buf_struct_size = sizeof(struct imx_media_buffer);
+	vq->ops = &capture_qops;
+	vq->mem_ops = &vb2_dma_contig_memops;
+	vq->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC;
+	vq->lock = &priv->mutex;
+	vq->min_buffers_needed = 2;
+	vq->dev = priv->dev;
+
+	ret = vb2_queue_init(vq);
+	if (ret) {
+		v4l2_err(sd, "vb2_queue_init failed\n");
+		goto unreg;
+	}
+
+	INIT_LIST_HEAD(&priv->ready_q);
+
+	priv->vdev_pad.flags = MEDIA_PAD_FL_SINK;
+	ret = media_entity_pads_init(&vfd->entity, 1, &priv->vdev_pad);
+	if (ret) {
+		v4l2_err(sd, "failed to init dev pad\n");
+		goto unreg;
+	}
+
+	/* create the link from the src_sd devnode pad to device node */
+	ret = media_create_pad_link(&sd->entity, priv->src_sd_pad,
+				    &vfd->entity, 0, 0);
+	if (ret) {
+		v4l2_err(sd, "failed to create link to device node\n");
+		goto unreg;
+	}
+
+	/* setup default format */
+	fmt_src.pad = priv->src_sd_pad;
+	fmt_src.which = V4L2_SUBDEV_FORMAT_ACTIVE;
+	v4l2_subdev_call(sd, pad, get_fmt, NULL, &fmt_src);
+	if (ret) {
+		v4l2_err(sd, "failed to get src_sd format\n");
+		goto unreg;
+	}
+
+	vdev->fmt.type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
+	imx_media_mbus_fmt_to_pix_fmt(&vdev->fmt.fmt.pix,
+				      &fmt_src.format, NULL);
+	vdev->cc = imx_media_find_format(0, fmt_src.format.code,
+					 true, false);
+
+	v4l2_info(sd, "Registered %s as /dev/%s\n", vfd->name,
+		  video_device_node_name(vfd));
+
+	vfd->ctrl_handler = &priv->ctrl_hdlr;
+
+	return 0;
+unreg:
+	video_unregister_device(vfd);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(imx_media_capture_device_register);
+
+void imx_media_capture_device_unregister(struct imx_media_video_dev *vdev)
+{
+	struct capture_priv *priv = to_capture_priv(vdev);
+	struct video_device *vfd = priv->vdev.vfd;
+
+	mutex_lock(&priv->mutex);
+
+	if (video_is_registered(vfd)) {
+		video_unregister_device(vfd);
+		media_entity_cleanup(&vfd->entity);
+	}
+
+	mutex_unlock(&priv->mutex);
+}
+EXPORT_SYMBOL_GPL(imx_media_capture_device_unregister);
+
+struct imx_media_video_dev *
+imx_media_capture_device_init(struct v4l2_subdev *src_sd, int pad)
+{
+	struct capture_priv *priv;
+	struct video_device *vfd;
+
+	priv = devm_kzalloc(src_sd->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return ERR_PTR(-ENOMEM);
+
+	priv->src_sd = src_sd;
+	priv->src_sd_pad = pad;
+	priv->dev = src_sd->dev;
+
+	mutex_init(&priv->mutex);
+	spin_lock_init(&priv->q_lock);
+
+	snprintf(capture_videodev.name, sizeof(capture_videodev.name),
+		 "%s capture", src_sd->name);
+
+	vfd = video_device_alloc();
+	if (!vfd)
+		return ERR_PTR(-ENOMEM);
+
+	*vfd = capture_videodev;
+	vfd->lock = &priv->mutex;
+	vfd->queue = &priv->q;
+	priv->vdev.vfd = vfd;
+
+	video_set_drvdata(vfd, priv);
+
+	v4l2_ctrl_handler_init(&priv->ctrl_hdlr, 0);
+
+	return &priv->vdev;
+}
+EXPORT_SYMBOL_GPL(imx_media_capture_device_init);
+
+void imx_media_capture_device_remove(struct imx_media_video_dev *vdev)
+{
+	struct capture_priv *priv = to_capture_priv(vdev);
+
+	v4l2_ctrl_handler_free(&priv->ctrl_hdlr);
+}
+EXPORT_SYMBOL_GPL(imx_media_capture_device_remove);
+
+MODULE_DESCRIPTION("i.MX5/6 v4l2 video capture interface driver");
+MODULE_AUTHOR("Steve Longerbeam <steve_longerbeam@mentor.com>");
+MODULE_LICENSE("GPL");
-- 
2.7.4

[PATCH v5 25/39] media: imx: Add CSI subdev driver

[Steve Longerbeam]

This is a media entity subdevice for the i.MX Camera
Sensor Interface module.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/Kconfig         |   14 +
 drivers/staging/media/imx/Makefile        |    2 +
 drivers/staging/media/imx/imx-media-csi.c | 1311 +++++++++++++++++++++++++++++
 3 files changed, 1327 insertions(+)
 create mode 100644 drivers/staging/media/imx/imx-media-csi.c

diff --git a/drivers/staging/media/imx/Kconfig b/drivers/staging/media/imx/Kconfig
index 62a3c34..e27ad6d 100644
--- a/drivers/staging/media/imx/Kconfig
+++ b/drivers/staging/media/imx/Kconfig
@@ -4,3 +4,17 @@ config VIDEO_IMX_MEDIA
 	---help---
 	  Say yes here to enable support for video4linux media controller
 	  driver for the i.MX5/6 SOC.
+
+if VIDEO_IMX_MEDIA
+menu "i.MX5/6 Media Sub devices"
+
+config VIDEO_IMX_CSI
+	tristate "i.MX5/6 Camera Sensor Interface driver"
+	depends on VIDEO_IMX_MEDIA && VIDEO_DEV && I2C
+	select VIDEOBUF2_DMA_CONTIG
+	default y
+	---help---
+	  A video4linux camera sensor interface driver for i.MX5/6.
+
+endmenu
+endif
diff --git a/drivers/staging/media/imx/Makefile b/drivers/staging/media/imx/Makefile
index 4606a3a..c054490 100644
--- a/drivers/staging/media/imx/Makefile
+++ b/drivers/staging/media/imx/Makefile
@@ -4,3 +4,5 @@ imx-media-common-objs := imx-media-utils.o imx-media-fim.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-common.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-capture.o
+
+obj-$(CONFIG_VIDEO_IMX_CSI) += imx-media-csi.o
diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
new file mode 100644
index 0000000..ab78ff7
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -0,0 +1,1311 @@
+/*
+ * V4L2 Capture CSI Subdev for Freescale i.MX5/6 SOC
+ *
+ * Copyright (c) 2014-2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-mc.h>
+#include <media/v4l2-of.h>
+#include <media/v4l2-subdev.h>
+#include <media/videobuf2-dma-contig.h>
+#include <video/imx-ipu-v3.h>
+#include <media/imx.h>
+#include "imx-media.h"
+
+/*
+ * Min/Max supported width and heights.
+ *
+ * We allow planar output, so we have to align width by 16 pixels
+ * to meet IDMAC alignment requirements.
+ *
+ * TODO: move this into pad format negotiation, if capture device
+ * has not requested planar formats, we should allow 8 pixel
+ * alignment.
+ */
+#define MIN_W       176
+#define MIN_H       144
+#define MAX_W      4096
+#define MAX_H      4096
+#define W_ALIGN    4 /* multiple of 16 pixels */
+#define H_ALIGN    1 /* multiple of 2 lines */
+#define S_ALIGN    1 /* multiple of 2 */
+
+struct csi_priv {
+	struct device *dev;
+	struct ipu_soc *ipu;
+	struct imx_media_dev *md;
+	struct v4l2_subdev sd;
+	struct media_pad pad[CSI_NUM_PADS];
+	/* the video device at IDMAC output pad */
+	struct imx_media_video_dev *vdev;
+	struct imx_media_fim *fim;
+	int csi_id;
+	int smfc_id;
+
+	/* lock to protect all members below */
+	struct mutex lock;
+
+	int active_output_pad;
+
+	struct ipuv3_channel *idmac_ch;
+	struct ipu_smfc *smfc;
+	struct ipu_csi *csi;
+
+	struct v4l2_mbus_framefmt format_mbus[CSI_NUM_PADS];
+	const struct imx_media_pixfmt *cc[CSI_NUM_PADS];
+	struct v4l2_rect crop;
+
+	/* active vb2 buffers to send to video dev sink */
+	struct imx_media_buffer *active_vb2_buf[2];
+	struct imx_media_dma_buf underrun_buf;
+
+	int ipu_buf_num;  /* ipu double buffer index: 0-1 */
+
+	/* the sink for the captured frames */
+	struct media_entity *sink;
+	enum ipu_csi_dest dest;
+	/* the source subdev */
+	struct v4l2_subdev *src_sd;
+
+	/* the mipi virtual channel number at link validate */
+	int vc_num;
+
+	/* the attached sensor at stream on */
+	struct imx_media_subdev *sensor;
+
+	spinlock_t irqlock; /* protect eof_irq handler */
+	struct timer_list eof_timeout_timer;
+	int eof_irq;
+	int nfb4eof_irq;
+
+	struct v4l2_ctrl_handler ctrl_hdlr;
+
+	int power_count; /* power counter */
+	bool stream_on;  /* streaming is on */
+	bool last_eof;   /* waiting for last EOF at stream off */
+	struct completion last_eof_comp;
+};
+
+static inline struct csi_priv *sd_to_dev(struct v4l2_subdev *sdev)
+{
+	return container_of(sdev, struct csi_priv, sd);
+}
+
+static void csi_idmac_put_ipu_resources(struct csi_priv *priv)
+{
+	if (!IS_ERR_OR_NULL(priv->idmac_ch))
+		ipu_idmac_put(priv->idmac_ch);
+	priv->idmac_ch = NULL;
+
+	if (!IS_ERR_OR_NULL(priv->smfc))
+		ipu_smfc_put(priv->smfc);
+	priv->smfc = NULL;
+}
+
+static int csi_idmac_get_ipu_resources(struct csi_priv *priv)
+{
+	int ch_num, ret;
+
+	ch_num = IPUV3_CHANNEL_CSI0 + priv->smfc_id;
+
+	priv->smfc = ipu_smfc_get(priv->ipu, ch_num);
+	if (IS_ERR(priv->smfc)) {
+		v4l2_err(&priv->sd, "failed to get SMFC\n");
+		ret = PTR_ERR(priv->smfc);
+		goto out;
+	}
+
+	priv->idmac_ch = ipu_idmac_get(priv->ipu, ch_num);
+	if (IS_ERR(priv->idmac_ch)) {
+		v4l2_err(&priv->sd, "could not get IDMAC channel %u\n",
+			 ch_num);
+		ret = PTR_ERR(priv->idmac_ch);
+		goto out;
+	}
+
+	return 0;
+out:
+	csi_idmac_put_ipu_resources(priv);
+	return ret;
+}
+
+static void csi_vb2_buf_done(struct csi_priv *priv)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct imx_media_buffer *done, *next;
+	struct vb2_buffer *vb;
+	dma_addr_t phys;
+
+	done = priv->active_vb2_buf[priv->ipu_buf_num];
+	if (done) {
+		vb = &done->vbuf.vb2_buf;
+		vb->timestamp = ktime_get_ns();
+		vb2_buffer_done(vb, VB2_BUF_STATE_DONE);
+	}
+
+	/* get next queued buffer */
+	next = imx_media_capture_device_next_buf(vdev);
+	if (next) {
+		phys = vb2_dma_contig_plane_dma_addr(&next->vbuf.vb2_buf, 0);
+		priv->active_vb2_buf[priv->ipu_buf_num] = next;
+	} else {
+		phys = priv->underrun_buf.phys;
+		priv->active_vb2_buf[priv->ipu_buf_num] = NULL;
+	}
+
+	if (ipu_idmac_buffer_is_ready(priv->idmac_ch, priv->ipu_buf_num))
+		ipu_idmac_clear_buffer(priv->idmac_ch, priv->ipu_buf_num);
+
+	ipu_cpmem_set_buffer(priv->idmac_ch, priv->ipu_buf_num, phys);
+}
+
+static void csi_call_fim(struct csi_priv *priv)
+{
+	if (priv->fim) {
+		struct timespec cur_ts;
+
+		ktime_get_ts(&cur_ts);
+		/* call frame interval monitor */
+		imx_media_fim_eof_monitor(priv->fim, &cur_ts);
+	}
+}
+
+static irqreturn_t csi_idmac_eof_interrupt(int irq, void *dev_id)
+{
+	struct csi_priv *priv = dev_id;
+
+	spin_lock(&priv->irqlock);
+
+	if (priv->last_eof) {
+		complete(&priv->last_eof_comp);
+		priv->last_eof = false;
+		goto unlock;
+	}
+
+	csi_call_fim(priv);
+
+	csi_vb2_buf_done(priv);
+
+	/* select new IPU buf */
+	ipu_idmac_select_buffer(priv->idmac_ch, priv->ipu_buf_num);
+	/* toggle IPU double-buffer index */
+	priv->ipu_buf_num ^= 1;
+
+	/* bump the EOF timeout timer */
+	mod_timer(&priv->eof_timeout_timer,
+		  jiffies + msecs_to_jiffies(IMX_MEDIA_EOF_TIMEOUT));
+
+unlock:
+	spin_unlock(&priv->irqlock);
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t csi_idmac_nfb4eof_interrupt(int irq, void *dev_id)
+{
+	struct csi_priv *priv = dev_id;
+	static const struct v4l2_event ev = {
+		.type = V4L2_EVENT_NEW_FRAME_BEFORE_EOF,
+	};
+
+	v4l2_err(&priv->sd, "NFB4EOF\n");
+
+	v4l2_subdev_notify_event(&priv->sd, &ev);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * EOF timeout timer function. This is an unrecoverable condition
+ * without a stream restart.
+ */
+static void csi_idmac_eof_timeout(unsigned long data)
+{
+	struct csi_priv *priv = (struct csi_priv *)data;
+	struct imx_media_video_dev *vdev = priv->vdev;
+
+	v4l2_err(&priv->sd, "EOF timeout\n");
+
+	/* signal a fatal error to capture device */
+	imx_media_capture_device_error(vdev);
+}
+
+static void csi_idmac_setup_vb2_buf(struct csi_priv *priv, dma_addr_t *phys)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct imx_media_buffer *buf;
+	int i;
+
+	for (i = 0; i < 2; i++) {
+		buf = imx_media_capture_device_next_buf(vdev);
+		priv->active_vb2_buf[i] = buf;
+		phys[i] = vb2_dma_contig_plane_dma_addr(&buf->vbuf.vb2_buf, 0);
+	}
+}
+
+static void csi_idmac_unsetup_vb2_buf(struct csi_priv *priv,
+				      enum vb2_buffer_state return_state)
+{
+	struct imx_media_buffer *buf;
+	int i;
+
+	/* return any remaining active frames with error */
+	for (i = 0; i < 2; i++) {
+		buf = priv->active_vb2_buf[i];
+		if (buf) {
+			struct vb2_buffer *vb = &buf->vbuf.vb2_buf;
+
+			vb->timestamp = ktime_get_ns();
+			vb2_buffer_done(vb, return_state);
+		}
+	}
+}
+
+/* init the SMFC IDMAC channel */
+static int csi_idmac_setup_channel(struct csi_priv *priv)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct v4l2_of_endpoint *sensor_ep;
+	struct v4l2_mbus_framefmt *infmt;
+	unsigned int burst_size;
+	struct ipu_image image;
+	dma_addr_t phys[2];
+	bool passthrough;
+	int ret;
+
+	infmt = &priv->format_mbus[CSI_SINK_PAD];
+	sensor_ep = &priv->sensor->sensor_ep;
+
+	ipu_cpmem_zero(priv->idmac_ch);
+
+	memset(&image, 0, sizeof(image));
+	image.pix = vdev->fmt.fmt.pix;
+	image.rect.width = image.pix.width;
+	image.rect.height = image.pix.height;
+
+	csi_idmac_setup_vb2_buf(priv, phys);
+
+	image.phys0 = phys[0];
+	image.phys1 = phys[1];
+
+	ret = ipu_cpmem_set_image(priv->idmac_ch, &image);
+	if (ret)
+		return ret;
+
+	burst_size = (image.pix.width & 0xf) ? 8 : 16;
+
+	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
+
+	/*
+	 * If the sensor uses 16-bit parallel CSI bus, we must handle
+	 * the data internally in the IPU as 16-bit generic, aka
+	 * passthrough mode.
+	 */
+	passthrough = (sensor_ep->bus_type != V4L2_MBUS_CSI2 &&
+		       sensor_ep->bus.parallel.bus_width >= 16);
+
+	if (passthrough)
+		ipu_cpmem_set_format_passthrough(priv->idmac_ch, 16);
+
+	/*
+	 * Set the channel for the direct CSI-->memory via SMFC
+	 * use-case to very high priority, by enabling the watermark
+	 * signal in the SMFC, enabling WM in the channel, and setting
+	 * the channel priority to high.
+	 *
+	 * Refer to the i.mx6 rev. D TRM Table 36-8: Calculated priority
+	 * value.
+	 *
+	 * The WM's are set very low by intention here to ensure that
+	 * the SMFC FIFOs do not overflow.
+	 */
+	ipu_smfc_set_watermark(priv->smfc, 0x02, 0x01);
+	ipu_cpmem_set_high_priority(priv->idmac_ch);
+	ipu_idmac_enable_watermark(priv->idmac_ch, true);
+	ipu_cpmem_set_axi_id(priv->idmac_ch, 0);
+	ipu_idmac_lock_enable(priv->idmac_ch, 8);
+
+	burst_size = ipu_cpmem_get_burstsize(priv->idmac_ch);
+	burst_size = passthrough ?
+		(burst_size >> 3) - 1 : (burst_size >> 2) - 1;
+
+	ipu_smfc_set_burstsize(priv->smfc, burst_size);
+
+	if (image.pix.field == V4L2_FIELD_NONE &&
+	    V4L2_FIELD_HAS_BOTH(infmt->field))
+		ipu_cpmem_interlaced_scan(priv->idmac_ch,
+					  image.pix.bytesperline);
+
+	ipu_idmac_set_double_buffer(priv->idmac_ch, true);
+
+	return 0;
+}
+
+static void csi_idmac_unsetup(struct csi_priv *priv,
+			      enum vb2_buffer_state state)
+{
+	ipu_idmac_disable_channel(priv->idmac_ch);
+	ipu_smfc_disable(priv->smfc);
+
+	csi_idmac_unsetup_vb2_buf(priv, state);
+}
+
+static int csi_idmac_setup(struct csi_priv *priv)
+{
+	int ret;
+
+	ret = csi_idmac_setup_channel(priv);
+	if (ret)
+		return ret;
+
+	ipu_cpmem_dump(priv->idmac_ch);
+	ipu_dump(priv->ipu);
+
+	ipu_smfc_enable(priv->smfc);
+
+	/* set buffers ready */
+	ipu_idmac_select_buffer(priv->idmac_ch, 0);
+	ipu_idmac_select_buffer(priv->idmac_ch, 1);
+
+	/* enable the channels */
+	ipu_idmac_enable_channel(priv->idmac_ch);
+
+	return 0;
+}
+
+static int csi_idmac_start(struct csi_priv *priv)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct v4l2_pix_format *outfmt;
+	int ret;
+
+	ret = csi_idmac_get_ipu_resources(priv);
+	if (ret)
+		return ret;
+
+	ipu_smfc_map_channel(priv->smfc, priv->csi_id, priv->vc_num);
+
+	outfmt = &vdev->fmt.fmt.pix;
+
+	ret = imx_media_alloc_dma_buf(priv->md, &priv->underrun_buf,
+				      outfmt->sizeimage);
+	if (ret)
+		goto out_put_ipu;
+
+	priv->ipu_buf_num = 0;
+
+	/* init EOF completion waitq */
+	init_completion(&priv->last_eof_comp);
+	priv->last_eof = false;
+
+	ret = csi_idmac_setup(priv);
+	if (ret) {
+		v4l2_err(&priv->sd, "csi_idmac_setup failed: %d\n", ret);
+		goto out_free_dma_buf;
+	}
+
+	priv->nfb4eof_irq = ipu_idmac_channel_irq(priv->ipu,
+						 priv->idmac_ch,
+						 IPU_IRQ_NFB4EOF);
+	ret = devm_request_irq(priv->dev, priv->nfb4eof_irq,
+			       csi_idmac_nfb4eof_interrupt, 0,
+			       "imx-smfc-nfb4eof", priv);
+	if (ret) {
+		v4l2_err(&priv->sd,
+			 "Error registering NFB4EOF irq: %d\n", ret);
+		goto out_unsetup;
+	}
+
+	priv->eof_irq = ipu_idmac_channel_irq(priv->ipu, priv->idmac_ch,
+					      IPU_IRQ_EOF);
+
+	ret = devm_request_irq(priv->dev, priv->eof_irq,
+			       csi_idmac_eof_interrupt, 0,
+			       "imx-smfc-eof", priv);
+	if (ret) {
+		v4l2_err(&priv->sd,
+			 "Error registering eof irq: %d\n", ret);
+		goto out_free_nfb4eof_irq;
+	}
+
+	/* start the EOF timeout timer */
+	mod_timer(&priv->eof_timeout_timer,
+		  jiffies + msecs_to_jiffies(IMX_MEDIA_EOF_TIMEOUT));
+
+	return 0;
+
+out_free_nfb4eof_irq:
+	devm_free_irq(priv->dev, priv->nfb4eof_irq, priv);
+out_unsetup:
+	csi_idmac_unsetup(priv, VB2_BUF_STATE_QUEUED);
+out_free_dma_buf:
+	imx_media_free_dma_buf(priv->md, &priv->underrun_buf);
+out_put_ipu:
+	csi_idmac_put_ipu_resources(priv);
+	return ret;
+}
+
+static void csi_idmac_stop(struct csi_priv *priv)
+{
+	unsigned long flags;
+	int ret;
+
+	/* mark next EOF interrupt as the last before stream off */
+	spin_lock_irqsave(&priv->irqlock, flags);
+	priv->last_eof = true;
+	spin_unlock_irqrestore(&priv->irqlock, flags);
+
+	/*
+	 * and then wait for interrupt handler to mark completion.
+	 */
+	ret = wait_for_completion_timeout(
+		&priv->last_eof_comp, msecs_to_jiffies(IMX_MEDIA_EOF_TIMEOUT));
+	if (ret == 0)
+		v4l2_warn(&priv->sd, "wait last EOF timeout\n");
+
+	devm_free_irq(priv->dev, priv->eof_irq, priv);
+	devm_free_irq(priv->dev, priv->nfb4eof_irq, priv);
+
+	csi_idmac_unsetup(priv, VB2_BUF_STATE_ERROR);
+
+	imx_media_free_dma_buf(priv->md, &priv->underrun_buf);
+
+	/* cancel the EOF timeout timer */
+	del_timer_sync(&priv->eof_timeout_timer);
+
+	csi_idmac_put_ipu_resources(priv);
+}
+
+/* Update the CSI whole sensor and active windows */
+static int csi_setup(struct csi_priv *priv)
+{
+	struct v4l2_mbus_framefmt *infmt, *outfmt;
+	struct v4l2_mbus_config sensor_mbus_cfg;
+	struct v4l2_of_endpoint *sensor_ep;
+	struct v4l2_mbus_framefmt if_fmt;
+
+	infmt = &priv->format_mbus[CSI_SINK_PAD];
+	outfmt = &priv->format_mbus[priv->active_output_pad];
+	sensor_ep = &priv->sensor->sensor_ep;
+
+	/* compose mbus_config from sensor endpoint */
+	sensor_mbus_cfg.type = sensor_ep->bus_type;
+	sensor_mbus_cfg.flags = (sensor_ep->bus_type == V4L2_MBUS_CSI2) ?
+		sensor_ep->bus.mipi_csi2.flags :
+		sensor_ep->bus.parallel.flags;
+
+	/*
+	 * we need to pass input sensor frame to CSI interface, but
+	 * with translated field type from output format
+	 */
+	if_fmt = *infmt;
+	if_fmt.field = outfmt->field;
+
+	ipu_csi_set_window(priv->csi, &priv->crop);
+
+	ipu_csi_init_interface(priv->csi, &sensor_mbus_cfg, &if_fmt);
+
+	ipu_csi_set_dest(priv->csi, priv->dest);
+
+	ipu_csi_dump(priv->csi);
+
+	return 0;
+}
+
+static int csi_start(struct csi_priv *priv)
+{
+	int ret;
+
+	if (!priv->sensor) {
+		v4l2_err(&priv->sd, "no sensor attached\n");
+		return -EINVAL;
+	}
+
+	if (priv->dest == IPU_CSI_DEST_IDMAC) {
+		ret = csi_idmac_start(priv);
+		if (ret)
+			return ret;
+	}
+
+	ret = csi_setup(priv);
+	if (ret)
+		goto idmac_stop;
+
+	/* start the frame interval monitor */
+	if (priv->fim) {
+		ret = imx_media_fim_set_stream(priv->fim, priv->sensor, true);
+		if (ret)
+			goto idmac_stop;
+	}
+
+	ret = ipu_csi_enable(priv->csi);
+	if (ret) {
+		v4l2_err(&priv->sd, "CSI enable error: %d\n", ret);
+		goto fim_off;
+	}
+
+	return 0;
+
+fim_off:
+	if (priv->fim)
+		imx_media_fim_set_stream(priv->fim, priv->sensor, false);
+idmac_stop:
+	if (priv->dest == IPU_CSI_DEST_IDMAC)
+		csi_idmac_stop(priv);
+	return ret;
+}
+
+static void csi_stop(struct csi_priv *priv)
+{
+	if (priv->dest == IPU_CSI_DEST_IDMAC)
+		csi_idmac_stop(priv);
+
+	/* stop the frame interval monitor */
+	if (priv->fim)
+		imx_media_fim_set_stream(priv->fim, priv->sensor, false);
+
+	ipu_csi_disable(priv->csi);
+}
+
+/*
+ * V4L2 subdev operations.
+ */
+
+static int csi_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	int ret = 0;
+
+	mutex_lock(&priv->lock);
+
+	if (!priv->src_sd || !priv->sink) {
+		ret = -EPIPE;
+		goto out;
+	}
+
+	dev_dbg(priv->dev, "stream %s\n", enable ? "ON" : "OFF");
+
+	if (enable && !priv->stream_on)
+		ret = csi_start(priv);
+	else if (!enable && priv->stream_on)
+		csi_stop(priv);
+
+	if (!ret)
+		priv->stream_on = enable;
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int csi_s_power(struct v4l2_subdev *sd, int on)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	int ret = 0;
+
+	dev_dbg(priv->dev, "power %s\n", on ? "ON" : "OFF");
+
+	mutex_lock(&priv->lock);
+
+	/*
+	 * If the power count is modified from 0 to != 0 or from != 0 to 0,
+	 * update the power state.
+	 */
+	if (priv->power_count == !on) {
+		if (priv->fim) {
+			ret = imx_media_fim_set_power(priv->fim, on);
+			if (ret)
+				goto out;
+		}
+	}
+
+	/* Update the power count. */
+	priv->power_count += on ? 1 : -1;
+	WARN_ON(priv->power_count < 0);
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int csi_link_setup(struct media_entity *entity,
+			  const struct media_pad *local,
+			  const struct media_pad *remote, u32 flags)
+{
+	struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity);
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_subdev *remote_sd;
+	int ret = 0;
+
+	dev_dbg(priv->dev, "link setup %s -> %s\n", remote->entity->name,
+		local->entity->name);
+
+	mutex_lock(&priv->lock);
+
+	if (local->flags & MEDIA_PAD_FL_SINK) {
+		if (!is_media_entity_v4l2_subdev(remote->entity)) {
+			ret = -EINVAL;
+			goto out;
+		}
+
+		remote_sd = media_entity_to_v4l2_subdev(remote->entity);
+
+		if (flags & MEDIA_LNK_FL_ENABLED) {
+			if (priv->src_sd) {
+				ret = -EBUSY;
+				goto out;
+			}
+			priv->src_sd = remote_sd;
+		} else {
+			priv->src_sd = NULL;
+		}
+
+		goto out;
+	}
+
+	/* this is a source pad */
+
+	if (flags & MEDIA_LNK_FL_ENABLED) {
+		if (priv->sink) {
+			ret = -EBUSY;
+			goto out;
+		}
+	} else {
+		priv->sink = NULL;
+		goto out;
+	}
+
+	/* record which output pad is now active */
+	priv->active_output_pad = local->index;
+
+	/* set CSI destination */
+	if (local->index == CSI_SRC_PAD_IDMAC) {
+		if (!is_media_entity_v4l2_video_device(remote->entity)) {
+			ret = -EINVAL;
+			goto out;
+		}
+
+		priv->dest = IPU_CSI_DEST_IDMAC;
+	} else {
+		if (!is_media_entity_v4l2_subdev(remote->entity)) {
+			ret = -EINVAL;
+			goto out;
+		}
+
+		remote_sd = media_entity_to_v4l2_subdev(remote->entity);
+		switch (remote_sd->grp_id) {
+		case IMX_MEDIA_GRP_ID_VDIC:
+			priv->dest = IPU_CSI_DEST_VDIC;
+			break;
+		case IMX_MEDIA_GRP_ID_IC_PRP:
+			priv->dest = IPU_CSI_DEST_IC;
+			break;
+		default:
+			ret = -EINVAL;
+			goto out;
+		}
+	}
+
+	priv->sink = remote->entity;
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int csi_link_validate(struct v4l2_subdev *sd,
+			     struct media_link *link,
+			     struct v4l2_subdev_format *source_fmt,
+			     struct v4l2_subdev_format *sink_fmt)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_of_endpoint *sensor_ep;
+	struct imx_media_subdev *sensor;
+	bool is_csi2;
+	int ret;
+
+	ret = v4l2_subdev_link_validate_default(sd, link,
+						source_fmt, sink_fmt);
+	if (ret)
+		return ret;
+
+	ret = v4l2_subdev_link_validate_frame_interval(link);
+	if (ret)
+		return ret;
+
+	sensor = __imx_media_find_sensor(priv->md, &priv->sd.entity);
+	if (IS_ERR(sensor)) {
+		v4l2_err(&priv->sd, "no sensor attached\n");
+		return PTR_ERR(priv->sensor);
+	}
+
+	mutex_lock(&priv->lock);
+
+	priv->sensor = sensor;
+	sensor_ep = &priv->sensor->sensor_ep;
+
+	is_csi2 = (sensor_ep->bus_type == V4L2_MBUS_CSI2);
+
+	if (is_csi2) {
+		int vc_num = 0;
+		/*
+		 * NOTE! It seems the virtual channels from the mipi csi-2
+		 * receiver are used only for routing by the video mux's,
+		 * or for hard-wired routing to the CSI's. Once the stream
+		 * enters the CSI's however, they are treated internally
+		 * in the IPU as virtual channel 0.
+		 */
+#if 0
+		mutex_unlock(&priv->lock);
+		vc_num = imx_media_find_mipi_csi2_channel(priv->md,
+							  &priv->sd.entity);
+		if (vc_num < 0)
+			return vc_num;
+		mutex_lock(&priv->lock);
+#endif
+		ipu_csi_set_mipi_datatype(priv->csi, vc_num,
+					  &priv->format_mbus[CSI_SINK_PAD]);
+	}
+
+	/* select either parallel or MIPI-CSI2 as input to CSI */
+	ipu_set_csi_src_mux(priv->ipu, priv->csi_id, is_csi2);
+
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int csi_eof_isr(struct v4l2_subdev *sd, u32 status, bool *handled)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	unsigned long flags;
+
+	spin_lock_irqsave(&priv->irqlock, flags);
+	csi_call_fim(priv);
+	spin_unlock_irqrestore(&priv->irqlock, flags);
+
+	return 0;
+}
+
+static int csi_try_crop(struct csi_priv *priv, struct v4l2_rect *crop,
+			struct imx_media_subdev *sensor)
+{
+	struct v4l2_of_endpoint *sensor_ep;
+	struct v4l2_mbus_framefmt *infmt;
+
+	infmt = &priv->format_mbus[CSI_SINK_PAD];
+	sensor_ep = &sensor->sensor_ep;
+
+	crop->width = min_t(__u32, infmt->width, crop->width);
+	if (crop->left + crop->width > infmt->width)
+		crop->left = infmt->width - crop->width;
+	/* adjust crop left/width to h/w alignment restrictions */
+	crop->left &= ~0x3;
+	crop->width &= ~0x7;
+
+	/*
+	 * FIXME: not sure why yet, but on interlaced bt.656,
+	 * changing the vertical cropping causes loss of vertical
+	 * sync, so fix it to NTSC/PAL active lines. NTSC contains
+	 * 2 extra lines of active video that need to be cropped.
+	 */
+	if (sensor_ep->bus_type == V4L2_MBUS_BT656 &&
+	    (V4L2_FIELD_HAS_BOTH(infmt->field) ||
+	     infmt->field == V4L2_FIELD_ALTERNATE)) {
+		crop->height = infmt->height;
+		crop->top = (infmt->height == 480) ? 2 : 0;
+	} else {
+		crop->height = min_t(__u32, infmt->height, crop->height);
+		if (crop->top + crop->height > infmt->height)
+			crop->top = infmt->height - crop->height;
+	}
+
+	return 0;
+}
+
+static int csi_enum_mbus_code(struct v4l2_subdev *sd,
+			      struct v4l2_subdev_pad_config *cfg,
+			      struct v4l2_subdev_mbus_code_enum *code)
+{
+	if (code->pad >= CSI_NUM_PADS)
+		return -EINVAL;
+
+	if (code->pad == CSI_SRC_PAD_DIRECT)
+		return imx_media_enum_ipu_format(NULL, &code->code,
+						 code->index, true);
+
+	return imx_media_enum_format(NULL, &code->code, code->index,
+				     true, false);
+}
+
+static int csi_get_fmt(struct v4l2_subdev *sd,
+		       struct v4l2_subdev_pad_config *cfg,
+		       struct v4l2_subdev_format *sdformat)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+
+	if (sdformat->pad >= CSI_NUM_PADS)
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	sdformat->format = priv->format_mbus[sdformat->pad];
+
+	mutex_unlock(&priv->lock);
+
+	return 0;
+}
+
+static int csi_set_fmt(struct v4l2_subdev *sd,
+		       struct v4l2_subdev_pad_config *cfg,
+		       struct v4l2_subdev_format *sdformat)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	const struct imx_media_pixfmt *cc, *incc;
+	struct v4l2_mbus_framefmt *infmt;
+	struct imx_media_subdev *sensor;
+	struct v4l2_rect crop;
+	int ret = 0;
+	u32 code;
+
+	if (sdformat->pad >= CSI_NUM_PADS)
+		return -EINVAL;
+
+	sensor = imx_media_find_sensor(priv->md, &priv->sd.entity);
+	if (IS_ERR(sensor)) {
+		v4l2_err(&priv->sd, "no sensor attached\n");
+		return PTR_ERR(sensor);
+	}
+
+	mutex_lock(&priv->lock);
+
+	if (priv->stream_on) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	infmt = &priv->format_mbus[CSI_SINK_PAD];
+
+	v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
+			      W_ALIGN, &sdformat->format.height,
+			      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
+
+	switch (sdformat->pad) {
+	case CSI_SRC_PAD_DIRECT:
+	case CSI_SRC_PAD_IDMAC:
+		crop.left = priv->crop.left;
+		crop.top = priv->crop.top;
+		crop.width = sdformat->format.width;
+		crop.height = sdformat->format.height;
+		ret = csi_try_crop(priv, &crop, sensor);
+		if (ret)
+			goto out;
+		sdformat->format.width = crop.width;
+		sdformat->format.height = crop.height;
+
+		if (sdformat->pad == CSI_SRC_PAD_IDMAC) {
+			cc = imx_media_find_format(0, sdformat->format.code,
+						   true, false);
+			if (!cc) {
+				imx_media_enum_format(NULL, &code, 0,
+						      true, false);
+				cc = imx_media_find_format(0, code,
+							   true, false);
+				sdformat->format.code = cc->codes[0];
+			}
+
+			incc = priv->cc[CSI_SINK_PAD];
+			if (cc->cs != incc->cs) {
+				sdformat->format.code = infmt->code;
+				cc = imx_media_find_format(
+					0, sdformat->format.code,
+					true, false);
+			}
+
+			if (sdformat->format.field != V4L2_FIELD_NONE)
+				sdformat->format.field = infmt->field;
+		} else {
+			cc = imx_media_find_ipu_format(0, sdformat->format.code,
+						       true);
+			if (!cc) {
+				imx_media_enum_ipu_format(NULL, &code, 0, true);
+				cc = imx_media_find_ipu_format(0, code, true);
+				sdformat->format.code = cc->codes[0];
+			}
+
+			sdformat->format.field = infmt->field;
+		}
+
+		/*
+		 * translate V4L2_FIELD_ALTERNATE to SEQ_TB or SEQ_BT
+		 * depending on input height (assume NTSC top-bottom
+		 * order if 480 lines, otherwise PAL bottom-top order).
+		 */
+		if (sdformat->format.field == V4L2_FIELD_ALTERNATE) {
+			sdformat->format.field =  (infmt->height == 480) ?
+				V4L2_FIELD_SEQ_TB : V4L2_FIELD_SEQ_BT;
+		}
+		break;
+	case CSI_SINK_PAD:
+		cc = imx_media_find_format(0, sdformat->format.code,
+					   true, false);
+		if (!cc) {
+			imx_media_enum_format(NULL, &code, 0, true, false);
+			cc = imx_media_find_format(0, code, true, false);
+			sdformat->format.code = cc->codes[0];
+		}
+		break;
+	default:
+		ret = -EINVAL;
+		goto out;
+	}
+
+	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
+		cfg->try_fmt = sdformat->format;
+	} else {
+		priv->format_mbus[sdformat->pad] = sdformat->format;
+		priv->cc[sdformat->pad] = cc;
+		/* Update the crop window if this is an output pad  */
+		if (sdformat->pad == CSI_SRC_PAD_DIRECT ||
+		    sdformat->pad == CSI_SRC_PAD_IDMAC)
+			priv->crop = crop;
+	}
+
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int csi_get_selection(struct v4l2_subdev *sd,
+			     struct v4l2_subdev_pad_config *cfg,
+			     struct v4l2_subdev_selection *sel)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_mbus_framefmt *infmt;
+	int ret = 0;
+
+	if (sel->pad >= CSI_NUM_PADS || sel->pad == CSI_SINK_PAD)
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	infmt = &priv->format_mbus[CSI_SINK_PAD];
+
+	switch (sel->target) {
+	case V4L2_SEL_TGT_CROP_BOUNDS:
+		sel->r.left = 0;
+		sel->r.top = 0;
+		sel->r.width = infmt->width;
+		sel->r.height = infmt->height;
+		break;
+	case V4L2_SEL_TGT_CROP:
+		sel->r = priv->crop;
+		break;
+	default:
+		ret = -EINVAL;
+	}
+
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int csi_set_selection(struct v4l2_subdev *sd,
+			     struct v4l2_subdev_pad_config *cfg,
+			     struct v4l2_subdev_selection *sel)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_mbus_framefmt *outfmt;
+	struct imx_media_subdev *sensor;
+	int ret = 0;
+
+	if (sel->pad >= CSI_NUM_PADS ||
+	    sel->pad == CSI_SINK_PAD ||
+	    sel->target != V4L2_SEL_TGT_CROP)
+		return -EINVAL;
+
+	sensor = imx_media_find_sensor(priv->md, &priv->sd.entity);
+	if (IS_ERR(sensor)) {
+		v4l2_err(&priv->sd, "no sensor attached\n");
+		return PTR_ERR(sensor);
+	}
+
+	mutex_lock(&priv->lock);
+
+	if (priv->stream_on) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	/*
+	 * Modifying the crop rectangle always changes the format on the source
+	 * pad. If the KEEP_CONFIG flag is set, just return the current crop
+	 * rectangle.
+	 */
+	if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
+		sel->r = priv->crop;
+		if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
+			cfg->try_crop = sel->r;
+		goto out;
+	}
+
+	outfmt = &priv->format_mbus[sel->pad];
+
+	ret = csi_try_crop(priv, &sel->r, sensor);
+	if (ret)
+		goto out;
+
+	if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
+		cfg->try_crop = sel->r;
+	} else {
+		priv->crop = sel->r;
+		/* Update the source format */
+		outfmt->width = sel->r.width;
+		outfmt->height = sel->r.height;
+	}
+
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int csi_subscribe_event(struct v4l2_subdev *sd, struct v4l2_fh *fh,
+			       struct v4l2_event_subscription *sub)
+{
+	if (sub->type != V4L2_EVENT_NEW_FRAME_BEFORE_EOF &&
+	    sub->type != V4L2_EVENT_FRAME_INTERVAL_ERROR)
+		return -EINVAL;
+	if (sub->id != 0)
+		return -EINVAL;
+
+	return v4l2_event_subscribe(fh, sub, 0, NULL);
+}
+
+static int csi_unsubscribe_event(struct v4l2_subdev *sd, struct v4l2_fh *fh,
+				 struct v4l2_event_subscription *sub)
+{
+	return v4l2_event_unsubscribe(fh, sub);
+}
+
+/*
+ * retrieve our pads parsed from the OF graph by the media device
+ */
+static int csi_registered(struct v4l2_subdev *sd)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	int i, ret;
+	u32 code;
+
+	/* get media device */
+	priv->md = dev_get_drvdata(sd->v4l2_dev->dev);
+
+	/* get handle to IPU CSI */
+	priv->csi = ipu_csi_get(priv->ipu, priv->csi_id);
+	if (IS_ERR(priv->csi)) {
+		v4l2_err(&priv->sd, "failed to get CSI%d\n", priv->csi_id);
+		return PTR_ERR(priv->csi);
+	}
+
+	for (i = 0; i < CSI_NUM_PADS; i++) {
+		priv->pad[i].flags = (i == CSI_SINK_PAD) ?
+			MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
+
+		code = 0;
+		if (i == CSI_SRC_PAD_DIRECT)
+			imx_media_enum_ipu_format(NULL, &code, 0, true);
+
+		/* set a default mbus format  */
+		ret = imx_media_init_mbus_fmt(&priv->format_mbus[i],
+					      640, 480, code, V4L2_FIELD_NONE,
+					      &priv->cc[i]);
+		if (ret)
+			goto put_csi;
+	}
+
+	priv->fim = imx_media_fim_init(&priv->sd);
+	if (IS_ERR(priv->fim)) {
+		ret = PTR_ERR(priv->fim);
+		goto put_csi;
+	}
+
+	ret = media_entity_pads_init(&sd->entity, CSI_NUM_PADS, priv->pad);
+	if (ret)
+		goto free_fim;
+
+	ret = imx_media_capture_device_register(priv->vdev);
+	if (ret)
+		goto free_fim;
+
+	return 0;
+
+free_fim:
+	if (priv->fim)
+		imx_media_fim_free(priv->fim);
+put_csi:
+	ipu_csi_put(priv->csi);
+	return ret;
+}
+
+static void csi_unregistered(struct v4l2_subdev *sd)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+
+	imx_media_capture_device_unregister(priv->vdev);
+
+	if (priv->fim)
+		imx_media_fim_free(priv->fim);
+
+	if (!IS_ERR_OR_NULL(priv->csi))
+		ipu_csi_put(priv->csi);
+}
+
+static struct media_entity_operations csi_entity_ops = {
+	.link_setup = csi_link_setup,
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static struct v4l2_subdev_core_ops csi_core_ops = {
+	.s_power = csi_s_power,
+	.interrupt_service_routine = csi_eof_isr,
+	.subscribe_event = csi_subscribe_event,
+	.unsubscribe_event = csi_unsubscribe_event,
+};
+
+static struct v4l2_subdev_video_ops csi_video_ops = {
+	.s_stream = csi_s_stream,
+};
+
+static struct v4l2_subdev_pad_ops csi_pad_ops = {
+	.enum_mbus_code = csi_enum_mbus_code,
+	.get_fmt = csi_get_fmt,
+	.set_fmt = csi_set_fmt,
+	.get_selection = csi_get_selection,
+	.set_selection = csi_set_selection,
+	.link_validate = csi_link_validate,
+};
+
+static struct v4l2_subdev_ops csi_subdev_ops = {
+	.core = &csi_core_ops,
+	.video = &csi_video_ops,
+	.pad = &csi_pad_ops,
+};
+
+static struct v4l2_subdev_internal_ops csi_internal_ops = {
+	.registered = csi_registered,
+	.unregistered = csi_unregistered,
+};
+
+static int imx_csi_probe(struct platform_device *pdev)
+{
+	struct ipu_client_platformdata *pdata;
+	struct pinctrl *pinctrl;
+	struct csi_priv *priv;
+	int ret;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, &priv->sd);
+	priv->dev = &pdev->dev;
+
+	ret = dma_set_coherent_mask(priv->dev, DMA_BIT_MASK(32));
+	if (ret)
+		return ret;
+
+	/* get parent IPU */
+	priv->ipu = dev_get_drvdata(priv->dev->parent);
+
+	/* get our CSI id */
+	pdata = priv->dev->platform_data;
+	priv->csi_id = pdata->csi;
+	priv->smfc_id = (priv->csi_id == 0) ? 0 : 2;
+
+	init_timer(&priv->eof_timeout_timer);
+	priv->eof_timeout_timer.data = (unsigned long)priv;
+	priv->eof_timeout_timer.function = csi_idmac_eof_timeout;
+	spin_lock_init(&priv->irqlock);
+
+	v4l2_subdev_init(&priv->sd, &csi_subdev_ops);
+	v4l2_set_subdevdata(&priv->sd, priv);
+	priv->sd.internal_ops = &csi_internal_ops;
+	priv->sd.entity.ops = &csi_entity_ops;
+	priv->sd.entity.function = MEDIA_ENT_F_PROC_VIDEO_PIXEL_FORMATTER;
+	priv->sd.dev = &pdev->dev;
+	priv->sd.of_node = pdata->of_node;
+	priv->sd.owner = THIS_MODULE;
+	priv->sd.flags = V4L2_SUBDEV_FL_HAS_DEVNODE | V4L2_SUBDEV_FL_HAS_EVENTS;
+	priv->sd.grp_id = priv->csi_id ?
+		IMX_MEDIA_GRP_ID_CSI1 : IMX_MEDIA_GRP_ID_CSI0;
+	imx_media_grp_id_to_sd_name(priv->sd.name, sizeof(priv->sd.name),
+				    priv->sd.grp_id, ipu_get_num(priv->ipu));
+
+	priv->vdev = imx_media_capture_device_init(&priv->sd,
+						   CSI_SRC_PAD_IDMAC);
+	if (IS_ERR(priv->vdev))
+		return PTR_ERR(priv->vdev);
+
+	v4l2_ctrl_handler_init(&priv->ctrl_hdlr, 0);
+	priv->sd.ctrl_handler = &priv->ctrl_hdlr;
+
+	/*
+	 * The IPUv3 driver did not assign an of_node to this
+	 * device. As a result, pinctrl does not automatically
+	 * configure our pin groups, so we need to do that manually
+	 * here, after setting this device's of_node.
+	 */
+	priv->dev->of_node = pdata->of_node;
+	pinctrl = devm_pinctrl_get_select_default(priv->dev);
+
+	mutex_init(&priv->lock);
+
+	ret = v4l2_async_register_subdev(&priv->sd);
+	if (ret)
+		goto free;
+
+	return 0;
+free:
+	v4l2_ctrl_handler_free(&priv->ctrl_hdlr);
+	mutex_destroy(&priv->lock);
+	imx_media_capture_device_remove(priv->vdev);
+	return ret;
+}
+
+static int imx_csi_remove(struct platform_device *pdev)
+{
+	struct v4l2_subdev *sd = platform_get_drvdata(pdev);
+	struct csi_priv *priv = sd_to_dev(sd);
+
+	v4l2_ctrl_handler_free(&priv->ctrl_hdlr);
+	mutex_destroy(&priv->lock);
+	imx_media_capture_device_remove(priv->vdev);
+	v4l2_async_unregister_subdev(sd);
+	media_entity_cleanup(&sd->entity);
+
+	return 0;
+}
+
+static const struct platform_device_id imx_csi_ids[] = {
+	{ .name = "imx-ipuv3-csi" },
+	{ },
+};
+MODULE_DEVICE_TABLE(platform, imx_csi_ids);
+
+static struct platform_driver imx_csi_driver = {
+	.probe = imx_csi_probe,
+	.remove = imx_csi_remove,
+	.id_table = imx_csi_ids,
+	.driver = {
+		.name = "imx-ipuv3-csi",
+	},
+};
+module_platform_driver(imx_csi_driver);
+
+MODULE_DESCRIPTION("i.MX CSI subdev driver");
+MODULE_AUTHOR("Steve Longerbeam <steve_longerbeam@mentor.com>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:imx-ipuv3-csi");
-- 
2.7.4

[PATCH v5 25/39] media: imx: Add CSI subdev driver

[Steve Longerbeam]

This is a media entity subdevice for the i.MX Camera
Sensor Interface module.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/Kconfig         |   14 +
 drivers/staging/media/imx/Makefile        |    2 +
 drivers/staging/media/imx/imx-media-csi.c | 1311 +++++++++++++++++++++++++++++
 3 files changed, 1327 insertions(+)
 create mode 100644 drivers/staging/media/imx/imx-media-csi.c

diff --git a/drivers/staging/media/imx/Kconfig b/drivers/staging/media/imx/Kconfig
index 62a3c34..e27ad6d 100644
--- a/drivers/staging/media/imx/Kconfig
+++ b/drivers/staging/media/imx/Kconfig
@@ -4,3 +4,17 @@ config VIDEO_IMX_MEDIA
 	---help---
 	  Say yes here to enable support for video4linux media controller
 	  driver for the i.MX5/6 SOC.
+
+if VIDEO_IMX_MEDIA
+menu "i.MX5/6 Media Sub devices"
+
+config VIDEO_IMX_CSI
+	tristate "i.MX5/6 Camera Sensor Interface driver"
+	depends on VIDEO_IMX_MEDIA && VIDEO_DEV && I2C
+	select VIDEOBUF2_DMA_CONTIG
+	default y
+	---help---
+	  A video4linux camera sensor interface driver for i.MX5/6.
+
+endmenu
+endif
diff --git a/drivers/staging/media/imx/Makefile b/drivers/staging/media/imx/Makefile
index 4606a3a..c054490 100644
--- a/drivers/staging/media/imx/Makefile
+++ b/drivers/staging/media/imx/Makefile
@@ -4,3 +4,5 @@ imx-media-common-objs := imx-media-utils.o imx-media-fim.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-common.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-capture.o
+
+obj-$(CONFIG_VIDEO_IMX_CSI) += imx-media-csi.o
diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
new file mode 100644
index 0000000..ab78ff7
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -0,0 +1,1311 @@
+/*
+ * V4L2 Capture CSI Subdev for Freescale i.MX5/6 SOC
+ *
+ * Copyright (c) 2014-2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-mc.h>
+#include <media/v4l2-of.h>
+#include <media/v4l2-subdev.h>
+#include <media/videobuf2-dma-contig.h>
+#include <video/imx-ipu-v3.h>
+#include <media/imx.h>
+#include "imx-media.h"
+
+/*
+ * Min/Max supported width and heights.
+ *
+ * We allow planar output, so we have to align width by 16 pixels
+ * to meet IDMAC alignment requirements.
+ *
+ * TODO: move this into pad format negotiation, if capture device
+ * has not requested planar formats, we should allow 8 pixel
+ * alignment.
+ */
+#define MIN_W       176
+#define MIN_H       144
+#define MAX_W      4096
+#define MAX_H      4096
+#define W_ALIGN    4 /* multiple of 16 pixels */
+#define H_ALIGN    1 /* multiple of 2 lines */
+#define S_ALIGN    1 /* multiple of 2 */
+
+struct csi_priv {
+	struct device *dev;
+	struct ipu_soc *ipu;
+	struct imx_media_dev *md;
+	struct v4l2_subdev sd;
+	struct media_pad pad[CSI_NUM_PADS];
+	/* the video device at IDMAC output pad */
+	struct imx_media_video_dev *vdev;
+	struct imx_media_fim *fim;
+	int csi_id;
+	int smfc_id;
+
+	/* lock to protect all members below */
+	struct mutex lock;
+
+	int active_output_pad;
+
+	struct ipuv3_channel *idmac_ch;
+	struct ipu_smfc *smfc;
+	struct ipu_csi *csi;
+
+	struct v4l2_mbus_framefmt format_mbus[CSI_NUM_PADS];
+	const struct imx_media_pixfmt *cc[CSI_NUM_PADS];
+	struct v4l2_rect crop;
+
+	/* active vb2 buffers to send to video dev sink */
+	struct imx_media_buffer *active_vb2_buf[2];
+	struct imx_media_dma_buf underrun_buf;
+
+	int ipu_buf_num;  /* ipu double buffer index: 0-1 */
+
+	/* the sink for the captured frames */
+	struct media_entity *sink;
+	enum ipu_csi_dest dest;
+	/* the source subdev */
+	struct v4l2_subdev *src_sd;
+
+	/* the mipi virtual channel number at link validate */
+	int vc_num;
+
+	/* the attached sensor at stream on */
+	struct imx_media_subdev *sensor;
+
+	spinlock_t irqlock; /* protect eof_irq handler */
+	struct timer_list eof_timeout_timer;
+	int eof_irq;
+	int nfb4eof_irq;
+
+	struct v4l2_ctrl_handler ctrl_hdlr;
+
+	int power_count; /* power counter */
+	bool stream_on;  /* streaming is on */
+	bool last_eof;   /* waiting for last EOF at stream off */
+	struct completion last_eof_comp;
+};
+
+static inline struct csi_priv *sd_to_dev(struct v4l2_subdev *sdev)
+{
+	return container_of(sdev, struct csi_priv, sd);
+}
+
+static void csi_idmac_put_ipu_resources(struct csi_priv *priv)
+{
+	if (!IS_ERR_OR_NULL(priv->idmac_ch))
+		ipu_idmac_put(priv->idmac_ch);
+	priv->idmac_ch = NULL;
+
+	if (!IS_ERR_OR_NULL(priv->smfc))
+		ipu_smfc_put(priv->smfc);
+	priv->smfc = NULL;
+}
+
+static int csi_idmac_get_ipu_resources(struct csi_priv *priv)
+{
+	int ch_num, ret;
+
+	ch_num = IPUV3_CHANNEL_CSI0 + priv->smfc_id;
+
+	priv->smfc = ipu_smfc_get(priv->ipu, ch_num);
+	if (IS_ERR(priv->smfc)) {
+		v4l2_err(&priv->sd, "failed to get SMFC\n");
+		ret = PTR_ERR(priv->smfc);
+		goto out;
+	}
+
+	priv->idmac_ch = ipu_idmac_get(priv->ipu, ch_num);
+	if (IS_ERR(priv->idmac_ch)) {
+		v4l2_err(&priv->sd, "could not get IDMAC channel %u\n",
+			 ch_num);
+		ret = PTR_ERR(priv->idmac_ch);
+		goto out;
+	}
+
+	return 0;
+out:
+	csi_idmac_put_ipu_resources(priv);
+	return ret;
+}
+
+static void csi_vb2_buf_done(struct csi_priv *priv)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct imx_media_buffer *done, *next;
+	struct vb2_buffer *vb;
+	dma_addr_t phys;
+
+	done = priv->active_vb2_buf[priv->ipu_buf_num];
+	if (done) {
+		vb = &done->vbuf.vb2_buf;
+		vb->timestamp = ktime_get_ns();
+		vb2_buffer_done(vb, VB2_BUF_STATE_DONE);
+	}
+
+	/* get next queued buffer */
+	next = imx_media_capture_device_next_buf(vdev);
+	if (next) {
+		phys = vb2_dma_contig_plane_dma_addr(&next->vbuf.vb2_buf, 0);
+		priv->active_vb2_buf[priv->ipu_buf_num] = next;
+	} else {
+		phys = priv->underrun_buf.phys;
+		priv->active_vb2_buf[priv->ipu_buf_num] = NULL;
+	}
+
+	if (ipu_idmac_buffer_is_ready(priv->idmac_ch, priv->ipu_buf_num))
+		ipu_idmac_clear_buffer(priv->idmac_ch, priv->ipu_buf_num);
+
+	ipu_cpmem_set_buffer(priv->idmac_ch, priv->ipu_buf_num, phys);
+}
+
+static void csi_call_fim(struct csi_priv *priv)
+{
+	if (priv->fim) {
+		struct timespec cur_ts;
+
+		ktime_get_ts(&cur_ts);
+		/* call frame interval monitor */
+		imx_media_fim_eof_monitor(priv->fim, &cur_ts);
+	}
+}
+
+static irqreturn_t csi_idmac_eof_interrupt(int irq, void *dev_id)
+{
+	struct csi_priv *priv = dev_id;
+
+	spin_lock(&priv->irqlock);
+
+	if (priv->last_eof) {
+		complete(&priv->last_eof_comp);
+		priv->last_eof = false;
+		goto unlock;
+	}
+
+	csi_call_fim(priv);
+
+	csi_vb2_buf_done(priv);
+
+	/* select new IPU buf */
+	ipu_idmac_select_buffer(priv->idmac_ch, priv->ipu_buf_num);
+	/* toggle IPU double-buffer index */
+	priv->ipu_buf_num ^= 1;
+
+	/* bump the EOF timeout timer */
+	mod_timer(&priv->eof_timeout_timer,
+		  jiffies + msecs_to_jiffies(IMX_MEDIA_EOF_TIMEOUT));
+
+unlock:
+	spin_unlock(&priv->irqlock);
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t csi_idmac_nfb4eof_interrupt(int irq, void *dev_id)
+{
+	struct csi_priv *priv = dev_id;
+	static const struct v4l2_event ev = {
+		.type = V4L2_EVENT_NEW_FRAME_BEFORE_EOF,
+	};
+
+	v4l2_err(&priv->sd, "NFB4EOF\n");
+
+	v4l2_subdev_notify_event(&priv->sd, &ev);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * EOF timeout timer function. This is an unrecoverable condition
+ * without a stream restart.
+ */
+static void csi_idmac_eof_timeout(unsigned long data)
+{
+	struct csi_priv *priv = (struct csi_priv *)data;
+	struct imx_media_video_dev *vdev = priv->vdev;
+
+	v4l2_err(&priv->sd, "EOF timeout\n");
+
+	/* signal a fatal error to capture device */
+	imx_media_capture_device_error(vdev);
+}
+
+static void csi_idmac_setup_vb2_buf(struct csi_priv *priv, dma_addr_t *phys)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct imx_media_buffer *buf;
+	int i;
+
+	for (i = 0; i < 2; i++) {
+		buf = imx_media_capture_device_next_buf(vdev);
+		priv->active_vb2_buf[i] = buf;
+		phys[i] = vb2_dma_contig_plane_dma_addr(&buf->vbuf.vb2_buf, 0);
+	}
+}
+
+static void csi_idmac_unsetup_vb2_buf(struct csi_priv *priv,
+				      enum vb2_buffer_state return_state)
+{
+	struct imx_media_buffer *buf;
+	int i;
+
+	/* return any remaining active frames with error */
+	for (i = 0; i < 2; i++) {
+		buf = priv->active_vb2_buf[i];
+		if (buf) {
+			struct vb2_buffer *vb = &buf->vbuf.vb2_buf;
+
+			vb->timestamp = ktime_get_ns();
+			vb2_buffer_done(vb, return_state);
+		}
+	}
+}
+
+/* init the SMFC IDMAC channel */
+static int csi_idmac_setup_channel(struct csi_priv *priv)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct v4l2_of_endpoint *sensor_ep;
+	struct v4l2_mbus_framefmt *infmt;
+	unsigned int burst_size;
+	struct ipu_image image;
+	dma_addr_t phys[2];
+	bool passthrough;
+	int ret;
+
+	infmt = &priv->format_mbus[CSI_SINK_PAD];
+	sensor_ep = &priv->sensor->sensor_ep;
+
+	ipu_cpmem_zero(priv->idmac_ch);
+
+	memset(&image, 0, sizeof(image));
+	image.pix = vdev->fmt.fmt.pix;
+	image.rect.width = image.pix.width;
+	image.rect.height = image.pix.height;
+
+	csi_idmac_setup_vb2_buf(priv, phys);
+
+	image.phys0 = phys[0];
+	image.phys1 = phys[1];
+
+	ret = ipu_cpmem_set_image(priv->idmac_ch, &image);
+	if (ret)
+		return ret;
+
+	burst_size = (image.pix.width & 0xf) ? 8 : 16;
+
+	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
+
+	/*
+	 * If the sensor uses 16-bit parallel CSI bus, we must handle
+	 * the data internally in the IPU as 16-bit generic, aka
+	 * passthrough mode.
+	 */
+	passthrough = (sensor_ep->bus_type != V4L2_MBUS_CSI2 &&
+		       sensor_ep->bus.parallel.bus_width >= 16);
+
+	if (passthrough)
+		ipu_cpmem_set_format_passthrough(priv->idmac_ch, 16);
+
+	/*
+	 * Set the channel for the direct CSI-->memory via SMFC
+	 * use-case to very high priority, by enabling the watermark
+	 * signal in the SMFC, enabling WM in the channel, and setting
+	 * the channel priority to high.
+	 *
+	 * Refer to the i.mx6 rev. D TRM Table 36-8: Calculated priority
+	 * value.
+	 *
+	 * The WM's are set very low by intention here to ensure that
+	 * the SMFC FIFOs do not overflow.
+	 */
+	ipu_smfc_set_watermark(priv->smfc, 0x02, 0x01);
+	ipu_cpmem_set_high_priority(priv->idmac_ch);
+	ipu_idmac_enable_watermark(priv->idmac_ch, true);
+	ipu_cpmem_set_axi_id(priv->idmac_ch, 0);
+	ipu_idmac_lock_enable(priv->idmac_ch, 8);
+
+	burst_size = ipu_cpmem_get_burstsize(priv->idmac_ch);
+	burst_size = passthrough ?
+		(burst_size >> 3) - 1 : (burst_size >> 2) - 1;
+
+	ipu_smfc_set_burstsize(priv->smfc, burst_size);
+
+	if (image.pix.field == V4L2_FIELD_NONE &&
+	    V4L2_FIELD_HAS_BOTH(infmt->field))
+		ipu_cpmem_interlaced_scan(priv->idmac_ch,
+					  image.pix.bytesperline);
+
+	ipu_idmac_set_double_buffer(priv->idmac_ch, true);
+
+	return 0;
+}
+
+static void csi_idmac_unsetup(struct csi_priv *priv,
+			      enum vb2_buffer_state state)
+{
+	ipu_idmac_disable_channel(priv->idmac_ch);
+	ipu_smfc_disable(priv->smfc);
+
+	csi_idmac_unsetup_vb2_buf(priv, state);
+}
+
+static int csi_idmac_setup(struct csi_priv *priv)
+{
+	int ret;
+
+	ret = csi_idmac_setup_channel(priv);
+	if (ret)
+		return ret;
+
+	ipu_cpmem_dump(priv->idmac_ch);
+	ipu_dump(priv->ipu);
+
+	ipu_smfc_enable(priv->smfc);
+
+	/* set buffers ready */
+	ipu_idmac_select_buffer(priv->idmac_ch, 0);
+	ipu_idmac_select_buffer(priv->idmac_ch, 1);
+
+	/* enable the channels */
+	ipu_idmac_enable_channel(priv->idmac_ch);
+
+	return 0;
+}
+
+static int csi_idmac_start(struct csi_priv *priv)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct v4l2_pix_format *outfmt;
+	int ret;
+
+	ret = csi_idmac_get_ipu_resources(priv);
+	if (ret)
+		return ret;
+
+	ipu_smfc_map_channel(priv->smfc, priv->csi_id, priv->vc_num);
+
+	outfmt = &vdev->fmt.fmt.pix;
+
+	ret = imx_media_alloc_dma_buf(priv->md, &priv->underrun_buf,
+				      outfmt->sizeimage);
+	if (ret)
+		goto out_put_ipu;
+
+	priv->ipu_buf_num = 0;
+
+	/* init EOF completion waitq */
+	init_completion(&priv->last_eof_comp);
+	priv->last_eof = false;
+
+	ret = csi_idmac_setup(priv);
+	if (ret) {
+		v4l2_err(&priv->sd, "csi_idmac_setup failed: %d\n", ret);
+		goto out_free_dma_buf;
+	}
+
+	priv->nfb4eof_irq = ipu_idmac_channel_irq(priv->ipu,
+						 priv->idmac_ch,
+						 IPU_IRQ_NFB4EOF);
+	ret = devm_request_irq(priv->dev, priv->nfb4eof_irq,
+			       csi_idmac_nfb4eof_interrupt, 0,
+			       "imx-smfc-nfb4eof", priv);
+	if (ret) {
+		v4l2_err(&priv->sd,
+			 "Error registering NFB4EOF irq: %d\n", ret);
+		goto out_unsetup;
+	}
+
+	priv->eof_irq = ipu_idmac_channel_irq(priv->ipu, priv->idmac_ch,
+					      IPU_IRQ_EOF);
+
+	ret = devm_request_irq(priv->dev, priv->eof_irq,
+			       csi_idmac_eof_interrupt, 0,
+			       "imx-smfc-eof", priv);
+	if (ret) {
+		v4l2_err(&priv->sd,
+			 "Error registering eof irq: %d\n", ret);
+		goto out_free_nfb4eof_irq;
+	}
+
+	/* start the EOF timeout timer */
+	mod_timer(&priv->eof_timeout_timer,
+		  jiffies + msecs_to_jiffies(IMX_MEDIA_EOF_TIMEOUT));
+
+	return 0;
+
+out_free_nfb4eof_irq:
+	devm_free_irq(priv->dev, priv->nfb4eof_irq, priv);
+out_unsetup:
+	csi_idmac_unsetup(priv, VB2_BUF_STATE_QUEUED);
+out_free_dma_buf:
+	imx_media_free_dma_buf(priv->md, &priv->underrun_buf);
+out_put_ipu:
+	csi_idmac_put_ipu_resources(priv);
+	return ret;
+}
+
+static void csi_idmac_stop(struct csi_priv *priv)
+{
+	unsigned long flags;
+	int ret;
+
+	/* mark next EOF interrupt as the last before stream off */
+	spin_lock_irqsave(&priv->irqlock, flags);
+	priv->last_eof = true;
+	spin_unlock_irqrestore(&priv->irqlock, flags);
+
+	/*
+	 * and then wait for interrupt handler to mark completion.
+	 */
+	ret = wait_for_completion_timeout(
+		&priv->last_eof_comp, msecs_to_jiffies(IMX_MEDIA_EOF_TIMEOUT));
+	if (ret == 0)
+		v4l2_warn(&priv->sd, "wait last EOF timeout\n");
+
+	devm_free_irq(priv->dev, priv->eof_irq, priv);
+	devm_free_irq(priv->dev, priv->nfb4eof_irq, priv);
+
+	csi_idmac_unsetup(priv, VB2_BUF_STATE_ERROR);
+
+	imx_media_free_dma_buf(priv->md, &priv->underrun_buf);
+
+	/* cancel the EOF timeout timer */
+	del_timer_sync(&priv->eof_timeout_timer);
+
+	csi_idmac_put_ipu_resources(priv);
+}
+
+/* Update the CSI whole sensor and active windows */
+static int csi_setup(struct csi_priv *priv)
+{
+	struct v4l2_mbus_framefmt *infmt, *outfmt;
+	struct v4l2_mbus_config sensor_mbus_cfg;
+	struct v4l2_of_endpoint *sensor_ep;
+	struct v4l2_mbus_framefmt if_fmt;
+
+	infmt = &priv->format_mbus[CSI_SINK_PAD];
+	outfmt = &priv->format_mbus[priv->active_output_pad];
+	sensor_ep = &priv->sensor->sensor_ep;
+
+	/* compose mbus_config from sensor endpoint */
+	sensor_mbus_cfg.type = sensor_ep->bus_type;
+	sensor_mbus_cfg.flags = (sensor_ep->bus_type == V4L2_MBUS_CSI2) ?
+		sensor_ep->bus.mipi_csi2.flags :
+		sensor_ep->bus.parallel.flags;
+
+	/*
+	 * we need to pass input sensor frame to CSI interface, but
+	 * with translated field type from output format
+	 */
+	if_fmt = *infmt;
+	if_fmt.field = outfmt->field;
+
+	ipu_csi_set_window(priv->csi, &priv->crop);
+
+	ipu_csi_init_interface(priv->csi, &sensor_mbus_cfg, &if_fmt);
+
+	ipu_csi_set_dest(priv->csi, priv->dest);
+
+	ipu_csi_dump(priv->csi);
+
+	return 0;
+}
+
+static int csi_start(struct csi_priv *priv)
+{
+	int ret;
+
+	if (!priv->sensor) {
+		v4l2_err(&priv->sd, "no sensor attached\n");
+		return -EINVAL;
+	}
+
+	if (priv->dest == IPU_CSI_DEST_IDMAC) {
+		ret = csi_idmac_start(priv);
+		if (ret)
+			return ret;
+	}
+
+	ret = csi_setup(priv);
+	if (ret)
+		goto idmac_stop;
+
+	/* start the frame interval monitor */
+	if (priv->fim) {
+		ret = imx_media_fim_set_stream(priv->fim, priv->sensor, true);
+		if (ret)
+			goto idmac_stop;
+	}
+
+	ret = ipu_csi_enable(priv->csi);
+	if (ret) {
+		v4l2_err(&priv->sd, "CSI enable error: %d\n", ret);
+		goto fim_off;
+	}
+
+	return 0;
+
+fim_off:
+	if (priv->fim)
+		imx_media_fim_set_stream(priv->fim, priv->sensor, false);
+idmac_stop:
+	if (priv->dest == IPU_CSI_DEST_IDMAC)
+		csi_idmac_stop(priv);
+	return ret;
+}
+
+static void csi_stop(struct csi_priv *priv)
+{
+	if (priv->dest == IPU_CSI_DEST_IDMAC)
+		csi_idmac_stop(priv);
+
+	/* stop the frame interval monitor */
+	if (priv->fim)
+		imx_media_fim_set_stream(priv->fim, priv->sensor, false);
+
+	ipu_csi_disable(priv->csi);
+}
+
+/*
+ * V4L2 subdev operations.
+ */
+
+static int csi_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	int ret = 0;
+
+	mutex_lock(&priv->lock);
+
+	if (!priv->src_sd || !priv->sink) {
+		ret = -EPIPE;
+		goto out;
+	}
+
+	dev_dbg(priv->dev, "stream %s\n", enable ? "ON" : "OFF");
+
+	if (enable && !priv->stream_on)
+		ret = csi_start(priv);
+	else if (!enable && priv->stream_on)
+		csi_stop(priv);
+
+	if (!ret)
+		priv->stream_on = enable;
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int csi_s_power(struct v4l2_subdev *sd, int on)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	int ret = 0;
+
+	dev_dbg(priv->dev, "power %s\n", on ? "ON" : "OFF");
+
+	mutex_lock(&priv->lock);
+
+	/*
+	 * If the power count is modified from 0 to != 0 or from != 0 to 0,
+	 * update the power state.
+	 */
+	if (priv->power_count == !on) {
+		if (priv->fim) {
+			ret = imx_media_fim_set_power(priv->fim, on);
+			if (ret)
+				goto out;
+		}
+	}
+
+	/* Update the power count. */
+	priv->power_count += on ? 1 : -1;
+	WARN_ON(priv->power_count < 0);
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int csi_link_setup(struct media_entity *entity,
+			  const struct media_pad *local,
+			  const struct media_pad *remote, u32 flags)
+{
+	struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity);
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_subdev *remote_sd;
+	int ret = 0;
+
+	dev_dbg(priv->dev, "link setup %s -> %s\n", remote->entity->name,
+		local->entity->name);
+
+	mutex_lock(&priv->lock);
+
+	if (local->flags & MEDIA_PAD_FL_SINK) {
+		if (!is_media_entity_v4l2_subdev(remote->entity)) {
+			ret = -EINVAL;
+			goto out;
+		}
+
+		remote_sd = media_entity_to_v4l2_subdev(remote->entity);
+
+		if (flags & MEDIA_LNK_FL_ENABLED) {
+			if (priv->src_sd) {
+				ret = -EBUSY;
+				goto out;
+			}
+			priv->src_sd = remote_sd;
+		} else {
+			priv->src_sd = NULL;
+		}
+
+		goto out;
+	}
+
+	/* this is a source pad */
+
+	if (flags & MEDIA_LNK_FL_ENABLED) {
+		if (priv->sink) {
+			ret = -EBUSY;
+			goto out;
+		}
+	} else {
+		priv->sink = NULL;
+		goto out;
+	}
+
+	/* record which output pad is now active */
+	priv->active_output_pad = local->index;
+
+	/* set CSI destination */
+	if (local->index == CSI_SRC_PAD_IDMAC) {
+		if (!is_media_entity_v4l2_video_device(remote->entity)) {
+			ret = -EINVAL;
+			goto out;
+		}
+
+		priv->dest = IPU_CSI_DEST_IDMAC;
+	} else {
+		if (!is_media_entity_v4l2_subdev(remote->entity)) {
+			ret = -EINVAL;
+			goto out;
+		}
+
+		remote_sd = media_entity_to_v4l2_subdev(remote->entity);
+		switch (remote_sd->grp_id) {
+		case IMX_MEDIA_GRP_ID_VDIC:
+			priv->dest = IPU_CSI_DEST_VDIC;
+			break;
+		case IMX_MEDIA_GRP_ID_IC_PRP:
+			priv->dest = IPU_CSI_DEST_IC;
+			break;
+		default:
+			ret = -EINVAL;
+			goto out;
+		}
+	}
+
+	priv->sink = remote->entity;
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int csi_link_validate(struct v4l2_subdev *sd,
+			     struct media_link *link,
+			     struct v4l2_subdev_format *source_fmt,
+			     struct v4l2_subdev_format *sink_fmt)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_of_endpoint *sensor_ep;
+	struct imx_media_subdev *sensor;
+	bool is_csi2;
+	int ret;
+
+	ret = v4l2_subdev_link_validate_default(sd, link,
+						source_fmt, sink_fmt);
+	if (ret)
+		return ret;
+
+	ret = v4l2_subdev_link_validate_frame_interval(link);
+	if (ret)
+		return ret;
+
+	sensor = __imx_media_find_sensor(priv->md, &priv->sd.entity);
+	if (IS_ERR(sensor)) {
+		v4l2_err(&priv->sd, "no sensor attached\n");
+		return PTR_ERR(priv->sensor);
+	}
+
+	mutex_lock(&priv->lock);
+
+	priv->sensor = sensor;
+	sensor_ep = &priv->sensor->sensor_ep;
+
+	is_csi2 = (sensor_ep->bus_type == V4L2_MBUS_CSI2);
+
+	if (is_csi2) {
+		int vc_num = 0;
+		/*
+		 * NOTE! It seems the virtual channels from the mipi csi-2
+		 * receiver are used only for routing by the video mux's,
+		 * or for hard-wired routing to the CSI's. Once the stream
+		 * enters the CSI's however, they are treated internally
+		 * in the IPU as virtual channel 0.
+		 */
+#if 0
+		mutex_unlock(&priv->lock);
+		vc_num = imx_media_find_mipi_csi2_channel(priv->md,
+							  &priv->sd.entity);
+		if (vc_num < 0)
+			return vc_num;
+		mutex_lock(&priv->lock);
+#endif
+		ipu_csi_set_mipi_datatype(priv->csi, vc_num,
+					  &priv->format_mbus[CSI_SINK_PAD]);
+	}
+
+	/* select either parallel or MIPI-CSI2 as input to CSI */
+	ipu_set_csi_src_mux(priv->ipu, priv->csi_id, is_csi2);
+
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int csi_eof_isr(struct v4l2_subdev *sd, u32 status, bool *handled)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	unsigned long flags;
+
+	spin_lock_irqsave(&priv->irqlock, flags);
+	csi_call_fim(priv);
+	spin_unlock_irqrestore(&priv->irqlock, flags);
+
+	return 0;
+}
+
+static int csi_try_crop(struct csi_priv *priv, struct v4l2_rect *crop,
+			struct imx_media_subdev *sensor)
+{
+	struct v4l2_of_endpoint *sensor_ep;
+	struct v4l2_mbus_framefmt *infmt;
+
+	infmt = &priv->format_mbus[CSI_SINK_PAD];
+	sensor_ep = &sensor->sensor_ep;
+
+	crop->width = min_t(__u32, infmt->width, crop->width);
+	if (crop->left + crop->width > infmt->width)
+		crop->left = infmt->width - crop->width;
+	/* adjust crop left/width to h/w alignment restrictions */
+	crop->left &= ~0x3;
+	crop->width &= ~0x7;
+
+	/*
+	 * FIXME: not sure why yet, but on interlaced bt.656,
+	 * changing the vertical cropping causes loss of vertical
+	 * sync, so fix it to NTSC/PAL active lines. NTSC contains
+	 * 2 extra lines of active video that need to be cropped.
+	 */
+	if (sensor_ep->bus_type == V4L2_MBUS_BT656 &&
+	    (V4L2_FIELD_HAS_BOTH(infmt->field) ||
+	     infmt->field == V4L2_FIELD_ALTERNATE)) {
+		crop->height = infmt->height;
+		crop->top = (infmt->height == 480) ? 2 : 0;
+	} else {
+		crop->height = min_t(__u32, infmt->height, crop->height);
+		if (crop->top + crop->height > infmt->height)
+			crop->top = infmt->height - crop->height;
+	}
+
+	return 0;
+}
+
+static int csi_enum_mbus_code(struct v4l2_subdev *sd,
+			      struct v4l2_subdev_pad_config *cfg,
+			      struct v4l2_subdev_mbus_code_enum *code)
+{
+	if (code->pad >= CSI_NUM_PADS)
+		return -EINVAL;
+
+	if (code->pad == CSI_SRC_PAD_DIRECT)
+		return imx_media_enum_ipu_format(NULL, &code->code,
+						 code->index, true);
+
+	return imx_media_enum_format(NULL, &code->code, code->index,
+				     true, false);
+}
+
+static int csi_get_fmt(struct v4l2_subdev *sd,
+		       struct v4l2_subdev_pad_config *cfg,
+		       struct v4l2_subdev_format *sdformat)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+
+	if (sdformat->pad >= CSI_NUM_PADS)
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	sdformat->format = priv->format_mbus[sdformat->pad];
+
+	mutex_unlock(&priv->lock);
+
+	return 0;
+}
+
+static int csi_set_fmt(struct v4l2_subdev *sd,
+		       struct v4l2_subdev_pad_config *cfg,
+		       struct v4l2_subdev_format *sdformat)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	const struct imx_media_pixfmt *cc, *incc;
+	struct v4l2_mbus_framefmt *infmt;
+	struct imx_media_subdev *sensor;
+	struct v4l2_rect crop;
+	int ret = 0;
+	u32 code;
+
+	if (sdformat->pad >= CSI_NUM_PADS)
+		return -EINVAL;
+
+	sensor = imx_media_find_sensor(priv->md, &priv->sd.entity);
+	if (IS_ERR(sensor)) {
+		v4l2_err(&priv->sd, "no sensor attached\n");
+		return PTR_ERR(sensor);
+	}
+
+	mutex_lock(&priv->lock);
+
+	if (priv->stream_on) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	infmt = &priv->format_mbus[CSI_SINK_PAD];
+
+	v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
+			      W_ALIGN, &sdformat->format.height,
+			      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
+
+	switch (sdformat->pad) {
+	case CSI_SRC_PAD_DIRECT:
+	case CSI_SRC_PAD_IDMAC:
+		crop.left = priv->crop.left;
+		crop.top = priv->crop.top;
+		crop.width = sdformat->format.width;
+		crop.height = sdformat->format.height;
+		ret = csi_try_crop(priv, &crop, sensor);
+		if (ret)
+			goto out;
+		sdformat->format.width = crop.width;
+		sdformat->format.height = crop.height;
+
+		if (sdformat->pad == CSI_SRC_PAD_IDMAC) {
+			cc = imx_media_find_format(0, sdformat->format.code,
+						   true, false);
+			if (!cc) {
+				imx_media_enum_format(NULL, &code, 0,
+						      true, false);
+				cc = imx_media_find_format(0, code,
+							   true, false);
+				sdformat->format.code = cc->codes[0];
+			}
+
+			incc = priv->cc[CSI_SINK_PAD];
+			if (cc->cs != incc->cs) {
+				sdformat->format.code = infmt->code;
+				cc = imx_media_find_format(
+					0, sdformat->format.code,
+					true, false);
+			}
+
+			if (sdformat->format.field != V4L2_FIELD_NONE)
+				sdformat->format.field = infmt->field;
+		} else {
+			cc = imx_media_find_ipu_format(0, sdformat->format.code,
+						       true);
+			if (!cc) {
+				imx_media_enum_ipu_format(NULL, &code, 0, true);
+				cc = imx_media_find_ipu_format(0, code, true);
+				sdformat->format.code = cc->codes[0];
+			}
+
+			sdformat->format.field = infmt->field;
+		}
+
+		/*
+		 * translate V4L2_FIELD_ALTERNATE to SEQ_TB or SEQ_BT
+		 * depending on input height (assume NTSC top-bottom
+		 * order if 480 lines, otherwise PAL bottom-top order).
+		 */
+		if (sdformat->format.field == V4L2_FIELD_ALTERNATE) {
+			sdformat->format.field =  (infmt->height == 480) ?
+				V4L2_FIELD_SEQ_TB : V4L2_FIELD_SEQ_BT;
+		}
+		break;
+	case CSI_SINK_PAD:
+		cc = imx_media_find_format(0, sdformat->format.code,
+					   true, false);
+		if (!cc) {
+			imx_media_enum_format(NULL, &code, 0, true, false);
+			cc = imx_media_find_format(0, code, true, false);
+			sdformat->format.code = cc->codes[0];
+		}
+		break;
+	default:
+		ret = -EINVAL;
+		goto out;
+	}
+
+	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
+		cfg->try_fmt = sdformat->format;
+	} else {
+		priv->format_mbus[sdformat->pad] = sdformat->format;
+		priv->cc[sdformat->pad] = cc;
+		/* Update the crop window if this is an output pad  */
+		if (sdformat->pad == CSI_SRC_PAD_DIRECT ||
+		    sdformat->pad == CSI_SRC_PAD_IDMAC)
+			priv->crop = crop;
+	}
+
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int csi_get_selection(struct v4l2_subdev *sd,
+			     struct v4l2_subdev_pad_config *cfg,
+			     struct v4l2_subdev_selection *sel)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_mbus_framefmt *infmt;
+	int ret = 0;
+
+	if (sel->pad >= CSI_NUM_PADS || sel->pad == CSI_SINK_PAD)
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	infmt = &priv->format_mbus[CSI_SINK_PAD];
+
+	switch (sel->target) {
+	case V4L2_SEL_TGT_CROP_BOUNDS:
+		sel->r.left = 0;
+		sel->r.top = 0;
+		sel->r.width = infmt->width;
+		sel->r.height = infmt->height;
+		break;
+	case V4L2_SEL_TGT_CROP:
+		sel->r = priv->crop;
+		break;
+	default:
+		ret = -EINVAL;
+	}
+
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int csi_set_selection(struct v4l2_subdev *sd,
+			     struct v4l2_subdev_pad_config *cfg,
+			     struct v4l2_subdev_selection *sel)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_mbus_framefmt *outfmt;
+	struct imx_media_subdev *sensor;
+	int ret = 0;
+
+	if (sel->pad >= CSI_NUM_PADS ||
+	    sel->pad == CSI_SINK_PAD ||
+	    sel->target != V4L2_SEL_TGT_CROP)
+		return -EINVAL;
+
+	sensor = imx_media_find_sensor(priv->md, &priv->sd.entity);
+	if (IS_ERR(sensor)) {
+		v4l2_err(&priv->sd, "no sensor attached\n");
+		return PTR_ERR(sensor);
+	}
+
+	mutex_lock(&priv->lock);
+
+	if (priv->stream_on) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	/*
+	 * Modifying the crop rectangle always changes the format on the source
+	 * pad. If the KEEP_CONFIG flag is set, just return the current crop
+	 * rectangle.
+	 */
+	if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
+		sel->r = priv->crop;
+		if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
+			cfg->try_crop = sel->r;
+		goto out;
+	}
+
+	outfmt = &priv->format_mbus[sel->pad];
+
+	ret = csi_try_crop(priv, &sel->r, sensor);
+	if (ret)
+		goto out;
+
+	if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
+		cfg->try_crop = sel->r;
+	} else {
+		priv->crop = sel->r;
+		/* Update the source format */
+		outfmt->width = sel->r.width;
+		outfmt->height = sel->r.height;
+	}
+
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int csi_subscribe_event(struct v4l2_subdev *sd, struct v4l2_fh *fh,
+			       struct v4l2_event_subscription *sub)
+{
+	if (sub->type != V4L2_EVENT_NEW_FRAME_BEFORE_EOF &&
+	    sub->type != V4L2_EVENT_FRAME_INTERVAL_ERROR)
+		return -EINVAL;
+	if (sub->id != 0)
+		return -EINVAL;
+
+	return v4l2_event_subscribe(fh, sub, 0, NULL);
+}
+
+static int csi_unsubscribe_event(struct v4l2_subdev *sd, struct v4l2_fh *fh,
+				 struct v4l2_event_subscription *sub)
+{
+	return v4l2_event_unsubscribe(fh, sub);
+}
+
+/*
+ * retrieve our pads parsed from the OF graph by the media device
+ */
+static int csi_registered(struct v4l2_subdev *sd)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	int i, ret;
+	u32 code;
+
+	/* get media device */
+	priv->md = dev_get_drvdata(sd->v4l2_dev->dev);
+
+	/* get handle to IPU CSI */
+	priv->csi = ipu_csi_get(priv->ipu, priv->csi_id);
+	if (IS_ERR(priv->csi)) {
+		v4l2_err(&priv->sd, "failed to get CSI%d\n", priv->csi_id);
+		return PTR_ERR(priv->csi);
+	}
+
+	for (i = 0; i < CSI_NUM_PADS; i++) {
+		priv->pad[i].flags = (i == CSI_SINK_PAD) ?
+			MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
+
+		code = 0;
+		if (i == CSI_SRC_PAD_DIRECT)
+			imx_media_enum_ipu_format(NULL, &code, 0, true);
+
+		/* set a default mbus format  */
+		ret = imx_media_init_mbus_fmt(&priv->format_mbus[i],
+					      640, 480, code, V4L2_FIELD_NONE,
+					      &priv->cc[i]);
+		if (ret)
+			goto put_csi;
+	}
+
+	priv->fim = imx_media_fim_init(&priv->sd);
+	if (IS_ERR(priv->fim)) {
+		ret = PTR_ERR(priv->fim);
+		goto put_csi;
+	}
+
+	ret = media_entity_pads_init(&sd->entity, CSI_NUM_PADS, priv->pad);
+	if (ret)
+		goto free_fim;
+
+	ret = imx_media_capture_device_register(priv->vdev);
+	if (ret)
+		goto free_fim;
+
+	return 0;
+
+free_fim:
+	if (priv->fim)
+		imx_media_fim_free(priv->fim);
+put_csi:
+	ipu_csi_put(priv->csi);
+	return ret;
+}
+
+static void csi_unregistered(struct v4l2_subdev *sd)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+
+	imx_media_capture_device_unregister(priv->vdev);
+
+	if (priv->fim)
+		imx_media_fim_free(priv->fim);
+
+	if (!IS_ERR_OR_NULL(priv->csi))
+		ipu_csi_put(priv->csi);
+}
+
+static struct media_entity_operations csi_entity_ops = {
+	.link_setup = csi_link_setup,
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static struct v4l2_subdev_core_ops csi_core_ops = {
+	.s_power = csi_s_power,
+	.interrupt_service_routine = csi_eof_isr,
+	.subscribe_event = csi_subscribe_event,
+	.unsubscribe_event = csi_unsubscribe_event,
+};
+
+static struct v4l2_subdev_video_ops csi_video_ops = {
+	.s_stream = csi_s_stream,
+};
+
+static struct v4l2_subdev_pad_ops csi_pad_ops = {
+	.enum_mbus_code = csi_enum_mbus_code,
+	.get_fmt = csi_get_fmt,
+	.set_fmt = csi_set_fmt,
+	.get_selection = csi_get_selection,
+	.set_selection = csi_set_selection,
+	.link_validate = csi_link_validate,
+};
+
+static struct v4l2_subdev_ops csi_subdev_ops = {
+	.core = &csi_core_ops,
+	.video = &csi_video_ops,
+	.pad = &csi_pad_ops,
+};
+
+static struct v4l2_subdev_internal_ops csi_internal_ops = {
+	.registered = csi_registered,
+	.unregistered = csi_unregistered,
+};
+
+static int imx_csi_probe(struct platform_device *pdev)
+{
+	struct ipu_client_platformdata *pdata;
+	struct pinctrl *pinctrl;
+	struct csi_priv *priv;
+	int ret;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, &priv->sd);
+	priv->dev = &pdev->dev;
+
+	ret = dma_set_coherent_mask(priv->dev, DMA_BIT_MASK(32));
+	if (ret)
+		return ret;
+
+	/* get parent IPU */
+	priv->ipu = dev_get_drvdata(priv->dev->parent);
+
+	/* get our CSI id */
+	pdata = priv->dev->platform_data;
+	priv->csi_id = pdata->csi;
+	priv->smfc_id = (priv->csi_id == 0) ? 0 : 2;
+
+	init_timer(&priv->eof_timeout_timer);
+	priv->eof_timeout_timer.data = (unsigned long)priv;
+	priv->eof_timeout_timer.function = csi_idmac_eof_timeout;
+	spin_lock_init(&priv->irqlock);
+
+	v4l2_subdev_init(&priv->sd, &csi_subdev_ops);
+	v4l2_set_subdevdata(&priv->sd, priv);
+	priv->sd.internal_ops = &csi_internal_ops;
+	priv->sd.entity.ops = &csi_entity_ops;
+	priv->sd.entity.function = MEDIA_ENT_F_PROC_VIDEO_PIXEL_FORMATTER;
+	priv->sd.dev = &pdev->dev;
+	priv->sd.of_node = pdata->of_node;
+	priv->sd.owner = THIS_MODULE;
+	priv->sd.flags = V4L2_SUBDEV_FL_HAS_DEVNODE | V4L2_SUBDEV_FL_HAS_EVENTS;
+	priv->sd.grp_id = priv->csi_id ?
+		IMX_MEDIA_GRP_ID_CSI1 : IMX_MEDIA_GRP_ID_CSI0;
+	imx_media_grp_id_to_sd_name(priv->sd.name, sizeof(priv->sd.name),
+				    priv->sd.grp_id, ipu_get_num(priv->ipu));
+
+	priv->vdev = imx_media_capture_device_init(&priv->sd,
+						   CSI_SRC_PAD_IDMAC);
+	if (IS_ERR(priv->vdev))
+		return PTR_ERR(priv->vdev);
+
+	v4l2_ctrl_handler_init(&priv->ctrl_hdlr, 0);
+	priv->sd.ctrl_handler = &priv->ctrl_hdlr;
+
+	/*
+	 * The IPUv3 driver did not assign an of_node to this
+	 * device. As a result, pinctrl does not automatically
+	 * configure our pin groups, so we need to do that manually
+	 * here, after setting this device's of_node.
+	 */
+	priv->dev->of_node = pdata->of_node;
+	pinctrl = devm_pinctrl_get_select_default(priv->dev);
+
+	mutex_init(&priv->lock);
+
+	ret = v4l2_async_register_subdev(&priv->sd);
+	if (ret)
+		goto free;
+
+	return 0;
+free:
+	v4l2_ctrl_handler_free(&priv->ctrl_hdlr);
+	mutex_destroy(&priv->lock);
+	imx_media_capture_device_remove(priv->vdev);
+	return ret;
+}
+
+static int imx_csi_remove(struct platform_device *pdev)
+{
+	struct v4l2_subdev *sd = platform_get_drvdata(pdev);
+	struct csi_priv *priv = sd_to_dev(sd);
+
+	v4l2_ctrl_handler_free(&priv->ctrl_hdlr);
+	mutex_destroy(&priv->lock);
+	imx_media_capture_device_remove(priv->vdev);
+	v4l2_async_unregister_subdev(sd);
+	media_entity_cleanup(&sd->entity);
+
+	return 0;
+}
+
+static const struct platform_device_id imx_csi_ids[] = {
+	{ .name = "imx-ipuv3-csi" },
+	{ },
+};
+MODULE_DEVICE_TABLE(platform, imx_csi_ids);
+
+static struct platform_driver imx_csi_driver = {
+	.probe = imx_csi_probe,
+	.remove = imx_csi_remove,
+	.id_table = imx_csi_ids,
+	.driver = {
+		.name = "imx-ipuv3-csi",
+	},
+};
+module_platform_driver(imx_csi_driver);
+
+MODULE_DESCRIPTION("i.MX CSI subdev driver");
+MODULE_AUTHOR("Steve Longerbeam <steve_longerbeam@mentor.com>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:imx-ipuv3-csi");
-- 
2.7.4

[PATCH v5 25/39] media: imx: Add CSI subdev driver

[Steve Longerbeam]

This is a media entity subdevice for the i.MX Camera
Sensor Interface module.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/Kconfig         |   14 +
 drivers/staging/media/imx/Makefile        |    2 +
 drivers/staging/media/imx/imx-media-csi.c | 1311 +++++++++++++++++++++++++++++
 3 files changed, 1327 insertions(+)
 create mode 100644 drivers/staging/media/imx/imx-media-csi.c

diff --git a/drivers/staging/media/imx/Kconfig b/drivers/staging/media/imx/Kconfig
index 62a3c34..e27ad6d 100644
--- a/drivers/staging/media/imx/Kconfig
+++ b/drivers/staging/media/imx/Kconfig
@@ -4,3 +4,17 @@ config VIDEO_IMX_MEDIA
 	---help---
 	  Say yes here to enable support for video4linux media controller
 	  driver for the i.MX5/6 SOC.
+
+if VIDEO_IMX_MEDIA
+menu "i.MX5/6 Media Sub devices"
+
+config VIDEO_IMX_CSI
+	tristate "i.MX5/6 Camera Sensor Interface driver"
+	depends on VIDEO_IMX_MEDIA && VIDEO_DEV && I2C
+	select VIDEOBUF2_DMA_CONTIG
+	default y
+	---help---
+	  A video4linux camera sensor interface driver for i.MX5/6.
+
+endmenu
+endif
diff --git a/drivers/staging/media/imx/Makefile b/drivers/staging/media/imx/Makefile
index 4606a3a..c054490 100644
--- a/drivers/staging/media/imx/Makefile
+++ b/drivers/staging/media/imx/Makefile
@@ -4,3 +4,5 @@ imx-media-common-objs := imx-media-utils.o imx-media-fim.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-common.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-capture.o
+
+obj-$(CONFIG_VIDEO_IMX_CSI) += imx-media-csi.o
diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
new file mode 100644
index 0000000..ab78ff7
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -0,0 +1,1311 @@
+/*
+ * V4L2 Capture CSI Subdev for Freescale i.MX5/6 SOC
+ *
+ * Copyright (c) 2014-2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-mc.h>
+#include <media/v4l2-of.h>
+#include <media/v4l2-subdev.h>
+#include <media/videobuf2-dma-contig.h>
+#include <video/imx-ipu-v3.h>
+#include <media/imx.h>
+#include "imx-media.h"
+
+/*
+ * Min/Max supported width and heights.
+ *
+ * We allow planar output, so we have to align width by 16 pixels
+ * to meet IDMAC alignment requirements.
+ *
+ * TODO: move this into pad format negotiation, if capture device
+ * has not requested planar formats, we should allow 8 pixel
+ * alignment.
+ */
+#define MIN_W       176
+#define MIN_H       144
+#define MAX_W      4096
+#define MAX_H      4096
+#define W_ALIGN    4 /* multiple of 16 pixels */
+#define H_ALIGN    1 /* multiple of 2 lines */
+#define S_ALIGN    1 /* multiple of 2 */
+
+struct csi_priv {
+	struct device *dev;
+	struct ipu_soc *ipu;
+	struct imx_media_dev *md;
+	struct v4l2_subdev sd;
+	struct media_pad pad[CSI_NUM_PADS];
+	/* the video device at IDMAC output pad */
+	struct imx_media_video_dev *vdev;
+	struct imx_media_fim *fim;
+	int csi_id;
+	int smfc_id;
+
+	/* lock to protect all members below */
+	struct mutex lock;
+
+	int active_output_pad;
+
+	struct ipuv3_channel *idmac_ch;
+	struct ipu_smfc *smfc;
+	struct ipu_csi *csi;
+
+	struct v4l2_mbus_framefmt format_mbus[CSI_NUM_PADS];
+	const struct imx_media_pixfmt *cc[CSI_NUM_PADS];
+	struct v4l2_rect crop;
+
+	/* active vb2 buffers to send to video dev sink */
+	struct imx_media_buffer *active_vb2_buf[2];
+	struct imx_media_dma_buf underrun_buf;
+
+	int ipu_buf_num;  /* ipu double buffer index: 0-1 */
+
+	/* the sink for the captured frames */
+	struct media_entity *sink;
+	enum ipu_csi_dest dest;
+	/* the source subdev */
+	struct v4l2_subdev *src_sd;
+
+	/* the mipi virtual channel number at link validate */
+	int vc_num;
+
+	/* the attached sensor at stream on */
+	struct imx_media_subdev *sensor;
+
+	spinlock_t irqlock; /* protect eof_irq handler */
+	struct timer_list eof_timeout_timer;
+	int eof_irq;
+	int nfb4eof_irq;
+
+	struct v4l2_ctrl_handler ctrl_hdlr;
+
+	int power_count; /* power counter */
+	bool stream_on;  /* streaming is on */
+	bool last_eof;   /* waiting for last EOF at stream off */
+	struct completion last_eof_comp;
+};
+
+static inline struct csi_priv *sd_to_dev(struct v4l2_subdev *sdev)
+{
+	return container_of(sdev, struct csi_priv, sd);
+}
+
+static void csi_idmac_put_ipu_resources(struct csi_priv *priv)
+{
+	if (!IS_ERR_OR_NULL(priv->idmac_ch))
+		ipu_idmac_put(priv->idmac_ch);
+	priv->idmac_ch = NULL;
+
+	if (!IS_ERR_OR_NULL(priv->smfc))
+		ipu_smfc_put(priv->smfc);
+	priv->smfc = NULL;
+}
+
+static int csi_idmac_get_ipu_resources(struct csi_priv *priv)
+{
+	int ch_num, ret;
+
+	ch_num = IPUV3_CHANNEL_CSI0 + priv->smfc_id;
+
+	priv->smfc = ipu_smfc_get(priv->ipu, ch_num);
+	if (IS_ERR(priv->smfc)) {
+		v4l2_err(&priv->sd, "failed to get SMFC\n");
+		ret = PTR_ERR(priv->smfc);
+		goto out;
+	}
+
+	priv->idmac_ch = ipu_idmac_get(priv->ipu, ch_num);
+	if (IS_ERR(priv->idmac_ch)) {
+		v4l2_err(&priv->sd, "could not get IDMAC channel %u\n",
+			 ch_num);
+		ret = PTR_ERR(priv->idmac_ch);
+		goto out;
+	}
+
+	return 0;
+out:
+	csi_idmac_put_ipu_resources(priv);
+	return ret;
+}
+
+static void csi_vb2_buf_done(struct csi_priv *priv)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct imx_media_buffer *done, *next;
+	struct vb2_buffer *vb;
+	dma_addr_t phys;
+
+	done = priv->active_vb2_buf[priv->ipu_buf_num];
+	if (done) {
+		vb = &done->vbuf.vb2_buf;
+		vb->timestamp = ktime_get_ns();
+		vb2_buffer_done(vb, VB2_BUF_STATE_DONE);
+	}
+
+	/* get next queued buffer */
+	next = imx_media_capture_device_next_buf(vdev);
+	if (next) {
+		phys = vb2_dma_contig_plane_dma_addr(&next->vbuf.vb2_buf, 0);
+		priv->active_vb2_buf[priv->ipu_buf_num] = next;
+	} else {
+		phys = priv->underrun_buf.phys;
+		priv->active_vb2_buf[priv->ipu_buf_num] = NULL;
+	}
+
+	if (ipu_idmac_buffer_is_ready(priv->idmac_ch, priv->ipu_buf_num))
+		ipu_idmac_clear_buffer(priv->idmac_ch, priv->ipu_buf_num);
+
+	ipu_cpmem_set_buffer(priv->idmac_ch, priv->ipu_buf_num, phys);
+}
+
+static void csi_call_fim(struct csi_priv *priv)
+{
+	if (priv->fim) {
+		struct timespec cur_ts;
+
+		ktime_get_ts(&cur_ts);
+		/* call frame interval monitor */
+		imx_media_fim_eof_monitor(priv->fim, &cur_ts);
+	}
+}
+
+static irqreturn_t csi_idmac_eof_interrupt(int irq, void *dev_id)
+{
+	struct csi_priv *priv = dev_id;
+
+	spin_lock(&priv->irqlock);
+
+	if (priv->last_eof) {
+		complete(&priv->last_eof_comp);
+		priv->last_eof = false;
+		goto unlock;
+	}
+
+	csi_call_fim(priv);
+
+	csi_vb2_buf_done(priv);
+
+	/* select new IPU buf */
+	ipu_idmac_select_buffer(priv->idmac_ch, priv->ipu_buf_num);
+	/* toggle IPU double-buffer index */
+	priv->ipu_buf_num ^= 1;
+
+	/* bump the EOF timeout timer */
+	mod_timer(&priv->eof_timeout_timer,
+		  jiffies + msecs_to_jiffies(IMX_MEDIA_EOF_TIMEOUT));
+
+unlock:
+	spin_unlock(&priv->irqlock);
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t csi_idmac_nfb4eof_interrupt(int irq, void *dev_id)
+{
+	struct csi_priv *priv = dev_id;
+	static const struct v4l2_event ev = {
+		.type = V4L2_EVENT_NEW_FRAME_BEFORE_EOF,
+	};
+
+	v4l2_err(&priv->sd, "NFB4EOF\n");
+
+	v4l2_subdev_notify_event(&priv->sd, &ev);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * EOF timeout timer function. This is an unrecoverable condition
+ * without a stream restart.
+ */
+static void csi_idmac_eof_timeout(unsigned long data)
+{
+	struct csi_priv *priv = (struct csi_priv *)data;
+	struct imx_media_video_dev *vdev = priv->vdev;
+
+	v4l2_err(&priv->sd, "EOF timeout\n");
+
+	/* signal a fatal error to capture device */
+	imx_media_capture_device_error(vdev);
+}
+
+static void csi_idmac_setup_vb2_buf(struct csi_priv *priv, dma_addr_t *phys)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct imx_media_buffer *buf;
+	int i;
+
+	for (i = 0; i < 2; i++) {
+		buf = imx_media_capture_device_next_buf(vdev);
+		priv->active_vb2_buf[i] = buf;
+		phys[i] = vb2_dma_contig_plane_dma_addr(&buf->vbuf.vb2_buf, 0);
+	}
+}
+
+static void csi_idmac_unsetup_vb2_buf(struct csi_priv *priv,
+				      enum vb2_buffer_state return_state)
+{
+	struct imx_media_buffer *buf;
+	int i;
+
+	/* return any remaining active frames with error */
+	for (i = 0; i < 2; i++) {
+		buf = priv->active_vb2_buf[i];
+		if (buf) {
+			struct vb2_buffer *vb = &buf->vbuf.vb2_buf;
+
+			vb->timestamp = ktime_get_ns();
+			vb2_buffer_done(vb, return_state);
+		}
+	}
+}
+
+/* init the SMFC IDMAC channel */
+static int csi_idmac_setup_channel(struct csi_priv *priv)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct v4l2_of_endpoint *sensor_ep;
+	struct v4l2_mbus_framefmt *infmt;
+	unsigned int burst_size;
+	struct ipu_image image;
+	dma_addr_t phys[2];
+	bool passthrough;
+	int ret;
+
+	infmt = &priv->format_mbus[CSI_SINK_PAD];
+	sensor_ep = &priv->sensor->sensor_ep;
+
+	ipu_cpmem_zero(priv->idmac_ch);
+
+	memset(&image, 0, sizeof(image));
+	image.pix = vdev->fmt.fmt.pix;
+	image.rect.width = image.pix.width;
+	image.rect.height = image.pix.height;
+
+	csi_idmac_setup_vb2_buf(priv, phys);
+
+	image.phys0 = phys[0];
+	image.phys1 = phys[1];
+
+	ret = ipu_cpmem_set_image(priv->idmac_ch, &image);
+	if (ret)
+		return ret;
+
+	burst_size = (image.pix.width & 0xf) ? 8 : 16;
+
+	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
+
+	/*
+	 * If the sensor uses 16-bit parallel CSI bus, we must handle
+	 * the data internally in the IPU as 16-bit generic, aka
+	 * passthrough mode.
+	 */
+	passthrough = (sensor_ep->bus_type != V4L2_MBUS_CSI2 &&
+		       sensor_ep->bus.parallel.bus_width >= 16);
+
+	if (passthrough)
+		ipu_cpmem_set_format_passthrough(priv->idmac_ch, 16);
+
+	/*
+	 * Set the channel for the direct CSI-->memory via SMFC
+	 * use-case to very high priority, by enabling the watermark
+	 * signal in the SMFC, enabling WM in the channel, and setting
+	 * the channel priority to high.
+	 *
+	 * Refer to the i.mx6 rev. D TRM Table 36-8: Calculated priority
+	 * value.
+	 *
+	 * The WM's are set very low by intention here to ensure that
+	 * the SMFC FIFOs do not overflow.
+	 */
+	ipu_smfc_set_watermark(priv->smfc, 0x02, 0x01);
+	ipu_cpmem_set_high_priority(priv->idmac_ch);
+	ipu_idmac_enable_watermark(priv->idmac_ch, true);
+	ipu_cpmem_set_axi_id(priv->idmac_ch, 0);
+	ipu_idmac_lock_enable(priv->idmac_ch, 8);
+
+	burst_size = ipu_cpmem_get_burstsize(priv->idmac_ch);
+	burst_size = passthrough ?
+		(burst_size >> 3) - 1 : (burst_size >> 2) - 1;
+
+	ipu_smfc_set_burstsize(priv->smfc, burst_size);
+
+	if (image.pix.field == V4L2_FIELD_NONE &&
+	    V4L2_FIELD_HAS_BOTH(infmt->field))
+		ipu_cpmem_interlaced_scan(priv->idmac_ch,
+					  image.pix.bytesperline);
+
+	ipu_idmac_set_double_buffer(priv->idmac_ch, true);
+
+	return 0;
+}
+
+static void csi_idmac_unsetup(struct csi_priv *priv,
+			      enum vb2_buffer_state state)
+{
+	ipu_idmac_disable_channel(priv->idmac_ch);
+	ipu_smfc_disable(priv->smfc);
+
+	csi_idmac_unsetup_vb2_buf(priv, state);
+}
+
+static int csi_idmac_setup(struct csi_priv *priv)
+{
+	int ret;
+
+	ret = csi_idmac_setup_channel(priv);
+	if (ret)
+		return ret;
+
+	ipu_cpmem_dump(priv->idmac_ch);
+	ipu_dump(priv->ipu);
+
+	ipu_smfc_enable(priv->smfc);
+
+	/* set buffers ready */
+	ipu_idmac_select_buffer(priv->idmac_ch, 0);
+	ipu_idmac_select_buffer(priv->idmac_ch, 1);
+
+	/* enable the channels */
+	ipu_idmac_enable_channel(priv->idmac_ch);
+
+	return 0;
+}
+
+static int csi_idmac_start(struct csi_priv *priv)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct v4l2_pix_format *outfmt;
+	int ret;
+
+	ret = csi_idmac_get_ipu_resources(priv);
+	if (ret)
+		return ret;
+
+	ipu_smfc_map_channel(priv->smfc, priv->csi_id, priv->vc_num);
+
+	outfmt = &vdev->fmt.fmt.pix;
+
+	ret = imx_media_alloc_dma_buf(priv->md, &priv->underrun_buf,
+				      outfmt->sizeimage);
+	if (ret)
+		goto out_put_ipu;
+
+	priv->ipu_buf_num = 0;
+
+	/* init EOF completion waitq */
+	init_completion(&priv->last_eof_comp);
+	priv->last_eof = false;
+
+	ret = csi_idmac_setup(priv);
+	if (ret) {
+		v4l2_err(&priv->sd, "csi_idmac_setup failed: %d\n", ret);
+		goto out_free_dma_buf;
+	}
+
+	priv->nfb4eof_irq = ipu_idmac_channel_irq(priv->ipu,
+						 priv->idmac_ch,
+						 IPU_IRQ_NFB4EOF);
+	ret = devm_request_irq(priv->dev, priv->nfb4eof_irq,
+			       csi_idmac_nfb4eof_interrupt, 0,
+			       "imx-smfc-nfb4eof", priv);
+	if (ret) {
+		v4l2_err(&priv->sd,
+			 "Error registering NFB4EOF irq: %d\n", ret);
+		goto out_unsetup;
+	}
+
+	priv->eof_irq = ipu_idmac_channel_irq(priv->ipu, priv->idmac_ch,
+					      IPU_IRQ_EOF);
+
+	ret = devm_request_irq(priv->dev, priv->eof_irq,
+			       csi_idmac_eof_interrupt, 0,
+			       "imx-smfc-eof", priv);
+	if (ret) {
+		v4l2_err(&priv->sd,
+			 "Error registering eof irq: %d\n", ret);
+		goto out_free_nfb4eof_irq;
+	}
+
+	/* start the EOF timeout timer */
+	mod_timer(&priv->eof_timeout_timer,
+		  jiffies + msecs_to_jiffies(IMX_MEDIA_EOF_TIMEOUT));
+
+	return 0;
+
+out_free_nfb4eof_irq:
+	devm_free_irq(priv->dev, priv->nfb4eof_irq, priv);
+out_unsetup:
+	csi_idmac_unsetup(priv, VB2_BUF_STATE_QUEUED);
+out_free_dma_buf:
+	imx_media_free_dma_buf(priv->md, &priv->underrun_buf);
+out_put_ipu:
+	csi_idmac_put_ipu_resources(priv);
+	return ret;
+}
+
+static void csi_idmac_stop(struct csi_priv *priv)
+{
+	unsigned long flags;
+	int ret;
+
+	/* mark next EOF interrupt as the last before stream off */
+	spin_lock_irqsave(&priv->irqlock, flags);
+	priv->last_eof = true;
+	spin_unlock_irqrestore(&priv->irqlock, flags);
+
+	/*
+	 * and then wait for interrupt handler to mark completion.
+	 */
+	ret = wait_for_completion_timeout(
+		&priv->last_eof_comp, msecs_to_jiffies(IMX_MEDIA_EOF_TIMEOUT));
+	if (ret == 0)
+		v4l2_warn(&priv->sd, "wait last EOF timeout\n");
+
+	devm_free_irq(priv->dev, priv->eof_irq, priv);
+	devm_free_irq(priv->dev, priv->nfb4eof_irq, priv);
+
+	csi_idmac_unsetup(priv, VB2_BUF_STATE_ERROR);
+
+	imx_media_free_dma_buf(priv->md, &priv->underrun_buf);
+
+	/* cancel the EOF timeout timer */
+	del_timer_sync(&priv->eof_timeout_timer);
+
+	csi_idmac_put_ipu_resources(priv);
+}
+
+/* Update the CSI whole sensor and active windows */
+static int csi_setup(struct csi_priv *priv)
+{
+	struct v4l2_mbus_framefmt *infmt, *outfmt;
+	struct v4l2_mbus_config sensor_mbus_cfg;
+	struct v4l2_of_endpoint *sensor_ep;
+	struct v4l2_mbus_framefmt if_fmt;
+
+	infmt = &priv->format_mbus[CSI_SINK_PAD];
+	outfmt = &priv->format_mbus[priv->active_output_pad];
+	sensor_ep = &priv->sensor->sensor_ep;
+
+	/* compose mbus_config from sensor endpoint */
+	sensor_mbus_cfg.type = sensor_ep->bus_type;
+	sensor_mbus_cfg.flags = (sensor_ep->bus_type == V4L2_MBUS_CSI2) ?
+		sensor_ep->bus.mipi_csi2.flags :
+		sensor_ep->bus.parallel.flags;
+
+	/*
+	 * we need to pass input sensor frame to CSI interface, but
+	 * with translated field type from output format
+	 */
+	if_fmt = *infmt;
+	if_fmt.field = outfmt->field;
+
+	ipu_csi_set_window(priv->csi, &priv->crop);
+
+	ipu_csi_init_interface(priv->csi, &sensor_mbus_cfg, &if_fmt);
+
+	ipu_csi_set_dest(priv->csi, priv->dest);
+
+	ipu_csi_dump(priv->csi);
+
+	return 0;
+}
+
+static int csi_start(struct csi_priv *priv)
+{
+	int ret;
+
+	if (!priv->sensor) {
+		v4l2_err(&priv->sd, "no sensor attached\n");
+		return -EINVAL;
+	}
+
+	if (priv->dest == IPU_CSI_DEST_IDMAC) {
+		ret = csi_idmac_start(priv);
+		if (ret)
+			return ret;
+	}
+
+	ret = csi_setup(priv);
+	if (ret)
+		goto idmac_stop;
+
+	/* start the frame interval monitor */
+	if (priv->fim) {
+		ret = imx_media_fim_set_stream(priv->fim, priv->sensor, true);
+		if (ret)
+			goto idmac_stop;
+	}
+
+	ret = ipu_csi_enable(priv->csi);
+	if (ret) {
+		v4l2_err(&priv->sd, "CSI enable error: %d\n", ret);
+		goto fim_off;
+	}
+
+	return 0;
+
+fim_off:
+	if (priv->fim)
+		imx_media_fim_set_stream(priv->fim, priv->sensor, false);
+idmac_stop:
+	if (priv->dest == IPU_CSI_DEST_IDMAC)
+		csi_idmac_stop(priv);
+	return ret;
+}
+
+static void csi_stop(struct csi_priv *priv)
+{
+	if (priv->dest == IPU_CSI_DEST_IDMAC)
+		csi_idmac_stop(priv);
+
+	/* stop the frame interval monitor */
+	if (priv->fim)
+		imx_media_fim_set_stream(priv->fim, priv->sensor, false);
+
+	ipu_csi_disable(priv->csi);
+}
+
+/*
+ * V4L2 subdev operations.
+ */
+
+static int csi_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	int ret = 0;
+
+	mutex_lock(&priv->lock);
+
+	if (!priv->src_sd || !priv->sink) {
+		ret = -EPIPE;
+		goto out;
+	}
+
+	dev_dbg(priv->dev, "stream %s\n", enable ? "ON" : "OFF");
+
+	if (enable && !priv->stream_on)
+		ret = csi_start(priv);
+	else if (!enable && priv->stream_on)
+		csi_stop(priv);
+
+	if (!ret)
+		priv->stream_on = enable;
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int csi_s_power(struct v4l2_subdev *sd, int on)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	int ret = 0;
+
+	dev_dbg(priv->dev, "power %s\n", on ? "ON" : "OFF");
+
+	mutex_lock(&priv->lock);
+
+	/*
+	 * If the power count is modified from 0 to != 0 or from != 0 to 0,
+	 * update the power state.
+	 */
+	if (priv->power_count == !on) {
+		if (priv->fim) {
+			ret = imx_media_fim_set_power(priv->fim, on);
+			if (ret)
+				goto out;
+		}
+	}
+
+	/* Update the power count. */
+	priv->power_count += on ? 1 : -1;
+	WARN_ON(priv->power_count < 0);
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int csi_link_setup(struct media_entity *entity,
+			  const struct media_pad *local,
+			  const struct media_pad *remote, u32 flags)
+{
+	struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity);
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_subdev *remote_sd;
+	int ret = 0;
+
+	dev_dbg(priv->dev, "link setup %s -> %s\n", remote->entity->name,
+		local->entity->name);
+
+	mutex_lock(&priv->lock);
+
+	if (local->flags & MEDIA_PAD_FL_SINK) {
+		if (!is_media_entity_v4l2_subdev(remote->entity)) {
+			ret = -EINVAL;
+			goto out;
+		}
+
+		remote_sd = media_entity_to_v4l2_subdev(remote->entity);
+
+		if (flags & MEDIA_LNK_FL_ENABLED) {
+			if (priv->src_sd) {
+				ret = -EBUSY;
+				goto out;
+			}
+			priv->src_sd = remote_sd;
+		} else {
+			priv->src_sd = NULL;
+		}
+
+		goto out;
+	}
+
+	/* this is a source pad */
+
+	if (flags & MEDIA_LNK_FL_ENABLED) {
+		if (priv->sink) {
+			ret = -EBUSY;
+			goto out;
+		}
+	} else {
+		priv->sink = NULL;
+		goto out;
+	}
+
+	/* record which output pad is now active */
+	priv->active_output_pad = local->index;
+
+	/* set CSI destination */
+	if (local->index == CSI_SRC_PAD_IDMAC) {
+		if (!is_media_entity_v4l2_video_device(remote->entity)) {
+			ret = -EINVAL;
+			goto out;
+		}
+
+		priv->dest = IPU_CSI_DEST_IDMAC;
+	} else {
+		if (!is_media_entity_v4l2_subdev(remote->entity)) {
+			ret = -EINVAL;
+			goto out;
+		}
+
+		remote_sd = media_entity_to_v4l2_subdev(remote->entity);
+		switch (remote_sd->grp_id) {
+		case IMX_MEDIA_GRP_ID_VDIC:
+			priv->dest = IPU_CSI_DEST_VDIC;
+			break;
+		case IMX_MEDIA_GRP_ID_IC_PRP:
+			priv->dest = IPU_CSI_DEST_IC;
+			break;
+		default:
+			ret = -EINVAL;
+			goto out;
+		}
+	}
+
+	priv->sink = remote->entity;
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int csi_link_validate(struct v4l2_subdev *sd,
+			     struct media_link *link,
+			     struct v4l2_subdev_format *source_fmt,
+			     struct v4l2_subdev_format *sink_fmt)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_of_endpoint *sensor_ep;
+	struct imx_media_subdev *sensor;
+	bool is_csi2;
+	int ret;
+
+	ret = v4l2_subdev_link_validate_default(sd, link,
+						source_fmt, sink_fmt);
+	if (ret)
+		return ret;
+
+	ret = v4l2_subdev_link_validate_frame_interval(link);
+	if (ret)
+		return ret;
+
+	sensor = __imx_media_find_sensor(priv->md, &priv->sd.entity);
+	if (IS_ERR(sensor)) {
+		v4l2_err(&priv->sd, "no sensor attached\n");
+		return PTR_ERR(priv->sensor);
+	}
+
+	mutex_lock(&priv->lock);
+
+	priv->sensor = sensor;
+	sensor_ep = &priv->sensor->sensor_ep;
+
+	is_csi2 = (sensor_ep->bus_type == V4L2_MBUS_CSI2);
+
+	if (is_csi2) {
+		int vc_num = 0;
+		/*
+		 * NOTE! It seems the virtual channels from the mipi csi-2
+		 * receiver are used only for routing by the video mux's,
+		 * or for hard-wired routing to the CSI's. Once the stream
+		 * enters the CSI's however, they are treated internally
+		 * in the IPU as virtual channel 0.
+		 */
+#if 0
+		mutex_unlock(&priv->lock);
+		vc_num = imx_media_find_mipi_csi2_channel(priv->md,
+							  &priv->sd.entity);
+		if (vc_num < 0)
+			return vc_num;
+		mutex_lock(&priv->lock);
+#endif
+		ipu_csi_set_mipi_datatype(priv->csi, vc_num,
+					  &priv->format_mbus[CSI_SINK_PAD]);
+	}
+
+	/* select either parallel or MIPI-CSI2 as input to CSI */
+	ipu_set_csi_src_mux(priv->ipu, priv->csi_id, is_csi2);
+
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int csi_eof_isr(struct v4l2_subdev *sd, u32 status, bool *handled)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	unsigned long flags;
+
+	spin_lock_irqsave(&priv->irqlock, flags);
+	csi_call_fim(priv);
+	spin_unlock_irqrestore(&priv->irqlock, flags);
+
+	return 0;
+}
+
+static int csi_try_crop(struct csi_priv *priv, struct v4l2_rect *crop,
+			struct imx_media_subdev *sensor)
+{
+	struct v4l2_of_endpoint *sensor_ep;
+	struct v4l2_mbus_framefmt *infmt;
+
+	infmt = &priv->format_mbus[CSI_SINK_PAD];
+	sensor_ep = &sensor->sensor_ep;
+
+	crop->width = min_t(__u32, infmt->width, crop->width);
+	if (crop->left + crop->width > infmt->width)
+		crop->left = infmt->width - crop->width;
+	/* adjust crop left/width to h/w alignment restrictions */
+	crop->left &= ~0x3;
+	crop->width &= ~0x7;
+
+	/*
+	 * FIXME: not sure why yet, but on interlaced bt.656,
+	 * changing the vertical cropping causes loss of vertical
+	 * sync, so fix it to NTSC/PAL active lines. NTSC contains
+	 * 2 extra lines of active video that need to be cropped.
+	 */
+	if (sensor_ep->bus_type == V4L2_MBUS_BT656 &&
+	    (V4L2_FIELD_HAS_BOTH(infmt->field) ||
+	     infmt->field == V4L2_FIELD_ALTERNATE)) {
+		crop->height = infmt->height;
+		crop->top = (infmt->height == 480) ? 2 : 0;
+	} else {
+		crop->height = min_t(__u32, infmt->height, crop->height);
+		if (crop->top + crop->height > infmt->height)
+			crop->top = infmt->height - crop->height;
+	}
+
+	return 0;
+}
+
+static int csi_enum_mbus_code(struct v4l2_subdev *sd,
+			      struct v4l2_subdev_pad_config *cfg,
+			      struct v4l2_subdev_mbus_code_enum *code)
+{
+	if (code->pad >= CSI_NUM_PADS)
+		return -EINVAL;
+
+	if (code->pad == CSI_SRC_PAD_DIRECT)
+		return imx_media_enum_ipu_format(NULL, &code->code,
+						 code->index, true);
+
+	return imx_media_enum_format(NULL, &code->code, code->index,
+				     true, false);
+}
+
+static int csi_get_fmt(struct v4l2_subdev *sd,
+		       struct v4l2_subdev_pad_config *cfg,
+		       struct v4l2_subdev_format *sdformat)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+
+	if (sdformat->pad >= CSI_NUM_PADS)
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	sdformat->format = priv->format_mbus[sdformat->pad];
+
+	mutex_unlock(&priv->lock);
+
+	return 0;
+}
+
+static int csi_set_fmt(struct v4l2_subdev *sd,
+		       struct v4l2_subdev_pad_config *cfg,
+		       struct v4l2_subdev_format *sdformat)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	const struct imx_media_pixfmt *cc, *incc;
+	struct v4l2_mbus_framefmt *infmt;
+	struct imx_media_subdev *sensor;
+	struct v4l2_rect crop;
+	int ret = 0;
+	u32 code;
+
+	if (sdformat->pad >= CSI_NUM_PADS)
+		return -EINVAL;
+
+	sensor = imx_media_find_sensor(priv->md, &priv->sd.entity);
+	if (IS_ERR(sensor)) {
+		v4l2_err(&priv->sd, "no sensor attached\n");
+		return PTR_ERR(sensor);
+	}
+
+	mutex_lock(&priv->lock);
+
+	if (priv->stream_on) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	infmt = &priv->format_mbus[CSI_SINK_PAD];
+
+	v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
+			      W_ALIGN, &sdformat->format.height,
+			      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
+
+	switch (sdformat->pad) {
+	case CSI_SRC_PAD_DIRECT:
+	case CSI_SRC_PAD_IDMAC:
+		crop.left = priv->crop.left;
+		crop.top = priv->crop.top;
+		crop.width = sdformat->format.width;
+		crop.height = sdformat->format.height;
+		ret = csi_try_crop(priv, &crop, sensor);
+		if (ret)
+			goto out;
+		sdformat->format.width = crop.width;
+		sdformat->format.height = crop.height;
+
+		if (sdformat->pad == CSI_SRC_PAD_IDMAC) {
+			cc = imx_media_find_format(0, sdformat->format.code,
+						   true, false);
+			if (!cc) {
+				imx_media_enum_format(NULL, &code, 0,
+						      true, false);
+				cc = imx_media_find_format(0, code,
+							   true, false);
+				sdformat->format.code = cc->codes[0];
+			}
+
+			incc = priv->cc[CSI_SINK_PAD];
+			if (cc->cs != incc->cs) {
+				sdformat->format.code = infmt->code;
+				cc = imx_media_find_format(
+					0, sdformat->format.code,
+					true, false);
+			}
+
+			if (sdformat->format.field != V4L2_FIELD_NONE)
+				sdformat->format.field = infmt->field;
+		} else {
+			cc = imx_media_find_ipu_format(0, sdformat->format.code,
+						       true);
+			if (!cc) {
+				imx_media_enum_ipu_format(NULL, &code, 0, true);
+				cc = imx_media_find_ipu_format(0, code, true);
+				sdformat->format.code = cc->codes[0];
+			}
+
+			sdformat->format.field = infmt->field;
+		}
+
+		/*
+		 * translate V4L2_FIELD_ALTERNATE to SEQ_TB or SEQ_BT
+		 * depending on input height (assume NTSC top-bottom
+		 * order if 480 lines, otherwise PAL bottom-top order).
+		 */
+		if (sdformat->format.field == V4L2_FIELD_ALTERNATE) {
+			sdformat->format.field =  (infmt->height == 480) ?
+				V4L2_FIELD_SEQ_TB : V4L2_FIELD_SEQ_BT;
+		}
+		break;
+	case CSI_SINK_PAD:
+		cc = imx_media_find_format(0, sdformat->format.code,
+					   true, false);
+		if (!cc) {
+			imx_media_enum_format(NULL, &code, 0, true, false);
+			cc = imx_media_find_format(0, code, true, false);
+			sdformat->format.code = cc->codes[0];
+		}
+		break;
+	default:
+		ret = -EINVAL;
+		goto out;
+	}
+
+	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
+		cfg->try_fmt = sdformat->format;
+	} else {
+		priv->format_mbus[sdformat->pad] = sdformat->format;
+		priv->cc[sdformat->pad] = cc;
+		/* Update the crop window if this is an output pad  */
+		if (sdformat->pad == CSI_SRC_PAD_DIRECT ||
+		    sdformat->pad == CSI_SRC_PAD_IDMAC)
+			priv->crop = crop;
+	}
+
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int csi_get_selection(struct v4l2_subdev *sd,
+			     struct v4l2_subdev_pad_config *cfg,
+			     struct v4l2_subdev_selection *sel)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_mbus_framefmt *infmt;
+	int ret = 0;
+
+	if (sel->pad >= CSI_NUM_PADS || sel->pad == CSI_SINK_PAD)
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	infmt = &priv->format_mbus[CSI_SINK_PAD];
+
+	switch (sel->target) {
+	case V4L2_SEL_TGT_CROP_BOUNDS:
+		sel->r.left = 0;
+		sel->r.top = 0;
+		sel->r.width = infmt->width;
+		sel->r.height = infmt->height;
+		break;
+	case V4L2_SEL_TGT_CROP:
+		sel->r = priv->crop;
+		break;
+	default:
+		ret = -EINVAL;
+	}
+
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int csi_set_selection(struct v4l2_subdev *sd,
+			     struct v4l2_subdev_pad_config *cfg,
+			     struct v4l2_subdev_selection *sel)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_mbus_framefmt *outfmt;
+	struct imx_media_subdev *sensor;
+	int ret = 0;
+
+	if (sel->pad >= CSI_NUM_PADS ||
+	    sel->pad == CSI_SINK_PAD ||
+	    sel->target != V4L2_SEL_TGT_CROP)
+		return -EINVAL;
+
+	sensor = imx_media_find_sensor(priv->md, &priv->sd.entity);
+	if (IS_ERR(sensor)) {
+		v4l2_err(&priv->sd, "no sensor attached\n");
+		return PTR_ERR(sensor);
+	}
+
+	mutex_lock(&priv->lock);
+
+	if (priv->stream_on) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	/*
+	 * Modifying the crop rectangle always changes the format on the source
+	 * pad. If the KEEP_CONFIG flag is set, just return the current crop
+	 * rectangle.
+	 */
+	if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
+		sel->r = priv->crop;
+		if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
+			cfg->try_crop = sel->r;
+		goto out;
+	}
+
+	outfmt = &priv->format_mbus[sel->pad];
+
+	ret = csi_try_crop(priv, &sel->r, sensor);
+	if (ret)
+		goto out;
+
+	if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
+		cfg->try_crop = sel->r;
+	} else {
+		priv->crop = sel->r;
+		/* Update the source format */
+		outfmt->width = sel->r.width;
+		outfmt->height = sel->r.height;
+	}
+
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int csi_subscribe_event(struct v4l2_subdev *sd, struct v4l2_fh *fh,
+			       struct v4l2_event_subscription *sub)
+{
+	if (sub->type != V4L2_EVENT_NEW_FRAME_BEFORE_EOF &&
+	    sub->type != V4L2_EVENT_FRAME_INTERVAL_ERROR)
+		return -EINVAL;
+	if (sub->id != 0)
+		return -EINVAL;
+
+	return v4l2_event_subscribe(fh, sub, 0, NULL);
+}
+
+static int csi_unsubscribe_event(struct v4l2_subdev *sd, struct v4l2_fh *fh,
+				 struct v4l2_event_subscription *sub)
+{
+	return v4l2_event_unsubscribe(fh, sub);
+}
+
+/*
+ * retrieve our pads parsed from the OF graph by the media device
+ */
+static int csi_registered(struct v4l2_subdev *sd)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	int i, ret;
+	u32 code;
+
+	/* get media device */
+	priv->md = dev_get_drvdata(sd->v4l2_dev->dev);
+
+	/* get handle to IPU CSI */
+	priv->csi = ipu_csi_get(priv->ipu, priv->csi_id);
+	if (IS_ERR(priv->csi)) {
+		v4l2_err(&priv->sd, "failed to get CSI%d\n", priv->csi_id);
+		return PTR_ERR(priv->csi);
+	}
+
+	for (i = 0; i < CSI_NUM_PADS; i++) {
+		priv->pad[i].flags = (i == CSI_SINK_PAD) ?
+			MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
+
+		code = 0;
+		if (i == CSI_SRC_PAD_DIRECT)
+			imx_media_enum_ipu_format(NULL, &code, 0, true);
+
+		/* set a default mbus format  */
+		ret = imx_media_init_mbus_fmt(&priv->format_mbus[i],
+					      640, 480, code, V4L2_FIELD_NONE,
+					      &priv->cc[i]);
+		if (ret)
+			goto put_csi;
+	}
+
+	priv->fim = imx_media_fim_init(&priv->sd);
+	if (IS_ERR(priv->fim)) {
+		ret = PTR_ERR(priv->fim);
+		goto put_csi;
+	}
+
+	ret = media_entity_pads_init(&sd->entity, CSI_NUM_PADS, priv->pad);
+	if (ret)
+		goto free_fim;
+
+	ret = imx_media_capture_device_register(priv->vdev);
+	if (ret)
+		goto free_fim;
+
+	return 0;
+
+free_fim:
+	if (priv->fim)
+		imx_media_fim_free(priv->fim);
+put_csi:
+	ipu_csi_put(priv->csi);
+	return ret;
+}
+
+static void csi_unregistered(struct v4l2_subdev *sd)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+
+	imx_media_capture_device_unregister(priv->vdev);
+
+	if (priv->fim)
+		imx_media_fim_free(priv->fim);
+
+	if (!IS_ERR_OR_NULL(priv->csi))
+		ipu_csi_put(priv->csi);
+}
+
+static struct media_entity_operations csi_entity_ops = {
+	.link_setup = csi_link_setup,
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static struct v4l2_subdev_core_ops csi_core_ops = {
+	.s_power = csi_s_power,
+	.interrupt_service_routine = csi_eof_isr,
+	.subscribe_event = csi_subscribe_event,
+	.unsubscribe_event = csi_unsubscribe_event,
+};
+
+static struct v4l2_subdev_video_ops csi_video_ops = {
+	.s_stream = csi_s_stream,
+};
+
+static struct v4l2_subdev_pad_ops csi_pad_ops = {
+	.enum_mbus_code = csi_enum_mbus_code,
+	.get_fmt = csi_get_fmt,
+	.set_fmt = csi_set_fmt,
+	.get_selection = csi_get_selection,
+	.set_selection = csi_set_selection,
+	.link_validate = csi_link_validate,
+};
+
+static struct v4l2_subdev_ops csi_subdev_ops = {
+	.core = &csi_core_ops,
+	.video = &csi_video_ops,
+	.pad = &csi_pad_ops,
+};
+
+static struct v4l2_subdev_internal_ops csi_internal_ops = {
+	.registered = csi_registered,
+	.unregistered = csi_unregistered,
+};
+
+static int imx_csi_probe(struct platform_device *pdev)
+{
+	struct ipu_client_platformdata *pdata;
+	struct pinctrl *pinctrl;
+	struct csi_priv *priv;
+	int ret;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, &priv->sd);
+	priv->dev = &pdev->dev;
+
+	ret = dma_set_coherent_mask(priv->dev, DMA_BIT_MASK(32));
+	if (ret)
+		return ret;
+
+	/* get parent IPU */
+	priv->ipu = dev_get_drvdata(priv->dev->parent);
+
+	/* get our CSI id */
+	pdata = priv->dev->platform_data;
+	priv->csi_id = pdata->csi;
+	priv->smfc_id = (priv->csi_id == 0) ? 0 : 2;
+
+	init_timer(&priv->eof_timeout_timer);
+	priv->eof_timeout_timer.data = (unsigned long)priv;
+	priv->eof_timeout_timer.function = csi_idmac_eof_timeout;
+	spin_lock_init(&priv->irqlock);
+
+	v4l2_subdev_init(&priv->sd, &csi_subdev_ops);
+	v4l2_set_subdevdata(&priv->sd, priv);
+	priv->sd.internal_ops = &csi_internal_ops;
+	priv->sd.entity.ops = &csi_entity_ops;
+	priv->sd.entity.function = MEDIA_ENT_F_PROC_VIDEO_PIXEL_FORMATTER;
+	priv->sd.dev = &pdev->dev;
+	priv->sd.of_node = pdata->of_node;
+	priv->sd.owner = THIS_MODULE;
+	priv->sd.flags = V4L2_SUBDEV_FL_HAS_DEVNODE | V4L2_SUBDEV_FL_HAS_EVENTS;
+	priv->sd.grp_id = priv->csi_id ?
+		IMX_MEDIA_GRP_ID_CSI1 : IMX_MEDIA_GRP_ID_CSI0;
+	imx_media_grp_id_to_sd_name(priv->sd.name, sizeof(priv->sd.name),
+				    priv->sd.grp_id, ipu_get_num(priv->ipu));
+
+	priv->vdev = imx_media_capture_device_init(&priv->sd,
+						   CSI_SRC_PAD_IDMAC);
+	if (IS_ERR(priv->vdev))
+		return PTR_ERR(priv->vdev);
+
+	v4l2_ctrl_handler_init(&priv->ctrl_hdlr, 0);
+	priv->sd.ctrl_handler = &priv->ctrl_hdlr;
+
+	/*
+	 * The IPUv3 driver did not assign an of_node to this
+	 * device. As a result, pinctrl does not automatically
+	 * configure our pin groups, so we need to do that manually
+	 * here, after setting this device's of_node.
+	 */
+	priv->dev->of_node = pdata->of_node;
+	pinctrl = devm_pinctrl_get_select_default(priv->dev);
+
+	mutex_init(&priv->lock);
+
+	ret = v4l2_async_register_subdev(&priv->sd);
+	if (ret)
+		goto free;
+
+	return 0;
+free:
+	v4l2_ctrl_handler_free(&priv->ctrl_hdlr);
+	mutex_destroy(&priv->lock);
+	imx_media_capture_device_remove(priv->vdev);
+	return ret;
+}
+
+static int imx_csi_remove(struct platform_device *pdev)
+{
+	struct v4l2_subdev *sd = platform_get_drvdata(pdev);
+	struct csi_priv *priv = sd_to_dev(sd);
+
+	v4l2_ctrl_handler_free(&priv->ctrl_hdlr);
+	mutex_destroy(&priv->lock);
+	imx_media_capture_device_remove(priv->vdev);
+	v4l2_async_unregister_subdev(sd);
+	media_entity_cleanup(&sd->entity);
+
+	return 0;
+}
+
+static const struct platform_device_id imx_csi_ids[] = {
+	{ .name = "imx-ipuv3-csi" },
+	{ },
+};
+MODULE_DEVICE_TABLE(platform, imx_csi_ids);
+
+static struct platform_driver imx_csi_driver = {
+	.probe = imx_csi_probe,
+	.remove = imx_csi_remove,
+	.id_table = imx_csi_ids,
+	.driver = {
+		.name = "imx-ipuv3-csi",
+	},
+};
+module_platform_driver(imx_csi_driver);
+
+MODULE_DESCRIPTION("i.MX CSI subdev driver");
+MODULE_AUTHOR("Steve Longerbeam <steve_longerbeam@mentor.com>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:imx-ipuv3-csi");
-- 
2.7.4

[PATCH v5 26/39] media: imx: Add VDIC subdev driver

[Steve Longerbeam]

This is a media entity subdevice driver for the i.MX Video De-Interlacing
or Combining Block. So far this entity does not implement the Combining
function but only motion compensated deinterlacing. Video frames are
received from the CSI and are routed to the IC PRPVF entity.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/Makefile         |   1 +
 drivers/staging/media/imx/imx-media-vdic.c | 952 +++++++++++++++++++++++++++++
 2 files changed, 953 insertions(+)
 create mode 100644 drivers/staging/media/imx/imx-media-vdic.c

diff --git a/drivers/staging/media/imx/Makefile b/drivers/staging/media/imx/Makefile
index c054490..1f01520 100644
--- a/drivers/staging/media/imx/Makefile
+++ b/drivers/staging/media/imx/Makefile
@@ -4,5 +4,6 @@ imx-media-common-objs := imx-media-utils.o imx-media-fim.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-common.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-capture.o
+obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-vdic.o
 
 obj-$(CONFIG_VIDEO_IMX_CSI) += imx-media-csi.o
diff --git a/drivers/staging/media/imx/imx-media-vdic.c b/drivers/staging/media/imx/imx-media-vdic.c
new file mode 100644
index 0000000..0e7c24c
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media-vdic.c
@@ -0,0 +1,952 @@
+/*
+ * V4L2 Deinterlacer Subdev for Freescale i.MX5/6 SOC
+ *
+ * Copyright (c) 2017 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/timer.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-ioctl.h>
+#include <media/v4l2-mc.h>
+#include <media/v4l2-subdev.h>
+#include <media/imx.h>
+#include "imx-media.h"
+
+/*
+ * This subdev implements two different video pipelines:
+ *
+ * CSI -> VDIC
+ *
+ * In this pipeline, the CSI sends a single interlaced field F(n-1)
+ * directly to the VDIC (and optionally the following field F(n)
+ * can be sent to memory via IDMAC channel 13). This pipeline only works
+ * in VDIC's high motion mode, which only requires a single field for
+ * processing. The other motion modes (low and medium) require three
+ * fields, so this pipeline does not work in those modes. Also, it is
+ * not clear how this pipeline can deal with the various field orders
+ * (sequential BT/TB, interlaced BT/TB).
+ *
+ * MEM -> CH8,9,10 -> VDIC
+ *
+ * In this pipeline, previous field F(n-1), current field F(n), and next
+ * field F(n+1) are transferred to the VDIC via IDMAC channels 8,9,10.
+ * These memory buffers can come from a video output or mem2mem device.
+ * All motion modes are supported by this pipeline.
+ *
+ * The "direct" CSI->VDIC pipeline requires no DMA, but it can only be
+ * used in high motion mode.
+ */
+
+struct vdic_priv;
+
+struct vdic_pipeline_ops {
+	int (*setup)(struct vdic_priv *priv);
+	void (*start)(struct vdic_priv *priv);
+	void (*stop)(struct vdic_priv *priv);
+	void (*disable)(struct vdic_priv *priv);
+};
+
+/*
+ * Min/Max supported width and heights.
+ */
+#define MIN_W       176
+#define MIN_H       144
+#define MAX_W_VDIC  968
+#define MAX_H_VDIC 2048
+#define W_ALIGN    4 /* multiple of 16 pixels */
+#define H_ALIGN    1 /* multiple of 2 lines */
+#define S_ALIGN    1 /* multiple of 2 */
+
+struct vdic_priv {
+	struct device        *dev;
+	struct ipu_soc       *ipu;
+	struct imx_media_dev *md;
+	struct v4l2_subdev   sd;
+	struct media_pad pad[VDIC_NUM_PADS];
+	int ipu_id;
+
+	/* lock to protect all members below */
+	struct mutex lock;
+
+	/* IPU units we require */
+	struct ipu_vdi *vdi;
+
+	int active_input_pad;
+
+	struct ipuv3_channel *vdi_in_ch_p; /* F(n-1) transfer channel */
+	struct ipuv3_channel *vdi_in_ch;   /* F(n) transfer channel */
+	struct ipuv3_channel *vdi_in_ch_n; /* F(n+1) transfer channel */
+
+	/* pipeline operations */
+	struct vdic_pipeline_ops *ops;
+
+	/* current and previous input buffers indirect path */
+	struct imx_media_buffer *curr_in_buf;
+	struct imx_media_buffer *prev_in_buf;
+
+	/*
+	 * translated field type, input line stride, and field size
+	 * for indirect path
+	 */
+	u32 fieldtype;
+	u32 in_stride;
+	u32 field_size;
+
+	/* the source (a video device or subdev) */
+	struct media_entity *src;
+	/* the sink that will receive the progressive out buffers */
+	struct v4l2_subdev *sink_sd;
+
+	struct v4l2_mbus_framefmt format_mbus[VDIC_NUM_PADS];
+	const struct imx_media_pixfmt *cc[VDIC_NUM_PADS];
+	struct v4l2_fract frame_interval;
+
+	/* the video device at IDMAC input pad */
+	struct imx_media_video_dev *vdev;
+
+	bool csi_direct;  /* using direct CSI->VDIC->IC pipeline */
+
+	/* motion select control */
+	struct v4l2_ctrl_handler ctrl_hdlr;
+	enum ipu_motion_sel motion;
+
+	bool stream_on; /* streaming is on */
+};
+
+static void vdic_put_ipu_resources(struct vdic_priv *priv)
+{
+	if (!IS_ERR_OR_NULL(priv->vdi_in_ch_p))
+		ipu_idmac_put(priv->vdi_in_ch_p);
+	priv->vdi_in_ch_p = NULL;
+
+	if (!IS_ERR_OR_NULL(priv->vdi_in_ch))
+		ipu_idmac_put(priv->vdi_in_ch);
+	priv->vdi_in_ch = NULL;
+
+	if (!IS_ERR_OR_NULL(priv->vdi_in_ch_n))
+		ipu_idmac_put(priv->vdi_in_ch_n);
+	priv->vdi_in_ch_n = NULL;
+
+	if (!IS_ERR_OR_NULL(priv->vdi))
+		ipu_vdi_put(priv->vdi);
+	priv->vdi = NULL;
+}
+
+static int vdic_get_ipu_resources(struct vdic_priv *priv)
+{
+	int ret, err_chan;
+
+	priv->ipu = priv->md->ipu[priv->ipu_id];
+
+	priv->vdi = ipu_vdi_get(priv->ipu);
+	if (IS_ERR(priv->vdi)) {
+		v4l2_err(&priv->sd, "failed to get VDIC\n");
+		ret = PTR_ERR(priv->vdi);
+		goto out;
+	}
+
+	if (!priv->csi_direct) {
+		priv->vdi_in_ch_p = ipu_idmac_get(priv->ipu,
+						  IPUV3_CHANNEL_MEM_VDI_PREV);
+		if (IS_ERR(priv->vdi_in_ch_p)) {
+			err_chan = IPUV3_CHANNEL_MEM_VDI_PREV;
+			ret = PTR_ERR(priv->vdi_in_ch_p);
+			goto out_err_chan;
+		}
+
+		priv->vdi_in_ch = ipu_idmac_get(priv->ipu,
+						IPUV3_CHANNEL_MEM_VDI_CUR);
+		if (IS_ERR(priv->vdi_in_ch)) {
+			err_chan = IPUV3_CHANNEL_MEM_VDI_CUR;
+			ret = PTR_ERR(priv->vdi_in_ch);
+			goto out_err_chan;
+		}
+
+		priv->vdi_in_ch_n = ipu_idmac_get(priv->ipu,
+						  IPUV3_CHANNEL_MEM_VDI_NEXT);
+		if (IS_ERR(priv->vdi_in_ch_n)) {
+			err_chan = IPUV3_CHANNEL_MEM_VDI_NEXT;
+			ret = PTR_ERR(priv->vdi_in_ch_n);
+			goto out_err_chan;
+		}
+	}
+
+	return 0;
+
+out_err_chan:
+	v4l2_err(&priv->sd, "could not get IDMAC channel %u\n", err_chan);
+out:
+	vdic_put_ipu_resources(priv);
+	return ret;
+}
+
+/*
+ * This function is currently unused, but will be called when the
+ * output/mem2mem device at the IDMAC input pad sends us a new
+ * buffer. It kicks off the IDMAC read channels to bring in the
+ * buffer fields from memory and begin the conversions.
+ */
+static void __maybe_unused prepare_vdi_in_buffers(struct vdic_priv *priv,
+						  struct imx_media_buffer *curr)
+{
+	dma_addr_t prev_phys, curr_phys, next_phys;
+	struct imx_media_buffer *prev;
+	struct vb2_buffer *curr_vb, *prev_vb;
+	u32 fs = priv->field_size;
+	u32 is = priv->in_stride;
+
+	/* current input buffer is now previous */
+	priv->prev_in_buf = priv->curr_in_buf;
+	priv->curr_in_buf = curr;
+	prev = priv->prev_in_buf ? priv->prev_in_buf : curr;
+
+	prev_vb = &prev->vbuf.vb2_buf;
+	curr_vb = &curr->vbuf.vb2_buf;
+
+	switch (priv->fieldtype) {
+	case V4L2_FIELD_SEQ_TB:
+		prev_phys = vb2_dma_contig_plane_dma_addr(prev_vb, 0);
+		curr_phys = vb2_dma_contig_plane_dma_addr(curr_vb, 0) + fs;
+		next_phys = vb2_dma_contig_plane_dma_addr(curr_vb, 0);
+		break;
+	case V4L2_FIELD_SEQ_BT:
+		prev_phys = vb2_dma_contig_plane_dma_addr(prev_vb, 0) + fs;
+		curr_phys = vb2_dma_contig_plane_dma_addr(curr_vb, 0);
+		next_phys = vb2_dma_contig_plane_dma_addr(curr_vb, 0) + fs;
+		break;
+	case V4L2_FIELD_INTERLACED_BT:
+		prev_phys = vb2_dma_contig_plane_dma_addr(prev_vb, 0) + is;
+		curr_phys = vb2_dma_contig_plane_dma_addr(curr_vb, 0);
+		next_phys = vb2_dma_contig_plane_dma_addr(curr_vb, 0) + is;
+		break;
+	default:
+		/* assume V4L2_FIELD_INTERLACED_TB */
+		prev_phys = vb2_dma_contig_plane_dma_addr(prev_vb, 0);
+		curr_phys = vb2_dma_contig_plane_dma_addr(curr_vb, 0) + is;
+		next_phys = vb2_dma_contig_plane_dma_addr(curr_vb, 0);
+		break;
+	}
+
+	ipu_cpmem_set_buffer(priv->vdi_in_ch_p, 0, prev_phys);
+	ipu_cpmem_set_buffer(priv->vdi_in_ch,   0, curr_phys);
+	ipu_cpmem_set_buffer(priv->vdi_in_ch_n, 0, next_phys);
+
+	ipu_idmac_select_buffer(priv->vdi_in_ch_p, 0);
+	ipu_idmac_select_buffer(priv->vdi_in_ch, 0);
+	ipu_idmac_select_buffer(priv->vdi_in_ch_n, 0);
+}
+
+static int setup_vdi_channel(struct vdic_priv *priv,
+			     struct ipuv3_channel *channel,
+			     dma_addr_t phys0, dma_addr_t phys1)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	unsigned int burst_size;
+	struct ipu_image image;
+	int ret;
+
+	ipu_cpmem_zero(channel);
+
+	memset(&image, 0, sizeof(image));
+	image.pix = vdev->fmt.fmt.pix;
+	/* one field to VDIC channels */
+	image.pix.height /= 2;
+	image.rect.width = image.pix.width;
+	image.rect.height = image.pix.height;
+	image.phys0 = phys0;
+	image.phys1 = phys1;
+
+	ret = ipu_cpmem_set_image(channel, &image);
+	if (ret)
+		return ret;
+
+	burst_size = (image.pix.width & 0xf) ? 8 : 16;
+	ipu_cpmem_set_burstsize(channel, burst_size);
+
+	ipu_cpmem_set_axi_id(channel, 1);
+
+	ipu_idmac_set_double_buffer(channel, false);
+
+	return 0;
+}
+
+static int vdic_setup_direct(struct vdic_priv *priv)
+{
+	/* set VDIC to receive from CSI for direct path */
+	ipu_fsu_link(priv->ipu, IPUV3_CHANNEL_CSI_DIRECT,
+		     IPUV3_CHANNEL_CSI_VDI_PREV);
+
+	return 0;
+}
+
+static void vdic_start_direct(struct vdic_priv *priv)
+{
+}
+
+static void vdic_stop_direct(struct vdic_priv *priv)
+{
+}
+
+static void vdic_disable_direct(struct vdic_priv *priv)
+{
+	ipu_fsu_unlink(priv->ipu, IPUV3_CHANNEL_CSI_DIRECT,
+		       IPUV3_CHANNEL_CSI_VDI_PREV);
+}
+
+static int vdic_setup_indirect(struct vdic_priv *priv)
+{
+	struct v4l2_mbus_framefmt *infmt;
+	const struct imx_media_pixfmt *incc;
+	int in_size, ret;
+
+	infmt = &priv->format_mbus[VDIC_SINK_PAD_IDMAC];
+	incc = priv->cc[VDIC_SINK_PAD_IDMAC];
+
+	in_size = (infmt->width * incc->bpp * infmt->height) >> 3;
+
+	/* 1/2 full image size */
+	priv->field_size = in_size / 2;
+	priv->in_stride = incc->planar ?
+		infmt->width : (infmt->width * incc->bpp) >> 3;
+
+	priv->prev_in_buf = NULL;
+	priv->curr_in_buf = NULL;
+
+	priv->fieldtype = infmt->field;
+
+	/* init the vdi-in channels */
+	ret = setup_vdi_channel(priv, priv->vdi_in_ch_p, 0, 0);
+	if (ret)
+		return ret;
+	ret = setup_vdi_channel(priv, priv->vdi_in_ch, 0, 0);
+	if (ret)
+		return ret;
+	return setup_vdi_channel(priv, priv->vdi_in_ch_n, 0, 0);
+}
+
+static void vdic_start_indirect(struct vdic_priv *priv)
+{
+	/* enable the channels */
+	ipu_idmac_enable_channel(priv->vdi_in_ch_p);
+	ipu_idmac_enable_channel(priv->vdi_in_ch);
+	ipu_idmac_enable_channel(priv->vdi_in_ch_n);
+}
+
+static void vdic_stop_indirect(struct vdic_priv *priv)
+{
+	/* disable channels */
+	ipu_idmac_disable_channel(priv->vdi_in_ch_p);
+	ipu_idmac_disable_channel(priv->vdi_in_ch);
+	ipu_idmac_disable_channel(priv->vdi_in_ch_n);
+}
+
+static void vdic_disable_indirect(struct vdic_priv *priv)
+{
+}
+
+static struct vdic_pipeline_ops direct_ops = {
+	.setup = vdic_setup_direct,
+	.start = vdic_start_direct,
+	.stop = vdic_stop_direct,
+	.disable = vdic_disable_direct,
+};
+
+static struct vdic_pipeline_ops indirect_ops = {
+	.setup = vdic_setup_indirect,
+	.start = vdic_start_indirect,
+	.stop = vdic_stop_indirect,
+	.disable = vdic_disable_indirect,
+};
+
+static int vdic_start(struct vdic_priv *priv)
+{
+	struct v4l2_mbus_framefmt *infmt;
+	int ret;
+
+	infmt = &priv->format_mbus[priv->active_input_pad];
+
+	priv->ops = priv->csi_direct ? &direct_ops : &indirect_ops;
+
+	ret = vdic_get_ipu_resources(priv);
+	if (ret)
+		return ret;
+
+	/*
+	 * init the VDIC.
+	 *
+	 * note we don't give infmt->code to ipu_vdi_setup(). The VDIC
+	 * only supports 4:2:2 or 4:2:0, and this subdev will only
+	 * negotiate 4:2:2 at its sink pads.
+	 */
+	ipu_vdi_setup(priv->vdi, MEDIA_BUS_FMT_UYVY8_2X8,
+		      infmt->width, infmt->height);
+	ipu_vdi_set_field_order(priv->vdi, V4L2_STD_UNKNOWN, infmt->field);
+	ipu_vdi_set_motion(priv->vdi, priv->motion);
+
+	ret = priv->ops->setup(priv);
+	if (ret)
+		goto out_put_ipu;
+
+	ipu_vdi_enable(priv->vdi);
+
+	priv->ops->start(priv);
+
+	return 0;
+
+out_put_ipu:
+	vdic_put_ipu_resources(priv);
+	return ret;
+}
+
+static void vdic_stop(struct vdic_priv *priv)
+{
+	priv->ops->stop(priv);
+	ipu_vdi_disable(priv->vdi);
+	priv->ops->disable(priv);
+
+	vdic_put_ipu_resources(priv);
+}
+
+/*
+ * V4L2 subdev operations.
+ */
+
+static int vdic_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct vdic_priv *priv = container_of(ctrl->handler,
+					      struct vdic_priv, ctrl_hdlr);
+	enum ipu_motion_sel motion;
+	int ret = 0;
+
+	mutex_lock(&priv->lock);
+
+	switch (ctrl->id) {
+	case V4L2_CID_DEINTERLACING_MODE:
+		motion = ctrl->val;
+		if (motion != priv->motion) {
+			/* can't change motion control mid-streaming */
+			if (priv->stream_on) {
+				ret = -EBUSY;
+				goto out;
+			}
+			priv->motion = motion;
+		}
+		break;
+	default:
+		v4l2_err(&priv->sd, "Invalid control\n");
+		ret = -EINVAL;
+	}
+
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static const struct v4l2_ctrl_ops vdic_ctrl_ops = {
+	.s_ctrl = vdic_s_ctrl,
+};
+
+static const char * const vdic_ctrl_motion_menu[] = {
+	"No Motion Compensation",
+	"Low Motion",
+	"Medium Motion",
+	"High Motion",
+};
+
+static int vdic_init_controls(struct vdic_priv *priv)
+{
+	struct v4l2_ctrl_handler *hdlr = &priv->ctrl_hdlr;
+	int ret;
+
+	v4l2_ctrl_handler_init(hdlr, 1);
+
+	v4l2_ctrl_new_std_menu_items(hdlr, &vdic_ctrl_ops,
+				     V4L2_CID_DEINTERLACING_MODE,
+				     HIGH_MOTION, 0, HIGH_MOTION,
+				     vdic_ctrl_motion_menu);
+
+	priv->sd.ctrl_handler = hdlr;
+
+	if (hdlr->error) {
+		ret = hdlr->error;
+		goto out_free;
+	}
+
+	v4l2_ctrl_handler_setup(hdlr);
+	return 0;
+
+out_free:
+	v4l2_ctrl_handler_free(hdlr);
+	return ret;
+}
+
+static int vdic_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
+	int ret = 0;
+
+	mutex_lock(&priv->lock);
+
+	if (!priv->src || !priv->sink_sd) {
+		ret = -EPIPE;
+		goto out;
+	}
+
+	dev_dbg(priv->dev, "stream %s\n", enable ? "ON" : "OFF");
+
+	if (enable && !priv->stream_on)
+		ret = vdic_start(priv);
+	else if (!enable && priv->stream_on)
+		vdic_stop(priv);
+
+	if (!ret)
+		priv->stream_on = enable;
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int vdic_enum_mbus_code(struct v4l2_subdev *sd,
+			       struct v4l2_subdev_pad_config *cfg,
+			       struct v4l2_subdev_mbus_code_enum *code)
+{
+	if (code->pad >= VDIC_NUM_PADS)
+		return -EINVAL;
+
+	if (code->pad == VDIC_SINK_PAD_IDMAC)
+		return imx_media_enum_format(NULL, &code->code, code->index,
+					     false, false);
+
+	return imx_media_enum_ipu_format(NULL, &code->code, code->index, false);
+}
+
+static struct v4l2_mbus_framefmt *
+__vdic_get_fmt(struct vdic_priv *priv, struct v4l2_subdev_pad_config *cfg,
+	       unsigned int pad, enum v4l2_subdev_format_whence which)
+{
+	if (which == V4L2_SUBDEV_FORMAT_TRY)
+		return v4l2_subdev_get_try_format(&priv->sd, cfg, pad);
+	else
+		return &priv->format_mbus[pad];
+}
+
+static int vdic_get_fmt(struct v4l2_subdev *sd,
+			struct v4l2_subdev_pad_config *cfg,
+			struct v4l2_subdev_format *sdformat)
+{
+	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_mbus_framefmt *fmt;
+	int ret = 0;
+
+	if (sdformat->pad >= VDIC_NUM_PADS)
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	fmt = __vdic_get_fmt(priv, cfg, sdformat->pad, sdformat->which);
+	if (!fmt) {
+		ret = -EINVAL;
+		goto out;
+	}
+
+	sdformat->format = *fmt;
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int vdic_set_fmt(struct v4l2_subdev *sd,
+			struct v4l2_subdev_pad_config *cfg,
+			struct v4l2_subdev_format *sdformat)
+{
+	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
+	const struct imx_media_pixfmt *cc;
+	struct v4l2_mbus_framefmt *infmt;
+	int ret = 0;
+	u32 code;
+
+	if (sdformat->pad >= VDIC_NUM_PADS)
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	if (priv->stream_on) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W_VDIC,
+			      W_ALIGN, &sdformat->format.height,
+			      MIN_H, MAX_H_VDIC, H_ALIGN, S_ALIGN);
+
+	switch (sdformat->pad) {
+	case VDIC_SRC_PAD_DIRECT:
+		infmt = __vdic_get_fmt(priv, cfg, priv->active_input_pad,
+				       sdformat->which);
+
+		cc = imx_media_find_ipu_format(0, sdformat->format.code, false);
+		if (!cc) {
+			imx_media_enum_ipu_format(NULL, &code, 0, false);
+			cc = imx_media_find_ipu_format(0, code, false);
+			sdformat->format.code = cc->codes[0];
+		}
+
+		sdformat->format.width = infmt->width;
+		sdformat->format.height = infmt->height;
+		/* output is always progressive! */
+		sdformat->format.field = V4L2_FIELD_NONE;
+		break;
+	case VDIC_SINK_PAD_IDMAC:
+	case VDIC_SINK_PAD_DIRECT:
+		if (sdformat->pad == VDIC_SINK_PAD_DIRECT) {
+			cc = imx_media_find_ipu_format(0, sdformat->format.code,
+						       false);
+			if (!cc) {
+				imx_media_enum_ipu_format(NULL, &code, 0,
+							  false);
+				cc = imx_media_find_ipu_format(0, code, false);
+				sdformat->format.code = cc->codes[0];
+			}
+		} else {
+			cc = imx_media_find_format(0, sdformat->format.code,
+						   false, false);
+			if (!cc) {
+				imx_media_enum_format(NULL, &code, 0,
+						      false, false);
+				cc = imx_media_find_format(0, code,
+							   false, false);
+				sdformat->format.code = cc->codes[0];
+			}
+		}
+
+		/* input must be interlaced! Choose SEQ_TB if not */
+		if (!V4L2_FIELD_HAS_BOTH(sdformat->format.field))
+			sdformat->format.field = V4L2_FIELD_SEQ_TB;
+		break;
+	default:
+		ret = -EINVAL;
+		goto out;
+	}
+
+	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
+		cfg->try_fmt = sdformat->format;
+	} else {
+		priv->format_mbus[sdformat->pad] = sdformat->format;
+		priv->cc[sdformat->pad] = cc;
+	}
+
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int vdic_g_frame_interval(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_frame_interval *fi)
+{
+	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
+
+	mutex_lock(&priv->lock);
+	fi->interval = priv->frame_interval;
+	mutex_unlock(&priv->lock);
+
+	return 0;
+}
+
+static int vdic_s_frame_interval(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_frame_interval *fi)
+{
+	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
+
+	mutex_lock(&priv->lock);
+
+	/* Output pads mirror active input pad, no limits on input pads */
+	if (fi->pad == VDIC_SRC_PAD_DIRECT)
+		fi->interval = priv->frame_interval;
+
+	priv->frame_interval = fi->interval;
+
+	mutex_unlock(&priv->lock);
+
+	return 0;
+}
+
+static int vdic_link_setup(struct media_entity *entity,
+			    const struct media_pad *local,
+			    const struct media_pad *remote, u32 flags)
+{
+	struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity);
+	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_subdev *remote_sd;
+	int ret = 0;
+
+	dev_dbg(priv->dev, "link setup %s -> %s", remote->entity->name,
+		local->entity->name);
+
+	mutex_lock(&priv->lock);
+
+	if (local->flags & MEDIA_PAD_FL_SOURCE) {
+		if (!is_media_entity_v4l2_subdev(remote->entity)) {
+			ret = -EINVAL;
+			goto out;
+		}
+
+		remote_sd = media_entity_to_v4l2_subdev(remote->entity);
+
+		if (flags & MEDIA_LNK_FL_ENABLED) {
+			if (priv->sink_sd) {
+				ret = -EBUSY;
+				goto out;
+			}
+			priv->sink_sd = remote_sd;
+		} else {
+			priv->sink_sd = NULL;
+		}
+
+		goto out;
+	}
+
+	/* this is a sink pad */
+
+	if (flags & MEDIA_LNK_FL_ENABLED) {
+		if (priv->src) {
+			ret = -EBUSY;
+			goto out;
+		}
+	} else {
+		priv->src = NULL;
+		goto out;
+	}
+
+	if (local->index == VDIC_SINK_PAD_IDMAC) {
+		struct imx_media_video_dev *vdev = priv->vdev;
+
+		if (!is_media_entity_v4l2_video_device(remote->entity)) {
+			ret = -EINVAL;
+			goto out;
+		}
+		if (!vdev) {
+			ret = -ENODEV;
+			goto out;
+		}
+
+		priv->csi_direct = false;
+	} else {
+		if (!is_media_entity_v4l2_subdev(remote->entity)) {
+			ret = -EINVAL;
+			goto out;
+		}
+
+		remote_sd = media_entity_to_v4l2_subdev(remote->entity);
+
+		/* direct pad must connect to a CSI */
+		if (!(remote_sd->grp_id & IMX_MEDIA_GRP_ID_CSI) ||
+		    remote->index != CSI_SRC_PAD_DIRECT) {
+			ret = -EINVAL;
+			goto out;
+		}
+
+		priv->csi_direct = true;
+	}
+
+	priv->src = remote->entity;
+	/* record which input pad is now active */
+	priv->active_input_pad = local->index;
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int vdic_link_validate(struct v4l2_subdev *sd,
+			      struct media_link *link,
+			      struct v4l2_subdev_format *source_fmt,
+			      struct v4l2_subdev_format *sink_fmt)
+{
+	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
+	int ret;
+
+	ret = v4l2_subdev_link_validate_default(sd, link,
+						source_fmt, sink_fmt);
+	if (ret)
+		return ret;
+
+	ret = v4l2_subdev_link_validate_frame_interval(link);
+	if (ret)
+		return ret;
+
+	mutex_lock(&priv->lock);
+
+	if (priv->csi_direct && priv->motion != HIGH_MOTION) {
+		v4l2_err(&priv->sd,
+			 "direct CSI pipeline requires high motion\n");
+		ret = -EINVAL;
+	}
+
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+/*
+ * retrieve our pads parsed from the OF graph by the media device
+ */
+static int vdic_registered(struct v4l2_subdev *sd)
+{
+	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
+	int i, ret;
+	u32 code;
+
+	/* get media device */
+	priv->md = dev_get_drvdata(sd->v4l2_dev->dev);
+
+	for (i = 0; i < VDIC_NUM_PADS; i++) {
+		priv->pad[i].flags = (i == VDIC_SRC_PAD_DIRECT) ?
+			MEDIA_PAD_FL_SOURCE : MEDIA_PAD_FL_SINK;
+
+		code = 0;
+		if (i != VDIC_SINK_PAD_IDMAC)
+			imx_media_enum_ipu_format(NULL, &code, 0, true);
+
+		/* set a default mbus format  */
+		ret = imx_media_init_mbus_fmt(&priv->format_mbus[i],
+					      640, 480, code, V4L2_FIELD_NONE,
+					      &priv->cc[i]);
+		if (ret)
+			return ret;
+	}
+
+	/* init default frame interval */
+	priv->frame_interval.numerator = 1;
+	priv->frame_interval.denominator = 30;
+
+	priv->active_input_pad = VDIC_SINK_PAD_DIRECT;
+
+	ret = vdic_init_controls(priv);
+	if (ret)
+		return ret;
+
+	ret = media_entity_pads_init(&sd->entity, VDIC_NUM_PADS, priv->pad);
+	if (ret)
+		v4l2_ctrl_handler_free(&priv->ctrl_hdlr);
+
+	return ret;
+}
+
+static void vdic_unregistered(struct v4l2_subdev *sd)
+{
+	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
+
+	v4l2_ctrl_handler_free(&priv->ctrl_hdlr);
+}
+
+static struct v4l2_subdev_pad_ops vdic_pad_ops = {
+	.enum_mbus_code = vdic_enum_mbus_code,
+	.get_fmt = vdic_get_fmt,
+	.set_fmt = vdic_set_fmt,
+	.link_validate = vdic_link_validate,
+};
+
+static struct v4l2_subdev_video_ops vdic_video_ops = {
+	.s_stream = vdic_s_stream,
+	.g_frame_interval = vdic_g_frame_interval,
+	.s_frame_interval = vdic_s_frame_interval,
+};
+
+static struct media_entity_operations vdic_entity_ops = {
+	.link_setup = vdic_link_setup,
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static struct v4l2_subdev_ops vdic_subdev_ops = {
+	.video = &vdic_video_ops,
+	.pad = &vdic_pad_ops,
+};
+
+static struct v4l2_subdev_internal_ops vdic_internal_ops = {
+	.registered = vdic_registered,
+	.unregistered = vdic_unregistered,
+};
+
+static int imx_vdic_probe(struct platform_device *pdev)
+{
+	struct imx_media_internal_sd_platformdata *pdata;
+	struct vdic_priv *priv;
+	int ret;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, &priv->sd);
+	priv->dev = &pdev->dev;
+
+	pdata = priv->dev->platform_data;
+	priv->ipu_id = pdata->ipu_id;
+
+	v4l2_subdev_init(&priv->sd, &vdic_subdev_ops);
+	v4l2_set_subdevdata(&priv->sd, priv);
+	priv->sd.internal_ops = &vdic_internal_ops;
+	priv->sd.entity.ops = &vdic_entity_ops;
+	priv->sd.entity.function = MEDIA_ENT_F_PROC_VIDEO_PIXEL_FORMATTER;
+	priv->sd.dev = &pdev->dev;
+	priv->sd.owner = THIS_MODULE;
+	priv->sd.flags = V4L2_SUBDEV_FL_HAS_DEVNODE;
+	/* get our group id */
+	priv->sd.grp_id = pdata->grp_id;
+	strncpy(priv->sd.name, pdata->sd_name, sizeof(priv->sd.name));
+
+	mutex_init(&priv->lock);
+
+	ret = v4l2_async_register_subdev(&priv->sd);
+	if (ret)
+		goto free;
+
+	return 0;
+free:
+	mutex_destroy(&priv->lock);
+	return ret;
+}
+
+static int imx_vdic_remove(struct platform_device *pdev)
+{
+	struct v4l2_subdev *sd = platform_get_drvdata(pdev);
+	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
+
+	v4l2_info(sd, "Removing\n");
+
+	v4l2_async_unregister_subdev(sd);
+	mutex_destroy(&priv->lock);
+	media_entity_cleanup(&sd->entity);
+
+	return 0;
+}
+
+static const struct platform_device_id imx_vdic_ids[] = {
+	{ .name = "imx-ipuv3-vdic" },
+	{ },
+};
+MODULE_DEVICE_TABLE(platform, imx_vdic_ids);
+
+static struct platform_driver imx_vdic_driver = {
+	.probe = imx_vdic_probe,
+	.remove = imx_vdic_remove,
+	.id_table = imx_vdic_ids,
+	.driver = {
+		.name = "imx-ipuv3-vdic",
+	},
+};
+module_platform_driver(imx_vdic_driver);
+
+MODULE_DESCRIPTION("i.MX VDIC subdev driver");
+MODULE_AUTHOR("Steve Longerbeam <steve_longerbeam@mentor.com>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:imx-ipuv3-vdic");
-- 
2.7.4

[PATCH v5 26/39] media: imx: Add VDIC subdev driver

[Steve Longerbeam]

This is a media entity subdevice driver for the i.MX Video De-Interlacing
or Combining Block. So far this entity does not implement the Combining
function but only motion compensated deinterlacing. Video frames are
received from the CSI and are routed to the IC PRPVF entity.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/Makefile         |   1 +
 drivers/staging/media/imx/imx-media-vdic.c | 952 +++++++++++++++++++++++++++++
 2 files changed, 953 insertions(+)
 create mode 100644 drivers/staging/media/imx/imx-media-vdic.c

diff --git a/drivers/staging/media/imx/Makefile b/drivers/staging/media/imx/Makefile
index c054490..1f01520 100644
--- a/drivers/staging/media/imx/Makefile
+++ b/drivers/staging/media/imx/Makefile
@@ -4,5 +4,6 @@ imx-media-common-objs := imx-media-utils.o imx-media-fim.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-common.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-capture.o
+obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-vdic.o
 
 obj-$(CONFIG_VIDEO_IMX_CSI) += imx-media-csi.o
diff --git a/drivers/staging/media/imx/imx-media-vdic.c b/drivers/staging/media/imx/imx-media-vdic.c
new file mode 100644
index 0000000..0e7c24c
--- /dev/null
+++ b/drivers/staging/media/imx/imx-media-vdic.c
@@ -0,0 +1,952 @@
+/*
+ * V4L2 Deinterlacer Subdev for Freescale i.MX5/6 SOC
+ *
+ * Copyright (c) 2017 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/timer.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-ioctl.h>
+#include <media/v4l2-mc.h>
+#include <media/v4l2-subdev.h>
+#include <media/imx.h>
+#include "imx-media.h"
+
+/*
+ * This subdev implements two different video pipelines:
+ *
+ * CSI -> VDIC
+ *
+ * In this pipeline, the CSI sends a single interlaced field F(n-1)
+ * directly to the VDIC (and optionally the following field F(n)
+ * can be sent to memory via IDMAC channel 13). This pipeline only works
+ * in VDIC's high motion mode, which only requires a single field for
+ * processing. The other motion modes (low and medium) require three
+ * fields, so this pipeline does not work in those modes. Also, it is
+ * not clear how this pipeline can deal with the various field orders
+ * (sequential BT/TB, interlaced BT/TB).
+ *
+ * MEM -> CH8,9,10 -> VDIC
+ *
+ * In this pipeline, previous field F(n-1), current field F(n), and next
+ * field F(n+1) are transferred to the VDIC via IDMAC channels 8,9,10.
+ * These memory buffers can come from a video output or mem2mem device.
+ * All motion modes are supported by this pipeline.
+ *
+ * The "direct" CSI->VDIC pipeline requires no DMA, but it can only be
+ * used in high motion mode.
+ */
+
+struct vdic_priv;
+
+struct vdic_pipeline_ops {
+	int (*setup)(struct vdic_priv *priv);
+	void (*start)(struct vdic_priv *priv);
+	void (*stop)(struct vdic_priv *priv);
+	void (*disable)(struct vdic_priv *priv);
+};
+
+/*
+ * Min/Max supported width and heights.
+ */
+#define MIN_W       176
+#define MIN_H       144
+#define MAX_W_VDIC  968
+#define MAX_H_VDIC 2048
+#define W_ALIGN    4 /* multiple of 16 pixels */
+#define H_ALIGN    1 /* multiple of 2 lines */
+#define S_ALIGN    1 /* multiple of 2 */
+
+struct vdic_priv {
+	struct device        *dev;
+	struct ipu_soc       *ipu;
+	struct imx_media_dev *md;
+	struct v4l2_subdev   sd;
+	struct media_pad pad[VDIC_NUM_PADS];
+	int ipu_id;
+
+	/* lock to protect all members below */
+	struct mutex lock;
+
+	/* IPU units we require */
+	struct ipu_vdi *vdi;
+
+	int active_input_pad;
+
+	struct ipuv3_channel *vdi_in_ch_p; /* F(n-1) transfer channel */
+	struct ipuv3_channel *vdi_in_ch;   /* F(n) transfer channel */
+	struct ipuv3_channel *vdi_in_ch_n; /* F(n+1) transfer channel */
+
+	/* pipeline operations */
+	struct vdic_pipeline_ops *ops;
+
+	/* current and previous input buffers indirect path */
+	struct imx_media_buffer *curr_in_buf;
+	struct imx_media_buffer *prev_in_buf;
+
+	/*
+	 * translated field type, input line stride, and field size
+	 * for indirect path
+	 */
+	u32 fieldtype;
+	u32 in_stride;
+	u32 field_size;
+
+	/* the source (a video device or subdev) */
+	struct media_entity *src;
+	/* the sink that will receive the progressive out buffers */
+	struct v4l2_subdev *sink_sd;
+
+	struct v4l2_mbus_framefmt format_mbus[VDIC_NUM_PADS];
+	const struct imx_media_pixfmt *cc[VDIC_NUM_PADS];
+	struct v4l2_fract frame_interval;
+
+	/* the video device at IDMAC input pad */
+	struct imx_media_video_dev *vdev;
+
+	bool csi_direct;  /* using direct CSI->VDIC->IC pipeline */
+
+	/* motion select control */
+	struct v4l2_ctrl_handler ctrl_hdlr;
+	enum ipu_motion_sel motion;
+
+	bool stream_on; /* streaming is on */
+};
+
+static void vdic_put_ipu_resources(struct vdic_priv *priv)
+{
+	if (!IS_ERR_OR_NULL(priv->vdi_in_ch_p))
+		ipu_idmac_put(priv->vdi_in_ch_p);
+	priv->vdi_in_ch_p = NULL;
+
+	if (!IS_ERR_OR_NULL(priv->vdi_in_ch))
+		ipu_idmac_put(priv->vdi_in_ch);
+	priv->vdi_in_ch = NULL;
+
+	if (!IS_ERR_OR_NULL(priv->vdi_in_ch_n))
+		ipu_idmac_put(priv->vdi_in_ch_n);
+	priv->vdi_in_ch_n = NULL;
+
+	if (!IS_ERR_OR_NULL(priv->vdi))
+		ipu_vdi_put(priv->vdi);
+	priv->vdi = NULL;
+}
+
+static int vdic_get_ipu_resources(struct vdic_priv *priv)
+{
+	int ret, err_chan;
+
+	priv->ipu = priv->md->ipu[priv->ipu_id];
+
+	priv->vdi = ipu_vdi_get(priv->ipu);
+	if (IS_ERR(priv->vdi)) {
+		v4l2_err(&priv->sd, "failed to get VDIC\n");
+		ret = PTR_ERR(priv->vdi);
+		goto out;
+	}
+
+	if (!priv->csi_direct) {
+		priv->vdi_in_ch_p = ipu_idmac_get(priv->ipu,
+						  IPUV3_CHANNEL_MEM_VDI_PREV);
+		if (IS_ERR(priv->vdi_in_ch_p)) {
+			err_chan = IPUV3_CHANNEL_MEM_VDI_PREV;
+			ret = PTR_ERR(priv->vdi_in_ch_p);
+			goto out_err_chan;
+		}
+
+		priv->vdi_in_ch = ipu_idmac_get(priv->ipu,
+						IPUV3_CHANNEL_MEM_VDI_CUR);
+		if (IS_ERR(priv->vdi_in_ch)) {
+			err_chan = IPUV3_CHANNEL_MEM_VDI_CUR;
+			ret = PTR_ERR(priv->vdi_in_ch);
+			goto out_err_chan;
+		}
+
+		priv->vdi_in_ch_n = ipu_idmac_get(priv->ipu,
+						  IPUV3_CHANNEL_MEM_VDI_NEXT);
+		if (IS_ERR(priv->vdi_in_ch_n)) {
+			err_chan = IPUV3_CHANNEL_MEM_VDI_NEXT;
+			ret = PTR_ERR(priv->vdi_in_ch_n);
+			goto out_err_chan;
+		}
+	}
+
+	return 0;
+
+out_err_chan:
+	v4l2_err(&priv->sd, "could not get IDMAC channel %u\n", err_chan);
+out:
+	vdic_put_ipu_resources(priv);
+	return ret;
+}
+
+/*
+ * This function is currently unused, but will be called when the
+ * output/mem2mem device at the IDMAC input pad sends us a new
+ * buffer. It kicks off the IDMAC read channels to bring in the
+ * buffer fields from memory and begin the conversions.
+ */
+static void __maybe_unused prepare_vdi_in_buffers(struct vdic_priv *priv,
+						  struct imx_media_buffer *curr)
+{
+	dma_addr_t prev_phys, curr_phys, next_phys;
+	struct imx_media_buffer *prev;
+	struct vb2_buffer *curr_vb, *prev_vb;
+	u32 fs = priv->field_size;
+	u32 is = priv->in_stride;
+
+	/* current input buffer is now previous */
+	priv->prev_in_buf = priv->curr_in_buf;
+	priv->curr_in_buf = curr;
+	prev = priv->prev_in_buf ? priv->prev_in_buf : curr;
+
+	prev_vb = &prev->vbuf.vb2_buf;
+	curr_vb = &curr->vbuf.vb2_buf;
+
+	switch (priv->fieldtype) {
+	case V4L2_FIELD_SEQ_TB:
+		prev_phys = vb2_dma_contig_plane_dma_addr(prev_vb, 0);
+		curr_phys = vb2_dma_contig_plane_dma_addr(curr_vb, 0) + fs;
+		next_phys = vb2_dma_contig_plane_dma_addr(curr_vb, 0);
+		break;
+	case V4L2_FIELD_SEQ_BT:
+		prev_phys = vb2_dma_contig_plane_dma_addr(prev_vb, 0) + fs;
+		curr_phys = vb2_dma_contig_plane_dma_addr(curr_vb, 0);
+		next_phys = vb2_dma_contig_plane_dma_addr(curr_vb, 0) + fs;
+		break;
+	case V4L2_FIELD_INTERLACED_BT:
+		prev_phys = vb2_dma_contig_plane_dma_addr(prev_vb, 0) + is;
+		curr_phys = vb2_dma_contig_plane_dma_addr(curr_vb, 0);
+		next_phys = vb2_dma_contig_plane_dma_addr(curr_vb, 0) + is;
+		break;
+	default:
+		/* assume V4L2_FIELD_INTERLACED_TB */
+		prev_phys = vb2_dma_contig_plane_dma_addr(prev_vb, 0);
+		curr_phys = vb2_dma_contig_plane_dma_addr(curr_vb, 0) + is;
+		next_phys = vb2_dma_contig_plane_dma_addr(curr_vb, 0);
+		break;
+	}
+
+	ipu_cpmem_set_buffer(priv->vdi_in_ch_p, 0, prev_phys);
+	ipu_cpmem_set_buffer(priv->vdi_in_ch,   0, curr_phys);
+	ipu_cpmem_set_buffer(priv->vdi_in_ch_n, 0, next_phys);
+
+	ipu_idmac_select_buffer(priv->vdi_in_ch_p, 0);
+	ipu_idmac_select_buffer(priv->vdi_in_ch, 0);
+	ipu_idmac_select_buffer(priv->vdi_in_ch_n, 0);
+}
+
+static int setup_vdi_channel(struct vdic_priv *priv,
+			     struct ipuv3_channel *channel,
+			     dma_addr_t phys0, dma_addr_t phys1)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	unsigned int burst_size;
+	struct ipu_image image;
+	int ret;
+
+	ipu_cpmem_zero(channel);
+
+	memset(&image, 0, sizeof(image));
+	image.pix = vdev->fmt.fmt.pix;
+	/* one field to VDIC channels */
+	image.pix.height /= 2;
+	image.rect.width = image.pix.width;
+	image.rect.height = image.pix.height;
+	image.phys0 = phys0;
+	image.phys1 = phys1;
+
+	ret = ipu_cpmem_set_image(channel, &image);
+	if (ret)
+		return ret;
+
+	burst_size = (image.pix.width & 0xf) ? 8 : 16;
+	ipu_cpmem_set_burstsize(channel, burst_size);
+
+	ipu_cpmem_set_axi_id(channel, 1);
+
+	ipu_idmac_set_double_buffer(channel, false);
+
+	return 0;
+}
+
+static int vdic_setup_direct(struct vdic_priv *priv)
+{
+	/* set VDIC to receive from CSI for direct path */
+	ipu_fsu_link(priv->ipu, IPUV3_CHANNEL_CSI_DIRECT,
+		     IPUV3_CHANNEL_CSI_VDI_PREV);
+
+	return 0;
+}
+
+static void vdic_start_direct(struct vdic_priv *priv)
+{
+}
+
+static void vdic_stop_direct(struct vdic_priv *priv)
+{
+}
+
+static void vdic_disable_direct(struct vdic_priv *priv)
+{
+	ipu_fsu_unlink(priv->ipu, IPUV3_CHANNEL_CSI_DIRECT,
+		       IPUV3_CHANNEL_CSI_VDI_PREV);
+}
+
+static int vdic_setup_indirect(struct vdic_priv *priv)
+{
+	struct v4l2_mbus_framefmt *infmt;
+	const struct imx_media_pixfmt *incc;
+	int in_size, ret;
+
+	infmt = &priv->format_mbus[VDIC_SINK_PAD_IDMAC];
+	incc = priv->cc[VDIC_SINK_PAD_IDMAC];
+
+	in_size = (infmt->width * incc->bpp * infmt->height) >> 3;
+
+	/* 1/2 full image size */
+	priv->field_size = in_size / 2;
+	priv->in_stride = incc->planar ?
+		infmt->width : (infmt->width * incc->bpp) >> 3;
+
+	priv->prev_in_buf = NULL;
+	priv->curr_in_buf = NULL;
+
+	priv->fieldtype = infmt->field;
+
+	/* init the vdi-in channels */
+	ret = setup_vdi_channel(priv, priv->vdi_in_ch_p, 0, 0);
+	if (ret)
+		return ret;
+	ret = setup_vdi_channel(priv, priv->vdi_in_ch, 0, 0);
+	if (ret)
+		return ret;
+	return setup_vdi_channel(priv, priv->vdi_in_ch_n, 0, 0);
+}
+
+static void vdic_start_indirect(struct vdic_priv *priv)
+{
+	/* enable the channels */
+	ipu_idmac_enable_channel(priv->vdi_in_ch_p);
+	ipu_idmac_enable_channel(priv->vdi_in_ch);
+	ipu_idmac_enable_channel(priv->vdi_in_ch_n);
+}
+
+static void vdic_stop_indirect(struct vdic_priv *priv)
+{
+	/* disable channels */
+	ipu_idmac_disable_channel(priv->vdi_in_ch_p);
+	ipu_idmac_disable_channel(priv->vdi_in_ch);
+	ipu_idmac_disable_channel(priv->vdi_in_ch_n);
+}
+
+static void vdic_disable_indirect(struct vdic_priv *priv)
+{
+}
+
+static struct vdic_pipeline_ops direct_ops = {
+	.setup = vdic_setup_direct,
+	.start = vdic_start_direct,
+	.stop = vdic_stop_direct,
+	.disable = vdic_disable_direct,
+};
+
+static struct vdic_pipeline_ops indirect_ops = {
+	.setup = vdic_setup_indirect,
+	.start = vdic_start_indirect,
+	.stop = vdic_stop_indirect,
+	.disable = vdic_disable_indirect,
+};
+
+static int vdic_start(struct vdic_priv *priv)
+{
+	struct v4l2_mbus_framefmt *infmt;
+	int ret;
+
+	infmt = &priv->format_mbus[priv->active_input_pad];
+
+	priv->ops = priv->csi_direct ? &direct_ops : &indirect_ops;
+
+	ret = vdic_get_ipu_resources(priv);
+	if (ret)
+		return ret;
+
+	/*
+	 * init the VDIC.
+	 *
+	 * note we don't give infmt->code to ipu_vdi_setup(). The VDIC
+	 * only supports 4:2:2 or 4:2:0, and this subdev will only
+	 * negotiate 4:2:2 at its sink pads.
+	 */
+	ipu_vdi_setup(priv->vdi, MEDIA_BUS_FMT_UYVY8_2X8,
+		      infmt->width, infmt->height);
+	ipu_vdi_set_field_order(priv->vdi, V4L2_STD_UNKNOWN, infmt->field);
+	ipu_vdi_set_motion(priv->vdi, priv->motion);
+
+	ret = priv->ops->setup(priv);
+	if (ret)
+		goto out_put_ipu;
+
+	ipu_vdi_enable(priv->vdi);
+
+	priv->ops->start(priv);
+
+	return 0;
+
+out_put_ipu:
+	vdic_put_ipu_resources(priv);
+	return ret;
+}
+
+static void vdic_stop(struct vdic_priv *priv)
+{
+	priv->ops->stop(priv);
+	ipu_vdi_disable(priv->vdi);
+	priv->ops->disable(priv);
+
+	vdic_put_ipu_resources(priv);
+}
+
+/*
+ * V4L2 subdev operations.
+ */
+
+static int vdic_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct vdic_priv *priv = container_of(ctrl->handler,
+					      struct vdic_priv, ctrl_hdlr);
+	enum ipu_motion_sel motion;
+	int ret = 0;
+
+	mutex_lock(&priv->lock);
+
+	switch (ctrl->id) {
+	case V4L2_CID_DEINTERLACING_MODE:
+		motion = ctrl->val;
+		if (motion != priv->motion) {
+			/* can't change motion control mid-streaming */
+			if (priv->stream_on) {
+				ret = -EBUSY;
+				goto out;
+			}
+			priv->motion = motion;
+		}
+		break;
+	default:
+		v4l2_err(&priv->sd, "Invalid control\n");
+		ret = -EINVAL;
+	}
+
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static const struct v4l2_ctrl_ops vdic_ctrl_ops = {
+	.s_ctrl = vdic_s_ctrl,
+};
+
+static const char * const vdic_ctrl_motion_menu[] = {
+	"No Motion Compensation",
+	"Low Motion",
+	"Medium Motion",
+	"High Motion",
+};
+
+static int vdic_init_controls(struct vdic_priv *priv)
+{
+	struct v4l2_ctrl_handler *hdlr = &priv->ctrl_hdlr;
+	int ret;
+
+	v4l2_ctrl_handler_init(hdlr, 1);
+
+	v4l2_ctrl_new_std_menu_items(hdlr, &vdic_ctrl_ops,
+				     V4L2_CID_DEINTERLACING_MODE,
+				     HIGH_MOTION, 0, HIGH_MOTION,
+				     vdic_ctrl_motion_menu);
+
+	priv->sd.ctrl_handler = hdlr;
+
+	if (hdlr->error) {
+		ret = hdlr->error;
+		goto out_free;
+	}
+
+	v4l2_ctrl_handler_setup(hdlr);
+	return 0;
+
+out_free:
+	v4l2_ctrl_handler_free(hdlr);
+	return ret;
+}
+
+static int vdic_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
+	int ret = 0;
+
+	mutex_lock(&priv->lock);
+
+	if (!priv->src || !priv->sink_sd) {
+		ret = -EPIPE;
+		goto out;
+	}
+
+	dev_dbg(priv->dev, "stream %s\n", enable ? "ON" : "OFF");
+
+	if (enable && !priv->stream_on)
+		ret = vdic_start(priv);
+	else if (!enable && priv->stream_on)
+		vdic_stop(priv);
+
+	if (!ret)
+		priv->stream_on = enable;
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int vdic_enum_mbus_code(struct v4l2_subdev *sd,
+			       struct v4l2_subdev_pad_config *cfg,
+			       struct v4l2_subdev_mbus_code_enum *code)
+{
+	if (code->pad >= VDIC_NUM_PADS)
+		return -EINVAL;
+
+	if (code->pad == VDIC_SINK_PAD_IDMAC)
+		return imx_media_enum_format(NULL, &code->code, code->index,
+					     false, false);
+
+	return imx_media_enum_ipu_format(NULL, &code->code, code->index, false);
+}
+
+static struct v4l2_mbus_framefmt *
+__vdic_get_fmt(struct vdic_priv *priv, struct v4l2_subdev_pad_config *cfg,
+	       unsigned int pad, enum v4l2_subdev_format_whence which)
+{
+	if (which == V4L2_SUBDEV_FORMAT_TRY)
+		return v4l2_subdev_get_try_format(&priv->sd, cfg, pad);
+	else
+		return &priv->format_mbus[pad];
+}
+
+static int vdic_get_fmt(struct v4l2_subdev *sd,
+			struct v4l2_subdev_pad_config *cfg,
+			struct v4l2_subdev_format *sdformat)
+{
+	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_mbus_framefmt *fmt;
+	int ret = 0;
+
+	if (sdformat->pad >= VDIC_NUM_PADS)
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	fmt = __vdic_get_fmt(priv, cfg, sdformat->pad, sdformat->which);
+	if (!fmt) {
+		ret = -EINVAL;
+		goto out;
+	}
+
+	sdformat->format = *fmt;
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int vdic_set_fmt(struct v4l2_subdev *sd,
+			struct v4l2_subdev_pad_config *cfg,
+			struct v4l2_subdev_format *sdformat)
+{
+	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
+	const struct imx_media_pixfmt *cc;
+	struct v4l2_mbus_framefmt *infmt;
+	int ret = 0;
+	u32 code;
+
+	if (sdformat->pad >= VDIC_NUM_PADS)
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	if (priv->stream_on) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W_VDIC,
+			      W_ALIGN, &sdformat->format.height,
+			      MIN_H, MAX_H_VDIC, H_ALIGN, S_ALIGN);
+
+	switch (sdformat->pad) {
+	case VDIC_SRC_PAD_DIRECT:
+		infmt = __vdic_get_fmt(priv, cfg, priv->active_input_pad,
+				       sdformat->which);
+
+		cc = imx_media_find_ipu_format(0, sdformat->format.code, false);
+		if (!cc) {
+			imx_media_enum_ipu_format(NULL, &code, 0, false);
+			cc = imx_media_find_ipu_format(0, code, false);
+			sdformat->format.code = cc->codes[0];
+		}
+
+		sdformat->format.width = infmt->width;
+		sdformat->format.height = infmt->height;
+		/* output is always progressive! */
+		sdformat->format.field = V4L2_FIELD_NONE;
+		break;
+	case VDIC_SINK_PAD_IDMAC:
+	case VDIC_SINK_PAD_DIRECT:
+		if (sdformat->pad == VDIC_SINK_PAD_DIRECT) {
+			cc = imx_media_find_ipu_format(0, sdformat->format.code,
+						       false);
+			if (!cc) {
+				imx_media_enum_ipu_format(NULL, &code, 0,
+							  false);
+				cc = imx_media_find_ipu_format(0, code, false);
+				sdformat->format.code = cc->codes[0];
+			}
+		} else {
+			cc = imx_media_find_format(0, sdformat->format.code,
+						   false, false);
+			if (!cc) {
+				imx_media_enum_format(NULL, &code, 0,
+						      false, false);
+				cc = imx_media_find_format(0, code,
+							   false, false);
+				sdformat->format.code = cc->codes[0];
+			}
+		}
+
+		/* input must be interlaced! Choose SEQ_TB if not */
+		if (!V4L2_FIELD_HAS_BOTH(sdformat->format.field))
+			sdformat->format.field = V4L2_FIELD_SEQ_TB;
+		break;
+	default:
+		ret = -EINVAL;
+		goto out;
+	}
+
+	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
+		cfg->try_fmt = sdformat->format;
+	} else {
+		priv->format_mbus[sdformat->pad] = sdformat->format;
+		priv->cc[sdformat->pad] = cc;
+	}
+
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int vdic_g_frame_interval(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_frame_interval *fi)
+{
+	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
+
+	mutex_lock(&priv->lock);
+	fi->interval = priv->frame_interval;
+	mutex_unlock(&priv->lock);
+
+	return 0;
+}
+
+static int vdic_s_frame_interval(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_frame_interval *fi)
+{
+	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
+
+	mutex_lock(&priv->lock);
+
+	/* Output pads mirror active input pad, no limits on input pads */
+	if (fi->pad == VDIC_SRC_PAD_DIRECT)
+		fi->interval = priv->frame_interval;
+
+	priv->frame_interval = fi->interval;
+
+	mutex_unlock(&priv->lock);
+
+	return 0;
+}
+
+static int vdic_link_setup(struct media_entity *entity,
+			    const struct media_pad *local,
+			    const struct media_pad *remote, u32 flags)
+{
+	struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity);
+	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_subdev *remote_sd;
+	int ret = 0;
+
+	dev_dbg(priv->dev, "link setup %s -> %s", remote->entity->name,
+		local->entity->name);
+
+	mutex_lock(&priv->lock);
+
+	if (local->flags & MEDIA_PAD_FL_SOURCE) {
+		if (!is_media_entity_v4l2_subdev(remote->entity)) {
+			ret = -EINVAL;
+			goto out;
+		}
+
+		remote_sd = media_entity_to_v4l2_subdev(remote->entity);
+
+		if (flags & MEDIA_LNK_FL_ENABLED) {
+			if (priv->sink_sd) {
+				ret = -EBUSY;
+				goto out;
+			}
+			priv->sink_sd = remote_sd;
+		} else {
+			priv->sink_sd = NULL;
+		}
+
+		goto out;
+	}
+
+	/* this is a sink pad */
+
+	if (flags & MEDIA_LNK_FL_ENABLED) {
+		if (priv->src) {
+			ret = -EBUSY;
+			goto out;
+		}
+	} else {
+		priv->src = NULL;
+		goto out;
+	}
+
+	if (local->index == VDIC_SINK_PAD_IDMAC) {
+		struct imx_media_video_dev *vdev = priv->vdev;
+
+		if (!is_media_entity_v4l2_video_device(remote->entity)) {
+			ret = -EINVAL;
+			goto out;
+		}
+		if (!vdev) {
+			ret = -ENODEV;
+			goto out;
+		}
+
+		priv->csi_direct = false;
+	} else {
+		if (!is_media_entity_v4l2_subdev(remote->entity)) {
+			ret = -EINVAL;
+			goto out;
+		}
+
+		remote_sd = media_entity_to_v4l2_subdev(remote->entity);
+
+		/* direct pad must connect to a CSI */
+		if (!(remote_sd->grp_id & IMX_MEDIA_GRP_ID_CSI) ||
+		    remote->index != CSI_SRC_PAD_DIRECT) {
+			ret = -EINVAL;
+			goto out;
+		}
+
+		priv->csi_direct = true;
+	}
+
+	priv->src = remote->entity;
+	/* record which input pad is now active */
+	priv->active_input_pad = local->index;
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int vdic_link_validate(struct v4l2_subdev *sd,
+			      struct media_link *link,
+			      struct v4l2_subdev_format *source_fmt,
+			      struct v4l2_subdev_format *sink_fmt)
+{
+	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
+	int ret;
+
+	ret = v4l2_subdev_link_validate_default(sd, link,
+						source_fmt, sink_fmt);
+	if (ret)
+		return ret;
+
+	ret = v4l2_subdev_link_validate_frame_interval(link);
+	if (ret)
+		return ret;
+
+	mutex_lock(&priv->lock);
+
+	if (priv->csi_direct && priv->motion != HIGH_MOTION) {
+		v4l2_err(&priv->sd,
+			 "direct CSI pipeline requires high motion\n");
+		ret = -EINVAL;
+	}
+
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+/*
+ * retrieve our pads parsed from the OF graph by the media device
+ */
+static int vdic_registered(struct v4l2_subdev *sd)
+{
+	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
+	int i, ret;
+	u32 code;
+
+	/* get media device */
+	priv->md = dev_get_drvdata(sd->v4l2_dev->dev);
+
+	for (i = 0; i < VDIC_NUM_PADS; i++) {
+		priv->pad[i].flags = (i == VDIC_SRC_PAD_DIRECT) ?
+			MEDIA_PAD_FL_SOURCE : MEDIA_PAD_FL_SINK;
+
+		code = 0;
+		if (i != VDIC_SINK_PAD_IDMAC)
+			imx_media_enum_ipu_format(NULL, &code, 0, true);
+
+		/* set a default mbus format  */
+		ret = imx_media_init_mbus_fmt(&priv->format_mbus[i],
+					      640, 480, code, V4L2_FIELD_NONE,
+					      &priv->cc[i]);
+		if (ret)
+			return ret;
+	}
+
+	/* init default frame interval */
+	priv->frame_interval.numerator = 1;
+	priv->frame_interval.denominator = 30;
+
+	priv->active_input_pad = VDIC_SINK_PAD_DIRECT;
+
+	ret = vdic_init_controls(priv);
+	if (ret)
+		return ret;
+
+	ret = media_entity_pads_init(&sd->entity, VDIC_NUM_PADS, priv->pad);
+	if (ret)
+		v4l2_ctrl_handler_free(&priv->ctrl_hdlr);
+
+	return ret;
+}
+
+static void vdic_unregistered(struct v4l2_subdev *sd)
+{
+	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
+
+	v4l2_ctrl_handler_free(&priv->ctrl_hdlr);
+}
+
+static struct v4l2_subdev_pad_ops vdic_pad_ops = {
+	.enum_mbus_code = vdic_enum_mbus_code,
+	.get_fmt = vdic_get_fmt,
+	.set_fmt = vdic_set_fmt,
+	.link_validate = vdic_link_validate,
+};
+
+static struct v4l2_subdev_video_ops vdic_video_ops = {
+	.s_stream = vdic_s_stream,
+	.g_frame_interval = vdic_g_frame_interval,
+	.s_frame_interval = vdic_s_frame_interval,
+};
+
+static struct media_entity_operations vdic_entity_ops = {
+	.link_setup = vdic_link_setup,
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static struct v4l2_subdev_ops vdic_subdev_ops = {
+	.video = &vdic_video_ops,
+	.pad = &vdic_pad_ops,
+};
+
+static struct v4l2_subdev_internal_ops vdic_internal_ops = {
+	.registered = vdic_registered,
+	.unregistered = vdic_unregistered,
+};
+
+static int imx_vdic_probe(struct platform_device *pdev)
+{
+	struct imx_media_internal_sd_platformdata *pdata;
+	struct vdic_priv *priv;
+	int ret;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, &priv->sd);
+	priv->dev = &pdev->dev;
+
+	pdata = priv->dev->platform_data;
+	priv->ipu_id = pdata->ipu_id;
+
+	v4l2_subdev_init(&priv->sd, &vdic_subdev_ops);
+	v4l2_set_subdevdata(&priv->sd, priv);
+	priv->sd.internal_ops = &vdic_internal_ops;
+	priv->sd.entity.ops = &vdic_entity_ops;
+	priv->sd.entity.function = MEDIA_ENT_F_PROC_VIDEO_PIXEL_FORMATTER;
+	priv->sd.dev = &pdev->dev;
+	priv->sd.owner = THIS_MODULE;
+	priv->sd.flags = V4L2_SUBDEV_FL_HAS_DEVNODE;
+	/* get our group id */
+	priv->sd.grp_id = pdata->grp_id;
+	strncpy(priv->sd.name, pdata->sd_name, sizeof(priv->sd.name));
+
+	mutex_init(&priv->lock);
+
+	ret = v4l2_async_register_subdev(&priv->sd);
+	if (ret)
+		goto free;
+
+	return 0;
+free:
+	mutex_destroy(&priv->lock);
+	return ret;
+}
+
+static int imx_vdic_remove(struct platform_device *pdev)
+{
+	struct v4l2_subdev *sd = platform_get_drvdata(pdev);
+	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
+
+	v4l2_info(sd, "Removing\n");
+
+	v4l2_async_unregister_subdev(sd);
+	mutex_destroy(&priv->lock);
+	media_entity_cleanup(&sd->entity);
+
+	return 0;
+}
+
+static const struct platform_device_id imx_vdic_ids[] = {
+	{ .name = "imx-ipuv3-vdic" },
+	{ },
+};
+MODULE_DEVICE_TABLE(platform, imx_vdic_ids);
+
+static struct platform_driver imx_vdic_driver = {
+	.probe = imx_vdic_probe,
+	.remove = imx_vdic_remove,
+	.id_table = imx_vdic_ids,
+	.driver = {
+		.name = "imx-ipuv3-vdic",
+	},
+};
+module_platform_driver(imx_vdic_driver);
+
+MODULE_DESCRIPTION("i.MX VDIC subdev driver");
+MODULE_AUTHOR("Steve Longerbeam <steve_longerbeam@mentor.com>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:imx-ipuv3-vdic");
-- 
2.7.4

[PATCH v5 27/39] media: imx: Add IC subdev drivers

[Steve Longerbeam]

This is a set of three media entity subdevice drivers for the i.MX
Image Converter:

- Pre-process Router: Takes input frames from CSI0, CSI1, or VDIC.
  Two output pads enable either or both of the preprocess tasks
  below. If the input is from one of the CSIs, both proprocess task
  links can be enabled to process frames from that CSI simultaneously.
  If the input is the VDIC, only the Pre-processing Viewfinder task
  link can be enabled.

- Pre-processing Encode task: video frames are routed directly from
  the CSI and can be scaled, color-space converted, and rotated.
  Scaled output is limited to 1024x1024 resolution. Output frames
  are routed to the capture device.

- Pre-processing Viewfinder task: this task can perform the same
  conversions as the pre-process encode task, but in addition can
  be used for hardware motion compensated deinterlacing. Frames can
  come either directly from the CSI or from the VDIC. Scaled output
  is limited to 1024x1024 resolution. Output frames are routed to
  the capture device.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/Makefile          |    2 +
 drivers/staging/media/imx/imx-ic-common.c   |  113 +++
 drivers/staging/media/imx/imx-ic-prp.c      |  475 +++++++++++
 drivers/staging/media/imx/imx-ic-prpencvf.c | 1219 +++++++++++++++++++++++++++
 drivers/staging/media/imx/imx-ic.h          |   38 +
 5 files changed, 1847 insertions(+)
 create mode 100644 drivers/staging/media/imx/imx-ic-common.c
 create mode 100644 drivers/staging/media/imx/imx-ic-prp.c
 create mode 100644 drivers/staging/media/imx/imx-ic-prpencvf.c
 create mode 100644 drivers/staging/media/imx/imx-ic.h

diff --git a/drivers/staging/media/imx/Makefile b/drivers/staging/media/imx/Makefile
index 1f01520..878a126 100644
--- a/drivers/staging/media/imx/Makefile
+++ b/drivers/staging/media/imx/Makefile
@@ -1,9 +1,11 @@
 imx-media-objs := imx-media-dev.o imx-media-internal-sd.o imx-media-of.o
 imx-media-common-objs := imx-media-utils.o imx-media-fim.o
+imx-media-ic-objs := imx-ic-common.o imx-ic-prp.o imx-ic-prpencvf.o
 
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-common.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-capture.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-vdic.o
+obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-ic.o
 
 obj-$(CONFIG_VIDEO_IMX_CSI) += imx-media-csi.o
diff --git a/drivers/staging/media/imx/imx-ic-common.c b/drivers/staging/media/imx/imx-ic-common.c
new file mode 100644
index 0000000..cfdd490
--- /dev/null
+++ b/drivers/staging/media/imx/imx-ic-common.c
@@ -0,0 +1,113 @@
+/*
+ * V4L2 Image Converter Subdev for Freescale i.MX5/6 SOC
+ *
+ * Copyright (c) 2014-2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-subdev.h>
+#include "imx-media.h"
+#include "imx-ic.h"
+
+#define IC_TASK_PRP IC_NUM_TASKS
+#define IC_NUM_OPS  (IC_NUM_TASKS + 1)
+
+static struct imx_ic_ops *ic_ops[IC_NUM_OPS] = {
+	[IC_TASK_PRP]            = &imx_ic_prp_ops,
+	[IC_TASK_ENCODER]        = &imx_ic_prpencvf_ops,
+	[IC_TASK_VIEWFINDER]     = &imx_ic_prpencvf_ops,
+};
+
+static int imx_ic_probe(struct platform_device *pdev)
+{
+	struct imx_media_internal_sd_platformdata *pdata;
+	struct imx_ic_priv *priv;
+	int ret;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, &priv->sd);
+	priv->dev = &pdev->dev;
+
+	/* get our ipu_id, grp_id and IC task id */
+	pdata = priv->dev->platform_data;
+	priv->ipu_id = pdata->ipu_id;
+	switch (pdata->grp_id) {
+	case IMX_MEDIA_GRP_ID_IC_PRP:
+		priv->task_id = IC_TASK_PRP;
+		break;
+	case IMX_MEDIA_GRP_ID_IC_PRPENC:
+		priv->task_id = IC_TASK_ENCODER;
+		break;
+	case IMX_MEDIA_GRP_ID_IC_PRPVF:
+		priv->task_id = IC_TASK_VIEWFINDER;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	v4l2_subdev_init(&priv->sd, ic_ops[priv->task_id]->subdev_ops);
+	v4l2_set_subdevdata(&priv->sd, priv);
+	priv->sd.internal_ops = ic_ops[priv->task_id]->internal_ops;
+	priv->sd.entity.ops = ic_ops[priv->task_id]->entity_ops;
+	priv->sd.entity.function = MEDIA_ENT_F_PROC_VIDEO_SCALER;
+	priv->sd.dev = &pdev->dev;
+	priv->sd.owner = THIS_MODULE;
+	priv->sd.flags = V4L2_SUBDEV_FL_HAS_DEVNODE | V4L2_SUBDEV_FL_HAS_EVENTS;
+	priv->sd.grp_id = pdata->grp_id;
+	strncpy(priv->sd.name, pdata->sd_name, sizeof(priv->sd.name));
+
+	ret = ic_ops[priv->task_id]->init(priv);
+	if (ret)
+		return ret;
+
+	ret = v4l2_async_register_subdev(&priv->sd);
+	if (ret)
+		ic_ops[priv->task_id]->remove(priv);
+
+	return ret;
+}
+
+static int imx_ic_remove(struct platform_device *pdev)
+{
+	struct v4l2_subdev *sd = platform_get_drvdata(pdev);
+	struct imx_ic_priv *priv = container_of(sd, struct imx_ic_priv, sd);
+
+	v4l2_info(sd, "Removing\n");
+
+	ic_ops[priv->task_id]->remove(priv);
+
+	v4l2_async_unregister_subdev(sd);
+	media_entity_cleanup(&sd->entity);
+
+	return 0;
+}
+
+static const struct platform_device_id imx_ic_ids[] = {
+	{ .name = "imx-ipuv3-ic" },
+	{ },
+};
+MODULE_DEVICE_TABLE(platform, imx_ic_ids);
+
+static struct platform_driver imx_ic_driver = {
+	.probe = imx_ic_probe,
+	.remove = imx_ic_remove,
+	.id_table = imx_ic_ids,
+	.driver = {
+		.name = "imx-ipuv3-ic",
+	},
+};
+module_platform_driver(imx_ic_driver);
+
+MODULE_DESCRIPTION("i.MX IC subdev driver");
+MODULE_AUTHOR("Steve Longerbeam <steve_longerbeam@mentor.com>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:imx-ipuv3-ic");
diff --git a/drivers/staging/media/imx/imx-ic-prp.c b/drivers/staging/media/imx/imx-ic-prp.c
new file mode 100644
index 0000000..1832915
--- /dev/null
+++ b/drivers/staging/media/imx/imx-ic-prp.c
@@ -0,0 +1,475 @@
+/*
+ * V4L2 Capture IC Preprocess Subdev for Freescale i.MX5/6 SOC
+ *
+ * This subdevice handles capture of video frames from the CSI or VDIC,
+ * which are routed directly to the Image Converter preprocess tasks,
+ * for resizing, colorspace conversion, and rotation.
+ *
+ * Copyright (c) 2012-2017 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/timer.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-ioctl.h>
+#include <media/v4l2-subdev.h>
+#include <media/imx.h>
+#include "imx-media.h"
+#include "imx-ic.h"
+
+/*
+ * Min/Max supported width and heights.
+ */
+#define MIN_W       176
+#define MIN_H       144
+#define MAX_W      4096
+#define MAX_H      4096
+#define W_ALIGN    4 /* multiple of 16 pixels */
+#define H_ALIGN    1 /* multiple of 2 lines */
+#define S_ALIGN    1 /* multiple of 2 */
+
+struct prp_priv {
+	struct imx_media_dev *md;
+	struct imx_ic_priv *ic_priv;
+	struct media_pad pad[PRP_NUM_PADS];
+
+	/* lock to protect all members below */
+	struct mutex lock;
+
+	/* IPU units we require */
+	struct ipu_soc *ipu;
+
+	struct v4l2_subdev *src_sd;
+	struct v4l2_subdev *sink_sd_prpenc;
+	struct v4l2_subdev *sink_sd_prpvf;
+
+	/* the CSI id at link validate */
+	int csi_id;
+
+	struct v4l2_mbus_framefmt format_mbus[PRP_NUM_PADS];
+	const struct imx_media_pixfmt *cc[PRP_NUM_PADS];
+	struct v4l2_fract frame_interval;
+
+	bool stream_on; /* streaming is on */
+};
+
+static inline struct prp_priv *sd_to_priv(struct v4l2_subdev *sd)
+{
+	struct imx_ic_priv *ic_priv = v4l2_get_subdevdata(sd);
+
+	return ic_priv->prp_priv;
+}
+
+static int prp_start(struct prp_priv *priv)
+{
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+
+	priv->ipu = priv->md->ipu[ic_priv->ipu_id];
+
+	/* set IC to receive from CSI or VDI depending on source */
+	if (priv->src_sd->grp_id & IMX_MEDIA_GRP_ID_VDIC)
+		ipu_set_ic_src_mux(priv->ipu, 0, true);
+	else
+		ipu_set_ic_src_mux(priv->ipu, priv->csi_id, false);
+
+	return 0;
+}
+
+static void prp_stop(struct prp_priv *priv)
+{
+}
+
+static int prp_enum_mbus_code(struct v4l2_subdev *sd,
+			      struct v4l2_subdev_pad_config *cfg,
+			      struct v4l2_subdev_mbus_code_enum *code)
+{
+	if (code->pad >= PRP_NUM_PADS)
+		return -EINVAL;
+
+	return imx_media_enum_ipu_format(NULL, &code->code, code->index, true);
+}
+
+static struct v4l2_mbus_framefmt *
+__prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_pad_config *cfg,
+	      unsigned int pad, enum v4l2_subdev_format_whence which)
+{
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+
+	if (which == V4L2_SUBDEV_FORMAT_TRY)
+		return v4l2_subdev_get_try_format(&ic_priv->sd, cfg, pad);
+	else
+		return &priv->format_mbus[pad];
+}
+
+/*
+ * V4L2 subdev operations.
+ */
+
+static int prp_get_fmt(struct v4l2_subdev *sd,
+		       struct v4l2_subdev_pad_config *cfg,
+		       struct v4l2_subdev_format *sdformat)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+	struct v4l2_mbus_framefmt *fmt;
+	int ret = 0;
+
+	if (sdformat->pad >= PRP_NUM_PADS)
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	fmt = __prp_get_fmt(priv, cfg, sdformat->pad, sdformat->which);
+	if (!fmt) {
+		ret = -EINVAL;
+		goto out;
+	}
+
+	sdformat->format = *fmt;
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int prp_set_fmt(struct v4l2_subdev *sd,
+		       struct v4l2_subdev_pad_config *cfg,
+		       struct v4l2_subdev_format *sdformat)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+	const struct imx_media_pixfmt *cc = NULL;
+	struct v4l2_mbus_framefmt *infmt;
+	int ret = 0;
+	u32 code;
+
+	if (sdformat->pad >= PRP_NUM_PADS)
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	if (priv->stream_on) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	cc = imx_media_find_ipu_format(0, sdformat->format.code, true);
+	if (!cc) {
+		imx_media_enum_ipu_format(NULL, &code, 0, true);
+		cc = imx_media_find_ipu_format(0, code, true);
+		sdformat->format.code = cc->codes[0];
+	}
+
+	v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
+			      W_ALIGN, &sdformat->format.height,
+			      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
+
+	/* Output pads mirror input pad */
+	if (sdformat->pad == PRP_SRC_PAD_PRPENC ||
+	    sdformat->pad == PRP_SRC_PAD_PRPVF) {
+		infmt = __prp_get_fmt(priv, cfg, PRP_SINK_PAD,
+				      sdformat->which);
+		sdformat->format = *infmt;
+	}
+
+	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
+		cfg->try_fmt = sdformat->format;
+	} else {
+		priv->format_mbus[sdformat->pad] = sdformat->format;
+		priv->cc[sdformat->pad] = cc;
+	}
+
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int prp_g_frame_interval(struct v4l2_subdev *sd,
+				struct v4l2_subdev_frame_interval *fi)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+
+	mutex_lock(&priv->lock);
+	fi->interval = priv->frame_interval;
+	mutex_unlock(&priv->lock);
+
+	return 0;
+}
+
+static int prp_s_frame_interval(struct v4l2_subdev *sd,
+				struct v4l2_subdev_frame_interval *fi)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+
+	mutex_lock(&priv->lock);
+
+	/* Output pads mirror active input pad, no limits on input pads */
+	if (fi->pad != PRP_SINK_PAD)
+		fi->interval = priv->frame_interval;
+
+	priv->frame_interval = fi->interval;
+
+	mutex_unlock(&priv->lock);
+
+	return 0;
+}
+
+static int prp_link_setup(struct media_entity *entity,
+			  const struct media_pad *local,
+			  const struct media_pad *remote, u32 flags)
+{
+	struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity);
+	struct imx_ic_priv *ic_priv = v4l2_get_subdevdata(sd);
+	struct prp_priv *priv = ic_priv->prp_priv;
+	struct v4l2_subdev *remote_sd;
+	int ret = 0;
+
+	dev_dbg(ic_priv->dev, "link setup %s -> %s", remote->entity->name,
+		local->entity->name);
+
+	remote_sd = media_entity_to_v4l2_subdev(remote->entity);
+
+	mutex_lock(&priv->lock);
+
+	if (local->flags & MEDIA_PAD_FL_SINK) {
+		if (flags & MEDIA_LNK_FL_ENABLED) {
+			if (priv->src_sd) {
+				ret = -EBUSY;
+				goto out;
+			}
+			if (priv->sink_sd_prpenc && (remote_sd->grp_id &
+						     IMX_MEDIA_GRP_ID_VDIC)) {
+				ret = -EINVAL;
+				goto out;
+			}
+			priv->src_sd = remote_sd;
+		} else {
+			priv->src_sd = NULL;
+		}
+
+		goto out;
+	}
+
+	/* this is a source pad */
+	if (flags & MEDIA_LNK_FL_ENABLED) {
+		switch (local->index) {
+		case PRP_SRC_PAD_PRPENC:
+			if (priv->sink_sd_prpenc) {
+				ret = -EBUSY;
+				goto out;
+			}
+			if (priv->src_sd && (priv->src_sd->grp_id &
+					     IMX_MEDIA_GRP_ID_VDIC)) {
+				ret = -EINVAL;
+				goto out;
+			}
+			priv->sink_sd_prpenc = remote_sd;
+			break;
+		case PRP_SRC_PAD_PRPVF:
+			if (priv->sink_sd_prpvf) {
+				ret = -EBUSY;
+				goto out;
+			}
+			priv->sink_sd_prpvf = remote_sd;
+			break;
+		default:
+			ret = -EINVAL;
+		}
+	} else {
+		switch (local->index) {
+		case PRP_SRC_PAD_PRPENC:
+			priv->sink_sd_prpenc = NULL;
+			break;
+		case PRP_SRC_PAD_PRPVF:
+			priv->sink_sd_prpvf = NULL;
+			break;
+		default:
+			ret = -EINVAL;
+		}
+	}
+
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int prp_link_validate(struct v4l2_subdev *sd,
+			     struct media_link *link,
+			     struct v4l2_subdev_format *source_fmt,
+			     struct v4l2_subdev_format *sink_fmt)
+{
+	struct imx_ic_priv *ic_priv = v4l2_get_subdevdata(sd);
+	struct prp_priv *priv = ic_priv->prp_priv;
+	struct imx_media_subdev *csi;
+	int ret;
+
+	ret = v4l2_subdev_link_validate_default(sd, link,
+						source_fmt, sink_fmt);
+	if (ret)
+		return ret;
+
+	ret = v4l2_subdev_link_validate_frame_interval(link);
+	if (ret)
+		return ret;
+
+	csi = imx_media_find_pipeline_subdev(priv->md, &ic_priv->sd.entity,
+					     IMX_MEDIA_GRP_ID_CSI);
+	if (IS_ERR(csi))
+		csi = NULL;
+
+	mutex_lock(&priv->lock);
+
+	if (priv->src_sd->grp_id & IMX_MEDIA_GRP_ID_VDIC) {
+		/*
+		 * the ->PRPENC link cannot be enabled if the source
+		 * is the VDIC
+		 */
+		if (priv->sink_sd_prpenc)
+			ret = -EINVAL;
+		goto out;
+	} else {
+		/* the source is a CSI */
+		if (!csi) {
+			ret = -EINVAL;
+			goto out;
+		}
+
+		switch (csi->sd->grp_id) {
+		case IMX_MEDIA_GRP_ID_CSI0:
+			priv->csi_id = 0;
+			break;
+		case IMX_MEDIA_GRP_ID_CSI1:
+			priv->csi_id = 1;
+			break;
+		default:
+			ret = -EINVAL;
+		}
+	}
+
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int prp_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct imx_ic_priv *ic_priv = v4l2_get_subdevdata(sd);
+	struct prp_priv *priv = ic_priv->prp_priv;
+	int ret = 0;
+
+	mutex_lock(&priv->lock);
+
+	if (!priv->src_sd || (!priv->sink_sd_prpenc && !priv->sink_sd_prpvf)) {
+		ret = -EPIPE;
+		goto out;
+	}
+
+	dev_dbg(ic_priv->dev, "stream %s\n", enable ? "ON" : "OFF");
+
+	if (enable && !priv->stream_on)
+		ret = prp_start(priv);
+	else if (!enable && priv->stream_on)
+		prp_stop(priv);
+
+	if (!ret)
+		priv->stream_on = enable;
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+/*
+ * retrieve our pads parsed from the OF graph by the media device
+ */
+static int prp_registered(struct v4l2_subdev *sd)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+	int i, ret;
+	u32 code;
+
+	/* get media device */
+	priv->md = dev_get_drvdata(sd->v4l2_dev->dev);
+
+	for (i = 0; i < PRP_NUM_PADS; i++) {
+		priv->pad[i].flags = (i == PRP_SINK_PAD) ?
+			MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
+
+		/* set a default mbus format  */
+		imx_media_enum_ipu_format(NULL, &code, 0, true);
+		ret = imx_media_init_mbus_fmt(&priv->format_mbus[i],
+					      640, 480, code, V4L2_FIELD_NONE,
+					      &priv->cc[i]);
+		if (ret)
+			return ret;
+	}
+
+	/* init default frame interval */
+	priv->frame_interval.numerator = 1;
+	priv->frame_interval.denominator = 30;
+
+	return media_entity_pads_init(&sd->entity, PRP_NUM_PADS, priv->pad);
+}
+
+static struct v4l2_subdev_pad_ops prp_pad_ops = {
+	.enum_mbus_code = prp_enum_mbus_code,
+	.get_fmt = prp_get_fmt,
+	.set_fmt = prp_set_fmt,
+	.link_validate = prp_link_validate,
+};
+
+static struct v4l2_subdev_video_ops prp_video_ops = {
+	.s_stream = prp_s_stream,
+	.g_frame_interval = prp_g_frame_interval,
+	.s_frame_interval = prp_s_frame_interval,
+};
+
+static struct media_entity_operations prp_entity_ops = {
+	.link_setup = prp_link_setup,
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static struct v4l2_subdev_ops prp_subdev_ops = {
+	.video = &prp_video_ops,
+	.pad = &prp_pad_ops,
+};
+
+static struct v4l2_subdev_internal_ops prp_internal_ops = {
+	.registered = prp_registered,
+};
+
+static int prp_init(struct imx_ic_priv *ic_priv)
+{
+	struct prp_priv *priv;
+
+	priv = devm_kzalloc(ic_priv->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	mutex_init(&priv->lock);
+	ic_priv->prp_priv = priv;
+	priv->ic_priv = ic_priv;
+
+	return 0;
+}
+
+static void prp_remove(struct imx_ic_priv *ic_priv)
+{
+	struct prp_priv *priv = ic_priv->prp_priv;
+
+	mutex_destroy(&priv->lock);
+}
+
+struct imx_ic_ops imx_ic_prp_ops = {
+	.subdev_ops = &prp_subdev_ops,
+	.internal_ops = &prp_internal_ops,
+	.entity_ops = &prp_entity_ops,
+	.init = prp_init,
+	.remove = prp_remove,
+};
diff --git a/drivers/staging/media/imx/imx-ic-prpencvf.c b/drivers/staging/media/imx/imx-ic-prpencvf.c
new file mode 100644
index 0000000..bd89e9b
--- /dev/null
+++ b/drivers/staging/media/imx/imx-ic-prpencvf.c
@@ -0,0 +1,1219 @@
+/*
+ * V4L2 Capture IC Preprocess Subdev for Freescale i.MX5/6 SOC
+ *
+ * This subdevice handles capture of video frames from the CSI or VDIC,
+ * which are routed directly to the Image Converter preprocess tasks,
+ * for resizing, colorspace conversion, and rotation.
+ *
+ * Copyright (c) 2012-2017 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/timer.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-ioctl.h>
+#include <media/v4l2-mc.h>
+#include <media/v4l2-subdev.h>
+#include <media/imx.h>
+#include "imx-media.h"
+#include "imx-ic.h"
+
+/*
+ * Min/Max supported width and heights.
+ *
+ * We allow planar output, so we have to align width at the source pad
+ * by 16 pixels to meet IDMAC alignment requirements for possible planar
+ * output.
+ *
+ * TODO: move this into pad format negotiation, if capture device
+ * has not requested a planar format, we should allow 8 pixel
+ * alignment at the source pad.
+ */
+#define MIN_W_SINK  176
+#define MIN_H_SINK  144
+#define MAX_W_SINK 4096
+#define MAX_H_SINK 4096
+#define W_ALIGN_SINK  3 /* multiple of 8 pixels */
+#define H_ALIGN_SINK  1 /* multiple of 2 lines */
+
+#define MAX_W_SRC  1024
+#define MAX_H_SRC  1024
+#define W_ALIGN_SRC   4 /* multiple of 16 pixels */
+#define H_ALIGN_SRC   1 /* multiple of 2 lines */
+
+#define S_ALIGN       1 /* multiple of 2 */
+
+struct prp_priv {
+	struct imx_media_dev *md;
+	struct imx_ic_priv *ic_priv;
+	struct media_pad pad[PRPENCVF_NUM_PADS];
+	/* the video device at output pad */
+	struct imx_media_video_dev *vdev;
+
+	/* lock to protect all members below */
+	struct mutex lock;
+
+	/* IPU units we require */
+	struct ipu_soc *ipu;
+	struct ipu_ic *ic;
+	struct ipuv3_channel *out_ch;
+	struct ipuv3_channel *rot_in_ch;
+	struct ipuv3_channel *rot_out_ch;
+
+	/* active vb2 buffers to send to video dev sink */
+	struct imx_media_buffer *active_vb2_buf[2];
+	struct imx_media_dma_buf underrun_buf;
+
+	int ipu_buf_num;  /* ipu double buffer index: 0-1 */
+
+	/* the sink for the captured frames */
+	struct media_entity *sink;
+	/* the source subdev */
+	struct v4l2_subdev *src_sd;
+
+	/* the attached CSI at stream on */
+	struct v4l2_subdev *csi_sd;
+
+	struct v4l2_mbus_framefmt format_mbus[PRPENCVF_NUM_PADS];
+	const struct imx_media_pixfmt *cc[PRPENCVF_NUM_PADS];
+	struct v4l2_fract frame_interval;
+
+	struct imx_media_dma_buf rot_buf[2];
+
+	/* controls */
+	struct v4l2_ctrl_handler ctrl_hdlr;
+	int  rotation; /* degrees */
+	bool hflip;
+	bool vflip;
+
+	/* derived from rotation, hflip, vflip controls */
+	enum ipu_rotate_mode rot_mode;
+
+	spinlock_t irqlock; /* protect eof_irq handler */
+
+	struct timer_list eof_timeout_timer;
+	int eof_irq;
+	int nfb4eof_irq;
+
+	bool stream_on; /* streaming is on */
+	bool last_eof;  /* waiting for last EOF at stream off */
+	struct completion last_eof_comp;
+};
+
+static const struct prp_channels {
+	u32 out_ch;
+	u32 rot_in_ch;
+	u32 rot_out_ch;
+} prp_channel[] = {
+	[IC_TASK_ENCODER] = {
+		.out_ch = IPUV3_CHANNEL_IC_PRP_ENC_MEM,
+		.rot_in_ch = IPUV3_CHANNEL_MEM_ROT_ENC,
+		.rot_out_ch = IPUV3_CHANNEL_ROT_ENC_MEM,
+	},
+	[IC_TASK_VIEWFINDER] = {
+		.out_ch = IPUV3_CHANNEL_IC_PRP_VF_MEM,
+		.rot_in_ch = IPUV3_CHANNEL_MEM_ROT_VF,
+		.rot_out_ch = IPUV3_CHANNEL_ROT_VF_MEM,
+	},
+};
+
+static inline struct prp_priv *sd_to_priv(struct v4l2_subdev *sd)
+{
+	struct imx_ic_priv *ic_priv = v4l2_get_subdevdata(sd);
+
+	return ic_priv->task_priv;
+}
+
+static void prp_put_ipu_resources(struct prp_priv *priv)
+{
+	if (!IS_ERR_OR_NULL(priv->ic))
+		ipu_ic_put(priv->ic);
+	priv->ic = NULL;
+
+	if (!IS_ERR_OR_NULL(priv->out_ch))
+		ipu_idmac_put(priv->out_ch);
+	priv->out_ch = NULL;
+
+	if (!IS_ERR_OR_NULL(priv->rot_in_ch))
+		ipu_idmac_put(priv->rot_in_ch);
+	priv->rot_in_ch = NULL;
+
+	if (!IS_ERR_OR_NULL(priv->rot_out_ch))
+		ipu_idmac_put(priv->rot_out_ch);
+	priv->rot_out_ch = NULL;
+}
+
+static int prp_get_ipu_resources(struct prp_priv *priv)
+{
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+	int ret, task = ic_priv->task_id;
+
+	priv->ipu = priv->md->ipu[ic_priv->ipu_id];
+
+	priv->ic = ipu_ic_get(priv->ipu, task);
+	if (IS_ERR(priv->ic)) {
+		v4l2_err(&ic_priv->sd, "failed to get IC\n");
+		ret = PTR_ERR(priv->ic);
+		goto out;
+	}
+
+	priv->out_ch = ipu_idmac_get(priv->ipu,
+				     prp_channel[task].out_ch);
+	if (IS_ERR(priv->out_ch)) {
+		v4l2_err(&ic_priv->sd, "could not get IDMAC channel %u\n",
+			 prp_channel[task].out_ch);
+		ret = PTR_ERR(priv->out_ch);
+		goto out;
+	}
+
+	priv->rot_in_ch = ipu_idmac_get(priv->ipu,
+					prp_channel[task].rot_in_ch);
+	if (IS_ERR(priv->rot_in_ch)) {
+		v4l2_err(&ic_priv->sd, "could not get IDMAC channel %u\n",
+			 prp_channel[task].rot_in_ch);
+		ret = PTR_ERR(priv->rot_in_ch);
+		goto out;
+	}
+
+	priv->rot_out_ch = ipu_idmac_get(priv->ipu,
+					 prp_channel[task].rot_out_ch);
+	if (IS_ERR(priv->rot_out_ch)) {
+		v4l2_err(&ic_priv->sd, "could not get IDMAC channel %u\n",
+			 prp_channel[task].rot_out_ch);
+		ret = PTR_ERR(priv->rot_out_ch);
+		goto out;
+	}
+
+	return 0;
+out:
+	prp_put_ipu_resources(priv);
+	return ret;
+}
+
+static void prp_vb2_buf_done(struct prp_priv *priv, struct ipuv3_channel *ch)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct imx_media_buffer *done, *next;
+	struct vb2_buffer *vb;
+	dma_addr_t phys;
+
+	done = priv->active_vb2_buf[priv->ipu_buf_num];
+	if (done) {
+		vb = &done->vbuf.vb2_buf;
+		vb->timestamp = ktime_get_ns();
+		vb2_buffer_done(vb, VB2_BUF_STATE_DONE);
+	}
+
+	/* get next queued buffer */
+	next = imx_media_capture_device_next_buf(vdev);
+	if (next) {
+		phys = vb2_dma_contig_plane_dma_addr(&next->vbuf.vb2_buf, 0);
+		priv->active_vb2_buf[priv->ipu_buf_num] = next;
+	} else {
+		phys = priv->underrun_buf.phys;
+		priv->active_vb2_buf[priv->ipu_buf_num] = NULL;
+	}
+
+	if (ipu_idmac_buffer_is_ready(ch, priv->ipu_buf_num))
+		ipu_idmac_clear_buffer(ch, priv->ipu_buf_num);
+
+	ipu_cpmem_set_buffer(ch, priv->ipu_buf_num, phys);
+}
+
+static irqreturn_t prp_eof_interrupt(int irq, void *dev_id)
+{
+	struct prp_priv *priv = dev_id;
+	struct ipuv3_channel *channel;
+
+	spin_lock(&priv->irqlock);
+
+	if (priv->last_eof) {
+		complete(&priv->last_eof_comp);
+		priv->last_eof = false;
+		goto unlock;
+	}
+
+	/*
+	 * if there is a CSI in the pipeline, inform it of this EOF
+	 * so it can monitor frame intervals.
+	 */
+	if (priv->csi_sd)
+		v4l2_subdev_call(priv->csi_sd, core,
+				 interrupt_service_routine,
+				 0, NULL);
+
+	channel = (ipu_rot_mode_is_irt(priv->rot_mode)) ?
+		priv->rot_out_ch : priv->out_ch;
+
+	prp_vb2_buf_done(priv, channel);
+
+	/* select new IPU buf */
+	ipu_idmac_select_buffer(channel, priv->ipu_buf_num);
+	/* toggle IPU double-buffer index */
+	priv->ipu_buf_num ^= 1;
+
+	/* bump the EOF timeout timer */
+	mod_timer(&priv->eof_timeout_timer,
+		  jiffies + msecs_to_jiffies(IMX_MEDIA_EOF_TIMEOUT));
+
+unlock:
+	spin_unlock(&priv->irqlock);
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t prp_nfb4eof_interrupt(int irq, void *dev_id)
+{
+	struct prp_priv *priv = dev_id;
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+	static const struct v4l2_event ev = {
+		.type = V4L2_EVENT_NEW_FRAME_BEFORE_EOF,
+	};
+
+	v4l2_err(&ic_priv->sd, "NFB4EOF\n");
+
+	v4l2_subdev_notify_event(&ic_priv->sd, &ev);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * EOF timeout timer function.
+ */
+/*
+ * EOF timeout timer function. This is an unrecoverable condition
+ * without a stream restart.
+ */
+static void prp_eof_timeout(unsigned long data)
+{
+	struct prp_priv *priv = (struct prp_priv *)data;
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+
+	v4l2_err(&ic_priv->sd, "EOF timeout\n");
+
+	/* signal a fatal error to capture device */
+	imx_media_capture_device_error(vdev);
+}
+
+static void prp_setup_vb2_buf(struct prp_priv *priv, dma_addr_t *phys)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct imx_media_buffer *buf;
+	int i;
+
+	for (i = 0; i < 2; i++) {
+		buf = imx_media_capture_device_next_buf(vdev);
+		priv->active_vb2_buf[i] = buf;
+		phys[i] = vb2_dma_contig_plane_dma_addr(&buf->vbuf.vb2_buf, 0);
+	}
+}
+
+static void prp_unsetup_vb2_buf(struct prp_priv *priv,
+				enum vb2_buffer_state return_state)
+{
+	struct imx_media_buffer *buf;
+	int i;
+
+	/* return any remaining active frames with error */
+	for (i = 0; i < 2; i++) {
+		buf = priv->active_vb2_buf[i];
+		if (buf) {
+			struct vb2_buffer *vb = &buf->vbuf.vb2_buf;
+
+			vb->timestamp = ktime_get_ns();
+			vb2_buffer_done(vb, return_state);
+		}
+	}
+}
+
+static int prp_setup_channel(struct prp_priv *priv,
+			     struct ipuv3_channel *channel,
+			     enum ipu_rotate_mode rot_mode,
+			     dma_addr_t addr0, dma_addr_t addr1,
+			     bool rot_swap_width_height)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	const struct imx_media_pixfmt *outcc;
+	struct v4l2_mbus_framefmt *infmt;
+	unsigned int burst_size;
+	struct ipu_image image;
+	int ret;
+
+	infmt = &priv->format_mbus[PRPENCVF_SINK_PAD];
+	outcc = vdev->cc;
+
+	ipu_cpmem_zero(channel);
+
+	memset(&image, 0, sizeof(image));
+	image.pix = vdev->fmt.fmt.pix;
+	image.rect.width = image.pix.width;
+	image.rect.height = image.pix.height;
+
+	if (rot_swap_width_height) {
+		swap(image.pix.width, image.pix.height);
+		swap(image.rect.width, image.rect.height);
+		/* recalc stride using swapped width */
+		image.pix.bytesperline = outcc->planar ?
+			image.pix.width :
+			(image.pix.width * outcc->bpp) >> 3;
+	}
+
+	image.phys0 = addr0;
+	image.phys1 = addr1;
+
+	ret = ipu_cpmem_set_image(channel, &image);
+	if (ret)
+		return ret;
+
+	if (channel == priv->rot_in_ch ||
+	    channel == priv->rot_out_ch) {
+		burst_size = 8;
+		ipu_cpmem_set_block_mode(channel);
+	} else {
+		burst_size = (image.pix.width & 0xf) ? 8 : 16;
+	}
+
+	ipu_cpmem_set_burstsize(channel, burst_size);
+
+	if (rot_mode)
+		ipu_cpmem_set_rotation(channel, rot_mode);
+
+	if (image.pix.field == V4L2_FIELD_NONE &&
+	    V4L2_FIELD_HAS_BOTH(infmt->field) &&
+	    channel == priv->out_ch)
+		ipu_cpmem_interlaced_scan(channel, image.pix.bytesperline);
+
+	ret = ipu_ic_task_idma_init(priv->ic, channel,
+				    image.pix.width, image.pix.height,
+				    burst_size, rot_mode);
+	if (ret)
+		return ret;
+
+	ipu_cpmem_set_axi_id(channel, 1);
+
+	ipu_idmac_set_double_buffer(channel, true);
+
+	return 0;
+}
+
+static int prp_setup_rotation(struct prp_priv *priv)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+	const struct imx_media_pixfmt *outcc, *incc;
+	struct v4l2_mbus_framefmt *infmt;
+	struct v4l2_pix_format *outfmt;
+	dma_addr_t phys[2];
+	int ret;
+
+	infmt = &priv->format_mbus[PRPENCVF_SINK_PAD];
+	outfmt = &vdev->fmt.fmt.pix;
+	incc = priv->cc[PRPENCVF_SINK_PAD];
+	outcc = vdev->cc;
+
+	ret = imx_media_alloc_dma_buf(priv->md, &priv->rot_buf[0],
+				      outfmt->sizeimage);
+	if (ret) {
+		v4l2_err(&ic_priv->sd, "failed to alloc rot_buf[0], %d\n", ret);
+		return ret;
+	}
+	ret = imx_media_alloc_dma_buf(priv->md, &priv->rot_buf[1],
+				      outfmt->sizeimage);
+	if (ret) {
+		v4l2_err(&ic_priv->sd, "failed to alloc rot_buf[1], %d\n", ret);
+		goto free_rot0;
+	}
+
+	ret = ipu_ic_task_init(priv->ic,
+			       infmt->width, infmt->height,
+			       outfmt->height, outfmt->width,
+			       incc->cs, outcc->cs);
+	if (ret) {
+		v4l2_err(&ic_priv->sd, "ipu_ic_task_init failed, %d\n", ret);
+		goto free_rot1;
+	}
+
+	/* init the IC-PRP-->MEM IDMAC channel */
+	ret = prp_setup_channel(priv, priv->out_ch, IPU_ROTATE_NONE,
+				priv->rot_buf[0].phys, priv->rot_buf[1].phys,
+				true);
+	if (ret) {
+		v4l2_err(&ic_priv->sd,
+			 "prp_setup_channel(out_ch) failed, %d\n", ret);
+		goto free_rot1;
+	}
+
+	/* init the MEM-->IC-PRP ROT IDMAC channel */
+	ret = prp_setup_channel(priv, priv->rot_in_ch, priv->rot_mode,
+				priv->rot_buf[0].phys, priv->rot_buf[1].phys,
+				true);
+	if (ret) {
+		v4l2_err(&ic_priv->sd,
+			 "prp_setup_channel(rot_in_ch) failed, %d\n", ret);
+		goto free_rot1;
+	}
+
+	prp_setup_vb2_buf(priv, phys);
+
+	/* init the destination IC-PRP ROT-->MEM IDMAC channel */
+	ret = prp_setup_channel(priv, priv->rot_out_ch, IPU_ROTATE_NONE,
+				phys[0], phys[1],
+				false);
+	if (ret) {
+		v4l2_err(&ic_priv->sd,
+			 "prp_setup_channel(rot_out_ch) failed, %d\n", ret);
+		goto free_rot1;
+	}
+
+	/* now link IC-PRP-->MEM to MEM-->IC-PRP ROT */
+	ipu_idmac_link(priv->out_ch, priv->rot_in_ch);
+
+	/* enable the IC */
+	ipu_ic_enable(priv->ic);
+
+	/* set buffers ready */
+	ipu_idmac_select_buffer(priv->out_ch, 0);
+	ipu_idmac_select_buffer(priv->out_ch, 1);
+	ipu_idmac_select_buffer(priv->rot_out_ch, 0);
+	ipu_idmac_select_buffer(priv->rot_out_ch, 1);
+
+	/* enable the channels */
+	ipu_idmac_enable_channel(priv->out_ch);
+	ipu_idmac_enable_channel(priv->rot_in_ch);
+	ipu_idmac_enable_channel(priv->rot_out_ch);
+
+	/* and finally enable the IC PRP task */
+	ipu_ic_task_enable(priv->ic);
+
+	return 0;
+
+free_rot1:
+	imx_media_free_dma_buf(priv->md, &priv->rot_buf[1]);
+free_rot0:
+	imx_media_free_dma_buf(priv->md, &priv->rot_buf[0]);
+	return ret;
+}
+
+static void prp_unsetup_rotation(struct prp_priv *priv)
+{
+	ipu_ic_task_disable(priv->ic);
+
+	ipu_idmac_disable_channel(priv->out_ch);
+	ipu_idmac_disable_channel(priv->rot_in_ch);
+	ipu_idmac_disable_channel(priv->rot_out_ch);
+
+	ipu_idmac_unlink(priv->out_ch, priv->rot_in_ch);
+
+	ipu_ic_disable(priv->ic);
+
+	imx_media_free_dma_buf(priv->md, &priv->rot_buf[0]);
+	imx_media_free_dma_buf(priv->md, &priv->rot_buf[1]);
+}
+
+static int prp_setup_norotation(struct prp_priv *priv)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+	const struct imx_media_pixfmt *outcc, *incc;
+	struct v4l2_mbus_framefmt *infmt;
+	struct v4l2_pix_format *outfmt;
+	dma_addr_t phys[2];
+	int ret;
+
+	infmt = &priv->format_mbus[PRPENCVF_SINK_PAD];
+	outfmt = &vdev->fmt.fmt.pix;
+	incc = priv->cc[PRPENCVF_SINK_PAD];
+	outcc = vdev->cc;
+
+	ret = ipu_ic_task_init(priv->ic,
+			       infmt->width, infmt->height,
+			       outfmt->width, outfmt->height,
+			       incc->cs, outcc->cs);
+	if (ret) {
+		v4l2_err(&ic_priv->sd, "ipu_ic_task_init failed, %d\n", ret);
+		return ret;
+	}
+
+	prp_setup_vb2_buf(priv, phys);
+
+	/* init the IC PRP-->MEM IDMAC channel */
+	ret = prp_setup_channel(priv, priv->out_ch, priv->rot_mode,
+				phys[0], phys[1], false);
+	if (ret) {
+		v4l2_err(&ic_priv->sd,
+			 "prp_setup_channel(out_ch) failed, %d\n", ret);
+		return ret;
+	}
+
+	ipu_cpmem_dump(priv->out_ch);
+	ipu_ic_dump(priv->ic);
+	ipu_dump(priv->ipu);
+
+	ipu_ic_enable(priv->ic);
+
+	/* set buffers ready */
+	ipu_idmac_select_buffer(priv->out_ch, 0);
+	ipu_idmac_select_buffer(priv->out_ch, 1);
+
+	/* enable the channels */
+	ipu_idmac_enable_channel(priv->out_ch);
+
+	/* enable the IC task */
+	ipu_ic_task_enable(priv->ic);
+
+	return 0;
+}
+
+static void prp_unsetup_norotation(struct prp_priv *priv)
+{
+	ipu_ic_task_disable(priv->ic);
+	ipu_idmac_disable_channel(priv->out_ch);
+	ipu_ic_disable(priv->ic);
+}
+
+static void prp_unsetup(struct prp_priv *priv,
+			enum vb2_buffer_state state)
+{
+	if (ipu_rot_mode_is_irt(priv->rot_mode))
+		prp_unsetup_rotation(priv);
+	else
+		prp_unsetup_norotation(priv);
+
+	prp_unsetup_vb2_buf(priv, state);
+}
+
+static int prp_start(struct prp_priv *priv)
+{
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct v4l2_pix_format *outfmt;
+	int ret;
+
+	ret = prp_get_ipu_resources(priv);
+	if (ret)
+		return ret;
+
+	outfmt = &vdev->fmt.fmt.pix;
+
+	ret = imx_media_alloc_dma_buf(priv->md, &priv->underrun_buf,
+				      outfmt->sizeimage);
+	if (ret)
+		goto out_put_ipu;
+
+	priv->ipu_buf_num = 0;
+
+	/* init EOF completion waitq */
+	init_completion(&priv->last_eof_comp);
+	priv->last_eof = false;
+
+	if (ipu_rot_mode_is_irt(priv->rot_mode))
+		ret = prp_setup_rotation(priv);
+	else
+		ret = prp_setup_norotation(priv);
+	if (ret)
+		goto out_free_underrun;
+
+	priv->nfb4eof_irq = ipu_idmac_channel_irq(priv->ipu,
+						  priv->out_ch,
+						  IPU_IRQ_NFB4EOF);
+	ret = devm_request_irq(ic_priv->dev, priv->nfb4eof_irq,
+			       prp_nfb4eof_interrupt, 0,
+			       "imx-ic-prp-nfb4eof", priv);
+	if (ret) {
+		v4l2_err(&ic_priv->sd,
+			 "Error registering NFB4EOF irq: %d\n", ret);
+		goto out_unsetup;
+	}
+
+	if (ipu_rot_mode_is_irt(priv->rot_mode))
+		priv->eof_irq = ipu_idmac_channel_irq(
+			priv->ipu, priv->rot_out_ch, IPU_IRQ_EOF);
+	else
+		priv->eof_irq = ipu_idmac_channel_irq(
+			priv->ipu, priv->out_ch, IPU_IRQ_EOF);
+
+	ret = devm_request_irq(ic_priv->dev, priv->eof_irq,
+			       prp_eof_interrupt, 0,
+			       "imx-ic-prp-eof", priv);
+	if (ret) {
+		v4l2_err(&ic_priv->sd,
+			 "Error registering eof irq: %d\n", ret);
+		goto out_free_nfb4eof_irq;
+	}
+
+	/* start the EOF timeout timer */
+	mod_timer(&priv->eof_timeout_timer,
+		  jiffies + msecs_to_jiffies(IMX_MEDIA_EOF_TIMEOUT));
+
+	return 0;
+
+out_free_nfb4eof_irq:
+	devm_free_irq(ic_priv->dev, priv->nfb4eof_irq, priv);
+out_unsetup:
+	prp_unsetup(priv, VB2_BUF_STATE_QUEUED);
+out_free_underrun:
+	imx_media_free_dma_buf(priv->md, &priv->underrun_buf);
+out_put_ipu:
+	prp_put_ipu_resources(priv);
+	return ret;
+}
+
+static void prp_stop(struct prp_priv *priv)
+{
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+	unsigned long flags;
+	int ret;
+
+	/* mark next EOF interrupt as the last before stream off */
+	spin_lock_irqsave(&priv->irqlock, flags);
+	priv->last_eof = true;
+	spin_unlock_irqrestore(&priv->irqlock, flags);
+
+	/*
+	 * and then wait for interrupt handler to mark completion.
+	 */
+	ret = wait_for_completion_timeout(
+		&priv->last_eof_comp,
+		msecs_to_jiffies(IMX_MEDIA_EOF_TIMEOUT));
+	if (ret == 0)
+		v4l2_warn(&ic_priv->sd, "wait last EOF timeout\n");
+
+	devm_free_irq(ic_priv->dev, priv->eof_irq, priv);
+	devm_free_irq(ic_priv->dev, priv->nfb4eof_irq, priv);
+
+	prp_unsetup(priv, VB2_BUF_STATE_ERROR);
+
+	imx_media_free_dma_buf(priv->md, &priv->underrun_buf);
+
+	/* cancel the EOF timeout timer */
+	del_timer_sync(&priv->eof_timeout_timer);
+
+	prp_put_ipu_resources(priv);
+}
+
+static int prp_enum_mbus_code(struct v4l2_subdev *sd,
+			      struct v4l2_subdev_pad_config *cfg,
+			      struct v4l2_subdev_mbus_code_enum *code)
+{
+	if (code->pad >= PRPENCVF_NUM_PADS)
+		return -EINVAL;
+
+	if (code->pad == PRPENCVF_SRC_PAD)
+		return imx_media_enum_format(NULL, &code->code, code->index,
+					     true, false);
+
+	return imx_media_enum_ipu_format(NULL, &code->code, code->index, true);
+}
+
+static struct v4l2_mbus_framefmt *
+__prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_pad_config *cfg,
+	      unsigned int pad, enum v4l2_subdev_format_whence which)
+{
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+
+	if (which == V4L2_SUBDEV_FORMAT_TRY)
+		return v4l2_subdev_get_try_format(&ic_priv->sd, cfg, pad);
+	else
+		return &priv->format_mbus[pad];
+}
+
+/*
+ * V4L2 subdev operations.
+ */
+
+static int prp_get_fmt(struct v4l2_subdev *sd,
+		       struct v4l2_subdev_pad_config *cfg,
+		       struct v4l2_subdev_format *sdformat)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+	struct v4l2_mbus_framefmt *fmt;
+	int ret = 0;
+
+	if (sdformat->pad >= PRPENCVF_NUM_PADS)
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	fmt = __prp_get_fmt(priv, cfg, sdformat->pad, sdformat->which);
+	if (!fmt) {
+		ret = -EINVAL;
+		goto out;
+	}
+
+	sdformat->format = *fmt;
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int prp_set_fmt(struct v4l2_subdev *sd,
+		       struct v4l2_subdev_pad_config *cfg,
+		       struct v4l2_subdev_format *sdformat)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+	const struct imx_media_pixfmt *cc;
+	struct v4l2_mbus_framefmt *infmt;
+	int ret = 0;
+	u32 code;
+
+	if (sdformat->pad >= PRPENCVF_NUM_PADS)
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	if (priv->stream_on) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	if (sdformat->pad == PRPENCVF_SRC_PAD) {
+		infmt = __prp_get_fmt(priv, cfg, PRPENCVF_SINK_PAD,
+				      sdformat->which);
+
+		cc = imx_media_find_format(0, sdformat->format.code,
+					   true, false);
+		if (!cc) {
+			imx_media_enum_format(NULL, &code, 0, true, false);
+			cc = imx_media_find_format(0, code, true, false);
+			sdformat->format.code = cc->codes[0];
+		}
+
+		if (sdformat->format.field != V4L2_FIELD_NONE)
+			sdformat->format.field = infmt->field;
+
+		/* IC resizer cannot downsize more than 4:1 */
+		if (ipu_rot_mode_is_irt(priv->rot_mode))
+			v4l_bound_align_image(&sdformat->format.width,
+					      infmt->height / 4, MAX_H_SRC,
+					      H_ALIGN_SRC,
+					      &sdformat->format.height,
+					      infmt->width / 4, MAX_W_SRC,
+					      W_ALIGN_SRC, S_ALIGN);
+		else
+			v4l_bound_align_image(&sdformat->format.width,
+					      infmt->width / 4, MAX_W_SRC,
+					      W_ALIGN_SRC,
+					      &sdformat->format.height,
+					      infmt->height / 4, MAX_H_SRC,
+					      H_ALIGN_SRC, S_ALIGN);
+	} else {
+		cc = imx_media_find_ipu_format(0, sdformat->format.code,
+					       true);
+		if (!cc) {
+			imx_media_enum_ipu_format(NULL, &code, 0, true);
+			cc = imx_media_find_ipu_format(0, code, true);
+			sdformat->format.code = cc->codes[0];
+		}
+
+		v4l_bound_align_image(&sdformat->format.width,
+				      MIN_W_SINK, MAX_W_SINK, W_ALIGN_SINK,
+				      &sdformat->format.height,
+				      MIN_H_SINK, MAX_H_SINK, H_ALIGN_SINK,
+				      S_ALIGN);
+	}
+
+	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
+		cfg->try_fmt = sdformat->format;
+	} else {
+		priv->format_mbus[sdformat->pad] = sdformat->format;
+		priv->cc[sdformat->pad] = cc;
+	}
+
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int prp_g_frame_interval(struct v4l2_subdev *sd,
+				struct v4l2_subdev_frame_interval *fi)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+
+	mutex_lock(&priv->lock);
+	fi->interval = priv->frame_interval;
+	mutex_unlock(&priv->lock);
+
+	return 0;
+}
+
+static int prp_s_frame_interval(struct v4l2_subdev *sd,
+				struct v4l2_subdev_frame_interval *fi)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+
+	mutex_lock(&priv->lock);
+
+	/* Output pads mirror active input pad, no limits on input pads */
+	if (fi->pad == PRPENCVF_SRC_PAD)
+		fi->interval = priv->frame_interval;
+
+	priv->frame_interval = fi->interval;
+
+	mutex_unlock(&priv->lock);
+
+	return 0;
+}
+
+static int prp_link_setup(struct media_entity *entity,
+			  const struct media_pad *local,
+			  const struct media_pad *remote, u32 flags)
+{
+	struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity);
+	struct imx_ic_priv *ic_priv = v4l2_get_subdevdata(sd);
+	struct prp_priv *priv = ic_priv->task_priv;
+	struct v4l2_subdev *remote_sd;
+	int ret = 0;
+
+	dev_dbg(ic_priv->dev, "link setup %s -> %s", remote->entity->name,
+		local->entity->name);
+
+	mutex_lock(&priv->lock);
+
+	if (local->flags & MEDIA_PAD_FL_SINK) {
+		if (!is_media_entity_v4l2_subdev(remote->entity)) {
+			ret = -EINVAL;
+			goto out;
+		}
+
+		remote_sd = media_entity_to_v4l2_subdev(remote->entity);
+
+		if (flags & MEDIA_LNK_FL_ENABLED) {
+			if (priv->src_sd) {
+				ret = -EBUSY;
+				goto out;
+			}
+			priv->src_sd = remote_sd;
+		} else {
+			priv->src_sd = NULL;
+		}
+
+		goto out;
+	}
+
+	/* this is the source pad */
+
+	/* the remote must be the device node */
+	if (!is_media_entity_v4l2_video_device(remote->entity)) {
+		ret = -EINVAL;
+		goto out;
+	}
+
+	if (flags & MEDIA_LNK_FL_ENABLED) {
+		if (priv->sink) {
+			ret = -EBUSY;
+			goto out;
+		}
+	} else {
+		priv->sink = NULL;
+		goto out;
+	}
+
+	priv->sink = remote->entity;
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int prp_link_validate(struct v4l2_subdev *sd,
+			     struct media_link *link,
+			     struct v4l2_subdev_format *source_fmt,
+			     struct v4l2_subdev_format *sink_fmt)
+{
+	struct imx_ic_priv *ic_priv = v4l2_get_subdevdata(sd);
+	struct prp_priv *priv = ic_priv->task_priv;
+	struct imx_media_subdev *csi;
+	int ret;
+
+	ret = v4l2_subdev_link_validate_default(sd, link,
+						source_fmt, sink_fmt);
+	if (ret)
+		return ret;
+
+	ret = v4l2_subdev_link_validate_frame_interval(link);
+	if (ret)
+		return ret;
+
+	csi = imx_media_find_pipeline_subdev(priv->md, &ic_priv->sd.entity,
+					     IMX_MEDIA_GRP_ID_CSI);
+	if (IS_ERR(csi))
+		csi = NULL;
+
+	mutex_lock(&priv->lock);
+	priv->csi_sd = csi ? csi->sd : NULL;
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int prp_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct prp_priv *priv = container_of(ctrl->handler,
+					       struct prp_priv, ctrl_hdlr);
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+	enum ipu_rotate_mode rot_mode;
+	int rotation, ret = 0;
+	bool hflip, vflip;
+
+	mutex_lock(&priv->lock);
+
+	rotation = priv->rotation;
+	hflip = priv->hflip;
+	vflip = priv->vflip;
+
+	switch (ctrl->id) {
+	case V4L2_CID_HFLIP:
+		hflip = (ctrl->val == 1);
+		break;
+	case V4L2_CID_VFLIP:
+		vflip = (ctrl->val == 1);
+		break;
+	case V4L2_CID_ROTATE:
+		rotation = ctrl->val;
+		break;
+	default:
+		v4l2_err(&ic_priv->sd, "Invalid control\n");
+		ret = -EINVAL;
+		goto out;
+	}
+
+	ret = ipu_degrees_to_rot_mode(&rot_mode, rotation, hflip, vflip);
+	if (ret)
+		goto out;
+
+	if (rot_mode != priv->rot_mode) {
+		/* can't change rotation mid-streaming */
+		if (priv->stream_on) {
+			ret = -EBUSY;
+			goto out;
+		}
+		priv->rot_mode = rot_mode;
+		priv->rotation = rotation;
+		priv->hflip = hflip;
+		priv->vflip = vflip;
+	}
+
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static const struct v4l2_ctrl_ops prp_ctrl_ops = {
+	.s_ctrl = prp_s_ctrl,
+};
+
+static int prp_init_controls(struct prp_priv *priv)
+{
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+	struct v4l2_ctrl_handler *hdlr = &priv->ctrl_hdlr;
+	int ret;
+
+	v4l2_ctrl_handler_init(hdlr, 3);
+
+	v4l2_ctrl_new_std(hdlr, &prp_ctrl_ops, V4L2_CID_HFLIP,
+			  0, 1, 1, 0);
+	v4l2_ctrl_new_std(hdlr, &prp_ctrl_ops, V4L2_CID_VFLIP,
+			  0, 1, 1, 0);
+	v4l2_ctrl_new_std(hdlr, &prp_ctrl_ops, V4L2_CID_ROTATE,
+			  0, 270, 90, 0);
+
+	ic_priv->sd.ctrl_handler = hdlr;
+
+	if (hdlr->error) {
+		ret = hdlr->error;
+		goto out_free;
+	}
+
+	v4l2_ctrl_handler_setup(hdlr);
+	return 0;
+
+out_free:
+	v4l2_ctrl_handler_free(hdlr);
+	return ret;
+}
+
+static int prp_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct imx_ic_priv *ic_priv = v4l2_get_subdevdata(sd);
+	struct prp_priv *priv = ic_priv->task_priv;
+	int ret = 0;
+
+	mutex_lock(&priv->lock);
+
+	if (!priv->src_sd || !priv->sink) {
+		ret = -EPIPE;
+		goto out;
+	}
+
+	dev_dbg(ic_priv->dev, "stream %s\n", enable ? "ON" : "OFF");
+
+	if (enable && !priv->stream_on)
+		ret = prp_start(priv);
+	else if (!enable && priv->stream_on)
+		prp_stop(priv);
+
+	if (!ret)
+		priv->stream_on = enable;
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int prp_subscribe_event(struct v4l2_subdev *sd, struct v4l2_fh *fh,
+			       struct v4l2_event_subscription *sub)
+{
+	if (sub->type != V4L2_EVENT_NEW_FRAME_BEFORE_EOF)
+		return -EINVAL;
+	if (sub->id != 0)
+		return -EINVAL;
+
+	return v4l2_event_subscribe(fh, sub, 0, NULL);
+}
+
+static int prp_unsubscribe_event(struct v4l2_subdev *sd, struct v4l2_fh *fh,
+				 struct v4l2_event_subscription *sub)
+{
+	return v4l2_event_unsubscribe(fh, sub);
+}
+
+/*
+ * retrieve our pads parsed from the OF graph by the media device
+ */
+static int prp_registered(struct v4l2_subdev *sd)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+	int i, ret;
+	u32 code;
+
+	/* get media device */
+	priv->md = dev_get_drvdata(sd->v4l2_dev->dev);
+
+	for (i = 0; i < PRPENCVF_NUM_PADS; i++) {
+		if (i == PRPENCVF_SINK_PAD) {
+			priv->pad[i].flags = MEDIA_PAD_FL_SINK;
+			imx_media_enum_ipu_format(NULL, &code, 0, true);
+		} else {
+			priv->pad[i].flags = MEDIA_PAD_FL_SOURCE;
+			code = 0;
+		}
+
+		/* set a default mbus format  */
+		ret = imx_media_init_mbus_fmt(&priv->format_mbus[i],
+					      640, 480, code, V4L2_FIELD_NONE,
+					      &priv->cc[i]);
+		if (ret)
+			return ret;
+	}
+
+	/* init default frame interval */
+	priv->frame_interval.numerator = 1;
+	priv->frame_interval.denominator = 30;
+
+	ret = media_entity_pads_init(&sd->entity, PRPENCVF_NUM_PADS,
+				     priv->pad);
+	if (ret)
+		return ret;
+
+	ret = imx_media_capture_device_register(priv->vdev);
+	if (ret)
+		return ret;
+
+	ret = prp_init_controls(priv);
+	if (ret)
+		imx_media_capture_device_unregister(priv->vdev);
+
+	return ret;
+}
+
+static void prp_unregistered(struct v4l2_subdev *sd)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+
+	imx_media_capture_device_unregister(priv->vdev);
+	v4l2_ctrl_handler_free(&priv->ctrl_hdlr);
+}
+
+static struct v4l2_subdev_pad_ops prp_pad_ops = {
+	.enum_mbus_code = prp_enum_mbus_code,
+	.get_fmt = prp_get_fmt,
+	.set_fmt = prp_set_fmt,
+	.link_validate = prp_link_validate,
+};
+
+static const struct v4l2_subdev_core_ops prp_core_ops = {
+	.subscribe_event = prp_subscribe_event,
+	.unsubscribe_event = prp_unsubscribe_event,
+};
+
+static struct v4l2_subdev_video_ops prp_video_ops = {
+	.s_stream = prp_s_stream,
+	.g_frame_interval = prp_g_frame_interval,
+	.s_frame_interval = prp_s_frame_interval,
+};
+
+static struct media_entity_operations prp_entity_ops = {
+	.link_setup = prp_link_setup,
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static struct v4l2_subdev_ops prp_subdev_ops = {
+	.core = &prp_core_ops,
+	.video = &prp_video_ops,
+	.pad = &prp_pad_ops,
+};
+
+static struct v4l2_subdev_internal_ops prp_internal_ops = {
+	.registered = prp_registered,
+	.unregistered = prp_unregistered,
+};
+
+static int prp_init(struct imx_ic_priv *ic_priv)
+{
+	struct prp_priv *priv;
+
+	priv = devm_kzalloc(ic_priv->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	ic_priv->task_priv = priv;
+	priv->ic_priv = ic_priv;
+
+	spin_lock_init(&priv->irqlock);
+	init_timer(&priv->eof_timeout_timer);
+	priv->eof_timeout_timer.data = (unsigned long)priv;
+	priv->eof_timeout_timer.function = prp_eof_timeout;
+
+	priv->vdev = imx_media_capture_device_init(&ic_priv->sd,
+						   PRPENCVF_SRC_PAD);
+	if (IS_ERR(priv->vdev))
+		return PTR_ERR(priv->vdev);
+
+	mutex_init(&priv->lock);
+
+	return 0;
+}
+
+static void prp_remove(struct imx_ic_priv *ic_priv)
+{
+	struct prp_priv *priv = ic_priv->task_priv;
+
+	mutex_destroy(&priv->lock);
+	imx_media_capture_device_remove(priv->vdev);
+}
+
+struct imx_ic_ops imx_ic_prpencvf_ops = {
+	.subdev_ops = &prp_subdev_ops,
+	.internal_ops = &prp_internal_ops,
+	.entity_ops = &prp_entity_ops,
+	.init = prp_init,
+	.remove = prp_remove,
+};
diff --git a/drivers/staging/media/imx/imx-ic.h b/drivers/staging/media/imx/imx-ic.h
new file mode 100644
index 0000000..5535111
--- /dev/null
+++ b/drivers/staging/media/imx/imx-ic.h
@@ -0,0 +1,38 @@
+/*
+ * V4L2 Image Converter Subdev for Freescale i.MX5/6 SOC
+ *
+ * Copyright (c) 2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#ifndef _IMX_IC_H
+#define _IMX_IC_H
+
+#include <media/v4l2-subdev.h>
+
+struct imx_ic_priv {
+	struct device *dev;
+	struct v4l2_subdev sd;
+	int    ipu_id;
+	int    task_id;
+	void   *prp_priv;
+	void   *task_priv;
+};
+
+struct imx_ic_ops {
+	struct v4l2_subdev_ops *subdev_ops;
+	struct v4l2_subdev_internal_ops *internal_ops;
+	struct media_entity_operations *entity_ops;
+
+	int (*init)(struct imx_ic_priv *ic_priv);
+	void (*remove)(struct imx_ic_priv *ic_priv);
+};
+
+extern struct imx_ic_ops imx_ic_prp_ops;
+extern struct imx_ic_ops imx_ic_prpencvf_ops;
+extern struct imx_ic_ops imx_ic_pp_ops;
+
+#endif
-- 
2.7.4

[PATCH v5 27/39] media: imx: Add IC subdev drivers

[Steve Longerbeam]

This is a set of three media entity subdevice drivers for the i.MX
Image Converter:

- Pre-process Router: Takes input frames from CSI0, CSI1, or VDIC.
  Two output pads enable either or both of the preprocess tasks
  below. If the input is from one of the CSIs, both proprocess task
  links can be enabled to process frames from that CSI simultaneously.
  If the input is the VDIC, only the Pre-processing Viewfinder task
  link can be enabled.

- Pre-processing Encode task: video frames are routed directly from
  the CSI and can be scaled, color-space converted, and rotated.
  Scaled output is limited to 1024x1024 resolution. Output frames
  are routed to the capture device.

- Pre-processing Viewfinder task: this task can perform the same
  conversions as the pre-process encode task, but in addition can
  be used for hardware motion compensated deinterlacing. Frames can
  come either directly from the CSI or from the VDIC. Scaled output
  is limited to 1024x1024 resolution. Output frames are routed to
  the capture device.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/Makefile          |    2 +
 drivers/staging/media/imx/imx-ic-common.c   |  113 +++
 drivers/staging/media/imx/imx-ic-prp.c      |  475 +++++++++++
 drivers/staging/media/imx/imx-ic-prpencvf.c | 1219 +++++++++++++++++++++++++++
 drivers/staging/media/imx/imx-ic.h          |   38 +
 5 files changed, 1847 insertions(+)
 create mode 100644 drivers/staging/media/imx/imx-ic-common.c
 create mode 100644 drivers/staging/media/imx/imx-ic-prp.c
 create mode 100644 drivers/staging/media/imx/imx-ic-prpencvf.c
 create mode 100644 drivers/staging/media/imx/imx-ic.h

diff --git a/drivers/staging/media/imx/Makefile b/drivers/staging/media/imx/Makefile
index 1f01520..878a126 100644
--- a/drivers/staging/media/imx/Makefile
+++ b/drivers/staging/media/imx/Makefile
@@ -1,9 +1,11 @@
 imx-media-objs := imx-media-dev.o imx-media-internal-sd.o imx-media-of.o
 imx-media-common-objs := imx-media-utils.o imx-media-fim.o
+imx-media-ic-objs := imx-ic-common.o imx-ic-prp.o imx-ic-prpencvf.o
 
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-common.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-capture.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-vdic.o
+obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-ic.o
 
 obj-$(CONFIG_VIDEO_IMX_CSI) += imx-media-csi.o
diff --git a/drivers/staging/media/imx/imx-ic-common.c b/drivers/staging/media/imx/imx-ic-common.c
new file mode 100644
index 0000000..cfdd490
--- /dev/null
+++ b/drivers/staging/media/imx/imx-ic-common.c
@@ -0,0 +1,113 @@
+/*
+ * V4L2 Image Converter Subdev for Freescale i.MX5/6 SOC
+ *
+ * Copyright (c) 2014-2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-subdev.h>
+#include "imx-media.h"
+#include "imx-ic.h"
+
+#define IC_TASK_PRP IC_NUM_TASKS
+#define IC_NUM_OPS  (IC_NUM_TASKS + 1)
+
+static struct imx_ic_ops *ic_ops[IC_NUM_OPS] = {
+	[IC_TASK_PRP]            = &imx_ic_prp_ops,
+	[IC_TASK_ENCODER]        = &imx_ic_prpencvf_ops,
+	[IC_TASK_VIEWFINDER]     = &imx_ic_prpencvf_ops,
+};
+
+static int imx_ic_probe(struct platform_device *pdev)
+{
+	struct imx_media_internal_sd_platformdata *pdata;
+	struct imx_ic_priv *priv;
+	int ret;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, &priv->sd);
+	priv->dev = &pdev->dev;
+
+	/* get our ipu_id, grp_id and IC task id */
+	pdata = priv->dev->platform_data;
+	priv->ipu_id = pdata->ipu_id;
+	switch (pdata->grp_id) {
+	case IMX_MEDIA_GRP_ID_IC_PRP:
+		priv->task_id = IC_TASK_PRP;
+		break;
+	case IMX_MEDIA_GRP_ID_IC_PRPENC:
+		priv->task_id = IC_TASK_ENCODER;
+		break;
+	case IMX_MEDIA_GRP_ID_IC_PRPVF:
+		priv->task_id = IC_TASK_VIEWFINDER;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	v4l2_subdev_init(&priv->sd, ic_ops[priv->task_id]->subdev_ops);
+	v4l2_set_subdevdata(&priv->sd, priv);
+	priv->sd.internal_ops = ic_ops[priv->task_id]->internal_ops;
+	priv->sd.entity.ops = ic_ops[priv->task_id]->entity_ops;
+	priv->sd.entity.function = MEDIA_ENT_F_PROC_VIDEO_SCALER;
+	priv->sd.dev = &pdev->dev;
+	priv->sd.owner = THIS_MODULE;
+	priv->sd.flags = V4L2_SUBDEV_FL_HAS_DEVNODE | V4L2_SUBDEV_FL_HAS_EVENTS;
+	priv->sd.grp_id = pdata->grp_id;
+	strncpy(priv->sd.name, pdata->sd_name, sizeof(priv->sd.name));
+
+	ret = ic_ops[priv->task_id]->init(priv);
+	if (ret)
+		return ret;
+
+	ret = v4l2_async_register_subdev(&priv->sd);
+	if (ret)
+		ic_ops[priv->task_id]->remove(priv);
+
+	return ret;
+}
+
+static int imx_ic_remove(struct platform_device *pdev)
+{
+	struct v4l2_subdev *sd = platform_get_drvdata(pdev);
+	struct imx_ic_priv *priv = container_of(sd, struct imx_ic_priv, sd);
+
+	v4l2_info(sd, "Removing\n");
+
+	ic_ops[priv->task_id]->remove(priv);
+
+	v4l2_async_unregister_subdev(sd);
+	media_entity_cleanup(&sd->entity);
+
+	return 0;
+}
+
+static const struct platform_device_id imx_ic_ids[] = {
+	{ .name = "imx-ipuv3-ic" },
+	{ },
+};
+MODULE_DEVICE_TABLE(platform, imx_ic_ids);
+
+static struct platform_driver imx_ic_driver = {
+	.probe = imx_ic_probe,
+	.remove = imx_ic_remove,
+	.id_table = imx_ic_ids,
+	.driver = {
+		.name = "imx-ipuv3-ic",
+	},
+};
+module_platform_driver(imx_ic_driver);
+
+MODULE_DESCRIPTION("i.MX IC subdev driver");
+MODULE_AUTHOR("Steve Longerbeam <steve_longerbeam@mentor.com>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:imx-ipuv3-ic");
diff --git a/drivers/staging/media/imx/imx-ic-prp.c b/drivers/staging/media/imx/imx-ic-prp.c
new file mode 100644
index 0000000..1832915
--- /dev/null
+++ b/drivers/staging/media/imx/imx-ic-prp.c
@@ -0,0 +1,475 @@
+/*
+ * V4L2 Capture IC Preprocess Subdev for Freescale i.MX5/6 SOC
+ *
+ * This subdevice handles capture of video frames from the CSI or VDIC,
+ * which are routed directly to the Image Converter preprocess tasks,
+ * for resizing, colorspace conversion, and rotation.
+ *
+ * Copyright (c) 2012-2017 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/timer.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-ioctl.h>
+#include <media/v4l2-subdev.h>
+#include <media/imx.h>
+#include "imx-media.h"
+#include "imx-ic.h"
+
+/*
+ * Min/Max supported width and heights.
+ */
+#define MIN_W       176
+#define MIN_H       144
+#define MAX_W      4096
+#define MAX_H      4096
+#define W_ALIGN    4 /* multiple of 16 pixels */
+#define H_ALIGN    1 /* multiple of 2 lines */
+#define S_ALIGN    1 /* multiple of 2 */
+
+struct prp_priv {
+	struct imx_media_dev *md;
+	struct imx_ic_priv *ic_priv;
+	struct media_pad pad[PRP_NUM_PADS];
+
+	/* lock to protect all members below */
+	struct mutex lock;
+
+	/* IPU units we require */
+	struct ipu_soc *ipu;
+
+	struct v4l2_subdev *src_sd;
+	struct v4l2_subdev *sink_sd_prpenc;
+	struct v4l2_subdev *sink_sd_prpvf;
+
+	/* the CSI id at link validate */
+	int csi_id;
+
+	struct v4l2_mbus_framefmt format_mbus[PRP_NUM_PADS];
+	const struct imx_media_pixfmt *cc[PRP_NUM_PADS];
+	struct v4l2_fract frame_interval;
+
+	bool stream_on; /* streaming is on */
+};
+
+static inline struct prp_priv *sd_to_priv(struct v4l2_subdev *sd)
+{
+	struct imx_ic_priv *ic_priv = v4l2_get_subdevdata(sd);
+
+	return ic_priv->prp_priv;
+}
+
+static int prp_start(struct prp_priv *priv)
+{
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+
+	priv->ipu = priv->md->ipu[ic_priv->ipu_id];
+
+	/* set IC to receive from CSI or VDI depending on source */
+	if (priv->src_sd->grp_id & IMX_MEDIA_GRP_ID_VDIC)
+		ipu_set_ic_src_mux(priv->ipu, 0, true);
+	else
+		ipu_set_ic_src_mux(priv->ipu, priv->csi_id, false);
+
+	return 0;
+}
+
+static void prp_stop(struct prp_priv *priv)
+{
+}
+
+static int prp_enum_mbus_code(struct v4l2_subdev *sd,
+			      struct v4l2_subdev_pad_config *cfg,
+			      struct v4l2_subdev_mbus_code_enum *code)
+{
+	if (code->pad >= PRP_NUM_PADS)
+		return -EINVAL;
+
+	return imx_media_enum_ipu_format(NULL, &code->code, code->index, true);
+}
+
+static struct v4l2_mbus_framefmt *
+__prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_pad_config *cfg,
+	      unsigned int pad, enum v4l2_subdev_format_whence which)
+{
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+
+	if (which == V4L2_SUBDEV_FORMAT_TRY)
+		return v4l2_subdev_get_try_format(&ic_priv->sd, cfg, pad);
+	else
+		return &priv->format_mbus[pad];
+}
+
+/*
+ * V4L2 subdev operations.
+ */
+
+static int prp_get_fmt(struct v4l2_subdev *sd,
+		       struct v4l2_subdev_pad_config *cfg,
+		       struct v4l2_subdev_format *sdformat)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+	struct v4l2_mbus_framefmt *fmt;
+	int ret = 0;
+
+	if (sdformat->pad >= PRP_NUM_PADS)
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	fmt = __prp_get_fmt(priv, cfg, sdformat->pad, sdformat->which);
+	if (!fmt) {
+		ret = -EINVAL;
+		goto out;
+	}
+
+	sdformat->format = *fmt;
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int prp_set_fmt(struct v4l2_subdev *sd,
+		       struct v4l2_subdev_pad_config *cfg,
+		       struct v4l2_subdev_format *sdformat)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+	const struct imx_media_pixfmt *cc = NULL;
+	struct v4l2_mbus_framefmt *infmt;
+	int ret = 0;
+	u32 code;
+
+	if (sdformat->pad >= PRP_NUM_PADS)
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	if (priv->stream_on) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	cc = imx_media_find_ipu_format(0, sdformat->format.code, true);
+	if (!cc) {
+		imx_media_enum_ipu_format(NULL, &code, 0, true);
+		cc = imx_media_find_ipu_format(0, code, true);
+		sdformat->format.code = cc->codes[0];
+	}
+
+	v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
+			      W_ALIGN, &sdformat->format.height,
+			      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
+
+	/* Output pads mirror input pad */
+	if (sdformat->pad == PRP_SRC_PAD_PRPENC ||
+	    sdformat->pad == PRP_SRC_PAD_PRPVF) {
+		infmt = __prp_get_fmt(priv, cfg, PRP_SINK_PAD,
+				      sdformat->which);
+		sdformat->format = *infmt;
+	}
+
+	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
+		cfg->try_fmt = sdformat->format;
+	} else {
+		priv->format_mbus[sdformat->pad] = sdformat->format;
+		priv->cc[sdformat->pad] = cc;
+	}
+
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int prp_g_frame_interval(struct v4l2_subdev *sd,
+				struct v4l2_subdev_frame_interval *fi)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+
+	mutex_lock(&priv->lock);
+	fi->interval = priv->frame_interval;
+	mutex_unlock(&priv->lock);
+
+	return 0;
+}
+
+static int prp_s_frame_interval(struct v4l2_subdev *sd,
+				struct v4l2_subdev_frame_interval *fi)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+
+	mutex_lock(&priv->lock);
+
+	/* Output pads mirror active input pad, no limits on input pads */
+	if (fi->pad != PRP_SINK_PAD)
+		fi->interval = priv->frame_interval;
+
+	priv->frame_interval = fi->interval;
+
+	mutex_unlock(&priv->lock);
+
+	return 0;
+}
+
+static int prp_link_setup(struct media_entity *entity,
+			  const struct media_pad *local,
+			  const struct media_pad *remote, u32 flags)
+{
+	struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity);
+	struct imx_ic_priv *ic_priv = v4l2_get_subdevdata(sd);
+	struct prp_priv *priv = ic_priv->prp_priv;
+	struct v4l2_subdev *remote_sd;
+	int ret = 0;
+
+	dev_dbg(ic_priv->dev, "link setup %s -> %s", remote->entity->name,
+		local->entity->name);
+
+	remote_sd = media_entity_to_v4l2_subdev(remote->entity);
+
+	mutex_lock(&priv->lock);
+
+	if (local->flags & MEDIA_PAD_FL_SINK) {
+		if (flags & MEDIA_LNK_FL_ENABLED) {
+			if (priv->src_sd) {
+				ret = -EBUSY;
+				goto out;
+			}
+			if (priv->sink_sd_prpenc && (remote_sd->grp_id &
+						     IMX_MEDIA_GRP_ID_VDIC)) {
+				ret = -EINVAL;
+				goto out;
+			}
+			priv->src_sd = remote_sd;
+		} else {
+			priv->src_sd = NULL;
+		}
+
+		goto out;
+	}
+
+	/* this is a source pad */
+	if (flags & MEDIA_LNK_FL_ENABLED) {
+		switch (local->index) {
+		case PRP_SRC_PAD_PRPENC:
+			if (priv->sink_sd_prpenc) {
+				ret = -EBUSY;
+				goto out;
+			}
+			if (priv->src_sd && (priv->src_sd->grp_id &
+					     IMX_MEDIA_GRP_ID_VDIC)) {
+				ret = -EINVAL;
+				goto out;
+			}
+			priv->sink_sd_prpenc = remote_sd;
+			break;
+		case PRP_SRC_PAD_PRPVF:
+			if (priv->sink_sd_prpvf) {
+				ret = -EBUSY;
+				goto out;
+			}
+			priv->sink_sd_prpvf = remote_sd;
+			break;
+		default:
+			ret = -EINVAL;
+		}
+	} else {
+		switch (local->index) {
+		case PRP_SRC_PAD_PRPENC:
+			priv->sink_sd_prpenc = NULL;
+			break;
+		case PRP_SRC_PAD_PRPVF:
+			priv->sink_sd_prpvf = NULL;
+			break;
+		default:
+			ret = -EINVAL;
+		}
+	}
+
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int prp_link_validate(struct v4l2_subdev *sd,
+			     struct media_link *link,
+			     struct v4l2_subdev_format *source_fmt,
+			     struct v4l2_subdev_format *sink_fmt)
+{
+	struct imx_ic_priv *ic_priv = v4l2_get_subdevdata(sd);
+	struct prp_priv *priv = ic_priv->prp_priv;
+	struct imx_media_subdev *csi;
+	int ret;
+
+	ret = v4l2_subdev_link_validate_default(sd, link,
+						source_fmt, sink_fmt);
+	if (ret)
+		return ret;
+
+	ret = v4l2_subdev_link_validate_frame_interval(link);
+	if (ret)
+		return ret;
+
+	csi = imx_media_find_pipeline_subdev(priv->md, &ic_priv->sd.entity,
+					     IMX_MEDIA_GRP_ID_CSI);
+	if (IS_ERR(csi))
+		csi = NULL;
+
+	mutex_lock(&priv->lock);
+
+	if (priv->src_sd->grp_id & IMX_MEDIA_GRP_ID_VDIC) {
+		/*
+		 * the ->PRPENC link cannot be enabled if the source
+		 * is the VDIC
+		 */
+		if (priv->sink_sd_prpenc)
+			ret = -EINVAL;
+		goto out;
+	} else {
+		/* the source is a CSI */
+		if (!csi) {
+			ret = -EINVAL;
+			goto out;
+		}
+
+		switch (csi->sd->grp_id) {
+		case IMX_MEDIA_GRP_ID_CSI0:
+			priv->csi_id = 0;
+			break;
+		case IMX_MEDIA_GRP_ID_CSI1:
+			priv->csi_id = 1;
+			break;
+		default:
+			ret = -EINVAL;
+		}
+	}
+
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int prp_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct imx_ic_priv *ic_priv = v4l2_get_subdevdata(sd);
+	struct prp_priv *priv = ic_priv->prp_priv;
+	int ret = 0;
+
+	mutex_lock(&priv->lock);
+
+	if (!priv->src_sd || (!priv->sink_sd_prpenc && !priv->sink_sd_prpvf)) {
+		ret = -EPIPE;
+		goto out;
+	}
+
+	dev_dbg(ic_priv->dev, "stream %s\n", enable ? "ON" : "OFF");
+
+	if (enable && !priv->stream_on)
+		ret = prp_start(priv);
+	else if (!enable && priv->stream_on)
+		prp_stop(priv);
+
+	if (!ret)
+		priv->stream_on = enable;
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+/*
+ * retrieve our pads parsed from the OF graph by the media device
+ */
+static int prp_registered(struct v4l2_subdev *sd)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+	int i, ret;
+	u32 code;
+
+	/* get media device */
+	priv->md = dev_get_drvdata(sd->v4l2_dev->dev);
+
+	for (i = 0; i < PRP_NUM_PADS; i++) {
+		priv->pad[i].flags = (i == PRP_SINK_PAD) ?
+			MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
+
+		/* set a default mbus format  */
+		imx_media_enum_ipu_format(NULL, &code, 0, true);
+		ret = imx_media_init_mbus_fmt(&priv->format_mbus[i],
+					      640, 480, code, V4L2_FIELD_NONE,
+					      &priv->cc[i]);
+		if (ret)
+			return ret;
+	}
+
+	/* init default frame interval */
+	priv->frame_interval.numerator = 1;
+	priv->frame_interval.denominator = 30;
+
+	return media_entity_pads_init(&sd->entity, PRP_NUM_PADS, priv->pad);
+}
+
+static struct v4l2_subdev_pad_ops prp_pad_ops = {
+	.enum_mbus_code = prp_enum_mbus_code,
+	.get_fmt = prp_get_fmt,
+	.set_fmt = prp_set_fmt,
+	.link_validate = prp_link_validate,
+};
+
+static struct v4l2_subdev_video_ops prp_video_ops = {
+	.s_stream = prp_s_stream,
+	.g_frame_interval = prp_g_frame_interval,
+	.s_frame_interval = prp_s_frame_interval,
+};
+
+static struct media_entity_operations prp_entity_ops = {
+	.link_setup = prp_link_setup,
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static struct v4l2_subdev_ops prp_subdev_ops = {
+	.video = &prp_video_ops,
+	.pad = &prp_pad_ops,
+};
+
+static struct v4l2_subdev_internal_ops prp_internal_ops = {
+	.registered = prp_registered,
+};
+
+static int prp_init(struct imx_ic_priv *ic_priv)
+{
+	struct prp_priv *priv;
+
+	priv = devm_kzalloc(ic_priv->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	mutex_init(&priv->lock);
+	ic_priv->prp_priv = priv;
+	priv->ic_priv = ic_priv;
+
+	return 0;
+}
+
+static void prp_remove(struct imx_ic_priv *ic_priv)
+{
+	struct prp_priv *priv = ic_priv->prp_priv;
+
+	mutex_destroy(&priv->lock);
+}
+
+struct imx_ic_ops imx_ic_prp_ops = {
+	.subdev_ops = &prp_subdev_ops,
+	.internal_ops = &prp_internal_ops,
+	.entity_ops = &prp_entity_ops,
+	.init = prp_init,
+	.remove = prp_remove,
+};
diff --git a/drivers/staging/media/imx/imx-ic-prpencvf.c b/drivers/staging/media/imx/imx-ic-prpencvf.c
new file mode 100644
index 0000000..bd89e9b
--- /dev/null
+++ b/drivers/staging/media/imx/imx-ic-prpencvf.c
@@ -0,0 +1,1219 @@
+/*
+ * V4L2 Capture IC Preprocess Subdev for Freescale i.MX5/6 SOC
+ *
+ * This subdevice handles capture of video frames from the CSI or VDIC,
+ * which are routed directly to the Image Converter preprocess tasks,
+ * for resizing, colorspace conversion, and rotation.
+ *
+ * Copyright (c) 2012-2017 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/timer.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-ioctl.h>
+#include <media/v4l2-mc.h>
+#include <media/v4l2-subdev.h>
+#include <media/imx.h>
+#include "imx-media.h"
+#include "imx-ic.h"
+
+/*
+ * Min/Max supported width and heights.
+ *
+ * We allow planar output, so we have to align width at the source pad
+ * by 16 pixels to meet IDMAC alignment requirements for possible planar
+ * output.
+ *
+ * TODO: move this into pad format negotiation, if capture device
+ * has not requested a planar format, we should allow 8 pixel
+ * alignment at the source pad.
+ */
+#define MIN_W_SINK  176
+#define MIN_H_SINK  144
+#define MAX_W_SINK 4096
+#define MAX_H_SINK 4096
+#define W_ALIGN_SINK  3 /* multiple of 8 pixels */
+#define H_ALIGN_SINK  1 /* multiple of 2 lines */
+
+#define MAX_W_SRC  1024
+#define MAX_H_SRC  1024
+#define W_ALIGN_SRC   4 /* multiple of 16 pixels */
+#define H_ALIGN_SRC   1 /* multiple of 2 lines */
+
+#define S_ALIGN       1 /* multiple of 2 */
+
+struct prp_priv {
+	struct imx_media_dev *md;
+	struct imx_ic_priv *ic_priv;
+	struct media_pad pad[PRPENCVF_NUM_PADS];
+	/* the video device at output pad */
+	struct imx_media_video_dev *vdev;
+
+	/* lock to protect all members below */
+	struct mutex lock;
+
+	/* IPU units we require */
+	struct ipu_soc *ipu;
+	struct ipu_ic *ic;
+	struct ipuv3_channel *out_ch;
+	struct ipuv3_channel *rot_in_ch;
+	struct ipuv3_channel *rot_out_ch;
+
+	/* active vb2 buffers to send to video dev sink */
+	struct imx_media_buffer *active_vb2_buf[2];
+	struct imx_media_dma_buf underrun_buf;
+
+	int ipu_buf_num;  /* ipu double buffer index: 0-1 */
+
+	/* the sink for the captured frames */
+	struct media_entity *sink;
+	/* the source subdev */
+	struct v4l2_subdev *src_sd;
+
+	/* the attached CSI at stream on */
+	struct v4l2_subdev *csi_sd;
+
+	struct v4l2_mbus_framefmt format_mbus[PRPENCVF_NUM_PADS];
+	const struct imx_media_pixfmt *cc[PRPENCVF_NUM_PADS];
+	struct v4l2_fract frame_interval;
+
+	struct imx_media_dma_buf rot_buf[2];
+
+	/* controls */
+	struct v4l2_ctrl_handler ctrl_hdlr;
+	int  rotation; /* degrees */
+	bool hflip;
+	bool vflip;
+
+	/* derived from rotation, hflip, vflip controls */
+	enum ipu_rotate_mode rot_mode;
+
+	spinlock_t irqlock; /* protect eof_irq handler */
+
+	struct timer_list eof_timeout_timer;
+	int eof_irq;
+	int nfb4eof_irq;
+
+	bool stream_on; /* streaming is on */
+	bool last_eof;  /* waiting for last EOF at stream off */
+	struct completion last_eof_comp;
+};
+
+static const struct prp_channels {
+	u32 out_ch;
+	u32 rot_in_ch;
+	u32 rot_out_ch;
+} prp_channel[] = {
+	[IC_TASK_ENCODER] = {
+		.out_ch = IPUV3_CHANNEL_IC_PRP_ENC_MEM,
+		.rot_in_ch = IPUV3_CHANNEL_MEM_ROT_ENC,
+		.rot_out_ch = IPUV3_CHANNEL_ROT_ENC_MEM,
+	},
+	[IC_TASK_VIEWFINDER] = {
+		.out_ch = IPUV3_CHANNEL_IC_PRP_VF_MEM,
+		.rot_in_ch = IPUV3_CHANNEL_MEM_ROT_VF,
+		.rot_out_ch = IPUV3_CHANNEL_ROT_VF_MEM,
+	},
+};
+
+static inline struct prp_priv *sd_to_priv(struct v4l2_subdev *sd)
+{
+	struct imx_ic_priv *ic_priv = v4l2_get_subdevdata(sd);
+
+	return ic_priv->task_priv;
+}
+
+static void prp_put_ipu_resources(struct prp_priv *priv)
+{
+	if (!IS_ERR_OR_NULL(priv->ic))
+		ipu_ic_put(priv->ic);
+	priv->ic = NULL;
+
+	if (!IS_ERR_OR_NULL(priv->out_ch))
+		ipu_idmac_put(priv->out_ch);
+	priv->out_ch = NULL;
+
+	if (!IS_ERR_OR_NULL(priv->rot_in_ch))
+		ipu_idmac_put(priv->rot_in_ch);
+	priv->rot_in_ch = NULL;
+
+	if (!IS_ERR_OR_NULL(priv->rot_out_ch))
+		ipu_idmac_put(priv->rot_out_ch);
+	priv->rot_out_ch = NULL;
+}
+
+static int prp_get_ipu_resources(struct prp_priv *priv)
+{
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+	int ret, task = ic_priv->task_id;
+
+	priv->ipu = priv->md->ipu[ic_priv->ipu_id];
+
+	priv->ic = ipu_ic_get(priv->ipu, task);
+	if (IS_ERR(priv->ic)) {
+		v4l2_err(&ic_priv->sd, "failed to get IC\n");
+		ret = PTR_ERR(priv->ic);
+		goto out;
+	}
+
+	priv->out_ch = ipu_idmac_get(priv->ipu,
+				     prp_channel[task].out_ch);
+	if (IS_ERR(priv->out_ch)) {
+		v4l2_err(&ic_priv->sd, "could not get IDMAC channel %u\n",
+			 prp_channel[task].out_ch);
+		ret = PTR_ERR(priv->out_ch);
+		goto out;
+	}
+
+	priv->rot_in_ch = ipu_idmac_get(priv->ipu,
+					prp_channel[task].rot_in_ch);
+	if (IS_ERR(priv->rot_in_ch)) {
+		v4l2_err(&ic_priv->sd, "could not get IDMAC channel %u\n",
+			 prp_channel[task].rot_in_ch);
+		ret = PTR_ERR(priv->rot_in_ch);
+		goto out;
+	}
+
+	priv->rot_out_ch = ipu_idmac_get(priv->ipu,
+					 prp_channel[task].rot_out_ch);
+	if (IS_ERR(priv->rot_out_ch)) {
+		v4l2_err(&ic_priv->sd, "could not get IDMAC channel %u\n",
+			 prp_channel[task].rot_out_ch);
+		ret = PTR_ERR(priv->rot_out_ch);
+		goto out;
+	}
+
+	return 0;
+out:
+	prp_put_ipu_resources(priv);
+	return ret;
+}
+
+static void prp_vb2_buf_done(struct prp_priv *priv, struct ipuv3_channel *ch)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct imx_media_buffer *done, *next;
+	struct vb2_buffer *vb;
+	dma_addr_t phys;
+
+	done = priv->active_vb2_buf[priv->ipu_buf_num];
+	if (done) {
+		vb = &done->vbuf.vb2_buf;
+		vb->timestamp = ktime_get_ns();
+		vb2_buffer_done(vb, VB2_BUF_STATE_DONE);
+	}
+
+	/* get next queued buffer */
+	next = imx_media_capture_device_next_buf(vdev);
+	if (next) {
+		phys = vb2_dma_contig_plane_dma_addr(&next->vbuf.vb2_buf, 0);
+		priv->active_vb2_buf[priv->ipu_buf_num] = next;
+	} else {
+		phys = priv->underrun_buf.phys;
+		priv->active_vb2_buf[priv->ipu_buf_num] = NULL;
+	}
+
+	if (ipu_idmac_buffer_is_ready(ch, priv->ipu_buf_num))
+		ipu_idmac_clear_buffer(ch, priv->ipu_buf_num);
+
+	ipu_cpmem_set_buffer(ch, priv->ipu_buf_num, phys);
+}
+
+static irqreturn_t prp_eof_interrupt(int irq, void *dev_id)
+{
+	struct prp_priv *priv = dev_id;
+	struct ipuv3_channel *channel;
+
+	spin_lock(&priv->irqlock);
+
+	if (priv->last_eof) {
+		complete(&priv->last_eof_comp);
+		priv->last_eof = false;
+		goto unlock;
+	}
+
+	/*
+	 * if there is a CSI in the pipeline, inform it of this EOF
+	 * so it can monitor frame intervals.
+	 */
+	if (priv->csi_sd)
+		v4l2_subdev_call(priv->csi_sd, core,
+				 interrupt_service_routine,
+				 0, NULL);
+
+	channel = (ipu_rot_mode_is_irt(priv->rot_mode)) ?
+		priv->rot_out_ch : priv->out_ch;
+
+	prp_vb2_buf_done(priv, channel);
+
+	/* select new IPU buf */
+	ipu_idmac_select_buffer(channel, priv->ipu_buf_num);
+	/* toggle IPU double-buffer index */
+	priv->ipu_buf_num ^= 1;
+
+	/* bump the EOF timeout timer */
+	mod_timer(&priv->eof_timeout_timer,
+		  jiffies + msecs_to_jiffies(IMX_MEDIA_EOF_TIMEOUT));
+
+unlock:
+	spin_unlock(&priv->irqlock);
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t prp_nfb4eof_interrupt(int irq, void *dev_id)
+{
+	struct prp_priv *priv = dev_id;
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+	static const struct v4l2_event ev = {
+		.type = V4L2_EVENT_NEW_FRAME_BEFORE_EOF,
+	};
+
+	v4l2_err(&ic_priv->sd, "NFB4EOF\n");
+
+	v4l2_subdev_notify_event(&ic_priv->sd, &ev);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * EOF timeout timer function.
+ */
+/*
+ * EOF timeout timer function. This is an unrecoverable condition
+ * without a stream restart.
+ */
+static void prp_eof_timeout(unsigned long data)
+{
+	struct prp_priv *priv = (struct prp_priv *)data;
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+
+	v4l2_err(&ic_priv->sd, "EOF timeout\n");
+
+	/* signal a fatal error to capture device */
+	imx_media_capture_device_error(vdev);
+}
+
+static void prp_setup_vb2_buf(struct prp_priv *priv, dma_addr_t *phys)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct imx_media_buffer *buf;
+	int i;
+
+	for (i = 0; i < 2; i++) {
+		buf = imx_media_capture_device_next_buf(vdev);
+		priv->active_vb2_buf[i] = buf;
+		phys[i] = vb2_dma_contig_plane_dma_addr(&buf->vbuf.vb2_buf, 0);
+	}
+}
+
+static void prp_unsetup_vb2_buf(struct prp_priv *priv,
+				enum vb2_buffer_state return_state)
+{
+	struct imx_media_buffer *buf;
+	int i;
+
+	/* return any remaining active frames with error */
+	for (i = 0; i < 2; i++) {
+		buf = priv->active_vb2_buf[i];
+		if (buf) {
+			struct vb2_buffer *vb = &buf->vbuf.vb2_buf;
+
+			vb->timestamp = ktime_get_ns();
+			vb2_buffer_done(vb, return_state);
+		}
+	}
+}
+
+static int prp_setup_channel(struct prp_priv *priv,
+			     struct ipuv3_channel *channel,
+			     enum ipu_rotate_mode rot_mode,
+			     dma_addr_t addr0, dma_addr_t addr1,
+			     bool rot_swap_width_height)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	const struct imx_media_pixfmt *outcc;
+	struct v4l2_mbus_framefmt *infmt;
+	unsigned int burst_size;
+	struct ipu_image image;
+	int ret;
+
+	infmt = &priv->format_mbus[PRPENCVF_SINK_PAD];
+	outcc = vdev->cc;
+
+	ipu_cpmem_zero(channel);
+
+	memset(&image, 0, sizeof(image));
+	image.pix = vdev->fmt.fmt.pix;
+	image.rect.width = image.pix.width;
+	image.rect.height = image.pix.height;
+
+	if (rot_swap_width_height) {
+		swap(image.pix.width, image.pix.height);
+		swap(image.rect.width, image.rect.height);
+		/* recalc stride using swapped width */
+		image.pix.bytesperline = outcc->planar ?
+			image.pix.width :
+			(image.pix.width * outcc->bpp) >> 3;
+	}
+
+	image.phys0 = addr0;
+	image.phys1 = addr1;
+
+	ret = ipu_cpmem_set_image(channel, &image);
+	if (ret)
+		return ret;
+
+	if (channel == priv->rot_in_ch ||
+	    channel == priv->rot_out_ch) {
+		burst_size = 8;
+		ipu_cpmem_set_block_mode(channel);
+	} else {
+		burst_size = (image.pix.width & 0xf) ? 8 : 16;
+	}
+
+	ipu_cpmem_set_burstsize(channel, burst_size);
+
+	if (rot_mode)
+		ipu_cpmem_set_rotation(channel, rot_mode);
+
+	if (image.pix.field == V4L2_FIELD_NONE &&
+	    V4L2_FIELD_HAS_BOTH(infmt->field) &&
+	    channel == priv->out_ch)
+		ipu_cpmem_interlaced_scan(channel, image.pix.bytesperline);
+
+	ret = ipu_ic_task_idma_init(priv->ic, channel,
+				    image.pix.width, image.pix.height,
+				    burst_size, rot_mode);
+	if (ret)
+		return ret;
+
+	ipu_cpmem_set_axi_id(channel, 1);
+
+	ipu_idmac_set_double_buffer(channel, true);
+
+	return 0;
+}
+
+static int prp_setup_rotation(struct prp_priv *priv)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+	const struct imx_media_pixfmt *outcc, *incc;
+	struct v4l2_mbus_framefmt *infmt;
+	struct v4l2_pix_format *outfmt;
+	dma_addr_t phys[2];
+	int ret;
+
+	infmt = &priv->format_mbus[PRPENCVF_SINK_PAD];
+	outfmt = &vdev->fmt.fmt.pix;
+	incc = priv->cc[PRPENCVF_SINK_PAD];
+	outcc = vdev->cc;
+
+	ret = imx_media_alloc_dma_buf(priv->md, &priv->rot_buf[0],
+				      outfmt->sizeimage);
+	if (ret) {
+		v4l2_err(&ic_priv->sd, "failed to alloc rot_buf[0], %d\n", ret);
+		return ret;
+	}
+	ret = imx_media_alloc_dma_buf(priv->md, &priv->rot_buf[1],
+				      outfmt->sizeimage);
+	if (ret) {
+		v4l2_err(&ic_priv->sd, "failed to alloc rot_buf[1], %d\n", ret);
+		goto free_rot0;
+	}
+
+	ret = ipu_ic_task_init(priv->ic,
+			       infmt->width, infmt->height,
+			       outfmt->height, outfmt->width,
+			       incc->cs, outcc->cs);
+	if (ret) {
+		v4l2_err(&ic_priv->sd, "ipu_ic_task_init failed, %d\n", ret);
+		goto free_rot1;
+	}
+
+	/* init the IC-PRP-->MEM IDMAC channel */
+	ret = prp_setup_channel(priv, priv->out_ch, IPU_ROTATE_NONE,
+				priv->rot_buf[0].phys, priv->rot_buf[1].phys,
+				true);
+	if (ret) {
+		v4l2_err(&ic_priv->sd,
+			 "prp_setup_channel(out_ch) failed, %d\n", ret);
+		goto free_rot1;
+	}
+
+	/* init the MEM-->IC-PRP ROT IDMAC channel */
+	ret = prp_setup_channel(priv, priv->rot_in_ch, priv->rot_mode,
+				priv->rot_buf[0].phys, priv->rot_buf[1].phys,
+				true);
+	if (ret) {
+		v4l2_err(&ic_priv->sd,
+			 "prp_setup_channel(rot_in_ch) failed, %d\n", ret);
+		goto free_rot1;
+	}
+
+	prp_setup_vb2_buf(priv, phys);
+
+	/* init the destination IC-PRP ROT-->MEM IDMAC channel */
+	ret = prp_setup_channel(priv, priv->rot_out_ch, IPU_ROTATE_NONE,
+				phys[0], phys[1],
+				false);
+	if (ret) {
+		v4l2_err(&ic_priv->sd,
+			 "prp_setup_channel(rot_out_ch) failed, %d\n", ret);
+		goto free_rot1;
+	}
+
+	/* now link IC-PRP-->MEM to MEM-->IC-PRP ROT */
+	ipu_idmac_link(priv->out_ch, priv->rot_in_ch);
+
+	/* enable the IC */
+	ipu_ic_enable(priv->ic);
+
+	/* set buffers ready */
+	ipu_idmac_select_buffer(priv->out_ch, 0);
+	ipu_idmac_select_buffer(priv->out_ch, 1);
+	ipu_idmac_select_buffer(priv->rot_out_ch, 0);
+	ipu_idmac_select_buffer(priv->rot_out_ch, 1);
+
+	/* enable the channels */
+	ipu_idmac_enable_channel(priv->out_ch);
+	ipu_idmac_enable_channel(priv->rot_in_ch);
+	ipu_idmac_enable_channel(priv->rot_out_ch);
+
+	/* and finally enable the IC PRP task */
+	ipu_ic_task_enable(priv->ic);
+
+	return 0;
+
+free_rot1:
+	imx_media_free_dma_buf(priv->md, &priv->rot_buf[1]);
+free_rot0:
+	imx_media_free_dma_buf(priv->md, &priv->rot_buf[0]);
+	return ret;
+}
+
+static void prp_unsetup_rotation(struct prp_priv *priv)
+{
+	ipu_ic_task_disable(priv->ic);
+
+	ipu_idmac_disable_channel(priv->out_ch);
+	ipu_idmac_disable_channel(priv->rot_in_ch);
+	ipu_idmac_disable_channel(priv->rot_out_ch);
+
+	ipu_idmac_unlink(priv->out_ch, priv->rot_in_ch);
+
+	ipu_ic_disable(priv->ic);
+
+	imx_media_free_dma_buf(priv->md, &priv->rot_buf[0]);
+	imx_media_free_dma_buf(priv->md, &priv->rot_buf[1]);
+}
+
+static int prp_setup_norotation(struct prp_priv *priv)
+{
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+	const struct imx_media_pixfmt *outcc, *incc;
+	struct v4l2_mbus_framefmt *infmt;
+	struct v4l2_pix_format *outfmt;
+	dma_addr_t phys[2];
+	int ret;
+
+	infmt = &priv->format_mbus[PRPENCVF_SINK_PAD];
+	outfmt = &vdev->fmt.fmt.pix;
+	incc = priv->cc[PRPENCVF_SINK_PAD];
+	outcc = vdev->cc;
+
+	ret = ipu_ic_task_init(priv->ic,
+			       infmt->width, infmt->height,
+			       outfmt->width, outfmt->height,
+			       incc->cs, outcc->cs);
+	if (ret) {
+		v4l2_err(&ic_priv->sd, "ipu_ic_task_init failed, %d\n", ret);
+		return ret;
+	}
+
+	prp_setup_vb2_buf(priv, phys);
+
+	/* init the IC PRP-->MEM IDMAC channel */
+	ret = prp_setup_channel(priv, priv->out_ch, priv->rot_mode,
+				phys[0], phys[1], false);
+	if (ret) {
+		v4l2_err(&ic_priv->sd,
+			 "prp_setup_channel(out_ch) failed, %d\n", ret);
+		return ret;
+	}
+
+	ipu_cpmem_dump(priv->out_ch);
+	ipu_ic_dump(priv->ic);
+	ipu_dump(priv->ipu);
+
+	ipu_ic_enable(priv->ic);
+
+	/* set buffers ready */
+	ipu_idmac_select_buffer(priv->out_ch, 0);
+	ipu_idmac_select_buffer(priv->out_ch, 1);
+
+	/* enable the channels */
+	ipu_idmac_enable_channel(priv->out_ch);
+
+	/* enable the IC task */
+	ipu_ic_task_enable(priv->ic);
+
+	return 0;
+}
+
+static void prp_unsetup_norotation(struct prp_priv *priv)
+{
+	ipu_ic_task_disable(priv->ic);
+	ipu_idmac_disable_channel(priv->out_ch);
+	ipu_ic_disable(priv->ic);
+}
+
+static void prp_unsetup(struct prp_priv *priv,
+			enum vb2_buffer_state state)
+{
+	if (ipu_rot_mode_is_irt(priv->rot_mode))
+		prp_unsetup_rotation(priv);
+	else
+		prp_unsetup_norotation(priv);
+
+	prp_unsetup_vb2_buf(priv, state);
+}
+
+static int prp_start(struct prp_priv *priv)
+{
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+	struct imx_media_video_dev *vdev = priv->vdev;
+	struct v4l2_pix_format *outfmt;
+	int ret;
+
+	ret = prp_get_ipu_resources(priv);
+	if (ret)
+		return ret;
+
+	outfmt = &vdev->fmt.fmt.pix;
+
+	ret = imx_media_alloc_dma_buf(priv->md, &priv->underrun_buf,
+				      outfmt->sizeimage);
+	if (ret)
+		goto out_put_ipu;
+
+	priv->ipu_buf_num = 0;
+
+	/* init EOF completion waitq */
+	init_completion(&priv->last_eof_comp);
+	priv->last_eof = false;
+
+	if (ipu_rot_mode_is_irt(priv->rot_mode))
+		ret = prp_setup_rotation(priv);
+	else
+		ret = prp_setup_norotation(priv);
+	if (ret)
+		goto out_free_underrun;
+
+	priv->nfb4eof_irq = ipu_idmac_channel_irq(priv->ipu,
+						  priv->out_ch,
+						  IPU_IRQ_NFB4EOF);
+	ret = devm_request_irq(ic_priv->dev, priv->nfb4eof_irq,
+			       prp_nfb4eof_interrupt, 0,
+			       "imx-ic-prp-nfb4eof", priv);
+	if (ret) {
+		v4l2_err(&ic_priv->sd,
+			 "Error registering NFB4EOF irq: %d\n", ret);
+		goto out_unsetup;
+	}
+
+	if (ipu_rot_mode_is_irt(priv->rot_mode))
+		priv->eof_irq = ipu_idmac_channel_irq(
+			priv->ipu, priv->rot_out_ch, IPU_IRQ_EOF);
+	else
+		priv->eof_irq = ipu_idmac_channel_irq(
+			priv->ipu, priv->out_ch, IPU_IRQ_EOF);
+
+	ret = devm_request_irq(ic_priv->dev, priv->eof_irq,
+			       prp_eof_interrupt, 0,
+			       "imx-ic-prp-eof", priv);
+	if (ret) {
+		v4l2_err(&ic_priv->sd,
+			 "Error registering eof irq: %d\n", ret);
+		goto out_free_nfb4eof_irq;
+	}
+
+	/* start the EOF timeout timer */
+	mod_timer(&priv->eof_timeout_timer,
+		  jiffies + msecs_to_jiffies(IMX_MEDIA_EOF_TIMEOUT));
+
+	return 0;
+
+out_free_nfb4eof_irq:
+	devm_free_irq(ic_priv->dev, priv->nfb4eof_irq, priv);
+out_unsetup:
+	prp_unsetup(priv, VB2_BUF_STATE_QUEUED);
+out_free_underrun:
+	imx_media_free_dma_buf(priv->md, &priv->underrun_buf);
+out_put_ipu:
+	prp_put_ipu_resources(priv);
+	return ret;
+}
+
+static void prp_stop(struct prp_priv *priv)
+{
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+	unsigned long flags;
+	int ret;
+
+	/* mark next EOF interrupt as the last before stream off */
+	spin_lock_irqsave(&priv->irqlock, flags);
+	priv->last_eof = true;
+	spin_unlock_irqrestore(&priv->irqlock, flags);
+
+	/*
+	 * and then wait for interrupt handler to mark completion.
+	 */
+	ret = wait_for_completion_timeout(
+		&priv->last_eof_comp,
+		msecs_to_jiffies(IMX_MEDIA_EOF_TIMEOUT));
+	if (ret == 0)
+		v4l2_warn(&ic_priv->sd, "wait last EOF timeout\n");
+
+	devm_free_irq(ic_priv->dev, priv->eof_irq, priv);
+	devm_free_irq(ic_priv->dev, priv->nfb4eof_irq, priv);
+
+	prp_unsetup(priv, VB2_BUF_STATE_ERROR);
+
+	imx_media_free_dma_buf(priv->md, &priv->underrun_buf);
+
+	/* cancel the EOF timeout timer */
+	del_timer_sync(&priv->eof_timeout_timer);
+
+	prp_put_ipu_resources(priv);
+}
+
+static int prp_enum_mbus_code(struct v4l2_subdev *sd,
+			      struct v4l2_subdev_pad_config *cfg,
+			      struct v4l2_subdev_mbus_code_enum *code)
+{
+	if (code->pad >= PRPENCVF_NUM_PADS)
+		return -EINVAL;
+
+	if (code->pad == PRPENCVF_SRC_PAD)
+		return imx_media_enum_format(NULL, &code->code, code->index,
+					     true, false);
+
+	return imx_media_enum_ipu_format(NULL, &code->code, code->index, true);
+}
+
+static struct v4l2_mbus_framefmt *
+__prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_pad_config *cfg,
+	      unsigned int pad, enum v4l2_subdev_format_whence which)
+{
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+
+	if (which == V4L2_SUBDEV_FORMAT_TRY)
+		return v4l2_subdev_get_try_format(&ic_priv->sd, cfg, pad);
+	else
+		return &priv->format_mbus[pad];
+}
+
+/*
+ * V4L2 subdev operations.
+ */
+
+static int prp_get_fmt(struct v4l2_subdev *sd,
+		       struct v4l2_subdev_pad_config *cfg,
+		       struct v4l2_subdev_format *sdformat)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+	struct v4l2_mbus_framefmt *fmt;
+	int ret = 0;
+
+	if (sdformat->pad >= PRPENCVF_NUM_PADS)
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	fmt = __prp_get_fmt(priv, cfg, sdformat->pad, sdformat->which);
+	if (!fmt) {
+		ret = -EINVAL;
+		goto out;
+	}
+
+	sdformat->format = *fmt;
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int prp_set_fmt(struct v4l2_subdev *sd,
+		       struct v4l2_subdev_pad_config *cfg,
+		       struct v4l2_subdev_format *sdformat)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+	const struct imx_media_pixfmt *cc;
+	struct v4l2_mbus_framefmt *infmt;
+	int ret = 0;
+	u32 code;
+
+	if (sdformat->pad >= PRPENCVF_NUM_PADS)
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	if (priv->stream_on) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	if (sdformat->pad == PRPENCVF_SRC_PAD) {
+		infmt = __prp_get_fmt(priv, cfg, PRPENCVF_SINK_PAD,
+				      sdformat->which);
+
+		cc = imx_media_find_format(0, sdformat->format.code,
+					   true, false);
+		if (!cc) {
+			imx_media_enum_format(NULL, &code, 0, true, false);
+			cc = imx_media_find_format(0, code, true, false);
+			sdformat->format.code = cc->codes[0];
+		}
+
+		if (sdformat->format.field != V4L2_FIELD_NONE)
+			sdformat->format.field = infmt->field;
+
+		/* IC resizer cannot downsize more than 4:1 */
+		if (ipu_rot_mode_is_irt(priv->rot_mode))
+			v4l_bound_align_image(&sdformat->format.width,
+					      infmt->height / 4, MAX_H_SRC,
+					      H_ALIGN_SRC,
+					      &sdformat->format.height,
+					      infmt->width / 4, MAX_W_SRC,
+					      W_ALIGN_SRC, S_ALIGN);
+		else
+			v4l_bound_align_image(&sdformat->format.width,
+					      infmt->width / 4, MAX_W_SRC,
+					      W_ALIGN_SRC,
+					      &sdformat->format.height,
+					      infmt->height / 4, MAX_H_SRC,
+					      H_ALIGN_SRC, S_ALIGN);
+	} else {
+		cc = imx_media_find_ipu_format(0, sdformat->format.code,
+					       true);
+		if (!cc) {
+			imx_media_enum_ipu_format(NULL, &code, 0, true);
+			cc = imx_media_find_ipu_format(0, code, true);
+			sdformat->format.code = cc->codes[0];
+		}
+
+		v4l_bound_align_image(&sdformat->format.width,
+				      MIN_W_SINK, MAX_W_SINK, W_ALIGN_SINK,
+				      &sdformat->format.height,
+				      MIN_H_SINK, MAX_H_SINK, H_ALIGN_SINK,
+				      S_ALIGN);
+	}
+
+	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
+		cfg->try_fmt = sdformat->format;
+	} else {
+		priv->format_mbus[sdformat->pad] = sdformat->format;
+		priv->cc[sdformat->pad] = cc;
+	}
+
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int prp_g_frame_interval(struct v4l2_subdev *sd,
+				struct v4l2_subdev_frame_interval *fi)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+
+	mutex_lock(&priv->lock);
+	fi->interval = priv->frame_interval;
+	mutex_unlock(&priv->lock);
+
+	return 0;
+}
+
+static int prp_s_frame_interval(struct v4l2_subdev *sd,
+				struct v4l2_subdev_frame_interval *fi)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+
+	mutex_lock(&priv->lock);
+
+	/* Output pads mirror active input pad, no limits on input pads */
+	if (fi->pad == PRPENCVF_SRC_PAD)
+		fi->interval = priv->frame_interval;
+
+	priv->frame_interval = fi->interval;
+
+	mutex_unlock(&priv->lock);
+
+	return 0;
+}
+
+static int prp_link_setup(struct media_entity *entity,
+			  const struct media_pad *local,
+			  const struct media_pad *remote, u32 flags)
+{
+	struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity);
+	struct imx_ic_priv *ic_priv = v4l2_get_subdevdata(sd);
+	struct prp_priv *priv = ic_priv->task_priv;
+	struct v4l2_subdev *remote_sd;
+	int ret = 0;
+
+	dev_dbg(ic_priv->dev, "link setup %s -> %s", remote->entity->name,
+		local->entity->name);
+
+	mutex_lock(&priv->lock);
+
+	if (local->flags & MEDIA_PAD_FL_SINK) {
+		if (!is_media_entity_v4l2_subdev(remote->entity)) {
+			ret = -EINVAL;
+			goto out;
+		}
+
+		remote_sd = media_entity_to_v4l2_subdev(remote->entity);
+
+		if (flags & MEDIA_LNK_FL_ENABLED) {
+			if (priv->src_sd) {
+				ret = -EBUSY;
+				goto out;
+			}
+			priv->src_sd = remote_sd;
+		} else {
+			priv->src_sd = NULL;
+		}
+
+		goto out;
+	}
+
+	/* this is the source pad */
+
+	/* the remote must be the device node */
+	if (!is_media_entity_v4l2_video_device(remote->entity)) {
+		ret = -EINVAL;
+		goto out;
+	}
+
+	if (flags & MEDIA_LNK_FL_ENABLED) {
+		if (priv->sink) {
+			ret = -EBUSY;
+			goto out;
+		}
+	} else {
+		priv->sink = NULL;
+		goto out;
+	}
+
+	priv->sink = remote->entity;
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int prp_link_validate(struct v4l2_subdev *sd,
+			     struct media_link *link,
+			     struct v4l2_subdev_format *source_fmt,
+			     struct v4l2_subdev_format *sink_fmt)
+{
+	struct imx_ic_priv *ic_priv = v4l2_get_subdevdata(sd);
+	struct prp_priv *priv = ic_priv->task_priv;
+	struct imx_media_subdev *csi;
+	int ret;
+
+	ret = v4l2_subdev_link_validate_default(sd, link,
+						source_fmt, sink_fmt);
+	if (ret)
+		return ret;
+
+	ret = v4l2_subdev_link_validate_frame_interval(link);
+	if (ret)
+		return ret;
+
+	csi = imx_media_find_pipeline_subdev(priv->md, &ic_priv->sd.entity,
+					     IMX_MEDIA_GRP_ID_CSI);
+	if (IS_ERR(csi))
+		csi = NULL;
+
+	mutex_lock(&priv->lock);
+	priv->csi_sd = csi ? csi->sd : NULL;
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int prp_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct prp_priv *priv = container_of(ctrl->handler,
+					       struct prp_priv, ctrl_hdlr);
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+	enum ipu_rotate_mode rot_mode;
+	int rotation, ret = 0;
+	bool hflip, vflip;
+
+	mutex_lock(&priv->lock);
+
+	rotation = priv->rotation;
+	hflip = priv->hflip;
+	vflip = priv->vflip;
+
+	switch (ctrl->id) {
+	case V4L2_CID_HFLIP:
+		hflip = (ctrl->val == 1);
+		break;
+	case V4L2_CID_VFLIP:
+		vflip = (ctrl->val == 1);
+		break;
+	case V4L2_CID_ROTATE:
+		rotation = ctrl->val;
+		break;
+	default:
+		v4l2_err(&ic_priv->sd, "Invalid control\n");
+		ret = -EINVAL;
+		goto out;
+	}
+
+	ret = ipu_degrees_to_rot_mode(&rot_mode, rotation, hflip, vflip);
+	if (ret)
+		goto out;
+
+	if (rot_mode != priv->rot_mode) {
+		/* can't change rotation mid-streaming */
+		if (priv->stream_on) {
+			ret = -EBUSY;
+			goto out;
+		}
+		priv->rot_mode = rot_mode;
+		priv->rotation = rotation;
+		priv->hflip = hflip;
+		priv->vflip = vflip;
+	}
+
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static const struct v4l2_ctrl_ops prp_ctrl_ops = {
+	.s_ctrl = prp_s_ctrl,
+};
+
+static int prp_init_controls(struct prp_priv *priv)
+{
+	struct imx_ic_priv *ic_priv = priv->ic_priv;
+	struct v4l2_ctrl_handler *hdlr = &priv->ctrl_hdlr;
+	int ret;
+
+	v4l2_ctrl_handler_init(hdlr, 3);
+
+	v4l2_ctrl_new_std(hdlr, &prp_ctrl_ops, V4L2_CID_HFLIP,
+			  0, 1, 1, 0);
+	v4l2_ctrl_new_std(hdlr, &prp_ctrl_ops, V4L2_CID_VFLIP,
+			  0, 1, 1, 0);
+	v4l2_ctrl_new_std(hdlr, &prp_ctrl_ops, V4L2_CID_ROTATE,
+			  0, 270, 90, 0);
+
+	ic_priv->sd.ctrl_handler = hdlr;
+
+	if (hdlr->error) {
+		ret = hdlr->error;
+		goto out_free;
+	}
+
+	v4l2_ctrl_handler_setup(hdlr);
+	return 0;
+
+out_free:
+	v4l2_ctrl_handler_free(hdlr);
+	return ret;
+}
+
+static int prp_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct imx_ic_priv *ic_priv = v4l2_get_subdevdata(sd);
+	struct prp_priv *priv = ic_priv->task_priv;
+	int ret = 0;
+
+	mutex_lock(&priv->lock);
+
+	if (!priv->src_sd || !priv->sink) {
+		ret = -EPIPE;
+		goto out;
+	}
+
+	dev_dbg(ic_priv->dev, "stream %s\n", enable ? "ON" : "OFF");
+
+	if (enable && !priv->stream_on)
+		ret = prp_start(priv);
+	else if (!enable && priv->stream_on)
+		prp_stop(priv);
+
+	if (!ret)
+		priv->stream_on = enable;
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int prp_subscribe_event(struct v4l2_subdev *sd, struct v4l2_fh *fh,
+			       struct v4l2_event_subscription *sub)
+{
+	if (sub->type != V4L2_EVENT_NEW_FRAME_BEFORE_EOF)
+		return -EINVAL;
+	if (sub->id != 0)
+		return -EINVAL;
+
+	return v4l2_event_subscribe(fh, sub, 0, NULL);
+}
+
+static int prp_unsubscribe_event(struct v4l2_subdev *sd, struct v4l2_fh *fh,
+				 struct v4l2_event_subscription *sub)
+{
+	return v4l2_event_unsubscribe(fh, sub);
+}
+
+/*
+ * retrieve our pads parsed from the OF graph by the media device
+ */
+static int prp_registered(struct v4l2_subdev *sd)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+	int i, ret;
+	u32 code;
+
+	/* get media device */
+	priv->md = dev_get_drvdata(sd->v4l2_dev->dev);
+
+	for (i = 0; i < PRPENCVF_NUM_PADS; i++) {
+		if (i == PRPENCVF_SINK_PAD) {
+			priv->pad[i].flags = MEDIA_PAD_FL_SINK;
+			imx_media_enum_ipu_format(NULL, &code, 0, true);
+		} else {
+			priv->pad[i].flags = MEDIA_PAD_FL_SOURCE;
+			code = 0;
+		}
+
+		/* set a default mbus format  */
+		ret = imx_media_init_mbus_fmt(&priv->format_mbus[i],
+					      640, 480, code, V4L2_FIELD_NONE,
+					      &priv->cc[i]);
+		if (ret)
+			return ret;
+	}
+
+	/* init default frame interval */
+	priv->frame_interval.numerator = 1;
+	priv->frame_interval.denominator = 30;
+
+	ret = media_entity_pads_init(&sd->entity, PRPENCVF_NUM_PADS,
+				     priv->pad);
+	if (ret)
+		return ret;
+
+	ret = imx_media_capture_device_register(priv->vdev);
+	if (ret)
+		return ret;
+
+	ret = prp_init_controls(priv);
+	if (ret)
+		imx_media_capture_device_unregister(priv->vdev);
+
+	return ret;
+}
+
+static void prp_unregistered(struct v4l2_subdev *sd)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+
+	imx_media_capture_device_unregister(priv->vdev);
+	v4l2_ctrl_handler_free(&priv->ctrl_hdlr);
+}
+
+static struct v4l2_subdev_pad_ops prp_pad_ops = {
+	.enum_mbus_code = prp_enum_mbus_code,
+	.get_fmt = prp_get_fmt,
+	.set_fmt = prp_set_fmt,
+	.link_validate = prp_link_validate,
+};
+
+static const struct v4l2_subdev_core_ops prp_core_ops = {
+	.subscribe_event = prp_subscribe_event,
+	.unsubscribe_event = prp_unsubscribe_event,
+};
+
+static struct v4l2_subdev_video_ops prp_video_ops = {
+	.s_stream = prp_s_stream,
+	.g_frame_interval = prp_g_frame_interval,
+	.s_frame_interval = prp_s_frame_interval,
+};
+
+static struct media_entity_operations prp_entity_ops = {
+	.link_setup = prp_link_setup,
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static struct v4l2_subdev_ops prp_subdev_ops = {
+	.core = &prp_core_ops,
+	.video = &prp_video_ops,
+	.pad = &prp_pad_ops,
+};
+
+static struct v4l2_subdev_internal_ops prp_internal_ops = {
+	.registered = prp_registered,
+	.unregistered = prp_unregistered,
+};
+
+static int prp_init(struct imx_ic_priv *ic_priv)
+{
+	struct prp_priv *priv;
+
+	priv = devm_kzalloc(ic_priv->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	ic_priv->task_priv = priv;
+	priv->ic_priv = ic_priv;
+
+	spin_lock_init(&priv->irqlock);
+	init_timer(&priv->eof_timeout_timer);
+	priv->eof_timeout_timer.data = (unsigned long)priv;
+	priv->eof_timeout_timer.function = prp_eof_timeout;
+
+	priv->vdev = imx_media_capture_device_init(&ic_priv->sd,
+						   PRPENCVF_SRC_PAD);
+	if (IS_ERR(priv->vdev))
+		return PTR_ERR(priv->vdev);
+
+	mutex_init(&priv->lock);
+
+	return 0;
+}
+
+static void prp_remove(struct imx_ic_priv *ic_priv)
+{
+	struct prp_priv *priv = ic_priv->task_priv;
+
+	mutex_destroy(&priv->lock);
+	imx_media_capture_device_remove(priv->vdev);
+}
+
+struct imx_ic_ops imx_ic_prpencvf_ops = {
+	.subdev_ops = &prp_subdev_ops,
+	.internal_ops = &prp_internal_ops,
+	.entity_ops = &prp_entity_ops,
+	.init = prp_init,
+	.remove = prp_remove,
+};
diff --git a/drivers/staging/media/imx/imx-ic.h b/drivers/staging/media/imx/imx-ic.h
new file mode 100644
index 0000000..5535111
--- /dev/null
+++ b/drivers/staging/media/imx/imx-ic.h
@@ -0,0 +1,38 @@
+/*
+ * V4L2 Image Converter Subdev for Freescale i.MX5/6 SOC
+ *
+ * Copyright (c) 2016 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#ifndef _IMX_IC_H
+#define _IMX_IC_H
+
+#include <media/v4l2-subdev.h>
+
+struct imx_ic_priv {
+	struct device *dev;
+	struct v4l2_subdev sd;
+	int    ipu_id;
+	int    task_id;
+	void   *prp_priv;
+	void   *task_priv;
+};
+
+struct imx_ic_ops {
+	struct v4l2_subdev_ops *subdev_ops;
+	struct v4l2_subdev_internal_ops *internal_ops;
+	struct media_entity_operations *entity_ops;
+
+	int (*init)(struct imx_ic_priv *ic_priv);
+	void (*remove)(struct imx_ic_priv *ic_priv);
+};
+
+extern struct imx_ic_ops imx_ic_prp_ops;
+extern struct imx_ic_ops imx_ic_prpencvf_ops;
+extern struct imx_ic_ops imx_ic_pp_ops;
+
+#endif
-- 
2.7.4

[PATCH v5 28/39] media: imx: Add MIPI CSI-2 Receiver subdev driver

[Steve Longerbeam]

Adds MIPI CSI-2 Receiver subdev driver. This subdev is required
for sensors with a MIPI CSI2 interface.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/Makefile         |   1 +
 drivers/staging/media/imx/imx6-mipi-csi2.c | 689 +++++++++++++++++++++++++++++
 2 files changed, 690 insertions(+)
 create mode 100644 drivers/staging/media/imx/imx6-mipi-csi2.c

diff --git a/drivers/staging/media/imx/Makefile b/drivers/staging/media/imx/Makefile
index 878a126..3569625 100644
--- a/drivers/staging/media/imx/Makefile
+++ b/drivers/staging/media/imx/Makefile
@@ -9,3 +9,4 @@ obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-vdic.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-ic.o
 
 obj-$(CONFIG_VIDEO_IMX_CSI) += imx-media-csi.o
+obj-$(CONFIG_VIDEO_IMX_CSI) += imx6-mipi-csi2.o
diff --git a/drivers/staging/media/imx/imx6-mipi-csi2.c b/drivers/staging/media/imx/imx6-mipi-csi2.c
new file mode 100644
index 0000000..1a71b40
--- /dev/null
+++ b/drivers/staging/media/imx/imx6-mipi-csi2.c
@@ -0,0 +1,689 @@
+/*
+ * MIPI CSI-2 Receiver Subdev for Freescale i.MX6 SOC.
+ *
+ * Copyright (c) 2012-2017 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-of.h>
+#include <media/v4l2-subdev.h>
+#include "imx-media.h"
+
+/*
+ * there must be 5 pads: 1 input pad from sensor, and
+ * the 4 virtual channel output pads
+ */
+#define CSI2_SINK_PAD       0
+#define CSI2_NUM_SINK_PADS  1
+#define CSI2_NUM_SRC_PADS   4
+#define CSI2_NUM_PADS       5
+
+/*
+ * The default maximum bit-rate per lane in Mbps, if the
+ * source subdev does not provide V4L2_CID_LINK_FREQ.
+ */
+#define CSI2_DEFAULT_MAX_MBPS 849
+
+struct csi2_dev {
+	struct device          *dev;
+	struct v4l2_subdev      sd;
+	struct media_pad       pad[CSI2_NUM_PADS];
+	struct clk             *dphy_clk;
+	struct clk             *pllref_clk;
+	struct clk             *pix_clk; /* what is this? */
+	void __iomem           *base;
+	struct v4l2_of_bus_mipi_csi2 bus;
+
+	/* lock to protect all members below */
+	struct mutex lock;
+
+	struct v4l2_mbus_framefmt format_mbus;
+
+	int                     power_count;
+	bool                    stream_on;
+	struct v4l2_subdev      *src_sd;
+	bool                    sink_linked[CSI2_NUM_SRC_PADS];
+};
+
+#define DEVICE_NAME "imx6-mipi-csi2"
+
+/* Register offsets */
+#define CSI2_VERSION            0x000
+#define CSI2_N_LANES            0x004
+#define CSI2_PHY_SHUTDOWNZ      0x008
+#define CSI2_DPHY_RSTZ          0x00c
+#define CSI2_RESETN             0x010
+#define CSI2_PHY_STATE          0x014
+#define PHY_STOPSTATEDATA_BIT   4
+#define PHY_STOPSTATEDATA(n)    BIT(PHY_STOPSTATEDATA_BIT + (n))
+#define PHY_RXCLKACTIVEHS       BIT(8)
+#define PHY_RXULPSCLKNOT        BIT(9)
+#define PHY_STOPSTATECLK        BIT(10)
+#define CSI2_DATA_IDS_1         0x018
+#define CSI2_DATA_IDS_2         0x01c
+#define CSI2_ERR1               0x020
+#define CSI2_ERR2               0x024
+#define CSI2_MSK1               0x028
+#define CSI2_MSK2               0x02c
+#define CSI2_PHY_TST_CTRL0      0x030
+#define PHY_TESTCLR		BIT(0)
+#define PHY_TESTCLK		BIT(1)
+#define CSI2_PHY_TST_CTRL1      0x034
+#define PHY_TESTEN		BIT(16)
+#define CSI2_SFT_RESET          0xf00
+
+static inline struct csi2_dev *sd_to_dev(struct v4l2_subdev *sdev)
+{
+	return container_of(sdev, struct csi2_dev, sd);
+}
+
+static void csi2_enable(struct csi2_dev *csi2, bool enable)
+{
+	if (enable) {
+		writel(0x1, csi2->base + CSI2_PHY_SHUTDOWNZ);
+		writel(0x1, csi2->base + CSI2_DPHY_RSTZ);
+		writel(0x1, csi2->base + CSI2_RESETN);
+	} else {
+		writel(0x0, csi2->base + CSI2_PHY_SHUTDOWNZ);
+		writel(0x0, csi2->base + CSI2_DPHY_RSTZ);
+		writel(0x0, csi2->base + CSI2_RESETN);
+	}
+}
+
+static void csi2_set_lanes(struct csi2_dev *csi2)
+{
+	int lanes = csi2->bus.num_data_lanes;
+
+	writel(lanes - 1, csi2->base + CSI2_N_LANES);
+}
+
+static void dw_mipi_csi2_phy_write(struct csi2_dev *csi2,
+				   u32 test_code, u32 test_data)
+{
+	/* Clear PHY test interface */
+	writel(PHY_TESTCLR, csi2->base + CSI2_PHY_TST_CTRL0);
+	writel(0x0, csi2->base + CSI2_PHY_TST_CTRL1);
+	writel(0x0, csi2->base + CSI2_PHY_TST_CTRL0);
+
+	/* Raise test interface strobe signal */
+	writel(PHY_TESTCLK, csi2->base + CSI2_PHY_TST_CTRL0);
+
+	/* Configure address write on falling edge and lower strobe signal */
+	writel(PHY_TESTEN | test_code, csi2->base + CSI2_PHY_TST_CTRL1);
+	writel(0x0, csi2->base + CSI2_PHY_TST_CTRL0);
+
+	/* Configure data write on rising edge and raise strobe signal */
+	writel(test_data, csi2->base + CSI2_PHY_TST_CTRL1);
+	writel(PHY_TESTCLK, csi2->base + CSI2_PHY_TST_CTRL0);
+
+	/* Clear strobe signal */
+	writel(0x0, csi2->base + CSI2_PHY_TST_CTRL0);
+}
+
+/*
+ * This table is based on the table documented at
+ * https://community.nxp.com/docs/DOC-94312. It assumes
+ * a 27MHz D-PHY pll reference clock.
+ */
+static const struct {
+	u32 max_mbps;
+	u32 hsfreqrange_sel;
+} hsfreq_map[] = {
+	{ 90, 0x00}, {100, 0x20}, {110, 0x40}, {125, 0x02},
+	{140, 0x22}, {150, 0x42}, {160, 0x04}, {180, 0x24},
+	{200, 0x44}, {210, 0x06}, {240, 0x26}, {250, 0x46},
+	{270, 0x08}, {300, 0x28}, {330, 0x48}, {360, 0x2a},
+	{400, 0x4a}, {450, 0x0c}, {500, 0x2c}, {550, 0x0e},
+	{600, 0x2e}, {650, 0x10}, {700, 0x30}, {750, 0x12},
+	{800, 0x32}, {850, 0x14}, {900, 0x34}, {950, 0x54},
+	{1000, 0x74},
+};
+
+static int max_mbps_to_hsfreqrange_sel(u32 max_mbps)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(hsfreq_map); i++)
+		if (hsfreq_map[i].max_mbps > max_mbps)
+			return hsfreq_map[i].hsfreqrange_sel;
+
+	return -EINVAL;
+}
+
+static int csi2_dphy_init(struct csi2_dev *csi2)
+{
+	struct v4l2_ctrl *ctrl;
+	u32 mbps_per_lane;
+	int sel;
+
+	ctrl = v4l2_ctrl_find(csi2->src_sd->ctrl_handler,
+			      V4L2_CID_LINK_FREQ);
+	if (!ctrl)
+		mbps_per_lane = CSI2_DEFAULT_MAX_MBPS;
+	else
+		mbps_per_lane = DIV_ROUND_UP_ULL(2 * ctrl->qmenu_int[ctrl->val],
+						 USEC_PER_SEC);
+
+	sel = max_mbps_to_hsfreqrange_sel(mbps_per_lane);
+	if (sel < 0)
+		return sel;
+
+	dw_mipi_csi2_phy_write(csi2, 0x44, sel);
+
+	return 0;
+}
+
+/*
+ * Waits for ultra-low-power state on D-PHY clock lane. This is currently
+ * unused and may not be needed at all, but keep around just in case.
+ */
+static int __maybe_unused csi2_dphy_wait_ulp(struct csi2_dev *csi2)
+{
+	u32 reg;
+	int ret;
+
+	/* wait for ULP on clock lane */
+	ret = readl_poll_timeout(csi2->base + CSI2_PHY_STATE, reg,
+				 !(reg & PHY_RXULPSCLKNOT), 0, 500000);
+	if (ret) {
+		v4l2_err(&csi2->sd, "ULP timeout, phy_state = 0x%08x\n", reg);
+		return ret;
+	}
+
+	/* wait until no errors on bus */
+	ret = readl_poll_timeout(csi2->base + CSI2_ERR1, reg,
+				 reg == 0x0, 0, 500000);
+	if (ret) {
+		v4l2_err(&csi2->sd, "stable bus timeout, err1 = 0x%08x\n", reg);
+		return ret;
+	}
+
+	return 0;
+}
+
+/* Waits for low-power LP-11 state on data and clock lanes. */
+static int csi2_dphy_wait_stopstate(struct csi2_dev *csi2)
+{
+	u32 mask, reg;
+	int ret;
+
+	mask = PHY_STOPSTATECLK |
+		((csi2->bus.num_data_lanes - 1) << PHY_STOPSTATEDATA_BIT);
+
+	ret = readl_poll_timeout(csi2->base + CSI2_PHY_STATE, reg,
+				 (reg & mask) == mask, 0, 500000);
+	if (ret) {
+		v4l2_err(&csi2->sd, "LP-11 timeout, phy_state = 0x%08x\n", reg);
+		return ret;
+	}
+
+	return 0;
+}
+
+/*
+ * Wait for active clock on the clock lane.
+ *
+ * FIXME: Currently unused, but it should be! It should be called
+ * from csi2_s_stream() below, at stream ON, but the required sequence
+ * of MIPI CSI-2 startup does not allow for an opportunity for this to
+ * be called. The sequence as specified in the i.MX6 reference manual
+ * is as follows:
+ *
+ * 1. Deassert presetn signal (global reset).
+ *        It's not clear what this "global reset" signal is (maybe APB
+ *        global reset), but in any case this step corresponds to
+ *        csi2_s_power(ON) here.
+ *
+ * 2. Configure MIPI Camera Sensor to put all Tx lanes in PL-11 state.
+ *        This must be carried out by the MIPI sensor's s_power(ON) subdev
+ *        op.
+ *
+ * 3. D-PHY initialization.
+ * 4. CSI2 Controller programming (Set N_LANES, deassert PHY_SHUTDOWNZ,
+ *    deassert PHY_RSTZ, deassert CSI2_RESETN).
+ * 5. Read the PHY status register (PHY_STATE) to confirm that all data and
+ *    clock lanes of the D-PHY are in Stop State.
+ *        These steps (3,4,5) are carried out by csi2_s_stream(ON) here.
+ *
+ * 6. Configure the MIPI Camera Sensor to start transmitting a clock on the
+ *    D-PHY clock lane.
+ *        This must be carried out by the MIPI sensor's s_stream(ON) subdev
+ *        op.
+ *
+ * 7. CSI2 Controller programming - Read the PHY status register (PHY_STATE)
+ *    to confirm that the D-PHY is receiving a clock on the D-PHY clock lane.
+ *        This is implemented by this unused function, and _should_ be called
+ *        by csi2_s_stream(ON) here, but csi2_s_stream(ON) has been taken up
+ *        by steps 3,4,5 above already.
+ *
+ * In summary, a temporary solution would require a hard-coded delay in the
+ * MIPI sensor's s_stream(ON) op, to allow time for a stable clock lane.
+ *
+ * A longer term solution might be to create a new subdev op, perhaps
+ * called prepare_stream, that can be implemented here, and would be
+ * assigned steps 3,4,5. Then csi2_s_stream(ON) would become available
+ * as step 7.
+ */
+static int __maybe_unused csi2_dphy_wait_clock_lane(struct csi2_dev *csi2)
+{
+	u32 reg;
+	int ret;
+
+	ret = readl_poll_timeout(csi2->base + CSI2_PHY_STATE, reg,
+				 (reg & PHY_RXCLKACTIVEHS), 0, 500000);
+	if (ret) {
+		v4l2_err(&csi2->sd, "clock lane timeout, phy_state = 0x%08x\n",
+			 reg);
+		return ret;
+	}
+
+	return 0;
+}
+
+/*
+ * V4L2 subdev operations.
+ */
+
+/* Startup Sequence Step 1 */
+static int csi2_s_power(struct v4l2_subdev *sd, int on)
+{
+	struct csi2_dev *csi2 = sd_to_dev(sd);
+	int ret = 0;
+
+	mutex_lock(&csi2->lock);
+
+	/*
+	 * If the power count is modified from 0 to != 0 or from != 0 to 0,
+	 * update the power state.
+	 */
+	if (csi2->power_count == !on) {
+		if (on) {
+			dev_dbg(csi2->dev, "power ON\n");
+			ret = clk_prepare_enable(csi2->pllref_clk);
+			if (ret)
+				goto out;
+			ret = clk_prepare_enable(csi2->dphy_clk);
+			if (ret) {
+				clk_disable_unprepare(csi2->pllref_clk);
+				goto out;
+			}
+		} else {
+			dev_dbg(csi2->dev, "power OFF\n");
+			clk_disable_unprepare(csi2->dphy_clk);
+			clk_disable_unprepare(csi2->pllref_clk);
+		}
+	}
+
+	/* Update the power count. */
+	csi2->power_count += on ? 1 : -1;
+	WARN_ON(csi2->power_count < 0);
+out:
+	mutex_unlock(&csi2->lock);
+	return ret;
+}
+
+/* Startup Sequence Steps 3, 4, 5 */
+static int csi2_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct csi2_dev *csi2 = sd_to_dev(sd);
+	int i, ret = 0;
+
+	mutex_lock(&csi2->lock);
+
+	if (!csi2->src_sd) {
+		ret = -EPIPE;
+		goto out;
+	}
+
+	for (i = 0; i < CSI2_NUM_SRC_PADS; i++) {
+		if (csi2->sink_linked[i])
+			break;
+	}
+	if (i >= CSI2_NUM_SRC_PADS) {
+		ret = -EPIPE;
+		goto out;
+	}
+
+	if (enable && !csi2->stream_on) {
+		dev_dbg(csi2->dev, "stream ON\n");
+
+		ret = clk_prepare_enable(csi2->pix_clk);
+		if (ret)
+			goto out;
+
+		/* Step 3 */
+		ret = csi2_dphy_init(csi2);
+		if (ret) {
+			clk_disable_unprepare(csi2->pix_clk);
+			goto out;
+		}
+
+		/* Step 4 */
+		csi2_set_lanes(csi2);
+		csi2_enable(csi2, true);
+
+		/* Step 5 */
+		ret = csi2_dphy_wait_stopstate(csi2);
+		if (ret) {
+			csi2_enable(csi2, false);
+			clk_disable_unprepare(csi2->pix_clk);
+			goto out;
+		}
+	} else if (!enable && csi2->stream_on) {
+		dev_dbg(csi2->dev, "stream OFF\n");
+		csi2_enable(csi2, false);
+		clk_disable_unprepare(csi2->pix_clk);
+	}
+
+	csi2->stream_on = enable;
+out:
+	mutex_unlock(&csi2->lock);
+	return ret;
+}
+
+static int csi2_link_setup(struct media_entity *entity,
+			   const struct media_pad *local,
+			   const struct media_pad *remote, u32 flags)
+{
+	struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity);
+	struct csi2_dev *csi2 = sd_to_dev(sd);
+	struct v4l2_subdev *remote_sd;
+	int ret = 0;
+
+	dev_dbg(csi2->dev, "link setup %s -> %s", remote->entity->name,
+		local->entity->name);
+
+	remote_sd = media_entity_to_v4l2_subdev(remote->entity);
+
+	mutex_lock(&csi2->lock);
+
+	if (local->flags & MEDIA_PAD_FL_SOURCE) {
+		if (flags & MEDIA_LNK_FL_ENABLED) {
+			if (csi2->sink_linked[local->index]) {
+				ret = -EBUSY;
+				goto out;
+			}
+			csi2->sink_linked[local->index] = true;
+		} else {
+			csi2->sink_linked[local->index] = false;
+		}
+	} else {
+		if (flags & MEDIA_LNK_FL_ENABLED) {
+			if (csi2->src_sd) {
+				ret = -EBUSY;
+				goto out;
+			}
+			csi2->src_sd = remote_sd;
+		} else {
+			csi2->src_sd = NULL;
+		}
+	}
+
+out:
+	mutex_unlock(&csi2->lock);
+	return ret;
+}
+
+static int csi2_get_fmt(struct v4l2_subdev *sd,
+			struct v4l2_subdev_pad_config *cfg,
+			struct v4l2_subdev_format *sdformat)
+{
+	struct csi2_dev *csi2 = sd_to_dev(sd);
+	struct v4l2_mbus_framefmt *fmt;
+
+	mutex_lock(&csi2->lock);
+
+	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY)
+		fmt = v4l2_subdev_get_try_format(&csi2->sd, cfg,
+						 sdformat->pad);
+	else
+		fmt = &csi2->format_mbus;
+
+	sdformat->format = *fmt;
+
+	mutex_unlock(&csi2->lock);
+
+	return 0;
+}
+
+static int csi2_set_fmt(struct v4l2_subdev *sd,
+			struct v4l2_subdev_pad_config *cfg,
+			struct v4l2_subdev_format *sdformat)
+{
+	struct csi2_dev *csi2 = sd_to_dev(sd);
+	int ret = 0;
+
+	if (sdformat->pad >= CSI2_NUM_PADS)
+		return -EINVAL;
+
+	mutex_lock(&csi2->lock);
+
+	if (csi2->stream_on) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	/* Output pads mirror active input pad, no limits on input pads */
+	if (sdformat->pad != CSI2_SINK_PAD)
+		sdformat->format = csi2->format_mbus;
+
+	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY)
+		cfg->try_fmt = sdformat->format;
+	else
+		csi2->format_mbus = sdformat->format;
+out:
+	mutex_unlock(&csi2->lock);
+	return ret;
+}
+
+static int csi2_link_validate(struct v4l2_subdev *sd,
+			      struct media_link *link,
+			      struct v4l2_subdev_format *source_fmt,
+			      struct v4l2_subdev_format *sink_fmt)
+{
+	int ret;
+
+	ret = v4l2_subdev_link_validate_default(sd, link,
+						source_fmt, sink_fmt);
+	if (ret)
+		return ret;
+
+	return v4l2_subdev_link_validate_frame_interval(link);
+}
+
+/*
+ * retrieve our pads parsed from the OF graph by the media device
+ */
+static int csi2_registered(struct v4l2_subdev *sd)
+{
+	struct csi2_dev *csi2 = sd_to_dev(sd);
+	int i, ret;
+
+	for (i = 0; i < CSI2_NUM_PADS; i++) {
+		csi2->pad[i].flags = (i == CSI2_SINK_PAD) ?
+		MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
+	}
+
+	/* set a default mbus format  */
+	ret = imx_media_init_mbus_fmt(&csi2->format_mbus,
+				      640, 480, 0, V4L2_FIELD_NONE, NULL);
+	if (ret)
+		return ret;
+
+	return media_entity_pads_init(&sd->entity, CSI2_NUM_PADS, csi2->pad);
+}
+
+static struct media_entity_operations csi2_entity_ops = {
+	.link_setup = csi2_link_setup,
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static struct v4l2_subdev_core_ops csi2_core_ops = {
+	.s_power = csi2_s_power,
+};
+
+static struct v4l2_subdev_video_ops csi2_video_ops = {
+	.s_stream = csi2_s_stream,
+};
+
+static struct v4l2_subdev_pad_ops csi2_pad_ops = {
+	.get_fmt = csi2_get_fmt,
+	.set_fmt = csi2_set_fmt,
+	.link_validate = csi2_link_validate,
+};
+
+static struct v4l2_subdev_ops csi2_subdev_ops = {
+	.core = &csi2_core_ops,
+	.video = &csi2_video_ops,
+	.pad = &csi2_pad_ops,
+};
+
+static struct v4l2_subdev_internal_ops csi2_internal_ops = {
+	.registered = csi2_registered,
+};
+
+static int csi2_parse_endpoints(struct csi2_dev *csi2)
+{
+	struct device_node *node = csi2->dev->of_node;
+	struct device_node *epnode;
+	struct v4l2_of_endpoint ep;
+
+	epnode = of_graph_get_endpoint_by_regs(node, 0, -1);
+	if (!epnode) {
+		v4l2_err(&csi2->sd, "failed to get sink endpoint node\n");
+		return -EINVAL;
+	}
+
+	v4l2_of_parse_endpoint(epnode, &ep);
+	of_node_put(epnode);
+
+	if (ep.bus_type != V4L2_MBUS_CSI2) {
+		v4l2_err(&csi2->sd, "invalid bus type, must be MIPI CSI2\n");
+		return -EINVAL;
+	}
+
+	csi2->bus = ep.bus.mipi_csi2;
+
+	dev_dbg(csi2->dev, "data lanes: %d\n", csi2->bus.num_data_lanes);
+	dev_dbg(csi2->dev, "flags: 0x%08x\n", csi2->bus.flags);
+	return 0;
+}
+
+static int csi2_probe(struct platform_device *pdev)
+{
+	struct csi2_dev *csi2;
+	struct resource *res;
+	int ret;
+
+	csi2 = devm_kzalloc(&pdev->dev, sizeof(*csi2), GFP_KERNEL);
+	if (!csi2)
+		return -ENOMEM;
+
+	csi2->dev = &pdev->dev;
+
+	v4l2_subdev_init(&csi2->sd, &csi2_subdev_ops);
+	v4l2_set_subdevdata(&csi2->sd, &pdev->dev);
+	csi2->sd.internal_ops = &csi2_internal_ops;
+	csi2->sd.entity.ops = &csi2_entity_ops;
+	csi2->sd.dev = &pdev->dev;
+	csi2->sd.owner = THIS_MODULE;
+	csi2->sd.flags = V4L2_SUBDEV_FL_HAS_DEVNODE;
+	strcpy(csi2->sd.name, DEVICE_NAME);
+	csi2->sd.entity.function = MEDIA_ENT_F_VID_IF_BRIDGE;
+	csi2->sd.grp_id = IMX_MEDIA_GRP_ID_CSI2;
+
+	ret = csi2_parse_endpoints(csi2);
+	if (ret)
+		return ret;
+
+	csi2->pllref_clk = devm_clk_get(&pdev->dev, "ref");
+	if (IS_ERR(csi2->pllref_clk)) {
+		v4l2_err(&csi2->sd, "failed to get pll reference clock\n");
+		ret = PTR_ERR(csi2->pllref_clk);
+		return ret;
+	}
+
+	csi2->dphy_clk = devm_clk_get(&pdev->dev, "dphy");
+	if (IS_ERR(csi2->dphy_clk)) {
+		v4l2_err(&csi2->sd, "failed to get dphy clock\n");
+		ret = PTR_ERR(csi2->dphy_clk);
+		return ret;
+	}
+
+	csi2->pix_clk = devm_clk_get(&pdev->dev, "pix");
+	if (IS_ERR(csi2->pix_clk)) {
+		v4l2_err(&csi2->sd, "failed to get pixel clock\n");
+		ret = PTR_ERR(csi2->pix_clk);
+		return ret;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		v4l2_err(&csi2->sd, "failed to get platform resources\n");
+		return -ENODEV;
+	}
+
+	csi2->base = devm_ioremap(&pdev->dev, res->start, PAGE_SIZE);
+	if (!csi2->base) {
+		v4l2_err(&csi2->sd, "failed to map CSI-2 registers\n");
+		return -ENOMEM;
+	}
+
+	mutex_init(&csi2->lock);
+
+	platform_set_drvdata(pdev, &csi2->sd);
+
+	ret = v4l2_async_register_subdev(&csi2->sd);
+	if (ret)
+		goto rmmutex;
+
+	return 0;
+
+rmmutex:
+	mutex_destroy(&csi2->lock);
+	return ret;
+}
+
+static int csi2_remove(struct platform_device *pdev)
+{
+	struct v4l2_subdev *sd = platform_get_drvdata(pdev);
+	struct csi2_dev *csi2 = sd_to_dev(sd);
+
+	v4l2_async_unregister_subdev(sd);
+	mutex_destroy(&csi2->lock);
+	media_entity_cleanup(&sd->entity);
+
+	return 0;
+}
+
+static const struct of_device_id csi2_dt_ids[] = {
+	{ .compatible = "fsl,imx6-mipi-csi2", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, csi2_dt_ids);
+
+static struct platform_driver csi2_driver = {
+	.driver = {
+		.name = DEVICE_NAME,
+		.of_match_table = csi2_dt_ids,
+	},
+	.probe = csi2_probe,
+	.remove = csi2_remove,
+};
+
+module_platform_driver(csi2_driver);
+
+MODULE_DESCRIPTION("i.MX5/6 MIPI CSI-2 Receiver driver");
+MODULE_AUTHOR("Steve Longerbeam <steve_longerbeam@mentor.com>");
+MODULE_LICENSE("GPL");
-- 
2.7.4

[PATCH v5 28/39] media: imx: Add MIPI CSI-2 Receiver subdev driver

[Steve Longerbeam]

Adds MIPI CSI-2 Receiver subdev driver. This subdev is required
for sensors with a MIPI CSI2 interface.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/Makefile         |   1 +
 drivers/staging/media/imx/imx6-mipi-csi2.c | 689 +++++++++++++++++++++++++++++
 2 files changed, 690 insertions(+)
 create mode 100644 drivers/staging/media/imx/imx6-mipi-csi2.c

diff --git a/drivers/staging/media/imx/Makefile b/drivers/staging/media/imx/Makefile
index 878a126..3569625 100644
--- a/drivers/staging/media/imx/Makefile
+++ b/drivers/staging/media/imx/Makefile
@@ -9,3 +9,4 @@ obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-vdic.o
 obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx-media-ic.o
 
 obj-$(CONFIG_VIDEO_IMX_CSI) += imx-media-csi.o
+obj-$(CONFIG_VIDEO_IMX_CSI) += imx6-mipi-csi2.o
diff --git a/drivers/staging/media/imx/imx6-mipi-csi2.c b/drivers/staging/media/imx/imx6-mipi-csi2.c
new file mode 100644
index 0000000..1a71b40
--- /dev/null
+++ b/drivers/staging/media/imx/imx6-mipi-csi2.c
@@ -0,0 +1,689 @@
+/*
+ * MIPI CSI-2 Receiver Subdev for Freescale i.MX6 SOC.
+ *
+ * Copyright (c) 2012-2017 Mentor Graphics Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-of.h>
+#include <media/v4l2-subdev.h>
+#include "imx-media.h"
+
+/*
+ * there must be 5 pads: 1 input pad from sensor, and
+ * the 4 virtual channel output pads
+ */
+#define CSI2_SINK_PAD       0
+#define CSI2_NUM_SINK_PADS  1
+#define CSI2_NUM_SRC_PADS   4
+#define CSI2_NUM_PADS       5
+
+/*
+ * The default maximum bit-rate per lane in Mbps, if the
+ * source subdev does not provide V4L2_CID_LINK_FREQ.
+ */
+#define CSI2_DEFAULT_MAX_MBPS 849
+
+struct csi2_dev {
+	struct device          *dev;
+	struct v4l2_subdev      sd;
+	struct media_pad       pad[CSI2_NUM_PADS];
+	struct clk             *dphy_clk;
+	struct clk             *pllref_clk;
+	struct clk             *pix_clk; /* what is this? */
+	void __iomem           *base;
+	struct v4l2_of_bus_mipi_csi2 bus;
+
+	/* lock to protect all members below */
+	struct mutex lock;
+
+	struct v4l2_mbus_framefmt format_mbus;
+
+	int                     power_count;
+	bool                    stream_on;
+	struct v4l2_subdev      *src_sd;
+	bool                    sink_linked[CSI2_NUM_SRC_PADS];
+};
+
+#define DEVICE_NAME "imx6-mipi-csi2"
+
+/* Register offsets */
+#define CSI2_VERSION            0x000
+#define CSI2_N_LANES            0x004
+#define CSI2_PHY_SHUTDOWNZ      0x008
+#define CSI2_DPHY_RSTZ          0x00c
+#define CSI2_RESETN             0x010
+#define CSI2_PHY_STATE          0x014
+#define PHY_STOPSTATEDATA_BIT   4
+#define PHY_STOPSTATEDATA(n)    BIT(PHY_STOPSTATEDATA_BIT + (n))
+#define PHY_RXCLKACTIVEHS       BIT(8)
+#define PHY_RXULPSCLKNOT        BIT(9)
+#define PHY_STOPSTATECLK        BIT(10)
+#define CSI2_DATA_IDS_1         0x018
+#define CSI2_DATA_IDS_2         0x01c
+#define CSI2_ERR1               0x020
+#define CSI2_ERR2               0x024
+#define CSI2_MSK1               0x028
+#define CSI2_MSK2               0x02c
+#define CSI2_PHY_TST_CTRL0      0x030
+#define PHY_TESTCLR		BIT(0)
+#define PHY_TESTCLK		BIT(1)
+#define CSI2_PHY_TST_CTRL1      0x034
+#define PHY_TESTEN		BIT(16)
+#define CSI2_SFT_RESET          0xf00
+
+static inline struct csi2_dev *sd_to_dev(struct v4l2_subdev *sdev)
+{
+	return container_of(sdev, struct csi2_dev, sd);
+}
+
+static void csi2_enable(struct csi2_dev *csi2, bool enable)
+{
+	if (enable) {
+		writel(0x1, csi2->base + CSI2_PHY_SHUTDOWNZ);
+		writel(0x1, csi2->base + CSI2_DPHY_RSTZ);
+		writel(0x1, csi2->base + CSI2_RESETN);
+	} else {
+		writel(0x0, csi2->base + CSI2_PHY_SHUTDOWNZ);
+		writel(0x0, csi2->base + CSI2_DPHY_RSTZ);
+		writel(0x0, csi2->base + CSI2_RESETN);
+	}
+}
+
+static void csi2_set_lanes(struct csi2_dev *csi2)
+{
+	int lanes = csi2->bus.num_data_lanes;
+
+	writel(lanes - 1, csi2->base + CSI2_N_LANES);
+}
+
+static void dw_mipi_csi2_phy_write(struct csi2_dev *csi2,
+				   u32 test_code, u32 test_data)
+{
+	/* Clear PHY test interface */
+	writel(PHY_TESTCLR, csi2->base + CSI2_PHY_TST_CTRL0);
+	writel(0x0, csi2->base + CSI2_PHY_TST_CTRL1);
+	writel(0x0, csi2->base + CSI2_PHY_TST_CTRL0);
+
+	/* Raise test interface strobe signal */
+	writel(PHY_TESTCLK, csi2->base + CSI2_PHY_TST_CTRL0);
+
+	/* Configure address write on falling edge and lower strobe signal */
+	writel(PHY_TESTEN | test_code, csi2->base + CSI2_PHY_TST_CTRL1);
+	writel(0x0, csi2->base + CSI2_PHY_TST_CTRL0);
+
+	/* Configure data write on rising edge and raise strobe signal */
+	writel(test_data, csi2->base + CSI2_PHY_TST_CTRL1);
+	writel(PHY_TESTCLK, csi2->base + CSI2_PHY_TST_CTRL0);
+
+	/* Clear strobe signal */
+	writel(0x0, csi2->base + CSI2_PHY_TST_CTRL0);
+}
+
+/*
+ * This table is based on the table documented at
+ * https://community.nxp.com/docs/DOC-94312. It assumes
+ * a 27MHz D-PHY pll reference clock.
+ */
+static const struct {
+	u32 max_mbps;
+	u32 hsfreqrange_sel;
+} hsfreq_map[] = {
+	{ 90, 0x00}, {100, 0x20}, {110, 0x40}, {125, 0x02},
+	{140, 0x22}, {150, 0x42}, {160, 0x04}, {180, 0x24},
+	{200, 0x44}, {210, 0x06}, {240, 0x26}, {250, 0x46},
+	{270, 0x08}, {300, 0x28}, {330, 0x48}, {360, 0x2a},
+	{400, 0x4a}, {450, 0x0c}, {500, 0x2c}, {550, 0x0e},
+	{600, 0x2e}, {650, 0x10}, {700, 0x30}, {750, 0x12},
+	{800, 0x32}, {850, 0x14}, {900, 0x34}, {950, 0x54},
+	{1000, 0x74},
+};
+
+static int max_mbps_to_hsfreqrange_sel(u32 max_mbps)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(hsfreq_map); i++)
+		if (hsfreq_map[i].max_mbps > max_mbps)
+			return hsfreq_map[i].hsfreqrange_sel;
+
+	return -EINVAL;
+}
+
+static int csi2_dphy_init(struct csi2_dev *csi2)
+{
+	struct v4l2_ctrl *ctrl;
+	u32 mbps_per_lane;
+	int sel;
+
+	ctrl = v4l2_ctrl_find(csi2->src_sd->ctrl_handler,
+			      V4L2_CID_LINK_FREQ);
+	if (!ctrl)
+		mbps_per_lane = CSI2_DEFAULT_MAX_MBPS;
+	else
+		mbps_per_lane = DIV_ROUND_UP_ULL(2 * ctrl->qmenu_int[ctrl->val],
+						 USEC_PER_SEC);
+
+	sel = max_mbps_to_hsfreqrange_sel(mbps_per_lane);
+	if (sel < 0)
+		return sel;
+
+	dw_mipi_csi2_phy_write(csi2, 0x44, sel);
+
+	return 0;
+}
+
+/*
+ * Waits for ultra-low-power state on D-PHY clock lane. This is currently
+ * unused and may not be needed@all, but keep around just in case.
+ */
+static int __maybe_unused csi2_dphy_wait_ulp(struct csi2_dev *csi2)
+{
+	u32 reg;
+	int ret;
+
+	/* wait for ULP on clock lane */
+	ret = readl_poll_timeout(csi2->base + CSI2_PHY_STATE, reg,
+				 !(reg & PHY_RXULPSCLKNOT), 0, 500000);
+	if (ret) {
+		v4l2_err(&csi2->sd, "ULP timeout, phy_state = 0x%08x\n", reg);
+		return ret;
+	}
+
+	/* wait until no errors on bus */
+	ret = readl_poll_timeout(csi2->base + CSI2_ERR1, reg,
+				 reg == 0x0, 0, 500000);
+	if (ret) {
+		v4l2_err(&csi2->sd, "stable bus timeout, err1 = 0x%08x\n", reg);
+		return ret;
+	}
+
+	return 0;
+}
+
+/* Waits for low-power LP-11 state on data and clock lanes. */
+static int csi2_dphy_wait_stopstate(struct csi2_dev *csi2)
+{
+	u32 mask, reg;
+	int ret;
+
+	mask = PHY_STOPSTATECLK |
+		((csi2->bus.num_data_lanes - 1) << PHY_STOPSTATEDATA_BIT);
+
+	ret = readl_poll_timeout(csi2->base + CSI2_PHY_STATE, reg,
+				 (reg & mask) == mask, 0, 500000);
+	if (ret) {
+		v4l2_err(&csi2->sd, "LP-11 timeout, phy_state = 0x%08x\n", reg);
+		return ret;
+	}
+
+	return 0;
+}
+
+/*
+ * Wait for active clock on the clock lane.
+ *
+ * FIXME: Currently unused, but it should be! It should be called
+ * from csi2_s_stream() below, at stream ON, but the required sequence
+ * of MIPI CSI-2 startup does not allow for an opportunity for this to
+ * be called. The sequence as specified in the i.MX6 reference manual
+ * is as follows:
+ *
+ * 1. Deassert presetn signal (global reset).
+ *        It's not clear what this "global reset" signal is (maybe APB
+ *        global reset), but in any case this step corresponds to
+ *        csi2_s_power(ON) here.
+ *
+ * 2. Configure MIPI Camera Sensor to put all Tx lanes in PL-11 state.
+ *        This must be carried out by the MIPI sensor's s_power(ON) subdev
+ *        op.
+ *
+ * 3. D-PHY initialization.
+ * 4. CSI2 Controller programming (Set N_LANES, deassert PHY_SHUTDOWNZ,
+ *    deassert PHY_RSTZ, deassert CSI2_RESETN).
+ * 5. Read the PHY status register (PHY_STATE) to confirm that all data and
+ *    clock lanes of the D-PHY are in Stop State.
+ *        These steps (3,4,5) are carried out by csi2_s_stream(ON) here.
+ *
+ * 6. Configure the MIPI Camera Sensor to start transmitting a clock on the
+ *    D-PHY clock lane.
+ *        This must be carried out by the MIPI sensor's s_stream(ON) subdev
+ *        op.
+ *
+ * 7. CSI2 Controller programming - Read the PHY status register (PHY_STATE)
+ *    to confirm that the D-PHY is receiving a clock on the D-PHY clock lane.
+ *        This is implemented by this unused function, and _should_ be called
+ *        by csi2_s_stream(ON) here, but csi2_s_stream(ON) has been taken up
+ *        by steps 3,4,5 above already.
+ *
+ * In summary, a temporary solution would require a hard-coded delay in the
+ * MIPI sensor's s_stream(ON) op, to allow time for a stable clock lane.
+ *
+ * A longer term solution might be to create a new subdev op, perhaps
+ * called prepare_stream, that can be implemented here, and would be
+ * assigned steps 3,4,5. Then csi2_s_stream(ON) would become available
+ * as step 7.
+ */
+static int __maybe_unused csi2_dphy_wait_clock_lane(struct csi2_dev *csi2)
+{
+	u32 reg;
+	int ret;
+
+	ret = readl_poll_timeout(csi2->base + CSI2_PHY_STATE, reg,
+				 (reg & PHY_RXCLKACTIVEHS), 0, 500000);
+	if (ret) {
+		v4l2_err(&csi2->sd, "clock lane timeout, phy_state = 0x%08x\n",
+			 reg);
+		return ret;
+	}
+
+	return 0;
+}
+
+/*
+ * V4L2 subdev operations.
+ */
+
+/* Startup Sequence Step 1 */
+static int csi2_s_power(struct v4l2_subdev *sd, int on)
+{
+	struct csi2_dev *csi2 = sd_to_dev(sd);
+	int ret = 0;
+
+	mutex_lock(&csi2->lock);
+
+	/*
+	 * If the power count is modified from 0 to != 0 or from != 0 to 0,
+	 * update the power state.
+	 */
+	if (csi2->power_count == !on) {
+		if (on) {
+			dev_dbg(csi2->dev, "power ON\n");
+			ret = clk_prepare_enable(csi2->pllref_clk);
+			if (ret)
+				goto out;
+			ret = clk_prepare_enable(csi2->dphy_clk);
+			if (ret) {
+				clk_disable_unprepare(csi2->pllref_clk);
+				goto out;
+			}
+		} else {
+			dev_dbg(csi2->dev, "power OFF\n");
+			clk_disable_unprepare(csi2->dphy_clk);
+			clk_disable_unprepare(csi2->pllref_clk);
+		}
+	}
+
+	/* Update the power count. */
+	csi2->power_count += on ? 1 : -1;
+	WARN_ON(csi2->power_count < 0);
+out:
+	mutex_unlock(&csi2->lock);
+	return ret;
+}
+
+/* Startup Sequence Steps 3, 4, 5 */
+static int csi2_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct csi2_dev *csi2 = sd_to_dev(sd);
+	int i, ret = 0;
+
+	mutex_lock(&csi2->lock);
+
+	if (!csi2->src_sd) {
+		ret = -EPIPE;
+		goto out;
+	}
+
+	for (i = 0; i < CSI2_NUM_SRC_PADS; i++) {
+		if (csi2->sink_linked[i])
+			break;
+	}
+	if (i >= CSI2_NUM_SRC_PADS) {
+		ret = -EPIPE;
+		goto out;
+	}
+
+	if (enable && !csi2->stream_on) {
+		dev_dbg(csi2->dev, "stream ON\n");
+
+		ret = clk_prepare_enable(csi2->pix_clk);
+		if (ret)
+			goto out;
+
+		/* Step 3 */
+		ret = csi2_dphy_init(csi2);
+		if (ret) {
+			clk_disable_unprepare(csi2->pix_clk);
+			goto out;
+		}
+
+		/* Step 4 */
+		csi2_set_lanes(csi2);
+		csi2_enable(csi2, true);
+
+		/* Step 5 */
+		ret = csi2_dphy_wait_stopstate(csi2);
+		if (ret) {
+			csi2_enable(csi2, false);
+			clk_disable_unprepare(csi2->pix_clk);
+			goto out;
+		}
+	} else if (!enable && csi2->stream_on) {
+		dev_dbg(csi2->dev, "stream OFF\n");
+		csi2_enable(csi2, false);
+		clk_disable_unprepare(csi2->pix_clk);
+	}
+
+	csi2->stream_on = enable;
+out:
+	mutex_unlock(&csi2->lock);
+	return ret;
+}
+
+static int csi2_link_setup(struct media_entity *entity,
+			   const struct media_pad *local,
+			   const struct media_pad *remote, u32 flags)
+{
+	struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity);
+	struct csi2_dev *csi2 = sd_to_dev(sd);
+	struct v4l2_subdev *remote_sd;
+	int ret = 0;
+
+	dev_dbg(csi2->dev, "link setup %s -> %s", remote->entity->name,
+		local->entity->name);
+
+	remote_sd = media_entity_to_v4l2_subdev(remote->entity);
+
+	mutex_lock(&csi2->lock);
+
+	if (local->flags & MEDIA_PAD_FL_SOURCE) {
+		if (flags & MEDIA_LNK_FL_ENABLED) {
+			if (csi2->sink_linked[local->index]) {
+				ret = -EBUSY;
+				goto out;
+			}
+			csi2->sink_linked[local->index] = true;
+		} else {
+			csi2->sink_linked[local->index] = false;
+		}
+	} else {
+		if (flags & MEDIA_LNK_FL_ENABLED) {
+			if (csi2->src_sd) {
+				ret = -EBUSY;
+				goto out;
+			}
+			csi2->src_sd = remote_sd;
+		} else {
+			csi2->src_sd = NULL;
+		}
+	}
+
+out:
+	mutex_unlock(&csi2->lock);
+	return ret;
+}
+
+static int csi2_get_fmt(struct v4l2_subdev *sd,
+			struct v4l2_subdev_pad_config *cfg,
+			struct v4l2_subdev_format *sdformat)
+{
+	struct csi2_dev *csi2 = sd_to_dev(sd);
+	struct v4l2_mbus_framefmt *fmt;
+
+	mutex_lock(&csi2->lock);
+
+	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY)
+		fmt = v4l2_subdev_get_try_format(&csi2->sd, cfg,
+						 sdformat->pad);
+	else
+		fmt = &csi2->format_mbus;
+
+	sdformat->format = *fmt;
+
+	mutex_unlock(&csi2->lock);
+
+	return 0;
+}
+
+static int csi2_set_fmt(struct v4l2_subdev *sd,
+			struct v4l2_subdev_pad_config *cfg,
+			struct v4l2_subdev_format *sdformat)
+{
+	struct csi2_dev *csi2 = sd_to_dev(sd);
+	int ret = 0;
+
+	if (sdformat->pad >= CSI2_NUM_PADS)
+		return -EINVAL;
+
+	mutex_lock(&csi2->lock);
+
+	if (csi2->stream_on) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	/* Output pads mirror active input pad, no limits on input pads */
+	if (sdformat->pad != CSI2_SINK_PAD)
+		sdformat->format = csi2->format_mbus;
+
+	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY)
+		cfg->try_fmt = sdformat->format;
+	else
+		csi2->format_mbus = sdformat->format;
+out:
+	mutex_unlock(&csi2->lock);
+	return ret;
+}
+
+static int csi2_link_validate(struct v4l2_subdev *sd,
+			      struct media_link *link,
+			      struct v4l2_subdev_format *source_fmt,
+			      struct v4l2_subdev_format *sink_fmt)
+{
+	int ret;
+
+	ret = v4l2_subdev_link_validate_default(sd, link,
+						source_fmt, sink_fmt);
+	if (ret)
+		return ret;
+
+	return v4l2_subdev_link_validate_frame_interval(link);
+}
+
+/*
+ * retrieve our pads parsed from the OF graph by the media device
+ */
+static int csi2_registered(struct v4l2_subdev *sd)
+{
+	struct csi2_dev *csi2 = sd_to_dev(sd);
+	int i, ret;
+
+	for (i = 0; i < CSI2_NUM_PADS; i++) {
+		csi2->pad[i].flags = (i == CSI2_SINK_PAD) ?
+		MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
+	}
+
+	/* set a default mbus format  */
+	ret = imx_media_init_mbus_fmt(&csi2->format_mbus,
+				      640, 480, 0, V4L2_FIELD_NONE, NULL);
+	if (ret)
+		return ret;
+
+	return media_entity_pads_init(&sd->entity, CSI2_NUM_PADS, csi2->pad);
+}
+
+static struct media_entity_operations csi2_entity_ops = {
+	.link_setup = csi2_link_setup,
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static struct v4l2_subdev_core_ops csi2_core_ops = {
+	.s_power = csi2_s_power,
+};
+
+static struct v4l2_subdev_video_ops csi2_video_ops = {
+	.s_stream = csi2_s_stream,
+};
+
+static struct v4l2_subdev_pad_ops csi2_pad_ops = {
+	.get_fmt = csi2_get_fmt,
+	.set_fmt = csi2_set_fmt,
+	.link_validate = csi2_link_validate,
+};
+
+static struct v4l2_subdev_ops csi2_subdev_ops = {
+	.core = &csi2_core_ops,
+	.video = &csi2_video_ops,
+	.pad = &csi2_pad_ops,
+};
+
+static struct v4l2_subdev_internal_ops csi2_internal_ops = {
+	.registered = csi2_registered,
+};
+
+static int csi2_parse_endpoints(struct csi2_dev *csi2)
+{
+	struct device_node *node = csi2->dev->of_node;
+	struct device_node *epnode;
+	struct v4l2_of_endpoint ep;
+
+	epnode = of_graph_get_endpoint_by_regs(node, 0, -1);
+	if (!epnode) {
+		v4l2_err(&csi2->sd, "failed to get sink endpoint node\n");
+		return -EINVAL;
+	}
+
+	v4l2_of_parse_endpoint(epnode, &ep);
+	of_node_put(epnode);
+
+	if (ep.bus_type != V4L2_MBUS_CSI2) {
+		v4l2_err(&csi2->sd, "invalid bus type, must be MIPI CSI2\n");
+		return -EINVAL;
+	}
+
+	csi2->bus = ep.bus.mipi_csi2;
+
+	dev_dbg(csi2->dev, "data lanes: %d\n", csi2->bus.num_data_lanes);
+	dev_dbg(csi2->dev, "flags: 0x%08x\n", csi2->bus.flags);
+	return 0;
+}
+
+static int csi2_probe(struct platform_device *pdev)
+{
+	struct csi2_dev *csi2;
+	struct resource *res;
+	int ret;
+
+	csi2 = devm_kzalloc(&pdev->dev, sizeof(*csi2), GFP_KERNEL);
+	if (!csi2)
+		return -ENOMEM;
+
+	csi2->dev = &pdev->dev;
+
+	v4l2_subdev_init(&csi2->sd, &csi2_subdev_ops);
+	v4l2_set_subdevdata(&csi2->sd, &pdev->dev);
+	csi2->sd.internal_ops = &csi2_internal_ops;
+	csi2->sd.entity.ops = &csi2_entity_ops;
+	csi2->sd.dev = &pdev->dev;
+	csi2->sd.owner = THIS_MODULE;
+	csi2->sd.flags = V4L2_SUBDEV_FL_HAS_DEVNODE;
+	strcpy(csi2->sd.name, DEVICE_NAME);
+	csi2->sd.entity.function = MEDIA_ENT_F_VID_IF_BRIDGE;
+	csi2->sd.grp_id = IMX_MEDIA_GRP_ID_CSI2;
+
+	ret = csi2_parse_endpoints(csi2);
+	if (ret)
+		return ret;
+
+	csi2->pllref_clk = devm_clk_get(&pdev->dev, "ref");
+	if (IS_ERR(csi2->pllref_clk)) {
+		v4l2_err(&csi2->sd, "failed to get pll reference clock\n");
+		ret = PTR_ERR(csi2->pllref_clk);
+		return ret;
+	}
+
+	csi2->dphy_clk = devm_clk_get(&pdev->dev, "dphy");
+	if (IS_ERR(csi2->dphy_clk)) {
+		v4l2_err(&csi2->sd, "failed to get dphy clock\n");
+		ret = PTR_ERR(csi2->dphy_clk);
+		return ret;
+	}
+
+	csi2->pix_clk = devm_clk_get(&pdev->dev, "pix");
+	if (IS_ERR(csi2->pix_clk)) {
+		v4l2_err(&csi2->sd, "failed to get pixel clock\n");
+		ret = PTR_ERR(csi2->pix_clk);
+		return ret;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		v4l2_err(&csi2->sd, "failed to get platform resources\n");
+		return -ENODEV;
+	}
+
+	csi2->base = devm_ioremap(&pdev->dev, res->start, PAGE_SIZE);
+	if (!csi2->base) {
+		v4l2_err(&csi2->sd, "failed to map CSI-2 registers\n");
+		return -ENOMEM;
+	}
+
+	mutex_init(&csi2->lock);
+
+	platform_set_drvdata(pdev, &csi2->sd);
+
+	ret = v4l2_async_register_subdev(&csi2->sd);
+	if (ret)
+		goto rmmutex;
+
+	return 0;
+
+rmmutex:
+	mutex_destroy(&csi2->lock);
+	return ret;
+}
+
+static int csi2_remove(struct platform_device *pdev)
+{
+	struct v4l2_subdev *sd = platform_get_drvdata(pdev);
+	struct csi2_dev *csi2 = sd_to_dev(sd);
+
+	v4l2_async_unregister_subdev(sd);
+	mutex_destroy(&csi2->lock);
+	media_entity_cleanup(&sd->entity);
+
+	return 0;
+}
+
+static const struct of_device_id csi2_dt_ids[] = {
+	{ .compatible = "fsl,imx6-mipi-csi2", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, csi2_dt_ids);
+
+static struct platform_driver csi2_driver = {
+	.driver = {
+		.name = DEVICE_NAME,
+		.of_match_table = csi2_dt_ids,
+	},
+	.probe = csi2_probe,
+	.remove = csi2_remove,
+};
+
+module_platform_driver(csi2_driver);
+
+MODULE_DESCRIPTION("i.MX5/6 MIPI CSI-2 Receiver driver");
+MODULE_AUTHOR("Steve Longerbeam <steve_longerbeam@mentor.com>");
+MODULE_LICENSE("GPL");
-- 
2.7.4

[PATCH v5 29/39] ARM: imx_v6_v7_defconfig: Enable staging video4linux drivers

[Steve Longerbeam]

Enable i.MX v4l2 media staging driver. For video capture on i.MX, the
video multiplexer subdev is required. On the SabreAuto, the ADV7180
video decoder is required along with i2c-mux-gpio. The Sabrelite
and SabreSD require the OV5640 and the SabreLite requires PWM clocks
for the OV5640.

Increase max zoneorder to allow larger video buffer allocations.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/configs/imx_v6_v7_defconfig | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig
index eaba3b1..5d8c94a 100644
--- a/arch/arm/configs/imx_v6_v7_defconfig
+++ b/arch/arm/configs/imx_v6_v7_defconfig
@@ -51,6 +51,7 @@ CONFIG_PREEMPT_VOLUNTARY=y
 CONFIG_AEABI=y
 CONFIG_HIGHMEM=y
 CONFIG_CMA=y
+CONFIG_FORCE_MAX_ZONEORDER=14
 CONFIG_CMDLINE="noinitrd console=ttymxc0,115200"
 CONFIG_KEXEC=y
 CONFIG_CPU_FREQ=y
@@ -181,6 +182,7 @@ CONFIG_SERIAL_FSL_LPUART=y
 CONFIG_SERIAL_FSL_LPUART_CONSOLE=y
 # CONFIG_I2C_COMPAT is not set
 CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_MUX=y
 CONFIG_I2C_MUX_GPIO=y
 # CONFIG_I2C_HELPER_AUTO is not set
 CONFIG_I2C_ALGOPCF=m
@@ -221,14 +223,20 @@ CONFIG_REGULATOR_PFUZE100=y
 CONFIG_MEDIA_SUPPORT=y
 CONFIG_MEDIA_CAMERA_SUPPORT=y
 CONFIG_MEDIA_RC_SUPPORT=y
+CONFIG_MEDIA_CONTROLLER=y
+CONFIG_VIDEO_V4L2_SUBDEV_API=y
 CONFIG_RC_DEVICES=y
 CONFIG_IR_GPIO_CIR=y
 CONFIG_MEDIA_USB_SUPPORT=y
 CONFIG_USB_VIDEO_CLASS=m
 CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_VIDEO_MULTIPLEXER=y
 CONFIG_SOC_CAMERA=y
 CONFIG_V4L_MEM2MEM_DRIVERS=y
 CONFIG_VIDEO_CODA=y
+# CONFIG_MEDIA_SUBDRV_AUTOSELECT is not set
+CONFIG_VIDEO_ADV7180=m
+CONFIG_VIDEO_OV5640=m
 CONFIG_SOC_CAMERA_OV2640=y
 CONFIG_IMX_IPUV3_CORE=y
 CONFIG_DRM=y
@@ -338,6 +346,9 @@ CONFIG_FSL_EDMA=y
 CONFIG_IMX_SDMA=y
 CONFIG_MXS_DMA=y
 CONFIG_STAGING=y
+CONFIG_STAGING_MEDIA=y
+CONFIG_VIDEO_IMX_MEDIA=y
+CONFIG_COMMON_CLK_PWM=y
 CONFIG_IIO=y
 CONFIG_VF610_ADC=y
 CONFIG_MPL3115=y
-- 
2.7.4

[PATCH v5 29/39] ARM: imx_v6_v7_defconfig: Enable staging video4linux drivers

[Steve Longerbeam]

Enable i.MX v4l2 media staging driver. For video capture on i.MX, the
video multiplexer subdev is required. On the SabreAuto, the ADV7180
video decoder is required along with i2c-mux-gpio. The Sabrelite
and SabreSD require the OV5640 and the SabreLite requires PWM clocks
for the OV5640.

Increase max zoneorder to allow larger video buffer allocations.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 arch/arm/configs/imx_v6_v7_defconfig | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig
index eaba3b1..5d8c94a 100644
--- a/arch/arm/configs/imx_v6_v7_defconfig
+++ b/arch/arm/configs/imx_v6_v7_defconfig
@@ -51,6 +51,7 @@ CONFIG_PREEMPT_VOLUNTARY=y
 CONFIG_AEABI=y
 CONFIG_HIGHMEM=y
 CONFIG_CMA=y
+CONFIG_FORCE_MAX_ZONEORDER=14
 CONFIG_CMDLINE="noinitrd console=ttymxc0,115200"
 CONFIG_KEXEC=y
 CONFIG_CPU_FREQ=y
@@ -181,6 +182,7 @@ CONFIG_SERIAL_FSL_LPUART=y
 CONFIG_SERIAL_FSL_LPUART_CONSOLE=y
 # CONFIG_I2C_COMPAT is not set
 CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_MUX=y
 CONFIG_I2C_MUX_GPIO=y
 # CONFIG_I2C_HELPER_AUTO is not set
 CONFIG_I2C_ALGOPCF=m
@@ -221,14 +223,20 @@ CONFIG_REGULATOR_PFUZE100=y
 CONFIG_MEDIA_SUPPORT=y
 CONFIG_MEDIA_CAMERA_SUPPORT=y
 CONFIG_MEDIA_RC_SUPPORT=y
+CONFIG_MEDIA_CONTROLLER=y
+CONFIG_VIDEO_V4L2_SUBDEV_API=y
 CONFIG_RC_DEVICES=y
 CONFIG_IR_GPIO_CIR=y
 CONFIG_MEDIA_USB_SUPPORT=y
 CONFIG_USB_VIDEO_CLASS=m
 CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_VIDEO_MULTIPLEXER=y
 CONFIG_SOC_CAMERA=y
 CONFIG_V4L_MEM2MEM_DRIVERS=y
 CONFIG_VIDEO_CODA=y
+# CONFIG_MEDIA_SUBDRV_AUTOSELECT is not set
+CONFIG_VIDEO_ADV7180=m
+CONFIG_VIDEO_OV5640=m
 CONFIG_SOC_CAMERA_OV2640=y
 CONFIG_IMX_IPUV3_CORE=y
 CONFIG_DRM=y
@@ -338,6 +346,9 @@ CONFIG_FSL_EDMA=y
 CONFIG_IMX_SDMA=y
 CONFIG_MXS_DMA=y
 CONFIG_STAGING=y
+CONFIG_STAGING_MEDIA=y
+CONFIG_VIDEO_IMX_MEDIA=y
+CONFIG_COMMON_CLK_PWM=y
 CONFIG_IIO=y
 CONFIG_VF610_ADC=y
 CONFIG_MPL3115=y
-- 
2.7.4

[PATCH v5 30/39] media: imx: add support for bayer formats

[Steve Longerbeam]

From: Russell King <rmk+kernel@armlinux.org.uk>

Add the bayer formats to imx-media's list of supported pixel and bus
formats.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

- added a bayer boolean to struct imx_media_pixfmt.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/imx-media-utils.c | 68 +++++++++++++++++++++++++++++
 drivers/staging/media/imx/imx-media.h       |  1 +
 2 files changed, 69 insertions(+)

diff --git a/drivers/staging/media/imx/imx-media-utils.c b/drivers/staging/media/imx/imx-media-utils.c
index ee50b6a..24e3795 100644
--- a/drivers/staging/media/imx/imx-media-utils.c
+++ b/drivers/staging/media/imx/imx-media-utils.c
@@ -61,6 +61,74 @@ static const struct imx_media_pixfmt imx_media_formats[] = {
 		.cs     = IPUV3_COLORSPACE_RGB,
 		.bpp    = 32,
 		.ipufmt = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SBGGR8,
+		.codes  = {MEDIA_BUS_FMT_SBGGR8_1X8},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 8,
+		.bayer  = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SGBRG8,
+		.codes  = {MEDIA_BUS_FMT_SGBRG8_1X8},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 8,
+		.bayer  = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SGRBG8,
+		.codes  = {MEDIA_BUS_FMT_SGRBG8_1X8},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 8,
+		.bayer  = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SRGGB8,
+		.codes  = {MEDIA_BUS_FMT_SRGGB8_1X8},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 8,
+		.bayer  = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SBGGR16,
+		.codes  = {
+			MEDIA_BUS_FMT_SBGGR10_1X10,
+			MEDIA_BUS_FMT_SBGGR12_1X12,
+			MEDIA_BUS_FMT_SBGGR14_1X14,
+			MEDIA_BUS_FMT_SBGGR16_1X16
+		},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 16,
+		.bayer  = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SGBRG16,
+		.codes  = {
+			MEDIA_BUS_FMT_SGBRG10_1X10,
+			MEDIA_BUS_FMT_SGBRG12_1X12,
+			MEDIA_BUS_FMT_SGBRG14_1X14,
+			MEDIA_BUS_FMT_SGBRG16_1X16,
+		},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 16,
+		.bayer  = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SGRBG16,
+		.codes  = {
+			MEDIA_BUS_FMT_SGRBG10_1X10,
+			MEDIA_BUS_FMT_SGRBG12_1X12,
+			MEDIA_BUS_FMT_SGRBG14_1X14,
+			MEDIA_BUS_FMT_SGRBG16_1X16,
+		},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 16,
+		.bayer  = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SRGGB16,
+		.codes  = {
+			MEDIA_BUS_FMT_SRGGB10_1X10,
+			MEDIA_BUS_FMT_SRGGB12_1X12,
+			MEDIA_BUS_FMT_SRGGB14_1X14,
+			MEDIA_BUS_FMT_SRGGB16_1X16,
+		},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 16,
+		.bayer  = true,
 	},
 	/*** non-mbus formats start here ***/
 	{
diff --git a/drivers/staging/media/imx/imx-media.h b/drivers/staging/media/imx/imx-media.h
index 2dd48ea..9e865fa 100644
--- a/drivers/staging/media/imx/imx-media.h
+++ b/drivers/staging/media/imx/imx-media.h
@@ -91,6 +91,7 @@ struct imx_media_pixfmt {
 	int     bpp;     /* total bpp */
 	enum ipu_color_space cs;
 	bool    planar;  /* is a planar format */
+	bool    bayer;   /* is a raw bayer format */
 	bool    ipufmt;  /* is one of the IPU internal formats */
 };
 
-- 
2.7.4

[PATCH v5 30/39] media: imx: add support for bayer formats

[Steve Longerbeam]

From: Russell King <rmk+kernel@armlinux.org.uk>

Add the bayer formats to imx-media's list of supported pixel and bus
formats.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

- added a bayer boolean to struct imx_media_pixfmt.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/imx-media-utils.c | 68 +++++++++++++++++++++++++++++
 drivers/staging/media/imx/imx-media.h       |  1 +
 2 files changed, 69 insertions(+)

diff --git a/drivers/staging/media/imx/imx-media-utils.c b/drivers/staging/media/imx/imx-media-utils.c
index ee50b6a..24e3795 100644
--- a/drivers/staging/media/imx/imx-media-utils.c
+++ b/drivers/staging/media/imx/imx-media-utils.c
@@ -61,6 +61,74 @@ static const struct imx_media_pixfmt imx_media_formats[] = {
 		.cs     = IPUV3_COLORSPACE_RGB,
 		.bpp    = 32,
 		.ipufmt = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SBGGR8,
+		.codes  = {MEDIA_BUS_FMT_SBGGR8_1X8},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 8,
+		.bayer  = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SGBRG8,
+		.codes  = {MEDIA_BUS_FMT_SGBRG8_1X8},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 8,
+		.bayer  = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SGRBG8,
+		.codes  = {MEDIA_BUS_FMT_SGRBG8_1X8},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 8,
+		.bayer  = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SRGGB8,
+		.codes  = {MEDIA_BUS_FMT_SRGGB8_1X8},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 8,
+		.bayer  = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SBGGR16,
+		.codes  = {
+			MEDIA_BUS_FMT_SBGGR10_1X10,
+			MEDIA_BUS_FMT_SBGGR12_1X12,
+			MEDIA_BUS_FMT_SBGGR14_1X14,
+			MEDIA_BUS_FMT_SBGGR16_1X16
+		},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 16,
+		.bayer  = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SGBRG16,
+		.codes  = {
+			MEDIA_BUS_FMT_SGBRG10_1X10,
+			MEDIA_BUS_FMT_SGBRG12_1X12,
+			MEDIA_BUS_FMT_SGBRG14_1X14,
+			MEDIA_BUS_FMT_SGBRG16_1X16,
+		},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 16,
+		.bayer  = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SGRBG16,
+		.codes  = {
+			MEDIA_BUS_FMT_SGRBG10_1X10,
+			MEDIA_BUS_FMT_SGRBG12_1X12,
+			MEDIA_BUS_FMT_SGRBG14_1X14,
+			MEDIA_BUS_FMT_SGRBG16_1X16,
+		},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 16,
+		.bayer  = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SRGGB16,
+		.codes  = {
+			MEDIA_BUS_FMT_SRGGB10_1X10,
+			MEDIA_BUS_FMT_SRGGB12_1X12,
+			MEDIA_BUS_FMT_SRGGB14_1X14,
+			MEDIA_BUS_FMT_SRGGB16_1X16,
+		},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 16,
+		.bayer  = true,
 	},
 	/*** non-mbus formats start here ***/
 	{
diff --git a/drivers/staging/media/imx/imx-media.h b/drivers/staging/media/imx/imx-media.h
index 2dd48ea..9e865fa 100644
--- a/drivers/staging/media/imx/imx-media.h
+++ b/drivers/staging/media/imx/imx-media.h
@@ -91,6 +91,7 @@ struct imx_media_pixfmt {
 	int     bpp;     /* total bpp */
 	enum ipu_color_space cs;
 	bool    planar;  /* is a planar format */
+	bool    bayer;   /* is a raw bayer format */
 	bool    ipufmt;  /* is one of the IPU internal formats */
 };
 
-- 
2.7.4

[PATCH v5 30/39] media: imx: add support for bayer formats

[Steve Longerbeam]

From: Russell King <rmk+kernel-I+IVW8TIWO2tmTQ+vhA3Yw@public.gmane.org>

Add the bayer formats to imx-media's list of supported pixel and bus
formats.

Signed-off-by: Russell King <rmk+kernel-I+IVW8TIWO2tmTQ+vhA3Yw@public.gmane.org>

- added a bayer boolean to struct imx_media_pixfmt.

Signed-off-by: Steve Longerbeam <steve_longerbeam-nmGgyN9QBj3QT0dZR+AlfA@public.gmane.org>
---
 drivers/staging/media/imx/imx-media-utils.c | 68 +++++++++++++++++++++++++++++
 drivers/staging/media/imx/imx-media.h       |  1 +
 2 files changed, 69 insertions(+)

diff --git a/drivers/staging/media/imx/imx-media-utils.c b/drivers/staging/media/imx/imx-media-utils.c
index ee50b6a..24e3795 100644
--- a/drivers/staging/media/imx/imx-media-utils.c
+++ b/drivers/staging/media/imx/imx-media-utils.c
@@ -61,6 +61,74 @@ static const struct imx_media_pixfmt imx_media_formats[] = {
 		.cs     = IPUV3_COLORSPACE_RGB,
 		.bpp    = 32,
 		.ipufmt = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SBGGR8,
+		.codes  = {MEDIA_BUS_FMT_SBGGR8_1X8},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 8,
+		.bayer  = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SGBRG8,
+		.codes  = {MEDIA_BUS_FMT_SGBRG8_1X8},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 8,
+		.bayer  = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SGRBG8,
+		.codes  = {MEDIA_BUS_FMT_SGRBG8_1X8},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 8,
+		.bayer  = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SRGGB8,
+		.codes  = {MEDIA_BUS_FMT_SRGGB8_1X8},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 8,
+		.bayer  = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SBGGR16,
+		.codes  = {
+			MEDIA_BUS_FMT_SBGGR10_1X10,
+			MEDIA_BUS_FMT_SBGGR12_1X12,
+			MEDIA_BUS_FMT_SBGGR14_1X14,
+			MEDIA_BUS_FMT_SBGGR16_1X16
+		},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 16,
+		.bayer  = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SGBRG16,
+		.codes  = {
+			MEDIA_BUS_FMT_SGBRG10_1X10,
+			MEDIA_BUS_FMT_SGBRG12_1X12,
+			MEDIA_BUS_FMT_SGBRG14_1X14,
+			MEDIA_BUS_FMT_SGBRG16_1X16,
+		},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 16,
+		.bayer  = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SGRBG16,
+		.codes  = {
+			MEDIA_BUS_FMT_SGRBG10_1X10,
+			MEDIA_BUS_FMT_SGRBG12_1X12,
+			MEDIA_BUS_FMT_SGRBG14_1X14,
+			MEDIA_BUS_FMT_SGRBG16_1X16,
+		},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 16,
+		.bayer  = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_SRGGB16,
+		.codes  = {
+			MEDIA_BUS_FMT_SRGGB10_1X10,
+			MEDIA_BUS_FMT_SRGGB12_1X12,
+			MEDIA_BUS_FMT_SRGGB14_1X14,
+			MEDIA_BUS_FMT_SRGGB16_1X16,
+		},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 16,
+		.bayer  = true,
 	},
 	/*** non-mbus formats start here ***/
 	{
diff --git a/drivers/staging/media/imx/imx-media.h b/drivers/staging/media/imx/imx-media.h
index 2dd48ea..9e865fa 100644
--- a/drivers/staging/media/imx/imx-media.h
+++ b/drivers/staging/media/imx/imx-media.h
@@ -91,6 +91,7 @@ struct imx_media_pixfmt {
 	int     bpp;     /* total bpp */
 	enum ipu_color_space cs;
 	bool    planar;  /* is a planar format */
+	bool    bayer;   /* is a raw bayer format */
 	bool    ipufmt;  /* is one of the IPU internal formats */
 };
 
-- 
2.7.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v5 31/39] media: imx: csi: add support for bayer formats

[Steve Longerbeam]

From: Russell King <rmk+kernel@armlinux.org.uk>

Bayer formats must be treated as generic data and passthrough mode must
be used.  Add the correct setup for these formats.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

- added check to csi_link_validate() to verify that destination is
  IDMAC output pad when passthrough conditions exist: bayer formats
  and 16-bit parallel buses.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/imx-media-csi.c | 52 +++++++++++++++++++++++++------
 1 file changed, 43 insertions(+), 9 deletions(-)

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index ab78ff7..a7d04e4 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -276,10 +276,11 @@ static int csi_idmac_setup_channel(struct csi_priv *priv)
 	struct imx_media_video_dev *vdev = priv->vdev;
 	struct v4l2_of_endpoint *sensor_ep;
 	struct v4l2_mbus_framefmt *infmt;
-	unsigned int burst_size;
 	struct ipu_image image;
+	u32 passthrough_bits;
 	dma_addr_t phys[2];
 	bool passthrough;
+	u32 burst_size;
 	int ret;
 
 	infmt = &priv->format_mbus[CSI_SINK_PAD];
@@ -306,15 +307,38 @@ static int csi_idmac_setup_channel(struct csi_priv *priv)
 	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
 
 	/*
-	 * If the sensor uses 16-bit parallel CSI bus, we must handle
-	 * the data internally in the IPU as 16-bit generic, aka
-	 * passthrough mode.
+	 * Check for conditions that require the IPU to handle the
+	 * data internally as generic data, aka passthrough mode:
+	 * - raw bayer formats
+	 * - the sensor bus is 16-bit parallel
 	 */
-	passthrough = (sensor_ep->bus_type != V4L2_MBUS_CSI2 &&
-		       sensor_ep->bus.parallel.bus_width >= 16);
+	switch (image.pix.pixelformat) {
+	case V4L2_PIX_FMT_SBGGR8:
+	case V4L2_PIX_FMT_SGBRG8:
+	case V4L2_PIX_FMT_SGRBG8:
+	case V4L2_PIX_FMT_SRGGB8:
+		burst_size = 8;
+		passthrough = true;
+		passthrough_bits = 8;
+		break;
+	case V4L2_PIX_FMT_SBGGR16:
+	case V4L2_PIX_FMT_SGBRG16:
+	case V4L2_PIX_FMT_SGRBG16:
+	case V4L2_PIX_FMT_SRGGB16:
+		burst_size = 4;
+		passthrough = true;
+		passthrough_bits = 16;
+		break;
+	default:
+		passthrough = (sensor_ep->bus_type != V4L2_MBUS_CSI2 &&
+			       sensor_ep->bus.parallel.bus_width >= 16);
+		passthrough_bits = 16;
+		break;
+	}
 
 	if (passthrough)
-		ipu_cpmem_set_format_passthrough(priv->idmac_ch, 16);
+		ipu_cpmem_set_format_passthrough(priv->idmac_ch,
+						 passthrough_bits);
 
 	/*
 	 * Set the channel for the direct CSI-->memory via SMFC
@@ -725,6 +749,7 @@ static int csi_link_validate(struct v4l2_subdev *sd,
 			     struct v4l2_subdev_format *sink_fmt)
 {
 	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	const struct imx_media_pixfmt *incc;
 	struct v4l2_of_endpoint *sensor_ep;
 	struct imx_media_subdev *sensor;
 	bool is_csi2;
@@ -749,8 +774,17 @@ static int csi_link_validate(struct v4l2_subdev *sd,
 
 	priv->sensor = sensor;
 	sensor_ep = &priv->sensor->sensor_ep;
-
 	is_csi2 = (sensor_ep->bus_type == V4L2_MBUS_CSI2);
+	incc = priv->cc[CSI_SINK_PAD];
+
+	if (priv->dest != IPU_CSI_DEST_IDMAC &&
+	    (incc->bayer || (!is_csi2 &&
+			     sensor_ep->bus.parallel.bus_width >= 16))) {
+		v4l2_err(&priv->sd,
+			 "bayer/16-bit parallel buses must go to IDMAC pad\n");
+		ret = -EINVAL;
+		goto out;
+	}
 
 	if (is_csi2) {
 		int vc_num = 0;
@@ -775,7 +809,7 @@ static int csi_link_validate(struct v4l2_subdev *sd,
 
 	/* select either parallel or MIPI-CSI2 as input to CSI */
 	ipu_set_csi_src_mux(priv->ipu, priv->csi_id, is_csi2);
-
+out:
 	mutex_unlock(&priv->lock);
 	return ret;
 }
-- 
2.7.4

[PATCH v5 31/39] media: imx: csi: add support for bayer formats

[Steve Longerbeam]

From: Russell King <rmk+kernel@armlinux.org.uk>

Bayer formats must be treated as generic data and passthrough mode must
be used.  Add the correct setup for these formats.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

- added check to csi_link_validate() to verify that destination is
  IDMAC output pad when passthrough conditions exist: bayer formats
  and 16-bit parallel buses.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/imx-media-csi.c | 52 +++++++++++++++++++++++++------
 1 file changed, 43 insertions(+), 9 deletions(-)

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index ab78ff7..a7d04e4 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -276,10 +276,11 @@ static int csi_idmac_setup_channel(struct csi_priv *priv)
 	struct imx_media_video_dev *vdev = priv->vdev;
 	struct v4l2_of_endpoint *sensor_ep;
 	struct v4l2_mbus_framefmt *infmt;
-	unsigned int burst_size;
 	struct ipu_image image;
+	u32 passthrough_bits;
 	dma_addr_t phys[2];
 	bool passthrough;
+	u32 burst_size;
 	int ret;
 
 	infmt = &priv->format_mbus[CSI_SINK_PAD];
@@ -306,15 +307,38 @@ static int csi_idmac_setup_channel(struct csi_priv *priv)
 	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
 
 	/*
-	 * If the sensor uses 16-bit parallel CSI bus, we must handle
-	 * the data internally in the IPU as 16-bit generic, aka
-	 * passthrough mode.
+	 * Check for conditions that require the IPU to handle the
+	 * data internally as generic data, aka passthrough mode:
+	 * - raw bayer formats
+	 * - the sensor bus is 16-bit parallel
 	 */
-	passthrough = (sensor_ep->bus_type != V4L2_MBUS_CSI2 &&
-		       sensor_ep->bus.parallel.bus_width >= 16);
+	switch (image.pix.pixelformat) {
+	case V4L2_PIX_FMT_SBGGR8:
+	case V4L2_PIX_FMT_SGBRG8:
+	case V4L2_PIX_FMT_SGRBG8:
+	case V4L2_PIX_FMT_SRGGB8:
+		burst_size = 8;
+		passthrough = true;
+		passthrough_bits = 8;
+		break;
+	case V4L2_PIX_FMT_SBGGR16:
+	case V4L2_PIX_FMT_SGBRG16:
+	case V4L2_PIX_FMT_SGRBG16:
+	case V4L2_PIX_FMT_SRGGB16:
+		burst_size = 4;
+		passthrough = true;
+		passthrough_bits = 16;
+		break;
+	default:
+		passthrough = (sensor_ep->bus_type != V4L2_MBUS_CSI2 &&
+			       sensor_ep->bus.parallel.bus_width >= 16);
+		passthrough_bits = 16;
+		break;
+	}
 
 	if (passthrough)
-		ipu_cpmem_set_format_passthrough(priv->idmac_ch, 16);
+		ipu_cpmem_set_format_passthrough(priv->idmac_ch,
+						 passthrough_bits);
 
 	/*
 	 * Set the channel for the direct CSI-->memory via SMFC
@@ -725,6 +749,7 @@ static int csi_link_validate(struct v4l2_subdev *sd,
 			     struct v4l2_subdev_format *sink_fmt)
 {
 	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	const struct imx_media_pixfmt *incc;
 	struct v4l2_of_endpoint *sensor_ep;
 	struct imx_media_subdev *sensor;
 	bool is_csi2;
@@ -749,8 +774,17 @@ static int csi_link_validate(struct v4l2_subdev *sd,
 
 	priv->sensor = sensor;
 	sensor_ep = &priv->sensor->sensor_ep;
-
 	is_csi2 = (sensor_ep->bus_type == V4L2_MBUS_CSI2);
+	incc = priv->cc[CSI_SINK_PAD];
+
+	if (priv->dest != IPU_CSI_DEST_IDMAC &&
+	    (incc->bayer || (!is_csi2 &&
+			     sensor_ep->bus.parallel.bus_width >= 16))) {
+		v4l2_err(&priv->sd,
+			 "bayer/16-bit parallel buses must go to IDMAC pad\n");
+		ret = -EINVAL;
+		goto out;
+	}
 
 	if (is_csi2) {
 		int vc_num = 0;
@@ -775,7 +809,7 @@ static int csi_link_validate(struct v4l2_subdev *sd,
 
 	/* select either parallel or MIPI-CSI2 as input to CSI */
 	ipu_set_csi_src_mux(priv->ipu, priv->csi_id, is_csi2);
-
+out:
 	mutex_unlock(&priv->lock);
 	return ret;
 }
-- 
2.7.4

[PATCH v5 32/39] media: imx: csi: fix crop rectangle changes in set_fmt

[Steve Longerbeam]

From: Philipp Zabel <p.zabel@pengutronix.de>

The cropping rectangle was being modified by the output pad's
set_fmt, which is the wrong pad to do this. The crop rectangle
should not be modified by the output pad set_fmt. It instead
should be reset to the full input frame when the input pad format
is set.

The output pad set_fmt should set width/height to the current
crop dimensions, or 1/2 the crop width/height to enable
downscaling.

So the other part of this patch is to enable downscaling if
the output pad dimension(s) are 1/2 the crop dimension(s) at
csi_setup() time.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/imx-media-csi.c | 35 ++++++++++++++++++++-----------
 1 file changed, 23 insertions(+), 12 deletions(-)

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index a7d04e4..577038e 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -536,6 +536,10 @@ static int csi_setup(struct csi_priv *priv)
 
 	ipu_csi_set_window(priv->csi, &priv->crop);
 
+	ipu_csi_set_downsize(priv->csi,
+			     priv->crop.width == 2 * outfmt->width,
+			     priv->crop.height == 2 * outfmt->height);
+
 	ipu_csi_init_interface(priv->csi, &sensor_mbus_cfg, &if_fmt);
 
 	ipu_csi_set_dest(priv->csi, priv->dest);
@@ -932,15 +936,15 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 	switch (sdformat->pad) {
 	case CSI_SRC_PAD_DIRECT:
 	case CSI_SRC_PAD_IDMAC:
-		crop.left = priv->crop.left;
-		crop.top = priv->crop.top;
-		crop.width = sdformat->format.width;
-		crop.height = sdformat->format.height;
-		ret = csi_try_crop(priv, &crop, sensor);
-		if (ret)
-			goto out;
-		sdformat->format.width = crop.width;
-		sdformat->format.height = crop.height;
+		if (sdformat->format.width < priv->crop.width * 3 / 4)
+			sdformat->format.width = priv->crop.width / 2;
+		else
+			sdformat->format.width = priv->crop.width;
+
+		if (sdformat->format.height < priv->crop.height * 3 / 4)
+			sdformat->format.height = priv->crop.height / 2;
+		else
+			sdformat->format.height = priv->crop.height;
 
 		if (sdformat->pad == CSI_SRC_PAD_IDMAC) {
 			cc = imx_media_find_format(0, sdformat->format.code,
@@ -986,6 +990,14 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 		}
 		break;
 	case CSI_SINK_PAD:
+		crop.left = 0;
+		crop.top = 0;
+		crop.width = sdformat->format.width;
+		crop.height = sdformat->format.height;
+		ret = csi_try_crop(priv, &crop, sensor);
+		if (ret)
+			goto out;
+
 		cc = imx_media_find_format(0, sdformat->format.code,
 					   true, false);
 		if (!cc) {
@@ -1004,9 +1016,8 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 	} else {
 		priv->format_mbus[sdformat->pad] = sdformat->format;
 		priv->cc[sdformat->pad] = cc;
-		/* Update the crop window if this is an output pad  */
-		if (sdformat->pad == CSI_SRC_PAD_DIRECT ||
-		    sdformat->pad == CSI_SRC_PAD_IDMAC)
+		/* Reset the crop window if this is the input pad */
+		if (sdformat->pad == CSI_SINK_PAD)
 			priv->crop = crop;
 	}
 
-- 
2.7.4

[PATCH v5 32/39] media: imx: csi: fix crop rectangle changes in set_fmt

[Steve Longerbeam]

From: Philipp Zabel <p.zabel@pengutronix.de>

The cropping rectangle was being modified by the output pad's
set_fmt, which is the wrong pad to do this. The crop rectangle
should not be modified by the output pad set_fmt. It instead
should be reset to the full input frame when the input pad format
is set.

The output pad set_fmt should set width/height to the current
crop dimensions, or 1/2 the crop width/height to enable
downscaling.

So the other part of this patch is to enable downscaling if
the output pad dimension(s) are 1/2 the crop dimension(s) at
csi_setup() time.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/imx-media-csi.c | 35 ++++++++++++++++++++-----------
 1 file changed, 23 insertions(+), 12 deletions(-)

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index a7d04e4..577038e 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -536,6 +536,10 @@ static int csi_setup(struct csi_priv *priv)
 
 	ipu_csi_set_window(priv->csi, &priv->crop);
 
+	ipu_csi_set_downsize(priv->csi,
+			     priv->crop.width == 2 * outfmt->width,
+			     priv->crop.height == 2 * outfmt->height);
+
 	ipu_csi_init_interface(priv->csi, &sensor_mbus_cfg, &if_fmt);
 
 	ipu_csi_set_dest(priv->csi, priv->dest);
@@ -932,15 +936,15 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 	switch (sdformat->pad) {
 	case CSI_SRC_PAD_DIRECT:
 	case CSI_SRC_PAD_IDMAC:
-		crop.left = priv->crop.left;
-		crop.top = priv->crop.top;
-		crop.width = sdformat->format.width;
-		crop.height = sdformat->format.height;
-		ret = csi_try_crop(priv, &crop, sensor);
-		if (ret)
-			goto out;
-		sdformat->format.width = crop.width;
-		sdformat->format.height = crop.height;
+		if (sdformat->format.width < priv->crop.width * 3 / 4)
+			sdformat->format.width = priv->crop.width / 2;
+		else
+			sdformat->format.width = priv->crop.width;
+
+		if (sdformat->format.height < priv->crop.height * 3 / 4)
+			sdformat->format.height = priv->crop.height / 2;
+		else
+			sdformat->format.height = priv->crop.height;
 
 		if (sdformat->pad == CSI_SRC_PAD_IDMAC) {
 			cc = imx_media_find_format(0, sdformat->format.code,
@@ -986,6 +990,14 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 		}
 		break;
 	case CSI_SINK_PAD:
+		crop.left = 0;
+		crop.top = 0;
+		crop.width = sdformat->format.width;
+		crop.height = sdformat->format.height;
+		ret = csi_try_crop(priv, &crop, sensor);
+		if (ret)
+			goto out;
+
 		cc = imx_media_find_format(0, sdformat->format.code,
 					   true, false);
 		if (!cc) {
@@ -1004,9 +1016,8 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 	} else {
 		priv->format_mbus[sdformat->pad] = sdformat->format;
 		priv->cc[sdformat->pad] = cc;
-		/* Update the crop window if this is an output pad  */
-		if (sdformat->pad == CSI_SRC_PAD_DIRECT ||
-		    sdformat->pad == CSI_SRC_PAD_IDMAC)
+		/* Reset the crop window if this is the input pad */
+		if (sdformat->pad == CSI_SINK_PAD)
 			priv->crop = crop;
 	}
 
-- 
2.7.4

[PATCH v5 33/39] media: imx: mipi-csi2: enable setting and getting of frame rates

[Steve Longerbeam]

From: Russell King <rmk+kernel@armlinux.org.uk>

Setting and getting frame rates is part of the negotiation mechanism
between subdevs.  The lack of support means that a frame rate at the
sensor can't be negotiated through the subdev path.

Add support at MIPI CSI2 level for handling this part of the
negotiation.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/imx6-mipi-csi2.c | 36 ++++++++++++++++++++++++++++++
 1 file changed, 36 insertions(+)

diff --git a/drivers/staging/media/imx/imx6-mipi-csi2.c b/drivers/staging/media/imx/imx6-mipi-csi2.c
index 1a71b40..d8f931e 100644
--- a/drivers/staging/media/imx/imx6-mipi-csi2.c
+++ b/drivers/staging/media/imx/imx6-mipi-csi2.c
@@ -49,6 +49,7 @@ struct csi2_dev {
 	struct mutex lock;
 
 	struct v4l2_mbus_framefmt format_mbus;
+	struct v4l2_fract frame_interval;
 
 	int                     power_count;
 	bool                    stream_on;
@@ -487,6 +488,35 @@ static int csi2_set_fmt(struct v4l2_subdev *sd,
 	return ret;
 }
 
+static int csi2_g_frame_interval(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_frame_interval *fi)
+{
+	struct csi2_dev *csi2 = sd_to_dev(sd);
+
+	mutex_lock(&csi2->lock);
+	fi->interval = csi2->frame_interval;
+	mutex_unlock(&csi2->lock);
+
+	return 0;
+}
+
+static int csi2_s_frame_interval(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_frame_interval *fi)
+{
+	struct csi2_dev *csi2 = sd_to_dev(sd);
+
+	mutex_lock(&csi2->lock);
+
+	/* Output pads mirror active input pad, no limits on input pads */
+	if (fi->pad != CSI2_SINK_PAD)
+		fi->interval = csi2->frame_interval;
+
+	csi2->frame_interval = fi->interval;
+
+	mutex_unlock(&csi2->lock);
+	return 0;
+}
+
 static int csi2_link_validate(struct v4l2_subdev *sd,
 			      struct media_link *link,
 			      struct v4l2_subdev_format *source_fmt,
@@ -535,6 +565,8 @@ static struct v4l2_subdev_core_ops csi2_core_ops = {
 
 static struct v4l2_subdev_video_ops csi2_video_ops = {
 	.s_stream = csi2_s_stream,
+	.g_frame_interval = csi2_g_frame_interval,
+	.s_frame_interval = csi2_s_frame_interval,
 };
 
 static struct v4l2_subdev_pad_ops csi2_pad_ops = {
@@ -603,6 +635,10 @@ static int csi2_probe(struct platform_device *pdev)
 	csi2->sd.entity.function = MEDIA_ENT_F_VID_IF_BRIDGE;
 	csi2->sd.grp_id = IMX_MEDIA_GRP_ID_CSI2;
 
+	/* init default frame interval */
+	csi2->frame_interval.numerator = 1;
+	csi2->frame_interval.denominator = 30;
+
 	ret = csi2_parse_endpoints(csi2);
 	if (ret)
 		return ret;
-- 
2.7.4

[PATCH v5 33/39] media: imx: mipi-csi2: enable setting and getting of frame rates

[Steve Longerbeam]

From: Russell King <rmk+kernel@armlinux.org.uk>

Setting and getting frame rates is part of the negotiation mechanism
between subdevs.  The lack of support means that a frame rate at the
sensor can't be negotiated through the subdev path.

Add support at MIPI CSI2 level for handling this part of the
negotiation.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/imx6-mipi-csi2.c | 36 ++++++++++++++++++++++++++++++
 1 file changed, 36 insertions(+)

diff --git a/drivers/staging/media/imx/imx6-mipi-csi2.c b/drivers/staging/media/imx/imx6-mipi-csi2.c
index 1a71b40..d8f931e 100644
--- a/drivers/staging/media/imx/imx6-mipi-csi2.c
+++ b/drivers/staging/media/imx/imx6-mipi-csi2.c
@@ -49,6 +49,7 @@ struct csi2_dev {
 	struct mutex lock;
 
 	struct v4l2_mbus_framefmt format_mbus;
+	struct v4l2_fract frame_interval;
 
 	int                     power_count;
 	bool                    stream_on;
@@ -487,6 +488,35 @@ static int csi2_set_fmt(struct v4l2_subdev *sd,
 	return ret;
 }
 
+static int csi2_g_frame_interval(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_frame_interval *fi)
+{
+	struct csi2_dev *csi2 = sd_to_dev(sd);
+
+	mutex_lock(&csi2->lock);
+	fi->interval = csi2->frame_interval;
+	mutex_unlock(&csi2->lock);
+
+	return 0;
+}
+
+static int csi2_s_frame_interval(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_frame_interval *fi)
+{
+	struct csi2_dev *csi2 = sd_to_dev(sd);
+
+	mutex_lock(&csi2->lock);
+
+	/* Output pads mirror active input pad, no limits on input pads */
+	if (fi->pad != CSI2_SINK_PAD)
+		fi->interval = csi2->frame_interval;
+
+	csi2->frame_interval = fi->interval;
+
+	mutex_unlock(&csi2->lock);
+	return 0;
+}
+
 static int csi2_link_validate(struct v4l2_subdev *sd,
 			      struct media_link *link,
 			      struct v4l2_subdev_format *source_fmt,
@@ -535,6 +565,8 @@ static struct v4l2_subdev_core_ops csi2_core_ops = {
 
 static struct v4l2_subdev_video_ops csi2_video_ops = {
 	.s_stream = csi2_s_stream,
+	.g_frame_interval = csi2_g_frame_interval,
+	.s_frame_interval = csi2_s_frame_interval,
 };
 
 static struct v4l2_subdev_pad_ops csi2_pad_ops = {
@@ -603,6 +635,10 @@ static int csi2_probe(struct platform_device *pdev)
 	csi2->sd.entity.function = MEDIA_ENT_F_VID_IF_BRIDGE;
 	csi2->sd.grp_id = IMX_MEDIA_GRP_ID_CSI2;
 
+	/* init default frame interval */
+	csi2->frame_interval.numerator = 1;
+	csi2->frame_interval.denominator = 30;
+
 	ret = csi2_parse_endpoints(csi2);
 	if (ret)
 		return ret;
-- 
2.7.4

[PATCH v5 34/39] media: imx: csi: add __csi_get_fmt

[Steve Longerbeam]

Add __csi_get_fmt() and use it to return the correct mbus format
(active or try) in get_fmt. Use it in other places as well.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Suggested-by: Russell King <linux@armlinux.org.uk>
---
 drivers/staging/media/imx/imx-media-csi.c | 61 ++++++++++++++++++++++++-------
 1 file changed, 47 insertions(+), 14 deletions(-)

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index 577038e..6640869 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -830,13 +830,26 @@ static int csi_eof_isr(struct v4l2_subdev *sd, u32 status, bool *handled)
 	return 0;
 }
 
-static int csi_try_crop(struct csi_priv *priv, struct v4l2_rect *crop,
+static struct v4l2_mbus_framefmt *
+__csi_get_fmt(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
+	      unsigned int pad, enum v4l2_subdev_format_whence which)
+{
+	if (which == V4L2_SUBDEV_FORMAT_TRY)
+		return v4l2_subdev_get_try_format(&priv->sd, cfg, pad);
+	else
+		return &priv->format_mbus[pad];
+}
+
+static int csi_try_crop(struct csi_priv *priv,
+			struct v4l2_rect *crop,
+			struct v4l2_subdev_pad_config *cfg,
+			enum v4l2_subdev_format_whence which,
 			struct imx_media_subdev *sensor)
 {
 	struct v4l2_of_endpoint *sensor_ep;
 	struct v4l2_mbus_framefmt *infmt;
 
-	infmt = &priv->format_mbus[CSI_SINK_PAD];
+	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, which);
 	sensor_ep = &sensor->sensor_ep;
 
 	crop->width = min_t(__u32, infmt->width, crop->width);
@@ -886,17 +899,24 @@ static int csi_get_fmt(struct v4l2_subdev *sd,
 		       struct v4l2_subdev_format *sdformat)
 {
 	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_mbus_framefmt *fmt;
+	int ret = 0;
 
 	if (sdformat->pad >= CSI_NUM_PADS)
 		return -EINVAL;
 
 	mutex_lock(&priv->lock);
 
-	sdformat->format = priv->format_mbus[sdformat->pad];
+	fmt = __csi_get_fmt(priv, cfg, sdformat->pad, sdformat->which);
+	if (!fmt) {
+		ret = -EINVAL;
+		goto out;
+	}
 
+	sdformat->format = *fmt;
+out:
 	mutex_unlock(&priv->lock);
-
-	return 0;
+	return ret;
 }
 
 static int csi_set_fmt(struct v4l2_subdev *sd,
@@ -927,8 +947,6 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 		goto out;
 	}
 
-	infmt = &priv->format_mbus[CSI_SINK_PAD];
-
 	v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
 			      W_ALIGN, &sdformat->format.height,
 			      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
@@ -936,6 +954,8 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 	switch (sdformat->pad) {
 	case CSI_SRC_PAD_DIRECT:
 	case CSI_SRC_PAD_IDMAC:
+		infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sdformat->which);
+
 		if (sdformat->format.width < priv->crop.width * 3 / 4)
 			sdformat->format.width = priv->crop.width / 2;
 		else
@@ -994,7 +1014,8 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 		crop.top = 0;
 		crop.width = sdformat->format.width;
 		crop.height = sdformat->format.height;
-		ret = csi_try_crop(priv, &crop, sensor);
+		ret = csi_try_crop(priv, &crop, cfg,
+				   sdformat->which, sensor);
 		if (ret)
 			goto out;
 
@@ -1039,7 +1060,11 @@ static int csi_get_selection(struct v4l2_subdev *sd,
 
 	mutex_lock(&priv->lock);
 
-	infmt = &priv->format_mbus[CSI_SINK_PAD];
+	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
+	if (!infmt) {
+		ret = -EINVAL;
+		goto out;
+	}
 
 	switch (sel->target) {
 	case V4L2_SEL_TGT_CROP_BOUNDS:
@@ -1049,12 +1074,20 @@ static int csi_get_selection(struct v4l2_subdev *sd,
 		sel->r.height = infmt->height;
 		break;
 	case V4L2_SEL_TGT_CROP:
-		sel->r = priv->crop;
+		if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
+			struct v4l2_rect *try_crop =
+				v4l2_subdev_get_try_crop(&priv->sd,
+							 cfg, sel->pad);
+			sel->r = *try_crop;
+		} else {
+			sel->r = priv->crop;
+		}
 		break;
 	default:
 		ret = -EINVAL;
 	}
 
+out:
 	mutex_unlock(&priv->lock);
 	return ret;
 }
@@ -1064,7 +1097,6 @@ static int csi_set_selection(struct v4l2_subdev *sd,
 			     struct v4l2_subdev_selection *sel)
 {
 	struct csi_priv *priv = v4l2_get_subdevdata(sd);
-	struct v4l2_mbus_framefmt *outfmt;
 	struct imx_media_subdev *sensor;
 	int ret = 0;
 
@@ -1098,15 +1130,16 @@ static int csi_set_selection(struct v4l2_subdev *sd,
 		goto out;
 	}
 
-	outfmt = &priv->format_mbus[sel->pad];
-
-	ret = csi_try_crop(priv, &sel->r, sensor);
+	ret = csi_try_crop(priv, &sel->r, cfg, sel->which, sensor);
 	if (ret)
 		goto out;
 
 	if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
 		cfg->try_crop = sel->r;
 	} else {
+		struct v4l2_mbus_framefmt *outfmt =
+			&priv->format_mbus[sel->pad];
+
 		priv->crop = sel->r;
 		/* Update the source format */
 		outfmt->width = sel->r.width;
-- 
2.7.4

[PATCH v5 34/39] media: imx: csi: add __csi_get_fmt

[Steve Longerbeam]

Add __csi_get_fmt() and use it to return the correct mbus format
(active or try) in get_fmt. Use it in other places as well.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Suggested-by: Russell King <linux@armlinux.org.uk>
---
 drivers/staging/media/imx/imx-media-csi.c | 61 ++++++++++++++++++++++++-------
 1 file changed, 47 insertions(+), 14 deletions(-)

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index 577038e..6640869 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -830,13 +830,26 @@ static int csi_eof_isr(struct v4l2_subdev *sd, u32 status, bool *handled)
 	return 0;
 }
 
-static int csi_try_crop(struct csi_priv *priv, struct v4l2_rect *crop,
+static struct v4l2_mbus_framefmt *
+__csi_get_fmt(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
+	      unsigned int pad, enum v4l2_subdev_format_whence which)
+{
+	if (which == V4L2_SUBDEV_FORMAT_TRY)
+		return v4l2_subdev_get_try_format(&priv->sd, cfg, pad);
+	else
+		return &priv->format_mbus[pad];
+}
+
+static int csi_try_crop(struct csi_priv *priv,
+			struct v4l2_rect *crop,
+			struct v4l2_subdev_pad_config *cfg,
+			enum v4l2_subdev_format_whence which,
 			struct imx_media_subdev *sensor)
 {
 	struct v4l2_of_endpoint *sensor_ep;
 	struct v4l2_mbus_framefmt *infmt;
 
-	infmt = &priv->format_mbus[CSI_SINK_PAD];
+	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, which);
 	sensor_ep = &sensor->sensor_ep;
 
 	crop->width = min_t(__u32, infmt->width, crop->width);
@@ -886,17 +899,24 @@ static int csi_get_fmt(struct v4l2_subdev *sd,
 		       struct v4l2_subdev_format *sdformat)
 {
 	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_mbus_framefmt *fmt;
+	int ret = 0;
 
 	if (sdformat->pad >= CSI_NUM_PADS)
 		return -EINVAL;
 
 	mutex_lock(&priv->lock);
 
-	sdformat->format = priv->format_mbus[sdformat->pad];
+	fmt = __csi_get_fmt(priv, cfg, sdformat->pad, sdformat->which);
+	if (!fmt) {
+		ret = -EINVAL;
+		goto out;
+	}
 
+	sdformat->format = *fmt;
+out:
 	mutex_unlock(&priv->lock);
-
-	return 0;
+	return ret;
 }
 
 static int csi_set_fmt(struct v4l2_subdev *sd,
@@ -927,8 +947,6 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 		goto out;
 	}
 
-	infmt = &priv->format_mbus[CSI_SINK_PAD];
-
 	v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
 			      W_ALIGN, &sdformat->format.height,
 			      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
@@ -936,6 +954,8 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 	switch (sdformat->pad) {
 	case CSI_SRC_PAD_DIRECT:
 	case CSI_SRC_PAD_IDMAC:
+		infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sdformat->which);
+
 		if (sdformat->format.width < priv->crop.width * 3 / 4)
 			sdformat->format.width = priv->crop.width / 2;
 		else
@@ -994,7 +1014,8 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 		crop.top = 0;
 		crop.width = sdformat->format.width;
 		crop.height = sdformat->format.height;
-		ret = csi_try_crop(priv, &crop, sensor);
+		ret = csi_try_crop(priv, &crop, cfg,
+				   sdformat->which, sensor);
 		if (ret)
 			goto out;
 
@@ -1039,7 +1060,11 @@ static int csi_get_selection(struct v4l2_subdev *sd,
 
 	mutex_lock(&priv->lock);
 
-	infmt = &priv->format_mbus[CSI_SINK_PAD];
+	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
+	if (!infmt) {
+		ret = -EINVAL;
+		goto out;
+	}
 
 	switch (sel->target) {
 	case V4L2_SEL_TGT_CROP_BOUNDS:
@@ -1049,12 +1074,20 @@ static int csi_get_selection(struct v4l2_subdev *sd,
 		sel->r.height = infmt->height;
 		break;
 	case V4L2_SEL_TGT_CROP:
-		sel->r = priv->crop;
+		if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
+			struct v4l2_rect *try_crop =
+				v4l2_subdev_get_try_crop(&priv->sd,
+							 cfg, sel->pad);
+			sel->r = *try_crop;
+		} else {
+			sel->r = priv->crop;
+		}
 		break;
 	default:
 		ret = -EINVAL;
 	}
 
+out:
 	mutex_unlock(&priv->lock);
 	return ret;
 }
@@ -1064,7 +1097,6 @@ static int csi_set_selection(struct v4l2_subdev *sd,
 			     struct v4l2_subdev_selection *sel)
 {
 	struct csi_priv *priv = v4l2_get_subdevdata(sd);
-	struct v4l2_mbus_framefmt *outfmt;
 	struct imx_media_subdev *sensor;
 	int ret = 0;
 
@@ -1098,15 +1130,16 @@ static int csi_set_selection(struct v4l2_subdev *sd,
 		goto out;
 	}
 
-	outfmt = &priv->format_mbus[sel->pad];
-
-	ret = csi_try_crop(priv, &sel->r, sensor);
+	ret = csi_try_crop(priv, &sel->r, cfg, sel->which, sensor);
 	if (ret)
 		goto out;
 
 	if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
 		cfg->try_crop = sel->r;
 	} else {
+		struct v4l2_mbus_framefmt *outfmt =
+			&priv->format_mbus[sel->pad];
+
 		priv->crop = sel->r;
 		/* Update the source format */
 		outfmt->width = sel->r.width;
-- 
2.7.4

[PATCH v5 35/39] media: imx: csi/fim: add support for frame intervals

[Steve Longerbeam]

From: Russell King <rmk+kernel@armlinux.org.uk>

Add support to CSI for negotiation of frame intervals, and use this
information to configure the frame interval monitor.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/imx-media-csi.c | 46 +++++++++++++++++++++++++++++--
 drivers/staging/media/imx/imx-media-fim.c | 28 +++++++------------
 drivers/staging/media/imx/imx-media.h     |  2 +-
 3 files changed, 54 insertions(+), 22 deletions(-)

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index 6640869..b556fa4 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -63,6 +63,7 @@ struct csi_priv {
 
 	struct v4l2_mbus_framefmt format_mbus[CSI_NUM_PADS];
 	const struct imx_media_pixfmt *cc[CSI_NUM_PADS];
+	struct v4l2_fract frame_interval;
 	struct v4l2_rect crop;
 
 	/* active vb2 buffers to send to video dev sink */
@@ -570,7 +571,8 @@ static int csi_start(struct csi_priv *priv)
 
 	/* start the frame interval monitor */
 	if (priv->fim) {
-		ret = imx_media_fim_set_stream(priv->fim, priv->sensor, true);
+		ret = imx_media_fim_set_stream(priv->fim,
+					       &priv->frame_interval, true);
 		if (ret)
 			goto idmac_stop;
 	}
@@ -585,7 +587,8 @@ static int csi_start(struct csi_priv *priv)
 
 fim_off:
 	if (priv->fim)
-		imx_media_fim_set_stream(priv->fim, priv->sensor, false);
+		imx_media_fim_set_stream(priv->fim,
+					 &priv->frame_interval, false);
 idmac_stop:
 	if (priv->dest == IPU_CSI_DEST_IDMAC)
 		csi_idmac_stop(priv);
@@ -599,7 +602,8 @@ static void csi_stop(struct csi_priv *priv)
 
 	/* stop the frame interval monitor */
 	if (priv->fim)
-		imx_media_fim_set_stream(priv->fim, priv->sensor, false);
+		imx_media_fim_set_stream(priv->fim,
+					 &priv->frame_interval, false);
 
 	ipu_csi_disable(priv->csi);
 }
@@ -608,6 +612,36 @@ static void csi_stop(struct csi_priv *priv)
  * V4L2 subdev operations.
  */
 
+static int csi_g_frame_interval(struct v4l2_subdev *sd,
+				struct v4l2_subdev_frame_interval *fi)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+
+	mutex_lock(&priv->lock);
+	fi->interval = priv->frame_interval;
+	mutex_unlock(&priv->lock);
+
+	return 0;
+}
+
+static int csi_s_frame_interval(struct v4l2_subdev *sd,
+				struct v4l2_subdev_frame_interval *fi)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+
+	mutex_lock(&priv->lock);
+
+	/* Output pads mirror active input pad, no limits on input pads */
+	if (fi->pad == CSI_SRC_PAD_IDMAC || fi->pad == CSI_SRC_PAD_DIRECT)
+		fi->interval = priv->frame_interval;
+
+	priv->frame_interval = fi->interval;
+
+	mutex_unlock(&priv->lock);
+
+	return 0;
+}
+
 static int csi_s_stream(struct v4l2_subdev *sd, int enable)
 {
 	struct csi_priv *priv = v4l2_get_subdevdata(sd);
@@ -1204,6 +1238,10 @@ static int csi_registered(struct v4l2_subdev *sd)
 			goto put_csi;
 	}
 
+	/* init default frame interval */
+	priv->frame_interval.numerator = 1;
+	priv->frame_interval.denominator = 30;
+
 	priv->fim = imx_media_fim_init(&priv->sd);
 	if (IS_ERR(priv->fim)) {
 		ret = PTR_ERR(priv->fim);
@@ -1254,6 +1292,8 @@ static struct v4l2_subdev_core_ops csi_core_ops = {
 };
 
 static struct v4l2_subdev_video_ops csi_video_ops = {
+	.g_frame_interval = csi_g_frame_interval,
+	.s_frame_interval = csi_s_frame_interval,
 	.s_stream = csi_s_stream,
 };
 
diff --git a/drivers/staging/media/imx/imx-media-fim.c b/drivers/staging/media/imx/imx-media-fim.c
index 824d257..4fe5ffc 100644
--- a/drivers/staging/media/imx/imx-media-fim.c
+++ b/drivers/staging/media/imx/imx-media-fim.c
@@ -67,26 +67,18 @@ struct imx_media_fim {
 };
 
 static void update_fim_nominal(struct imx_media_fim *fim,
-			       struct imx_media_subdev *sensor)
+			       const struct v4l2_fract *fi)
 {
-	struct v4l2_streamparm parm;
-	struct v4l2_fract tpf;
-	int ret;
-
-	parm.type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
-	ret = v4l2_subdev_call(sensor->sd, video, g_parm, &parm);
-	tpf = parm.parm.capture.timeperframe;
-
-	if (ret || tpf.denominator == 0) {
-		dev_dbg(fim->sd->dev, "no tpf from sensor, FIM disabled\n");
+	if (fi->denominator == 0) {
+		dev_dbg(fim->sd->dev, "no frame interval, FIM disabled\n");
 		fim->enabled = false;
 		return;
 	}
 
-	fim->nominal = DIV_ROUND_CLOSEST(1000 * 1000 * tpf.numerator,
-					 tpf.denominator);
+	fim->nominal = DIV_ROUND_CLOSEST_ULL(1000000ULL * (u64)fi->numerator,
+					     fi->denominator);
 
-	dev_dbg(fim->sd->dev, "sensor FI=%lu usec\n", fim->nominal);
+	dev_dbg(fim->sd->dev, "FI=%lu usec\n", fim->nominal);
 }
 
 static void reset_fim(struct imx_media_fim *fim, bool curval)
@@ -130,8 +122,8 @@ static void send_fim_event(struct imx_media_fim *fim, unsigned long error)
 
 /*
  * Monitor an averaged frame interval. If the average deviates too much
- * from the sensor's nominal frame rate, send the frame interval error
- * event. The frame intervals are averaged in order to quiet noise from
+ * from the nominal frame rate, send the frame interval error event. The
+ * frame intervals are averaged in order to quiet noise from
  * (presumably random) interrupt latency.
  */
 static void frame_interval_monitor(struct imx_media_fim *fim,
@@ -422,12 +414,12 @@ EXPORT_SYMBOL_GPL(imx_media_fim_set_power);
 
 /* Called by the subdev in its s_stream callback */
 int imx_media_fim_set_stream(struct imx_media_fim *fim,
-			     struct imx_media_subdev *sensor,
+			     const struct v4l2_fract *fi,
 			     bool on)
 {
 	if (on) {
 		reset_fim(fim, true);
-		update_fim_nominal(fim, sensor);
+		update_fim_nominal(fim, fi);
 
 		if (fim->icap_channel >= 0)
 			fim_acquire_first_ts(fim);
diff --git a/drivers/staging/media/imx/imx-media.h b/drivers/staging/media/imx/imx-media.h
index 9e865fa..a67ee14 100644
--- a/drivers/staging/media/imx/imx-media.h
+++ b/drivers/staging/media/imx/imx-media.h
@@ -262,7 +262,7 @@ struct imx_media_fim;
 void imx_media_fim_eof_monitor(struct imx_media_fim *fim, struct timespec *ts);
 int imx_media_fim_set_power(struct imx_media_fim *fim, bool on);
 int imx_media_fim_set_stream(struct imx_media_fim *fim,
-			     struct imx_media_subdev *sensor,
+			     const struct v4l2_fract *frame_interval,
 			     bool on);
 struct imx_media_fim *imx_media_fim_init(struct v4l2_subdev *sd);
 void imx_media_fim_free(struct imx_media_fim *fim);
-- 
2.7.4

[PATCH v5 35/39] media: imx: csi/fim: add support for frame intervals

[Steve Longerbeam]

From: Russell King <rmk+kernel@armlinux.org.uk>

Add support to CSI for negotiation of frame intervals, and use this
information to configure the frame interval monitor.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/imx-media-csi.c | 46 +++++++++++++++++++++++++++++--
 drivers/staging/media/imx/imx-media-fim.c | 28 +++++++------------
 drivers/staging/media/imx/imx-media.h     |  2 +-
 3 files changed, 54 insertions(+), 22 deletions(-)

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index 6640869..b556fa4 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -63,6 +63,7 @@ struct csi_priv {
 
 	struct v4l2_mbus_framefmt format_mbus[CSI_NUM_PADS];
 	const struct imx_media_pixfmt *cc[CSI_NUM_PADS];
+	struct v4l2_fract frame_interval;
 	struct v4l2_rect crop;
 
 	/* active vb2 buffers to send to video dev sink */
@@ -570,7 +571,8 @@ static int csi_start(struct csi_priv *priv)
 
 	/* start the frame interval monitor */
 	if (priv->fim) {
-		ret = imx_media_fim_set_stream(priv->fim, priv->sensor, true);
+		ret = imx_media_fim_set_stream(priv->fim,
+					       &priv->frame_interval, true);
 		if (ret)
 			goto idmac_stop;
 	}
@@ -585,7 +587,8 @@ static int csi_start(struct csi_priv *priv)
 
 fim_off:
 	if (priv->fim)
-		imx_media_fim_set_stream(priv->fim, priv->sensor, false);
+		imx_media_fim_set_stream(priv->fim,
+					 &priv->frame_interval, false);
 idmac_stop:
 	if (priv->dest == IPU_CSI_DEST_IDMAC)
 		csi_idmac_stop(priv);
@@ -599,7 +602,8 @@ static void csi_stop(struct csi_priv *priv)
 
 	/* stop the frame interval monitor */
 	if (priv->fim)
-		imx_media_fim_set_stream(priv->fim, priv->sensor, false);
+		imx_media_fim_set_stream(priv->fim,
+					 &priv->frame_interval, false);
 
 	ipu_csi_disable(priv->csi);
 }
@@ -608,6 +612,36 @@ static void csi_stop(struct csi_priv *priv)
  * V4L2 subdev operations.
  */
 
+static int csi_g_frame_interval(struct v4l2_subdev *sd,
+				struct v4l2_subdev_frame_interval *fi)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+
+	mutex_lock(&priv->lock);
+	fi->interval = priv->frame_interval;
+	mutex_unlock(&priv->lock);
+
+	return 0;
+}
+
+static int csi_s_frame_interval(struct v4l2_subdev *sd,
+				struct v4l2_subdev_frame_interval *fi)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+
+	mutex_lock(&priv->lock);
+
+	/* Output pads mirror active input pad, no limits on input pads */
+	if (fi->pad == CSI_SRC_PAD_IDMAC || fi->pad == CSI_SRC_PAD_DIRECT)
+		fi->interval = priv->frame_interval;
+
+	priv->frame_interval = fi->interval;
+
+	mutex_unlock(&priv->lock);
+
+	return 0;
+}
+
 static int csi_s_stream(struct v4l2_subdev *sd, int enable)
 {
 	struct csi_priv *priv = v4l2_get_subdevdata(sd);
@@ -1204,6 +1238,10 @@ static int csi_registered(struct v4l2_subdev *sd)
 			goto put_csi;
 	}
 
+	/* init default frame interval */
+	priv->frame_interval.numerator = 1;
+	priv->frame_interval.denominator = 30;
+
 	priv->fim = imx_media_fim_init(&priv->sd);
 	if (IS_ERR(priv->fim)) {
 		ret = PTR_ERR(priv->fim);
@@ -1254,6 +1292,8 @@ static struct v4l2_subdev_core_ops csi_core_ops = {
 };
 
 static struct v4l2_subdev_video_ops csi_video_ops = {
+	.g_frame_interval = csi_g_frame_interval,
+	.s_frame_interval = csi_s_frame_interval,
 	.s_stream = csi_s_stream,
 };
 
diff --git a/drivers/staging/media/imx/imx-media-fim.c b/drivers/staging/media/imx/imx-media-fim.c
index 824d257..4fe5ffc 100644
--- a/drivers/staging/media/imx/imx-media-fim.c
+++ b/drivers/staging/media/imx/imx-media-fim.c
@@ -67,26 +67,18 @@ struct imx_media_fim {
 };
 
 static void update_fim_nominal(struct imx_media_fim *fim,
-			       struct imx_media_subdev *sensor)
+			       const struct v4l2_fract *fi)
 {
-	struct v4l2_streamparm parm;
-	struct v4l2_fract tpf;
-	int ret;
-
-	parm.type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
-	ret = v4l2_subdev_call(sensor->sd, video, g_parm, &parm);
-	tpf = parm.parm.capture.timeperframe;
-
-	if (ret || tpf.denominator == 0) {
-		dev_dbg(fim->sd->dev, "no tpf from sensor, FIM disabled\n");
+	if (fi->denominator == 0) {
+		dev_dbg(fim->sd->dev, "no frame interval, FIM disabled\n");
 		fim->enabled = false;
 		return;
 	}
 
-	fim->nominal = DIV_ROUND_CLOSEST(1000 * 1000 * tpf.numerator,
-					 tpf.denominator);
+	fim->nominal = DIV_ROUND_CLOSEST_ULL(1000000ULL * (u64)fi->numerator,
+					     fi->denominator);
 
-	dev_dbg(fim->sd->dev, "sensor FI=%lu usec\n", fim->nominal);
+	dev_dbg(fim->sd->dev, "FI=%lu usec\n", fim->nominal);
 }
 
 static void reset_fim(struct imx_media_fim *fim, bool curval)
@@ -130,8 +122,8 @@ static void send_fim_event(struct imx_media_fim *fim, unsigned long error)
 
 /*
  * Monitor an averaged frame interval. If the average deviates too much
- * from the sensor's nominal frame rate, send the frame interval error
- * event. The frame intervals are averaged in order to quiet noise from
+ * from the nominal frame rate, send the frame interval error event. The
+ * frame intervals are averaged in order to quiet noise from
  * (presumably random) interrupt latency.
  */
 static void frame_interval_monitor(struct imx_media_fim *fim,
@@ -422,12 +414,12 @@ EXPORT_SYMBOL_GPL(imx_media_fim_set_power);
 
 /* Called by the subdev in its s_stream callback */
 int imx_media_fim_set_stream(struct imx_media_fim *fim,
-			     struct imx_media_subdev *sensor,
+			     const struct v4l2_fract *fi,
 			     bool on)
 {
 	if (on) {
 		reset_fim(fim, true);
-		update_fim_nominal(fim, sensor);
+		update_fim_nominal(fim, fi);
 
 		if (fim->icap_channel >= 0)
 			fim_acquire_first_ts(fim);
diff --git a/drivers/staging/media/imx/imx-media.h b/drivers/staging/media/imx/imx-media.h
index 9e865fa..a67ee14 100644
--- a/drivers/staging/media/imx/imx-media.h
+++ b/drivers/staging/media/imx/imx-media.h
@@ -262,7 +262,7 @@ struct imx_media_fim;
 void imx_media_fim_eof_monitor(struct imx_media_fim *fim, struct timespec *ts);
 int imx_media_fim_set_power(struct imx_media_fim *fim, bool on);
 int imx_media_fim_set_stream(struct imx_media_fim *fim,
-			     struct imx_media_subdev *sensor,
+			     const struct v4l2_fract *frame_interval,
 			     bool on);
 struct imx_media_fim *imx_media_fim_init(struct v4l2_subdev *sd);
 void imx_media_fim_free(struct imx_media_fim *fim);
-- 
2.7.4

[PATCH v5 36/39] media: imx: redo pixel format enumeration and negotiation

[Steve Longerbeam]

The previous API and negotiation of mbus codes and pixel formats
was broken, and has been completely redone.

The negotiation of media bus codes should be as follows:

CSI:

sink pad     direct src pad      IDMAC src pad
--------     ----------------    -------------
RGB (any)        IPU RGB           IPU RGB
YUV (any)        IPU YUV           IPU YUV
Bayer              N/A             must be same bayer code as sink

VDIC:

direct sink pad    IDMAC sink pad    direct src pad
---------------    --------------    --------------
IPU YUV only       IPU YUV only       IPU YUV only

PRP:

direct sink pad    direct src pads
---------------    ---------------
IPU (any)          same as sink code

PRP ENC/VF:

direct sink pad    IDMAC src pads
---------------    --------------
IPU (any)          IPU RGB or IPU YUV

Given the above, a new internal API is created:

enum codespace_sel {
       CS_SEL_YUV = 0, /* find or enumerate only YUV codes */
       CS_SEL_RGB,     /* find or enumerate only RGB codes */
       CS_SEL_ANY,     /* find or enumerate both YUV and RGB codes */
};

/* Find and enumerate fourcc pixel formats */
const struct imx_media_pixfmt *
imx_media_find_format(u32 fourcc, enum codespace_sel cs_sel);
int imx_media_enum_format(u32 *fourcc, u32 index, enum codespace_sel cs_sel);

/* Find and enumerate media bus codes */
const struct imx_media_pixfmt *
imx_media_find_mbus_format(u32 code, enum codespace_sel cs_sel,
                          bool allow_bayer);
int imx_media_enum_mbus_format(u32 *code, u32 index, enum codespace_sel cs_sel,
                              bool allow_bayer);

/* Find and enumerate IPU internal media bus codes */
const struct imx_media_pixfmt *
imx_media_find_ipu_format(u32 code, enum codespace_sel cs_sel);
int imx_media_enum_ipu_format(u32 *code, u32 index, enum codespace_sel cs_sel);

The tables have been split into separate tables for YUV and RGB formats
to support the implementation of the above.

The subdev's .enum_mbus_code() and .set_fmt() operations have
been rewritten using the above APIs.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/imx-ic-prp.c        |  77 ++++--
 drivers/staging/media/imx/imx-ic-prpencvf.c   |  57 ++--
 drivers/staging/media/imx/imx-media-capture.c |  85 ++++--
 drivers/staging/media/imx/imx-media-csi.c     | 108 +++++---
 drivers/staging/media/imx/imx-media-utils.c   | 371 +++++++++++++++++++-------
 drivers/staging/media/imx/imx-media-vdic.c    |  69 ++---
 drivers/staging/media/imx/imx-media.h         |  27 +-
 7 files changed, 504 insertions(+), 290 deletions(-)

diff --git a/drivers/staging/media/imx/imx-ic-prp.c b/drivers/staging/media/imx/imx-ic-prp.c
index 1832915..83cd2b4 100644
--- a/drivers/staging/media/imx/imx-ic-prp.c
+++ b/drivers/staging/media/imx/imx-ic-prp.c
@@ -89,16 +89,6 @@ static void prp_stop(struct prp_priv *priv)
 {
 }
 
-static int prp_enum_mbus_code(struct v4l2_subdev *sd,
-			      struct v4l2_subdev_pad_config *cfg,
-			      struct v4l2_subdev_mbus_code_enum *code)
-{
-	if (code->pad >= PRP_NUM_PADS)
-		return -EINVAL;
-
-	return imx_media_enum_ipu_format(NULL, &code->code, code->index, true);
-}
-
 static struct v4l2_mbus_framefmt *
 __prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_pad_config *cfg,
 	      unsigned int pad, enum v4l2_subdev_format_whence which)
@@ -115,6 +105,38 @@ __prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_pad_config *cfg,
  * V4L2 subdev operations.
  */
 
+static int prp_enum_mbus_code(struct v4l2_subdev *sd,
+			      struct v4l2_subdev_pad_config *cfg,
+			      struct v4l2_subdev_mbus_code_enum *code)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+	struct v4l2_mbus_framefmt *infmt;
+	int ret = 0;
+
+	mutex_lock(&priv->lock);
+
+	switch (code->pad) {
+	case PRP_SINK_PAD:
+		ret = imx_media_enum_ipu_format(&code->code, code->index,
+						CS_SEL_ANY);
+		break;
+	case PRP_SRC_PAD_PRPENC:
+	case PRP_SRC_PAD_PRPVF:
+		if (code->index != 0) {
+			ret = -EINVAL;
+			goto out;
+		}
+		infmt = __prp_get_fmt(priv, cfg, PRP_SINK_PAD, code->which);
+		code->code = infmt->code;
+		break;
+	default:
+		ret = -EINVAL;
+	}
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
 static int prp_get_fmt(struct v4l2_subdev *sd,
 		       struct v4l2_subdev_pad_config *cfg,
 		       struct v4l2_subdev_format *sdformat)
@@ -160,23 +182,28 @@ static int prp_set_fmt(struct v4l2_subdev *sd,
 		goto out;
 	}
 
-	cc = imx_media_find_ipu_format(0, sdformat->format.code, true);
-	if (!cc) {
-		imx_media_enum_ipu_format(NULL, &code, 0, true);
-		cc = imx_media_find_ipu_format(0, code, true);
-		sdformat->format.code = cc->codes[0];
-	}
-
-	v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
-			      W_ALIGN, &sdformat->format.height,
-			      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
-
-	/* Output pads mirror input pad */
-	if (sdformat->pad == PRP_SRC_PAD_PRPENC ||
-	    sdformat->pad == PRP_SRC_PAD_PRPVF) {
+	switch (sdformat->pad) {
+	case PRP_SINK_PAD:
+		v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
+				      W_ALIGN, &sdformat->format.height,
+				      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
+
+		cc = imx_media_find_ipu_format(sdformat->format.code,
+					       CS_SEL_ANY);
+		if (!cc) {
+			imx_media_enum_ipu_format(&code, 0, CS_SEL_ANY);
+			cc = imx_media_find_ipu_format(code, CS_SEL_ANY);
+			sdformat->format.code = cc->codes[0];
+		}
+		break;
+	case PRP_SRC_PAD_PRPENC:
+	case PRP_SRC_PAD_PRPVF:
+		/* Output pads mirror input pad */
 		infmt = __prp_get_fmt(priv, cfg, PRP_SINK_PAD,
 				      sdformat->which);
+		cc = imx_media_find_ipu_format(infmt->code, CS_SEL_ANY);
 		sdformat->format = *infmt;
+		break;
 	}
 
 	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
@@ -402,7 +429,7 @@ static int prp_registered(struct v4l2_subdev *sd)
 			MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
 
 		/* set a default mbus format  */
-		imx_media_enum_ipu_format(NULL, &code, 0, true);
+		imx_media_enum_ipu_format(&code, 0, CS_SEL_YUV);
 		ret = imx_media_init_mbus_fmt(&priv->format_mbus[i],
 					      640, 480, code, V4L2_FIELD_NONE,
 					      &priv->cc[i]);
diff --git a/drivers/staging/media/imx/imx-ic-prpencvf.c b/drivers/staging/media/imx/imx-ic-prpencvf.c
index bd89e9b..b42103c 100644
--- a/drivers/staging/media/imx/imx-ic-prpencvf.c
+++ b/drivers/staging/media/imx/imx-ic-prpencvf.c
@@ -702,20 +702,6 @@ static void prp_stop(struct prp_priv *priv)
 	prp_put_ipu_resources(priv);
 }
 
-static int prp_enum_mbus_code(struct v4l2_subdev *sd,
-			      struct v4l2_subdev_pad_config *cfg,
-			      struct v4l2_subdev_mbus_code_enum *code)
-{
-	if (code->pad >= PRPENCVF_NUM_PADS)
-		return -EINVAL;
-
-	if (code->pad == PRPENCVF_SRC_PAD)
-		return imx_media_enum_format(NULL, &code->code, code->index,
-					     true, false);
-
-	return imx_media_enum_ipu_format(NULL, &code->code, code->index, true);
-}
-
 static struct v4l2_mbus_framefmt *
 __prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_pad_config *cfg,
 	      unsigned int pad, enum v4l2_subdev_format_whence which)
@@ -732,6 +718,16 @@ __prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_pad_config *cfg,
  * V4L2 subdev operations.
  */
 
+static int prp_enum_mbus_code(struct v4l2_subdev *sd,
+			      struct v4l2_subdev_pad_config *cfg,
+			      struct v4l2_subdev_mbus_code_enum *code)
+{
+	if (code->pad >= PRPENCVF_NUM_PADS)
+		return -EINVAL;
+
+	return imx_media_enum_ipu_format(&code->code, code->index, CS_SEL_ANY);
+}
+
 static int prp_get_fmt(struct v4l2_subdev *sd,
 		       struct v4l2_subdev_pad_config *cfg,
 		       struct v4l2_subdev_format *sdformat)
@@ -777,18 +773,17 @@ static int prp_set_fmt(struct v4l2_subdev *sd,
 		goto out;
 	}
 
+	cc = imx_media_find_ipu_format(sdformat->format.code, CS_SEL_ANY);
+	if (!cc) {
+		imx_media_enum_ipu_format(&code, 0, CS_SEL_ANY);
+		cc = imx_media_find_ipu_format(code, CS_SEL_ANY);
+		sdformat->format.code = cc->codes[0];
+	}
+
 	if (sdformat->pad == PRPENCVF_SRC_PAD) {
 		infmt = __prp_get_fmt(priv, cfg, PRPENCVF_SINK_PAD,
 				      sdformat->which);
 
-		cc = imx_media_find_format(0, sdformat->format.code,
-					   true, false);
-		if (!cc) {
-			imx_media_enum_format(NULL, &code, 0, true, false);
-			cc = imx_media_find_format(0, code, true, false);
-			sdformat->format.code = cc->codes[0];
-		}
-
 		if (sdformat->format.field != V4L2_FIELD_NONE)
 			sdformat->format.field = infmt->field;
 
@@ -808,14 +803,6 @@ static int prp_set_fmt(struct v4l2_subdev *sd,
 					      infmt->height / 4, MAX_H_SRC,
 					      H_ALIGN_SRC, S_ALIGN);
 	} else {
-		cc = imx_media_find_ipu_format(0, sdformat->format.code,
-					       true);
-		if (!cc) {
-			imx_media_enum_ipu_format(NULL, &code, 0, true);
-			cc = imx_media_find_ipu_format(0, code, true);
-			sdformat->format.code = cc->codes[0];
-		}
-
 		v4l_bound_align_image(&sdformat->format.width,
 				      MIN_W_SINK, MAX_W_SINK, W_ALIGN_SINK,
 				      &sdformat->format.height,
@@ -1098,15 +1085,11 @@ static int prp_registered(struct v4l2_subdev *sd)
 	priv->md = dev_get_drvdata(sd->v4l2_dev->dev);
 
 	for (i = 0; i < PRPENCVF_NUM_PADS; i++) {
-		if (i == PRPENCVF_SINK_PAD) {
-			priv->pad[i].flags = MEDIA_PAD_FL_SINK;
-			imx_media_enum_ipu_format(NULL, &code, 0, true);
-		} else {
-			priv->pad[i].flags = MEDIA_PAD_FL_SOURCE;
-			code = 0;
-		}
+		priv->pad[i].flags = (i == PRPENCVF_SINK_PAD) ?
+			MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
 
 		/* set a default mbus format  */
+		imx_media_enum_ipu_format(&code, 0, CS_SEL_YUV);
 		ret = imx_media_init_mbus_fmt(&priv->format_mbus[i],
 					      640, 480, code, V4L2_FIELD_NONE,
 					      &priv->cc[i]);
diff --git a/drivers/staging/media/imx/imx-media-capture.c b/drivers/staging/media/imx/imx-media-capture.c
index 704ed85..a757e05 100644
--- a/drivers/staging/media/imx/imx-media-capture.c
+++ b/drivers/staging/media/imx/imx-media-capture.c
@@ -85,12 +85,39 @@ static int vidioc_querycap(struct file *file, void *fh,
 static int capture_enum_fmt_vid_cap(struct file *file, void *fh,
 				    struct v4l2_fmtdesc *f)
 {
+	struct capture_priv *priv = video_drvdata(file);
+	const struct imx_media_pixfmt *cc_src;
+	struct v4l2_subdev_format fmt_src;
 	u32 fourcc;
 	int ret;
 
-	ret = imx_media_enum_format(&fourcc, NULL, f->index, true, true);
-	if (ret)
+	fmt_src.pad = priv->src_sd_pad;
+	fmt_src.which = V4L2_SUBDEV_FORMAT_ACTIVE;
+	ret = v4l2_subdev_call(priv->src_sd, pad, get_fmt, NULL, &fmt_src);
+	if (ret) {
+		v4l2_err(priv->src_sd, "failed to get src_sd format\n");
 		return ret;
+	}
+
+	cc_src = imx_media_find_ipu_format(fmt_src.format.code, CS_SEL_ANY);
+	if (!cc_src)
+		cc_src = imx_media_find_mbus_format(fmt_src.format.code,
+						    CS_SEL_ANY, true);
+	if (!cc_src)
+		return -EINVAL;
+
+	if (cc_src->bayer) {
+		if (f->index != 0)
+			return -EINVAL;
+		fourcc = cc_src->fourcc;
+	} else {
+		u32 cs_sel = (cc_src->cs == IPUV3_COLORSPACE_YUV) ?
+			CS_SEL_YUV : CS_SEL_RGB;
+
+		ret = imx_media_enum_format(&fourcc, f->index, cs_sel);
+		if (ret)
+			return ret;
+	}
 
 	f->pixelformat = fourcc;
 
@@ -112,40 +139,40 @@ static int capture_try_fmt_vid_cap(struct file *file, void *fh,
 {
 	struct capture_priv *priv = video_drvdata(file);
 	struct v4l2_subdev_format fmt_src;
-	const struct imx_media_pixfmt *cc, *src_cc;
-	u32 fourcc;
+	const struct imx_media_pixfmt *cc, *cc_src;
 	int ret;
 
-	fourcc = f->fmt.pix.pixelformat;
-	cc = imx_media_find_format(fourcc, 0, true, true);
-	if (!cc) {
-		imx_media_enum_format(&fourcc, NULL, 0, true, true);
-		cc = imx_media_find_format(fourcc, 0, true, true);
-	}
-
-	/*
-	 * user frame dimensions are the same as src_sd's pad.
-	 */
 	fmt_src.pad = priv->src_sd_pad;
 	fmt_src.which = V4L2_SUBDEV_FORMAT_ACTIVE;
 	ret = v4l2_subdev_call(priv->src_sd, pad, get_fmt, NULL, &fmt_src);
 	if (ret)
 		return ret;
 
-	/*
-	 * but we can allow planar pixel formats if the src_sd's
-	 * pad configured a YUV format
-	 */
-	src_cc = imx_media_find_format(0, fmt_src.format.code, true, false);
-	if (src_cc->cs == IPUV3_COLORSPACE_YUV &&
-	    cc->cs == IPUV3_COLORSPACE_YUV) {
-		imx_media_mbus_fmt_to_pix_fmt(&f->fmt.pix,
-					      &fmt_src.format, cc);
+	cc_src = imx_media_find_ipu_format(fmt_src.format.code, CS_SEL_ANY);
+	if (!cc_src)
+		cc_src = imx_media_find_mbus_format(fmt_src.format.code,
+						    CS_SEL_ANY, true);
+	if (!cc_src)
+		return -EINVAL;
+
+	if (cc_src->bayer) {
+		cc = cc_src;
 	} else {
-		imx_media_mbus_fmt_to_pix_fmt(&f->fmt.pix,
-					      &fmt_src.format, src_cc);
+		u32 fourcc, cs_sel;
+
+		cs_sel = (cc_src->cs == IPUV3_COLORSPACE_YUV) ?
+			CS_SEL_YUV : CS_SEL_RGB;
+		fourcc = f->fmt.pix.pixelformat;
+
+		cc = imx_media_find_format(fourcc, cs_sel);
+		if (!cc) {
+			imx_media_enum_format(&fourcc, 0, cs_sel);
+			cc = imx_media_find_format(fourcc, cs_sel);
+		}
 	}
 
+	imx_media_mbus_fmt_to_pix_fmt(&f->fmt.pix, &fmt_src.format, cc);
+
 	return 0;
 }
 
@@ -165,8 +192,8 @@ static int capture_s_fmt_vid_cap(struct file *file, void *fh,
 		return ret;
 
 	priv->vdev.fmt.fmt.pix = f->fmt.pix;
-	priv->vdev.cc = imx_media_find_format(f->fmt.pix.pixelformat, 0,
-					      true, true);
+	priv->vdev.cc = imx_media_find_format(f->fmt.pix.pixelformat,
+					      CS_SEL_ANY);
 
 	return 0;
 }
@@ -574,8 +601,8 @@ int imx_media_capture_device_register(struct imx_media_video_dev *vdev)
 	vdev->fmt.type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
 	imx_media_mbus_fmt_to_pix_fmt(&vdev->fmt.fmt.pix,
 				      &fmt_src.format, NULL);
-	vdev->cc = imx_media_find_format(0, fmt_src.format.code,
-					 true, false);
+	vdev->cc = imx_media_find_format(vdev->fmt.fmt.pix.pixelformat,
+					 CS_SEL_ANY);
 
 	v4l2_info(sd, "Registered %s as /dev/%s\n", vfd->name,
 		  video_device_node_name(vfd));
diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index b556fa4..a726744 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -917,15 +917,44 @@ static int csi_enum_mbus_code(struct v4l2_subdev *sd,
 			      struct v4l2_subdev_pad_config *cfg,
 			      struct v4l2_subdev_mbus_code_enum *code)
 {
-	if (code->pad >= CSI_NUM_PADS)
-		return -EINVAL;
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	const struct imx_media_pixfmt *incc;
+	struct v4l2_mbus_framefmt *infmt;
+	int ret = 0;
 
-	if (code->pad == CSI_SRC_PAD_DIRECT)
-		return imx_media_enum_ipu_format(NULL, &code->code,
-						 code->index, true);
+	mutex_lock(&priv->lock);
+
+	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, code->which);
+	incc = imx_media_find_mbus_format(infmt->code, CS_SEL_ANY, true);
 
-	return imx_media_enum_format(NULL, &code->code, code->index,
-				     true, false);
+	switch (code->pad) {
+	case CSI_SINK_PAD:
+		ret = imx_media_enum_mbus_format(&code->code, code->index,
+						 CS_SEL_ANY, true);
+		break;
+	case CSI_SRC_PAD_DIRECT:
+	case CSI_SRC_PAD_IDMAC:
+		if (incc->bayer) {
+			if (code->index != 0) {
+				ret = -EINVAL;
+				goto out;
+			}
+			code->code = infmt->code;
+		} else {
+			u32 cs_sel = (incc->cs == IPUV3_COLORSPACE_YUV) ?
+				CS_SEL_YUV : CS_SEL_RGB;
+			ret = imx_media_enum_ipu_format(&code->code,
+							code->index,
+							cs_sel);
+		}
+		break;
+	default:
+		ret = -EINVAL;
+	}
+
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
 }
 
 static int csi_get_fmt(struct v4l2_subdev *sd,
@@ -981,14 +1010,13 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 		goto out;
 	}
 
-	v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
-			      W_ALIGN, &sdformat->format.height,
-			      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
-
 	switch (sdformat->pad) {
 	case CSI_SRC_PAD_DIRECT:
 	case CSI_SRC_PAD_IDMAC:
-		infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sdformat->which);
+		infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD,
+				      sdformat->which);
+		incc = imx_media_find_mbus_format(infmt->code,
+						  CS_SEL_ANY, true);
 
 		if (sdformat->format.width < priv->crop.width * 3 / 4)
 			sdformat->format.width = priv->crop.width / 2;
@@ -1000,38 +1028,25 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 		else
 			sdformat->format.height = priv->crop.height;
 
-		if (sdformat->pad == CSI_SRC_PAD_IDMAC) {
-			cc = imx_media_find_format(0, sdformat->format.code,
-						   true, false);
-			if (!cc) {
-				imx_media_enum_format(NULL, &code, 0,
-						      true, false);
-				cc = imx_media_find_format(0, code,
-							   true, false);
-				sdformat->format.code = cc->codes[0];
-			}
-
-			incc = priv->cc[CSI_SINK_PAD];
-			if (cc->cs != incc->cs) {
-				sdformat->format.code = infmt->code;
-				cc = imx_media_find_format(
-					0, sdformat->format.code,
-					true, false);
-			}
-
-			if (sdformat->format.field != V4L2_FIELD_NONE)
-				sdformat->format.field = infmt->field;
+		if (incc->bayer) {
+			sdformat->format.code = infmt->code;
+			cc = incc;
 		} else {
-			cc = imx_media_find_ipu_format(0, sdformat->format.code,
-						       true);
+			u32 cs_sel = (incc->cs == IPUV3_COLORSPACE_YUV) ?
+				CS_SEL_YUV : CS_SEL_RGB;
+
+			cc = imx_media_find_ipu_format(sdformat->format.code,
+						       cs_sel);
 			if (!cc) {
-				imx_media_enum_ipu_format(NULL, &code, 0, true);
-				cc = imx_media_find_ipu_format(0, code, true);
+				imx_media_enum_ipu_format(&code, 0, cs_sel);
+				cc = imx_media_find_ipu_format(code, cs_sel);
 				sdformat->format.code = cc->codes[0];
 			}
+		}
 
+		if (sdformat->pad == CSI_SRC_PAD_DIRECT ||
+		    sdformat->format.field != V4L2_FIELD_NONE)
 			sdformat->format.field = infmt->field;
-		}
 
 		/*
 		 * translate V4L2_FIELD_ALTERNATE to SEQ_TB or SEQ_BT
@@ -1044,6 +1059,9 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 		}
 		break;
 	case CSI_SINK_PAD:
+		v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
+				      W_ALIGN, &sdformat->format.height,
+				      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
 		crop.left = 0;
 		crop.top = 0;
 		crop.width = sdformat->format.width;
@@ -1053,11 +1071,13 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 		if (ret)
 			goto out;
 
-		cc = imx_media_find_format(0, sdformat->format.code,
-					   true, false);
+		cc = imx_media_find_mbus_format(sdformat->format.code,
+						CS_SEL_ANY, true);
 		if (!cc) {
-			imx_media_enum_format(NULL, &code, 0, true, false);
-			cc = imx_media_find_format(0, code, true, false);
+			imx_media_enum_mbus_format(&code, 0,
+						   CS_SEL_ANY, false);
+			cc = imx_media_find_mbus_format(code,
+							CS_SEL_ANY, false);
 			sdformat->format.code = cc->codes[0];
 		}
 		break;
@@ -1227,8 +1247,8 @@ static int csi_registered(struct v4l2_subdev *sd)
 			MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
 
 		code = 0;
-		if (i == CSI_SRC_PAD_DIRECT)
-			imx_media_enum_ipu_format(NULL, &code, 0, true);
+		if (i != CSI_SINK_PAD)
+			imx_media_enum_ipu_format(&code, 0, CS_SEL_YUV);
 
 		/* set a default mbus format  */
 		ret = imx_media_init_mbus_fmt(&priv->format_mbus[i],
diff --git a/drivers/staging/media/imx/imx-media-utils.c b/drivers/staging/media/imx/imx-media-utils.c
index 24e3795..a648fd5 100644
--- a/drivers/staging/media/imx/imx-media-utils.c
+++ b/drivers/staging/media/imx/imx-media-utils.c
@@ -12,14 +12,13 @@
 #include "imx-media.h"
 
 /*
- * List of pixel formats for the subdevs. This must be a super-set of
- * the formats supported by the ipu image converter.
+ * List of supported pixel formats for the subdevs.
  *
- * The non-mbus formats (planar and BGR) must all fall at the end of
- * this table, otherwise enum_fmt() at media pads will stop before
- * seeing all the supported mbus formats.
+ * In all of these tables, the non-mbus formats (with no
+ * mbus codes) must all fall at the end of the table.
  */
-static const struct imx_media_pixfmt imx_media_formats[] = {
+
+static const struct imx_media_pixfmt yuv_formats[] = {
 	{
 		.fourcc	= V4L2_PIX_FMT_UYVY,
 		.codes  = {
@@ -36,13 +35,45 @@ static const struct imx_media_pixfmt imx_media_formats[] = {
 		},
 		.cs     = IPUV3_COLORSPACE_YUV,
 		.bpp    = 16,
+	},
+	/***
+	 * non-mbus YUV formats start here. NOTE! when adding non-mbus
+	 * formats, NUM_NON_MBUS_YUV_FORMATS must be updated below.
+	 ***/
+	{
+		.fourcc	= V4L2_PIX_FMT_YUV420,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 12,
+		.planar = true,
 	}, {
-		.fourcc = V4L2_PIX_FMT_YUV32,
-		.codes  = {MEDIA_BUS_FMT_AYUV8_1X32},
+		.fourcc = V4L2_PIX_FMT_YVU420,
 		.cs     = IPUV3_COLORSPACE_YUV,
-		.bpp    = 32,
-		.ipufmt = true,
+		.bpp    = 12,
+		.planar = true,
 	}, {
+		.fourcc = V4L2_PIX_FMT_YUV422P,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 16,
+		.planar = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_NV12,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 12,
+		.planar = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_NV16,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 16,
+		.planar = true,
+	},
+};
+
+#define NUM_NON_MBUS_YUV_FORMATS 5
+#define NUM_YUV_FORMATS ARRAY_SIZE(yuv_formats)
+#define NUM_MBUS_YUV_FORMATS (NUM_YUV_FORMATS - NUM_NON_MBUS_YUV_FORMATS)
+
+static const struct imx_media_pixfmt rgb_formats[] = {
+	{
 		.fourcc	= V4L2_PIX_FMT_RGB565,
 		.codes  = {MEDIA_BUS_FMT_RGB565_2X8_LE},
 		.cs     = IPUV3_COLORSPACE_RGB,
@@ -61,7 +92,9 @@ static const struct imx_media_pixfmt imx_media_formats[] = {
 		.cs     = IPUV3_COLORSPACE_RGB,
 		.bpp    = 32,
 		.ipufmt = true,
-	}, {
+	},
+	/*** raw bayer formats start here ***/
+	{
 		.fourcc = V4L2_PIX_FMT_SBGGR8,
 		.codes  = {MEDIA_BUS_FMT_SBGGR8_1X8},
 		.cs     = IPUV3_COLORSPACE_RGB,
@@ -130,7 +163,10 @@ static const struct imx_media_pixfmt imx_media_formats[] = {
 		.bpp    = 16,
 		.bayer  = true,
 	},
-	/*** non-mbus formats start here ***/
+	/***
+	 * non-mbus RGB formats start here. NOTE! when adding non-mbus
+	 * formats, NUM_NON_MBUS_RGB_FORMATS must be updated below.
+	 ***/
 	{
 		.fourcc	= V4L2_PIX_FMT_BGR24,
 		.cs     = IPUV3_COLORSPACE_RGB,
@@ -139,135 +175,256 @@ static const struct imx_media_pixfmt imx_media_formats[] = {
 		.fourcc	= V4L2_PIX_FMT_BGR32,
 		.cs     = IPUV3_COLORSPACE_RGB,
 		.bpp    = 32,
-	}, {
-		.fourcc	= V4L2_PIX_FMT_YUV420,
-		.cs     = IPUV3_COLORSPACE_YUV,
-		.bpp    = 12,
-		.planar = true,
-	}, {
-		.fourcc = V4L2_PIX_FMT_YVU420,
-		.cs     = IPUV3_COLORSPACE_YUV,
-		.bpp    = 12,
-		.planar = true,
-	}, {
-		.fourcc = V4L2_PIX_FMT_YUV422P,
-		.cs     = IPUV3_COLORSPACE_YUV,
-		.bpp    = 16,
-		.planar = true,
-	}, {
-		.fourcc = V4L2_PIX_FMT_NV12,
-		.cs     = IPUV3_COLORSPACE_YUV,
-		.bpp    = 12,
-		.planar = true,
-	}, {
-		.fourcc = V4L2_PIX_FMT_NV16,
+	},
+};
+
+#define NUM_NON_MBUS_RGB_FORMATS 2
+#define NUM_RGB_FORMATS ARRAY_SIZE(rgb_formats)
+#define NUM_MBUS_RGB_FORMATS (NUM_RGB_FORMATS - NUM_NON_MBUS_RGB_FORMATS)
+
+static const struct imx_media_pixfmt ipu_yuv_formats[] = {
+	{
+		.fourcc = V4L2_PIX_FMT_YUV32,
+		.codes  = {MEDIA_BUS_FMT_AYUV8_1X32},
 		.cs     = IPUV3_COLORSPACE_YUV,
-		.bpp    = 16,
-		.planar = true,
+		.bpp    = 32,
+		.ipufmt = true,
 	},
 };
 
-static const u32 imx_media_ipu_internal_codes[] = {
-	MEDIA_BUS_FMT_AYUV8_1X32, MEDIA_BUS_FMT_ARGB8888_1X32,
+#define NUM_IPU_YUV_FORMATS ARRAY_SIZE(ipu_yuv_formats)
+
+static const struct imx_media_pixfmt ipu_rgb_formats[] = {
+	{
+		.fourcc	= V4L2_PIX_FMT_RGB32,
+		.codes  = {MEDIA_BUS_FMT_ARGB8888_1X32},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 32,
+		.ipufmt = true,
+	},
 };
 
+#define NUM_IPU_RGB_FORMATS ARRAY_SIZE(ipu_rgb_formats)
+
 static inline u32 pixfmt_to_colorspace(const struct imx_media_pixfmt *fmt)
 {
 	return (fmt->cs == IPUV3_COLORSPACE_RGB) ?
 		V4L2_COLORSPACE_SRGB : V4L2_COLORSPACE_SMPTE170M;
 }
 
-static const struct imx_media_pixfmt *find_format(u32 fourcc, u32 code,
-						  bool allow_rgb,
-						  bool allow_planar,
-						  bool ipu_fmt_only)
+static const struct imx_media_pixfmt *find_format(u32 fourcc,
+						  u32 code,
+						  enum codespace_sel cs_sel,
+						  bool allow_non_mbus,
+						  bool allow_bayer)
 {
-	const struct imx_media_pixfmt *fmt, *ret = NULL;
+	const struct imx_media_pixfmt *array, *fmt, *ret = NULL;
+	u32 array_size;
 	int i, j;
 
-	for (i = 0; i < ARRAY_SIZE(imx_media_formats); i++) {
-		fmt = &imx_media_formats[i];
+	switch (cs_sel) {
+	case CS_SEL_YUV:
+		array_size = NUM_YUV_FORMATS;
+		array = yuv_formats;
+		break;
+	case CS_SEL_RGB:
+		array_size = NUM_RGB_FORMATS;
+		array = rgb_formats;
+		break;
+	case CS_SEL_ANY:
+		array_size = NUM_YUV_FORMATS + NUM_RGB_FORMATS;
+		array = yuv_formats;
+		break;
+	default:
+		return NULL;
+	}
+
+	for (i = 0; i < array_size; i++) {
+		if (cs_sel == CS_SEL_ANY && i >= NUM_YUV_FORMATS)
+			fmt = &rgb_formats[i - NUM_YUV_FORMATS];
+		else
+			fmt = &array[i];
 
-		if (ipu_fmt_only && !fmt->ipufmt)
+		if ((!allow_non_mbus && fmt->codes[0] == 0) ||
+		    (!allow_bayer && fmt->bayer))
 			continue;
 
-		if (fourcc && fmt->fourcc == fourcc &&
-		    (fmt->cs != IPUV3_COLORSPACE_RGB || allow_rgb) &&
-		    (!fmt->planar || allow_planar)) {
+		if (fourcc && fmt->fourcc == fourcc) {
 			ret = fmt;
 			goto out;
 		}
 
 		for (j = 0; code && fmt->codes[j]; j++) {
-			if (fmt->codes[j] == code && !fmt->planar &&
-			    (fmt->cs != IPUV3_COLORSPACE_RGB || allow_rgb)) {
+			if (code == fmt->codes[j]) {
 				ret = fmt;
 				goto out;
 			}
 		}
 	}
+
 out:
 	return ret;
 }
 
-const struct imx_media_pixfmt *imx_media_find_format(u32 fourcc, u32 code,
-						     bool allow_rgb,
-						     bool allow_planar)
+static int enum_format(u32 *fourcc, u32 *code, u32 index,
+		       enum codespace_sel cs_sel,
+		       bool allow_non_mbus,
+		       bool allow_bayer)
+{
+	const struct imx_media_pixfmt *fmt;
+	u32 mbus_yuv_sz = NUM_MBUS_YUV_FORMATS;
+	u32 mbus_rgb_sz = NUM_MBUS_RGB_FORMATS;
+	u32 yuv_sz = NUM_YUV_FORMATS;
+	u32 rgb_sz = NUM_RGB_FORMATS;
+
+	switch (cs_sel) {
+	case CS_SEL_YUV:
+		if (index >= yuv_sz ||
+		    (!allow_non_mbus && index >= mbus_yuv_sz))
+			return -EINVAL;
+		fmt = &yuv_formats[index];
+		break;
+	case CS_SEL_RGB:
+		if (index >= rgb_sz ||
+		    (!allow_non_mbus && index >= mbus_rgb_sz))
+			return -EINVAL;
+		fmt = &rgb_formats[index];
+		if (!allow_bayer && fmt->bayer)
+			return -EINVAL;
+		break;
+	case CS_SEL_ANY:
+		if (!allow_non_mbus) {
+			if (index >= mbus_yuv_sz) {
+				index -= mbus_yuv_sz;
+				if (index >= mbus_rgb_sz)
+					return -EINVAL;
+				fmt = &rgb_formats[index];
+				if (!allow_bayer && fmt->bayer)
+					return -EINVAL;
+			} else {
+				fmt = &yuv_formats[index];
+			}
+		} else {
+			if (index >= yuv_sz + rgb_sz)
+				return -EINVAL;
+			if (index >= yuv_sz) {
+				fmt = &rgb_formats[index - yuv_sz];
+				if (!allow_bayer && fmt->bayer)
+					return -EINVAL;
+			} else {
+				fmt = &yuv_formats[index];
+			}
+		}
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	if (fourcc)
+		*fourcc = fmt->fourcc;
+	if (code)
+		*code = fmt->codes[0];
+
+	return 0;
+}
+
+const struct imx_media_pixfmt *
+imx_media_find_format(u32 fourcc, enum codespace_sel cs_sel)
 {
-	return find_format(fourcc, code, allow_rgb, allow_planar, false);
+	return find_format(fourcc, 0, cs_sel, true, false);
 }
 EXPORT_SYMBOL_GPL(imx_media_find_format);
 
-const struct imx_media_pixfmt *imx_media_find_ipu_format(u32 fourcc,
-							 u32 code,
-							 bool allow_rgb)
+int imx_media_enum_format(u32 *fourcc, u32 index, enum codespace_sel cs_sel)
 {
-	return find_format(fourcc, code, allow_rgb, false, true);
+	return enum_format(fourcc, NULL, index, cs_sel, true, false);
 }
-EXPORT_SYMBOL_GPL(imx_media_find_ipu_format);
+EXPORT_SYMBOL_GPL(imx_media_enum_format);
 
-int imx_media_enum_format(u32 *fourcc, u32 *code, u32 index,
-			  bool allow_rgb, bool allow_planar)
+const struct imx_media_pixfmt *
+imx_media_find_mbus_format(u32 code, enum codespace_sel cs_sel,
+			   bool allow_bayer)
 {
-	const struct imx_media_pixfmt *fmt;
+	return find_format(0, code, cs_sel, false, allow_bayer);
+}
+EXPORT_SYMBOL_GPL(imx_media_find_mbus_format);
 
-	if (index >= ARRAY_SIZE(imx_media_formats))
-		return -EINVAL;
+int imx_media_enum_mbus_format(u32 *code, u32 index, enum codespace_sel cs_sel,
+			       bool allow_bayer)
+{
+	return enum_format(NULL, code, index, cs_sel, false, allow_bayer);
+}
+EXPORT_SYMBOL_GPL(imx_media_enum_mbus_format);
 
-	fmt = &imx_media_formats[index];
+const struct imx_media_pixfmt *
+imx_media_find_ipu_format(u32 code, enum codespace_sel cs_sel)
+{
+	const struct imx_media_pixfmt *array, *fmt, *ret = NULL;
+	u32 array_size;
+	int i, j;
 
-	if ((fmt->cs == IPUV3_COLORSPACE_RGB && !allow_rgb) ||
-	    (fmt->planar && !allow_planar))
-		return -EINVAL;
+	switch (cs_sel) {
+	case CS_SEL_YUV:
+		array_size = NUM_IPU_YUV_FORMATS;
+		array = ipu_yuv_formats;
+		break;
+	case CS_SEL_RGB:
+		array_size = NUM_IPU_RGB_FORMATS;
+		array = ipu_rgb_formats;
+		break;
+	case CS_SEL_ANY:
+		array_size = NUM_IPU_YUV_FORMATS + NUM_IPU_RGB_FORMATS;
+		array = ipu_yuv_formats;
+		break;
+	default:
+		return NULL;
+	}
 
-	if (code)
-		*code = fmt->codes[0];
-	if (fourcc)
-		*fourcc = fmt->fourcc;
+	for (i = 0; i < array_size; i++) {
+		if (cs_sel == CS_SEL_ANY && i >= NUM_IPU_YUV_FORMATS)
+			fmt = &ipu_rgb_formats[i - NUM_IPU_YUV_FORMATS];
+		else
+			fmt = &array[i];
 
-	return 0;
+		for (j = 0; code && fmt->codes[j]; j++) {
+			if (code == fmt->codes[j]) {
+				ret = fmt;
+				goto out;
+			}
+		}
+	}
+
+out:
+	return ret;
 }
-EXPORT_SYMBOL_GPL(imx_media_enum_format);
+EXPORT_SYMBOL_GPL(imx_media_find_ipu_format);
 
-int imx_media_enum_ipu_format(u32 *fourcc, u32 *code, u32 index,
-			      bool allow_rgb)
+int imx_media_enum_ipu_format(u32 *code, u32 index, enum codespace_sel cs_sel)
 {
-	const struct imx_media_pixfmt *fmt;
-	u32 lcode;
-
-	if (index >= ARRAY_SIZE(imx_media_ipu_internal_codes))
-		return -EINVAL;
-
-	lcode = imx_media_ipu_internal_codes[index];
-
-	fmt = find_format(0, lcode, allow_rgb, false, true);
-	if (!fmt)
+	switch (cs_sel) {
+	case CS_SEL_YUV:
+		if (index >= NUM_IPU_YUV_FORMATS)
+			return -EINVAL;
+		*code = ipu_yuv_formats[index].codes[0];
+		break;
+	case CS_SEL_RGB:
+		if (index >= NUM_IPU_RGB_FORMATS)
+			return -EINVAL;
+		*code = ipu_rgb_formats[index].codes[0];
+		break;
+	case CS_SEL_ANY:
+		if (index >= NUM_IPU_YUV_FORMATS + NUM_IPU_RGB_FORMATS)
+			return -EINVAL;
+		if (index >= NUM_IPU_YUV_FORMATS) {
+			index -= NUM_IPU_YUV_FORMATS;
+			*code = ipu_rgb_formats[index].codes[0];
+		} else {
+			*code = ipu_yuv_formats[index].codes[0];
+		}
+		break;
+	default:
 		return -EINVAL;
-
-	if (code)
-		*code = fmt->codes[0];
-	if (fourcc)
-		*fourcc = fmt->fourcc;
+	}
 
 	return 0;
 }
@@ -283,10 +440,14 @@ int imx_media_init_mbus_fmt(struct v4l2_mbus_framefmt *mbus,
 	mbus->height = height;
 	mbus->field = field;
 	if (code == 0)
-		imx_media_enum_format(NULL, &code, 0, true, false);
-	lcc = imx_media_find_format(0, code, true, false);
-	if (!lcc)
-		return -EINVAL;
+		imx_media_enum_mbus_format(&code, 0, CS_SEL_YUV, false);
+	lcc = imx_media_find_mbus_format(code, CS_SEL_ANY, false);
+	if (!lcc) {
+		lcc = imx_media_find_ipu_format(code, CS_SEL_ANY);
+		if (!lcc)
+			return -EINVAL;
+	}
+
 	mbus->code = code;
 	mbus->colorspace = pixfmt_to_colorspace(lcc);
 
@@ -304,11 +465,25 @@ int imx_media_mbus_fmt_to_pix_fmt(struct v4l2_pix_format *pix,
 	u32 stride;
 
 	if (!cc) {
-		cc = imx_media_find_format(0, mbus->code, true, false);
+		cc = imx_media_find_ipu_format(mbus->code, CS_SEL_ANY);
+		if (!cc)
+			cc = imx_media_find_mbus_format(mbus->code, CS_SEL_ANY,
+							true);
 		if (!cc)
 			return -EINVAL;
 	}
 
+	/*
+	 * TODO: the IPU currently does not support the AYUV32 format,
+	 * so until it does convert to a supported YUV format.
+	 */
+	if (cc->ipufmt && cc->cs == IPUV3_COLORSPACE_YUV) {
+		u32 code;
+
+		imx_media_enum_mbus_format(&code, 0, CS_SEL_YUV, false);
+		cc = imx_media_find_mbus_format(code, CS_SEL_YUV, false);
+	}
+
 	stride = cc->planar ? mbus->width : (mbus->width * cc->bpp) >> 3;
 
 	pix->width = mbus->width;
@@ -349,7 +524,7 @@ int imx_media_ipu_image_to_mbus_fmt(struct v4l2_mbus_framefmt *mbus,
 {
 	const struct imx_media_pixfmt *fmt;
 
-	fmt = imx_media_find_format(image->pix.pixelformat, 0, true, false);
+	fmt = imx_media_find_format(image->pix.pixelformat, CS_SEL_ANY);
 	if (!fmt)
 		return -EINVAL;
 
diff --git a/drivers/staging/media/imx/imx-media-vdic.c b/drivers/staging/media/imx/imx-media-vdic.c
index 0e7c24c..070f9da 100644
--- a/drivers/staging/media/imx/imx-media-vdic.c
+++ b/drivers/staging/media/imx/imx-media-vdic.c
@@ -517,20 +517,6 @@ static int vdic_s_stream(struct v4l2_subdev *sd, int enable)
 	return ret;
 }
 
-static int vdic_enum_mbus_code(struct v4l2_subdev *sd,
-			       struct v4l2_subdev_pad_config *cfg,
-			       struct v4l2_subdev_mbus_code_enum *code)
-{
-	if (code->pad >= VDIC_NUM_PADS)
-		return -EINVAL;
-
-	if (code->pad == VDIC_SINK_PAD_IDMAC)
-		return imx_media_enum_format(NULL, &code->code, code->index,
-					     false, false);
-
-	return imx_media_enum_ipu_format(NULL, &code->code, code->index, false);
-}
-
 static struct v4l2_mbus_framefmt *
 __vdic_get_fmt(struct vdic_priv *priv, struct v4l2_subdev_pad_config *cfg,
 	       unsigned int pad, enum v4l2_subdev_format_whence which)
@@ -541,6 +527,16 @@ __vdic_get_fmt(struct vdic_priv *priv, struct v4l2_subdev_pad_config *cfg,
 		return &priv->format_mbus[pad];
 }
 
+static int vdic_enum_mbus_code(struct v4l2_subdev *sd,
+			       struct v4l2_subdev_pad_config *cfg,
+			       struct v4l2_subdev_mbus_code_enum *code)
+{
+	if (code->pad >= VDIC_NUM_PADS)
+		return -EINVAL;
+
+	return imx_media_enum_ipu_format(&code->code, code->index, CS_SEL_YUV);
+}
+
 static int vdic_get_fmt(struct v4l2_subdev *sd,
 			struct v4l2_subdev_pad_config *cfg,
 			struct v4l2_subdev_format *sdformat)
@@ -586,49 +582,28 @@ static int vdic_set_fmt(struct v4l2_subdev *sd,
 		goto out;
 	}
 
-	v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W_VDIC,
-			      W_ALIGN, &sdformat->format.height,
-			      MIN_H, MAX_H_VDIC, H_ALIGN, S_ALIGN);
+	cc = imx_media_find_ipu_format(sdformat->format.code, CS_SEL_YUV);
+	if (!cc) {
+		imx_media_enum_ipu_format(&code, 0, CS_SEL_YUV);
+		cc = imx_media_find_ipu_format(code, CS_SEL_YUV);
+		sdformat->format.code = cc->codes[0];
+	}
 
 	switch (sdformat->pad) {
 	case VDIC_SRC_PAD_DIRECT:
 		infmt = __vdic_get_fmt(priv, cfg, priv->active_input_pad,
 				       sdformat->which);
-
-		cc = imx_media_find_ipu_format(0, sdformat->format.code, false);
-		if (!cc) {
-			imx_media_enum_ipu_format(NULL, &code, 0, false);
-			cc = imx_media_find_ipu_format(0, code, false);
-			sdformat->format.code = cc->codes[0];
-		}
-
 		sdformat->format.width = infmt->width;
 		sdformat->format.height = infmt->height;
 		/* output is always progressive! */
 		sdformat->format.field = V4L2_FIELD_NONE;
 		break;
-	case VDIC_SINK_PAD_IDMAC:
 	case VDIC_SINK_PAD_DIRECT:
-		if (sdformat->pad == VDIC_SINK_PAD_DIRECT) {
-			cc = imx_media_find_ipu_format(0, sdformat->format.code,
-						       false);
-			if (!cc) {
-				imx_media_enum_ipu_format(NULL, &code, 0,
-							  false);
-				cc = imx_media_find_ipu_format(0, code, false);
-				sdformat->format.code = cc->codes[0];
-			}
-		} else {
-			cc = imx_media_find_format(0, sdformat->format.code,
-						   false, false);
-			if (!cc) {
-				imx_media_enum_format(NULL, &code, 0,
-						      false, false);
-				cc = imx_media_find_format(0, code,
-							   false, false);
-				sdformat->format.code = cc->codes[0];
-			}
-		}
+	case VDIC_SINK_PAD_IDMAC:
+		v4l_bound_align_image(&sdformat->format.width,
+				      MIN_W, MAX_W_VDIC, W_ALIGN,
+				      &sdformat->format.height,
+				      MIN_H, MAX_H_VDIC, H_ALIGN, S_ALIGN);
 
 		/* input must be interlaced! Choose SEQ_TB if not */
 		if (!V4L2_FIELD_HAS_BOTH(sdformat->format.field))
@@ -814,7 +789,7 @@ static int vdic_registered(struct v4l2_subdev *sd)
 
 		code = 0;
 		if (i != VDIC_SINK_PAD_IDMAC)
-			imx_media_enum_ipu_format(NULL, &code, 0, true);
+			imx_media_enum_ipu_format(&code, 0, CS_SEL_YUV);
 
 		/* set a default mbus format  */
 		ret = imx_media_init_mbus_fmt(&priv->format_mbus[i],
diff --git a/drivers/staging/media/imx/imx-media.h b/drivers/staging/media/imx/imx-media.h
index a67ee14..2342422 100644
--- a/drivers/staging/media/imx/imx-media.h
+++ b/drivers/staging/media/imx/imx-media.h
@@ -171,16 +171,23 @@ struct imx_media_dev {
 	struct v4l2_async_notifier subdev_notifier;
 };
 
-const struct imx_media_pixfmt *imx_media_find_format(u32 fourcc, u32 code,
-						     bool allow_rgb,
-						     bool allow_planar);
-const struct imx_media_pixfmt *imx_media_find_ipu_format(u32 fourcc, u32 code,
-							 bool allow_rgb);
-
-int imx_media_enum_format(u32 *fourcc, u32 *code, u32 index,
-			  bool allow_rgb, bool allow_planar);
-int imx_media_enum_ipu_format(u32 *fourcc, u32 *code, u32 index,
-			      bool allow_rgb);
+enum codespace_sel {
+	CS_SEL_YUV = 0,
+	CS_SEL_RGB,
+	CS_SEL_ANY,
+};
+
+const struct imx_media_pixfmt *
+imx_media_find_format(u32 fourcc, enum codespace_sel cs_sel);
+int imx_media_enum_format(u32 *fourcc, u32 index, enum codespace_sel cs_sel);
+const struct imx_media_pixfmt *
+imx_media_find_mbus_format(u32 code, enum codespace_sel cs_sel,
+			   bool allow_bayer);
+int imx_media_enum_mbus_format(u32 *code, u32 index, enum codespace_sel cs_sel,
+			       bool allow_bayer);
+const struct imx_media_pixfmt *
+imx_media_find_ipu_format(u32 code, enum codespace_sel cs_sel);
+int imx_media_enum_ipu_format(u32 *code, u32 index, enum codespace_sel cs_sel);
 
 int imx_media_init_mbus_fmt(struct v4l2_mbus_framefmt *mbus,
 			    u32 width, u32 height, u32 code, u32 field,
-- 
2.7.4

[PATCH v5 36/39] media: imx: redo pixel format enumeration and negotiation

[Steve Longerbeam]

The previous API and negotiation of mbus codes and pixel formats
was broken, and has been completely redone.

The negotiation of media bus codes should be as follows:

CSI:

sink pad     direct src pad      IDMAC src pad
--------     ----------------    -------------
RGB (any)        IPU RGB           IPU RGB
YUV (any)        IPU YUV           IPU YUV
Bayer              N/A             must be same bayer code as sink

VDIC:

direct sink pad    IDMAC sink pad    direct src pad
---------------    --------------    --------------
IPU YUV only       IPU YUV only       IPU YUV only

PRP:

direct sink pad    direct src pads
---------------    ---------------
IPU (any)          same as sink code

PRP ENC/VF:

direct sink pad    IDMAC src pads
---------------    --------------
IPU (any)          IPU RGB or IPU YUV

Given the above, a new internal API is created:

enum codespace_sel {
       CS_SEL_YUV = 0, /* find or enumerate only YUV codes */
       CS_SEL_RGB,     /* find or enumerate only RGB codes */
       CS_SEL_ANY,     /* find or enumerate both YUV and RGB codes */
};

/* Find and enumerate fourcc pixel formats */
const struct imx_media_pixfmt *
imx_media_find_format(u32 fourcc, enum codespace_sel cs_sel);
int imx_media_enum_format(u32 *fourcc, u32 index, enum codespace_sel cs_sel);

/* Find and enumerate media bus codes */
const struct imx_media_pixfmt *
imx_media_find_mbus_format(u32 code, enum codespace_sel cs_sel,
                          bool allow_bayer);
int imx_media_enum_mbus_format(u32 *code, u32 index, enum codespace_sel cs_sel,
                              bool allow_bayer);

/* Find and enumerate IPU internal media bus codes */
const struct imx_media_pixfmt *
imx_media_find_ipu_format(u32 code, enum codespace_sel cs_sel);
int imx_media_enum_ipu_format(u32 *code, u32 index, enum codespace_sel cs_sel);

The tables have been split into separate tables for YUV and RGB formats
to support the implementation of the above.

The subdev's .enum_mbus_code() and .set_fmt() operations have
been rewritten using the above APIs.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/imx-ic-prp.c        |  77 ++++--
 drivers/staging/media/imx/imx-ic-prpencvf.c   |  57 ++--
 drivers/staging/media/imx/imx-media-capture.c |  85 ++++--
 drivers/staging/media/imx/imx-media-csi.c     | 108 +++++---
 drivers/staging/media/imx/imx-media-utils.c   | 371 +++++++++++++++++++-------
 drivers/staging/media/imx/imx-media-vdic.c    |  69 ++---
 drivers/staging/media/imx/imx-media.h         |  27 +-
 7 files changed, 504 insertions(+), 290 deletions(-)

diff --git a/drivers/staging/media/imx/imx-ic-prp.c b/drivers/staging/media/imx/imx-ic-prp.c
index 1832915..83cd2b4 100644
--- a/drivers/staging/media/imx/imx-ic-prp.c
+++ b/drivers/staging/media/imx/imx-ic-prp.c
@@ -89,16 +89,6 @@ static void prp_stop(struct prp_priv *priv)
 {
 }
 
-static int prp_enum_mbus_code(struct v4l2_subdev *sd,
-			      struct v4l2_subdev_pad_config *cfg,
-			      struct v4l2_subdev_mbus_code_enum *code)
-{
-	if (code->pad >= PRP_NUM_PADS)
-		return -EINVAL;
-
-	return imx_media_enum_ipu_format(NULL, &code->code, code->index, true);
-}
-
 static struct v4l2_mbus_framefmt *
 __prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_pad_config *cfg,
 	      unsigned int pad, enum v4l2_subdev_format_whence which)
@@ -115,6 +105,38 @@ __prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_pad_config *cfg,
  * V4L2 subdev operations.
  */
 
+static int prp_enum_mbus_code(struct v4l2_subdev *sd,
+			      struct v4l2_subdev_pad_config *cfg,
+			      struct v4l2_subdev_mbus_code_enum *code)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+	struct v4l2_mbus_framefmt *infmt;
+	int ret = 0;
+
+	mutex_lock(&priv->lock);
+
+	switch (code->pad) {
+	case PRP_SINK_PAD:
+		ret = imx_media_enum_ipu_format(&code->code, code->index,
+						CS_SEL_ANY);
+		break;
+	case PRP_SRC_PAD_PRPENC:
+	case PRP_SRC_PAD_PRPVF:
+		if (code->index != 0) {
+			ret = -EINVAL;
+			goto out;
+		}
+		infmt = __prp_get_fmt(priv, cfg, PRP_SINK_PAD, code->which);
+		code->code = infmt->code;
+		break;
+	default:
+		ret = -EINVAL;
+	}
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
 static int prp_get_fmt(struct v4l2_subdev *sd,
 		       struct v4l2_subdev_pad_config *cfg,
 		       struct v4l2_subdev_format *sdformat)
@@ -160,23 +182,28 @@ static int prp_set_fmt(struct v4l2_subdev *sd,
 		goto out;
 	}
 
-	cc = imx_media_find_ipu_format(0, sdformat->format.code, true);
-	if (!cc) {
-		imx_media_enum_ipu_format(NULL, &code, 0, true);
-		cc = imx_media_find_ipu_format(0, code, true);
-		sdformat->format.code = cc->codes[0];
-	}
-
-	v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
-			      W_ALIGN, &sdformat->format.height,
-			      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
-
-	/* Output pads mirror input pad */
-	if (sdformat->pad == PRP_SRC_PAD_PRPENC ||
-	    sdformat->pad == PRP_SRC_PAD_PRPVF) {
+	switch (sdformat->pad) {
+	case PRP_SINK_PAD:
+		v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
+				      W_ALIGN, &sdformat->format.height,
+				      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
+
+		cc = imx_media_find_ipu_format(sdformat->format.code,
+					       CS_SEL_ANY);
+		if (!cc) {
+			imx_media_enum_ipu_format(&code, 0, CS_SEL_ANY);
+			cc = imx_media_find_ipu_format(code, CS_SEL_ANY);
+			sdformat->format.code = cc->codes[0];
+		}
+		break;
+	case PRP_SRC_PAD_PRPENC:
+	case PRP_SRC_PAD_PRPVF:
+		/* Output pads mirror input pad */
 		infmt = __prp_get_fmt(priv, cfg, PRP_SINK_PAD,
 				      sdformat->which);
+		cc = imx_media_find_ipu_format(infmt->code, CS_SEL_ANY);
 		sdformat->format = *infmt;
+		break;
 	}
 
 	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
@@ -402,7 +429,7 @@ static int prp_registered(struct v4l2_subdev *sd)
 			MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
 
 		/* set a default mbus format  */
-		imx_media_enum_ipu_format(NULL, &code, 0, true);
+		imx_media_enum_ipu_format(&code, 0, CS_SEL_YUV);
 		ret = imx_media_init_mbus_fmt(&priv->format_mbus[i],
 					      640, 480, code, V4L2_FIELD_NONE,
 					      &priv->cc[i]);
diff --git a/drivers/staging/media/imx/imx-ic-prpencvf.c b/drivers/staging/media/imx/imx-ic-prpencvf.c
index bd89e9b..b42103c 100644
--- a/drivers/staging/media/imx/imx-ic-prpencvf.c
+++ b/drivers/staging/media/imx/imx-ic-prpencvf.c
@@ -702,20 +702,6 @@ static void prp_stop(struct prp_priv *priv)
 	prp_put_ipu_resources(priv);
 }
 
-static int prp_enum_mbus_code(struct v4l2_subdev *sd,
-			      struct v4l2_subdev_pad_config *cfg,
-			      struct v4l2_subdev_mbus_code_enum *code)
-{
-	if (code->pad >= PRPENCVF_NUM_PADS)
-		return -EINVAL;
-
-	if (code->pad == PRPENCVF_SRC_PAD)
-		return imx_media_enum_format(NULL, &code->code, code->index,
-					     true, false);
-
-	return imx_media_enum_ipu_format(NULL, &code->code, code->index, true);
-}
-
 static struct v4l2_mbus_framefmt *
 __prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_pad_config *cfg,
 	      unsigned int pad, enum v4l2_subdev_format_whence which)
@@ -732,6 +718,16 @@ __prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_pad_config *cfg,
  * V4L2 subdev operations.
  */
 
+static int prp_enum_mbus_code(struct v4l2_subdev *sd,
+			      struct v4l2_subdev_pad_config *cfg,
+			      struct v4l2_subdev_mbus_code_enum *code)
+{
+	if (code->pad >= PRPENCVF_NUM_PADS)
+		return -EINVAL;
+
+	return imx_media_enum_ipu_format(&code->code, code->index, CS_SEL_ANY);
+}
+
 static int prp_get_fmt(struct v4l2_subdev *sd,
 		       struct v4l2_subdev_pad_config *cfg,
 		       struct v4l2_subdev_format *sdformat)
@@ -777,18 +773,17 @@ static int prp_set_fmt(struct v4l2_subdev *sd,
 		goto out;
 	}
 
+	cc = imx_media_find_ipu_format(sdformat->format.code, CS_SEL_ANY);
+	if (!cc) {
+		imx_media_enum_ipu_format(&code, 0, CS_SEL_ANY);
+		cc = imx_media_find_ipu_format(code, CS_SEL_ANY);
+		sdformat->format.code = cc->codes[0];
+	}
+
 	if (sdformat->pad == PRPENCVF_SRC_PAD) {
 		infmt = __prp_get_fmt(priv, cfg, PRPENCVF_SINK_PAD,
 				      sdformat->which);
 
-		cc = imx_media_find_format(0, sdformat->format.code,
-					   true, false);
-		if (!cc) {
-			imx_media_enum_format(NULL, &code, 0, true, false);
-			cc = imx_media_find_format(0, code, true, false);
-			sdformat->format.code = cc->codes[0];
-		}
-
 		if (sdformat->format.field != V4L2_FIELD_NONE)
 			sdformat->format.field = infmt->field;
 
@@ -808,14 +803,6 @@ static int prp_set_fmt(struct v4l2_subdev *sd,
 					      infmt->height / 4, MAX_H_SRC,
 					      H_ALIGN_SRC, S_ALIGN);
 	} else {
-		cc = imx_media_find_ipu_format(0, sdformat->format.code,
-					       true);
-		if (!cc) {
-			imx_media_enum_ipu_format(NULL, &code, 0, true);
-			cc = imx_media_find_ipu_format(0, code, true);
-			sdformat->format.code = cc->codes[0];
-		}
-
 		v4l_bound_align_image(&sdformat->format.width,
 				      MIN_W_SINK, MAX_W_SINK, W_ALIGN_SINK,
 				      &sdformat->format.height,
@@ -1098,15 +1085,11 @@ static int prp_registered(struct v4l2_subdev *sd)
 	priv->md = dev_get_drvdata(sd->v4l2_dev->dev);
 
 	for (i = 0; i < PRPENCVF_NUM_PADS; i++) {
-		if (i == PRPENCVF_SINK_PAD) {
-			priv->pad[i].flags = MEDIA_PAD_FL_SINK;
-			imx_media_enum_ipu_format(NULL, &code, 0, true);
-		} else {
-			priv->pad[i].flags = MEDIA_PAD_FL_SOURCE;
-			code = 0;
-		}
+		priv->pad[i].flags = (i == PRPENCVF_SINK_PAD) ?
+			MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
 
 		/* set a default mbus format  */
+		imx_media_enum_ipu_format(&code, 0, CS_SEL_YUV);
 		ret = imx_media_init_mbus_fmt(&priv->format_mbus[i],
 					      640, 480, code, V4L2_FIELD_NONE,
 					      &priv->cc[i]);
diff --git a/drivers/staging/media/imx/imx-media-capture.c b/drivers/staging/media/imx/imx-media-capture.c
index 704ed85..a757e05 100644
--- a/drivers/staging/media/imx/imx-media-capture.c
+++ b/drivers/staging/media/imx/imx-media-capture.c
@@ -85,12 +85,39 @@ static int vidioc_querycap(struct file *file, void *fh,
 static int capture_enum_fmt_vid_cap(struct file *file, void *fh,
 				    struct v4l2_fmtdesc *f)
 {
+	struct capture_priv *priv = video_drvdata(file);
+	const struct imx_media_pixfmt *cc_src;
+	struct v4l2_subdev_format fmt_src;
 	u32 fourcc;
 	int ret;
 
-	ret = imx_media_enum_format(&fourcc, NULL, f->index, true, true);
-	if (ret)
+	fmt_src.pad = priv->src_sd_pad;
+	fmt_src.which = V4L2_SUBDEV_FORMAT_ACTIVE;
+	ret = v4l2_subdev_call(priv->src_sd, pad, get_fmt, NULL, &fmt_src);
+	if (ret) {
+		v4l2_err(priv->src_sd, "failed to get src_sd format\n");
 		return ret;
+	}
+
+	cc_src = imx_media_find_ipu_format(fmt_src.format.code, CS_SEL_ANY);
+	if (!cc_src)
+		cc_src = imx_media_find_mbus_format(fmt_src.format.code,
+						    CS_SEL_ANY, true);
+	if (!cc_src)
+		return -EINVAL;
+
+	if (cc_src->bayer) {
+		if (f->index != 0)
+			return -EINVAL;
+		fourcc = cc_src->fourcc;
+	} else {
+		u32 cs_sel = (cc_src->cs == IPUV3_COLORSPACE_YUV) ?
+			CS_SEL_YUV : CS_SEL_RGB;
+
+		ret = imx_media_enum_format(&fourcc, f->index, cs_sel);
+		if (ret)
+			return ret;
+	}
 
 	f->pixelformat = fourcc;
 
@@ -112,40 +139,40 @@ static int capture_try_fmt_vid_cap(struct file *file, void *fh,
 {
 	struct capture_priv *priv = video_drvdata(file);
 	struct v4l2_subdev_format fmt_src;
-	const struct imx_media_pixfmt *cc, *src_cc;
-	u32 fourcc;
+	const struct imx_media_pixfmt *cc, *cc_src;
 	int ret;
 
-	fourcc = f->fmt.pix.pixelformat;
-	cc = imx_media_find_format(fourcc, 0, true, true);
-	if (!cc) {
-		imx_media_enum_format(&fourcc, NULL, 0, true, true);
-		cc = imx_media_find_format(fourcc, 0, true, true);
-	}
-
-	/*
-	 * user frame dimensions are the same as src_sd's pad.
-	 */
 	fmt_src.pad = priv->src_sd_pad;
 	fmt_src.which = V4L2_SUBDEV_FORMAT_ACTIVE;
 	ret = v4l2_subdev_call(priv->src_sd, pad, get_fmt, NULL, &fmt_src);
 	if (ret)
 		return ret;
 
-	/*
-	 * but we can allow planar pixel formats if the src_sd's
-	 * pad configured a YUV format
-	 */
-	src_cc = imx_media_find_format(0, fmt_src.format.code, true, false);
-	if (src_cc->cs == IPUV3_COLORSPACE_YUV &&
-	    cc->cs == IPUV3_COLORSPACE_YUV) {
-		imx_media_mbus_fmt_to_pix_fmt(&f->fmt.pix,
-					      &fmt_src.format, cc);
+	cc_src = imx_media_find_ipu_format(fmt_src.format.code, CS_SEL_ANY);
+	if (!cc_src)
+		cc_src = imx_media_find_mbus_format(fmt_src.format.code,
+						    CS_SEL_ANY, true);
+	if (!cc_src)
+		return -EINVAL;
+
+	if (cc_src->bayer) {
+		cc = cc_src;
 	} else {
-		imx_media_mbus_fmt_to_pix_fmt(&f->fmt.pix,
-					      &fmt_src.format, src_cc);
+		u32 fourcc, cs_sel;
+
+		cs_sel = (cc_src->cs == IPUV3_COLORSPACE_YUV) ?
+			CS_SEL_YUV : CS_SEL_RGB;
+		fourcc = f->fmt.pix.pixelformat;
+
+		cc = imx_media_find_format(fourcc, cs_sel);
+		if (!cc) {
+			imx_media_enum_format(&fourcc, 0, cs_sel);
+			cc = imx_media_find_format(fourcc, cs_sel);
+		}
 	}
 
+	imx_media_mbus_fmt_to_pix_fmt(&f->fmt.pix, &fmt_src.format, cc);
+
 	return 0;
 }
 
@@ -165,8 +192,8 @@ static int capture_s_fmt_vid_cap(struct file *file, void *fh,
 		return ret;
 
 	priv->vdev.fmt.fmt.pix = f->fmt.pix;
-	priv->vdev.cc = imx_media_find_format(f->fmt.pix.pixelformat, 0,
-					      true, true);
+	priv->vdev.cc = imx_media_find_format(f->fmt.pix.pixelformat,
+					      CS_SEL_ANY);
 
 	return 0;
 }
@@ -574,8 +601,8 @@ int imx_media_capture_device_register(struct imx_media_video_dev *vdev)
 	vdev->fmt.type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
 	imx_media_mbus_fmt_to_pix_fmt(&vdev->fmt.fmt.pix,
 				      &fmt_src.format, NULL);
-	vdev->cc = imx_media_find_format(0, fmt_src.format.code,
-					 true, false);
+	vdev->cc = imx_media_find_format(vdev->fmt.fmt.pix.pixelformat,
+					 CS_SEL_ANY);
 
 	v4l2_info(sd, "Registered %s as /dev/%s\n", vfd->name,
 		  video_device_node_name(vfd));
diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index b556fa4..a726744 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -917,15 +917,44 @@ static int csi_enum_mbus_code(struct v4l2_subdev *sd,
 			      struct v4l2_subdev_pad_config *cfg,
 			      struct v4l2_subdev_mbus_code_enum *code)
 {
-	if (code->pad >= CSI_NUM_PADS)
-		return -EINVAL;
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	const struct imx_media_pixfmt *incc;
+	struct v4l2_mbus_framefmt *infmt;
+	int ret = 0;
 
-	if (code->pad == CSI_SRC_PAD_DIRECT)
-		return imx_media_enum_ipu_format(NULL, &code->code,
-						 code->index, true);
+	mutex_lock(&priv->lock);
+
+	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, code->which);
+	incc = imx_media_find_mbus_format(infmt->code, CS_SEL_ANY, true);
 
-	return imx_media_enum_format(NULL, &code->code, code->index,
-				     true, false);
+	switch (code->pad) {
+	case CSI_SINK_PAD:
+		ret = imx_media_enum_mbus_format(&code->code, code->index,
+						 CS_SEL_ANY, true);
+		break;
+	case CSI_SRC_PAD_DIRECT:
+	case CSI_SRC_PAD_IDMAC:
+		if (incc->bayer) {
+			if (code->index != 0) {
+				ret = -EINVAL;
+				goto out;
+			}
+			code->code = infmt->code;
+		} else {
+			u32 cs_sel = (incc->cs == IPUV3_COLORSPACE_YUV) ?
+				CS_SEL_YUV : CS_SEL_RGB;
+			ret = imx_media_enum_ipu_format(&code->code,
+							code->index,
+							cs_sel);
+		}
+		break;
+	default:
+		ret = -EINVAL;
+	}
+
+out:
+	mutex_unlock(&priv->lock);
+	return ret;
 }
 
 static int csi_get_fmt(struct v4l2_subdev *sd,
@@ -981,14 +1010,13 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 		goto out;
 	}
 
-	v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
-			      W_ALIGN, &sdformat->format.height,
-			      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
-
 	switch (sdformat->pad) {
 	case CSI_SRC_PAD_DIRECT:
 	case CSI_SRC_PAD_IDMAC:
-		infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sdformat->which);
+		infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD,
+				      sdformat->which);
+		incc = imx_media_find_mbus_format(infmt->code,
+						  CS_SEL_ANY, true);
 
 		if (sdformat->format.width < priv->crop.width * 3 / 4)
 			sdformat->format.width = priv->crop.width / 2;
@@ -1000,38 +1028,25 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 		else
 			sdformat->format.height = priv->crop.height;
 
-		if (sdformat->pad == CSI_SRC_PAD_IDMAC) {
-			cc = imx_media_find_format(0, sdformat->format.code,
-						   true, false);
-			if (!cc) {
-				imx_media_enum_format(NULL, &code, 0,
-						      true, false);
-				cc = imx_media_find_format(0, code,
-							   true, false);
-				sdformat->format.code = cc->codes[0];
-			}
-
-			incc = priv->cc[CSI_SINK_PAD];
-			if (cc->cs != incc->cs) {
-				sdformat->format.code = infmt->code;
-				cc = imx_media_find_format(
-					0, sdformat->format.code,
-					true, false);
-			}
-
-			if (sdformat->format.field != V4L2_FIELD_NONE)
-				sdformat->format.field = infmt->field;
+		if (incc->bayer) {
+			sdformat->format.code = infmt->code;
+			cc = incc;
 		} else {
-			cc = imx_media_find_ipu_format(0, sdformat->format.code,
-						       true);
+			u32 cs_sel = (incc->cs == IPUV3_COLORSPACE_YUV) ?
+				CS_SEL_YUV : CS_SEL_RGB;
+
+			cc = imx_media_find_ipu_format(sdformat->format.code,
+						       cs_sel);
 			if (!cc) {
-				imx_media_enum_ipu_format(NULL, &code, 0, true);
-				cc = imx_media_find_ipu_format(0, code, true);
+				imx_media_enum_ipu_format(&code, 0, cs_sel);
+				cc = imx_media_find_ipu_format(code, cs_sel);
 				sdformat->format.code = cc->codes[0];
 			}
+		}
 
+		if (sdformat->pad == CSI_SRC_PAD_DIRECT ||
+		    sdformat->format.field != V4L2_FIELD_NONE)
 			sdformat->format.field = infmt->field;
-		}
 
 		/*
 		 * translate V4L2_FIELD_ALTERNATE to SEQ_TB or SEQ_BT
@@ -1044,6 +1059,9 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 		}
 		break;
 	case CSI_SINK_PAD:
+		v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
+				      W_ALIGN, &sdformat->format.height,
+				      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
 		crop.left = 0;
 		crop.top = 0;
 		crop.width = sdformat->format.width;
@@ -1053,11 +1071,13 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 		if (ret)
 			goto out;
 
-		cc = imx_media_find_format(0, sdformat->format.code,
-					   true, false);
+		cc = imx_media_find_mbus_format(sdformat->format.code,
+						CS_SEL_ANY, true);
 		if (!cc) {
-			imx_media_enum_format(NULL, &code, 0, true, false);
-			cc = imx_media_find_format(0, code, true, false);
+			imx_media_enum_mbus_format(&code, 0,
+						   CS_SEL_ANY, false);
+			cc = imx_media_find_mbus_format(code,
+							CS_SEL_ANY, false);
 			sdformat->format.code = cc->codes[0];
 		}
 		break;
@@ -1227,8 +1247,8 @@ static int csi_registered(struct v4l2_subdev *sd)
 			MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
 
 		code = 0;
-		if (i == CSI_SRC_PAD_DIRECT)
-			imx_media_enum_ipu_format(NULL, &code, 0, true);
+		if (i != CSI_SINK_PAD)
+			imx_media_enum_ipu_format(&code, 0, CS_SEL_YUV);
 
 		/* set a default mbus format  */
 		ret = imx_media_init_mbus_fmt(&priv->format_mbus[i],
diff --git a/drivers/staging/media/imx/imx-media-utils.c b/drivers/staging/media/imx/imx-media-utils.c
index 24e3795..a648fd5 100644
--- a/drivers/staging/media/imx/imx-media-utils.c
+++ b/drivers/staging/media/imx/imx-media-utils.c
@@ -12,14 +12,13 @@
 #include "imx-media.h"
 
 /*
- * List of pixel formats for the subdevs. This must be a super-set of
- * the formats supported by the ipu image converter.
+ * List of supported pixel formats for the subdevs.
  *
- * The non-mbus formats (planar and BGR) must all fall at the end of
- * this table, otherwise enum_fmt() at media pads will stop before
- * seeing all the supported mbus formats.
+ * In all of these tables, the non-mbus formats (with no
+ * mbus codes) must all fall at the end of the table.
  */
-static const struct imx_media_pixfmt imx_media_formats[] = {
+
+static const struct imx_media_pixfmt yuv_formats[] = {
 	{
 		.fourcc	= V4L2_PIX_FMT_UYVY,
 		.codes  = {
@@ -36,13 +35,45 @@ static const struct imx_media_pixfmt imx_media_formats[] = {
 		},
 		.cs     = IPUV3_COLORSPACE_YUV,
 		.bpp    = 16,
+	},
+	/***
+	 * non-mbus YUV formats start here. NOTE! when adding non-mbus
+	 * formats, NUM_NON_MBUS_YUV_FORMATS must be updated below.
+	 ***/
+	{
+		.fourcc	= V4L2_PIX_FMT_YUV420,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 12,
+		.planar = true,
 	}, {
-		.fourcc = V4L2_PIX_FMT_YUV32,
-		.codes  = {MEDIA_BUS_FMT_AYUV8_1X32},
+		.fourcc = V4L2_PIX_FMT_YVU420,
 		.cs     = IPUV3_COLORSPACE_YUV,
-		.bpp    = 32,
-		.ipufmt = true,
+		.bpp    = 12,
+		.planar = true,
 	}, {
+		.fourcc = V4L2_PIX_FMT_YUV422P,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 16,
+		.planar = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_NV12,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 12,
+		.planar = true,
+	}, {
+		.fourcc = V4L2_PIX_FMT_NV16,
+		.cs     = IPUV3_COLORSPACE_YUV,
+		.bpp    = 16,
+		.planar = true,
+	},
+};
+
+#define NUM_NON_MBUS_YUV_FORMATS 5
+#define NUM_YUV_FORMATS ARRAY_SIZE(yuv_formats)
+#define NUM_MBUS_YUV_FORMATS (NUM_YUV_FORMATS - NUM_NON_MBUS_YUV_FORMATS)
+
+static const struct imx_media_pixfmt rgb_formats[] = {
+	{
 		.fourcc	= V4L2_PIX_FMT_RGB565,
 		.codes  = {MEDIA_BUS_FMT_RGB565_2X8_LE},
 		.cs     = IPUV3_COLORSPACE_RGB,
@@ -61,7 +92,9 @@ static const struct imx_media_pixfmt imx_media_formats[] = {
 		.cs     = IPUV3_COLORSPACE_RGB,
 		.bpp    = 32,
 		.ipufmt = true,
-	}, {
+	},
+	/*** raw bayer formats start here ***/
+	{
 		.fourcc = V4L2_PIX_FMT_SBGGR8,
 		.codes  = {MEDIA_BUS_FMT_SBGGR8_1X8},
 		.cs     = IPUV3_COLORSPACE_RGB,
@@ -130,7 +163,10 @@ static const struct imx_media_pixfmt imx_media_formats[] = {
 		.bpp    = 16,
 		.bayer  = true,
 	},
-	/*** non-mbus formats start here ***/
+	/***
+	 * non-mbus RGB formats start here. NOTE! when adding non-mbus
+	 * formats, NUM_NON_MBUS_RGB_FORMATS must be updated below.
+	 ***/
 	{
 		.fourcc	= V4L2_PIX_FMT_BGR24,
 		.cs     = IPUV3_COLORSPACE_RGB,
@@ -139,135 +175,256 @@ static const struct imx_media_pixfmt imx_media_formats[] = {
 		.fourcc	= V4L2_PIX_FMT_BGR32,
 		.cs     = IPUV3_COLORSPACE_RGB,
 		.bpp    = 32,
-	}, {
-		.fourcc	= V4L2_PIX_FMT_YUV420,
-		.cs     = IPUV3_COLORSPACE_YUV,
-		.bpp    = 12,
-		.planar = true,
-	}, {
-		.fourcc = V4L2_PIX_FMT_YVU420,
-		.cs     = IPUV3_COLORSPACE_YUV,
-		.bpp    = 12,
-		.planar = true,
-	}, {
-		.fourcc = V4L2_PIX_FMT_YUV422P,
-		.cs     = IPUV3_COLORSPACE_YUV,
-		.bpp    = 16,
-		.planar = true,
-	}, {
-		.fourcc = V4L2_PIX_FMT_NV12,
-		.cs     = IPUV3_COLORSPACE_YUV,
-		.bpp    = 12,
-		.planar = true,
-	}, {
-		.fourcc = V4L2_PIX_FMT_NV16,
+	},
+};
+
+#define NUM_NON_MBUS_RGB_FORMATS 2
+#define NUM_RGB_FORMATS ARRAY_SIZE(rgb_formats)
+#define NUM_MBUS_RGB_FORMATS (NUM_RGB_FORMATS - NUM_NON_MBUS_RGB_FORMATS)
+
+static const struct imx_media_pixfmt ipu_yuv_formats[] = {
+	{
+		.fourcc = V4L2_PIX_FMT_YUV32,
+		.codes  = {MEDIA_BUS_FMT_AYUV8_1X32},
 		.cs     = IPUV3_COLORSPACE_YUV,
-		.bpp    = 16,
-		.planar = true,
+		.bpp    = 32,
+		.ipufmt = true,
 	},
 };
 
-static const u32 imx_media_ipu_internal_codes[] = {
-	MEDIA_BUS_FMT_AYUV8_1X32, MEDIA_BUS_FMT_ARGB8888_1X32,
+#define NUM_IPU_YUV_FORMATS ARRAY_SIZE(ipu_yuv_formats)
+
+static const struct imx_media_pixfmt ipu_rgb_formats[] = {
+	{
+		.fourcc	= V4L2_PIX_FMT_RGB32,
+		.codes  = {MEDIA_BUS_FMT_ARGB8888_1X32},
+		.cs     = IPUV3_COLORSPACE_RGB,
+		.bpp    = 32,
+		.ipufmt = true,
+	},
 };
 
+#define NUM_IPU_RGB_FORMATS ARRAY_SIZE(ipu_rgb_formats)
+
 static inline u32 pixfmt_to_colorspace(const struct imx_media_pixfmt *fmt)
 {
 	return (fmt->cs == IPUV3_COLORSPACE_RGB) ?
 		V4L2_COLORSPACE_SRGB : V4L2_COLORSPACE_SMPTE170M;
 }
 
-static const struct imx_media_pixfmt *find_format(u32 fourcc, u32 code,
-						  bool allow_rgb,
-						  bool allow_planar,
-						  bool ipu_fmt_only)
+static const struct imx_media_pixfmt *find_format(u32 fourcc,
+						  u32 code,
+						  enum codespace_sel cs_sel,
+						  bool allow_non_mbus,
+						  bool allow_bayer)
 {
-	const struct imx_media_pixfmt *fmt, *ret = NULL;
+	const struct imx_media_pixfmt *array, *fmt, *ret = NULL;
+	u32 array_size;
 	int i, j;
 
-	for (i = 0; i < ARRAY_SIZE(imx_media_formats); i++) {
-		fmt = &imx_media_formats[i];
+	switch (cs_sel) {
+	case CS_SEL_YUV:
+		array_size = NUM_YUV_FORMATS;
+		array = yuv_formats;
+		break;
+	case CS_SEL_RGB:
+		array_size = NUM_RGB_FORMATS;
+		array = rgb_formats;
+		break;
+	case CS_SEL_ANY:
+		array_size = NUM_YUV_FORMATS + NUM_RGB_FORMATS;
+		array = yuv_formats;
+		break;
+	default:
+		return NULL;
+	}
+
+	for (i = 0; i < array_size; i++) {
+		if (cs_sel == CS_SEL_ANY && i >= NUM_YUV_FORMATS)
+			fmt = &rgb_formats[i - NUM_YUV_FORMATS];
+		else
+			fmt = &array[i];
 
-		if (ipu_fmt_only && !fmt->ipufmt)
+		if ((!allow_non_mbus && fmt->codes[0] == 0) ||
+		    (!allow_bayer && fmt->bayer))
 			continue;
 
-		if (fourcc && fmt->fourcc == fourcc &&
-		    (fmt->cs != IPUV3_COLORSPACE_RGB || allow_rgb) &&
-		    (!fmt->planar || allow_planar)) {
+		if (fourcc && fmt->fourcc == fourcc) {
 			ret = fmt;
 			goto out;
 		}
 
 		for (j = 0; code && fmt->codes[j]; j++) {
-			if (fmt->codes[j] == code && !fmt->planar &&
-			    (fmt->cs != IPUV3_COLORSPACE_RGB || allow_rgb)) {
+			if (code == fmt->codes[j]) {
 				ret = fmt;
 				goto out;
 			}
 		}
 	}
+
 out:
 	return ret;
 }
 
-const struct imx_media_pixfmt *imx_media_find_format(u32 fourcc, u32 code,
-						     bool allow_rgb,
-						     bool allow_planar)
+static int enum_format(u32 *fourcc, u32 *code, u32 index,
+		       enum codespace_sel cs_sel,
+		       bool allow_non_mbus,
+		       bool allow_bayer)
+{
+	const struct imx_media_pixfmt *fmt;
+	u32 mbus_yuv_sz = NUM_MBUS_YUV_FORMATS;
+	u32 mbus_rgb_sz = NUM_MBUS_RGB_FORMATS;
+	u32 yuv_sz = NUM_YUV_FORMATS;
+	u32 rgb_sz = NUM_RGB_FORMATS;
+
+	switch (cs_sel) {
+	case CS_SEL_YUV:
+		if (index >= yuv_sz ||
+		    (!allow_non_mbus && index >= mbus_yuv_sz))
+			return -EINVAL;
+		fmt = &yuv_formats[index];
+		break;
+	case CS_SEL_RGB:
+		if (index >= rgb_sz ||
+		    (!allow_non_mbus && index >= mbus_rgb_sz))
+			return -EINVAL;
+		fmt = &rgb_formats[index];
+		if (!allow_bayer && fmt->bayer)
+			return -EINVAL;
+		break;
+	case CS_SEL_ANY:
+		if (!allow_non_mbus) {
+			if (index >= mbus_yuv_sz) {
+				index -= mbus_yuv_sz;
+				if (index >= mbus_rgb_sz)
+					return -EINVAL;
+				fmt = &rgb_formats[index];
+				if (!allow_bayer && fmt->bayer)
+					return -EINVAL;
+			} else {
+				fmt = &yuv_formats[index];
+			}
+		} else {
+			if (index >= yuv_sz + rgb_sz)
+				return -EINVAL;
+			if (index >= yuv_sz) {
+				fmt = &rgb_formats[index - yuv_sz];
+				if (!allow_bayer && fmt->bayer)
+					return -EINVAL;
+			} else {
+				fmt = &yuv_formats[index];
+			}
+		}
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	if (fourcc)
+		*fourcc = fmt->fourcc;
+	if (code)
+		*code = fmt->codes[0];
+
+	return 0;
+}
+
+const struct imx_media_pixfmt *
+imx_media_find_format(u32 fourcc, enum codespace_sel cs_sel)
 {
-	return find_format(fourcc, code, allow_rgb, allow_planar, false);
+	return find_format(fourcc, 0, cs_sel, true, false);
 }
 EXPORT_SYMBOL_GPL(imx_media_find_format);
 
-const struct imx_media_pixfmt *imx_media_find_ipu_format(u32 fourcc,
-							 u32 code,
-							 bool allow_rgb)
+int imx_media_enum_format(u32 *fourcc, u32 index, enum codespace_sel cs_sel)
 {
-	return find_format(fourcc, code, allow_rgb, false, true);
+	return enum_format(fourcc, NULL, index, cs_sel, true, false);
 }
-EXPORT_SYMBOL_GPL(imx_media_find_ipu_format);
+EXPORT_SYMBOL_GPL(imx_media_enum_format);
 
-int imx_media_enum_format(u32 *fourcc, u32 *code, u32 index,
-			  bool allow_rgb, bool allow_planar)
+const struct imx_media_pixfmt *
+imx_media_find_mbus_format(u32 code, enum codespace_sel cs_sel,
+			   bool allow_bayer)
 {
-	const struct imx_media_pixfmt *fmt;
+	return find_format(0, code, cs_sel, false, allow_bayer);
+}
+EXPORT_SYMBOL_GPL(imx_media_find_mbus_format);
 
-	if (index >= ARRAY_SIZE(imx_media_formats))
-		return -EINVAL;
+int imx_media_enum_mbus_format(u32 *code, u32 index, enum codespace_sel cs_sel,
+			       bool allow_bayer)
+{
+	return enum_format(NULL, code, index, cs_sel, false, allow_bayer);
+}
+EXPORT_SYMBOL_GPL(imx_media_enum_mbus_format);
 
-	fmt = &imx_media_formats[index];
+const struct imx_media_pixfmt *
+imx_media_find_ipu_format(u32 code, enum codespace_sel cs_sel)
+{
+	const struct imx_media_pixfmt *array, *fmt, *ret = NULL;
+	u32 array_size;
+	int i, j;
 
-	if ((fmt->cs == IPUV3_COLORSPACE_RGB && !allow_rgb) ||
-	    (fmt->planar && !allow_planar))
-		return -EINVAL;
+	switch (cs_sel) {
+	case CS_SEL_YUV:
+		array_size = NUM_IPU_YUV_FORMATS;
+		array = ipu_yuv_formats;
+		break;
+	case CS_SEL_RGB:
+		array_size = NUM_IPU_RGB_FORMATS;
+		array = ipu_rgb_formats;
+		break;
+	case CS_SEL_ANY:
+		array_size = NUM_IPU_YUV_FORMATS + NUM_IPU_RGB_FORMATS;
+		array = ipu_yuv_formats;
+		break;
+	default:
+		return NULL;
+	}
 
-	if (code)
-		*code = fmt->codes[0];
-	if (fourcc)
-		*fourcc = fmt->fourcc;
+	for (i = 0; i < array_size; i++) {
+		if (cs_sel == CS_SEL_ANY && i >= NUM_IPU_YUV_FORMATS)
+			fmt = &ipu_rgb_formats[i - NUM_IPU_YUV_FORMATS];
+		else
+			fmt = &array[i];
 
-	return 0;
+		for (j = 0; code && fmt->codes[j]; j++) {
+			if (code == fmt->codes[j]) {
+				ret = fmt;
+				goto out;
+			}
+		}
+	}
+
+out:
+	return ret;
 }
-EXPORT_SYMBOL_GPL(imx_media_enum_format);
+EXPORT_SYMBOL_GPL(imx_media_find_ipu_format);
 
-int imx_media_enum_ipu_format(u32 *fourcc, u32 *code, u32 index,
-			      bool allow_rgb)
+int imx_media_enum_ipu_format(u32 *code, u32 index, enum codespace_sel cs_sel)
 {
-	const struct imx_media_pixfmt *fmt;
-	u32 lcode;
-
-	if (index >= ARRAY_SIZE(imx_media_ipu_internal_codes))
-		return -EINVAL;
-
-	lcode = imx_media_ipu_internal_codes[index];
-
-	fmt = find_format(0, lcode, allow_rgb, false, true);
-	if (!fmt)
+	switch (cs_sel) {
+	case CS_SEL_YUV:
+		if (index >= NUM_IPU_YUV_FORMATS)
+			return -EINVAL;
+		*code = ipu_yuv_formats[index].codes[0];
+		break;
+	case CS_SEL_RGB:
+		if (index >= NUM_IPU_RGB_FORMATS)
+			return -EINVAL;
+		*code = ipu_rgb_formats[index].codes[0];
+		break;
+	case CS_SEL_ANY:
+		if (index >= NUM_IPU_YUV_FORMATS + NUM_IPU_RGB_FORMATS)
+			return -EINVAL;
+		if (index >= NUM_IPU_YUV_FORMATS) {
+			index -= NUM_IPU_YUV_FORMATS;
+			*code = ipu_rgb_formats[index].codes[0];
+		} else {
+			*code = ipu_yuv_formats[index].codes[0];
+		}
+		break;
+	default:
 		return -EINVAL;
-
-	if (code)
-		*code = fmt->codes[0];
-	if (fourcc)
-		*fourcc = fmt->fourcc;
+	}
 
 	return 0;
 }
@@ -283,10 +440,14 @@ int imx_media_init_mbus_fmt(struct v4l2_mbus_framefmt *mbus,
 	mbus->height = height;
 	mbus->field = field;
 	if (code == 0)
-		imx_media_enum_format(NULL, &code, 0, true, false);
-	lcc = imx_media_find_format(0, code, true, false);
-	if (!lcc)
-		return -EINVAL;
+		imx_media_enum_mbus_format(&code, 0, CS_SEL_YUV, false);
+	lcc = imx_media_find_mbus_format(code, CS_SEL_ANY, false);
+	if (!lcc) {
+		lcc = imx_media_find_ipu_format(code, CS_SEL_ANY);
+		if (!lcc)
+			return -EINVAL;
+	}
+
 	mbus->code = code;
 	mbus->colorspace = pixfmt_to_colorspace(lcc);
 
@@ -304,11 +465,25 @@ int imx_media_mbus_fmt_to_pix_fmt(struct v4l2_pix_format *pix,
 	u32 stride;
 
 	if (!cc) {
-		cc = imx_media_find_format(0, mbus->code, true, false);
+		cc = imx_media_find_ipu_format(mbus->code, CS_SEL_ANY);
+		if (!cc)
+			cc = imx_media_find_mbus_format(mbus->code, CS_SEL_ANY,
+							true);
 		if (!cc)
 			return -EINVAL;
 	}
 
+	/*
+	 * TODO: the IPU currently does not support the AYUV32 format,
+	 * so until it does convert to a supported YUV format.
+	 */
+	if (cc->ipufmt && cc->cs == IPUV3_COLORSPACE_YUV) {
+		u32 code;
+
+		imx_media_enum_mbus_format(&code, 0, CS_SEL_YUV, false);
+		cc = imx_media_find_mbus_format(code, CS_SEL_YUV, false);
+	}
+
 	stride = cc->planar ? mbus->width : (mbus->width * cc->bpp) >> 3;
 
 	pix->width = mbus->width;
@@ -349,7 +524,7 @@ int imx_media_ipu_image_to_mbus_fmt(struct v4l2_mbus_framefmt *mbus,
 {
 	const struct imx_media_pixfmt *fmt;
 
-	fmt = imx_media_find_format(image->pix.pixelformat, 0, true, false);
+	fmt = imx_media_find_format(image->pix.pixelformat, CS_SEL_ANY);
 	if (!fmt)
 		return -EINVAL;
 
diff --git a/drivers/staging/media/imx/imx-media-vdic.c b/drivers/staging/media/imx/imx-media-vdic.c
index 0e7c24c..070f9da 100644
--- a/drivers/staging/media/imx/imx-media-vdic.c
+++ b/drivers/staging/media/imx/imx-media-vdic.c
@@ -517,20 +517,6 @@ static int vdic_s_stream(struct v4l2_subdev *sd, int enable)
 	return ret;
 }
 
-static int vdic_enum_mbus_code(struct v4l2_subdev *sd,
-			       struct v4l2_subdev_pad_config *cfg,
-			       struct v4l2_subdev_mbus_code_enum *code)
-{
-	if (code->pad >= VDIC_NUM_PADS)
-		return -EINVAL;
-
-	if (code->pad == VDIC_SINK_PAD_IDMAC)
-		return imx_media_enum_format(NULL, &code->code, code->index,
-					     false, false);
-
-	return imx_media_enum_ipu_format(NULL, &code->code, code->index, false);
-}
-
 static struct v4l2_mbus_framefmt *
 __vdic_get_fmt(struct vdic_priv *priv, struct v4l2_subdev_pad_config *cfg,
 	       unsigned int pad, enum v4l2_subdev_format_whence which)
@@ -541,6 +527,16 @@ __vdic_get_fmt(struct vdic_priv *priv, struct v4l2_subdev_pad_config *cfg,
 		return &priv->format_mbus[pad];
 }
 
+static int vdic_enum_mbus_code(struct v4l2_subdev *sd,
+			       struct v4l2_subdev_pad_config *cfg,
+			       struct v4l2_subdev_mbus_code_enum *code)
+{
+	if (code->pad >= VDIC_NUM_PADS)
+		return -EINVAL;
+
+	return imx_media_enum_ipu_format(&code->code, code->index, CS_SEL_YUV);
+}
+
 static int vdic_get_fmt(struct v4l2_subdev *sd,
 			struct v4l2_subdev_pad_config *cfg,
 			struct v4l2_subdev_format *sdformat)
@@ -586,49 +582,28 @@ static int vdic_set_fmt(struct v4l2_subdev *sd,
 		goto out;
 	}
 
-	v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W_VDIC,
-			      W_ALIGN, &sdformat->format.height,
-			      MIN_H, MAX_H_VDIC, H_ALIGN, S_ALIGN);
+	cc = imx_media_find_ipu_format(sdformat->format.code, CS_SEL_YUV);
+	if (!cc) {
+		imx_media_enum_ipu_format(&code, 0, CS_SEL_YUV);
+		cc = imx_media_find_ipu_format(code, CS_SEL_YUV);
+		sdformat->format.code = cc->codes[0];
+	}
 
 	switch (sdformat->pad) {
 	case VDIC_SRC_PAD_DIRECT:
 		infmt = __vdic_get_fmt(priv, cfg, priv->active_input_pad,
 				       sdformat->which);
-
-		cc = imx_media_find_ipu_format(0, sdformat->format.code, false);
-		if (!cc) {
-			imx_media_enum_ipu_format(NULL, &code, 0, false);
-			cc = imx_media_find_ipu_format(0, code, false);
-			sdformat->format.code = cc->codes[0];
-		}
-
 		sdformat->format.width = infmt->width;
 		sdformat->format.height = infmt->height;
 		/* output is always progressive! */
 		sdformat->format.field = V4L2_FIELD_NONE;
 		break;
-	case VDIC_SINK_PAD_IDMAC:
 	case VDIC_SINK_PAD_DIRECT:
-		if (sdformat->pad == VDIC_SINK_PAD_DIRECT) {
-			cc = imx_media_find_ipu_format(0, sdformat->format.code,
-						       false);
-			if (!cc) {
-				imx_media_enum_ipu_format(NULL, &code, 0,
-							  false);
-				cc = imx_media_find_ipu_format(0, code, false);
-				sdformat->format.code = cc->codes[0];
-			}
-		} else {
-			cc = imx_media_find_format(0, sdformat->format.code,
-						   false, false);
-			if (!cc) {
-				imx_media_enum_format(NULL, &code, 0,
-						      false, false);
-				cc = imx_media_find_format(0, code,
-							   false, false);
-				sdformat->format.code = cc->codes[0];
-			}
-		}
+	case VDIC_SINK_PAD_IDMAC:
+		v4l_bound_align_image(&sdformat->format.width,
+				      MIN_W, MAX_W_VDIC, W_ALIGN,
+				      &sdformat->format.height,
+				      MIN_H, MAX_H_VDIC, H_ALIGN, S_ALIGN);
 
 		/* input must be interlaced! Choose SEQ_TB if not */
 		if (!V4L2_FIELD_HAS_BOTH(sdformat->format.field))
@@ -814,7 +789,7 @@ static int vdic_registered(struct v4l2_subdev *sd)
 
 		code = 0;
 		if (i != VDIC_SINK_PAD_IDMAC)
-			imx_media_enum_ipu_format(NULL, &code, 0, true);
+			imx_media_enum_ipu_format(&code, 0, CS_SEL_YUV);
 
 		/* set a default mbus format  */
 		ret = imx_media_init_mbus_fmt(&priv->format_mbus[i],
diff --git a/drivers/staging/media/imx/imx-media.h b/drivers/staging/media/imx/imx-media.h
index a67ee14..2342422 100644
--- a/drivers/staging/media/imx/imx-media.h
+++ b/drivers/staging/media/imx/imx-media.h
@@ -171,16 +171,23 @@ struct imx_media_dev {
 	struct v4l2_async_notifier subdev_notifier;
 };
 
-const struct imx_media_pixfmt *imx_media_find_format(u32 fourcc, u32 code,
-						     bool allow_rgb,
-						     bool allow_planar);
-const struct imx_media_pixfmt *imx_media_find_ipu_format(u32 fourcc, u32 code,
-							 bool allow_rgb);
-
-int imx_media_enum_format(u32 *fourcc, u32 *code, u32 index,
-			  bool allow_rgb, bool allow_planar);
-int imx_media_enum_ipu_format(u32 *fourcc, u32 *code, u32 index,
-			      bool allow_rgb);
+enum codespace_sel {
+	CS_SEL_YUV = 0,
+	CS_SEL_RGB,
+	CS_SEL_ANY,
+};
+
+const struct imx_media_pixfmt *
+imx_media_find_format(u32 fourcc, enum codespace_sel cs_sel);
+int imx_media_enum_format(u32 *fourcc, u32 index, enum codespace_sel cs_sel);
+const struct imx_media_pixfmt *
+imx_media_find_mbus_format(u32 code, enum codespace_sel cs_sel,
+			   bool allow_bayer);
+int imx_media_enum_mbus_format(u32 *code, u32 index, enum codespace_sel cs_sel,
+			       bool allow_bayer);
+const struct imx_media_pixfmt *
+imx_media_find_ipu_format(u32 code, enum codespace_sel cs_sel);
+int imx_media_enum_ipu_format(u32 *code, u32 index, enum codespace_sel cs_sel);
 
 int imx_media_init_mbus_fmt(struct v4l2_mbus_framefmt *mbus,
 			    u32 width, u32 height, u32 code, u32 field,
-- 
2.7.4

[PATCH v5 37/39] media: imx: csi: add frame skipping support

[Steve Longerbeam]

From: Philipp Zabel <p.zabel@pengutronix.de>

The CSI can skip any out of up to 6 input frames, allowing to reduce the
frame rate at the output pads by small fractions.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/imx-media-csi.c | 125 ++++++++++++++++++++++++++++--
 1 file changed, 120 insertions(+), 5 deletions(-)

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index a726744..e5105ec 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -1,13 +1,15 @@
 /*
  * V4L2 Capture CSI Subdev for Freescale i.MX5/6 SOC
  *
- * Copyright (c) 2014-2016 Mentor Graphics Inc.
+ * Copyright (c) 2014-2017 Mentor Graphics Inc.
+ * Copyright (C) 2017 Pengutronix, Philipp Zabel <kernel@pengutronix.de>
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation; either version 2 of the License, or
  * (at your option) any later version.
  */
+#include <linux/gcd.h>
 #include <linux/interrupt.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
@@ -40,6 +42,18 @@
 #define H_ALIGN    1 /* multiple of 2 lines */
 #define S_ALIGN    1 /* multiple of 2 */
 
+/*
+ * struct csi_skip_desc - CSI frame skipping descriptor
+ * @keep - number of frames kept per max_ratio frames
+ * @max_ratio - width of skip_smfc, written to MAX_RATIO bitfield
+ * @skip_smfc - skip pattern written to the SKIP_SMFC bitfield
+ */
+struct csi_skip_desc {
+	u8 keep;
+	u8 max_ratio;
+	u8 skip_smfc;
+};
+
 struct csi_priv {
 	struct device *dev;
 	struct ipu_soc *ipu;
@@ -65,6 +79,7 @@ struct csi_priv {
 	const struct imx_media_pixfmt *cc[CSI_NUM_PADS];
 	struct v4l2_fract frame_interval;
 	struct v4l2_rect crop;
+	const struct csi_skip_desc *skip[CSI_NUM_PADS - 1];
 
 	/* active vb2 buffers to send to video dev sink */
 	struct imx_media_buffer *active_vb2_buf[2];
@@ -517,10 +532,12 @@ static int csi_setup(struct csi_priv *priv)
 	struct v4l2_mbus_config sensor_mbus_cfg;
 	struct v4l2_of_endpoint *sensor_ep;
 	struct v4l2_mbus_framefmt if_fmt;
+	const struct csi_skip_desc *skip;
 
 	infmt = &priv->format_mbus[CSI_SINK_PAD];
 	outfmt = &priv->format_mbus[priv->active_output_pad];
 	sensor_ep = &priv->sensor->sensor_ep;
+	skip = priv->skip[priv->active_output_pad - 1];
 
 	/* compose mbus_config from sensor endpoint */
 	sensor_mbus_cfg.type = sensor_ep->bus_type;
@@ -545,6 +562,9 @@ static int csi_setup(struct csi_priv *priv)
 
 	ipu_csi_set_dest(priv->csi, priv->dest);
 
+	ipu_csi_set_skip_smfc(priv->csi, skip->skip_smfc, skip->max_ratio - 1,
+			      0);
+
 	ipu_csi_dump(priv->csi);
 
 	return 0;
@@ -608,6 +628,77 @@ static void csi_stop(struct csi_priv *priv)
 	ipu_csi_disable(priv->csi);
 }
 
+static const struct csi_skip_desc csi_skip[12] = {
+	{ 1, 1, 0x00 }, /* Keep all frames */
+	{ 5, 6, 0x10 }, /* Skip every sixth frame */
+	{ 4, 5, 0x08 }, /* Skip every fifth frame */
+	{ 3, 4, 0x04 }, /* Skip every fourth frame */
+	{ 2, 3, 0x02 }, /* Skip every third frame */
+	{ 3, 5, 0x0a }, /* Skip frames 1 and 3 of every 5 */
+	{ 1, 2, 0x01 }, /* Skip every second frame */
+	{ 2, 5, 0x0b }, /* Keep frames 1 and 4 of every 5 */
+	{ 1, 3, 0x03 }, /* Keep one in three frames */
+	{ 1, 4, 0x07 }, /* Keep one in four frames */
+	{ 1, 5, 0x0f }, /* Keep one in five frames */
+	{ 1, 6, 0x1f }, /* Keep one in six frames */
+};
+
+static void csi_apply_skip_interval(const struct csi_skip_desc *skip,
+				    struct v4l2_fract *interval)
+{
+	unsigned int div;
+
+	interval->numerator *= skip->max_ratio;
+	interval->denominator *= skip->keep;
+
+	/* Reduce fraction to lowest terms */
+	div = gcd(interval->numerator, interval->denominator);
+	if (div > 1) {
+		interval->numerator /= div;
+		interval->denominator /= div;
+	}
+}
+
+/*
+ * Find the skip pattern to produce the output frame interval closest to the
+ * requested one, for the given input frame interval. Updates the output frame
+ * interval to the exact value.
+ */
+static const struct csi_skip_desc *csi_find_best_skip(struct v4l2_fract *in,
+						      struct v4l2_fract *out)
+{
+	const struct csi_skip_desc *skip = &csi_skip[0], *best_skip = skip;
+	u32 min_err = UINT_MAX;
+	u64 want_us;
+	int i;
+
+	/* Default to 1:1 ratio */
+	if (out->numerator == 0 || out->denominator == 0 ||
+	    in->numerator == 0 || in->denominator == 0)
+		return best_skip;
+
+	want_us = div_u64((u64)USEC_PER_SEC * out->numerator, out->denominator);
+
+	/* Find the reduction closest to the requested time per frame */
+	for (i = 0; i < ARRAY_SIZE(csi_skip); i++, skip++) {
+		u64 tmp, err;
+
+		tmp = div_u64((u64)USEC_PER_SEC * in->numerator *
+			      skip->max_ratio, in->denominator * skip->keep);
+
+		err = abs((s64)tmp - want_us);
+		if (err < min_err) {
+			min_err = err;
+			best_skip = skip;
+		}
+	}
+
+	*out = *in;
+	csi_apply_skip_interval(best_skip, out);
+
+	return best_skip;
+}
+
 /*
  * V4L2 subdev operations.
  */
@@ -617,8 +708,16 @@ static int csi_g_frame_interval(struct v4l2_subdev *sd,
 {
 	struct csi_priv *priv = v4l2_get_subdevdata(sd);
 
+	if (fi->pad >= CSI_NUM_PADS)
+		return -EINVAL;
+
 	mutex_lock(&priv->lock);
+
 	fi->interval = priv->frame_interval;
+
+	if (fi->pad != CSI_SINK_PAD)
+		csi_apply_skip_interval(priv->skip[fi->pad - 1], &fi->interval);
+
 	mutex_unlock(&priv->lock);
 
 	return 0;
@@ -629,14 +728,27 @@ static int csi_s_frame_interval(struct v4l2_subdev *sd,
 {
 	struct csi_priv *priv = v4l2_get_subdevdata(sd);
 
+	if (fi->pad >= CSI_NUM_PADS)
+		return -EINVAL;
+
 	mutex_lock(&priv->lock);
 
-	/* Output pads mirror active input pad, no limits on input pads */
-	if (fi->pad == CSI_SRC_PAD_IDMAC || fi->pad == CSI_SRC_PAD_DIRECT)
-		fi->interval = priv->frame_interval;
+	/* No limits on input pad */
+	if (fi->pad == CSI_SINK_PAD) {
+		priv->frame_interval = fi->interval;
+
+		/* Reset frame skipping ratio to 1:1 */
+		priv->skip[0] = &csi_skip[0];
+		priv->skip[1] = &csi_skip[0];
 
-	priv->frame_interval = fi->interval;
+		goto out;
+	}
+
+	/* Output pads depend on input interval, modified by frame skipping */
+	priv->skip[fi->pad - 1] = csi_find_best_skip(&priv->frame_interval,
+						     &fi->interval);
 
+out:
 	mutex_unlock(&priv->lock);
 
 	return 0;
@@ -1256,6 +1368,9 @@ static int csi_registered(struct v4l2_subdev *sd)
 					      &priv->cc[i]);
 		if (ret)
 			goto put_csi;
+		/* disable frame skipping */
+		if (i != CSI_SINK_PAD)
+			priv->skip[i - 1] = &csi_skip[0];
 	}
 
 	/* init default frame interval */
-- 
2.7.4

[PATCH v5 37/39] media: imx: csi: add frame skipping support

[Steve Longerbeam]

From: Philipp Zabel <p.zabel@pengutronix.de>

The CSI can skip any out of up to 6 input frames, allowing to reduce the
frame rate at the output pads by small fractions.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/imx-media-csi.c | 125 ++++++++++++++++++++++++++++--
 1 file changed, 120 insertions(+), 5 deletions(-)

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index a726744..e5105ec 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -1,13 +1,15 @@
 /*
  * V4L2 Capture CSI Subdev for Freescale i.MX5/6 SOC
  *
- * Copyright (c) 2014-2016 Mentor Graphics Inc.
+ * Copyright (c) 2014-2017 Mentor Graphics Inc.
+ * Copyright (C) 2017 Pengutronix, Philipp Zabel <kernel@pengutronix.de>
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation; either version 2 of the License, or
  * (at your option) any later version.
  */
+#include <linux/gcd.h>
 #include <linux/interrupt.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
@@ -40,6 +42,18 @@
 #define H_ALIGN    1 /* multiple of 2 lines */
 #define S_ALIGN    1 /* multiple of 2 */
 
+/*
+ * struct csi_skip_desc - CSI frame skipping descriptor
+ * @keep - number of frames kept per max_ratio frames
+ * @max_ratio - width of skip_smfc, written to MAX_RATIO bitfield
+ * @skip_smfc - skip pattern written to the SKIP_SMFC bitfield
+ */
+struct csi_skip_desc {
+	u8 keep;
+	u8 max_ratio;
+	u8 skip_smfc;
+};
+
 struct csi_priv {
 	struct device *dev;
 	struct ipu_soc *ipu;
@@ -65,6 +79,7 @@ struct csi_priv {
 	const struct imx_media_pixfmt *cc[CSI_NUM_PADS];
 	struct v4l2_fract frame_interval;
 	struct v4l2_rect crop;
+	const struct csi_skip_desc *skip[CSI_NUM_PADS - 1];
 
 	/* active vb2 buffers to send to video dev sink */
 	struct imx_media_buffer *active_vb2_buf[2];
@@ -517,10 +532,12 @@ static int csi_setup(struct csi_priv *priv)
 	struct v4l2_mbus_config sensor_mbus_cfg;
 	struct v4l2_of_endpoint *sensor_ep;
 	struct v4l2_mbus_framefmt if_fmt;
+	const struct csi_skip_desc *skip;
 
 	infmt = &priv->format_mbus[CSI_SINK_PAD];
 	outfmt = &priv->format_mbus[priv->active_output_pad];
 	sensor_ep = &priv->sensor->sensor_ep;
+	skip = priv->skip[priv->active_output_pad - 1];
 
 	/* compose mbus_config from sensor endpoint */
 	sensor_mbus_cfg.type = sensor_ep->bus_type;
@@ -545,6 +562,9 @@ static int csi_setup(struct csi_priv *priv)
 
 	ipu_csi_set_dest(priv->csi, priv->dest);
 
+	ipu_csi_set_skip_smfc(priv->csi, skip->skip_smfc, skip->max_ratio - 1,
+			      0);
+
 	ipu_csi_dump(priv->csi);
 
 	return 0;
@@ -608,6 +628,77 @@ static void csi_stop(struct csi_priv *priv)
 	ipu_csi_disable(priv->csi);
 }
 
+static const struct csi_skip_desc csi_skip[12] = {
+	{ 1, 1, 0x00 }, /* Keep all frames */
+	{ 5, 6, 0x10 }, /* Skip every sixth frame */
+	{ 4, 5, 0x08 }, /* Skip every fifth frame */
+	{ 3, 4, 0x04 }, /* Skip every fourth frame */
+	{ 2, 3, 0x02 }, /* Skip every third frame */
+	{ 3, 5, 0x0a }, /* Skip frames 1 and 3 of every 5 */
+	{ 1, 2, 0x01 }, /* Skip every second frame */
+	{ 2, 5, 0x0b }, /* Keep frames 1 and 4 of every 5 */
+	{ 1, 3, 0x03 }, /* Keep one in three frames */
+	{ 1, 4, 0x07 }, /* Keep one in four frames */
+	{ 1, 5, 0x0f }, /* Keep one in five frames */
+	{ 1, 6, 0x1f }, /* Keep one in six frames */
+};
+
+static void csi_apply_skip_interval(const struct csi_skip_desc *skip,
+				    struct v4l2_fract *interval)
+{
+	unsigned int div;
+
+	interval->numerator *= skip->max_ratio;
+	interval->denominator *= skip->keep;
+
+	/* Reduce fraction to lowest terms */
+	div = gcd(interval->numerator, interval->denominator);
+	if (div > 1) {
+		interval->numerator /= div;
+		interval->denominator /= div;
+	}
+}
+
+/*
+ * Find the skip pattern to produce the output frame interval closest to the
+ * requested one, for the given input frame interval. Updates the output frame
+ * interval to the exact value.
+ */
+static const struct csi_skip_desc *csi_find_best_skip(struct v4l2_fract *in,
+						      struct v4l2_fract *out)
+{
+	const struct csi_skip_desc *skip = &csi_skip[0], *best_skip = skip;
+	u32 min_err = UINT_MAX;
+	u64 want_us;
+	int i;
+
+	/* Default to 1:1 ratio */
+	if (out->numerator == 0 || out->denominator == 0 ||
+	    in->numerator == 0 || in->denominator == 0)
+		return best_skip;
+
+	want_us = div_u64((u64)USEC_PER_SEC * out->numerator, out->denominator);
+
+	/* Find the reduction closest to the requested time per frame */
+	for (i = 0; i < ARRAY_SIZE(csi_skip); i++, skip++) {
+		u64 tmp, err;
+
+		tmp = div_u64((u64)USEC_PER_SEC * in->numerator *
+			      skip->max_ratio, in->denominator * skip->keep);
+
+		err = abs((s64)tmp - want_us);
+		if (err < min_err) {
+			min_err = err;
+			best_skip = skip;
+		}
+	}
+
+	*out = *in;
+	csi_apply_skip_interval(best_skip, out);
+
+	return best_skip;
+}
+
 /*
  * V4L2 subdev operations.
  */
@@ -617,8 +708,16 @@ static int csi_g_frame_interval(struct v4l2_subdev *sd,
 {
 	struct csi_priv *priv = v4l2_get_subdevdata(sd);
 
+	if (fi->pad >= CSI_NUM_PADS)
+		return -EINVAL;
+
 	mutex_lock(&priv->lock);
+
 	fi->interval = priv->frame_interval;
+
+	if (fi->pad != CSI_SINK_PAD)
+		csi_apply_skip_interval(priv->skip[fi->pad - 1], &fi->interval);
+
 	mutex_unlock(&priv->lock);
 
 	return 0;
@@ -629,14 +728,27 @@ static int csi_s_frame_interval(struct v4l2_subdev *sd,
 {
 	struct csi_priv *priv = v4l2_get_subdevdata(sd);
 
+	if (fi->pad >= CSI_NUM_PADS)
+		return -EINVAL;
+
 	mutex_lock(&priv->lock);
 
-	/* Output pads mirror active input pad, no limits on input pads */
-	if (fi->pad == CSI_SRC_PAD_IDMAC || fi->pad == CSI_SRC_PAD_DIRECT)
-		fi->interval = priv->frame_interval;
+	/* No limits on input pad */
+	if (fi->pad == CSI_SINK_PAD) {
+		priv->frame_interval = fi->interval;
+
+		/* Reset frame skipping ratio to 1:1 */
+		priv->skip[0] = &csi_skip[0];
+		priv->skip[1] = &csi_skip[0];
 
-	priv->frame_interval = fi->interval;
+		goto out;
+	}
+
+	/* Output pads depend on input interval, modified by frame skipping */
+	priv->skip[fi->pad - 1] = csi_find_best_skip(&priv->frame_interval,
+						     &fi->interval);
 
+out:
 	mutex_unlock(&priv->lock);
 
 	return 0;
@@ -1256,6 +1368,9 @@ static int csi_registered(struct v4l2_subdev *sd)
 					      &priv->cc[i]);
 		if (ret)
 			goto put_csi;
+		/* disable frame skipping */
+		if (i != CSI_SINK_PAD)
+			priv->skip[i - 1] = &csi_skip[0];
 	}
 
 	/* init default frame interval */
-- 
2.7.4

[PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Steve Longerbeam]

From: Philipp Zabel <p.zabel@pengutronix.de>

The csi_try_crop call in set_fmt should compare the cropping rectangle
to the currently set input format, not to the previous input format.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/imx-media-csi.c | 11 +++++------
 1 file changed, 5 insertions(+), 6 deletions(-)

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index e5105ec..cf070be 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -989,13 +989,11 @@ __csi_get_fmt(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
 static int csi_try_crop(struct csi_priv *priv,
 			struct v4l2_rect *crop,
 			struct v4l2_subdev_pad_config *cfg,
-			enum v4l2_subdev_format_whence which,
+			struct v4l2_mbus_framefmt *infmt,
 			struct imx_media_subdev *sensor)
 {
 	struct v4l2_of_endpoint *sensor_ep;
-	struct v4l2_mbus_framefmt *infmt;
 
-	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, which);
 	sensor_ep = &sensor->sensor_ep;
 
 	crop->width = min_t(__u32, infmt->width, crop->width);
@@ -1178,8 +1176,7 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 		crop.top = 0;
 		crop.width = sdformat->format.width;
 		crop.height = sdformat->format.height;
-		ret = csi_try_crop(priv, &crop, cfg,
-				   sdformat->which, sensor);
+		ret = csi_try_crop(priv, &crop, cfg, &sdformat->format, sensor);
 		if (ret)
 			goto out;
 
@@ -1263,6 +1260,7 @@ static int csi_set_selection(struct v4l2_subdev *sd,
 			     struct v4l2_subdev_selection *sel)
 {
 	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_mbus_framefmt *infmt;
 	struct imx_media_subdev *sensor;
 	int ret = 0;
 
@@ -1296,7 +1294,8 @@ static int csi_set_selection(struct v4l2_subdev *sd,
 		goto out;
 	}
 
-	ret = csi_try_crop(priv, &sel->r, cfg, sel->which, sensor);
+	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
+	ret = csi_try_crop(priv, &sel->r, cfg, infmt, sensor);
 	if (ret)
 		goto out;
 
-- 
2.7.4

[PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Steve Longerbeam]

From: Philipp Zabel <p.zabel@pengutronix.de>

The csi_try_crop call in set_fmt should compare the cropping rectangle
to the currently set input format, not to the previous input format.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/imx-media-csi.c | 11 +++++------
 1 file changed, 5 insertions(+), 6 deletions(-)

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index e5105ec..cf070be 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -989,13 +989,11 @@ __csi_get_fmt(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
 static int csi_try_crop(struct csi_priv *priv,
 			struct v4l2_rect *crop,
 			struct v4l2_subdev_pad_config *cfg,
-			enum v4l2_subdev_format_whence which,
+			struct v4l2_mbus_framefmt *infmt,
 			struct imx_media_subdev *sensor)
 {
 	struct v4l2_of_endpoint *sensor_ep;
-	struct v4l2_mbus_framefmt *infmt;
 
-	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, which);
 	sensor_ep = &sensor->sensor_ep;
 
 	crop->width = min_t(__u32, infmt->width, crop->width);
@@ -1178,8 +1176,7 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 		crop.top = 0;
 		crop.width = sdformat->format.width;
 		crop.height = sdformat->format.height;
-		ret = csi_try_crop(priv, &crop, cfg,
-				   sdformat->which, sensor);
+		ret = csi_try_crop(priv, &crop, cfg, &sdformat->format, sensor);
 		if (ret)
 			goto out;
 
@@ -1263,6 +1260,7 @@ static int csi_set_selection(struct v4l2_subdev *sd,
 			     struct v4l2_subdev_selection *sel)
 {
 	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_mbus_framefmt *infmt;
 	struct imx_media_subdev *sensor;
 	int ret = 0;
 
@@ -1296,7 +1294,8 @@ static int csi_set_selection(struct v4l2_subdev *sd,
 		goto out;
 	}
 
-	ret = csi_try_crop(priv, &sel->r, cfg, sel->which, sensor);
+	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
+	ret = csi_try_crop(priv, &sel->r, cfg, infmt, sensor);
 	if (ret)
 		goto out;
 
-- 
2.7.4

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Russell King - ARM Linux]

On Thu, Mar 09, 2017 at 08:53:18PM -0800, Steve Longerbeam wrote:
> From: Philipp Zabel <p.zabel@pengutronix.de>
> 
> The csi_try_crop call in set_fmt should compare the cropping rectangle
> to the currently set input format, not to the previous input format.

Are we really sure that the cropping support is implemented correctly?

I came across this while looking at what we're doing with the
V4L2_SEL_FLAG_KEEP_CONFIG flag.

Documentation/media/uapi/v4l/dev-subdev.rst defines the behaviour of
the user API, and "Order of configuration and format propagation" says:

  The coordinates to a step always refer to the actual size of the
  previous step. The exception to this rule is the source compose
  rectangle, which refers to the sink compose bounds rectangle --- if it
  is supported by the hardware.
  
  1. Sink pad format. The user configures the sink pad format. This format
     defines the parameters of the image the entity receives through the
     pad for further processing.
  
  2. Sink pad actual crop selection. The sink pad crop defines the crop
     performed to the sink pad format.
  
  3. Sink pad actual compose selection. The size of the sink pad compose
     rectangle defines the scaling ratio compared to the size of the sink
     pad crop rectangle. The location of the compose rectangle specifies
     the location of the actual sink compose rectangle in the sink compose
     bounds rectangle.
  
  4. Source pad actual crop selection. Crop on the source pad defines crop
     performed to the image in the sink compose bounds rectangle.
  
  5. Source pad format. The source pad format defines the output pixel
     format of the subdev, as well as the other parameters with the
     exception of the image width and height. Width and height are defined
     by the size of the source pad actual crop selection.
  
  Accessing any of the above rectangles not supported by the subdev will
  return ``EINVAL``. Any rectangle referring to a previous unsupported
  rectangle coordinates will instead refer to the previous supported
  rectangle. For example, if sink crop is not supported, the compose
  selection will refer to the sink pad format dimensions instead.

Note step 3 above: scaling is defined by the ratio of the _sink_ crop
rectangle to the _sink_ compose rectangle.

So, lets say that the camera produces a 1280x720 image, and the sink
pad format is configured with 1280x720.  That's step 1.

The sink crop operates within that rectangle, cropping it to an area.
Let's say we're only interested in its centre, so we'd chose 640x360
with the top-left as 320,180.  This is step 2.

Then, if we want to down-scale by a factor of two, we'd set the sink
compose selection to 320x180.

This seems to be at odds with how the scaling is done in CSI at
present: the selection implementations all reject attempts to
configure the sink pad, instead only supporting crop rectangles on
the source, and we use the source crop rectangle to define the
down-scaling.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Russell King - ARM Linux]

On Thu, Mar 09, 2017 at 08:53:18PM -0800, Steve Longerbeam wrote:
> From: Philipp Zabel <p.zabel@pengutronix.de>
> 
> The csi_try_crop call in set_fmt should compare the cropping rectangle
> to the currently set input format, not to the previous input format.

Are we really sure that the cropping support is implemented correctly?

I came across this while looking at what we're doing with the
V4L2_SEL_FLAG_KEEP_CONFIG flag.

Documentation/media/uapi/v4l/dev-subdev.rst defines the behaviour of
the user API, and "Order of configuration and format propagation" says:

  The coordinates to a step always refer to the actual size of the
  previous step. The exception to this rule is the source compose
  rectangle, which refers to the sink compose bounds rectangle --- if it
  is supported by the hardware.
  
  1. Sink pad format. The user configures the sink pad format. This format
     defines the parameters of the image the entity receives through the
     pad for further processing.
  
  2. Sink pad actual crop selection. The sink pad crop defines the crop
     performed to the sink pad format.
  
  3. Sink pad actual compose selection. The size of the sink pad compose
     rectangle defines the scaling ratio compared to the size of the sink
     pad crop rectangle. The location of the compose rectangle specifies
     the location of the actual sink compose rectangle in the sink compose
     bounds rectangle.
  
  4. Source pad actual crop selection. Crop on the source pad defines crop
     performed to the image in the sink compose bounds rectangle.
  
  5. Source pad format. The source pad format defines the output pixel
     format of the subdev, as well as the other parameters with the
     exception of the image width and height. Width and height are defined
     by the size of the source pad actual crop selection.
  
  Accessing any of the above rectangles not supported by the subdev will
  return ``EINVAL``. Any rectangle referring to a previous unsupported
  rectangle coordinates will instead refer to the previous supported
  rectangle. For example, if sink crop is not supported, the compose
  selection will refer to the sink pad format dimensions instead.

Note step 3 above: scaling is defined by the ratio of the _sink_ crop
rectangle to the _sink_ compose rectangle.

So, lets say that the camera produces a 1280x720 image, and the sink
pad format is configured with 1280x720.  That's step 1.

The sink crop operates within that rectangle, cropping it to an area.
Let's say we're only interested in its centre, so we'd chose 640x360
with the top-left as 320,180.  This is step 2.

Then, if we want to down-scale by a factor of two, we'd set the sink
compose selection to 320x180.

This seems to be at odds with how the scaling is done in CSI at
present: the selection implementations all reject attempts to
configure the sink pad, instead only supporting crop rectangles on
the source, and we use the source crop rectangle to define the
down-scaling.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Russell King - ARM Linux]

On Thu, Mar 09, 2017 at 08:53:18PM -0800, Steve Longerbeam wrote:
> From: Philipp Zabel <p.zabel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
> 
> The csi_try_crop call in set_fmt should compare the cropping rectangle
> to the currently set input format, not to the previous input format.

Are we really sure that the cropping support is implemented correctly?

I came across this while looking at what we're doing with the
V4L2_SEL_FLAG_KEEP_CONFIG flag.

Documentation/media/uapi/v4l/dev-subdev.rst defines the behaviour of
the user API, and "Order of configuration and format propagation" says:

  The coordinates to a step always refer to the actual size of the
  previous step. The exception to this rule is the source compose
  rectangle, which refers to the sink compose bounds rectangle --- if it
  is supported by the hardware.
  
  1. Sink pad format. The user configures the sink pad format. This format
     defines the parameters of the image the entity receives through the
     pad for further processing.
  
  2. Sink pad actual crop selection. The sink pad crop defines the crop
     performed to the sink pad format.
  
  3. Sink pad actual compose selection. The size of the sink pad compose
     rectangle defines the scaling ratio compared to the size of the sink
     pad crop rectangle. The location of the compose rectangle specifies
     the location of the actual sink compose rectangle in the sink compose
     bounds rectangle.
  
  4. Source pad actual crop selection. Crop on the source pad defines crop
     performed to the image in the sink compose bounds rectangle.
  
  5. Source pad format. The source pad format defines the output pixel
     format of the subdev, as well as the other parameters with the
     exception of the image width and height. Width and height are defined
     by the size of the source pad actual crop selection.
  
  Accessing any of the above rectangles not supported by the subdev will
  return ``EINVAL``. Any rectangle referring to a previous unsupported
  rectangle coordinates will instead refer to the previous supported
  rectangle. For example, if sink crop is not supported, the compose
  selection will refer to the sink pad format dimensions instead.

Note step 3 above: scaling is defined by the ratio of the _sink_ crop
rectangle to the _sink_ compose rectangle.

So, lets say that the camera produces a 1280x720 image, and the sink
pad format is configured with 1280x720.  That's step 1.

The sink crop operates within that rectangle, cropping it to an area.
Let's say we're only interested in its centre, so we'd chose 640x360
with the top-left as 320,180.  This is step 2.

Then, if we want to down-scale by a factor of two, we'd set the sink
compose selection to 320x180.

This seems to be at odds with how the scaling is done in CSI at
present: the selection implementations all reject attempts to
configure the sink pad, instead only supporting crop rectangles on
the source, and we use the source crop rectangle to define the
down-scaling.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Steve Longerbeam]

On 03/19/2017 08:22 AM, Russell King - ARM Linux wrote:
> On Thu, Mar 09, 2017 at 08:53:18PM -0800, Steve Longerbeam wrote:
>> From: Philipp Zabel <p.zabel@pengutronix.de>
>>
>> The csi_try_crop call in set_fmt should compare the cropping rectangle
>> to the currently set input format, not to the previous input format.
> Are we really sure that the cropping support is implemented correctly?
>
> I came across this while looking at what we're doing with the
> V4L2_SEL_FLAG_KEEP_CONFIG flag.
>
> Documentation/media/uapi/v4l/dev-subdev.rst defines the behaviour of
> the user API, and "Order of configuration and format propagation" says:
>
>    The coordinates to a step always refer to the actual size of the
>    previous step. The exception to this rule is the source compose
>    rectangle, which refers to the sink compose bounds rectangle --- if it
>    is supported by the hardware.
>    
>    1. Sink pad format. The user configures the sink pad format. This format
>       defines the parameters of the image the entity receives through the
>       pad for further processing.
>    
>    2. Sink pad actual crop selection. The sink pad crop defines the crop
>       performed to the sink pad format.
>    
>    3. Sink pad actual compose selection. The size of the sink pad compose
>       rectangle defines the scaling ratio compared to the size of the sink
>       pad crop rectangle. The location of the compose rectangle specifies
>       the location of the actual sink compose rectangle in the sink compose
>       bounds rectangle.
>    
>    4. Source pad actual crop selection. Crop on the source pad defines crop
>       performed to the image in the sink compose bounds rectangle.
>    
>    5. Source pad format. The source pad format defines the output pixel
>       format of the subdev, as well as the other parameters with the
>       exception of the image width and height. Width and height are defined
>       by the size of the source pad actual crop selection.
>    
>    Accessing any of the above rectangles not supported by the subdev will
>    return ``EINVAL``. Any rectangle referring to a previous unsupported
>    rectangle coordinates will instead refer to the previous supported
>    rectangle. For example, if sink crop is not supported, the compose
>    selection will refer to the sink pad format dimensions instead.
>
> Note step 3 above: scaling is defined by the ratio of the _sink_ crop
> rectangle to the _sink_ compose rectangle.
>
> So, lets say that the camera produces a 1280x720 image, and the sink
> pad format is configured with 1280x720.  That's step 1.
>
> The sink crop operates within that rectangle, cropping it to an area.
> Let's say we're only interested in its centre, so we'd chose 640x360
> with the top-left as 320,180.  This is step 2.
>
> Then, if we want to down-scale by a factor of two, we'd set the sink
> compose selection to 320x180.
>
> This seems to be at odds with how the scaling is done in CSI at
> present: the selection implementations all reject attempts to
> configure the sink pad, instead only supporting crop rectangles on
> the source,

Correct. Currently cropping is only supported at the source pad
(step 4).

Initially the CSI didn't support down-scaling, so step 3 is not supported,
so the sink pad format/crop selection rectangle/crop compose rectangle
are collapsed into the same sink pad format rectangle.

Philipp later added support for /2 downscaling, but we didn't put this in
the correct API, looks like this needs to move into the selection API at
step 3 (sink pad compose rectangle).


>   and we use the source crop rectangle to define the
> down-scaling.

Yes. And maybe there is nothing wrong with that, because scaling is also
defined by the source/sink _format_ ratios (if I'm not mistaken), so looking
at this another way, we're just defining scaling in the CSI via another
legal API.


Steve

[PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Steve Longerbeam]

On 03/19/2017 08:22 AM, Russell King - ARM Linux wrote:
> On Thu, Mar 09, 2017 at 08:53:18PM -0800, Steve Longerbeam wrote:
>> From: Philipp Zabel <p.zabel@pengutronix.de>
>>
>> The csi_try_crop call in set_fmt should compare the cropping rectangle
>> to the currently set input format, not to the previous input format.
> Are we really sure that the cropping support is implemented correctly?
>
> I came across this while looking at what we're doing with the
> V4L2_SEL_FLAG_KEEP_CONFIG flag.
>
> Documentation/media/uapi/v4l/dev-subdev.rst defines the behaviour of
> the user API, and "Order of configuration and format propagation" says:
>
>    The coordinates to a step always refer to the actual size of the
>    previous step. The exception to this rule is the source compose
>    rectangle, which refers to the sink compose bounds rectangle --- if it
>    is supported by the hardware.
>    
>    1. Sink pad format. The user configures the sink pad format. This format
>       defines the parameters of the image the entity receives through the
>       pad for further processing.
>    
>    2. Sink pad actual crop selection. The sink pad crop defines the crop
>       performed to the sink pad format.
>    
>    3. Sink pad actual compose selection. The size of the sink pad compose
>       rectangle defines the scaling ratio compared to the size of the sink
>       pad crop rectangle. The location of the compose rectangle specifies
>       the location of the actual sink compose rectangle in the sink compose
>       bounds rectangle.
>    
>    4. Source pad actual crop selection. Crop on the source pad defines crop
>       performed to the image in the sink compose bounds rectangle.
>    
>    5. Source pad format. The source pad format defines the output pixel
>       format of the subdev, as well as the other parameters with the
>       exception of the image width and height. Width and height are defined
>       by the size of the source pad actual crop selection.
>    
>    Accessing any of the above rectangles not supported by the subdev will
>    return ``EINVAL``. Any rectangle referring to a previous unsupported
>    rectangle coordinates will instead refer to the previous supported
>    rectangle. For example, if sink crop is not supported, the compose
>    selection will refer to the sink pad format dimensions instead.
>
> Note step 3 above: scaling is defined by the ratio of the _sink_ crop
> rectangle to the _sink_ compose rectangle.
>
> So, lets say that the camera produces a 1280x720 image, and the sink
> pad format is configured with 1280x720.  That's step 1.
>
> The sink crop operates within that rectangle, cropping it to an area.
> Let's say we're only interested in its centre, so we'd chose 640x360
> with the top-left as 320,180.  This is step 2.
>
> Then, if we want to down-scale by a factor of two, we'd set the sink
> compose selection to 320x180.
>
> This seems to be at odds with how the scaling is done in CSI at
> present: the selection implementations all reject attempts to
> configure the sink pad, instead only supporting crop rectangles on
> the source,

Correct. Currently cropping is only supported at the source pad
(step 4).

Initially the CSI didn't support down-scaling, so step 3 is not supported,
so the sink pad format/crop selection rectangle/crop compose rectangle
are collapsed into the same sink pad format rectangle.

Philipp later added support for /2 downscaling, but we didn't put this in
the correct API, looks like this needs to move into the selection API at
step 3 (sink pad compose rectangle).


>   and we use the source crop rectangle to define the
> down-scaling.

Yes. And maybe there is nothing wrong with that, because scaling is also
defined by the source/sink _format_ ratios (if I'm not mistaken), so looking
at this another way, we're just defining scaling in the CSI via another
legal API.


Steve

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Steve Longerbeam]

On 03/19/2017 08:22 AM, Russell King - ARM Linux wrote:
> On Thu, Mar 09, 2017 at 08:53:18PM -0800, Steve Longerbeam wrote:
>> From: Philipp Zabel <p.zabel@pengutronix.de>
>>
>> The csi_try_crop call in set_fmt should compare the cropping rectangle
>> to the currently set input format, not to the previous input format.
> Are we really sure that the cropping support is implemented correctly?
>
> I came across this while looking at what we're doing with the
> V4L2_SEL_FLAG_KEEP_CONFIG flag.
>
> Documentation/media/uapi/v4l/dev-subdev.rst defines the behaviour of
> the user API, and "Order of configuration and format propagation" says:
>
>    The coordinates to a step always refer to the actual size of the
>    previous step. The exception to this rule is the source compose
>    rectangle, which refers to the sink compose bounds rectangle --- if it
>    is supported by the hardware.
>    
>    1. Sink pad format. The user configures the sink pad format. This format
>       defines the parameters of the image the entity receives through the
>       pad for further processing.
>    
>    2. Sink pad actual crop selection. The sink pad crop defines the crop
>       performed to the sink pad format.
>    
>    3. Sink pad actual compose selection. The size of the sink pad compose
>       rectangle defines the scaling ratio compared to the size of the sink
>       pad crop rectangle. The location of the compose rectangle specifies
>       the location of the actual sink compose rectangle in the sink compose
>       bounds rectangle.
>    
>    4. Source pad actual crop selection. Crop on the source pad defines crop
>       performed to the image in the sink compose bounds rectangle.
>    
>    5. Source pad format. The source pad format defines the output pixel
>       format of the subdev, as well as the other parameters with the
>       exception of the image width and height. Width and height are defined
>       by the size of the source pad actual crop selection.
>    
>    Accessing any of the above rectangles not supported by the subdev will
>    return ``EINVAL``. Any rectangle referring to a previous unsupported
>    rectangle coordinates will instead refer to the previous supported
>    rectangle. For example, if sink crop is not supported, the compose
>    selection will refer to the sink pad format dimensions instead.
>
> Note step 3 above: scaling is defined by the ratio of the _sink_ crop
> rectangle to the _sink_ compose rectangle.
>
> So, lets say that the camera produces a 1280x720 image, and the sink
> pad format is configured with 1280x720.  That's step 1.
>
> The sink crop operates within that rectangle, cropping it to an area.
> Let's say we're only interested in its centre, so we'd chose 640x360
> with the top-left as 320,180.  This is step 2.
>
> Then, if we want to down-scale by a factor of two, we'd set the sink
> compose selection to 320x180.
>
> This seems to be at odds with how the scaling is done in CSI at
> present: the selection implementations all reject attempts to
> configure the sink pad, instead only supporting crop rectangles on
> the source,

Correct. Currently cropping is only supported at the source pad
(step 4).

Initially the CSI didn't support down-scaling, so step 3 is not supported,
so the sink pad format/crop selection rectangle/crop compose rectangle
are collapsed into the same sink pad format rectangle.

Philipp later added support for /2 downscaling, but we didn't put this in
the correct API, looks like this needs to move into the selection API at
step 3 (sink pad compose rectangle).


>   and we use the source crop rectangle to define the
> down-scaling.

Yes. And maybe there is nothing wrong with that, because scaling is also
defined by the source/sink _format_ ratios (if I'm not mistaken), so looking
at this another way, we're just defining scaling in the CSI via another
legal API.


Steve

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Philipp Zabel]

On Sun, 2017-03-19 at 12:08 -0700, Steve Longerbeam wrote:
> 
> On 03/19/2017 08:22 AM, Russell King - ARM Linux wrote:
> > On Thu, Mar 09, 2017 at 08:53:18PM -0800, Steve Longerbeam wrote:
> >> From: Philipp Zabel <p.zabel@pengutronix.de>
> >>
> >> The csi_try_crop call in set_fmt should compare the cropping rectangle
> >> to the currently set input format, not to the previous input format.
> > Are we really sure that the cropping support is implemented correctly?
> >
> > I came across this while looking at what we're doing with the
> > V4L2_SEL_FLAG_KEEP_CONFIG flag.
> >
> > Documentation/media/uapi/v4l/dev-subdev.rst defines the behaviour of
> > the user API, and "Order of configuration and format propagation" says:
> >
> >    The coordinates to a step always refer to the actual size of the
> >    previous step. The exception to this rule is the source compose
> >    rectangle, which refers to the sink compose bounds rectangle --- if it
> >    is supported by the hardware.
> >    
> >    1. Sink pad format. The user configures the sink pad format. This format
> >       defines the parameters of the image the entity receives through the
> >       pad for further processing.
> >    
> >    2. Sink pad actual crop selection. The sink pad crop defines the crop
> >       performed to the sink pad format.
> >    
> >    3. Sink pad actual compose selection. The size of the sink pad compose
> >       rectangle defines the scaling ratio compared to the size of the sink
> >       pad crop rectangle. The location of the compose rectangle specifies
> >       the location of the actual sink compose rectangle in the sink compose
> >       bounds rectangle.
> >    
> >    4. Source pad actual crop selection. Crop on the source pad defines crop
> >       performed to the image in the sink compose bounds rectangle.
> >    
> >    5. Source pad format. The source pad format defines the output pixel
> >       format of the subdev, as well as the other parameters with the
> >       exception of the image width and height. Width and height are defined
> >       by the size of the source pad actual crop selection.
> >    
> >    Accessing any of the above rectangles not supported by the subdev will
> >    return ``EINVAL``. Any rectangle referring to a previous unsupported
> >    rectangle coordinates will instead refer to the previous supported
> >    rectangle. For example, if sink crop is not supported, the compose
> >    selection will refer to the sink pad format dimensions instead.
> >
> > Note step 3 above: scaling is defined by the ratio of the _sink_ crop
> > rectangle to the _sink_ compose rectangle.

The above paragraph suggests we skip any rectangles that are not
supported. In our case that would be 3. and 4., since the CSI can't
compose into a larger frame. I hadn't realised that the crop selection
currently happens on the source pad.
The hardware actually only supports cropping of the input (the crop
rectangle we write into the window registers are before downscaling). So
the crop rectangle should be moved to the sink pad.

> > So, lets say that the camera produces a 1280x720 image, and the sink
> > pad format is configured with 1280x720.  That's step 1.
> >
> > The sink crop operates within that rectangle, cropping it to an area.
> > Let's say we're only interested in its centre, so we'd chose 640x360
> > with the top-left as 320,180.  This is step 2.
>>
> > Then, if we want to down-scale by a factor of two, we'd set the sink
> > compose selection to 320x180.

Except when composing is not supported. If the sink compose and source
crop rectangles are not supported, the source pad format takes their
place in determining the scaling output resolution. At least that's how
I read the documentation.

> > This seems to be at odds with how the scaling is done in CSI at
> > present: the selection implementations all reject attempts to
> > configure the sink pad, instead only supporting crop rectangles on
> > the source,
> 
> Correct. Currently cropping is only supported at the source pad
> (step 4).
> 
> Initially the CSI didn't support down-scaling, so step 3 is not supported,
> so the sink pad format/crop selection rectangle/crop compose rectangle
> are collapsed into the same sink pad format rectangle.
> 
> Philipp later added support for /2 downscaling, but we didn't put this in
> the correct API, looks like this needs to move into the selection API at
> step 3 (sink pad compose rectangle).

I am not sure about this. Wouldn't moving the input crop to the sink pad
be enough? If we added support for the sink pad compose rectangle, that
wouldn't actually allow to compose the CSI output into a larger frame.
Since the subdevice can't compose, I'd leave the sink compose rectangle
disabled.

> >   and we use the source crop rectangle to define the
> > down-scaling.

We use the source pad format to define the downscaling relative to the
source crop rectangle (which is wrong, it should be relative to the sink
crop rectangle).

> Yes. And maybe there is nothing wrong with that, because scaling is also
> defined by the source/sink _format_ ratios (if I'm not mistaken), so looking
> at this another way, we're just defining scaling in the CSI via another
> legal API.

I didn't touch the crop rectangle at all, just setting the input
resolution on the sink pad and the desired output resolution on the
source pad should work.

regards
Philipp

[PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Philipp Zabel]

On Sun, 2017-03-19 at 12:08 -0700, Steve Longerbeam wrote:
> 
> On 03/19/2017 08:22 AM, Russell King - ARM Linux wrote:
> > On Thu, Mar 09, 2017 at 08:53:18PM -0800, Steve Longerbeam wrote:
> >> From: Philipp Zabel <p.zabel@pengutronix.de>
> >>
> >> The csi_try_crop call in set_fmt should compare the cropping rectangle
> >> to the currently set input format, not to the previous input format.
> > Are we really sure that the cropping support is implemented correctly?
> >
> > I came across this while looking at what we're doing with the
> > V4L2_SEL_FLAG_KEEP_CONFIG flag.
> >
> > Documentation/media/uapi/v4l/dev-subdev.rst defines the behaviour of
> > the user API, and "Order of configuration and format propagation" says:
> >
> >    The coordinates to a step always refer to the actual size of the
> >    previous step. The exception to this rule is the source compose
> >    rectangle, which refers to the sink compose bounds rectangle --- if it
> >    is supported by the hardware.
> >    
> >    1. Sink pad format. The user configures the sink pad format. This format
> >       defines the parameters of the image the entity receives through the
> >       pad for further processing.
> >    
> >    2. Sink pad actual crop selection. The sink pad crop defines the crop
> >       performed to the sink pad format.
> >    
> >    3. Sink pad actual compose selection. The size of the sink pad compose
> >       rectangle defines the scaling ratio compared to the size of the sink
> >       pad crop rectangle. The location of the compose rectangle specifies
> >       the location of the actual sink compose rectangle in the sink compose
> >       bounds rectangle.
> >    
> >    4. Source pad actual crop selection. Crop on the source pad defines crop
> >       performed to the image in the sink compose bounds rectangle.
> >    
> >    5. Source pad format. The source pad format defines the output pixel
> >       format of the subdev, as well as the other parameters with the
> >       exception of the image width and height. Width and height are defined
> >       by the size of the source pad actual crop selection.
> >    
> >    Accessing any of the above rectangles not supported by the subdev will
> >    return ``EINVAL``. Any rectangle referring to a previous unsupported
> >    rectangle coordinates will instead refer to the previous supported
> >    rectangle. For example, if sink crop is not supported, the compose
> >    selection will refer to the sink pad format dimensions instead.
> >
> > Note step 3 above: scaling is defined by the ratio of the _sink_ crop
> > rectangle to the _sink_ compose rectangle.

The above paragraph suggests we skip any rectangles that are not
supported. In our case that would be 3. and 4., since the CSI can't
compose into a larger frame. I hadn't realised that the crop selection
currently happens on the source pad.
The hardware actually only supports cropping of the input (the crop
rectangle we write into the window registers are before downscaling). So
the crop rectangle should be moved to the sink pad.

> > So, lets say that the camera produces a 1280x720 image, and the sink
> > pad format is configured with 1280x720.  That's step 1.
> >
> > The sink crop operates within that rectangle, cropping it to an area.
> > Let's say we're only interested in its centre, so we'd chose 640x360
> > with the top-left as 320,180.  This is step 2.
>>
> > Then, if we want to down-scale by a factor of two, we'd set the sink
> > compose selection to 320x180.

Except when composing is not supported. If the sink compose and source
crop rectangles are not supported, the source pad format takes their
place in determining the scaling output resolution. At least that's how
I read the documentation.

> > This seems to be at odds with how the scaling is done in CSI at
> > present: the selection implementations all reject attempts to
> > configure the sink pad, instead only supporting crop rectangles on
> > the source,
> 
> Correct. Currently cropping is only supported at the source pad
> (step 4).
> 
> Initially the CSI didn't support down-scaling, so step 3 is not supported,
> so the sink pad format/crop selection rectangle/crop compose rectangle
> are collapsed into the same sink pad format rectangle.
> 
> Philipp later added support for /2 downscaling, but we didn't put this in
> the correct API, looks like this needs to move into the selection API at
> step 3 (sink pad compose rectangle).

I am not sure about this. Wouldn't moving the input crop to the sink pad
be enough? If we added support for the sink pad compose rectangle, that
wouldn't actually allow to compose the CSI output into a larger frame.
Since the subdevice can't compose, I'd leave the sink compose rectangle
disabled.

> >   and we use the source crop rectangle to define the
> > down-scaling.

We use the source pad format to define the downscaling relative to the
source crop rectangle (which is wrong, it should be relative to the sink
crop rectangle).

> Yes. And maybe there is nothing wrong with that, because scaling is also
> defined by the source/sink _format_ ratios (if I'm not mistaken), so looking
> at this another way, we're just defining scaling in the CSI via another
> legal API.

I didn't touch the crop rectangle at all, just setting the input
resolution on the sink pad and the desired output resolution on the
source pad should work.

regards
Philipp

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Philipp Zabel]

On Sun, 2017-03-19 at 12:08 -0700, Steve Longerbeam wrote:
> 
> On 03/19/2017 08:22 AM, Russell King - ARM Linux wrote:
> > On Thu, Mar 09, 2017 at 08:53:18PM -0800, Steve Longerbeam wrote:
> >> From: Philipp Zabel <p.zabel@pengutronix.de>
> >>
> >> The csi_try_crop call in set_fmt should compare the cropping rectangle
> >> to the currently set input format, not to the previous input format.
> > Are we really sure that the cropping support is implemented correctly?
> >
> > I came across this while looking at what we're doing with the
> > V4L2_SEL_FLAG_KEEP_CONFIG flag.
> >
> > Documentation/media/uapi/v4l/dev-subdev.rst defines the behaviour of
> > the user API, and "Order of configuration and format propagation" says:
> >
> >    The coordinates to a step always refer to the actual size of the
> >    previous step. The exception to this rule is the source compose
> >    rectangle, which refers to the sink compose bounds rectangle --- if it
> >    is supported by the hardware.
> >    
> >    1. Sink pad format. The user configures the sink pad format. This format
> >       defines the parameters of the image the entity receives through the
> >       pad for further processing.
> >    
> >    2. Sink pad actual crop selection. The sink pad crop defines the crop
> >       performed to the sink pad format.
> >    
> >    3. Sink pad actual compose selection. The size of the sink pad compose
> >       rectangle defines the scaling ratio compared to the size of the sink
> >       pad crop rectangle. The location of the compose rectangle specifies
> >       the location of the actual sink compose rectangle in the sink compose
> >       bounds rectangle.
> >    
> >    4. Source pad actual crop selection. Crop on the source pad defines crop
> >       performed to the image in the sink compose bounds rectangle.
> >    
> >    5. Source pad format. The source pad format defines the output pixel
> >       format of the subdev, as well as the other parameters with the
> >       exception of the image width and height. Width and height are defined
> >       by the size of the source pad actual crop selection.
> >    
> >    Accessing any of the above rectangles not supported by the subdev will
> >    return ``EINVAL``. Any rectangle referring to a previous unsupported
> >    rectangle coordinates will instead refer to the previous supported
> >    rectangle. For example, if sink crop is not supported, the compose
> >    selection will refer to the sink pad format dimensions instead.
> >
> > Note step 3 above: scaling is defined by the ratio of the _sink_ crop
> > rectangle to the _sink_ compose rectangle.

The above paragraph suggests we skip any rectangles that are not
supported. In our case that would be 3. and 4., since the CSI can't
compose into a larger frame. I hadn't realised that the crop selection
currently happens on the source pad.
The hardware actually only supports cropping of the input (the crop
rectangle we write into the window registers are before downscaling). So
the crop rectangle should be moved to the sink pad.

> > So, lets say that the camera produces a 1280x720 image, and the sink
> > pad format is configured with 1280x720.  That's step 1.
> >
> > The sink crop operates within that rectangle, cropping it to an area.
> > Let's say we're only interested in its centre, so we'd chose 640x360
> > with the top-left as 320,180.  This is step 2.
>>
> > Then, if we want to down-scale by a factor of two, we'd set the sink
> > compose selection to 320x180.

Except when composing is not supported. If the sink compose and source
crop rectangles are not supported, the source pad format takes their
place in determining the scaling output resolution. At least that's how
I read the documentation.

> > This seems to be at odds with how the scaling is done in CSI at
> > present: the selection implementations all reject attempts to
> > configure the sink pad, instead only supporting crop rectangles on
> > the source,
> 
> Correct. Currently cropping is only supported at the source pad
> (step 4).
> 
> Initially the CSI didn't support down-scaling, so step 3 is not supported,
> so the sink pad format/crop selection rectangle/crop compose rectangle
> are collapsed into the same sink pad format rectangle.
> 
> Philipp later added support for /2 downscaling, but we didn't put this in
> the correct API, looks like this needs to move into the selection API at
> step 3 (sink pad compose rectangle).

I am not sure about this. Wouldn't moving the input crop to the sink pad
be enough? If we added support for the sink pad compose rectangle, that
wouldn't actually allow to compose the CSI output into a larger frame.
Since the subdevice can't compose, I'd leave the sink compose rectangle
disabled.

> >   and we use the source crop rectangle to define the
> > down-scaling.

We use the source pad format to define the downscaling relative to the
source crop rectangle (which is wrong, it should be relative to the sink
crop rectangle).

> Yes. And maybe there is nothing wrong with that, because scaling is also
> defined by the source/sink _format_ ratios (if I'm not mistaken), so looking
> at this another way, we're just defining scaling in the CSI via another
> legal API.

I didn't touch the crop rectangle at all, just setting the input
resolution on the sink pad and the desired output resolution on the
source pad should work.

regards
Philipp

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 12:55:26PM +0100, Philipp Zabel wrote:
> The above paragraph suggests we skip any rectangles that are not
> supported. In our case that would be 3. and 4., since the CSI can't
> compose into a larger frame. I hadn't realised that the crop selection
> currently happens on the source pad.

I'd recommend viewing the documentation in its post-processed version,
because then you get the examples as pictures, and they say that a
picture is worth 1000 words.  See

  https://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/dev-subdev.html

There is almost an exact example of what we're trying to do - it's
figure 4.6.  Here, we have a sink pad with a cropping rectangle on
the input, which is then scaled to a composition rectangle (there's
no bounds rectangle, and it's specified that in such a case the
top,left of the composition rectangle will always be 0,0 - see quote
below).

Where it differs is that the example also supports source cropping
for two source pads.  We don't support that.

The same document says:

  Scaling support is optional. When supported by a subdev, the crop
  rectangle on the subdev's sink pad is scaled to the size configured
  using the
  :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
  using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
  subdev supports scaling but not composing, the top and left values are
  not used and must always be set to zero.

which in itself describes _exactly_ our hardware here as far as the
cropping and scaling the hardware supports.

> Except when composing is not supported. If the sink compose and source
> crop rectangles are not supported, the source pad format takes their
> place in determining the scaling output resolution. At least that's how
> I read the documentation.

This isn't how I read it.  Scaling is the relationship between the size
of the sink crop and sink compose rectangle.  Composition requires that
there be a composition bounds rectangle to define the composition space,
and the top,left of the composition rectangle be adjustable to place
the composition rectangle within that space.

The above quoted paragraph from the documentation backs up my view in
its final sentence - it doesn't say "if the subdev supports scaling
but not composing, there is no composition rectangle" but says that
there _is_ one but its top,left coordinates are always zero.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 12:55:26PM +0100, Philipp Zabel wrote:
> The above paragraph suggests we skip any rectangles that are not
> supported. In our case that would be 3. and 4., since the CSI can't
> compose into a larger frame. I hadn't realised that the crop selection
> currently happens on the source pad.

I'd recommend viewing the documentation in its post-processed version,
because then you get the examples as pictures, and they say that a
picture is worth 1000 words.  See

  https://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/dev-subdev.html

There is almost an exact example of what we're trying to do - it's
figure 4.6.  Here, we have a sink pad with a cropping rectangle on
the input, which is then scaled to a composition rectangle (there's
no bounds rectangle, and it's specified that in such a case the
top,left of the composition rectangle will always be 0,0 - see quote
below).

Where it differs is that the example also supports source cropping
for two source pads.  We don't support that.

The same document says:

  Scaling support is optional. When supported by a subdev, the crop
  rectangle on the subdev's sink pad is scaled to the size configured
  using the
  :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
  using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
  subdev supports scaling but not composing, the top and left values are
  not used and must always be set to zero.

which in itself describes _exactly_ our hardware here as far as the
cropping and scaling the hardware supports.

> Except when composing is not supported. If the sink compose and source
> crop rectangles are not supported, the source pad format takes their
> place in determining the scaling output resolution. At least that's how
> I read the documentation.

This isn't how I read it.  Scaling is the relationship between the size
of the sink crop and sink compose rectangle.  Composition requires that
there be a composition bounds rectangle to define the composition space,
and the top,left of the composition rectangle be adjustable to place
the composition rectangle within that space.

The above quoted paragraph from the documentation backs up my view in
its final sentence - it doesn't say "if the subdev supports scaling
but not composing, there is no composition rectangle" but says that
there _is_ one but its top,left coordinates are always zero.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 12:55:26PM +0100, Philipp Zabel wrote:
> The above paragraph suggests we skip any rectangles that are not
> supported. In our case that would be 3. and 4., since the CSI can't
> compose into a larger frame. I hadn't realised that the crop selection
> currently happens on the source pad.

I'd recommend viewing the documentation in its post-processed version,
because then you get the examples as pictures, and they say that a
picture is worth 1000 words.  See

  https://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/dev-subdev.html

There is almost an exact example of what we're trying to do - it's
figure 4.6.  Here, we have a sink pad with a cropping rectangle on
the input, which is then scaled to a composition rectangle (there's
no bounds rectangle, and it's specified that in such a case the
top,left of the composition rectangle will always be 0,0 - see quote
below).

Where it differs is that the example also supports source cropping
for two source pads.  We don't support that.

The same document says:

  Scaling support is optional. When supported by a subdev, the crop
  rectangle on the subdev's sink pad is scaled to the size configured
  using the
  :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
  using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
  subdev supports scaling but not composing, the top and left values are
  not used and must always be set to zero.

which in itself describes _exactly_ our hardware here as far as the
cropping and scaling the hardware supports.

> Except when composing is not supported. If the sink compose and source
> crop rectangles are not supported, the source pad format takes their
> place in determining the scaling output resolution. At least that's how
> I read the documentation.

This isn't how I read it.  Scaling is the relationship between the size
of the sink crop and sink compose rectangle.  Composition requires that
there be a composition bounds rectangle to define the composition space,
and the top,left of the composition rectangle be adjustable to place
the composition rectangle within that space.

The above quoted paragraph from the documentation backs up my view in
its final sentence - it doesn't say "if the subdev supports scaling
but not composing, there is no composition rectangle" but says that
there _is_ one but its top,left coordinates are always zero.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Philipp Zabel]

On Mon, 2017-03-20 at 12:08 +0000, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 12:55:26PM +0100, Philipp Zabel wrote:
> > The above paragraph suggests we skip any rectangles that are not
> > supported. In our case that would be 3. and 4., since the CSI can't
> > compose into a larger frame. I hadn't realised that the crop selection
> > currently happens on the source pad.
> 
> I'd recommend viewing the documentation in its post-processed version,
> because then you get the examples as pictures, and they say that a
> picture is worth 1000 words.  See
> 
>   https://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/dev-subdev.html
> 
> There is almost an exact example of what we're trying to do - it's
> figure 4.6.  Here, we have a sink pad with a cropping rectangle on
> the input, which is then scaled to a composition rectangle (there's
> no bounds rectangle, and it's specified that in such a case the
> top,left of the composition rectangle will always be 0,0 - see quote
> below).
> 
> Where it differs is that the example also supports source cropping
> for two source pads.  We don't support that.
>
> The same document says:
> 
>   Scaling support is optional. When supported by a subdev, the crop
>   rectangle on the subdev's sink pad is scaled to the size configured
>   using the
>   :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
>   using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
>   subdev supports scaling but not composing, the top and left values are
>   not used and must always be set to zero.

Right, this sentence does imply that when scaling is supported, there
must be a sink compose rectangle, even when composing is not.

I have previously set up scaling like this:

media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"

Does this mean, it should work like this instead?

media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
media-ctl --set-v4l2 "'ipu1_csi0':0[fmt:UYVY2X8/1920x1080@1/60,compose:(0,0)/960x540]"
media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"

I suppose setting the source pad format should not be allowed to modify
the sink compose rectangle.

regards
Philipp

[PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Philipp Zabel]

On Mon, 2017-03-20 at 12:08 +0000, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 12:55:26PM +0100, Philipp Zabel wrote:
> > The above paragraph suggests we skip any rectangles that are not
> > supported. In our case that would be 3. and 4., since the CSI can't
> > compose into a larger frame. I hadn't realised that the crop selection
> > currently happens on the source pad.
> 
> I'd recommend viewing the documentation in its post-processed version,
> because then you get the examples as pictures, and they say that a
> picture is worth 1000 words.  See
> 
>   https://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/dev-subdev.html
> 
> There is almost an exact example of what we're trying to do - it's
> figure 4.6.  Here, we have a sink pad with a cropping rectangle on
> the input, which is then scaled to a composition rectangle (there's
> no bounds rectangle, and it's specified that in such a case the
> top,left of the composition rectangle will always be 0,0 - see quote
> below).
> 
> Where it differs is that the example also supports source cropping
> for two source pads.  We don't support that.
>
> The same document says:
> 
>   Scaling support is optional. When supported by a subdev, the crop
>   rectangle on the subdev's sink pad is scaled to the size configured
>   using the
>   :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
>   using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
>   subdev supports scaling but not composing, the top and left values are
>   not used and must always be set to zero.

Right, this sentence does imply that when scaling is supported, there
must be a sink compose rectangle, even when composing is not.

I have previously set up scaling like this:

media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080 at 1/60]"
media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540 at 1/30]"

Does this mean, it should work like this instead?

media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080 at 1/60]"
media-ctl --set-v4l2 "'ipu1_csi0':0[fmt:UYVY2X8/1920x1080 at 1/60,compose:(0,0)/960x540]"
media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540 at 1/30]"

I suppose setting the source pad format should not be allowed to modify
the sink compose rectangle.

regards
Philipp

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Philipp Zabel]

On Mon, 2017-03-20 at 12:08 +0000, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 12:55:26PM +0100, Philipp Zabel wrote:
> > The above paragraph suggests we skip any rectangles that are not
> > supported. In our case that would be 3. and 4., since the CSI can't
> > compose into a larger frame. I hadn't realised that the crop selection
> > currently happens on the source pad.
> 
> I'd recommend viewing the documentation in its post-processed version,
> because then you get the examples as pictures, and they say that a
> picture is worth 1000 words.  See
> 
>   https://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/dev-subdev.html
> 
> There is almost an exact example of what we're trying to do - it's
> figure 4.6.  Here, we have a sink pad with a cropping rectangle on
> the input, which is then scaled to a composition rectangle (there's
> no bounds rectangle, and it's specified that in such a case the
> top,left of the composition rectangle will always be 0,0 - see quote
> below).
> 
> Where it differs is that the example also supports source cropping
> for two source pads.  We don't support that.
>
> The same document says:
> 
>   Scaling support is optional. When supported by a subdev, the crop
>   rectangle on the subdev's sink pad is scaled to the size configured
>   using the
>   :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
>   using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
>   subdev supports scaling but not composing, the top and left values are
>   not used and must always be set to zero.

Right, this sentence does imply that when scaling is supported, there
must be a sink compose rectangle, even when composing is not.

I have previously set up scaling like this:

media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"

Does this mean, it should work like this instead?

media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
media-ctl --set-v4l2 "'ipu1_csi0':0[fmt:UYVY2X8/1920x1080@1/60,compose:(0,0)/960x540]"
media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"

I suppose setting the source pad format should not be allowed to modify
the sink compose rectangle.

regards
Philipp

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 03:00:51PM +0100, Philipp Zabel wrote:
> On Mon, 2017-03-20 at 12:08 +0000, Russell King - ARM Linux wrote:
> > The same document says:
> > 
> >   Scaling support is optional. When supported by a subdev, the crop
> >   rectangle on the subdev's sink pad is scaled to the size configured
> >   using the
> >   :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
> >   using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
> >   subdev supports scaling but not composing, the top and left values are
> >   not used and must always be set to zero.
> 
> Right, this sentence does imply that when scaling is supported, there
> must be a sink compose rectangle, even when composing is not.
> 
> I have previously set up scaling like this:
> 
> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
> 
> Does this mean, it should work like this instead?
> 
> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> media-ctl --set-v4l2 "'ipu1_csi0':0[fmt:UYVY2X8/1920x1080@1/60,compose:(0,0)/960x540]"
> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
> 
> I suppose setting the source pad format should not be allowed to modify
> the sink compose rectangle.

That is what I believe having read these documents several times, but
we need v4l2 people to confirm.

Note that setting the format on 'ipu1_csi0':0 should already be done by
the previous media-ctl command, so it should be possible to simplify
that to:

media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
media-ctl --set-v4l2 "'ipu1_csi0':0[compose:(0,0)/960x540]"
media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"

I have tripped over a bug in media-ctl when specifying both a crop and
compose rectangle - the --help output suggests that "," should be used
to separate them.  media-ctl rejects that, telling me the character at
the "," should be "]".  Replacing the "," with " " allows media-ctl to
accept it and set both rectangles, so it sounds like a parser bug - I've
not looked into this any further yet.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 03:00:51PM +0100, Philipp Zabel wrote:
> On Mon, 2017-03-20 at 12:08 +0000, Russell King - ARM Linux wrote:
> > The same document says:
> > 
> >   Scaling support is optional. When supported by a subdev, the crop
> >   rectangle on the subdev's sink pad is scaled to the size configured
> >   using the
> >   :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
> >   using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
> >   subdev supports scaling but not composing, the top and left values are
> >   not used and must always be set to zero.
> 
> Right, this sentence does imply that when scaling is supported, there
> must be a sink compose rectangle, even when composing is not.
> 
> I have previously set up scaling like this:
> 
> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080 at 1/60]"
> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540 at 1/30]"
> 
> Does this mean, it should work like this instead?
> 
> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080 at 1/60]"
> media-ctl --set-v4l2 "'ipu1_csi0':0[fmt:UYVY2X8/1920x1080 at 1/60,compose:(0,0)/960x540]"
> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540 at 1/30]"
> 
> I suppose setting the source pad format should not be allowed to modify
> the sink compose rectangle.

That is what I believe having read these documents several times, but
we need v4l2 people to confirm.

Note that setting the format on 'ipu1_csi0':0 should already be done by
the previous media-ctl command, so it should be possible to simplify
that to:

media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080 at 1/60]"
media-ctl --set-v4l2 "'ipu1_csi0':0[compose:(0,0)/960x540]"
media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540 at 1/30]"

I have tripped over a bug in media-ctl when specifying both a crop and
compose rectangle - the --help output suggests that "," should be used
to separate them.  media-ctl rejects that, telling me the character at
the "," should be "]".  Replacing the "," with " " allows media-ctl to
accept it and set both rectangles, so it sounds like a parser bug - I've
not looked into this any further yet.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 03:00:51PM +0100, Philipp Zabel wrote:
> On Mon, 2017-03-20 at 12:08 +0000, Russell King - ARM Linux wrote:
> > The same document says:
> > 
> >   Scaling support is optional. When supported by a subdev, the crop
> >   rectangle on the subdev's sink pad is scaled to the size configured
> >   using the
> >   :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
> >   using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
> >   subdev supports scaling but not composing, the top and left values are
> >   not used and must always be set to zero.
> 
> Right, this sentence does imply that when scaling is supported, there
> must be a sink compose rectangle, even when composing is not.
> 
> I have previously set up scaling like this:
> 
> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
> 
> Does this mean, it should work like this instead?
> 
> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> media-ctl --set-v4l2 "'ipu1_csi0':0[fmt:UYVY2X8/1920x1080@1/60,compose:(0,0)/960x540]"
> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
> 
> I suppose setting the source pad format should not be allowed to modify
> the sink compose rectangle.

That is what I believe having read these documents several times, but
we need v4l2 people to confirm.

Note that setting the format on 'ipu1_csi0':0 should already be done by
the previous media-ctl command, so it should be possible to simplify
that to:

media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
media-ctl --set-v4l2 "'ipu1_csi0':0[compose:(0,0)/960x540]"
media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"

I have tripped over a bug in media-ctl when specifying both a crop and
compose rectangle - the --help output suggests that "," should be used
to separate them.  media-ctl rejects that, telling me the character at
the "," should be "]".  Replacing the "," with " " allows media-ctl to
accept it and set both rectangles, so it sounds like a parser bug - I've
not looked into this any further yet.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 02:17:05PM +0000, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 03:00:51PM +0100, Philipp Zabel wrote:
> > On Mon, 2017-03-20 at 12:08 +0000, Russell King - ARM Linux wrote:
> > > The same document says:
> > > 
> > >   Scaling support is optional. When supported by a subdev, the crop
> > >   rectangle on the subdev's sink pad is scaled to the size configured
> > >   using the
> > >   :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
> > >   using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
> > >   subdev supports scaling but not composing, the top and left values are
> > >   not used and must always be set to zero.
> > 
> > Right, this sentence does imply that when scaling is supported, there
> > must be a sink compose rectangle, even when composing is not.
> > 
> > I have previously set up scaling like this:
> > 
> > media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> > media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
> > 
> > Does this mean, it should work like this instead?
> > 
> > media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> > media-ctl --set-v4l2 "'ipu1_csi0':0[fmt:UYVY2X8/1920x1080@1/60,compose:(0,0)/960x540]"
> > media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
> > 
> > I suppose setting the source pad format should not be allowed to modify
> > the sink compose rectangle.
> 
> That is what I believe having read these documents several times, but
> we need v4l2 people to confirm.
> 
> Note that setting the format on 'ipu1_csi0':0 should already be done by
> the previous media-ctl command, so it should be possible to simplify
> that to:
> 
> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> media-ctl --set-v4l2 "'ipu1_csi0':0[compose:(0,0)/960x540]"
> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"

There is a slightly puzzling bit in the documentation.  If we consider
the CSI, and the sink compose rectangle size has to always match the
the source output pad format size (since in hardware they are one of
the same), then:

  Inside subdevs, the order of image processing steps will always be from
  the sink pad towards the source pad. This is also reflected in the order
  in which the configuration must be performed by the user: the changes
  made will be propagated to any subsequent stages. If this behaviour is
  not desired, the user must set ``V4L2_SEL_FLAG_KEEP_CONFIG`` flag. This
                                                                     ^^^^
  flag causes no propagation of the changes are allowed in any
  ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
  circumstances. This may also cause the accessed rectangle to be adjusted
  ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
  by the driver, depending on the properties of the underlying hardware.
  ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

presumably, this means if we get a request to change the source compose
rectangle with V4L2_SEL_FLAG_KEEP_CONFIG set, we need to force its size
to be the current output format size.  I don't think we can do anything
else - because the above makes it very clear that any following stages
shall not be updated.  The last sentence appears to give permission to
do that.

This also has implications when changing the sink crop - the sink crop
(eg) must not be smaller than the sink compose, as we don't support
scaling up in CSI.

It seems to me that V4L2_SEL_FLAG_KEEP_CONFIG in practice changes the
way validation of the request works.  So, rather than validating the
request against the upstream rectangle and propagating downstream, it
needs to be validated against both the upstream and downstream
rectangles instead.

It seems there's many subtleties to this...

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 02:17:05PM +0000, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 03:00:51PM +0100, Philipp Zabel wrote:
> > On Mon, 2017-03-20 at 12:08 +0000, Russell King - ARM Linux wrote:
> > > The same document says:
> > > 
> > >   Scaling support is optional. When supported by a subdev, the crop
> > >   rectangle on the subdev's sink pad is scaled to the size configured
> > >   using the
> > >   :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
> > >   using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
> > >   subdev supports scaling but not composing, the top and left values are
> > >   not used and must always be set to zero.
> > 
> > Right, this sentence does imply that when scaling is supported, there
> > must be a sink compose rectangle, even when composing is not.
> > 
> > I have previously set up scaling like this:
> > 
> > media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080 at 1/60]"
> > media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540 at 1/30]"
> > 
> > Does this mean, it should work like this instead?
> > 
> > media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080 at 1/60]"
> > media-ctl --set-v4l2 "'ipu1_csi0':0[fmt:UYVY2X8/1920x1080 at 1/60,compose:(0,0)/960x540]"
> > media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540 at 1/30]"
> > 
> > I suppose setting the source pad format should not be allowed to modify
> > the sink compose rectangle.
> 
> That is what I believe having read these documents several times, but
> we need v4l2 people to confirm.
> 
> Note that setting the format on 'ipu1_csi0':0 should already be done by
> the previous media-ctl command, so it should be possible to simplify
> that to:
> 
> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080 at 1/60]"
> media-ctl --set-v4l2 "'ipu1_csi0':0[compose:(0,0)/960x540]"
> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540 at 1/30]"

There is a slightly puzzling bit in the documentation.  If we consider
the CSI, and the sink compose rectangle size has to always match the
the source output pad format size (since in hardware they are one of
the same), then:

  Inside subdevs, the order of image processing steps will always be from
  the sink pad towards the source pad. This is also reflected in the order
  in which the configuration must be performed by the user: the changes
  made will be propagated to any subsequent stages. If this behaviour is
  not desired, the user must set ``V4L2_SEL_FLAG_KEEP_CONFIG`` flag. This
                                                                     ^^^^
  flag causes no propagation of the changes are allowed in any
  ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
  circumstances. This may also cause the accessed rectangle to be adjusted
  ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
  by the driver, depending on the properties of the underlying hardware.
  ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

presumably, this means if we get a request to change the source compose
rectangle with V4L2_SEL_FLAG_KEEP_CONFIG set, we need to force its size
to be the current output format size.  I don't think we can do anything
else - because the above makes it very clear that any following stages
shall not be updated.  The last sentence appears to give permission to
do that.

This also has implications when changing the sink crop - the sink crop
(eg) must not be smaller than the sink compose, as we don't support
scaling up in CSI.

It seems to me that V4L2_SEL_FLAG_KEEP_CONFIG in practice changes the
way validation of the request works.  So, rather than validating the
request against the upstream rectangle and propagating downstream, it
needs to be validated against both the upstream and downstream
rectangles instead.

It seems there's many subtleties to this...

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 02:17:05PM +0000, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 03:00:51PM +0100, Philipp Zabel wrote:
> > On Mon, 2017-03-20 at 12:08 +0000, Russell King - ARM Linux wrote:
> > > The same document says:
> > > 
> > >   Scaling support is optional. When supported by a subdev, the crop
> > >   rectangle on the subdev's sink pad is scaled to the size configured
> > >   using the
> > >   :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
> > >   using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
> > >   subdev supports scaling but not composing, the top and left values are
> > >   not used and must always be set to zero.
> > 
> > Right, this sentence does imply that when scaling is supported, there
> > must be a sink compose rectangle, even when composing is not.
> > 
> > I have previously set up scaling like this:
> > 
> > media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> > media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
> > 
> > Does this mean, it should work like this instead?
> > 
> > media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> > media-ctl --set-v4l2 "'ipu1_csi0':0[fmt:UYVY2X8/1920x1080@1/60,compose:(0,0)/960x540]"
> > media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
> > 
> > I suppose setting the source pad format should not be allowed to modify
> > the sink compose rectangle.
> 
> That is what I believe having read these documents several times, but
> we need v4l2 people to confirm.
> 
> Note that setting the format on 'ipu1_csi0':0 should already be done by
> the previous media-ctl command, so it should be possible to simplify
> that to:
> 
> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> media-ctl --set-v4l2 "'ipu1_csi0':0[compose:(0,0)/960x540]"
> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"

There is a slightly puzzling bit in the documentation.  If we consider
the CSI, and the sink compose rectangle size has to always match the
the source output pad format size (since in hardware they are one of
the same), then:

  Inside subdevs, the order of image processing steps will always be from
  the sink pad towards the source pad. This is also reflected in the order
  in which the configuration must be performed by the user: the changes
  made will be propagated to any subsequent stages. If this behaviour is
  not desired, the user must set ``V4L2_SEL_FLAG_KEEP_CONFIG`` flag. This
                                                                     ^^^^
  flag causes no propagation of the changes are allowed in any
  ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
  circumstances. This may also cause the accessed rectangle to be adjusted
  ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
  by the driver, depending on the properties of the underlying hardware.
  ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

presumably, this means if we get a request to change the source compose
rectangle with V4L2_SEL_FLAG_KEEP_CONFIG set, we need to force its size
to be the current output format size.  I don't think we can do anything
else - because the above makes it very clear that any following stages
shall not be updated.  The last sentence appears to give permission to
do that.

This also has implications when changing the sink crop - the sink crop
(eg) must not be smaller than the sink compose, as we don't support
scaling up in CSI.

It seems to me that V4L2_SEL_FLAG_KEEP_CONFIG in practice changes the
way validation of the request works.  So, rather than validating the
request against the upstream rectangle and propagating downstream, it
needs to be validated against both the upstream and downstream
rectangles instead.

It seems there's many subtleties to this...

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Philipp Zabel]

Hi Steve, Russell,

On Mon, 2017-03-20 at 14:17 +0000, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 03:00:51PM +0100, Philipp Zabel wrote:
> > On Mon, 2017-03-20 at 12:08 +0000, Russell King - ARM Linux wrote:
> > > The same document says:
> > > 
> > >   Scaling support is optional. When supported by a subdev, the crop
> > >   rectangle on the subdev's sink pad is scaled to the size configured
> > >   using the
> > >   :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
> > >   using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
> > >   subdev supports scaling but not composing, the top and left values are
> > >   not used and must always be set to zero.
> > 
> > Right, this sentence does imply that when scaling is supported, there
> > must be a sink compose rectangle, even when composing is not.
> > 
> > I have previously set up scaling like this:
> > 
> > media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> > media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
> > 
> > Does this mean, it should work like this instead?
> > 
> > media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> > media-ctl --set-v4l2 "'ipu1_csi0':0[fmt:UYVY2X8/1920x1080@1/60,compose:(0,0)/960x540]"
> > media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
> > 
> > I suppose setting the source pad format should not be allowed to modify
> > the sink compose rectangle.
> 
> That is what I believe having read these documents several times, but
> we need v4l2 people to confirm.

What do you think of this:

----------8<----------
>From 2830aebc404bdfc9d7fc1ec94e5282d0b668e8f6 Mon Sep 17 00:00:00 2001
From: Philipp Zabel <p.zabel@pengutronix.de>
Date: Mon, 20 Mar 2017 17:10:21 +0100
Subject: [PATCH] media: imx: csi: add sink selection rectangles

Move the crop rectangle to the sink pad and add a sink compose rectangle
to configure scaling. Also propagate rectangles from sink pad to crop
rectangle, to compose rectangle, and to the source pads both in ACTIVE
and TRY variants of set_fmt/selection, and initialize the default crop
and compose rectangles.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
---
 drivers/staging/media/imx/imx-media-csi.c | 216 +++++++++++++++++++++---------
 1 file changed, 152 insertions(+), 64 deletions(-)

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index 560da3abdd70b..b026a5d602ddf 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -79,6 +79,7 @@ struct csi_priv {
 	const struct imx_media_pixfmt *cc[CSI_NUM_PADS];
 	struct v4l2_fract frame_interval;
 	struct v4l2_rect crop;
+	struct v4l2_rect compose;
 	const struct csi_skip_desc *skip[CSI_NUM_PADS - 1];
 
 	/* active vb2 buffers to send to video dev sink */
@@ -574,8 +575,8 @@ static int csi_setup(struct csi_priv *priv)
 	ipu_csi_set_window(priv->csi, &priv->crop);
 
 	ipu_csi_set_downsize(priv->csi,
-			     priv->crop.width == 2 * outfmt->width,
-			     priv->crop.height == 2 * outfmt->height);
+			     priv->crop.width == 2 * priv->compose.width,
+			     priv->crop.height == 2 * priv->compose.height);
 
 	ipu_csi_init_interface(priv->csi, &sensor_mbus_cfg, &if_fmt);
 
@@ -1001,6 +1002,27 @@ __csi_get_fmt(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
 		return &priv->format_mbus[pad];
 }
 
+static struct v4l2_rect *
+__csi_get_crop(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
+	       enum v4l2_subdev_format_whence which)
+{
+	if (which == V4L2_SUBDEV_FORMAT_TRY)
+		return v4l2_subdev_get_try_crop(&priv->sd, cfg, CSI_SINK_PAD);
+	else
+		return &priv->crop;
+}
+
+static struct v4l2_rect *
+__csi_get_compose(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
+		  enum v4l2_subdev_format_whence which)
+{
+	if (which == V4L2_SUBDEV_FORMAT_TRY)
+		return v4l2_subdev_get_try_compose(&priv->sd, cfg,
+						   CSI_SINK_PAD);
+	else
+		return &priv->compose;
+}
+
 static void csi_try_crop(struct csi_priv *priv,
 			 struct v4l2_rect *crop,
 			 struct v4l2_subdev_pad_config *cfg,
@@ -1159,6 +1181,7 @@ static void csi_try_fmt(struct csi_priv *priv,
 			struct v4l2_subdev_pad_config *cfg,
 			struct v4l2_subdev_format *sdformat,
 			struct v4l2_rect *crop,
+			struct v4l2_rect *compose,
 			const struct imx_media_pixfmt **cc)
 {
 	const struct imx_media_pixfmt *incc;
@@ -1173,15 +1196,8 @@ static void csi_try_fmt(struct csi_priv *priv,
 		incc = imx_media_find_mbus_format(infmt->code,
 						  CS_SEL_ANY, true);
 
-		if (sdformat->format.width < priv->crop.width * 3 / 4)
-			sdformat->format.width = priv->crop.width / 2;
-		else
-			sdformat->format.width = priv->crop.width;
-
-		if (sdformat->format.height < priv->crop.height * 3 / 4)
-			sdformat->format.height = priv->crop.height / 2;
-		else
-			sdformat->format.height = priv->crop.height;
+		sdformat->format.width = compose->width;
+		sdformat->format.height = compose->height;
 
 		if (incc->bayer) {
 			sdformat->format.code = infmt->code;
@@ -1217,11 +1233,17 @@ static void csi_try_fmt(struct csi_priv *priv,
 		v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
 				      W_ALIGN, &sdformat->format.height,
 				      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
+
+		/* Reset crop and compose rectangles */
 		crop->left = 0;
 		crop->top = 0;
 		crop->width = sdformat->format.width;
 		crop->height = sdformat->format.height;
 		csi_try_crop(priv, crop, cfg, &sdformat->format, sensor);
+		compose->left = 0;
+		compose->top = 0;
+		compose->width = crop->width;
+		compose->height = crop->height;
 
 		*cc = imx_media_find_mbus_format(sdformat->format.code,
 						 CS_SEL_ANY, true);
@@ -1245,7 +1267,8 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 	const struct imx_media_pixfmt *cc;
 	struct imx_media_subdev *sensor;
 	struct v4l2_pix_format vdev_fmt;
-	struct v4l2_rect crop;
+	struct v4l2_mbus_framefmt *fmt;
+	struct v4l2_rect *crop, *compose;
 	int ret = 0;
 
 	if (sdformat->pad >= CSI_NUM_PADS)
@@ -1264,37 +1287,42 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 		goto out;
 	}
 
-	csi_try_fmt(priv, sensor, cfg, sdformat, &crop, &cc);
+	crop = __csi_get_crop(priv, cfg, sdformat->which);
+	compose = __csi_get_compose(priv, cfg, sdformat->which);
 
-	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
-		cfg->try_fmt = sdformat->format;
-		goto out;
-	}
+	csi_try_fmt(priv, sensor, cfg, sdformat, crop, compose, &cc);
 
-	priv->format_mbus[sdformat->pad] = sdformat->format;
-	priv->cc[sdformat->pad] = cc;
+	fmt = __csi_get_fmt(priv, cfg, sdformat->pad, sdformat->which);
+	*fmt = sdformat->format;
 
 	if (sdformat->pad == CSI_SINK_PAD) {
 		int pad;
 
-		/* reset the crop window */
-		priv->crop = crop;
-
 		/* propagate format to source pads */
 		for (pad = CSI_SINK_PAD + 1; pad < CSI_NUM_PADS; pad++) {
 			const struct imx_media_pixfmt *outcc;
 			struct v4l2_subdev_format format;
+			struct v4l2_mbus_framefmt *outfmt;
 
 			format.pad = pad;
-			format.which = V4L2_SUBDEV_FORMAT_ACTIVE;
+			format.which = sdformat->which;
 			format.format = sdformat->format;
-			csi_try_fmt(priv, sensor, cfg, &format, &crop, &outcc);
+			csi_try_fmt(priv, sensor, cfg, &format, NULL, compose,
+				    &outcc);
 
-			priv->format_mbus[pad] = format.format;
-			priv->cc[pad] = outcc;
+			outfmt = __csi_get_fmt(priv, cfg, pad, sdformat->which);
+			*outfmt = format.format;
+
+			if (sdformat->which == V4L2_SUBDEV_FORMAT_ACTIVE)
+				priv->cc[pad] = outcc;
 		}
 	}
 
+	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY)
+		goto out;
+
+	priv->cc[sdformat->pad] = cc;
+
 	/* propagate IDMAC output pad format to capture device */
 	imx_media_mbus_fmt_to_pix_fmt(&vdev_fmt,
 				      &priv->format_mbus[CSI_SRC_PAD_IDMAC],
@@ -1314,18 +1342,17 @@ static int csi_get_selection(struct v4l2_subdev *sd,
 {
 	struct csi_priv *priv = v4l2_get_subdevdata(sd);
 	struct v4l2_mbus_framefmt *infmt;
+	struct v4l2_rect *crop, *compose;
 	int ret = 0;
 
-	if (sel->pad >= CSI_NUM_PADS || sel->pad == CSI_SINK_PAD)
+	if (sel->pad != CSI_SINK_PAD)
 		return -EINVAL;
 
 	mutex_lock(&priv->lock);
 
 	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
-	if (!infmt) {
-		ret = -EINVAL;
-		goto out;
-	}
+	crop = __csi_get_crop(priv, cfg, sel->which);
+	compose = __csi_get_compose(priv, cfg, sel->which);
 
 	switch (sel->target) {
 	case V4L2_SEL_TGT_CROP_BOUNDS:
@@ -1335,36 +1362,54 @@ static int csi_get_selection(struct v4l2_subdev *sd,
 		sel->r.height = infmt->height;
 		break;
 	case V4L2_SEL_TGT_CROP:
-		if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
-			struct v4l2_rect *try_crop =
-				v4l2_subdev_get_try_crop(&priv->sd,
-							 cfg, sel->pad);
-			sel->r = *try_crop;
-		} else {
-			sel->r = priv->crop;
-		}
+		sel->r = *crop;
+		break;
+	case V4L2_SEL_TGT_COMPOSE_BOUNDS:
+		sel->r.left = 0;
+		sel->r.top = 0;
+		sel->r.width = crop->width;
+		sel->r.height = crop->height;
+		break;
+	case V4L2_SEL_TGT_COMPOSE:
+		sel->r = *compose;
 		break;
 	default:
 		ret = -EINVAL;
 	}
 
-out:
 	mutex_unlock(&priv->lock);
 	return ret;
 }
 
+static int csi_set_scale(u32 *compose, u32 crop, u32 flags)
+{
+	if ((flags & (V4L2_SEL_FLAG_LE | V4L2_SEL_FLAG_GE)) ==
+		     (V4L2_SEL_FLAG_LE | V4L2_SEL_FLAG_GE) &&
+	    *compose != crop && *compose != crop / 2)
+		return -ERANGE;
+
+	if (*compose <= crop / 2 ||
+	    (*compose < crop * 3 / 4 && !(flags & V4L2_SEL_FLAG_GE)) ||
+	    (*compose < crop && (flags & V4L2_SEL_FLAG_LE)))
+		*compose = crop / 2;
+	else
+		*compose = crop;
+
+	return 0;
+}
+
 static int csi_set_selection(struct v4l2_subdev *sd,
 			     struct v4l2_subdev_pad_config *cfg,
 			     struct v4l2_subdev_selection *sel)
 {
 	struct csi_priv *priv = v4l2_get_subdevdata(sd);
 	struct v4l2_mbus_framefmt *infmt;
+	struct v4l2_rect *crop, *compose;
 	struct imx_media_subdev *sensor;
+	int pad;
 	int ret = 0;
 
-	if (sel->pad >= CSI_NUM_PADS ||
-	    sel->pad == CSI_SINK_PAD ||
-	    sel->target != V4L2_SEL_TGT_CROP)
+	if (sel->pad != CSI_SINK_PAD)
 		return -EINVAL;
 
 	sensor = imx_media_find_sensor(priv->md, &priv->sd.entity);
@@ -1380,31 +1425,68 @@ static int csi_set_selection(struct v4l2_subdev *sd,
 		goto out;
 	}
 
-	/*
-	 * Modifying the crop rectangle always changes the format on the source
-	 * pad. If the KEEP_CONFIG flag is set, just return the current crop
-	 * rectangle.
-	 */
-	if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
-		sel->r = priv->crop;
-		if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
-			cfg->try_crop = sel->r;
+	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
+	crop = __csi_get_crop(priv, cfg, sel->which);
+	compose = __csi_get_compose(priv, cfg, sel->which);
+
+	switch (sel->target) {
+	case V4L2_SEL_TGT_CROP:
+		/*
+		 * Modifying the crop rectangle always changes the format on
+		 * the source pads. If the KEEP_CONFIG flag is set, just return
+		 * the current crop rectangle.
+		 */
+		if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
+			sel->r = priv->crop;
+			if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
+				*crop = sel->r;
+			goto out;
+		}
+
+		csi_try_crop(priv, &sel->r, cfg, infmt, sensor);
+
+		*crop = sel->r;
+
+		/* Reset scaling to 1:1 */
+		compose->width = crop->width;
+		compose->height = crop->height;
+		break;
+	case V4L2_SEL_TGT_COMPOSE:
+		/*
+		 * Modifying the compose rectangle always changes the format on
+		 * the source pads. If the KEEP_CONFIG flag is set, just return
+		 * the current compose rectangle.
+		 */
+		if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
+			sel->r = priv->compose;
+			if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
+				*compose = sel->r;
+			goto out;
+		}
+
+		sel->r.left = 0;
+		sel->r.top = 0;
+		ret = csi_set_scale(&sel->r.width, crop->width, sel->flags);
+		if (ret)
+			goto out;
+		ret = csi_set_scale(&sel->r.height, crop->height, sel->flags);
+		if (ret)
+			goto out;
+
+		*compose = sel->r;
+		break;
+	default:
+		ret = -EINVAL;
 		goto out;
 	}
 
-	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
-	csi_try_crop(priv, &sel->r, cfg, infmt, sensor);
-
-	if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
-		cfg->try_crop = sel->r;
-	} else {
-		struct v4l2_mbus_framefmt *outfmt =
-			&priv->format_mbus[sel->pad];
+	/* Reset source pads to sink compose rectangle */
+	for (pad = CSI_SINK_PAD + 1; pad < CSI_NUM_PADS; pad++) {
+		struct v4l2_mbus_framefmt *outfmt;
 
-		priv->crop = sel->r;
-		/* Update the source format */
-		outfmt->width = sel->r.width;
-		outfmt->height = sel->r.height;
+		outfmt = __csi_get_fmt(priv, cfg, pad, sel->which);
+		outfmt->width = compose->width;
+		outfmt->height = compose->height;
 	}
 
 out:
@@ -1467,6 +1549,12 @@ static int csi_registered(struct v4l2_subdev *sd)
 			priv->skip[i - 1] = &csi_skip[0];
 	}
 
+	/* init default crop and compose rectangle sizes */
+	priv->crop.width = 640;
+	priv->crop.height = 480;
+	priv->compose.width = 640;
+	priv->compose.height = 480;
+
 	/* init default frame interval */
 	priv->frame_interval.numerator = 1;
 	priv->frame_interval.denominator = 30;
-- 
2.11.0
---------->8----------

regards
Philipp

[PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Philipp Zabel]

Hi Steve, Russell,

On Mon, 2017-03-20 at 14:17 +0000, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 03:00:51PM +0100, Philipp Zabel wrote:
> > On Mon, 2017-03-20 at 12:08 +0000, Russell King - ARM Linux wrote:
> > > The same document says:
> > > 
> > >   Scaling support is optional. When supported by a subdev, the crop
> > >   rectangle on the subdev's sink pad is scaled to the size configured
> > >   using the
> > >   :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
> > >   using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
> > >   subdev supports scaling but not composing, the top and left values are
> > >   not used and must always be set to zero.
> > 
> > Right, this sentence does imply that when scaling is supported, there
> > must be a sink compose rectangle, even when composing is not.
> > 
> > I have previously set up scaling like this:
> > 
> > media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080 at 1/60]"
> > media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540 at 1/30]"
> > 
> > Does this mean, it should work like this instead?
> > 
> > media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080 at 1/60]"
> > media-ctl --set-v4l2 "'ipu1_csi0':0[fmt:UYVY2X8/1920x1080 at 1/60,compose:(0,0)/960x540]"
> > media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540 at 1/30]"
> > 
> > I suppose setting the source pad format should not be allowed to modify
> > the sink compose rectangle.
> 
> That is what I believe having read these documents several times, but
> we need v4l2 people to confirm.

What do you think of this:

----------8<----------
>From 2830aebc404bdfc9d7fc1ec94e5282d0b668e8f6 Mon Sep 17 00:00:00 2001
From: Philipp Zabel <p.zabel@pengutronix.de>
Date: Mon, 20 Mar 2017 17:10:21 +0100
Subject: [PATCH] media: imx: csi: add sink selection rectangles

Move the crop rectangle to the sink pad and add a sink compose rectangle
to configure scaling. Also propagate rectangles from sink pad to crop
rectangle, to compose rectangle, and to the source pads both in ACTIVE
and TRY variants of set_fmt/selection, and initialize the default crop
and compose rectangles.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
---
 drivers/staging/media/imx/imx-media-csi.c | 216 +++++++++++++++++++++---------
 1 file changed, 152 insertions(+), 64 deletions(-)

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index 560da3abdd70b..b026a5d602ddf 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -79,6 +79,7 @@ struct csi_priv {
 	const struct imx_media_pixfmt *cc[CSI_NUM_PADS];
 	struct v4l2_fract frame_interval;
 	struct v4l2_rect crop;
+	struct v4l2_rect compose;
 	const struct csi_skip_desc *skip[CSI_NUM_PADS - 1];
 
 	/* active vb2 buffers to send to video dev sink */
@@ -574,8 +575,8 @@ static int csi_setup(struct csi_priv *priv)
 	ipu_csi_set_window(priv->csi, &priv->crop);
 
 	ipu_csi_set_downsize(priv->csi,
-			     priv->crop.width == 2 * outfmt->width,
-			     priv->crop.height == 2 * outfmt->height);
+			     priv->crop.width == 2 * priv->compose.width,
+			     priv->crop.height == 2 * priv->compose.height);
 
 	ipu_csi_init_interface(priv->csi, &sensor_mbus_cfg, &if_fmt);
 
@@ -1001,6 +1002,27 @@ __csi_get_fmt(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
 		return &priv->format_mbus[pad];
 }
 
+static struct v4l2_rect *
+__csi_get_crop(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
+	       enum v4l2_subdev_format_whence which)
+{
+	if (which == V4L2_SUBDEV_FORMAT_TRY)
+		return v4l2_subdev_get_try_crop(&priv->sd, cfg, CSI_SINK_PAD);
+	else
+		return &priv->crop;
+}
+
+static struct v4l2_rect *
+__csi_get_compose(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
+		  enum v4l2_subdev_format_whence which)
+{
+	if (which == V4L2_SUBDEV_FORMAT_TRY)
+		return v4l2_subdev_get_try_compose(&priv->sd, cfg,
+						   CSI_SINK_PAD);
+	else
+		return &priv->compose;
+}
+
 static void csi_try_crop(struct csi_priv *priv,
 			 struct v4l2_rect *crop,
 			 struct v4l2_subdev_pad_config *cfg,
@@ -1159,6 +1181,7 @@ static void csi_try_fmt(struct csi_priv *priv,
 			struct v4l2_subdev_pad_config *cfg,
 			struct v4l2_subdev_format *sdformat,
 			struct v4l2_rect *crop,
+			struct v4l2_rect *compose,
 			const struct imx_media_pixfmt **cc)
 {
 	const struct imx_media_pixfmt *incc;
@@ -1173,15 +1196,8 @@ static void csi_try_fmt(struct csi_priv *priv,
 		incc = imx_media_find_mbus_format(infmt->code,
 						  CS_SEL_ANY, true);
 
-		if (sdformat->format.width < priv->crop.width * 3 / 4)
-			sdformat->format.width = priv->crop.width / 2;
-		else
-			sdformat->format.width = priv->crop.width;
-
-		if (sdformat->format.height < priv->crop.height * 3 / 4)
-			sdformat->format.height = priv->crop.height / 2;
-		else
-			sdformat->format.height = priv->crop.height;
+		sdformat->format.width = compose->width;
+		sdformat->format.height = compose->height;
 
 		if (incc->bayer) {
 			sdformat->format.code = infmt->code;
@@ -1217,11 +1233,17 @@ static void csi_try_fmt(struct csi_priv *priv,
 		v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
 				      W_ALIGN, &sdformat->format.height,
 				      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
+
+		/* Reset crop and compose rectangles */
 		crop->left = 0;
 		crop->top = 0;
 		crop->width = sdformat->format.width;
 		crop->height = sdformat->format.height;
 		csi_try_crop(priv, crop, cfg, &sdformat->format, sensor);
+		compose->left = 0;
+		compose->top = 0;
+		compose->width = crop->width;
+		compose->height = crop->height;
 
 		*cc = imx_media_find_mbus_format(sdformat->format.code,
 						 CS_SEL_ANY, true);
@@ -1245,7 +1267,8 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 	const struct imx_media_pixfmt *cc;
 	struct imx_media_subdev *sensor;
 	struct v4l2_pix_format vdev_fmt;
-	struct v4l2_rect crop;
+	struct v4l2_mbus_framefmt *fmt;
+	struct v4l2_rect *crop, *compose;
 	int ret = 0;
 
 	if (sdformat->pad >= CSI_NUM_PADS)
@@ -1264,37 +1287,42 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 		goto out;
 	}
 
-	csi_try_fmt(priv, sensor, cfg, sdformat, &crop, &cc);
+	crop = __csi_get_crop(priv, cfg, sdformat->which);
+	compose = __csi_get_compose(priv, cfg, sdformat->which);
 
-	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
-		cfg->try_fmt = sdformat->format;
-		goto out;
-	}
+	csi_try_fmt(priv, sensor, cfg, sdformat, crop, compose, &cc);
 
-	priv->format_mbus[sdformat->pad] = sdformat->format;
-	priv->cc[sdformat->pad] = cc;
+	fmt = __csi_get_fmt(priv, cfg, sdformat->pad, sdformat->which);
+	*fmt = sdformat->format;
 
 	if (sdformat->pad == CSI_SINK_PAD) {
 		int pad;
 
-		/* reset the crop window */
-		priv->crop = crop;
-
 		/* propagate format to source pads */
 		for (pad = CSI_SINK_PAD + 1; pad < CSI_NUM_PADS; pad++) {
 			const struct imx_media_pixfmt *outcc;
 			struct v4l2_subdev_format format;
+			struct v4l2_mbus_framefmt *outfmt;
 
 			format.pad = pad;
-			format.which = V4L2_SUBDEV_FORMAT_ACTIVE;
+			format.which = sdformat->which;
 			format.format = sdformat->format;
-			csi_try_fmt(priv, sensor, cfg, &format, &crop, &outcc);
+			csi_try_fmt(priv, sensor, cfg, &format, NULL, compose,
+				    &outcc);
 
-			priv->format_mbus[pad] = format.format;
-			priv->cc[pad] = outcc;
+			outfmt = __csi_get_fmt(priv, cfg, pad, sdformat->which);
+			*outfmt = format.format;
+
+			if (sdformat->which == V4L2_SUBDEV_FORMAT_ACTIVE)
+				priv->cc[pad] = outcc;
 		}
 	}
 
+	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY)
+		goto out;
+
+	priv->cc[sdformat->pad] = cc;
+
 	/* propagate IDMAC output pad format to capture device */
 	imx_media_mbus_fmt_to_pix_fmt(&vdev_fmt,
 				      &priv->format_mbus[CSI_SRC_PAD_IDMAC],
@@ -1314,18 +1342,17 @@ static int csi_get_selection(struct v4l2_subdev *sd,
 {
 	struct csi_priv *priv = v4l2_get_subdevdata(sd);
 	struct v4l2_mbus_framefmt *infmt;
+	struct v4l2_rect *crop, *compose;
 	int ret = 0;
 
-	if (sel->pad >= CSI_NUM_PADS || sel->pad == CSI_SINK_PAD)
+	if (sel->pad != CSI_SINK_PAD)
 		return -EINVAL;
 
 	mutex_lock(&priv->lock);
 
 	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
-	if (!infmt) {
-		ret = -EINVAL;
-		goto out;
-	}
+	crop = __csi_get_crop(priv, cfg, sel->which);
+	compose = __csi_get_compose(priv, cfg, sel->which);
 
 	switch (sel->target) {
 	case V4L2_SEL_TGT_CROP_BOUNDS:
@@ -1335,36 +1362,54 @@ static int csi_get_selection(struct v4l2_subdev *sd,
 		sel->r.height = infmt->height;
 		break;
 	case V4L2_SEL_TGT_CROP:
-		if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
-			struct v4l2_rect *try_crop =
-				v4l2_subdev_get_try_crop(&priv->sd,
-							 cfg, sel->pad);
-			sel->r = *try_crop;
-		} else {
-			sel->r = priv->crop;
-		}
+		sel->r = *crop;
+		break;
+	case V4L2_SEL_TGT_COMPOSE_BOUNDS:
+		sel->r.left = 0;
+		sel->r.top = 0;
+		sel->r.width = crop->width;
+		sel->r.height = crop->height;
+		break;
+	case V4L2_SEL_TGT_COMPOSE:
+		sel->r = *compose;
 		break;
 	default:
 		ret = -EINVAL;
 	}
 
-out:
 	mutex_unlock(&priv->lock);
 	return ret;
 }
 
+static int csi_set_scale(u32 *compose, u32 crop, u32 flags)
+{
+	if ((flags & (V4L2_SEL_FLAG_LE | V4L2_SEL_FLAG_GE)) ==
+		     (V4L2_SEL_FLAG_LE | V4L2_SEL_FLAG_GE) &&
+	    *compose != crop && *compose != crop / 2)
+		return -ERANGE;
+
+	if (*compose <= crop / 2 ||
+	    (*compose < crop * 3 / 4 && !(flags & V4L2_SEL_FLAG_GE)) ||
+	    (*compose < crop && (flags & V4L2_SEL_FLAG_LE)))
+		*compose = crop / 2;
+	else
+		*compose = crop;
+
+	return 0;
+}
+
 static int csi_set_selection(struct v4l2_subdev *sd,
 			     struct v4l2_subdev_pad_config *cfg,
 			     struct v4l2_subdev_selection *sel)
 {
 	struct csi_priv *priv = v4l2_get_subdevdata(sd);
 	struct v4l2_mbus_framefmt *infmt;
+	struct v4l2_rect *crop, *compose;
 	struct imx_media_subdev *sensor;
+	int pad;
 	int ret = 0;
 
-	if (sel->pad >= CSI_NUM_PADS ||
-	    sel->pad == CSI_SINK_PAD ||
-	    sel->target != V4L2_SEL_TGT_CROP)
+	if (sel->pad != CSI_SINK_PAD)
 		return -EINVAL;
 
 	sensor = imx_media_find_sensor(priv->md, &priv->sd.entity);
@@ -1380,31 +1425,68 @@ static int csi_set_selection(struct v4l2_subdev *sd,
 		goto out;
 	}
 
-	/*
-	 * Modifying the crop rectangle always changes the format on the source
-	 * pad. If the KEEP_CONFIG flag is set, just return the current crop
-	 * rectangle.
-	 */
-	if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
-		sel->r = priv->crop;
-		if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
-			cfg->try_crop = sel->r;
+	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
+	crop = __csi_get_crop(priv, cfg, sel->which);
+	compose = __csi_get_compose(priv, cfg, sel->which);
+
+	switch (sel->target) {
+	case V4L2_SEL_TGT_CROP:
+		/*
+		 * Modifying the crop rectangle always changes the format on
+		 * the source pads. If the KEEP_CONFIG flag is set, just return
+		 * the current crop rectangle.
+		 */
+		if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
+			sel->r = priv->crop;
+			if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
+				*crop = sel->r;
+			goto out;
+		}
+
+		csi_try_crop(priv, &sel->r, cfg, infmt, sensor);
+
+		*crop = sel->r;
+
+		/* Reset scaling to 1:1 */
+		compose->width = crop->width;
+		compose->height = crop->height;
+		break;
+	case V4L2_SEL_TGT_COMPOSE:
+		/*
+		 * Modifying the compose rectangle always changes the format on
+		 * the source pads. If the KEEP_CONFIG flag is set, just return
+		 * the current compose rectangle.
+		 */
+		if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
+			sel->r = priv->compose;
+			if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
+				*compose = sel->r;
+			goto out;
+		}
+
+		sel->r.left = 0;
+		sel->r.top = 0;
+		ret = csi_set_scale(&sel->r.width, crop->width, sel->flags);
+		if (ret)
+			goto out;
+		ret = csi_set_scale(&sel->r.height, crop->height, sel->flags);
+		if (ret)
+			goto out;
+
+		*compose = sel->r;
+		break;
+	default:
+		ret = -EINVAL;
 		goto out;
 	}
 
-	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
-	csi_try_crop(priv, &sel->r, cfg, infmt, sensor);
-
-	if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
-		cfg->try_crop = sel->r;
-	} else {
-		struct v4l2_mbus_framefmt *outfmt =
-			&priv->format_mbus[sel->pad];
+	/* Reset source pads to sink compose rectangle */
+	for (pad = CSI_SINK_PAD + 1; pad < CSI_NUM_PADS; pad++) {
+		struct v4l2_mbus_framefmt *outfmt;
 
-		priv->crop = sel->r;
-		/* Update the source format */
-		outfmt->width = sel->r.width;
-		outfmt->height = sel->r.height;
+		outfmt = __csi_get_fmt(priv, cfg, pad, sel->which);
+		outfmt->width = compose->width;
+		outfmt->height = compose->height;
 	}
 
 out:
@@ -1467,6 +1549,12 @@ static int csi_registered(struct v4l2_subdev *sd)
 			priv->skip[i - 1] = &csi_skip[0];
 	}
 
+	/* init default crop and compose rectangle sizes */
+	priv->crop.width = 640;
+	priv->crop.height = 480;
+	priv->compose.width = 640;
+	priv->compose.height = 480;
+
 	/* init default frame interval */
 	priv->frame_interval.numerator = 1;
 	priv->frame_interval.denominator = 30;
-- 
2.11.0
---------->8----------

regards
Philipp

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Philipp Zabel]

Hi Steve, Russell,

On Mon, 2017-03-20 at 14:17 +0000, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 03:00:51PM +0100, Philipp Zabel wrote:
> > On Mon, 2017-03-20 at 12:08 +0000, Russell King - ARM Linux wrote:
> > > The same document says:
> > > 
> > >   Scaling support is optional. When supported by a subdev, the crop
> > >   rectangle on the subdev's sink pad is scaled to the size configured
> > >   using the
> > >   :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
> > >   using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
> > >   subdev supports scaling but not composing, the top and left values are
> > >   not used and must always be set to zero.
> > 
> > Right, this sentence does imply that when scaling is supported, there
> > must be a sink compose rectangle, even when composing is not.
> > 
> > I have previously set up scaling like this:
> > 
> > media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> > media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
> > 
> > Does this mean, it should work like this instead?
> > 
> > media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> > media-ctl --set-v4l2 "'ipu1_csi0':0[fmt:UYVY2X8/1920x1080@1/60,compose:(0,0)/960x540]"
> > media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
> > 
> > I suppose setting the source pad format should not be allowed to modify
> > the sink compose rectangle.
> 
> That is what I believe having read these documents several times, but
> we need v4l2 people to confirm.

What do you think of this:

----------8<----------
>From 2830aebc404bdfc9d7fc1ec94e5282d0b668e8f6 Mon Sep 17 00:00:00 2001
From: Philipp Zabel <p.zabel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
Date: Mon, 20 Mar 2017 17:10:21 +0100
Subject: [PATCH] media: imx: csi: add sink selection rectangles

Move the crop rectangle to the sink pad and add a sink compose rectangle
to configure scaling. Also propagate rectangles from sink pad to crop
rectangle, to compose rectangle, and to the source pads both in ACTIVE
and TRY variants of set_fmt/selection, and initialize the default crop
and compose rectangles.

Signed-off-by: Philipp Zabel <p.zabel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
---
 drivers/staging/media/imx/imx-media-csi.c | 216 +++++++++++++++++++++---------
 1 file changed, 152 insertions(+), 64 deletions(-)

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index 560da3abdd70b..b026a5d602ddf 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -79,6 +79,7 @@ struct csi_priv {
 	const struct imx_media_pixfmt *cc[CSI_NUM_PADS];
 	struct v4l2_fract frame_interval;
 	struct v4l2_rect crop;
+	struct v4l2_rect compose;
 	const struct csi_skip_desc *skip[CSI_NUM_PADS - 1];
 
 	/* active vb2 buffers to send to video dev sink */
@@ -574,8 +575,8 @@ static int csi_setup(struct csi_priv *priv)
 	ipu_csi_set_window(priv->csi, &priv->crop);
 
 	ipu_csi_set_downsize(priv->csi,
-			     priv->crop.width == 2 * outfmt->width,
-			     priv->crop.height == 2 * outfmt->height);
+			     priv->crop.width == 2 * priv->compose.width,
+			     priv->crop.height == 2 * priv->compose.height);
 
 	ipu_csi_init_interface(priv->csi, &sensor_mbus_cfg, &if_fmt);
 
@@ -1001,6 +1002,27 @@ __csi_get_fmt(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
 		return &priv->format_mbus[pad];
 }
 
+static struct v4l2_rect *
+__csi_get_crop(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
+	       enum v4l2_subdev_format_whence which)
+{
+	if (which == V4L2_SUBDEV_FORMAT_TRY)
+		return v4l2_subdev_get_try_crop(&priv->sd, cfg, CSI_SINK_PAD);
+	else
+		return &priv->crop;
+}
+
+static struct v4l2_rect *
+__csi_get_compose(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
+		  enum v4l2_subdev_format_whence which)
+{
+	if (which == V4L2_SUBDEV_FORMAT_TRY)
+		return v4l2_subdev_get_try_compose(&priv->sd, cfg,
+						   CSI_SINK_PAD);
+	else
+		return &priv->compose;
+}
+
 static void csi_try_crop(struct csi_priv *priv,
 			 struct v4l2_rect *crop,
 			 struct v4l2_subdev_pad_config *cfg,
@@ -1159,6 +1181,7 @@ static void csi_try_fmt(struct csi_priv *priv,
 			struct v4l2_subdev_pad_config *cfg,
 			struct v4l2_subdev_format *sdformat,
 			struct v4l2_rect *crop,
+			struct v4l2_rect *compose,
 			const struct imx_media_pixfmt **cc)
 {
 	const struct imx_media_pixfmt *incc;
@@ -1173,15 +1196,8 @@ static void csi_try_fmt(struct csi_priv *priv,
 		incc = imx_media_find_mbus_format(infmt->code,
 						  CS_SEL_ANY, true);
 
-		if (sdformat->format.width < priv->crop.width * 3 / 4)
-			sdformat->format.width = priv->crop.width / 2;
-		else
-			sdformat->format.width = priv->crop.width;
-
-		if (sdformat->format.height < priv->crop.height * 3 / 4)
-			sdformat->format.height = priv->crop.height / 2;
-		else
-			sdformat->format.height = priv->crop.height;
+		sdformat->format.width = compose->width;
+		sdformat->format.height = compose->height;
 
 		if (incc->bayer) {
 			sdformat->format.code = infmt->code;
@@ -1217,11 +1233,17 @@ static void csi_try_fmt(struct csi_priv *priv,
 		v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
 				      W_ALIGN, &sdformat->format.height,
 				      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
+
+		/* Reset crop and compose rectangles */
 		crop->left = 0;
 		crop->top = 0;
 		crop->width = sdformat->format.width;
 		crop->height = sdformat->format.height;
 		csi_try_crop(priv, crop, cfg, &sdformat->format, sensor);
+		compose->left = 0;
+		compose->top = 0;
+		compose->width = crop->width;
+		compose->height = crop->height;
 
 		*cc = imx_media_find_mbus_format(sdformat->format.code,
 						 CS_SEL_ANY, true);
@@ -1245,7 +1267,8 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 	const struct imx_media_pixfmt *cc;
 	struct imx_media_subdev *sensor;
 	struct v4l2_pix_format vdev_fmt;
-	struct v4l2_rect crop;
+	struct v4l2_mbus_framefmt *fmt;
+	struct v4l2_rect *crop, *compose;
 	int ret = 0;
 
 	if (sdformat->pad >= CSI_NUM_PADS)
@@ -1264,37 +1287,42 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 		goto out;
 	}
 
-	csi_try_fmt(priv, sensor, cfg, sdformat, &crop, &cc);
+	crop = __csi_get_crop(priv, cfg, sdformat->which);
+	compose = __csi_get_compose(priv, cfg, sdformat->which);
 
-	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
-		cfg->try_fmt = sdformat->format;
-		goto out;
-	}
+	csi_try_fmt(priv, sensor, cfg, sdformat, crop, compose, &cc);
 
-	priv->format_mbus[sdformat->pad] = sdformat->format;
-	priv->cc[sdformat->pad] = cc;
+	fmt = __csi_get_fmt(priv, cfg, sdformat->pad, sdformat->which);
+	*fmt = sdformat->format;
 
 	if (sdformat->pad == CSI_SINK_PAD) {
 		int pad;
 
-		/* reset the crop window */
-		priv->crop = crop;
-
 		/* propagate format to source pads */
 		for (pad = CSI_SINK_PAD + 1; pad < CSI_NUM_PADS; pad++) {
 			const struct imx_media_pixfmt *outcc;
 			struct v4l2_subdev_format format;
+			struct v4l2_mbus_framefmt *outfmt;
 
 			format.pad = pad;
-			format.which = V4L2_SUBDEV_FORMAT_ACTIVE;
+			format.which = sdformat->which;
 			format.format = sdformat->format;
-			csi_try_fmt(priv, sensor, cfg, &format, &crop, &outcc);
+			csi_try_fmt(priv, sensor, cfg, &format, NULL, compose,
+				    &outcc);
 
-			priv->format_mbus[pad] = format.format;
-			priv->cc[pad] = outcc;
+			outfmt = __csi_get_fmt(priv, cfg, pad, sdformat->which);
+			*outfmt = format.format;
+
+			if (sdformat->which == V4L2_SUBDEV_FORMAT_ACTIVE)
+				priv->cc[pad] = outcc;
 		}
 	}
 
+	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY)
+		goto out;
+
+	priv->cc[sdformat->pad] = cc;
+
 	/* propagate IDMAC output pad format to capture device */
 	imx_media_mbus_fmt_to_pix_fmt(&vdev_fmt,
 				      &priv->format_mbus[CSI_SRC_PAD_IDMAC],
@@ -1314,18 +1342,17 @@ static int csi_get_selection(struct v4l2_subdev *sd,
 {
 	struct csi_priv *priv = v4l2_get_subdevdata(sd);
 	struct v4l2_mbus_framefmt *infmt;
+	struct v4l2_rect *crop, *compose;
 	int ret = 0;
 
-	if (sel->pad >= CSI_NUM_PADS || sel->pad == CSI_SINK_PAD)
+	if (sel->pad != CSI_SINK_PAD)
 		return -EINVAL;
 
 	mutex_lock(&priv->lock);
 
 	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
-	if (!infmt) {
-		ret = -EINVAL;
-		goto out;
-	}
+	crop = __csi_get_crop(priv, cfg, sel->which);
+	compose = __csi_get_compose(priv, cfg, sel->which);
 
 	switch (sel->target) {
 	case V4L2_SEL_TGT_CROP_BOUNDS:
@@ -1335,36 +1362,54 @@ static int csi_get_selection(struct v4l2_subdev *sd,
 		sel->r.height = infmt->height;
 		break;
 	case V4L2_SEL_TGT_CROP:
-		if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
-			struct v4l2_rect *try_crop =
-				v4l2_subdev_get_try_crop(&priv->sd,
-							 cfg, sel->pad);
-			sel->r = *try_crop;
-		} else {
-			sel->r = priv->crop;
-		}
+		sel->r = *crop;
+		break;
+	case V4L2_SEL_TGT_COMPOSE_BOUNDS:
+		sel->r.left = 0;
+		sel->r.top = 0;
+		sel->r.width = crop->width;
+		sel->r.height = crop->height;
+		break;
+	case V4L2_SEL_TGT_COMPOSE:
+		sel->r = *compose;
 		break;
 	default:
 		ret = -EINVAL;
 	}
 
-out:
 	mutex_unlock(&priv->lock);
 	return ret;
 }
 
+static int csi_set_scale(u32 *compose, u32 crop, u32 flags)
+{
+	if ((flags & (V4L2_SEL_FLAG_LE | V4L2_SEL_FLAG_GE)) ==
+		     (V4L2_SEL_FLAG_LE | V4L2_SEL_FLAG_GE) &&
+	    *compose != crop && *compose != crop / 2)
+		return -ERANGE;
+
+	if (*compose <= crop / 2 ||
+	    (*compose < crop * 3 / 4 && !(flags & V4L2_SEL_FLAG_GE)) ||
+	    (*compose < crop && (flags & V4L2_SEL_FLAG_LE)))
+		*compose = crop / 2;
+	else
+		*compose = crop;
+
+	return 0;
+}
+
 static int csi_set_selection(struct v4l2_subdev *sd,
 			     struct v4l2_subdev_pad_config *cfg,
 			     struct v4l2_subdev_selection *sel)
 {
 	struct csi_priv *priv = v4l2_get_subdevdata(sd);
 	struct v4l2_mbus_framefmt *infmt;
+	struct v4l2_rect *crop, *compose;
 	struct imx_media_subdev *sensor;
+	int pad;
 	int ret = 0;
 
-	if (sel->pad >= CSI_NUM_PADS ||
-	    sel->pad == CSI_SINK_PAD ||
-	    sel->target != V4L2_SEL_TGT_CROP)
+	if (sel->pad != CSI_SINK_PAD)
 		return -EINVAL;
 
 	sensor = imx_media_find_sensor(priv->md, &priv->sd.entity);
@@ -1380,31 +1425,68 @@ static int csi_set_selection(struct v4l2_subdev *sd,
 		goto out;
 	}
 
-	/*
-	 * Modifying the crop rectangle always changes the format on the source
-	 * pad. If the KEEP_CONFIG flag is set, just return the current crop
-	 * rectangle.
-	 */
-	if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
-		sel->r = priv->crop;
-		if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
-			cfg->try_crop = sel->r;
+	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
+	crop = __csi_get_crop(priv, cfg, sel->which);
+	compose = __csi_get_compose(priv, cfg, sel->which);
+
+	switch (sel->target) {
+	case V4L2_SEL_TGT_CROP:
+		/*
+		 * Modifying the crop rectangle always changes the format on
+		 * the source pads. If the KEEP_CONFIG flag is set, just return
+		 * the current crop rectangle.
+		 */
+		if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
+			sel->r = priv->crop;
+			if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
+				*crop = sel->r;
+			goto out;
+		}
+
+		csi_try_crop(priv, &sel->r, cfg, infmt, sensor);
+
+		*crop = sel->r;
+
+		/* Reset scaling to 1:1 */
+		compose->width = crop->width;
+		compose->height = crop->height;
+		break;
+	case V4L2_SEL_TGT_COMPOSE:
+		/*
+		 * Modifying the compose rectangle always changes the format on
+		 * the source pads. If the KEEP_CONFIG flag is set, just return
+		 * the current compose rectangle.
+		 */
+		if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
+			sel->r = priv->compose;
+			if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
+				*compose = sel->r;
+			goto out;
+		}
+
+		sel->r.left = 0;
+		sel->r.top = 0;
+		ret = csi_set_scale(&sel->r.width, crop->width, sel->flags);
+		if (ret)
+			goto out;
+		ret = csi_set_scale(&sel->r.height, crop->height, sel->flags);
+		if (ret)
+			goto out;
+
+		*compose = sel->r;
+		break;
+	default:
+		ret = -EINVAL;
 		goto out;
 	}
 
-	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
-	csi_try_crop(priv, &sel->r, cfg, infmt, sensor);
-
-	if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
-		cfg->try_crop = sel->r;
-	} else {
-		struct v4l2_mbus_framefmt *outfmt =
-			&priv->format_mbus[sel->pad];
+	/* Reset source pads to sink compose rectangle */
+	for (pad = CSI_SINK_PAD + 1; pad < CSI_NUM_PADS; pad++) {
+		struct v4l2_mbus_framefmt *outfmt;
 
-		priv->crop = sel->r;
-		/* Update the source format */
-		outfmt->width = sel->r.width;
-		outfmt->height = sel->r.height;
+		outfmt = __csi_get_fmt(priv, cfg, pad, sel->which);
+		outfmt->width = compose->width;
+		outfmt->height = compose->height;
 	}
 
 out:
@@ -1467,6 +1549,12 @@ static int csi_registered(struct v4l2_subdev *sd)
 			priv->skip[i - 1] = &csi_skip[0];
 	}
 
+	/* init default crop and compose rectangle sizes */
+	priv->crop.width = 640;
+	priv->crop.height = 480;
+	priv->compose.width = 640;
+	priv->compose.height = 480;
+
 	/* init default frame interval */
 	priv->frame_interval.numerator = 1;
 	priv->frame_interval.denominator = 30;
-- 
2.11.0
---------->8----------

regards
Philipp

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 06:23:24PM +0100, Philipp Zabel wrote:
> ----------8<----------
> >From 2830aebc404bdfc9d7fc1ec94e5282d0b668e8f6 Mon Sep 17 00:00:00 2001
> From: Philipp Zabel <p.zabel@pengutronix.de>
> Date: Mon, 20 Mar 2017 17:10:21 +0100
> Subject: [PATCH] media: imx: csi: add sink selection rectangles
> 
> Move the crop rectangle to the sink pad and add a sink compose rectangle
> to configure scaling. Also propagate rectangles from sink pad to crop
> rectangle, to compose rectangle, and to the source pads both in ACTIVE
> and TRY variants of set_fmt/selection, and initialize the default crop
> and compose rectangles.

Looks fine for the most part.

> -	/*
> -	 * Modifying the crop rectangle always changes the format on the source
> -	 * pad. If the KEEP_CONFIG flag is set, just return the current crop
> -	 * rectangle.
> -	 */
> -	if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
> -		sel->r = priv->crop;
> -		if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
> -			cfg->try_crop = sel->r;
> +	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
> +	crop = __csi_get_crop(priv, cfg, sel->which);
> +	compose = __csi_get_compose(priv, cfg, sel->which);
> +
> +	switch (sel->target) {
> +	case V4L2_SEL_TGT_CROP:
> +		/*
> +		 * Modifying the crop rectangle always changes the format on
> +		 * the source pads. If the KEEP_CONFIG flag is set, just return
> +		 * the current crop rectangle.
> +		 */
> +		if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
> +			sel->r = priv->crop;

My understanding of KEEP_CONFIG is that the only thing we're not
allowed to do is to propagate the change downstream.

Since downstream of the crop is the compose, that means the only
restriction here is that the width and height of the crop window must
be either equal to the compose width/height, or double the compose
width/height.  (Anything else would necessitate the compose window
changing.)

However, the crop window can move position within the crop bounds,
provided it's entirely contained within those crop bounds.

The problem is that this becomes rather more complex it deal with
(as I'm finding out in my imx219 camera driver) and I'm thinking
that some of this complexity should probably be in a helper in
generic v4l2 code.

I don't know whether this applies (I hope it doesn't) but there's a
pile of guidelines in Documentation/media/uapi/v4l/vidioc-g-selection.rst
which describe how a crop/compose rectangle should be adjusted.  As
I say, I hope they don't apply, because if they do, we would _really_
need helpers for this stuff, as I don't think having each driver
implement all these rules would be too successful!

> +			if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
> +				*crop = sel->r;
> +			goto out;
> +		}
> +
> +		csi_try_crop(priv, &sel->r, cfg, infmt, sensor);
> +
> +		*crop = sel->r;
> +
> +		/* Reset scaling to 1:1 */
> +		compose->width = crop->width;
> +		compose->height = crop->height;
> +		break;
> +	case V4L2_SEL_TGT_COMPOSE:
> +		/*
> +		 * Modifying the compose rectangle always changes the format on
> +		 * the source pads. If the KEEP_CONFIG flag is set, just return
> +		 * the current compose rectangle.
> +		 */
> +		if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
> +			sel->r = priv->compose;

I think, with my understanding of how the KEEP_CONFIG flag works, this
should be:
			sel->r = *compose;

because if we change the compose rectangle width/height, we would need
to propagate this to the source pad, and the KEEP_CONFIG description
says we're not allowed to do that.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 06:23:24PM +0100, Philipp Zabel wrote:
> ----------8<----------
> >From 2830aebc404bdfc9d7fc1ec94e5282d0b668e8f6 Mon Sep 17 00:00:00 2001
> From: Philipp Zabel <p.zabel@pengutronix.de>
> Date: Mon, 20 Mar 2017 17:10:21 +0100
> Subject: [PATCH] media: imx: csi: add sink selection rectangles
> 
> Move the crop rectangle to the sink pad and add a sink compose rectangle
> to configure scaling. Also propagate rectangles from sink pad to crop
> rectangle, to compose rectangle, and to the source pads both in ACTIVE
> and TRY variants of set_fmt/selection, and initialize the default crop
> and compose rectangles.

Looks fine for the most part.

> -	/*
> -	 * Modifying the crop rectangle always changes the format on the source
> -	 * pad. If the KEEP_CONFIG flag is set, just return the current crop
> -	 * rectangle.
> -	 */
> -	if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
> -		sel->r = priv->crop;
> -		if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
> -			cfg->try_crop = sel->r;
> +	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
> +	crop = __csi_get_crop(priv, cfg, sel->which);
> +	compose = __csi_get_compose(priv, cfg, sel->which);
> +
> +	switch (sel->target) {
> +	case V4L2_SEL_TGT_CROP:
> +		/*
> +		 * Modifying the crop rectangle always changes the format on
> +		 * the source pads. If the KEEP_CONFIG flag is set, just return
> +		 * the current crop rectangle.
> +		 */
> +		if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
> +			sel->r = priv->crop;

My understanding of KEEP_CONFIG is that the only thing we're not
allowed to do is to propagate the change downstream.

Since downstream of the crop is the compose, that means the only
restriction here is that the width and height of the crop window must
be either equal to the compose width/height, or double the compose
width/height.  (Anything else would necessitate the compose window
changing.)

However, the crop window can move position within the crop bounds,
provided it's entirely contained within those crop bounds.

The problem is that this becomes rather more complex it deal with
(as I'm finding out in my imx219 camera driver) and I'm thinking
that some of this complexity should probably be in a helper in
generic v4l2 code.

I don't know whether this applies (I hope it doesn't) but there's a
pile of guidelines in Documentation/media/uapi/v4l/vidioc-g-selection.rst
which describe how a crop/compose rectangle should be adjusted.  As
I say, I hope they don't apply, because if they do, we would _really_
need helpers for this stuff, as I don't think having each driver
implement all these rules would be too successful!

> +			if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
> +				*crop = sel->r;
> +			goto out;
> +		}
> +
> +		csi_try_crop(priv, &sel->r, cfg, infmt, sensor);
> +
> +		*crop = sel->r;
> +
> +		/* Reset scaling to 1:1 */
> +		compose->width = crop->width;
> +		compose->height = crop->height;
> +		break;
> +	case V4L2_SEL_TGT_COMPOSE:
> +		/*
> +		 * Modifying the compose rectangle always changes the format on
> +		 * the source pads. If the KEEP_CONFIG flag is set, just return
> +		 * the current compose rectangle.
> +		 */
> +		if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
> +			sel->r = priv->compose;

I think, with my understanding of how the KEEP_CONFIG flag works, this
should be:
			sel->r = *compose;

because if we change the compose rectangle width/height, we would need
to propagate this to the source pad, and the KEEP_CONFIG description
says we're not allowed to do that.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 06:23:24PM +0100, Philipp Zabel wrote:
> ----------8<----------
> >From 2830aebc404bdfc9d7fc1ec94e5282d0b668e8f6 Mon Sep 17 00:00:00 2001
> From: Philipp Zabel <p.zabel@pengutronix.de>
> Date: Mon, 20 Mar 2017 17:10:21 +0100
> Subject: [PATCH] media: imx: csi: add sink selection rectangles
> 
> Move the crop rectangle to the sink pad and add a sink compose rectangle
> to configure scaling. Also propagate rectangles from sink pad to crop
> rectangle, to compose rectangle, and to the source pads both in ACTIVE
> and TRY variants of set_fmt/selection, and initialize the default crop
> and compose rectangles.

Looks fine for the most part.

> -	/*
> -	 * Modifying the crop rectangle always changes the format on the source
> -	 * pad. If the KEEP_CONFIG flag is set, just return the current crop
> -	 * rectangle.
> -	 */
> -	if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
> -		sel->r = priv->crop;
> -		if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
> -			cfg->try_crop = sel->r;
> +	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
> +	crop = __csi_get_crop(priv, cfg, sel->which);
> +	compose = __csi_get_compose(priv, cfg, sel->which);
> +
> +	switch (sel->target) {
> +	case V4L2_SEL_TGT_CROP:
> +		/*
> +		 * Modifying the crop rectangle always changes the format on
> +		 * the source pads. If the KEEP_CONFIG flag is set, just return
> +		 * the current crop rectangle.
> +		 */
> +		if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
> +			sel->r = priv->crop;

My understanding of KEEP_CONFIG is that the only thing we're not
allowed to do is to propagate the change downstream.

Since downstream of the crop is the compose, that means the only
restriction here is that the width and height of the crop window must
be either equal to the compose width/height, or double the compose
width/height.  (Anything else would necessitate the compose window
changing.)

However, the crop window can move position within the crop bounds,
provided it's entirely contained within those crop bounds.

The problem is that this becomes rather more complex it deal with
(as I'm finding out in my imx219 camera driver) and I'm thinking
that some of this complexity should probably be in a helper in
generic v4l2 code.

I don't know whether this applies (I hope it doesn't) but there's a
pile of guidelines in Documentation/media/uapi/v4l/vidioc-g-selection.rst
which describe how a crop/compose rectangle should be adjusted.  As
I say, I hope they don't apply, because if they do, we would _really_
need helpers for this stuff, as I don't think having each driver
implement all these rules would be too successful!

> +			if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
> +				*crop = sel->r;
> +			goto out;
> +		}
> +
> +		csi_try_crop(priv, &sel->r, cfg, infmt, sensor);
> +
> +		*crop = sel->r;
> +
> +		/* Reset scaling to 1:1 */
> +		compose->width = crop->width;
> +		compose->height = crop->height;
> +		break;
> +	case V4L2_SEL_TGT_COMPOSE:
> +		/*
> +		 * Modifying the compose rectangle always changes the format on
> +		 * the source pads. If the KEEP_CONFIG flag is set, just return
> +		 * the current compose rectangle.
> +		 */
> +		if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
> +			sel->r = priv->compose;

I think, with my understanding of how the KEEP_CONFIG flag works, this
should be:
			sel->r = *compose;

because if we change the compose rectangle width/height, we would need
to propagate this to the source pad, and the KEEP_CONFIG description
says we're not allowed to do that.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Steve Longerbeam]

On 03/20/2017 10:23 AM, Philipp Zabel wrote:
> Hi Steve, Russell,
>
> On Mon, 2017-03-20 at 14:17 +0000, Russell King - ARM Linux wrote:
>> On Mon, Mar 20, 2017 at 03:00:51PM +0100, Philipp Zabel wrote:
>>> On Mon, 2017-03-20 at 12:08 +0000, Russell King - ARM Linux wrote:
>>>> The same document says:
>>>>
>>>>   Scaling support is optional. When supported by a subdev, the crop
>>>>   rectangle on the subdev's sink pad is scaled to the size configured
>>>>   using the
>>>>   :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
>>>>   using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
>>>>   subdev supports scaling but not composing, the top and left values are
>>>>   not used and must always be set to zero.
>>>
>>> Right, this sentence does imply that when scaling is supported, there
>>> must be a sink compose rectangle, even when composing is not.
>>>
>>> I have previously set up scaling like this:
>>>
>>> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
>>> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
>>>
>>> Does this mean, it should work like this instead?
>>>
>>> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
>>> media-ctl --set-v4l2 "'ipu1_csi0':0[fmt:UYVY2X8/1920x1080@1/60,compose:(0,0)/960x540]"
>>> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
>>>
>>> I suppose setting the source pad format should not be allowed to modify
>>> the sink compose rectangle.
>>
>> That is what I believe having read these documents several times, but
>> we need v4l2 people to confirm.
>
> What do you think of this:
>
> ----------8<----------
> From 2830aebc404bdfc9d7fc1ec94e5282d0b668e8f6 Mon Sep 17 00:00:00 2001
> From: Philipp Zabel <p.zabel@pengutronix.de>
> Date: Mon, 20 Mar 2017 17:10:21 +0100
> Subject: [PATCH] media: imx: csi: add sink selection rectangles
>
> Move the crop rectangle to the sink pad and add a sink compose rectangle
> to configure scaling. Also propagate rectangles from sink pad to crop
> rectangle, to compose rectangle, and to the source pads both in ACTIVE
> and TRY variants of set_fmt/selection, and initialize the default crop
> and compose rectangles.
>

I haven't had a chance to look at this patch in detail yet, but on
first glance it looks good to me. I'll try to find the time tomorrow
to incorporate it and then fixup Russell's subsequent patches for
the enum frame sizes/intervals.

Steve

> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
> ---
>  drivers/staging/media/imx/imx-media-csi.c | 216 +++++++++++++++++++++---------
>  1 file changed, 152 insertions(+), 64 deletions(-)
>
> diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
> index 560da3abdd70b..b026a5d602ddf 100644
> --- a/drivers/staging/media/imx/imx-media-csi.c
> +++ b/drivers/staging/media/imx/imx-media-csi.c
> @@ -79,6 +79,7 @@ struct csi_priv {
>  	const struct imx_media_pixfmt *cc[CSI_NUM_PADS];
>  	struct v4l2_fract frame_interval;
>  	struct v4l2_rect crop;
> +	struct v4l2_rect compose;
>  	const struct csi_skip_desc *skip[CSI_NUM_PADS - 1];
>
>  	/* active vb2 buffers to send to video dev sink */
> @@ -574,8 +575,8 @@ static int csi_setup(struct csi_priv *priv)
>  	ipu_csi_set_window(priv->csi, &priv->crop);
>
>  	ipu_csi_set_downsize(priv->csi,
> -			     priv->crop.width == 2 * outfmt->width,
> -			     priv->crop.height == 2 * outfmt->height);
> +			     priv->crop.width == 2 * priv->compose.width,
> +			     priv->crop.height == 2 * priv->compose.height);
>
>  	ipu_csi_init_interface(priv->csi, &sensor_mbus_cfg, &if_fmt);
>
> @@ -1001,6 +1002,27 @@ __csi_get_fmt(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
>  		return &priv->format_mbus[pad];
>  }
>
> +static struct v4l2_rect *
> +__csi_get_crop(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
> +	       enum v4l2_subdev_format_whence which)
> +{
> +	if (which == V4L2_SUBDEV_FORMAT_TRY)
> +		return v4l2_subdev_get_try_crop(&priv->sd, cfg, CSI_SINK_PAD);
> +	else
> +		return &priv->crop;
> +}
> +
> +static struct v4l2_rect *
> +__csi_get_compose(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
> +		  enum v4l2_subdev_format_whence which)
> +{
> +	if (which == V4L2_SUBDEV_FORMAT_TRY)
> +		return v4l2_subdev_get_try_compose(&priv->sd, cfg,
> +						   CSI_SINK_PAD);
> +	else
> +		return &priv->compose;
> +}
> +
>  static void csi_try_crop(struct csi_priv *priv,
>  			 struct v4l2_rect *crop,
>  			 struct v4l2_subdev_pad_config *cfg,
> @@ -1159,6 +1181,7 @@ static void csi_try_fmt(struct csi_priv *priv,
>  			struct v4l2_subdev_pad_config *cfg,
>  			struct v4l2_subdev_format *sdformat,
>  			struct v4l2_rect *crop,
> +			struct v4l2_rect *compose,
>  			const struct imx_media_pixfmt **cc)
>  {
>  	const struct imx_media_pixfmt *incc;
> @@ -1173,15 +1196,8 @@ static void csi_try_fmt(struct csi_priv *priv,
>  		incc = imx_media_find_mbus_format(infmt->code,
>  						  CS_SEL_ANY, true);
>
> -		if (sdformat->format.width < priv->crop.width * 3 / 4)
> -			sdformat->format.width = priv->crop.width / 2;
> -		else
> -			sdformat->format.width = priv->crop.width;
> -
> -		if (sdformat->format.height < priv->crop.height * 3 / 4)
> -			sdformat->format.height = priv->crop.height / 2;
> -		else
> -			sdformat->format.height = priv->crop.height;
> +		sdformat->format.width = compose->width;
> +		sdformat->format.height = compose->height;
>
>  		if (incc->bayer) {
>  			sdformat->format.code = infmt->code;
> @@ -1217,11 +1233,17 @@ static void csi_try_fmt(struct csi_priv *priv,
>  		v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
>  				      W_ALIGN, &sdformat->format.height,
>  				      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
> +
> +		/* Reset crop and compose rectangles */
>  		crop->left = 0;
>  		crop->top = 0;
>  		crop->width = sdformat->format.width;
>  		crop->height = sdformat->format.height;
>  		csi_try_crop(priv, crop, cfg, &sdformat->format, sensor);
> +		compose->left = 0;
> +		compose->top = 0;
> +		compose->width = crop->width;
> +		compose->height = crop->height;
>
>  		*cc = imx_media_find_mbus_format(sdformat->format.code,
>  						 CS_SEL_ANY, true);
> @@ -1245,7 +1267,8 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
>  	const struct imx_media_pixfmt *cc;
>  	struct imx_media_subdev *sensor;
>  	struct v4l2_pix_format vdev_fmt;
> -	struct v4l2_rect crop;
> +	struct v4l2_mbus_framefmt *fmt;
> +	struct v4l2_rect *crop, *compose;
>  	int ret = 0;
>
>  	if (sdformat->pad >= CSI_NUM_PADS)
> @@ -1264,37 +1287,42 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
>  		goto out;
>  	}
>
> -	csi_try_fmt(priv, sensor, cfg, sdformat, &crop, &cc);
> +	crop = __csi_get_crop(priv, cfg, sdformat->which);
> +	compose = __csi_get_compose(priv, cfg, sdformat->which);
>
> -	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
> -		cfg->try_fmt = sdformat->format;
> -		goto out;
> -	}
> +	csi_try_fmt(priv, sensor, cfg, sdformat, crop, compose, &cc);
>
> -	priv->format_mbus[sdformat->pad] = sdformat->format;
> -	priv->cc[sdformat->pad] = cc;
> +	fmt = __csi_get_fmt(priv, cfg, sdformat->pad, sdformat->which);
> +	*fmt = sdformat->format;
>
>  	if (sdformat->pad == CSI_SINK_PAD) {
>  		int pad;
>
> -		/* reset the crop window */
> -		priv->crop = crop;
> -
>  		/* propagate format to source pads */
>  		for (pad = CSI_SINK_PAD + 1; pad < CSI_NUM_PADS; pad++) {
>  			const struct imx_media_pixfmt *outcc;
>  			struct v4l2_subdev_format format;
> +			struct v4l2_mbus_framefmt *outfmt;
>
>  			format.pad = pad;
> -			format.which = V4L2_SUBDEV_FORMAT_ACTIVE;
> +			format.which = sdformat->which;
>  			format.format = sdformat->format;
> -			csi_try_fmt(priv, sensor, cfg, &format, &crop, &outcc);
> +			csi_try_fmt(priv, sensor, cfg, &format, NULL, compose,
> +				    &outcc);
>
> -			priv->format_mbus[pad] = format.format;
> -			priv->cc[pad] = outcc;
> +			outfmt = __csi_get_fmt(priv, cfg, pad, sdformat->which);
> +			*outfmt = format.format;
> +
> +			if (sdformat->which == V4L2_SUBDEV_FORMAT_ACTIVE)
> +				priv->cc[pad] = outcc;
>  		}
>  	}
>
> +	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY)
> +		goto out;
> +
> +	priv->cc[sdformat->pad] = cc;
> +
>  	/* propagate IDMAC output pad format to capture device */
>  	imx_media_mbus_fmt_to_pix_fmt(&vdev_fmt,
>  				      &priv->format_mbus[CSI_SRC_PAD_IDMAC],
> @@ -1314,18 +1342,17 @@ static int csi_get_selection(struct v4l2_subdev *sd,
>  {
>  	struct csi_priv *priv = v4l2_get_subdevdata(sd);
>  	struct v4l2_mbus_framefmt *infmt;
> +	struct v4l2_rect *crop, *compose;
>  	int ret = 0;
>
> -	if (sel->pad >= CSI_NUM_PADS || sel->pad == CSI_SINK_PAD)
> +	if (sel->pad != CSI_SINK_PAD)
>  		return -EINVAL;
>
>  	mutex_lock(&priv->lock);
>
>  	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
> -	if (!infmt) {
> -		ret = -EINVAL;
> -		goto out;
> -	}
> +	crop = __csi_get_crop(priv, cfg, sel->which);
> +	compose = __csi_get_compose(priv, cfg, sel->which);
>
>  	switch (sel->target) {
>  	case V4L2_SEL_TGT_CROP_BOUNDS:
> @@ -1335,36 +1362,54 @@ static int csi_get_selection(struct v4l2_subdev *sd,
>  		sel->r.height = infmt->height;
>  		break;
>  	case V4L2_SEL_TGT_CROP:
> -		if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
> -			struct v4l2_rect *try_crop =
> -				v4l2_subdev_get_try_crop(&priv->sd,
> -							 cfg, sel->pad);
> -			sel->r = *try_crop;
> -		} else {
> -			sel->r = priv->crop;
> -		}
> +		sel->r = *crop;
> +		break;
> +	case V4L2_SEL_TGT_COMPOSE_BOUNDS:
> +		sel->r.left = 0;
> +		sel->r.top = 0;
> +		sel->r.width = crop->width;
> +		sel->r.height = crop->height;
> +		break;
> +	case V4L2_SEL_TGT_COMPOSE:
> +		sel->r = *compose;
>  		break;
>  	default:
>  		ret = -EINVAL;
>  	}
>
> -out:
>  	mutex_unlock(&priv->lock);
>  	return ret;
>  }
>
> +static int csi_set_scale(u32 *compose, u32 crop, u32 flags)
> +{
> +	if ((flags & (V4L2_SEL_FLAG_LE | V4L2_SEL_FLAG_GE)) ==
> +		     (V4L2_SEL_FLAG_LE | V4L2_SEL_FLAG_GE) &&
> +	    *compose != crop && *compose != crop / 2)
> +		return -ERANGE;
> +
> +	if (*compose <= crop / 2 ||
> +	    (*compose < crop * 3 / 4 && !(flags & V4L2_SEL_FLAG_GE)) ||
> +	    (*compose < crop && (flags & V4L2_SEL_FLAG_LE)))
> +		*compose = crop / 2;
> +	else
> +		*compose = crop;
> +
> +	return 0;
> +}
> +
>  static int csi_set_selection(struct v4l2_subdev *sd,
>  			     struct v4l2_subdev_pad_config *cfg,
>  			     struct v4l2_subdev_selection *sel)
>  {
>  	struct csi_priv *priv = v4l2_get_subdevdata(sd);
>  	struct v4l2_mbus_framefmt *infmt;
> +	struct v4l2_rect *crop, *compose;
>  	struct imx_media_subdev *sensor;
> +	int pad;
>  	int ret = 0;
>
> -	if (sel->pad >= CSI_NUM_PADS ||
> -	    sel->pad == CSI_SINK_PAD ||
> -	    sel->target != V4L2_SEL_TGT_CROP)
> +	if (sel->pad != CSI_SINK_PAD)
>  		return -EINVAL;
>
>  	sensor = imx_media_find_sensor(priv->md, &priv->sd.entity);
> @@ -1380,31 +1425,68 @@ static int csi_set_selection(struct v4l2_subdev *sd,
>  		goto out;
>  	}
>
> -	/*
> -	 * Modifying the crop rectangle always changes the format on the source
> -	 * pad. If the KEEP_CONFIG flag is set, just return the current crop
> -	 * rectangle.
> -	 */
> -	if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
> -		sel->r = priv->crop;
> -		if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
> -			cfg->try_crop = sel->r;
> +	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
> +	crop = __csi_get_crop(priv, cfg, sel->which);
> +	compose = __csi_get_compose(priv, cfg, sel->which);
> +
> +	switch (sel->target) {
> +	case V4L2_SEL_TGT_CROP:
> +		/*
> +		 * Modifying the crop rectangle always changes the format on
> +		 * the source pads. If the KEEP_CONFIG flag is set, just return
> +		 * the current crop rectangle.
> +		 */
> +		if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
> +			sel->r = priv->crop;
> +			if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
> +				*crop = sel->r;
> +			goto out;
> +		}
> +
> +		csi_try_crop(priv, &sel->r, cfg, infmt, sensor);
> +
> +		*crop = sel->r;
> +
> +		/* Reset scaling to 1:1 */
> +		compose->width = crop->width;
> +		compose->height = crop->height;
> +		break;
> +	case V4L2_SEL_TGT_COMPOSE:
> +		/*
> +		 * Modifying the compose rectangle always changes the format on
> +		 * the source pads. If the KEEP_CONFIG flag is set, just return
> +		 * the current compose rectangle.
> +		 */
> +		if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
> +			sel->r = priv->compose;
> +			if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
> +				*compose = sel->r;
> +			goto out;
> +		}
> +
> +		sel->r.left = 0;
> +		sel->r.top = 0;
> +		ret = csi_set_scale(&sel->r.width, crop->width, sel->flags);
> +		if (ret)
> +			goto out;
> +		ret = csi_set_scale(&sel->r.height, crop->height, sel->flags);
> +		if (ret)
> +			goto out;
> +
> +		*compose = sel->r;
> +		break;
> +	default:
> +		ret = -EINVAL;
>  		goto out;
>  	}
>
> -	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
> -	csi_try_crop(priv, &sel->r, cfg, infmt, sensor);
> -
> -	if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
> -		cfg->try_crop = sel->r;
> -	} else {
> -		struct v4l2_mbus_framefmt *outfmt =
> -			&priv->format_mbus[sel->pad];
> +	/* Reset source pads to sink compose rectangle */
> +	for (pad = CSI_SINK_PAD + 1; pad < CSI_NUM_PADS; pad++) {
> +		struct v4l2_mbus_framefmt *outfmt;
>
> -		priv->crop = sel->r;
> -		/* Update the source format */
> -		outfmt->width = sel->r.width;
> -		outfmt->height = sel->r.height;
> +		outfmt = __csi_get_fmt(priv, cfg, pad, sel->which);
> +		outfmt->width = compose->width;
> +		outfmt->height = compose->height;
>  	}
>
>  out:
> @@ -1467,6 +1549,12 @@ static int csi_registered(struct v4l2_subdev *sd)
>  			priv->skip[i - 1] = &csi_skip[0];
>  	}
>
> +	/* init default crop and compose rectangle sizes */
> +	priv->crop.width = 640;
> +	priv->crop.height = 480;
> +	priv->compose.width = 640;
> +	priv->compose.height = 480;
> +
>  	/* init default frame interval */
>  	priv->frame_interval.numerator = 1;
>  	priv->frame_interval.denominator = 30;
>

[PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Steve Longerbeam]

On 03/20/2017 10:23 AM, Philipp Zabel wrote:
> Hi Steve, Russell,
>
> On Mon, 2017-03-20 at 14:17 +0000, Russell King - ARM Linux wrote:
>> On Mon, Mar 20, 2017 at 03:00:51PM +0100, Philipp Zabel wrote:
>>> On Mon, 2017-03-20 at 12:08 +0000, Russell King - ARM Linux wrote:
>>>> The same document says:
>>>>
>>>>   Scaling support is optional. When supported by a subdev, the crop
>>>>   rectangle on the subdev's sink pad is scaled to the size configured
>>>>   using the
>>>>   :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
>>>>   using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
>>>>   subdev supports scaling but not composing, the top and left values are
>>>>   not used and must always be set to zero.
>>>
>>> Right, this sentence does imply that when scaling is supported, there
>>> must be a sink compose rectangle, even when composing is not.
>>>
>>> I have previously set up scaling like this:
>>>
>>> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080 at 1/60]"
>>> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540 at 1/30]"
>>>
>>> Does this mean, it should work like this instead?
>>>
>>> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080 at 1/60]"
>>> media-ctl --set-v4l2 "'ipu1_csi0':0[fmt:UYVY2X8/1920x1080 at 1/60,compose:(0,0)/960x540]"
>>> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540 at 1/30]"
>>>
>>> I suppose setting the source pad format should not be allowed to modify
>>> the sink compose rectangle.
>>
>> That is what I believe having read these documents several times, but
>> we need v4l2 people to confirm.
>
> What do you think of this:
>
> ----------8<----------
> From 2830aebc404bdfc9d7fc1ec94e5282d0b668e8f6 Mon Sep 17 00:00:00 2001
> From: Philipp Zabel <p.zabel@pengutronix.de>
> Date: Mon, 20 Mar 2017 17:10:21 +0100
> Subject: [PATCH] media: imx: csi: add sink selection rectangles
>
> Move the crop rectangle to the sink pad and add a sink compose rectangle
> to configure scaling. Also propagate rectangles from sink pad to crop
> rectangle, to compose rectangle, and to the source pads both in ACTIVE
> and TRY variants of set_fmt/selection, and initialize the default crop
> and compose rectangles.
>

I haven't had a chance to look at this patch in detail yet, but on
first glance it looks good to me. I'll try to find the time tomorrow
to incorporate it and then fixup Russell's subsequent patches for
the enum frame sizes/intervals.

Steve

> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
> ---
>  drivers/staging/media/imx/imx-media-csi.c | 216 +++++++++++++++++++++---------
>  1 file changed, 152 insertions(+), 64 deletions(-)
>
> diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
> index 560da3abdd70b..b026a5d602ddf 100644
> --- a/drivers/staging/media/imx/imx-media-csi.c
> +++ b/drivers/staging/media/imx/imx-media-csi.c
> @@ -79,6 +79,7 @@ struct csi_priv {
>  	const struct imx_media_pixfmt *cc[CSI_NUM_PADS];
>  	struct v4l2_fract frame_interval;
>  	struct v4l2_rect crop;
> +	struct v4l2_rect compose;
>  	const struct csi_skip_desc *skip[CSI_NUM_PADS - 1];
>
>  	/* active vb2 buffers to send to video dev sink */
> @@ -574,8 +575,8 @@ static int csi_setup(struct csi_priv *priv)
>  	ipu_csi_set_window(priv->csi, &priv->crop);
>
>  	ipu_csi_set_downsize(priv->csi,
> -			     priv->crop.width == 2 * outfmt->width,
> -			     priv->crop.height == 2 * outfmt->height);
> +			     priv->crop.width == 2 * priv->compose.width,
> +			     priv->crop.height == 2 * priv->compose.height);
>
>  	ipu_csi_init_interface(priv->csi, &sensor_mbus_cfg, &if_fmt);
>
> @@ -1001,6 +1002,27 @@ __csi_get_fmt(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
>  		return &priv->format_mbus[pad];
>  }
>
> +static struct v4l2_rect *
> +__csi_get_crop(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
> +	       enum v4l2_subdev_format_whence which)
> +{
> +	if (which == V4L2_SUBDEV_FORMAT_TRY)
> +		return v4l2_subdev_get_try_crop(&priv->sd, cfg, CSI_SINK_PAD);
> +	else
> +		return &priv->crop;
> +}
> +
> +static struct v4l2_rect *
> +__csi_get_compose(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
> +		  enum v4l2_subdev_format_whence which)
> +{
> +	if (which == V4L2_SUBDEV_FORMAT_TRY)
> +		return v4l2_subdev_get_try_compose(&priv->sd, cfg,
> +						   CSI_SINK_PAD);
> +	else
> +		return &priv->compose;
> +}
> +
>  static void csi_try_crop(struct csi_priv *priv,
>  			 struct v4l2_rect *crop,
>  			 struct v4l2_subdev_pad_config *cfg,
> @@ -1159,6 +1181,7 @@ static void csi_try_fmt(struct csi_priv *priv,
>  			struct v4l2_subdev_pad_config *cfg,
>  			struct v4l2_subdev_format *sdformat,
>  			struct v4l2_rect *crop,
> +			struct v4l2_rect *compose,
>  			const struct imx_media_pixfmt **cc)
>  {
>  	const struct imx_media_pixfmt *incc;
> @@ -1173,15 +1196,8 @@ static void csi_try_fmt(struct csi_priv *priv,
>  		incc = imx_media_find_mbus_format(infmt->code,
>  						  CS_SEL_ANY, true);
>
> -		if (sdformat->format.width < priv->crop.width * 3 / 4)
> -			sdformat->format.width = priv->crop.width / 2;
> -		else
> -			sdformat->format.width = priv->crop.width;
> -
> -		if (sdformat->format.height < priv->crop.height * 3 / 4)
> -			sdformat->format.height = priv->crop.height / 2;
> -		else
> -			sdformat->format.height = priv->crop.height;
> +		sdformat->format.width = compose->width;
> +		sdformat->format.height = compose->height;
>
>  		if (incc->bayer) {
>  			sdformat->format.code = infmt->code;
> @@ -1217,11 +1233,17 @@ static void csi_try_fmt(struct csi_priv *priv,
>  		v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
>  				      W_ALIGN, &sdformat->format.height,
>  				      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
> +
> +		/* Reset crop and compose rectangles */
>  		crop->left = 0;
>  		crop->top = 0;
>  		crop->width = sdformat->format.width;
>  		crop->height = sdformat->format.height;
>  		csi_try_crop(priv, crop, cfg, &sdformat->format, sensor);
> +		compose->left = 0;
> +		compose->top = 0;
> +		compose->width = crop->width;
> +		compose->height = crop->height;
>
>  		*cc = imx_media_find_mbus_format(sdformat->format.code,
>  						 CS_SEL_ANY, true);
> @@ -1245,7 +1267,8 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
>  	const struct imx_media_pixfmt *cc;
>  	struct imx_media_subdev *sensor;
>  	struct v4l2_pix_format vdev_fmt;
> -	struct v4l2_rect crop;
> +	struct v4l2_mbus_framefmt *fmt;
> +	struct v4l2_rect *crop, *compose;
>  	int ret = 0;
>
>  	if (sdformat->pad >= CSI_NUM_PADS)
> @@ -1264,37 +1287,42 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
>  		goto out;
>  	}
>
> -	csi_try_fmt(priv, sensor, cfg, sdformat, &crop, &cc);
> +	crop = __csi_get_crop(priv, cfg, sdformat->which);
> +	compose = __csi_get_compose(priv, cfg, sdformat->which);
>
> -	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
> -		cfg->try_fmt = sdformat->format;
> -		goto out;
> -	}
> +	csi_try_fmt(priv, sensor, cfg, sdformat, crop, compose, &cc);
>
> -	priv->format_mbus[sdformat->pad] = sdformat->format;
> -	priv->cc[sdformat->pad] = cc;
> +	fmt = __csi_get_fmt(priv, cfg, sdformat->pad, sdformat->which);
> +	*fmt = sdformat->format;
>
>  	if (sdformat->pad == CSI_SINK_PAD) {
>  		int pad;
>
> -		/* reset the crop window */
> -		priv->crop = crop;
> -
>  		/* propagate format to source pads */
>  		for (pad = CSI_SINK_PAD + 1; pad < CSI_NUM_PADS; pad++) {
>  			const struct imx_media_pixfmt *outcc;
>  			struct v4l2_subdev_format format;
> +			struct v4l2_mbus_framefmt *outfmt;
>
>  			format.pad = pad;
> -			format.which = V4L2_SUBDEV_FORMAT_ACTIVE;
> +			format.which = sdformat->which;
>  			format.format = sdformat->format;
> -			csi_try_fmt(priv, sensor, cfg, &format, &crop, &outcc);
> +			csi_try_fmt(priv, sensor, cfg, &format, NULL, compose,
> +				    &outcc);
>
> -			priv->format_mbus[pad] = format.format;
> -			priv->cc[pad] = outcc;
> +			outfmt = __csi_get_fmt(priv, cfg, pad, sdformat->which);
> +			*outfmt = format.format;
> +
> +			if (sdformat->which == V4L2_SUBDEV_FORMAT_ACTIVE)
> +				priv->cc[pad] = outcc;
>  		}
>  	}
>
> +	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY)
> +		goto out;
> +
> +	priv->cc[sdformat->pad] = cc;
> +
>  	/* propagate IDMAC output pad format to capture device */
>  	imx_media_mbus_fmt_to_pix_fmt(&vdev_fmt,
>  				      &priv->format_mbus[CSI_SRC_PAD_IDMAC],
> @@ -1314,18 +1342,17 @@ static int csi_get_selection(struct v4l2_subdev *sd,
>  {
>  	struct csi_priv *priv = v4l2_get_subdevdata(sd);
>  	struct v4l2_mbus_framefmt *infmt;
> +	struct v4l2_rect *crop, *compose;
>  	int ret = 0;
>
> -	if (sel->pad >= CSI_NUM_PADS || sel->pad == CSI_SINK_PAD)
> +	if (sel->pad != CSI_SINK_PAD)
>  		return -EINVAL;
>
>  	mutex_lock(&priv->lock);
>
>  	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
> -	if (!infmt) {
> -		ret = -EINVAL;
> -		goto out;
> -	}
> +	crop = __csi_get_crop(priv, cfg, sel->which);
> +	compose = __csi_get_compose(priv, cfg, sel->which);
>
>  	switch (sel->target) {
>  	case V4L2_SEL_TGT_CROP_BOUNDS:
> @@ -1335,36 +1362,54 @@ static int csi_get_selection(struct v4l2_subdev *sd,
>  		sel->r.height = infmt->height;
>  		break;
>  	case V4L2_SEL_TGT_CROP:
> -		if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
> -			struct v4l2_rect *try_crop =
> -				v4l2_subdev_get_try_crop(&priv->sd,
> -							 cfg, sel->pad);
> -			sel->r = *try_crop;
> -		} else {
> -			sel->r = priv->crop;
> -		}
> +		sel->r = *crop;
> +		break;
> +	case V4L2_SEL_TGT_COMPOSE_BOUNDS:
> +		sel->r.left = 0;
> +		sel->r.top = 0;
> +		sel->r.width = crop->width;
> +		sel->r.height = crop->height;
> +		break;
> +	case V4L2_SEL_TGT_COMPOSE:
> +		sel->r = *compose;
>  		break;
>  	default:
>  		ret = -EINVAL;
>  	}
>
> -out:
>  	mutex_unlock(&priv->lock);
>  	return ret;
>  }
>
> +static int csi_set_scale(u32 *compose, u32 crop, u32 flags)
> +{
> +	if ((flags & (V4L2_SEL_FLAG_LE | V4L2_SEL_FLAG_GE)) ==
> +		     (V4L2_SEL_FLAG_LE | V4L2_SEL_FLAG_GE) &&
> +	    *compose != crop && *compose != crop / 2)
> +		return -ERANGE;
> +
> +	if (*compose <= crop / 2 ||
> +	    (*compose < crop * 3 / 4 && !(flags & V4L2_SEL_FLAG_GE)) ||
> +	    (*compose < crop && (flags & V4L2_SEL_FLAG_LE)))
> +		*compose = crop / 2;
> +	else
> +		*compose = crop;
> +
> +	return 0;
> +}
> +
>  static int csi_set_selection(struct v4l2_subdev *sd,
>  			     struct v4l2_subdev_pad_config *cfg,
>  			     struct v4l2_subdev_selection *sel)
>  {
>  	struct csi_priv *priv = v4l2_get_subdevdata(sd);
>  	struct v4l2_mbus_framefmt *infmt;
> +	struct v4l2_rect *crop, *compose;
>  	struct imx_media_subdev *sensor;
> +	int pad;
>  	int ret = 0;
>
> -	if (sel->pad >= CSI_NUM_PADS ||
> -	    sel->pad == CSI_SINK_PAD ||
> -	    sel->target != V4L2_SEL_TGT_CROP)
> +	if (sel->pad != CSI_SINK_PAD)
>  		return -EINVAL;
>
>  	sensor = imx_media_find_sensor(priv->md, &priv->sd.entity);
> @@ -1380,31 +1425,68 @@ static int csi_set_selection(struct v4l2_subdev *sd,
>  		goto out;
>  	}
>
> -	/*
> -	 * Modifying the crop rectangle always changes the format on the source
> -	 * pad. If the KEEP_CONFIG flag is set, just return the current crop
> -	 * rectangle.
> -	 */
> -	if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
> -		sel->r = priv->crop;
> -		if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
> -			cfg->try_crop = sel->r;
> +	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
> +	crop = __csi_get_crop(priv, cfg, sel->which);
> +	compose = __csi_get_compose(priv, cfg, sel->which);
> +
> +	switch (sel->target) {
> +	case V4L2_SEL_TGT_CROP:
> +		/*
> +		 * Modifying the crop rectangle always changes the format on
> +		 * the source pads. If the KEEP_CONFIG flag is set, just return
> +		 * the current crop rectangle.
> +		 */
> +		if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
> +			sel->r = priv->crop;
> +			if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
> +				*crop = sel->r;
> +			goto out;
> +		}
> +
> +		csi_try_crop(priv, &sel->r, cfg, infmt, sensor);
> +
> +		*crop = sel->r;
> +
> +		/* Reset scaling to 1:1 */
> +		compose->width = crop->width;
> +		compose->height = crop->height;
> +		break;
> +	case V4L2_SEL_TGT_COMPOSE:
> +		/*
> +		 * Modifying the compose rectangle always changes the format on
> +		 * the source pads. If the KEEP_CONFIG flag is set, just return
> +		 * the current compose rectangle.
> +		 */
> +		if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
> +			sel->r = priv->compose;
> +			if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
> +				*compose = sel->r;
> +			goto out;
> +		}
> +
> +		sel->r.left = 0;
> +		sel->r.top = 0;
> +		ret = csi_set_scale(&sel->r.width, crop->width, sel->flags);
> +		if (ret)
> +			goto out;
> +		ret = csi_set_scale(&sel->r.height, crop->height, sel->flags);
> +		if (ret)
> +			goto out;
> +
> +		*compose = sel->r;
> +		break;
> +	default:
> +		ret = -EINVAL;
>  		goto out;
>  	}
>
> -	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
> -	csi_try_crop(priv, &sel->r, cfg, infmt, sensor);
> -
> -	if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
> -		cfg->try_crop = sel->r;
> -	} else {
> -		struct v4l2_mbus_framefmt *outfmt =
> -			&priv->format_mbus[sel->pad];
> +	/* Reset source pads to sink compose rectangle */
> +	for (pad = CSI_SINK_PAD + 1; pad < CSI_NUM_PADS; pad++) {
> +		struct v4l2_mbus_framefmt *outfmt;
>
> -		priv->crop = sel->r;
> -		/* Update the source format */
> -		outfmt->width = sel->r.width;
> -		outfmt->height = sel->r.height;
> +		outfmt = __csi_get_fmt(priv, cfg, pad, sel->which);
> +		outfmt->width = compose->width;
> +		outfmt->height = compose->height;
>  	}
>
>  out:
> @@ -1467,6 +1549,12 @@ static int csi_registered(struct v4l2_subdev *sd)
>  			priv->skip[i - 1] = &csi_skip[0];
>  	}
>
> +	/* init default crop and compose rectangle sizes */
> +	priv->crop.width = 640;
> +	priv->crop.height = 480;
> +	priv->compose.width = 640;
> +	priv->compose.height = 480;
> +
>  	/* init default frame interval */
>  	priv->frame_interval.numerator = 1;
>  	priv->frame_interval.denominator = 30;
>

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Steve Longerbeam]

On 03/20/2017 10:23 AM, Philipp Zabel wrote:
> Hi Steve, Russell,
>
> On Mon, 2017-03-20 at 14:17 +0000, Russell King - ARM Linux wrote:
>> On Mon, Mar 20, 2017 at 03:00:51PM +0100, Philipp Zabel wrote:
>>> On Mon, 2017-03-20 at 12:08 +0000, Russell King - ARM Linux wrote:
>>>> The same document says:
>>>>
>>>>   Scaling support is optional. When supported by a subdev, the crop
>>>>   rectangle on the subdev's sink pad is scaled to the size configured
>>>>   using the
>>>>   :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
>>>>   using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
>>>>   subdev supports scaling but not composing, the top and left values are
>>>>   not used and must always be set to zero.
>>>
>>> Right, this sentence does imply that when scaling is supported, there
>>> must be a sink compose rectangle, even when composing is not.
>>>
>>> I have previously set up scaling like this:
>>>
>>> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
>>> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
>>>
>>> Does this mean, it should work like this instead?
>>>
>>> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
>>> media-ctl --set-v4l2 "'ipu1_csi0':0[fmt:UYVY2X8/1920x1080@1/60,compose:(0,0)/960x540]"
>>> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
>>>
>>> I suppose setting the source pad format should not be allowed to modify
>>> the sink compose rectangle.
>>
>> That is what I believe having read these documents several times, but
>> we need v4l2 people to confirm.
>
> What do you think of this:
>
> ----------8<----------
> From 2830aebc404bdfc9d7fc1ec94e5282d0b668e8f6 Mon Sep 17 00:00:00 2001
> From: Philipp Zabel <p.zabel@pengutronix.de>
> Date: Mon, 20 Mar 2017 17:10:21 +0100
> Subject: [PATCH] media: imx: csi: add sink selection rectangles
>
> Move the crop rectangle to the sink pad and add a sink compose rectangle
> to configure scaling. Also propagate rectangles from sink pad to crop
> rectangle, to compose rectangle, and to the source pads both in ACTIVE
> and TRY variants of set_fmt/selection, and initialize the default crop
> and compose rectangles.
>

I haven't had a chance to look at this patch in detail yet, but on
first glance it looks good to me. I'll try to find the time tomorrow
to incorporate it and then fixup Russell's subsequent patches for
the enum frame sizes/intervals.

Steve

> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
> ---
>  drivers/staging/media/imx/imx-media-csi.c | 216 +++++++++++++++++++++---------
>  1 file changed, 152 insertions(+), 64 deletions(-)
>
> diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
> index 560da3abdd70b..b026a5d602ddf 100644
> --- a/drivers/staging/media/imx/imx-media-csi.c
> +++ b/drivers/staging/media/imx/imx-media-csi.c
> @@ -79,6 +79,7 @@ struct csi_priv {
>  	const struct imx_media_pixfmt *cc[CSI_NUM_PADS];
>  	struct v4l2_fract frame_interval;
>  	struct v4l2_rect crop;
> +	struct v4l2_rect compose;
>  	const struct csi_skip_desc *skip[CSI_NUM_PADS - 1];
>
>  	/* active vb2 buffers to send to video dev sink */
> @@ -574,8 +575,8 @@ static int csi_setup(struct csi_priv *priv)
>  	ipu_csi_set_window(priv->csi, &priv->crop);
>
>  	ipu_csi_set_downsize(priv->csi,
> -			     priv->crop.width == 2 * outfmt->width,
> -			     priv->crop.height == 2 * outfmt->height);
> +			     priv->crop.width == 2 * priv->compose.width,
> +			     priv->crop.height == 2 * priv->compose.height);
>
>  	ipu_csi_init_interface(priv->csi, &sensor_mbus_cfg, &if_fmt);
>
> @@ -1001,6 +1002,27 @@ __csi_get_fmt(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
>  		return &priv->format_mbus[pad];
>  }
>
> +static struct v4l2_rect *
> +__csi_get_crop(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
> +	       enum v4l2_subdev_format_whence which)
> +{
> +	if (which == V4L2_SUBDEV_FORMAT_TRY)
> +		return v4l2_subdev_get_try_crop(&priv->sd, cfg, CSI_SINK_PAD);
> +	else
> +		return &priv->crop;
> +}
> +
> +static struct v4l2_rect *
> +__csi_get_compose(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
> +		  enum v4l2_subdev_format_whence which)
> +{
> +	if (which == V4L2_SUBDEV_FORMAT_TRY)
> +		return v4l2_subdev_get_try_compose(&priv->sd, cfg,
> +						   CSI_SINK_PAD);
> +	else
> +		return &priv->compose;
> +}
> +
>  static void csi_try_crop(struct csi_priv *priv,
>  			 struct v4l2_rect *crop,
>  			 struct v4l2_subdev_pad_config *cfg,
> @@ -1159,6 +1181,7 @@ static void csi_try_fmt(struct csi_priv *priv,
>  			struct v4l2_subdev_pad_config *cfg,
>  			struct v4l2_subdev_format *sdformat,
>  			struct v4l2_rect *crop,
> +			struct v4l2_rect *compose,
>  			const struct imx_media_pixfmt **cc)
>  {
>  	const struct imx_media_pixfmt *incc;
> @@ -1173,15 +1196,8 @@ static void csi_try_fmt(struct csi_priv *priv,
>  		incc = imx_media_find_mbus_format(infmt->code,
>  						  CS_SEL_ANY, true);
>
> -		if (sdformat->format.width < priv->crop.width * 3 / 4)
> -			sdformat->format.width = priv->crop.width / 2;
> -		else
> -			sdformat->format.width = priv->crop.width;
> -
> -		if (sdformat->format.height < priv->crop.height * 3 / 4)
> -			sdformat->format.height = priv->crop.height / 2;
> -		else
> -			sdformat->format.height = priv->crop.height;
> +		sdformat->format.width = compose->width;
> +		sdformat->format.height = compose->height;
>
>  		if (incc->bayer) {
>  			sdformat->format.code = infmt->code;
> @@ -1217,11 +1233,17 @@ static void csi_try_fmt(struct csi_priv *priv,
>  		v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
>  				      W_ALIGN, &sdformat->format.height,
>  				      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
> +
> +		/* Reset crop and compose rectangles */
>  		crop->left = 0;
>  		crop->top = 0;
>  		crop->width = sdformat->format.width;
>  		crop->height = sdformat->format.height;
>  		csi_try_crop(priv, crop, cfg, &sdformat->format, sensor);
> +		compose->left = 0;
> +		compose->top = 0;
> +		compose->width = crop->width;
> +		compose->height = crop->height;
>
>  		*cc = imx_media_find_mbus_format(sdformat->format.code,
>  						 CS_SEL_ANY, true);
> @@ -1245,7 +1267,8 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
>  	const struct imx_media_pixfmt *cc;
>  	struct imx_media_subdev *sensor;
>  	struct v4l2_pix_format vdev_fmt;
> -	struct v4l2_rect crop;
> +	struct v4l2_mbus_framefmt *fmt;
> +	struct v4l2_rect *crop, *compose;
>  	int ret = 0;
>
>  	if (sdformat->pad >= CSI_NUM_PADS)
> @@ -1264,37 +1287,42 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
>  		goto out;
>  	}
>
> -	csi_try_fmt(priv, sensor, cfg, sdformat, &crop, &cc);
> +	crop = __csi_get_crop(priv, cfg, sdformat->which);
> +	compose = __csi_get_compose(priv, cfg, sdformat->which);
>
> -	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
> -		cfg->try_fmt = sdformat->format;
> -		goto out;
> -	}
> +	csi_try_fmt(priv, sensor, cfg, sdformat, crop, compose, &cc);
>
> -	priv->format_mbus[sdformat->pad] = sdformat->format;
> -	priv->cc[sdformat->pad] = cc;
> +	fmt = __csi_get_fmt(priv, cfg, sdformat->pad, sdformat->which);
> +	*fmt = sdformat->format;
>
>  	if (sdformat->pad == CSI_SINK_PAD) {
>  		int pad;
>
> -		/* reset the crop window */
> -		priv->crop = crop;
> -
>  		/* propagate format to source pads */
>  		for (pad = CSI_SINK_PAD + 1; pad < CSI_NUM_PADS; pad++) {
>  			const struct imx_media_pixfmt *outcc;
>  			struct v4l2_subdev_format format;
> +			struct v4l2_mbus_framefmt *outfmt;
>
>  			format.pad = pad;
> -			format.which = V4L2_SUBDEV_FORMAT_ACTIVE;
> +			format.which = sdformat->which;
>  			format.format = sdformat->format;
> -			csi_try_fmt(priv, sensor, cfg, &format, &crop, &outcc);
> +			csi_try_fmt(priv, sensor, cfg, &format, NULL, compose,
> +				    &outcc);
>
> -			priv->format_mbus[pad] = format.format;
> -			priv->cc[pad] = outcc;
> +			outfmt = __csi_get_fmt(priv, cfg, pad, sdformat->which);
> +			*outfmt = format.format;
> +
> +			if (sdformat->which == V4L2_SUBDEV_FORMAT_ACTIVE)
> +				priv->cc[pad] = outcc;
>  		}
>  	}
>
> +	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY)
> +		goto out;
> +
> +	priv->cc[sdformat->pad] = cc;
> +
>  	/* propagate IDMAC output pad format to capture device */
>  	imx_media_mbus_fmt_to_pix_fmt(&vdev_fmt,
>  				      &priv->format_mbus[CSI_SRC_PAD_IDMAC],
> @@ -1314,18 +1342,17 @@ static int csi_get_selection(struct v4l2_subdev *sd,
>  {
>  	struct csi_priv *priv = v4l2_get_subdevdata(sd);
>  	struct v4l2_mbus_framefmt *infmt;
> +	struct v4l2_rect *crop, *compose;
>  	int ret = 0;
>
> -	if (sel->pad >= CSI_NUM_PADS || sel->pad == CSI_SINK_PAD)
> +	if (sel->pad != CSI_SINK_PAD)
>  		return -EINVAL;
>
>  	mutex_lock(&priv->lock);
>
>  	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
> -	if (!infmt) {
> -		ret = -EINVAL;
> -		goto out;
> -	}
> +	crop = __csi_get_crop(priv, cfg, sel->which);
> +	compose = __csi_get_compose(priv, cfg, sel->which);
>
>  	switch (sel->target) {
>  	case V4L2_SEL_TGT_CROP_BOUNDS:
> @@ -1335,36 +1362,54 @@ static int csi_get_selection(struct v4l2_subdev *sd,
>  		sel->r.height = infmt->height;
>  		break;
>  	case V4L2_SEL_TGT_CROP:
> -		if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
> -			struct v4l2_rect *try_crop =
> -				v4l2_subdev_get_try_crop(&priv->sd,
> -							 cfg, sel->pad);
> -			sel->r = *try_crop;
> -		} else {
> -			sel->r = priv->crop;
> -		}
> +		sel->r = *crop;
> +		break;
> +	case V4L2_SEL_TGT_COMPOSE_BOUNDS:
> +		sel->r.left = 0;
> +		sel->r.top = 0;
> +		sel->r.width = crop->width;
> +		sel->r.height = crop->height;
> +		break;
> +	case V4L2_SEL_TGT_COMPOSE:
> +		sel->r = *compose;
>  		break;
>  	default:
>  		ret = -EINVAL;
>  	}
>
> -out:
>  	mutex_unlock(&priv->lock);
>  	return ret;
>  }
>
> +static int csi_set_scale(u32 *compose, u32 crop, u32 flags)
> +{
> +	if ((flags & (V4L2_SEL_FLAG_LE | V4L2_SEL_FLAG_GE)) ==
> +		     (V4L2_SEL_FLAG_LE | V4L2_SEL_FLAG_GE) &&
> +	    *compose != crop && *compose != crop / 2)
> +		return -ERANGE;
> +
> +	if (*compose <= crop / 2 ||
> +	    (*compose < crop * 3 / 4 && !(flags & V4L2_SEL_FLAG_GE)) ||
> +	    (*compose < crop && (flags & V4L2_SEL_FLAG_LE)))
> +		*compose = crop / 2;
> +	else
> +		*compose = crop;
> +
> +	return 0;
> +}
> +
>  static int csi_set_selection(struct v4l2_subdev *sd,
>  			     struct v4l2_subdev_pad_config *cfg,
>  			     struct v4l2_subdev_selection *sel)
>  {
>  	struct csi_priv *priv = v4l2_get_subdevdata(sd);
>  	struct v4l2_mbus_framefmt *infmt;
> +	struct v4l2_rect *crop, *compose;
>  	struct imx_media_subdev *sensor;
> +	int pad;
>  	int ret = 0;
>
> -	if (sel->pad >= CSI_NUM_PADS ||
> -	    sel->pad == CSI_SINK_PAD ||
> -	    sel->target != V4L2_SEL_TGT_CROP)
> +	if (sel->pad != CSI_SINK_PAD)
>  		return -EINVAL;
>
>  	sensor = imx_media_find_sensor(priv->md, &priv->sd.entity);
> @@ -1380,31 +1425,68 @@ static int csi_set_selection(struct v4l2_subdev *sd,
>  		goto out;
>  	}
>
> -	/*
> -	 * Modifying the crop rectangle always changes the format on the source
> -	 * pad. If the KEEP_CONFIG flag is set, just return the current crop
> -	 * rectangle.
> -	 */
> -	if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
> -		sel->r = priv->crop;
> -		if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
> -			cfg->try_crop = sel->r;
> +	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
> +	crop = __csi_get_crop(priv, cfg, sel->which);
> +	compose = __csi_get_compose(priv, cfg, sel->which);
> +
> +	switch (sel->target) {
> +	case V4L2_SEL_TGT_CROP:
> +		/*
> +		 * Modifying the crop rectangle always changes the format on
> +		 * the source pads. If the KEEP_CONFIG flag is set, just return
> +		 * the current crop rectangle.
> +		 */
> +		if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
> +			sel->r = priv->crop;
> +			if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
> +				*crop = sel->r;
> +			goto out;
> +		}
> +
> +		csi_try_crop(priv, &sel->r, cfg, infmt, sensor);
> +
> +		*crop = sel->r;
> +
> +		/* Reset scaling to 1:1 */
> +		compose->width = crop->width;
> +		compose->height = crop->height;
> +		break;
> +	case V4L2_SEL_TGT_COMPOSE:
> +		/*
> +		 * Modifying the compose rectangle always changes the format on
> +		 * the source pads. If the KEEP_CONFIG flag is set, just return
> +		 * the current compose rectangle.
> +		 */
> +		if (sel->flags & V4L2_SEL_FLAG_KEEP_CONFIG) {
> +			sel->r = priv->compose;
> +			if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
> +				*compose = sel->r;
> +			goto out;
> +		}
> +
> +		sel->r.left = 0;
> +		sel->r.top = 0;
> +		ret = csi_set_scale(&sel->r.width, crop->width, sel->flags);
> +		if (ret)
> +			goto out;
> +		ret = csi_set_scale(&sel->r.height, crop->height, sel->flags);
> +		if (ret)
> +			goto out;
> +
> +		*compose = sel->r;
> +		break;
> +	default:
> +		ret = -EINVAL;
>  		goto out;
>  	}
>
> -	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
> -	csi_try_crop(priv, &sel->r, cfg, infmt, sensor);
> -
> -	if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
> -		cfg->try_crop = sel->r;
> -	} else {
> -		struct v4l2_mbus_framefmt *outfmt =
> -			&priv->format_mbus[sel->pad];
> +	/* Reset source pads to sink compose rectangle */
> +	for (pad = CSI_SINK_PAD + 1; pad < CSI_NUM_PADS; pad++) {
> +		struct v4l2_mbus_framefmt *outfmt;
>
> -		priv->crop = sel->r;
> -		/* Update the source format */
> -		outfmt->width = sel->r.width;
> -		outfmt->height = sel->r.height;
> +		outfmt = __csi_get_fmt(priv, cfg, pad, sel->which);
> +		outfmt->width = compose->width;
> +		outfmt->height = compose->height;
>  	}
>
>  out:
> @@ -1467,6 +1549,12 @@ static int csi_registered(struct v4l2_subdev *sd)
>  			priv->skip[i - 1] = &csi_skip[0];
>  	}
>
> +	/* init default crop and compose rectangle sizes */
> +	priv->crop.width = 640;
> +	priv->crop.height = 480;
> +	priv->compose.width = 640;
> +	priv->compose.height = 480;
> +
>  	/* init default frame interval */
>  	priv->frame_interval.numerator = 1;
>  	priv->frame_interval.denominator = 30;
>

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 06:23:24PM +0100, Philipp Zabel wrote:
> @@ -1173,15 +1196,8 @@ static void csi_try_fmt(struct csi_priv *priv,
>  		incc = imx_media_find_mbus_format(infmt->code,
>  						  CS_SEL_ANY, true);
>  
> -		if (sdformat->format.width < priv->crop.width * 3 / 4)
> -			sdformat->format.width = priv->crop.width / 2;
> -		else
> -			sdformat->format.width = priv->crop.width;
> -
> -		if (sdformat->format.height < priv->crop.height * 3 / 4)
> -			sdformat->format.height = priv->crop.height / 2;
> -		else
> -			sdformat->format.height = priv->crop.height;
> +		sdformat->format.width = compose->width;
> +		sdformat->format.height = compose->height;
>  
>  		if (incc->bayer) {
>  			sdformat->format.code = infmt->code;

We need to do more in here, because right now setting the source pads
overwrites the colorimetry etc information.  Maybe something like the
below?  I'm wondering if it would be a saner approach to copy the
sink format and update the parameters that can be changed, rather than
trying to list all the parameters that shouldn't be changed.  What if
the format structure gains a new member?

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index 1492b92e1970..756204ced53c 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -1221,6 +1221,12 @@ static void csi_try_fmt(struct csi_priv *priv,
 			sdformat->format.field =  (infmt->height == 480) ?
 				V4L2_FIELD_SEQ_TB : V4L2_FIELD_SEQ_BT;
 		}
+
+		/* copy settings we can't change */
+		sdformat->format.colorspace = infmt->colorspace;
+		sdformat->format.ycbcr_enc = infmt->ycbcr_enc;
+		sdformat->format.quantization = infmt->quantization;
+		sdformat->format.xfer_func = infmt->xfer_func;
 		break;
 	case CSI_SINK_PAD:
 		v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,



-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 06:23:24PM +0100, Philipp Zabel wrote:
> @@ -1173,15 +1196,8 @@ static void csi_try_fmt(struct csi_priv *priv,
>  		incc = imx_media_find_mbus_format(infmt->code,
>  						  CS_SEL_ANY, true);
>  
> -		if (sdformat->format.width < priv->crop.width * 3 / 4)
> -			sdformat->format.width = priv->crop.width / 2;
> -		else
> -			sdformat->format.width = priv->crop.width;
> -
> -		if (sdformat->format.height < priv->crop.height * 3 / 4)
> -			sdformat->format.height = priv->crop.height / 2;
> -		else
> -			sdformat->format.height = priv->crop.height;
> +		sdformat->format.width = compose->width;
> +		sdformat->format.height = compose->height;
>  
>  		if (incc->bayer) {
>  			sdformat->format.code = infmt->code;

We need to do more in here, because right now setting the source pads
overwrites the colorimetry etc information.  Maybe something like the
below?  I'm wondering if it would be a saner approach to copy the
sink format and update the parameters that can be changed, rather than
trying to list all the parameters that shouldn't be changed.  What if
the format structure gains a new member?

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index 1492b92e1970..756204ced53c 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -1221,6 +1221,12 @@ static void csi_try_fmt(struct csi_priv *priv,
 			sdformat->format.field =  (infmt->height == 480) ?
 				V4L2_FIELD_SEQ_TB : V4L2_FIELD_SEQ_BT;
 		}
+
+		/* copy settings we can't change */
+		sdformat->format.colorspace = infmt->colorspace;
+		sdformat->format.ycbcr_enc = infmt->ycbcr_enc;
+		sdformat->format.quantization = infmt->quantization;
+		sdformat->format.xfer_func = infmt->xfer_func;
 		break;
 	case CSI_SINK_PAD:
 		v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,



-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 06:23:24PM +0100, Philipp Zabel wrote:
> @@ -1173,15 +1196,8 @@ static void csi_try_fmt(struct csi_priv *priv,
>  		incc = imx_media_find_mbus_format(infmt->code,
>  						  CS_SEL_ANY, true);
>  
> -		if (sdformat->format.width < priv->crop.width * 3 / 4)
> -			sdformat->format.width = priv->crop.width / 2;
> -		else
> -			sdformat->format.width = priv->crop.width;
> -
> -		if (sdformat->format.height < priv->crop.height * 3 / 4)
> -			sdformat->format.height = priv->crop.height / 2;
> -		else
> -			sdformat->format.height = priv->crop.height;
> +		sdformat->format.width = compose->width;
> +		sdformat->format.height = compose->height;
>  
>  		if (incc->bayer) {
>  			sdformat->format.code = infmt->code;

We need to do more in here, because right now setting the source pads
overwrites the colorimetry etc information.  Maybe something like the
below?  I'm wondering if it would be a saner approach to copy the
sink format and update the parameters that can be changed, rather than
trying to list all the parameters that shouldn't be changed.  What if
the format structure gains a new member?

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index 1492b92e1970..756204ced53c 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -1221,6 +1221,12 @@ static void csi_try_fmt(struct csi_priv *priv,
 			sdformat->format.field =  (infmt->height == 480) ?
 				V4L2_FIELD_SEQ_TB : V4L2_FIELD_SEQ_BT;
 		}
+
+		/* copy settings we can't change */
+		sdformat->format.colorspace = infmt->colorspace;
+		sdformat->format.ycbcr_enc = infmt->ycbcr_enc;
+		sdformat->format.quantization = infmt->quantization;
+		sdformat->format.xfer_func = infmt->xfer_func;
 		break;
 	case CSI_SINK_PAD:
 		v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,



-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Steve Longerbeam]

On 03/21/2017 04:27 AM, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 06:23:24PM +0100, Philipp Zabel wrote:
>> @@ -1173,15 +1196,8 @@ static void csi_try_fmt(struct csi_priv *priv,
>>  		incc = imx_media_find_mbus_format(infmt->code,
>>  						  CS_SEL_ANY, true);
>>
>> -		if (sdformat->format.width < priv->crop.width * 3 / 4)
>> -			sdformat->format.width = priv->crop.width / 2;
>> -		else
>> -			sdformat->format.width = priv->crop.width;
>> -
>> -		if (sdformat->format.height < priv->crop.height * 3 / 4)
>> -			sdformat->format.height = priv->crop.height / 2;
>> -		else
>> -			sdformat->format.height = priv->crop.height;
>> +		sdformat->format.width = compose->width;
>> +		sdformat->format.height = compose->height;
>>
>>  		if (incc->bayer) {
>>  			sdformat->format.code = infmt->code;
>
> We need to do more in here, because right now setting the source pads
> overwrites the colorimetry etc information.  Maybe something like the
> below?

I'm thinking, to support propagating the colorimetry params, there
should be a util function

void imx_media_copy_colorimetry(struct v4l2_mbus_framefmt *out,
				struct v4l2_mbus_framefmt *in);

that can be used throughout the pipeline, that does exactly what
you add below.

>  I'm wondering if it would be a saner approach to copy the
> sink format and update the parameters that can be changed, rather than
> trying to list all the parameters that shouldn't be changed.

For CSI that is a bit difficult, because the source formats are
hardly related to the sink formats, so so much would have to be
modified after copying the sink format that it would be rather
pointless, except to forward the colorimetry params.

Steve

>  What if the format structure gains a new member?
>
> diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
> index 1492b92e1970..756204ced53c 100644
> --- a/drivers/staging/media/imx/imx-media-csi.c
> +++ b/drivers/staging/media/imx/imx-media-csi.c
> @@ -1221,6 +1221,12 @@ static void csi_try_fmt(struct csi_priv *priv,
>  			sdformat->format.field =  (infmt->height == 480) ?
>  				V4L2_FIELD_SEQ_TB : V4L2_FIELD_SEQ_BT;
>  		}
> +
> +		/* copy settings we can't change */
> +		sdformat->format.colorspace = infmt->colorspace;
> +		sdformat->format.ycbcr_enc = infmt->ycbcr_enc;
> +		sdformat->format.quantization = infmt->quantization;
> +		sdformat->format.xfer_func = infmt->xfer_func;
>  		break;
>  	case CSI_SINK_PAD:
>  		v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
>
>
>

[PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Steve Longerbeam]

On 03/21/2017 04:27 AM, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 06:23:24PM +0100, Philipp Zabel wrote:
>> @@ -1173,15 +1196,8 @@ static void csi_try_fmt(struct csi_priv *priv,
>>  		incc = imx_media_find_mbus_format(infmt->code,
>>  						  CS_SEL_ANY, true);
>>
>> -		if (sdformat->format.width < priv->crop.width * 3 / 4)
>> -			sdformat->format.width = priv->crop.width / 2;
>> -		else
>> -			sdformat->format.width = priv->crop.width;
>> -
>> -		if (sdformat->format.height < priv->crop.height * 3 / 4)
>> -			sdformat->format.height = priv->crop.height / 2;
>> -		else
>> -			sdformat->format.height = priv->crop.height;
>> +		sdformat->format.width = compose->width;
>> +		sdformat->format.height = compose->height;
>>
>>  		if (incc->bayer) {
>>  			sdformat->format.code = infmt->code;
>
> We need to do more in here, because right now setting the source pads
> overwrites the colorimetry etc information.  Maybe something like the
> below?

I'm thinking, to support propagating the colorimetry params, there
should be a util function

void imx_media_copy_colorimetry(struct v4l2_mbus_framefmt *out,
				struct v4l2_mbus_framefmt *in);

that can be used throughout the pipeline, that does exactly what
you add below.

>  I'm wondering if it would be a saner approach to copy the
> sink format and update the parameters that can be changed, rather than
> trying to list all the parameters that shouldn't be changed.

For CSI that is a bit difficult, because the source formats are
hardly related to the sink formats, so so much would have to be
modified after copying the sink format that it would be rather
pointless, except to forward the colorimetry params.

Steve

>  What if the format structure gains a new member?
>
> diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
> index 1492b92e1970..756204ced53c 100644
> --- a/drivers/staging/media/imx/imx-media-csi.c
> +++ b/drivers/staging/media/imx/imx-media-csi.c
> @@ -1221,6 +1221,12 @@ static void csi_try_fmt(struct csi_priv *priv,
>  			sdformat->format.field =  (infmt->height == 480) ?
>  				V4L2_FIELD_SEQ_TB : V4L2_FIELD_SEQ_BT;
>  		}
> +
> +		/* copy settings we can't change */
> +		sdformat->format.colorspace = infmt->colorspace;
> +		sdformat->format.ycbcr_enc = infmt->ycbcr_enc;
> +		sdformat->format.quantization = infmt->quantization;
> +		sdformat->format.xfer_func = infmt->xfer_func;
>  		break;
>  	case CSI_SINK_PAD:
>  		v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
>
>
>

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Steve Longerbeam]

On 03/21/2017 04:27 AM, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 06:23:24PM +0100, Philipp Zabel wrote:
>> @@ -1173,15 +1196,8 @@ static void csi_try_fmt(struct csi_priv *priv,
>>  		incc = imx_media_find_mbus_format(infmt->code,
>>  						  CS_SEL_ANY, true);
>>
>> -		if (sdformat->format.width < priv->crop.width * 3 / 4)
>> -			sdformat->format.width = priv->crop.width / 2;
>> -		else
>> -			sdformat->format.width = priv->crop.width;
>> -
>> -		if (sdformat->format.height < priv->crop.height * 3 / 4)
>> -			sdformat->format.height = priv->crop.height / 2;
>> -		else
>> -			sdformat->format.height = priv->crop.height;
>> +		sdformat->format.width = compose->width;
>> +		sdformat->format.height = compose->height;
>>
>>  		if (incc->bayer) {
>>  			sdformat->format.code = infmt->code;
>
> We need to do more in here, because right now setting the source pads
> overwrites the colorimetry etc information.  Maybe something like the
> below?

I'm thinking, to support propagating the colorimetry params, there
should be a util function

void imx_media_copy_colorimetry(struct v4l2_mbus_framefmt *out,
				struct v4l2_mbus_framefmt *in);

that can be used throughout the pipeline, that does exactly what
you add below.

>  I'm wondering if it would be a saner approach to copy the
> sink format and update the parameters that can be changed, rather than
> trying to list all the parameters that shouldn't be changed.

For CSI that is a bit difficult, because the source formats are
hardly related to the sink formats, so so much would have to be
modified after copying the sink format that it would be rather
pointless, except to forward the colorimetry params.

Steve

>  What if the format structure gains a new member?
>
> diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
> index 1492b92e1970..756204ced53c 100644
> --- a/drivers/staging/media/imx/imx-media-csi.c
> +++ b/drivers/staging/media/imx/imx-media-csi.c
> @@ -1221,6 +1221,12 @@ static void csi_try_fmt(struct csi_priv *priv,
>  			sdformat->format.field =  (infmt->height == 480) ?
>  				V4L2_FIELD_SEQ_TB : V4L2_FIELD_SEQ_BT;
>  		}
> +
> +		/* copy settings we can't change */
> +		sdformat->format.colorspace = infmt->colorspace;
> +		sdformat->format.ycbcr_enc = infmt->ycbcr_enc;
> +		sdformat->format.quantization = infmt->quantization;
> +		sdformat->format.xfer_func = infmt->xfer_func;
>  		break;
>  	case CSI_SINK_PAD:
>  		v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
>
>
>

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Steve Longerbeam]

Hi Philipp, Russell,


On 03/20/2017 10:23 AM, Philipp Zabel wrote:
> Hi Steve, Russell,
>
> <snip>
>
> What do you think of this:
>
> ----------8<----------
> From 2830aebc404bdfc9d7fc1ec94e5282d0b668e8f6 Mon Sep 17 00:00:00 2001
> From: Philipp Zabel <p.zabel@pengutronix.de>
> Date: Mon, 20 Mar 2017 17:10:21 +0100
> Subject: [PATCH] media: imx: csi: add sink selection rectangles
>
> Move the crop rectangle to the sink pad and add a sink compose rectangle
> to configure scaling. Also propagate rectangles from sink pad to crop
> rectangle, to compose rectangle, and to the source pads both in ACTIVE
> and TRY variants of set_fmt/selection, and initialize the default crop
> and compose rectangles.
>


I applied this patch.

I noticed Philipp fixed a bug in the sink->source pad format
propagation. I was only propagating the active runs, and not
the trial runs. I fixed this everywhere in the pipeline, applied
to the "propagate sink pad formats to source pads" patch. Try
runs should now work correctly across the whole pipeline, but
I haven't tested this.

Steve

[PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Steve Longerbeam]

Hi Philipp, Russell,


On 03/20/2017 10:23 AM, Philipp Zabel wrote:
> Hi Steve, Russell,
>
> <snip>
>
> What do you think of this:
>
> ----------8<----------
> From 2830aebc404bdfc9d7fc1ec94e5282d0b668e8f6 Mon Sep 17 00:00:00 2001
> From: Philipp Zabel <p.zabel@pengutronix.de>
> Date: Mon, 20 Mar 2017 17:10:21 +0100
> Subject: [PATCH] media: imx: csi: add sink selection rectangles
>
> Move the crop rectangle to the sink pad and add a sink compose rectangle
> to configure scaling. Also propagate rectangles from sink pad to crop
> rectangle, to compose rectangle, and to the source pads both in ACTIVE
> and TRY variants of set_fmt/selection, and initialize the default crop
> and compose rectangles.
>


I applied this patch.

I noticed Philipp fixed a bug in the sink->source pad format
propagation. I was only propagating the active runs, and not
the trial runs. I fixed this everywhere in the pipeline, applied
to the "propagate sink pad formats to source pads" patch. Try
runs should now work correctly across the whole pipeline, but
I haven't tested this.

Steve

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Steve Longerbeam]

Hi Philipp, Russell,


On 03/20/2017 10:23 AM, Philipp Zabel wrote:
> Hi Steve, Russell,
>
> <snip>
>
> What do you think of this:
>
> ----------8<----------
> From 2830aebc404bdfc9d7fc1ec94e5282d0b668e8f6 Mon Sep 17 00:00:00 2001
> From: Philipp Zabel <p.zabel@pengutronix.de>
> Date: Mon, 20 Mar 2017 17:10:21 +0100
> Subject: [PATCH] media: imx: csi: add sink selection rectangles
>
> Move the crop rectangle to the sink pad and add a sink compose rectangle
> to configure scaling. Also propagate rectangles from sink pad to crop
> rectangle, to compose rectangle, and to the source pads both in ACTIVE
> and TRY variants of set_fmt/selection, and initialize the default crop
> and compose rectangles.
>


I applied this patch.

I noticed Philipp fixed a bug in the sink->source pad format
propagation. I was only propagating the active runs, and not
the trial runs. I fixed this everywhere in the pipeline, applied
to the "propagate sink pad formats to source pads" patch. Try
runs should now work correctly across the whole pipeline, but
I haven't tested this.

Steve

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Philipp Zabel]

On Mon, 2017-03-20 at 14:17 +0000, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 03:00:51PM +0100, Philipp Zabel wrote:
> > On Mon, 2017-03-20 at 12:08 +0000, Russell King - ARM Linux wrote:
> > > The same document says:
> > > 
> > >   Scaling support is optional. When supported by a subdev, the crop
> > >   rectangle on the subdev's sink pad is scaled to the size configured
> > >   using the
> > >   :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
> > >   using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
> > >   subdev supports scaling but not composing, the top and left values are
> > >   not used and must always be set to zero.
> > 
> > Right, this sentence does imply that when scaling is supported, there
> > must be a sink compose rectangle, even when composing is not.
> > 
> > I have previously set up scaling like this:
> > 
> > media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> > media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
> > 
> > Does this mean, it should work like this instead?
> > 
> > media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> > media-ctl --set-v4l2 "'ipu1_csi0':0[fmt:UYVY2X8/1920x1080@1/60,compose:(0,0)/960x540]"
> > media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
> > 
> > I suppose setting the source pad format should not be allowed to modify
> > the sink compose rectangle.
> 
> That is what I believe having read these documents several times, but
> we need v4l2 people to confirm.
> 
> Note that setting the format on 'ipu1_csi0':0 should already be done by
> the previous media-ctl command, so it should be possible to simplify
> that to:
> 
> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> media-ctl --set-v4l2 "'ipu1_csi0':0[compose:(0,0)/960x540]"
> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"

Thanks, that works, too.

> I have tripped over a bug in media-ctl when specifying both a crop and
> compose rectangle - the --help output suggests that "," should be used
> to separate them.  media-ctl rejects that, telling me the character at
> the "," should be "]".  Replacing the "," with " " allows media-ctl to
> accept it and set both rectangles, so it sounds like a parser bug - I've
> not looked into this any further yet.

I can confirm this. I don't see any place in
v4l2_subdev_parse_pad_format that handles the "," separator. There's
just whitespace skipping between the v4l2-properties.

regards
Philipp

[PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Philipp Zabel]

On Mon, 2017-03-20 at 14:17 +0000, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 03:00:51PM +0100, Philipp Zabel wrote:
> > On Mon, 2017-03-20 at 12:08 +0000, Russell King - ARM Linux wrote:
> > > The same document says:
> > > 
> > >   Scaling support is optional. When supported by a subdev, the crop
> > >   rectangle on the subdev's sink pad is scaled to the size configured
> > >   using the
> > >   :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
> > >   using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
> > >   subdev supports scaling but not composing, the top and left values are
> > >   not used and must always be set to zero.
> > 
> > Right, this sentence does imply that when scaling is supported, there
> > must be a sink compose rectangle, even when composing is not.
> > 
> > I have previously set up scaling like this:
> > 
> > media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080 at 1/60]"
> > media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540 at 1/30]"
> > 
> > Does this mean, it should work like this instead?
> > 
> > media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080 at 1/60]"
> > media-ctl --set-v4l2 "'ipu1_csi0':0[fmt:UYVY2X8/1920x1080 at 1/60,compose:(0,0)/960x540]"
> > media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540 at 1/30]"
> > 
> > I suppose setting the source pad format should not be allowed to modify
> > the sink compose rectangle.
> 
> That is what I believe having read these documents several times, but
> we need v4l2 people to confirm.
> 
> Note that setting the format on 'ipu1_csi0':0 should already be done by
> the previous media-ctl command, so it should be possible to simplify
> that to:
> 
> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080 at 1/60]"
> media-ctl --set-v4l2 "'ipu1_csi0':0[compose:(0,0)/960x540]"
> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540 at 1/30]"

Thanks, that works, too.

> I have tripped over a bug in media-ctl when specifying both a crop and
> compose rectangle - the --help output suggests that "," should be used
> to separate them.  media-ctl rejects that, telling me the character at
> the "," should be "]".  Replacing the "," with " " allows media-ctl to
> accept it and set both rectangles, so it sounds like a parser bug - I've
> not looked into this any further yet.

I can confirm this. I don't see any place in
v4l2_subdev_parse_pad_format that handles the "," separator. There's
just whitespace skipping between the v4l2-properties.

regards
Philipp

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Philipp Zabel]

On Mon, 2017-03-20 at 14:17 +0000, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 03:00:51PM +0100, Philipp Zabel wrote:
> > On Mon, 2017-03-20 at 12:08 +0000, Russell King - ARM Linux wrote:
> > > The same document says:
> > > 
> > >   Scaling support is optional. When supported by a subdev, the crop
> > >   rectangle on the subdev's sink pad is scaled to the size configured
> > >   using the
> > >   :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
> > >   using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
> > >   subdev supports scaling but not composing, the top and left values are
> > >   not used and must always be set to zero.
> > 
> > Right, this sentence does imply that when scaling is supported, there
> > must be a sink compose rectangle, even when composing is not.
> > 
> > I have previously set up scaling like this:
> > 
> > media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> > media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
> > 
> > Does this mean, it should work like this instead?
> > 
> > media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> > media-ctl --set-v4l2 "'ipu1_csi0':0[fmt:UYVY2X8/1920x1080@1/60,compose:(0,0)/960x540]"
> > media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
> > 
> > I suppose setting the source pad format should not be allowed to modify
> > the sink compose rectangle.
> 
> That is what I believe having read these documents several times, but
> we need v4l2 people to confirm.
> 
> Note that setting the format on 'ipu1_csi0':0 should already be done by
> the previous media-ctl command, so it should be possible to simplify
> that to:
> 
> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> media-ctl --set-v4l2 "'ipu1_csi0':0[compose:(0,0)/960x540]"
> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"

Thanks, that works, too.

> I have tripped over a bug in media-ctl when specifying both a crop and
> compose rectangle - the --help output suggests that "," should be used
> to separate them.  media-ctl rejects that, telling me the character at
> the "," should be "]".  Replacing the "," with " " allows media-ctl to
> accept it and set both rectangles, so it sounds like a parser bug - I've
> not looked into this any further yet.

I can confirm this. I don't see any place in
v4l2_subdev_parse_pad_format that handles the "," separator. There's
just whitespace skipping between the v4l2-properties.

regards
Philipp

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 06:40:21PM +0100, Philipp Zabel wrote:
> On Mon, 2017-03-20 at 14:17 +0000, Russell King - ARM Linux wrote:
> > I have tripped over a bug in media-ctl when specifying both a crop and
> > compose rectangle - the --help output suggests that "," should be used
> > to separate them.  media-ctl rejects that, telling me the character at
> > the "," should be "]".  Replacing the "," with " " allows media-ctl to
> > accept it and set both rectangles, so it sounds like a parser bug - I've
> > not looked into this any further yet.
> 
> I can confirm this. I don't see any place in
> v4l2_subdev_parse_pad_format that handles the "," separator. There's
> just whitespace skipping between the v4l2-properties.

Maybe this is the easiest solution:

 utils/media-ctl/options.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/utils/media-ctl/options.c b/utils/media-ctl/options.c
index 83ca1ca..8b97874 100644
--- a/utils/media-ctl/options.c
+++ b/utils/media-ctl/options.c
@@ -65,7 +65,7 @@ static void usage(const char *argv0)
 	printf("\tentity          = entity-number | ( '\"' entity-name '\"' ) ;\n");
 	printf("\n");
 	printf("\tv4l2            = pad '[' v4l2-properties ']' ;\n");
-	printf("\tv4l2-properties = v4l2-property { ',' v4l2-property } ;\n");
+	printf("\tv4l2-properties = v4l2-property { ' '* v4l2-property } ;\n");
 	printf("\tv4l2-property   = v4l2-mbusfmt | v4l2-crop | v4l2-interval\n");
 	printf("\t                | v4l2-compose | v4l2-interval ;\n");
 	printf("\tv4l2-mbusfmt    = 'fmt:' fcc '/' size ; { 'field:' v4l2-field ; } { 'colorspace:' v4l2-colorspace ; }\n");

;)

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 06:40:21PM +0100, Philipp Zabel wrote:
> On Mon, 2017-03-20 at 14:17 +0000, Russell King - ARM Linux wrote:
> > I have tripped over a bug in media-ctl when specifying both a crop and
> > compose rectangle - the --help output suggests that "," should be used
> > to separate them.  media-ctl rejects that, telling me the character at
> > the "," should be "]".  Replacing the "," with " " allows media-ctl to
> > accept it and set both rectangles, so it sounds like a parser bug - I've
> > not looked into this any further yet.
> 
> I can confirm this. I don't see any place in
> v4l2_subdev_parse_pad_format that handles the "," separator. There's
> just whitespace skipping between the v4l2-properties.

Maybe this is the easiest solution:

 utils/media-ctl/options.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/utils/media-ctl/options.c b/utils/media-ctl/options.c
index 83ca1ca..8b97874 100644
--- a/utils/media-ctl/options.c
+++ b/utils/media-ctl/options.c
@@ -65,7 +65,7 @@ static void usage(const char *argv0)
 	printf("\tentity          = entity-number | ( '\"' entity-name '\"' ) ;\n");
 	printf("\n");
 	printf("\tv4l2            = pad '[' v4l2-properties ']' ;\n");
-	printf("\tv4l2-properties = v4l2-property { ',' v4l2-property } ;\n");
+	printf("\tv4l2-properties = v4l2-property { ' '* v4l2-property } ;\n");
 	printf("\tv4l2-property   = v4l2-mbusfmt | v4l2-crop | v4l2-interval\n");
 	printf("\t                | v4l2-compose | v4l2-interval ;\n");
 	printf("\tv4l2-mbusfmt    = 'fmt:' fcc '/' size ; { 'field:' v4l2-field ; } { 'colorspace:' v4l2-colorspace ; }\n");

;)

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 06:40:21PM +0100, Philipp Zabel wrote:
> On Mon, 2017-03-20 at 14:17 +0000, Russell King - ARM Linux wrote:
> > I have tripped over a bug in media-ctl when specifying both a crop and
> > compose rectangle - the --help output suggests that "," should be used
> > to separate them.  media-ctl rejects that, telling me the character at
> > the "," should be "]".  Replacing the "," with " " allows media-ctl to
> > accept it and set both rectangles, so it sounds like a parser bug - I've
> > not looked into this any further yet.
> 
> I can confirm this. I don't see any place in
> v4l2_subdev_parse_pad_format that handles the "," separator. There's
> just whitespace skipping between the v4l2-properties.

Maybe this is the easiest solution:

 utils/media-ctl/options.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/utils/media-ctl/options.c b/utils/media-ctl/options.c
index 83ca1ca..8b97874 100644
--- a/utils/media-ctl/options.c
+++ b/utils/media-ctl/options.c
@@ -65,7 +65,7 @@ static void usage(const char *argv0)
 	printf("\tentity          = entity-number | ( '\"' entity-name '\"' ) ;\n");
 	printf("\n");
 	printf("\tv4l2            = pad '[' v4l2-properties ']' ;\n");
-	printf("\tv4l2-properties = v4l2-property { ',' v4l2-property } ;\n");
+	printf("\tv4l2-properties = v4l2-property { ' '* v4l2-property } ;\n");
 	printf("\tv4l2-property   = v4l2-mbusfmt | v4l2-crop | v4l2-interval\n");
 	printf("\t                | v4l2-compose | v4l2-interval ;\n");
 	printf("\tv4l2-mbusfmt    = 'fmt:' fcc '/' size ; { 'field:' v4l2-field ; } { 'colorspace:' v4l2-colorspace ; }\n");

;)

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Steve Longerbeam]

On 03/20/2017 07:00 AM, Philipp Zabel wrote:
> On Mon, 2017-03-20 at 12:08 +0000, Russell King - ARM Linux wrote:
>> On Mon, Mar 20, 2017 at 12:55:26PM +0100, Philipp Zabel wrote:
>>> The above paragraph suggests we skip any rectangles that are not
>>> supported. In our case that would be 3. and 4., since the CSI can't
>>> compose into a larger frame. I hadn't realised that the crop selection
>>> currently happens on the source pad.
>> I'd recommend viewing the documentation in its post-processed version,
>> because then you get the examples as pictures, and they say that a
>> picture is worth 1000 words.  See
>>
>>    https://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/dev-subdev.html
>>
>> There is almost an exact example of what we're trying to do - it's
>> figure 4.6.  Here, we have a sink pad with a cropping rectangle on
>> the input, which is then scaled to a composition rectangle (there's
>> no bounds rectangle, and it's specified that in such a case the
>> top,left of the composition rectangle will always be 0,0 - see quote
>> below).
>>
>> Where it differs is that the example also supports source cropping
>> for two source pads.  We don't support that.
>>
>> The same document says:
>>
>>    Scaling support is optional. When supported by a subdev, the crop
>>    rectangle on the subdev's sink pad is scaled to the size configured
>>    using the
>>    :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
>>    using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
>>    subdev supports scaling but not composing, the top and left values are
>>    not used and must always be set to zero.
> Right, this sentence does imply that when scaling is supported, there
> must be a sink compose rectangle, even when composing is not.

Ok, this all makes consistent sense to me too. So:

- the CSI hardware cropping rectangle should be specified via the
   sink pad crop selection.

- the CSI hardware /2 downscaler should be specified via the
   sink pad compose selection.

- the final source pad rectangle is the same as the sink pad
   compose rectangle.

So that leaves only step 4 (source pad crop selection) as
unsupported.

Steve


> I have previously set up scaling like this:
>
> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
>
> Does this mean, it should work like this instead?
>
> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> media-ctl --set-v4l2 "'ipu1_csi0':0[fmt:UYVY2X8/1920x1080@1/60,compose:(0,0)/960x540]"
> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
>
> I suppose setting the source pad format should not be allowed to modify
> the sink compose rectangle.
>
> regards
> Philipp
>

[PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Steve Longerbeam]

On 03/20/2017 07:00 AM, Philipp Zabel wrote:
> On Mon, 2017-03-20 at 12:08 +0000, Russell King - ARM Linux wrote:
>> On Mon, Mar 20, 2017 at 12:55:26PM +0100, Philipp Zabel wrote:
>>> The above paragraph suggests we skip any rectangles that are not
>>> supported. In our case that would be 3. and 4., since the CSI can't
>>> compose into a larger frame. I hadn't realised that the crop selection
>>> currently happens on the source pad.
>> I'd recommend viewing the documentation in its post-processed version,
>> because then you get the examples as pictures, and they say that a
>> picture is worth 1000 words.  See
>>
>>    https://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/dev-subdev.html
>>
>> There is almost an exact example of what we're trying to do - it's
>> figure 4.6.  Here, we have a sink pad with a cropping rectangle on
>> the input, which is then scaled to a composition rectangle (there's
>> no bounds rectangle, and it's specified that in such a case the
>> top,left of the composition rectangle will always be 0,0 - see quote
>> below).
>>
>> Where it differs is that the example also supports source cropping
>> for two source pads.  We don't support that.
>>
>> The same document says:
>>
>>    Scaling support is optional. When supported by a subdev, the crop
>>    rectangle on the subdev's sink pad is scaled to the size configured
>>    using the
>>    :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
>>    using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
>>    subdev supports scaling but not composing, the top and left values are
>>    not used and must always be set to zero.
> Right, this sentence does imply that when scaling is supported, there
> must be a sink compose rectangle, even when composing is not.

Ok, this all makes consistent sense to me too. So:

- the CSI hardware cropping rectangle should be specified via the
   sink pad crop selection.

- the CSI hardware /2 downscaler should be specified via the
   sink pad compose selection.

- the final source pad rectangle is the same as the sink pad
   compose rectangle.

So that leaves only step 4 (source pad crop selection) as
unsupported.

Steve


> I have previously set up scaling like this:
>
> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080 at 1/60]"
> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540 at 1/30]"
>
> Does this mean, it should work like this instead?
>
> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080 at 1/60]"
> media-ctl --set-v4l2 "'ipu1_csi0':0[fmt:UYVY2X8/1920x1080 at 1/60,compose:(0,0)/960x540]"
> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540 at 1/30]"
>
> I suppose setting the source pad format should not be allowed to modify
> the sink compose rectangle.
>
> regards
> Philipp
>

Re: [PATCH v5 38/39] media: imx: csi: fix crop rectangle reset in sink set_fmt

[Steve Longerbeam]

On 03/20/2017 07:00 AM, Philipp Zabel wrote:
> On Mon, 2017-03-20 at 12:08 +0000, Russell King - ARM Linux wrote:
>> On Mon, Mar 20, 2017 at 12:55:26PM +0100, Philipp Zabel wrote:
>>> The above paragraph suggests we skip any rectangles that are not
>>> supported. In our case that would be 3. and 4., since the CSI can't
>>> compose into a larger frame. I hadn't realised that the crop selection
>>> currently happens on the source pad.
>> I'd recommend viewing the documentation in its post-processed version,
>> because then you get the examples as pictures, and they say that a
>> picture is worth 1000 words.  See
>>
>>    https://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/dev-subdev.html
>>
>> There is almost an exact example of what we're trying to do - it's
>> figure 4.6.  Here, we have a sink pad with a cropping rectangle on
>> the input, which is then scaled to a composition rectangle (there's
>> no bounds rectangle, and it's specified that in such a case the
>> top,left of the composition rectangle will always be 0,0 - see quote
>> below).
>>
>> Where it differs is that the example also supports source cropping
>> for two source pads.  We don't support that.
>>
>> The same document says:
>>
>>    Scaling support is optional. When supported by a subdev, the crop
>>    rectangle on the subdev's sink pad is scaled to the size configured
>>    using the
>>    :ref:`VIDIOC_SUBDEV_S_SELECTION <VIDIOC_SUBDEV_G_SELECTION>` IOCTL
>>    using ``V4L2_SEL_TGT_COMPOSE`` selection target on the same pad. If the
>>    subdev supports scaling but not composing, the top and left values are
>>    not used and must always be set to zero.
> Right, this sentence does imply that when scaling is supported, there
> must be a sink compose rectangle, even when composing is not.

Ok, this all makes consistent sense to me too. So:

- the CSI hardware cropping rectangle should be specified via the
   sink pad crop selection.

- the CSI hardware /2 downscaler should be specified via the
   sink pad compose selection.

- the final source pad rectangle is the same as the sink pad
   compose rectangle.

So that leaves only step 4 (source pad crop selection) as
unsupported.

Steve


> I have previously set up scaling like this:
>
> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
>
> Does this mean, it should work like this instead?
>
> media-ctl --set-v4l2 "'ipu1_csi0_mux':2[fmt:UYVY2X8/1920x1080@1/60]"
> media-ctl --set-v4l2 "'ipu1_csi0':0[fmt:UYVY2X8/1920x1080@1/60,compose:(0,0)/960x540]"
> media-ctl --set-v4l2 "'ipu1_csi0':2[fmt:AYUV32/960x540@1/30]"
>
> I suppose setting the source pad format should not be allowed to modify
> the sink compose rectangle.
>
> regards
> Philipp
>

[PATCH v5 39/39] media: imx: propagate sink pad formats to source pads

[Steve Longerbeam]

As part of this, separate format try code from *_set_fmt() into
*_try_fmt(), so that the latter function can be used to propagate
a legal format from sink to source. This also reduces subsequent
bloat in *_set_fmt().

imx-ic-prp never needed separate formats for sink and source pads,
so propagation in this case was easy, just have only a single
format shared by both pads.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/imx-ic-prp.c        |  31 +++---
 drivers/staging/media/imx/imx-ic-prpencvf.c   |  86 ++++++++++-----
 drivers/staging/media/imx/imx-media-capture.c |  12 ++
 drivers/staging/media/imx/imx-media-csi.c     | 152 ++++++++++++++++----------
 drivers/staging/media/imx/imx-media-vdic.c    |  72 +++++++-----
 5 files changed, 224 insertions(+), 129 deletions(-)

diff --git a/drivers/staging/media/imx/imx-ic-prp.c b/drivers/staging/media/imx/imx-ic-prp.c
index 83cd2b4..ec742e6 100644
--- a/drivers/staging/media/imx/imx-ic-prp.c
+++ b/drivers/staging/media/imx/imx-ic-prp.c
@@ -56,8 +56,7 @@ struct prp_priv {
 	/* the CSI id at link validate */
 	int csi_id;
 
-	struct v4l2_mbus_framefmt format_mbus[PRP_NUM_PADS];
-	const struct imx_media_pixfmt *cc[PRP_NUM_PADS];
+	struct v4l2_mbus_framefmt format_mbus;
 	struct v4l2_fract frame_interval;
 
 	bool stream_on; /* streaming is on */
@@ -98,7 +97,7 @@ __prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_pad_config *cfg,
 	if (which == V4L2_SUBDEV_FORMAT_TRY)
 		return v4l2_subdev_get_try_format(&ic_priv->sd, cfg, pad);
 	else
-		return &priv->format_mbus[pad];
+		return &priv->format_mbus;
 }
 
 /*
@@ -167,7 +166,7 @@ static int prp_set_fmt(struct v4l2_subdev *sd,
 		       struct v4l2_subdev_format *sdformat)
 {
 	struct prp_priv *priv = sd_to_priv(sd);
-	const struct imx_media_pixfmt *cc = NULL;
+	const struct imx_media_pixfmt *cc;
 	struct v4l2_mbus_framefmt *infmt;
 	int ret = 0;
 	u32 code;
@@ -201,17 +200,14 @@ static int prp_set_fmt(struct v4l2_subdev *sd,
 		/* Output pads mirror input pad */
 		infmt = __prp_get_fmt(priv, cfg, PRP_SINK_PAD,
 				      sdformat->which);
-		cc = imx_media_find_ipu_format(infmt->code, CS_SEL_ANY);
 		sdformat->format = *infmt;
 		break;
 	}
 
-	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
+	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY)
 		cfg->try_fmt = sdformat->format;
-	} else {
-		priv->format_mbus[sdformat->pad] = sdformat->format;
-		priv->cc[sdformat->pad] = cc;
-	}
+	else
+		priv->format_mbus = sdformat->format;
 
 out:
 	mutex_unlock(&priv->lock);
@@ -427,20 +423,19 @@ static int prp_registered(struct v4l2_subdev *sd)
 	for (i = 0; i < PRP_NUM_PADS; i++) {
 		priv->pad[i].flags = (i == PRP_SINK_PAD) ?
 			MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
-
-		/* set a default mbus format  */
-		imx_media_enum_ipu_format(&code, 0, CS_SEL_YUV);
-		ret = imx_media_init_mbus_fmt(&priv->format_mbus[i],
-					      640, 480, code, V4L2_FIELD_NONE,
-					      &priv->cc[i]);
-		if (ret)
-			return ret;
 	}
 
 	/* init default frame interval */
 	priv->frame_interval.numerator = 1;
 	priv->frame_interval.denominator = 30;
 
+	/* set a default mbus format  */
+	imx_media_enum_ipu_format(&code, 0, CS_SEL_YUV);
+	ret = imx_media_init_mbus_fmt(&priv->format_mbus, 640, 480, code,
+				      V4L2_FIELD_NONE, NULL);
+	if (ret)
+		return ret;
+
 	return media_entity_pads_init(&sd->entity, PRP_NUM_PADS, priv->pad);
 }
 
diff --git a/drivers/staging/media/imx/imx-ic-prpencvf.c b/drivers/staging/media/imx/imx-ic-prpencvf.c
index b42103c..644dd33 100644
--- a/drivers/staging/media/imx/imx-ic-prpencvf.c
+++ b/drivers/staging/media/imx/imx-ic-prpencvf.c
@@ -753,35 +753,23 @@ static int prp_get_fmt(struct v4l2_subdev *sd,
 	return ret;
 }
 
-static int prp_set_fmt(struct v4l2_subdev *sd,
-		       struct v4l2_subdev_pad_config *cfg,
-		       struct v4l2_subdev_format *sdformat)
+static void prp_try_fmt(struct prp_priv *priv,
+			struct v4l2_subdev_pad_config *cfg,
+			struct v4l2_subdev_format *sdformat,
+			const struct imx_media_pixfmt **cc)
 {
-	struct prp_priv *priv = sd_to_priv(sd);
-	const struct imx_media_pixfmt *cc;
-	struct v4l2_mbus_framefmt *infmt;
-	int ret = 0;
-	u32 code;
-
-	if (sdformat->pad >= PRPENCVF_NUM_PADS)
-		return -EINVAL;
-
-	mutex_lock(&priv->lock);
+	*cc = imx_media_find_ipu_format(sdformat->format.code, CS_SEL_ANY);
+	if (!*cc) {
+		u32 code;
 
-	if (priv->stream_on) {
-		ret = -EBUSY;
-		goto out;
-	}
-
-	cc = imx_media_find_ipu_format(sdformat->format.code, CS_SEL_ANY);
-	if (!cc) {
 		imx_media_enum_ipu_format(&code, 0, CS_SEL_ANY);
-		cc = imx_media_find_ipu_format(code, CS_SEL_ANY);
-		sdformat->format.code = cc->codes[0];
+		*cc = imx_media_find_ipu_format(code, CS_SEL_ANY);
+		sdformat->format.code = (*cc)->codes[0];
 	}
 
 	if (sdformat->pad == PRPENCVF_SRC_PAD) {
-		infmt = __prp_get_fmt(priv, cfg, PRPENCVF_SINK_PAD,
+		struct v4l2_mbus_framefmt *infmt =
+			__prp_get_fmt(priv, cfg, PRPENCVF_SINK_PAD,
 				      sdformat->which);
 
 		if (sdformat->format.field != V4L2_FIELD_NONE)
@@ -809,14 +797,60 @@ static int prp_set_fmt(struct v4l2_subdev *sd,
 				      MIN_H_SINK, MAX_H_SINK, H_ALIGN_SINK,
 				      S_ALIGN);
 	}
+}
+
+static int prp_set_fmt(struct v4l2_subdev *sd,
+		       struct v4l2_subdev_pad_config *cfg,
+		       struct v4l2_subdev_format *sdformat)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+	struct imx_media_video_dev *vdev = priv->vdev;
+	const struct imx_media_pixfmt *cc;
+	struct v4l2_pix_format vdev_fmt;
+	int ret = 0;
+
+	if (sdformat->pad >= PRPENCVF_NUM_PADS)
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	if (priv->stream_on) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	prp_try_fmt(priv, cfg, sdformat, &cc);
 
 	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
 		cfg->try_fmt = sdformat->format;
-	} else {
-		priv->format_mbus[sdformat->pad] = sdformat->format;
-		priv->cc[sdformat->pad] = cc;
+		goto out;
+	}
+
+	priv->format_mbus[sdformat->pad] = sdformat->format;
+	priv->cc[sdformat->pad] = cc;
+
+	/* propagate a default format to source pad */
+	if (sdformat->pad == PRPENCVF_SINK_PAD) {
+		const struct imx_media_pixfmt *outcc;
+		struct v4l2_subdev_format format;
+
+		format.pad = PRPENCVF_SRC_PAD;
+		format.which = V4L2_SUBDEV_FORMAT_ACTIVE;
+		format.format = sdformat->format;
+		prp_try_fmt(priv, cfg, &format, &outcc);
+
+		priv->format_mbus[PRPENCVF_SRC_PAD] = format.format;
+		priv->cc[PRPENCVF_SRC_PAD] = outcc;
 	}
 
+	/* propagate output pad format to capture device */
+	imx_media_mbus_fmt_to_pix_fmt(&vdev_fmt,
+				      &priv->format_mbus[PRPENCVF_SRC_PAD],
+				      priv->cc[PRPENCVF_SRC_PAD]);
+	mutex_unlock(&priv->lock);
+	imx_media_capture_device_set_format(vdev, &vdev_fmt);
+
+	return 0;
 out:
 	mutex_unlock(&priv->lock);
 	return ret;
diff --git a/drivers/staging/media/imx/imx-media-capture.c b/drivers/staging/media/imx/imx-media-capture.c
index a757e05..ee91439 100644
--- a/drivers/staging/media/imx/imx-media-capture.c
+++ b/drivers/staging/media/imx/imx-media-capture.c
@@ -498,6 +498,18 @@ static struct video_device capture_videodev = {
 	.device_caps	= V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING,
 };
 
+void imx_media_capture_device_set_format(struct imx_media_video_dev *vdev,
+					 struct v4l2_pix_format *pix)
+{
+	struct capture_priv *priv = to_capture_priv(vdev);
+
+	mutex_lock(&priv->mutex);
+	priv->vdev.fmt.fmt.pix = *pix;
+	priv->vdev.cc = imx_media_find_format(pix->pixelformat, CS_SEL_ANY);
+	mutex_unlock(&priv->mutex);
+}
+EXPORT_SYMBOL_GPL(imx_media_capture_device_set_format);
+
 struct imx_media_buffer *
 imx_media_capture_device_next_buf(struct imx_media_video_dev *vdev)
 {
diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index cf070be..fc0036a 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -986,11 +986,11 @@ __csi_get_fmt(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
 		return &priv->format_mbus[pad];
 }
 
-static int csi_try_crop(struct csi_priv *priv,
-			struct v4l2_rect *crop,
-			struct v4l2_subdev_pad_config *cfg,
-			struct v4l2_mbus_framefmt *infmt,
-			struct imx_media_subdev *sensor)
+static void csi_try_crop(struct csi_priv *priv,
+			 struct v4l2_rect *crop,
+			 struct v4l2_subdev_pad_config *cfg,
+			 struct v4l2_mbus_framefmt *infmt,
+			 struct imx_media_subdev *sensor)
 {
 	struct v4l2_of_endpoint *sensor_ep;
 
@@ -1019,8 +1019,6 @@ static int csi_try_crop(struct csi_priv *priv,
 		if (crop->top + crop->height > infmt->height)
 			crop->top = infmt->height - crop->height;
 	}
-
-	return 0;
 }
 
 static int csi_enum_mbus_code(struct v4l2_subdev *sd,
@@ -1092,34 +1090,17 @@ static int csi_get_fmt(struct v4l2_subdev *sd,
 	return ret;
 }
 
-static int csi_set_fmt(struct v4l2_subdev *sd,
-		       struct v4l2_subdev_pad_config *cfg,
-		       struct v4l2_subdev_format *sdformat)
+static void csi_try_fmt(struct csi_priv *priv,
+			struct imx_media_subdev *sensor,
+			struct v4l2_subdev_pad_config *cfg,
+			struct v4l2_subdev_format *sdformat,
+			struct v4l2_rect *crop,
+			const struct imx_media_pixfmt **cc)
 {
-	struct csi_priv *priv = v4l2_get_subdevdata(sd);
-	const struct imx_media_pixfmt *cc, *incc;
+	const struct imx_media_pixfmt *incc;
 	struct v4l2_mbus_framefmt *infmt;
-	struct imx_media_subdev *sensor;
-	struct v4l2_rect crop;
-	int ret = 0;
 	u32 code;
 
-	if (sdformat->pad >= CSI_NUM_PADS)
-		return -EINVAL;
-
-	sensor = imx_media_find_sensor(priv->md, &priv->sd.entity);
-	if (IS_ERR(sensor)) {
-		v4l2_err(&priv->sd, "no sensor attached\n");
-		return PTR_ERR(sensor);
-	}
-
-	mutex_lock(&priv->lock);
-
-	if (priv->stream_on) {
-		ret = -EBUSY;
-		goto out;
-	}
-
 	switch (sdformat->pad) {
 	case CSI_SRC_PAD_DIRECT:
 	case CSI_SRC_PAD_IDMAC:
@@ -1140,17 +1121,17 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 
 		if (incc->bayer) {
 			sdformat->format.code = infmt->code;
-			cc = incc;
+			*cc = incc;
 		} else {
 			u32 cs_sel = (incc->cs == IPUV3_COLORSPACE_YUV) ?
 				CS_SEL_YUV : CS_SEL_RGB;
 
-			cc = imx_media_find_ipu_format(sdformat->format.code,
-						       cs_sel);
-			if (!cc) {
+			*cc = imx_media_find_ipu_format(sdformat->format.code,
+							cs_sel);
+			if (!*cc) {
 				imx_media_enum_ipu_format(&code, 0, cs_sel);
-				cc = imx_media_find_ipu_format(code, cs_sel);
-				sdformat->format.code = cc->codes[0];
+				*cc = imx_media_find_ipu_format(code, cs_sel);
+				sdformat->format.code = (*cc)->codes[0];
 			}
 		}
 
@@ -1172,39 +1153,92 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 		v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
 				      W_ALIGN, &sdformat->format.height,
 				      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
-		crop.left = 0;
-		crop.top = 0;
-		crop.width = sdformat->format.width;
-		crop.height = sdformat->format.height;
-		ret = csi_try_crop(priv, &crop, cfg, &sdformat->format, sensor);
-		if (ret)
-			goto out;
+		crop->left = 0;
+		crop->top = 0;
+		crop->width = sdformat->format.width;
+		crop->height = sdformat->format.height;
+		csi_try_crop(priv, crop, cfg, &sdformat->format, sensor);
 
-		cc = imx_media_find_mbus_format(sdformat->format.code,
-						CS_SEL_ANY, true);
-		if (!cc) {
+		*cc = imx_media_find_mbus_format(sdformat->format.code,
+						 CS_SEL_ANY, true);
+		if (!*cc) {
 			imx_media_enum_mbus_format(&code, 0,
 						   CS_SEL_ANY, false);
-			cc = imx_media_find_mbus_format(code,
+			*cc = imx_media_find_mbus_format(code,
 							CS_SEL_ANY, false);
-			sdformat->format.code = cc->codes[0];
+			sdformat->format.code = (*cc)->codes[0];
 		}
 		break;
-	default:
-		ret = -EINVAL;
+	}
+}
+
+static int csi_set_fmt(struct v4l2_subdev *sd,
+		       struct v4l2_subdev_pad_config *cfg,
+		       struct v4l2_subdev_format *sdformat)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct imx_media_video_dev *vdev = priv->vdev;
+	const struct imx_media_pixfmt *cc;
+	struct imx_media_subdev *sensor;
+	struct v4l2_pix_format vdev_fmt;
+	struct v4l2_rect crop;
+	int ret = 0;
+
+	if (sdformat->pad >= CSI_NUM_PADS)
+		return -EINVAL;
+
+	sensor = imx_media_find_sensor(priv->md, &priv->sd.entity);
+	if (IS_ERR(sensor)) {
+		v4l2_err(&priv->sd, "no sensor attached\n");
+		return PTR_ERR(sensor);
+	}
+
+	mutex_lock(&priv->lock);
+
+	if (priv->stream_on) {
+		ret = -EBUSY;
 		goto out;
 	}
 
+	csi_try_fmt(priv, sensor, cfg, sdformat, &crop, &cc);
+
 	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
 		cfg->try_fmt = sdformat->format;
-	} else {
-		priv->format_mbus[sdformat->pad] = sdformat->format;
-		priv->cc[sdformat->pad] = cc;
-		/* Reset the crop window if this is the input pad */
-		if (sdformat->pad == CSI_SINK_PAD)
-			priv->crop = crop;
+		goto out;
 	}
 
+	priv->format_mbus[sdformat->pad] = sdformat->format;
+	priv->cc[sdformat->pad] = cc;
+
+	if (sdformat->pad == CSI_SINK_PAD) {
+		int pad;
+
+		/* reset the crop window */
+		priv->crop = crop;
+
+		/* propagate format to source pads */
+		for (pad = CSI_SINK_PAD + 1; pad < CSI_NUM_PADS; pad++) {
+			const struct imx_media_pixfmt *outcc;
+			struct v4l2_subdev_format format;
+
+			format.pad = pad;
+			format.which = V4L2_SUBDEV_FORMAT_ACTIVE;
+			format.format = sdformat->format;
+			csi_try_fmt(priv, sensor, cfg, &format, &crop, &outcc);
+
+			priv->format_mbus[pad] = format.format;
+			priv->cc[pad] = outcc;
+		}
+	}
+
+	/* propagate IDMAC output pad format to capture device */
+	imx_media_mbus_fmt_to_pix_fmt(&vdev_fmt,
+				      &priv->format_mbus[CSI_SRC_PAD_IDMAC],
+				      priv->cc[CSI_SRC_PAD_IDMAC]);
+	mutex_unlock(&priv->lock);
+	imx_media_capture_device_set_format(vdev, &vdev_fmt);
+
+	return 0;
 out:
 	mutex_unlock(&priv->lock);
 	return ret;
@@ -1295,9 +1329,7 @@ static int csi_set_selection(struct v4l2_subdev *sd,
 	}
 
 	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
-	ret = csi_try_crop(priv, &sel->r, cfg, infmt, sensor);
-	if (ret)
-		goto out;
+	csi_try_crop(priv, &sel->r, cfg, infmt, sensor);
 
 	if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
 		cfg->try_crop = sel->r;
diff --git a/drivers/staging/media/imx/imx-media-vdic.c b/drivers/staging/media/imx/imx-media-vdic.c
index 070f9da..58eda18 100644
--- a/drivers/staging/media/imx/imx-media-vdic.c
+++ b/drivers/staging/media/imx/imx-media-vdic.c
@@ -562,31 +562,20 @@ static int vdic_get_fmt(struct v4l2_subdev *sd,
 	return ret;
 }
 
-static int vdic_set_fmt(struct v4l2_subdev *sd,
-			struct v4l2_subdev_pad_config *cfg,
-			struct v4l2_subdev_format *sdformat)
+static void vdic_try_fmt(struct vdic_priv *priv,
+			 struct v4l2_subdev_pad_config *cfg,
+			 struct v4l2_subdev_format *sdformat,
+			 const struct imx_media_pixfmt **cc)
 {
-	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
-	const struct imx_media_pixfmt *cc;
 	struct v4l2_mbus_framefmt *infmt;
-	int ret = 0;
-	u32 code;
-
-	if (sdformat->pad >= VDIC_NUM_PADS)
-		return -EINVAL;
-
-	mutex_lock(&priv->lock);
 
-	if (priv->stream_on) {
-		ret = -EBUSY;
-		goto out;
-	}
+	*cc = imx_media_find_ipu_format(sdformat->format.code, CS_SEL_YUV);
+	if (!*cc) {
+		u32 code;
 
-	cc = imx_media_find_ipu_format(sdformat->format.code, CS_SEL_YUV);
-	if (!cc) {
 		imx_media_enum_ipu_format(&code, 0, CS_SEL_YUV);
-		cc = imx_media_find_ipu_format(code, CS_SEL_YUV);
-		sdformat->format.code = cc->codes[0];
+		*cc = imx_media_find_ipu_format(code, CS_SEL_YUV);
+		sdformat->format.code = (*cc)->codes[0];
 	}
 
 	switch (sdformat->pad) {
@@ -609,18 +598,51 @@ static int vdic_set_fmt(struct v4l2_subdev *sd,
 		if (!V4L2_FIELD_HAS_BOTH(sdformat->format.field))
 			sdformat->format.field = V4L2_FIELD_SEQ_TB;
 		break;
-	default:
-		ret = -EINVAL;
+	}
+}
+
+static int vdic_set_fmt(struct v4l2_subdev *sd,
+			struct v4l2_subdev_pad_config *cfg,
+			struct v4l2_subdev_format *sdformat)
+{
+	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
+	const struct imx_media_pixfmt *cc;
+	int ret = 0;
+
+	if (sdformat->pad >= VDIC_NUM_PADS)
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	if (priv->stream_on) {
+		ret = -EBUSY;
 		goto out;
 	}
 
+	vdic_try_fmt(priv, cfg, sdformat, &cc);
+
 	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
 		cfg->try_fmt = sdformat->format;
-	} else {
-		priv->format_mbus[sdformat->pad] = sdformat->format;
-		priv->cc[sdformat->pad] = cc;
+		goto out;
 	}
 
+	priv->format_mbus[sdformat->pad] = sdformat->format;
+	priv->cc[sdformat->pad] = cc;
+
+	/* propagate format to source pad */
+	if (sdformat->pad == VDIC_SINK_PAD_DIRECT ||
+	    sdformat->pad == VDIC_SINK_PAD_IDMAC) {
+		const struct imx_media_pixfmt *outcc;
+		struct v4l2_subdev_format format;
+
+		format.pad = VDIC_SRC_PAD_DIRECT;
+		format.which = V4L2_SUBDEV_FORMAT_ACTIVE;
+		format.format = sdformat->format;
+		vdic_try_fmt(priv, cfg, &format, &outcc);
+
+		priv->format_mbus[VDIC_SRC_PAD_DIRECT] = format.format;
+		priv->cc[VDIC_SRC_PAD_DIRECT] = outcc;
+	}
 out:
 	mutex_unlock(&priv->lock);
 	return ret;
-- 
2.7.4

[PATCH v5 39/39] media: imx: propagate sink pad formats to source pads

[Steve Longerbeam]

As part of this, separate format try code from *_set_fmt() into
*_try_fmt(), so that the latter function can be used to propagate
a legal format from sink to source. This also reduces subsequent
bloat in *_set_fmt().

imx-ic-prp never needed separate formats for sink and source pads,
so propagation in this case was easy, just have only a single
format shared by both pads.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/imx-ic-prp.c        |  31 +++---
 drivers/staging/media/imx/imx-ic-prpencvf.c   |  86 ++++++++++-----
 drivers/staging/media/imx/imx-media-capture.c |  12 ++
 drivers/staging/media/imx/imx-media-csi.c     | 152 ++++++++++++++++----------
 drivers/staging/media/imx/imx-media-vdic.c    |  72 +++++++-----
 5 files changed, 224 insertions(+), 129 deletions(-)

diff --git a/drivers/staging/media/imx/imx-ic-prp.c b/drivers/staging/media/imx/imx-ic-prp.c
index 83cd2b4..ec742e6 100644
--- a/drivers/staging/media/imx/imx-ic-prp.c
+++ b/drivers/staging/media/imx/imx-ic-prp.c
@@ -56,8 +56,7 @@ struct prp_priv {
 	/* the CSI id at link validate */
 	int csi_id;
 
-	struct v4l2_mbus_framefmt format_mbus[PRP_NUM_PADS];
-	const struct imx_media_pixfmt *cc[PRP_NUM_PADS];
+	struct v4l2_mbus_framefmt format_mbus;
 	struct v4l2_fract frame_interval;
 
 	bool stream_on; /* streaming is on */
@@ -98,7 +97,7 @@ __prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_pad_config *cfg,
 	if (which == V4L2_SUBDEV_FORMAT_TRY)
 		return v4l2_subdev_get_try_format(&ic_priv->sd, cfg, pad);
 	else
-		return &priv->format_mbus[pad];
+		return &priv->format_mbus;
 }
 
 /*
@@ -167,7 +166,7 @@ static int prp_set_fmt(struct v4l2_subdev *sd,
 		       struct v4l2_subdev_format *sdformat)
 {
 	struct prp_priv *priv = sd_to_priv(sd);
-	const struct imx_media_pixfmt *cc = NULL;
+	const struct imx_media_pixfmt *cc;
 	struct v4l2_mbus_framefmt *infmt;
 	int ret = 0;
 	u32 code;
@@ -201,17 +200,14 @@ static int prp_set_fmt(struct v4l2_subdev *sd,
 		/* Output pads mirror input pad */
 		infmt = __prp_get_fmt(priv, cfg, PRP_SINK_PAD,
 				      sdformat->which);
-		cc = imx_media_find_ipu_format(infmt->code, CS_SEL_ANY);
 		sdformat->format = *infmt;
 		break;
 	}
 
-	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
+	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY)
 		cfg->try_fmt = sdformat->format;
-	} else {
-		priv->format_mbus[sdformat->pad] = sdformat->format;
-		priv->cc[sdformat->pad] = cc;
-	}
+	else
+		priv->format_mbus = sdformat->format;
 
 out:
 	mutex_unlock(&priv->lock);
@@ -427,20 +423,19 @@ static int prp_registered(struct v4l2_subdev *sd)
 	for (i = 0; i < PRP_NUM_PADS; i++) {
 		priv->pad[i].flags = (i == PRP_SINK_PAD) ?
 			MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
-
-		/* set a default mbus format  */
-		imx_media_enum_ipu_format(&code, 0, CS_SEL_YUV);
-		ret = imx_media_init_mbus_fmt(&priv->format_mbus[i],
-					      640, 480, code, V4L2_FIELD_NONE,
-					      &priv->cc[i]);
-		if (ret)
-			return ret;
 	}
 
 	/* init default frame interval */
 	priv->frame_interval.numerator = 1;
 	priv->frame_interval.denominator = 30;
 
+	/* set a default mbus format  */
+	imx_media_enum_ipu_format(&code, 0, CS_SEL_YUV);
+	ret = imx_media_init_mbus_fmt(&priv->format_mbus, 640, 480, code,
+				      V4L2_FIELD_NONE, NULL);
+	if (ret)
+		return ret;
+
 	return media_entity_pads_init(&sd->entity, PRP_NUM_PADS, priv->pad);
 }
 
diff --git a/drivers/staging/media/imx/imx-ic-prpencvf.c b/drivers/staging/media/imx/imx-ic-prpencvf.c
index b42103c..644dd33 100644
--- a/drivers/staging/media/imx/imx-ic-prpencvf.c
+++ b/drivers/staging/media/imx/imx-ic-prpencvf.c
@@ -753,35 +753,23 @@ static int prp_get_fmt(struct v4l2_subdev *sd,
 	return ret;
 }
 
-static int prp_set_fmt(struct v4l2_subdev *sd,
-		       struct v4l2_subdev_pad_config *cfg,
-		       struct v4l2_subdev_format *sdformat)
+static void prp_try_fmt(struct prp_priv *priv,
+			struct v4l2_subdev_pad_config *cfg,
+			struct v4l2_subdev_format *sdformat,
+			const struct imx_media_pixfmt **cc)
 {
-	struct prp_priv *priv = sd_to_priv(sd);
-	const struct imx_media_pixfmt *cc;
-	struct v4l2_mbus_framefmt *infmt;
-	int ret = 0;
-	u32 code;
-
-	if (sdformat->pad >= PRPENCVF_NUM_PADS)
-		return -EINVAL;
-
-	mutex_lock(&priv->lock);
+	*cc = imx_media_find_ipu_format(sdformat->format.code, CS_SEL_ANY);
+	if (!*cc) {
+		u32 code;
 
-	if (priv->stream_on) {
-		ret = -EBUSY;
-		goto out;
-	}
-
-	cc = imx_media_find_ipu_format(sdformat->format.code, CS_SEL_ANY);
-	if (!cc) {
 		imx_media_enum_ipu_format(&code, 0, CS_SEL_ANY);
-		cc = imx_media_find_ipu_format(code, CS_SEL_ANY);
-		sdformat->format.code = cc->codes[0];
+		*cc = imx_media_find_ipu_format(code, CS_SEL_ANY);
+		sdformat->format.code = (*cc)->codes[0];
 	}
 
 	if (sdformat->pad == PRPENCVF_SRC_PAD) {
-		infmt = __prp_get_fmt(priv, cfg, PRPENCVF_SINK_PAD,
+		struct v4l2_mbus_framefmt *infmt =
+			__prp_get_fmt(priv, cfg, PRPENCVF_SINK_PAD,
 				      sdformat->which);
 
 		if (sdformat->format.field != V4L2_FIELD_NONE)
@@ -809,14 +797,60 @@ static int prp_set_fmt(struct v4l2_subdev *sd,
 				      MIN_H_SINK, MAX_H_SINK, H_ALIGN_SINK,
 				      S_ALIGN);
 	}
+}
+
+static int prp_set_fmt(struct v4l2_subdev *sd,
+		       struct v4l2_subdev_pad_config *cfg,
+		       struct v4l2_subdev_format *sdformat)
+{
+	struct prp_priv *priv = sd_to_priv(sd);
+	struct imx_media_video_dev *vdev = priv->vdev;
+	const struct imx_media_pixfmt *cc;
+	struct v4l2_pix_format vdev_fmt;
+	int ret = 0;
+
+	if (sdformat->pad >= PRPENCVF_NUM_PADS)
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	if (priv->stream_on) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	prp_try_fmt(priv, cfg, sdformat, &cc);
 
 	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
 		cfg->try_fmt = sdformat->format;
-	} else {
-		priv->format_mbus[sdformat->pad] = sdformat->format;
-		priv->cc[sdformat->pad] = cc;
+		goto out;
+	}
+
+	priv->format_mbus[sdformat->pad] = sdformat->format;
+	priv->cc[sdformat->pad] = cc;
+
+	/* propagate a default format to source pad */
+	if (sdformat->pad == PRPENCVF_SINK_PAD) {
+		const struct imx_media_pixfmt *outcc;
+		struct v4l2_subdev_format format;
+
+		format.pad = PRPENCVF_SRC_PAD;
+		format.which = V4L2_SUBDEV_FORMAT_ACTIVE;
+		format.format = sdformat->format;
+		prp_try_fmt(priv, cfg, &format, &outcc);
+
+		priv->format_mbus[PRPENCVF_SRC_PAD] = format.format;
+		priv->cc[PRPENCVF_SRC_PAD] = outcc;
 	}
 
+	/* propagate output pad format to capture device */
+	imx_media_mbus_fmt_to_pix_fmt(&vdev_fmt,
+				      &priv->format_mbus[PRPENCVF_SRC_PAD],
+				      priv->cc[PRPENCVF_SRC_PAD]);
+	mutex_unlock(&priv->lock);
+	imx_media_capture_device_set_format(vdev, &vdev_fmt);
+
+	return 0;
 out:
 	mutex_unlock(&priv->lock);
 	return ret;
diff --git a/drivers/staging/media/imx/imx-media-capture.c b/drivers/staging/media/imx/imx-media-capture.c
index a757e05..ee91439 100644
--- a/drivers/staging/media/imx/imx-media-capture.c
+++ b/drivers/staging/media/imx/imx-media-capture.c
@@ -498,6 +498,18 @@ static struct video_device capture_videodev = {
 	.device_caps	= V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING,
 };
 
+void imx_media_capture_device_set_format(struct imx_media_video_dev *vdev,
+					 struct v4l2_pix_format *pix)
+{
+	struct capture_priv *priv = to_capture_priv(vdev);
+
+	mutex_lock(&priv->mutex);
+	priv->vdev.fmt.fmt.pix = *pix;
+	priv->vdev.cc = imx_media_find_format(pix->pixelformat, CS_SEL_ANY);
+	mutex_unlock(&priv->mutex);
+}
+EXPORT_SYMBOL_GPL(imx_media_capture_device_set_format);
+
 struct imx_media_buffer *
 imx_media_capture_device_next_buf(struct imx_media_video_dev *vdev)
 {
diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index cf070be..fc0036a 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -986,11 +986,11 @@ __csi_get_fmt(struct csi_priv *priv, struct v4l2_subdev_pad_config *cfg,
 		return &priv->format_mbus[pad];
 }
 
-static int csi_try_crop(struct csi_priv *priv,
-			struct v4l2_rect *crop,
-			struct v4l2_subdev_pad_config *cfg,
-			struct v4l2_mbus_framefmt *infmt,
-			struct imx_media_subdev *sensor)
+static void csi_try_crop(struct csi_priv *priv,
+			 struct v4l2_rect *crop,
+			 struct v4l2_subdev_pad_config *cfg,
+			 struct v4l2_mbus_framefmt *infmt,
+			 struct imx_media_subdev *sensor)
 {
 	struct v4l2_of_endpoint *sensor_ep;
 
@@ -1019,8 +1019,6 @@ static int csi_try_crop(struct csi_priv *priv,
 		if (crop->top + crop->height > infmt->height)
 			crop->top = infmt->height - crop->height;
 	}
-
-	return 0;
 }
 
 static int csi_enum_mbus_code(struct v4l2_subdev *sd,
@@ -1092,34 +1090,17 @@ static int csi_get_fmt(struct v4l2_subdev *sd,
 	return ret;
 }
 
-static int csi_set_fmt(struct v4l2_subdev *sd,
-		       struct v4l2_subdev_pad_config *cfg,
-		       struct v4l2_subdev_format *sdformat)
+static void csi_try_fmt(struct csi_priv *priv,
+			struct imx_media_subdev *sensor,
+			struct v4l2_subdev_pad_config *cfg,
+			struct v4l2_subdev_format *sdformat,
+			struct v4l2_rect *crop,
+			const struct imx_media_pixfmt **cc)
 {
-	struct csi_priv *priv = v4l2_get_subdevdata(sd);
-	const struct imx_media_pixfmt *cc, *incc;
+	const struct imx_media_pixfmt *incc;
 	struct v4l2_mbus_framefmt *infmt;
-	struct imx_media_subdev *sensor;
-	struct v4l2_rect crop;
-	int ret = 0;
 	u32 code;
 
-	if (sdformat->pad >= CSI_NUM_PADS)
-		return -EINVAL;
-
-	sensor = imx_media_find_sensor(priv->md, &priv->sd.entity);
-	if (IS_ERR(sensor)) {
-		v4l2_err(&priv->sd, "no sensor attached\n");
-		return PTR_ERR(sensor);
-	}
-
-	mutex_lock(&priv->lock);
-
-	if (priv->stream_on) {
-		ret = -EBUSY;
-		goto out;
-	}
-
 	switch (sdformat->pad) {
 	case CSI_SRC_PAD_DIRECT:
 	case CSI_SRC_PAD_IDMAC:
@@ -1140,17 +1121,17 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 
 		if (incc->bayer) {
 			sdformat->format.code = infmt->code;
-			cc = incc;
+			*cc = incc;
 		} else {
 			u32 cs_sel = (incc->cs == IPUV3_COLORSPACE_YUV) ?
 				CS_SEL_YUV : CS_SEL_RGB;
 
-			cc = imx_media_find_ipu_format(sdformat->format.code,
-						       cs_sel);
-			if (!cc) {
+			*cc = imx_media_find_ipu_format(sdformat->format.code,
+							cs_sel);
+			if (!*cc) {
 				imx_media_enum_ipu_format(&code, 0, cs_sel);
-				cc = imx_media_find_ipu_format(code, cs_sel);
-				sdformat->format.code = cc->codes[0];
+				*cc = imx_media_find_ipu_format(code, cs_sel);
+				sdformat->format.code = (*cc)->codes[0];
 			}
 		}
 
@@ -1172,39 +1153,92 @@ static int csi_set_fmt(struct v4l2_subdev *sd,
 		v4l_bound_align_image(&sdformat->format.width, MIN_W, MAX_W,
 				      W_ALIGN, &sdformat->format.height,
 				      MIN_H, MAX_H, H_ALIGN, S_ALIGN);
-		crop.left = 0;
-		crop.top = 0;
-		crop.width = sdformat->format.width;
-		crop.height = sdformat->format.height;
-		ret = csi_try_crop(priv, &crop, cfg, &sdformat->format, sensor);
-		if (ret)
-			goto out;
+		crop->left = 0;
+		crop->top = 0;
+		crop->width = sdformat->format.width;
+		crop->height = sdformat->format.height;
+		csi_try_crop(priv, crop, cfg, &sdformat->format, sensor);
 
-		cc = imx_media_find_mbus_format(sdformat->format.code,
-						CS_SEL_ANY, true);
-		if (!cc) {
+		*cc = imx_media_find_mbus_format(sdformat->format.code,
+						 CS_SEL_ANY, true);
+		if (!*cc) {
 			imx_media_enum_mbus_format(&code, 0,
 						   CS_SEL_ANY, false);
-			cc = imx_media_find_mbus_format(code,
+			*cc = imx_media_find_mbus_format(code,
 							CS_SEL_ANY, false);
-			sdformat->format.code = cc->codes[0];
+			sdformat->format.code = (*cc)->codes[0];
 		}
 		break;
-	default:
-		ret = -EINVAL;
+	}
+}
+
+static int csi_set_fmt(struct v4l2_subdev *sd,
+		       struct v4l2_subdev_pad_config *cfg,
+		       struct v4l2_subdev_format *sdformat)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct imx_media_video_dev *vdev = priv->vdev;
+	const struct imx_media_pixfmt *cc;
+	struct imx_media_subdev *sensor;
+	struct v4l2_pix_format vdev_fmt;
+	struct v4l2_rect crop;
+	int ret = 0;
+
+	if (sdformat->pad >= CSI_NUM_PADS)
+		return -EINVAL;
+
+	sensor = imx_media_find_sensor(priv->md, &priv->sd.entity);
+	if (IS_ERR(sensor)) {
+		v4l2_err(&priv->sd, "no sensor attached\n");
+		return PTR_ERR(sensor);
+	}
+
+	mutex_lock(&priv->lock);
+
+	if (priv->stream_on) {
+		ret = -EBUSY;
 		goto out;
 	}
 
+	csi_try_fmt(priv, sensor, cfg, sdformat, &crop, &cc);
+
 	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
 		cfg->try_fmt = sdformat->format;
-	} else {
-		priv->format_mbus[sdformat->pad] = sdformat->format;
-		priv->cc[sdformat->pad] = cc;
-		/* Reset the crop window if this is the input pad */
-		if (sdformat->pad == CSI_SINK_PAD)
-			priv->crop = crop;
+		goto out;
 	}
 
+	priv->format_mbus[sdformat->pad] = sdformat->format;
+	priv->cc[sdformat->pad] = cc;
+
+	if (sdformat->pad == CSI_SINK_PAD) {
+		int pad;
+
+		/* reset the crop window */
+		priv->crop = crop;
+
+		/* propagate format to source pads */
+		for (pad = CSI_SINK_PAD + 1; pad < CSI_NUM_PADS; pad++) {
+			const struct imx_media_pixfmt *outcc;
+			struct v4l2_subdev_format format;
+
+			format.pad = pad;
+			format.which = V4L2_SUBDEV_FORMAT_ACTIVE;
+			format.format = sdformat->format;
+			csi_try_fmt(priv, sensor, cfg, &format, &crop, &outcc);
+
+			priv->format_mbus[pad] = format.format;
+			priv->cc[pad] = outcc;
+		}
+	}
+
+	/* propagate IDMAC output pad format to capture device */
+	imx_media_mbus_fmt_to_pix_fmt(&vdev_fmt,
+				      &priv->format_mbus[CSI_SRC_PAD_IDMAC],
+				      priv->cc[CSI_SRC_PAD_IDMAC]);
+	mutex_unlock(&priv->lock);
+	imx_media_capture_device_set_format(vdev, &vdev_fmt);
+
+	return 0;
 out:
 	mutex_unlock(&priv->lock);
 	return ret;
@@ -1295,9 +1329,7 @@ static int csi_set_selection(struct v4l2_subdev *sd,
 	}
 
 	infmt = __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sel->which);
-	ret = csi_try_crop(priv, &sel->r, cfg, infmt, sensor);
-	if (ret)
-		goto out;
+	csi_try_crop(priv, &sel->r, cfg, infmt, sensor);
 
 	if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
 		cfg->try_crop = sel->r;
diff --git a/drivers/staging/media/imx/imx-media-vdic.c b/drivers/staging/media/imx/imx-media-vdic.c
index 070f9da..58eda18 100644
--- a/drivers/staging/media/imx/imx-media-vdic.c
+++ b/drivers/staging/media/imx/imx-media-vdic.c
@@ -562,31 +562,20 @@ static int vdic_get_fmt(struct v4l2_subdev *sd,
 	return ret;
 }
 
-static int vdic_set_fmt(struct v4l2_subdev *sd,
-			struct v4l2_subdev_pad_config *cfg,
-			struct v4l2_subdev_format *sdformat)
+static void vdic_try_fmt(struct vdic_priv *priv,
+			 struct v4l2_subdev_pad_config *cfg,
+			 struct v4l2_subdev_format *sdformat,
+			 const struct imx_media_pixfmt **cc)
 {
-	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
-	const struct imx_media_pixfmt *cc;
 	struct v4l2_mbus_framefmt *infmt;
-	int ret = 0;
-	u32 code;
-
-	if (sdformat->pad >= VDIC_NUM_PADS)
-		return -EINVAL;
-
-	mutex_lock(&priv->lock);
 
-	if (priv->stream_on) {
-		ret = -EBUSY;
-		goto out;
-	}
+	*cc = imx_media_find_ipu_format(sdformat->format.code, CS_SEL_YUV);
+	if (!*cc) {
+		u32 code;
 
-	cc = imx_media_find_ipu_format(sdformat->format.code, CS_SEL_YUV);
-	if (!cc) {
 		imx_media_enum_ipu_format(&code, 0, CS_SEL_YUV);
-		cc = imx_media_find_ipu_format(code, CS_SEL_YUV);
-		sdformat->format.code = cc->codes[0];
+		*cc = imx_media_find_ipu_format(code, CS_SEL_YUV);
+		sdformat->format.code = (*cc)->codes[0];
 	}
 
 	switch (sdformat->pad) {
@@ -609,18 +598,51 @@ static int vdic_set_fmt(struct v4l2_subdev *sd,
 		if (!V4L2_FIELD_HAS_BOTH(sdformat->format.field))
 			sdformat->format.field = V4L2_FIELD_SEQ_TB;
 		break;
-	default:
-		ret = -EINVAL;
+	}
+}
+
+static int vdic_set_fmt(struct v4l2_subdev *sd,
+			struct v4l2_subdev_pad_config *cfg,
+			struct v4l2_subdev_format *sdformat)
+{
+	struct vdic_priv *priv = v4l2_get_subdevdata(sd);
+	const struct imx_media_pixfmt *cc;
+	int ret = 0;
+
+	if (sdformat->pad >= VDIC_NUM_PADS)
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	if (priv->stream_on) {
+		ret = -EBUSY;
 		goto out;
 	}
 
+	vdic_try_fmt(priv, cfg, sdformat, &cc);
+
 	if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
 		cfg->try_fmt = sdformat->format;
-	} else {
-		priv->format_mbus[sdformat->pad] = sdformat->format;
-		priv->cc[sdformat->pad] = cc;
+		goto out;
 	}
 
+	priv->format_mbus[sdformat->pad] = sdformat->format;
+	priv->cc[sdformat->pad] = cc;
+
+	/* propagate format to source pad */
+	if (sdformat->pad == VDIC_SINK_PAD_DIRECT ||
+	    sdformat->pad == VDIC_SINK_PAD_IDMAC) {
+		const struct imx_media_pixfmt *outcc;
+		struct v4l2_subdev_format format;
+
+		format.pad = VDIC_SRC_PAD_DIRECT;
+		format.which = V4L2_SUBDEV_FORMAT_ACTIVE;
+		format.format = sdformat->format;
+		vdic_try_fmt(priv, cfg, &format, &outcc);
+
+		priv->format_mbus[VDIC_SRC_PAD_DIRECT] = format.format;
+		priv->cc[VDIC_SRC_PAD_DIRECT] = outcc;
+	}
 out:
 	mutex_unlock(&priv->lock);
 	return ret;
-- 
2.7.4

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

Version 5 gives me no v4l2 controls exposed through the video device
interface.

Just like with version 4, version 5 is completely useless with IMX219:

imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
ipu1_csi0: pipeline start failed with -110
imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
ipu1_csi0: pipeline start failed with -110
imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
ipu1_csi0: pipeline start failed with -110

So, like v4, I can't do any further testing.

On Thu, Mar 09, 2017 at 08:52:40PM -0800, Steve Longerbeam wrote:
> In version 5:
> 
> - ov5640: renamed "pwdn-gpios" to "powerdown-gpios"
> 
> - ov5640: add mutex lock around the subdev op entry points.
> 
> - ov5640: don't attempt to program the new mode in ov5640_set_fmt().
>   Instead set a new flag, pending_mode_change, and program the new
>   mode at s_stream() if flag is set.
> 
> - ov5640: implement [gs]_frame_interval. As part of that, create
>   ov5640_try_frame_interval(), which is used by both [gs]_frame_interval
>   and [gs]_parm.
> 
> - ov5640: don't attempt to set controls in ov5640_s_ctrl(), or at
>   mode change, do it instead after first power-up.
> 
> - video-multiplexer: include link_validate in media_entity_operations.
> 
> - video-multiplexer: enforce that output pad frame interval must match
>   input pad frame interval in vidsw_s_frame_interval().
> 
> - video-multiplexer: initialize frame interval to a default 30 fps.
> 
> - mipi csi-2: renamed "cfg" clock name property to "ref". This is the
>   27 MHz mipi csi-2 PLL reference clock.
> 
> - mipi csi-2: create a hsfreq_map[] table based on
>   https://community.nxp.com/docs/DOC-94312. Use it to select
>   a hsfreqrange_sel value when programming the D-PHY, based on
>   a max Mbps per lane. This is computed from the source subdev
>   via V4L2_CID_LINK_FREQ control, and if the subdev doesn't implement
>   that control, use a default hard-coded max Mbps per lane.
> 
> - added required ports property description to imx-media binding doc.
> 
> - removed event V4L2_EVENT_FRAME_TIMEOUT. On a frame timeout, which
>   is always unrecoverable, call vb2_queue_error() instead.
> 
> - export the remaining custom events to V4L2_EVENT_FRAME_INTERVAL_ERROR
>   and V4L2_EVENT_NEW_FRAME_BEFORE_EOF.
> 
> - vdic: use V4L2_CID_DEINTERLACING_MODE for motion compensation control
>   instead of a custom control.
> 
> - add v4l2_subdev_link_validate_frame_interval(). Call this in the
>   link_validate imx-media subdev callbacks and video-multiplexer.
> 
> - fix subdev event registration: implementation of subscribe_event()
>   and unsubscribe_event() subdev ops were missing.
> 
> - all calls from the pipeline to the sensor subdev have been removed.
>   Only the CSI subdev still refers to a sensor, and only to retrieve
>   its media bus config, which is necessary to setup the CSI interface.
> 
> - add mutex locks around the imx-media subdev op entry points.
> 
> - completed the propagation of all pad format parameters from sink
>   pads to source pads within every imx-media subdev.
> 
> - implement [gs]_frame_interval in all the imx-media subdevs.
> 
> - imx-ic-prpencvf: there isn't necessarily a CSI subdev in the pipeline
>   in the future, so make sure this is optional when calling the CSI's
>   FIM.
> 
> - the source pads that attach to capture device nodes now require the
>   IPU internal pixel codes. The capture device translates these to
>   v4l2 fourcc memory formats.
> 
> - fix control inheritance to the capture device. When the pipeline
>   was modified, the inherited controls were not being refreshed.
>   v4l2_pipeline_inherit_controls() is now called only in imx-media
>   link_notify() callback when a pipelink link is disabled or modified.
>   imx_media_find_pipeline_video_device() is created to locate the
>   capture device in the pipeline.
> 
> - fix a possible race when propagating formats to the capture device.
>   The subdevs and capture device use different mutex locks when setting
>   formats. imx_media_capture_device_set_format() is created which acquires
>   the capture device mutex when updating the capture device format.
> 
> - verify all subdevs were bound in the async completion callback.
>  
> 
> Philipp Zabel (7):
>   [media] dt-bindings: Add bindings for video-multiplexer device
>   ARM: dts: imx6qdl: Add mipi_ipu1/2 multiplexers, mipi_csi, and their
>     connections
>   add mux and video interface bridge entity functions
>   platform: add video-multiplexer subdevice driver
>   media: imx: csi: fix crop rectangle changes in set_fmt
>   media: imx: csi: add frame skipping support
>   media: imx: csi: fix crop rectangle reset in sink set_fmt
> 
> Russell King (4):
>   media: imx: add support for bayer formats
>   media: imx: csi: add support for bayer formats
>   media: imx: mipi-csi2: enable setting and getting of frame rates
>   media: imx: csi/fim: add support for frame intervals
> 
> Steve Longerbeam (28):
>   [media] dt-bindings: Add bindings for i.MX media driver
>   [media] dt/bindings: Add bindings for OV5640
>   ARM: dts: imx6qdl: Add compatible, clocks, irqs to MIPI CSI-2 node
>   ARM: dts: imx6qdl: add capture-subsystem device
>   ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround
>   ARM: dts: imx6-sabrelite: add OV5642 and OV5640 camera sensors
>   ARM: dts: imx6-sabresd: add OV5642 and OV5640 camera sensors
>   ARM: dts: imx6-sabreauto: create i2cmux for i2c3
>   ARM: dts: imx6-sabreauto: add reset-gpios property for max7310_b
>   ARM: dts: imx6-sabreauto: add pinctrl for gpt input capture
>   ARM: dts: imx6-sabreauto: add the ADV7180 video decoder
>   [media] v4l2: add a frame interval error event
>   [media] v4l2: add a new-frame before end-of-frame event
>   [media] v4l2-mc: add a function to inherit controls from a pipeline
>   [media] v4l: subdev: Add function to validate frame interval
>   [media] add Omnivision OV5640 sensor driver
>   UAPI: Add media UAPI Kbuild file
>   media: Add userspace header file for i.MX
>   media: Add i.MX media core driver
>   media: imx: Add Capture Device Interface
>   media: imx: Add CSI subdev driver
>   media: imx: Add VDIC subdev driver
>   media: imx: Add IC subdev drivers
>   media: imx: Add MIPI CSI-2 Receiver subdev driver
>   ARM: imx_v6_v7_defconfig: Enable staging video4linux drivers
>   media: imx: csi: add __csi_get_fmt
>   media: imx: redo pixel format enumeration and negotiation
>   media: imx: propagate sink pad formats to source pads
> 
>  .../devicetree/bindings/media/i2c/ov5640.txt       |   45 +
>  Documentation/devicetree/bindings/media/imx.txt    |   74 +
>  .../bindings/media/video-multiplexer.txt           |   59 +
>  Documentation/media/uapi/mediactl/media-types.rst  |   22 +
>  Documentation/media/uapi/v4l/vidioc-dqevent.rst    |   12 +
>  Documentation/media/v4l-drivers/imx.rst            |  560 +++++
>  Documentation/media/videodev2.h.rst.exceptions     |    2 +
>  arch/arm/boot/dts/imx6dl-sabrelite.dts             |    5 +
>  arch/arm/boot/dts/imx6dl-sabresd.dts               |    5 +
>  arch/arm/boot/dts/imx6dl.dtsi                      |  185 ++
>  arch/arm/boot/dts/imx6q-sabrelite.dts              |    5 +
>  arch/arm/boot/dts/imx6q-sabresd.dts                |    5 +
>  arch/arm/boot/dts/imx6q.dtsi                       |  121 ++
>  arch/arm/boot/dts/imx6qdl-sabreauto.dtsi           |  144 +-
>  arch/arm/boot/dts/imx6qdl-sabrelite.dtsi           |  152 +-
>  arch/arm/boot/dts/imx6qdl-sabresd.dtsi             |  114 +-
>  arch/arm/boot/dts/imx6qdl.dtsi                     |   17 +-
>  arch/arm/configs/imx_v6_v7_defconfig               |   11 +
>  drivers/media/i2c/Kconfig                          |    7 +
>  drivers/media/i2c/Makefile                         |    1 +
>  drivers/media/i2c/ov5640.c                         | 2231 ++++++++++++++++++++
>  drivers/media/platform/Kconfig                     |    8 +
>  drivers/media/platform/Makefile                    |    2 +
>  drivers/media/platform/video-multiplexer.c         |  498 +++++
>  drivers/media/v4l2-core/v4l2-mc.c                  |   48 +
>  drivers/media/v4l2-core/v4l2-subdev.c              |   50 +
>  drivers/staging/media/Kconfig                      |    2 +
>  drivers/staging/media/Makefile                     |    1 +
>  drivers/staging/media/imx/Kconfig                  |   20 +
>  drivers/staging/media/imx/Makefile                 |   12 +
>  drivers/staging/media/imx/TODO                     |   17 +
>  drivers/staging/media/imx/imx-ic-common.c          |  113 +
>  drivers/staging/media/imx/imx-ic-prp.c             |  497 +++++
>  drivers/staging/media/imx/imx-ic-prpencvf.c        | 1236 +++++++++++
>  drivers/staging/media/imx/imx-ic.h                 |   38 +
>  drivers/staging/media/imx/imx-media-capture.c      |  694 ++++++
>  drivers/staging/media/imx/imx-media-csi.c          | 1595 ++++++++++++++
>  drivers/staging/media/imx/imx-media-dev.c          |  522 +++++
>  drivers/staging/media/imx/imx-media-fim.c          |  463 ++++
>  drivers/staging/media/imx/imx-media-internal-sd.c  |  349 +++
>  drivers/staging/media/imx/imx-media-of.c           |  267 +++
>  drivers/staging/media/imx/imx-media-utils.c        | 1009 +++++++++
>  drivers/staging/media/imx/imx-media-vdic.c         |  949 +++++++++
>  drivers/staging/media/imx/imx-media.h              |  311 +++
>  drivers/staging/media/imx/imx6-mipi-csi2.c         |  725 +++++++
>  include/media/imx.h                                |   15 +
>  include/media/v4l2-mc.h                            |   25 +
>  include/media/v4l2-subdev.h                        |   10 +
>  include/uapi/Kbuild                                |    1 +
>  include/uapi/linux/media.h                         |    6 +
>  include/uapi/linux/v4l2-controls.h                 |    4 +
>  include/uapi/linux/videodev2.h                     |    2 +
>  include/uapi/media/Kbuild                          |    2 +
>  include/uapi/media/imx.h                           |   21 +
>  54 files changed, 13262 insertions(+), 27 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/ov5640.txt
>  create mode 100644 Documentation/devicetree/bindings/media/imx.txt
>  create mode 100644 Documentation/devicetree/bindings/media/video-multiplexer.txt
>  create mode 100644 Documentation/media/v4l-drivers/imx.rst
>  create mode 100644 drivers/media/i2c/ov5640.c
>  create mode 100644 drivers/media/platform/video-multiplexer.c
>  create mode 100644 drivers/staging/media/imx/Kconfig
>  create mode 100644 drivers/staging/media/imx/Makefile
>  create mode 100644 drivers/staging/media/imx/TODO
>  create mode 100644 drivers/staging/media/imx/imx-ic-common.c
>  create mode 100644 drivers/staging/media/imx/imx-ic-prp.c
>  create mode 100644 drivers/staging/media/imx/imx-ic-prpencvf.c
>  create mode 100644 drivers/staging/media/imx/imx-ic.h
>  create mode 100644 drivers/staging/media/imx/imx-media-capture.c
>  create mode 100644 drivers/staging/media/imx/imx-media-csi.c
>  create mode 100644 drivers/staging/media/imx/imx-media-dev.c
>  create mode 100644 drivers/staging/media/imx/imx-media-fim.c
>  create mode 100644 drivers/staging/media/imx/imx-media-internal-sd.c
>  create mode 100644 drivers/staging/media/imx/imx-media-of.c
>  create mode 100644 drivers/staging/media/imx/imx-media-utils.c
>  create mode 100644 drivers/staging/media/imx/imx-media-vdic.c
>  create mode 100644 drivers/staging/media/imx/imx-media.h
>  create mode 100644 drivers/staging/media/imx/imx6-mipi-csi2.c
>  create mode 100644 include/media/imx.h
>  create mode 100644 include/uapi/media/Kbuild
>  create mode 100644 include/uapi/media/imx.h
> 
> -- 
> 2.7.4
> 

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

Version 5 gives me no v4l2 controls exposed through the video device
interface.

Just like with version 4, version 5 is completely useless with IMX219:

imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
ipu1_csi0: pipeline start failed with -110
imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
ipu1_csi0: pipeline start failed with -110
imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
ipu1_csi0: pipeline start failed with -110

So, like v4, I can't do any further testing.

On Thu, Mar 09, 2017 at 08:52:40PM -0800, Steve Longerbeam wrote:
> In version 5:
> 
> - ov5640: renamed "pwdn-gpios" to "powerdown-gpios"
> 
> - ov5640: add mutex lock around the subdev op entry points.
> 
> - ov5640: don't attempt to program the new mode in ov5640_set_fmt().
>   Instead set a new flag, pending_mode_change, and program the new
>   mode at s_stream() if flag is set.
> 
> - ov5640: implement [gs]_frame_interval. As part of that, create
>   ov5640_try_frame_interval(), which is used by both [gs]_frame_interval
>   and [gs]_parm.
> 
> - ov5640: don't attempt to set controls in ov5640_s_ctrl(), or at
>   mode change, do it instead after first power-up.
> 
> - video-multiplexer: include link_validate in media_entity_operations.
> 
> - video-multiplexer: enforce that output pad frame interval must match
>   input pad frame interval in vidsw_s_frame_interval().
> 
> - video-multiplexer: initialize frame interval to a default 30 fps.
> 
> - mipi csi-2: renamed "cfg" clock name property to "ref". This is the
>   27 MHz mipi csi-2 PLL reference clock.
> 
> - mipi csi-2: create a hsfreq_map[] table based on
>   https://community.nxp.com/docs/DOC-94312. Use it to select
>   a hsfreqrange_sel value when programming the D-PHY, based on
>   a max Mbps per lane. This is computed from the source subdev
>   via V4L2_CID_LINK_FREQ control, and if the subdev doesn't implement
>   that control, use a default hard-coded max Mbps per lane.
> 
> - added required ports property description to imx-media binding doc.
> 
> - removed event V4L2_EVENT_FRAME_TIMEOUT. On a frame timeout, which
>   is always unrecoverable, call vb2_queue_error() instead.
> 
> - export the remaining custom events to V4L2_EVENT_FRAME_INTERVAL_ERROR
>   and V4L2_EVENT_NEW_FRAME_BEFORE_EOF.
> 
> - vdic: use V4L2_CID_DEINTERLACING_MODE for motion compensation control
>   instead of a custom control.
> 
> - add v4l2_subdev_link_validate_frame_interval(). Call this in the
>   link_validate imx-media subdev callbacks and video-multiplexer.
> 
> - fix subdev event registration: implementation of subscribe_event()
>   and unsubscribe_event() subdev ops were missing.
> 
> - all calls from the pipeline to the sensor subdev have been removed.
>   Only the CSI subdev still refers to a sensor, and only to retrieve
>   its media bus config, which is necessary to setup the CSI interface.
> 
> - add mutex locks around the imx-media subdev op entry points.
> 
> - completed the propagation of all pad format parameters from sink
>   pads to source pads within every imx-media subdev.
> 
> - implement [gs]_frame_interval in all the imx-media subdevs.
> 
> - imx-ic-prpencvf: there isn't necessarily a CSI subdev in the pipeline
>   in the future, so make sure this is optional when calling the CSI's
>   FIM.
> 
> - the source pads that attach to capture device nodes now require the
>   IPU internal pixel codes. The capture device translates these to
>   v4l2 fourcc memory formats.
> 
> - fix control inheritance to the capture device. When the pipeline
>   was modified, the inherited controls were not being refreshed.
>   v4l2_pipeline_inherit_controls() is now called only in imx-media
>   link_notify() callback when a pipelink link is disabled or modified.
>   imx_media_find_pipeline_video_device() is created to locate the
>   capture device in the pipeline.
> 
> - fix a possible race when propagating formats to the capture device.
>   The subdevs and capture device use different mutex locks when setting
>   formats. imx_media_capture_device_set_format() is created which acquires
>   the capture device mutex when updating the capture device format.
> 
> - verify all subdevs were bound in the async completion callback.
>  
> 
> Philipp Zabel (7):
>   [media] dt-bindings: Add bindings for video-multiplexer device
>   ARM: dts: imx6qdl: Add mipi_ipu1/2 multiplexers, mipi_csi, and their
>     connections
>   add mux and video interface bridge entity functions
>   platform: add video-multiplexer subdevice driver
>   media: imx: csi: fix crop rectangle changes in set_fmt
>   media: imx: csi: add frame skipping support
>   media: imx: csi: fix crop rectangle reset in sink set_fmt
> 
> Russell King (4):
>   media: imx: add support for bayer formats
>   media: imx: csi: add support for bayer formats
>   media: imx: mipi-csi2: enable setting and getting of frame rates
>   media: imx: csi/fim: add support for frame intervals
> 
> Steve Longerbeam (28):
>   [media] dt-bindings: Add bindings for i.MX media driver
>   [media] dt/bindings: Add bindings for OV5640
>   ARM: dts: imx6qdl: Add compatible, clocks, irqs to MIPI CSI-2 node
>   ARM: dts: imx6qdl: add capture-subsystem device
>   ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround
>   ARM: dts: imx6-sabrelite: add OV5642 and OV5640 camera sensors
>   ARM: dts: imx6-sabresd: add OV5642 and OV5640 camera sensors
>   ARM: dts: imx6-sabreauto: create i2cmux for i2c3
>   ARM: dts: imx6-sabreauto: add reset-gpios property for max7310_b
>   ARM: dts: imx6-sabreauto: add pinctrl for gpt input capture
>   ARM: dts: imx6-sabreauto: add the ADV7180 video decoder
>   [media] v4l2: add a frame interval error event
>   [media] v4l2: add a new-frame before end-of-frame event
>   [media] v4l2-mc: add a function to inherit controls from a pipeline
>   [media] v4l: subdev: Add function to validate frame interval
>   [media] add Omnivision OV5640 sensor driver
>   UAPI: Add media UAPI Kbuild file
>   media: Add userspace header file for i.MX
>   media: Add i.MX media core driver
>   media: imx: Add Capture Device Interface
>   media: imx: Add CSI subdev driver
>   media: imx: Add VDIC subdev driver
>   media: imx: Add IC subdev drivers
>   media: imx: Add MIPI CSI-2 Receiver subdev driver
>   ARM: imx_v6_v7_defconfig: Enable staging video4linux drivers
>   media: imx: csi: add __csi_get_fmt
>   media: imx: redo pixel format enumeration and negotiation
>   media: imx: propagate sink pad formats to source pads
> 
>  .../devicetree/bindings/media/i2c/ov5640.txt       |   45 +
>  Documentation/devicetree/bindings/media/imx.txt    |   74 +
>  .../bindings/media/video-multiplexer.txt           |   59 +
>  Documentation/media/uapi/mediactl/media-types.rst  |   22 +
>  Documentation/media/uapi/v4l/vidioc-dqevent.rst    |   12 +
>  Documentation/media/v4l-drivers/imx.rst            |  560 +++++
>  Documentation/media/videodev2.h.rst.exceptions     |    2 +
>  arch/arm/boot/dts/imx6dl-sabrelite.dts             |    5 +
>  arch/arm/boot/dts/imx6dl-sabresd.dts               |    5 +
>  arch/arm/boot/dts/imx6dl.dtsi                      |  185 ++
>  arch/arm/boot/dts/imx6q-sabrelite.dts              |    5 +
>  arch/arm/boot/dts/imx6q-sabresd.dts                |    5 +
>  arch/arm/boot/dts/imx6q.dtsi                       |  121 ++
>  arch/arm/boot/dts/imx6qdl-sabreauto.dtsi           |  144 +-
>  arch/arm/boot/dts/imx6qdl-sabrelite.dtsi           |  152 +-
>  arch/arm/boot/dts/imx6qdl-sabresd.dtsi             |  114 +-
>  arch/arm/boot/dts/imx6qdl.dtsi                     |   17 +-
>  arch/arm/configs/imx_v6_v7_defconfig               |   11 +
>  drivers/media/i2c/Kconfig                          |    7 +
>  drivers/media/i2c/Makefile                         |    1 +
>  drivers/media/i2c/ov5640.c                         | 2231 ++++++++++++++++++++
>  drivers/media/platform/Kconfig                     |    8 +
>  drivers/media/platform/Makefile                    |    2 +
>  drivers/media/platform/video-multiplexer.c         |  498 +++++
>  drivers/media/v4l2-core/v4l2-mc.c                  |   48 +
>  drivers/media/v4l2-core/v4l2-subdev.c              |   50 +
>  drivers/staging/media/Kconfig                      |    2 +
>  drivers/staging/media/Makefile                     |    1 +
>  drivers/staging/media/imx/Kconfig                  |   20 +
>  drivers/staging/media/imx/Makefile                 |   12 +
>  drivers/staging/media/imx/TODO                     |   17 +
>  drivers/staging/media/imx/imx-ic-common.c          |  113 +
>  drivers/staging/media/imx/imx-ic-prp.c             |  497 +++++
>  drivers/staging/media/imx/imx-ic-prpencvf.c        | 1236 +++++++++++
>  drivers/staging/media/imx/imx-ic.h                 |   38 +
>  drivers/staging/media/imx/imx-media-capture.c      |  694 ++++++
>  drivers/staging/media/imx/imx-media-csi.c          | 1595 ++++++++++++++
>  drivers/staging/media/imx/imx-media-dev.c          |  522 +++++
>  drivers/staging/media/imx/imx-media-fim.c          |  463 ++++
>  drivers/staging/media/imx/imx-media-internal-sd.c  |  349 +++
>  drivers/staging/media/imx/imx-media-of.c           |  267 +++
>  drivers/staging/media/imx/imx-media-utils.c        | 1009 +++++++++
>  drivers/staging/media/imx/imx-media-vdic.c         |  949 +++++++++
>  drivers/staging/media/imx/imx-media.h              |  311 +++
>  drivers/staging/media/imx/imx6-mipi-csi2.c         |  725 +++++++
>  include/media/imx.h                                |   15 +
>  include/media/v4l2-mc.h                            |   25 +
>  include/media/v4l2-subdev.h                        |   10 +
>  include/uapi/Kbuild                                |    1 +
>  include/uapi/linux/media.h                         |    6 +
>  include/uapi/linux/v4l2-controls.h                 |    4 +
>  include/uapi/linux/videodev2.h                     |    2 +
>  include/uapi/media/Kbuild                          |    2 +
>  include/uapi/media/imx.h                           |   21 +
>  54 files changed, 13262 insertions(+), 27 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/ov5640.txt
>  create mode 100644 Documentation/devicetree/bindings/media/imx.txt
>  create mode 100644 Documentation/devicetree/bindings/media/video-multiplexer.txt
>  create mode 100644 Documentation/media/v4l-drivers/imx.rst
>  create mode 100644 drivers/media/i2c/ov5640.c
>  create mode 100644 drivers/media/platform/video-multiplexer.c
>  create mode 100644 drivers/staging/media/imx/Kconfig
>  create mode 100644 drivers/staging/media/imx/Makefile
>  create mode 100644 drivers/staging/media/imx/TODO
>  create mode 100644 drivers/staging/media/imx/imx-ic-common.c
>  create mode 100644 drivers/staging/media/imx/imx-ic-prp.c
>  create mode 100644 drivers/staging/media/imx/imx-ic-prpencvf.c
>  create mode 100644 drivers/staging/media/imx/imx-ic.h
>  create mode 100644 drivers/staging/media/imx/imx-media-capture.c
>  create mode 100644 drivers/staging/media/imx/imx-media-csi.c
>  create mode 100644 drivers/staging/media/imx/imx-media-dev.c
>  create mode 100644 drivers/staging/media/imx/imx-media-fim.c
>  create mode 100644 drivers/staging/media/imx/imx-media-internal-sd.c
>  create mode 100644 drivers/staging/media/imx/imx-media-of.c
>  create mode 100644 drivers/staging/media/imx/imx-media-utils.c
>  create mode 100644 drivers/staging/media/imx/imx-media-vdic.c
>  create mode 100644 drivers/staging/media/imx/imx-media.h
>  create mode 100644 drivers/staging/media/imx/imx6-mipi-csi2.c
>  create mode 100644 include/media/imx.h
>  create mode 100644 include/uapi/media/Kbuild
>  create mode 100644 include/uapi/media/imx.h
> 
> -- 
> 2.7.4
> 

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

Version 5 gives me no v4l2 controls exposed through the video device
interface.

Just like with version 4, version 5 is completely useless with IMX219:

imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
ipu1_csi0: pipeline start failed with -110
imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
ipu1_csi0: pipeline start failed with -110
imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
ipu1_csi0: pipeline start failed with -110

So, like v4, I can't do any further testing.

On Thu, Mar 09, 2017 at 08:52:40PM -0800, Steve Longerbeam wrote:
> In version 5:
> 
> - ov5640: renamed "pwdn-gpios" to "powerdown-gpios"
> 
> - ov5640: add mutex lock around the subdev op entry points.
> 
> - ov5640: don't attempt to program the new mode in ov5640_set_fmt().
>   Instead set a new flag, pending_mode_change, and program the new
>   mode at s_stream() if flag is set.
> 
> - ov5640: implement [gs]_frame_interval. As part of that, create
>   ov5640_try_frame_interval(), which is used by both [gs]_frame_interval
>   and [gs]_parm.
> 
> - ov5640: don't attempt to set controls in ov5640_s_ctrl(), or at
>   mode change, do it instead after first power-up.
> 
> - video-multiplexer: include link_validate in media_entity_operations.
> 
> - video-multiplexer: enforce that output pad frame interval must match
>   input pad frame interval in vidsw_s_frame_interval().
> 
> - video-multiplexer: initialize frame interval to a default 30 fps.
> 
> - mipi csi-2: renamed "cfg" clock name property to "ref". This is the
>   27 MHz mipi csi-2 PLL reference clock.
> 
> - mipi csi-2: create a hsfreq_map[] table based on
>   https://community.nxp.com/docs/DOC-94312. Use it to select
>   a hsfreqrange_sel value when programming the D-PHY, based on
>   a max Mbps per lane. This is computed from the source subdev
>   via V4L2_CID_LINK_FREQ control, and if the subdev doesn't implement
>   that control, use a default hard-coded max Mbps per lane.
> 
> - added required ports property description to imx-media binding doc.
> 
> - removed event V4L2_EVENT_FRAME_TIMEOUT. On a frame timeout, which
>   is always unrecoverable, call vb2_queue_error() instead.
> 
> - export the remaining custom events to V4L2_EVENT_FRAME_INTERVAL_ERROR
>   and V4L2_EVENT_NEW_FRAME_BEFORE_EOF.
> 
> - vdic: use V4L2_CID_DEINTERLACING_MODE for motion compensation control
>   instead of a custom control.
> 
> - add v4l2_subdev_link_validate_frame_interval(). Call this in the
>   link_validate imx-media subdev callbacks and video-multiplexer.
> 
> - fix subdev event registration: implementation of subscribe_event()
>   and unsubscribe_event() subdev ops were missing.
> 
> - all calls from the pipeline to the sensor subdev have been removed.
>   Only the CSI subdev still refers to a sensor, and only to retrieve
>   its media bus config, which is necessary to setup the CSI interface.
> 
> - add mutex locks around the imx-media subdev op entry points.
> 
> - completed the propagation of all pad format parameters from sink
>   pads to source pads within every imx-media subdev.
> 
> - implement [gs]_frame_interval in all the imx-media subdevs.
> 
> - imx-ic-prpencvf: there isn't necessarily a CSI subdev in the pipeline
>   in the future, so make sure this is optional when calling the CSI's
>   FIM.
> 
> - the source pads that attach to capture device nodes now require the
>   IPU internal pixel codes. The capture device translates these to
>   v4l2 fourcc memory formats.
> 
> - fix control inheritance to the capture device. When the pipeline
>   was modified, the inherited controls were not being refreshed.
>   v4l2_pipeline_inherit_controls() is now called only in imx-media
>   link_notify() callback when a pipelink link is disabled or modified.
>   imx_media_find_pipeline_video_device() is created to locate the
>   capture device in the pipeline.
> 
> - fix a possible race when propagating formats to the capture device.
>   The subdevs and capture device use different mutex locks when setting
>   formats. imx_media_capture_device_set_format() is created which acquires
>   the capture device mutex when updating the capture device format.
> 
> - verify all subdevs were bound in the async completion callback.
>  
> 
> Philipp Zabel (7):
>   [media] dt-bindings: Add bindings for video-multiplexer device
>   ARM: dts: imx6qdl: Add mipi_ipu1/2 multiplexers, mipi_csi, and their
>     connections
>   add mux and video interface bridge entity functions
>   platform: add video-multiplexer subdevice driver
>   media: imx: csi: fix crop rectangle changes in set_fmt
>   media: imx: csi: add frame skipping support
>   media: imx: csi: fix crop rectangle reset in sink set_fmt
> 
> Russell King (4):
>   media: imx: add support for bayer formats
>   media: imx: csi: add support for bayer formats
>   media: imx: mipi-csi2: enable setting and getting of frame rates
>   media: imx: csi/fim: add support for frame intervals
> 
> Steve Longerbeam (28):
>   [media] dt-bindings: Add bindings for i.MX media driver
>   [media] dt/bindings: Add bindings for OV5640
>   ARM: dts: imx6qdl: Add compatible, clocks, irqs to MIPI CSI-2 node
>   ARM: dts: imx6qdl: add capture-subsystem device
>   ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround
>   ARM: dts: imx6-sabrelite: add OV5642 and OV5640 camera sensors
>   ARM: dts: imx6-sabresd: add OV5642 and OV5640 camera sensors
>   ARM: dts: imx6-sabreauto: create i2cmux for i2c3
>   ARM: dts: imx6-sabreauto: add reset-gpios property for max7310_b
>   ARM: dts: imx6-sabreauto: add pinctrl for gpt input capture
>   ARM: dts: imx6-sabreauto: add the ADV7180 video decoder
>   [media] v4l2: add a frame interval error event
>   [media] v4l2: add a new-frame before end-of-frame event
>   [media] v4l2-mc: add a function to inherit controls from a pipeline
>   [media] v4l: subdev: Add function to validate frame interval
>   [media] add Omnivision OV5640 sensor driver
>   UAPI: Add media UAPI Kbuild file
>   media: Add userspace header file for i.MX
>   media: Add i.MX media core driver
>   media: imx: Add Capture Device Interface
>   media: imx: Add CSI subdev driver
>   media: imx: Add VDIC subdev driver
>   media: imx: Add IC subdev drivers
>   media: imx: Add MIPI CSI-2 Receiver subdev driver
>   ARM: imx_v6_v7_defconfig: Enable staging video4linux drivers
>   media: imx: csi: add __csi_get_fmt
>   media: imx: redo pixel format enumeration and negotiation
>   media: imx: propagate sink pad formats to source pads
> 
>  .../devicetree/bindings/media/i2c/ov5640.txt       |   45 +
>  Documentation/devicetree/bindings/media/imx.txt    |   74 +
>  .../bindings/media/video-multiplexer.txt           |   59 +
>  Documentation/media/uapi/mediactl/media-types.rst  |   22 +
>  Documentation/media/uapi/v4l/vidioc-dqevent.rst    |   12 +
>  Documentation/media/v4l-drivers/imx.rst            |  560 +++++
>  Documentation/media/videodev2.h.rst.exceptions     |    2 +
>  arch/arm/boot/dts/imx6dl-sabrelite.dts             |    5 +
>  arch/arm/boot/dts/imx6dl-sabresd.dts               |    5 +
>  arch/arm/boot/dts/imx6dl.dtsi                      |  185 ++
>  arch/arm/boot/dts/imx6q-sabrelite.dts              |    5 +
>  arch/arm/boot/dts/imx6q-sabresd.dts                |    5 +
>  arch/arm/boot/dts/imx6q.dtsi                       |  121 ++
>  arch/arm/boot/dts/imx6qdl-sabreauto.dtsi           |  144 +-
>  arch/arm/boot/dts/imx6qdl-sabrelite.dtsi           |  152 +-
>  arch/arm/boot/dts/imx6qdl-sabresd.dtsi             |  114 +-
>  arch/arm/boot/dts/imx6qdl.dtsi                     |   17 +-
>  arch/arm/configs/imx_v6_v7_defconfig               |   11 +
>  drivers/media/i2c/Kconfig                          |    7 +
>  drivers/media/i2c/Makefile                         |    1 +
>  drivers/media/i2c/ov5640.c                         | 2231 ++++++++++++++++++++
>  drivers/media/platform/Kconfig                     |    8 +
>  drivers/media/platform/Makefile                    |    2 +
>  drivers/media/platform/video-multiplexer.c         |  498 +++++
>  drivers/media/v4l2-core/v4l2-mc.c                  |   48 +
>  drivers/media/v4l2-core/v4l2-subdev.c              |   50 +
>  drivers/staging/media/Kconfig                      |    2 +
>  drivers/staging/media/Makefile                     |    1 +
>  drivers/staging/media/imx/Kconfig                  |   20 +
>  drivers/staging/media/imx/Makefile                 |   12 +
>  drivers/staging/media/imx/TODO                     |   17 +
>  drivers/staging/media/imx/imx-ic-common.c          |  113 +
>  drivers/staging/media/imx/imx-ic-prp.c             |  497 +++++
>  drivers/staging/media/imx/imx-ic-prpencvf.c        | 1236 +++++++++++
>  drivers/staging/media/imx/imx-ic.h                 |   38 +
>  drivers/staging/media/imx/imx-media-capture.c      |  694 ++++++
>  drivers/staging/media/imx/imx-media-csi.c          | 1595 ++++++++++++++
>  drivers/staging/media/imx/imx-media-dev.c          |  522 +++++
>  drivers/staging/media/imx/imx-media-fim.c          |  463 ++++
>  drivers/staging/media/imx/imx-media-internal-sd.c  |  349 +++
>  drivers/staging/media/imx/imx-media-of.c           |  267 +++
>  drivers/staging/media/imx/imx-media-utils.c        | 1009 +++++++++
>  drivers/staging/media/imx/imx-media-vdic.c         |  949 +++++++++
>  drivers/staging/media/imx/imx-media.h              |  311 +++
>  drivers/staging/media/imx/imx6-mipi-csi2.c         |  725 +++++++
>  include/media/imx.h                                |   15 +
>  include/media/v4l2-mc.h                            |   25 +
>  include/media/v4l2-subdev.h                        |   10 +
>  include/uapi/Kbuild                                |    1 +
>  include/uapi/linux/media.h                         |    6 +
>  include/uapi/linux/v4l2-controls.h                 |    4 +
>  include/uapi/linux/videodev2.h                     |    2 +
>  include/uapi/media/Kbuild                          |    2 +
>  include/uapi/media/imx.h                           |   21 +
>  54 files changed, 13262 insertions(+), 27 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/ov5640.txt
>  create mode 100644 Documentation/devicetree/bindings/media/imx.txt
>  create mode 100644 Documentation/devicetree/bindings/media/video-multiplexer.txt
>  create mode 100644 Documentation/media/v4l-drivers/imx.rst
>  create mode 100644 drivers/media/i2c/ov5640.c
>  create mode 100644 drivers/media/platform/video-multiplexer.c
>  create mode 100644 drivers/staging/media/imx/Kconfig
>  create mode 100644 drivers/staging/media/imx/Makefile
>  create mode 100644 drivers/staging/media/imx/TODO
>  create mode 100644 drivers/staging/media/imx/imx-ic-common.c
>  create mode 100644 drivers/staging/media/imx/imx-ic-prp.c
>  create mode 100644 drivers/staging/media/imx/imx-ic-prpencvf.c
>  create mode 100644 drivers/staging/media/imx/imx-ic.h
>  create mode 100644 drivers/staging/media/imx/imx-media-capture.c
>  create mode 100644 drivers/staging/media/imx/imx-media-csi.c
>  create mode 100644 drivers/staging/media/imx/imx-media-dev.c
>  create mode 100644 drivers/staging/media/imx/imx-media-fim.c
>  create mode 100644 drivers/staging/media/imx/imx-media-internal-sd.c
>  create mode 100644 drivers/staging/media/imx/imx-media-of.c
>  create mode 100644 drivers/staging/media/imx/imx-media-utils.c
>  create mode 100644 drivers/staging/media/imx/imx-media-vdic.c
>  create mode 100644 drivers/staging/media/imx/imx-media.h
>  create mode 100644 drivers/staging/media/imx/imx6-mipi-csi2.c
>  create mode 100644 include/media/imx.h
>  create mode 100644 include/uapi/media/Kbuild
>  create mode 100644 include/uapi/media/imx.h
> 
> -- 
> 2.7.4
> 

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/10/2017 12:13 PM, Russell King - ARM Linux wrote:
> Version 5 gives me no v4l2 controls exposed through the video device
> interface.
>
> Just like with version 4, version 5 is completely useless with IMX219:
>
> imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> ipu1_csi0: pipeline start failed with -110
> imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> ipu1_csi0: pipeline start failed with -110
> imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> ipu1_csi0: pipeline start failed with -110
>
> So, like v4, I can't do any further testing.
>

Is the imx219 placing the csi-2 bus in LP-11 state on exit
from s_power(ON)?

I realize that probably means bringing the chip up to a
completely operational state and then setting it to stream
OFF in the s_power() op.

The same had to be done for the OV5640.

Steve

[PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/10/2017 12:13 PM, Russell King - ARM Linux wrote:
> Version 5 gives me no v4l2 controls exposed through the video device
> interface.
>
> Just like with version 4, version 5 is completely useless with IMX219:
>
> imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> ipu1_csi0: pipeline start failed with -110
> imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> ipu1_csi0: pipeline start failed with -110
> imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> ipu1_csi0: pipeline start failed with -110
>
> So, like v4, I can't do any further testing.
>

Is the imx219 placing the csi-2 bus in LP-11 state on exit
from s_power(ON)?

I realize that probably means bringing the chip up to a
completely operational state and then setting it to stream
OFF in the s_power() op.

The same had to be done for the OV5640.

Steve

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/10/2017 12:13 PM, Russell King - ARM Linux wrote:
> Version 5 gives me no v4l2 controls exposed through the video device
> interface.
>
> Just like with version 4, version 5 is completely useless with IMX219:
>
> imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> ipu1_csi0: pipeline start failed with -110
> imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> ipu1_csi0: pipeline start failed with -110
> imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> ipu1_csi0: pipeline start failed with -110
>
> So, like v4, I can't do any further testing.
>

Is the imx219 placing the csi-2 bus in LP-11 state on exit
from s_power(ON)?

I realize that probably means bringing the chip up to a
completely operational state and then setting it to stream
OFF in the s_power() op.

The same had to be done for the OV5640.

Steve

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Fri, Mar 10, 2017 at 03:20:34PM -0800, Steve Longerbeam wrote:
> 
> 
> On 03/10/2017 12:13 PM, Russell King - ARM Linux wrote:
> >Version 5 gives me no v4l2 controls exposed through the video device
> >interface.
> >
> >Just like with version 4, version 5 is completely useless with IMX219:
> >
> >imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> >ipu1_csi0: pipeline start failed with -110
> >imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> >ipu1_csi0: pipeline start failed with -110
> >imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> >ipu1_csi0: pipeline start failed with -110
> >
> >So, like v4, I can't do any further testing.
> >
> 
> Is the imx219 placing the csi-2 bus in LP-11 state on exit
> from s_power(ON)?
> 
> I realize that probably means bringing the chip up to a
> completely operational state and then setting it to stream
> OFF in the s_power() op.
> 
> The same had to be done for the OV5640.

What do you suggest - setting it to the highest CSI2 bus speed that
it supports?  That's likely to be over the maximum data rate specified
for iMX6Q if it's wired up using four lanes.


Also, as I've already said, I think that powering on the sensor just
because it's got an enabled media-controller link is a silly idea.

Right now, the only way of using the imx6 capture stuff is to manually
configure it with media-ctl, which means that happens either at boot
due to a custom boot script, or when you first use it (by manually
running a script.)

This results in the sensor staying powered from that point onwards,
wasting power unnecessarily.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Fri, Mar 10, 2017 at 03:20:34PM -0800, Steve Longerbeam wrote:
> 
> 
> On 03/10/2017 12:13 PM, Russell King - ARM Linux wrote:
> >Version 5 gives me no v4l2 controls exposed through the video device
> >interface.
> >
> >Just like with version 4, version 5 is completely useless with IMX219:
> >
> >imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> >ipu1_csi0: pipeline start failed with -110
> >imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> >ipu1_csi0: pipeline start failed with -110
> >imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> >ipu1_csi0: pipeline start failed with -110
> >
> >So, like v4, I can't do any further testing.
> >
> 
> Is the imx219 placing the csi-2 bus in LP-11 state on exit
> from s_power(ON)?
> 
> I realize that probably means bringing the chip up to a
> completely operational state and then setting it to stream
> OFF in the s_power() op.
> 
> The same had to be done for the OV5640.

What do you suggest - setting it to the highest CSI2 bus speed that
it supports?  That's likely to be over the maximum data rate specified
for iMX6Q if it's wired up using four lanes.


Also, as I've already said, I think that powering on the sensor just
because it's got an enabled media-controller link is a silly idea.

Right now, the only way of using the imx6 capture stuff is to manually
configure it with media-ctl, which means that happens either at boot
due to a custom boot script, or when you first use it (by manually
running a script.)

This results in the sensor staying powered from that point onwards,
wasting power unnecessarily.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Fri, Mar 10, 2017 at 03:20:34PM -0800, Steve Longerbeam wrote:
> 
> 
> On 03/10/2017 12:13 PM, Russell King - ARM Linux wrote:
> >Version 5 gives me no v4l2 controls exposed through the video device
> >interface.
> >
> >Just like with version 4, version 5 is completely useless with IMX219:
> >
> >imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> >ipu1_csi0: pipeline start failed with -110
> >imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> >ipu1_csi0: pipeline start failed with -110
> >imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> >ipu1_csi0: pipeline start failed with -110
> >
> >So, like v4, I can't do any further testing.
> >
> 
> Is the imx219 placing the csi-2 bus in LP-11 state on exit
> from s_power(ON)?
> 
> I realize that probably means bringing the chip up to a
> completely operational state and then setting it to stream
> OFF in the s_power() op.
> 
> The same had to be done for the OV5640.

What do you suggest - setting it to the highest CSI2 bus speed that
it supports?  That's likely to be over the maximum data rate specified
for iMX6Q if it's wired up using four lanes.


Also, as I've already said, I think that powering on the sensor just
because it's got an enabled media-controller link is a silly idea.

Right now, the only way of using the imx6 capture stuff is to manually
configure it with media-ctl, which means that happens either at boot
due to a custom boot script, or when you first use it (by manually
running a script.)

This results in the sensor staying powered from that point onwards,
wasting power unnecessarily.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

[-- Attachment #1: Type: text/plain, Size: 904 bytes --]



On 03/10/2017 12:13 PM, Russell King - ARM Linux wrote:
> Version 5 gives me no v4l2 controls exposed through the video device
> interface.
>
> Just like with version 4, version 5 is completely useless with IMX219:
>
> imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> ipu1_csi0: pipeline start failed with -110
> imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> ipu1_csi0: pipeline start failed with -110
> imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> ipu1_csi0: pipeline start failed with -110
>

If it's too difficult to get the imx219 csi-2 transmitter into the
LP-11 state on power on, perhaps the csi-2 receiver can be a little
more lenient on the transmitter and make the LP-11 timeout a warning
instead of error-out.

Can you try the attached change on top of the version 5 patchset?

If that doesn't work then you're just going to have to fix the bug
in imx219.

Steve

[-- Attachment #2: warn-on-lp-11-timeout.diff --]
[-- Type: text/x-patch, Size: 611 bytes --]

diff --git a/drivers/staging/media/imx/imx6-mipi-csi2.c b/drivers/staging/media/imx/imx6-mipi-csi2.c
index d8f931e..720bf4d 100644
--- a/drivers/staging/media/imx/imx6-mipi-csi2.c
+++ b/drivers/staging/media/imx/imx6-mipi-csi2.c
@@ -224,11 +224,8 @@ static int csi2_dphy_wait_stopstate(struct csi2_dev *csi2)
 
 	ret = readl_poll_timeout(csi2->base + CSI2_PHY_STATE, reg,
 				 (reg & mask) == mask, 0, 500000);
-	if (ret) {
-		v4l2_err(&csi2->sd, "LP-11 timeout, phy_state = 0x%08x\n", reg);
-		return ret;
-	}
-
+	if (ret)
+		v4l2_warn(&csi2->sd, "LP-11 timeout, phy_state = 0x%08x\n", reg);
 	return 0;
 }
 

[PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/10/2017 12:13 PM, Russell King - ARM Linux wrote:
> Version 5 gives me no v4l2 controls exposed through the video device
> interface.
>
> Just like with version 4, version 5 is completely useless with IMX219:
>
> imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> ipu1_csi0: pipeline start failed with -110
> imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> ipu1_csi0: pipeline start failed with -110
> imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> ipu1_csi0: pipeline start failed with -110
>

If it's too difficult to get the imx219 csi-2 transmitter into the
LP-11 state on power on, perhaps the csi-2 receiver can be a little
more lenient on the transmitter and make the LP-11 timeout a warning
instead of error-out.

Can you try the attached change on top of the version 5 patchset?

If that doesn't work then you're just going to have to fix the bug
in imx219.

Steve
-------------- next part --------------
A non-text attachment was scrubbed...
Name: warn-on-lp-11-timeout.diff
Type: text/x-patch
Size: 611 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170311/3b438f44/attachment.bin>

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

[-- Attachment #1: Type: text/plain, Size: 904 bytes --]



On 03/10/2017 12:13 PM, Russell King - ARM Linux wrote:
> Version 5 gives me no v4l2 controls exposed through the video device
> interface.
>
> Just like with version 4, version 5 is completely useless with IMX219:
>
> imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> ipu1_csi0: pipeline start failed with -110
> imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> ipu1_csi0: pipeline start failed with -110
> imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> ipu1_csi0: pipeline start failed with -110
>

If it's too difficult to get the imx219 csi-2 transmitter into the
LP-11 state on power on, perhaps the csi-2 receiver can be a little
more lenient on the transmitter and make the LP-11 timeout a warning
instead of error-out.

Can you try the attached change on top of the version 5 patchset?

If that doesn't work then you're just going to have to fix the bug
in imx219.

Steve

[-- Attachment #2: warn-on-lp-11-timeout.diff --]
[-- Type: text/x-patch, Size: 611 bytes --]

diff --git a/drivers/staging/media/imx/imx6-mipi-csi2.c b/drivers/staging/media/imx/imx6-mipi-csi2.c
index d8f931e..720bf4d 100644
--- a/drivers/staging/media/imx/imx6-mipi-csi2.c
+++ b/drivers/staging/media/imx/imx6-mipi-csi2.c
@@ -224,11 +224,8 @@ static int csi2_dphy_wait_stopstate(struct csi2_dev *csi2)
 
 	ret = readl_poll_timeout(csi2->base + CSI2_PHY_STATE, reg,
 				 (reg & mask) == mask, 0, 500000);
-	if (ret) {
-		v4l2_err(&csi2->sd, "LP-11 timeout, phy_state = 0x%08x\n", reg);
-		return ret;
-	}
-
+	if (ret)
+		v4l2_warn(&csi2->sd, "LP-11 timeout, phy_state = 0x%08x\n", reg);
 	return 0;
 }
 

[-- Attachment #3: Type: text/plain, Size: 169 bytes --]

_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sat, Mar 11, 2017 at 04:30:53PM -0800, Steve Longerbeam wrote:
> If it's too difficult to get the imx219 csi-2 transmitter into the
> LP-11 state on power on, perhaps the csi-2 receiver can be a little
> more lenient on the transmitter and make the LP-11 timeout a warning
> instead of error-out.
> 
> Can you try the attached change on top of the version 5 patchset?
> 
> If that doesn't work then you're just going to have to fix the bug
> in imx219.

That patch gets me past that hurdle, only to reveal that there's another
issue:

imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
imx219 0-0010: VT: pixclk 139200000Hz line 80742Hz frame 30.0Hz
imx219 0-0010: VT: line period 12385ns
imx219 0-0010: OP: pixclk 38500000Hz, 2 lanes, 308Mbps peak each
imx219 0-0010: OP: 3288 bits/line/lane act=10675ns lp/idle=1710ns
ipu1_csi0: csi_idmac_setup failed: -22
ipu1_csi0: pipeline start failed with -22
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1860 at /home/rmk/git/linux-rmk/drivers/media/v4l2-core/videobuf2-core.c:1340 vb2_start_streaming+0x124/0x1b4 [videobuf2_core]

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sat, Mar 11, 2017 at 04:30:53PM -0800, Steve Longerbeam wrote:
> If it's too difficult to get the imx219 csi-2 transmitter into the
> LP-11 state on power on, perhaps the csi-2 receiver can be a little
> more lenient on the transmitter and make the LP-11 timeout a warning
> instead of error-out.
> 
> Can you try the attached change on top of the version 5 patchset?
> 
> If that doesn't work then you're just going to have to fix the bug
> in imx219.

That patch gets me past that hurdle, only to reveal that there's another
issue:

imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
imx219 0-0010: VT: pixclk 139200000Hz line 80742Hz frame 30.0Hz
imx219 0-0010: VT: line period 12385ns
imx219 0-0010: OP: pixclk 38500000Hz, 2 lanes, 308Mbps peak each
imx219 0-0010: OP: 3288 bits/line/lane act=10675ns lp/idle=1710ns
ipu1_csi0: csi_idmac_setup failed: -22
ipu1_csi0: pipeline start failed with -22
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1860 at /home/rmk/git/linux-rmk/drivers/media/v4l2-core/videobuf2-core.c:1340 vb2_start_streaming+0x124/0x1b4 [videobuf2_core]

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sat, Mar 11, 2017 at 04:30:53PM -0800, Steve Longerbeam wrote:
> If it's too difficult to get the imx219 csi-2 transmitter into the
> LP-11 state on power on, perhaps the csi-2 receiver can be a little
> more lenient on the transmitter and make the LP-11 timeout a warning
> instead of error-out.
> 
> Can you try the attached change on top of the version 5 patchset?
> 
> If that doesn't work then you're just going to have to fix the bug
> in imx219.

That patch gets me past that hurdle, only to reveal that there's another
issue:

imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
imx219 0-0010: VT: pixclk 139200000Hz line 80742Hz frame 30.0Hz
imx219 0-0010: VT: line period 12385ns
imx219 0-0010: OP: pixclk 38500000Hz, 2 lanes, 308Mbps peak each
imx219 0-0010: OP: 3288 bits/line/lane act=10675ns lp/idle=1710ns
ipu1_csi0: csi_idmac_setup failed: -22
ipu1_csi0: pipeline start failed with -22
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1860 at /home/rmk/git/linux-rmk/drivers/media/v4l2-core/videobuf2-core.c:1340 vb2_start_streaming+0x124/0x1b4 [videobuf2_core]

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 12:57 PM, Russell King - ARM Linux wrote:
> On Sat, Mar 11, 2017 at 04:30:53PM -0800, Steve Longerbeam wrote:
>> If it's too difficult to get the imx219 csi-2 transmitter into the
>> LP-11 state on power on, perhaps the csi-2 receiver can be a little
>> more lenient on the transmitter and make the LP-11 timeout a warning
>> instead of error-out.
>>
>> Can you try the attached change on top of the version 5 patchset?
>>
>> If that doesn't work then you're just going to have to fix the bug
>> in imx219.
>
> That patch gets me past that hurdle, only to reveal that there's another
> issue:

Yeah, ipu_cpmem_set_image() failed because it doesn't recognize the
bayer formats. Wait, didn't we fix this already? I've lost track.
Ah, right, we were going to move this support into the IPUv3 driver,
but in the meantime I think you had some patches to get around this.

Steve


>
> imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> imx219 0-0010: VT: pixclk 139200000Hz line 80742Hz frame 30.0Hz
> imx219 0-0010: VT: line period 12385ns
> imx219 0-0010: OP: pixclk 38500000Hz, 2 lanes, 308Mbps peak each
> imx219 0-0010: OP: 3288 bits/line/lane act=10675ns lp/idle=1710ns
> ipu1_csi0: csi_idmac_setup failed: -22
> ipu1_csi0: pipeline start failed with -22
> ------------[ cut here ]------------
> WARNING: CPU: 0 PID: 1860 at /home/rmk/git/linux-rmk/drivers/media/v4l2-core/videobuf2-core.c:1340 vb2_start_streaming+0x124/0x1b4 [videobuf2_core]
>

[PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 12:57 PM, Russell King - ARM Linux wrote:
> On Sat, Mar 11, 2017 at 04:30:53PM -0800, Steve Longerbeam wrote:
>> If it's too difficult to get the imx219 csi-2 transmitter into the
>> LP-11 state on power on, perhaps the csi-2 receiver can be a little
>> more lenient on the transmitter and make the LP-11 timeout a warning
>> instead of error-out.
>>
>> Can you try the attached change on top of the version 5 patchset?
>>
>> If that doesn't work then you're just going to have to fix the bug
>> in imx219.
>
> That patch gets me past that hurdle, only to reveal that there's another
> issue:

Yeah, ipu_cpmem_set_image() failed because it doesn't recognize the
bayer formats. Wait, didn't we fix this already? I've lost track.
Ah, right, we were going to move this support into the IPUv3 driver,
but in the meantime I think you had some patches to get around this.

Steve


>
> imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> imx219 0-0010: VT: pixclk 139200000Hz line 80742Hz frame 30.0Hz
> imx219 0-0010: VT: line period 12385ns
> imx219 0-0010: OP: pixclk 38500000Hz, 2 lanes, 308Mbps peak each
> imx219 0-0010: OP: 3288 bits/line/lane act=10675ns lp/idle=1710ns
> ipu1_csi0: csi_idmac_setup failed: -22
> ipu1_csi0: pipeline start failed with -22
> ------------[ cut here ]------------
> WARNING: CPU: 0 PID: 1860 at /home/rmk/git/linux-rmk/drivers/media/v4l2-core/videobuf2-core.c:1340 vb2_start_streaming+0x124/0x1b4 [videobuf2_core]
>

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 12:57 PM, Russell King - ARM Linux wrote:
> On Sat, Mar 11, 2017 at 04:30:53PM -0800, Steve Longerbeam wrote:
>> If it's too difficult to get the imx219 csi-2 transmitter into the
>> LP-11 state on power on, perhaps the csi-2 receiver can be a little
>> more lenient on the transmitter and make the LP-11 timeout a warning
>> instead of error-out.
>>
>> Can you try the attached change on top of the version 5 patchset?
>>
>> If that doesn't work then you're just going to have to fix the bug
>> in imx219.
>
> That patch gets me past that hurdle, only to reveal that there's another
> issue:

Yeah, ipu_cpmem_set_image() failed because it doesn't recognize the
bayer formats. Wait, didn't we fix this already? I've lost track.
Ah, right, we were going to move this support into the IPUv3 driver,
but in the meantime I think you had some patches to get around this.

Steve


>
> imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000200
> imx219 0-0010: VT: pixclk 139200000Hz line 80742Hz frame 30.0Hz
> imx219 0-0010: VT: line period 12385ns
> imx219 0-0010: OP: pixclk 38500000Hz, 2 lanes, 308Mbps peak each
> imx219 0-0010: OP: 3288 bits/line/lane act=10675ns lp/idle=1710ns
> ipu1_csi0: csi_idmac_setup failed: -22
> ipu1_csi0: pipeline start failed with -22
> ------------[ cut here ]------------
> WARNING: CPU: 0 PID: 1860 at /home/rmk/git/linux-rmk/drivers/media/v4l2-core/videobuf2-core.c:1340 vb2_start_streaming+0x124/0x1b4 [videobuf2_core]
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 12, 2017 at 01:05:06PM -0700, Steve Longerbeam wrote:
> 
> 
> On 03/12/2017 12:57 PM, Russell King - ARM Linux wrote:
> >On Sat, Mar 11, 2017 at 04:30:53PM -0800, Steve Longerbeam wrote:
> >>If it's too difficult to get the imx219 csi-2 transmitter into the
> >>LP-11 state on power on, perhaps the csi-2 receiver can be a little
> >>more lenient on the transmitter and make the LP-11 timeout a warning
> >>instead of error-out.
> >>
> >>Can you try the attached change on top of the version 5 patchset?
> >>
> >>If that doesn't work then you're just going to have to fix the bug
> >>in imx219.
> >
> >That patch gets me past that hurdle, only to reveal that there's another
> >issue:
> 
> Yeah, ipu_cpmem_set_image() failed because it doesn't recognize the
> bayer formats. Wait, didn't we fix this already? I've lost track.
> Ah, right, we were going to move this support into the IPUv3 driver,
> but in the meantime I think you had some patches to get around this.

What I had was this patch for your v3.  I never got to testing your
v4 because of the LP-11 problem.

In v5, you've changed to propagate the ipu_cpmem_set_image() error
code to avoid the resulting corruption, but that leaves the other bits
of this patch unaddressed, along my "media: imx: smfc: add support
for bayer formats" patch.

Your driver basically has no support for bayer formats.

diff --git a/drivers/staging/media/imx/imx-smfc.c b/drivers/staging/media/imx/imx-smfc.c
index 313732201a52..4351c0365cf4 100644
--- a/drivers/staging/media/imx/imx-smfc.c
+++ b/drivers/staging/media/imx/imx-smfc.c
@@ -234,11 +234,6 @@ static void imx_smfc_setup_channel(struct imx_smfc_priv *priv)
 	buf1 = imx_media_dma_buf_get_next_queued(priv->out_ring);
 	priv->next = buf1;
 
-	image.phys0 = buf0->phys;
-	image.phys1 = buf1->phys;
-	ipu_cpmem_set_image(priv->smfc_ch, &image);
-
-
 	switch (image.pix.pixelformat) {
 	case V4L2_PIX_FMT_SBGGR8:
 	case V4L2_PIX_FMT_SGBRG8:
@@ -247,6 +242,10 @@ static void imx_smfc_setup_channel(struct imx_smfc_priv *priv)
 		burst_size = 8;
 		passthrough = true;
 		passthrough_bits = 8;
+		ipu_cpmem_set_resolution(priv->smfc_ch, image.rect.width, image.rect.height);
+		ipu_cpmem_set_stride(priv->smfc_ch, image.pix.bytesperline);
+		ipu_cpmem_set_buffer(priv->smfc_ch, 0, buf0->phys);
+		ipu_cpmem_set_buffer(priv->smfc_ch, 1, buf1->phys);
 		break;
 
 	case V4L2_PIX_FMT_SBGGR16:
@@ -256,9 +255,17 @@ static void imx_smfc_setup_channel(struct imx_smfc_priv *priv)
 		burst_size = 4;
 		passthrough = true;
 		passthrough_bits = 16;
+		ipu_cpmem_set_resolution(priv->smfc_ch, image.rect.width, image.rect.height);
+		ipu_cpmem_set_stride(priv->smfc_ch, image.pix.bytesperline);
+		ipu_cpmem_set_buffer(priv->smfc_ch, 0, buf0->phys);
+		ipu_cpmem_set_buffer(priv->smfc_ch, 1, buf1->phys);
 		break;
 
 	default:
+		image.phys0 = buf0->phys;
+		image.phys1 = buf1->phys;
+		ipu_cpmem_set_image(priv->smfc_ch, &image);
+
 		burst_size = (outfmt->width & 0xf) ? 8 : 16;
 
 		/*

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 12, 2017 at 01:05:06PM -0700, Steve Longerbeam wrote:
> 
> 
> On 03/12/2017 12:57 PM, Russell King - ARM Linux wrote:
> >On Sat, Mar 11, 2017 at 04:30:53PM -0800, Steve Longerbeam wrote:
> >>If it's too difficult to get the imx219 csi-2 transmitter into the
> >>LP-11 state on power on, perhaps the csi-2 receiver can be a little
> >>more lenient on the transmitter and make the LP-11 timeout a warning
> >>instead of error-out.
> >>
> >>Can you try the attached change on top of the version 5 patchset?
> >>
> >>If that doesn't work then you're just going to have to fix the bug
> >>in imx219.
> >
> >That patch gets me past that hurdle, only to reveal that there's another
> >issue:
> 
> Yeah, ipu_cpmem_set_image() failed because it doesn't recognize the
> bayer formats. Wait, didn't we fix this already? I've lost track.
> Ah, right, we were going to move this support into the IPUv3 driver,
> but in the meantime I think you had some patches to get around this.

What I had was this patch for your v3.  I never got to testing your
v4 because of the LP-11 problem.

In v5, you've changed to propagate the ipu_cpmem_set_image() error
code to avoid the resulting corruption, but that leaves the other bits
of this patch unaddressed, along my "media: imx: smfc: add support
for bayer formats" patch.

Your driver basically has no support for bayer formats.

diff --git a/drivers/staging/media/imx/imx-smfc.c b/drivers/staging/media/imx/imx-smfc.c
index 313732201a52..4351c0365cf4 100644
--- a/drivers/staging/media/imx/imx-smfc.c
+++ b/drivers/staging/media/imx/imx-smfc.c
@@ -234,11 +234,6 @@ static void imx_smfc_setup_channel(struct imx_smfc_priv *priv)
 	buf1 = imx_media_dma_buf_get_next_queued(priv->out_ring);
 	priv->next = buf1;
 
-	image.phys0 = buf0->phys;
-	image.phys1 = buf1->phys;
-	ipu_cpmem_set_image(priv->smfc_ch, &image);
-
-
 	switch (image.pix.pixelformat) {
 	case V4L2_PIX_FMT_SBGGR8:
 	case V4L2_PIX_FMT_SGBRG8:
@@ -247,6 +242,10 @@ static void imx_smfc_setup_channel(struct imx_smfc_priv *priv)
 		burst_size = 8;
 		passthrough = true;
 		passthrough_bits = 8;
+		ipu_cpmem_set_resolution(priv->smfc_ch, image.rect.width, image.rect.height);
+		ipu_cpmem_set_stride(priv->smfc_ch, image.pix.bytesperline);
+		ipu_cpmem_set_buffer(priv->smfc_ch, 0, buf0->phys);
+		ipu_cpmem_set_buffer(priv->smfc_ch, 1, buf1->phys);
 		break;
 
 	case V4L2_PIX_FMT_SBGGR16:
@@ -256,9 +255,17 @@ static void imx_smfc_setup_channel(struct imx_smfc_priv *priv)
 		burst_size = 4;
 		passthrough = true;
 		passthrough_bits = 16;
+		ipu_cpmem_set_resolution(priv->smfc_ch, image.rect.width, image.rect.height);
+		ipu_cpmem_set_stride(priv->smfc_ch, image.pix.bytesperline);
+		ipu_cpmem_set_buffer(priv->smfc_ch, 0, buf0->phys);
+		ipu_cpmem_set_buffer(priv->smfc_ch, 1, buf1->phys);
 		break;
 
 	default:
+		image.phys0 = buf0->phys;
+		image.phys1 = buf1->phys;
+		ipu_cpmem_set_image(priv->smfc_ch, &image);
+
 		burst_size = (outfmt->width & 0xf) ? 8 : 16;
 
 		/*

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 12, 2017 at 01:05:06PM -0700, Steve Longerbeam wrote:
> 
> 
> On 03/12/2017 12:57 PM, Russell King - ARM Linux wrote:
> >On Sat, Mar 11, 2017 at 04:30:53PM -0800, Steve Longerbeam wrote:
> >>If it's too difficult to get the imx219 csi-2 transmitter into the
> >>LP-11 state on power on, perhaps the csi-2 receiver can be a little
> >>more lenient on the transmitter and make the LP-11 timeout a warning
> >>instead of error-out.
> >>
> >>Can you try the attached change on top of the version 5 patchset?
> >>
> >>If that doesn't work then you're just going to have to fix the bug
> >>in imx219.
> >
> >That patch gets me past that hurdle, only to reveal that there's another
> >issue:
> 
> Yeah, ipu_cpmem_set_image() failed because it doesn't recognize the
> bayer formats. Wait, didn't we fix this already? I've lost track.
> Ah, right, we were going to move this support into the IPUv3 driver,
> but in the meantime I think you had some patches to get around this.

What I had was this patch for your v3.  I never got to testing your
v4 because of the LP-11 problem.

In v5, you've changed to propagate the ipu_cpmem_set_image() error
code to avoid the resulting corruption, but that leaves the other bits
of this patch unaddressed, along my "media: imx: smfc: add support
for bayer formats" patch.

Your driver basically has no support for bayer formats.

diff --git a/drivers/staging/media/imx/imx-smfc.c b/drivers/staging/media/imx/imx-smfc.c
index 313732201a52..4351c0365cf4 100644
--- a/drivers/staging/media/imx/imx-smfc.c
+++ b/drivers/staging/media/imx/imx-smfc.c
@@ -234,11 +234,6 @@ static void imx_smfc_setup_channel(struct imx_smfc_priv *priv)
 	buf1 = imx_media_dma_buf_get_next_queued(priv->out_ring);
 	priv->next = buf1;
 
-	image.phys0 = buf0->phys;
-	image.phys1 = buf1->phys;
-	ipu_cpmem_set_image(priv->smfc_ch, &image);
-
-
 	switch (image.pix.pixelformat) {
 	case V4L2_PIX_FMT_SBGGR8:
 	case V4L2_PIX_FMT_SGBRG8:
@@ -247,6 +242,10 @@ static void imx_smfc_setup_channel(struct imx_smfc_priv *priv)
 		burst_size = 8;
 		passthrough = true;
 		passthrough_bits = 8;
+		ipu_cpmem_set_resolution(priv->smfc_ch, image.rect.width, image.rect.height);
+		ipu_cpmem_set_stride(priv->smfc_ch, image.pix.bytesperline);
+		ipu_cpmem_set_buffer(priv->smfc_ch, 0, buf0->phys);
+		ipu_cpmem_set_buffer(priv->smfc_ch, 1, buf1->phys);
 		break;
 
 	case V4L2_PIX_FMT_SBGGR16:
@@ -256,9 +255,17 @@ static void imx_smfc_setup_channel(struct imx_smfc_priv *priv)
 		burst_size = 4;
 		passthrough = true;
 		passthrough_bits = 16;
+		ipu_cpmem_set_resolution(priv->smfc_ch, image.rect.width, image.rect.height);
+		ipu_cpmem_set_stride(priv->smfc_ch, image.pix.bytesperline);
+		ipu_cpmem_set_buffer(priv->smfc_ch, 0, buf0->phys);
+		ipu_cpmem_set_buffer(priv->smfc_ch, 1, buf1->phys);
 		break;
 
 	default:
+		image.phys0 = buf0->phys;
+		image.phys1 = buf1->phys;
+		ipu_cpmem_set_image(priv->smfc_ch, &image);
+
 		burst_size = (outfmt->width & 0xf) ? 8 : 16;
 
 		/*

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 01:22 PM, Russell King - ARM Linux wrote:
> On Sun, Mar 12, 2017 at 01:05:06PM -0700, Steve Longerbeam wrote:
>>
>>
>> On 03/12/2017 12:57 PM, Russell King - ARM Linux wrote:
>>> On Sat, Mar 11, 2017 at 04:30:53PM -0800, Steve Longerbeam wrote:
>>>> If it's too difficult to get the imx219 csi-2 transmitter into the
>>>> LP-11 state on power on, perhaps the csi-2 receiver can be a little
>>>> more lenient on the transmitter and make the LP-11 timeout a warning
>>>> instead of error-out.
>>>>
>>>> Can you try the attached change on top of the version 5 patchset?
>>>>
>>>> If that doesn't work then you're just going to have to fix the bug
>>>> in imx219.
>>>
>>> That patch gets me past that hurdle, only to reveal that there's another
>>> issue:
>>
>> Yeah, ipu_cpmem_set_image() failed because it doesn't recognize the
>> bayer formats. Wait, didn't we fix this already? I've lost track.
>> Ah, right, we were going to move this support into the IPUv3 driver,
>> but in the meantime I think you had some patches to get around this.
>
> What I had was this patch for your v3.  I never got to testing your
> v4 because of the LP-11 problem.
>
> In v5, you've changed to propagate the ipu_cpmem_set_image() error
> code to avoid the resulting corruption, but that leaves the other bits
> of this patch unaddressed, along my "media: imx: smfc: add support
> for bayer formats" patch.
>
> Your driver basically has no support for bayer formats.

You added the patches to this driver that adds the bayer support,
I don't think there is anything more required of the driver at this
point to support bayer, the remaining work needs to happen in the IPUv3
driver.

I'll see if I have time to write that patch to IPUv3, but it's simple,
in fact what you wrote below can be translate directly into
ipu_cpmem_set_image(). There's a few other places bayer needs to be
treated in IPUv3, but it should be obvious by grepping for the
reference to pixel formats.

Steve


>
> diff --git a/drivers/staging/media/imx/imx-smfc.c b/drivers/staging/media/imx/imx-smfc.c
> index 313732201a52..4351c0365cf4 100644
> --- a/drivers/staging/media/imx/imx-smfc.c
> +++ b/drivers/staging/media/imx/imx-smfc.c
> @@ -234,11 +234,6 @@ static void imx_smfc_setup_channel(struct imx_smfc_priv *priv)
>  	buf1 = imx_media_dma_buf_get_next_queued(priv->out_ring);
>  	priv->next = buf1;
>
> -	image.phys0 = buf0->phys;
> -	image.phys1 = buf1->phys;
> -	ipu_cpmem_set_image(priv->smfc_ch, &image);
> -
> -
>  	switch (image.pix.pixelformat) {
>  	case V4L2_PIX_FMT_SBGGR8:
>  	case V4L2_PIX_FMT_SGBRG8:
> @@ -247,6 +242,10 @@ static void imx_smfc_setup_channel(struct imx_smfc_priv *priv)
>  		burst_size = 8;
>  		passthrough = true;
>  		passthrough_bits = 8;
> +		ipu_cpmem_set_resolution(priv->smfc_ch, image.rect.width, image.rect.height);
> +		ipu_cpmem_set_stride(priv->smfc_ch, image.pix.bytesperline);
> +		ipu_cpmem_set_buffer(priv->smfc_ch, 0, buf0->phys);
> +		ipu_cpmem_set_buffer(priv->smfc_ch, 1, buf1->phys);
>  		break;
>
>  	case V4L2_PIX_FMT_SBGGR16:
> @@ -256,9 +255,17 @@ static void imx_smfc_setup_channel(struct imx_smfc_priv *priv)
>  		burst_size = 4;
>  		passthrough = true;
>  		passthrough_bits = 16;
> +		ipu_cpmem_set_resolution(priv->smfc_ch, image.rect.width, image.rect.height);
> +		ipu_cpmem_set_stride(priv->smfc_ch, image.pix.bytesperline);
> +		ipu_cpmem_set_buffer(priv->smfc_ch, 0, buf0->phys);
> +		ipu_cpmem_set_buffer(priv->smfc_ch, 1, buf1->phys);
>  		break;
>
>  	default:
> +		image.phys0 = buf0->phys;
> +		image.phys1 = buf1->phys;
> +		ipu_cpmem_set_image(priv->smfc_ch, &image);
> +
>  		burst_size = (outfmt->width & 0xf) ? 8 : 16;
>
>  		/*
>

[PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 01:22 PM, Russell King - ARM Linux wrote:
> On Sun, Mar 12, 2017 at 01:05:06PM -0700, Steve Longerbeam wrote:
>>
>>
>> On 03/12/2017 12:57 PM, Russell King - ARM Linux wrote:
>>> On Sat, Mar 11, 2017 at 04:30:53PM -0800, Steve Longerbeam wrote:
>>>> If it's too difficult to get the imx219 csi-2 transmitter into the
>>>> LP-11 state on power on, perhaps the csi-2 receiver can be a little
>>>> more lenient on the transmitter and make the LP-11 timeout a warning
>>>> instead of error-out.
>>>>
>>>> Can you try the attached change on top of the version 5 patchset?
>>>>
>>>> If that doesn't work then you're just going to have to fix the bug
>>>> in imx219.
>>>
>>> That patch gets me past that hurdle, only to reveal that there's another
>>> issue:
>>
>> Yeah, ipu_cpmem_set_image() failed because it doesn't recognize the
>> bayer formats. Wait, didn't we fix this already? I've lost track.
>> Ah, right, we were going to move this support into the IPUv3 driver,
>> but in the meantime I think you had some patches to get around this.
>
> What I had was this patch for your v3.  I never got to testing your
> v4 because of the LP-11 problem.
>
> In v5, you've changed to propagate the ipu_cpmem_set_image() error
> code to avoid the resulting corruption, but that leaves the other bits
> of this patch unaddressed, along my "media: imx: smfc: add support
> for bayer formats" patch.
>
> Your driver basically has no support for bayer formats.

You added the patches to this driver that adds the bayer support,
I don't think there is anything more required of the driver at this
point to support bayer, the remaining work needs to happen in the IPUv3
driver.

I'll see if I have time to write that patch to IPUv3, but it's simple,
in fact what you wrote below can be translate directly into
ipu_cpmem_set_image(). There's a few other places bayer needs to be
treated in IPUv3, but it should be obvious by grepping for the
reference to pixel formats.

Steve


>
> diff --git a/drivers/staging/media/imx/imx-smfc.c b/drivers/staging/media/imx/imx-smfc.c
> index 313732201a52..4351c0365cf4 100644
> --- a/drivers/staging/media/imx/imx-smfc.c
> +++ b/drivers/staging/media/imx/imx-smfc.c
> @@ -234,11 +234,6 @@ static void imx_smfc_setup_channel(struct imx_smfc_priv *priv)
>  	buf1 = imx_media_dma_buf_get_next_queued(priv->out_ring);
>  	priv->next = buf1;
>
> -	image.phys0 = buf0->phys;
> -	image.phys1 = buf1->phys;
> -	ipu_cpmem_set_image(priv->smfc_ch, &image);
> -
> -
>  	switch (image.pix.pixelformat) {
>  	case V4L2_PIX_FMT_SBGGR8:
>  	case V4L2_PIX_FMT_SGBRG8:
> @@ -247,6 +242,10 @@ static void imx_smfc_setup_channel(struct imx_smfc_priv *priv)
>  		burst_size = 8;
>  		passthrough = true;
>  		passthrough_bits = 8;
> +		ipu_cpmem_set_resolution(priv->smfc_ch, image.rect.width, image.rect.height);
> +		ipu_cpmem_set_stride(priv->smfc_ch, image.pix.bytesperline);
> +		ipu_cpmem_set_buffer(priv->smfc_ch, 0, buf0->phys);
> +		ipu_cpmem_set_buffer(priv->smfc_ch, 1, buf1->phys);
>  		break;
>
>  	case V4L2_PIX_FMT_SBGGR16:
> @@ -256,9 +255,17 @@ static void imx_smfc_setup_channel(struct imx_smfc_priv *priv)
>  		burst_size = 4;
>  		passthrough = true;
>  		passthrough_bits = 16;
> +		ipu_cpmem_set_resolution(priv->smfc_ch, image.rect.width, image.rect.height);
> +		ipu_cpmem_set_stride(priv->smfc_ch, image.pix.bytesperline);
> +		ipu_cpmem_set_buffer(priv->smfc_ch, 0, buf0->phys);
> +		ipu_cpmem_set_buffer(priv->smfc_ch, 1, buf1->phys);
>  		break;
>
>  	default:
> +		image.phys0 = buf0->phys;
> +		image.phys1 = buf1->phys;
> +		ipu_cpmem_set_image(priv->smfc_ch, &image);
> +
>  		burst_size = (outfmt->width & 0xf) ? 8 : 16;
>
>  		/*
>

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 01:22 PM, Russell King - ARM Linux wrote:
> On Sun, Mar 12, 2017 at 01:05:06PM -0700, Steve Longerbeam wrote:
>>
>>
>> On 03/12/2017 12:57 PM, Russell King - ARM Linux wrote:
>>> On Sat, Mar 11, 2017 at 04:30:53PM -0800, Steve Longerbeam wrote:
>>>> If it's too difficult to get the imx219 csi-2 transmitter into the
>>>> LP-11 state on power on, perhaps the csi-2 receiver can be a little
>>>> more lenient on the transmitter and make the LP-11 timeout a warning
>>>> instead of error-out.
>>>>
>>>> Can you try the attached change on top of the version 5 patchset?
>>>>
>>>> If that doesn't work then you're just going to have to fix the bug
>>>> in imx219.
>>>
>>> That patch gets me past that hurdle, only to reveal that there's another
>>> issue:
>>
>> Yeah, ipu_cpmem_set_image() failed because it doesn't recognize the
>> bayer formats. Wait, didn't we fix this already? I've lost track.
>> Ah, right, we were going to move this support into the IPUv3 driver,
>> but in the meantime I think you had some patches to get around this.
>
> What I had was this patch for your v3.  I never got to testing your
> v4 because of the LP-11 problem.
>
> In v5, you've changed to propagate the ipu_cpmem_set_image() error
> code to avoid the resulting corruption, but that leaves the other bits
> of this patch unaddressed, along my "media: imx: smfc: add support
> for bayer formats" patch.
>
> Your driver basically has no support for bayer formats.

You added the patches to this driver that adds the bayer support,
I don't think there is anything more required of the driver at this
point to support bayer, the remaining work needs to happen in the IPUv3
driver.

I'll see if I have time to write that patch to IPUv3, but it's simple,
in fact what you wrote below can be translate directly into
ipu_cpmem_set_image(). There's a few other places bayer needs to be
treated in IPUv3, but it should be obvious by grepping for the
reference to pixel formats.

Steve


>
> diff --git a/drivers/staging/media/imx/imx-smfc.c b/drivers/staging/media/imx/imx-smfc.c
> index 313732201a52..4351c0365cf4 100644
> --- a/drivers/staging/media/imx/imx-smfc.c
> +++ b/drivers/staging/media/imx/imx-smfc.c
> @@ -234,11 +234,6 @@ static void imx_smfc_setup_channel(struct imx_smfc_priv *priv)
>  	buf1 = imx_media_dma_buf_get_next_queued(priv->out_ring);
>  	priv->next = buf1;
>
> -	image.phys0 = buf0->phys;
> -	image.phys1 = buf1->phys;
> -	ipu_cpmem_set_image(priv->smfc_ch, &image);
> -
> -
>  	switch (image.pix.pixelformat) {
>  	case V4L2_PIX_FMT_SBGGR8:
>  	case V4L2_PIX_FMT_SGBRG8:
> @@ -247,6 +242,10 @@ static void imx_smfc_setup_channel(struct imx_smfc_priv *priv)
>  		burst_size = 8;
>  		passthrough = true;
>  		passthrough_bits = 8;
> +		ipu_cpmem_set_resolution(priv->smfc_ch, image.rect.width, image.rect.height);
> +		ipu_cpmem_set_stride(priv->smfc_ch, image.pix.bytesperline);
> +		ipu_cpmem_set_buffer(priv->smfc_ch, 0, buf0->phys);
> +		ipu_cpmem_set_buffer(priv->smfc_ch, 1, buf1->phys);
>  		break;
>
>  	case V4L2_PIX_FMT_SBGGR16:
> @@ -256,9 +255,17 @@ static void imx_smfc_setup_channel(struct imx_smfc_priv *priv)
>  		burst_size = 4;
>  		passthrough = true;
>  		passthrough_bits = 16;
> +		ipu_cpmem_set_resolution(priv->smfc_ch, image.rect.width, image.rect.height);
> +		ipu_cpmem_set_stride(priv->smfc_ch, image.pix.bytesperline);
> +		ipu_cpmem_set_buffer(priv->smfc_ch, 0, buf0->phys);
> +		ipu_cpmem_set_buffer(priv->smfc_ch, 1, buf1->phys);
>  		break;
>
>  	default:
> +		image.phys0 = buf0->phys;
> +		image.phys1 = buf1->phys;
> +		ipu_cpmem_set_image(priv->smfc_ch, &image);
> +
>  		burst_size = (outfmt->width & 0xf) ? 8 : 16;
>
>  		/*
>

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 12, 2017 at 09:26:41PM -0700, Steve Longerbeam wrote:
> On 03/12/2017 01:22 PM, Russell King - ARM Linux wrote:
> >What I had was this patch for your v3.  I never got to testing your
> >v4 because of the LP-11 problem.
> >
> >In v5, you've changed to propagate the ipu_cpmem_set_image() error
> >code to avoid the resulting corruption, but that leaves the other bits
> >of this patch unaddressed, along my "media: imx: smfc: add support
> >for bayer formats" patch.
> >
> >Your driver basically has no support for bayer formats.
> 
> You added the patches to this driver that adds the bayer support,
> I don't think there is anything more required of the driver at this
> point to support bayer, the remaining work needs to happen in the IPUv3
> driver.

There is more work, because the way you've merged my changes to
imx_smfc_setup_channel() into csi_idmac_setup_channel() is wrong with
respect to the burst size.

You always set it to 8 or 16 depending on the width:

	burst_size = (image.pix.width & 0xf) ? 8 : 16;

	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);

and then you have my switch() statement which assigns burst_size.
My _tested_ code removed the above, added the switch, which had
a default case which reflected the above setting:

	default:
		burst_size = (outfmt->width & 0xf) ? 8 : 16;

and then went on to set the burst size _after_ the switch statement:

	ipu_cpmem_set_burstsize(priv->smfc_ch, burst_size);

The effect is unchanged for non-bayer formats.  For bayer formats, the
burst size is determined by the bayer data size.

So, even if it's appropriate to fix ipu_cpmem_set_image(), fixing the
above is still required.

I'm not convinced that fixing ipu_cpmem_set_image() is even the best
solution - it's not as trivial as it looks on the surface:

        ipu_cpmem_set_resolution(ch, image->rect.width, image->rect.height);
        ipu_cpmem_set_stride(ch, pix->bytesperline);

this is fine, it doesn't depend on the format.  However, the next line:

        ipu_cpmem_set_fmt(ch, v4l2_pix_fmt_to_drm_fourcc(pix->pixelformat));

does - v4l2_pix_fmt_to_drm_fourcc() is a locally defined function (it
isn't v4l2 code) that converts a v4l2 pixel format to a DRM fourcc.
DRM knows nothing about bayer formats, there aren't fourcc codes in
DRM for it.  The result is that v4l2_pix_fmt_to_drm_fourcc() returns
-EINVAL cast to a u32, which gets passed unchecked into ipu_cpmem_set_fmt().

ipu_cpmem_set_fmt() won't recognise that, and also returns -EINVAL - and
it's a bug that this is not checked and propagated.  If it is checked and
propagated, then we need this to support bayer formats, and I don't see
DRM people wanting bayer format fourcc codes added without there being
a real DRM driver wanting to use them.

Then there's the business of calculating the top-left offset of the image,
which for bayer always needs to be an even number of pixels - as this
function takes the top-left offset, it ought to respect it, but if it
doesn't meet this criteria, what should it do?  csi_idmac_setup_channel()
always sets them to zero, but that's not really something that
ipu_cpmem_set_image() should assume.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 12, 2017 at 09:26:41PM -0700, Steve Longerbeam wrote:
> On 03/12/2017 01:22 PM, Russell King - ARM Linux wrote:
> >What I had was this patch for your v3.  I never got to testing your
> >v4 because of the LP-11 problem.
> >
> >In v5, you've changed to propagate the ipu_cpmem_set_image() error
> >code to avoid the resulting corruption, but that leaves the other bits
> >of this patch unaddressed, along my "media: imx: smfc: add support
> >for bayer formats" patch.
> >
> >Your driver basically has no support for bayer formats.
> 
> You added the patches to this driver that adds the bayer support,
> I don't think there is anything more required of the driver at this
> point to support bayer, the remaining work needs to happen in the IPUv3
> driver.

There is more work, because the way you've merged my changes to
imx_smfc_setup_channel() into csi_idmac_setup_channel() is wrong with
respect to the burst size.

You always set it to 8 or 16 depending on the width:

	burst_size = (image.pix.width & 0xf) ? 8 : 16;

	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);

and then you have my switch() statement which assigns burst_size.
My _tested_ code removed the above, added the switch, which had
a default case which reflected the above setting:

	default:
		burst_size = (outfmt->width & 0xf) ? 8 : 16;

and then went on to set the burst size _after_ the switch statement:

	ipu_cpmem_set_burstsize(priv->smfc_ch, burst_size);

The effect is unchanged for non-bayer formats.  For bayer formats, the
burst size is determined by the bayer data size.

So, even if it's appropriate to fix ipu_cpmem_set_image(), fixing the
above is still required.

I'm not convinced that fixing ipu_cpmem_set_image() is even the best
solution - it's not as trivial as it looks on the surface:

        ipu_cpmem_set_resolution(ch, image->rect.width, image->rect.height);
        ipu_cpmem_set_stride(ch, pix->bytesperline);

this is fine, it doesn't depend on the format.  However, the next line:

        ipu_cpmem_set_fmt(ch, v4l2_pix_fmt_to_drm_fourcc(pix->pixelformat));

does - v4l2_pix_fmt_to_drm_fourcc() is a locally defined function (it
isn't v4l2 code) that converts a v4l2 pixel format to a DRM fourcc.
DRM knows nothing about bayer formats, there aren't fourcc codes in
DRM for it.  The result is that v4l2_pix_fmt_to_drm_fourcc() returns
-EINVAL cast to a u32, which gets passed unchecked into ipu_cpmem_set_fmt().

ipu_cpmem_set_fmt() won't recognise that, and also returns -EINVAL - and
it's a bug that this is not checked and propagated.  If it is checked and
propagated, then we need this to support bayer formats, and I don't see
DRM people wanting bayer format fourcc codes added without there being
a real DRM driver wanting to use them.

Then there's the business of calculating the top-left offset of the image,
which for bayer always needs to be an even number of pixels - as this
function takes the top-left offset, it ought to respect it, but if it
doesn't meet this criteria, what should it do?  csi_idmac_setup_channel()
always sets them to zero, but that's not really something that
ipu_cpmem_set_image() should assume.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 12, 2017 at 09:26:41PM -0700, Steve Longerbeam wrote:
> On 03/12/2017 01:22 PM, Russell King - ARM Linux wrote:
> >What I had was this patch for your v3.  I never got to testing your
> >v4 because of the LP-11 problem.
> >
> >In v5, you've changed to propagate the ipu_cpmem_set_image() error
> >code to avoid the resulting corruption, but that leaves the other bits
> >of this patch unaddressed, along my "media: imx: smfc: add support
> >for bayer formats" patch.
> >
> >Your driver basically has no support for bayer formats.
> 
> You added the patches to this driver that adds the bayer support,
> I don't think there is anything more required of the driver at this
> point to support bayer, the remaining work needs to happen in the IPUv3
> driver.

There is more work, because the way you've merged my changes to
imx_smfc_setup_channel() into csi_idmac_setup_channel() is wrong with
respect to the burst size.

You always set it to 8 or 16 depending on the width:

	burst_size = (image.pix.width & 0xf) ? 8 : 16;

	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);

and then you have my switch() statement which assigns burst_size.
My _tested_ code removed the above, added the switch, which had
a default case which reflected the above setting:

	default:
		burst_size = (outfmt->width & 0xf) ? 8 : 16;

and then went on to set the burst size _after_ the switch statement:

	ipu_cpmem_set_burstsize(priv->smfc_ch, burst_size);

The effect is unchanged for non-bayer formats.  For bayer formats, the
burst size is determined by the bayer data size.

So, even if it's appropriate to fix ipu_cpmem_set_image(), fixing the
above is still required.

I'm not convinced that fixing ipu_cpmem_set_image() is even the best
solution - it's not as trivial as it looks on the surface:

        ipu_cpmem_set_resolution(ch, image->rect.width, image->rect.height);
        ipu_cpmem_set_stride(ch, pix->bytesperline);

this is fine, it doesn't depend on the format.  However, the next line:

        ipu_cpmem_set_fmt(ch, v4l2_pix_fmt_to_drm_fourcc(pix->pixelformat));

does - v4l2_pix_fmt_to_drm_fourcc() is a locally defined function (it
isn't v4l2 code) that converts a v4l2 pixel format to a DRM fourcc.
DRM knows nothing about bayer formats, there aren't fourcc codes in
DRM for it.  The result is that v4l2_pix_fmt_to_drm_fourcc() returns
-EINVAL cast to a u32, which gets passed unchecked into ipu_cpmem_set_fmt().

ipu_cpmem_set_fmt() won't recognise that, and also returns -EINVAL - and
it's a bug that this is not checked and propagated.  If it is checked and
propagated, then we need this to support bayer formats, and I don't see
DRM people wanting bayer format fourcc codes added without there being
a real DRM driver wanting to use them.

Then there's the business of calculating the top-left offset of the image,
which for bayer always needs to be an even number of pixels - as this
function takes the top-left offset, it ought to respect it, but if it
doesn't meet this criteria, what should it do?  csi_idmac_setup_channel()
always sets them to zero, but that's not really something that
ipu_cpmem_set_image() should assume.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Mon, Mar 13, 2017 at 08:16:25AM +0000, Russell King - ARM Linux wrote:
> On Sun, Mar 12, 2017 at 09:26:41PM -0700, Steve Longerbeam wrote:
> > On 03/12/2017 01:22 PM, Russell King - ARM Linux wrote:
> > >What I had was this patch for your v3.  I never got to testing your
> > >v4 because of the LP-11 problem.
> > >
> > >In v5, you've changed to propagate the ipu_cpmem_set_image() error
> > >code to avoid the resulting corruption, but that leaves the other bits
> > >of this patch unaddressed, along my "media: imx: smfc: add support
> > >for bayer formats" patch.
> > >
> > >Your driver basically has no support for bayer formats.
> > 
> > You added the patches to this driver that adds the bayer support,
> > I don't think there is anything more required of the driver at this
> > point to support bayer, the remaining work needs to happen in the IPUv3
> > driver.
> 
> There is more work, because the way you've merged my changes to
> imx_smfc_setup_channel() into csi_idmac_setup_channel() is wrong with
> respect to the burst size.
> 
> You always set it to 8 or 16 depending on the width:
> 
> 	burst_size = (image.pix.width & 0xf) ? 8 : 16;
> 
> 	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
> 
> and then you have my switch() statement which assigns burst_size.
> My _tested_ code removed the above, added the switch, which had
> a default case which reflected the above setting:
> 
> 	default:
> 		burst_size = (outfmt->width & 0xf) ? 8 : 16;
> 
> and then went on to set the burst size _after_ the switch statement:
> 
> 	ipu_cpmem_set_burstsize(priv->smfc_ch, burst_size);
> 
> The effect is unchanged for non-bayer formats.  For bayer formats, the
> burst size is determined by the bayer data size.
> 
> So, even if it's appropriate to fix ipu_cpmem_set_image(), fixing the
> above is still required.
> 
> I'm not convinced that fixing ipu_cpmem_set_image() is even the best
> solution - it's not as trivial as it looks on the surface:
> 
>         ipu_cpmem_set_resolution(ch, image->rect.width, image->rect.height);
>         ipu_cpmem_set_stride(ch, pix->bytesperline);
> 
> this is fine, it doesn't depend on the format.  However, the next line:
> 
>         ipu_cpmem_set_fmt(ch, v4l2_pix_fmt_to_drm_fourcc(pix->pixelformat));
> 
> does - v4l2_pix_fmt_to_drm_fourcc() is a locally defined function (it
> isn't v4l2 code) that converts a v4l2 pixel format to a DRM fourcc.
> DRM knows nothing about bayer formats, there aren't fourcc codes in
> DRM for it.  The result is that v4l2_pix_fmt_to_drm_fourcc() returns
> -EINVAL cast to a u32, which gets passed unchecked into ipu_cpmem_set_fmt().
> 
> ipu_cpmem_set_fmt() won't recognise that, and also returns -EINVAL - and
> it's a bug that this is not checked and propagated.  If it is checked and
> propagated, then we need this to support bayer formats, and I don't see
> DRM people wanting bayer format fourcc codes added without there being
> a real DRM driver wanting to use them.
> 
> Then there's the business of calculating the top-left offset of the image,
> which for bayer always needs to be an even number of pixels - as this
> function takes the top-left offset, it ought to respect it, but if it
> doesn't meet this criteria, what should it do?  csi_idmac_setup_channel()
> always sets them to zero, but that's not really something that
> ipu_cpmem_set_image() should assume.

For the time being, I've restored the functionality along the same lines
as I originally had.  This seems to get me working capture, but might
break non-bayer passthrough mode:

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index fc0036aa84d0..df336971a009 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -314,14 +314,6 @@ static int csi_idmac_setup_channel(struct csi_priv *priv)
 	image.phys0 = phys[0];
 	image.phys1 = phys[1];
 
-	ret = ipu_cpmem_set_image(priv->idmac_ch, &image);
-	if (ret)
-		return ret;
-
-	burst_size = (image.pix.width & 0xf) ? 8 : 16;
-
-	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
-
 	/*
 	 * Check for conditions that require the IPU to handle the
 	 * data internally as generic data, aka passthrough mode:
@@ -346,15 +338,29 @@ static int csi_idmac_setup_channel(struct csi_priv *priv)
 		passthrough_bits = 16;
 		break;
 	default:
+		burst_size = (image.pix.width & 0xf) ? 8 : 16;
 		passthrough = (sensor_ep->bus_type != V4L2_MBUS_CSI2 &&
 			       sensor_ep->bus.parallel.bus_width >= 16);
 		passthrough_bits = 16;
 		break;
 	}
 
-	if (passthrough)
+	if (passthrough) {
+		ipu_cpmem_set_resolution(priv->idmac_ch, image.rect.width,
+					 image.rect.height);
+		ipu_cpmem_set_stride(priv->idmac_ch, image.pix.bytesperline);
+		ipu_cpmem_set_buffer(priv->idmac_ch, 0, image.phys0);
+		ipu_cpmem_set_buffer(priv->idmac_ch, 1, image.phys1);
+		ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
 		ipu_cpmem_set_format_passthrough(priv->idmac_ch,
 						 passthrough_bits);
+	} else {
+		ret = ipu_cpmem_set_image(priv->idmac_ch, &image);
+		if (ret)
+			return ret;
+
+		ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
+	}
 
 	/*
 	 * Set the channel for the direct CSI-->memory via SMFC


-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Mon, Mar 13, 2017 at 08:16:25AM +0000, Russell King - ARM Linux wrote:
> On Sun, Mar 12, 2017 at 09:26:41PM -0700, Steve Longerbeam wrote:
> > On 03/12/2017 01:22 PM, Russell King - ARM Linux wrote:
> > >What I had was this patch for your v3.  I never got to testing your
> > >v4 because of the LP-11 problem.
> > >
> > >In v5, you've changed to propagate the ipu_cpmem_set_image() error
> > >code to avoid the resulting corruption, but that leaves the other bits
> > >of this patch unaddressed, along my "media: imx: smfc: add support
> > >for bayer formats" patch.
> > >
> > >Your driver basically has no support for bayer formats.
> > 
> > You added the patches to this driver that adds the bayer support,
> > I don't think there is anything more required of the driver at this
> > point to support bayer, the remaining work needs to happen in the IPUv3
> > driver.
> 
> There is more work, because the way you've merged my changes to
> imx_smfc_setup_channel() into csi_idmac_setup_channel() is wrong with
> respect to the burst size.
> 
> You always set it to 8 or 16 depending on the width:
> 
> 	burst_size = (image.pix.width & 0xf) ? 8 : 16;
> 
> 	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
> 
> and then you have my switch() statement which assigns burst_size.
> My _tested_ code removed the above, added the switch, which had
> a default case which reflected the above setting:
> 
> 	default:
> 		burst_size = (outfmt->width & 0xf) ? 8 : 16;
> 
> and then went on to set the burst size _after_ the switch statement:
> 
> 	ipu_cpmem_set_burstsize(priv->smfc_ch, burst_size);
> 
> The effect is unchanged for non-bayer formats.  For bayer formats, the
> burst size is determined by the bayer data size.
> 
> So, even if it's appropriate to fix ipu_cpmem_set_image(), fixing the
> above is still required.
> 
> I'm not convinced that fixing ipu_cpmem_set_image() is even the best
> solution - it's not as trivial as it looks on the surface:
> 
>         ipu_cpmem_set_resolution(ch, image->rect.width, image->rect.height);
>         ipu_cpmem_set_stride(ch, pix->bytesperline);
> 
> this is fine, it doesn't depend on the format.  However, the next line:
> 
>         ipu_cpmem_set_fmt(ch, v4l2_pix_fmt_to_drm_fourcc(pix->pixelformat));
> 
> does - v4l2_pix_fmt_to_drm_fourcc() is a locally defined function (it
> isn't v4l2 code) that converts a v4l2 pixel format to a DRM fourcc.
> DRM knows nothing about bayer formats, there aren't fourcc codes in
> DRM for it.  The result is that v4l2_pix_fmt_to_drm_fourcc() returns
> -EINVAL cast to a u32, which gets passed unchecked into ipu_cpmem_set_fmt().
> 
> ipu_cpmem_set_fmt() won't recognise that, and also returns -EINVAL - and
> it's a bug that this is not checked and propagated.  If it is checked and
> propagated, then we need this to support bayer formats, and I don't see
> DRM people wanting bayer format fourcc codes added without there being
> a real DRM driver wanting to use them.
> 
> Then there's the business of calculating the top-left offset of the image,
> which for bayer always needs to be an even number of pixels - as this
> function takes the top-left offset, it ought to respect it, but if it
> doesn't meet this criteria, what should it do?  csi_idmac_setup_channel()
> always sets them to zero, but that's not really something that
> ipu_cpmem_set_image() should assume.

For the time being, I've restored the functionality along the same lines
as I originally had.  This seems to get me working capture, but might
break non-bayer passthrough mode:

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index fc0036aa84d0..df336971a009 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -314,14 +314,6 @@ static int csi_idmac_setup_channel(struct csi_priv *priv)
 	image.phys0 = phys[0];
 	image.phys1 = phys[1];
 
-	ret = ipu_cpmem_set_image(priv->idmac_ch, &image);
-	if (ret)
-		return ret;
-
-	burst_size = (image.pix.width & 0xf) ? 8 : 16;
-
-	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
-
 	/*
 	 * Check for conditions that require the IPU to handle the
 	 * data internally as generic data, aka passthrough mode:
@@ -346,15 +338,29 @@ static int csi_idmac_setup_channel(struct csi_priv *priv)
 		passthrough_bits = 16;
 		break;
 	default:
+		burst_size = (image.pix.width & 0xf) ? 8 : 16;
 		passthrough = (sensor_ep->bus_type != V4L2_MBUS_CSI2 &&
 			       sensor_ep->bus.parallel.bus_width >= 16);
 		passthrough_bits = 16;
 		break;
 	}
 
-	if (passthrough)
+	if (passthrough) {
+		ipu_cpmem_set_resolution(priv->idmac_ch, image.rect.width,
+					 image.rect.height);
+		ipu_cpmem_set_stride(priv->idmac_ch, image.pix.bytesperline);
+		ipu_cpmem_set_buffer(priv->idmac_ch, 0, image.phys0);
+		ipu_cpmem_set_buffer(priv->idmac_ch, 1, image.phys1);
+		ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
 		ipu_cpmem_set_format_passthrough(priv->idmac_ch,
 						 passthrough_bits);
+	} else {
+		ret = ipu_cpmem_set_image(priv->idmac_ch, &image);
+		if (ret)
+			return ret;
+
+		ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
+	}
 
 	/*
 	 * Set the channel for the direct CSI-->memory via SMFC


-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Mon, Mar 13, 2017 at 08:16:25AM +0000, Russell King - ARM Linux wrote:
> On Sun, Mar 12, 2017 at 09:26:41PM -0700, Steve Longerbeam wrote:
> > On 03/12/2017 01:22 PM, Russell King - ARM Linux wrote:
> > >What I had was this patch for your v3.  I never got to testing your
> > >v4 because of the LP-11 problem.
> > >
> > >In v5, you've changed to propagate the ipu_cpmem_set_image() error
> > >code to avoid the resulting corruption, but that leaves the other bits
> > >of this patch unaddressed, along my "media: imx: smfc: add support
> > >for bayer formats" patch.
> > >
> > >Your driver basically has no support for bayer formats.
> > 
> > You added the patches to this driver that adds the bayer support,
> > I don't think there is anything more required of the driver at this
> > point to support bayer, the remaining work needs to happen in the IPUv3
> > driver.
> 
> There is more work, because the way you've merged my changes to
> imx_smfc_setup_channel() into csi_idmac_setup_channel() is wrong with
> respect to the burst size.
> 
> You always set it to 8 or 16 depending on the width:
> 
> 	burst_size = (image.pix.width & 0xf) ? 8 : 16;
> 
> 	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
> 
> and then you have my switch() statement which assigns burst_size.
> My _tested_ code removed the above, added the switch, which had
> a default case which reflected the above setting:
> 
> 	default:
> 		burst_size = (outfmt->width & 0xf) ? 8 : 16;
> 
> and then went on to set the burst size _after_ the switch statement:
> 
> 	ipu_cpmem_set_burstsize(priv->smfc_ch, burst_size);
> 
> The effect is unchanged for non-bayer formats.  For bayer formats, the
> burst size is determined by the bayer data size.
> 
> So, even if it's appropriate to fix ipu_cpmem_set_image(), fixing the
> above is still required.
> 
> I'm not convinced that fixing ipu_cpmem_set_image() is even the best
> solution - it's not as trivial as it looks on the surface:
> 
>         ipu_cpmem_set_resolution(ch, image->rect.width, image->rect.height);
>         ipu_cpmem_set_stride(ch, pix->bytesperline);
> 
> this is fine, it doesn't depend on the format.  However, the next line:
> 
>         ipu_cpmem_set_fmt(ch, v4l2_pix_fmt_to_drm_fourcc(pix->pixelformat));
> 
> does - v4l2_pix_fmt_to_drm_fourcc() is a locally defined function (it
> isn't v4l2 code) that converts a v4l2 pixel format to a DRM fourcc.
> DRM knows nothing about bayer formats, there aren't fourcc codes in
> DRM for it.  The result is that v4l2_pix_fmt_to_drm_fourcc() returns
> -EINVAL cast to a u32, which gets passed unchecked into ipu_cpmem_set_fmt().
> 
> ipu_cpmem_set_fmt() won't recognise that, and also returns -EINVAL - and
> it's a bug that this is not checked and propagated.  If it is checked and
> propagated, then we need this to support bayer formats, and I don't see
> DRM people wanting bayer format fourcc codes added without there being
> a real DRM driver wanting to use them.
> 
> Then there's the business of calculating the top-left offset of the image,
> which for bayer always needs to be an even number of pixels - as this
> function takes the top-left offset, it ought to respect it, but if it
> doesn't meet this criteria, what should it do?  csi_idmac_setup_channel()
> always sets them to zero, but that's not really something that
> ipu_cpmem_set_image() should assume.

For the time being, I've restored the functionality along the same lines
as I originally had.  This seems to get me working capture, but might
break non-bayer passthrough mode:

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index fc0036aa84d0..df336971a009 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -314,14 +314,6 @@ static int csi_idmac_setup_channel(struct csi_priv *priv)
 	image.phys0 = phys[0];
 	image.phys1 = phys[1];
 
-	ret = ipu_cpmem_set_image(priv->idmac_ch, &image);
-	if (ret)
-		return ret;
-
-	burst_size = (image.pix.width & 0xf) ? 8 : 16;
-
-	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
-
 	/*
 	 * Check for conditions that require the IPU to handle the
 	 * data internally as generic data, aka passthrough mode:
@@ -346,15 +338,29 @@ static int csi_idmac_setup_channel(struct csi_priv *priv)
 		passthrough_bits = 16;
 		break;
 	default:
+		burst_size = (image.pix.width & 0xf) ? 8 : 16;
 		passthrough = (sensor_ep->bus_type != V4L2_MBUS_CSI2 &&
 			       sensor_ep->bus.parallel.bus_width >= 16);
 		passthrough_bits = 16;
 		break;
 	}
 
-	if (passthrough)
+	if (passthrough) {
+		ipu_cpmem_set_resolution(priv->idmac_ch, image.rect.width,
+					 image.rect.height);
+		ipu_cpmem_set_stride(priv->idmac_ch, image.pix.bytesperline);
+		ipu_cpmem_set_buffer(priv->idmac_ch, 0, image.phys0);
+		ipu_cpmem_set_buffer(priv->idmac_ch, 1, image.phys1);
+		ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
 		ipu_cpmem_set_format_passthrough(priv->idmac_ch,
 						 passthrough_bits);
+	} else {
+		ret = ipu_cpmem_set_image(priv->idmac_ch, &image);
+		if (ret)
+			return ret;
+
+		ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
+	}
 
 	/*
 	 * Set the channel for the direct CSI-->memory via SMFC


-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

er, I meant I will integrate this patch. And verify/fix
possible breakage for non-bayer passthrough.

Steve


On 03/13/2017 02:30 AM, Russell King - ARM Linux wrote:
> On Mon, Mar 13, 2017 at 08:16:25AM +0000, Russell King - ARM Linux wrote:
>> On Sun, Mar 12, 2017 at 09:26:41PM -0700, Steve Longerbeam wrote:
>>> On 03/12/2017 01:22 PM, Russell King - ARM Linux wrote:
>>>> What I had was this patch for your v3.  I never got to testing your
>>>> v4 because of the LP-11 problem.
>>>>
>>>> In v5, you've changed to propagate the ipu_cpmem_set_image() error
>>>> code to avoid the resulting corruption, but that leaves the other bits
>>>> of this patch unaddressed, along my "media: imx: smfc: add support
>>>> for bayer formats" patch.
>>>>
>>>> Your driver basically has no support for bayer formats.
>>> You added the patches to this driver that adds the bayer support,
>>> I don't think there is anything more required of the driver at this
>>> point to support bayer, the remaining work needs to happen in the IPUv3
>>> driver.
>> There is more work, because the way you've merged my changes to
>> imx_smfc_setup_channel() into csi_idmac_setup_channel() is wrong with
>> respect to the burst size.
>>
>> You always set it to 8 or 16 depending on the width:
>>
>> 	burst_size = (image.pix.width & 0xf) ? 8 : 16;
>>
>> 	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
>>
>> and then you have my switch() statement which assigns burst_size.
>> My _tested_ code removed the above, added the switch, which had
>> a default case which reflected the above setting:
>>
>> 	default:
>> 		burst_size = (outfmt->width & 0xf) ? 8 : 16;
>>
>> and then went on to set the burst size _after_ the switch statement:
>>
>> 	ipu_cpmem_set_burstsize(priv->smfc_ch, burst_size);
>>
>> The effect is unchanged for non-bayer formats.  For bayer formats, the
>> burst size is determined by the bayer data size.
>>
>> So, even if it's appropriate to fix ipu_cpmem_set_image(), fixing the
>> above is still required.
>>
>> I'm not convinced that fixing ipu_cpmem_set_image() is even the best
>> solution - it's not as trivial as it looks on the surface:
>>
>>          ipu_cpmem_set_resolution(ch, image->rect.width, image->rect.height);
>>          ipu_cpmem_set_stride(ch, pix->bytesperline);
>>
>> this is fine, it doesn't depend on the format.  However, the next line:
>>
>>          ipu_cpmem_set_fmt(ch, v4l2_pix_fmt_to_drm_fourcc(pix->pixelformat));
>>
>> does - v4l2_pix_fmt_to_drm_fourcc() is a locally defined function (it
>> isn't v4l2 code) that converts a v4l2 pixel format to a DRM fourcc.
>> DRM knows nothing about bayer formats, there aren't fourcc codes in
>> DRM for it.  The result is that v4l2_pix_fmt_to_drm_fourcc() returns
>> -EINVAL cast to a u32, which gets passed unchecked into ipu_cpmem_set_fmt().
>>
>> ipu_cpmem_set_fmt() won't recognise that, and also returns -EINVAL - and
>> it's a bug that this is not checked and propagated.  If it is checked and
>> propagated, then we need this to support bayer formats, and I don't see
>> DRM people wanting bayer format fourcc codes added without there being
>> a real DRM driver wanting to use them.
>>
>> Then there's the business of calculating the top-left offset of the image,
>> which for bayer always needs to be an even number of pixels - as this
>> function takes the top-left offset, it ought to respect it, but if it
>> doesn't meet this criteria, what should it do?  csi_idmac_setup_channel()
>> always sets them to zero, but that's not really something that
>> ipu_cpmem_set_image() should assume.
> For the time being, I've restored the functionality along the same lines
> as I originally had.  This seems to get me working capture, but might
> break non-bayer passthrough mode:
>
> diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
> index fc0036aa84d0..df336971a009 100644
> --- a/drivers/staging/media/imx/imx-media-csi.c
> +++ b/drivers/staging/media/imx/imx-media-csi.c
> @@ -314,14 +314,6 @@ static int csi_idmac_setup_channel(struct csi_priv *priv)
>   	image.phys0 = phys[0];
>   	image.phys1 = phys[1];
>   
> -	ret = ipu_cpmem_set_image(priv->idmac_ch, &image);
> -	if (ret)
> -		return ret;
> -
> -	burst_size = (image.pix.width & 0xf) ? 8 : 16;
> -
> -	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
> -
>   	/*
>   	 * Check for conditions that require the IPU to handle the
>   	 * data internally as generic data, aka passthrough mode:
> @@ -346,15 +338,29 @@ static int csi_idmac_setup_channel(struct csi_priv *priv)
>   		passthrough_bits = 16;
>   		break;
>   	default:
> +		burst_size = (image.pix.width & 0xf) ? 8 : 16;
>   		passthrough = (sensor_ep->bus_type != V4L2_MBUS_CSI2 &&
>   			       sensor_ep->bus.parallel.bus_width >= 16);
>   		passthrough_bits = 16;
>   		break;
>   	}
>   
> -	if (passthrough)
> +	if (passthrough) {
> +		ipu_cpmem_set_resolution(priv->idmac_ch, image.rect.width,
> +					 image.rect.height);
> +		ipu_cpmem_set_stride(priv->idmac_ch, image.pix.bytesperline);
> +		ipu_cpmem_set_buffer(priv->idmac_ch, 0, image.phys0);
> +		ipu_cpmem_set_buffer(priv->idmac_ch, 1, image.phys1);
> +		ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
>   		ipu_cpmem_set_format_passthrough(priv->idmac_ch,
>   						 passthrough_bits);
> +	} else {
> +		ret = ipu_cpmem_set_image(priv->idmac_ch, &image);
> +		if (ret)
> +			return ret;
> +
> +		ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
> +	}
>   
>   	/*
>   	 * Set the channel for the direct CSI-->memory via SMFC
>
>

[PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

er, I meant I will integrate this patch. And verify/fix
possible breakage for non-bayer passthrough.

Steve


On 03/13/2017 02:30 AM, Russell King - ARM Linux wrote:
> On Mon, Mar 13, 2017 at 08:16:25AM +0000, Russell King - ARM Linux wrote:
>> On Sun, Mar 12, 2017 at 09:26:41PM -0700, Steve Longerbeam wrote:
>>> On 03/12/2017 01:22 PM, Russell King - ARM Linux wrote:
>>>> What I had was this patch for your v3.  I never got to testing your
>>>> v4 because of the LP-11 problem.
>>>>
>>>> In v5, you've changed to propagate the ipu_cpmem_set_image() error
>>>> code to avoid the resulting corruption, but that leaves the other bits
>>>> of this patch unaddressed, along my "media: imx: smfc: add support
>>>> for bayer formats" patch.
>>>>
>>>> Your driver basically has no support for bayer formats.
>>> You added the patches to this driver that adds the bayer support,
>>> I don't think there is anything more required of the driver at this
>>> point to support bayer, the remaining work needs to happen in the IPUv3
>>> driver.
>> There is more work, because the way you've merged my changes to
>> imx_smfc_setup_channel() into csi_idmac_setup_channel() is wrong with
>> respect to the burst size.
>>
>> You always set it to 8 or 16 depending on the width:
>>
>> 	burst_size = (image.pix.width & 0xf) ? 8 : 16;
>>
>> 	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
>>
>> and then you have my switch() statement which assigns burst_size.
>> My _tested_ code removed the above, added the switch, which had
>> a default case which reflected the above setting:
>>
>> 	default:
>> 		burst_size = (outfmt->width & 0xf) ? 8 : 16;
>>
>> and then went on to set the burst size _after_ the switch statement:
>>
>> 	ipu_cpmem_set_burstsize(priv->smfc_ch, burst_size);
>>
>> The effect is unchanged for non-bayer formats.  For bayer formats, the
>> burst size is determined by the bayer data size.
>>
>> So, even if it's appropriate to fix ipu_cpmem_set_image(), fixing the
>> above is still required.
>>
>> I'm not convinced that fixing ipu_cpmem_set_image() is even the best
>> solution - it's not as trivial as it looks on the surface:
>>
>>          ipu_cpmem_set_resolution(ch, image->rect.width, image->rect.height);
>>          ipu_cpmem_set_stride(ch, pix->bytesperline);
>>
>> this is fine, it doesn't depend on the format.  However, the next line:
>>
>>          ipu_cpmem_set_fmt(ch, v4l2_pix_fmt_to_drm_fourcc(pix->pixelformat));
>>
>> does - v4l2_pix_fmt_to_drm_fourcc() is a locally defined function (it
>> isn't v4l2 code) that converts a v4l2 pixel format to a DRM fourcc.
>> DRM knows nothing about bayer formats, there aren't fourcc codes in
>> DRM for it.  The result is that v4l2_pix_fmt_to_drm_fourcc() returns
>> -EINVAL cast to a u32, which gets passed unchecked into ipu_cpmem_set_fmt().
>>
>> ipu_cpmem_set_fmt() won't recognise that, and also returns -EINVAL - and
>> it's a bug that this is not checked and propagated.  If it is checked and
>> propagated, then we need this to support bayer formats, and I don't see
>> DRM people wanting bayer format fourcc codes added without there being
>> a real DRM driver wanting to use them.
>>
>> Then there's the business of calculating the top-left offset of the image,
>> which for bayer always needs to be an even number of pixels - as this
>> function takes the top-left offset, it ought to respect it, but if it
>> doesn't meet this criteria, what should it do?  csi_idmac_setup_channel()
>> always sets them to zero, but that's not really something that
>> ipu_cpmem_set_image() should assume.
> For the time being, I've restored the functionality along the same lines
> as I originally had.  This seems to get me working capture, but might
> break non-bayer passthrough mode:
>
> diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
> index fc0036aa84d0..df336971a009 100644
> --- a/drivers/staging/media/imx/imx-media-csi.c
> +++ b/drivers/staging/media/imx/imx-media-csi.c
> @@ -314,14 +314,6 @@ static int csi_idmac_setup_channel(struct csi_priv *priv)
>   	image.phys0 = phys[0];
>   	image.phys1 = phys[1];
>   
> -	ret = ipu_cpmem_set_image(priv->idmac_ch, &image);
> -	if (ret)
> -		return ret;
> -
> -	burst_size = (image.pix.width & 0xf) ? 8 : 16;
> -
> -	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
> -
>   	/*
>   	 * Check for conditions that require the IPU to handle the
>   	 * data internally as generic data, aka passthrough mode:
> @@ -346,15 +338,29 @@ static int csi_idmac_setup_channel(struct csi_priv *priv)
>   		passthrough_bits = 16;
>   		break;
>   	default:
> +		burst_size = (image.pix.width & 0xf) ? 8 : 16;
>   		passthrough = (sensor_ep->bus_type != V4L2_MBUS_CSI2 &&
>   			       sensor_ep->bus.parallel.bus_width >= 16);
>   		passthrough_bits = 16;
>   		break;
>   	}
>   
> -	if (passthrough)
> +	if (passthrough) {
> +		ipu_cpmem_set_resolution(priv->idmac_ch, image.rect.width,
> +					 image.rect.height);
> +		ipu_cpmem_set_stride(priv->idmac_ch, image.pix.bytesperline);
> +		ipu_cpmem_set_buffer(priv->idmac_ch, 0, image.phys0);
> +		ipu_cpmem_set_buffer(priv->idmac_ch, 1, image.phys1);
> +		ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
>   		ipu_cpmem_set_format_passthrough(priv->idmac_ch,
>   						 passthrough_bits);
> +	} else {
> +		ret = ipu_cpmem_set_image(priv->idmac_ch, &image);
> +		if (ret)
> +			return ret;
> +
> +		ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
> +	}
>   
>   	/*
>   	 * Set the channel for the direct CSI-->memory via SMFC
>
>

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

er, I meant I will integrate this patch. And verify/fix
possible breakage for non-bayer passthrough.

Steve


On 03/13/2017 02:30 AM, Russell King - ARM Linux wrote:
> On Mon, Mar 13, 2017 at 08:16:25AM +0000, Russell King - ARM Linux wrote:
>> On Sun, Mar 12, 2017 at 09:26:41PM -0700, Steve Longerbeam wrote:
>>> On 03/12/2017 01:22 PM, Russell King - ARM Linux wrote:
>>>> What I had was this patch for your v3.  I never got to testing your
>>>> v4 because of the LP-11 problem.
>>>>
>>>> In v5, you've changed to propagate the ipu_cpmem_set_image() error
>>>> code to avoid the resulting corruption, but that leaves the other bits
>>>> of this patch unaddressed, along my "media: imx: smfc: add support
>>>> for bayer formats" patch.
>>>>
>>>> Your driver basically has no support for bayer formats.
>>> You added the patches to this driver that adds the bayer support,
>>> I don't think there is anything more required of the driver at this
>>> point to support bayer, the remaining work needs to happen in the IPUv3
>>> driver.
>> There is more work, because the way you've merged my changes to
>> imx_smfc_setup_channel() into csi_idmac_setup_channel() is wrong with
>> respect to the burst size.
>>
>> You always set it to 8 or 16 depending on the width:
>>
>> 	burst_size = (image.pix.width & 0xf) ? 8 : 16;
>>
>> 	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
>>
>> and then you have my switch() statement which assigns burst_size.
>> My _tested_ code removed the above, added the switch, which had
>> a default case which reflected the above setting:
>>
>> 	default:
>> 		burst_size = (outfmt->width & 0xf) ? 8 : 16;
>>
>> and then went on to set the burst size _after_ the switch statement:
>>
>> 	ipu_cpmem_set_burstsize(priv->smfc_ch, burst_size);
>>
>> The effect is unchanged for non-bayer formats.  For bayer formats, the
>> burst size is determined by the bayer data size.
>>
>> So, even if it's appropriate to fix ipu_cpmem_set_image(), fixing the
>> above is still required.
>>
>> I'm not convinced that fixing ipu_cpmem_set_image() is even the best
>> solution - it's not as trivial as it looks on the surface:
>>
>>          ipu_cpmem_set_resolution(ch, image->rect.width, image->rect.height);
>>          ipu_cpmem_set_stride(ch, pix->bytesperline);
>>
>> this is fine, it doesn't depend on the format.  However, the next line:
>>
>>          ipu_cpmem_set_fmt(ch, v4l2_pix_fmt_to_drm_fourcc(pix->pixelformat));
>>
>> does - v4l2_pix_fmt_to_drm_fourcc() is a locally defined function (it
>> isn't v4l2 code) that converts a v4l2 pixel format to a DRM fourcc.
>> DRM knows nothing about bayer formats, there aren't fourcc codes in
>> DRM for it.  The result is that v4l2_pix_fmt_to_drm_fourcc() returns
>> -EINVAL cast to a u32, which gets passed unchecked into ipu_cpmem_set_fmt().
>>
>> ipu_cpmem_set_fmt() won't recognise that, and also returns -EINVAL - and
>> it's a bug that this is not checked and propagated.  If it is checked and
>> propagated, then we need this to support bayer formats, and I don't see
>> DRM people wanting bayer format fourcc codes added without there being
>> a real DRM driver wanting to use them.
>>
>> Then there's the business of calculating the top-left offset of the image,
>> which for bayer always needs to be an even number of pixels - as this
>> function takes the top-left offset, it ought to respect it, but if it
>> doesn't meet this criteria, what should it do?  csi_idmac_setup_channel()
>> always sets them to zero, but that's not really something that
>> ipu_cpmem_set_image() should assume.
> For the time being, I've restored the functionality along the same lines
> as I originally had.  This seems to get me working capture, but might
> break non-bayer passthrough mode:
>
> diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
> index fc0036aa84d0..df336971a009 100644
> --- a/drivers/staging/media/imx/imx-media-csi.c
> +++ b/drivers/staging/media/imx/imx-media-csi.c
> @@ -314,14 +314,6 @@ static int csi_idmac_setup_channel(struct csi_priv *priv)
>   	image.phys0 = phys[0];
>   	image.phys1 = phys[1];
>   
> -	ret = ipu_cpmem_set_image(priv->idmac_ch, &image);
> -	if (ret)
> -		return ret;
> -
> -	burst_size = (image.pix.width & 0xf) ? 8 : 16;
> -
> -	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
> -
>   	/*
>   	 * Check for conditions that require the IPU to handle the
>   	 * data internally as generic data, aka passthrough mode:
> @@ -346,15 +338,29 @@ static int csi_idmac_setup_channel(struct csi_priv *priv)
>   		passthrough_bits = 16;
>   		break;
>   	default:
> +		burst_size = (image.pix.width & 0xf) ? 8 : 16;
>   		passthrough = (sensor_ep->bus_type != V4L2_MBUS_CSI2 &&
>   			       sensor_ep->bus.parallel.bus_width >= 16);
>   		passthrough_bits = 16;
>   		break;
>   	}
>   
> -	if (passthrough)
> +	if (passthrough) {
> +		ipu_cpmem_set_resolution(priv->idmac_ch, image.rect.width,
> +					 image.rect.height);
> +		ipu_cpmem_set_stride(priv->idmac_ch, image.pix.bytesperline);
> +		ipu_cpmem_set_buffer(priv->idmac_ch, 0, image.phys0);
> +		ipu_cpmem_set_buffer(priv->idmac_ch, 1, image.phys1);
> +		ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
>   		ipu_cpmem_set_format_passthrough(priv->idmac_ch,
>   						 passthrough_bits);
> +	} else {
> +		ret = ipu_cpmem_set_image(priv->idmac_ch, &image);
> +		if (ret)
> +			return ret;
> +
> +		ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
> +	}
>   
>   	/*
>   	 * Set the channel for the direct CSI-->memory via SMFC
>
>

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/13/2017 01:16 AM, Russell King - ARM Linux wrote:
> On Sun, Mar 12, 2017 at 09:26:41PM -0700, Steve Longerbeam wrote:
>> On 03/12/2017 01:22 PM, Russell King - ARM Linux wrote:
>>> What I had was this patch for your v3.  I never got to testing your
>>> v4 because of the LP-11 problem.
>>>
>>> In v5, you've changed to propagate the ipu_cpmem_set_image() error
>>> code to avoid the resulting corruption, but that leaves the other bits
>>> of this patch unaddressed, along my "media: imx: smfc: add support
>>> for bayer formats" patch.
>>>
>>> Your driver basically has no support for bayer formats.
>> You added the patches to this driver that adds the bayer support,
>> I don't think there is anything more required of the driver at this
>> point to support bayer, the remaining work needs to happen in the IPUv3
>> driver.
> There is more work, because the way you've merged my changes to
> imx_smfc_setup_channel() into csi_idmac_setup_channel() is wrong with
> respect to the burst size.
>
> You always set it to 8 or 16 depending on the width:
>
> 	burst_size = (image.pix.width & 0xf) ? 8 : 16;
>
> 	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
>
> and then you have my switch() statement which assigns burst_size.
> My _tested_ code removed the above, added the switch, which had
> a default case which reflected the above setting:
>
> 	default:
> 		burst_size = (outfmt->width & 0xf) ? 8 : 16;
>
> and then went on to set the burst size _after_ the switch statement:
>
> 	ipu_cpmem_set_burstsize(priv->smfc_ch, burst_size);
>
> The effect is unchanged for non-bayer formats.  For bayer formats, the
> burst size is determined by the bayer data size.
>
> So, even if it's appropriate to fix ipu_cpmem_set_image(), fixing the
> above is still required.

Oops, sorry missed that. I'll fix.

>
> I'm not convinced that fixing ipu_cpmem_set_image() is even the best
> solution - it's not as trivial as it looks on the surface:
>
>          ipu_cpmem_set_resolution(ch, image->rect.width, image->rect.height);
>          ipu_cpmem_set_stride(ch, pix->bytesperline);
>
> this is fine, it doesn't depend on the format.  However, the next line:
>
>          ipu_cpmem_set_fmt(ch, v4l2_pix_fmt_to_drm_fourcc(pix->pixelformat));
>
> does - v4l2_pix_fmt_to_drm_fourcc() is a locally defined function (it
> isn't v4l2 code) that converts a v4l2 pixel format to a DRM fourcc.
> DRM knows nothing about bayer formats, there aren't fourcc codes in
> DRM for it.

right, yeah that's a problem.

>    The result is that v4l2_pix_fmt_to_drm_fourcc() returns
> -EINVAL cast to a u32, which gets passed unchecked into ipu_cpmem_set_fmt().

Ugh.

>
> ipu_cpmem_set_fmt() won't recognise that, and also returns -EINVAL - and
> it's a bug that this is not checked and propagated.  If it is checked and
> propagated, then we need this to support bayer formats, and I don't see
> DRM people wanting bayer format fourcc codes added without there being
> a real DRM driver wanting to use them.

true.

>
> Then there's the business of calculating the top-left offset of the image,
> which for bayer always needs to be an even number of pixels - as this
> function takes the top-left offset, it ought to respect it, but if it
> doesn't meet this criteria, what should it do?  csi_idmac_setup_channel()
> always sets them to zero, but that's not really something that
> ipu_cpmem_set_image() should assume.

Well, I will integrate your patch above. Thanks for doing this
work for me.

We do need to address the issues you brought up in ipu_cpmem at
some point.

Steve

[PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/13/2017 01:16 AM, Russell King - ARM Linux wrote:
> On Sun, Mar 12, 2017 at 09:26:41PM -0700, Steve Longerbeam wrote:
>> On 03/12/2017 01:22 PM, Russell King - ARM Linux wrote:
>>> What I had was this patch for your v3.  I never got to testing your
>>> v4 because of the LP-11 problem.
>>>
>>> In v5, you've changed to propagate the ipu_cpmem_set_image() error
>>> code to avoid the resulting corruption, but that leaves the other bits
>>> of this patch unaddressed, along my "media: imx: smfc: add support
>>> for bayer formats" patch.
>>>
>>> Your driver basically has no support for bayer formats.
>> You added the patches to this driver that adds the bayer support,
>> I don't think there is anything more required of the driver at this
>> point to support bayer, the remaining work needs to happen in the IPUv3
>> driver.
> There is more work, because the way you've merged my changes to
> imx_smfc_setup_channel() into csi_idmac_setup_channel() is wrong with
> respect to the burst size.
>
> You always set it to 8 or 16 depending on the width:
>
> 	burst_size = (image.pix.width & 0xf) ? 8 : 16;
>
> 	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
>
> and then you have my switch() statement which assigns burst_size.
> My _tested_ code removed the above, added the switch, which had
> a default case which reflected the above setting:
>
> 	default:
> 		burst_size = (outfmt->width & 0xf) ? 8 : 16;
>
> and then went on to set the burst size _after_ the switch statement:
>
> 	ipu_cpmem_set_burstsize(priv->smfc_ch, burst_size);
>
> The effect is unchanged for non-bayer formats.  For bayer formats, the
> burst size is determined by the bayer data size.
>
> So, even if it's appropriate to fix ipu_cpmem_set_image(), fixing the
> above is still required.

Oops, sorry missed that. I'll fix.

>
> I'm not convinced that fixing ipu_cpmem_set_image() is even the best
> solution - it's not as trivial as it looks on the surface:
>
>          ipu_cpmem_set_resolution(ch, image->rect.width, image->rect.height);
>          ipu_cpmem_set_stride(ch, pix->bytesperline);
>
> this is fine, it doesn't depend on the format.  However, the next line:
>
>          ipu_cpmem_set_fmt(ch, v4l2_pix_fmt_to_drm_fourcc(pix->pixelformat));
>
> does - v4l2_pix_fmt_to_drm_fourcc() is a locally defined function (it
> isn't v4l2 code) that converts a v4l2 pixel format to a DRM fourcc.
> DRM knows nothing about bayer formats, there aren't fourcc codes in
> DRM for it.

right, yeah that's a problem.

>    The result is that v4l2_pix_fmt_to_drm_fourcc() returns
> -EINVAL cast to a u32, which gets passed unchecked into ipu_cpmem_set_fmt().

Ugh.

>
> ipu_cpmem_set_fmt() won't recognise that, and also returns -EINVAL - and
> it's a bug that this is not checked and propagated.  If it is checked and
> propagated, then we need this to support bayer formats, and I don't see
> DRM people wanting bayer format fourcc codes added without there being
> a real DRM driver wanting to use them.

true.

>
> Then there's the business of calculating the top-left offset of the image,
> which for bayer always needs to be an even number of pixels - as this
> function takes the top-left offset, it ought to respect it, but if it
> doesn't meet this criteria, what should it do?  csi_idmac_setup_channel()
> always sets them to zero, but that's not really something that
> ipu_cpmem_set_image() should assume.

Well, I will integrate your patch above. Thanks for doing this
work for me.

We do need to address the issues you brought up in ipu_cpmem at
some point.

Steve

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/13/2017 01:16 AM, Russell King - ARM Linux wrote:
> On Sun, Mar 12, 2017 at 09:26:41PM -0700, Steve Longerbeam wrote:
>> On 03/12/2017 01:22 PM, Russell King - ARM Linux wrote:
>>> What I had was this patch for your v3.  I never got to testing your
>>> v4 because of the LP-11 problem.
>>>
>>> In v5, you've changed to propagate the ipu_cpmem_set_image() error
>>> code to avoid the resulting corruption, but that leaves the other bits
>>> of this patch unaddressed, along my "media: imx: smfc: add support
>>> for bayer formats" patch.
>>>
>>> Your driver basically has no support for bayer formats.
>> You added the patches to this driver that adds the bayer support,
>> I don't think there is anything more required of the driver at this
>> point to support bayer, the remaining work needs to happen in the IPUv3
>> driver.
> There is more work, because the way you've merged my changes to
> imx_smfc_setup_channel() into csi_idmac_setup_channel() is wrong with
> respect to the burst size.
>
> You always set it to 8 or 16 depending on the width:
>
> 	burst_size = (image.pix.width & 0xf) ? 8 : 16;
>
> 	ipu_cpmem_set_burstsize(priv->idmac_ch, burst_size);
>
> and then you have my switch() statement which assigns burst_size.
> My _tested_ code removed the above, added the switch, which had
> a default case which reflected the above setting:
>
> 	default:
> 		burst_size = (outfmt->width & 0xf) ? 8 : 16;
>
> and then went on to set the burst size _after_ the switch statement:
>
> 	ipu_cpmem_set_burstsize(priv->smfc_ch, burst_size);
>
> The effect is unchanged for non-bayer formats.  For bayer formats, the
> burst size is determined by the bayer data size.
>
> So, even if it's appropriate to fix ipu_cpmem_set_image(), fixing the
> above is still required.

Oops, sorry missed that. I'll fix.

>
> I'm not convinced that fixing ipu_cpmem_set_image() is even the best
> solution - it's not as trivial as it looks on the surface:
>
>          ipu_cpmem_set_resolution(ch, image->rect.width, image->rect.height);
>          ipu_cpmem_set_stride(ch, pix->bytesperline);
>
> this is fine, it doesn't depend on the format.  However, the next line:
>
>          ipu_cpmem_set_fmt(ch, v4l2_pix_fmt_to_drm_fourcc(pix->pixelformat));
>
> does - v4l2_pix_fmt_to_drm_fourcc() is a locally defined function (it
> isn't v4l2 code) that converts a v4l2 pixel format to a DRM fourcc.
> DRM knows nothing about bayer formats, there aren't fourcc codes in
> DRM for it.

right, yeah that's a problem.

>    The result is that v4l2_pix_fmt_to_drm_fourcc() returns
> -EINVAL cast to a u32, which gets passed unchecked into ipu_cpmem_set_fmt().

Ugh.

>
> ipu_cpmem_set_fmt() won't recognise that, and also returns -EINVAL - and
> it's a bug that this is not checked and propagated.  If it is checked and
> propagated, then we need this to support bayer formats, and I don't see
> DRM people wanting bayer format fourcc codes added without there being
> a real DRM driver wanting to use them.

true.

>
> Then there's the business of calculating the top-left offset of the image,
> which for bayer always needs to be an even number of pixels - as this
> function takes the top-left offset, it ought to respect it, but if it
> doesn't meet this criteria, what should it do?  csi_idmac_setup_channel()
> always sets them to zero, but that's not really something that
> ipu_cpmem_set_image() should assume.

Well, I will integrate your patch above. Thanks for doing this
work for me.

We do need to address the issues you brought up in ipu_cpmem at
some point.

Steve

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

I've just looked at my test system's dmesg, and spotted this in the log.
It's been a while since these popped out of the kernel, so I don't know
what caused them (other than the obvious, a media-ctl command.)

My script which sets this up only enables links, and then configures the
formats etc, and doesn't disable them, so I don't see why the power
count should be going negative.

------------[ cut here ]------------
WARNING: CPU: 1 PID: 1889 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0x9c/0xa8 [imx_media_csi]
Modules linked in: caam_jr uvcvideo snd_soc_imx_sgtl5000 snd_soc_fsl_asoc_card snd_soc_imx_spdif imx_media_csi(C) imx6_mipi_csi2(C) snd_soc_imx_audmux snd_soc_sgtl5000 imx219 imx_media_ic(C) imx_media_capture(C) imx_media_vdic(C) caam video_multiplexer imx_sdma coda v4l2_mem2mem videobuf2_v4l2 imx2_wdt imx_vdoa videobuf2_dma_contig videobuf2_core videobuf2_vmalloc videobuf2_memops snd_soc_fsl_ssi
imx_thermal snd_soc_fsl_spdif imx_pcm_dma imx_media(C) imx_media_common(C) nfsd
rc_pinnacle_pctv_hd dw_hdmi_ahb_audio dw_hdmi_cec etnaviv
CPU: 1 PID: 1889 Comm: media-ctl Tainted: G         C      4.11.0-rc1+ #2125
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Backtrace:
[<c0013ba4>] (dump_backtrace) from [<c0013de4>] (show_stack+0x18/0x1c)
 r6:600e0013 r5:ffffffff r4:00000000 r3:00000000
[<c0013dcc>] (show_stack) from [<c033f728>] (dump_stack+0xa4/0xdc)
[<c033f684>] (dump_stack) from [<c00326cc>] (__warn+0xdc/0x108)
 r6:bf124014 r5:00000000 r4:00000000 r3:c09ea4a8
[<c00325f0>] (__warn) from [<c0032720>] (warn_slowpath_null+0x28/0x30)
 r10:ede00010 r8:ede4a348 r7:d039501c r6:d0395140 r5:00000000 r4:d0395010
[<c00326f8>] (warn_slowpath_null) from [<bf1229e0>] (csi_s_power+0x9c/0xa8 [imx_media_csi])
[<bf122944>] (csi_s_power [imx_media_csi]) from [<bf04a930>] (imx_media_set_power+0x3c/0x108 [imx_media_common])
 r7:d039501c r6:00000000 r5:00000000 r4:0000000c
[<bf04a8f4>] (imx_media_set_power [imx_media_common]) from [<bf04aa34>] (imx_media_pipeline_set_power+0x38/0x40 [imx_media_common])
 r10:00000001 r9:00000001 r8:ede4a348 r7:ede00010 r6:ede4a348 r5:d039501c
 r4:00000001
[<bf04a9fc>] (imx_media_pipeline_set_power [imx_media_common]) from [<bf052148>] (imx_media_link_notify+0xf0/0x144 [imx_media])
 r7:ede00010 r6:ed59f900 r5:00000000 r4:d039501c
[<bf052058>] (imx_media_link_notify [imx_media]) from [<c04fa858>] (__media_entity_setup_link+0x110/0x1d8)
 r10:c0347c03 r9:d7eb3dc8 r8:befe92b0 r7:ede00010 r6:00000000 r5:00000001
 r4:ed59f900 r3:bf052058
[<c04fa748>] (__media_entity_setup_link) from [<c04f9bb0>] (media_device_setup_link+0x84/0x90)
 r7:ede00010 r6:ede00010 r5:ef3fd810 r4:d7eb3dc8
[<c04f9b2c>] (media_device_setup_link) from [<c04f9e94>] (media_device_ioctl+0xa4/0x148)
 r6:00000000 r5:d7eb3dc8 r4:c077b014 r3:c04f9b2c
[<c04f9df0>] (media_device_ioctl) from [<c04fa3a0>] (media_ioctl+0x38/0x4c)
 r10:ed5eca68 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:00000003 r5:e82ca280
 r4:c0190304
[<c04fa368>] (media_ioctl) from [<c018f9c0>] (do_vfs_ioctl+0x98/0x9a0)
[<c018f928>] (do_vfs_ioctl) from [<c0190304>] (SyS_ioctl+0x3c/0x60)
 r10:00000000 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:c0347c03 r5:e82ca280
 r4:e82ca280
[<c01902c8>] (SyS_ioctl) from [<c000fd60>] (ret_fast_syscall+0x0/0x1c)
 r8:c000ff04 r7:00000036 r6:000261d0 r5:00000001 r4:009162e8 r3:00000001
---[ end trace 4fdd40e5adfc4485 ]---
------------[ cut here ]------------
WARNING: CPU: 1 PID: 1889 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0x9c/0xa8 [imx_media_csi]
Modules linked in: caam_jr uvcvideo snd_soc_imx_sgtl5000 snd_soc_fsl_asoc_card snd_soc_imx_spdif imx_media_csi(C) imx6_mipi_csi2(C) snd_soc_imx_audmux snd_soc_sgtl5000 imx219 imx_media_ic(C) imx_media_capture(C) imx_media_vdic(C) caam video_multiplexer imx_sdma coda v4l2_mem2mem videobuf2_v4l2 imx2_wdt imx_vdoa videobuf2_dma_contig videobuf2_core videobuf2_vmalloc videobuf2_memops snd_soc_fsl_ssi
imx_thermal snd_soc_fsl_spdif imx_pcm_dma imx_media(C) imx_media_common(C) nfsd
rc_pinnacle_pctv_hd dw_hdmi_ahb_audio dw_hdmi_cec etnaviv
CPU: 1 PID: 1889 Comm: media-ctl Tainted: G        WC      4.11.0-rc1+ #2125
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Backtrace:
[<c0013ba4>] (dump_backtrace) from [<c0013de4>] (show_stack+0x18/0x1c)
 r6:600e0013 r5:ffffffff r4:00000000 r3:00000000
[<c0013dcc>] (show_stack) from [<c033f728>] (dump_stack+0xa4/0xdc)
[<c033f684>] (dump_stack) from [<c00326cc>] (__warn+0xdc/0x108)
 r6:bf124014 r5:00000000 r4:00000000 r3:c09ea4a8
[<c00325f0>] (__warn) from [<c0032720>] (warn_slowpath_null+0x28/0x30)
 r10:ede00010 r8:ede4a348 r7:ee000800 r6:d0395140 r5:00000000 r4:d0395010
[<c00326f8>] (warn_slowpath_null) from [<bf1229e0>] (csi_s_power+0x9c/0xa8 [imx_media_csi])
[<bf122944>] (csi_s_power [imx_media_csi]) from [<bf04a930>] (imx_media_set_power+0x3c/0x108 [imx_media_common])
 r7:ee000800 r6:00000000 r5:00000000 r4:0000000c
[<bf04a8f4>] (imx_media_set_power [imx_media_common]) from [<bf04aa34>] (imx_media_pipeline_set_power+0x38/0x40 [imx_media_common])
 r10:00000001 r9:00000001 r8:ede4a348 r7:ede00010 r6:ede4a348 r5:ee000800
 r4:00000001
[<bf04a9fc>] (imx_media_pipeline_set_power [imx_media_common]) from [<bf052148>] (imx_media_link_notify+0xf0/0x144 [imx_media])
 r7:ede00010 r6:d0320480 r5:ee000800 r4:ee000800
[<bf052058>] (imx_media_link_notify [imx_media]) from [<c04fa858>] (__media_entity_setup_link+0x110/0x1d8)
 r10:c0347c03 r9:d7eb3dc8 r8:befe92b0 r7:ede00010 r6:00000000 r5:00000001
 r4:d0320480 r3:bf052058
[<c04fa748>] (__media_entity_setup_link) from [<c04f9bb0>] (media_device_setup_link+0x84/0x90)
 r7:ede00010 r6:ede00010 r5:d039501c r4:d7eb3dc8
[<c04f9b2c>] (media_device_setup_link) from [<c04f9e94>] (media_device_ioctl+0xa4/0x148)
 r6:00000000 r5:d7eb3dc8 r4:c077b014 r3:c04f9b2c
[<c04f9df0>] (media_device_ioctl) from [<c04fa3a0>] (media_ioctl+0x38/0x4c)
 r10:ed5eca68 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:00000003 r5:e82ca500
 r4:c0190304
[<c04fa368>] (media_ioctl) from [<c018f9c0>] (do_vfs_ioctl+0x98/0x9a0)
[<c018f928>] (do_vfs_ioctl) from [<c0190304>] (SyS_ioctl+0x3c/0x60)
 r10:00000000 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:c0347c03 r5:e82ca500
 r4:e82ca500
[<c01902c8>] (SyS_ioctl) from [<c000fd60>] (ret_fast_syscall+0x0/0x1c)
 r8:c000ff04 r7:00000036 r6:000261d0 r5:00000001 r4:0091737c r3:00000001
---[ end trace 4fdd40e5adfc4486 ]---

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

I've just looked at my test system's dmesg, and spotted this in the log.
It's been a while since these popped out of the kernel, so I don't know
what caused them (other than the obvious, a media-ctl command.)

My script which sets this up only enables links, and then configures the
formats etc, and doesn't disable them, so I don't see why the power
count should be going negative.

------------[ cut here ]------------
WARNING: CPU: 1 PID: 1889 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0x9c/0xa8 [imx_media_csi]
Modules linked in: caam_jr uvcvideo snd_soc_imx_sgtl5000 snd_soc_fsl_asoc_card snd_soc_imx_spdif imx_media_csi(C) imx6_mipi_csi2(C) snd_soc_imx_audmux snd_soc_sgtl5000 imx219 imx_media_ic(C) imx_media_capture(C) imx_media_vdic(C) caam video_multiplexer imx_sdma coda v4l2_mem2mem videobuf2_v4l2 imx2_wdt imx_vdoa videobuf2_dma_contig videobuf2_core videobuf2_vmalloc videobuf2_memops snd_soc_fsl_ssi
imx_thermal snd_soc_fsl_spdif imx_pcm_dma imx_media(C) imx_media_common(C) nfsd
rc_pinnacle_pctv_hd dw_hdmi_ahb_audio dw_hdmi_cec etnaviv
CPU: 1 PID: 1889 Comm: media-ctl Tainted: G         C      4.11.0-rc1+ #2125
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Backtrace:
[<c0013ba4>] (dump_backtrace) from [<c0013de4>] (show_stack+0x18/0x1c)
 r6:600e0013 r5:ffffffff r4:00000000 r3:00000000
[<c0013dcc>] (show_stack) from [<c033f728>] (dump_stack+0xa4/0xdc)
[<c033f684>] (dump_stack) from [<c00326cc>] (__warn+0xdc/0x108)
 r6:bf124014 r5:00000000 r4:00000000 r3:c09ea4a8
[<c00325f0>] (__warn) from [<c0032720>] (warn_slowpath_null+0x28/0x30)
 r10:ede00010 r8:ede4a348 r7:d039501c r6:d0395140 r5:00000000 r4:d0395010
[<c00326f8>] (warn_slowpath_null) from [<bf1229e0>] (csi_s_power+0x9c/0xa8 [imx_media_csi])
[<bf122944>] (csi_s_power [imx_media_csi]) from [<bf04a930>] (imx_media_set_power+0x3c/0x108 [imx_media_common])
 r7:d039501c r6:00000000 r5:00000000 r4:0000000c
[<bf04a8f4>] (imx_media_set_power [imx_media_common]) from [<bf04aa34>] (imx_media_pipeline_set_power+0x38/0x40 [imx_media_common])
 r10:00000001 r9:00000001 r8:ede4a348 r7:ede00010 r6:ede4a348 r5:d039501c
 r4:00000001
[<bf04a9fc>] (imx_media_pipeline_set_power [imx_media_common]) from [<bf052148>] (imx_media_link_notify+0xf0/0x144 [imx_media])
 r7:ede00010 r6:ed59f900 r5:00000000 r4:d039501c
[<bf052058>] (imx_media_link_notify [imx_media]) from [<c04fa858>] (__media_entity_setup_link+0x110/0x1d8)
 r10:c0347c03 r9:d7eb3dc8 r8:befe92b0 r7:ede00010 r6:00000000 r5:00000001
 r4:ed59f900 r3:bf052058
[<c04fa748>] (__media_entity_setup_link) from [<c04f9bb0>] (media_device_setup_link+0x84/0x90)
 r7:ede00010 r6:ede00010 r5:ef3fd810 r4:d7eb3dc8
[<c04f9b2c>] (media_device_setup_link) from [<c04f9e94>] (media_device_ioctl+0xa4/0x148)
 r6:00000000 r5:d7eb3dc8 r4:c077b014 r3:c04f9b2c
[<c04f9df0>] (media_device_ioctl) from [<c04fa3a0>] (media_ioctl+0x38/0x4c)
 r10:ed5eca68 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:00000003 r5:e82ca280
 r4:c0190304
[<c04fa368>] (media_ioctl) from [<c018f9c0>] (do_vfs_ioctl+0x98/0x9a0)
[<c018f928>] (do_vfs_ioctl) from [<c0190304>] (SyS_ioctl+0x3c/0x60)
 r10:00000000 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:c0347c03 r5:e82ca280
 r4:e82ca280
[<c01902c8>] (SyS_ioctl) from [<c000fd60>] (ret_fast_syscall+0x0/0x1c)
 r8:c000ff04 r7:00000036 r6:000261d0 r5:00000001 r4:009162e8 r3:00000001
---[ end trace 4fdd40e5adfc4485 ]---
------------[ cut here ]------------
WARNING: CPU: 1 PID: 1889 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0x9c/0xa8 [imx_media_csi]
Modules linked in: caam_jr uvcvideo snd_soc_imx_sgtl5000 snd_soc_fsl_asoc_card snd_soc_imx_spdif imx_media_csi(C) imx6_mipi_csi2(C) snd_soc_imx_audmux snd_soc_sgtl5000 imx219 imx_media_ic(C) imx_media_capture(C) imx_media_vdic(C) caam video_multiplexer imx_sdma coda v4l2_mem2mem videobuf2_v4l2 imx2_wdt imx_vdoa videobuf2_dma_contig videobuf2_core videobuf2_vmalloc videobuf2_memops snd_soc_fsl_ssi
imx_thermal snd_soc_fsl_spdif imx_pcm_dma imx_media(C) imx_media_common(C) nfsd
rc_pinnacle_pctv_hd dw_hdmi_ahb_audio dw_hdmi_cec etnaviv
CPU: 1 PID: 1889 Comm: media-ctl Tainted: G        WC      4.11.0-rc1+ #2125
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Backtrace:
[<c0013ba4>] (dump_backtrace) from [<c0013de4>] (show_stack+0x18/0x1c)
 r6:600e0013 r5:ffffffff r4:00000000 r3:00000000
[<c0013dcc>] (show_stack) from [<c033f728>] (dump_stack+0xa4/0xdc)
[<c033f684>] (dump_stack) from [<c00326cc>] (__warn+0xdc/0x108)
 r6:bf124014 r5:00000000 r4:00000000 r3:c09ea4a8
[<c00325f0>] (__warn) from [<c0032720>] (warn_slowpath_null+0x28/0x30)
 r10:ede00010 r8:ede4a348 r7:ee000800 r6:d0395140 r5:00000000 r4:d0395010
[<c00326f8>] (warn_slowpath_null) from [<bf1229e0>] (csi_s_power+0x9c/0xa8 [imx_media_csi])
[<bf122944>] (csi_s_power [imx_media_csi]) from [<bf04a930>] (imx_media_set_power+0x3c/0x108 [imx_media_common])
 r7:ee000800 r6:00000000 r5:00000000 r4:0000000c
[<bf04a8f4>] (imx_media_set_power [imx_media_common]) from [<bf04aa34>] (imx_media_pipeline_set_power+0x38/0x40 [imx_media_common])
 r10:00000001 r9:00000001 r8:ede4a348 r7:ede00010 r6:ede4a348 r5:ee000800
 r4:00000001
[<bf04a9fc>] (imx_media_pipeline_set_power [imx_media_common]) from [<bf052148>] (imx_media_link_notify+0xf0/0x144 [imx_media])
 r7:ede00010 r6:d0320480 r5:ee000800 r4:ee000800
[<bf052058>] (imx_media_link_notify [imx_media]) from [<c04fa858>] (__media_entity_setup_link+0x110/0x1d8)
 r10:c0347c03 r9:d7eb3dc8 r8:befe92b0 r7:ede00010 r6:00000000 r5:00000001
 r4:d0320480 r3:bf052058
[<c04fa748>] (__media_entity_setup_link) from [<c04f9bb0>] (media_device_setup_link+0x84/0x90)
 r7:ede00010 r6:ede00010 r5:d039501c r4:d7eb3dc8
[<c04f9b2c>] (media_device_setup_link) from [<c04f9e94>] (media_device_ioctl+0xa4/0x148)
 r6:00000000 r5:d7eb3dc8 r4:c077b014 r3:c04f9b2c
[<c04f9df0>] (media_device_ioctl) from [<c04fa3a0>] (media_ioctl+0x38/0x4c)
 r10:ed5eca68 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:00000003 r5:e82ca500
 r4:c0190304
[<c04fa368>] (media_ioctl) from [<c018f9c0>] (do_vfs_ioctl+0x98/0x9a0)
[<c018f928>] (do_vfs_ioctl) from [<c0190304>] (SyS_ioctl+0x3c/0x60)
 r10:00000000 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:c0347c03 r5:e82ca500
 r4:e82ca500
[<c01902c8>] (SyS_ioctl) from [<c000fd60>] (ret_fast_syscall+0x0/0x1c)
 r8:c000ff04 r7:00000036 r6:000261d0 r5:00000001 r4:0091737c r3:00000001
---[ end trace 4fdd40e5adfc4486 ]---

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

I've just looked at my test system's dmesg, and spotted this in the log.
It's been a while since these popped out of the kernel, so I don't know
what caused them (other than the obvious, a media-ctl command.)

My script which sets this up only enables links, and then configures the
formats etc, and doesn't disable them, so I don't see why the power
count should be going negative.

------------[ cut here ]------------
WARNING: CPU: 1 PID: 1889 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0x9c/0xa8 [imx_media_csi]
Modules linked in: caam_jr uvcvideo snd_soc_imx_sgtl5000 snd_soc_fsl_asoc_card snd_soc_imx_spdif imx_media_csi(C) imx6_mipi_csi2(C) snd_soc_imx_audmux snd_soc_sgtl5000 imx219 imx_media_ic(C) imx_media_capture(C) imx_media_vdic(C) caam video_multiplexer imx_sdma coda v4l2_mem2mem videobuf2_v4l2 imx2_wdt imx_vdoa videobuf2_dma_contig videobuf2_core videobuf2_vmalloc videobuf2_memops snd_soc_fsl_ssi
imx_thermal snd_soc_fsl_spdif imx_pcm_dma imx_media(C) imx_media_common(C) nfsd
rc_pinnacle_pctv_hd dw_hdmi_ahb_audio dw_hdmi_cec etnaviv
CPU: 1 PID: 1889 Comm: media-ctl Tainted: G         C      4.11.0-rc1+ #2125
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Backtrace:
[<c0013ba4>] (dump_backtrace) from [<c0013de4>] (show_stack+0x18/0x1c)
 r6:600e0013 r5:ffffffff r4:00000000 r3:00000000
[<c0013dcc>] (show_stack) from [<c033f728>] (dump_stack+0xa4/0xdc)
[<c033f684>] (dump_stack) from [<c00326cc>] (__warn+0xdc/0x108)
 r6:bf124014 r5:00000000 r4:00000000 r3:c09ea4a8
[<c00325f0>] (__warn) from [<c0032720>] (warn_slowpath_null+0x28/0x30)
 r10:ede00010 r8:ede4a348 r7:d039501c r6:d0395140 r5:00000000 r4:d0395010
[<c00326f8>] (warn_slowpath_null) from [<bf1229e0>] (csi_s_power+0x9c/0xa8 [imx_media_csi])
[<bf122944>] (csi_s_power [imx_media_csi]) from [<bf04a930>] (imx_media_set_power+0x3c/0x108 [imx_media_common])
 r7:d039501c r6:00000000 r5:00000000 r4:0000000c
[<bf04a8f4>] (imx_media_set_power [imx_media_common]) from [<bf04aa34>] (imx_media_pipeline_set_power+0x38/0x40 [imx_media_common])
 r10:00000001 r9:00000001 r8:ede4a348 r7:ede00010 r6:ede4a348 r5:d039501c
 r4:00000001
[<bf04a9fc>] (imx_media_pipeline_set_power [imx_media_common]) from [<bf052148>] (imx_media_link_notify+0xf0/0x144 [imx_media])
 r7:ede00010 r6:ed59f900 r5:00000000 r4:d039501c
[<bf052058>] (imx_media_link_notify [imx_media]) from [<c04fa858>] (__media_entity_setup_link+0x110/0x1d8)
 r10:c0347c03 r9:d7eb3dc8 r8:befe92b0 r7:ede00010 r6:00000000 r5:00000001
 r4:ed59f900 r3:bf052058
[<c04fa748>] (__media_entity_setup_link) from [<c04f9bb0>] (media_device_setup_link+0x84/0x90)
 r7:ede00010 r6:ede00010 r5:ef3fd810 r4:d7eb3dc8
[<c04f9b2c>] (media_device_setup_link) from [<c04f9e94>] (media_device_ioctl+0xa4/0x148)
 r6:00000000 r5:d7eb3dc8 r4:c077b014 r3:c04f9b2c
[<c04f9df0>] (media_device_ioctl) from [<c04fa3a0>] (media_ioctl+0x38/0x4c)
 r10:ed5eca68 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:00000003 r5:e82ca280
 r4:c0190304
[<c04fa368>] (media_ioctl) from [<c018f9c0>] (do_vfs_ioctl+0x98/0x9a0)
[<c018f928>] (do_vfs_ioctl) from [<c0190304>] (SyS_ioctl+0x3c/0x60)
 r10:00000000 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:c0347c03 r5:e82ca280
 r4:e82ca280
[<c01902c8>] (SyS_ioctl) from [<c000fd60>] (ret_fast_syscall+0x0/0x1c)
 r8:c000ff04 r7:00000036 r6:000261d0 r5:00000001 r4:009162e8 r3:00000001
---[ end trace 4fdd40e5adfc4485 ]---
------------[ cut here ]------------
WARNING: CPU: 1 PID: 1889 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0x9c/0xa8 [imx_media_csi]
Modules linked in: caam_jr uvcvideo snd_soc_imx_sgtl5000 snd_soc_fsl_asoc_card snd_soc_imx_spdif imx_media_csi(C) imx6_mipi_csi2(C) snd_soc_imx_audmux snd_soc_sgtl5000 imx219 imx_media_ic(C) imx_media_capture(C) imx_media_vdic(C) caam video_multiplexer imx_sdma coda v4l2_mem2mem videobuf2_v4l2 imx2_wdt imx_vdoa videobuf2_dma_contig videobuf2_core videobuf2_vmalloc videobuf2_memops snd_soc_fsl_ssi
imx_thermal snd_soc_fsl_spdif imx_pcm_dma imx_media(C) imx_media_common(C) nfsd
rc_pinnacle_pctv_hd dw_hdmi_ahb_audio dw_hdmi_cec etnaviv
CPU: 1 PID: 1889 Comm: media-ctl Tainted: G        WC      4.11.0-rc1+ #2125
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Backtrace:
[<c0013ba4>] (dump_backtrace) from [<c0013de4>] (show_stack+0x18/0x1c)
 r6:600e0013 r5:ffffffff r4:00000000 r3:00000000
[<c0013dcc>] (show_stack) from [<c033f728>] (dump_stack+0xa4/0xdc)
[<c033f684>] (dump_stack) from [<c00326cc>] (__warn+0xdc/0x108)
 r6:bf124014 r5:00000000 r4:00000000 r3:c09ea4a8
[<c00325f0>] (__warn) from [<c0032720>] (warn_slowpath_null+0x28/0x30)
 r10:ede00010 r8:ede4a348 r7:ee000800 r6:d0395140 r5:00000000 r4:d0395010
[<c00326f8>] (warn_slowpath_null) from [<bf1229e0>] (csi_s_power+0x9c/0xa8 [imx_media_csi])
[<bf122944>] (csi_s_power [imx_media_csi]) from [<bf04a930>] (imx_media_set_power+0x3c/0x108 [imx_media_common])
 r7:ee000800 r6:00000000 r5:00000000 r4:0000000c
[<bf04a8f4>] (imx_media_set_power [imx_media_common]) from [<bf04aa34>] (imx_media_pipeline_set_power+0x38/0x40 [imx_media_common])
 r10:00000001 r9:00000001 r8:ede4a348 r7:ede00010 r6:ede4a348 r5:ee000800
 r4:00000001
[<bf04a9fc>] (imx_media_pipeline_set_power [imx_media_common]) from [<bf052148>] (imx_media_link_notify+0xf0/0x144 [imx_media])
 r7:ede00010 r6:d0320480 r5:ee000800 r4:ee000800
[<bf052058>] (imx_media_link_notify [imx_media]) from [<c04fa858>] (__media_entity_setup_link+0x110/0x1d8)
 r10:c0347c03 r9:d7eb3dc8 r8:befe92b0 r7:ede00010 r6:00000000 r5:00000001
 r4:d0320480 r3:bf052058
[<c04fa748>] (__media_entity_setup_link) from [<c04f9bb0>] (media_device_setup_link+0x84/0x90)
 r7:ede00010 r6:ede00010 r5:d039501c r4:d7eb3dc8
[<c04f9b2c>] (media_device_setup_link) from [<c04f9e94>] (media_device_ioctl+0xa4/0x148)
 r6:00000000 r5:d7eb3dc8 r4:c077b014 r3:c04f9b2c
[<c04f9df0>] (media_device_ioctl) from [<c04fa3a0>] (media_ioctl+0x38/0x4c)
 r10:ed5eca68 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:00000003 r5:e82ca500
 r4:c0190304
[<c04fa368>] (media_ioctl) from [<c018f9c0>] (do_vfs_ioctl+0x98/0x9a0)
[<c018f928>] (do_vfs_ioctl) from [<c0190304>] (SyS_ioctl+0x3c/0x60)
 r10:00000000 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:c0347c03 r5:e82ca500
 r4:e82ca500
[<c01902c8>] (SyS_ioctl) from [<c000fd60>] (ret_fast_syscall+0x0/0x1c)
 r8:c000ff04 r7:00000036 r6:000261d0 r5:00000001 r4:0091737c r3:00000001
---[ end trace 4fdd40e5adfc4486 ]---

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 10:51 AM, Russell King - ARM Linux wrote:
> I've just looked at my test system's dmesg, and spotted this in the log.
> It's been a while since these popped out of the kernel, so I don't know
> what caused them (other than the obvious, a media-ctl command.)
>
> My script which sets this up only enables links, and then configures the
> formats etc, and doesn't disable them, so I don't see why the power
> count should be going negative.

There's actually nothing preventing userland from disabling a link
multiple times, and imx_media_link_notify() complies, and so
csi_s_power(OFF) gets called multiple times, and so that WARN_ON()
in there is silly, I borrowed this from other MC driver examples,
but it makes no sense to me, I'll remove it and prevent the power
count from going negative.

Steve



>
> ------------[ cut here ]------------
> WARNING: CPU: 1 PID: 1889 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0x9c/0xa8 [imx_media_csi]
> Modules linked in: caam_jr uvcvideo snd_soc_imx_sgtl5000 snd_soc_fsl_asoc_card snd_soc_imx_spdif imx_media_csi(C) imx6_mipi_csi2(C) snd_soc_imx_audmux snd_soc_sgtl5000 imx219 imx_media_ic(C) imx_media_capture(C) imx_media_vdic(C) caam video_multiplexer imx_sdma coda v4l2_mem2mem videobuf2_v4l2 imx2_wdt imx_vdoa videobuf2_dma_contig videobuf2_core videobuf2_vmalloc videobuf2_memops snd_soc_fsl_ssi
> imx_thermal snd_soc_fsl_spdif imx_pcm_dma imx_media(C) imx_media_common(C) nfsd
> rc_pinnacle_pctv_hd dw_hdmi_ahb_audio dw_hdmi_cec etnaviv
> CPU: 1 PID: 1889 Comm: media-ctl Tainted: G         C      4.11.0-rc1+ #2125
> Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
> Backtrace:
> [<c0013ba4>] (dump_backtrace) from [<c0013de4>] (show_stack+0x18/0x1c)
>  r6:600e0013 r5:ffffffff r4:00000000 r3:00000000
> [<c0013dcc>] (show_stack) from [<c033f728>] (dump_stack+0xa4/0xdc)
> [<c033f684>] (dump_stack) from [<c00326cc>] (__warn+0xdc/0x108)
>  r6:bf124014 r5:00000000 r4:00000000 r3:c09ea4a8
> [<c00325f0>] (__warn) from [<c0032720>] (warn_slowpath_null+0x28/0x30)
>  r10:ede00010 r8:ede4a348 r7:d039501c r6:d0395140 r5:00000000 r4:d0395010
> [<c00326f8>] (warn_slowpath_null) from [<bf1229e0>] (csi_s_power+0x9c/0xa8 [imx_media_csi])
> [<bf122944>] (csi_s_power [imx_media_csi]) from [<bf04a930>] (imx_media_set_power+0x3c/0x108 [imx_media_common])
>  r7:d039501c r6:00000000 r5:00000000 r4:0000000c
> [<bf04a8f4>] (imx_media_set_power [imx_media_common]) from [<bf04aa34>] (imx_media_pipeline_set_power+0x38/0x40 [imx_media_common])
>  r10:00000001 r9:00000001 r8:ede4a348 r7:ede00010 r6:ede4a348 r5:d039501c
>  r4:00000001
> [<bf04a9fc>] (imx_media_pipeline_set_power [imx_media_common]) from [<bf052148>] (imx_media_link_notify+0xf0/0x144 [imx_media])
>  r7:ede00010 r6:ed59f900 r5:00000000 r4:d039501c
> [<bf052058>] (imx_media_link_notify [imx_media]) from [<c04fa858>] (__media_entity_setup_link+0x110/0x1d8)
>  r10:c0347c03 r9:d7eb3dc8 r8:befe92b0 r7:ede00010 r6:00000000 r5:00000001
>  r4:ed59f900 r3:bf052058
> [<c04fa748>] (__media_entity_setup_link) from [<c04f9bb0>] (media_device_setup_link+0x84/0x90)
>  r7:ede00010 r6:ede00010 r5:ef3fd810 r4:d7eb3dc8
> [<c04f9b2c>] (media_device_setup_link) from [<c04f9e94>] (media_device_ioctl+0xa4/0x148)
>  r6:00000000 r5:d7eb3dc8 r4:c077b014 r3:c04f9b2c
> [<c04f9df0>] (media_device_ioctl) from [<c04fa3a0>] (media_ioctl+0x38/0x4c)
>  r10:ed5eca68 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:00000003 r5:e82ca280
>  r4:c0190304
> [<c04fa368>] (media_ioctl) from [<c018f9c0>] (do_vfs_ioctl+0x98/0x9a0)
> [<c018f928>] (do_vfs_ioctl) from [<c0190304>] (SyS_ioctl+0x3c/0x60)
>  r10:00000000 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:c0347c03 r5:e82ca280
>  r4:e82ca280
> [<c01902c8>] (SyS_ioctl) from [<c000fd60>] (ret_fast_syscall+0x0/0x1c)
>  r8:c000ff04 r7:00000036 r6:000261d0 r5:00000001 r4:009162e8 r3:00000001
> ---[ end trace 4fdd40e5adfc4485 ]---
> ------------[ cut here ]------------
> WARNING: CPU: 1 PID: 1889 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0x9c/0xa8 [imx_media_csi]
> Modules linked in: caam_jr uvcvideo snd_soc_imx_sgtl5000 snd_soc_fsl_asoc_card snd_soc_imx_spdif imx_media_csi(C) imx6_mipi_csi2(C) snd_soc_imx_audmux snd_soc_sgtl5000 imx219 imx_media_ic(C) imx_media_capture(C) imx_media_vdic(C) caam video_multiplexer imx_sdma coda v4l2_mem2mem videobuf2_v4l2 imx2_wdt imx_vdoa videobuf2_dma_contig videobuf2_core videobuf2_vmalloc videobuf2_memops snd_soc_fsl_ssi
> imx_thermal snd_soc_fsl_spdif imx_pcm_dma imx_media(C) imx_media_common(C) nfsd
> rc_pinnacle_pctv_hd dw_hdmi_ahb_audio dw_hdmi_cec etnaviv
> CPU: 1 PID: 1889 Comm: media-ctl Tainted: G        WC      4.11.0-rc1+ #2125
> Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
> Backtrace:
> [<c0013ba4>] (dump_backtrace) from [<c0013de4>] (show_stack+0x18/0x1c)
>  r6:600e0013 r5:ffffffff r4:00000000 r3:00000000
> [<c0013dcc>] (show_stack) from [<c033f728>] (dump_stack+0xa4/0xdc)
> [<c033f684>] (dump_stack) from [<c00326cc>] (__warn+0xdc/0x108)
>  r6:bf124014 r5:00000000 r4:00000000 r3:c09ea4a8
> [<c00325f0>] (__warn) from [<c0032720>] (warn_slowpath_null+0x28/0x30)
>  r10:ede00010 r8:ede4a348 r7:ee000800 r6:d0395140 r5:00000000 r4:d0395010
> [<c00326f8>] (warn_slowpath_null) from [<bf1229e0>] (csi_s_power+0x9c/0xa8 [imx_media_csi])
> [<bf122944>] (csi_s_power [imx_media_csi]) from [<bf04a930>] (imx_media_set_power+0x3c/0x108 [imx_media_common])
>  r7:ee000800 r6:00000000 r5:00000000 r4:0000000c
> [<bf04a8f4>] (imx_media_set_power [imx_media_common]) from [<bf04aa34>] (imx_media_pipeline_set_power+0x38/0x40 [imx_media_common])
>  r10:00000001 r9:00000001 r8:ede4a348 r7:ede00010 r6:ede4a348 r5:ee000800
>  r4:00000001
> [<bf04a9fc>] (imx_media_pipeline_set_power [imx_media_common]) from [<bf052148>] (imx_media_link_notify+0xf0/0x144 [imx_media])
>  r7:ede00010 r6:d0320480 r5:ee000800 r4:ee000800
> [<bf052058>] (imx_media_link_notify [imx_media]) from [<c04fa858>] (__media_entity_setup_link+0x110/0x1d8)
>  r10:c0347c03 r9:d7eb3dc8 r8:befe92b0 r7:ede00010 r6:00000000 r5:00000001
>  r4:d0320480 r3:bf052058
> [<c04fa748>] (__media_entity_setup_link) from [<c04f9bb0>] (media_device_setup_link+0x84/0x90)
>  r7:ede00010 r6:ede00010 r5:d039501c r4:d7eb3dc8
> [<c04f9b2c>] (media_device_setup_link) from [<c04f9e94>] (media_device_ioctl+0xa4/0x148)
>  r6:00000000 r5:d7eb3dc8 r4:c077b014 r3:c04f9b2c
> [<c04f9df0>] (media_device_ioctl) from [<c04fa3a0>] (media_ioctl+0x38/0x4c)
>  r10:ed5eca68 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:00000003 r5:e82ca500
>  r4:c0190304
> [<c04fa368>] (media_ioctl) from [<c018f9c0>] (do_vfs_ioctl+0x98/0x9a0)
> [<c018f928>] (do_vfs_ioctl) from [<c0190304>] (SyS_ioctl+0x3c/0x60)
>  r10:00000000 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:c0347c03 r5:e82ca500
>  r4:e82ca500
> [<c01902c8>] (SyS_ioctl) from [<c000fd60>] (ret_fast_syscall+0x0/0x1c)
>  r8:c000ff04 r7:00000036 r6:000261d0 r5:00000001 r4:0091737c r3:00000001
> ---[ end trace 4fdd40e5adfc4486 ]---
>

[PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 10:51 AM, Russell King - ARM Linux wrote:
> I've just looked at my test system's dmesg, and spotted this in the log.
> It's been a while since these popped out of the kernel, so I don't know
> what caused them (other than the obvious, a media-ctl command.)
>
> My script which sets this up only enables links, and then configures the
> formats etc, and doesn't disable them, so I don't see why the power
> count should be going negative.

There's actually nothing preventing userland from disabling a link
multiple times, and imx_media_link_notify() complies, and so
csi_s_power(OFF) gets called multiple times, and so that WARN_ON()
in there is silly, I borrowed this from other MC driver examples,
but it makes no sense to me, I'll remove it and prevent the power
count from going negative.

Steve



>
> ------------[ cut here ]------------
> WARNING: CPU: 1 PID: 1889 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0x9c/0xa8 [imx_media_csi]
> Modules linked in: caam_jr uvcvideo snd_soc_imx_sgtl5000 snd_soc_fsl_asoc_card snd_soc_imx_spdif imx_media_csi(C) imx6_mipi_csi2(C) snd_soc_imx_audmux snd_soc_sgtl5000 imx219 imx_media_ic(C) imx_media_capture(C) imx_media_vdic(C) caam video_multiplexer imx_sdma coda v4l2_mem2mem videobuf2_v4l2 imx2_wdt imx_vdoa videobuf2_dma_contig videobuf2_core videobuf2_vmalloc videobuf2_memops snd_soc_fsl_ssi
> imx_thermal snd_soc_fsl_spdif imx_pcm_dma imx_media(C) imx_media_common(C) nfsd
> rc_pinnacle_pctv_hd dw_hdmi_ahb_audio dw_hdmi_cec etnaviv
> CPU: 1 PID: 1889 Comm: media-ctl Tainted: G         C      4.11.0-rc1+ #2125
> Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
> Backtrace:
> [<c0013ba4>] (dump_backtrace) from [<c0013de4>] (show_stack+0x18/0x1c)
>  r6:600e0013 r5:ffffffff r4:00000000 r3:00000000
> [<c0013dcc>] (show_stack) from [<c033f728>] (dump_stack+0xa4/0xdc)
> [<c033f684>] (dump_stack) from [<c00326cc>] (__warn+0xdc/0x108)
>  r6:bf124014 r5:00000000 r4:00000000 r3:c09ea4a8
> [<c00325f0>] (__warn) from [<c0032720>] (warn_slowpath_null+0x28/0x30)
>  r10:ede00010 r8:ede4a348 r7:d039501c r6:d0395140 r5:00000000 r4:d0395010
> [<c00326f8>] (warn_slowpath_null) from [<bf1229e0>] (csi_s_power+0x9c/0xa8 [imx_media_csi])
> [<bf122944>] (csi_s_power [imx_media_csi]) from [<bf04a930>] (imx_media_set_power+0x3c/0x108 [imx_media_common])
>  r7:d039501c r6:00000000 r5:00000000 r4:0000000c
> [<bf04a8f4>] (imx_media_set_power [imx_media_common]) from [<bf04aa34>] (imx_media_pipeline_set_power+0x38/0x40 [imx_media_common])
>  r10:00000001 r9:00000001 r8:ede4a348 r7:ede00010 r6:ede4a348 r5:d039501c
>  r4:00000001
> [<bf04a9fc>] (imx_media_pipeline_set_power [imx_media_common]) from [<bf052148>] (imx_media_link_notify+0xf0/0x144 [imx_media])
>  r7:ede00010 r6:ed59f900 r5:00000000 r4:d039501c
> [<bf052058>] (imx_media_link_notify [imx_media]) from [<c04fa858>] (__media_entity_setup_link+0x110/0x1d8)
>  r10:c0347c03 r9:d7eb3dc8 r8:befe92b0 r7:ede00010 r6:00000000 r5:00000001
>  r4:ed59f900 r3:bf052058
> [<c04fa748>] (__media_entity_setup_link) from [<c04f9bb0>] (media_device_setup_link+0x84/0x90)
>  r7:ede00010 r6:ede00010 r5:ef3fd810 r4:d7eb3dc8
> [<c04f9b2c>] (media_device_setup_link) from [<c04f9e94>] (media_device_ioctl+0xa4/0x148)
>  r6:00000000 r5:d7eb3dc8 r4:c077b014 r3:c04f9b2c
> [<c04f9df0>] (media_device_ioctl) from [<c04fa3a0>] (media_ioctl+0x38/0x4c)
>  r10:ed5eca68 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:00000003 r5:e82ca280
>  r4:c0190304
> [<c04fa368>] (media_ioctl) from [<c018f9c0>] (do_vfs_ioctl+0x98/0x9a0)
> [<c018f928>] (do_vfs_ioctl) from [<c0190304>] (SyS_ioctl+0x3c/0x60)
>  r10:00000000 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:c0347c03 r5:e82ca280
>  r4:e82ca280
> [<c01902c8>] (SyS_ioctl) from [<c000fd60>] (ret_fast_syscall+0x0/0x1c)
>  r8:c000ff04 r7:00000036 r6:000261d0 r5:00000001 r4:009162e8 r3:00000001
> ---[ end trace 4fdd40e5adfc4485 ]---
> ------------[ cut here ]------------
> WARNING: CPU: 1 PID: 1889 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0x9c/0xa8 [imx_media_csi]
> Modules linked in: caam_jr uvcvideo snd_soc_imx_sgtl5000 snd_soc_fsl_asoc_card snd_soc_imx_spdif imx_media_csi(C) imx6_mipi_csi2(C) snd_soc_imx_audmux snd_soc_sgtl5000 imx219 imx_media_ic(C) imx_media_capture(C) imx_media_vdic(C) caam video_multiplexer imx_sdma coda v4l2_mem2mem videobuf2_v4l2 imx2_wdt imx_vdoa videobuf2_dma_contig videobuf2_core videobuf2_vmalloc videobuf2_memops snd_soc_fsl_ssi
> imx_thermal snd_soc_fsl_spdif imx_pcm_dma imx_media(C) imx_media_common(C) nfsd
> rc_pinnacle_pctv_hd dw_hdmi_ahb_audio dw_hdmi_cec etnaviv
> CPU: 1 PID: 1889 Comm: media-ctl Tainted: G        WC      4.11.0-rc1+ #2125
> Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
> Backtrace:
> [<c0013ba4>] (dump_backtrace) from [<c0013de4>] (show_stack+0x18/0x1c)
>  r6:600e0013 r5:ffffffff r4:00000000 r3:00000000
> [<c0013dcc>] (show_stack) from [<c033f728>] (dump_stack+0xa4/0xdc)
> [<c033f684>] (dump_stack) from [<c00326cc>] (__warn+0xdc/0x108)
>  r6:bf124014 r5:00000000 r4:00000000 r3:c09ea4a8
> [<c00325f0>] (__warn) from [<c0032720>] (warn_slowpath_null+0x28/0x30)
>  r10:ede00010 r8:ede4a348 r7:ee000800 r6:d0395140 r5:00000000 r4:d0395010
> [<c00326f8>] (warn_slowpath_null) from [<bf1229e0>] (csi_s_power+0x9c/0xa8 [imx_media_csi])
> [<bf122944>] (csi_s_power [imx_media_csi]) from [<bf04a930>] (imx_media_set_power+0x3c/0x108 [imx_media_common])
>  r7:ee000800 r6:00000000 r5:00000000 r4:0000000c
> [<bf04a8f4>] (imx_media_set_power [imx_media_common]) from [<bf04aa34>] (imx_media_pipeline_set_power+0x38/0x40 [imx_media_common])
>  r10:00000001 r9:00000001 r8:ede4a348 r7:ede00010 r6:ede4a348 r5:ee000800
>  r4:00000001
> [<bf04a9fc>] (imx_media_pipeline_set_power [imx_media_common]) from [<bf052148>] (imx_media_link_notify+0xf0/0x144 [imx_media])
>  r7:ede00010 r6:d0320480 r5:ee000800 r4:ee000800
> [<bf052058>] (imx_media_link_notify [imx_media]) from [<c04fa858>] (__media_entity_setup_link+0x110/0x1d8)
>  r10:c0347c03 r9:d7eb3dc8 r8:befe92b0 r7:ede00010 r6:00000000 r5:00000001
>  r4:d0320480 r3:bf052058
> [<c04fa748>] (__media_entity_setup_link) from [<c04f9bb0>] (media_device_setup_link+0x84/0x90)
>  r7:ede00010 r6:ede00010 r5:d039501c r4:d7eb3dc8
> [<c04f9b2c>] (media_device_setup_link) from [<c04f9e94>] (media_device_ioctl+0xa4/0x148)
>  r6:00000000 r5:d7eb3dc8 r4:c077b014 r3:c04f9b2c
> [<c04f9df0>] (media_device_ioctl) from [<c04fa3a0>] (media_ioctl+0x38/0x4c)
>  r10:ed5eca68 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:00000003 r5:e82ca500
>  r4:c0190304
> [<c04fa368>] (media_ioctl) from [<c018f9c0>] (do_vfs_ioctl+0x98/0x9a0)
> [<c018f928>] (do_vfs_ioctl) from [<c0190304>] (SyS_ioctl+0x3c/0x60)
>  r10:00000000 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:c0347c03 r5:e82ca500
>  r4:e82ca500
> [<c01902c8>] (SyS_ioctl) from [<c000fd60>] (ret_fast_syscall+0x0/0x1c)
>  r8:c000ff04 r7:00000036 r6:000261d0 r5:00000001 r4:0091737c r3:00000001
> ---[ end trace 4fdd40e5adfc4486 ]---
>

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 10:51 AM, Russell King - ARM Linux wrote:
> I've just looked at my test system's dmesg, and spotted this in the log.
> It's been a while since these popped out of the kernel, so I don't know
> what caused them (other than the obvious, a media-ctl command.)
>
> My script which sets this up only enables links, and then configures the
> formats etc, and doesn't disable them, so I don't see why the power
> count should be going negative.

There's actually nothing preventing userland from disabling a link
multiple times, and imx_media_link_notify() complies, and so
csi_s_power(OFF) gets called multiple times, and so that WARN_ON()
in there is silly, I borrowed this from other MC driver examples,
but it makes no sense to me, I'll remove it and prevent the power
count from going negative.

Steve



>
> ------------[ cut here ]------------
> WARNING: CPU: 1 PID: 1889 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0x9c/0xa8 [imx_media_csi]
> Modules linked in: caam_jr uvcvideo snd_soc_imx_sgtl5000 snd_soc_fsl_asoc_card snd_soc_imx_spdif imx_media_csi(C) imx6_mipi_csi2(C) snd_soc_imx_audmux snd_soc_sgtl5000 imx219 imx_media_ic(C) imx_media_capture(C) imx_media_vdic(C) caam video_multiplexer imx_sdma coda v4l2_mem2mem videobuf2_v4l2 imx2_wdt imx_vdoa videobuf2_dma_contig videobuf2_core videobuf2_vmalloc videobuf2_memops snd_soc_fsl_ssi
> imx_thermal snd_soc_fsl_spdif imx_pcm_dma imx_media(C) imx_media_common(C) nfsd
> rc_pinnacle_pctv_hd dw_hdmi_ahb_audio dw_hdmi_cec etnaviv
> CPU: 1 PID: 1889 Comm: media-ctl Tainted: G         C      4.11.0-rc1+ #2125
> Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
> Backtrace:
> [<c0013ba4>] (dump_backtrace) from [<c0013de4>] (show_stack+0x18/0x1c)
>  r6:600e0013 r5:ffffffff r4:00000000 r3:00000000
> [<c0013dcc>] (show_stack) from [<c033f728>] (dump_stack+0xa4/0xdc)
> [<c033f684>] (dump_stack) from [<c00326cc>] (__warn+0xdc/0x108)
>  r6:bf124014 r5:00000000 r4:00000000 r3:c09ea4a8
> [<c00325f0>] (__warn) from [<c0032720>] (warn_slowpath_null+0x28/0x30)
>  r10:ede00010 r8:ede4a348 r7:d039501c r6:d0395140 r5:00000000 r4:d0395010
> [<c00326f8>] (warn_slowpath_null) from [<bf1229e0>] (csi_s_power+0x9c/0xa8 [imx_media_csi])
> [<bf122944>] (csi_s_power [imx_media_csi]) from [<bf04a930>] (imx_media_set_power+0x3c/0x108 [imx_media_common])
>  r7:d039501c r6:00000000 r5:00000000 r4:0000000c
> [<bf04a8f4>] (imx_media_set_power [imx_media_common]) from [<bf04aa34>] (imx_media_pipeline_set_power+0x38/0x40 [imx_media_common])
>  r10:00000001 r9:00000001 r8:ede4a348 r7:ede00010 r6:ede4a348 r5:d039501c
>  r4:00000001
> [<bf04a9fc>] (imx_media_pipeline_set_power [imx_media_common]) from [<bf052148>] (imx_media_link_notify+0xf0/0x144 [imx_media])
>  r7:ede00010 r6:ed59f900 r5:00000000 r4:d039501c
> [<bf052058>] (imx_media_link_notify [imx_media]) from [<c04fa858>] (__media_entity_setup_link+0x110/0x1d8)
>  r10:c0347c03 r9:d7eb3dc8 r8:befe92b0 r7:ede00010 r6:00000000 r5:00000001
>  r4:ed59f900 r3:bf052058
> [<c04fa748>] (__media_entity_setup_link) from [<c04f9bb0>] (media_device_setup_link+0x84/0x90)
>  r7:ede00010 r6:ede00010 r5:ef3fd810 r4:d7eb3dc8
> [<c04f9b2c>] (media_device_setup_link) from [<c04f9e94>] (media_device_ioctl+0xa4/0x148)
>  r6:00000000 r5:d7eb3dc8 r4:c077b014 r3:c04f9b2c
> [<c04f9df0>] (media_device_ioctl) from [<c04fa3a0>] (media_ioctl+0x38/0x4c)
>  r10:ed5eca68 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:00000003 r5:e82ca280
>  r4:c0190304
> [<c04fa368>] (media_ioctl) from [<c018f9c0>] (do_vfs_ioctl+0x98/0x9a0)
> [<c018f928>] (do_vfs_ioctl) from [<c0190304>] (SyS_ioctl+0x3c/0x60)
>  r10:00000000 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:c0347c03 r5:e82ca280
>  r4:e82ca280
> [<c01902c8>] (SyS_ioctl) from [<c000fd60>] (ret_fast_syscall+0x0/0x1c)
>  r8:c000ff04 r7:00000036 r6:000261d0 r5:00000001 r4:009162e8 r3:00000001
> ---[ end trace 4fdd40e5adfc4485 ]---
> ------------[ cut here ]------------
> WARNING: CPU: 1 PID: 1889 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0x9c/0xa8 [imx_media_csi]
> Modules linked in: caam_jr uvcvideo snd_soc_imx_sgtl5000 snd_soc_fsl_asoc_card snd_soc_imx_spdif imx_media_csi(C) imx6_mipi_csi2(C) snd_soc_imx_audmux snd_soc_sgtl5000 imx219 imx_media_ic(C) imx_media_capture(C) imx_media_vdic(C) caam video_multiplexer imx_sdma coda v4l2_mem2mem videobuf2_v4l2 imx2_wdt imx_vdoa videobuf2_dma_contig videobuf2_core videobuf2_vmalloc videobuf2_memops snd_soc_fsl_ssi
> imx_thermal snd_soc_fsl_spdif imx_pcm_dma imx_media(C) imx_media_common(C) nfsd
> rc_pinnacle_pctv_hd dw_hdmi_ahb_audio dw_hdmi_cec etnaviv
> CPU: 1 PID: 1889 Comm: media-ctl Tainted: G        WC      4.11.0-rc1+ #2125
> Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
> Backtrace:
> [<c0013ba4>] (dump_backtrace) from [<c0013de4>] (show_stack+0x18/0x1c)
>  r6:600e0013 r5:ffffffff r4:00000000 r3:00000000
> [<c0013dcc>] (show_stack) from [<c033f728>] (dump_stack+0xa4/0xdc)
> [<c033f684>] (dump_stack) from [<c00326cc>] (__warn+0xdc/0x108)
>  r6:bf124014 r5:00000000 r4:00000000 r3:c09ea4a8
> [<c00325f0>] (__warn) from [<c0032720>] (warn_slowpath_null+0x28/0x30)
>  r10:ede00010 r8:ede4a348 r7:ee000800 r6:d0395140 r5:00000000 r4:d0395010
> [<c00326f8>] (warn_slowpath_null) from [<bf1229e0>] (csi_s_power+0x9c/0xa8 [imx_media_csi])
> [<bf122944>] (csi_s_power [imx_media_csi]) from [<bf04a930>] (imx_media_set_power+0x3c/0x108 [imx_media_common])
>  r7:ee000800 r6:00000000 r5:00000000 r4:0000000c
> [<bf04a8f4>] (imx_media_set_power [imx_media_common]) from [<bf04aa34>] (imx_media_pipeline_set_power+0x38/0x40 [imx_media_common])
>  r10:00000001 r9:00000001 r8:ede4a348 r7:ede00010 r6:ede4a348 r5:ee000800
>  r4:00000001
> [<bf04a9fc>] (imx_media_pipeline_set_power [imx_media_common]) from [<bf052148>] (imx_media_link_notify+0xf0/0x144 [imx_media])
>  r7:ede00010 r6:d0320480 r5:ee000800 r4:ee000800
> [<bf052058>] (imx_media_link_notify [imx_media]) from [<c04fa858>] (__media_entity_setup_link+0x110/0x1d8)
>  r10:c0347c03 r9:d7eb3dc8 r8:befe92b0 r7:ede00010 r6:00000000 r5:00000001
>  r4:d0320480 r3:bf052058
> [<c04fa748>] (__media_entity_setup_link) from [<c04f9bb0>] (media_device_setup_link+0x84/0x90)
>  r7:ede00010 r6:ede00010 r5:d039501c r4:d7eb3dc8
> [<c04f9b2c>] (media_device_setup_link) from [<c04f9e94>] (media_device_ioctl+0xa4/0x148)
>  r6:00000000 r5:d7eb3dc8 r4:c077b014 r3:c04f9b2c
> [<c04f9df0>] (media_device_ioctl) from [<c04fa3a0>] (media_ioctl+0x38/0x4c)
>  r10:ed5eca68 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:00000003 r5:e82ca500
>  r4:c0190304
> [<c04fa368>] (media_ioctl) from [<c018f9c0>] (do_vfs_ioctl+0x98/0x9a0)
> [<c018f928>] (do_vfs_ioctl) from [<c0190304>] (SyS_ioctl+0x3c/0x60)
>  r10:00000000 r9:d7eb2000 r8:befe92b0 r7:00000003 r6:c0347c03 r5:e82ca500
>  r4:e82ca500
> [<c01902c8>] (SyS_ioctl) from [<c000fd60>] (ret_fast_syscall+0x0/0x1c)
>  r8:c000ff04 r7:00000036 r6:000261d0 r5:00000001 r4:0091737c r3:00000001
> ---[ end trace 4fdd40e5adfc4486 ]---
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 12, 2017 at 12:21:45PM -0700, Steve Longerbeam wrote:
> There's actually nothing preventing userland from disabling a link
> multiple times, and imx_media_link_notify() complies, and so
> csi_s_power(OFF) gets called multiple times, and so that WARN_ON()
> in there is silly, I borrowed this from other MC driver examples,
> but it makes no sense to me, I'll remove it and prevent the power
> count from going negative.

Hmm.  So what happens if one of the CSI's links is enabled, and we
disable a different link from the CSI several times?  Doesn't that
mean the power count will go to zero despite there being an enabled
link?

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 12, 2017 at 12:21:45PM -0700, Steve Longerbeam wrote:
> There's actually nothing preventing userland from disabling a link
> multiple times, and imx_media_link_notify() complies, and so
> csi_s_power(OFF) gets called multiple times, and so that WARN_ON()
> in there is silly, I borrowed this from other MC driver examples,
> but it makes no sense to me, I'll remove it and prevent the power
> count from going negative.

Hmm.  So what happens if one of the CSI's links is enabled, and we
disable a different link from the CSI several times?  Doesn't that
mean the power count will go to zero despite there being an enabled
link?

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 12, 2017 at 12:21:45PM -0700, Steve Longerbeam wrote:
> There's actually nothing preventing userland from disabling a link
> multiple times, and imx_media_link_notify() complies, and so
> csi_s_power(OFF) gets called multiple times, and so that WARN_ON()
> in there is silly, I borrowed this from other MC driver examples,
> but it makes no sense to me, I'll remove it and prevent the power
> count from going negative.

Hmm.  So what happens if one of the CSI's links is enabled, and we
disable a different link from the CSI several times?  Doesn't that
mean the power count will go to zero despite there being an enabled
link?

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 12:29 PM, Russell King - ARM Linux wrote:
> On Sun, Mar 12, 2017 at 12:21:45PM -0700, Steve Longerbeam wrote:
>> There's actually nothing preventing userland from disabling a link
>> multiple times, and imx_media_link_notify() complies, and so
>> csi_s_power(OFF) gets called multiple times, and so that WARN_ON()
>> in there is silly, I borrowed this from other MC driver examples,
>> but it makes no sense to me, I'll remove it and prevent the power
>> count from going negative.
>
> Hmm.  So what happens if one of the CSI's links is enabled, and we
> disable a different link from the CSI several times?  Doesn't that
> mean the power count will go to zero despite there being an enabled
> link?

Yes, the CSI will be powered off even if it still has an enabled link.
But one of its other links has been disabled, meaning the pipeline as
a whole is disabled. So I think it makes sense to power down the CSI,
the pipeline isn't usable at that point.

And remember that the CSI does not allow both output pads to be enabled
at the same time. If that were so then indeed there would be a problem,
because it would mean there is another active pipeline that requires the
CSI being powered on, but that's not the case.

I think this is consistent with the other entities as well, but I will
double check.

Steve

[PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 12:29 PM, Russell King - ARM Linux wrote:
> On Sun, Mar 12, 2017 at 12:21:45PM -0700, Steve Longerbeam wrote:
>> There's actually nothing preventing userland from disabling a link
>> multiple times, and imx_media_link_notify() complies, and so
>> csi_s_power(OFF) gets called multiple times, and so that WARN_ON()
>> in there is silly, I borrowed this from other MC driver examples,
>> but it makes no sense to me, I'll remove it and prevent the power
>> count from going negative.
>
> Hmm.  So what happens if one of the CSI's links is enabled, and we
> disable a different link from the CSI several times?  Doesn't that
> mean the power count will go to zero despite there being an enabled
> link?

Yes, the CSI will be powered off even if it still has an enabled link.
But one of its other links has been disabled, meaning the pipeline as
a whole is disabled. So I think it makes sense to power down the CSI,
the pipeline isn't usable at that point.

And remember that the CSI does not allow both output pads to be enabled
at the same time. If that were so then indeed there would be a problem,
because it would mean there is another active pipeline that requires the
CSI being powered on, but that's not the case.

I think this is consistent with the other entities as well, but I will
double check.

Steve

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 12:29 PM, Russell King - ARM Linux wrote:
> On Sun, Mar 12, 2017 at 12:21:45PM -0700, Steve Longerbeam wrote:
>> There's actually nothing preventing userland from disabling a link
>> multiple times, and imx_media_link_notify() complies, and so
>> csi_s_power(OFF) gets called multiple times, and so that WARN_ON()
>> in there is silly, I borrowed this from other MC driver examples,
>> but it makes no sense to me, I'll remove it and prevent the power
>> count from going negative.
>
> Hmm.  So what happens if one of the CSI's links is enabled, and we
> disable a different link from the CSI several times?  Doesn't that
> mean the power count will go to zero despite there being an enabled
> link?

Yes, the CSI will be powered off even if it still has an enabled link.
But one of its other links has been disabled, meaning the pipeline as
a whole is disabled. So I think it makes sense to power down the CSI,
the pipeline isn't usable at that point.

And remember that the CSI does not allow both output pads to be enabled
at the same time. If that were so then indeed there would be a problem,
because it would mean there is another active pipeline that requires the
CSI being powered on, but that's not the case.

I think this is consistent with the other entities as well, but I will
double check.

Steve

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 12:44 PM, Steve Longerbeam wrote:
>
>
> On 03/12/2017 12:29 PM, Russell King - ARM Linux wrote:
>> On Sun, Mar 12, 2017 at 12:21:45PM -0700, Steve Longerbeam wrote:
>>> There's actually nothing preventing userland from disabling a link
>>> multiple times, and imx_media_link_notify() complies, and so
>>> csi_s_power(OFF) gets called multiple times, and so that WARN_ON()
>>> in there is silly, I borrowed this from other MC driver examples,
>>> but it makes no sense to me, I'll remove it and prevent the power
>>> count from going negative.
>>
>> Hmm.  So what happens if one of the CSI's links is enabled, and we
>> disable a different link from the CSI several times?  Doesn't that
>> mean the power count will go to zero despite there being an enabled
>> link?
>
> Yes, the CSI will be powered off even if it still has an enabled link.
> But one of its other links has been disabled, meaning the pipeline as
> a whole is disabled. So I think it makes sense to power down the CSI,
> the pipeline isn't usable at that point.
>
> And remember that the CSI does not allow both output pads to be enabled
> at the same time. If that were so then indeed there would be a problem,
> because it would mean there is another active pipeline that requires the
> CSI being powered on, but that's not the case.
>
> I think this is consistent with the other entities as well, but I will
> double check.


At first I thought this could be a problem for one entity, the csi-2
receiver.

It can enable all four of its output pads at once (if the input stream
contains all 4 virtual channels, the csi-2 receiver must support
demuxing all of them onto all 4 of its output pads).

But after more review, this should not be an issue. If a csi-2 sink
(a CSI or a CSI mux) link is disabled, the csi-2 receiver is no longer
reachable from that sink, so attempts to disable the csi-2 via that
path again is not possible. The other potential problem is disabling
from the csi-2's own sink pad, but in that case the csi-2 no longer
has a source, so again it makes sense to power off the csi-2 even
if it has enabled output pads.


Steve

[PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 12:44 PM, Steve Longerbeam wrote:
>
>
> On 03/12/2017 12:29 PM, Russell King - ARM Linux wrote:
>> On Sun, Mar 12, 2017 at 12:21:45PM -0700, Steve Longerbeam wrote:
>>> There's actually nothing preventing userland from disabling a link
>>> multiple times, and imx_media_link_notify() complies, and so
>>> csi_s_power(OFF) gets called multiple times, and so that WARN_ON()
>>> in there is silly, I borrowed this from other MC driver examples,
>>> but it makes no sense to me, I'll remove it and prevent the power
>>> count from going negative.
>>
>> Hmm.  So what happens if one of the CSI's links is enabled, and we
>> disable a different link from the CSI several times?  Doesn't that
>> mean the power count will go to zero despite there being an enabled
>> link?
>
> Yes, the CSI will be powered off even if it still has an enabled link.
> But one of its other links has been disabled, meaning the pipeline as
> a whole is disabled. So I think it makes sense to power down the CSI,
> the pipeline isn't usable at that point.
>
> And remember that the CSI does not allow both output pads to be enabled
> at the same time. If that were so then indeed there would be a problem,
> because it would mean there is another active pipeline that requires the
> CSI being powered on, but that's not the case.
>
> I think this is consistent with the other entities as well, but I will
> double check.


At first I thought this could be a problem for one entity, the csi-2
receiver.

It can enable all four of its output pads at once (if the input stream
contains all 4 virtual channels, the csi-2 receiver must support
demuxing all of them onto all 4 of its output pads).

But after more review, this should not be an issue. If a csi-2 sink
(a CSI or a CSI mux) link is disabled, the csi-2 receiver is no longer
reachable from that sink, so attempts to disable the csi-2 via that
path again is not possible. The other potential problem is disabling
from the csi-2's own sink pad, but in that case the csi-2 no longer
has a source, so again it makes sense to power off the csi-2 even
if it has enabled output pads.


Steve

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 12:44 PM, Steve Longerbeam wrote:
>
>
> On 03/12/2017 12:29 PM, Russell King - ARM Linux wrote:
>> On Sun, Mar 12, 2017 at 12:21:45PM -0700, Steve Longerbeam wrote:
>>> There's actually nothing preventing userland from disabling a link
>>> multiple times, and imx_media_link_notify() complies, and so
>>> csi_s_power(OFF) gets called multiple times, and so that WARN_ON()
>>> in there is silly, I borrowed this from other MC driver examples,
>>> but it makes no sense to me, I'll remove it and prevent the power
>>> count from going negative.
>>
>> Hmm.  So what happens if one of the CSI's links is enabled, and we
>> disable a different link from the CSI several times?  Doesn't that
>> mean the power count will go to zero despite there being an enabled
>> link?
>
> Yes, the CSI will be powered off even if it still has an enabled link.
> But one of its other links has been disabled, meaning the pipeline as
> a whole is disabled. So I think it makes sense to power down the CSI,
> the pipeline isn't usable at that point.
>
> And remember that the CSI does not allow both output pads to be enabled
> at the same time. If that were so then indeed there would be a problem,
> because it would mean there is another active pipeline that requires the
> CSI being powered on, but that's not the case.
>
> I think this is consistent with the other entities as well, but I will
> double check.


At first I thought this could be a problem for one entity, the csi-2
receiver.

It can enable all four of its output pads at once (if the input stream
contains all 4 virtual channels, the csi-2 receiver must support
demuxing all of them onto all 4 of its output pads).

But after more review, this should not be an issue. If a csi-2 sink
(a CSI or a CSI mux) link is disabled, the csi-2 receiver is no longer
reachable from that sink, so attempts to disable the csi-2 via that
path again is not possible. The other potential problem is disabling
from the csi-2's own sink pad, but in that case the csi-2 no longer
has a source, so again it makes sense to power off the csi-2 even
if it has enabled output pads.


Steve
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 01:16 PM, Steve Longerbeam wrote:
>
>
> On 03/12/2017 12:44 PM, Steve Longerbeam wrote:
>>
>>
>> On 03/12/2017 12:29 PM, Russell King - ARM Linux wrote:
>>> On Sun, Mar 12, 2017 at 12:21:45PM -0700, Steve Longerbeam wrote:
>>>> There's actually nothing preventing userland from disabling a link
>>>> multiple times, and imx_media_link_notify() complies, and so
>>>> csi_s_power(OFF) gets called multiple times, and so that WARN_ON()
>>>> in there is silly, I borrowed this from other MC driver examples,
>>>> but it makes no sense to me, I'll remove it and prevent the power
>>>> count from going negative.
>>>
>>> Hmm.  So what happens if one of the CSI's links is enabled, and we
>>> disable a different link from the CSI several times?  Doesn't that
>>> mean the power count will go to zero despite there being an enabled
>>> link?
>>
>> Yes, the CSI will be powered off even if it still has an enabled link.
>> But one of its other links has been disabled, meaning the pipeline as
>> a whole is disabled. So I think it makes sense to power down the CSI,
>> the pipeline isn't usable at that point.
>>
>> And remember that the CSI does not allow both output pads to be enabled
>> at the same time. If that were so then indeed there would be a problem,
>> because it would mean there is another active pipeline that requires the
>> CSI being powered on, but that's not the case.
>>
>> I think this is consistent with the other entities as well, but I will
>> double check.
>
>
> At first I thought this could be a problem for one entity, the csi-2
> receiver.
>
> It can enable all four of its output pads at once (if the input stream
> contains all 4 virtual channels, the csi-2 receiver must support
> demuxing all of them onto all 4 of its output pads).
>
> But after more review, this should not be an issue. If a csi-2 sink
> (a CSI or a CSI mux) link is disabled, the csi-2 receiver is no longer
> reachable from that sink, so attempts to disable the csi-2 via that
> path again is not possible. The other potential problem is disabling
> from the csi-2's own sink pad, but in that case the csi-2 no longer
> has a source, so again it makes sense to power off the csi-2 even
> if it has enabled output pads.
>

But hold on, if my logic is correct, then why did the CSI power-off
get reached in your case, multiple times? Yes I think there is a bug,
link_notify() is not checking if the link has already been disabled.
I will fix this. But I'm surprised media core's link_notify handling
doesn't do this.

Steve

[PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 01:16 PM, Steve Longerbeam wrote:
>
>
> On 03/12/2017 12:44 PM, Steve Longerbeam wrote:
>>
>>
>> On 03/12/2017 12:29 PM, Russell King - ARM Linux wrote:
>>> On Sun, Mar 12, 2017 at 12:21:45PM -0700, Steve Longerbeam wrote:
>>>> There's actually nothing preventing userland from disabling a link
>>>> multiple times, and imx_media_link_notify() complies, and so
>>>> csi_s_power(OFF) gets called multiple times, and so that WARN_ON()
>>>> in there is silly, I borrowed this from other MC driver examples,
>>>> but it makes no sense to me, I'll remove it and prevent the power
>>>> count from going negative.
>>>
>>> Hmm.  So what happens if one of the CSI's links is enabled, and we
>>> disable a different link from the CSI several times?  Doesn't that
>>> mean the power count will go to zero despite there being an enabled
>>> link?
>>
>> Yes, the CSI will be powered off even if it still has an enabled link.
>> But one of its other links has been disabled, meaning the pipeline as
>> a whole is disabled. So I think it makes sense to power down the CSI,
>> the pipeline isn't usable at that point.
>>
>> And remember that the CSI does not allow both output pads to be enabled
>> at the same time. If that were so then indeed there would be a problem,
>> because it would mean there is another active pipeline that requires the
>> CSI being powered on, but that's not the case.
>>
>> I think this is consistent with the other entities as well, but I will
>> double check.
>
>
> At first I thought this could be a problem for one entity, the csi-2
> receiver.
>
> It can enable all four of its output pads at once (if the input stream
> contains all 4 virtual channels, the csi-2 receiver must support
> demuxing all of them onto all 4 of its output pads).
>
> But after more review, this should not be an issue. If a csi-2 sink
> (a CSI or a CSI mux) link is disabled, the csi-2 receiver is no longer
> reachable from that sink, so attempts to disable the csi-2 via that
> path again is not possible. The other potential problem is disabling
> from the csi-2's own sink pad, but in that case the csi-2 no longer
> has a source, so again it makes sense to power off the csi-2 even
> if it has enabled output pads.
>

But hold on, if my logic is correct, then why did the CSI power-off
get reached in your case, multiple times? Yes I think there is a bug,
link_notify() is not checking if the link has already been disabled.
I will fix this. But I'm surprised media core's link_notify handling
doesn't do this.

Steve

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 01:16 PM, Steve Longerbeam wrote:
>
>
> On 03/12/2017 12:44 PM, Steve Longerbeam wrote:
>>
>>
>> On 03/12/2017 12:29 PM, Russell King - ARM Linux wrote:
>>> On Sun, Mar 12, 2017 at 12:21:45PM -0700, Steve Longerbeam wrote:
>>>> There's actually nothing preventing userland from disabling a link
>>>> multiple times, and imx_media_link_notify() complies, and so
>>>> csi_s_power(OFF) gets called multiple times, and so that WARN_ON()
>>>> in there is silly, I borrowed this from other MC driver examples,
>>>> but it makes no sense to me, I'll remove it and prevent the power
>>>> count from going negative.
>>>
>>> Hmm.  So what happens if one of the CSI's links is enabled, and we
>>> disable a different link from the CSI several times?  Doesn't that
>>> mean the power count will go to zero despite there being an enabled
>>> link?
>>
>> Yes, the CSI will be powered off even if it still has an enabled link.
>> But one of its other links has been disabled, meaning the pipeline as
>> a whole is disabled. So I think it makes sense to power down the CSI,
>> the pipeline isn't usable at that point.
>>
>> And remember that the CSI does not allow both output pads to be enabled
>> at the same time. If that were so then indeed there would be a problem,
>> because it would mean there is another active pipeline that requires the
>> CSI being powered on, but that's not the case.
>>
>> I think this is consistent with the other entities as well, but I will
>> double check.
>
>
> At first I thought this could be a problem for one entity, the csi-2
> receiver.
>
> It can enable all four of its output pads at once (if the input stream
> contains all 4 virtual channels, the csi-2 receiver must support
> demuxing all of them onto all 4 of its output pads).
>
> But after more review, this should not be an issue. If a csi-2 sink
> (a CSI or a CSI mux) link is disabled, the csi-2 receiver is no longer
> reachable from that sink, so attempts to disable the csi-2 via that
> path again is not possible. The other potential problem is disabling
> from the csi-2's own sink pad, but in that case the csi-2 no longer
> has a source, so again it makes sense to power off the csi-2 even
> if it has enabled output pads.
>

But hold on, if my logic is correct, then why did the CSI power-off
get reached in your case, multiple times? Yes I think there is a bug,
link_notify() is not checking if the link has already been disabled.
I will fix this. But I'm surprised media core's link_notify handling
doesn't do this.

Steve

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 01:36 PM, Steve Longerbeam wrote:
>
>
> On 03/12/2017 01:16 PM, Steve Longerbeam wrote:
>>
>>
>> On 03/12/2017 12:44 PM, Steve Longerbeam wrote:
>>>
>>>
>>> On 03/12/2017 12:29 PM, Russell King - ARM Linux wrote:
>>>> On Sun, Mar 12, 2017 at 12:21:45PM -0700, Steve Longerbeam wrote:
>>>>> There's actually nothing preventing userland from disabling a link
>>>>> multiple times, and imx_media_link_notify() complies, and so
>>>>> csi_s_power(OFF) gets called multiple times, and so that WARN_ON()
>>>>> in there is silly, I borrowed this from other MC driver examples,
>>>>> but it makes no sense to me, I'll remove it and prevent the power
>>>>> count from going negative.
>>>>
>>>> Hmm.  So what happens if one of the CSI's links is enabled, and we
>>>> disable a different link from the CSI several times?  Doesn't that
>>>> mean the power count will go to zero despite there being an enabled
>>>> link?
>>>
>>> Yes, the CSI will be powered off even if it still has an enabled link.
>>> But one of its other links has been disabled, meaning the pipeline as
>>> a whole is disabled. So I think it makes sense to power down the CSI,
>>> the pipeline isn't usable at that point.
>>>
>>> And remember that the CSI does not allow both output pads to be enabled
>>> at the same time. If that were so then indeed there would be a problem,
>>> because it would mean there is another active pipeline that requires the
>>> CSI being powered on, but that's not the case.
>>>
>>> I think this is consistent with the other entities as well, but I will
>>> double check.
>>
>>
>> At first I thought this could be a problem for one entity, the csi-2
>> receiver.
>>
>> It can enable all four of its output pads at once (if the input stream
>> contains all 4 virtual channels, the csi-2 receiver must support
>> demuxing all of them onto all 4 of its output pads).
>>
>> But after more review, this should not be an issue. If a csi-2 sink
>> (a CSI or a CSI mux) link is disabled, the csi-2 receiver is no longer
>> reachable from that sink, so attempts to disable the csi-2 via that
>> path again is not possible. The other potential problem is disabling
>> from the csi-2's own sink pad, but in that case the csi-2 no longer
>> has a source, so again it makes sense to power off the csi-2 even
>> if it has enabled output pads.
>>
>
> But hold on, if my logic is correct, then why did the CSI power-off
> get reached in your case, multiple times? Yes I think there is a bug,
> link_notify() is not checking if the link has already been disabled.
> I will fix this. But I'm surprised media core's link_notify handling
> doesn't do this.

but it does:

int __media_entity_setup_link(struct media_link *link, u32 flags)
{
...
     if (link->flags == flags)
         return 0;
...
}

What the heck. Anyway, I'll track this down.

Steve

>
> Steve
>

[PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 01:36 PM, Steve Longerbeam wrote:
>
>
> On 03/12/2017 01:16 PM, Steve Longerbeam wrote:
>>
>>
>> On 03/12/2017 12:44 PM, Steve Longerbeam wrote:
>>>
>>>
>>> On 03/12/2017 12:29 PM, Russell King - ARM Linux wrote:
>>>> On Sun, Mar 12, 2017 at 12:21:45PM -0700, Steve Longerbeam wrote:
>>>>> There's actually nothing preventing userland from disabling a link
>>>>> multiple times, and imx_media_link_notify() complies, and so
>>>>> csi_s_power(OFF) gets called multiple times, and so that WARN_ON()
>>>>> in there is silly, I borrowed this from other MC driver examples,
>>>>> but it makes no sense to me, I'll remove it and prevent the power
>>>>> count from going negative.
>>>>
>>>> Hmm.  So what happens if one of the CSI's links is enabled, and we
>>>> disable a different link from the CSI several times?  Doesn't that
>>>> mean the power count will go to zero despite there being an enabled
>>>> link?
>>>
>>> Yes, the CSI will be powered off even if it still has an enabled link.
>>> But one of its other links has been disabled, meaning the pipeline as
>>> a whole is disabled. So I think it makes sense to power down the CSI,
>>> the pipeline isn't usable at that point.
>>>
>>> And remember that the CSI does not allow both output pads to be enabled
>>> at the same time. If that were so then indeed there would be a problem,
>>> because it would mean there is another active pipeline that requires the
>>> CSI being powered on, but that's not the case.
>>>
>>> I think this is consistent with the other entities as well, but I will
>>> double check.
>>
>>
>> At first I thought this could be a problem for one entity, the csi-2
>> receiver.
>>
>> It can enable all four of its output pads at once (if the input stream
>> contains all 4 virtual channels, the csi-2 receiver must support
>> demuxing all of them onto all 4 of its output pads).
>>
>> But after more review, this should not be an issue. If a csi-2 sink
>> (a CSI or a CSI mux) link is disabled, the csi-2 receiver is no longer
>> reachable from that sink, so attempts to disable the csi-2 via that
>> path again is not possible. The other potential problem is disabling
>> from the csi-2's own sink pad, but in that case the csi-2 no longer
>> has a source, so again it makes sense to power off the csi-2 even
>> if it has enabled output pads.
>>
>
> But hold on, if my logic is correct, then why did the CSI power-off
> get reached in your case, multiple times? Yes I think there is a bug,
> link_notify() is not checking if the link has already been disabled.
> I will fix this. But I'm surprised media core's link_notify handling
> doesn't do this.

but it does:

int __media_entity_setup_link(struct media_link *link, u32 flags)
{
...
     if (link->flags == flags)
         return 0;
...
}

What the heck. Anyway, I'll track this down.

Steve

>
> Steve
>

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 01:36 PM, Steve Longerbeam wrote:
>
>
> On 03/12/2017 01:16 PM, Steve Longerbeam wrote:
>>
>>
>> On 03/12/2017 12:44 PM, Steve Longerbeam wrote:
>>>
>>>
>>> On 03/12/2017 12:29 PM, Russell King - ARM Linux wrote:
>>>> On Sun, Mar 12, 2017 at 12:21:45PM -0700, Steve Longerbeam wrote:
>>>>> There's actually nothing preventing userland from disabling a link
>>>>> multiple times, and imx_media_link_notify() complies, and so
>>>>> csi_s_power(OFF) gets called multiple times, and so that WARN_ON()
>>>>> in there is silly, I borrowed this from other MC driver examples,
>>>>> but it makes no sense to me, I'll remove it and prevent the power
>>>>> count from going negative.
>>>>
>>>> Hmm.  So what happens if one of the CSI's links is enabled, and we
>>>> disable a different link from the CSI several times?  Doesn't that
>>>> mean the power count will go to zero despite there being an enabled
>>>> link?
>>>
>>> Yes, the CSI will be powered off even if it still has an enabled link.
>>> But one of its other links has been disabled, meaning the pipeline as
>>> a whole is disabled. So I think it makes sense to power down the CSI,
>>> the pipeline isn't usable at that point.
>>>
>>> And remember that the CSI does not allow both output pads to be enabled
>>> at the same time. If that were so then indeed there would be a problem,
>>> because it would mean there is another active pipeline that requires the
>>> CSI being powered on, but that's not the case.
>>>
>>> I think this is consistent with the other entities as well, but I will
>>> double check.
>>
>>
>> At first I thought this could be a problem for one entity, the csi-2
>> receiver.
>>
>> It can enable all four of its output pads at once (if the input stream
>> contains all 4 virtual channels, the csi-2 receiver must support
>> demuxing all of them onto all 4 of its output pads).
>>
>> But after more review, this should not be an issue. If a csi-2 sink
>> (a CSI or a CSI mux) link is disabled, the csi-2 receiver is no longer
>> reachable from that sink, so attempts to disable the csi-2 via that
>> path again is not possible. The other potential problem is disabling
>> from the csi-2's own sink pad, but in that case the csi-2 no longer
>> has a source, so again it makes sense to power off the csi-2 even
>> if it has enabled output pads.
>>
>
> But hold on, if my logic is correct, then why did the CSI power-off
> get reached in your case, multiple times? Yes I think there is a bug,
> link_notify() is not checking if the link has already been disabled.
> I will fix this. But I'm surprised media core's link_notify handling
> doesn't do this.

but it does:

int __media_entity_setup_link(struct media_link *link, u32 flags)
{
...
     if (link->flags == flags)
         return 0;
...
}

What the heck. Anyway, I'll track this down.

Steve

>
> Steve
>

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 12, 2017 at 01:36:32PM -0700, Steve Longerbeam wrote:
> But hold on, if my logic is correct, then why did the CSI power-off
> get reached in your case, multiple times? Yes I think there is a bug,
> link_notify() is not checking if the link has already been disabled.
> I will fix this. But I'm surprised media core's link_notify handling
> doesn't do this.

Well, I think there's something incredibly fishy going on here.  I
turned that dev_dbg() at the top of the function into a dev_info(),
and I get:

root@hbi2ex:~# dmesg |grep -A2 imx-ipuv3-csi
[   53.370949] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
[   53.371015] ------------[ cut here ]------------
[   53.371075] WARNING: CPU: 0 PID: 1515 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 [imx_media_csi]
--
[   53.372624] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
[   53.372637] ------------[ cut here ]------------
[   53.372663] WARNING: CPU: 0 PID: 1515 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 [imx_media_csi]

There isn't a power on event being generated before these two power
off events.  I don't see a power on event even when I attempt to
start streaming either (which fails due to the lack of bayer
support.)

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 12, 2017 at 01:36:32PM -0700, Steve Longerbeam wrote:
> But hold on, if my logic is correct, then why did the CSI power-off
> get reached in your case, multiple times? Yes I think there is a bug,
> link_notify() is not checking if the link has already been disabled.
> I will fix this. But I'm surprised media core's link_notify handling
> doesn't do this.

Well, I think there's something incredibly fishy going on here.  I
turned that dev_dbg() at the top of the function into a dev_info(),
and I get:

root at hbi2ex:~# dmesg |grep -A2 imx-ipuv3-csi
[   53.370949] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
[   53.371015] ------------[ cut here ]------------
[   53.371075] WARNING: CPU: 0 PID: 1515 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 [imx_media_csi]
--
[   53.372624] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
[   53.372637] ------------[ cut here ]------------
[   53.372663] WARNING: CPU: 0 PID: 1515 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 [imx_media_csi]

There isn't a power on event being generated before these two power
off events.  I don't see a power on event even when I attempt to
start streaming either (which fails due to the lack of bayer
support.)

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 12, 2017 at 01:36:32PM -0700, Steve Longerbeam wrote:
> But hold on, if my logic is correct, then why did the CSI power-off
> get reached in your case, multiple times? Yes I think there is a bug,
> link_notify() is not checking if the link has already been disabled.
> I will fix this. But I'm surprised media core's link_notify handling
> doesn't do this.

Well, I think there's something incredibly fishy going on here.  I
turned that dev_dbg() at the top of the function into a dev_info(),
and I get:

root@hbi2ex:~# dmesg |grep -A2 imx-ipuv3-csi
[   53.370949] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
[   53.371015] ------------[ cut here ]------------
[   53.371075] WARNING: CPU: 0 PID: 1515 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 [imx_media_csi]
--
[   53.372624] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
[   53.372637] ------------[ cut here ]------------
[   53.372663] WARNING: CPU: 0 PID: 1515 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 [imx_media_csi]

There isn't a power on event being generated before these two power
off events.  I don't see a power on event even when I attempt to
start streaming either (which fails due to the lack of bayer
support.)

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 12, 2017 at 08:40:37PM +0000, Russell King - ARM Linux wrote:
> On Sun, Mar 12, 2017 at 01:36:32PM -0700, Steve Longerbeam wrote:
> > But hold on, if my logic is correct, then why did the CSI power-off
> > get reached in your case, multiple times? Yes I think there is a bug,
> > link_notify() is not checking if the link has already been disabled.
> > I will fix this. But I'm surprised media core's link_notify handling
> > doesn't do this.
> 
> Well, I think there's something incredibly fishy going on here.  I
> turned that dev_dbg() at the top of the function into a dev_info(),
> and I get:
> 
> root@hbi2ex:~# dmesg |grep -A2 imx-ipuv3-csi
> [   53.370949] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
> [   53.371015] ------------[ cut here ]------------
> [   53.371075] WARNING: CPU: 0 PID: 1515 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 [imx_media_csi]
> --
> [   53.372624] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
> [   53.372637] ------------[ cut here ]------------
> [   53.372663] WARNING: CPU: 0 PID: 1515 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 [imx_media_csi]
> 
> There isn't a power on event being generated before these two power
> off events.  I don't see a power on event even when I attempt to
> start streaming either (which fails due to the lack of bayer
> support.)

Found it - my imx219 driver returns '1' from its s_power function when
powering up, which triggers a bug in your code - when imx_media_set_power()
fails to power up, you call imx_media_set_power() telling it to power
everything off - including devices that are already powered off.

This is really bad news - s_power() may be called via other paths,
such as when the subdev is opened.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 12, 2017 at 08:40:37PM +0000, Russell King - ARM Linux wrote:
> On Sun, Mar 12, 2017 at 01:36:32PM -0700, Steve Longerbeam wrote:
> > But hold on, if my logic is correct, then why did the CSI power-off
> > get reached in your case, multiple times? Yes I think there is a bug,
> > link_notify() is not checking if the link has already been disabled.
> > I will fix this. But I'm surprised media core's link_notify handling
> > doesn't do this.
> 
> Well, I think there's something incredibly fishy going on here.  I
> turned that dev_dbg() at the top of the function into a dev_info(),
> and I get:
> 
> root at hbi2ex:~# dmesg |grep -A2 imx-ipuv3-csi
> [   53.370949] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
> [   53.371015] ------------[ cut here ]------------
> [   53.371075] WARNING: CPU: 0 PID: 1515 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 [imx_media_csi]
> --
> [   53.372624] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
> [   53.372637] ------------[ cut here ]------------
> [   53.372663] WARNING: CPU: 0 PID: 1515 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 [imx_media_csi]
> 
> There isn't a power on event being generated before these two power
> off events.  I don't see a power on event even when I attempt to
> start streaming either (which fails due to the lack of bayer
> support.)

Found it - my imx219 driver returns '1' from its s_power function when
powering up, which triggers a bug in your code - when imx_media_set_power()
fails to power up, you call imx_media_set_power() telling it to power
everything off - including devices that are already powered off.

This is really bad news - s_power() may be called via other paths,
such as when the subdev is opened.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 12, 2017 at 08:40:37PM +0000, Russell King - ARM Linux wrote:
> On Sun, Mar 12, 2017 at 01:36:32PM -0700, Steve Longerbeam wrote:
> > But hold on, if my logic is correct, then why did the CSI power-off
> > get reached in your case, multiple times? Yes I think there is a bug,
> > link_notify() is not checking if the link has already been disabled.
> > I will fix this. But I'm surprised media core's link_notify handling
> > doesn't do this.
> 
> Well, I think there's something incredibly fishy going on here.  I
> turned that dev_dbg() at the top of the function into a dev_info(),
> and I get:
> 
> root@hbi2ex:~# dmesg |grep -A2 imx-ipuv3-csi
> [   53.370949] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
> [   53.371015] ------------[ cut here ]------------
> [   53.371075] WARNING: CPU: 0 PID: 1515 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 [imx_media_csi]
> --
> [   53.372624] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
> [   53.372637] ------------[ cut here ]------------
> [   53.372663] WARNING: CPU: 0 PID: 1515 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 [imx_media_csi]
> 
> There isn't a power on event being generated before these two power
> off events.  I don't see a power on event even when I attempt to
> start streaming either (which fails due to the lack of bayer
> support.)

Found it - my imx219 driver returns '1' from its s_power function when
powering up, which triggers a bug in your code - when imx_media_set_power()
fails to power up, you call imx_media_set_power() telling it to power
everything off - including devices that are already powered off.

This is really bad news - s_power() may be called via other paths,
such as when the subdev is opened.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 02:09 PM, Russell King - ARM Linux wrote:
> On Sun, Mar 12, 2017 at 08:40:37PM +0000, Russell King - ARM Linux wrote:
>> On Sun, Mar 12, 2017 at 01:36:32PM -0700, Steve Longerbeam wrote:
>>> But hold on, if my logic is correct, then why did the CSI power-off
>>> get reached in your case, multiple times? Yes I think there is a bug,
>>> link_notify() is not checking if the link has already been disabled.
>>> I will fix this. But I'm surprised media core's link_notify handling
>>> doesn't do this.
>> Well, I think there's something incredibly fishy going on here.  I
>> turned that dev_dbg() at the top of the function into a dev_info(),
>> and I get:
>>
>> root@hbi2ex:~# dmesg |grep -A2 imx-ipuv3-csi
>> [   53.370949] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
>> [   53.371015] ------------[ cut here ]------------
>> [   53.371075] WARNING: CPU: 0 PID: 1515 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 [imx_media_csi]
>> --
>> [   53.372624] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
>> [   53.372637] ------------[ cut here ]------------
>> [   53.372663] WARNING: CPU: 0 PID: 1515 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 [imx_media_csi]
>>
>> There isn't a power on event being generated before these two power
>> off events.  I don't see a power on event even when I attempt to
>> start streaming either (which fails due to the lack of bayer
>> support.)
> Found it - my imx219 driver returns '1' from its s_power function when
> powering up, which triggers a bug in your code - when imx_media_set_power()
> fails to power up, you call imx_media_set_power() telling it to power
> everything off - including devices that are already powered off.

Yep, there's a bug in the error cleanup in imx_media_pipeline_set_power().
On error, it needs to backout by calling s_power(off) as it is doing, 
but not
through the whole pipeline, but needs to stop at the subdev encountered
just before the subdev that failed. This was causing the s_power() 
imbalance.
I will fix.


>
> This is really bad news - s_power() may be called via other paths,
> such as when the subdev is opened.

I don't think that is a problem, as long as power_count is working
as it should, and the caller from the other paths has not created an
imbalance.

Steve

[PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 02:09 PM, Russell King - ARM Linux wrote:
> On Sun, Mar 12, 2017 at 08:40:37PM +0000, Russell King - ARM Linux wrote:
>> On Sun, Mar 12, 2017 at 01:36:32PM -0700, Steve Longerbeam wrote:
>>> But hold on, if my logic is correct, then why did the CSI power-off
>>> get reached in your case, multiple times? Yes I think there is a bug,
>>> link_notify() is not checking if the link has already been disabled.
>>> I will fix this. But I'm surprised media core's link_notify handling
>>> doesn't do this.
>> Well, I think there's something incredibly fishy going on here.  I
>> turned that dev_dbg() at the top of the function into a dev_info(),
>> and I get:
>>
>> root at hbi2ex:~# dmesg |grep -A2 imx-ipuv3-csi
>> [   53.370949] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
>> [   53.371015] ------------[ cut here ]------------
>> [   53.371075] WARNING: CPU: 0 PID: 1515 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 [imx_media_csi]
>> --
>> [   53.372624] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
>> [   53.372637] ------------[ cut here ]------------
>> [   53.372663] WARNING: CPU: 0 PID: 1515 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 [imx_media_csi]
>>
>> There isn't a power on event being generated before these two power
>> off events.  I don't see a power on event even when I attempt to
>> start streaming either (which fails due to the lack of bayer
>> support.)
> Found it - my imx219 driver returns '1' from its s_power function when
> powering up, which triggers a bug in your code - when imx_media_set_power()
> fails to power up, you call imx_media_set_power() telling it to power
> everything off - including devices that are already powered off.

Yep, there's a bug in the error cleanup in imx_media_pipeline_set_power().
On error, it needs to backout by calling s_power(off) as it is doing, 
but not
through the whole pipeline, but needs to stop at the subdev encountered
just before the subdev that failed. This was causing the s_power() 
imbalance.
I will fix.


>
> This is really bad news - s_power() may be called via other paths,
> such as when the subdev is opened.

I don't think that is a problem, as long as power_count is working
as it should, and the caller from the other paths has not created an
imbalance.

Steve

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 02:09 PM, Russell King - ARM Linux wrote:
> On Sun, Mar 12, 2017 at 08:40:37PM +0000, Russell King - ARM Linux wrote:
>> On Sun, Mar 12, 2017 at 01:36:32PM -0700, Steve Longerbeam wrote:
>>> But hold on, if my logic is correct, then why did the CSI power-off
>>> get reached in your case, multiple times? Yes I think there is a bug,
>>> link_notify() is not checking if the link has already been disabled.
>>> I will fix this. But I'm surprised media core's link_notify handling
>>> doesn't do this.
>> Well, I think there's something incredibly fishy going on here.  I
>> turned that dev_dbg() at the top of the function into a dev_info(),
>> and I get:
>>
>> root@hbi2ex:~# dmesg |grep -A2 imx-ipuv3-csi
>> [   53.370949] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
>> [   53.371015] ------------[ cut here ]------------
>> [   53.371075] WARNING: CPU: 0 PID: 1515 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 [imx_media_csi]
>> --
>> [   53.372624] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
>> [   53.372637] ------------[ cut here ]------------
>> [   53.372663] WARNING: CPU: 0 PID: 1515 at drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 [imx_media_csi]
>>
>> There isn't a power on event being generated before these two power
>> off events.  I don't see a power on event even when I attempt to
>> start streaming either (which fails due to the lack of bayer
>> support.)
> Found it - my imx219 driver returns '1' from its s_power function when
> powering up, which triggers a bug in your code - when imx_media_set_power()
> fails to power up, you call imx_media_set_power() telling it to power
> everything off - including devices that are already powered off.

Yep, there's a bug in the error cleanup in imx_media_pipeline_set_power().
On error, it needs to backout by calling s_power(off) as it is doing, 
but not
through the whole pipeline, but needs to stop at the subdev encountered
just before the subdev that failed. This was causing the s_power() 
imbalance.
I will fix.


>
> This is really bad news - s_power() may be called via other paths,
> such as when the subdev is opened.

I don't think that is a problem, as long as power_count is working
as it should, and the caller from the other paths has not created an
imbalance.

Steve

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

Hi Russell,


On 03/14/2017 10:29 AM, Steve Longerbeam wrote:
>
>
> On 03/12/2017 02:09 PM, Russell King - ARM Linux wrote:
>> On Sun, Mar 12, 2017 at 08:40:37PM +0000, Russell King - ARM Linux 
>> wrote:
>>> On Sun, Mar 12, 2017 at 01:36:32PM -0700, Steve Longerbeam wrote:
>>>> But hold on, if my logic is correct, then why did the CSI power-off
>>>> get reached in your case, multiple times? Yes I think there is a bug,
>>>> link_notify() is not checking if the link has already been disabled.
>>>> I will fix this. But I'm surprised media core's link_notify handling
>>>> doesn't do this.
>>> Well, I think there's something incredibly fishy going on here.  I
>>> turned that dev_dbg() at the top of the function into a dev_info(),
>>> and I get:
>>>
>>> root@hbi2ex:~# dmesg |grep -A2 imx-ipuv3-csi
>>> [   53.370949] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
>>> [   53.371015] ------------[ cut here ]------------
>>> [   53.371075] WARNING: CPU: 0 PID: 1515 at 
>>> drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 
>>> [imx_media_csi]
>>> -- 
>>> [   53.372624] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
>>> [   53.372637] ------------[ cut here ]------------
>>> [   53.372663] WARNING: CPU: 0 PID: 1515 at 
>>> drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 
>>> [imx_media_csi]
>>>
>>> There isn't a power on event being generated before these two power
>>> off events.  I don't see a power on event even when I attempt to
>>> start streaming either (which fails due to the lack of bayer
>>> support.)
>> Found it - my imx219 driver returns '1' from its s_power function when
>> powering up, which triggers a bug in your code - when 
>> imx_media_set_power()
>> fails to power up, you call imx_media_set_power() telling it to power
>> everything off - including devices that are already powered off.
>
> Yep, there's a bug in the error cleanup in 
> imx_media_pipeline_set_power().
> On error, it needs to backout by calling s_power(off) as it is doing, 
> but not
> through the whole pipeline, but needs to stop at the subdev encountered
> just before the subdev that failed. This was causing the s_power() 
> imbalance.
> I will fix.
>

Due to some fixes to ov5640 from version 4, v4l2_pipeline_pm APIs are 
working
now, so I've removed imx_media_pipeline_set_power() and switched to
v4l2_pipeline_pm_use() in capture device open/release and 
v4l2_pipeline_link_notify()
in imx_media_link_notify(), for the pipeline power management.

Steve

[PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

Hi Russell,


On 03/14/2017 10:29 AM, Steve Longerbeam wrote:
>
>
> On 03/12/2017 02:09 PM, Russell King - ARM Linux wrote:
>> On Sun, Mar 12, 2017 at 08:40:37PM +0000, Russell King - ARM Linux 
>> wrote:
>>> On Sun, Mar 12, 2017 at 01:36:32PM -0700, Steve Longerbeam wrote:
>>>> But hold on, if my logic is correct, then why did the CSI power-off
>>>> get reached in your case, multiple times? Yes I think there is a bug,
>>>> link_notify() is not checking if the link has already been disabled.
>>>> I will fix this. But I'm surprised media core's link_notify handling
>>>> doesn't do this.
>>> Well, I think there's something incredibly fishy going on here.  I
>>> turned that dev_dbg() at the top of the function into a dev_info(),
>>> and I get:
>>>
>>> root at hbi2ex:~# dmesg |grep -A2 imx-ipuv3-csi
>>> [   53.370949] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
>>> [   53.371015] ------------[ cut here ]------------
>>> [   53.371075] WARNING: CPU: 0 PID: 1515 at 
>>> drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 
>>> [imx_media_csi]
>>> -- 
>>> [   53.372624] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
>>> [   53.372637] ------------[ cut here ]------------
>>> [   53.372663] WARNING: CPU: 0 PID: 1515 at 
>>> drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 
>>> [imx_media_csi]
>>>
>>> There isn't a power on event being generated before these two power
>>> off events.  I don't see a power on event even when I attempt to
>>> start streaming either (which fails due to the lack of bayer
>>> support.)
>> Found it - my imx219 driver returns '1' from its s_power function when
>> powering up, which triggers a bug in your code - when 
>> imx_media_set_power()
>> fails to power up, you call imx_media_set_power() telling it to power
>> everything off - including devices that are already powered off.
>
> Yep, there's a bug in the error cleanup in 
> imx_media_pipeline_set_power().
> On error, it needs to backout by calling s_power(off) as it is doing, 
> but not
> through the whole pipeline, but needs to stop at the subdev encountered
> just before the subdev that failed. This was causing the s_power() 
> imbalance.
> I will fix.
>

Due to some fixes to ov5640 from version 4, v4l2_pipeline_pm APIs are 
working
now, so I've removed imx_media_pipeline_set_power() and switched to
v4l2_pipeline_pm_use() in capture device open/release and 
v4l2_pipeline_link_notify()
in imx_media_link_notify(), for the pipeline power management.

Steve

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

Hi Russell,


On 03/14/2017 10:29 AM, Steve Longerbeam wrote:
>
>
> On 03/12/2017 02:09 PM, Russell King - ARM Linux wrote:
>> On Sun, Mar 12, 2017 at 08:40:37PM +0000, Russell King - ARM Linux 
>> wrote:
>>> On Sun, Mar 12, 2017 at 01:36:32PM -0700, Steve Longerbeam wrote:
>>>> But hold on, if my logic is correct, then why did the CSI power-off
>>>> get reached in your case, multiple times? Yes I think there is a bug,
>>>> link_notify() is not checking if the link has already been disabled.
>>>> I will fix this. But I'm surprised media core's link_notify handling
>>>> doesn't do this.
>>> Well, I think there's something incredibly fishy going on here.  I
>>> turned that dev_dbg() at the top of the function into a dev_info(),
>>> and I get:
>>>
>>> root@hbi2ex:~# dmesg |grep -A2 imx-ipuv3-csi
>>> [   53.370949] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
>>> [   53.371015] ------------[ cut here ]------------
>>> [   53.371075] WARNING: CPU: 0 PID: 1515 at 
>>> drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 
>>> [imx_media_csi]
>>> -- 
>>> [   53.372624] imx-ipuv3-csi imx-ipuv3-csi.0: power OFF
>>> [   53.372637] ------------[ cut here ]------------
>>> [   53.372663] WARNING: CPU: 0 PID: 1515 at 
>>> drivers/staging/media/imx/imx-media-csi.c:806 csi_s_power+0xb8/0xd0 
>>> [imx_media_csi]
>>>
>>> There isn't a power on event being generated before these two power
>>> off events.  I don't see a power on event even when I attempt to
>>> start streaming either (which fails due to the lack of bayer
>>> support.)
>> Found it - my imx219 driver returns '1' from its s_power function when
>> powering up, which triggers a bug in your code - when 
>> imx_media_set_power()
>> fails to power up, you call imx_media_set_power() telling it to power
>> everything off - including devices that are already powered off.
>
> Yep, there's a bug in the error cleanup in 
> imx_media_pipeline_set_power().
> On error, it needs to backout by calling s_power(off) as it is doing, 
> but not
> through the whole pipeline, but needs to stop at the subdev encountered
> just before the subdev that failed. This was causing the s_power() 
> imbalance.
> I will fix.
>

Due to some fixes to ov5640 from version 4, v4l2_pipeline_pm APIs are 
working
now, so I've removed imx_media_pipeline_set_power() and switched to
v4l2_pipeline_pm_use() in capture device open/release and 
v4l2_pipeline_link_notify()
in imx_media_link_notify(), for the pipeline power management.

Steve

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

Another issue.

The "reboot and the /dev/video* devices come up in a completely
different order" problem seems to exist with this version.

The dot graph I supplied previously had "ipu1_csi0 capture" on
/dev/video4.  I've just rebooted, and now I find it's on
/dev/video2 instead.

Here's the extract from the .dot file of the old listing:

        n00000018 [label="ipu1_ic_prpenc capture\n/dev/video0", shape=box, style=filled, fillcolor=yellow]
        n00000021 [label="ipu1_ic_prpvf capture\n/dev/video1", shape=box, style=filled, fillcolor=yellow]
        n0000002e [label="ipu2_ic_prpenc capture\n/dev/video2", shape=box, style=filled, fillcolor=yellow]
        n00000037 [label="ipu2_ic_prpvf capture\n/dev/video3", shape=box, style=filled, fillcolor=yellow]
        n00000048 [label="ipu1_csi0 capture\n/dev/video4", shape=box, style=filled, fillcolor=yellow]
        n00000052 [label="ipu1_csi1 capture\n/dev/video5", shape=box, style=filled, fillcolor=yellow]
        n00000062 [label="ipu2_csi0 capture\n/dev/video6", shape=box, style=filled, fillcolor=yellow]
        n0000006c [label="ipu2_csi1 capture\n/dev/video7", shape=box, style=filled, fillcolor=yellow]

and here's the same after reboot:

        n00000014 [label="ipu1_csi0 capture\n/dev/video2", shape=box, style=filled, fillcolor=yellow]
        n0000001e [label="ipu1_csi1 capture\n/dev/video3", shape=box, style=filled, fillcolor=yellow]
        n00000028 [label="ipu2_csi0 capture\n/dev/video4", shape=box, style=filled, fillcolor=yellow]
        n00000035 [label="ipu1_ic_prpenc capture\n/dev/video5", shape=box, style=filled, fillcolor=yellow]
        n0000003e [label="ipu1_ic_prpvf capture\n/dev/video6", shape=box, style=filled, fillcolor=yellow]
        n0000004c [label="ipu2_csi1 capture\n/dev/video7", shape=box, style=filled, fillcolor=yellow]
        n00000059 [label="ipu2_ic_prpenc capture\n/dev/video8", shape=box, style=filled, fillcolor=yellow]
        n00000062 [label="ipu2_ic_prpvf capture\n/dev/video9", shape=box, style=filled, fillcolor=yellow]

(/dev/video0 and /dev/video1 are taken up by CODA, since I updated the
names of the firmware files, and now CODA initialises... seems the
back-compat filenames don't work, but that's not a problem with imx6
capture.)

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

Another issue.

The "reboot and the /dev/video* devices come up in a completely
different order" problem seems to exist with this version.

The dot graph I supplied previously had "ipu1_csi0 capture" on
/dev/video4.  I've just rebooted, and now I find it's on
/dev/video2 instead.

Here's the extract from the .dot file of the old listing:

        n00000018 [label="ipu1_ic_prpenc capture\n/dev/video0", shape=box, style=filled, fillcolor=yellow]
        n00000021 [label="ipu1_ic_prpvf capture\n/dev/video1", shape=box, style=filled, fillcolor=yellow]
        n0000002e [label="ipu2_ic_prpenc capture\n/dev/video2", shape=box, style=filled, fillcolor=yellow]
        n00000037 [label="ipu2_ic_prpvf capture\n/dev/video3", shape=box, style=filled, fillcolor=yellow]
        n00000048 [label="ipu1_csi0 capture\n/dev/video4", shape=box, style=filled, fillcolor=yellow]
        n00000052 [label="ipu1_csi1 capture\n/dev/video5", shape=box, style=filled, fillcolor=yellow]
        n00000062 [label="ipu2_csi0 capture\n/dev/video6", shape=box, style=filled, fillcolor=yellow]
        n0000006c [label="ipu2_csi1 capture\n/dev/video7", shape=box, style=filled, fillcolor=yellow]

and here's the same after reboot:

        n00000014 [label="ipu1_csi0 capture\n/dev/video2", shape=box, style=filled, fillcolor=yellow]
        n0000001e [label="ipu1_csi1 capture\n/dev/video3", shape=box, style=filled, fillcolor=yellow]
        n00000028 [label="ipu2_csi0 capture\n/dev/video4", shape=box, style=filled, fillcolor=yellow]
        n00000035 [label="ipu1_ic_prpenc capture\n/dev/video5", shape=box, style=filled, fillcolor=yellow]
        n0000003e [label="ipu1_ic_prpvf capture\n/dev/video6", shape=box, style=filled, fillcolor=yellow]
        n0000004c [label="ipu2_csi1 capture\n/dev/video7", shape=box, style=filled, fillcolor=yellow]
        n00000059 [label="ipu2_ic_prpenc capture\n/dev/video8", shape=box, style=filled, fillcolor=yellow]
        n00000062 [label="ipu2_ic_prpvf capture\n/dev/video9", shape=box, style=filled, fillcolor=yellow]

(/dev/video0 and /dev/video1 are taken up by CODA, since I updated the
names of the firmware files, and now CODA initialises... seems the
back-compat filenames don't work, but that's not a problem with imx6
capture.)

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

Another issue.

The "reboot and the /dev/video* devices come up in a completely
different order" problem seems to exist with this version.

The dot graph I supplied previously had "ipu1_csi0 capture" on
/dev/video4.  I've just rebooted, and now I find it's on
/dev/video2 instead.

Here's the extract from the .dot file of the old listing:

        n00000018 [label="ipu1_ic_prpenc capture\n/dev/video0", shape=box, style=filled, fillcolor=yellow]
        n00000021 [label="ipu1_ic_prpvf capture\n/dev/video1", shape=box, style=filled, fillcolor=yellow]
        n0000002e [label="ipu2_ic_prpenc capture\n/dev/video2", shape=box, style=filled, fillcolor=yellow]
        n00000037 [label="ipu2_ic_prpvf capture\n/dev/video3", shape=box, style=filled, fillcolor=yellow]
        n00000048 [label="ipu1_csi0 capture\n/dev/video4", shape=box, style=filled, fillcolor=yellow]
        n00000052 [label="ipu1_csi1 capture\n/dev/video5", shape=box, style=filled, fillcolor=yellow]
        n00000062 [label="ipu2_csi0 capture\n/dev/video6", shape=box, style=filled, fillcolor=yellow]
        n0000006c [label="ipu2_csi1 capture\n/dev/video7", shape=box, style=filled, fillcolor=yellow]

and here's the same after reboot:

        n00000014 [label="ipu1_csi0 capture\n/dev/video2", shape=box, style=filled, fillcolor=yellow]
        n0000001e [label="ipu1_csi1 capture\n/dev/video3", shape=box, style=filled, fillcolor=yellow]
        n00000028 [label="ipu2_csi0 capture\n/dev/video4", shape=box, style=filled, fillcolor=yellow]
        n00000035 [label="ipu1_ic_prpenc capture\n/dev/video5", shape=box, style=filled, fillcolor=yellow]
        n0000003e [label="ipu1_ic_prpvf capture\n/dev/video6", shape=box, style=filled, fillcolor=yellow]
        n0000004c [label="ipu2_csi1 capture\n/dev/video7", shape=box, style=filled, fillcolor=yellow]
        n00000059 [label="ipu2_ic_prpenc capture\n/dev/video8", shape=box, style=filled, fillcolor=yellow]
        n00000062 [label="ipu2_ic_prpvf capture\n/dev/video9", shape=box, style=filled, fillcolor=yellow]

(/dev/video0 and /dev/video1 are taken up by CODA, since I updated the
names of the firmware files, and now CODA initialises... seems the
back-compat filenames don't work, but that's not a problem with imx6
capture.)

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 12:47 PM, Russell King - ARM Linux wrote:
> Another issue.
>
> The "reboot and the /dev/video* devices come up in a completely
> different order" problem seems to exist with this version.
>
> The dot graph I supplied previously had "ipu1_csi0 capture" on
> /dev/video4.  I've just rebooted, and now I find it's on
> /dev/video2 instead.

Yes, that's still an issue I haven't had the chance to get to
yet.

It could be as simple as passing a fixed device node # to
video_register_device(), but something tells me it won't be
that easy. But I'll get to this in next version.

Steve

>
> Here's the extract from the .dot file of the old listing:
>
>         n00000018 [label="ipu1_ic_prpenc capture\n/dev/video0", shape=box, style=filled, fillcolor=yellow]
>         n00000021 [label="ipu1_ic_prpvf capture\n/dev/video1", shape=box, style=filled, fillcolor=yellow]
>         n0000002e [label="ipu2_ic_prpenc capture\n/dev/video2", shape=box, style=filled, fillcolor=yellow]
>         n00000037 [label="ipu2_ic_prpvf capture\n/dev/video3", shape=box, style=filled, fillcolor=yellow]
>         n00000048 [label="ipu1_csi0 capture\n/dev/video4", shape=box, style=filled, fillcolor=yellow]
>         n00000052 [label="ipu1_csi1 capture\n/dev/video5", shape=box, style=filled, fillcolor=yellow]
>         n00000062 [label="ipu2_csi0 capture\n/dev/video6", shape=box, style=filled, fillcolor=yellow]
>         n0000006c [label="ipu2_csi1 capture\n/dev/video7", shape=box, style=filled, fillcolor=yellow]
>
> and here's the same after reboot:
>
>         n00000014 [label="ipu1_csi0 capture\n/dev/video2", shape=box, style=filled, fillcolor=yellow]
>         n0000001e [label="ipu1_csi1 capture\n/dev/video3", shape=box, style=filled, fillcolor=yellow]
>         n00000028 [label="ipu2_csi0 capture\n/dev/video4", shape=box, style=filled, fillcolor=yellow]
>         n00000035 [label="ipu1_ic_prpenc capture\n/dev/video5", shape=box, style=filled, fillcolor=yellow]
>         n0000003e [label="ipu1_ic_prpvf capture\n/dev/video6", shape=box, style=filled, fillcolor=yellow]
>         n0000004c [label="ipu2_csi1 capture\n/dev/video7", shape=box, style=filled, fillcolor=yellow]
>         n00000059 [label="ipu2_ic_prpenc capture\n/dev/video8", shape=box, style=filled, fillcolor=yellow]
>         n00000062 [label="ipu2_ic_prpvf capture\n/dev/video9", shape=box, style=filled, fillcolor=yellow]
>
> (/dev/video0 and /dev/video1 are taken up by CODA, since I updated the
> names of the firmware files, and now CODA initialises... seems the
> back-compat filenames don't work, but that's not a problem with imx6
> capture.)
>

[PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 12:47 PM, Russell King - ARM Linux wrote:
> Another issue.
>
> The "reboot and the /dev/video* devices come up in a completely
> different order" problem seems to exist with this version.
>
> The dot graph I supplied previously had "ipu1_csi0 capture" on
> /dev/video4.  I've just rebooted, and now I find it's on
> /dev/video2 instead.

Yes, that's still an issue I haven't had the chance to get to
yet.

It could be as simple as passing a fixed device node # to
video_register_device(), but something tells me it won't be
that easy. But I'll get to this in next version.

Steve

>
> Here's the extract from the .dot file of the old listing:
>
>         n00000018 [label="ipu1_ic_prpenc capture\n/dev/video0", shape=box, style=filled, fillcolor=yellow]
>         n00000021 [label="ipu1_ic_prpvf capture\n/dev/video1", shape=box, style=filled, fillcolor=yellow]
>         n0000002e [label="ipu2_ic_prpenc capture\n/dev/video2", shape=box, style=filled, fillcolor=yellow]
>         n00000037 [label="ipu2_ic_prpvf capture\n/dev/video3", shape=box, style=filled, fillcolor=yellow]
>         n00000048 [label="ipu1_csi0 capture\n/dev/video4", shape=box, style=filled, fillcolor=yellow]
>         n00000052 [label="ipu1_csi1 capture\n/dev/video5", shape=box, style=filled, fillcolor=yellow]
>         n00000062 [label="ipu2_csi0 capture\n/dev/video6", shape=box, style=filled, fillcolor=yellow]
>         n0000006c [label="ipu2_csi1 capture\n/dev/video7", shape=box, style=filled, fillcolor=yellow]
>
> and here's the same after reboot:
>
>         n00000014 [label="ipu1_csi0 capture\n/dev/video2", shape=box, style=filled, fillcolor=yellow]
>         n0000001e [label="ipu1_csi1 capture\n/dev/video3", shape=box, style=filled, fillcolor=yellow]
>         n00000028 [label="ipu2_csi0 capture\n/dev/video4", shape=box, style=filled, fillcolor=yellow]
>         n00000035 [label="ipu1_ic_prpenc capture\n/dev/video5", shape=box, style=filled, fillcolor=yellow]
>         n0000003e [label="ipu1_ic_prpvf capture\n/dev/video6", shape=box, style=filled, fillcolor=yellow]
>         n0000004c [label="ipu2_csi1 capture\n/dev/video7", shape=box, style=filled, fillcolor=yellow]
>         n00000059 [label="ipu2_ic_prpenc capture\n/dev/video8", shape=box, style=filled, fillcolor=yellow]
>         n00000062 [label="ipu2_ic_prpvf capture\n/dev/video9", shape=box, style=filled, fillcolor=yellow]
>
> (/dev/video0 and /dev/video1 are taken up by CODA, since I updated the
> names of the firmware files, and now CODA initialises... seems the
> back-compat filenames don't work, but that's not a problem with imx6
> capture.)
>

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 12:47 PM, Russell King - ARM Linux wrote:
> Another issue.
>
> The "reboot and the /dev/video* devices come up in a completely
> different order" problem seems to exist with this version.
>
> The dot graph I supplied previously had "ipu1_csi0 capture" on
> /dev/video4.  I've just rebooted, and now I find it's on
> /dev/video2 instead.

Yes, that's still an issue I haven't had the chance to get to
yet.

It could be as simple as passing a fixed device node # to
video_register_device(), but something tells me it won't be
that easy. But I'll get to this in next version.

Steve

>
> Here's the extract from the .dot file of the old listing:
>
>         n00000018 [label="ipu1_ic_prpenc capture\n/dev/video0", shape=box, style=filled, fillcolor=yellow]
>         n00000021 [label="ipu1_ic_prpvf capture\n/dev/video1", shape=box, style=filled, fillcolor=yellow]
>         n0000002e [label="ipu2_ic_prpenc capture\n/dev/video2", shape=box, style=filled, fillcolor=yellow]
>         n00000037 [label="ipu2_ic_prpvf capture\n/dev/video3", shape=box, style=filled, fillcolor=yellow]
>         n00000048 [label="ipu1_csi0 capture\n/dev/video4", shape=box, style=filled, fillcolor=yellow]
>         n00000052 [label="ipu1_csi1 capture\n/dev/video5", shape=box, style=filled, fillcolor=yellow]
>         n00000062 [label="ipu2_csi0 capture\n/dev/video6", shape=box, style=filled, fillcolor=yellow]
>         n0000006c [label="ipu2_csi1 capture\n/dev/video7", shape=box, style=filled, fillcolor=yellow]
>
> and here's the same after reboot:
>
>         n00000014 [label="ipu1_csi0 capture\n/dev/video2", shape=box, style=filled, fillcolor=yellow]
>         n0000001e [label="ipu1_csi1 capture\n/dev/video3", shape=box, style=filled, fillcolor=yellow]
>         n00000028 [label="ipu2_csi0 capture\n/dev/video4", shape=box, style=filled, fillcolor=yellow]
>         n00000035 [label="ipu1_ic_prpenc capture\n/dev/video5", shape=box, style=filled, fillcolor=yellow]
>         n0000003e [label="ipu1_ic_prpvf capture\n/dev/video6", shape=box, style=filled, fillcolor=yellow]
>         n0000004c [label="ipu2_csi1 capture\n/dev/video7", shape=box, style=filled, fillcolor=yellow]
>         n00000059 [label="ipu2_ic_prpenc capture\n/dev/video8", shape=box, style=filled, fillcolor=yellow]
>         n00000062 [label="ipu2_ic_prpvf capture\n/dev/video9", shape=box, style=filled, fillcolor=yellow]
>
> (/dev/video0 and /dev/video1 are taken up by CODA, since I updated the
> names of the firmware files, and now CODA initialises... seems the
> back-compat filenames don't work, but that's not a problem with imx6
> capture.)
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 00/39] i.MX Media Driver

[Mauro Carvalho Chehab]

Em Sun, 12 Mar 2017 19:47:00 +0000
Russell King - ARM Linux <linux@armlinux.org.uk> escreveu:

> Another issue.
> 
> The "reboot and the /dev/video* devices come up in a completely
> different order" problem seems to exist with this version.
> 
> The dot graph I supplied previously had "ipu1_csi0 capture" on
> /dev/video4.  I've just rebooted, and now I find it's on
> /dev/video2 instead.
> 
> Here's the extract from the .dot file of the old listing:
> 
>         n00000018 [label="ipu1_ic_prpenc capture\n/dev/video0", shape=box, style=filled, fillcolor=yellow]
>         n00000021 [label="ipu1_ic_prpvf capture\n/dev/video1", shape=box, style=filled, fillcolor=yellow]
>         n0000002e [label="ipu2_ic_prpenc capture\n/dev/video2", shape=box, style=filled, fillcolor=yellow]
>         n00000037 [label="ipu2_ic_prpvf capture\n/dev/video3", shape=box, style=filled, fillcolor=yellow]
>         n00000048 [label="ipu1_csi0 capture\n/dev/video4", shape=box, style=filled, fillcolor=yellow]
>         n00000052 [label="ipu1_csi1 capture\n/dev/video5", shape=box, style=filled, fillcolor=yellow]
>         n00000062 [label="ipu2_csi0 capture\n/dev/video6", shape=box, style=filled, fillcolor=yellow]
>         n0000006c [label="ipu2_csi1 capture\n/dev/video7", shape=box, style=filled, fillcolor=yellow]
> 
> and here's the same after reboot:
> 
>         n00000014 [label="ipu1_csi0 capture\n/dev/video2", shape=box, style=filled, fillcolor=yellow]
>         n0000001e [label="ipu1_csi1 capture\n/dev/video3", shape=box, style=filled, fillcolor=yellow]
>         n00000028 [label="ipu2_csi0 capture\n/dev/video4", shape=box, style=filled, fillcolor=yellow]
>         n00000035 [label="ipu1_ic_prpenc capture\n/dev/video5", shape=box, style=filled, fillcolor=yellow]
>         n0000003e [label="ipu1_ic_prpvf capture\n/dev/video6", shape=box, style=filled, fillcolor=yellow]
>         n0000004c [label="ipu2_csi1 capture\n/dev/video7", shape=box, style=filled, fillcolor=yellow]
>         n00000059 [label="ipu2_ic_prpenc capture\n/dev/video8", shape=box, style=filled, fillcolor=yellow]
>         n00000062 [label="ipu2_ic_prpvf capture\n/dev/video9", shape=box, style=filled, fillcolor=yellow]
> 
> (/dev/video0 and /dev/video1 are taken up by CODA, since I updated the
> names of the firmware files, and now CODA initialises... seems the
> back-compat filenames don't work, but that's not a problem with imx6
> capture.)
> 

Didn't have time yet to read/comment the other e-mails in this thread.

Yet, as this is a simple issue, let me answer it first.

With regards to /dev/video?, the device number depends on the probing 
order, with can be random on SoC drivers, due to the way OF works. 

Yet, udev/systemd has some rules that provide an unique name for V4L
devices at /lib/udev/rules.d/60-persistent-v4l.rules. Basically, it
runs a small application (v4l_id) with creates a persistent symling
using rules like this:

	KERNEL=="video*", ENV{ID_SERIAL}=="?*", SYMLINK+="v4l/by-id/$env{ID_BUS}-$env{ID_SERIAL}-video-index$attr{index}"

Those names are stored at /dev/v4l/by-path.

For example, on Exynos, we have:

$ ls -lctra /dev/v4l/by-path/
total 0
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-13e10000.video-scaler-video-index0 -> ../../video7
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-13e00000.video-scaler-video-index0 -> ../../video6
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-11f60000.jpeg-video-index0 -> ../../video4
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-11f50000.jpeg-video-index1 -> ../../video3
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-11f50000.jpeg-video-index0 -> ../../video2
drwxr-xr-x 3 root root  60 Mar 11 07:19 ..
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-11f60000.jpeg-video-index1 -> ../../video5
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-11000000.codec-video-index1 -> ../../video1
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-11000000.codec-video-index0 -> ../../video0

No matter what driver gets probed first, the above names should not
change.

So, if you want to write a script, the best is to use the /dev/v4l/by-path.

Unfortunately, gstreamer has some issues with that, as some of their plugins
don't seem to allow passing the name of the devnode, but just the number of
/dev/video?.

So, you need some script to convert from /dev/v4l/by-path/foo to
/dev/video?.

What I'm using on Exynos scripts is this logic:

	NEEDED1=platform-13e00000.video-scaler-video-index0
	DEV1=$(ls -l /dev/v4l/by-path/$NEEDED1|perl -ne ' print $1 if (m,/video(\d+),)')

Then, if I need to talk with this mem2mem driver using the v4l2video
convert plugin, I can launch gst with something like:

	gst-launch-1.0 videotestsrc ! v4l2video${DEV1}convert ! fakesink

Thanks,
Mauro


Thanks,
Mauro

[PATCH v5 00/39] i.MX Media Driver

[Mauro Carvalho Chehab]

Em Sun, 12 Mar 2017 19:47:00 +0000
Russell King - ARM Linux <linux@armlinux.org.uk> escreveu:

> Another issue.
> 
> The "reboot and the /dev/video* devices come up in a completely
> different order" problem seems to exist with this version.
> 
> The dot graph I supplied previously had "ipu1_csi0 capture" on
> /dev/video4.  I've just rebooted, and now I find it's on
> /dev/video2 instead.
> 
> Here's the extract from the .dot file of the old listing:
> 
>         n00000018 [label="ipu1_ic_prpenc capture\n/dev/video0", shape=box, style=filled, fillcolor=yellow]
>         n00000021 [label="ipu1_ic_prpvf capture\n/dev/video1", shape=box, style=filled, fillcolor=yellow]
>         n0000002e [label="ipu2_ic_prpenc capture\n/dev/video2", shape=box, style=filled, fillcolor=yellow]
>         n00000037 [label="ipu2_ic_prpvf capture\n/dev/video3", shape=box, style=filled, fillcolor=yellow]
>         n00000048 [label="ipu1_csi0 capture\n/dev/video4", shape=box, style=filled, fillcolor=yellow]
>         n00000052 [label="ipu1_csi1 capture\n/dev/video5", shape=box, style=filled, fillcolor=yellow]
>         n00000062 [label="ipu2_csi0 capture\n/dev/video6", shape=box, style=filled, fillcolor=yellow]
>         n0000006c [label="ipu2_csi1 capture\n/dev/video7", shape=box, style=filled, fillcolor=yellow]
> 
> and here's the same after reboot:
> 
>         n00000014 [label="ipu1_csi0 capture\n/dev/video2", shape=box, style=filled, fillcolor=yellow]
>         n0000001e [label="ipu1_csi1 capture\n/dev/video3", shape=box, style=filled, fillcolor=yellow]
>         n00000028 [label="ipu2_csi0 capture\n/dev/video4", shape=box, style=filled, fillcolor=yellow]
>         n00000035 [label="ipu1_ic_prpenc capture\n/dev/video5", shape=box, style=filled, fillcolor=yellow]
>         n0000003e [label="ipu1_ic_prpvf capture\n/dev/video6", shape=box, style=filled, fillcolor=yellow]
>         n0000004c [label="ipu2_csi1 capture\n/dev/video7", shape=box, style=filled, fillcolor=yellow]
>         n00000059 [label="ipu2_ic_prpenc capture\n/dev/video8", shape=box, style=filled, fillcolor=yellow]
>         n00000062 [label="ipu2_ic_prpvf capture\n/dev/video9", shape=box, style=filled, fillcolor=yellow]
> 
> (/dev/video0 and /dev/video1 are taken up by CODA, since I updated the
> names of the firmware files, and now CODA initialises... seems the
> back-compat filenames don't work, but that's not a problem with imx6
> capture.)
> 

Didn't have time yet to read/comment the other e-mails in this thread.

Yet, as this is a simple issue, let me answer it first.

With regards to /dev/video?, the device number depends on the probing 
order, with can be random on SoC drivers, due to the way OF works. 

Yet, udev/systemd has some rules that provide an unique name for V4L
devices at /lib/udev/rules.d/60-persistent-v4l.rules. Basically, it
runs a small application (v4l_id) with creates a persistent symling
using rules like this:

	KERNEL=="video*", ENV{ID_SERIAL}=="?*", SYMLINK+="v4l/by-id/$env{ID_BUS}-$env{ID_SERIAL}-video-index$attr{index}"

Those names are stored at /dev/v4l/by-path.

For example, on Exynos, we have:

$ ls -lctra /dev/v4l/by-path/
total 0
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-13e10000.video-scaler-video-index0 -> ../../video7
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-13e00000.video-scaler-video-index0 -> ../../video6
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-11f60000.jpeg-video-index0 -> ../../video4
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-11f50000.jpeg-video-index1 -> ../../video3
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-11f50000.jpeg-video-index0 -> ../../video2
drwxr-xr-x 3 root root  60 Mar 11 07:19 ..
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-11f60000.jpeg-video-index1 -> ../../video5
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-11000000.codec-video-index1 -> ../../video1
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-11000000.codec-video-index0 -> ../../video0

No matter what driver gets probed first, the above names should not
change.

So, if you want to write a script, the best is to use the /dev/v4l/by-path.

Unfortunately, gstreamer has some issues with that, as some of their plugins
don't seem to allow passing the name of the devnode, but just the number of
/dev/video?.

So, you need some script to convert from /dev/v4l/by-path/foo to
/dev/video?.

What I'm using on Exynos scripts is this logic:

	NEEDED1=platform-13e00000.video-scaler-video-index0
	DEV1=$(ls -l /dev/v4l/by-path/$NEEDED1|perl -ne ' print $1 if (m,/video(\d+),)')

Then, if I need to talk with this mem2mem driver using the v4l2video
convert plugin, I can launch gst with something like:

	gst-launch-1.0 videotestsrc ! v4l2video${DEV1}convert ! fakesink

Thanks,
Mauro


Thanks,
Mauro

Re: [PATCH v5 00/39] i.MX Media Driver

[Mauro Carvalho Chehab]

Em Sun, 12 Mar 2017 19:47:00 +0000
Russell King - ARM Linux <linux-I+IVW8TIWO2tmTQ+vhA3Yw@public.gmane.org> escreveu:

> Another issue.
> 
> The "reboot and the /dev/video* devices come up in a completely
> different order" problem seems to exist with this version.
> 
> The dot graph I supplied previously had "ipu1_csi0 capture" on
> /dev/video4.  I've just rebooted, and now I find it's on
> /dev/video2 instead.
> 
> Here's the extract from the .dot file of the old listing:
> 
>         n00000018 [label="ipu1_ic_prpenc capture\n/dev/video0", shape=box, style=filled, fillcolor=yellow]
>         n00000021 [label="ipu1_ic_prpvf capture\n/dev/video1", shape=box, style=filled, fillcolor=yellow]
>         n0000002e [label="ipu2_ic_prpenc capture\n/dev/video2", shape=box, style=filled, fillcolor=yellow]
>         n00000037 [label="ipu2_ic_prpvf capture\n/dev/video3", shape=box, style=filled, fillcolor=yellow]
>         n00000048 [label="ipu1_csi0 capture\n/dev/video4", shape=box, style=filled, fillcolor=yellow]
>         n00000052 [label="ipu1_csi1 capture\n/dev/video5", shape=box, style=filled, fillcolor=yellow]
>         n00000062 [label="ipu2_csi0 capture\n/dev/video6", shape=box, style=filled, fillcolor=yellow]
>         n0000006c [label="ipu2_csi1 capture\n/dev/video7", shape=box, style=filled, fillcolor=yellow]
> 
> and here's the same after reboot:
> 
>         n00000014 [label="ipu1_csi0 capture\n/dev/video2", shape=box, style=filled, fillcolor=yellow]
>         n0000001e [label="ipu1_csi1 capture\n/dev/video3", shape=box, style=filled, fillcolor=yellow]
>         n00000028 [label="ipu2_csi0 capture\n/dev/video4", shape=box, style=filled, fillcolor=yellow]
>         n00000035 [label="ipu1_ic_prpenc capture\n/dev/video5", shape=box, style=filled, fillcolor=yellow]
>         n0000003e [label="ipu1_ic_prpvf capture\n/dev/video6", shape=box, style=filled, fillcolor=yellow]
>         n0000004c [label="ipu2_csi1 capture\n/dev/video7", shape=box, style=filled, fillcolor=yellow]
>         n00000059 [label="ipu2_ic_prpenc capture\n/dev/video8", shape=box, style=filled, fillcolor=yellow]
>         n00000062 [label="ipu2_ic_prpvf capture\n/dev/video9", shape=box, style=filled, fillcolor=yellow]
> 
> (/dev/video0 and /dev/video1 are taken up by CODA, since I updated the
> names of the firmware files, and now CODA initialises... seems the
> back-compat filenames don't work, but that's not a problem with imx6
> capture.)
> 

Didn't have time yet to read/comment the other e-mails in this thread.

Yet, as this is a simple issue, let me answer it first.

With regards to /dev/video?, the device number depends on the probing 
order, with can be random on SoC drivers, due to the way OF works. 

Yet, udev/systemd has some rules that provide an unique name for V4L
devices at /lib/udev/rules.d/60-persistent-v4l.rules. Basically, it
runs a small application (v4l_id) with creates a persistent symling
using rules like this:

	KERNEL=="video*", ENV{ID_SERIAL}=="?*", SYMLINK+="v4l/by-id/$env{ID_BUS}-$env{ID_SERIAL}-video-index$attr{index}"

Those names are stored at /dev/v4l/by-path.

For example, on Exynos, we have:

$ ls -lctra /dev/v4l/by-path/
total 0
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-13e10000.video-scaler-video-index0 -> ../../video7
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-13e00000.video-scaler-video-index0 -> ../../video6
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-11f60000.jpeg-video-index0 -> ../../video4
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-11f50000.jpeg-video-index1 -> ../../video3
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-11f50000.jpeg-video-index0 -> ../../video2
drwxr-xr-x 3 root root  60 Mar 11 07:19 ..
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-11f60000.jpeg-video-index1 -> ../../video5
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-11000000.codec-video-index1 -> ../../video1
lrwxrwxrwx 1 root root  12 Mar 11 07:19 platform-11000000.codec-video-index0 -> ../../video0

No matter what driver gets probed first, the above names should not
change.

So, if you want to write a script, the best is to use the /dev/v4l/by-path.

Unfortunately, gstreamer has some issues with that, as some of their plugins
don't seem to allow passing the name of the devnode, but just the number of
/dev/video?.

So, you need some script to convert from /dev/v4l/by-path/foo to
/dev/video?.

What I'm using on Exynos scripts is this logic:

	NEEDED1=platform-13e00000.video-scaler-video-index0
	DEV1=$(ls -l /dev/v4l/by-path/$NEEDED1|perl -ne ' print $1 if (m,/video(\d+),)')

Then, if I need to talk with this mem2mem driver using the v4l2video
convert plugin, I can launch gst with something like:

	gst-launch-1.0 videotestsrc ! v4l2video${DEV1}convert ! fakesink

Thanks,
Mauro


Thanks,
Mauro
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 12, 2017 at 05:59:28PM -0300, Mauro Carvalho Chehab wrote:
> Yet, udev/systemd has some rules that provide an unique name for V4L
> devices at /lib/udev/rules.d/60-persistent-v4l.rules. Basically, it
> runs a small application (v4l_id) with creates a persistent symling
> using rules like this:
> 
> 	KERNEL=="video*", ENV{ID_SERIAL}=="?*", SYMLINK+="v4l/by-id/$env{ID_BUS}-$env{ID_SERIAL}-video-index$attr{index}"
> 
> Those names are stored at /dev/v4l/by-path.

This doesn't help:

$ ls -Al /dev/v4l/by-id/
total 0
lrwxrwxrwx 1 root root 13 Mar 12 19:54 usb-Sonix_Technology_Co.__Ltd._USB_2.0_Camera-video-index0 -> ../../video10
$ ls -Al /dev/v4l/by-path/
total 0
lrwxrwxrwx 1 root root 12 Mar 12 19:54 platform-2040000.vpu-video-index0 -> ../../video0
lrwxrwxrwx 1 root root 12 Mar 12 19:54 platform-2040000.vpu-video-index1 -> ../../video1
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index0 -> ../../video2
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index1 -> ../../video3
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index2 -> ../../video4
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index3 -> ../../video5
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index4 -> ../../video6
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index5 -> ../../video7
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index6 -> ../../video8
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index7 -> ../../video9
lrwxrwxrwx 1 root root 13 Mar 12 19:54 platform-ci_hdrc.0-usb-0:1:1.0-video-index0 -> ../../video10

The problem is the "platform-capture-subsystem-video-index" entries.
These themselves change order.  For instance, I now have:

- entity 72: ipu1_csi0 capture (1 pad, 1 link)
             type Node subtype V4L flags 0
             device node name /dev/video6

which means it's platform-capture-subsystem-video-index4.  Before, it
was platform-capture-subsystem-video-index2.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 12, 2017 at 05:59:28PM -0300, Mauro Carvalho Chehab wrote:
> Yet, udev/systemd has some rules that provide an unique name for V4L
> devices at /lib/udev/rules.d/60-persistent-v4l.rules. Basically, it
> runs a small application (v4l_id) with creates a persistent symling
> using rules like this:
> 
> 	KERNEL=="video*", ENV{ID_SERIAL}=="?*", SYMLINK+="v4l/by-id/$env{ID_BUS}-$env{ID_SERIAL}-video-index$attr{index}"
> 
> Those names are stored at /dev/v4l/by-path.

This doesn't help:

$ ls -Al /dev/v4l/by-id/
total 0
lrwxrwxrwx 1 root root 13 Mar 12 19:54 usb-Sonix_Technology_Co.__Ltd._USB_2.0_Camera-video-index0 -> ../../video10
$ ls -Al /dev/v4l/by-path/
total 0
lrwxrwxrwx 1 root root 12 Mar 12 19:54 platform-2040000.vpu-video-index0 -> ../../video0
lrwxrwxrwx 1 root root 12 Mar 12 19:54 platform-2040000.vpu-video-index1 -> ../../video1
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index0 -> ../../video2
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index1 -> ../../video3
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index2 -> ../../video4
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index3 -> ../../video5
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index4 -> ../../video6
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index5 -> ../../video7
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index6 -> ../../video8
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index7 -> ../../video9
lrwxrwxrwx 1 root root 13 Mar 12 19:54 platform-ci_hdrc.0-usb-0:1:1.0-video-index0 -> ../../video10

The problem is the "platform-capture-subsystem-video-index" entries.
These themselves change order.  For instance, I now have:

- entity 72: ipu1_csi0 capture (1 pad, 1 link)
             type Node subtype V4L flags 0
             device node name /dev/video6

which means it's platform-capture-subsystem-video-index4.  Before, it
was platform-capture-subsystem-video-index2.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 12, 2017 at 05:59:28PM -0300, Mauro Carvalho Chehab wrote:
> Yet, udev/systemd has some rules that provide an unique name for V4L
> devices at /lib/udev/rules.d/60-persistent-v4l.rules. Basically, it
> runs a small application (v4l_id) with creates a persistent symling
> using rules like this:
> 
> 	KERNEL=="video*", ENV{ID_SERIAL}=="?*", SYMLINK+="v4l/by-id/$env{ID_BUS}-$env{ID_SERIAL}-video-index$attr{index}"
> 
> Those names are stored at /dev/v4l/by-path.

This doesn't help:

$ ls -Al /dev/v4l/by-id/
total 0
lrwxrwxrwx 1 root root 13 Mar 12 19:54 usb-Sonix_Technology_Co.__Ltd._USB_2.0_Camera-video-index0 -> ../../video10
$ ls -Al /dev/v4l/by-path/
total 0
lrwxrwxrwx 1 root root 12 Mar 12 19:54 platform-2040000.vpu-video-index0 -> ../../video0
lrwxrwxrwx 1 root root 12 Mar 12 19:54 platform-2040000.vpu-video-index1 -> ../../video1
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index0 -> ../../video2
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index1 -> ../../video3
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index2 -> ../../video4
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index3 -> ../../video5
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index4 -> ../../video6
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index5 -> ../../video7
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index6 -> ../../video8
lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index7 -> ../../video9
lrwxrwxrwx 1 root root 13 Mar 12 19:54 platform-ci_hdrc.0-usb-0:1:1.0-video-index0 -> ../../video10

The problem is the "platform-capture-subsystem-video-index" entries.
These themselves change order.  For instance, I now have:

- entity 72: ipu1_csi0 capture (1 pad, 1 link)
             type Node subtype V4L flags 0
             device node name /dev/video6

which means it's platform-capture-subsystem-video-index4.  Before, it
was platform-capture-subsystem-video-index2.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Mauro Carvalho Chehab]

Em Sun, 12 Mar 2017 21:13:24 +0000
Russell King - ARM Linux <linux@armlinux.org.uk> escreveu:

> On Sun, Mar 12, 2017 at 05:59:28PM -0300, Mauro Carvalho Chehab wrote:
> > Yet, udev/systemd has some rules that provide an unique name for V4L
> > devices at /lib/udev/rules.d/60-persistent-v4l.rules. Basically, it
> > runs a small application (v4l_id) with creates a persistent symling
> > using rules like this:
> > 
> > 	KERNEL=="video*", ENV{ID_SERIAL}=="?*", SYMLINK+="v4l/by-id/$env{ID_BUS}-$env{ID_SERIAL}-video-index$attr{index}"
> > 
> > Those names are stored at /dev/v4l/by-path.  
> 
> This doesn't help:
> 
> $ ls -Al /dev/v4l/by-id/
> total 0
> lrwxrwxrwx 1 root root 13 Mar 12 19:54 usb-Sonix_Technology_Co.__Ltd._USB_2.0_Camera-video-index0 -> ../../video10
> $ ls -Al /dev/v4l/by-path/
> total 0
> lrwxrwxrwx 1 root root 12 Mar 12 19:54 platform-2040000.vpu-video-index0 -> ../../video0
> lrwxrwxrwx 1 root root 12 Mar 12 19:54 platform-2040000.vpu-video-index1 -> ../../video1
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index0 -> ../../video2
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index1 -> ../../video3
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index2 -> ../../video4
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index3 -> ../../video5
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index4 -> ../../video6
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index5 -> ../../video7
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index6 -> ../../video8
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index7 -> ../../video9
> lrwxrwxrwx 1 root root 13 Mar 12 19:54 platform-ci_hdrc.0-usb-0:1:1.0-video-index0 -> ../../video10
> 
> The problem is the "platform-capture-subsystem-video-index" entries.
> These themselves change order.  For instance, I now have:
> 
> - entity 72: ipu1_csi0 capture (1 pad, 1 link)
>              type Node subtype V4L flags 0
>              device node name /dev/video6
> 
> which means it's platform-capture-subsystem-video-index4.  Before, it
> was platform-capture-subsystem-video-index2.

That's a driver problem. v4l_id gets information to build the persistent
name from the result of VIDIOC_QUERYCAP.

In the case of Exynos gsc driver, for example, the information is here:

static int gsc_m2m_querycap(struct file *file, void *fh,
			   struct v4l2_capability *cap)
{
	struct gsc_ctx *ctx = fh_to_ctx(fh);
	struct gsc_dev *gsc = ctx->gsc_dev;

	strlcpy(cap->driver, GSC_MODULE_NAME, sizeof(cap->driver));
	strlcpy(cap->card, GSC_MODULE_NAME " gscaler", sizeof(cap->card));
	snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:%s",
		 dev_name(&gsc->pdev->dev));
	cap->device_caps = V4L2_CAP_STREAMING | V4L2_CAP_VIDEO_M2M_MPLANE |
		V4L2_CAP_VIDEO_CAPTURE_MPLANE |	V4L2_CAP_VIDEO_OUTPUT_MPLANE;

	cap->capabilities = cap->device_caps | V4L2_CAP_DEVICE_CAPS;
	return 0;
}

See that the bus_info there is filled with:

	snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:%s", dev_name(&gsc->pdev->dev));

>From the output you printed, it seems that the i.MX6 is just doing:
	snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:");
for some devices.

If you change the i.MX6 driver to do the same, you'll likely be able to
have unique names there too.

Regards,
Mauro

[PATCH v5 00/39] i.MX Media Driver

[Mauro Carvalho Chehab]

Em Sun, 12 Mar 2017 21:13:24 +0000
Russell King - ARM Linux <linux@armlinux.org.uk> escreveu:

> On Sun, Mar 12, 2017 at 05:59:28PM -0300, Mauro Carvalho Chehab wrote:
> > Yet, udev/systemd has some rules that provide an unique name for V4L
> > devices at /lib/udev/rules.d/60-persistent-v4l.rules. Basically, it
> > runs a small application (v4l_id) with creates a persistent symling
> > using rules like this:
> > 
> > 	KERNEL=="video*", ENV{ID_SERIAL}=="?*", SYMLINK+="v4l/by-id/$env{ID_BUS}-$env{ID_SERIAL}-video-index$attr{index}"
> > 
> > Those names are stored at /dev/v4l/by-path.  
> 
> This doesn't help:
> 
> $ ls -Al /dev/v4l/by-id/
> total 0
> lrwxrwxrwx 1 root root 13 Mar 12 19:54 usb-Sonix_Technology_Co.__Ltd._USB_2.0_Camera-video-index0 -> ../../video10
> $ ls -Al /dev/v4l/by-path/
> total 0
> lrwxrwxrwx 1 root root 12 Mar 12 19:54 platform-2040000.vpu-video-index0 -> ../../video0
> lrwxrwxrwx 1 root root 12 Mar 12 19:54 platform-2040000.vpu-video-index1 -> ../../video1
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index0 -> ../../video2
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index1 -> ../../video3
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index2 -> ../../video4
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index3 -> ../../video5
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index4 -> ../../video6
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index5 -> ../../video7
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index6 -> ../../video8
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index7 -> ../../video9
> lrwxrwxrwx 1 root root 13 Mar 12 19:54 platform-ci_hdrc.0-usb-0:1:1.0-video-index0 -> ../../video10
> 
> The problem is the "platform-capture-subsystem-video-index" entries.
> These themselves change order.  For instance, I now have:
> 
> - entity 72: ipu1_csi0 capture (1 pad, 1 link)
>              type Node subtype V4L flags 0
>              device node name /dev/video6
> 
> which means it's platform-capture-subsystem-video-index4.  Before, it
> was platform-capture-subsystem-video-index2.

That's a driver problem. v4l_id gets information to build the persistent
name from the result of VIDIOC_QUERYCAP.

In the case of Exynos gsc driver, for example, the information is here:

static int gsc_m2m_querycap(struct file *file, void *fh,
			   struct v4l2_capability *cap)
{
	struct gsc_ctx *ctx = fh_to_ctx(fh);
	struct gsc_dev *gsc = ctx->gsc_dev;

	strlcpy(cap->driver, GSC_MODULE_NAME, sizeof(cap->driver));
	strlcpy(cap->card, GSC_MODULE_NAME " gscaler", sizeof(cap->card));
	snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:%s",
		 dev_name(&gsc->pdev->dev));
	cap->device_caps = V4L2_CAP_STREAMING | V4L2_CAP_VIDEO_M2M_MPLANE |
		V4L2_CAP_VIDEO_CAPTURE_MPLANE |	V4L2_CAP_VIDEO_OUTPUT_MPLANE;

	cap->capabilities = cap->device_caps | V4L2_CAP_DEVICE_CAPS;
	return 0;
}

See that the bus_info there is filled with:

	snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:%s", dev_name(&gsc->pdev->dev));

>From the output you printed, it seems that the i.MX6 is just doing:
	snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:");
for some devices.

If you change the i.MX6 driver to do the same, you'll likely be able to
have unique names there too.

Regards,
Mauro

Re: [PATCH v5 00/39] i.MX Media Driver

[Mauro Carvalho Chehab]

Em Sun, 12 Mar 2017 21:13:24 +0000
Russell King - ARM Linux <linux-I+IVW8TIWO2tmTQ+vhA3Yw@public.gmane.org> escreveu:

> On Sun, Mar 12, 2017 at 05:59:28PM -0300, Mauro Carvalho Chehab wrote:
> > Yet, udev/systemd has some rules that provide an unique name for V4L
> > devices at /lib/udev/rules.d/60-persistent-v4l.rules. Basically, it
> > runs a small application (v4l_id) with creates a persistent symling
> > using rules like this:
> > 
> > 	KERNEL=="video*", ENV{ID_SERIAL}=="?*", SYMLINK+="v4l/by-id/$env{ID_BUS}-$env{ID_SERIAL}-video-index$attr{index}"
> > 
> > Those names are stored at /dev/v4l/by-path.  
> 
> This doesn't help:
> 
> $ ls -Al /dev/v4l/by-id/
> total 0
> lrwxrwxrwx 1 root root 13 Mar 12 19:54 usb-Sonix_Technology_Co.__Ltd._USB_2.0_Camera-video-index0 -> ../../video10
> $ ls -Al /dev/v4l/by-path/
> total 0
> lrwxrwxrwx 1 root root 12 Mar 12 19:54 platform-2040000.vpu-video-index0 -> ../../video0
> lrwxrwxrwx 1 root root 12 Mar 12 19:54 platform-2040000.vpu-video-index1 -> ../../video1
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index0 -> ../../video2
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index1 -> ../../video3
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index2 -> ../../video4
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index3 -> ../../video5
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index4 -> ../../video6
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index5 -> ../../video7
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index6 -> ../../video8
> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index7 -> ../../video9
> lrwxrwxrwx 1 root root 13 Mar 12 19:54 platform-ci_hdrc.0-usb-0:1:1.0-video-index0 -> ../../video10
> 
> The problem is the "platform-capture-subsystem-video-index" entries.
> These themselves change order.  For instance, I now have:
> 
> - entity 72: ipu1_csi0 capture (1 pad, 1 link)
>              type Node subtype V4L flags 0
>              device node name /dev/video6
> 
> which means it's platform-capture-subsystem-video-index4.  Before, it
> was platform-capture-subsystem-video-index2.

That's a driver problem. v4l_id gets information to build the persistent
name from the result of VIDIOC_QUERYCAP.

In the case of Exynos gsc driver, for example, the information is here:

static int gsc_m2m_querycap(struct file *file, void *fh,
			   struct v4l2_capability *cap)
{
	struct gsc_ctx *ctx = fh_to_ctx(fh);
	struct gsc_dev *gsc = ctx->gsc_dev;

	strlcpy(cap->driver, GSC_MODULE_NAME, sizeof(cap->driver));
	strlcpy(cap->card, GSC_MODULE_NAME " gscaler", sizeof(cap->card));
	snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:%s",
		 dev_name(&gsc->pdev->dev));
	cap->device_caps = V4L2_CAP_STREAMING | V4L2_CAP_VIDEO_M2M_MPLANE |
		V4L2_CAP_VIDEO_CAPTURE_MPLANE |	V4L2_CAP_VIDEO_OUTPUT_MPLANE;

	cap->capabilities = cap->device_caps | V4L2_CAP_DEVICE_CAPS;
	return 0;
}

See that the bus_info there is filled with:

	snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:%s", dev_name(&gsc->pdev->dev));

>From the output you printed, it seems that the i.MX6 is just doing:
	snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:");
for some devices.

If you change the i.MX6 driver to do the same, you'll likely be able to
have unique names there too.

Regards,
Mauro
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 03:10 PM, Mauro Carvalho Chehab wrote:
> Em Sun, 12 Mar 2017 21:13:24 +0000
> Russell King - ARM Linux <linux@armlinux.org.uk> escreveu:
>
>> On Sun, Mar 12, 2017 at 05:59:28PM -0300, Mauro Carvalho Chehab wrote:
>>> Yet, udev/systemd has some rules that provide an unique name for V4L
>>> devices at /lib/udev/rules.d/60-persistent-v4l.rules. Basically, it
>>> runs a small application (v4l_id) with creates a persistent symling
>>> using rules like this:
>>>
>>> 	KERNEL=="video*", ENV{ID_SERIAL}=="?*", SYMLINK+="v4l/by-id/$env{ID_BUS}-$env{ID_SERIAL}-video-index$attr{index}"
>>>
>>> Those names are stored at /dev/v4l/by-path.
>> This doesn't help:
>>
>> $ ls -Al /dev/v4l/by-id/
>> total 0
>> lrwxrwxrwx 1 root root 13 Mar 12 19:54 usb-Sonix_Technology_Co.__Ltd._USB_2.0_Camera-video-index0 -> ../../video10
>> $ ls -Al /dev/v4l/by-path/
>> total 0
>> lrwxrwxrwx 1 root root 12 Mar 12 19:54 platform-2040000.vpu-video-index0 -> ../../video0
>> lrwxrwxrwx 1 root root 12 Mar 12 19:54 platform-2040000.vpu-video-index1 -> ../../video1
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index0 -> ../../video2
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index1 -> ../../video3
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index2 -> ../../video4
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index3 -> ../../video5
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index4 -> ../../video6
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index5 -> ../../video7
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index6 -> ../../video8
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index7 -> ../../video9
>> lrwxrwxrwx 1 root root 13 Mar 12 19:54 platform-ci_hdrc.0-usb-0:1:1.0-video-index0 -> ../../video10
>>
>> The problem is the "platform-capture-subsystem-video-index" entries.
>> These themselves change order.  For instance, I now have:
>>
>> - entity 72: ipu1_csi0 capture (1 pad, 1 link)
>>               type Node subtype V4L flags 0
>>               device node name /dev/video6
>>
>> which means it's platform-capture-subsystem-video-index4.  Before, it
>> was platform-capture-subsystem-video-index2.
> That's a driver problem. v4l_id gets information to build the persistent
> name from the result of VIDIOC_QUERYCAP.
>
> In the case of Exynos gsc driver, for example, the information is here:
>
> static int gsc_m2m_querycap(struct file *file, void *fh,
> 			   struct v4l2_capability *cap)
> {
> 	struct gsc_ctx *ctx = fh_to_ctx(fh);
> 	struct gsc_dev *gsc = ctx->gsc_dev;
>
> 	strlcpy(cap->driver, GSC_MODULE_NAME, sizeof(cap->driver));
> 	strlcpy(cap->card, GSC_MODULE_NAME " gscaler", sizeof(cap->card));
> 	snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:%s",
> 		 dev_name(&gsc->pdev->dev));
> 	cap->device_caps = V4L2_CAP_STREAMING | V4L2_CAP_VIDEO_M2M_MPLANE |
> 		V4L2_CAP_VIDEO_CAPTURE_MPLANE |	V4L2_CAP_VIDEO_OUTPUT_MPLANE;
>
> 	cap->capabilities = cap->device_caps | V4L2_CAP_DEVICE_CAPS;
> 	return 0;
> }
>
> See that the bus_info there is filled with:
>
> 	snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:%s", dev_name(&gsc->pdev->dev));
>
>  From the output you printed, it seems that the i.MX6 is just doing:
> 	snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:");
> for some devices.

imx6 is setting bus_info string on all capture devices as:

snprintf(cap->bus_info, sizeof(cap->bus_info),
                  "platform:%s", dev_name(priv->dev));

dev_name(priv->dev) is the device name of the attached subdev.
So the bus_info string, at least for attached CSI subdevs, should
be "platform:imx-ipuv3-csi".

Maybe there is something else missing, I haven't had a chance to
look at this yet.

Steve


>
> If you change the i.MX6 driver to do the same, you'll likely be able to
> have unique names there too.
>
> Regards,
> Mauro

[PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 03:10 PM, Mauro Carvalho Chehab wrote:
> Em Sun, 12 Mar 2017 21:13:24 +0000
> Russell King - ARM Linux <linux@armlinux.org.uk> escreveu:
>
>> On Sun, Mar 12, 2017 at 05:59:28PM -0300, Mauro Carvalho Chehab wrote:
>>> Yet, udev/systemd has some rules that provide an unique name for V4L
>>> devices at /lib/udev/rules.d/60-persistent-v4l.rules. Basically, it
>>> runs a small application (v4l_id) with creates a persistent symling
>>> using rules like this:
>>>
>>> 	KERNEL=="video*", ENV{ID_SERIAL}=="?*", SYMLINK+="v4l/by-id/$env{ID_BUS}-$env{ID_SERIAL}-video-index$attr{index}"
>>>
>>> Those names are stored at /dev/v4l/by-path.
>> This doesn't help:
>>
>> $ ls -Al /dev/v4l/by-id/
>> total 0
>> lrwxrwxrwx 1 root root 13 Mar 12 19:54 usb-Sonix_Technology_Co.__Ltd._USB_2.0_Camera-video-index0 -> ../../video10
>> $ ls -Al /dev/v4l/by-path/
>> total 0
>> lrwxrwxrwx 1 root root 12 Mar 12 19:54 platform-2040000.vpu-video-index0 -> ../../video0
>> lrwxrwxrwx 1 root root 12 Mar 12 19:54 platform-2040000.vpu-video-index1 -> ../../video1
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index0 -> ../../video2
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index1 -> ../../video3
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index2 -> ../../video4
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index3 -> ../../video5
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index4 -> ../../video6
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index5 -> ../../video7
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index6 -> ../../video8
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index7 -> ../../video9
>> lrwxrwxrwx 1 root root 13 Mar 12 19:54 platform-ci_hdrc.0-usb-0:1:1.0-video-index0 -> ../../video10
>>
>> The problem is the "platform-capture-subsystem-video-index" entries.
>> These themselves change order.  For instance, I now have:
>>
>> - entity 72: ipu1_csi0 capture (1 pad, 1 link)
>>               type Node subtype V4L flags 0
>>               device node name /dev/video6
>>
>> which means it's platform-capture-subsystem-video-index4.  Before, it
>> was platform-capture-subsystem-video-index2.
> That's a driver problem. v4l_id gets information to build the persistent
> name from the result of VIDIOC_QUERYCAP.
>
> In the case of Exynos gsc driver, for example, the information is here:
>
> static int gsc_m2m_querycap(struct file *file, void *fh,
> 			   struct v4l2_capability *cap)
> {
> 	struct gsc_ctx *ctx = fh_to_ctx(fh);
> 	struct gsc_dev *gsc = ctx->gsc_dev;
>
> 	strlcpy(cap->driver, GSC_MODULE_NAME, sizeof(cap->driver));
> 	strlcpy(cap->card, GSC_MODULE_NAME " gscaler", sizeof(cap->card));
> 	snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:%s",
> 		 dev_name(&gsc->pdev->dev));
> 	cap->device_caps = V4L2_CAP_STREAMING | V4L2_CAP_VIDEO_M2M_MPLANE |
> 		V4L2_CAP_VIDEO_CAPTURE_MPLANE |	V4L2_CAP_VIDEO_OUTPUT_MPLANE;
>
> 	cap->capabilities = cap->device_caps | V4L2_CAP_DEVICE_CAPS;
> 	return 0;
> }
>
> See that the bus_info there is filled with:
>
> 	snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:%s", dev_name(&gsc->pdev->dev));
>
>  From the output you printed, it seems that the i.MX6 is just doing:
> 	snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:");
> for some devices.

imx6 is setting bus_info string on all capture devices as:

snprintf(cap->bus_info, sizeof(cap->bus_info),
                  "platform:%s", dev_name(priv->dev));

dev_name(priv->dev) is the device name of the attached subdev.
So the bus_info string, at least for attached CSI subdevs, should
be "platform:imx-ipuv3-csi".

Maybe there is something else missing, I haven't had a chance to
look at this yet.

Steve


>
> If you change the i.MX6 driver to do the same, you'll likely be able to
> have unique names there too.
>
> Regards,
> Mauro

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/12/2017 03:10 PM, Mauro Carvalho Chehab wrote:
> Em Sun, 12 Mar 2017 21:13:24 +0000
> Russell King - ARM Linux <linux@armlinux.org.uk> escreveu:
>
>> On Sun, Mar 12, 2017 at 05:59:28PM -0300, Mauro Carvalho Chehab wrote:
>>> Yet, udev/systemd has some rules that provide an unique name for V4L
>>> devices at /lib/udev/rules.d/60-persistent-v4l.rules. Basically, it
>>> runs a small application (v4l_id) with creates a persistent symling
>>> using rules like this:
>>>
>>> 	KERNEL=="video*", ENV{ID_SERIAL}=="?*", SYMLINK+="v4l/by-id/$env{ID_BUS}-$env{ID_SERIAL}-video-index$attr{index}"
>>>
>>> Those names are stored at /dev/v4l/by-path.
>> This doesn't help:
>>
>> $ ls -Al /dev/v4l/by-id/
>> total 0
>> lrwxrwxrwx 1 root root 13 Mar 12 19:54 usb-Sonix_Technology_Co.__Ltd._USB_2.0_Camera-video-index0 -> ../../video10
>> $ ls -Al /dev/v4l/by-path/
>> total 0
>> lrwxrwxrwx 1 root root 12 Mar 12 19:54 platform-2040000.vpu-video-index0 -> ../../video0
>> lrwxrwxrwx 1 root root 12 Mar 12 19:54 platform-2040000.vpu-video-index1 -> ../../video1
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index0 -> ../../video2
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index1 -> ../../video3
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index2 -> ../../video4
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index3 -> ../../video5
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index4 -> ../../video6
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index5 -> ../../video7
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index6 -> ../../video8
>> lrwxrwxrwx 1 root root 12 Mar 12 20:53 platform-capture-subsystem-video-index7 -> ../../video9
>> lrwxrwxrwx 1 root root 13 Mar 12 19:54 platform-ci_hdrc.0-usb-0:1:1.0-video-index0 -> ../../video10
>>
>> The problem is the "platform-capture-subsystem-video-index" entries.
>> These themselves change order.  For instance, I now have:
>>
>> - entity 72: ipu1_csi0 capture (1 pad, 1 link)
>>               type Node subtype V4L flags 0
>>               device node name /dev/video6
>>
>> which means it's platform-capture-subsystem-video-index4.  Before, it
>> was platform-capture-subsystem-video-index2.
> That's a driver problem. v4l_id gets information to build the persistent
> name from the result of VIDIOC_QUERYCAP.
>
> In the case of Exynos gsc driver, for example, the information is here:
>
> static int gsc_m2m_querycap(struct file *file, void *fh,
> 			   struct v4l2_capability *cap)
> {
> 	struct gsc_ctx *ctx = fh_to_ctx(fh);
> 	struct gsc_dev *gsc = ctx->gsc_dev;
>
> 	strlcpy(cap->driver, GSC_MODULE_NAME, sizeof(cap->driver));
> 	strlcpy(cap->card, GSC_MODULE_NAME " gscaler", sizeof(cap->card));
> 	snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:%s",
> 		 dev_name(&gsc->pdev->dev));
> 	cap->device_caps = V4L2_CAP_STREAMING | V4L2_CAP_VIDEO_M2M_MPLANE |
> 		V4L2_CAP_VIDEO_CAPTURE_MPLANE |	V4L2_CAP_VIDEO_OUTPUT_MPLANE;
>
> 	cap->capabilities = cap->device_caps | V4L2_CAP_DEVICE_CAPS;
> 	return 0;
> }
>
> See that the bus_info there is filled with:
>
> 	snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:%s", dev_name(&gsc->pdev->dev));
>
>  From the output you printed, it seems that the i.MX6 is just doing:
> 	snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:");
> for some devices.

imx6 is setting bus_info string on all capture devices as:

snprintf(cap->bus_info, sizeof(cap->bus_info),
                  "platform:%s", dev_name(priv->dev));

dev_name(priv->dev) is the device name of the attached subdev.
So the bus_info string, at least for attached CSI subdevs, should
be "platform:imx-ipuv3-csi".

Maybe there is something else missing, I haven't had a chance to
look at this yet.

Steve


>
> If you change the i.MX6 driver to do the same, you'll likely be able to
> have unique names there too.
>
> Regards,
> Mauro

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

Hi Steve,

I've just been trying to get gstreamer to capture and h264 encode
video from my camera at various frame rates, and what I've discovered
does not look good.

1) when setting frame rates, media-ctl _always_ calls
   VIDIOC_SUBDEV_S_FRAME_INTERVAL with pad=0.

2) media-ctl never retrieves the frame interval information, so there's
   no way to read it back with standard tools, and no indication that
   this is going on...

3) gstreamer v4l2src is getting upset, because it can't enumerate the
   frame sizes (VIDIOC_ENUM_FRAMESIZES fails), which causes it to
   fallback to using the "tvnorms" to decide about frame rates.  This
   makes it impossible to use frame rates higher than 30000/1001, and
   causes the pipeline validation to fail.

0:00:01.937465845 20954  0x15ffe90 DEBUG                   v4l2 gstv4l2object.c:2474:gst_v4l2_object_probe_caps_for_format:<v4l2src0> Enumerating frame sizes for RGGB
0:00:01.937588518 20954  0x15ffe90 DEBUG                   v4l2 gstv4l2object.c:2601:gst_v4l2_object_probe_caps_for_format:<v4l2src0> Failed to enumerate frame sizes for pixelformat RGGB (Inappropriate ioctl for device)
0:00:01.937879535 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2708:gst_v4l2_object_get_nearest_size:<v4l2src0> getting nearest size to 1x1 with format RGGB
0:00:01.937990874 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2724:gst_v4l2_object_get_nearest_size:<v4l2src0> got nearest size 816x616
0:00:01.938250889 20954  0x15ffe90 ERROR                   v4l2 gstv4l2object.c:1873:gst_v4l2_object_get_interlace_mode: Driver bug detected - check driver with v4l2-compliance from http://git.linuxtv.org/v4l-utils.git
0:00:01.938326893 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2708:gst_v4l2_object_get_nearest_size:<v4l2src0> getting nearest size to 32768x32768 with format RGGB
0:00:01.938431566 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2724:gst_v4l2_object_get_nearest_size:<v4l2src0> got nearest size 816x616
0:00:01.939776641 20954  0x15ffe90 ERROR                   v4l2 gstv4l2object.c:1873:gst_v4l2_object_get_interlace_mode: Driver bug detected - check driver with v4l2-compliance from http://git.linuxtv.org/v4l-utils.git
0:00:01.940110660 20954  0x15ffe90 DEBUG                   v4l2 gstv4l2object.c:1955:gst_v4l2_object_get_colorspace: Unknown enum v4l2_colorspace 0

   This triggers the "/* Since we can't get framerate directly, try to
   use the current norm */" code in v4l2object.c, which causes it to
   select one of the 30000/1001 norms:

0:00:01.955927879 20954  0x15ffe90 INFO                    v4l2 gstv4l2object.c:3811:gst_v4l2_object_get_caps:<v4l2src0> probed caps: video/x-bayer, format=(string)rggb, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)I420, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)YV12, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)BGR, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)RGB, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1

   despite the media pipeline actually being configured for 60fps.

   Forcing it by adjusting the pipeline only results in gstreamer
   failing, because it believes that v4l2 is unable to operate at
   60fps.

   Also note the complaints from v4l2src about the non-compliance...

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

Hi Steve,

I've just been trying to get gstreamer to capture and h264 encode
video from my camera at various frame rates, and what I've discovered
does not look good.

1) when setting frame rates, media-ctl _always_ calls
   VIDIOC_SUBDEV_S_FRAME_INTERVAL with pad=0.

2) media-ctl never retrieves the frame interval information, so there's
   no way to read it back with standard tools, and no indication that
   this is going on...

3) gstreamer v4l2src is getting upset, because it can't enumerate the
   frame sizes (VIDIOC_ENUM_FRAMESIZES fails), which causes it to
   fallback to using the "tvnorms" to decide about frame rates.  This
   makes it impossible to use frame rates higher than 30000/1001, and
   causes the pipeline validation to fail.

0:00:01.937465845 20954  0x15ffe90 DEBUG                   v4l2 gstv4l2object.c:2474:gst_v4l2_object_probe_caps_for_format:<v4l2src0> Enumerating frame sizes for RGGB
0:00:01.937588518 20954  0x15ffe90 DEBUG                   v4l2 gstv4l2object.c:2601:gst_v4l2_object_probe_caps_for_format:<v4l2src0> Failed to enumerate frame sizes for pixelformat RGGB (Inappropriate ioctl for device)
0:00:01.937879535 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2708:gst_v4l2_object_get_nearest_size:<v4l2src0> getting nearest size to 1x1 with format RGGB
0:00:01.937990874 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2724:gst_v4l2_object_get_nearest_size:<v4l2src0> got nearest size 816x616
0:00:01.938250889 20954  0x15ffe90 ERROR                   v4l2 gstv4l2object.c:1873:gst_v4l2_object_get_interlace_mode: Driver bug detected - check driver with v4l2-compliance from http://git.linuxtv.org/v4l-utils.git
0:00:01.938326893 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2708:gst_v4l2_object_get_nearest_size:<v4l2src0> getting nearest size to 32768x32768 with format RGGB
0:00:01.938431566 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2724:gst_v4l2_object_get_nearest_size:<v4l2src0> got nearest size 816x616
0:00:01.939776641 20954  0x15ffe90 ERROR                   v4l2 gstv4l2object.c:1873:gst_v4l2_object_get_interlace_mode: Driver bug detected - check driver with v4l2-compliance from http://git.linuxtv.org/v4l-utils.git
0:00:01.940110660 20954  0x15ffe90 DEBUG                   v4l2 gstv4l2object.c:1955:gst_v4l2_object_get_colorspace: Unknown enum v4l2_colorspace 0

   This triggers the "/* Since we can't get framerate directly, try to
   use the current norm */" code in v4l2object.c, which causes it to
   select one of the 30000/1001 norms:

0:00:01.955927879 20954  0x15ffe90 INFO                    v4l2 gstv4l2object.c:3811:gst_v4l2_object_get_caps:<v4l2src0> probed caps: video/x-bayer, format=(string)rggb, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)I420, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)YV12, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)BGR, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)RGB, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1

   despite the media pipeline actually being configured for 60fps.

   Forcing it by adjusting the pipeline only results in gstreamer
   failing, because it believes that v4l2 is unable to operate at
   60fps.

   Also note the complaints from v4l2src about the non-compliance...

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

Hi Steve,

I've just been trying to get gstreamer to capture and h264 encode
video from my camera at various frame rates, and what I've discovered
does not look good.

1) when setting frame rates, media-ctl _always_ calls
   VIDIOC_SUBDEV_S_FRAME_INTERVAL with pad=0.

2) media-ctl never retrieves the frame interval information, so there's
   no way to read it back with standard tools, and no indication that
   this is going on...

3) gstreamer v4l2src is getting upset, because it can't enumerate the
   frame sizes (VIDIOC_ENUM_FRAMESIZES fails), which causes it to
   fallback to using the "tvnorms" to decide about frame rates.  This
   makes it impossible to use frame rates higher than 30000/1001, and
   causes the pipeline validation to fail.

0:00:01.937465845 20954  0x15ffe90 DEBUG                   v4l2 gstv4l2object.c:2474:gst_v4l2_object_probe_caps_for_format:<v4l2src0> Enumerating frame sizes for RGGB
0:00:01.937588518 20954  0x15ffe90 DEBUG                   v4l2 gstv4l2object.c:2601:gst_v4l2_object_probe_caps_for_format:<v4l2src0> Failed to enumerate frame sizes for pixelformat RGGB (Inappropriate ioctl for device)
0:00:01.937879535 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2708:gst_v4l2_object_get_nearest_size:<v4l2src0> getting nearest size to 1x1 with format RGGB
0:00:01.937990874 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2724:gst_v4l2_object_get_nearest_size:<v4l2src0> got nearest size 816x616
0:00:01.938250889 20954  0x15ffe90 ERROR                   v4l2 gstv4l2object.c:1873:gst_v4l2_object_get_interlace_mode: Driver bug detected - check driver with v4l2-compliance from http://git.linuxtv.org/v4l-utils.git
0:00:01.938326893 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2708:gst_v4l2_object_get_nearest_size:<v4l2src0> getting nearest size to 32768x32768 with format RGGB
0:00:01.938431566 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2724:gst_v4l2_object_get_nearest_size:<v4l2src0> got nearest size 816x616
0:00:01.939776641 20954  0x15ffe90 ERROR                   v4l2 gstv4l2object.c:1873:gst_v4l2_object_get_interlace_mode: Driver bug detected - check driver with v4l2-compliance from http://git.linuxtv.org/v4l-utils.git
0:00:01.940110660 20954  0x15ffe90 DEBUG                   v4l2 gstv4l2object.c:1955:gst_v4l2_object_get_colorspace: Unknown enum v4l2_colorspace 0

   This triggers the "/* Since we can't get framerate directly, try to
   use the current norm */" code in v4l2object.c, which causes it to
   select one of the 30000/1001 norms:

0:00:01.955927879 20954  0x15ffe90 INFO                    v4l2 gstv4l2object.c:3811:gst_v4l2_object_get_caps:<v4l2src0> probed caps: video/x-bayer, format=(string)rggb, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)I420, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)YV12, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)BGR, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(stri
 ng)RGB, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1

   despite the media pipeline actually being configured for 60fps.

   Forcing it by adjusting the pipeline only results in gstreamer
   failing, because it believes that v4l2 is unable to operate at
   60fps.

   Also note the complaints from v4l2src about the non-compliance...

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

[-- Attachment #1: Type: text/plain, Size: 4828 bytes --]



On 03/18/2017 12:22 PM, Russell King - ARM Linux wrote:
> Hi Steve,
>
> I've just been trying to get gstreamer to capture and h264 encode
> video from my camera at various frame rates, and what I've discovered
> does not look good.
>
> 1) when setting frame rates, media-ctl _always_ calls
>     VIDIOC_SUBDEV_S_FRAME_INTERVAL with pad=0.
>
> 2) media-ctl never retrieves the frame interval information, so there's
>     no way to read it back with standard tools, and no indication that
>     this is going on...

I think Philipp Zabel submitted a patch which addresses these
in media-ctl. Check with him.

>
> 3) gstreamer v4l2src is getting upset, because it can't enumerate the
>     frame sizes (VIDIOC_ENUM_FRAMESIZES fails),

Right, imx-media-capture.c (the "standard" v4l2 user interface module)
is not implementing VIDIOC_ENUM_FRAMESIZES. It should, but it can only
return the single frame size that the pipeline has configured (the mbus
format of the attached source pad).

>   which causes it to
>     fallback to using the "tvnorms" to decide about frame rates.  This
>     makes it impossible to use frame rates higher than 30000/1001, and
>     causes the pipeline validation to fail.

In v5 I added validation of frame intervals between pads,
but due to negative feedback I've pulled that. So next
version will not attempt to validate frame intervals between
source->sink pads.

Can you share your gstreamer pipeline? For now, until
VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
does not attempt to specify a frame rate. I use the attached
script for testing, which works for me.



>
> 0:00:01.937465845 20954  0x15ffe90 DEBUG                   v4l2 gstv4l2object.c:2474:gst_v4l2_object_probe_caps_for_format:<v4l2src0> Enumerating frame sizes for RGGB
> 0:00:01.937588518 20954  0x15ffe90 DEBUG                   v4l2 gstv4l2object.c:2601:gst_v4l2_object_probe_caps_for_format:<v4l2src0> Failed to enumerate frame sizes for pixelformat RGGB (Inappropriate ioctl for device)
> 0:00:01.937879535 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2708:gst_v4l2_object_get_nearest_size:<v4l2src0> getting nearest size to 1x1 with format RGGB
> 0:00:01.937990874 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2724:gst_v4l2_object_get_nearest_size:<v4l2src0> got nearest size 816x616
> 0:00:01.938250889 20954  0x15ffe90 ERROR                   v4l2 gstv4l2object.c:1873:gst_v4l2_object_get_interlace_mode: Driver bug detected - check driver with v4l2-compliance from http://git.linuxtv.org/v4l-utils.git
> 0:00:01.938326893 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2708:gst_v4l2_object_get_nearest_size:<v4l2src0> getting nearest size to 32768x32768 with format RGGB
> 0:00:01.938431566 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2724:gst_v4l2_object_get_nearest_size:<v4l2src0> got nearest size 816x616
> 0:00:01.939776641 20954  0x15ffe90 ERROR                   v4l2 gstv4l2object.c:1873:gst_v4l2_object_get_interlace_mode: Driver bug detected - check driver with v4l2-compliance from http://git.linuxtv.org/v4l-utils.git
> 0:00:01.940110660 20954  0x15ffe90 DEBUG                   v4l2 gstv4l2object.c:1955:gst_v4l2_object_get_colorspace: Unknown enum v4l2_colorspace 0
>
>     This triggers the "/* Since we can't get framerate directly, try to
>     use the current norm */" code in v4l2object.c, which causes it to
>     select one of the 30000/1001 norms:
>
> 0:00:01.955927879 20954  0x15ffe90 INFO                    v4l2 gstv4l2object.c:3811:gst_v4l2_object_get_caps:<v4l2src0> probed caps: video/x-bayer, format=(string)rggb, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)I420, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)YV12, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)BGR, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)RGB, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1
>
>     despite the media pipeline actually being configured for 60fps.
>
>     Forcing it by adjusting the pipeline only results in gstreamer
>     failing, because it believes that v4l2 is unable to operate at
>     60fps.
>
>     Also note the complaints from v4l2src about the non-compliance...

Thanks, I've fixed most of v4l2-compliance issues, but this is not
done yet. Is that something you can help with?

Steve


[-- Attachment #2: udpstream.sh --]
[-- Type: application/x-shellscript, Size: 381 bytes --]

[PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/18/2017 12:22 PM, Russell King - ARM Linux wrote:
> Hi Steve,
>
> I've just been trying to get gstreamer to capture and h264 encode
> video from my camera at various frame rates, and what I've discovered
> does not look good.
>
> 1) when setting frame rates, media-ctl _always_ calls
>     VIDIOC_SUBDEV_S_FRAME_INTERVAL with pad=0.
>
> 2) media-ctl never retrieves the frame interval information, so there's
>     no way to read it back with standard tools, and no indication that
>     this is going on...

I think Philipp Zabel submitted a patch which addresses these
in media-ctl. Check with him.

>
> 3) gstreamer v4l2src is getting upset, because it can't enumerate the
>     frame sizes (VIDIOC_ENUM_FRAMESIZES fails),

Right, imx-media-capture.c (the "standard" v4l2 user interface module)
is not implementing VIDIOC_ENUM_FRAMESIZES. It should, but it can only
return the single frame size that the pipeline has configured (the mbus
format of the attached source pad).

>   which causes it to
>     fallback to using the "tvnorms" to decide about frame rates.  This
>     makes it impossible to use frame rates higher than 30000/1001, and
>     causes the pipeline validation to fail.

In v5 I added validation of frame intervals between pads,
but due to negative feedback I've pulled that. So next
version will not attempt to validate frame intervals between
source->sink pads.

Can you share your gstreamer pipeline? For now, until
VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
does not attempt to specify a frame rate. I use the attached
script for testing, which works for me.



>
> 0:00:01.937465845 20954  0x15ffe90 DEBUG                   v4l2 gstv4l2object.c:2474:gst_v4l2_object_probe_caps_for_format:<v4l2src0> Enumerating frame sizes for RGGB
> 0:00:01.937588518 20954  0x15ffe90 DEBUG                   v4l2 gstv4l2object.c:2601:gst_v4l2_object_probe_caps_for_format:<v4l2src0> Failed to enumerate frame sizes for pixelformat RGGB (Inappropriate ioctl for device)
> 0:00:01.937879535 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2708:gst_v4l2_object_get_nearest_size:<v4l2src0> getting nearest size to 1x1 with format RGGB
> 0:00:01.937990874 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2724:gst_v4l2_object_get_nearest_size:<v4l2src0> got nearest size 816x616
> 0:00:01.938250889 20954  0x15ffe90 ERROR                   v4l2 gstv4l2object.c:1873:gst_v4l2_object_get_interlace_mode: Driver bug detected - check driver with v4l2-compliance from http://git.linuxtv.org/v4l-utils.git
> 0:00:01.938326893 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2708:gst_v4l2_object_get_nearest_size:<v4l2src0> getting nearest size to 32768x32768 with format RGGB
> 0:00:01.938431566 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2724:gst_v4l2_object_get_nearest_size:<v4l2src0> got nearest size 816x616
> 0:00:01.939776641 20954  0x15ffe90 ERROR                   v4l2 gstv4l2object.c:1873:gst_v4l2_object_get_interlace_mode: Driver bug detected - check driver with v4l2-compliance from http://git.linuxtv.org/v4l-utils.git
> 0:00:01.940110660 20954  0x15ffe90 DEBUG                   v4l2 gstv4l2object.c:1955:gst_v4l2_object_get_colorspace: Unknown enum v4l2_colorspace 0
>
>     This triggers the "/* Since we can't get framerate directly, try to
>     use the current norm */" code in v4l2object.c, which causes it to
>     select one of the 30000/1001 norms:
>
> 0:00:01.955927879 20954  0x15ffe90 INFO                    v4l2 gstv4l2object.c:3811:gst_v4l2_object_get_caps:<v4l2src0> probed caps: video/x-bayer, format=(string)rggb, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)I420, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)YV12, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)BGR, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)RGB, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1
>
>     despite the media pipeline actually being configured for 60fps.
>
>     Forcing it by adjusting the pipeline only results in gstreamer
>     failing, because it believes that v4l2 is unable to operate at
>     60fps.
>
>     Also note the complaints from v4l2src about the non-compliance...

Thanks, I've fixed most of v4l2-compliance issues, but this is not
done yet. Is that something you can help with?

Steve

-------------- next part --------------
A non-text attachment was scrubbed...
Name: udpstream.sh
Type: application/x-shellscript
Size: 381 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170318/35942579/attachment.bin>

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

[-- Attachment #1: Type: text/plain, Size: 4830 bytes --]



On 03/18/2017 12:22 PM, Russell King - ARM Linux wrote:
> Hi Steve,
>
> I've just been trying to get gstreamer to capture and h264 encode
> video from my camera at various frame rates, and what I've discovered
> does not look good.
>
> 1) when setting frame rates, media-ctl _always_ calls
>     VIDIOC_SUBDEV_S_FRAME_INTERVAL with pad=0.
>
> 2) media-ctl never retrieves the frame interval information, so there's
>     no way to read it back with standard tools, and no indication that
>     this is going on...

I think Philipp Zabel submitted a patch which addresses these
in media-ctl. Check with him.

>
> 3) gstreamer v4l2src is getting upset, because it can't enumerate the
>     frame sizes (VIDIOC_ENUM_FRAMESIZES fails),

Right, imx-media-capture.c (the "standard" v4l2 user interface module)
is not implementing VIDIOC_ENUM_FRAMESIZES. It should, but it can only
return the single frame size that the pipeline has configured (the mbus
format of the attached source pad).

>   which causes it to
>     fallback to using the "tvnorms" to decide about frame rates.  This
>     makes it impossible to use frame rates higher than 30000/1001, and
>     causes the pipeline validation to fail.

In v5 I added validation of frame intervals between pads,
but due to negative feedback I've pulled that. So next
version will not attempt to validate frame intervals between
source->sink pads.

Can you share your gstreamer pipeline? For now, until
VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
does not attempt to specify a frame rate. I use the attached
script for testing, which works for me.



>
> 0:00:01.937465845 20954  0x15ffe90 DEBUG                   v4l2 gstv4l2object.c:2474:gst_v4l2_object_probe_caps_for_format:<v4l2src0> Enumerating frame sizes for RGGB
> 0:00:01.937588518 20954  0x15ffe90 DEBUG                   v4l2 gstv4l2object.c:2601:gst_v4l2_object_probe_caps_for_format:<v4l2src0> Failed to enumerate frame sizes for pixelformat RGGB (Inappropriate ioctl for device)
> 0:00:01.937879535 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2708:gst_v4l2_object_get_nearest_size:<v4l2src0> getting nearest size to 1x1 with format RGGB
> 0:00:01.937990874 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2724:gst_v4l2_object_get_nearest_size:<v4l2src0> got nearest size 816x616
> 0:00:01.938250889 20954  0x15ffe90 ERROR                   v4l2 gstv4l2object.c:1873:gst_v4l2_object_get_interlace_mode: Driver bug detected - check driver with v4l2-compliance from http://git.linuxtv.org/v4l-utils.git
> 0:00:01.938326893 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2708:gst_v4l2_object_get_nearest_size:<v4l2src0> getting nearest size to 32768x32768 with format RGGB
> 0:00:01.938431566 20954  0x15ffe90 LOG                     v4l2 gstv4l2object.c:2724:gst_v4l2_object_get_nearest_size:<v4l2src0> got nearest size 816x616
> 0:00:01.939776641 20954  0x15ffe90 ERROR                   v4l2 gstv4l2object.c:1873:gst_v4l2_object_get_interlace_mode: Driver bug detected - check driver with v4l2-compliance from http://git.linuxtv.org/v4l-utils.git
> 0:00:01.940110660 20954  0x15ffe90 DEBUG                   v4l2 gstv4l2object.c:1955:gst_v4l2_object_get_colorspace: Unknown enum v4l2_colorspace 0
>
>     This triggers the "/* Since we can't get framerate directly, try to
>     use the current norm */" code in v4l2object.c, which causes it to
>     select one of the 30000/1001 norms:
>
> 0:00:01.955927879 20954  0x15ffe90 INFO                    v4l2 gstv4l2object.c:3811:gst_v4l2_object_get_caps:<v4l2src0> probed caps: video/x-bayer, format=(string)rggb, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)I420, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)YV12, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)BGR, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(st
 ring)RGB, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1
>
>     despite the media pipeline actually being configured for 60fps.
>
>     Forcing it by adjusting the pipeline only results in gstreamer
>     failing, because it believes that v4l2 is unable to operate at
>     60fps.
>
>     Also note the complaints from v4l2src about the non-compliance...

Thanks, I've fixed most of v4l2-compliance issues, but this is not
done yet. Is that something you can help with?

Steve


[-- Attachment #2: udpstream.sh --]
[-- Type: application/x-shellscript, Size: 381 bytes --]

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> Can you share your gstreamer pipeline? For now, until
> VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
> does not attempt to specify a frame rate. I use the attached
> script for testing, which works for me.

It's nothing more than

  gst-launch-1.0 -v v4l2src ! <any needed conversions> ! xvimagesink

in my case, the conversions are bayer2rgbneon.  However, this only shows
you the frame rate negotiated on the pads (which is actually good enough
to show the issue.)

How I stumbled across though this was when I was trying to encode:

 gst-launch-1.0 v4l2src device=/dev/video9 ! bayer2rgbneon ! \
	videoconvert ! x264enc speed-preset=1 ! avimux ! \
	filesink location=test.avi

I noticed that vlc would always say it was playing the resulting AVI
at 30fps.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> Can you share your gstreamer pipeline? For now, until
> VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
> does not attempt to specify a frame rate. I use the attached
> script for testing, which works for me.

It's nothing more than

  gst-launch-1.0 -v v4l2src ! <any needed conversions> ! xvimagesink

in my case, the conversions are bayer2rgbneon.  However, this only shows
you the frame rate negotiated on the pads (which is actually good enough
to show the issue.)

How I stumbled across though this was when I was trying to encode:

 gst-launch-1.0 v4l2src device=/dev/video9 ! bayer2rgbneon ! \
	videoconvert ! x264enc speed-preset=1 ! avimux ! \
	filesink location=test.avi

I noticed that vlc would always say it was playing the resulting AVI
at 30fps.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> Can you share your gstreamer pipeline? For now, until
> VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
> does not attempt to specify a frame rate. I use the attached
> script for testing, which works for me.

It's nothing more than

  gst-launch-1.0 -v v4l2src ! <any needed conversions> ! xvimagesink

in my case, the conversions are bayer2rgbneon.  However, this only shows
you the frame rate negotiated on the pads (which is actually good enough
to show the issue.)

How I stumbled across though this was when I was trying to encode:

 gst-launch-1.0 v4l2src device=/dev/video9 ! bayer2rgbneon ! \
	videoconvert ! x264enc speed-preset=1 ! avimux ! \
	filesink location=test.avi

I noticed that vlc would always say it was playing the resulting AVI
at 30fps.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Nicolas Dufresne]

[-- Attachment #1: Type: text/plain, Size: 1451 bytes --]

Le samedi 18 mars 2017 à 20:43 +0000, Russell King - ARM Linux a
écrit :
> On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> > Can you share your gstreamer pipeline? For now, until
> > VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
> > does not attempt to specify a frame rate. I use the attached
> > script for testing, which works for me.
> 
> It's nothing more than
> 
>   gst-launch-1.0 -v v4l2src ! <any needed conversions> ! xvimagesink
> 
> in my case, the conversions are bayer2rgbneon.  However, this only
> shows
> you the frame rate negotiated on the pads (which is actually good
> enough
> to show the issue.)
> 
> How I stumbled across though this was when I was trying to encode:
> 
>  gst-launch-1.0 v4l2src device=/dev/video9 ! bayer2rgbneon ! \
>         videoconvert ! x264enc speed-preset=1 ! avimux ! \
>         filesink location=test.avi
> 
> I noticed that vlc would always say it was playing the resulting AVI
> at 30fps.

In practice, I have the impression there is a fair reason why framerate
enumeration isn't implemented (considering there is only 1 valid rate).
Along with the norm fallback, GStreamer could could also consider the
currently set framerate as returned by VIDIOC_G_PARM. At the same time,
implementing that enumeration shall be straightforward, and will make a
large amount of existing userspace work.

regards,
Nicolas

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

[PATCH v5 00/39] i.MX Media Driver

[Nicolas Dufresne]

Le samedi 18 mars 2017 ? 20:43 +0000, Russell King - ARM Linux a
?crit?:
> On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> > Can you share your gstreamer pipeline? For now, until
> > VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
> > does not attempt to specify a frame rate. I use the attached
> > script for testing, which works for me.
> 
> It's nothing more than
> 
> ? gst-launch-1.0 -v v4l2src ! <any needed conversions> ! xvimagesink
> 
> in my case, the conversions are bayer2rgbneon.? However, this only
> shows
> you the frame rate negotiated on the pads (which is actually good
> enough
> to show the issue.)
> 
> How I stumbled across though this was when I was trying to encode:
> 
> ?gst-launch-1.0 v4l2src device=/dev/video9 ! bayer2rgbneon ! \
> ????????videoconvert ! x264enc speed-preset=1 ! avimux ! \
> ????????filesink location=test.avi
> 
> I noticed that vlc would always say it was playing the resulting AVI
> at 30fps.

In practice, I have the impression there is a fair reason why framerate
enumeration isn't implemented (considering there is only 1 valid rate).
Along with the norm fallback, GStreamer could could also consider the
currently set framerate as returned by?VIDIOC_G_PARM. At the same time,
implementing that enumeration shall be straightforward, and will make a
large amount of existing userspace work.

regards,
Nicolas
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 181 bytes
Desc: This is a digitally signed message part
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170318/9bd83c41/attachment.sig>

Re: [PATCH v5 00/39] i.MX Media Driver

[Nicolas Dufresne]

[-- Attachment #1: Type: text/plain, Size: 1451 bytes --]

Le samedi 18 mars 2017 à 20:43 +0000, Russell King - ARM Linux a
écrit :
> On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> > Can you share your gstreamer pipeline? For now, until
> > VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
> > does not attempt to specify a frame rate. I use the attached
> > script for testing, which works for me.
> 
> It's nothing more than
> 
>   gst-launch-1.0 -v v4l2src ! <any needed conversions> ! xvimagesink
> 
> in my case, the conversions are bayer2rgbneon.  However, this only
> shows
> you the frame rate negotiated on the pads (which is actually good
> enough
> to show the issue.)
> 
> How I stumbled across though this was when I was trying to encode:
> 
>  gst-launch-1.0 v4l2src device=/dev/video9 ! bayer2rgbneon ! \
>         videoconvert ! x264enc speed-preset=1 ! avimux ! \
>         filesink location=test.avi
> 
> I noticed that vlc would always say it was playing the resulting AVI
> at 30fps.

In practice, I have the impression there is a fair reason why framerate
enumeration isn't implemented (considering there is only 1 valid rate).
Along with the norm fallback, GStreamer could could also consider the
currently set framerate as returned by VIDIOC_G_PARM. At the same time,
implementing that enumeration shall be straightforward, and will make a
large amount of existing userspace work.

regards,
Nicolas

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sat, Mar 18, 2017 at 08:41:14PM -0400, Nicolas Dufresne wrote:
> Le samedi 18 mars 2017 à 20:43 +0000, Russell King - ARM Linux a
> écrit :
> > On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> > > Can you share your gstreamer pipeline? For now, until
> > > VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
> > > does not attempt to specify a frame rate. I use the attached
> > > script for testing, which works for me.
> > 
> > It's nothing more than
> > 
> >   gst-launch-1.0 -v v4l2src ! <any needed conversions> ! xvimagesink
> > 
> > in my case, the conversions are bayer2rgbneon.  However, this only
> > shows
> > you the frame rate negotiated on the pads (which is actually good
> > enough
> > to show the issue.)
> > 
> > How I stumbled across though this was when I was trying to encode:
> > 
> >  gst-launch-1.0 v4l2src device=/dev/video9 ! bayer2rgbneon ! \
> >         videoconvert ! x264enc speed-preset=1 ! avimux ! \
> >         filesink location=test.avi
> > 
> > I noticed that vlc would always say it was playing the resulting AVI
> > at 30fps.
> 
> In practice, I have the impression there is a fair reason why framerate
> enumeration isn't implemented (considering there is only 1 valid rate).

That's actually completely incorrect.

With the capture device interfacing directly with CSI, it's possible
_today_ to select:

* the CSI sink pad's resolution
* the CSI sink pad's resolution with the width and/or height halved
* the CSI sink pad's frame rate
* the CSI sink pad's frame rate divided by the frame drop factor

To put it another way, these are possible:

# v4l2-ctl -d /dev/video10 --list-formats-ext
ioctl: VIDIOC_ENUM_FMT
        Index       : 0
        Type        : Video Capture
        Pixel Format: 'RGGB'
        Name        : 8-bit Bayer RGRG/GBGB
                Size: Discrete 816x616
                        Interval: Discrete 0.040s (25.000 fps)
                        Interval: Discrete 0.048s (20.833 fps)
                        Interval: Discrete 0.050s (20.000 fps)
                        Interval: Discrete 0.053s (18.750 fps)
                        Interval: Discrete 0.060s (16.667 fps)
                        Interval: Discrete 0.067s (15.000 fps)
                        Interval: Discrete 0.080s (12.500 fps)
                        Interval: Discrete 0.100s (10.000 fps)
                        Interval: Discrete 0.120s (8.333 fps)
                        Interval: Discrete 0.160s (6.250 fps)
                        Interval: Discrete 0.200s (5.000 fps)
                        Interval: Discrete 0.240s (4.167 fps)
                Size: Discrete 408x616
<same intervals>
                Size: Discrete 816x308
<same intervals>
                Size: Discrete 408x308
<same intervals>

These don't become possible as a result of implementing the enums,
they're all already requestable through /dev/video10.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sat, Mar 18, 2017 at 08:41:14PM -0400, Nicolas Dufresne wrote:
> Le samedi 18 mars 2017 ? 20:43 +0000, Russell King - ARM Linux a
> ?crit?:
> > On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> > > Can you share your gstreamer pipeline? For now, until
> > > VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
> > > does not attempt to specify a frame rate. I use the attached
> > > script for testing, which works for me.
> > 
> > It's nothing more than
> > 
> > ? gst-launch-1.0 -v v4l2src ! <any needed conversions> ! xvimagesink
> > 
> > in my case, the conversions are bayer2rgbneon.? However, this only
> > shows
> > you the frame rate negotiated on the pads (which is actually good
> > enough
> > to show the issue.)
> > 
> > How I stumbled across though this was when I was trying to encode:
> > 
> > ?gst-launch-1.0 v4l2src device=/dev/video9 ! bayer2rgbneon ! \
> > ????????videoconvert ! x264enc speed-preset=1 ! avimux ! \
> > ????????filesink location=test.avi
> > 
> > I noticed that vlc would always say it was playing the resulting AVI
> > at 30fps.
> 
> In practice, I have the impression there is a fair reason why framerate
> enumeration isn't implemented (considering there is only 1 valid rate).

That's actually completely incorrect.

With the capture device interfacing directly with CSI, it's possible
_today_ to select:

* the CSI sink pad's resolution
* the CSI sink pad's resolution with the width and/or height halved
* the CSI sink pad's frame rate
* the CSI sink pad's frame rate divided by the frame drop factor

To put it another way, these are possible:

# v4l2-ctl -d /dev/video10 --list-formats-ext
ioctl: VIDIOC_ENUM_FMT
        Index       : 0
        Type        : Video Capture
        Pixel Format: 'RGGB'
        Name        : 8-bit Bayer RGRG/GBGB
                Size: Discrete 816x616
                        Interval: Discrete 0.040s (25.000 fps)
                        Interval: Discrete 0.048s (20.833 fps)
                        Interval: Discrete 0.050s (20.000 fps)
                        Interval: Discrete 0.053s (18.750 fps)
                        Interval: Discrete 0.060s (16.667 fps)
                        Interval: Discrete 0.067s (15.000 fps)
                        Interval: Discrete 0.080s (12.500 fps)
                        Interval: Discrete 0.100s (10.000 fps)
                        Interval: Discrete 0.120s (8.333 fps)
                        Interval: Discrete 0.160s (6.250 fps)
                        Interval: Discrete 0.200s (5.000 fps)
                        Interval: Discrete 0.240s (4.167 fps)
                Size: Discrete 408x616
<same intervals>
                Size: Discrete 816x308
<same intervals>
                Size: Discrete 408x308
<same intervals>

These don't become possible as a result of implementing the enums,
they're all already requestable through /dev/video10.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sat, Mar 18, 2017 at 08:41:14PM -0400, Nicolas Dufresne wrote:
> Le samedi 18 mars 2017 à 20:43 +0000, Russell King - ARM Linux a
> écrit :
> > On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> > > Can you share your gstreamer pipeline? For now, until
> > > VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
> > > does not attempt to specify a frame rate. I use the attached
> > > script for testing, which works for me.
> > 
> > It's nothing more than
> > 
> >   gst-launch-1.0 -v v4l2src ! <any needed conversions> ! xvimagesink
> > 
> > in my case, the conversions are bayer2rgbneon.  However, this only
> > shows
> > you the frame rate negotiated on the pads (which is actually good
> > enough
> > to show the issue.)
> > 
> > How I stumbled across though this was when I was trying to encode:
> > 
> >  gst-launch-1.0 v4l2src device=/dev/video9 ! bayer2rgbneon ! \
> >         videoconvert ! x264enc speed-preset=1 ! avimux ! \
> >         filesink location=test.avi
> > 
> > I noticed that vlc would always say it was playing the resulting AVI
> > at 30fps.
> 
> In practice, I have the impression there is a fair reason why framerate
> enumeration isn't implemented (considering there is only 1 valid rate).

That's actually completely incorrect.

With the capture device interfacing directly with CSI, it's possible
_today_ to select:

* the CSI sink pad's resolution
* the CSI sink pad's resolution with the width and/or height halved
* the CSI sink pad's frame rate
* the CSI sink pad's frame rate divided by the frame drop factor

To put it another way, these are possible:

# v4l2-ctl -d /dev/video10 --list-formats-ext
ioctl: VIDIOC_ENUM_FMT
        Index       : 0
        Type        : Video Capture
        Pixel Format: 'RGGB'
        Name        : 8-bit Bayer RGRG/GBGB
                Size: Discrete 816x616
                        Interval: Discrete 0.040s (25.000 fps)
                        Interval: Discrete 0.048s (20.833 fps)
                        Interval: Discrete 0.050s (20.000 fps)
                        Interval: Discrete 0.053s (18.750 fps)
                        Interval: Discrete 0.060s (16.667 fps)
                        Interval: Discrete 0.067s (15.000 fps)
                        Interval: Discrete 0.080s (12.500 fps)
                        Interval: Discrete 0.100s (10.000 fps)
                        Interval: Discrete 0.120s (8.333 fps)
                        Interval: Discrete 0.160s (6.250 fps)
                        Interval: Discrete 0.200s (5.000 fps)
                        Interval: Discrete 0.240s (4.167 fps)
                Size: Discrete 408x616
<same intervals>
                Size: Discrete 816x308
<same intervals>
                Size: Discrete 408x308
<same intervals>

These don't become possible as a result of implementing the enums,
they're all already requestable through /dev/video10.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Nicolas Dufresne]

[-- Attachment #1: Type: text/plain, Size: 2984 bytes --]

Le dimanche 19 mars 2017 à 00:54 +0000, Russell King - ARM Linux a
écrit :
> > 
> > In practice, I have the impression there is a fair reason why
> > framerate
> > enumeration isn't implemented (considering there is only 1 valid
> > rate).
> 
> That's actually completely incorrect.
> 
> With the capture device interfacing directly with CSI, it's possible
> _today_ to select:
> 
> * the CSI sink pad's resolution
> * the CSI sink pad's resolution with the width and/or height halved
> * the CSI sink pad's frame rate
> * the CSI sink pad's frame rate divided by the frame drop factor
> 
> To put it another way, these are possible:
> 
> # v4l2-ctl -d /dev/video10 --list-formats-ext
> ioctl: VIDIOC_ENUM_FMT
>         Index       : 0
>         Type        : Video Capture
>         Pixel Format: 'RGGB'
>         Name        : 8-bit Bayer RGRG/GBGB
>                 Size: Discrete 816x616
>                         Interval: Discrete 0.040s (25.000 fps)
>                         Interval: Discrete 0.048s (20.833 fps)
>                         Interval: Discrete 0.050s (20.000 fps)
>                         Interval: Discrete 0.053s (18.750 fps)
>                         Interval: Discrete 0.060s (16.667 fps)
>                         Interval: Discrete 0.067s (15.000 fps)
>                         Interval: Discrete 0.080s (12.500 fps)
>                         Interval: Discrete 0.100s (10.000 fps)
>                         Interval: Discrete 0.120s (8.333 fps)
>                         Interval: Discrete 0.160s (6.250 fps)
>                         Interval: Discrete 0.200s (5.000 fps)
>                         Interval: Discrete 0.240s (4.167 fps)
>                 Size: Discrete 408x616
> <same intervals>
>                 Size: Discrete 816x308
> <same intervals>
>                 Size: Discrete 408x308
> <same intervals>
> 
> These don't become possible as a result of implementing the enums,
> they're all already requestable through /dev/video10.

Ok that wasn't clear. So basically video9 is a front-end to video10,
and it does not proxy the enumerations. I understand this is what you
are now fixing. And this has to be fixed, because I can image cases
where the front-end could support only a subset of the sub-dev. So
having userspace enumerate on another device (and having to find this
device by walking the tree) is unlikely to work in all scenarios.

regards,
Nicolas

p.s. This is why caps negotiation is annoyingly complex in GStreamer,
specially that there is no shortcut, you connect pads, and they figure-
out what format they will use between each other.

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

[PATCH v5 00/39] i.MX Media Driver

[Nicolas Dufresne]

Le dimanche 19 mars 2017 ? 00:54 +0000, Russell King - ARM Linux a
?crit?:
> > 
> > In practice, I have the impression there is a fair reason why
> > framerate
> > enumeration isn't implemented (considering there is only 1 valid
> > rate).
> 
> That's actually completely incorrect.
> 
> With the capture device interfacing directly with CSI, it's possible
> _today_ to select:
> 
> * the CSI sink pad's resolution
> * the CSI sink pad's resolution with the width and/or height halved
> * the CSI sink pad's frame rate
> * the CSI sink pad's frame rate divided by the frame drop factor
> 
> To put it another way, these are possible:
> 
> # v4l2-ctl -d /dev/video10 --list-formats-ext
> ioctl: VIDIOC_ENUM_FMT
> ??????? Index?????? : 0
> ??????? Type??????? : Video Capture
> ??????? Pixel Format: 'RGGB'
> ??????? Name??????? : 8-bit Bayer RGRG/GBGB
> ??????????????? Size: Discrete 816x616
> ??????????????????????? Interval: Discrete 0.040s (25.000 fps)
> ??????????????????????? Interval: Discrete 0.048s (20.833 fps)
> ??????????????????????? Interval: Discrete 0.050s (20.000 fps)
> ??????????????????????? Interval: Discrete 0.053s (18.750 fps)
> ??????????????????????? Interval: Discrete 0.060s (16.667 fps)
> ??????????????????????? Interval: Discrete 0.067s (15.000 fps)
> ??????????????????????? Interval: Discrete 0.080s (12.500 fps)
> ??????????????????????? Interval: Discrete 0.100s (10.000 fps)
> ??????????????????????? Interval: Discrete 0.120s (8.333 fps)
> ??????????????????????? Interval: Discrete 0.160s (6.250 fps)
> ??????????????????????? Interval: Discrete 0.200s (5.000 fps)
> ??????????????????????? Interval: Discrete 0.240s (4.167 fps)
> ??????????????? Size: Discrete 408x616
> <same intervals>
> ??????????????? Size: Discrete 816x308
> <same intervals>
> ??????????????? Size: Discrete 408x308
> <same intervals>
> 
> These don't become possible as a result of implementing the enums,
> they're all already requestable through /dev/video10.

Ok that wasn't clear. So basically video9 is a front-end to video10,
and it does not proxy the enumerations. I understand this is what you
are now fixing. And this has to be fixed, because I can image cases
where the front-end could support only a subset of the sub-dev. So
having userspace enumerate on another device (and having to find this
device by walking the tree) is unlikely to work in all scenarios.

regards,
Nicolas

p.s. This is why caps negotiation is annoyingly complex in GStreamer,
specially that there is no shortcut, you connect pads, and they figure-
out what format they will use between each other.
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 181 bytes
Desc: This is a digitally signed message part
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170319/b0407c9d/attachment-0001.sig>

Re: [PATCH v5 00/39] i.MX Media Driver

[Nicolas Dufresne]

[-- Attachment #1.1: Type: text/plain, Size: 2984 bytes --]

Le dimanche 19 mars 2017 à 00:54 +0000, Russell King - ARM Linux a
écrit :
> > 
> > In practice, I have the impression there is a fair reason why
> > framerate
> > enumeration isn't implemented (considering there is only 1 valid
> > rate).
> 
> That's actually completely incorrect.
> 
> With the capture device interfacing directly with CSI, it's possible
> _today_ to select:
> 
> * the CSI sink pad's resolution
> * the CSI sink pad's resolution with the width and/or height halved
> * the CSI sink pad's frame rate
> * the CSI sink pad's frame rate divided by the frame drop factor
> 
> To put it another way, these are possible:
> 
> # v4l2-ctl -d /dev/video10 --list-formats-ext
> ioctl: VIDIOC_ENUM_FMT
>         Index       : 0
>         Type        : Video Capture
>         Pixel Format: 'RGGB'
>         Name        : 8-bit Bayer RGRG/GBGB
>                 Size: Discrete 816x616
>                         Interval: Discrete 0.040s (25.000 fps)
>                         Interval: Discrete 0.048s (20.833 fps)
>                         Interval: Discrete 0.050s (20.000 fps)
>                         Interval: Discrete 0.053s (18.750 fps)
>                         Interval: Discrete 0.060s (16.667 fps)
>                         Interval: Discrete 0.067s (15.000 fps)
>                         Interval: Discrete 0.080s (12.500 fps)
>                         Interval: Discrete 0.100s (10.000 fps)
>                         Interval: Discrete 0.120s (8.333 fps)
>                         Interval: Discrete 0.160s (6.250 fps)
>                         Interval: Discrete 0.200s (5.000 fps)
>                         Interval: Discrete 0.240s (4.167 fps)
>                 Size: Discrete 408x616
> <same intervals>
>                 Size: Discrete 816x308
> <same intervals>
>                 Size: Discrete 408x308
> <same intervals>
> 
> These don't become possible as a result of implementing the enums,
> they're all already requestable through /dev/video10.

Ok that wasn't clear. So basically video9 is a front-end to video10,
and it does not proxy the enumerations. I understand this is what you
are now fixing. And this has to be fixed, because I can image cases
where the front-end could support only a subset of the sub-dev. So
having userspace enumerate on another device (and having to find this
device by walking the tree) is unlikely to work in all scenarios.

regards,
Nicolas

p.s. This is why caps negotiation is annoyingly complex in GStreamer,
specially that there is no shortcut, you connect pads, and they figure-
out what format they will use between each other.

[-- Attachment #1.2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

[-- Attachment #2: Type: text/plain, Size: 169 bytes --]

_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 19, 2017 at 10:33:25AM -0400, Nicolas Dufresne wrote:
> Le dimanche 19 mars 2017 à 00:54 +0000, Russell King - ARM Linux a
> écrit :
> > > 
> > > In practice, I have the impression there is a fair reason why
> > > framerate
> > > enumeration isn't implemented (considering there is only 1 valid
> > > rate).
> > 
> > That's actually completely incorrect.
> > 
> > With the capture device interfacing directly with CSI, it's possible
> > _today_ to select:
> > 
> > * the CSI sink pad's resolution
> > * the CSI sink pad's resolution with the width and/or height halved
> > * the CSI sink pad's frame rate
> > * the CSI sink pad's frame rate divided by the frame drop factor
> > 
> > To put it another way, these are possible:
> > 
> > # v4l2-ctl -d /dev/video10 --list-formats-ext
> > ioctl: VIDIOC_ENUM_FMT
> >         Index       : 0
> >         Type        : Video Capture
> >         Pixel Format: 'RGGB'
> >         Name        : 8-bit Bayer RGRG/GBGB
> >                 Size: Discrete 816x616
> >                         Interval: Discrete 0.040s (25.000 fps)
> >                         Interval: Discrete 0.048s (20.833 fps)
> >                         Interval: Discrete 0.050s (20.000 fps)
> >                         Interval: Discrete 0.053s (18.750 fps)
> >                         Interval: Discrete 0.060s (16.667 fps)
> >                         Interval: Discrete 0.067s (15.000 fps)
> >                         Interval: Discrete 0.080s (12.500 fps)
> >                         Interval: Discrete 0.100s (10.000 fps)
> >                         Interval: Discrete 0.120s (8.333 fps)
> >                         Interval: Discrete 0.160s (6.250 fps)
> >                         Interval: Discrete 0.200s (5.000 fps)
> >                         Interval: Discrete 0.240s (4.167 fps)
> >                 Size: Discrete 408x616
> > <same intervals>
> >                 Size: Discrete 816x308
> > <same intervals>
> >                 Size: Discrete 408x308
> > <same intervals>
> > 
> > These don't become possible as a result of implementing the enums,
> > they're all already requestable through /dev/video10.
> 
> Ok that wasn't clear. So basically video9 is a front-end to video10,
> and it does not proxy the enumerations.

No.  We've sent .dot graphs which show the structure of the imx capture
driver.

What we have wrt video nodes is (eg):

sensor --->  csi2 ----> mux ---> csi ----+------> csi capture
subdev      subdev    subdev    subdev   |       /dev/video10
                                         |
                                         +---------\
                                         |          \
                                         +--> vdic ---> ic_prpenc ---> ic_prpenc
                                             subdev     subdev         capture

... etc ... for full details, see the .dot diagrams that have been
sent (sorry I can't recall where they are in the threads.)

> I understand this is what you
> are now fixing. And this has to be fixed, because I can image cases
> where the front-end could support only a subset of the sub-dev. So
> having userspace enumerate on another device (and having to find this
> device by walking the tree) is unlikely to work in all scenarios.

The capture blocks (imx-media-capture) all talk to their immediate
upstream subdev and configure its source pad according to the formats,
frame size and frame interval requested by the capture application.
The subdev source pad decides whether the request is valid, and allows
it, modifies it or rejects it as appropriate.

Without working enumeration support, there's no way for an application
to find out what possible settings there are, and, as I've already
explained, the CSI subdev is capable itself of two things:

* Scaling down the image by a factor of two independently in the
  horizontal and vertical directions
* Deterministically dropping frames received from its upstream
  element, thereby reducing the frame rate.

> p.s. This is why caps negotiation is annoyingly complex in GStreamer,
> specially that there is no shortcut, you connect pads, and they figure-
> out what format they will use between each other.

Right, so when you specify video/x-raw,...,framerate=60/1 it introduces
a new element which has one source and sink pad, which only supports
the specification given.  If the neighbour's pad doesn't support it,
gstreamer fails because the caps negotiation fails.

So, if v4l2src believes (via the tvnorms, because it's lacking any
other information) that the capture device can only do 25fps and
30fps, then trying to set 60fps _even if S_PARM may accept it_ will
cause gstreamer to fail - because v4l2src can only advertise that
it supports a source of 25fps and 30fps.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 19, 2017 at 10:33:25AM -0400, Nicolas Dufresne wrote:
> Le dimanche 19 mars 2017 ? 00:54 +0000, Russell King - ARM Linux a
> ?crit?:
> > > 
> > > In practice, I have the impression there is a fair reason why
> > > framerate
> > > enumeration isn't implemented (considering there is only 1 valid
> > > rate).
> > 
> > That's actually completely incorrect.
> > 
> > With the capture device interfacing directly with CSI, it's possible
> > _today_ to select:
> > 
> > * the CSI sink pad's resolution
> > * the CSI sink pad's resolution with the width and/or height halved
> > * the CSI sink pad's frame rate
> > * the CSI sink pad's frame rate divided by the frame drop factor
> > 
> > To put it another way, these are possible:
> > 
> > # v4l2-ctl -d /dev/video10 --list-formats-ext
> > ioctl: VIDIOC_ENUM_FMT
> > ??????? Index?????? : 0
> > ??????? Type??????? : Video Capture
> > ??????? Pixel Format: 'RGGB'
> > ??????? Name??????? : 8-bit Bayer RGRG/GBGB
> > ??????????????? Size: Discrete 816x616
> > ??????????????????????? Interval: Discrete 0.040s (25.000 fps)
> > ??????????????????????? Interval: Discrete 0.048s (20.833 fps)
> > ??????????????????????? Interval: Discrete 0.050s (20.000 fps)
> > ??????????????????????? Interval: Discrete 0.053s (18.750 fps)
> > ??????????????????????? Interval: Discrete 0.060s (16.667 fps)
> > ??????????????????????? Interval: Discrete 0.067s (15.000 fps)
> > ??????????????????????? Interval: Discrete 0.080s (12.500 fps)
> > ??????????????????????? Interval: Discrete 0.100s (10.000 fps)
> > ??????????????????????? Interval: Discrete 0.120s (8.333 fps)
> > ??????????????????????? Interval: Discrete 0.160s (6.250 fps)
> > ??????????????????????? Interval: Discrete 0.200s (5.000 fps)
> > ??????????????????????? Interval: Discrete 0.240s (4.167 fps)
> > ??????????????? Size: Discrete 408x616
> > <same intervals>
> > ??????????????? Size: Discrete 816x308
> > <same intervals>
> > ??????????????? Size: Discrete 408x308
> > <same intervals>
> > 
> > These don't become possible as a result of implementing the enums,
> > they're all already requestable through /dev/video10.
> 
> Ok that wasn't clear. So basically video9 is a front-end to video10,
> and it does not proxy the enumerations.

No.  We've sent .dot graphs which show the structure of the imx capture
driver.

What we have wrt video nodes is (eg):

sensor --->  csi2 ----> mux ---> csi ----+------> csi capture
subdev      subdev    subdev    subdev   |       /dev/video10
                                         |
                                         +---------\
                                         |          \
                                         +--> vdic ---> ic_prpenc ---> ic_prpenc
                                             subdev     subdev         capture

... etc ... for full details, see the .dot diagrams that have been
sent (sorry I can't recall where they are in the threads.)

> I understand this is what you
> are now fixing. And this has to be fixed, because I can image cases
> where the front-end could support only a subset of the sub-dev. So
> having userspace enumerate on another device (and having to find this
> device by walking the tree) is unlikely to work in all scenarios.

The capture blocks (imx-media-capture) all talk to their immediate
upstream subdev and configure its source pad according to the formats,
frame size and frame interval requested by the capture application.
The subdev source pad decides whether the request is valid, and allows
it, modifies it or rejects it as appropriate.

Without working enumeration support, there's no way for an application
to find out what possible settings there are, and, as I've already
explained, the CSI subdev is capable itself of two things:

* Scaling down the image by a factor of two independently in the
  horizontal and vertical directions
* Deterministically dropping frames received from its upstream
  element, thereby reducing the frame rate.

> p.s. This is why caps negotiation is annoyingly complex in GStreamer,
> specially that there is no shortcut, you connect pads, and they figure-
> out what format they will use between each other.

Right, so when you specify video/x-raw,...,framerate=60/1 it introduces
a new element which has one source and sink pad, which only supports
the specification given.  If the neighbour's pad doesn't support it,
gstreamer fails because the caps negotiation fails.

So, if v4l2src believes (via the tvnorms, because it's lacking any
other information) that the capture device can only do 25fps and
30fps, then trying to set 60fps _even if S_PARM may accept it_ will
cause gstreamer to fail - because v4l2src can only advertise that
it supports a source of 25fps and 30fps.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 19, 2017 at 10:33:25AM -0400, Nicolas Dufresne wrote:
> Le dimanche 19 mars 2017 à 00:54 +0000, Russell King - ARM Linux a
> écrit :
> > > 
> > > In practice, I have the impression there is a fair reason why
> > > framerate
> > > enumeration isn't implemented (considering there is only 1 valid
> > > rate).
> > 
> > That's actually completely incorrect.
> > 
> > With the capture device interfacing directly with CSI, it's possible
> > _today_ to select:
> > 
> > * the CSI sink pad's resolution
> > * the CSI sink pad's resolution with the width and/or height halved
> > * the CSI sink pad's frame rate
> > * the CSI sink pad's frame rate divided by the frame drop factor
> > 
> > To put it another way, these are possible:
> > 
> > # v4l2-ctl -d /dev/video10 --list-formats-ext
> > ioctl: VIDIOC_ENUM_FMT
> >         Index       : 0
> >         Type        : Video Capture
> >         Pixel Format: 'RGGB'
> >         Name        : 8-bit Bayer RGRG/GBGB
> >                 Size: Discrete 816x616
> >                         Interval: Discrete 0.040s (25.000 fps)
> >                         Interval: Discrete 0.048s (20.833 fps)
> >                         Interval: Discrete 0.050s (20.000 fps)
> >                         Interval: Discrete 0.053s (18.750 fps)
> >                         Interval: Discrete 0.060s (16.667 fps)
> >                         Interval: Discrete 0.067s (15.000 fps)
> >                         Interval: Discrete 0.080s (12.500 fps)
> >                         Interval: Discrete 0.100s (10.000 fps)
> >                         Interval: Discrete 0.120s (8.333 fps)
> >                         Interval: Discrete 0.160s (6.250 fps)
> >                         Interval: Discrete 0.200s (5.000 fps)
> >                         Interval: Discrete 0.240s (4.167 fps)
> >                 Size: Discrete 408x616
> > <same intervals>
> >                 Size: Discrete 816x308
> > <same intervals>
> >                 Size: Discrete 408x308
> > <same intervals>
> > 
> > These don't become possible as a result of implementing the enums,
> > they're all already requestable through /dev/video10.
> 
> Ok that wasn't clear. So basically video9 is a front-end to video10,
> and it does not proxy the enumerations.

No.  We've sent .dot graphs which show the structure of the imx capture
driver.

What we have wrt video nodes is (eg):

sensor --->  csi2 ----> mux ---> csi ----+------> csi capture
subdev      subdev    subdev    subdev   |       /dev/video10
                                         |
                                         +---------\
                                         |          \
                                         +--> vdic ---> ic_prpenc ---> ic_prpenc
                                             subdev     subdev         capture

... etc ... for full details, see the .dot diagrams that have been
sent (sorry I can't recall where they are in the threads.)

> I understand this is what you
> are now fixing. And this has to be fixed, because I can image cases
> where the front-end could support only a subset of the sub-dev. So
> having userspace enumerate on another device (and having to find this
> device by walking the tree) is unlikely to work in all scenarios.

The capture blocks (imx-media-capture) all talk to their immediate
upstream subdev and configure its source pad according to the formats,
frame size and frame interval requested by the capture application.
The subdev source pad decides whether the request is valid, and allows
it, modifies it or rejects it as appropriate.

Without working enumeration support, there's no way for an application
to find out what possible settings there are, and, as I've already
explained, the CSI subdev is capable itself of two things:

* Scaling down the image by a factor of two independently in the
  horizontal and vertical directions
* Deterministically dropping frames received from its upstream
  element, thereby reducing the frame rate.

> p.s. This is why caps negotiation is annoyingly complex in GStreamer,
> specially that there is no shortcut, you connect pads, and they figure-
> out what format they will use between each other.

Right, so when you specify video/x-raw,...,framerate=60/1 it introduces
a new element which has one source and sink pad, which only supports
the specification given.  If the neighbour's pad doesn't support it,
gstreamer fails because the caps negotiation fails.

So, if v4l2src believes (via the tvnorms, because it's lacking any
other information) that the capture device can only do 25fps and
30fps, then trying to set 60fps _even if S_PARM may accept it_ will
cause gstreamer to fail - because v4l2src can only advertise that
it supports a source of 25fps and 30fps.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sat, Mar 18, 2017 at 08:41:14PM -0400, Nicolas Dufresne wrote:
> Along with the norm fallback, GStreamer could could also consider the
> currently set framerate as returned by VIDIOC_G_PARM. At the same time,
> implementing that enumeration shall be straightforward, and will make a
> large amount of existing userspace work.

Since, according to v4l2-compliance, providing the enumeration ioctls
appears to be optional:

1) should v4l2-compliance be checking whether other frame sizes/frame
   intervals are possible, and failing if the enumeration ioctls are
   not supported?

2) would it also make sense to allow gstreamer's v4l2src to try setting
   a these parameters, and only fail if it's unable to set it?  IOW, if
   I use:

gst-launch-1.0 v4l2src device=/dev/video10 ! \
	video/x-bayer,format=RGGB,framerate=20/1 ! ...

   where G_PARM says its currently configured for 25fps, but a S_PARM
   with 20fps would actually succeed.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sat, Mar 18, 2017 at 08:41:14PM -0400, Nicolas Dufresne wrote:
> Along with the norm fallback, GStreamer could could also consider the
> currently set framerate as returned by?VIDIOC_G_PARM. At the same time,
> implementing that enumeration shall be straightforward, and will make a
> large amount of existing userspace work.

Since, according to v4l2-compliance, providing the enumeration ioctls
appears to be optional:

1) should v4l2-compliance be checking whether other frame sizes/frame
   intervals are possible, and failing if the enumeration ioctls are
   not supported?

2) would it also make sense to allow gstreamer's v4l2src to try setting
   a these parameters, and only fail if it's unable to set it?  IOW, if
   I use:

gst-launch-1.0 v4l2src device=/dev/video10 ! \
	video/x-bayer,format=RGGB,framerate=20/1 ! ...

   where G_PARM says its currently configured for 25fps, but a S_PARM
   with 20fps would actually succeed.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sat, Mar 18, 2017 at 08:41:14PM -0400, Nicolas Dufresne wrote:
> Along with the norm fallback, GStreamer could could also consider the
> currently set framerate as returned by VIDIOC_G_PARM. At the same time,
> implementing that enumeration shall be straightforward, and will make a
> large amount of existing userspace work.

Since, according to v4l2-compliance, providing the enumeration ioctls
appears to be optional:

1) should v4l2-compliance be checking whether other frame sizes/frame
   intervals are possible, and failing if the enumeration ioctls are
   not supported?

2) would it also make sense to allow gstreamer's v4l2src to try setting
   a these parameters, and only fail if it's unable to set it?  IOW, if
   I use:

gst-launch-1.0 v4l2src device=/dev/video10 ! \
	video/x-bayer,format=RGGB,framerate=20/1 ! ...

   where G_PARM says its currently configured for 25fps, but a S_PARM
   with 20fps would actually succeed.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 00/39] i.MX Media Driver

[Nicolas Dufresne]

[-- Attachment #1: Type: text/plain, Size: 1817 bytes --]

Le dimanche 19 mars 2017 à 09:55 +0000, Russell King - ARM Linux a
écrit :
> 2) would it also make sense to allow gstreamer's v4l2src to try
> setting
>    a these parameters, and only fail if it's unable to set it?  IOW,
> if
>    I use:
> 
> gst-launch-1.0 v4l2src device=/dev/video10 ! \
>         video/x-bayer,format=RGGB,framerate=20/1 ! ...
> 
>    where G_PARM says its currently configured for 25fps, but a S_PARM
>    with 20fps would actually succeed.

In current design, v4l2src will "probe" all possible formats, cache
this, and use this information for negotiation. So after the caps has
been probed, there will be no TRY_FMT or anything like this happening
until it's too late. You have spotted a bug though, it should be
reading back the parm structure to validate (and probably produce a
not-negotiated error here).

Recently, specially for the IMX work done by Pengutronix, there was
contributions to enhance this probing to support probing capabilities
that are not enumerable (e.g. interlacing, colorimetry) using TRY_FMT.
There is no TRY_PARM in the API to implement similar fallback. Also,
those ended up creating a massive disaster for slow cameras. We now
have UVC cameras that takes 6s or more to start. I have no other choice
but to rewrite that now. We will negotiate the non-enumerable at the
last minute with TRY_FMT (when the subset is at it's smallest). This
will by accident add support for this camera interface, but that wasn't
the goal. It would still fail with application that enumerates the
possible resolutions and framerate and let you select them with a drop-
down (like cheese). In general, I can only conclude that making
everything that matter enumerable is the only working way to go for
generic userspace. 

Nicolas

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

[PATCH v5 00/39] i.MX Media Driver

[Nicolas Dufresne]

Le dimanche 19 mars 2017 ? 09:55 +0000, Russell King - ARM Linux a
?crit?:
> 2) would it also make sense to allow gstreamer's v4l2src to try
> setting
> ?? a these parameters, and only fail if it's unable to set it?? IOW,
> if
> ?? I use:
> 
> gst-launch-1.0 v4l2src device=/dev/video10 ! \
> ????????video/x-bayer,format=RGGB,framerate=20/1 ! ...
> 
> ?? where G_PARM says its currently configured for 25fps, but a S_PARM
> ?? with 20fps would actually succeed.

In current design, v4l2src will "probe" all possible formats, cache
this, and use this information for negotiation. So after the caps has
been probed, there will be no TRY_FMT or anything like this happening
until it's too late. You have spotted a bug though, it should be
reading back the parm structure to validate (and probably produce a
not-negotiated error here).

Recently, specially for the IMX work done by Pengutronix, there was
contributions to enhance this probing to support probing capabilities
that are not enumerable (e.g. interlacing, colorimetry) using TRY_FMT.
There is no TRY_PARM in the API to implement similar fallback. Also,
those ended up creating a massive disaster for slow cameras. We now
have UVC cameras that takes 6s or more to start. I have no other choice
but to rewrite that now. We will negotiate the non-enumerable at the
last minute with TRY_FMT (when the subset is at it's smallest). This
will by accident add support for this camera interface, but that wasn't
the goal. It would still fail with application that enumerates the
possible resolutions and framerate and let you select them with a drop-
down (like cheese). In general, I can only conclude that making
everything that matter enumerable is the only working way to go for
generic userspace. 

Nicolas
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 181 bytes
Desc: This is a digitally signed message part
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170319/efd02a55/attachment.sig>

Re: [PATCH v5 00/39] i.MX Media Driver

[Nicolas Dufresne]

[-- Attachment #1.1: Type: text/plain, Size: 1817 bytes --]

Le dimanche 19 mars 2017 à 09:55 +0000, Russell King - ARM Linux a
écrit :
> 2) would it also make sense to allow gstreamer's v4l2src to try
> setting
>    a these parameters, and only fail if it's unable to set it?  IOW,
> if
>    I use:
> 
> gst-launch-1.0 v4l2src device=/dev/video10 ! \
>         video/x-bayer,format=RGGB,framerate=20/1 ! ...
> 
>    where G_PARM says its currently configured for 25fps, but a S_PARM
>    with 20fps would actually succeed.

In current design, v4l2src will "probe" all possible formats, cache
this, and use this information for negotiation. So after the caps has
been probed, there will be no TRY_FMT or anything like this happening
until it's too late. You have spotted a bug though, it should be
reading back the parm structure to validate (and probably produce a
not-negotiated error here).

Recently, specially for the IMX work done by Pengutronix, there was
contributions to enhance this probing to support probing capabilities
that are not enumerable (e.g. interlacing, colorimetry) using TRY_FMT.
There is no TRY_PARM in the API to implement similar fallback. Also,
those ended up creating a massive disaster for slow cameras. We now
have UVC cameras that takes 6s or more to start. I have no other choice
but to rewrite that now. We will negotiate the non-enumerable at the
last minute with TRY_FMT (when the subset is at it's smallest). This
will by accident add support for this camera interface, but that wasn't
the goal. It would still fail with application that enumerates the
possible resolutions and framerate and let you select them with a drop-
down (like cheese). In general, I can only conclude that making
everything that matter enumerable is the only working way to go for
generic userspace. 

Nicolas

[-- Attachment #1.2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

[-- Attachment #2: Type: text/plain, Size: 169 bytes --]

_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

Re: [PATCH v5 00/39] i.MX Media Driver

[Vladimir Zapolskiy]

Hi Russell,

On 03/18/2017 10:43 PM, Russell King - ARM Linux wrote:
> On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
>> Can you share your gstreamer pipeline? For now, until
>> VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
>> does not attempt to specify a frame rate. I use the attached
>> script for testing, which works for me.
> 
> It's nothing more than
> 
>   gst-launch-1.0 -v v4l2src ! <any needed conversions> ! xvimagesink
> 
> in my case, the conversions are bayer2rgbneon.  However, this only shows
> you the frame rate negotiated on the pads (which is actually good enough
> to show the issue.)

I'm sorry for potential offtopic, but is bayer2rgbneon element found in
any officially supported by GStreamer plugin? Can it be a point of
failure?

--
With best wishes,
Vladimir

[PATCH v5 00/39] i.MX Media Driver

[Vladimir Zapolskiy]

Hi Russell,

On 03/18/2017 10:43 PM, Russell King - ARM Linux wrote:
> On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
>> Can you share your gstreamer pipeline? For now, until
>> VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
>> does not attempt to specify a frame rate. I use the attached
>> script for testing, which works for me.
> 
> It's nothing more than
> 
>   gst-launch-1.0 -v v4l2src ! <any needed conversions> ! xvimagesink
> 
> in my case, the conversions are bayer2rgbneon.  However, this only shows
> you the frame rate negotiated on the pads (which is actually good enough
> to show the issue.)

I'm sorry for potential offtopic, but is bayer2rgbneon element found in
any officially supported by GStreamer plugin? Can it be a point of
failure?

--
With best wishes,
Vladimir

Re: [PATCH v5 00/39] i.MX Media Driver

[Vladimir Zapolskiy]

Hi Russell,

On 03/18/2017 10:43 PM, Russell King - ARM Linux wrote:
> On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
>> Can you share your gstreamer pipeline? For now, until
>> VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
>> does not attempt to specify a frame rate. I use the attached
>> script for testing, which works for me.
> 
> It's nothing more than
> 
>   gst-launch-1.0 -v v4l2src ! <any needed conversions> ! xvimagesink
> 
> in my case, the conversions are bayer2rgbneon.  However, this only shows
> you the frame rate negotiated on the pads (which is actually good enough
> to show the issue.)

I'm sorry for potential offtopic, but is bayer2rgbneon element found in
any officially supported by GStreamer plugin? Can it be a point of
failure?

--
With best wishes,
Vladimir
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 19, 2017 at 03:57:56PM +0200, Vladimir Zapolskiy wrote:
> Hi Russell,
> 
> On 03/18/2017 10:43 PM, Russell King - ARM Linux wrote:
> > On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> >> Can you share your gstreamer pipeline? For now, until
> >> VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
> >> does not attempt to specify a frame rate. I use the attached
> >> script for testing, which works for me.
> > 
> > It's nothing more than
> > 
> >   gst-launch-1.0 -v v4l2src ! <any needed conversions> ! xvimagesink
> > 
> > in my case, the conversions are bayer2rgbneon.  However, this only shows
> > you the frame rate negotiated on the pads (which is actually good enough
> > to show the issue.)
> 
> I'm sorry for potential offtopic, but is bayer2rgbneon element found in
> any officially supported by GStreamer plugin?

No it isn't.  Google is wonderful, please make use of planetary search
facilities.

> Can it be a point of failure?

There's a good reason why I dumped a full debug log using GST_DEBUG=*:9,
analysed it for the cause of the failure, and tried several different
pipelines, including the standard bayer2rgb plugin.

Please don't blame this on random stuff after analysis of the logs _and_
reading the appropriate plugin code has shown where the problem is.  I
know gstreamer can be very complex, but it's very possible to analyse
the cause of problems and pin them down with detailed logs in conjunction
with the source code.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 19, 2017 at 03:57:56PM +0200, Vladimir Zapolskiy wrote:
> Hi Russell,
> 
> On 03/18/2017 10:43 PM, Russell King - ARM Linux wrote:
> > On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> >> Can you share your gstreamer pipeline? For now, until
> >> VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
> >> does not attempt to specify a frame rate. I use the attached
> >> script for testing, which works for me.
> > 
> > It's nothing more than
> > 
> >   gst-launch-1.0 -v v4l2src ! <any needed conversions> ! xvimagesink
> > 
> > in my case, the conversions are bayer2rgbneon.  However, this only shows
> > you the frame rate negotiated on the pads (which is actually good enough
> > to show the issue.)
> 
> I'm sorry for potential offtopic, but is bayer2rgbneon element found in
> any officially supported by GStreamer plugin?

No it isn't.  Google is wonderful, please make use of planetary search
facilities.

> Can it be a point of failure?

There's a good reason why I dumped a full debug log using GST_DEBUG=*:9,
analysed it for the cause of the failure, and tried several different
pipelines, including the standard bayer2rgb plugin.

Please don't blame this on random stuff after analysis of the logs _and_
reading the appropriate plugin code has shown where the problem is.  I
know gstreamer can be very complex, but it's very possible to analyse
the cause of problems and pin them down with detailed logs in conjunction
with the source code.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 19, 2017 at 03:57:56PM +0200, Vladimir Zapolskiy wrote:
> Hi Russell,
> 
> On 03/18/2017 10:43 PM, Russell King - ARM Linux wrote:
> > On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> >> Can you share your gstreamer pipeline? For now, until
> >> VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
> >> does not attempt to specify a frame rate. I use the attached
> >> script for testing, which works for me.
> > 
> > It's nothing more than
> > 
> >   gst-launch-1.0 -v v4l2src ! <any needed conversions> ! xvimagesink
> > 
> > in my case, the conversions are bayer2rgbneon.  However, this only shows
> > you the frame rate negotiated on the pads (which is actually good enough
> > to show the issue.)
> 
> I'm sorry for potential offtopic, but is bayer2rgbneon element found in
> any officially supported by GStreamer plugin?

No it isn't.  Google is wonderful, please make use of planetary search
facilities.

> Can it be a point of failure?

There's a good reason why I dumped a full debug log using GST_DEBUG=*:9,
analysed it for the cause of the failure, and tried several different
pipelines, including the standard bayer2rgb plugin.

Please don't blame this on random stuff after analysis of the logs _and_
reading the appropriate plugin code has shown where the problem is.  I
know gstreamer can be very complex, but it's very possible to analyse
the cause of problems and pin them down with detailed logs in conjunction
with the source code.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 19, 2017 at 02:21:10PM +0000, Russell King - ARM Linux wrote:
> There's a good reason why I dumped a full debug log using GST_DEBUG=*:9,
> analysed it for the cause of the failure, and tried several different
> pipelines, including the standard bayer2rgb plugin.
> 
> Please don't blame this on random stuff after analysis of the logs _and_
> reading the appropriate plugin code has shown where the problem is.  I
> know gstreamer can be very complex, but it's very possible to analyse
> the cause of problems and pin them down with detailed logs in conjunction
> with the source code.

Oh, and the proof of correct analysis is that fixing the kernel capture
driver to enumerate the frame sizes and intervals fixes the issue, even
with bayer2rgbneon being used.

Therefore, there is _no way_ what so ever that it could be caused by that
plugin.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 19, 2017 at 02:21:10PM +0000, Russell King - ARM Linux wrote:
> There's a good reason why I dumped a full debug log using GST_DEBUG=*:9,
> analysed it for the cause of the failure, and tried several different
> pipelines, including the standard bayer2rgb plugin.
> 
> Please don't blame this on random stuff after analysis of the logs _and_
> reading the appropriate plugin code has shown where the problem is.  I
> know gstreamer can be very complex, but it's very possible to analyse
> the cause of problems and pin them down with detailed logs in conjunction
> with the source code.

Oh, and the proof of correct analysis is that fixing the kernel capture
driver to enumerate the frame sizes and intervals fixes the issue, even
with bayer2rgbneon being used.

Therefore, there is _no way_ what so ever that it could be caused by that
plugin.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 19, 2017 at 02:21:10PM +0000, Russell King - ARM Linux wrote:
> There's a good reason why I dumped a full debug log using GST_DEBUG=*:9,
> analysed it for the cause of the failure, and tried several different
> pipelines, including the standard bayer2rgb plugin.
> 
> Please don't blame this on random stuff after analysis of the logs _and_
> reading the appropriate plugin code has shown where the problem is.  I
> know gstreamer can be very complex, but it's very possible to analyse
> the cause of problems and pin them down with detailed logs in conjunction
> with the source code.

Oh, and the proof of correct analysis is that fixing the kernel capture
driver to enumerate the frame sizes and intervals fixes the issue, even
with bayer2rgbneon being used.

Therefore, there is _no way_ what so ever that it could be caused by that
plugin.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Vladimir Zapolskiy]

On 03/19/2017 04:22 PM, Russell King - ARM Linux wrote:
> On Sun, Mar 19, 2017 at 02:21:10PM +0000, Russell King - ARM Linux wrote:
>> There's a good reason why I dumped a full debug log using GST_DEBUG=*:9,
>> analysed it for the cause of the failure, and tried several different
>> pipelines, including the standard bayer2rgb plugin.
>>
>> Please don't blame this on random stuff after analysis of the logs _and_
>> reading the appropriate plugin code has shown where the problem is.  I
>> know gstreamer can be very complex, but it's very possible to analyse
>> the cause of problems and pin them down with detailed logs in conjunction
>> with the source code.
> 
> Oh, and the proof of correct analysis is that fixing the kernel capture
> driver to enumerate the frame sizes and intervals fixes the issue, even
> with bayer2rgbneon being used.
> 
> Therefore, there is _no way_ what so ever that it could be caused by that
> plugin.
> 

Hey, no blaming of the unknown to me bayer2rgbneon element from my side,
I've just asked an innocent question, thanks for reply. I failed to find
the source code of the plugin, I was interested to compare its performance
and features with mine in-house NEON powered RGGB/BGGR to RGB24 GStreamer
conversion element, which is written years ago. My question was offtopic.

--
With best wishes,
Vladimir

[PATCH v5 00/39] i.MX Media Driver

[Vladimir Zapolskiy]

On 03/19/2017 04:22 PM, Russell King - ARM Linux wrote:
> On Sun, Mar 19, 2017 at 02:21:10PM +0000, Russell King - ARM Linux wrote:
>> There's a good reason why I dumped a full debug log using GST_DEBUG=*:9,
>> analysed it for the cause of the failure, and tried several different
>> pipelines, including the standard bayer2rgb plugin.
>>
>> Please don't blame this on random stuff after analysis of the logs _and_
>> reading the appropriate plugin code has shown where the problem is.  I
>> know gstreamer can be very complex, but it's very possible to analyse
>> the cause of problems and pin them down with detailed logs in conjunction
>> with the source code.
> 
> Oh, and the proof of correct analysis is that fixing the kernel capture
> driver to enumerate the frame sizes and intervals fixes the issue, even
> with bayer2rgbneon being used.
> 
> Therefore, there is _no way_ what so ever that it could be caused by that
> plugin.
> 

Hey, no blaming of the unknown to me bayer2rgbneon element from my side,
I've just asked an innocent question, thanks for reply. I failed to find
the source code of the plugin, I was interested to compare its performance
and features with mine in-house NEON powered RGGB/BGGR to RGB24 GStreamer
conversion element, which is written years ago. My question was offtopic.

--
With best wishes,
Vladimir

Re: [PATCH v5 00/39] i.MX Media Driver

[Vladimir Zapolskiy]

On 03/19/2017 04:22 PM, Russell King - ARM Linux wrote:
> On Sun, Mar 19, 2017 at 02:21:10PM +0000, Russell King - ARM Linux wrote:
>> There's a good reason why I dumped a full debug log using GST_DEBUG=*:9,
>> analysed it for the cause of the failure, and tried several different
>> pipelines, including the standard bayer2rgb plugin.
>>
>> Please don't blame this on random stuff after analysis of the logs _and_
>> reading the appropriate plugin code has shown where the problem is.  I
>> know gstreamer can be very complex, but it's very possible to analyse
>> the cause of problems and pin them down with detailed logs in conjunction
>> with the source code.
> 
> Oh, and the proof of correct analysis is that fixing the kernel capture
> driver to enumerate the frame sizes and intervals fixes the issue, even
> with bayer2rgbneon being used.
> 
> Therefore, there is _no way_ what so ever that it could be caused by that
> plugin.
> 

Hey, no blaming of the unknown to me bayer2rgbneon element from my side,
I've just asked an innocent question, thanks for reply. I failed to find
the source code of the plugin, I was interested to compare its performance
and features with mine in-house NEON powered RGGB/BGGR to RGB24 GStreamer
conversion element, which is written years ago. My question was offtopic.

--
With best wishes,
Vladimir

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 19, 2017 at 05:00:08PM +0200, Vladimir Zapolskiy wrote:
> On 03/19/2017 04:22 PM, Russell King - ARM Linux wrote:
> > On Sun, Mar 19, 2017 at 02:21:10PM +0000, Russell King - ARM Linux wrote:
> >> There's a good reason why I dumped a full debug log using GST_DEBUG=*:9,
> >> analysed it for the cause of the failure, and tried several different
> >> pipelines, including the standard bayer2rgb plugin.
> >>
> >> Please don't blame this on random stuff after analysis of the logs _and_
> >> reading the appropriate plugin code has shown where the problem is.  I
> >> know gstreamer can be very complex, but it's very possible to analyse
> >> the cause of problems and pin them down with detailed logs in conjunction
> >> with the source code.
> > 
> > Oh, and the proof of correct analysis is that fixing the kernel capture
> > driver to enumerate the frame sizes and intervals fixes the issue, even
> > with bayer2rgbneon being used.
> > 
> > Therefore, there is _no way_ what so ever that it could be caused by that
> > plugin.
> > 
> 
> Hey, no blaming of the unknown to me bayer2rgbneon element from my side,
> I've just asked an innocent question, thanks for reply. I failed to find
> the source code of the plugin, I was interested to compare its performance
> and features with mine in-house NEON powered RGGB/BGGR to RGB24 GStreamer
> conversion element, which is written years ago. My question was offtopic.

If you wanted to know where to get it from, you should've asked that.
You can find all the bits here:

	https://git.phytec.de/

You need bayer2rgb-neon and gst-bayer2rgb-neon, and it requires some
fixes to the configure script and Makefiles get it to build if you
don't have gengenopt available.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 19, 2017 at 05:00:08PM +0200, Vladimir Zapolskiy wrote:
> On 03/19/2017 04:22 PM, Russell King - ARM Linux wrote:
> > On Sun, Mar 19, 2017 at 02:21:10PM +0000, Russell King - ARM Linux wrote:
> >> There's a good reason why I dumped a full debug log using GST_DEBUG=*:9,
> >> analysed it for the cause of the failure, and tried several different
> >> pipelines, including the standard bayer2rgb plugin.
> >>
> >> Please don't blame this on random stuff after analysis of the logs _and_
> >> reading the appropriate plugin code has shown where the problem is.  I
> >> know gstreamer can be very complex, but it's very possible to analyse
> >> the cause of problems and pin them down with detailed logs in conjunction
> >> with the source code.
> > 
> > Oh, and the proof of correct analysis is that fixing the kernel capture
> > driver to enumerate the frame sizes and intervals fixes the issue, even
> > with bayer2rgbneon being used.
> > 
> > Therefore, there is _no way_ what so ever that it could be caused by that
> > plugin.
> > 
> 
> Hey, no blaming of the unknown to me bayer2rgbneon element from my side,
> I've just asked an innocent question, thanks for reply. I failed to find
> the source code of the plugin, I was interested to compare its performance
> and features with mine in-house NEON powered RGGB/BGGR to RGB24 GStreamer
> conversion element, which is written years ago. My question was offtopic.

If you wanted to know where to get it from, you should've asked that.
You can find all the bits here:

	https://git.phytec.de/

You need bayer2rgb-neon and gst-bayer2rgb-neon, and it requires some
fixes to the configure script and Makefiles get it to build if you
don't have gengenopt available.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 19, 2017 at 05:00:08PM +0200, Vladimir Zapolskiy wrote:
> On 03/19/2017 04:22 PM, Russell King - ARM Linux wrote:
> > On Sun, Mar 19, 2017 at 02:21:10PM +0000, Russell King - ARM Linux wrote:
> >> There's a good reason why I dumped a full debug log using GST_DEBUG=*:9,
> >> analysed it for the cause of the failure, and tried several different
> >> pipelines, including the standard bayer2rgb plugin.
> >>
> >> Please don't blame this on random stuff after analysis of the logs _and_
> >> reading the appropriate plugin code has shown where the problem is.  I
> >> know gstreamer can be very complex, but it's very possible to analyse
> >> the cause of problems and pin them down with detailed logs in conjunction
> >> with the source code.
> > 
> > Oh, and the proof of correct analysis is that fixing the kernel capture
> > driver to enumerate the frame sizes and intervals fixes the issue, even
> > with bayer2rgbneon being used.
> > 
> > Therefore, there is _no way_ what so ever that it could be caused by that
> > plugin.
> > 
> 
> Hey, no blaming of the unknown to me bayer2rgbneon element from my side,
> I've just asked an innocent question, thanks for reply. I failed to find
> the source code of the plugin, I was interested to compare its performance
> and features with mine in-house NEON powered RGGB/BGGR to RGB24 GStreamer
> conversion element, which is written years ago. My question was offtopic.

If you wanted to know where to get it from, you should've asked that.
You can find all the bits here:

	https://git.phytec.de/

You need bayer2rgb-neon and gst-bayer2rgb-neon, and it requires some
fixes to the configure script and Makefiles get it to build if you
don't have gengenopt available.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Nicolas Dufresne]

[-- Attachment #1: Type: text/plain, Size: 738 bytes --]

Le dimanche 19 mars 2017 à 14:21 +0000, Russell King - ARM Linux a
écrit :
> > Can it be a point of failure?
> 
> There's a good reason why I dumped a full debug log using
> GST_DEBUG=*:9,
> analysed it for the cause of the failure, and tried several different
> pipelines, including the standard bayer2rgb plugin.
> 
> Please don't blame this on random stuff after analysis of the logs
> _and_
> reading the appropriate plugin code has shown where the problem is. 
> I
> know gstreamer can be very complex, but it's very possible to analyse
> the cause of problems and pin them down with detailed logs in
> conjunction
> with the source code.

I read your analyses with GStreamer, and it was all correct.

Nicolas

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

[PATCH v5 00/39] i.MX Media Driver

[Nicolas Dufresne]

Le dimanche 19 mars 2017 ? 14:21 +0000, Russell King - ARM Linux a
?crit?:
> > Can it be a point of failure?
> 
> There's a good reason why I dumped a full debug log using
> GST_DEBUG=*:9,
> analysed it for the cause of the failure, and tried several different
> pipelines, including the standard bayer2rgb plugin.
> 
> Please don't blame this on random stuff after analysis of the logs
> _and_
> reading the appropriate plugin code has shown where the problem is.?
> I
> know gstreamer can be very complex, but it's very possible to analyse
> the cause of problems and pin them down with detailed logs in
> conjunction
> with the source code.

I read your analyses with GStreamer, and it was all correct.

Nicolas
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 181 bytes
Desc: This is a digitally signed message part
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170319/03da2d8c/attachment.sig>

Re: [PATCH v5 00/39] i.MX Media Driver

[Nicolas Dufresne]

[-- Attachment #1: Type: text/plain, Size: 738 bytes --]

Le dimanche 19 mars 2017 à 14:21 +0000, Russell King - ARM Linux a
écrit :
> > Can it be a point of failure?
> 
> There's a good reason why I dumped a full debug log using
> GST_DEBUG=*:9,
> analysed it for the cause of the failure, and tried several different
> pipelines, including the standard bayer2rgb plugin.
> 
> Please don't blame this on random stuff after analysis of the logs
> _and_
> reading the appropriate plugin code has shown where the problem is. 
> I
> know gstreamer can be very complex, but it's very possible to analyse
> the cause of problems and pin them down with detailed logs in
> conjunction
> with the source code.

I read your analyses with GStreamer, and it was all correct.

Nicolas

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> Right, imx-media-capture.c (the "standard" v4l2 user interface module)
> is not implementing VIDIOC_ENUM_FRAMESIZES. It should, but it can only
> return the single frame size that the pipeline has configured (the mbus
> format of the attached source pad).

I now have a set of patches that enumerate the frame sizes and intervals
from the source pad of the first subdev (since you're setting the formats
etc there from the capture device, it seems sensible to return what it
can support.)  This means my patch set doesn't add to non-CSI subdevs.

> Can you share your gstreamer pipeline? For now, until
> VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
> does not attempt to specify a frame rate. I use the attached
> script for testing, which works for me.

Note that I'm not specifying a frame rate on gstreamer - I'm setting
the pipeline up for 60fps, but gstreamer in its wisdom is unable to
enumerate the frame sizes, and therefore is unable to enumerate the
frame intervals (frame intervals depend on frame sizes), so it
falls back to the "tvnorms" which are basically 25/1 and 30000/1001.

It sees 60fps via G_PARM, and then decides to set 30000/1001 via S_PARM.
So, we end up with most of the pipeline operating at 60fps, with CSI
doing frame skipping to reduce the frame rate to 30fps.

gstreamer doesn't complain, doesn't issue any warnings, the only way
you can spot this is to enable debugging and look through the copious
debug log, or use -v and check the pad capabilities.

Testing using gstreamer, and only using "does it produce video" is a
good simple test, but it's just that - it's a simple test.  It doesn't
tell you that what you're seeing is what you intended to see (such as
video at the frame rate you expected) without more work.

> Thanks, I've fixed most of v4l2-compliance issues, but this is not
> done yet. Is that something you can help with?

What did you do with:

ioctl(3, VIDIOC_REQBUFS, {count=0, type=0 /* V4L2_BUF_TYPE_??? */, memory=0 /* V4L2_MEMORY_??? */}) = -1 EINVAL (Invalid argument)
                test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
ioctl(3, VIDIOC_EXPBUF, 0xbef405bc)     = -1 EINVAL (Invalid argument)
                fail: v4l2-test-buffers.cpp(571): q.has_expbuf(node)
                test VIDIOC_EXPBUF: FAIL

To me, this looks like a bug in v4l2-compliance (I'm using 1.10.0).
I'm not sure what buffer VIDIOC_EXPBUF is expected to export, since
afaics no buffers have been allocated, so of course it's going to fail.
Either that, or the v4l2 core vb2 code is non-compliant with v4l2's
interface requirements.

In any case, it doesn't look like the buffer management is being
tested at all by v4l2-compliance - we know that gstreamer works, so
buffers _can_ be allocated, and I've also used dmabufs with gstreamer,
so I also know that VIDIOC_EXPBUF works there.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> Right, imx-media-capture.c (the "standard" v4l2 user interface module)
> is not implementing VIDIOC_ENUM_FRAMESIZES. It should, but it can only
> return the single frame size that the pipeline has configured (the mbus
> format of the attached source pad).

I now have a set of patches that enumerate the frame sizes and intervals
from the source pad of the first subdev (since you're setting the formats
etc there from the capture device, it seems sensible to return what it
can support.)  This means my patch set doesn't add to non-CSI subdevs.

> Can you share your gstreamer pipeline? For now, until
> VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
> does not attempt to specify a frame rate. I use the attached
> script for testing, which works for me.

Note that I'm not specifying a frame rate on gstreamer - I'm setting
the pipeline up for 60fps, but gstreamer in its wisdom is unable to
enumerate the frame sizes, and therefore is unable to enumerate the
frame intervals (frame intervals depend on frame sizes), so it
falls back to the "tvnorms" which are basically 25/1 and 30000/1001.

It sees 60fps via G_PARM, and then decides to set 30000/1001 via S_PARM.
So, we end up with most of the pipeline operating at 60fps, with CSI
doing frame skipping to reduce the frame rate to 30fps.

gstreamer doesn't complain, doesn't issue any warnings, the only way
you can spot this is to enable debugging and look through the copious
debug log, or use -v and check the pad capabilities.

Testing using gstreamer, and only using "does it produce video" is a
good simple test, but it's just that - it's a simple test.  It doesn't
tell you that what you're seeing is what you intended to see (such as
video at the frame rate you expected) without more work.

> Thanks, I've fixed most of v4l2-compliance issues, but this is not
> done yet. Is that something you can help with?

What did you do with:

ioctl(3, VIDIOC_REQBUFS, {count=0, type=0 /* V4L2_BUF_TYPE_??? */, memory=0 /* V4L2_MEMORY_??? */}) = -1 EINVAL (Invalid argument)
                test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
ioctl(3, VIDIOC_EXPBUF, 0xbef405bc)     = -1 EINVAL (Invalid argument)
                fail: v4l2-test-buffers.cpp(571): q.has_expbuf(node)
                test VIDIOC_EXPBUF: FAIL

To me, this looks like a bug in v4l2-compliance (I'm using 1.10.0).
I'm not sure what buffer VIDIOC_EXPBUF is expected to export, since
afaics no buffers have been allocated, so of course it's going to fail.
Either that, or the v4l2 core vb2 code is non-compliant with v4l2's
interface requirements.

In any case, it doesn't look like the buffer management is being
tested at all by v4l2-compliance - we know that gstreamer works, so
buffers _can_ be allocated, and I've also used dmabufs with gstreamer,
so I also know that VIDIOC_EXPBUF works there.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> Right, imx-media-capture.c (the "standard" v4l2 user interface module)
> is not implementing VIDIOC_ENUM_FRAMESIZES. It should, but it can only
> return the single frame size that the pipeline has configured (the mbus
> format of the attached source pad).

I now have a set of patches that enumerate the frame sizes and intervals
from the source pad of the first subdev (since you're setting the formats
etc there from the capture device, it seems sensible to return what it
can support.)  This means my patch set doesn't add to non-CSI subdevs.

> Can you share your gstreamer pipeline? For now, until
> VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
> does not attempt to specify a frame rate. I use the attached
> script for testing, which works for me.

Note that I'm not specifying a frame rate on gstreamer - I'm setting
the pipeline up for 60fps, but gstreamer in its wisdom is unable to
enumerate the frame sizes, and therefore is unable to enumerate the
frame intervals (frame intervals depend on frame sizes), so it
falls back to the "tvnorms" which are basically 25/1 and 30000/1001.

It sees 60fps via G_PARM, and then decides to set 30000/1001 via S_PARM.
So, we end up with most of the pipeline operating at 60fps, with CSI
doing frame skipping to reduce the frame rate to 30fps.

gstreamer doesn't complain, doesn't issue any warnings, the only way
you can spot this is to enable debugging and look through the copious
debug log, or use -v and check the pad capabilities.

Testing using gstreamer, and only using "does it produce video" is a
good simple test, but it's just that - it's a simple test.  It doesn't
tell you that what you're seeing is what you intended to see (such as
video at the frame rate you expected) without more work.

> Thanks, I've fixed most of v4l2-compliance issues, but this is not
> done yet. Is that something you can help with?

What did you do with:

ioctl(3, VIDIOC_REQBUFS, {count=0, type=0 /* V4L2_BUF_TYPE_??? */, memory=0 /* V4L2_MEMORY_??? */}) = -1 EINVAL (Invalid argument)
                test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
ioctl(3, VIDIOC_EXPBUF, 0xbef405bc)     = -1 EINVAL (Invalid argument)
                fail: v4l2-test-buffers.cpp(571): q.has_expbuf(node)
                test VIDIOC_EXPBUF: FAIL

To me, this looks like a bug in v4l2-compliance (I'm using 1.10.0).
I'm not sure what buffer VIDIOC_EXPBUF is expected to export, since
afaics no buffers have been allocated, so of course it's going to fail.
Either that, or the v4l2 core vb2 code is non-compliant with v4l2's
interface requirements.

In any case, it doesn't look like the buffer management is being
tested at all by v4l2-compliance - we know that gstreamer works, so
buffers _can_ be allocated, and I've also used dmabufs with gstreamer,
so I also know that VIDIOC_EXPBUF works there.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH 1/4] media: imx-media-csi: fix v4l2-compliance check

[Russell King]

v4l2-compliance was failing with:

                fail: v4l2-test-formats.cpp(1076): cap->timeperframe.numerator == 0 || cap->timeperframe.denominator == 0
                test VIDIOC_G/S_PARM: FAIL

Fix this.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 drivers/staging/media/imx/imx-media-csi.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index 0336891069dc..65346e789dd6 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -680,8 +680,10 @@ static const struct csi_skip_desc *csi_find_best_skip(struct v4l2_fract *in,
 
 	/* Default to 1:1 ratio */
 	if (out->numerator == 0 || out->denominator == 0 ||
-	    in->numerator == 0 || in->denominator == 0)
+	    in->numerator == 0 || in->denominator == 0) {
+		*out = *in;
 		return best_skip;
+	}
 
 	want_us = div_u64((u64)USEC_PER_SEC * out->numerator, out->denominator);
 
-- 
2.7.4

[PATCH 1/4] media: imx-media-csi: fix v4l2-compliance check

[Russell King]

v4l2-compliance was failing with:

                fail: v4l2-test-formats.cpp(1076): cap->timeperframe.numerator == 0 || cap->timeperframe.denominator == 0
                test VIDIOC_G/S_PARM: FAIL

Fix this.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 drivers/staging/media/imx/imx-media-csi.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index 0336891069dc..65346e789dd6 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -680,8 +680,10 @@ static const struct csi_skip_desc *csi_find_best_skip(struct v4l2_fract *in,
 
 	/* Default to 1:1 ratio */
 	if (out->numerator == 0 || out->denominator == 0 ||
-	    in->numerator == 0 || in->denominator == 0)
+	    in->numerator == 0 || in->denominator == 0) {
+		*out = *in;
 		return best_skip;
+	}
 
 	want_us = div_u64((u64)USEC_PER_SEC * out->numerator, out->denominator);
 
-- 
2.7.4

Re: [PATCH 1/4] media: imx-media-csi: fix v4l2-compliance check

[Steve Longerbeam]

Looks good to me.

Steve


On 03/19/2017 03:48 AM, Russell King wrote:
> v4l2-compliance was failing with:
>
>                  fail: v4l2-test-formats.cpp(1076): cap->timeperframe.numerator == 0 || cap->timeperframe.denominator == 0
>                  test VIDIOC_G/S_PARM: FAIL
>
> Fix this.
>
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> ---
>   drivers/staging/media/imx/imx-media-csi.c | 4 +++-
>   1 file changed, 3 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
> index 0336891069dc..65346e789dd6 100644
> --- a/drivers/staging/media/imx/imx-media-csi.c
> +++ b/drivers/staging/media/imx/imx-media-csi.c
> @@ -680,8 +680,10 @@ static const struct csi_skip_desc *csi_find_best_skip(struct v4l2_fract *in,
>   
>   	/* Default to 1:1 ratio */
>   	if (out->numerator == 0 || out->denominator == 0 ||
> -	    in->numerator == 0 || in->denominator == 0)
> +	    in->numerator == 0 || in->denominator == 0) {
> +		*out = *in;
>   		return best_skip;
> +	}
>   
>   	want_us = div_u64((u64)USEC_PER_SEC * out->numerator, out->denominator);
>   

[PATCH 1/4] media: imx-media-csi: fix v4l2-compliance check

[Steve Longerbeam]

Looks good to me.

Steve


On 03/19/2017 03:48 AM, Russell King wrote:
> v4l2-compliance was failing with:
>
>                  fail: v4l2-test-formats.cpp(1076): cap->timeperframe.numerator == 0 || cap->timeperframe.denominator == 0
>                  test VIDIOC_G/S_PARM: FAIL
>
> Fix this.
>
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> ---
>   drivers/staging/media/imx/imx-media-csi.c | 4 +++-
>   1 file changed, 3 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
> index 0336891069dc..65346e789dd6 100644
> --- a/drivers/staging/media/imx/imx-media-csi.c
> +++ b/drivers/staging/media/imx/imx-media-csi.c
> @@ -680,8 +680,10 @@ static const struct csi_skip_desc *csi_find_best_skip(struct v4l2_fract *in,
>   
>   	/* Default to 1:1 ratio */
>   	if (out->numerator == 0 || out->denominator == 0 ||
> -	    in->numerator == 0 || in->denominator == 0)
> +	    in->numerator == 0 || in->denominator == 0) {
> +		*out = *in;
>   		return best_skip;
> +	}
>   
>   	want_us = div_u64((u64)USEC_PER_SEC * out->numerator, out->denominator);
>   

[PATCH 2/4] media: imx: allow bayer pixel formats to be looked up

[Russell King]

Allow imx_media_find_format() to look up bayer formats, which is
required to support frame size and interval enumeration.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 drivers/staging/media/imx/imx-media-capture.c | 11 ++++++-----
 drivers/staging/media/imx/imx-media-utils.c   |  6 +++---
 drivers/staging/media/imx/imx-media.h         |  2 +-
 3 files changed, 10 insertions(+), 9 deletions(-)

diff --git a/drivers/staging/media/imx/imx-media-capture.c b/drivers/staging/media/imx/imx-media-capture.c
index ee914396080f..cdeb2cd8b1d7 100644
--- a/drivers/staging/media/imx/imx-media-capture.c
+++ b/drivers/staging/media/imx/imx-media-capture.c
@@ -164,10 +164,10 @@ static int capture_try_fmt_vid_cap(struct file *file, void *fh,
 			CS_SEL_YUV : CS_SEL_RGB;
 		fourcc = f->fmt.pix.pixelformat;
 
-		cc = imx_media_find_format(fourcc, cs_sel);
+		cc = imx_media_find_format(fourcc, cs_sel, false);
 		if (!cc) {
 			imx_media_enum_format(&fourcc, 0, cs_sel);
-			cc = imx_media_find_format(fourcc, cs_sel);
+			cc = imx_media_find_format(fourcc, cs_sel, false);
 		}
 	}
 
@@ -193,7 +193,7 @@ static int capture_s_fmt_vid_cap(struct file *file, void *fh,
 
 	priv->vdev.fmt.fmt.pix = f->fmt.pix;
 	priv->vdev.cc = imx_media_find_format(f->fmt.pix.pixelformat,
-					      CS_SEL_ANY);
+					      CS_SEL_ANY, false);
 
 	return 0;
 }
@@ -505,7 +505,8 @@ void imx_media_capture_device_set_format(struct imx_media_video_dev *vdev,
 
 	mutex_lock(&priv->mutex);
 	priv->vdev.fmt.fmt.pix = *pix;
-	priv->vdev.cc = imx_media_find_format(pix->pixelformat, CS_SEL_ANY);
+	priv->vdev.cc = imx_media_find_format(pix->pixelformat, CS_SEL_ANY,
+					      false);
 	mutex_unlock(&priv->mutex);
 }
 EXPORT_SYMBOL_GPL(imx_media_capture_device_set_format);
@@ -614,7 +615,7 @@ int imx_media_capture_device_register(struct imx_media_video_dev *vdev)
 	imx_media_mbus_fmt_to_pix_fmt(&vdev->fmt.fmt.pix,
 				      &fmt_src.format, NULL);
 	vdev->cc = imx_media_find_format(vdev->fmt.fmt.pix.pixelformat,
-					 CS_SEL_ANY);
+					 CS_SEL_ANY, false);
 
 	v4l2_info(sd, "Registered %s as /dev/%s\n", vfd->name,
 		  video_device_node_name(vfd));
diff --git a/drivers/staging/media/imx/imx-media-utils.c b/drivers/staging/media/imx/imx-media-utils.c
index 6eb7e3c5279e..d048e4a080d0 100644
--- a/drivers/staging/media/imx/imx-media-utils.c
+++ b/drivers/staging/media/imx/imx-media-utils.c
@@ -329,9 +329,9 @@ static int enum_format(u32 *fourcc, u32 *code, u32 index,
 }
 
 const struct imx_media_pixfmt *
-imx_media_find_format(u32 fourcc, enum codespace_sel cs_sel)
+imx_media_find_format(u32 fourcc, enum codespace_sel cs_sel, bool allow_bayer)
 {
-	return find_format(fourcc, 0, cs_sel, true, false);
+	return find_format(fourcc, 0, cs_sel, true, allow_bayer);
 }
 EXPORT_SYMBOL_GPL(imx_media_find_format);
 
@@ -524,7 +524,7 @@ int imx_media_ipu_image_to_mbus_fmt(struct v4l2_mbus_framefmt *mbus,
 {
 	const struct imx_media_pixfmt *fmt;
 
-	fmt = imx_media_find_format(image->pix.pixelformat, CS_SEL_ANY);
+	fmt = imx_media_find_format(image->pix.pixelformat, CS_SEL_ANY, false);
 	if (!fmt)
 		return -EINVAL;
 
diff --git a/drivers/staging/media/imx/imx-media.h b/drivers/staging/media/imx/imx-media.h
index 234242271a13..d8c9536bf1f8 100644
--- a/drivers/staging/media/imx/imx-media.h
+++ b/drivers/staging/media/imx/imx-media.h
@@ -178,7 +178,7 @@ enum codespace_sel {
 };
 
 const struct imx_media_pixfmt *
-imx_media_find_format(u32 fourcc, enum codespace_sel cs_sel);
+imx_media_find_format(u32 fourcc, enum codespace_sel cs_sel, bool allow_bayer);
 int imx_media_enum_format(u32 *fourcc, u32 index, enum codespace_sel cs_sel);
 const struct imx_media_pixfmt *
 imx_media_find_mbus_format(u32 code, enum codespace_sel cs_sel,
-- 
2.7.4

[PATCH 2/4] media: imx: allow bayer pixel formats to be looked up

[Russell King]

Allow imx_media_find_format() to look up bayer formats, which is
required to support frame size and interval enumeration.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 drivers/staging/media/imx/imx-media-capture.c | 11 ++++++-----
 drivers/staging/media/imx/imx-media-utils.c   |  6 +++---
 drivers/staging/media/imx/imx-media.h         |  2 +-
 3 files changed, 10 insertions(+), 9 deletions(-)

diff --git a/drivers/staging/media/imx/imx-media-capture.c b/drivers/staging/media/imx/imx-media-capture.c
index ee914396080f..cdeb2cd8b1d7 100644
--- a/drivers/staging/media/imx/imx-media-capture.c
+++ b/drivers/staging/media/imx/imx-media-capture.c
@@ -164,10 +164,10 @@ static int capture_try_fmt_vid_cap(struct file *file, void *fh,
 			CS_SEL_YUV : CS_SEL_RGB;
 		fourcc = f->fmt.pix.pixelformat;
 
-		cc = imx_media_find_format(fourcc, cs_sel);
+		cc = imx_media_find_format(fourcc, cs_sel, false);
 		if (!cc) {
 			imx_media_enum_format(&fourcc, 0, cs_sel);
-			cc = imx_media_find_format(fourcc, cs_sel);
+			cc = imx_media_find_format(fourcc, cs_sel, false);
 		}
 	}
 
@@ -193,7 +193,7 @@ static int capture_s_fmt_vid_cap(struct file *file, void *fh,
 
 	priv->vdev.fmt.fmt.pix = f->fmt.pix;
 	priv->vdev.cc = imx_media_find_format(f->fmt.pix.pixelformat,
-					      CS_SEL_ANY);
+					      CS_SEL_ANY, false);
 
 	return 0;
 }
@@ -505,7 +505,8 @@ void imx_media_capture_device_set_format(struct imx_media_video_dev *vdev,
 
 	mutex_lock(&priv->mutex);
 	priv->vdev.fmt.fmt.pix = *pix;
-	priv->vdev.cc = imx_media_find_format(pix->pixelformat, CS_SEL_ANY);
+	priv->vdev.cc = imx_media_find_format(pix->pixelformat, CS_SEL_ANY,
+					      false);
 	mutex_unlock(&priv->mutex);
 }
 EXPORT_SYMBOL_GPL(imx_media_capture_device_set_format);
@@ -614,7 +615,7 @@ int imx_media_capture_device_register(struct imx_media_video_dev *vdev)
 	imx_media_mbus_fmt_to_pix_fmt(&vdev->fmt.fmt.pix,
 				      &fmt_src.format, NULL);
 	vdev->cc = imx_media_find_format(vdev->fmt.fmt.pix.pixelformat,
-					 CS_SEL_ANY);
+					 CS_SEL_ANY, false);
 
 	v4l2_info(sd, "Registered %s as /dev/%s\n", vfd->name,
 		  video_device_node_name(vfd));
diff --git a/drivers/staging/media/imx/imx-media-utils.c b/drivers/staging/media/imx/imx-media-utils.c
index 6eb7e3c5279e..d048e4a080d0 100644
--- a/drivers/staging/media/imx/imx-media-utils.c
+++ b/drivers/staging/media/imx/imx-media-utils.c
@@ -329,9 +329,9 @@ static int enum_format(u32 *fourcc, u32 *code, u32 index,
 }
 
 const struct imx_media_pixfmt *
-imx_media_find_format(u32 fourcc, enum codespace_sel cs_sel)
+imx_media_find_format(u32 fourcc, enum codespace_sel cs_sel, bool allow_bayer)
 {
-	return find_format(fourcc, 0, cs_sel, true, false);
+	return find_format(fourcc, 0, cs_sel, true, allow_bayer);
 }
 EXPORT_SYMBOL_GPL(imx_media_find_format);
 
@@ -524,7 +524,7 @@ int imx_media_ipu_image_to_mbus_fmt(struct v4l2_mbus_framefmt *mbus,
 {
 	const struct imx_media_pixfmt *fmt;
 
-	fmt = imx_media_find_format(image->pix.pixelformat, CS_SEL_ANY);
+	fmt = imx_media_find_format(image->pix.pixelformat, CS_SEL_ANY, false);
 	if (!fmt)
 		return -EINVAL;
 
diff --git a/drivers/staging/media/imx/imx-media.h b/drivers/staging/media/imx/imx-media.h
index 234242271a13..d8c9536bf1f8 100644
--- a/drivers/staging/media/imx/imx-media.h
+++ b/drivers/staging/media/imx/imx-media.h
@@ -178,7 +178,7 @@ enum codespace_sel {
 };
 
 const struct imx_media_pixfmt *
-imx_media_find_format(u32 fourcc, enum codespace_sel cs_sel);
+imx_media_find_format(u32 fourcc, enum codespace_sel cs_sel, bool allow_bayer);
 int imx_media_enum_format(u32 *fourcc, u32 index, enum codespace_sel cs_sel);
 const struct imx_media_pixfmt *
 imx_media_find_mbus_format(u32 code, enum codespace_sel cs_sel,
-- 
2.7.4

Re: [PATCH 2/4] media: imx: allow bayer pixel formats to be looked up

[Steve Longerbeam]

This is good too, but if it's all right with you I would prefer to
squash this with the "redo  pixel format enumeration and
negotiation" patch, to keep the patch count down.

Steve


On 03/19/2017 03:48 AM, Russell King wrote:
> Allow imx_media_find_format() to look up bayer formats, which is
> required to support frame size and interval enumeration.
>
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> ---
>   drivers/staging/media/imx/imx-media-capture.c | 11 ++++++-----
>   drivers/staging/media/imx/imx-media-utils.c   |  6 +++---
>   drivers/staging/media/imx/imx-media.h         |  2 +-
>   3 files changed, 10 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/staging/media/imx/imx-media-capture.c b/drivers/staging/media/imx/imx-media-capture.c
> index ee914396080f..cdeb2cd8b1d7 100644
> --- a/drivers/staging/media/imx/imx-media-capture.c
> +++ b/drivers/staging/media/imx/imx-media-capture.c
> @@ -164,10 +164,10 @@ static int capture_try_fmt_vid_cap(struct file *file, void *fh,
>   			CS_SEL_YUV : CS_SEL_RGB;
>   		fourcc = f->fmt.pix.pixelformat;
>   
> -		cc = imx_media_find_format(fourcc, cs_sel);
> +		cc = imx_media_find_format(fourcc, cs_sel, false);
>   		if (!cc) {
>   			imx_media_enum_format(&fourcc, 0, cs_sel);
> -			cc = imx_media_find_format(fourcc, cs_sel);
> +			cc = imx_media_find_format(fourcc, cs_sel, false);
>   		}
>   	}
>   
> @@ -193,7 +193,7 @@ static int capture_s_fmt_vid_cap(struct file *file, void *fh,
>   
>   	priv->vdev.fmt.fmt.pix = f->fmt.pix;
>   	priv->vdev.cc = imx_media_find_format(f->fmt.pix.pixelformat,
> -					      CS_SEL_ANY);
> +					      CS_SEL_ANY, false);
>   
>   	return 0;
>   }
> @@ -505,7 +505,8 @@ void imx_media_capture_device_set_format(struct imx_media_video_dev *vdev,
>   
>   	mutex_lock(&priv->mutex);
>   	priv->vdev.fmt.fmt.pix = *pix;
> -	priv->vdev.cc = imx_media_find_format(pix->pixelformat, CS_SEL_ANY);
> +	priv->vdev.cc = imx_media_find_format(pix->pixelformat, CS_SEL_ANY,
> +					      false);
>   	mutex_unlock(&priv->mutex);
>   }
>   EXPORT_SYMBOL_GPL(imx_media_capture_device_set_format);
> @@ -614,7 +615,7 @@ int imx_media_capture_device_register(struct imx_media_video_dev *vdev)
>   	imx_media_mbus_fmt_to_pix_fmt(&vdev->fmt.fmt.pix,
>   				      &fmt_src.format, NULL);
>   	vdev->cc = imx_media_find_format(vdev->fmt.fmt.pix.pixelformat,
> -					 CS_SEL_ANY);
> +					 CS_SEL_ANY, false);
>   
>   	v4l2_info(sd, "Registered %s as /dev/%s\n", vfd->name,
>   		  video_device_node_name(vfd));
> diff --git a/drivers/staging/media/imx/imx-media-utils.c b/drivers/staging/media/imx/imx-media-utils.c
> index 6eb7e3c5279e..d048e4a080d0 100644
> --- a/drivers/staging/media/imx/imx-media-utils.c
> +++ b/drivers/staging/media/imx/imx-media-utils.c
> @@ -329,9 +329,9 @@ static int enum_format(u32 *fourcc, u32 *code, u32 index,
>   }
>   
>   const struct imx_media_pixfmt *
> -imx_media_find_format(u32 fourcc, enum codespace_sel cs_sel)
> +imx_media_find_format(u32 fourcc, enum codespace_sel cs_sel, bool allow_bayer)
>   {
> -	return find_format(fourcc, 0, cs_sel, true, false);
> +	return find_format(fourcc, 0, cs_sel, true, allow_bayer);
>   }
>   EXPORT_SYMBOL_GPL(imx_media_find_format);
>   
> @@ -524,7 +524,7 @@ int imx_media_ipu_image_to_mbus_fmt(struct v4l2_mbus_framefmt *mbus,
>   {
>   	const struct imx_media_pixfmt *fmt;
>   
> -	fmt = imx_media_find_format(image->pix.pixelformat, CS_SEL_ANY);
> +	fmt = imx_media_find_format(image->pix.pixelformat, CS_SEL_ANY, false);
>   	if (!fmt)
>   		return -EINVAL;
>   
> diff --git a/drivers/staging/media/imx/imx-media.h b/drivers/staging/media/imx/imx-media.h
> index 234242271a13..d8c9536bf1f8 100644
> --- a/drivers/staging/media/imx/imx-media.h
> +++ b/drivers/staging/media/imx/imx-media.h
> @@ -178,7 +178,7 @@ enum codespace_sel {
>   };
>   
>   const struct imx_media_pixfmt *
> -imx_media_find_format(u32 fourcc, enum codespace_sel cs_sel);
> +imx_media_find_format(u32 fourcc, enum codespace_sel cs_sel, bool allow_bayer);
>   int imx_media_enum_format(u32 *fourcc, u32 index, enum codespace_sel cs_sel);
>   const struct imx_media_pixfmt *
>   imx_media_find_mbus_format(u32 code, enum codespace_sel cs_sel,

[PATCH 2/4] media: imx: allow bayer pixel formats to be looked up

[Steve Longerbeam]

This is good too, but if it's all right with you I would prefer to
squash this with the "redo  pixel format enumeration and
negotiation" patch, to keep the patch count down.

Steve


On 03/19/2017 03:48 AM, Russell King wrote:
> Allow imx_media_find_format() to look up bayer formats, which is
> required to support frame size and interval enumeration.
>
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> ---
>   drivers/staging/media/imx/imx-media-capture.c | 11 ++++++-----
>   drivers/staging/media/imx/imx-media-utils.c   |  6 +++---
>   drivers/staging/media/imx/imx-media.h         |  2 +-
>   3 files changed, 10 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/staging/media/imx/imx-media-capture.c b/drivers/staging/media/imx/imx-media-capture.c
> index ee914396080f..cdeb2cd8b1d7 100644
> --- a/drivers/staging/media/imx/imx-media-capture.c
> +++ b/drivers/staging/media/imx/imx-media-capture.c
> @@ -164,10 +164,10 @@ static int capture_try_fmt_vid_cap(struct file *file, void *fh,
>   			CS_SEL_YUV : CS_SEL_RGB;
>   		fourcc = f->fmt.pix.pixelformat;
>   
> -		cc = imx_media_find_format(fourcc, cs_sel);
> +		cc = imx_media_find_format(fourcc, cs_sel, false);
>   		if (!cc) {
>   			imx_media_enum_format(&fourcc, 0, cs_sel);
> -			cc = imx_media_find_format(fourcc, cs_sel);
> +			cc = imx_media_find_format(fourcc, cs_sel, false);
>   		}
>   	}
>   
> @@ -193,7 +193,7 @@ static int capture_s_fmt_vid_cap(struct file *file, void *fh,
>   
>   	priv->vdev.fmt.fmt.pix = f->fmt.pix;
>   	priv->vdev.cc = imx_media_find_format(f->fmt.pix.pixelformat,
> -					      CS_SEL_ANY);
> +					      CS_SEL_ANY, false);
>   
>   	return 0;
>   }
> @@ -505,7 +505,8 @@ void imx_media_capture_device_set_format(struct imx_media_video_dev *vdev,
>   
>   	mutex_lock(&priv->mutex);
>   	priv->vdev.fmt.fmt.pix = *pix;
> -	priv->vdev.cc = imx_media_find_format(pix->pixelformat, CS_SEL_ANY);
> +	priv->vdev.cc = imx_media_find_format(pix->pixelformat, CS_SEL_ANY,
> +					      false);
>   	mutex_unlock(&priv->mutex);
>   }
>   EXPORT_SYMBOL_GPL(imx_media_capture_device_set_format);
> @@ -614,7 +615,7 @@ int imx_media_capture_device_register(struct imx_media_video_dev *vdev)
>   	imx_media_mbus_fmt_to_pix_fmt(&vdev->fmt.fmt.pix,
>   				      &fmt_src.format, NULL);
>   	vdev->cc = imx_media_find_format(vdev->fmt.fmt.pix.pixelformat,
> -					 CS_SEL_ANY);
> +					 CS_SEL_ANY, false);
>   
>   	v4l2_info(sd, "Registered %s as /dev/%s\n", vfd->name,
>   		  video_device_node_name(vfd));
> diff --git a/drivers/staging/media/imx/imx-media-utils.c b/drivers/staging/media/imx/imx-media-utils.c
> index 6eb7e3c5279e..d048e4a080d0 100644
> --- a/drivers/staging/media/imx/imx-media-utils.c
> +++ b/drivers/staging/media/imx/imx-media-utils.c
> @@ -329,9 +329,9 @@ static int enum_format(u32 *fourcc, u32 *code, u32 index,
>   }
>   
>   const struct imx_media_pixfmt *
> -imx_media_find_format(u32 fourcc, enum codespace_sel cs_sel)
> +imx_media_find_format(u32 fourcc, enum codespace_sel cs_sel, bool allow_bayer)
>   {
> -	return find_format(fourcc, 0, cs_sel, true, false);
> +	return find_format(fourcc, 0, cs_sel, true, allow_bayer);
>   }
>   EXPORT_SYMBOL_GPL(imx_media_find_format);
>   
> @@ -524,7 +524,7 @@ int imx_media_ipu_image_to_mbus_fmt(struct v4l2_mbus_framefmt *mbus,
>   {
>   	const struct imx_media_pixfmt *fmt;
>   
> -	fmt = imx_media_find_format(image->pix.pixelformat, CS_SEL_ANY);
> +	fmt = imx_media_find_format(image->pix.pixelformat, CS_SEL_ANY, false);
>   	if (!fmt)
>   		return -EINVAL;
>   
> diff --git a/drivers/staging/media/imx/imx-media.h b/drivers/staging/media/imx/imx-media.h
> index 234242271a13..d8c9536bf1f8 100644
> --- a/drivers/staging/media/imx/imx-media.h
> +++ b/drivers/staging/media/imx/imx-media.h
> @@ -178,7 +178,7 @@ enum codespace_sel {
>   };
>   
>   const struct imx_media_pixfmt *
> -imx_media_find_format(u32 fourcc, enum codespace_sel cs_sel);
> +imx_media_find_format(u32 fourcc, enum codespace_sel cs_sel, bool allow_bayer);
>   int imx_media_enum_format(u32 *fourcc, u32 index, enum codespace_sel cs_sel);
>   const struct imx_media_pixfmt *
>   imx_media_find_mbus_format(u32 code, enum codespace_sel cs_sel,

[PATCH 3/4] media: imx-csi: add frame size/interval enumeration

[Russell King]

Add frame size and frame interval enumeration to CSI.

CSI can scale the image independently horizontally and vertically by a
factor of two, which enumerates to four different frame sizes.

CSI can also drop frames, resulting in frame rate reduction, so
enumerate the resulting possible output frame rates.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 drivers/staging/media/imx/imx-media-csi.c | 51 +++++++++++++++++++++++++++++++
 1 file changed, 51 insertions(+)

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index 65346e789dd6..d19659d7ddc2 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -1073,6 +1073,55 @@ static int csi_enum_mbus_code(struct v4l2_subdev *sd,
 	return ret;
 }
 
+static int csi_enum_frame_size(struct v4l2_subdev *sd,
+			       struct v4l2_subdev_pad_config *cfg,
+			       struct v4l2_subdev_frame_size_enum *fse)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_mbus_framefmt *fmt;
+	int ret = 0;
+
+	if (fse->pad >= CSI_NUM_PADS ||
+	    fse->index > (fse->pad == CSI_SINK_PAD ? 0 : 3))
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+	fmt = __csi_get_fmt(priv, cfg, fse->pad, fse->which);
+	fse->min_width = fse->max_width = fse->index & 1 ?
+					    fmt->width >> 1 : fmt->width;
+	fse->min_height = fse->max_height = fse->index & 2 ?
+					      fmt->height >> 1 : fmt->height;
+	mutex_unlock(&priv->lock);
+
+	return ret;
+}
+
+static int csi_enum_frame_interval(struct v4l2_subdev *sd,
+				   struct v4l2_subdev_pad_config *cfg,
+				   struct v4l2_subdev_frame_interval_enum *fie)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_mbus_framefmt *fmt;
+	int ret = 0;
+
+	if (fie->pad >= CSI_NUM_PADS ||
+	    fie->index >= (fie->pad == CSI_SINK_PAD ? 1 : ARRAY_SIZE(csi_skip)))
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+	fmt = __csi_get_fmt(priv, cfg, fie->pad, fie->which);
+	if ((fie->width == fmt->width || fie->width == fmt->width / 2) &&
+	    (fie->height == fmt->height || fie->height == fmt->height / 2)) {
+		fie->interval = priv->frame_interval;
+		csi_apply_skip_interval(&csi_skip[fie->index], &fie->interval);
+	} else {
+		ret = -EINVAL;
+	}
+	mutex_unlock(&priv->lock);
+
+	return ret;
+}
+
 static int csi_get_fmt(struct v4l2_subdev *sd,
 		       struct v4l2_subdev_pad_config *cfg,
 		       struct v4l2_subdev_format *sdformat)
@@ -1473,6 +1522,8 @@ static struct v4l2_subdev_video_ops csi_video_ops = {
 
 static struct v4l2_subdev_pad_ops csi_pad_ops = {
 	.enum_mbus_code = csi_enum_mbus_code,
+	.enum_frame_size = csi_enum_frame_size,
+	.enum_frame_interval = csi_enum_frame_interval,
 	.get_fmt = csi_get_fmt,
 	.set_fmt = csi_set_fmt,
 	.get_selection = csi_get_selection,
-- 
2.7.4

[PATCH 3/4] media: imx-csi: add frame size/interval enumeration

[Russell King]

Add frame size and frame interval enumeration to CSI.

CSI can scale the image independently horizontally and vertically by a
factor of two, which enumerates to four different frame sizes.

CSI can also drop frames, resulting in frame rate reduction, so
enumerate the resulting possible output frame rates.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 drivers/staging/media/imx/imx-media-csi.c | 51 +++++++++++++++++++++++++++++++
 1 file changed, 51 insertions(+)

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index 65346e789dd6..d19659d7ddc2 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -1073,6 +1073,55 @@ static int csi_enum_mbus_code(struct v4l2_subdev *sd,
 	return ret;
 }
 
+static int csi_enum_frame_size(struct v4l2_subdev *sd,
+			       struct v4l2_subdev_pad_config *cfg,
+			       struct v4l2_subdev_frame_size_enum *fse)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_mbus_framefmt *fmt;
+	int ret = 0;
+
+	if (fse->pad >= CSI_NUM_PADS ||
+	    fse->index > (fse->pad == CSI_SINK_PAD ? 0 : 3))
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+	fmt = __csi_get_fmt(priv, cfg, fse->pad, fse->which);
+	fse->min_width = fse->max_width = fse->index & 1 ?
+					    fmt->width >> 1 : fmt->width;
+	fse->min_height = fse->max_height = fse->index & 2 ?
+					      fmt->height >> 1 : fmt->height;
+	mutex_unlock(&priv->lock);
+
+	return ret;
+}
+
+static int csi_enum_frame_interval(struct v4l2_subdev *sd,
+				   struct v4l2_subdev_pad_config *cfg,
+				   struct v4l2_subdev_frame_interval_enum *fie)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_mbus_framefmt *fmt;
+	int ret = 0;
+
+	if (fie->pad >= CSI_NUM_PADS ||
+	    fie->index >= (fie->pad == CSI_SINK_PAD ? 1 : ARRAY_SIZE(csi_skip)))
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+	fmt = __csi_get_fmt(priv, cfg, fie->pad, fie->which);
+	if ((fie->width == fmt->width || fie->width == fmt->width / 2) &&
+	    (fie->height == fmt->height || fie->height == fmt->height / 2)) {
+		fie->interval = priv->frame_interval;
+		csi_apply_skip_interval(&csi_skip[fie->index], &fie->interval);
+	} else {
+		ret = -EINVAL;
+	}
+	mutex_unlock(&priv->lock);
+
+	return ret;
+}
+
 static int csi_get_fmt(struct v4l2_subdev *sd,
 		       struct v4l2_subdev_pad_config *cfg,
 		       struct v4l2_subdev_format *sdformat)
@@ -1473,6 +1522,8 @@ static struct v4l2_subdev_video_ops csi_video_ops = {
 
 static struct v4l2_subdev_pad_ops csi_pad_ops = {
 	.enum_mbus_code = csi_enum_mbus_code,
+	.enum_frame_size = csi_enum_frame_size,
+	.enum_frame_interval = csi_enum_frame_interval,
 	.get_fmt = csi_get_fmt,
 	.set_fmt = csi_set_fmt,
 	.get_selection = csi_get_selection,
-- 
2.7.4

Re: [PATCH 3/4] media: imx-csi: add frame size/interval enumeration

[Steve Longerbeam]

On 03/19/2017 03:49 AM, Russell King wrote:
> Add frame size and frame interval enumeration to CSI.
>
> CSI can scale the image independently horizontally and vertically by a
> factor of two, which enumerates to four different frame sizes.
>
> CSI can also drop frames, resulting in frame rate reduction, so
> enumerate the resulting possible output frame rates.
>
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> ---
>   drivers/staging/media/imx/imx-media-csi.c | 51 +++++++++++++++++++++++++++++++
>   1 file changed, 51 insertions(+)
>
> diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
> index 65346e789dd6..d19659d7ddc2 100644
> --- a/drivers/staging/media/imx/imx-media-csi.c
> +++ b/drivers/staging/media/imx/imx-media-csi.c
> @@ -1073,6 +1073,55 @@ static int csi_enum_mbus_code(struct v4l2_subdev *sd,
>   	return ret;
>   }
>   
> +static int csi_enum_frame_size(struct v4l2_subdev *sd,
> +			       struct v4l2_subdev_pad_config *cfg,
> +			       struct v4l2_subdev_frame_size_enum *fse)
> +{
> +	struct csi_priv *priv = v4l2_get_subdevdata(sd);
> +	struct v4l2_mbus_framefmt *fmt;
> +	int ret = 0;
> +
> +	if (fse->pad >= CSI_NUM_PADS ||
> +	    fse->index > (fse->pad == CSI_SINK_PAD ? 0 : 3))
> +		return -EINVAL;
> +
> +	mutex_lock(&priv->lock);
> +	fmt = __csi_get_fmt(priv, cfg, fse->pad, fse->which);
> +	fse->min_width = fse->max_width = fse->index & 1 ?
> +					    fmt->width >> 1 : fmt->width;
> +	fse->min_height = fse->max_height = fse->index & 2 ?
> +					      fmt->height >> 1 : fmt->height;
> +	mutex_unlock(&priv->lock);
> +
> +	return ret;
> +}

This will only enumerate the currently set/tried format at the sink
pad. But the sink pad supports a range of widths/heights.

I think this function should call csi_try_fmt() at the sink pad.

The other media drivers do the same, they return a supported range at
the sinks rather than only the last set/tried values.

So the sink enumeration should return a continuous range.
The source enumeration should behave the same as you have it above
however, i.e. a discrete set of 4 possibilities since the CSI is limited to
only /2 downsizing in both dimensions.

Steve

> +
> +static int csi_enum_frame_interval(struct v4l2_subdev *sd,
> +				   struct v4l2_subdev_pad_config *cfg,
> +				   struct v4l2_subdev_frame_interval_enum *fie)
> +{
> +	struct csi_priv *priv = v4l2_get_subdevdata(sd);
> +	struct v4l2_mbus_framefmt *fmt;
> +	int ret = 0;
> +
> +	if (fie->pad >= CSI_NUM_PADS ||
> +	    fie->index >= (fie->pad == CSI_SINK_PAD ? 1 : ARRAY_SIZE(csi_skip)))
> +		return -EINVAL;
> +
> +	mutex_lock(&priv->lock);
> +	fmt = __csi_get_fmt(priv, cfg, fie->pad, fie->which);
> +	if ((fie->width == fmt->width || fie->width == fmt->width / 2) &&
> +	    (fie->height == fmt->height || fie->height == fmt->height / 2)) {
> +		fie->interval = priv->frame_interval;
> +		csi_apply_skip_interval(&csi_skip[fie->index], &fie->interval);
> +	} else {
> +		ret = -EINVAL;
> +	}
> +	mutex_unlock(&priv->lock);
> +
> +	return ret;
> +}
> +
>   static int csi_get_fmt(struct v4l2_subdev *sd,
>   		       struct v4l2_subdev_pad_config *cfg,
>   		       struct v4l2_subdev_format *sdformat)
> @@ -1473,6 +1522,8 @@ static struct v4l2_subdev_video_ops csi_video_ops = {
>   
>   static struct v4l2_subdev_pad_ops csi_pad_ops = {
>   	.enum_mbus_code = csi_enum_mbus_code,
> +	.enum_frame_size = csi_enum_frame_size,
> +	.enum_frame_interval = csi_enum_frame_interval,
>   	.get_fmt = csi_get_fmt,
>   	.set_fmt = csi_set_fmt,
>   	.get_selection = csi_get_selection,

[PATCH 3/4] media: imx-csi: add frame size/interval enumeration

[Steve Longerbeam]

On 03/19/2017 03:49 AM, Russell King wrote:
> Add frame size and frame interval enumeration to CSI.
>
> CSI can scale the image independently horizontally and vertically by a
> factor of two, which enumerates to four different frame sizes.
>
> CSI can also drop frames, resulting in frame rate reduction, so
> enumerate the resulting possible output frame rates.
>
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> ---
>   drivers/staging/media/imx/imx-media-csi.c | 51 +++++++++++++++++++++++++++++++
>   1 file changed, 51 insertions(+)
>
> diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
> index 65346e789dd6..d19659d7ddc2 100644
> --- a/drivers/staging/media/imx/imx-media-csi.c
> +++ b/drivers/staging/media/imx/imx-media-csi.c
> @@ -1073,6 +1073,55 @@ static int csi_enum_mbus_code(struct v4l2_subdev *sd,
>   	return ret;
>   }
>   
> +static int csi_enum_frame_size(struct v4l2_subdev *sd,
> +			       struct v4l2_subdev_pad_config *cfg,
> +			       struct v4l2_subdev_frame_size_enum *fse)
> +{
> +	struct csi_priv *priv = v4l2_get_subdevdata(sd);
> +	struct v4l2_mbus_framefmt *fmt;
> +	int ret = 0;
> +
> +	if (fse->pad >= CSI_NUM_PADS ||
> +	    fse->index > (fse->pad == CSI_SINK_PAD ? 0 : 3))
> +		return -EINVAL;
> +
> +	mutex_lock(&priv->lock);
> +	fmt = __csi_get_fmt(priv, cfg, fse->pad, fse->which);
> +	fse->min_width = fse->max_width = fse->index & 1 ?
> +					    fmt->width >> 1 : fmt->width;
> +	fse->min_height = fse->max_height = fse->index & 2 ?
> +					      fmt->height >> 1 : fmt->height;
> +	mutex_unlock(&priv->lock);
> +
> +	return ret;
> +}

This will only enumerate the currently set/tried format at the sink
pad. But the sink pad supports a range of widths/heights.

I think this function should call csi_try_fmt() at the sink pad.

The other media drivers do the same, they return a supported range at
the sinks rather than only the last set/tried values.

So the sink enumeration should return a continuous range.
The source enumeration should behave the same as you have it above
however, i.e. a discrete set of 4 possibilities since the CSI is limited to
only /2 downsizing in both dimensions.

Steve

> +
> +static int csi_enum_frame_interval(struct v4l2_subdev *sd,
> +				   struct v4l2_subdev_pad_config *cfg,
> +				   struct v4l2_subdev_frame_interval_enum *fie)
> +{
> +	struct csi_priv *priv = v4l2_get_subdevdata(sd);
> +	struct v4l2_mbus_framefmt *fmt;
> +	int ret = 0;
> +
> +	if (fie->pad >= CSI_NUM_PADS ||
> +	    fie->index >= (fie->pad == CSI_SINK_PAD ? 1 : ARRAY_SIZE(csi_skip)))
> +		return -EINVAL;
> +
> +	mutex_lock(&priv->lock);
> +	fmt = __csi_get_fmt(priv, cfg, fie->pad, fie->which);
> +	if ((fie->width == fmt->width || fie->width == fmt->width / 2) &&
> +	    (fie->height == fmt->height || fie->height == fmt->height / 2)) {
> +		fie->interval = priv->frame_interval;
> +		csi_apply_skip_interval(&csi_skip[fie->index], &fie->interval);
> +	} else {
> +		ret = -EINVAL;
> +	}
> +	mutex_unlock(&priv->lock);
> +
> +	return ret;
> +}
> +
>   static int csi_get_fmt(struct v4l2_subdev *sd,
>   		       struct v4l2_subdev_pad_config *cfg,
>   		       struct v4l2_subdev_format *sdformat)
> @@ -1473,6 +1522,8 @@ static struct v4l2_subdev_video_ops csi_video_ops = {
>   
>   static struct v4l2_subdev_pad_ops csi_pad_ops = {
>   	.enum_mbus_code = csi_enum_mbus_code,
> +	.enum_frame_size = csi_enum_frame_size,
> +	.enum_frame_interval = csi_enum_frame_interval,
>   	.get_fmt = csi_get_fmt,
>   	.set_fmt = csi_set_fmt,
>   	.get_selection = csi_get_selection,

Re: [PATCH 3/4] media: imx-csi: add frame size/interval enumeration

[Steve Longerbeam]

[-- Attachment #1: Type: text/plain, Size: 721 bytes --]

Hi Russell,

On 03/19/2017 03:49 AM, Russell King wrote:
> Add frame size and frame interval enumeration to CSI.
>
> CSI can scale the image independently horizontally and vertically by a
> factor of two, which enumerates to four different frame sizes.
>
> CSI can also drop frames, resulting in frame rate reduction, so
> enumerate the resulting possible output frame rates.
>

I applied this patch, modified to return a frame size range on the
sink pad. Also, I believe both frame size and frame interval
enumeration should base their decision making on the crop rectangle
at the sink pad, not on the format at the source pads, due to the
crop/compose re-org patch from Philipp.

The updated patch is attached.

Steve


[-- Attachment #2: 0036-media-imx-csi-add-frame-size-interval-enumeration.patch --]
[-- Type: text/x-patch, Size: 3305 bytes --]

>From ce1772dfe9e0381b2749102e760ed7c49fda5ae2 Mon Sep 17 00:00:00 2001
From: Russell King <rmk+kernel@armlinux.org.uk>
Date: Sun, 19 Mar 2017 10:49:02 +0000
Subject: [PATCH 36/38] media: imx-csi: add frame size/interval enumeration

Add frame size and frame interval enumeration to CSI.

CSI can downscale the image independently horizontally and vertically by a
factor of two, which enumerates to four different frame sizes at the
output pads. The input pad supports a range of frame sizes.

CSI can also drop frames, resulting in frame rate reduction, so
enumerate the resulting possible output frame rates.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
 drivers/staging/media/imx/imx-media-csi.c | 62 +++++++++++++++++++++++++++++++
 1 file changed, 62 insertions(+)

diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index 5f9fa83..55265c1 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -1098,6 +1098,66 @@ static int csi_enum_mbus_code(struct v4l2_subdev *sd,
 	return ret;
 }
 
+static int csi_enum_frame_size(struct v4l2_subdev *sd,
+			       struct v4l2_subdev_pad_config *cfg,
+			       struct v4l2_subdev_frame_size_enum *fse)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_rect *crop;
+	int ret = 0;
+
+	if (fse->pad >= CSI_NUM_PADS ||
+	    fse->index > (fse->pad == CSI_SINK_PAD ? 0 : 3))
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	if (fse->pad == CSI_SINK_PAD) {
+		fse->min_width = MIN_W;
+		fse->max_width = MAX_W;
+		fse->min_height = MIN_H;
+		fse->max_height = MAX_H;
+	} else {
+		crop = __csi_get_crop(priv, cfg, fse->which);
+
+		fse->min_width = fse->max_width = fse->index & 1 ?
+			crop->width / 2 : crop->width;
+		fse->min_height = fse->max_height = fse->index & 2 ?
+			crop->height / 2 : crop->height;
+	}
+
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int csi_enum_frame_interval(struct v4l2_subdev *sd,
+				   struct v4l2_subdev_pad_config *cfg,
+				   struct v4l2_subdev_frame_interval_enum *fie)
+{
+	struct csi_priv *priv = v4l2_get_subdevdata(sd);
+	struct v4l2_rect *crop;
+	int ret = 0;
+
+	if (fie->pad >= CSI_NUM_PADS ||
+	    fie->index >= (fie->pad == CSI_SINK_PAD ? 1 : ARRAY_SIZE(csi_skip)))
+		return -EINVAL;
+
+	mutex_lock(&priv->lock);
+
+	crop = __csi_get_crop(priv, cfg, fie->which);
+
+	if ((fie->width == crop->width || fie->width == crop->width / 2) &&
+	    (fie->height == crop->height || fie->height == crop->height / 2)) {
+		fie->interval = priv->frame_interval;
+		csi_apply_skip_interval(&csi_skip[fie->index], &fie->interval);
+	} else {
+		ret = -EINVAL;
+	}
+	mutex_unlock(&priv->lock);
+
+	return ret;
+}
+
 static int csi_get_fmt(struct v4l2_subdev *sd,
 		       struct v4l2_subdev_pad_config *cfg,
 		       struct v4l2_subdev_format *sdformat)
@@ -1562,6 +1622,8 @@ static struct v4l2_subdev_video_ops csi_video_ops = {
 
 static struct v4l2_subdev_pad_ops csi_pad_ops = {
 	.enum_mbus_code = csi_enum_mbus_code,
+	.enum_frame_size = csi_enum_frame_size,
+	.enum_frame_interval = csi_enum_frame_interval,
 	.get_fmt = csi_get_fmt,
 	.set_fmt = csi_set_fmt,
 	.get_selection = csi_get_selection,
-- 
2.7.4

[PATCH 3/4] media: imx-csi: add frame size/interval enumeration

[Steve Longerbeam]

Hi Russell,

On 03/19/2017 03:49 AM, Russell King wrote:
> Add frame size and frame interval enumeration to CSI.
>
> CSI can scale the image independently horizontally and vertically by a
> factor of two, which enumerates to four different frame sizes.
>
> CSI can also drop frames, resulting in frame rate reduction, so
> enumerate the resulting possible output frame rates.
>

I applied this patch, modified to return a frame size range on the
sink pad. Also, I believe both frame size and frame interval
enumeration should base their decision making on the crop rectangle
at the sink pad, not on the format at the source pads, due to the
crop/compose re-org patch from Philipp.

The updated patch is attached.

Steve

-------------- next part --------------
A non-text attachment was scrubbed...
Name: 0036-media-imx-csi-add-frame-size-interval-enumeration.patch
Type: text/x-patch
Size: 3305 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170321/0809b6dc/attachment.bin>

[PATCH 4/4] media: imx-media-capture: add frame sizes/interval enumeration

[Russell King]

Add support for enumerating frame sizes and frame intervals from the
first subdev via the V4L2 interfaces.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 drivers/staging/media/imx/imx-media-capture.c | 62 +++++++++++++++++++++++++++
 1 file changed, 62 insertions(+)

diff --git a/drivers/staging/media/imx/imx-media-capture.c b/drivers/staging/media/imx/imx-media-capture.c
index cdeb2cd8b1d7..bc99d9310e36 100644
--- a/drivers/staging/media/imx/imx-media-capture.c
+++ b/drivers/staging/media/imx/imx-media-capture.c
@@ -82,6 +82,65 @@ static int vidioc_querycap(struct file *file, void *fh,
 	return 0;
 }
 
+static int capture_enum_framesizes(struct file *file, void *fh,
+				   struct v4l2_frmsizeenum *fsize)
+{
+	struct capture_priv *priv = video_drvdata(file);
+	const struct imx_media_pixfmt *cc;
+	struct v4l2_subdev_frame_size_enum fse = {
+		.index = fsize->index,
+		.pad = priv->src_sd_pad,
+		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
+	};
+	int ret;
+
+	cc = imx_media_find_format(fsize->pixel_format, CS_SEL_ANY, true);
+	if (!cc)
+		return -EINVAL;
+
+	fse.code = cc->codes[0];
+
+	ret = v4l2_subdev_call(priv->src_sd, pad, enum_frame_size, NULL, &fse);
+	if (ret)
+		return ret;
+
+	fsize->type = V4L2_FRMSIZE_TYPE_DISCRETE;
+	fsize->discrete.width = fse.min_width;
+	fsize->discrete.height = fse.max_height;
+
+	return 0;
+}
+
+static int capture_enum_frameintervals(struct file *file, void *fh,
+				       struct v4l2_frmivalenum *fival)
+{
+	struct capture_priv *priv = video_drvdata(file);
+	const struct imx_media_pixfmt *cc;
+	struct v4l2_subdev_frame_interval_enum fie = {
+		.index = fival->index,
+		.pad = priv->src_sd_pad,
+		.width = fival->width,
+		.height = fival->height,
+		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
+	};
+	int ret;
+
+	cc = imx_media_find_format(fival->pixel_format, CS_SEL_ANY, true);
+	if (!cc)
+		return -EINVAL;
+
+	fie.code = cc->codes[0];
+
+	ret = v4l2_subdev_call(priv->src_sd, pad, enum_frame_interval, NULL, &fie);
+	if (ret)
+		return ret;
+
+	fival->type = V4L2_FRMIVAL_TYPE_DISCRETE;
+	fival->discrete = fie.interval;
+
+	return 0;
+}
+
 static int capture_enum_fmt_vid_cap(struct file *file, void *fh,
 				    struct v4l2_fmtdesc *f)
 {
@@ -270,6 +329,9 @@ static int capture_s_parm(struct file *file, void *fh,
 static const struct v4l2_ioctl_ops capture_ioctl_ops = {
 	.vidioc_querycap	= vidioc_querycap,
 
+	.vidioc_enum_framesizes = capture_enum_framesizes,
+	.vidioc_enum_frameintervals = capture_enum_frameintervals,
+
 	.vidioc_enum_fmt_vid_cap        = capture_enum_fmt_vid_cap,
 	.vidioc_g_fmt_vid_cap           = capture_g_fmt_vid_cap,
 	.vidioc_try_fmt_vid_cap         = capture_try_fmt_vid_cap,
-- 
2.7.4

[PATCH 4/4] media: imx-media-capture: add frame sizes/interval enumeration

[Russell King]

Add support for enumerating frame sizes and frame intervals from the
first subdev via the V4L2 interfaces.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 drivers/staging/media/imx/imx-media-capture.c | 62 +++++++++++++++++++++++++++
 1 file changed, 62 insertions(+)

diff --git a/drivers/staging/media/imx/imx-media-capture.c b/drivers/staging/media/imx/imx-media-capture.c
index cdeb2cd8b1d7..bc99d9310e36 100644
--- a/drivers/staging/media/imx/imx-media-capture.c
+++ b/drivers/staging/media/imx/imx-media-capture.c
@@ -82,6 +82,65 @@ static int vidioc_querycap(struct file *file, void *fh,
 	return 0;
 }
 
+static int capture_enum_framesizes(struct file *file, void *fh,
+				   struct v4l2_frmsizeenum *fsize)
+{
+	struct capture_priv *priv = video_drvdata(file);
+	const struct imx_media_pixfmt *cc;
+	struct v4l2_subdev_frame_size_enum fse = {
+		.index = fsize->index,
+		.pad = priv->src_sd_pad,
+		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
+	};
+	int ret;
+
+	cc = imx_media_find_format(fsize->pixel_format, CS_SEL_ANY, true);
+	if (!cc)
+		return -EINVAL;
+
+	fse.code = cc->codes[0];
+
+	ret = v4l2_subdev_call(priv->src_sd, pad, enum_frame_size, NULL, &fse);
+	if (ret)
+		return ret;
+
+	fsize->type = V4L2_FRMSIZE_TYPE_DISCRETE;
+	fsize->discrete.width = fse.min_width;
+	fsize->discrete.height = fse.max_height;
+
+	return 0;
+}
+
+static int capture_enum_frameintervals(struct file *file, void *fh,
+				       struct v4l2_frmivalenum *fival)
+{
+	struct capture_priv *priv = video_drvdata(file);
+	const struct imx_media_pixfmt *cc;
+	struct v4l2_subdev_frame_interval_enum fie = {
+		.index = fival->index,
+		.pad = priv->src_sd_pad,
+		.width = fival->width,
+		.height = fival->height,
+		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
+	};
+	int ret;
+
+	cc = imx_media_find_format(fival->pixel_format, CS_SEL_ANY, true);
+	if (!cc)
+		return -EINVAL;
+
+	fie.code = cc->codes[0];
+
+	ret = v4l2_subdev_call(priv->src_sd, pad, enum_frame_interval, NULL, &fie);
+	if (ret)
+		return ret;
+
+	fival->type = V4L2_FRMIVAL_TYPE_DISCRETE;
+	fival->discrete = fie.interval;
+
+	return 0;
+}
+
 static int capture_enum_fmt_vid_cap(struct file *file, void *fh,
 				    struct v4l2_fmtdesc *f)
 {
@@ -270,6 +329,9 @@ static int capture_s_parm(struct file *file, void *fh,
 static const struct v4l2_ioctl_ops capture_ioctl_ops = {
 	.vidioc_querycap	= vidioc_querycap,
 
+	.vidioc_enum_framesizes = capture_enum_framesizes,
+	.vidioc_enum_frameintervals = capture_enum_frameintervals,
+
 	.vidioc_enum_fmt_vid_cap        = capture_enum_fmt_vid_cap,
 	.vidioc_g_fmt_vid_cap           = capture_g_fmt_vid_cap,
 	.vidioc_try_fmt_vid_cap         = capture_try_fmt_vid_cap,
-- 
2.7.4

Re: [PATCH 4/4] media: imx-media-capture: add frame sizes/interval enumeration

[Steve Longerbeam]

On 03/19/2017 03:49 AM, Russell King wrote:
> Add support for enumerating frame sizes and frame intervals from the
> first subdev via the V4L2 interfaces.
>
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> ---
>   drivers/staging/media/imx/imx-media-capture.c | 62 +++++++++++++++++++++++++++
>   1 file changed, 62 insertions(+)
>
> diff --git a/drivers/staging/media/imx/imx-media-capture.c b/drivers/staging/media/imx/imx-media-capture.c
> index cdeb2cd8b1d7..bc99d9310e36 100644
> --- a/drivers/staging/media/imx/imx-media-capture.c
> +++ b/drivers/staging/media/imx/imx-media-capture.c
> @@ -82,6 +82,65 @@ static int vidioc_querycap(struct file *file, void *fh,
>   	return 0;
>   }
>   
> +static int capture_enum_framesizes(struct file *file, void *fh,
> +				   struct v4l2_frmsizeenum *fsize)
> +{
> +	struct capture_priv *priv = video_drvdata(file);
> +	const struct imx_media_pixfmt *cc;
> +	struct v4l2_subdev_frame_size_enum fse = {
> +		.index = fsize->index,
> +		.pad = priv->src_sd_pad,
> +		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
> +	};
> +	int ret;
> +
> +	cc = imx_media_find_format(fsize->pixel_format, CS_SEL_ANY, true);
> +	if (!cc)
> +		return -EINVAL;
> +
> +	fse.code = cc->codes[0];
> +
> +	ret = v4l2_subdev_call(priv->src_sd, pad, enum_frame_size, NULL, &fse);
> +	if (ret)
> +		return ret;
> +
> +	fsize->type = V4L2_FRMSIZE_TYPE_DISCRETE;
> +	fsize->discrete.width = fse.min_width;
> +	fsize->discrete.height = fse.max_height;
> +
> +	return 0;
> +}


The PRP ENC/VF subdevices will return a continuous range of
supported frame sizes at their source pad, so this should be
modified to:

...
     if (fse.min_width == fse.max_width &&
         fse.min_height == fse.max_height) {
         fsize->type = V4L2_FRMSIZE_TYPE_DISCRETE;
         fsize->discrete.width = fse.min_width;
         fsize->discrete.height = fse.min_height;
     } else {
         fsize->type = V4L2_FRMSIZE_TYPE_CONTINUOUS;
         fsize->stepwise.min_width = fse.min_width;
         fsize->stepwise.max_width = fse.max_width;
         fsize->stepwise.min_height = fse.min_height;
         fsize->stepwise.max_height = fse.max_height;
         fsize->stepwise.step_width = 1;
         fsize->stepwise.step_height = 1;
     }
...

Steve


> +
> +static int capture_enum_frameintervals(struct file *file, void *fh,
> +				       struct v4l2_frmivalenum *fival)
> +{
> +	struct capture_priv *priv = video_drvdata(file);
> +	const struct imx_media_pixfmt *cc;
> +	struct v4l2_subdev_frame_interval_enum fie = {
> +		.index = fival->index,
> +		.pad = priv->src_sd_pad,
> +		.width = fival->width,
> +		.height = fival->height,
> +		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
> +	};
> +	int ret;
> +
> +	cc = imx_media_find_format(fival->pixel_format, CS_SEL_ANY, true);
> +	if (!cc)
> +		return -EINVAL;
> +
> +	fie.code = cc->codes[0];
> +
> +	ret = v4l2_subdev_call(priv->src_sd, pad, enum_frame_interval, NULL, &fie);
> +	if (ret)
> +		return ret;
> +
> +	fival->type = V4L2_FRMIVAL_TYPE_DISCRETE;
> +	fival->discrete = fie.interval;
> +
> +	return 0;
> +}
> +
>   static int capture_enum_fmt_vid_cap(struct file *file, void *fh,
>   				    struct v4l2_fmtdesc *f)
>   {
> @@ -270,6 +329,9 @@ static int capture_s_parm(struct file *file, void *fh,
>   static const struct v4l2_ioctl_ops capture_ioctl_ops = {
>   	.vidioc_querycap	= vidioc_querycap,
>   
> +	.vidioc_enum_framesizes = capture_enum_framesizes,
> +	.vidioc_enum_frameintervals = capture_enum_frameintervals,
> +
>   	.vidioc_enum_fmt_vid_cap        = capture_enum_fmt_vid_cap,
>   	.vidioc_g_fmt_vid_cap           = capture_g_fmt_vid_cap,
>   	.vidioc_try_fmt_vid_cap         = capture_try_fmt_vid_cap,

[PATCH 4/4] media: imx-media-capture: add frame sizes/interval enumeration

[Steve Longerbeam]

On 03/19/2017 03:49 AM, Russell King wrote:
> Add support for enumerating frame sizes and frame intervals from the
> first subdev via the V4L2 interfaces.
>
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> ---
>   drivers/staging/media/imx/imx-media-capture.c | 62 +++++++++++++++++++++++++++
>   1 file changed, 62 insertions(+)
>
> diff --git a/drivers/staging/media/imx/imx-media-capture.c b/drivers/staging/media/imx/imx-media-capture.c
> index cdeb2cd8b1d7..bc99d9310e36 100644
> --- a/drivers/staging/media/imx/imx-media-capture.c
> +++ b/drivers/staging/media/imx/imx-media-capture.c
> @@ -82,6 +82,65 @@ static int vidioc_querycap(struct file *file, void *fh,
>   	return 0;
>   }
>   
> +static int capture_enum_framesizes(struct file *file, void *fh,
> +				   struct v4l2_frmsizeenum *fsize)
> +{
> +	struct capture_priv *priv = video_drvdata(file);
> +	const struct imx_media_pixfmt *cc;
> +	struct v4l2_subdev_frame_size_enum fse = {
> +		.index = fsize->index,
> +		.pad = priv->src_sd_pad,
> +		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
> +	};
> +	int ret;
> +
> +	cc = imx_media_find_format(fsize->pixel_format, CS_SEL_ANY, true);
> +	if (!cc)
> +		return -EINVAL;
> +
> +	fse.code = cc->codes[0];
> +
> +	ret = v4l2_subdev_call(priv->src_sd, pad, enum_frame_size, NULL, &fse);
> +	if (ret)
> +		return ret;
> +
> +	fsize->type = V4L2_FRMSIZE_TYPE_DISCRETE;
> +	fsize->discrete.width = fse.min_width;
> +	fsize->discrete.height = fse.max_height;
> +
> +	return 0;
> +}


The PRP ENC/VF subdevices will return a continuous range of
supported frame sizes at their source pad, so this should be
modified to:

...
     if (fse.min_width == fse.max_width &&
         fse.min_height == fse.max_height) {
         fsize->type = V4L2_FRMSIZE_TYPE_DISCRETE;
         fsize->discrete.width = fse.min_width;
         fsize->discrete.height = fse.min_height;
     } else {
         fsize->type = V4L2_FRMSIZE_TYPE_CONTINUOUS;
         fsize->stepwise.min_width = fse.min_width;
         fsize->stepwise.max_width = fse.max_width;
         fsize->stepwise.min_height = fse.min_height;
         fsize->stepwise.max_height = fse.max_height;
         fsize->stepwise.step_width = 1;
         fsize->stepwise.step_height = 1;
     }
...

Steve


> +
> +static int capture_enum_frameintervals(struct file *file, void *fh,
> +				       struct v4l2_frmivalenum *fival)
> +{
> +	struct capture_priv *priv = video_drvdata(file);
> +	const struct imx_media_pixfmt *cc;
> +	struct v4l2_subdev_frame_interval_enum fie = {
> +		.index = fival->index,
> +		.pad = priv->src_sd_pad,
> +		.width = fival->width,
> +		.height = fival->height,
> +		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
> +	};
> +	int ret;
> +
> +	cc = imx_media_find_format(fival->pixel_format, CS_SEL_ANY, true);
> +	if (!cc)
> +		return -EINVAL;
> +
> +	fie.code = cc->codes[0];
> +
> +	ret = v4l2_subdev_call(priv->src_sd, pad, enum_frame_interval, NULL, &fie);
> +	if (ret)
> +		return ret;
> +
> +	fival->type = V4L2_FRMIVAL_TYPE_DISCRETE;
> +	fival->discrete = fie.interval;
> +
> +	return 0;
> +}
> +
>   static int capture_enum_fmt_vid_cap(struct file *file, void *fh,
>   				    struct v4l2_fmtdesc *f)
>   {
> @@ -270,6 +329,9 @@ static int capture_s_parm(struct file *file, void *fh,
>   static const struct v4l2_ioctl_ops capture_ioctl_ops = {
>   	.vidioc_querycap	= vidioc_querycap,
>   
> +	.vidioc_enum_framesizes = capture_enum_framesizes,
> +	.vidioc_enum_frameintervals = capture_enum_frameintervals,
> +
>   	.vidioc_enum_fmt_vid_cap        = capture_enum_fmt_vid_cap,
>   	.vidioc_g_fmt_vid_cap           = capture_g_fmt_vid_cap,
>   	.vidioc_try_fmt_vid_cap         = capture_try_fmt_vid_cap,

Re: [PATCH 4/4] media: imx-media-capture: add frame sizes/interval enumeration

[Russell King - ARM Linux]

On Sun, Mar 19, 2017 at 03:21:37PM -0700, Steve Longerbeam wrote:
> 
> 
> On 03/19/2017 03:49 AM, Russell King wrote:
> >Add support for enumerating frame sizes and frame intervals from the
> >first subdev via the V4L2 interfaces.
> >
> >Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> >---
> >  drivers/staging/media/imx/imx-media-capture.c | 62 +++++++++++++++++++++++++++
> >  1 file changed, 62 insertions(+)
> >
> >diff --git a/drivers/staging/media/imx/imx-media-capture.c b/drivers/staging/media/imx/imx-media-capture.c
> >index cdeb2cd8b1d7..bc99d9310e36 100644
> >--- a/drivers/staging/media/imx/imx-media-capture.c
> >+++ b/drivers/staging/media/imx/imx-media-capture.c
> >@@ -82,6 +82,65 @@ static int vidioc_querycap(struct file *file, void *fh,
> >  	return 0;
> >  }
> >+static int capture_enum_framesizes(struct file *file, void *fh,
> >+				   struct v4l2_frmsizeenum *fsize)
> >+{
> >+	struct capture_priv *priv = video_drvdata(file);
> >+	const struct imx_media_pixfmt *cc;
> >+	struct v4l2_subdev_frame_size_enum fse = {
> >+		.index = fsize->index,
> >+		.pad = priv->src_sd_pad,
> >+		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
> >+	};
> >+	int ret;
> >+
> >+	cc = imx_media_find_format(fsize->pixel_format, CS_SEL_ANY, true);
> >+	if (!cc)
> >+		return -EINVAL;
> >+
> >+	fse.code = cc->codes[0];
> >+
> >+	ret = v4l2_subdev_call(priv->src_sd, pad, enum_frame_size, NULL, &fse);
> >+	if (ret)
> >+		return ret;
> >+
> >+	fsize->type = V4L2_FRMSIZE_TYPE_DISCRETE;
> >+	fsize->discrete.width = fse.min_width;
> >+	fsize->discrete.height = fse.max_height;
> >+
> >+	return 0;
> >+}
> 
> 
> The PRP ENC/VF subdevices will return a continuous range of
> supported frame sizes at their source pad, so this should be
> modified to:
> 
> ...
>     if (fse.min_width == fse.max_width &&
>         fse.min_height == fse.max_height) {
>         fsize->type = V4L2_FRMSIZE_TYPE_DISCRETE;
>         fsize->discrete.width = fse.min_width;
>         fsize->discrete.height = fse.min_height;
>     } else {
>         fsize->type = V4L2_FRMSIZE_TYPE_CONTINUOUS;
>         fsize->stepwise.min_width = fse.min_width;
>         fsize->stepwise.max_width = fse.max_width;
>         fsize->stepwise.min_height = fse.min_height;
>         fsize->stepwise.max_height = fse.max_height;
>         fsize->stepwise.step_width = 1;
>         fsize->stepwise.step_height = 1;
>     }
> ...

Fine by me - I don't have any experience of those subdevices as they're
unusable for me.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH 4/4] media: imx-media-capture: add frame sizes/interval enumeration

[Russell King - ARM Linux]

On Sun, Mar 19, 2017 at 03:21:37PM -0700, Steve Longerbeam wrote:
> 
> 
> On 03/19/2017 03:49 AM, Russell King wrote:
> >Add support for enumerating frame sizes and frame intervals from the
> >first subdev via the V4L2 interfaces.
> >
> >Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> >---
> >  drivers/staging/media/imx/imx-media-capture.c | 62 +++++++++++++++++++++++++++
> >  1 file changed, 62 insertions(+)
> >
> >diff --git a/drivers/staging/media/imx/imx-media-capture.c b/drivers/staging/media/imx/imx-media-capture.c
> >index cdeb2cd8b1d7..bc99d9310e36 100644
> >--- a/drivers/staging/media/imx/imx-media-capture.c
> >+++ b/drivers/staging/media/imx/imx-media-capture.c
> >@@ -82,6 +82,65 @@ static int vidioc_querycap(struct file *file, void *fh,
> >  	return 0;
> >  }
> >+static int capture_enum_framesizes(struct file *file, void *fh,
> >+				   struct v4l2_frmsizeenum *fsize)
> >+{
> >+	struct capture_priv *priv = video_drvdata(file);
> >+	const struct imx_media_pixfmt *cc;
> >+	struct v4l2_subdev_frame_size_enum fse = {
> >+		.index = fsize->index,
> >+		.pad = priv->src_sd_pad,
> >+		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
> >+	};
> >+	int ret;
> >+
> >+	cc = imx_media_find_format(fsize->pixel_format, CS_SEL_ANY, true);
> >+	if (!cc)
> >+		return -EINVAL;
> >+
> >+	fse.code = cc->codes[0];
> >+
> >+	ret = v4l2_subdev_call(priv->src_sd, pad, enum_frame_size, NULL, &fse);
> >+	if (ret)
> >+		return ret;
> >+
> >+	fsize->type = V4L2_FRMSIZE_TYPE_DISCRETE;
> >+	fsize->discrete.width = fse.min_width;
> >+	fsize->discrete.height = fse.max_height;
> >+
> >+	return 0;
> >+}
> 
> 
> The PRP ENC/VF subdevices will return a continuous range of
> supported frame sizes at their source pad, so this should be
> modified to:
> 
> ...
>     if (fse.min_width == fse.max_width &&
>         fse.min_height == fse.max_height) {
>         fsize->type = V4L2_FRMSIZE_TYPE_DISCRETE;
>         fsize->discrete.width = fse.min_width;
>         fsize->discrete.height = fse.min_height;
>     } else {
>         fsize->type = V4L2_FRMSIZE_TYPE_CONTINUOUS;
>         fsize->stepwise.min_width = fse.min_width;
>         fsize->stepwise.max_width = fse.max_width;
>         fsize->stepwise.min_height = fse.min_height;
>         fsize->stepwise.max_height = fse.max_height;
>         fsize->stepwise.step_width = 1;
>         fsize->stepwise.step_height = 1;
>     }
> ...

Fine by me - I don't have any experience of those subdevices as they're
unusable for me.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH 4/4] media: imx-media-capture: add frame sizes/interval enumeration

[Philippe De Muyter]

Hi Russel,

On Sun, Mar 19, 2017 at 10:49:08AM +0000, Russell King wrote:
> Add support for enumerating frame sizes and frame intervals from the
> first subdev via the V4L2 interfaces.
> 
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> ---
>  drivers/staging/media/imx/imx-media-capture.c | 62 +++++++++++++++++++++++++++
>  1 file changed, 62 insertions(+)
> 
...
> +static int capture_enum_frameintervals(struct file *file, void *fh,
> +				       struct v4l2_frmivalenum *fival)
> +{
> +	struct capture_priv *priv = video_drvdata(file);
> +	const struct imx_media_pixfmt *cc;
> +	struct v4l2_subdev_frame_interval_enum fie = {
> +		.index = fival->index,
> +		.pad = priv->src_sd_pad,
> +		.width = fival->width,
> +		.height = fival->height,
> +		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
> +	};
> +	int ret;
> +
> +	cc = imx_media_find_format(fival->pixel_format, CS_SEL_ANY, true);
> +	if (!cc)
> +		return -EINVAL;
> +
> +	fie.code = cc->codes[0];
> +
> +	ret = v4l2_subdev_call(priv->src_sd, pad, enum_frame_interval, NULL, &fie);
> +	if (ret)
> +		return ret;
> +
> +	fival->type = V4L2_FRMIVAL_TYPE_DISCRETE;
> +	fival->discrete = fie.interval;

For some parallel sensors (mine is a E2V ev76c560) "any" frame interval is possible,
and hence type should be V4L2_FRMIVAL_TYPE_CONTINUOUS.

see also https://www.spinics.net/lists/linux-media/msg98622.html,
https://patchwork.kernel.org/patch/9171201/ and
https://patchwork.kernel.org/patch/9171199/

Philippe

-- 
Philippe De Muyter +32 2 6101532 Macq SA rue de l'Aeronef 2 B-1140 Bruxelles

[PATCH 4/4] media: imx-media-capture: add frame sizes/interval enumeration

[Philippe De Muyter]

Hi Russel,

On Sun, Mar 19, 2017 at 10:49:08AM +0000, Russell King wrote:
> Add support for enumerating frame sizes and frame intervals from the
> first subdev via the V4L2 interfaces.
> 
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> ---
>  drivers/staging/media/imx/imx-media-capture.c | 62 +++++++++++++++++++++++++++
>  1 file changed, 62 insertions(+)
> 
...
> +static int capture_enum_frameintervals(struct file *file, void *fh,
> +				       struct v4l2_frmivalenum *fival)
> +{
> +	struct capture_priv *priv = video_drvdata(file);
> +	const struct imx_media_pixfmt *cc;
> +	struct v4l2_subdev_frame_interval_enum fie = {
> +		.index = fival->index,
> +		.pad = priv->src_sd_pad,
> +		.width = fival->width,
> +		.height = fival->height,
> +		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
> +	};
> +	int ret;
> +
> +	cc = imx_media_find_format(fival->pixel_format, CS_SEL_ANY, true);
> +	if (!cc)
> +		return -EINVAL;
> +
> +	fie.code = cc->codes[0];
> +
> +	ret = v4l2_subdev_call(priv->src_sd, pad, enum_frame_interval, NULL, &fie);
> +	if (ret)
> +		return ret;
> +
> +	fival->type = V4L2_FRMIVAL_TYPE_DISCRETE;
> +	fival->discrete = fie.interval;

For some parallel sensors (mine is a E2V ev76c560) "any" frame interval is possible,
and hence type should be V4L2_FRMIVAL_TYPE_CONTINUOUS.

see also https://www.spinics.net/lists/linux-media/msg98622.html,
https://patchwork.kernel.org/patch/9171201/ and
https://patchwork.kernel.org/patch/9171199/

Philippe

-- 
Philippe De Muyter +32 2 6101532 Macq SA rue de l'Aeronef 2 B-1140 Bruxelles

Re: [PATCH 4/4] media: imx-media-capture: add frame sizes/interval enumeration

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 09:55:12AM +0100, Philippe De Muyter wrote:
> Hi Russel,
> 
> On Sun, Mar 19, 2017 at 10:49:08AM +0000, Russell King wrote:
> > Add support for enumerating frame sizes and frame intervals from the
> > first subdev via the V4L2 interfaces.
> > 
> > Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> > ---
> >  drivers/staging/media/imx/imx-media-capture.c | 62 +++++++++++++++++++++++++++
> >  1 file changed, 62 insertions(+)
> > 
> ...
> > +static int capture_enum_frameintervals(struct file *file, void *fh,
> > +				       struct v4l2_frmivalenum *fival)
> > +{
> > +	struct capture_priv *priv = video_drvdata(file);
> > +	const struct imx_media_pixfmt *cc;
> > +	struct v4l2_subdev_frame_interval_enum fie = {
> > +		.index = fival->index,
> > +		.pad = priv->src_sd_pad,
> > +		.width = fival->width,
> > +		.height = fival->height,
> > +		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
> > +	};
> > +	int ret;
> > +
> > +	cc = imx_media_find_format(fival->pixel_format, CS_SEL_ANY, true);
> > +	if (!cc)
> > +		return -EINVAL;
> > +
> > +	fie.code = cc->codes[0];
> > +
> > +	ret = v4l2_subdev_call(priv->src_sd, pad, enum_frame_interval, NULL, &fie);
> > +	if (ret)
> > +		return ret;
> > +
> > +	fival->type = V4L2_FRMIVAL_TYPE_DISCRETE;
> > +	fival->discrete = fie.interval;
> 
> For some parallel sensors (mine is a E2V ev76c560) "any" frame interval is possible,
> and hence type should be V4L2_FRMIVAL_TYPE_CONTINUOUS.

For my sensor, any frame interval is also possible, but that isn't the
point here.

/dev/video* only talks to the CSI source pad, not it's sink pad.  The
sink pad gets configured with the sensor frame rate via the media
controller API.  /dev/video* itself has no control over the sensor
frame rate.

The media controller stuff completely changes the way the established
/dev/video* functionality works - the ability to select arbitary frame
sizes and frame rates supported by the ultimate sensor is gone.  All
that needs to be setup through the media controller pipeline, one
subdev at a time.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH 4/4] media: imx-media-capture: add frame sizes/interval enumeration

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 09:55:12AM +0100, Philippe De Muyter wrote:
> Hi Russel,
> 
> On Sun, Mar 19, 2017 at 10:49:08AM +0000, Russell King wrote:
> > Add support for enumerating frame sizes and frame intervals from the
> > first subdev via the V4L2 interfaces.
> > 
> > Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> > ---
> >  drivers/staging/media/imx/imx-media-capture.c | 62 +++++++++++++++++++++++++++
> >  1 file changed, 62 insertions(+)
> > 
> ...
> > +static int capture_enum_frameintervals(struct file *file, void *fh,
> > +				       struct v4l2_frmivalenum *fival)
> > +{
> > +	struct capture_priv *priv = video_drvdata(file);
> > +	const struct imx_media_pixfmt *cc;
> > +	struct v4l2_subdev_frame_interval_enum fie = {
> > +		.index = fival->index,
> > +		.pad = priv->src_sd_pad,
> > +		.width = fival->width,
> > +		.height = fival->height,
> > +		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
> > +	};
> > +	int ret;
> > +
> > +	cc = imx_media_find_format(fival->pixel_format, CS_SEL_ANY, true);
> > +	if (!cc)
> > +		return -EINVAL;
> > +
> > +	fie.code = cc->codes[0];
> > +
> > +	ret = v4l2_subdev_call(priv->src_sd, pad, enum_frame_interval, NULL, &fie);
> > +	if (ret)
> > +		return ret;
> > +
> > +	fival->type = V4L2_FRMIVAL_TYPE_DISCRETE;
> > +	fival->discrete = fie.interval;
> 
> For some parallel sensors (mine is a E2V ev76c560) "any" frame interval is possible,
> and hence type should be V4L2_FRMIVAL_TYPE_CONTINUOUS.

For my sensor, any frame interval is also possible, but that isn't the
point here.

/dev/video* only talks to the CSI source pad, not it's sink pad.  The
sink pad gets configured with the sensor frame rate via the media
controller API.  /dev/video* itself has no control over the sensor
frame rate.

The media controller stuff completely changes the way the established
/dev/video* functionality works - the ability to select arbitary frame
sizes and frame rates supported by the ultimate sensor is gone.  All
that needs to be setup through the media controller pipeline, one
subdev at a time.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH 4/4] media: imx-media-capture: add frame sizes/interval enumeration

[Philippe De Muyter]

On Mon, Mar 20, 2017 at 09:05:25AM +0000, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 09:55:12AM +0100, Philippe De Muyter wrote:
> > Hi Russel,
> > 
> > On Sun, Mar 19, 2017 at 10:49:08AM +0000, Russell King wrote:
> > > Add support for enumerating frame sizes and frame intervals from the
> > > first subdev via the V4L2 interfaces.
> > > 
> > > Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> > > ---
> > >  drivers/staging/media/imx/imx-media-capture.c | 62 +++++++++++++++++++++++++++
> > >  1 file changed, 62 insertions(+)
> > > 
> > ...
> > > +static int capture_enum_frameintervals(struct file *file, void *fh,
> > > +				       struct v4l2_frmivalenum *fival)
> > > +{
> > > +	struct capture_priv *priv = video_drvdata(file);
> > > +	const struct imx_media_pixfmt *cc;
> > > +	struct v4l2_subdev_frame_interval_enum fie = {
> > > +		.index = fival->index,
> > > +		.pad = priv->src_sd_pad,
> > > +		.width = fival->width,
> > > +		.height = fival->height,
> > > +		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
> > > +	};
> > > +	int ret;
> > > +
> > > +	cc = imx_media_find_format(fival->pixel_format, CS_SEL_ANY, true);
> > > +	if (!cc)
> > > +		return -EINVAL;
> > > +
> > > +	fie.code = cc->codes[0];
> > > +
> > > +	ret = v4l2_subdev_call(priv->src_sd, pad, enum_frame_interval, NULL, &fie);
> > > +	if (ret)
> > > +		return ret;
> > > +
> > > +	fival->type = V4L2_FRMIVAL_TYPE_DISCRETE;
> > > +	fival->discrete = fie.interval;
> > 
> > For some parallel sensors (mine is a E2V ev76c560) "any" frame interval is possible,
> > and hence type should be V4L2_FRMIVAL_TYPE_CONTINUOUS.
> 
> For my sensor, any frame interval is also possible, but that isn't the
> point here.
> 
> /dev/video* only talks to the CSI source pad, not it's sink pad.  The
> sink pad gets configured with the sensor frame rate via the media
> controller API.  /dev/video* itself has no control over the sensor
> frame rate.
> 
> The media controller stuff completely changes the way the established
> /dev/video* functionality works - the ability to select arbitary frame
> sizes and frame rates supported by the ultimate sensor is gone.  All
> that needs to be setup through the media controller pipeline, one
> subdev at a time.
> 
So existing gstreamer applications using /dev/video* to control framerate,
and even gain and exposure won't work anymore :( ?

I had hoped to keep compatibility, with added robustness and functionality.

I seems like I'll stay with my NXP/Freescale old and imperfect kernel.

Best regards

Philippe

-- 
Philippe De Muyter +32 2 6101532 Macq SA rue de l'Aeronef 2 B-1140 Bruxelles

[PATCH 4/4] media: imx-media-capture: add frame sizes/interval enumeration

[Philippe De Muyter]

On Mon, Mar 20, 2017 at 09:05:25AM +0000, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 09:55:12AM +0100, Philippe De Muyter wrote:
> > Hi Russel,
> > 
> > On Sun, Mar 19, 2017 at 10:49:08AM +0000, Russell King wrote:
> > > Add support for enumerating frame sizes and frame intervals from the
> > > first subdev via the V4L2 interfaces.
> > > 
> > > Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> > > ---
> > >  drivers/staging/media/imx/imx-media-capture.c | 62 +++++++++++++++++++++++++++
> > >  1 file changed, 62 insertions(+)
> > > 
> > ...
> > > +static int capture_enum_frameintervals(struct file *file, void *fh,
> > > +				       struct v4l2_frmivalenum *fival)
> > > +{
> > > +	struct capture_priv *priv = video_drvdata(file);
> > > +	const struct imx_media_pixfmt *cc;
> > > +	struct v4l2_subdev_frame_interval_enum fie = {
> > > +		.index = fival->index,
> > > +		.pad = priv->src_sd_pad,
> > > +		.width = fival->width,
> > > +		.height = fival->height,
> > > +		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
> > > +	};
> > > +	int ret;
> > > +
> > > +	cc = imx_media_find_format(fival->pixel_format, CS_SEL_ANY, true);
> > > +	if (!cc)
> > > +		return -EINVAL;
> > > +
> > > +	fie.code = cc->codes[0];
> > > +
> > > +	ret = v4l2_subdev_call(priv->src_sd, pad, enum_frame_interval, NULL, &fie);
> > > +	if (ret)
> > > +		return ret;
> > > +
> > > +	fival->type = V4L2_FRMIVAL_TYPE_DISCRETE;
> > > +	fival->discrete = fie.interval;
> > 
> > For some parallel sensors (mine is a E2V ev76c560) "any" frame interval is possible,
> > and hence type should be V4L2_FRMIVAL_TYPE_CONTINUOUS.
> 
> For my sensor, any frame interval is also possible, but that isn't the
> point here.
> 
> /dev/video* only talks to the CSI source pad, not it's sink pad.  The
> sink pad gets configured with the sensor frame rate via the media
> controller API.  /dev/video* itself has no control over the sensor
> frame rate.
> 
> The media controller stuff completely changes the way the established
> /dev/video* functionality works - the ability to select arbitary frame
> sizes and frame rates supported by the ultimate sensor is gone.  All
> that needs to be setup through the media controller pipeline, one
> subdev at a time.
> 
So existing gstreamer applications using /dev/video* to control framerate,
and even gain and exposure won't work anymore :( ?

I had hoped to keep compatibility, with added robustness and functionality.

I seems like I'll stay with my NXP/Freescale old and imperfect kernel.

Best regards

Philippe

-- 
Philippe De Muyter +32 2 6101532 Macq SA rue de l'Aeronef 2 B-1140 Bruxelles

Re: [PATCH 4/4] media: imx-media-capture: add frame sizes/interval enumeration

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 10:23:30AM +0100, Philippe De Muyter wrote:
> So existing gstreamer applications using /dev/video* to control framerate,
> and even gain and exposure won't work anymore :( ?
> 
> I had hoped to keep compatibility, with added robustness and functionality.
> 
> I seems like I'll stay with my NXP/Freescale old and imperfect kernel.

Thank you for saying this, this supports my views which I've already
stated about what influences which kernel people will use.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH 4/4] media: imx-media-capture: add frame sizes/interval enumeration

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 10:23:30AM +0100, Philippe De Muyter wrote:
> So existing gstreamer applications using /dev/video* to control framerate,
> and even gain and exposure won't work anymore :( ?
> 
> I had hoped to keep compatibility, with added robustness and functionality.
> 
> I seems like I'll stay with my NXP/Freescale old and imperfect kernel.

Thank you for saying this, this supports my views which I've already
stated about what influences which kernel people will use.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/19/2017 03:38 AM, Russell King - ARM Linux wrote:
> On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
>> Right, imx-media-capture.c (the "standard" v4l2 user interface module)
>> is not implementing VIDIOC_ENUM_FRAMESIZES. It should, but it can only
>> return the single frame size that the pipeline has configured (the mbus
>> format of the attached source pad).
> I now have a set of patches that enumerate the frame sizes and intervals
> from the source pad of the first subdev (since you're setting the formats
> etc there from the capture device, it seems sensible to return what it
> can support.)  This means my patch set doesn't add to non-CSI subdevs.
>
>> Can you share your gstreamer pipeline? For now, until
>> VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
>> does not attempt to specify a frame rate. I use the attached
>> script for testing, which works for me.
> Note that I'm not specifying a frame rate on gstreamer - I'm setting
> the pipeline up for 60fps, but gstreamer in its wisdom is unable to
> enumerate the frame sizes, and therefore is unable to enumerate the
> frame intervals (frame intervals depend on frame sizes), so it
> falls back to the "tvnorms" which are basically 25/1 and 30000/1001.
>
> It sees 60fps via G_PARM, and then decides to set 30000/1001 via S_PARM.
> So, we end up with most of the pipeline operating at 60fps, with CSI
> doing frame skipping to reduce the frame rate to 30fps.
>
> gstreamer doesn't complain, doesn't issue any warnings, the only way
> you can spot this is to enable debugging and look through the copious
> debug log, or use -v and check the pad capabilities.
>
> Testing using gstreamer, and only using "does it produce video" is a
> good simple test, but it's just that - it's a simple test.  It doesn't
> tell you that what you're seeing is what you intended to see (such as
> video at the frame rate you expected) without more work.
>
>> Thanks, I've fixed most of v4l2-compliance issues, but this is not
>> done yet. Is that something you can help with?
> What did you do with:
>
> ioctl(3, VIDIOC_REQBUFS, {count=0, type=0 /* V4L2_BUF_TYPE_??? */, memory=0 /* V4L2_MEMORY_??? */}) = -1 EINVAL (Invalid argument)
>                  test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
> ioctl(3, VIDIOC_EXPBUF, 0xbef405bc)     = -1 EINVAL (Invalid argument)
>                  fail: v4l2-test-buffers.cpp(571): q.has_expbuf(node)
>                  test VIDIOC_EXPBUF: FAIL
>
> To me, this looks like a bug in v4l2-compliance (I'm using 1.10.0).
> I'm not sure what buffer VIDIOC_EXPBUF is expected to export, since
> afaics no buffers have been allocated, so of course it's going to fail.
> Either that, or the v4l2 core vb2 code is non-compliant with v4l2's
> interface requirements.
>
> In any case, it doesn't look like the buffer management is being
> tested at all by v4l2-compliance - we know that gstreamer works, so
> buffers _can_ be allocated, and I've also used dmabufs with gstreamer,
> so I also know that VIDIOC_EXPBUF works there.
>

I wouldn't be surprised if you hit on a bug in v4l2-compliance. I 
stopped with v4l2-compliance
at a different test failure that also didn't make sense to me:

Streaming ioctls:
     test read/write: OK (Not Supported)
         Video Capture:
         Buffer: 0 Sequence: 0 Field: Any Timestamp: 41.664259s
         fail: 
.../v4l-utils-1.6.2/utils/v4l2-compliance/v4l2-test-buffers.cpp(281): 
!(g_flags() & (V4L2_BUF_FLAG_DONE | V4L2_BUF_FLAG_ERROR))
         fail: 
.../v4l-utils-1.6.2/utils/v4l2-compliance/v4l2-test-buffers.cpp(610): 
buf.check(q, last_seq)
         fail: 
.../v4l-utils-1.6.2/utils/v4l2-compliance/v4l2-test-buffers.cpp(883): 
captureBufs(node, q, m2m_q, frame_count, false)
     test MMAP: FAIL
     test USERPTR: OK (Not Supported)
     test DMABUF: Cannot test, specify --expbuf-device

Total: 42, Succeeded: 38, Failed: 4, Warnings: 0


In this case the driver completed and returned only one buffer, and it set
VB2_BUF_STATE_DONE, so these test failures didn't make sense to me. I
was using version 1.6.2 at the time.

Steve

[PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/19/2017 03:38 AM, Russell King - ARM Linux wrote:
> On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
>> Right, imx-media-capture.c (the "standard" v4l2 user interface module)
>> is not implementing VIDIOC_ENUM_FRAMESIZES. It should, but it can only
>> return the single frame size that the pipeline has configured (the mbus
>> format of the attached source pad).
> I now have a set of patches that enumerate the frame sizes and intervals
> from the source pad of the first subdev (since you're setting the formats
> etc there from the capture device, it seems sensible to return what it
> can support.)  This means my patch set doesn't add to non-CSI subdevs.
>
>> Can you share your gstreamer pipeline? For now, until
>> VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
>> does not attempt to specify a frame rate. I use the attached
>> script for testing, which works for me.
> Note that I'm not specifying a frame rate on gstreamer - I'm setting
> the pipeline up for 60fps, but gstreamer in its wisdom is unable to
> enumerate the frame sizes, and therefore is unable to enumerate the
> frame intervals (frame intervals depend on frame sizes), so it
> falls back to the "tvnorms" which are basically 25/1 and 30000/1001.
>
> It sees 60fps via G_PARM, and then decides to set 30000/1001 via S_PARM.
> So, we end up with most of the pipeline operating at 60fps, with CSI
> doing frame skipping to reduce the frame rate to 30fps.
>
> gstreamer doesn't complain, doesn't issue any warnings, the only way
> you can spot this is to enable debugging and look through the copious
> debug log, or use -v and check the pad capabilities.
>
> Testing using gstreamer, and only using "does it produce video" is a
> good simple test, but it's just that - it's a simple test.  It doesn't
> tell you that what you're seeing is what you intended to see (such as
> video at the frame rate you expected) without more work.
>
>> Thanks, I've fixed most of v4l2-compliance issues, but this is not
>> done yet. Is that something you can help with?
> What did you do with:
>
> ioctl(3, VIDIOC_REQBUFS, {count=0, type=0 /* V4L2_BUF_TYPE_??? */, memory=0 /* V4L2_MEMORY_??? */}) = -1 EINVAL (Invalid argument)
>                  test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
> ioctl(3, VIDIOC_EXPBUF, 0xbef405bc)     = -1 EINVAL (Invalid argument)
>                  fail: v4l2-test-buffers.cpp(571): q.has_expbuf(node)
>                  test VIDIOC_EXPBUF: FAIL
>
> To me, this looks like a bug in v4l2-compliance (I'm using 1.10.0).
> I'm not sure what buffer VIDIOC_EXPBUF is expected to export, since
> afaics no buffers have been allocated, so of course it's going to fail.
> Either that, or the v4l2 core vb2 code is non-compliant with v4l2's
> interface requirements.
>
> In any case, it doesn't look like the buffer management is being
> tested at all by v4l2-compliance - we know that gstreamer works, so
> buffers _can_ be allocated, and I've also used dmabufs with gstreamer,
> so I also know that VIDIOC_EXPBUF works there.
>

I wouldn't be surprised if you hit on a bug in v4l2-compliance. I 
stopped with v4l2-compliance
at a different test failure that also didn't make sense to me:

Streaming ioctls:
     test read/write: OK (Not Supported)
         Video Capture:
         Buffer: 0 Sequence: 0 Field: Any Timestamp: 41.664259s
         fail: 
.../v4l-utils-1.6.2/utils/v4l2-compliance/v4l2-test-buffers.cpp(281): 
!(g_flags() & (V4L2_BUF_FLAG_DONE | V4L2_BUF_FLAG_ERROR))
         fail: 
.../v4l-utils-1.6.2/utils/v4l2-compliance/v4l2-test-buffers.cpp(610): 
buf.check(q, last_seq)
         fail: 
.../v4l-utils-1.6.2/utils/v4l2-compliance/v4l2-test-buffers.cpp(883): 
captureBufs(node, q, m2m_q, frame_count, false)
     test MMAP: FAIL
     test USERPTR: OK (Not Supported)
     test DMABUF: Cannot test, specify --expbuf-device

Total: 42, Succeeded: 38, Failed: 4, Warnings: 0


In this case the driver completed and returned only one buffer, and it set
VB2_BUF_STATE_DONE, so these test failures didn't make sense to me. I
was using version 1.6.2 at the time.

Steve

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/19/2017 03:38 AM, Russell King - ARM Linux wrote:
> On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
>> Right, imx-media-capture.c (the "standard" v4l2 user interface module)
>> is not implementing VIDIOC_ENUM_FRAMESIZES. It should, but it can only
>> return the single frame size that the pipeline has configured (the mbus
>> format of the attached source pad).
> I now have a set of patches that enumerate the frame sizes and intervals
> from the source pad of the first subdev (since you're setting the formats
> etc there from the capture device, it seems sensible to return what it
> can support.)  This means my patch set doesn't add to non-CSI subdevs.
>
>> Can you share your gstreamer pipeline? For now, until
>> VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
>> does not attempt to specify a frame rate. I use the attached
>> script for testing, which works for me.
> Note that I'm not specifying a frame rate on gstreamer - I'm setting
> the pipeline up for 60fps, but gstreamer in its wisdom is unable to
> enumerate the frame sizes, and therefore is unable to enumerate the
> frame intervals (frame intervals depend on frame sizes), so it
> falls back to the "tvnorms" which are basically 25/1 and 30000/1001.
>
> It sees 60fps via G_PARM, and then decides to set 30000/1001 via S_PARM.
> So, we end up with most of the pipeline operating at 60fps, with CSI
> doing frame skipping to reduce the frame rate to 30fps.
>
> gstreamer doesn't complain, doesn't issue any warnings, the only way
> you can spot this is to enable debugging and look through the copious
> debug log, or use -v and check the pad capabilities.
>
> Testing using gstreamer, and only using "does it produce video" is a
> good simple test, but it's just that - it's a simple test.  It doesn't
> tell you that what you're seeing is what you intended to see (such as
> video at the frame rate you expected) without more work.
>
>> Thanks, I've fixed most of v4l2-compliance issues, but this is not
>> done yet. Is that something you can help with?
> What did you do with:
>
> ioctl(3, VIDIOC_REQBUFS, {count=0, type=0 /* V4L2_BUF_TYPE_??? */, memory=0 /* V4L2_MEMORY_??? */}) = -1 EINVAL (Invalid argument)
>                  test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
> ioctl(3, VIDIOC_EXPBUF, 0xbef405bc)     = -1 EINVAL (Invalid argument)
>                  fail: v4l2-test-buffers.cpp(571): q.has_expbuf(node)
>                  test VIDIOC_EXPBUF: FAIL
>
> To me, this looks like a bug in v4l2-compliance (I'm using 1.10.0).
> I'm not sure what buffer VIDIOC_EXPBUF is expected to export, since
> afaics no buffers have been allocated, so of course it's going to fail.
> Either that, or the v4l2 core vb2 code is non-compliant with v4l2's
> interface requirements.
>
> In any case, it doesn't look like the buffer management is being
> tested at all by v4l2-compliance - we know that gstreamer works, so
> buffers _can_ be allocated, and I've also used dmabufs with gstreamer,
> so I also know that VIDIOC_EXPBUF works there.
>

I wouldn't be surprised if you hit on a bug in v4l2-compliance. I 
stopped with v4l2-compliance
at a different test failure that also didn't make sense to me:

Streaming ioctls:
     test read/write: OK (Not Supported)
         Video Capture:
         Buffer: 0 Sequence: 0 Field: Any Timestamp: 41.664259s
         fail: 
.../v4l-utils-1.6.2/utils/v4l2-compliance/v4l2-test-buffers.cpp(281): 
!(g_flags() & (V4L2_BUF_FLAG_DONE | V4L2_BUF_FLAG_ERROR))
         fail: 
.../v4l-utils-1.6.2/utils/v4l2-compliance/v4l2-test-buffers.cpp(610): 
buf.check(q, last_seq)
         fail: 
.../v4l-utils-1.6.2/utils/v4l2-compliance/v4l2-test-buffers.cpp(883): 
captureBufs(node, q, m2m_q, frame_count, false)
     test MMAP: FAIL
     test USERPTR: OK (Not Supported)
     test DMABUF: Cannot test, specify --expbuf-device

Total: 42, Succeeded: 38, Failed: 4, Warnings: 0


In this case the driver completed and returned only one buffer, and it set
VB2_BUF_STATE_DONE, so these test failures didn't make sense to me. I
was using version 1.6.2 at the time.

Steve

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 19, 2017 at 10:54:22AM -0700, Steve Longerbeam wrote:
> 
> 
> On 03/19/2017 03:38 AM, Russell King - ARM Linux wrote:
> >On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> >>Right, imx-media-capture.c (the "standard" v4l2 user interface module)
> >>is not implementing VIDIOC_ENUM_FRAMESIZES. It should, but it can only
> >>return the single frame size that the pipeline has configured (the mbus
> >>format of the attached source pad).
> >I now have a set of patches that enumerate the frame sizes and intervals
> >from the source pad of the first subdev (since you're setting the formats
> >etc there from the capture device, it seems sensible to return what it
> >can support.)  This means my patch set doesn't add to non-CSI subdevs.
> >
> >>Can you share your gstreamer pipeline? For now, until
> >>VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
> >>does not attempt to specify a frame rate. I use the attached
> >>script for testing, which works for me.
> >Note that I'm not specifying a frame rate on gstreamer - I'm setting
> >the pipeline up for 60fps, but gstreamer in its wisdom is unable to
> >enumerate the frame sizes, and therefore is unable to enumerate the
> >frame intervals (frame intervals depend on frame sizes), so it
> >falls back to the "tvnorms" which are basically 25/1 and 30000/1001.
> >
> >It sees 60fps via G_PARM, and then decides to set 30000/1001 via S_PARM.
> >So, we end up with most of the pipeline operating at 60fps, with CSI
> >doing frame skipping to reduce the frame rate to 30fps.
> >
> >gstreamer doesn't complain, doesn't issue any warnings, the only way
> >you can spot this is to enable debugging and look through the copious
> >debug log, or use -v and check the pad capabilities.
> >
> >Testing using gstreamer, and only using "does it produce video" is a
> >good simple test, but it's just that - it's a simple test.  It doesn't
> >tell you that what you're seeing is what you intended to see (such as
> >video at the frame rate you expected) without more work.
> >
> >>Thanks, I've fixed most of v4l2-compliance issues, but this is not
> >>done yet. Is that something you can help with?
> >What did you do with:
> >
> >ioctl(3, VIDIOC_REQBUFS, {count=0, type=0 /* V4L2_BUF_TYPE_??? */, memory=0 /* V4L2_MEMORY_??? */}) = -1 EINVAL (Invalid argument)
> >                 test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
> >ioctl(3, VIDIOC_EXPBUF, 0xbef405bc)     = -1 EINVAL (Invalid argument)
> >                 fail: v4l2-test-buffers.cpp(571): q.has_expbuf(node)
> >                 test VIDIOC_EXPBUF: FAIL
> >
> >To me, this looks like a bug in v4l2-compliance (I'm using 1.10.0).
> >I'm not sure what buffer VIDIOC_EXPBUF is expected to export, since
> >afaics no buffers have been allocated, so of course it's going to fail.
> >Either that, or the v4l2 core vb2 code is non-compliant with v4l2's
> >interface requirements.
> >
> >In any case, it doesn't look like the buffer management is being
> >tested at all by v4l2-compliance - we know that gstreamer works, so
> >buffers _can_ be allocated, and I've also used dmabufs with gstreamer,
> >so I also know that VIDIOC_EXPBUF works there.
> >
> 
> I wouldn't be surprised if you hit on a bug in v4l2-compliance. I stopped
> with v4l2-compliance
> at a different test failure that also didn't make sense to me:

It isn't - the problem is that the results are misleading.  The
VIDIOC_REQBUFS depends on the GET_FMT test succeeding, so it knows
which buffer formats are valid.

Since the GET_FMT test fails due to the colorspace issue, it decides
that it can't trust the format, so it ends up with no formats to test.
This causes the "VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF" test to pass,
but then it moves on to testing "VIDIOC_EXPBUF" with no available
buffers, which then fails.

Fixing GET_FMT (which I've done locally) to return proper colorspace
information results in GET_FMT passing, and also solves the EXPBUF
problem too.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 19, 2017 at 10:54:22AM -0700, Steve Longerbeam wrote:
> 
> 
> On 03/19/2017 03:38 AM, Russell King - ARM Linux wrote:
> >On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> >>Right, imx-media-capture.c (the "standard" v4l2 user interface module)
> >>is not implementing VIDIOC_ENUM_FRAMESIZES. It should, but it can only
> >>return the single frame size that the pipeline has configured (the mbus
> >>format of the attached source pad).
> >I now have a set of patches that enumerate the frame sizes and intervals
> >from the source pad of the first subdev (since you're setting the formats
> >etc there from the capture device, it seems sensible to return what it
> >can support.)  This means my patch set doesn't add to non-CSI subdevs.
> >
> >>Can you share your gstreamer pipeline? For now, until
> >>VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
> >>does not attempt to specify a frame rate. I use the attached
> >>script for testing, which works for me.
> >Note that I'm not specifying a frame rate on gstreamer - I'm setting
> >the pipeline up for 60fps, but gstreamer in its wisdom is unable to
> >enumerate the frame sizes, and therefore is unable to enumerate the
> >frame intervals (frame intervals depend on frame sizes), so it
> >falls back to the "tvnorms" which are basically 25/1 and 30000/1001.
> >
> >It sees 60fps via G_PARM, and then decides to set 30000/1001 via S_PARM.
> >So, we end up with most of the pipeline operating at 60fps, with CSI
> >doing frame skipping to reduce the frame rate to 30fps.
> >
> >gstreamer doesn't complain, doesn't issue any warnings, the only way
> >you can spot this is to enable debugging and look through the copious
> >debug log, or use -v and check the pad capabilities.
> >
> >Testing using gstreamer, and only using "does it produce video" is a
> >good simple test, but it's just that - it's a simple test.  It doesn't
> >tell you that what you're seeing is what you intended to see (such as
> >video at the frame rate you expected) without more work.
> >
> >>Thanks, I've fixed most of v4l2-compliance issues, but this is not
> >>done yet. Is that something you can help with?
> >What did you do with:
> >
> >ioctl(3, VIDIOC_REQBUFS, {count=0, type=0 /* V4L2_BUF_TYPE_??? */, memory=0 /* V4L2_MEMORY_??? */}) = -1 EINVAL (Invalid argument)
> >                 test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
> >ioctl(3, VIDIOC_EXPBUF, 0xbef405bc)     = -1 EINVAL (Invalid argument)
> >                 fail: v4l2-test-buffers.cpp(571): q.has_expbuf(node)
> >                 test VIDIOC_EXPBUF: FAIL
> >
> >To me, this looks like a bug in v4l2-compliance (I'm using 1.10.0).
> >I'm not sure what buffer VIDIOC_EXPBUF is expected to export, since
> >afaics no buffers have been allocated, so of course it's going to fail.
> >Either that, or the v4l2 core vb2 code is non-compliant with v4l2's
> >interface requirements.
> >
> >In any case, it doesn't look like the buffer management is being
> >tested at all by v4l2-compliance - we know that gstreamer works, so
> >buffers _can_ be allocated, and I've also used dmabufs with gstreamer,
> >so I also know that VIDIOC_EXPBUF works there.
> >
> 
> I wouldn't be surprised if you hit on a bug in v4l2-compliance. I stopped
> with v4l2-compliance
> at a different test failure that also didn't make sense to me:

It isn't - the problem is that the results are misleading.  The
VIDIOC_REQBUFS depends on the GET_FMT test succeeding, so it knows
which buffer formats are valid.

Since the GET_FMT test fails due to the colorspace issue, it decides
that it can't trust the format, so it ends up with no formats to test.
This causes the "VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF" test to pass,
but then it moves on to testing "VIDIOC_EXPBUF" with no available
buffers, which then fails.

Fixing GET_FMT (which I've done locally) to return proper colorspace
information results in GET_FMT passing, and also solves the EXPBUF
problem too.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 19, 2017 at 10:54:22AM -0700, Steve Longerbeam wrote:
> 
> 
> On 03/19/2017 03:38 AM, Russell King - ARM Linux wrote:
> >On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> >>Right, imx-media-capture.c (the "standard" v4l2 user interface module)
> >>is not implementing VIDIOC_ENUM_FRAMESIZES. It should, but it can only
> >>return the single frame size that the pipeline has configured (the mbus
> >>format of the attached source pad).
> >I now have a set of patches that enumerate the frame sizes and intervals
> >from the source pad of the first subdev (since you're setting the formats
> >etc there from the capture device, it seems sensible to return what it
> >can support.)  This means my patch set doesn't add to non-CSI subdevs.
> >
> >>Can you share your gstreamer pipeline? For now, until
> >>VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
> >>does not attempt to specify a frame rate. I use the attached
> >>script for testing, which works for me.
> >Note that I'm not specifying a frame rate on gstreamer - I'm setting
> >the pipeline up for 60fps, but gstreamer in its wisdom is unable to
> >enumerate the frame sizes, and therefore is unable to enumerate the
> >frame intervals (frame intervals depend on frame sizes), so it
> >falls back to the "tvnorms" which are basically 25/1 and 30000/1001.
> >
> >It sees 60fps via G_PARM, and then decides to set 30000/1001 via S_PARM.
> >So, we end up with most of the pipeline operating at 60fps, with CSI
> >doing frame skipping to reduce the frame rate to 30fps.
> >
> >gstreamer doesn't complain, doesn't issue any warnings, the only way
> >you can spot this is to enable debugging and look through the copious
> >debug log, or use -v and check the pad capabilities.
> >
> >Testing using gstreamer, and only using "does it produce video" is a
> >good simple test, but it's just that - it's a simple test.  It doesn't
> >tell you that what you're seeing is what you intended to see (such as
> >video at the frame rate you expected) without more work.
> >
> >>Thanks, I've fixed most of v4l2-compliance issues, but this is not
> >>done yet. Is that something you can help with?
> >What did you do with:
> >
> >ioctl(3, VIDIOC_REQBUFS, {count=0, type=0 /* V4L2_BUF_TYPE_??? */, memory=0 /* V4L2_MEMORY_??? */}) = -1 EINVAL (Invalid argument)
> >                 test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
> >ioctl(3, VIDIOC_EXPBUF, 0xbef405bc)     = -1 EINVAL (Invalid argument)
> >                 fail: v4l2-test-buffers.cpp(571): q.has_expbuf(node)
> >                 test VIDIOC_EXPBUF: FAIL
> >
> >To me, this looks like a bug in v4l2-compliance (I'm using 1.10.0).
> >I'm not sure what buffer VIDIOC_EXPBUF is expected to export, since
> >afaics no buffers have been allocated, so of course it's going to fail.
> >Either that, or the v4l2 core vb2 code is non-compliant with v4l2's
> >interface requirements.
> >
> >In any case, it doesn't look like the buffer management is being
> >tested at all by v4l2-compliance - we know that gstreamer works, so
> >buffers _can_ be allocated, and I've also used dmabufs with gstreamer,
> >so I also know that VIDIOC_EXPBUF works there.
> >
> 
> I wouldn't be surprised if you hit on a bug in v4l2-compliance. I stopped
> with v4l2-compliance
> at a different test failure that also didn't make sense to me:

It isn't - the problem is that the results are misleading.  The
VIDIOC_REQBUFS depends on the GET_FMT test succeeding, so it knows
which buffer formats are valid.

Since the GET_FMT test fails due to the colorspace issue, it decides
that it can't trust the format, so it ends up with no formats to test.
This causes the "VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF" test to pass,
but then it moves on to testing "VIDIOC_EXPBUF" with no available
buffers, which then fails.

Fixing GET_FMT (which I've done locally) to return proper colorspace
information results in GET_FMT passing, and also solves the EXPBUF
problem too.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Hans Verkuil]

On 03/19/2017 06:54 PM, Steve Longerbeam wrote:
> 
> 
> On 03/19/2017 03:38 AM, Russell King - ARM Linux wrote:
>> On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
>>> Right, imx-media-capture.c (the "standard" v4l2 user interface module)
>>> is not implementing VIDIOC_ENUM_FRAMESIZES. It should, but it can only
>>> return the single frame size that the pipeline has configured (the mbus
>>> format of the attached source pad).
>> I now have a set of patches that enumerate the frame sizes and intervals
>> from the source pad of the first subdev (since you're setting the formats
>> etc there from the capture device, it seems sensible to return what it
>> can support.)  This means my patch set doesn't add to non-CSI subdevs.
>>
>>> Can you share your gstreamer pipeline? For now, until
>>> VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
>>> does not attempt to specify a frame rate. I use the attached
>>> script for testing, which works for me.
>> Note that I'm not specifying a frame rate on gstreamer - I'm setting
>> the pipeline up for 60fps, but gstreamer in its wisdom is unable to
>> enumerate the frame sizes, and therefore is unable to enumerate the
>> frame intervals (frame intervals depend on frame sizes), so it
>> falls back to the "tvnorms" which are basically 25/1 and 30000/1001.
>>
>> It sees 60fps via G_PARM, and then decides to set 30000/1001 via S_PARM.
>> So, we end up with most of the pipeline operating at 60fps, with CSI
>> doing frame skipping to reduce the frame rate to 30fps.
>>
>> gstreamer doesn't complain, doesn't issue any warnings, the only way
>> you can spot this is to enable debugging and look through the copious
>> debug log, or use -v and check the pad capabilities.
>>
>> Testing using gstreamer, and only using "does it produce video" is a
>> good simple test, but it's just that - it's a simple test.  It doesn't
>> tell you that what you're seeing is what you intended to see (such as
>> video at the frame rate you expected) without more work.
>>
>>> Thanks, I've fixed most of v4l2-compliance issues, but this is not
>>> done yet. Is that something you can help with?
>> What did you do with:
>>
>> ioctl(3, VIDIOC_REQBUFS, {count=0, type=0 /* V4L2_BUF_TYPE_??? */, memory=0 /* V4L2_MEMORY_??? */}) = -1 EINVAL (Invalid argument)
>>                  test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
>> ioctl(3, VIDIOC_EXPBUF, 0xbef405bc)     = -1 EINVAL (Invalid argument)
>>                  fail: v4l2-test-buffers.cpp(571): q.has_expbuf(node)

This is really a knock-on effect from an earlier issue where the compliance test
didn't detect support for MEMORY_MMAP.

>>                  test VIDIOC_EXPBUF: FAIL
>>
>> To me, this looks like a bug in v4l2-compliance (I'm using 1.10.0).

Always build from the master repo. 1.10 is pretty old.

>> I'm not sure what buffer VIDIOC_EXPBUF is expected to export, since
>> afaics no buffers have been allocated, so of course it's going to fail.

It just tests if EXPBUF is supported.

I think I will modify v4l2-compliance to bail out if it doesn't find support
for MEMORY_MMAP. Even though in theory support for this is optional, in practice
all applications expect that it is supported. That should fix this
hard-to-understand error.

>> Either that, or the v4l2 core vb2 code is non-compliant with v4l2's
>> interface requirements.
>>
>> In any case, it doesn't look like the buffer management is being
>> tested at all by v4l2-compliance - we know that gstreamer works, so
>> buffers _can_ be allocated, and I've also used dmabufs with gstreamer,
>> so I also know that VIDIOC_EXPBUF works there.

To test actual streaming you need to provide the -s option.

Note: v4l2-compliance has been developed for 'regular' video devices,
not MC devices. It may or may not work with the -s option.

As I think I mentioned somewhere else, creating a compliance test for
MC devices would help enormously in verifying drivers. I'm not sure if
it is better to create a new test or integrate it in v4l2-compliance.

I'm leaning towards the latter since there is a lot of overlap.

>>
> 
> I wouldn't be surprised if you hit on a bug in v4l2-compliance. I 
> stopped with v4l2-compliance
> at a different test failure that also didn't make sense to me:
> 
> Streaming ioctls:
>      test read/write: OK (Not Supported)
>          Video Capture:
>          Buffer: 0 Sequence: 0 Field: Any Timestamp: 41.664259s
>          fail: 
> .../v4l-utils-1.6.2/utils/v4l2-compliance/v4l2-test-buffers.cpp(281): 
> !(g_flags() & (V4L2_BUF_FLAG_DONE | V4L2_BUF_FLAG_ERROR))
>          fail: 
> .../v4l-utils-1.6.2/utils/v4l2-compliance/v4l2-test-buffers.cpp(610): 
> buf.check(q, last_seq)
>          fail: 
> .../v4l-utils-1.6.2/utils/v4l2-compliance/v4l2-test-buffers.cpp(883): 
> captureBufs(node, q, m2m_q, frame_count, false)
>      test MMAP: FAIL
>      test USERPTR: OK (Not Supported)
>      test DMABUF: Cannot test, specify --expbuf-device
> 
> Total: 42, Succeeded: 38, Failed: 4, Warnings: 0
> 
> 
> In this case the driver completed and returned only one buffer, and it set
> VB2_BUF_STATE_DONE, so these test failures didn't make sense to me. I
> was using version 1.6.2 at the time.

I can't do anything with that. Always use the master branch in the v4l-utils
repo.

Regards,

	Hans

[PATCH v5 00/39] i.MX Media Driver

[Hans Verkuil]

On 03/19/2017 06:54 PM, Steve Longerbeam wrote:
> 
> 
> On 03/19/2017 03:38 AM, Russell King - ARM Linux wrote:
>> On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
>>> Right, imx-media-capture.c (the "standard" v4l2 user interface module)
>>> is not implementing VIDIOC_ENUM_FRAMESIZES. It should, but it can only
>>> return the single frame size that the pipeline has configured (the mbus
>>> format of the attached source pad).
>> I now have a set of patches that enumerate the frame sizes and intervals
>> from the source pad of the first subdev (since you're setting the formats
>> etc there from the capture device, it seems sensible to return what it
>> can support.)  This means my patch set doesn't add to non-CSI subdevs.
>>
>>> Can you share your gstreamer pipeline? For now, until
>>> VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
>>> does not attempt to specify a frame rate. I use the attached
>>> script for testing, which works for me.
>> Note that I'm not specifying a frame rate on gstreamer - I'm setting
>> the pipeline up for 60fps, but gstreamer in its wisdom is unable to
>> enumerate the frame sizes, and therefore is unable to enumerate the
>> frame intervals (frame intervals depend on frame sizes), so it
>> falls back to the "tvnorms" which are basically 25/1 and 30000/1001.
>>
>> It sees 60fps via G_PARM, and then decides to set 30000/1001 via S_PARM.
>> So, we end up with most of the pipeline operating at 60fps, with CSI
>> doing frame skipping to reduce the frame rate to 30fps.
>>
>> gstreamer doesn't complain, doesn't issue any warnings, the only way
>> you can spot this is to enable debugging and look through the copious
>> debug log, or use -v and check the pad capabilities.
>>
>> Testing using gstreamer, and only using "does it produce video" is a
>> good simple test, but it's just that - it's a simple test.  It doesn't
>> tell you that what you're seeing is what you intended to see (such as
>> video at the frame rate you expected) without more work.
>>
>>> Thanks, I've fixed most of v4l2-compliance issues, but this is not
>>> done yet. Is that something you can help with?
>> What did you do with:
>>
>> ioctl(3, VIDIOC_REQBUFS, {count=0, type=0 /* V4L2_BUF_TYPE_??? */, memory=0 /* V4L2_MEMORY_??? */}) = -1 EINVAL (Invalid argument)
>>                  test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
>> ioctl(3, VIDIOC_EXPBUF, 0xbef405bc)     = -1 EINVAL (Invalid argument)
>>                  fail: v4l2-test-buffers.cpp(571): q.has_expbuf(node)

This is really a knock-on effect from an earlier issue where the compliance test
didn't detect support for MEMORY_MMAP.

>>                  test VIDIOC_EXPBUF: FAIL
>>
>> To me, this looks like a bug in v4l2-compliance (I'm using 1.10.0).

Always build from the master repo. 1.10 is pretty old.

>> I'm not sure what buffer VIDIOC_EXPBUF is expected to export, since
>> afaics no buffers have been allocated, so of course it's going to fail.

It just tests if EXPBUF is supported.

I think I will modify v4l2-compliance to bail out if it doesn't find support
for MEMORY_MMAP. Even though in theory support for this is optional, in practice
all applications expect that it is supported. That should fix this
hard-to-understand error.

>> Either that, or the v4l2 core vb2 code is non-compliant with v4l2's
>> interface requirements.
>>
>> In any case, it doesn't look like the buffer management is being
>> tested at all by v4l2-compliance - we know that gstreamer works, so
>> buffers _can_ be allocated, and I've also used dmabufs with gstreamer,
>> so I also know that VIDIOC_EXPBUF works there.

To test actual streaming you need to provide the -s option.

Note: v4l2-compliance has been developed for 'regular' video devices,
not MC devices. It may or may not work with the -s option.

As I think I mentioned somewhere else, creating a compliance test for
MC devices would help enormously in verifying drivers. I'm not sure if
it is better to create a new test or integrate it in v4l2-compliance.

I'm leaning towards the latter since there is a lot of overlap.

>>
> 
> I wouldn't be surprised if you hit on a bug in v4l2-compliance. I 
> stopped with v4l2-compliance
> at a different test failure that also didn't make sense to me:
> 
> Streaming ioctls:
>      test read/write: OK (Not Supported)
>          Video Capture:
>          Buffer: 0 Sequence: 0 Field: Any Timestamp: 41.664259s
>          fail: 
> .../v4l-utils-1.6.2/utils/v4l2-compliance/v4l2-test-buffers.cpp(281): 
> !(g_flags() & (V4L2_BUF_FLAG_DONE | V4L2_BUF_FLAG_ERROR))
>          fail: 
> .../v4l-utils-1.6.2/utils/v4l2-compliance/v4l2-test-buffers.cpp(610): 
> buf.check(q, last_seq)
>          fail: 
> .../v4l-utils-1.6.2/utils/v4l2-compliance/v4l2-test-buffers.cpp(883): 
> captureBufs(node, q, m2m_q, frame_count, false)
>      test MMAP: FAIL
>      test USERPTR: OK (Not Supported)
>      test DMABUF: Cannot test, specify --expbuf-device
> 
> Total: 42, Succeeded: 38, Failed: 4, Warnings: 0
> 
> 
> In this case the driver completed and returned only one buffer, and it set
> VB2_BUF_STATE_DONE, so these test failures didn't make sense to me. I
> was using version 1.6.2 at the time.

I can't do anything with that. Always use the master branch in the v4l-utils
repo.

Regards,

	Hans

Re: [PATCH v5 00/39] i.MX Media Driver

[Hans Verkuil]

On 03/19/2017 06:54 PM, Steve Longerbeam wrote:
> 
> 
> On 03/19/2017 03:38 AM, Russell King - ARM Linux wrote:
>> On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
>>> Right, imx-media-capture.c (the "standard" v4l2 user interface module)
>>> is not implementing VIDIOC_ENUM_FRAMESIZES. It should, but it can only
>>> return the single frame size that the pipeline has configured (the mbus
>>> format of the attached source pad).
>> I now have a set of patches that enumerate the frame sizes and intervals
>> from the source pad of the first subdev (since you're setting the formats
>> etc there from the capture device, it seems sensible to return what it
>> can support.)  This means my patch set doesn't add to non-CSI subdevs.
>>
>>> Can you share your gstreamer pipeline? For now, until
>>> VIDIOC_ENUM_FRAMESIZES is implemented, try a pipeline that
>>> does not attempt to specify a frame rate. I use the attached
>>> script for testing, which works for me.
>> Note that I'm not specifying a frame rate on gstreamer - I'm setting
>> the pipeline up for 60fps, but gstreamer in its wisdom is unable to
>> enumerate the frame sizes, and therefore is unable to enumerate the
>> frame intervals (frame intervals depend on frame sizes), so it
>> falls back to the "tvnorms" which are basically 25/1 and 30000/1001.
>>
>> It sees 60fps via G_PARM, and then decides to set 30000/1001 via S_PARM.
>> So, we end up with most of the pipeline operating at 60fps, with CSI
>> doing frame skipping to reduce the frame rate to 30fps.
>>
>> gstreamer doesn't complain, doesn't issue any warnings, the only way
>> you can spot this is to enable debugging and look through the copious
>> debug log, or use -v and check the pad capabilities.
>>
>> Testing using gstreamer, and only using "does it produce video" is a
>> good simple test, but it's just that - it's a simple test.  It doesn't
>> tell you that what you're seeing is what you intended to see (such as
>> video at the frame rate you expected) without more work.
>>
>>> Thanks, I've fixed most of v4l2-compliance issues, but this is not
>>> done yet. Is that something you can help with?
>> What did you do with:
>>
>> ioctl(3, VIDIOC_REQBUFS, {count=0, type=0 /* V4L2_BUF_TYPE_??? */, memory=0 /* V4L2_MEMORY_??? */}) = -1 EINVAL (Invalid argument)
>>                  test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
>> ioctl(3, VIDIOC_EXPBUF, 0xbef405bc)     = -1 EINVAL (Invalid argument)
>>                  fail: v4l2-test-buffers.cpp(571): q.has_expbuf(node)

This is really a knock-on effect from an earlier issue where the compliance test
didn't detect support for MEMORY_MMAP.

>>                  test VIDIOC_EXPBUF: FAIL
>>
>> To me, this looks like a bug in v4l2-compliance (I'm using 1.10.0).

Always build from the master repo. 1.10 is pretty old.

>> I'm not sure what buffer VIDIOC_EXPBUF is expected to export, since
>> afaics no buffers have been allocated, so of course it's going to fail.

It just tests if EXPBUF is supported.

I think I will modify v4l2-compliance to bail out if it doesn't find support
for MEMORY_MMAP. Even though in theory support for this is optional, in practice
all applications expect that it is supported. That should fix this
hard-to-understand error.

>> Either that, or the v4l2 core vb2 code is non-compliant with v4l2's
>> interface requirements.
>>
>> In any case, it doesn't look like the buffer management is being
>> tested at all by v4l2-compliance - we know that gstreamer works, so
>> buffers _can_ be allocated, and I've also used dmabufs with gstreamer,
>> so I also know that VIDIOC_EXPBUF works there.

To test actual streaming you need to provide the -s option.

Note: v4l2-compliance has been developed for 'regular' video devices,
not MC devices. It may or may not work with the -s option.

As I think I mentioned somewhere else, creating a compliance test for
MC devices would help enormously in verifying drivers. I'm not sure if
it is better to create a new test or integrate it in v4l2-compliance.

I'm leaning towards the latter since there is a lot of overlap.

>>
> 
> I wouldn't be surprised if you hit on a bug in v4l2-compliance. I 
> stopped with v4l2-compliance
> at a different test failure that also didn't make sense to me:
> 
> Streaming ioctls:
>      test read/write: OK (Not Supported)
>          Video Capture:
>          Buffer: 0 Sequence: 0 Field: Any Timestamp: 41.664259s
>          fail: 
> .../v4l-utils-1.6.2/utils/v4l2-compliance/v4l2-test-buffers.cpp(281): 
> !(g_flags() & (V4L2_BUF_FLAG_DONE | V4L2_BUF_FLAG_ERROR))
>          fail: 
> .../v4l-utils-1.6.2/utils/v4l2-compliance/v4l2-test-buffers.cpp(610): 
> buf.check(q, last_seq)
>          fail: 
> .../v4l-utils-1.6.2/utils/v4l2-compliance/v4l2-test-buffers.cpp(883): 
> captureBufs(node, q, m2m_q, frame_count, false)
>      test MMAP: FAIL
>      test USERPTR: OK (Not Supported)
>      test DMABUF: Cannot test, specify --expbuf-device
> 
> Total: 42, Succeeded: 38, Failed: 4, Warnings: 0
> 
> 
> In this case the driver completed and returned only one buffer, and it set
> VB2_BUF_STATE_DONE, so these test failures didn't make sense to me. I
> was using version 1.6.2 at the time.

I can't do anything with that. Always use the master branch in the v4l-utils
repo.

Regards,

	Hans

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 02:01:58PM +0100, Hans Verkuil wrote:
> On 03/19/2017 06:54 PM, Steve Longerbeam wrote:
> > 
> > 
> > On 03/19/2017 03:38 AM, Russell King - ARM Linux wrote:
> >> What did you do with:
> >>
> >> ioctl(3, VIDIOC_REQBUFS, {count=0, type=0 /* V4L2_BUF_TYPE_??? */, memory=0 /* V4L2_MEMORY_??? */}) = -1 EINVAL (Invalid argument)
> >>                  test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
> >> ioctl(3, VIDIOC_EXPBUF, 0xbef405bc)     = -1 EINVAL (Invalid argument)
> >>                  fail: v4l2-test-buffers.cpp(571): q.has_expbuf(node)
> 
> This is really a knock-on effect from an earlier issue where the compliance test
> didn't detect support for MEMORY_MMAP.

So why does it succeed when I fix the compliance errors with VIDIOC_G_FMT?
With that fixed, I now get:

        Format ioctls:
                test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
                test VIDIOC_G/S_PARM: OK
                test VIDIOC_G_FBUF: OK (Not Supported)
                test VIDIOC_G_FMT: OK
                test VIDIOC_TRY_FMT: OK
                test VIDIOC_S_FMT: OK
                test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
                test Cropping: OK (Not Supported)
                test Composing: OK (Not Supported)
                test Scaling: OK (Not Supported)

        Buffer ioctls:
                test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
                test VIDIOC_EXPBUF: OK

The reason is, if you look at the code, VIDIOC_G_FMT populates a list
of possible buffer formats "node->valid_buftypes".  If the VIDIOC_G_FMT
test fails, then node->valid_buftypes is zero.

This causes testReqBufs() to only check for the all-zeroed VIDIOC_REQBUFS
and declare it conformant, without creating any buffers (it can't, it
doesn't know which formats are supported.)

This causes node->valid_memorytype to be zero.

We then go on to testExpBuf(), and valid_memorytype zero, claiming (falsely)
that MMAP is not supported.  The reality is that it _is_ supported, but
it's just the non-compliant VICIOC_G_FMT call (due to the colorspace
issue) causes the sequence of tests to fail.

> Always build from the master repo. 1.10 is pretty old.

It's what I have - remember, not everyone is happy to constantly replace
their distro packages with random new stuff.

> >> In any case, it doesn't look like the buffer management is being
> >> tested at all by v4l2-compliance - we know that gstreamer works, so
> >> buffers _can_ be allocated, and I've also used dmabufs with gstreamer,
> >> so I also know that VIDIOC_EXPBUF works there.
> 
> To test actual streaming you need to provide the -s option.
> 
> Note: v4l2-compliance has been developed for 'regular' video devices,
> not MC devices. It may or may not work with the -s option.

Right, and it exists to verify that the establised v4l2 API is correctly
implemented.  If the v4l2 API is being offered to user applications,
then it must be conformant, otherwise it's not offering the v4l2 API.
(That's very much a definition statement in itself.)

So, are we really going to say MC devices do not offer the v4l2 API to
userspace, but something that might work?  We've already seen today
one user say that they're not going to use mainline because of the
crud surrounding MC.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 02:01:58PM +0100, Hans Verkuil wrote:
> On 03/19/2017 06:54 PM, Steve Longerbeam wrote:
> > 
> > 
> > On 03/19/2017 03:38 AM, Russell King - ARM Linux wrote:
> >> What did you do with:
> >>
> >> ioctl(3, VIDIOC_REQBUFS, {count=0, type=0 /* V4L2_BUF_TYPE_??? */, memory=0 /* V4L2_MEMORY_??? */}) = -1 EINVAL (Invalid argument)
> >>                  test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
> >> ioctl(3, VIDIOC_EXPBUF, 0xbef405bc)     = -1 EINVAL (Invalid argument)
> >>                  fail: v4l2-test-buffers.cpp(571): q.has_expbuf(node)
> 
> This is really a knock-on effect from an earlier issue where the compliance test
> didn't detect support for MEMORY_MMAP.

So why does it succeed when I fix the compliance errors with VIDIOC_G_FMT?
With that fixed, I now get:

        Format ioctls:
                test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
                test VIDIOC_G/S_PARM: OK
                test VIDIOC_G_FBUF: OK (Not Supported)
                test VIDIOC_G_FMT: OK
                test VIDIOC_TRY_FMT: OK
                test VIDIOC_S_FMT: OK
                test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
                test Cropping: OK (Not Supported)
                test Composing: OK (Not Supported)
                test Scaling: OK (Not Supported)

        Buffer ioctls:
                test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
                test VIDIOC_EXPBUF: OK

The reason is, if you look at the code, VIDIOC_G_FMT populates a list
of possible buffer formats "node->valid_buftypes".  If the VIDIOC_G_FMT
test fails, then node->valid_buftypes is zero.

This causes testReqBufs() to only check for the all-zeroed VIDIOC_REQBUFS
and declare it conformant, without creating any buffers (it can't, it
doesn't know which formats are supported.)

This causes node->valid_memorytype to be zero.

We then go on to testExpBuf(), and valid_memorytype zero, claiming (falsely)
that MMAP is not supported.  The reality is that it _is_ supported, but
it's just the non-compliant VICIOC_G_FMT call (due to the colorspace
issue) causes the sequence of tests to fail.

> Always build from the master repo. 1.10 is pretty old.

It's what I have - remember, not everyone is happy to constantly replace
their distro packages with random new stuff.

> >> In any case, it doesn't look like the buffer management is being
> >> tested at all by v4l2-compliance - we know that gstreamer works, so
> >> buffers _can_ be allocated, and I've also used dmabufs with gstreamer,
> >> so I also know that VIDIOC_EXPBUF works there.
> 
> To test actual streaming you need to provide the -s option.
> 
> Note: v4l2-compliance has been developed for 'regular' video devices,
> not MC devices. It may or may not work with the -s option.

Right, and it exists to verify that the establised v4l2 API is correctly
implemented.  If the v4l2 API is being offered to user applications,
then it must be conformant, otherwise it's not offering the v4l2 API.
(That's very much a definition statement in itself.)

So, are we really going to say MC devices do not offer the v4l2 API to
userspace, but something that might work?  We've already seen today
one user say that they're not going to use mainline because of the
crud surrounding MC.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 02:01:58PM +0100, Hans Verkuil wrote:
> On 03/19/2017 06:54 PM, Steve Longerbeam wrote:
> > 
> > 
> > On 03/19/2017 03:38 AM, Russell King - ARM Linux wrote:
> >> What did you do with:
> >>
> >> ioctl(3, VIDIOC_REQBUFS, {count=0, type=0 /* V4L2_BUF_TYPE_??? */, memory=0 /* V4L2_MEMORY_??? */}) = -1 EINVAL (Invalid argument)
> >>                  test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
> >> ioctl(3, VIDIOC_EXPBUF, 0xbef405bc)     = -1 EINVAL (Invalid argument)
> >>                  fail: v4l2-test-buffers.cpp(571): q.has_expbuf(node)
> 
> This is really a knock-on effect from an earlier issue where the compliance test
> didn't detect support for MEMORY_MMAP.

So why does it succeed when I fix the compliance errors with VIDIOC_G_FMT?
With that fixed, I now get:

        Format ioctls:
                test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
                test VIDIOC_G/S_PARM: OK
                test VIDIOC_G_FBUF: OK (Not Supported)
                test VIDIOC_G_FMT: OK
                test VIDIOC_TRY_FMT: OK
                test VIDIOC_S_FMT: OK
                test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
                test Cropping: OK (Not Supported)
                test Composing: OK (Not Supported)
                test Scaling: OK (Not Supported)

        Buffer ioctls:
                test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
                test VIDIOC_EXPBUF: OK

The reason is, if you look at the code, VIDIOC_G_FMT populates a list
of possible buffer formats "node->valid_buftypes".  If the VIDIOC_G_FMT
test fails, then node->valid_buftypes is zero.

This causes testReqBufs() to only check for the all-zeroed VIDIOC_REQBUFS
and declare it conformant, without creating any buffers (it can't, it
doesn't know which formats are supported.)

This causes node->valid_memorytype to be zero.

We then go on to testExpBuf(), and valid_memorytype zero, claiming (falsely)
that MMAP is not supported.  The reality is that it _is_ supported, but
it's just the non-compliant VICIOC_G_FMT call (due to the colorspace
issue) causes the sequence of tests to fail.

> Always build from the master repo. 1.10 is pretty old.

It's what I have - remember, not everyone is happy to constantly replace
their distro packages with random new stuff.

> >> In any case, it doesn't look like the buffer management is being
> >> tested at all by v4l2-compliance - we know that gstreamer works, so
> >> buffers _can_ be allocated, and I've also used dmabufs with gstreamer,
> >> so I also know that VIDIOC_EXPBUF works there.
> 
> To test actual streaming you need to provide the -s option.
> 
> Note: v4l2-compliance has been developed for 'regular' video devices,
> not MC devices. It may or may not work with the -s option.

Right, and it exists to verify that the establised v4l2 API is correctly
implemented.  If the v4l2 API is being offered to user applications,
then it must be conformant, otherwise it's not offering the v4l2 API.
(That's very much a definition statement in itself.)

So, are we really going to say MC devices do not offer the v4l2 API to
userspace, but something that might work?  We've already seen today
one user say that they're not going to use mainline because of the
crud surrounding MC.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Hans Verkuil]

On 03/20/2017 02:29 PM, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 02:01:58PM +0100, Hans Verkuil wrote:
>> On 03/19/2017 06:54 PM, Steve Longerbeam wrote:
>>>
>>>
>>> On 03/19/2017 03:38 AM, Russell King - ARM Linux wrote:
>>>> What did you do with:
>>>>
>>>> ioctl(3, VIDIOC_REQBUFS, {count=0, type=0 /* V4L2_BUF_TYPE_??? */, memory=0 /* V4L2_MEMORY_??? */}) = -1 EINVAL (Invalid argument)
>>>>                  test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
>>>> ioctl(3, VIDIOC_EXPBUF, 0xbef405bc)     = -1 EINVAL (Invalid argument)
>>>>                  fail: v4l2-test-buffers.cpp(571): q.has_expbuf(node)
>>
>> This is really a knock-on effect from an earlier issue where the compliance test
>> didn't detect support for MEMORY_MMAP.
> 
> So why does it succeed when I fix the compliance errors with VIDIOC_G_FMT?
> With that fixed, I now get:
> 
>         Format ioctls:
>                 test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
>                 test VIDIOC_G/S_PARM: OK
>                 test VIDIOC_G_FBUF: OK (Not Supported)
>                 test VIDIOC_G_FMT: OK
>                 test VIDIOC_TRY_FMT: OK
>                 test VIDIOC_S_FMT: OK
>                 test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
>                 test Cropping: OK (Not Supported)
>                 test Composing: OK (Not Supported)
>                 test Scaling: OK (Not Supported)
> 
>         Buffer ioctls:
>                 test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
>                 test VIDIOC_EXPBUF: OK
> 
> The reason is, if you look at the code, VIDIOC_G_FMT populates a list
> of possible buffer formats "node->valid_buftypes".  If the VIDIOC_G_FMT
> test fails, then node->valid_buftypes is zero.
> 
> This causes testReqBufs() to only check for the all-zeroed VIDIOC_REQBUFS
> and declare it conformant, without creating any buffers (it can't, it
> doesn't know which formats are supported.)
> 
> This causes node->valid_memorytype to be zero.

It should fail on this and return a more understandable error message.

> 
> We then go on to testExpBuf(), and valid_memorytype zero, claiming (falsely)
> that MMAP is not supported.  The reality is that it _is_ supported, but
> it's just the non-compliant VICIOC_G_FMT call (due to the colorspace
> issue) causes the sequence of tests to fail.

Yeah, you're not the first to complain about this. I plan on fixing this this
week.

> 
>> Always build from the master repo. 1.10 is pretty old.
> 
> It's what I have - remember, not everyone is happy to constantly replace
> their distro packages with random new stuff.

This is a compliance test, which is continuously developed in tandem with
new kernel versions. If you are working with an upstream kernel, then you
should also use the corresponding v4l2-compliance test. What's the point
of using an old one?

I will not support driver developers that use an old version of the
compliance test, that's a waste of my time.

> 
>>>> In any case, it doesn't look like the buffer management is being
>>>> tested at all by v4l2-compliance - we know that gstreamer works, so
>>>> buffers _can_ be allocated, and I've also used dmabufs with gstreamer,
>>>> so I also know that VIDIOC_EXPBUF works there.
>>
>> To test actual streaming you need to provide the -s option.
>>
>> Note: v4l2-compliance has been developed for 'regular' video devices,
>> not MC devices. It may or may not work with the -s option.
> 
> Right, and it exists to verify that the establised v4l2 API is correctly
> implemented.  If the v4l2 API is being offered to user applications,
> then it must be conformant, otherwise it's not offering the v4l2 API.
> (That's very much a definition statement in itself.)
> 
> So, are we really going to say MC devices do not offer the v4l2 API to
> userspace, but something that might work?  We've already seen today
> one user say that they're not going to use mainline because of the
> crud surrounding MC.
> 

Actually, my understanding was that he was stuck on the old kernel code.

In the case of v4l2-compliance, I never had the time to make it work with
MC devices. Same for that matter of certain memory to memory devices.

Just like MC devices these too behave differently. They are partially
supported in v4l2-compliance, but not fully.

Why? NO TIME.

Be glad there *is* a v4l2-compliance test at all! It's really, really useful
already, but it took *years* to develop, little bit by little bit. And yes,
I would really like to update it to fully support codecs and MC devices.
And with a bit of luck I hope to get permission from my boss to work on
this (among others) later in the year.

Complaining about this really won't help. We know it's a problem and unless
someone (me perhaps?) manages to get paid to work on this it's unlikely to
change for now.

Regards,

	Hans

[PATCH v5 00/39] i.MX Media Driver

[Hans Verkuil]

On 03/20/2017 02:29 PM, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 02:01:58PM +0100, Hans Verkuil wrote:
>> On 03/19/2017 06:54 PM, Steve Longerbeam wrote:
>>>
>>>
>>> On 03/19/2017 03:38 AM, Russell King - ARM Linux wrote:
>>>> What did you do with:
>>>>
>>>> ioctl(3, VIDIOC_REQBUFS, {count=0, type=0 /* V4L2_BUF_TYPE_??? */, memory=0 /* V4L2_MEMORY_??? */}) = -1 EINVAL (Invalid argument)
>>>>                  test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
>>>> ioctl(3, VIDIOC_EXPBUF, 0xbef405bc)     = -1 EINVAL (Invalid argument)
>>>>                  fail: v4l2-test-buffers.cpp(571): q.has_expbuf(node)
>>
>> This is really a knock-on effect from an earlier issue where the compliance test
>> didn't detect support for MEMORY_MMAP.
> 
> So why does it succeed when I fix the compliance errors with VIDIOC_G_FMT?
> With that fixed, I now get:
> 
>         Format ioctls:
>                 test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
>                 test VIDIOC_G/S_PARM: OK
>                 test VIDIOC_G_FBUF: OK (Not Supported)
>                 test VIDIOC_G_FMT: OK
>                 test VIDIOC_TRY_FMT: OK
>                 test VIDIOC_S_FMT: OK
>                 test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
>                 test Cropping: OK (Not Supported)
>                 test Composing: OK (Not Supported)
>                 test Scaling: OK (Not Supported)
> 
>         Buffer ioctls:
>                 test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
>                 test VIDIOC_EXPBUF: OK
> 
> The reason is, if you look at the code, VIDIOC_G_FMT populates a list
> of possible buffer formats "node->valid_buftypes".  If the VIDIOC_G_FMT
> test fails, then node->valid_buftypes is zero.
> 
> This causes testReqBufs() to only check for the all-zeroed VIDIOC_REQBUFS
> and declare it conformant, without creating any buffers (it can't, it
> doesn't know which formats are supported.)
> 
> This causes node->valid_memorytype to be zero.

It should fail on this and return a more understandable error message.

> 
> We then go on to testExpBuf(), and valid_memorytype zero, claiming (falsely)
> that MMAP is not supported.  The reality is that it _is_ supported, but
> it's just the non-compliant VICIOC_G_FMT call (due to the colorspace
> issue) causes the sequence of tests to fail.

Yeah, you're not the first to complain about this. I plan on fixing this this
week.

> 
>> Always build from the master repo. 1.10 is pretty old.
> 
> It's what I have - remember, not everyone is happy to constantly replace
> their distro packages with random new stuff.

This is a compliance test, which is continuously developed in tandem with
new kernel versions. If you are working with an upstream kernel, then you
should also use the corresponding v4l2-compliance test. What's the point
of using an old one?

I will not support driver developers that use an old version of the
compliance test, that's a waste of my time.

> 
>>>> In any case, it doesn't look like the buffer management is being
>>>> tested at all by v4l2-compliance - we know that gstreamer works, so
>>>> buffers _can_ be allocated, and I've also used dmabufs with gstreamer,
>>>> so I also know that VIDIOC_EXPBUF works there.
>>
>> To test actual streaming you need to provide the -s option.
>>
>> Note: v4l2-compliance has been developed for 'regular' video devices,
>> not MC devices. It may or may not work with the -s option.
> 
> Right, and it exists to verify that the establised v4l2 API is correctly
> implemented.  If the v4l2 API is being offered to user applications,
> then it must be conformant, otherwise it's not offering the v4l2 API.
> (That's very much a definition statement in itself.)
> 
> So, are we really going to say MC devices do not offer the v4l2 API to
> userspace, but something that might work?  We've already seen today
> one user say that they're not going to use mainline because of the
> crud surrounding MC.
> 

Actually, my understanding was that he was stuck on the old kernel code.

In the case of v4l2-compliance, I never had the time to make it work with
MC devices. Same for that matter of certain memory to memory devices.

Just like MC devices these too behave differently. They are partially
supported in v4l2-compliance, but not fully.

Why? NO TIME.

Be glad there *is* a v4l2-compliance test at all! It's really, really useful
already, but it took *years* to develop, little bit by little bit. And yes,
I would really like to update it to fully support codecs and MC devices.
And with a bit of luck I hope to get permission from my boss to work on
this (among others) later in the year.

Complaining about this really won't help. We know it's a problem and unless
someone (me perhaps?) manages to get paid to work on this it's unlikely to
change for now.

Regards,

	Hans

Re: [PATCH v5 00/39] i.MX Media Driver

[Hans Verkuil]

On 03/20/2017 02:29 PM, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 02:01:58PM +0100, Hans Verkuil wrote:
>> On 03/19/2017 06:54 PM, Steve Longerbeam wrote:
>>>
>>>
>>> On 03/19/2017 03:38 AM, Russell King - ARM Linux wrote:
>>>> What did you do with:
>>>>
>>>> ioctl(3, VIDIOC_REQBUFS, {count=0, type=0 /* V4L2_BUF_TYPE_??? */, memory=0 /* V4L2_MEMORY_??? */}) = -1 EINVAL (Invalid argument)
>>>>                  test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
>>>> ioctl(3, VIDIOC_EXPBUF, 0xbef405bc)     = -1 EINVAL (Invalid argument)
>>>>                  fail: v4l2-test-buffers.cpp(571): q.has_expbuf(node)
>>
>> This is really a knock-on effect from an earlier issue where the compliance test
>> didn't detect support for MEMORY_MMAP.
> 
> So why does it succeed when I fix the compliance errors with VIDIOC_G_FMT?
> With that fixed, I now get:
> 
>         Format ioctls:
>                 test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
>                 test VIDIOC_G/S_PARM: OK
>                 test VIDIOC_G_FBUF: OK (Not Supported)
>                 test VIDIOC_G_FMT: OK
>                 test VIDIOC_TRY_FMT: OK
>                 test VIDIOC_S_FMT: OK
>                 test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
>                 test Cropping: OK (Not Supported)
>                 test Composing: OK (Not Supported)
>                 test Scaling: OK (Not Supported)
> 
>         Buffer ioctls:
>                 test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
>                 test VIDIOC_EXPBUF: OK
> 
> The reason is, if you look at the code, VIDIOC_G_FMT populates a list
> of possible buffer formats "node->valid_buftypes".  If the VIDIOC_G_FMT
> test fails, then node->valid_buftypes is zero.
> 
> This causes testReqBufs() to only check for the all-zeroed VIDIOC_REQBUFS
> and declare it conformant, without creating any buffers (it can't, it
> doesn't know which formats are supported.)
> 
> This causes node->valid_memorytype to be zero.

It should fail on this and return a more understandable error message.

> 
> We then go on to testExpBuf(), and valid_memorytype zero, claiming (falsely)
> that MMAP is not supported.  The reality is that it _is_ supported, but
> it's just the non-compliant VICIOC_G_FMT call (due to the colorspace
> issue) causes the sequence of tests to fail.

Yeah, you're not the first to complain about this. I plan on fixing this this
week.

> 
>> Always build from the master repo. 1.10 is pretty old.
> 
> It's what I have - remember, not everyone is happy to constantly replace
> their distro packages with random new stuff.

This is a compliance test, which is continuously developed in tandem with
new kernel versions. If you are working with an upstream kernel, then you
should also use the corresponding v4l2-compliance test. What's the point
of using an old one?

I will not support driver developers that use an old version of the
compliance test, that's a waste of my time.

> 
>>>> In any case, it doesn't look like the buffer management is being
>>>> tested at all by v4l2-compliance - we know that gstreamer works, so
>>>> buffers _can_ be allocated, and I've also used dmabufs with gstreamer,
>>>> so I also know that VIDIOC_EXPBUF works there.
>>
>> To test actual streaming you need to provide the -s option.
>>
>> Note: v4l2-compliance has been developed for 'regular' video devices,
>> not MC devices. It may or may not work with the -s option.
> 
> Right, and it exists to verify that the establised v4l2 API is correctly
> implemented.  If the v4l2 API is being offered to user applications,
> then it must be conformant, otherwise it's not offering the v4l2 API.
> (That's very much a definition statement in itself.)
> 
> So, are we really going to say MC devices do not offer the v4l2 API to
> userspace, but something that might work?  We've already seen today
> one user say that they're not going to use mainline because of the
> crud surrounding MC.
> 

Actually, my understanding was that he was stuck on the old kernel code.

In the case of v4l2-compliance, I never had the time to make it work with
MC devices. Same for that matter of certain memory to memory devices.

Just like MC devices these too behave differently. They are partially
supported in v4l2-compliance, but not fully.

Why? NO TIME.

Be glad there *is* a v4l2-compliance test at all! It's really, really useful
already, but it took *years* to develop, little bit by little bit. And yes,
I would really like to update it to fully support codecs and MC devices.
And with a bit of luck I hope to get permission from my boss to work on
this (among others) later in the year.

Complaining about this really won't help. We know it's a problem and unless
someone (me perhaps?) manages to get paid to work on this it's unlikely to
change for now.

Regards,

	Hans

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 02:57:03PM +0100, Hans Verkuil wrote:
> On 03/20/2017 02:29 PM, Russell King - ARM Linux wrote:
> > It's what I have - remember, not everyone is happy to constantly replace
> > their distro packages with random new stuff.
> 
> This is a compliance test, which is continuously developed in tandem with
> new kernel versions. If you are working with an upstream kernel, then you
> should also use the corresponding v4l2-compliance test. What's the point
> of using an old one?
> 
> I will not support driver developers that use an old version of the
> compliance test, that's a waste of my time.

The reason that people may _not_ wish to constantly update v4l-utils
is that it changes the libraries installed on their systems.

So, the solution to that is not to complain about developers not using
the latest version, but instead to de-couple it from the rest of the
package, and provide it as a separate, stand-alone package that doesn't
come with all the extra baggage.

Now, there's two possible answers to that:

1. it depends on the libv4l2 version.  If that's so, then you are
   insisting that people constantly move to the latest libv4l2 because
   of API changes, and those API changes may upset applications they're
   using.  So this isn't really on.

2. it doesn't depend on libv4l2 version, in which case there's no reason
   for it to be packaged with v4l-utils.

The reality is that v4l2-compliance links with libv4l2, so I'm not sure
which it is.  What I am sure of is that I don't want to upgrade libv4l2
on an ad-hoc basis, potentially causing issues with applications.

> >> To test actual streaming you need to provide the -s option.
> >>
> >> Note: v4l2-compliance has been developed for 'regular' video devices,
> >> not MC devices. It may or may not work with the -s option.
> > 
> > Right, and it exists to verify that the establised v4l2 API is correctly
> > implemented.  If the v4l2 API is being offered to user applications,
> > then it must be conformant, otherwise it's not offering the v4l2 API.
> > (That's very much a definition statement in itself.)
> > 
> > So, are we really going to say MC devices do not offer the v4l2 API to
> > userspace, but something that might work?  We've already seen today
> > one user say that they're not going to use mainline because of the
> > crud surrounding MC.
> > 
> 
> Actually, my understanding was that he was stuck on the old kernel code.

Err, sorry, I really don't follow.  Who is "he"?

_I_ was the one who reported the EXPBUF problem.  Your comment makes no
sense.

> In the case of v4l2-compliance, I never had the time to make it work with
> MC devices. Same for that matter of certain memory to memory devices.
> 
> Just like MC devices these too behave differently. They are partially
> supported in v4l2-compliance, but not fully.

It seems you saying that the API provided by /dev/video* for a MC device
breaks the v4l2-compliance tests?

_No one_ has mentioned using v4l2-compliance on the subdevs.

> Complaining about this really won't help. We know it's a problem and unless
> someone (me perhaps?) manages to get paid to work on this it's unlikely to
> change for now.

Like the above comment, your comment makes no sense.  I'm not complaining,
I'm trying to find out the details.

Yes, MC stuff sucks big time right now, the documentation is poor, there's
a lack of understanding on all sides of the issues (which can be seen by
the different opinions that people hold.)  The only way to resolve these
differences is via discussion, and if you're going to start thinking that
everyone is complaining, then there's not going to be any forward progress.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 02:57:03PM +0100, Hans Verkuil wrote:
> On 03/20/2017 02:29 PM, Russell King - ARM Linux wrote:
> > It's what I have - remember, not everyone is happy to constantly replace
> > their distro packages with random new stuff.
> 
> This is a compliance test, which is continuously developed in tandem with
> new kernel versions. If you are working with an upstream kernel, then you
> should also use the corresponding v4l2-compliance test. What's the point
> of using an old one?
> 
> I will not support driver developers that use an old version of the
> compliance test, that's a waste of my time.

The reason that people may _not_ wish to constantly update v4l-utils
is that it changes the libraries installed on their systems.

So, the solution to that is not to complain about developers not using
the latest version, but instead to de-couple it from the rest of the
package, and provide it as a separate, stand-alone package that doesn't
come with all the extra baggage.

Now, there's two possible answers to that:

1. it depends on the libv4l2 version.  If that's so, then you are
   insisting that people constantly move to the latest libv4l2 because
   of API changes, and those API changes may upset applications they're
   using.  So this isn't really on.

2. it doesn't depend on libv4l2 version, in which case there's no reason
   for it to be packaged with v4l-utils.

The reality is that v4l2-compliance links with libv4l2, so I'm not sure
which it is.  What I am sure of is that I don't want to upgrade libv4l2
on an ad-hoc basis, potentially causing issues with applications.

> >> To test actual streaming you need to provide the -s option.
> >>
> >> Note: v4l2-compliance has been developed for 'regular' video devices,
> >> not MC devices. It may or may not work with the -s option.
> > 
> > Right, and it exists to verify that the establised v4l2 API is correctly
> > implemented.  If the v4l2 API is being offered to user applications,
> > then it must be conformant, otherwise it's not offering the v4l2 API.
> > (That's very much a definition statement in itself.)
> > 
> > So, are we really going to say MC devices do not offer the v4l2 API to
> > userspace, but something that might work?  We've already seen today
> > one user say that they're not going to use mainline because of the
> > crud surrounding MC.
> > 
> 
> Actually, my understanding was that he was stuck on the old kernel code.

Err, sorry, I really don't follow.  Who is "he"?

_I_ was the one who reported the EXPBUF problem.  Your comment makes no
sense.

> In the case of v4l2-compliance, I never had the time to make it work with
> MC devices. Same for that matter of certain memory to memory devices.
> 
> Just like MC devices these too behave differently. They are partially
> supported in v4l2-compliance, but not fully.

It seems you saying that the API provided by /dev/video* for a MC device
breaks the v4l2-compliance tests?

_No one_ has mentioned using v4l2-compliance on the subdevs.

> Complaining about this really won't help. We know it's a problem and unless
> someone (me perhaps?) manages to get paid to work on this it's unlikely to
> change for now.

Like the above comment, your comment makes no sense.  I'm not complaining,
I'm trying to find out the details.

Yes, MC stuff sucks big time right now, the documentation is poor, there's
a lack of understanding on all sides of the issues (which can be seen by
the different opinions that people hold.)  The only way to resolve these
differences is via discussion, and if you're going to start thinking that
everyone is complaining, then there's not going to be any forward progress.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 02:57:03PM +0100, Hans Verkuil wrote:
> On 03/20/2017 02:29 PM, Russell King - ARM Linux wrote:
> > It's what I have - remember, not everyone is happy to constantly replace
> > their distro packages with random new stuff.
> 
> This is a compliance test, which is continuously developed in tandem with
> new kernel versions. If you are working with an upstream kernel, then you
> should also use the corresponding v4l2-compliance test. What's the point
> of using an old one?
> 
> I will not support driver developers that use an old version of the
> compliance test, that's a waste of my time.

The reason that people may _not_ wish to constantly update v4l-utils
is that it changes the libraries installed on their systems.

So, the solution to that is not to complain about developers not using
the latest version, but instead to de-couple it from the rest of the
package, and provide it as a separate, stand-alone package that doesn't
come with all the extra baggage.

Now, there's two possible answers to that:

1. it depends on the libv4l2 version.  If that's so, then you are
   insisting that people constantly move to the latest libv4l2 because
   of API changes, and those API changes may upset applications they're
   using.  So this isn't really on.

2. it doesn't depend on libv4l2 version, in which case there's no reason
   for it to be packaged with v4l-utils.

The reality is that v4l2-compliance links with libv4l2, so I'm not sure
which it is.  What I am sure of is that I don't want to upgrade libv4l2
on an ad-hoc basis, potentially causing issues with applications.

> >> To test actual streaming you need to provide the -s option.
> >>
> >> Note: v4l2-compliance has been developed for 'regular' video devices,
> >> not MC devices. It may or may not work with the -s option.
> > 
> > Right, and it exists to verify that the establised v4l2 API is correctly
> > implemented.  If the v4l2 API is being offered to user applications,
> > then it must be conformant, otherwise it's not offering the v4l2 API.
> > (That's very much a definition statement in itself.)
> > 
> > So, are we really going to say MC devices do not offer the v4l2 API to
> > userspace, but something that might work?  We've already seen today
> > one user say that they're not going to use mainline because of the
> > crud surrounding MC.
> > 
> 
> Actually, my understanding was that he was stuck on the old kernel code.

Err, sorry, I really don't follow.  Who is "he"?

_I_ was the one who reported the EXPBUF problem.  Your comment makes no
sense.

> In the case of v4l2-compliance, I never had the time to make it work with
> MC devices. Same for that matter of certain memory to memory devices.
> 
> Just like MC devices these too behave differently. They are partially
> supported in v4l2-compliance, but not fully.

It seems you saying that the API provided by /dev/video* for a MC device
breaks the v4l2-compliance tests?

_No one_ has mentioned using v4l2-compliance on the subdevs.

> Complaining about this really won't help. We know it's a problem and unless
> someone (me perhaps?) manages to get paid to work on this it's unlikely to
> change for now.

Like the above comment, your comment makes no sense.  I'm not complaining,
I'm trying to find out the details.

Yes, MC stuff sucks big time right now, the documentation is poor, there's
a lack of understanding on all sides of the issues (which can be seen by
the different opinions that people hold.)  The only way to resolve these
differences is via discussion, and if you're going to start thinking that
everyone is complaining, then there's not going to be any forward progress.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Hans Verkuil]

On 03/20/2017 03:11 PM, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 02:57:03PM +0100, Hans Verkuil wrote:
>> On 03/20/2017 02:29 PM, Russell King - ARM Linux wrote:
>>> It's what I have - remember, not everyone is happy to constantly replace
>>> their distro packages with random new stuff.
>>
>> This is a compliance test, which is continuously developed in tandem with
>> new kernel versions. If you are working with an upstream kernel, then you
>> should also use the corresponding v4l2-compliance test. What's the point
>> of using an old one?
>>
>> I will not support driver developers that use an old version of the
>> compliance test, that's a waste of my time.
> 
> The reason that people may _not_ wish to constantly update v4l-utils
> is that it changes the libraries installed on their systems.
> 
> So, the solution to that is not to complain about developers not using
> the latest version, but instead to de-couple it from the rest of the
> package, and provide it as a separate, stand-alone package that doesn't
> come with all the extra baggage.
> 
> Now, there's two possible answers to that:
> 
> 1. it depends on the libv4l2 version.  If that's so, then you are
>    insisting that people constantly move to the latest libv4l2 because
>    of API changes, and those API changes may upset applications they're
>    using.  So this isn't really on.
> 
> 2. it doesn't depend on libv4l2 version, in which case there's no reason
>    for it to be packaged with v4l-utils.

Run configure with --disable-v4l2-compliance-libv4l.

This avoids linking with libv4l and allows you to build it stand-alone.

Perhaps I should invert this option since in most cases you don't want to
run v4l2-compliance with libv4l (it's off by default unless you pass the
-w option to v4l2-compliance).

> 
> The reality is that v4l2-compliance links with libv4l2, so I'm not sure
> which it is.  What I am sure of is that I don't want to upgrade libv4l2
> on an ad-hoc basis, potentially causing issues with applications.
> 
>>>> To test actual streaming you need to provide the -s option.
>>>>
>>>> Note: v4l2-compliance has been developed for 'regular' video devices,
>>>> not MC devices. It may or may not work with the -s option.
>>>
>>> Right, and it exists to verify that the establised v4l2 API is correctly
>>> implemented.  If the v4l2 API is being offered to user applications,
>>> then it must be conformant, otherwise it's not offering the v4l2 API.
>>> (That's very much a definition statement in itself.)
>>>
>>> So, are we really going to say MC devices do not offer the v4l2 API to
>>> userspace, but something that might work?  We've already seen today
>>> one user say that they're not going to use mainline because of the
>>> crud surrounding MC.
>>>
>>
>> Actually, my understanding was that he was stuck on the old kernel code.
> 
> Err, sorry, I really don't follow.  Who is "he"?

"one user say that they're not going to use mainline because of the
crud surrounding MC."

> 
> _I_ was the one who reported the EXPBUF problem.  Your comment makes no
> sense.
> 
>> In the case of v4l2-compliance, I never had the time to make it work with
>> MC devices. Same for that matter of certain memory to memory devices.
>>
>> Just like MC devices these too behave differently. They are partially
>> supported in v4l2-compliance, but not fully.
> 
> It seems you saying that the API provided by /dev/video* for a MC device
> breaks the v4l2-compliance tests?

There may be tests in the compliance suite that do not apply for MC devices
and for which I never check. The compliance suite was never written with MC
devices in mind, and it certainly hasn't been tested much with such devices.

It's only very recent that I even got hardware that has MC support...

>From what I can tell from the feedback I got it seems to be OKish, but I
just can't guarantee that the compliance utility is correct for such devices.

In particular I doubt the streaming tests (-s, -f, etc.) will work. The -s
test *might* work if the pipeline is configured correctly before running
v4l2-compliance. I can't imagine that the -f option would work at all since
I would expect pipeline validation errors.

I've been gently pushing Helen Koike to finish her virtual MC driver
(https://patchwork.kernel.org/patch/9312783/) since having a virtual driver
makes writing compliance tests much easier.

> _No one_ has mentioned using v4l2-compliance on the subdevs.
> 
>> Complaining about this really won't help. We know it's a problem and unless
>> someone (me perhaps?) manages to get paid to work on this it's unlikely to
>> change for now.
> 
> Like the above comment, your comment makes no sense.  I'm not complaining,
> I'm trying to find out the details.

Must be me then, it did feel like complaining...

> Yes, MC stuff sucks big time right now, the documentation is poor, there's
> a lack of understanding on all sides of the issues (which can be seen by
> the different opinions that people hold.)  The only way to resolve these
> differences is via discussion, and if you're going to start thinking that
> everyone is complaining, then there's not going to be any forward progress.
> 

Regards,

	Hans

[PATCH v5 00/39] i.MX Media Driver

[Hans Verkuil]

On 03/20/2017 03:11 PM, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 02:57:03PM +0100, Hans Verkuil wrote:
>> On 03/20/2017 02:29 PM, Russell King - ARM Linux wrote:
>>> It's what I have - remember, not everyone is happy to constantly replace
>>> their distro packages with random new stuff.
>>
>> This is a compliance test, which is continuously developed in tandem with
>> new kernel versions. If you are working with an upstream kernel, then you
>> should also use the corresponding v4l2-compliance test. What's the point
>> of using an old one?
>>
>> I will not support driver developers that use an old version of the
>> compliance test, that's a waste of my time.
> 
> The reason that people may _not_ wish to constantly update v4l-utils
> is that it changes the libraries installed on their systems.
> 
> So, the solution to that is not to complain about developers not using
> the latest version, but instead to de-couple it from the rest of the
> package, and provide it as a separate, stand-alone package that doesn't
> come with all the extra baggage.
> 
> Now, there's two possible answers to that:
> 
> 1. it depends on the libv4l2 version.  If that's so, then you are
>    insisting that people constantly move to the latest libv4l2 because
>    of API changes, and those API changes may upset applications they're
>    using.  So this isn't really on.
> 
> 2. it doesn't depend on libv4l2 version, in which case there's no reason
>    for it to be packaged with v4l-utils.

Run configure with --disable-v4l2-compliance-libv4l.

This avoids linking with libv4l and allows you to build it stand-alone.

Perhaps I should invert this option since in most cases you don't want to
run v4l2-compliance with libv4l (it's off by default unless you pass the
-w option to v4l2-compliance).

> 
> The reality is that v4l2-compliance links with libv4l2, so I'm not sure
> which it is.  What I am sure of is that I don't want to upgrade libv4l2
> on an ad-hoc basis, potentially causing issues with applications.
> 
>>>> To test actual streaming you need to provide the -s option.
>>>>
>>>> Note: v4l2-compliance has been developed for 'regular' video devices,
>>>> not MC devices. It may or may not work with the -s option.
>>>
>>> Right, and it exists to verify that the establised v4l2 API is correctly
>>> implemented.  If the v4l2 API is being offered to user applications,
>>> then it must be conformant, otherwise it's not offering the v4l2 API.
>>> (That's very much a definition statement in itself.)
>>>
>>> So, are we really going to say MC devices do not offer the v4l2 API to
>>> userspace, but something that might work?  We've already seen today
>>> one user say that they're not going to use mainline because of the
>>> crud surrounding MC.
>>>
>>
>> Actually, my understanding was that he was stuck on the old kernel code.
> 
> Err, sorry, I really don't follow.  Who is "he"?

"one user say that they're not going to use mainline because of the
crud surrounding MC."

> 
> _I_ was the one who reported the EXPBUF problem.  Your comment makes no
> sense.
> 
>> In the case of v4l2-compliance, I never had the time to make it work with
>> MC devices. Same for that matter of certain memory to memory devices.
>>
>> Just like MC devices these too behave differently. They are partially
>> supported in v4l2-compliance, but not fully.
> 
> It seems you saying that the API provided by /dev/video* for a MC device
> breaks the v4l2-compliance tests?

There may be tests in the compliance suite that do not apply for MC devices
and for which I never check. The compliance suite was never written with MC
devices in mind, and it certainly hasn't been tested much with such devices.

It's only very recent that I even got hardware that has MC support...

>From what I can tell from the feedback I got it seems to be OKish, but I
just can't guarantee that the compliance utility is correct for such devices.

In particular I doubt the streaming tests (-s, -f, etc.) will work. The -s
test *might* work if the pipeline is configured correctly before running
v4l2-compliance. I can't imagine that the -f option would work at all since
I would expect pipeline validation errors.

I've been gently pushing Helen Koike to finish her virtual MC driver
(https://patchwork.kernel.org/patch/9312783/) since having a virtual driver
makes writing compliance tests much easier.

> _No one_ has mentioned using v4l2-compliance on the subdevs.
> 
>> Complaining about this really won't help. We know it's a problem and unless
>> someone (me perhaps?) manages to get paid to work on this it's unlikely to
>> change for now.
> 
> Like the above comment, your comment makes no sense.  I'm not complaining,
> I'm trying to find out the details.

Must be me then, it did feel like complaining...

> Yes, MC stuff sucks big time right now, the documentation is poor, there's
> a lack of understanding on all sides of the issues (which can be seen by
> the different opinions that people hold.)  The only way to resolve these
> differences is via discussion, and if you're going to start thinking that
> everyone is complaining, then there's not going to be any forward progress.
> 

Regards,

	Hans

Re: [PATCH v5 00/39] i.MX Media Driver

[Hans Verkuil]

On 03/20/2017 03:11 PM, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 02:57:03PM +0100, Hans Verkuil wrote:
>> On 03/20/2017 02:29 PM, Russell King - ARM Linux wrote:
>>> It's what I have - remember, not everyone is happy to constantly replace
>>> their distro packages with random new stuff.
>>
>> This is a compliance test, which is continuously developed in tandem with
>> new kernel versions. If you are working with an upstream kernel, then you
>> should also use the corresponding v4l2-compliance test. What's the point
>> of using an old one?
>>
>> I will not support driver developers that use an old version of the
>> compliance test, that's a waste of my time.
> 
> The reason that people may _not_ wish to constantly update v4l-utils
> is that it changes the libraries installed on their systems.
> 
> So, the solution to that is not to complain about developers not using
> the latest version, but instead to de-couple it from the rest of the
> package, and provide it as a separate, stand-alone package that doesn't
> come with all the extra baggage.
> 
> Now, there's two possible answers to that:
> 
> 1. it depends on the libv4l2 version.  If that's so, then you are
>    insisting that people constantly move to the latest libv4l2 because
>    of API changes, and those API changes may upset applications they're
>    using.  So this isn't really on.
> 
> 2. it doesn't depend on libv4l2 version, in which case there's no reason
>    for it to be packaged with v4l-utils.

Run configure with --disable-v4l2-compliance-libv4l.

This avoids linking with libv4l and allows you to build it stand-alone.

Perhaps I should invert this option since in most cases you don't want to
run v4l2-compliance with libv4l (it's off by default unless you pass the
-w option to v4l2-compliance).

> 
> The reality is that v4l2-compliance links with libv4l2, so I'm not sure
> which it is.  What I am sure of is that I don't want to upgrade libv4l2
> on an ad-hoc basis, potentially causing issues with applications.
> 
>>>> To test actual streaming you need to provide the -s option.
>>>>
>>>> Note: v4l2-compliance has been developed for 'regular' video devices,
>>>> not MC devices. It may or may not work with the -s option.
>>>
>>> Right, and it exists to verify that the establised v4l2 API is correctly
>>> implemented.  If the v4l2 API is being offered to user applications,
>>> then it must be conformant, otherwise it's not offering the v4l2 API.
>>> (That's very much a definition statement in itself.)
>>>
>>> So, are we really going to say MC devices do not offer the v4l2 API to
>>> userspace, but something that might work?  We've already seen today
>>> one user say that they're not going to use mainline because of the
>>> crud surrounding MC.
>>>
>>
>> Actually, my understanding was that he was stuck on the old kernel code.
> 
> Err, sorry, I really don't follow.  Who is "he"?

"one user say that they're not going to use mainline because of the
crud surrounding MC."

> 
> _I_ was the one who reported the EXPBUF problem.  Your comment makes no
> sense.
> 
>> In the case of v4l2-compliance, I never had the time to make it work with
>> MC devices. Same for that matter of certain memory to memory devices.
>>
>> Just like MC devices these too behave differently. They are partially
>> supported in v4l2-compliance, but not fully.
> 
> It seems you saying that the API provided by /dev/video* for a MC device
> breaks the v4l2-compliance tests?

There may be tests in the compliance suite that do not apply for MC devices
and for which I never check. The compliance suite was never written with MC
devices in mind, and it certainly hasn't been tested much with such devices.

It's only very recent that I even got hardware that has MC support...

>From what I can tell from the feedback I got it seems to be OKish, but I
just can't guarantee that the compliance utility is correct for such devices.

In particular I doubt the streaming tests (-s, -f, etc.) will work. The -s
test *might* work if the pipeline is configured correctly before running
v4l2-compliance. I can't imagine that the -f option would work at all since
I would expect pipeline validation errors.

I've been gently pushing Helen Koike to finish her virtual MC driver
(https://patchwork.kernel.org/patch/9312783/) since having a virtual driver
makes writing compliance tests much easier.

> _No one_ has mentioned using v4l2-compliance on the subdevs.
> 
>> Complaining about this really won't help. We know it's a problem and unless
>> someone (me perhaps?) manages to get paid to work on this it's unlikely to
>> change for now.
> 
> Like the above comment, your comment makes no sense.  I'm not complaining,
> I'm trying to find out the details.

Must be me then, it did feel like complaining...

> Yes, MC stuff sucks big time right now, the documentation is poor, there's
> a lack of understanding on all sides of the issues (which can be seen by
> the different opinions that people hold.)  The only way to resolve these
> differences is via discussion, and if you're going to start thinking that
> everyone is complaining, then there's not going to be any forward progress.
> 

Regards,

	Hans

Re: [PATCH v5 00/39] i.MX Media Driver

[Niklas Söderlund]

On 2017-03-20 16:57:54 +0100, Hans Verkuil wrote:
> On 03/20/2017 03:11 PM, Russell King - ARM Linux wrote:
> > On Mon, Mar 20, 2017 at 02:57:03PM +0100, Hans Verkuil wrote:
> >> On 03/20/2017 02:29 PM, Russell King - ARM Linux wrote:
> >>> It's what I have - remember, not everyone is happy to constantly replace
> >>> their distro packages with random new stuff.
> >>
> >> This is a compliance test, which is continuously developed in tandem with
> >> new kernel versions. If you are working with an upstream kernel, then you
> >> should also use the corresponding v4l2-compliance test. What's the point
> >> of using an old one?
> >>
> >> I will not support driver developers that use an old version of the
> >> compliance test, that's a waste of my time.
> > 
> > The reason that people may _not_ wish to constantly update v4l-utils
> > is that it changes the libraries installed on their systems.
> > 
> > So, the solution to that is not to complain about developers not using
> > the latest version, but instead to de-couple it from the rest of the
> > package, and provide it as a separate, stand-alone package that doesn't
> > come with all the extra baggage.
> > 
> > Now, there's two possible answers to that:
> > 
> > 1. it depends on the libv4l2 version.  If that's so, then you are
> >    insisting that people constantly move to the latest libv4l2 because
> >    of API changes, and those API changes may upset applications they're
> >    using.  So this isn't really on.
> > 
> > 2. it doesn't depend on libv4l2 version, in which case there's no reason
> >    for it to be packaged with v4l-utils.
> 
> Run configure with --disable-v4l2-compliance-libv4l.
> 
> This avoids linking with libv4l and allows you to build it stand-alone.
> 
> Perhaps I should invert this option since in most cases you don't want to
> run v4l2-compliance with libv4l (it's off by default unless you pass the
> -w option to v4l2-compliance).
> 
> > 
> > The reality is that v4l2-compliance links with libv4l2, so I'm not sure
> > which it is.  What I am sure of is that I don't want to upgrade libv4l2
> > on an ad-hoc basis, potentially causing issues with applications.
> > 
> >>>> To test actual streaming you need to provide the -s option.
> >>>>
> >>>> Note: v4l2-compliance has been developed for 'regular' video devices,
> >>>> not MC devices. It may or may not work with the -s option.
> >>>
> >>> Right, and it exists to verify that the establised v4l2 API is correctly
> >>> implemented.  If the v4l2 API is being offered to user applications,
> >>> then it must be conformant, otherwise it's not offering the v4l2 API.
> >>> (That's very much a definition statement in itself.)
> >>>
> >>> So, are we really going to say MC devices do not offer the v4l2 API to
> >>> userspace, but something that might work?  We've already seen today
> >>> one user say that they're not going to use mainline because of the
> >>> crud surrounding MC.
> >>>
> >>
> >> Actually, my understanding was that he was stuck on the old kernel code.
> > 
> > Err, sorry, I really don't follow.  Who is "he"?
> 
> "one user say that they're not going to use mainline because of the
> crud surrounding MC."
> 
> > 
> > _I_ was the one who reported the EXPBUF problem.  Your comment makes no
> > sense.
> > 
> >> In the case of v4l2-compliance, I never had the time to make it work with
> >> MC devices. Same for that matter of certain memory to memory devices.
> >>
> >> Just like MC devices these too behave differently. They are partially
> >> supported in v4l2-compliance, but not fully.
> > 
> > It seems you saying that the API provided by /dev/video* for a MC device
> > breaks the v4l2-compliance tests?
> 
> There may be tests in the compliance suite that do not apply for MC devices
> and for which I never check. The compliance suite was never written with MC
> devices in mind, and it certainly hasn't been tested much with such devices.
> 
> It's only very recent that I even got hardware that has MC support...
> 
> From what I can tell from the feedback I got it seems to be OKish, but I
> just can't guarantee that the compliance utility is correct for such devices.
> 
> In particular I doubt the streaming tests (-s, -f, etc.) will work. The -s
> test *might* work if the pipeline is configured correctly before running
> v4l2-compliance. I can't imagine that the -f option would work at all since
> I would expect pipeline validation errors.

I successfully use v4l2-compliance with the -s option to test the 
Renesas R-Car Gen3 driver which uses MC, I first have to setup the 
pipeline using media-ctl. I have had much use of the tool and it have 
helped me catch many errors in the rcar-vin driver both on Gen2 (no MC 
involved) and Gen3. And yes the -f option is only usable on Gen2 where 
MC is not used.

For what it's worth, the first versions of the R-Car Gen3 patches did 
not use MC for anything else then setting up the pipeline, all format 
propagation and communication with subdevice where done using the 
/dev/videoX node and it was rather cumbersome. This was done in part due 
the me not understanding the MC framework. Later versions of the patches 
use MC and depends on the user configuring the pipeline and formats 
before starting the stream and it works better for me.

My ahh moment came when I realised that the pipeline can be different on 
different SoC but still be needed to be handled by the same drivers, I 
for example have two use-cases I look at.

Onboard components on Renesas R-Car Salvator-X. This was the only 
use-case I first considered and the early Gen3 patches handled this 
without MC support.

[ADV7482 (CSI-2 transmitter)] -> [R-Car CSI-2 (CSI-2 receiver)] -> [R-Car VIN (dma engine)]

Later I was presented with a more complex use-case where more devices 
would be involved.

[Sensor (Parallel output)] -> [Parallel to GSML] -> [GSML to CSI-2 (CSI-2 transmitter)] -> [R-Car CSI-2 (CSI-2 receiver)] -> [R-Car VIN (dma engine)]

And I could not see a reasonable way to support both use-cases (or 
others where a different pipeline would be connected to the CSI-2 
receiver present on the SoC itself) without the use of MC. There is no 
good way I can see where I can add the logic to the R-Car VIN driver 
which could cover all the knowledge needed to work with arbitrary 
pipelines. But then again I have lot to still learn about V4L2.

> 
> I've been gently pushing Helen Koike to finish her virtual MC driver
> (https://patchwork.kernel.org/patch/9312783/) since having a virtual driver
> makes writing compliance tests much easier.
> 
> > _No one_ has mentioned using v4l2-compliance on the subdevs.
> > 
> >> Complaining about this really won't help. We know it's a problem and unless
> >> someone (me perhaps?) manages to get paid to work on this it's unlikely to
> >> change for now.
> > 
> > Like the above comment, your comment makes no sense.  I'm not complaining,
> > I'm trying to find out the details.
> 
> Must be me then, it did feel like complaining...
> 
> > Yes, MC stuff sucks big time right now, the documentation is poor, there's
> > a lack of understanding on all sides of the issues (which can be seen by
> > the different opinions that people hold.)  The only way to resolve these
> > differences is via discussion, and if you're going to start thinking that
> > everyone is complaining, then there's not going to be any forward progress.
> > 
> 
> Regards,
> 
> 	Hans

-- 
Regards,
Niklas Söderlund

[PATCH v5 00/39] i.MX Media Driver

[Niklas Söderlund]

On 2017-03-20 16:57:54 +0100, Hans Verkuil wrote:
> On 03/20/2017 03:11 PM, Russell King - ARM Linux wrote:
> > On Mon, Mar 20, 2017 at 02:57:03PM +0100, Hans Verkuil wrote:
> >> On 03/20/2017 02:29 PM, Russell King - ARM Linux wrote:
> >>> It's what I have - remember, not everyone is happy to constantly replace
> >>> their distro packages with random new stuff.
> >>
> >> This is a compliance test, which is continuously developed in tandem with
> >> new kernel versions. If you are working with an upstream kernel, then you
> >> should also use the corresponding v4l2-compliance test. What's the point
> >> of using an old one?
> >>
> >> I will not support driver developers that use an old version of the
> >> compliance test, that's a waste of my time.
> > 
> > The reason that people may _not_ wish to constantly update v4l-utils
> > is that it changes the libraries installed on their systems.
> > 
> > So, the solution to that is not to complain about developers not using
> > the latest version, but instead to de-couple it from the rest of the
> > package, and provide it as a separate, stand-alone package that doesn't
> > come with all the extra baggage.
> > 
> > Now, there's two possible answers to that:
> > 
> > 1. it depends on the libv4l2 version.  If that's so, then you are
> >    insisting that people constantly move to the latest libv4l2 because
> >    of API changes, and those API changes may upset applications they're
> >    using.  So this isn't really on.
> > 
> > 2. it doesn't depend on libv4l2 version, in which case there's no reason
> >    for it to be packaged with v4l-utils.
> 
> Run configure with --disable-v4l2-compliance-libv4l.
> 
> This avoids linking with libv4l and allows you to build it stand-alone.
> 
> Perhaps I should invert this option since in most cases you don't want to
> run v4l2-compliance with libv4l (it's off by default unless you pass the
> -w option to v4l2-compliance).
> 
> > 
> > The reality is that v4l2-compliance links with libv4l2, so I'm not sure
> > which it is.  What I am sure of is that I don't want to upgrade libv4l2
> > on an ad-hoc basis, potentially causing issues with applications.
> > 
> >>>> To test actual streaming you need to provide the -s option.
> >>>>
> >>>> Note: v4l2-compliance has been developed for 'regular' video devices,
> >>>> not MC devices. It may or may not work with the -s option.
> >>>
> >>> Right, and it exists to verify that the establised v4l2 API is correctly
> >>> implemented.  If the v4l2 API is being offered to user applications,
> >>> then it must be conformant, otherwise it's not offering the v4l2 API.
> >>> (That's very much a definition statement in itself.)
> >>>
> >>> So, are we really going to say MC devices do not offer the v4l2 API to
> >>> userspace, but something that might work?  We've already seen today
> >>> one user say that they're not going to use mainline because of the
> >>> crud surrounding MC.
> >>>
> >>
> >> Actually, my understanding was that he was stuck on the old kernel code.
> > 
> > Err, sorry, I really don't follow.  Who is "he"?
> 
> "one user say that they're not going to use mainline because of the
> crud surrounding MC."
> 
> > 
> > _I_ was the one who reported the EXPBUF problem.  Your comment makes no
> > sense.
> > 
> >> In the case of v4l2-compliance, I never had the time to make it work with
> >> MC devices. Same for that matter of certain memory to memory devices.
> >>
> >> Just like MC devices these too behave differently. They are partially
> >> supported in v4l2-compliance, but not fully.
> > 
> > It seems you saying that the API provided by /dev/video* for a MC device
> > breaks the v4l2-compliance tests?
> 
> There may be tests in the compliance suite that do not apply for MC devices
> and for which I never check. The compliance suite was never written with MC
> devices in mind, and it certainly hasn't been tested much with such devices.
> 
> It's only very recent that I even got hardware that has MC support...
> 
> From what I can tell from the feedback I got it seems to be OKish, but I
> just can't guarantee that the compliance utility is correct for such devices.
> 
> In particular I doubt the streaming tests (-s, -f, etc.) will work. The -s
> test *might* work if the pipeline is configured correctly before running
> v4l2-compliance. I can't imagine that the -f option would work at all since
> I would expect pipeline validation errors.

I successfully use v4l2-compliance with the -s option to test the 
Renesas R-Car Gen3 driver which uses MC, I first have to setup the 
pipeline using media-ctl. I have had much use of the tool and it have 
helped me catch many errors in the rcar-vin driver both on Gen2 (no MC 
involved) and Gen3. And yes the -f option is only usable on Gen2 where 
MC is not used.

For what it's worth, the first versions of the R-Car Gen3 patches did 
not use MC for anything else then setting up the pipeline, all format 
propagation and communication with subdevice where done using the 
/dev/videoX node and it was rather cumbersome. This was done in part due 
the me not understanding the MC framework. Later versions of the patches 
use MC and depends on the user configuring the pipeline and formats 
before starting the stream and it works better for me.

My ahh moment came when I realised that the pipeline can be different on 
different SoC but still be needed to be handled by the same drivers, I 
for example have two use-cases I look at.

Onboard components on Renesas R-Car Salvator-X. This was the only 
use-case I first considered and the early Gen3 patches handled this 
without MC support.

[ADV7482 (CSI-2 transmitter)] -> [R-Car CSI-2 (CSI-2 receiver)] -> [R-Car VIN (dma engine)]

Later I was presented with a more complex use-case where more devices 
would be involved.

[Sensor (Parallel output)] -> [Parallel to GSML] -> [GSML to CSI-2 (CSI-2 transmitter)] -> [R-Car CSI-2 (CSI-2 receiver)] -> [R-Car VIN (dma engine)]

And I could not see a reasonable way to support both use-cases (or 
others where a different pipeline would be connected to the CSI-2 
receiver present on the SoC itself) without the use of MC. There is no 
good way I can see where I can add the logic to the R-Car VIN driver 
which could cover all the knowledge needed to work with arbitrary 
pipelines. But then again I have lot to still learn about V4L2.

> 
> I've been gently pushing Helen Koike to finish her virtual MC driver
> (https://patchwork.kernel.org/patch/9312783/) since having a virtual driver
> makes writing compliance tests much easier.
> 
> > _No one_ has mentioned using v4l2-compliance on the subdevs.
> > 
> >> Complaining about this really won't help. We know it's a problem and unless
> >> someone (me perhaps?) manages to get paid to work on this it's unlikely to
> >> change for now.
> > 
> > Like the above comment, your comment makes no sense.  I'm not complaining,
> > I'm trying to find out the details.
> 
> Must be me then, it did feel like complaining...
> 
> > Yes, MC stuff sucks big time right now, the documentation is poor, there's
> > a lack of understanding on all sides of the issues (which can be seen by
> > the different opinions that people hold.)  The only way to resolve these
> > differences is via discussion, and if you're going to start thinking that
> > everyone is complaining, then there's not going to be any forward progress.
> > 
> 
> Regards,
> 
> 	Hans

-- 
Regards,
Niklas S?derlund

Re: [PATCH v5 00/39] i.MX Media Driver

[Niklas Söderlund]

On 2017-03-20 16:57:54 +0100, Hans Verkuil wrote:
> On 03/20/2017 03:11 PM, Russell King - ARM Linux wrote:
> > On Mon, Mar 20, 2017 at 02:57:03PM +0100, Hans Verkuil wrote:
> >> On 03/20/2017 02:29 PM, Russell King - ARM Linux wrote:
> >>> It's what I have - remember, not everyone is happy to constantly replace
> >>> their distro packages with random new stuff.
> >>
> >> This is a compliance test, which is continuously developed in tandem with
> >> new kernel versions. If you are working with an upstream kernel, then you
> >> should also use the corresponding v4l2-compliance test. What's the point
> >> of using an old one?
> >>
> >> I will not support driver developers that use an old version of the
> >> compliance test, that's a waste of my time.
> > 
> > The reason that people may _not_ wish to constantly update v4l-utils
> > is that it changes the libraries installed on their systems.
> > 
> > So, the solution to that is not to complain about developers not using
> > the latest version, but instead to de-couple it from the rest of the
> > package, and provide it as a separate, stand-alone package that doesn't
> > come with all the extra baggage.
> > 
> > Now, there's two possible answers to that:
> > 
> > 1. it depends on the libv4l2 version.  If that's so, then you are
> >    insisting that people constantly move to the latest libv4l2 because
> >    of API changes, and those API changes may upset applications they're
> >    using.  So this isn't really on.
> > 
> > 2. it doesn't depend on libv4l2 version, in which case there's no reason
> >    for it to be packaged with v4l-utils.
> 
> Run configure with --disable-v4l2-compliance-libv4l.
> 
> This avoids linking with libv4l and allows you to build it stand-alone.
> 
> Perhaps I should invert this option since in most cases you don't want to
> run v4l2-compliance with libv4l (it's off by default unless you pass the
> -w option to v4l2-compliance).
> 
> > 
> > The reality is that v4l2-compliance links with libv4l2, so I'm not sure
> > which it is.  What I am sure of is that I don't want to upgrade libv4l2
> > on an ad-hoc basis, potentially causing issues with applications.
> > 
> >>>> To test actual streaming you need to provide the -s option.
> >>>>
> >>>> Note: v4l2-compliance has been developed for 'regular' video devices,
> >>>> not MC devices. It may or may not work with the -s option.
> >>>
> >>> Right, and it exists to verify that the establised v4l2 API is correctly
> >>> implemented.  If the v4l2 API is being offered to user applications,
> >>> then it must be conformant, otherwise it's not offering the v4l2 API.
> >>> (That's very much a definition statement in itself.)
> >>>
> >>> So, are we really going to say MC devices do not offer the v4l2 API to
> >>> userspace, but something that might work?  We've already seen today
> >>> one user say that they're not going to use mainline because of the
> >>> crud surrounding MC.
> >>>
> >>
> >> Actually, my understanding was that he was stuck on the old kernel code.
> > 
> > Err, sorry, I really don't follow.  Who is "he"?
> 
> "one user say that they're not going to use mainline because of the
> crud surrounding MC."
> 
> > 
> > _I_ was the one who reported the EXPBUF problem.  Your comment makes no
> > sense.
> > 
> >> In the case of v4l2-compliance, I never had the time to make it work with
> >> MC devices. Same for that matter of certain memory to memory devices.
> >>
> >> Just like MC devices these too behave differently. They are partially
> >> supported in v4l2-compliance, but not fully.
> > 
> > It seems you saying that the API provided by /dev/video* for a MC device
> > breaks the v4l2-compliance tests?
> 
> There may be tests in the compliance suite that do not apply for MC devices
> and for which I never check. The compliance suite was never written with MC
> devices in mind, and it certainly hasn't been tested much with such devices.
> 
> It's only very recent that I even got hardware that has MC support...
> 
> From what I can tell from the feedback I got it seems to be OKish, but I
> just can't guarantee that the compliance utility is correct for such devices.
> 
> In particular I doubt the streaming tests (-s, -f, etc.) will work. The -s
> test *might* work if the pipeline is configured correctly before running
> v4l2-compliance. I can't imagine that the -f option would work at all since
> I would expect pipeline validation errors.

I successfully use v4l2-compliance with the -s option to test the 
Renesas R-Car Gen3 driver which uses MC, I first have to setup the 
pipeline using media-ctl. I have had much use of the tool and it have 
helped me catch many errors in the rcar-vin driver both on Gen2 (no MC 
involved) and Gen3. And yes the -f option is only usable on Gen2 where 
MC is not used.

For what it's worth, the first versions of the R-Car Gen3 patches did 
not use MC for anything else then setting up the pipeline, all format 
propagation and communication with subdevice where done using the 
/dev/videoX node and it was rather cumbersome. This was done in part due 
the me not understanding the MC framework. Later versions of the patches 
use MC and depends on the user configuring the pipeline and formats 
before starting the stream and it works better for me.

My ahh moment came when I realised that the pipeline can be different on 
different SoC but still be needed to be handled by the same drivers, I 
for example have two use-cases I look at.

Onboard components on Renesas R-Car Salvator-X. This was the only 
use-case I first considered and the early Gen3 patches handled this 
without MC support.

[ADV7482 (CSI-2 transmitter)] -> [R-Car CSI-2 (CSI-2 receiver)] -> [R-Car VIN (dma engine)]

Later I was presented with a more complex use-case where more devices 
would be involved.

[Sensor (Parallel output)] -> [Parallel to GSML] -> [GSML to CSI-2 (CSI-2 transmitter)] -> [R-Car CSI-2 (CSI-2 receiver)] -> [R-Car VIN (dma engine)]

And I could not see a reasonable way to support both use-cases (or 
others where a different pipeline would be connected to the CSI-2 
receiver present on the SoC itself) without the use of MC. There is no 
good way I can see where I can add the logic to the R-Car VIN driver 
which could cover all the knowledge needed to work with arbitrary 
pipelines. But then again I have lot to still learn about V4L2.

> 
> I've been gently pushing Helen Koike to finish her virtual MC driver
> (https://patchwork.kernel.org/patch/9312783/) since having a virtual driver
> makes writing compliance tests much easier.
> 
> > _No one_ has mentioned using v4l2-compliance on the subdevs.
> > 
> >> Complaining about this really won't help. We know it's a problem and unless
> >> someone (me perhaps?) manages to get paid to work on this it's unlikely to
> >> change for now.
> > 
> > Like the above comment, your comment makes no sense.  I'm not complaining,
> > I'm trying to find out the details.
> 
> Must be me then, it did feel like complaining...
> 
> > Yes, MC stuff sucks big time right now, the documentation is poor, there's
> > a lack of understanding on all sides of the issues (which can be seen by
> > the different opinions that people hold.)  The only way to resolve these
> > differences is via discussion, and if you're going to start thinking that
> > everyone is complaining, then there's not going to be any forward progress.
> > 
> 
> Regards,
> 
> 	Hans

-- 
Regards,
Niklas Söderlund
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 00/39] i.MX Media Driver

[Hans Verkuil]

On 03/21/17 11:42, Niklas Söderlund wrote:
> On 2017-03-20 16:57:54 +0100, Hans Verkuil wrote:
>> On 03/20/2017 03:11 PM, Russell King - ARM Linux wrote:
>>> On Mon, Mar 20, 2017 at 02:57:03PM +0100, Hans Verkuil wrote:
>>>> On 03/20/2017 02:29 PM, Russell King - ARM Linux wrote:
>>>>> It's what I have - remember, not everyone is happy to constantly replace
>>>>> their distro packages with random new stuff.
>>>>
>>>> This is a compliance test, which is continuously developed in tandem with
>>>> new kernel versions. If you are working with an upstream kernel, then you
>>>> should also use the corresponding v4l2-compliance test. What's the point
>>>> of using an old one?
>>>>
>>>> I will not support driver developers that use an old version of the
>>>> compliance test, that's a waste of my time.
>>>
>>> The reason that people may _not_ wish to constantly update v4l-utils
>>> is that it changes the libraries installed on their systems.
>>>
>>> So, the solution to that is not to complain about developers not using
>>> the latest version, but instead to de-couple it from the rest of the
>>> package, and provide it as a separate, stand-alone package that doesn't
>>> come with all the extra baggage.
>>>
>>> Now, there's two possible answers to that:
>>>
>>> 1. it depends on the libv4l2 version.  If that's so, then you are
>>>    insisting that people constantly move to the latest libv4l2 because
>>>    of API changes, and those API changes may upset applications they're
>>>    using.  So this isn't really on.
>>>
>>> 2. it doesn't depend on libv4l2 version, in which case there's no reason
>>>    for it to be packaged with v4l-utils.
>>
>> Run configure with --disable-v4l2-compliance-libv4l.
>>
>> This avoids linking with libv4l and allows you to build it stand-alone.
>>
>> Perhaps I should invert this option since in most cases you don't want to
>> run v4l2-compliance with libv4l (it's off by default unless you pass the
>> -w option to v4l2-compliance).
>>
>>>
>>> The reality is that v4l2-compliance links with libv4l2, so I'm not sure
>>> which it is.  What I am sure of is that I don't want to upgrade libv4l2
>>> on an ad-hoc basis, potentially causing issues with applications.
>>>
>>>>>> To test actual streaming you need to provide the -s option.
>>>>>>
>>>>>> Note: v4l2-compliance has been developed for 'regular' video devices,
>>>>>> not MC devices. It may or may not work with the -s option.
>>>>>
>>>>> Right, and it exists to verify that the establised v4l2 API is correctly
>>>>> implemented.  If the v4l2 API is being offered to user applications,
>>>>> then it must be conformant, otherwise it's not offering the v4l2 API.
>>>>> (That's very much a definition statement in itself.)
>>>>>
>>>>> So, are we really going to say MC devices do not offer the v4l2 API to
>>>>> userspace, but something that might work?  We've already seen today
>>>>> one user say that they're not going to use mainline because of the
>>>>> crud surrounding MC.
>>>>>
>>>>
>>>> Actually, my understanding was that he was stuck on the old kernel code.
>>>
>>> Err, sorry, I really don't follow.  Who is "he"?
>>
>> "one user say that they're not going to use mainline because of the
>> crud surrounding MC."
>>
>>>
>>> _I_ was the one who reported the EXPBUF problem.  Your comment makes no
>>> sense.
>>>
>>>> In the case of v4l2-compliance, I never had the time to make it work with
>>>> MC devices. Same for that matter of certain memory to memory devices.
>>>>
>>>> Just like MC devices these too behave differently. They are partially
>>>> supported in v4l2-compliance, but not fully.
>>>
>>> It seems you saying that the API provided by /dev/video* for a MC device
>>> breaks the v4l2-compliance tests?
>>
>> There may be tests in the compliance suite that do not apply for MC devices
>> and for which I never check. The compliance suite was never written with MC
>> devices in mind, and it certainly hasn't been tested much with such devices.
>>
>> It's only very recent that I even got hardware that has MC support...
>>
>> From what I can tell from the feedback I got it seems to be OKish, but I
>> just can't guarantee that the compliance utility is correct for such devices.
>>
>> In particular I doubt the streaming tests (-s, -f, etc.) will work. The -s
>> test *might* work if the pipeline is configured correctly before running
>> v4l2-compliance. I can't imagine that the -f option would work at all since
>> I would expect pipeline validation errors.
> 
> I successfully use v4l2-compliance with the -s option to test the 
> Renesas R-Car Gen3 driver which uses MC, I first have to setup the 
> pipeline using media-ctl. I have had much use of the tool and it have 
> helped me catch many errors in the rcar-vin driver both on Gen2 (no MC 
> involved) and Gen3. And yes the -f option is only usable on Gen2 where 
> MC is not used.

Ah, good to hear that -s works with MC. I was not sure about that.
Thanks for the feedback!

Regards,

	Hans

[PATCH v5 00/39] i.MX Media Driver

[Hans Verkuil]

On 03/21/17 11:42, Niklas S?derlund wrote:
> On 2017-03-20 16:57:54 +0100, Hans Verkuil wrote:
>> On 03/20/2017 03:11 PM, Russell King - ARM Linux wrote:
>>> On Mon, Mar 20, 2017 at 02:57:03PM +0100, Hans Verkuil wrote:
>>>> On 03/20/2017 02:29 PM, Russell King - ARM Linux wrote:
>>>>> It's what I have - remember, not everyone is happy to constantly replace
>>>>> their distro packages with random new stuff.
>>>>
>>>> This is a compliance test, which is continuously developed in tandem with
>>>> new kernel versions. If you are working with an upstream kernel, then you
>>>> should also use the corresponding v4l2-compliance test. What's the point
>>>> of using an old one?
>>>>
>>>> I will not support driver developers that use an old version of the
>>>> compliance test, that's a waste of my time.
>>>
>>> The reason that people may _not_ wish to constantly update v4l-utils
>>> is that it changes the libraries installed on their systems.
>>>
>>> So, the solution to that is not to complain about developers not using
>>> the latest version, but instead to de-couple it from the rest of the
>>> package, and provide it as a separate, stand-alone package that doesn't
>>> come with all the extra baggage.
>>>
>>> Now, there's two possible answers to that:
>>>
>>> 1. it depends on the libv4l2 version.  If that's so, then you are
>>>    insisting that people constantly move to the latest libv4l2 because
>>>    of API changes, and those API changes may upset applications they're
>>>    using.  So this isn't really on.
>>>
>>> 2. it doesn't depend on libv4l2 version, in which case there's no reason
>>>    for it to be packaged with v4l-utils.
>>
>> Run configure with --disable-v4l2-compliance-libv4l.
>>
>> This avoids linking with libv4l and allows you to build it stand-alone.
>>
>> Perhaps I should invert this option since in most cases you don't want to
>> run v4l2-compliance with libv4l (it's off by default unless you pass the
>> -w option to v4l2-compliance).
>>
>>>
>>> The reality is that v4l2-compliance links with libv4l2, so I'm not sure
>>> which it is.  What I am sure of is that I don't want to upgrade libv4l2
>>> on an ad-hoc basis, potentially causing issues with applications.
>>>
>>>>>> To test actual streaming you need to provide the -s option.
>>>>>>
>>>>>> Note: v4l2-compliance has been developed for 'regular' video devices,
>>>>>> not MC devices. It may or may not work with the -s option.
>>>>>
>>>>> Right, and it exists to verify that the establised v4l2 API is correctly
>>>>> implemented.  If the v4l2 API is being offered to user applications,
>>>>> then it must be conformant, otherwise it's not offering the v4l2 API.
>>>>> (That's very much a definition statement in itself.)
>>>>>
>>>>> So, are we really going to say MC devices do not offer the v4l2 API to
>>>>> userspace, but something that might work?  We've already seen today
>>>>> one user say that they're not going to use mainline because of the
>>>>> crud surrounding MC.
>>>>>
>>>>
>>>> Actually, my understanding was that he was stuck on the old kernel code.
>>>
>>> Err, sorry, I really don't follow.  Who is "he"?
>>
>> "one user say that they're not going to use mainline because of the
>> crud surrounding MC."
>>
>>>
>>> _I_ was the one who reported the EXPBUF problem.  Your comment makes no
>>> sense.
>>>
>>>> In the case of v4l2-compliance, I never had the time to make it work with
>>>> MC devices. Same for that matter of certain memory to memory devices.
>>>>
>>>> Just like MC devices these too behave differently. They are partially
>>>> supported in v4l2-compliance, but not fully.
>>>
>>> It seems you saying that the API provided by /dev/video* for a MC device
>>> breaks the v4l2-compliance tests?
>>
>> There may be tests in the compliance suite that do not apply for MC devices
>> and for which I never check. The compliance suite was never written with MC
>> devices in mind, and it certainly hasn't been tested much with such devices.
>>
>> It's only very recent that I even got hardware that has MC support...
>>
>> From what I can tell from the feedback I got it seems to be OKish, but I
>> just can't guarantee that the compliance utility is correct for such devices.
>>
>> In particular I doubt the streaming tests (-s, -f, etc.) will work. The -s
>> test *might* work if the pipeline is configured correctly before running
>> v4l2-compliance. I can't imagine that the -f option would work at all since
>> I would expect pipeline validation errors.
> 
> I successfully use v4l2-compliance with the -s option to test the 
> Renesas R-Car Gen3 driver which uses MC, I first have to setup the 
> pipeline using media-ctl. I have had much use of the tool and it have 
> helped me catch many errors in the rcar-vin driver both on Gen2 (no MC 
> involved) and Gen3. And yes the -f option is only usable on Gen2 where 
> MC is not used.

Ah, good to hear that -s works with MC. I was not sure about that.
Thanks for the feedback!

Regards,

	Hans

Re: [PATCH v5 00/39] i.MX Media Driver

[Hans Verkuil]

On 03/21/17 11:42, Niklas Söderlund wrote:
> On 2017-03-20 16:57:54 +0100, Hans Verkuil wrote:
>> On 03/20/2017 03:11 PM, Russell King - ARM Linux wrote:
>>> On Mon, Mar 20, 2017 at 02:57:03PM +0100, Hans Verkuil wrote:
>>>> On 03/20/2017 02:29 PM, Russell King - ARM Linux wrote:
>>>>> It's what I have - remember, not everyone is happy to constantly replace
>>>>> their distro packages with random new stuff.
>>>>
>>>> This is a compliance test, which is continuously developed in tandem with
>>>> new kernel versions. If you are working with an upstream kernel, then you
>>>> should also use the corresponding v4l2-compliance test. What's the point
>>>> of using an old one?
>>>>
>>>> I will not support driver developers that use an old version of the
>>>> compliance test, that's a waste of my time.
>>>
>>> The reason that people may _not_ wish to constantly update v4l-utils
>>> is that it changes the libraries installed on their systems.
>>>
>>> So, the solution to that is not to complain about developers not using
>>> the latest version, but instead to de-couple it from the rest of the
>>> package, and provide it as a separate, stand-alone package that doesn't
>>> come with all the extra baggage.
>>>
>>> Now, there's two possible answers to that:
>>>
>>> 1. it depends on the libv4l2 version.  If that's so, then you are
>>>    insisting that people constantly move to the latest libv4l2 because
>>>    of API changes, and those API changes may upset applications they're
>>>    using.  So this isn't really on.
>>>
>>> 2. it doesn't depend on libv4l2 version, in which case there's no reason
>>>    for it to be packaged with v4l-utils.
>>
>> Run configure with --disable-v4l2-compliance-libv4l.
>>
>> This avoids linking with libv4l and allows you to build it stand-alone.
>>
>> Perhaps I should invert this option since in most cases you don't want to
>> run v4l2-compliance with libv4l (it's off by default unless you pass the
>> -w option to v4l2-compliance).
>>
>>>
>>> The reality is that v4l2-compliance links with libv4l2, so I'm not sure
>>> which it is.  What I am sure of is that I don't want to upgrade libv4l2
>>> on an ad-hoc basis, potentially causing issues with applications.
>>>
>>>>>> To test actual streaming you need to provide the -s option.
>>>>>>
>>>>>> Note: v4l2-compliance has been developed for 'regular' video devices,
>>>>>> not MC devices. It may or may not work with the -s option.
>>>>>
>>>>> Right, and it exists to verify that the establised v4l2 API is correctly
>>>>> implemented.  If the v4l2 API is being offered to user applications,
>>>>> then it must be conformant, otherwise it's not offering the v4l2 API.
>>>>> (That's very much a definition statement in itself.)
>>>>>
>>>>> So, are we really going to say MC devices do not offer the v4l2 API to
>>>>> userspace, but something that might work?  We've already seen today
>>>>> one user say that they're not going to use mainline because of the
>>>>> crud surrounding MC.
>>>>>
>>>>
>>>> Actually, my understanding was that he was stuck on the old kernel code.
>>>
>>> Err, sorry, I really don't follow.  Who is "he"?
>>
>> "one user say that they're not going to use mainline because of the
>> crud surrounding MC."
>>
>>>
>>> _I_ was the one who reported the EXPBUF problem.  Your comment makes no
>>> sense.
>>>
>>>> In the case of v4l2-compliance, I never had the time to make it work with
>>>> MC devices. Same for that matter of certain memory to memory devices.
>>>>
>>>> Just like MC devices these too behave differently. They are partially
>>>> supported in v4l2-compliance, but not fully.
>>>
>>> It seems you saying that the API provided by /dev/video* for a MC device
>>> breaks the v4l2-compliance tests?
>>
>> There may be tests in the compliance suite that do not apply for MC devices
>> and for which I never check. The compliance suite was never written with MC
>> devices in mind, and it certainly hasn't been tested much with such devices.
>>
>> It's only very recent that I even got hardware that has MC support...
>>
>> From what I can tell from the feedback I got it seems to be OKish, but I
>> just can't guarantee that the compliance utility is correct for such devices.
>>
>> In particular I doubt the streaming tests (-s, -f, etc.) will work. The -s
>> test *might* work if the pipeline is configured correctly before running
>> v4l2-compliance. I can't imagine that the -f option would work at all since
>> I would expect pipeline validation errors.
> 
> I successfully use v4l2-compliance with the -s option to test the 
> Renesas R-Car Gen3 driver which uses MC, I first have to setup the 
> pipeline using media-ctl. I have had much use of the tool and it have 
> helped me catch many errors in the rcar-vin driver both on Gen2 (no MC 
> involved) and Gen3. And yes the -f option is only usable on Gen2 where 
> MC is not used.

Ah, good to hear that -s works with MC. I was not sure about that.
Thanks for the feedback!

Regards,

	Hans

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Tue, Mar 21, 2017 at 11:59:02AM +0100, Hans Verkuil wrote:
> Ah, good to hear that -s works with MC. I was not sure about that.
> Thanks for the feedback!

Not soo good on iMX6:

$ v4l2-compliance -d /dev/video10 -s --expbuf-device=/dev/video0
...
Input ioctls:
        test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported)
        test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
        test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported)
        test VIDIOC_ENUMAUDIO: OK (Not Supported)
                fail: v4l2-test-input-output.cpp(420): G_INPUT not supported for a capture device
        test VIDIOC_G/S/ENUMINPUT: FAIL
        test VIDIOC_G/S_AUDIO: OK (Not Supported)
        Inputs: 0 Audio Inputs: 0 Tuners: 0
...
        Control ioctls:
                test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK
                test VIDIOC_QUERYCTRL: OK
                test VIDIOC_G/S_CTRL: OK
                test VIDIOC_G/S/TRY_EXT_CTRLS: OK
                fail: v4l2-test-controls.cpp(782): subscribe event for control 'User Controls' failed
                test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL
...
Streaming ioctls:
        test read/write: OK (Not Supported)
                fail: v4l2-test-buffers.cpp(297): g_field() == V4L2_FIELD_ANY
                fail: v4l2-test-buffers.cpp(703): buf.check(q, last_seq)
                fail: v4l2-test-buffers.cpp(973): captureBufs(node, q, m2m_q, frame_count, false)
        test MMAP: FAIL
        test USERPTR: OK (Not Supported)
                fail: v4l2-test-buffers.cpp(1188): can_stream && ret != EINVAL
        test DMABUF: FAIL

(/dev/video0 being CODA).  CODA itself seems to have failures:

        Format ioctls:
                test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
                warn: v4l2-test-formats.cpp(1187): S_PARM is supported for buftype 2, but not ENUM_FRAMEINTERVALS
                warn: v4l2-test-formats.cpp(1194): S_PARM is supported but doesn't report V4L2_CAP_TIMEPERFRAME
                test VIDIOC_G/S_PARM: OK
                test VIDIOC_G_FBUF: OK (Not Supported)
                test VIDIOC_G_FMT: OK
                test VIDIOC_TRY_FMT: OK
                fail: v4l2-test-formats.cpp(774): fmt_out.g_colorspace() != col
...
Streaming ioctls:
        test read/write: OK (Not Supported)
                fail: v4l2-test-buffers.cpp(956): q.create_bufs(node, 1, &fmt) != EINVAL
        test MMAP: FAIL
        test USERPTR: OK (Not Supported)
        test DMABUF: Cannot test, specify --expbuf-device

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Tue, Mar 21, 2017 at 11:59:02AM +0100, Hans Verkuil wrote:
> Ah, good to hear that -s works with MC. I was not sure about that.
> Thanks for the feedback!

Not soo good on iMX6:

$ v4l2-compliance -d /dev/video10 -s --expbuf-device=/dev/video0
...
Input ioctls:
        test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported)
        test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
        test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported)
        test VIDIOC_ENUMAUDIO: OK (Not Supported)
                fail: v4l2-test-input-output.cpp(420): G_INPUT not supported for a capture device
        test VIDIOC_G/S/ENUMINPUT: FAIL
        test VIDIOC_G/S_AUDIO: OK (Not Supported)
        Inputs: 0 Audio Inputs: 0 Tuners: 0
...
        Control ioctls:
                test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK
                test VIDIOC_QUERYCTRL: OK
                test VIDIOC_G/S_CTRL: OK
                test VIDIOC_G/S/TRY_EXT_CTRLS: OK
                fail: v4l2-test-controls.cpp(782): subscribe event for control 'User Controls' failed
                test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL
...
Streaming ioctls:
        test read/write: OK (Not Supported)
                fail: v4l2-test-buffers.cpp(297): g_field() == V4L2_FIELD_ANY
                fail: v4l2-test-buffers.cpp(703): buf.check(q, last_seq)
                fail: v4l2-test-buffers.cpp(973): captureBufs(node, q, m2m_q, frame_count, false)
        test MMAP: FAIL
        test USERPTR: OK (Not Supported)
                fail: v4l2-test-buffers.cpp(1188): can_stream && ret != EINVAL
        test DMABUF: FAIL

(/dev/video0 being CODA).  CODA itself seems to have failures:

        Format ioctls:
                test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
                warn: v4l2-test-formats.cpp(1187): S_PARM is supported for buftype 2, but not ENUM_FRAMEINTERVALS
                warn: v4l2-test-formats.cpp(1194): S_PARM is supported but doesn't report V4L2_CAP_TIMEPERFRAME
                test VIDIOC_G/S_PARM: OK
                test VIDIOC_G_FBUF: OK (Not Supported)
                test VIDIOC_G_FMT: OK
                test VIDIOC_TRY_FMT: OK
                fail: v4l2-test-formats.cpp(774): fmt_out.g_colorspace() != col
...
Streaming ioctls:
        test read/write: OK (Not Supported)
                fail: v4l2-test-buffers.cpp(956): q.create_bufs(node, 1, &fmt) != EINVAL
        test MMAP: FAIL
        test USERPTR: OK (Not Supported)
        test DMABUF: Cannot test, specify --expbuf-device

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Tue, Mar 21, 2017 at 11:59:02AM +0100, Hans Verkuil wrote:
> Ah, good to hear that -s works with MC. I was not sure about that.
> Thanks for the feedback!

Not soo good on iMX6:

$ v4l2-compliance -d /dev/video10 -s --expbuf-device=/dev/video0
...
Input ioctls:
        test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported)
        test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
        test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported)
        test VIDIOC_ENUMAUDIO: OK (Not Supported)
                fail: v4l2-test-input-output.cpp(420): G_INPUT not supported for a capture device
        test VIDIOC_G/S/ENUMINPUT: FAIL
        test VIDIOC_G/S_AUDIO: OK (Not Supported)
        Inputs: 0 Audio Inputs: 0 Tuners: 0
...
        Control ioctls:
                test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK
                test VIDIOC_QUERYCTRL: OK
                test VIDIOC_G/S_CTRL: OK
                test VIDIOC_G/S/TRY_EXT_CTRLS: OK
                fail: v4l2-test-controls.cpp(782): subscribe event for control 'User Controls' failed
                test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL
...
Streaming ioctls:
        test read/write: OK (Not Supported)
                fail: v4l2-test-buffers.cpp(297): g_field() == V4L2_FIELD_ANY
                fail: v4l2-test-buffers.cpp(703): buf.check(q, last_seq)
                fail: v4l2-test-buffers.cpp(973): captureBufs(node, q, m2m_q, frame_count, false)
        test MMAP: FAIL
        test USERPTR: OK (Not Supported)
                fail: v4l2-test-buffers.cpp(1188): can_stream && ret != EINVAL
        test DMABUF: FAIL

(/dev/video0 being CODA).  CODA itself seems to have failures:

        Format ioctls:
                test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
                warn: v4l2-test-formats.cpp(1187): S_PARM is supported for buftype 2, but not ENUM_FRAMEINTERVALS
                warn: v4l2-test-formats.cpp(1194): S_PARM is supported but doesn't report V4L2_CAP_TIMEPERFRAME
                test VIDIOC_G/S_PARM: OK
                test VIDIOC_G_FBUF: OK (Not Supported)
                test VIDIOC_G_FMT: OK
                test VIDIOC_TRY_FMT: OK
                fail: v4l2-test-formats.cpp(774): fmt_out.g_colorspace() != col
...
Streaming ioctls:
        test read/write: OK (Not Supported)
                fail: v4l2-test-buffers.cpp(956): q.create_bufs(node, 1, &fmt) != EINVAL
        test MMAP: FAIL
        test USERPTR: OK (Not Supported)
        test DMABUF: Cannot test, specify --expbuf-device

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Nicolas Dufresne]

[-- Attachment #1: Type: text/plain, Size: 603 bytes --]

Le mardi 21 mars 2017 à 11:36 +0000, Russell King - ARM Linux a écrit :
>                 warn: v4l2-test-formats.cpp(1187): S_PARM is
> supported for buftype 2, but not ENUM_FRAMEINTERVALS
>                 warn: v4l2-test-formats.cpp(1194): S_PARM is
> supported but doesn't report V4L2_CAP_TIMEPERFRAME

For encoders, the framerate value is used as numerical value to
implement bitrate control. So in most cases any interval is accepted.
Though, it would be cleaner to just implement the enumeration. It's
quite simple when you support everything.

Nicolas

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

[PATCH v5 00/39] i.MX Media Driver

[Nicolas Dufresne]

Le mardi 21 mars 2017 ? 11:36 +0000, Russell King - ARM Linux a ?crit?:
> ??????????????? warn: v4l2-test-formats.cpp(1187): S_PARM is
> supported for buftype 2, but not ENUM_FRAMEINTERVALS
> ??????????????? warn: v4l2-test-formats.cpp(1194): S_PARM is
> supported but doesn't report V4L2_CAP_TIMEPERFRAME

For encoders, the framerate value is used as numerical value to
implement bitrate control. So in most cases any interval is accepted.
Though, it would be cleaner to just implement the enumeration. It's
quite simple when you support everything.

Nicolas
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 181 bytes
Desc: This is a digitally signed message part
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170322/fad1c83e/attachment.sig>

Re: [PATCH v5 00/39] i.MX Media Driver

[Nicolas Dufresne]

[-- Attachment #1: Type: text/plain, Size: 603 bytes --]

Le mardi 21 mars 2017 à 11:36 +0000, Russell King - ARM Linux a écrit :
>                 warn: v4l2-test-formats.cpp(1187): S_PARM is
> supported for buftype 2, but not ENUM_FRAMEINTERVALS
>                 warn: v4l2-test-formats.cpp(1194): S_PARM is
> supported but doesn't report V4L2_CAP_TIMEPERFRAME

For encoders, the framerate value is used as numerical value to
implement bitrate control. So in most cases any interval is accepted.
Though, it would be cleaner to just implement the enumeration. It's
quite simple when you support everything.

Nicolas

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> On 03/18/2017 12:22 PM, Russell King - ARM Linux wrote:
> >0:00:01.955927879 20954  0x15ffe90 INFO                    v4l2 gstv4l2object.c:3811:gst_v4l2_object_get_caps:<v4l2src0> probed caps: video/x-bayer, format=(string)rggb, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)I420, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)YV12, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)BGR, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)RGB, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1
> >
> >    despite the media pipeline actually being configured for 60fps.
> >
> >    Forcing it by adjusting the pipeline only results in gstreamer
> >    failing, because it believes that v4l2 is unable to operate at
> >    60fps.
> >
> >    Also note the complaints from v4l2src about the non-compliance...
> 
> Thanks, I've fixed most of v4l2-compliance issues, but this is not
> done yet. Is that something you can help with?

I've looked at this, and IMHO it's yet another media control API mess.

- media-ctl itself allows setting the format on subdev pads via
  struct v4l2_subdev_format.

- struct v4l2_subdev_format contains a struct v4l2_mbus_framefmt.

- struct v4l2_mbus_framefmt contains:
  * @width:      frame width
  * @height:     frame height
  * @code:       data format code (from enum v4l2_mbus_pixelcode)
  * @field:      used interlacing type (from enum v4l2_field)
  * @colorspace: colorspace of the data (from enum v4l2_colorspace)
  * @ycbcr_enc:  YCbCr encoding of the data (from enum v4l2_ycbcr_encoding)
  * @quantization: quantization of the data (from enum v4l2_quantization)
  * @xfer_func:  transfer function of the data (from enum v4l2_xfer_func)

- media-ctl sets width, height, code and field, but nothing else.

We're already agreed that the fields that media-ctl are part of the
format negotiation between the ultimate source, flowing down to the
capture device.  However, there's no support in media-ctl to deal
with these other fields - so media-ctl in itself is only half-
implemented.

>From what I can tell, _we_ are doing the right thing in imx-media-capture.

However, I think part of the problem is the set_fmt implementation.
When a source pad is configured via set_fmt(), any fields that can
not be altered (eg, because the subdev doesn't support colorspace
conversion) need to be preserved from the subdev's sink pad.

Right now, CSI doesn't do that - it only looks at the width, height,
code, and field.

I think we've got other bugs though that haven't been picked up by any
review - csi_try_fmt() adjusts the format using the _current_
configuration of the sink pad, even when using V4L2_SUBDEV_FORMAT_TRY.
This seems wrong according to the docs: the purpose of the try
mechanism is to be able to setup the _entire_ pipeline using the TRY
mechanism to work out whether the configuration works, before then
setting for real.  If we're validating the TRY formats against the
live configuration, then we're not doing that.

There's calls for:

v4l2_subdev_get_try_format
v4l2_subdev_get_try_crop
v4l2_subdev_get_try_compose

to get the try configuration - we hardly make use of all of these.  I
would suggest that we change the approach to implementing the various
subdevs such that:

1) like __csi_get_fmt(), we have accessors that gets a pointer to the
   correct state for the TRY/live settings.

2) everywhere we're asked to get or set parameters that can be TRY/live,
   we use these accessors to retrieve a pointer to the correct state to
   not only read, but also modify.

3) when we're evaluating parameters against another pad, we use these
   accessors to obtain the other pad's configuration, rather than poking
   about in the state saved in the subdev's priv-> (which is irrelevant
   for the TRY variant.)

4) ensure that all parameters which the subdev itself does not support
   modification of are correctly propagated from the sink pad to all
   source pads, and are unable to be modified via the source pad.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> On 03/18/2017 12:22 PM, Russell King - ARM Linux wrote:
> >0:00:01.955927879 20954  0x15ffe90 INFO                    v4l2 gstv4l2object.c:3811:gst_v4l2_object_get_caps:<v4l2src0> probed caps: video/x-bayer, format=(string)rggb, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)I420, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)YV12, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)BGR, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)RGB, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1
> >
> >    despite the media pipeline actually being configured for 60fps.
> >
> >    Forcing it by adjusting the pipeline only results in gstreamer
> >    failing, because it believes that v4l2 is unable to operate at
> >    60fps.
> >
> >    Also note the complaints from v4l2src about the non-compliance...
> 
> Thanks, I've fixed most of v4l2-compliance issues, but this is not
> done yet. Is that something you can help with?

I've looked at this, and IMHO it's yet another media control API mess.

- media-ctl itself allows setting the format on subdev pads via
  struct v4l2_subdev_format.

- struct v4l2_subdev_format contains a struct v4l2_mbus_framefmt.

- struct v4l2_mbus_framefmt contains:
  * @width:      frame width
  * @height:     frame height
  * @code:       data format code (from enum v4l2_mbus_pixelcode)
  * @field:      used interlacing type (from enum v4l2_field)
  * @colorspace: colorspace of the data (from enum v4l2_colorspace)
  * @ycbcr_enc:  YCbCr encoding of the data (from enum v4l2_ycbcr_encoding)
  * @quantization: quantization of the data (from enum v4l2_quantization)
  * @xfer_func:  transfer function of the data (from enum v4l2_xfer_func)

- media-ctl sets width, height, code and field, but nothing else.

We're already agreed that the fields that media-ctl are part of the
format negotiation between the ultimate source, flowing down to the
capture device.  However, there's no support in media-ctl to deal
with these other fields - so media-ctl in itself is only half-
implemented.

>From what I can tell, _we_ are doing the right thing in imx-media-capture.

However, I think part of the problem is the set_fmt implementation.
When a source pad is configured via set_fmt(), any fields that can
not be altered (eg, because the subdev doesn't support colorspace
conversion) need to be preserved from the subdev's sink pad.

Right now, CSI doesn't do that - it only looks at the width, height,
code, and field.

I think we've got other bugs though that haven't been picked up by any
review - csi_try_fmt() adjusts the format using the _current_
configuration of the sink pad, even when using V4L2_SUBDEV_FORMAT_TRY.
This seems wrong according to the docs: the purpose of the try
mechanism is to be able to setup the _entire_ pipeline using the TRY
mechanism to work out whether the configuration works, before then
setting for real.  If we're validating the TRY formats against the
live configuration, then we're not doing that.

There's calls for:

v4l2_subdev_get_try_format
v4l2_subdev_get_try_crop
v4l2_subdev_get_try_compose

to get the try configuration - we hardly make use of all of these.  I
would suggest that we change the approach to implementing the various
subdevs such that:

1) like __csi_get_fmt(), we have accessors that gets a pointer to the
   correct state for the TRY/live settings.

2) everywhere we're asked to get or set parameters that can be TRY/live,
   we use these accessors to retrieve a pointer to the correct state to
   not only read, but also modify.

3) when we're evaluating parameters against another pad, we use these
   accessors to obtain the other pad's configuration, rather than poking
   about in the state saved in the subdev's priv-> (which is irrelevant
   for the TRY variant.)

4) ensure that all parameters which the subdev itself does not support
   modification of are correctly propagated from the sink pad to all
   source pads, and are unable to be modified via the source pad.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> On 03/18/2017 12:22 PM, Russell King - ARM Linux wrote:
> >0:00:01.955927879 20954  0x15ffe90 INFO                    v4l2 gstv4l2object.c:3811:gst_v4l2_object_get_caps:<v4l2src0> probed caps: video/x-bayer, format=(string)rggb, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)I420, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)YV12, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)BGR, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(s
 tring)RGB, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1
> >
> >    despite the media pipeline actually being configured for 60fps.
> >
> >    Forcing it by adjusting the pipeline only results in gstreamer
> >    failing, because it believes that v4l2 is unable to operate at
> >    60fps.
> >
> >    Also note the complaints from v4l2src about the non-compliance...
> 
> Thanks, I've fixed most of v4l2-compliance issues, but this is not
> done yet. Is that something you can help with?

I've looked at this, and IMHO it's yet another media control API mess.

- media-ctl itself allows setting the format on subdev pads via
  struct v4l2_subdev_format.

- struct v4l2_subdev_format contains a struct v4l2_mbus_framefmt.

- struct v4l2_mbus_framefmt contains:
  * @width:      frame width
  * @height:     frame height
  * @code:       data format code (from enum v4l2_mbus_pixelcode)
  * @field:      used interlacing type (from enum v4l2_field)
  * @colorspace: colorspace of the data (from enum v4l2_colorspace)
  * @ycbcr_enc:  YCbCr encoding of the data (from enum v4l2_ycbcr_encoding)
  * @quantization: quantization of the data (from enum v4l2_quantization)
  * @xfer_func:  transfer function of the data (from enum v4l2_xfer_func)

- media-ctl sets width, height, code and field, but nothing else.

We're already agreed that the fields that media-ctl are part of the
format negotiation between the ultimate source, flowing down to the
capture device.  However, there's no support in media-ctl to deal
with these other fields - so media-ctl in itself is only half-
implemented.

>From what I can tell, _we_ are doing the right thing in imx-media-capture.

However, I think part of the problem is the set_fmt implementation.
When a source pad is configured via set_fmt(), any fields that can
not be altered (eg, because the subdev doesn't support colorspace
conversion) need to be preserved from the subdev's sink pad.

Right now, CSI doesn't do that - it only looks at the width, height,
code, and field.

I think we've got other bugs though that haven't been picked up by any
review - csi_try_fmt() adjusts the format using the _current_
configuration of the sink pad, even when using V4L2_SUBDEV_FORMAT_TRY.
This seems wrong according to the docs: the purpose of the try
mechanism is to be able to setup the _entire_ pipeline using the TRY
mechanism to work out whether the configuration works, before then
setting for real.  If we're validating the TRY formats against the
live configuration, then we're not doing that.

There's calls for:

v4l2_subdev_get_try_format
v4l2_subdev_get_try_crop
v4l2_subdev_get_try_compose

to get the try configuration - we hardly make use of all of these.  I
would suggest that we change the approach to implementing the various
subdevs such that:

1) like __csi_get_fmt(), we have accessors that gets a pointer to the
   correct state for the TRY/live settings.

2) everywhere we're asked to get or set parameters that can be TRY/live,
   we use these accessors to retrieve a pointer to the correct state to
   not only read, but also modify.

3) when we're evaluating parameters against another pad, we use these
   accessors to obtain the other pad's configuration, rather than poking
   about in the state saved in the subdev's priv-> (which is irrelevant
   for the TRY variant.)

4) ensure that all parameters which the subdev itself does not support
   modification of are correctly propagated from the sink pad to all
   source pads, and are unable to be modified via the source pad.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/19/2017 05:14 AM, Russell King - ARM Linux wrote:
> On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
>> On 03/18/2017 12:22 PM, Russell King - ARM Linux wrote:
>>> 0:00:01.955927879 20954  0x15ffe90 INFO                    v4l2 gstv4l2object.c:3811:gst_v4l2_object_get_caps:<v4l2src0> probed caps: video/x-bayer, format=(string)rggb, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)I420, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)YV12, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)BGR, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)RGB, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1
>>>
>>>     despite the media pipeline actually being configured for 60fps.
>>>
>>>     Forcing it by adjusting the pipeline only results in gstreamer
>>>     failing, because it believes that v4l2 is unable to operate at
>>>     60fps.
>>>
>>>     Also note the complaints from v4l2src about the non-compliance...
>> Thanks, I've fixed most of v4l2-compliance issues, but this is not
>> done yet. Is that something you can help with?
> I've looked at this, and IMHO it's yet another media control API mess.
>
> - media-ctl itself allows setting the format on subdev pads via
>    struct v4l2_subdev_format.
>
> - struct v4l2_subdev_format contains a struct v4l2_mbus_framefmt.
>
> - struct v4l2_mbus_framefmt contains:
>    * @width:      frame width
>    * @height:     frame height
>    * @code:       data format code (from enum v4l2_mbus_pixelcode)
>    * @field:      used interlacing type (from enum v4l2_field)
>    * @colorspace: colorspace of the data (from enum v4l2_colorspace)
>    * @ycbcr_enc:  YCbCr encoding of the data (from enum v4l2_ycbcr_encoding)
>    * @quantization: quantization of the data (from enum v4l2_quantization)
>    * @xfer_func:  transfer function of the data (from enum v4l2_xfer_func)
>
> - media-ctl sets width, height, code and field, but nothing else.
>
> We're already agreed that the fields that media-ctl are part of the
> format negotiation between the ultimate source, flowing down to the
> capture device.  However, there's no support in media-ctl to deal
> with these other fields - so media-ctl in itself is only half-
> implemented.
>
>  From what I can tell, _we_ are doing the right thing in imx-media-capture.
>
> However, I think part of the problem is the set_fmt implementation.
> When a source pad is configured via set_fmt(), any fields that can
> not be altered (eg, because the subdev doesn't support colorspace
> conversion) need to be preserved from the subdev's sink pad.
>
> Right now, CSI doesn't do that - it only looks at the width, height,
> code, and field.

Correct, there is currently no propagation of the colorimetry
parameters (colorspace, ycbcr_enc, quantization, and xfer_func).
For the most part, those are just ignored ATM. Philipp Zabel did
do some work earlier to start propagating those, but that's still
TODO.

>
> I think we've got other bugs though that haven't been picked up by any
> review - csi_try_fmt() adjusts the format using the _current_
> configuration of the sink pad, even when using V4L2_SUBDEV_FORMAT_TRY.
> This seems wrong according to the docs: the purpose of the try
> mechanism is to be able to setup the _entire_ pipeline using the TRY
> mechanism to work out whether the configuration works, before then
> setting for real.  If we're validating the TRY formats against the
> live configuration, then we're not doing that.

I don't believe that is correct. csi_try_fmt() for the source pads calls
__csi_get_fmt(priv, cfg, CSI_SINK_PAD, sdformat->which) to get
the sink format, and for the TRY trial-run from csi_set_fmt(),
sdformat->which will be set to TRY, so the returned sink format
is the TRY format.

But I haven't tested a complete pipeline configuration under the
TRY case, there still could be issues there. But I've checked the
CSI, VDIC, and PRPENCVF subdevs, and for set_fmt() trial-runs,
those should be working correctly using the TRY mechanism.


> There's calls for:
>
> v4l2_subdev_get_try_format
> v4l2_subdev_get_try_crop
> v4l2_subdev_get_try_compose
>
> to get the try configuration - we hardly make use of all of these.

Not sure what you mean, the first two are currently
being used for TRY setup. And I don't think
v4l2_subdev_get_try_compose() is needed.

>   I
> would suggest that we change the approach to implementing the various
> subdevs such that:
>
> 1) like __csi_get_fmt(), we have accessors that gets a pointer to the
>     correct state for the TRY/live settings.

I've verified that CSI, VDIC, and PRPENCVF subdevs do that.

>
> 2) everywhere we're asked to get or set parameters that can be TRY/live,
>     we use these accessors to retrieve a pointer to the correct state to
>     not only read, but also modify.

Yes, that is currently being done in CSI, VDIC, and PRPENCVF subdevs.

>
> 3) when we're evaluating parameters against another pad, we use these
>     accessors to obtain the other pad's configuration, rather than poking
>     about in the state saved in the subdev's priv-> (which is irrelevant
>     for the TRY variant.)

Again, that is being done already:

__vdic_get_fmt()
__prp_get_fmt() (in both prp and prpencvf subdevs)
__csi_get_fmt()


>
> 4) ensure that all parameters which the subdev itself does not support
>     modification of are correctly propagated from the sink pad to all
>     source pads, and are unable to be modified via the source pad.

That is currently true except for the colorimetry params as I mentioned.

Steve

[PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/19/2017 05:14 AM, Russell King - ARM Linux wrote:
> On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
>> On 03/18/2017 12:22 PM, Russell King - ARM Linux wrote:
>>> 0:00:01.955927879 20954  0x15ffe90 INFO                    v4l2 gstv4l2object.c:3811:gst_v4l2_object_get_caps:<v4l2src0> probed caps: video/x-bayer, format=(string)rggb, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)I420, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)YV12, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)BGR, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)RGB, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1
>>>
>>>     despite the media pipeline actually being configured for 60fps.
>>>
>>>     Forcing it by adjusting the pipeline only results in gstreamer
>>>     failing, because it believes that v4l2 is unable to operate at
>>>     60fps.
>>>
>>>     Also note the complaints from v4l2src about the non-compliance...
>> Thanks, I've fixed most of v4l2-compliance issues, but this is not
>> done yet. Is that something you can help with?
> I've looked at this, and IMHO it's yet another media control API mess.
>
> - media-ctl itself allows setting the format on subdev pads via
>    struct v4l2_subdev_format.
>
> - struct v4l2_subdev_format contains a struct v4l2_mbus_framefmt.
>
> - struct v4l2_mbus_framefmt contains:
>    * @width:      frame width
>    * @height:     frame height
>    * @code:       data format code (from enum v4l2_mbus_pixelcode)
>    * @field:      used interlacing type (from enum v4l2_field)
>    * @colorspace: colorspace of the data (from enum v4l2_colorspace)
>    * @ycbcr_enc:  YCbCr encoding of the data (from enum v4l2_ycbcr_encoding)
>    * @quantization: quantization of the data (from enum v4l2_quantization)
>    * @xfer_func:  transfer function of the data (from enum v4l2_xfer_func)
>
> - media-ctl sets width, height, code and field, but nothing else.
>
> We're already agreed that the fields that media-ctl are part of the
> format negotiation between the ultimate source, flowing down to the
> capture device.  However, there's no support in media-ctl to deal
> with these other fields - so media-ctl in itself is only half-
> implemented.
>
>  From what I can tell, _we_ are doing the right thing in imx-media-capture.
>
> However, I think part of the problem is the set_fmt implementation.
> When a source pad is configured via set_fmt(), any fields that can
> not be altered (eg, because the subdev doesn't support colorspace
> conversion) need to be preserved from the subdev's sink pad.
>
> Right now, CSI doesn't do that - it only looks at the width, height,
> code, and field.

Correct, there is currently no propagation of the colorimetry
parameters (colorspace, ycbcr_enc, quantization, and xfer_func).
For the most part, those are just ignored ATM. Philipp Zabel did
do some work earlier to start propagating those, but that's still
TODO.

>
> I think we've got other bugs though that haven't been picked up by any
> review - csi_try_fmt() adjusts the format using the _current_
> configuration of the sink pad, even when using V4L2_SUBDEV_FORMAT_TRY.
> This seems wrong according to the docs: the purpose of the try
> mechanism is to be able to setup the _entire_ pipeline using the TRY
> mechanism to work out whether the configuration works, before then
> setting for real.  If we're validating the TRY formats against the
> live configuration, then we're not doing that.

I don't believe that is correct. csi_try_fmt() for the source pads calls
__csi_get_fmt(priv, cfg, CSI_SINK_PAD, sdformat->which) to get
the sink format, and for the TRY trial-run from csi_set_fmt(),
sdformat->which will be set to TRY, so the returned sink format
is the TRY format.

But I haven't tested a complete pipeline configuration under the
TRY case, there still could be issues there. But I've checked the
CSI, VDIC, and PRPENCVF subdevs, and for set_fmt() trial-runs,
those should be working correctly using the TRY mechanism.


> There's calls for:
>
> v4l2_subdev_get_try_format
> v4l2_subdev_get_try_crop
> v4l2_subdev_get_try_compose
>
> to get the try configuration - we hardly make use of all of these.

Not sure what you mean, the first two are currently
being used for TRY setup. And I don't think
v4l2_subdev_get_try_compose() is needed.

>   I
> would suggest that we change the approach to implementing the various
> subdevs such that:
>
> 1) like __csi_get_fmt(), we have accessors that gets a pointer to the
>     correct state for the TRY/live settings.

I've verified that CSI, VDIC, and PRPENCVF subdevs do that.

>
> 2) everywhere we're asked to get or set parameters that can be TRY/live,
>     we use these accessors to retrieve a pointer to the correct state to
>     not only read, but also modify.

Yes, that is currently being done in CSI, VDIC, and PRPENCVF subdevs.

>
> 3) when we're evaluating parameters against another pad, we use these
>     accessors to obtain the other pad's configuration, rather than poking
>     about in the state saved in the subdev's priv-> (which is irrelevant
>     for the TRY variant.)

Again, that is being done already:

__vdic_get_fmt()
__prp_get_fmt() (in both prp and prpencvf subdevs)
__csi_get_fmt()


>
> 4) ensure that all parameters which the subdev itself does not support
>     modification of are correctly propagated from the sink pad to all
>     source pads, and are unable to be modified via the source pad.

That is currently true except for the colorimetry params as I mentioned.

Steve

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/19/2017 05:14 AM, Russell King - ARM Linux wrote:
> On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
>> On 03/18/2017 12:22 PM, Russell King - ARM Linux wrote:
>>> 0:00:01.955927879 20954  0x15ffe90 INFO                    v4l2 gstv4l2object.c:3811:gst_v4l2_object_get_caps:<v4l2src0> probed caps: video/x-bayer, format=(string)rggb, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)I420, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)YV12, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)BGR, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(
 string)RGB, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1
>>>
>>>     despite the media pipeline actually being configured for 60fps.
>>>
>>>     Forcing it by adjusting the pipeline only results in gstreamer
>>>     failing, because it believes that v4l2 is unable to operate at
>>>     60fps.
>>>
>>>     Also note the complaints from v4l2src about the non-compliance...
>> Thanks, I've fixed most of v4l2-compliance issues, but this is not
>> done yet. Is that something you can help with?
> I've looked at this, and IMHO it's yet another media control API mess.
>
> - media-ctl itself allows setting the format on subdev pads via
>    struct v4l2_subdev_format.
>
> - struct v4l2_subdev_format contains a struct v4l2_mbus_framefmt.
>
> - struct v4l2_mbus_framefmt contains:
>    * @width:      frame width
>    * @height:     frame height
>    * @code:       data format code (from enum v4l2_mbus_pixelcode)
>    * @field:      used interlacing type (from enum v4l2_field)
>    * @colorspace: colorspace of the data (from enum v4l2_colorspace)
>    * @ycbcr_enc:  YCbCr encoding of the data (from enum v4l2_ycbcr_encoding)
>    * @quantization: quantization of the data (from enum v4l2_quantization)
>    * @xfer_func:  transfer function of the data (from enum v4l2_xfer_func)
>
> - media-ctl sets width, height, code and field, but nothing else.
>
> We're already agreed that the fields that media-ctl are part of the
> format negotiation between the ultimate source, flowing down to the
> capture device.  However, there's no support in media-ctl to deal
> with these other fields - so media-ctl in itself is only half-
> implemented.
>
>  From what I can tell, _we_ are doing the right thing in imx-media-capture.
>
> However, I think part of the problem is the set_fmt implementation.
> When a source pad is configured via set_fmt(), any fields that can
> not be altered (eg, because the subdev doesn't support colorspace
> conversion) need to be preserved from the subdev's sink pad.
>
> Right now, CSI doesn't do that - it only looks at the width, height,
> code, and field.

Correct, there is currently no propagation of the colorimetry
parameters (colorspace, ycbcr_enc, quantization, and xfer_func).
For the most part, those are just ignored ATM. Philipp Zabel did
do some work earlier to start propagating those, but that's still
TODO.

>
> I think we've got other bugs though that haven't been picked up by any
> review - csi_try_fmt() adjusts the format using the _current_
> configuration of the sink pad, even when using V4L2_SUBDEV_FORMAT_TRY.
> This seems wrong according to the docs: the purpose of the try
> mechanism is to be able to setup the _entire_ pipeline using the TRY
> mechanism to work out whether the configuration works, before then
> setting for real.  If we're validating the TRY formats against the
> live configuration, then we're not doing that.

I don't believe that is correct. csi_try_fmt() for the source pads calls
__csi_get_fmt(priv, cfg, CSI_SINK_PAD, sdformat->which) to get
the sink format, and for the TRY trial-run from csi_set_fmt(),
sdformat->which will be set to TRY, so the returned sink format
is the TRY format.

But I haven't tested a complete pipeline configuration under the
TRY case, there still could be issues there. But I've checked the
CSI, VDIC, and PRPENCVF subdevs, and for set_fmt() trial-runs,
those should be working correctly using the TRY mechanism.


> There's calls for:
>
> v4l2_subdev_get_try_format
> v4l2_subdev_get_try_crop
> v4l2_subdev_get_try_compose
>
> to get the try configuration - we hardly make use of all of these.

Not sure what you mean, the first two are currently
being used for TRY setup. And I don't think
v4l2_subdev_get_try_compose() is needed.

>   I
> would suggest that we change the approach to implementing the various
> subdevs such that:
>
> 1) like __csi_get_fmt(), we have accessors that gets a pointer to the
>     correct state for the TRY/live settings.

I've verified that CSI, VDIC, and PRPENCVF subdevs do that.

>
> 2) everywhere we're asked to get or set parameters that can be TRY/live,
>     we use these accessors to retrieve a pointer to the correct state to
>     not only read, but also modify.

Yes, that is currently being done in CSI, VDIC, and PRPENCVF subdevs.

>
> 3) when we're evaluating parameters against another pad, we use these
>     accessors to obtain the other pad's configuration, rather than poking
>     about in the state saved in the subdev's priv-> (which is irrelevant
>     for the TRY variant.)

Again, that is being done already:

__vdic_get_fmt()
__prp_get_fmt() (in both prp and prpencvf subdevs)
__csi_get_fmt()


>
> 4) ensure that all parameters which the subdev itself does not support
>     modification of are correctly propagated from the sink pad to all
>     source pads, and are unable to be modified via the source pad.

That is currently true except for the colorimetry params as I mentioned.

Steve

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 19, 2017 at 11:37:15AM -0700, Steve Longerbeam wrote:
> On 03/19/2017 05:14 AM, Russell King - ARM Linux wrote:
> >Right now, CSI doesn't do that - it only looks at the width, height,
> >code, and field.
> 
> Correct, there is currently no propagation of the colorimetry
> parameters (colorspace, ycbcr_enc, quantization, and xfer_func).
> For the most part, those are just ignored ATM. Philipp Zabel did
> do some work earlier to start propagating those, but that's still
> TODO.


> 
> >
> >I think we've got other bugs though that haven't been picked up by any
> >review - csi_try_fmt() adjusts the format using the _current_
> >configuration of the sink pad, even when using V4L2_SUBDEV_FORMAT_TRY.
> >This seems wrong according to the docs: the purpose of the try
> >mechanism is to be able to setup the _entire_ pipeline using the TRY
> >mechanism to work out whether the configuration works, before then
> >setting for real.  If we're validating the TRY formats against the
> >live configuration, then we're not doing that.
> 
> I don't believe that is correct. csi_try_fmt() for the source pads calls
> __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sdformat->which) to get
> the sink format, and for the TRY trial-run from csi_set_fmt(),
> sdformat->which will be set to TRY, so the returned sink format
> is the TRY format.

Look at csi_try_fmt() - it validates the source pad against
priv->crop, which is the actively live cropping rectangle, not the
one which has been configured for the TRY trial-run.

Also, as I mention elsewhere, I believe the way we're doing scaling
is completely wrong...

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 19, 2017 at 11:37:15AM -0700, Steve Longerbeam wrote:
> On 03/19/2017 05:14 AM, Russell King - ARM Linux wrote:
> >Right now, CSI doesn't do that - it only looks at the width, height,
> >code, and field.
> 
> Correct, there is currently no propagation of the colorimetry
> parameters (colorspace, ycbcr_enc, quantization, and xfer_func).
> For the most part, those are just ignored ATM. Philipp Zabel did
> do some work earlier to start propagating those, but that's still
> TODO.


> 
> >
> >I think we've got other bugs though that haven't been picked up by any
> >review - csi_try_fmt() adjusts the format using the _current_
> >configuration of the sink pad, even when using V4L2_SUBDEV_FORMAT_TRY.
> >This seems wrong according to the docs: the purpose of the try
> >mechanism is to be able to setup the _entire_ pipeline using the TRY
> >mechanism to work out whether the configuration works, before then
> >setting for real.  If we're validating the TRY formats against the
> >live configuration, then we're not doing that.
> 
> I don't believe that is correct. csi_try_fmt() for the source pads calls
> __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sdformat->which) to get
> the sink format, and for the TRY trial-run from csi_set_fmt(),
> sdformat->which will be set to TRY, so the returned sink format
> is the TRY format.

Look at csi_try_fmt() - it validates the source pad against
priv->crop, which is the actively live cropping rectangle, not the
one which has been configured for the TRY trial-run.

Also, as I mention elsewhere, I believe the way we're doing scaling
is completely wrong...

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Sun, Mar 19, 2017 at 11:37:15AM -0700, Steve Longerbeam wrote:
> On 03/19/2017 05:14 AM, Russell King - ARM Linux wrote:
> >Right now, CSI doesn't do that - it only looks at the width, height,
> >code, and field.
> 
> Correct, there is currently no propagation of the colorimetry
> parameters (colorspace, ycbcr_enc, quantization, and xfer_func).
> For the most part, those are just ignored ATM. Philipp Zabel did
> do some work earlier to start propagating those, but that's still
> TODO.


> 
> >
> >I think we've got other bugs though that haven't been picked up by any
> >review - csi_try_fmt() adjusts the format using the _current_
> >configuration of the sink pad, even when using V4L2_SUBDEV_FORMAT_TRY.
> >This seems wrong according to the docs: the purpose of the try
> >mechanism is to be able to setup the _entire_ pipeline using the TRY
> >mechanism to work out whether the configuration works, before then
> >setting for real.  If we're validating the TRY formats against the
> >live configuration, then we're not doing that.
> 
> I don't believe that is correct. csi_try_fmt() for the source pads calls
> __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sdformat->which) to get
> the sink format, and for the TRY trial-run from csi_set_fmt(),
> sdformat->which will be set to TRY, so the returned sink format
> is the TRY format.

Look at csi_try_fmt() - it validates the source pad against
priv->crop, which is the actively live cropping rectangle, not the
one which has been configured for the TRY trial-run.

Also, as I mention elsewhere, I believe the way we're doing scaling
is completely wrong...

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/19/2017 11:51 AM, Russell King - ARM Linux wrote:
> On Sun, Mar 19, 2017 at 11:37:15AM -0700, Steve Longerbeam wrote:
>> On 03/19/2017 05:14 AM, Russell King - ARM Linux wrote:
>>> Right now, CSI doesn't do that - it only looks at the width, height,
>>> code, and field.
>> Correct, there is currently no propagation of the colorimetry
>> parameters (colorspace, ycbcr_enc, quantization, and xfer_func).
>> For the most part, those are just ignored ATM. Philipp Zabel did
>> do some work earlier to start propagating those, but that's still
>> TODO.
>
>>> I think we've got other bugs though that haven't been picked up by any
>>> review - csi_try_fmt() adjusts the format using the _current_
>>> configuration of the sink pad, even when using V4L2_SUBDEV_FORMAT_TRY.
>>> This seems wrong according to the docs: the purpose of the try
>>> mechanism is to be able to setup the _entire_ pipeline using the TRY
>>> mechanism to work out whether the configuration works, before then
>>> setting for real.  If we're validating the TRY formats against the
>>> live configuration, then we're not doing that.
>> I don't believe that is correct. csi_try_fmt() for the source pads calls
>> __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sdformat->which) to get
>> the sink format, and for the TRY trial-run from csi_set_fmt(),
>> sdformat->which will be set to TRY, so the returned sink format
>> is the TRY format.
> Look at csi_try_fmt() - it validates the source pad against
> priv->crop, which is the actively live cropping rectangle, not the
> one which has been configured for the TRY trial-run.

Ah yes, crop, I missed that. Yes you are right, looks like we
need to add a __csi_get_crop().

>
> Also, as I mention elsewhere, I believe the way we're doing scaling
> is completely wrong...

You might be right there too. Initially, I had no support for the 
down-scaling
in the CSI. That was added later by Philipp, I will respond with more 
there...

Steve

[PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/19/2017 11:51 AM, Russell King - ARM Linux wrote:
> On Sun, Mar 19, 2017 at 11:37:15AM -0700, Steve Longerbeam wrote:
>> On 03/19/2017 05:14 AM, Russell King - ARM Linux wrote:
>>> Right now, CSI doesn't do that - it only looks at the width, height,
>>> code, and field.
>> Correct, there is currently no propagation of the colorimetry
>> parameters (colorspace, ycbcr_enc, quantization, and xfer_func).
>> For the most part, those are just ignored ATM. Philipp Zabel did
>> do some work earlier to start propagating those, but that's still
>> TODO.
>
>>> I think we've got other bugs though that haven't been picked up by any
>>> review - csi_try_fmt() adjusts the format using the _current_
>>> configuration of the sink pad, even when using V4L2_SUBDEV_FORMAT_TRY.
>>> This seems wrong according to the docs: the purpose of the try
>>> mechanism is to be able to setup the _entire_ pipeline using the TRY
>>> mechanism to work out whether the configuration works, before then
>>> setting for real.  If we're validating the TRY formats against the
>>> live configuration, then we're not doing that.
>> I don't believe that is correct. csi_try_fmt() for the source pads calls
>> __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sdformat->which) to get
>> the sink format, and for the TRY trial-run from csi_set_fmt(),
>> sdformat->which will be set to TRY, so the returned sink format
>> is the TRY format.
> Look at csi_try_fmt() - it validates the source pad against
> priv->crop, which is the actively live cropping rectangle, not the
> one which has been configured for the TRY trial-run.

Ah yes, crop, I missed that. Yes you are right, looks like we
need to add a __csi_get_crop().

>
> Also, as I mention elsewhere, I believe the way we're doing scaling
> is completely wrong...

You might be right there too. Initially, I had no support for the 
down-scaling
in the CSI. That was added later by Philipp, I will respond with more 
there...

Steve

Re: [PATCH v5 00/39] i.MX Media Driver

[Steve Longerbeam]

On 03/19/2017 11:51 AM, Russell King - ARM Linux wrote:
> On Sun, Mar 19, 2017 at 11:37:15AM -0700, Steve Longerbeam wrote:
>> On 03/19/2017 05:14 AM, Russell King - ARM Linux wrote:
>>> Right now, CSI doesn't do that - it only looks at the width, height,
>>> code, and field.
>> Correct, there is currently no propagation of the colorimetry
>> parameters (colorspace, ycbcr_enc, quantization, and xfer_func).
>> For the most part, those are just ignored ATM. Philipp Zabel did
>> do some work earlier to start propagating those, but that's still
>> TODO.
>
>>> I think we've got other bugs though that haven't been picked up by any
>>> review - csi_try_fmt() adjusts the format using the _current_
>>> configuration of the sink pad, even when using V4L2_SUBDEV_FORMAT_TRY.
>>> This seems wrong according to the docs: the purpose of the try
>>> mechanism is to be able to setup the _entire_ pipeline using the TRY
>>> mechanism to work out whether the configuration works, before then
>>> setting for real.  If we're validating the TRY formats against the
>>> live configuration, then we're not doing that.
>> I don't believe that is correct. csi_try_fmt() for the source pads calls
>> __csi_get_fmt(priv, cfg, CSI_SINK_PAD, sdformat->which) to get
>> the sink format, and for the TRY trial-run from csi_set_fmt(),
>> sdformat->which will be set to TRY, so the returned sink format
>> is the TRY format.
> Look at csi_try_fmt() - it validates the source pad against
> priv->crop, which is the actively live cropping rectangle, not the
> one which has been configured for the TRY trial-run.

Ah yes, crop, I missed that. Yes you are right, looks like we
need to add a __csi_get_crop().

>
> Also, as I mention elsewhere, I believe the way we're doing scaling
> is completely wrong...

You might be right there too. Initially, I had no support for the 
down-scaling
in the CSI. That was added later by Philipp, I will respond with more 
there...

Steve

Re: [PATCH v5 00/39] i.MX Media Driver

[Hans Verkuil]

On 03/19/2017 01:14 PM, Russell King - ARM Linux wrote:
> On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
>> On 03/18/2017 12:22 PM, Russell King - ARM Linux wrote:
>>> 0:00:01.955927879 20954  0x15ffe90 INFO                    v4l2 gstv4l2object.c:3811:gst_v4l2_object_get_caps:<v4l2src0> probed caps: video/x-bayer, format=(string)rggb, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)I420, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)YV12, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)BGR, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)RGB, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1
>>>
>>>    despite the media pipeline actually being configured for 60fps.
>>>
>>>    Forcing it by adjusting the pipeline only results in gstreamer
>>>    failing, because it believes that v4l2 is unable to operate at
>>>    60fps.
>>>
>>>    Also note the complaints from v4l2src about the non-compliance...
>>
>> Thanks, I've fixed most of v4l2-compliance issues, but this is not
>> done yet. Is that something you can help with?
> 
> I've looked at this, and IMHO it's yet another media control API mess.
> 
> - media-ctl itself allows setting the format on subdev pads via
>   struct v4l2_subdev_format.
> 
> - struct v4l2_subdev_format contains a struct v4l2_mbus_framefmt.
> 
> - struct v4l2_mbus_framefmt contains:
>   * @width:      frame width
>   * @height:     frame height
>   * @code:       data format code (from enum v4l2_mbus_pixelcode)
>   * @field:      used interlacing type (from enum v4l2_field)
>   * @colorspace: colorspace of the data (from enum v4l2_colorspace)
>   * @ycbcr_enc:  YCbCr encoding of the data (from enum v4l2_ycbcr_encoding)
>   * @quantization: quantization of the data (from enum v4l2_quantization)
>   * @xfer_func:  transfer function of the data (from enum v4l2_xfer_func)
> 
> - media-ctl sets width, height, code and field, but nothing else.
> 
> We're already agreed that the fields that media-ctl are part of the
> format negotiation between the ultimate source, flowing down to the
> capture device.  However, there's no support in media-ctl to deal
> with these other fields - so media-ctl in itself is only half-
> implemented.

Correct. The colorspace et al fields are in practice unimportant for sensors.
For HDMI/DP they are very important, though.

It's the reason why nobody worked on adding support for this to media-ctl,
it's almost exclusively used with sensors. Not saying that it is right that
it hasn't been added to media-ctl, just that it never had a high enough prio.

Regards,

	Hans

> 
> From what I can tell, _we_ are doing the right thing in imx-media-capture.
> 
> However, I think part of the problem is the set_fmt implementation.
> When a source pad is configured via set_fmt(), any fields that can
> not be altered (eg, because the subdev doesn't support colorspace
> conversion) need to be preserved from the subdev's sink pad.
> 
> Right now, CSI doesn't do that - it only looks at the width, height,
> code, and field.
> 
> I think we've got other bugs though that haven't been picked up by any
> review - csi_try_fmt() adjusts the format using the _current_
> configuration of the sink pad, even when using V4L2_SUBDEV_FORMAT_TRY.
> This seems wrong according to the docs: the purpose of the try
> mechanism is to be able to setup the _entire_ pipeline using the TRY
> mechanism to work out whether the configuration works, before then
> setting for real.  If we're validating the TRY formats against the
> live configuration, then we're not doing that.
> 
> There's calls for:
> 
> v4l2_subdev_get_try_format
> v4l2_subdev_get_try_crop
> v4l2_subdev_get_try_compose
> 
> to get the try configuration - we hardly make use of all of these.  I
> would suggest that we change the approach to implementing the various
> subdevs such that:
> 
> 1) like __csi_get_fmt(), we have accessors that gets a pointer to the
>    correct state for the TRY/live settings.
> 
> 2) everywhere we're asked to get or set parameters that can be TRY/live,
>    we use these accessors to retrieve a pointer to the correct state to
>    not only read, but also modify.
> 
> 3) when we're evaluating parameters against another pad, we use these
>    accessors to obtain the other pad's configuration, rather than poking
>    about in the state saved in the subdev's priv-> (which is irrelevant
>    for the TRY variant.)
> 
> 4) ensure that all parameters which the subdev itself does not support
>    modification of are correctly propagated from the sink pad to all
>    source pads, and are unable to be modified via the source pad.
> 

[PATCH v5 00/39] i.MX Media Driver

[Hans Verkuil]

On 03/19/2017 01:14 PM, Russell King - ARM Linux wrote:
> On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
>> On 03/18/2017 12:22 PM, Russell King - ARM Linux wrote:
>>> 0:00:01.955927879 20954  0x15ffe90 INFO                    v4l2 gstv4l2object.c:3811:gst_v4l2_object_get_caps:<v4l2src0> probed caps: video/x-bayer, format=(string)rggb, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)I420, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)YV12, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)BGR, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)RGB, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1
>>>
>>>    despite the media pipeline actually being configured for 60fps.
>>>
>>>    Forcing it by adjusting the pipeline only results in gstreamer
>>>    failing, because it believes that v4l2 is unable to operate at
>>>    60fps.
>>>
>>>    Also note the complaints from v4l2src about the non-compliance...
>>
>> Thanks, I've fixed most of v4l2-compliance issues, but this is not
>> done yet. Is that something you can help with?
> 
> I've looked at this, and IMHO it's yet another media control API mess.
> 
> - media-ctl itself allows setting the format on subdev pads via
>   struct v4l2_subdev_format.
> 
> - struct v4l2_subdev_format contains a struct v4l2_mbus_framefmt.
> 
> - struct v4l2_mbus_framefmt contains:
>   * @width:      frame width
>   * @height:     frame height
>   * @code:       data format code (from enum v4l2_mbus_pixelcode)
>   * @field:      used interlacing type (from enum v4l2_field)
>   * @colorspace: colorspace of the data (from enum v4l2_colorspace)
>   * @ycbcr_enc:  YCbCr encoding of the data (from enum v4l2_ycbcr_encoding)
>   * @quantization: quantization of the data (from enum v4l2_quantization)
>   * @xfer_func:  transfer function of the data (from enum v4l2_xfer_func)
> 
> - media-ctl sets width, height, code and field, but nothing else.
> 
> We're already agreed that the fields that media-ctl are part of the
> format negotiation between the ultimate source, flowing down to the
> capture device.  However, there's no support in media-ctl to deal
> with these other fields - so media-ctl in itself is only half-
> implemented.

Correct. The colorspace et al fields are in practice unimportant for sensors.
For HDMI/DP they are very important, though.

It's the reason why nobody worked on adding support for this to media-ctl,
it's almost exclusively used with sensors. Not saying that it is right that
it hasn't been added to media-ctl, just that it never had a high enough prio.

Regards,

	Hans

> 
> From what I can tell, _we_ are doing the right thing in imx-media-capture.
> 
> However, I think part of the problem is the set_fmt implementation.
> When a source pad is configured via set_fmt(), any fields that can
> not be altered (eg, because the subdev doesn't support colorspace
> conversion) need to be preserved from the subdev's sink pad.
> 
> Right now, CSI doesn't do that - it only looks at the width, height,
> code, and field.
> 
> I think we've got other bugs though that haven't been picked up by any
> review - csi_try_fmt() adjusts the format using the _current_
> configuration of the sink pad, even when using V4L2_SUBDEV_FORMAT_TRY.
> This seems wrong according to the docs: the purpose of the try
> mechanism is to be able to setup the _entire_ pipeline using the TRY
> mechanism to work out whether the configuration works, before then
> setting for real.  If we're validating the TRY formats against the
> live configuration, then we're not doing that.
> 
> There's calls for:
> 
> v4l2_subdev_get_try_format
> v4l2_subdev_get_try_crop
> v4l2_subdev_get_try_compose
> 
> to get the try configuration - we hardly make use of all of these.  I
> would suggest that we change the approach to implementing the various
> subdevs such that:
> 
> 1) like __csi_get_fmt(), we have accessors that gets a pointer to the
>    correct state for the TRY/live settings.
> 
> 2) everywhere we're asked to get or set parameters that can be TRY/live,
>    we use these accessors to retrieve a pointer to the correct state to
>    not only read, but also modify.
> 
> 3) when we're evaluating parameters against another pad, we use these
>    accessors to obtain the other pad's configuration, rather than poking
>    about in the state saved in the subdev's priv-> (which is irrelevant
>    for the TRY variant.)
> 
> 4) ensure that all parameters which the subdev itself does not support
>    modification of are correctly propagated from the sink pad to all
>    source pads, and are unable to be modified via the source pad.
> 

Re: [PATCH v5 00/39] i.MX Media Driver

[Hans Verkuil]

On 03/19/2017 01:14 PM, Russell King - ARM Linux wrote:
> On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
>> On 03/18/2017 12:22 PM, Russell King - ARM Linux wrote:
>>> 0:00:01.955927879 20954  0x15ffe90 INFO                    v4l2 gstv4l2object.c:3811:gst_v4l2_object_get_caps:<v4l2src0> probed caps: video/x-bayer, format=(string)rggb, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)I420, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)YV12, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)BGR, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(
 string)RGB, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1
>>>
>>>    despite the media pipeline actually being configured for 60fps.
>>>
>>>    Forcing it by adjusting the pipeline only results in gstreamer
>>>    failing, because it believes that v4l2 is unable to operate at
>>>    60fps.
>>>
>>>    Also note the complaints from v4l2src about the non-compliance...
>>
>> Thanks, I've fixed most of v4l2-compliance issues, but this is not
>> done yet. Is that something you can help with?
> 
> I've looked at this, and IMHO it's yet another media control API mess.
> 
> - media-ctl itself allows setting the format on subdev pads via
>   struct v4l2_subdev_format.
> 
> - struct v4l2_subdev_format contains a struct v4l2_mbus_framefmt.
> 
> - struct v4l2_mbus_framefmt contains:
>   * @width:      frame width
>   * @height:     frame height
>   * @code:       data format code (from enum v4l2_mbus_pixelcode)
>   * @field:      used interlacing type (from enum v4l2_field)
>   * @colorspace: colorspace of the data (from enum v4l2_colorspace)
>   * @ycbcr_enc:  YCbCr encoding of the data (from enum v4l2_ycbcr_encoding)
>   * @quantization: quantization of the data (from enum v4l2_quantization)
>   * @xfer_func:  transfer function of the data (from enum v4l2_xfer_func)
> 
> - media-ctl sets width, height, code and field, but nothing else.
> 
> We're already agreed that the fields that media-ctl are part of the
> format negotiation between the ultimate source, flowing down to the
> capture device.  However, there's no support in media-ctl to deal
> with these other fields - so media-ctl in itself is only half-
> implemented.

Correct. The colorspace et al fields are in practice unimportant for sensors.
For HDMI/DP they are very important, though.

It's the reason why nobody worked on adding support for this to media-ctl,
it's almost exclusively used with sensors. Not saying that it is right that
it hasn't been added to media-ctl, just that it never had a high enough prio.

Regards,

	Hans

> 
> From what I can tell, _we_ are doing the right thing in imx-media-capture.
> 
> However, I think part of the problem is the set_fmt implementation.
> When a source pad is configured via set_fmt(), any fields that can
> not be altered (eg, because the subdev doesn't support colorspace
> conversion) need to be preserved from the subdev's sink pad.
> 
> Right now, CSI doesn't do that - it only looks at the width, height,
> code, and field.
> 
> I think we've got other bugs though that haven't been picked up by any
> review - csi_try_fmt() adjusts the format using the _current_
> configuration of the sink pad, even when using V4L2_SUBDEV_FORMAT_TRY.
> This seems wrong according to the docs: the purpose of the try
> mechanism is to be able to setup the _entire_ pipeline using the TRY
> mechanism to work out whether the configuration works, before then
> setting for real.  If we're validating the TRY formats against the
> live configuration, then we're not doing that.
> 
> There's calls for:
> 
> v4l2_subdev_get_try_format
> v4l2_subdev_get_try_crop
> v4l2_subdev_get_try_compose
> 
> to get the try configuration - we hardly make use of all of these.  I
> would suggest that we change the approach to implementing the various
> subdevs such that:
> 
> 1) like __csi_get_fmt(), we have accessors that gets a pointer to the
>    correct state for the TRY/live settings.
> 
> 2) everywhere we're asked to get or set parameters that can be TRY/live,
>    we use these accessors to retrieve a pointer to the correct state to
>    not only read, but also modify.
> 
> 3) when we're evaluating parameters against another pad, we use these
>    accessors to obtain the other pad's configuration, rather than poking
>    about in the state saved in the subdev's priv-> (which is irrelevant
>    for the TRY variant.)
> 
> 4) ensure that all parameters which the subdev itself does not support
>    modification of are correctly propagated from the sink pad to all
>    source pads, and are unable to be modified via the source pad.
> 

Re: [PATCH v5 00/39] i.MX Media Driver

[Philipp Zabel]

On Sun, 2017-03-19 at 12:14 +0000, Russell King - ARM Linux wrote:
> On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> > On 03/18/2017 12:22 PM, Russell King - ARM Linux wrote:
> > >0:00:01.955927879 20954  0x15ffe90 INFO                    v4l2 gstv4l2object.c:3811:gst_v4l2_object_get_caps:<v4l2src0> probed caps: video/x-bayer, format=(string)rggb, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)I420, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)YV12, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)BGR, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)RGB, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1
> > >
> > >    despite the media pipeline actually being configured for 60fps.
> > >
> > >    Forcing it by adjusting the pipeline only results in gstreamer
> > >    failing, because it believes that v4l2 is unable to operate at
> > >    60fps.
> > >
> > >    Also note the complaints from v4l2src about the non-compliance...
> > 
> > Thanks, I've fixed most of v4l2-compliance issues, but this is not
> > done yet. Is that something you can help with?
> 
> I've looked at this, and IMHO it's yet another media control API mess.
> 
> - media-ctl itself allows setting the format on subdev pads via
>   struct v4l2_subdev_format.
> 
> - struct v4l2_subdev_format contains a struct v4l2_mbus_framefmt.
> 
> - struct v4l2_mbus_framefmt contains:
>   * @width:      frame width
>   * @height:     frame height
>   * @code:       data format code (from enum v4l2_mbus_pixelcode)
>   * @field:      used interlacing type (from enum v4l2_field)
>   * @colorspace: colorspace of the data (from enum v4l2_colorspace)
>   * @ycbcr_enc:  YCbCr encoding of the data (from enum v4l2_ycbcr_encoding)
>   * @quantization: quantization of the data (from enum v4l2_quantization)
>   * @xfer_func:  transfer function of the data (from enum v4l2_xfer_func)
> 
> - media-ctl sets width, height, code and field, but nothing else.
> 
> We're already agreed that the fields that media-ctl are part of the
> format negotiation between the ultimate source, flowing down to the
> capture device.  However, there's no support in media-ctl to deal
> with these other fields - so media-ctl in itself is only half-
> implemented.

To set and read colorimetry information:
https://patchwork.linuxtv.org/patch/39350/

regards
Philipp

[PATCH v5 00/39] i.MX Media Driver

[Philipp Zabel]

On Sun, 2017-03-19 at 12:14 +0000, Russell King - ARM Linux wrote:
> On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> > On 03/18/2017 12:22 PM, Russell King - ARM Linux wrote:
> > >0:00:01.955927879 20954  0x15ffe90 INFO                    v4l2 gstv4l2object.c:3811:gst_v4l2_object_get_caps:<v4l2src0> probed caps: video/x-bayer, format=(string)rggb, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)I420, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)YV12, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)BGR, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)RGB, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1
> > >
> > >    despite the media pipeline actually being configured for 60fps.
> > >
> > >    Forcing it by adjusting the pipeline only results in gstreamer
> > >    failing, because it believes that v4l2 is unable to operate at
> > >    60fps.
> > >
> > >    Also note the complaints from v4l2src about the non-compliance...
> > 
> > Thanks, I've fixed most of v4l2-compliance issues, but this is not
> > done yet. Is that something you can help with?
> 
> I've looked at this, and IMHO it's yet another media control API mess.
> 
> - media-ctl itself allows setting the format on subdev pads via
>   struct v4l2_subdev_format.
> 
> - struct v4l2_subdev_format contains a struct v4l2_mbus_framefmt.
> 
> - struct v4l2_mbus_framefmt contains:
>   * @width:      frame width
>   * @height:     frame height
>   * @code:       data format code (from enum v4l2_mbus_pixelcode)
>   * @field:      used interlacing type (from enum v4l2_field)
>   * @colorspace: colorspace of the data (from enum v4l2_colorspace)
>   * @ycbcr_enc:  YCbCr encoding of the data (from enum v4l2_ycbcr_encoding)
>   * @quantization: quantization of the data (from enum v4l2_quantization)
>   * @xfer_func:  transfer function of the data (from enum v4l2_xfer_func)
> 
> - media-ctl sets width, height, code and field, but nothing else.
> 
> We're already agreed that the fields that media-ctl are part of the
> format negotiation between the ultimate source, flowing down to the
> capture device.  However, there's no support in media-ctl to deal
> with these other fields - so media-ctl in itself is only half-
> implemented.

To set and read colorimetry information:
https://patchwork.linuxtv.org/patch/39350/

regards
Philipp

Re: [PATCH v5 00/39] i.MX Media Driver

[Philipp Zabel]

On Sun, 2017-03-19 at 12:14 +0000, Russell King - ARM Linux wrote:
> On Sat, Mar 18, 2017 at 12:58:27PM -0700, Steve Longerbeam wrote:
> > On 03/18/2017 12:22 PM, Russell King - ARM Linux wrote:
> > >0:00:01.955927879 20954  0x15ffe90 INFO                    v4l2 gstv4l2object.c:3811:gst_v4l2_object_get_caps:<v4l2src0> probed caps: video/x-bayer, format=(string)rggb, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)I420, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)YV12, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=(string)BGR, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1; video/x-raw, format=
 (string)RGB, framerate=(fraction)30000/1001, width=(int)816, height=(int)616, interlace-mode=(string)progressive, pixel-aspect-ratio=(fraction)1/1
> > >
> > >    despite the media pipeline actually being configured for 60fps.
> > >
> > >    Forcing it by adjusting the pipeline only results in gstreamer
> > >    failing, because it believes that v4l2 is unable to operate at
> > >    60fps.
> > >
> > >    Also note the complaints from v4l2src about the non-compliance...
> > 
> > Thanks, I've fixed most of v4l2-compliance issues, but this is not
> > done yet. Is that something you can help with?
> 
> I've looked at this, and IMHO it's yet another media control API mess.
> 
> - media-ctl itself allows setting the format on subdev pads via
>   struct v4l2_subdev_format.
> 
> - struct v4l2_subdev_format contains a struct v4l2_mbus_framefmt.
> 
> - struct v4l2_mbus_framefmt contains:
>   * @width:      frame width
>   * @height:     frame height
>   * @code:       data format code (from enum v4l2_mbus_pixelcode)
>   * @field:      used interlacing type (from enum v4l2_field)
>   * @colorspace: colorspace of the data (from enum v4l2_colorspace)
>   * @ycbcr_enc:  YCbCr encoding of the data (from enum v4l2_ycbcr_encoding)
>   * @quantization: quantization of the data (from enum v4l2_quantization)
>   * @xfer_func:  transfer function of the data (from enum v4l2_xfer_func)
> 
> - media-ctl sets width, height, code and field, but nothing else.
> 
> We're already agreed that the fields that media-ctl are part of the
> format negotiation between the ultimate source, flowing down to the
> capture device.  However, there's no support in media-ctl to deal
> with these other fields - so media-ctl in itself is only half-
> implemented.

To set and read colorimetry information:
https://patchwork.linuxtv.org/patch/39350/

regards
Philipp

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 02:20:16PM +0100, Philipp Zabel wrote:
> To set and read colorimetry information:
> https://patchwork.linuxtv.org/patch/39350/

Thanks, I've applied all four of your patches, but there's a side effect
from that.  Old media-ctl (modified by me):

- entity 53: imx219 0-0010 (2 pads, 2 links)
             type V4L2 subdev subtype Unknown flags 0
             device node name /dev/v4l-subdev9
        pad0: Source
                [fmt:SRGGB8/816x616 field:none
                 frame_interval:1/25]
                -> "imx6-mipi-csi2":0 [ENABLED]
        pad1: Sink
                [fmt:SRGGB10/3280x2464 field:none
                 crop.bounds:(0,0)/3280x2464
                 crop:(0,0)/3264x2464
                 compose.bounds:(0,0)/3264x2464
                 compose:(0,0)/816x616]
                <- "imx219 pixel 0-0010":0 [ENABLED,IMMUTABLE]

New media-ctl:

- entity 53: imx219 0-0010 (2 pads, 2 links)
             type V4L2 subdev subtype Unknown flags 0
             device node name /dev/v4l-subdev9
        pad0: Source
                [fmt:SRGGB8_1X8/816x616@1/25 field:none colorspace:srgb xfer:srgb]
                -> "imx6-mipi-csi2":0 [ENABLED]
        pad1: Sink
                <- "imx219 pixel 0-0010":0 [ENABLED,IMMUTABLE]

It looks like we successfully retrieve the frame interval for pad 0
and print it, but when we try to retrieve the frame interval for pad 1,
we get EINVAL (because that's what I'm returning, but I'm wondering if
that's the correct thing to do...) and that prevents _all_ format
information being output.

Maybe something like the following would be a better idea?

 utils/media-ctl/media-ctl.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/utils/media-ctl/media-ctl.c b/utils/media-ctl/media-ctl.c
index f61963a..a50a559 100644
--- a/utils/media-ctl/media-ctl.c
+++ b/utils/media-ctl/media-ctl.c
@@ -81,22 +81,22 @@ static void v4l2_subdev_print_format(struct media_entity *entity,
 	struct v4l2_mbus_framefmt format;
 	struct v4l2_fract interval = { 0, 0 };
 	struct v4l2_rect rect;
-	int ret;
+	int ret, err_fi;
 
 	ret = v4l2_subdev_get_format(entity, &format, pad, which);
 	if (ret != 0)
 		return;
 
-	ret = v4l2_subdev_get_frame_interval(entity, &interval, pad);
-	if (ret != 0 && ret != -ENOTTY)
-		return;
+	err_fi = v4l2_subdev_get_frame_interval(entity, &interval, pad);
 
 	printf("\t\t[fmt:%s/%ux%u",
 	       v4l2_subdev_pixelcode_to_string(format.code),
 	       format.width, format.height);
 
-	if (interval.numerator || interval.denominator)
+	if (err_fi == 0 && (interval.numerator || interval.denominator))
 		printf("@%u/%u", interval.numerator, interval.denominator);
+	else if (err_fi != -ENOTTY)
+		printf("@<error: %s>", strerror(-err_fi));
 
 	if (format.field)
 		printf(" field:%s", v4l2_subdev_field_to_string(format.field));


-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 02:20:16PM +0100, Philipp Zabel wrote:
> To set and read colorimetry information:
> https://patchwork.linuxtv.org/patch/39350/

Thanks, I've applied all four of your patches, but there's a side effect
from that.  Old media-ctl (modified by me):

- entity 53: imx219 0-0010 (2 pads, 2 links)
             type V4L2 subdev subtype Unknown flags 0
             device node name /dev/v4l-subdev9
        pad0: Source
                [fmt:SRGGB8/816x616 field:none
                 frame_interval:1/25]
                -> "imx6-mipi-csi2":0 [ENABLED]
        pad1: Sink
                [fmt:SRGGB10/3280x2464 field:none
                 crop.bounds:(0,0)/3280x2464
                 crop:(0,0)/3264x2464
                 compose.bounds:(0,0)/3264x2464
                 compose:(0,0)/816x616]
                <- "imx219 pixel 0-0010":0 [ENABLED,IMMUTABLE]

New media-ctl:

- entity 53: imx219 0-0010 (2 pads, 2 links)
             type V4L2 subdev subtype Unknown flags 0
             device node name /dev/v4l-subdev9
        pad0: Source
                [fmt:SRGGB8_1X8/816x616@1/25 field:none colorspace:srgb xfer:srgb]
                -> "imx6-mipi-csi2":0 [ENABLED]
        pad1: Sink
                <- "imx219 pixel 0-0010":0 [ENABLED,IMMUTABLE]

It looks like we successfully retrieve the frame interval for pad 0
and print it, but when we try to retrieve the frame interval for pad 1,
we get EINVAL (because that's what I'm returning, but I'm wondering if
that's the correct thing to do...) and that prevents _all_ format
information being output.

Maybe something like the following would be a better idea?

 utils/media-ctl/media-ctl.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/utils/media-ctl/media-ctl.c b/utils/media-ctl/media-ctl.c
index f61963a..a50a559 100644
--- a/utils/media-ctl/media-ctl.c
+++ b/utils/media-ctl/media-ctl.c
@@ -81,22 +81,22 @@ static void v4l2_subdev_print_format(struct media_entity *entity,
 	struct v4l2_mbus_framefmt format;
 	struct v4l2_fract interval = { 0, 0 };
 	struct v4l2_rect rect;
-	int ret;
+	int ret, err_fi;
 
 	ret = v4l2_subdev_get_format(entity, &format, pad, which);
 	if (ret != 0)
 		return;
 
-	ret = v4l2_subdev_get_frame_interval(entity, &interval, pad);
-	if (ret != 0 && ret != -ENOTTY)
-		return;
+	err_fi = v4l2_subdev_get_frame_interval(entity, &interval, pad);
 
 	printf("\t\t[fmt:%s/%ux%u",
 	       v4l2_subdev_pixelcode_to_string(format.code),
 	       format.width, format.height);
 
-	if (interval.numerator || interval.denominator)
+	if (err_fi == 0 && (interval.numerator || interval.denominator))
 		printf("@%u/%u", interval.numerator, interval.denominator);
+	else if (err_fi != -ENOTTY)
+		printf("@<error: %s>", strerror(-err_fi));
 
 	if (format.field)
 		printf(" field:%s", v4l2_subdev_field_to_string(format.field));


-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 02:20:16PM +0100, Philipp Zabel wrote:
> To set and read colorimetry information:
> https://patchwork.linuxtv.org/patch/39350/

Thanks, I've applied all four of your patches, but there's a side effect
from that.  Old media-ctl (modified by me):

- entity 53: imx219 0-0010 (2 pads, 2 links)
             type V4L2 subdev subtype Unknown flags 0
             device node name /dev/v4l-subdev9
        pad0: Source
                [fmt:SRGGB8/816x616 field:none
                 frame_interval:1/25]
                -> "imx6-mipi-csi2":0 [ENABLED]
        pad1: Sink
                [fmt:SRGGB10/3280x2464 field:none
                 crop.bounds:(0,0)/3280x2464
                 crop:(0,0)/3264x2464
                 compose.bounds:(0,0)/3264x2464
                 compose:(0,0)/816x616]
                <- "imx219 pixel 0-0010":0 [ENABLED,IMMUTABLE]

New media-ctl:

- entity 53: imx219 0-0010 (2 pads, 2 links)
             type V4L2 subdev subtype Unknown flags 0
             device node name /dev/v4l-subdev9
        pad0: Source
                [fmt:SRGGB8_1X8/816x616@1/25 field:none colorspace:srgb xfer:srgb]
                -> "imx6-mipi-csi2":0 [ENABLED]
        pad1: Sink
                <- "imx219 pixel 0-0010":0 [ENABLED,IMMUTABLE]

It looks like we successfully retrieve the frame interval for pad 0
and print it, but when we try to retrieve the frame interval for pad 1,
we get EINVAL (because that's what I'm returning, but I'm wondering if
that's the correct thing to do...) and that prevents _all_ format
information being output.

Maybe something like the following would be a better idea?

 utils/media-ctl/media-ctl.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/utils/media-ctl/media-ctl.c b/utils/media-ctl/media-ctl.c
index f61963a..a50a559 100644
--- a/utils/media-ctl/media-ctl.c
+++ b/utils/media-ctl/media-ctl.c
@@ -81,22 +81,22 @@ static void v4l2_subdev_print_format(struct media_entity *entity,
 	struct v4l2_mbus_framefmt format;
 	struct v4l2_fract interval = { 0, 0 };
 	struct v4l2_rect rect;
-	int ret;
+	int ret, err_fi;
 
 	ret = v4l2_subdev_get_format(entity, &format, pad, which);
 	if (ret != 0)
 		return;
 
-	ret = v4l2_subdev_get_frame_interval(entity, &interval, pad);
-	if (ret != 0 && ret != -ENOTTY)
-		return;
+	err_fi = v4l2_subdev_get_frame_interval(entity, &interval, pad);
 
 	printf("\t\t[fmt:%s/%ux%u",
 	       v4l2_subdev_pixelcode_to_string(format.code),
 	       format.width, format.height);
 
-	if (interval.numerator || interval.denominator)
+	if (err_fi == 0 && (interval.numerator || interval.denominator))
 		printf("@%u/%u", interval.numerator, interval.denominator);
+	else if (err_fi != -ENOTTY)
+		printf("@<error: %s>", strerror(-err_fi));
 
 	if (format.field)
 		printf(" field:%s", v4l2_subdev_field_to_string(format.field));


-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Philipp Zabel]

On Mon, 2017-03-20 at 15:43 +0000, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 02:20:16PM +0100, Philipp Zabel wrote:
> > To set and read colorimetry information:
> > https://patchwork.linuxtv.org/patch/39350/
> 
> Thanks, I've applied all four of your patches, but there's a side effect
> from that.  Old media-ctl (modified by me):
> 
> - entity 53: imx219 0-0010 (2 pads, 2 links)
>              type V4L2 subdev subtype Unknown flags 0
>              device node name /dev/v4l-subdev9
>         pad0: Source
>                 [fmt:SRGGB8/816x616 field:none
>                  frame_interval:1/25]
>                 -> "imx6-mipi-csi2":0 [ENABLED]
>         pad1: Sink
>                 [fmt:SRGGB10/3280x2464 field:none
>                  crop.bounds:(0,0)/3280x2464
>                  crop:(0,0)/3264x2464
>                  compose.bounds:(0,0)/3264x2464
>                  compose:(0,0)/816x616]
>                 <- "imx219 pixel 0-0010":0 [ENABLED,IMMUTABLE]
> 
> New media-ctl:
> 
> - entity 53: imx219 0-0010 (2 pads, 2 links)
>              type V4L2 subdev subtype Unknown flags 0
>              device node name /dev/v4l-subdev9
>         pad0: Source
>                 [fmt:SRGGB8_1X8/816x616@1/25 field:none colorspace:srgb xfer:srgb]
>                 -> "imx6-mipi-csi2":0 [ENABLED]
>         pad1: Sink
>                 <- "imx219 pixel 0-0010":0 [ENABLED,IMMUTABLE]
> 
> It looks like we successfully retrieve the frame interval for pad 0
> and print it, but when we try to retrieve the frame interval for pad 1,
> we get EINVAL (because that's what I'm returning, but I'm wondering if
> that's the correct thing to do...) and that prevents _all_ format
> information being output.

According to the documentation [1], you are doing the right thing:

    The struct v4l2_subdev_frame_interval pad references a non-existing
    pad, or the pad doesn’t support frame intervals.

But v4l2_subdev_call returns -ENOIOCTLCMD if the g_frame_interval op is
not implemented at all, which is turned into -ENOTTY by video_usercopy.

[1] https://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/vidioc-subdev-g-frame-interval.html#return-value

> Maybe something like the following would be a better idea?
> 
>  utils/media-ctl/media-ctl.c | 10 +++++-----
>  1 file changed, 5 insertions(+), 5 deletions(-)
> 
> diff --git a/utils/media-ctl/media-ctl.c b/utils/media-ctl/media-ctl.c
> index f61963a..a50a559 100644
> --- a/utils/media-ctl/media-ctl.c
> +++ b/utils/media-ctl/media-ctl.c
> @@ -81,22 +81,22 @@ static void v4l2_subdev_print_format(struct media_entity *entity,
>  	struct v4l2_mbus_framefmt format;
>  	struct v4l2_fract interval = { 0, 0 };
>  	struct v4l2_rect rect;
> -	int ret;
> +	int ret, err_fi;
>  
>  	ret = v4l2_subdev_get_format(entity, &format, pad, which);
>  	if (ret != 0)
>  		return;
>  
> -	ret = v4l2_subdev_get_frame_interval(entity, &interval, pad);
> -	if (ret != 0 && ret != -ENOTTY)
> -		return;
> +	err_fi = v4l2_subdev_get_frame_interval(entity, &interval, pad);

Not supporting frame intervals doesn't warrant a visible error message,
I think -EINVAL should also be ignored above, if the spec is to be
believed.

>  
>  	printf("\t\t[fmt:%s/%ux%u",
>  	       v4l2_subdev_pixelcode_to_string(format.code),
>  	       format.width, format.height);
>  
> -	if (interval.numerator || interval.denominator)
> +	if (err_fi == 0 && (interval.numerator || interval.denominator))
>  		printf("@%u/%u", interval.numerator, interval.denominator);
> +	else if (err_fi != -ENOTTY)
> +		printf("@<error: %s>", strerror(-err_fi));

Or here.

>  
>  	if (format.field)
>  		printf(" field:%s", v4l2_subdev_field_to_string(format.field));
> 
> 

regards
Philipp

[PATCH v5 00/39] i.MX Media Driver

[Philipp Zabel]

On Mon, 2017-03-20 at 15:43 +0000, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 02:20:16PM +0100, Philipp Zabel wrote:
> > To set and read colorimetry information:
> > https://patchwork.linuxtv.org/patch/39350/
> 
> Thanks, I've applied all four of your patches, but there's a side effect
> from that.  Old media-ctl (modified by me):
> 
> - entity 53: imx219 0-0010 (2 pads, 2 links)
>              type V4L2 subdev subtype Unknown flags 0
>              device node name /dev/v4l-subdev9
>         pad0: Source
>                 [fmt:SRGGB8/816x616 field:none
>                  frame_interval:1/25]
>                 -> "imx6-mipi-csi2":0 [ENABLED]
>         pad1: Sink
>                 [fmt:SRGGB10/3280x2464 field:none
>                  crop.bounds:(0,0)/3280x2464
>                  crop:(0,0)/3264x2464
>                  compose.bounds:(0,0)/3264x2464
>                  compose:(0,0)/816x616]
>                 <- "imx219 pixel 0-0010":0 [ENABLED,IMMUTABLE]
> 
> New media-ctl:
> 
> - entity 53: imx219 0-0010 (2 pads, 2 links)
>              type V4L2 subdev subtype Unknown flags 0
>              device node name /dev/v4l-subdev9
>         pad0: Source
>                 [fmt:SRGGB8_1X8/816x616 at 1/25 field:none colorspace:srgb xfer:srgb]
>                 -> "imx6-mipi-csi2":0 [ENABLED]
>         pad1: Sink
>                 <- "imx219 pixel 0-0010":0 [ENABLED,IMMUTABLE]
> 
> It looks like we successfully retrieve the frame interval for pad 0
> and print it, but when we try to retrieve the frame interval for pad 1,
> we get EINVAL (because that's what I'm returning, but I'm wondering if
> that's the correct thing to do...) and that prevents _all_ format
> information being output.

According to the documentation [1], you are doing the right thing:

    The struct v4l2_subdev_frame_interval pad references a non-existing
    pad, or the pad doesn?t support frame intervals.

But v4l2_subdev_call returns -ENOIOCTLCMD if the g_frame_interval op is
not implemented at all, which is turned into -ENOTTY by video_usercopy.

[1] https://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/vidioc-subdev-g-frame-interval.html#return-value

> Maybe something like the following would be a better idea?
> 
>  utils/media-ctl/media-ctl.c | 10 +++++-----
>  1 file changed, 5 insertions(+), 5 deletions(-)
> 
> diff --git a/utils/media-ctl/media-ctl.c b/utils/media-ctl/media-ctl.c
> index f61963a..a50a559 100644
> --- a/utils/media-ctl/media-ctl.c
> +++ b/utils/media-ctl/media-ctl.c
> @@ -81,22 +81,22 @@ static void v4l2_subdev_print_format(struct media_entity *entity,
>  	struct v4l2_mbus_framefmt format;
>  	struct v4l2_fract interval = { 0, 0 };
>  	struct v4l2_rect rect;
> -	int ret;
> +	int ret, err_fi;
>  
>  	ret = v4l2_subdev_get_format(entity, &format, pad, which);
>  	if (ret != 0)
>  		return;
>  
> -	ret = v4l2_subdev_get_frame_interval(entity, &interval, pad);
> -	if (ret != 0 && ret != -ENOTTY)
> -		return;
> +	err_fi = v4l2_subdev_get_frame_interval(entity, &interval, pad);

Not supporting frame intervals doesn't warrant a visible error message,
I think -EINVAL should also be ignored above, if the spec is to be
believed.

>  
>  	printf("\t\t[fmt:%s/%ux%u",
>  	       v4l2_subdev_pixelcode_to_string(format.code),
>  	       format.width, format.height);
>  
> -	if (interval.numerator || interval.denominator)
> +	if (err_fi == 0 && (interval.numerator || interval.denominator))
>  		printf("@%u/%u", interval.numerator, interval.denominator);
> +	else if (err_fi != -ENOTTY)
> +		printf("@<error: %s>", strerror(-err_fi));

Or here.

>  
>  	if (format.field)
>  		printf(" field:%s", v4l2_subdev_field_to_string(format.field));
> 
> 

regards
Philipp

Re: [PATCH v5 00/39] i.MX Media Driver

[Philipp Zabel]

On Mon, 2017-03-20 at 15:43 +0000, Russell King - ARM Linux wrote:
> On Mon, Mar 20, 2017 at 02:20:16PM +0100, Philipp Zabel wrote:
> > To set and read colorimetry information:
> > https://patchwork.linuxtv.org/patch/39350/
> 
> Thanks, I've applied all four of your patches, but there's a side effect
> from that.  Old media-ctl (modified by me):
> 
> - entity 53: imx219 0-0010 (2 pads, 2 links)
>              type V4L2 subdev subtype Unknown flags 0
>              device node name /dev/v4l-subdev9
>         pad0: Source
>                 [fmt:SRGGB8/816x616 field:none
>                  frame_interval:1/25]
>                 -> "imx6-mipi-csi2":0 [ENABLED]
>         pad1: Sink
>                 [fmt:SRGGB10/3280x2464 field:none
>                  crop.bounds:(0,0)/3280x2464
>                  crop:(0,0)/3264x2464
>                  compose.bounds:(0,0)/3264x2464
>                  compose:(0,0)/816x616]
>                 <- "imx219 pixel 0-0010":0 [ENABLED,IMMUTABLE]
> 
> New media-ctl:
> 
> - entity 53: imx219 0-0010 (2 pads, 2 links)
>              type V4L2 subdev subtype Unknown flags 0
>              device node name /dev/v4l-subdev9
>         pad0: Source
>                 [fmt:SRGGB8_1X8/816x616@1/25 field:none colorspace:srgb xfer:srgb]
>                 -> "imx6-mipi-csi2":0 [ENABLED]
>         pad1: Sink
>                 <- "imx219 pixel 0-0010":0 [ENABLED,IMMUTABLE]
> 
> It looks like we successfully retrieve the frame interval for pad 0
> and print it, but when we try to retrieve the frame interval for pad 1,
> we get EINVAL (because that's what I'm returning, but I'm wondering if
> that's the correct thing to do...) and that prevents _all_ format
> information being output.

According to the documentation [1], you are doing the right thing:

    The struct v4l2_subdev_frame_interval pad references a non-existing
    pad, or the pad doesn’t support frame intervals.

But v4l2_subdev_call returns -ENOIOCTLCMD if the g_frame_interval op is
not implemented at all, which is turned into -ENOTTY by video_usercopy.

[1] https://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/vidioc-subdev-g-frame-interval.html#return-value

> Maybe something like the following would be a better idea?
> 
>  utils/media-ctl/media-ctl.c | 10 +++++-----
>  1 file changed, 5 insertions(+), 5 deletions(-)
> 
> diff --git a/utils/media-ctl/media-ctl.c b/utils/media-ctl/media-ctl.c
> index f61963a..a50a559 100644
> --- a/utils/media-ctl/media-ctl.c
> +++ b/utils/media-ctl/media-ctl.c
> @@ -81,22 +81,22 @@ static void v4l2_subdev_print_format(struct media_entity *entity,
>  	struct v4l2_mbus_framefmt format;
>  	struct v4l2_fract interval = { 0, 0 };
>  	struct v4l2_rect rect;
> -	int ret;
> +	int ret, err_fi;
>  
>  	ret = v4l2_subdev_get_format(entity, &format, pad, which);
>  	if (ret != 0)
>  		return;
>  
> -	ret = v4l2_subdev_get_frame_interval(entity, &interval, pad);
> -	if (ret != 0 && ret != -ENOTTY)
> -		return;
> +	err_fi = v4l2_subdev_get_frame_interval(entity, &interval, pad);

Not supporting frame intervals doesn't warrant a visible error message,
I think -EINVAL should also be ignored above, if the spec is to be
believed.

>  
>  	printf("\t\t[fmt:%s/%ux%u",
>  	       v4l2_subdev_pixelcode_to_string(format.code),
>  	       format.width, format.height);
>  
> -	if (interval.numerator || interval.denominator)
> +	if (err_fi == 0 && (interval.numerator || interval.denominator))
>  		printf("@%u/%u", interval.numerator, interval.denominator);
> +	else if (err_fi != -ENOTTY)
> +		printf("@<error: %s>", strerror(-err_fi));

Or here.

>  
>  	if (format.field)
>  		printf(" field:%s", v4l2_subdev_field_to_string(format.field));
> 
> 

regards
Philipp


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 05:29:07PM +0100, Philipp Zabel wrote:
> According to the documentation [1], you are doing the right thing:
> 
>     The struct v4l2_subdev_frame_interval pad references a non-existing
>     pad, or the pad doesn’t support frame intervals.
> 
> But v4l2_subdev_call returns -ENOIOCTLCMD if the g_frame_interval op is
> not implemented at all, which is turned into -ENOTTY by video_usercopy.
> 
> [1] https://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/vidioc-subdev-g-frame-interval.html#return-value

Thanks for confirming.

> > Maybe something like the following would be a better idea?
> > 
> >  utils/media-ctl/media-ctl.c | 10 +++++-----
> >  1 file changed, 5 insertions(+), 5 deletions(-)
> > 
> > diff --git a/utils/media-ctl/media-ctl.c b/utils/media-ctl/media-ctl.c
> > index f61963a..a50a559 100644
> > --- a/utils/media-ctl/media-ctl.c
> > +++ b/utils/media-ctl/media-ctl.c
> > @@ -81,22 +81,22 @@ static void v4l2_subdev_print_format(struct media_entity *entity,
> >  	struct v4l2_mbus_framefmt format;
> >  	struct v4l2_fract interval = { 0, 0 };
> >  	struct v4l2_rect rect;
> > -	int ret;
> > +	int ret, err_fi;
> >  
> >  	ret = v4l2_subdev_get_format(entity, &format, pad, which);
> >  	if (ret != 0)
> >  		return;
> >  
> > -	ret = v4l2_subdev_get_frame_interval(entity, &interval, pad);
> > -	if (ret != 0 && ret != -ENOTTY)
> > -		return;
> > +	err_fi = v4l2_subdev_get_frame_interval(entity, &interval, pad);
> 
> Not supporting frame intervals doesn't warrant a visible error message,
> I think -EINVAL should also be ignored above, if the spec is to be
> believed.
> 
> >  
> >  	printf("\t\t[fmt:%s/%ux%u",
> >  	       v4l2_subdev_pixelcode_to_string(format.code),
> >  	       format.width, format.height);
> >  
> > -	if (interval.numerator || interval.denominator)
> > +	if (err_fi == 0 && (interval.numerator || interval.denominator))
> >  		printf("@%u/%u", interval.numerator, interval.denominator);
> > +	else if (err_fi != -ENOTTY)
> > +		printf("@<error: %s>", strerror(-err_fi));
> 
> Or here.

I don't mind which - I could change this to:

	else if (err_fi != -ENOTTY && err_fi != -EINVAL)

Or an alternative would be to print an error (ignoring ENOTTY and EINVAL)
to stderr at the "v4l2_subdev_get_frame_interval" callsite and continue
on (ensuring that interval is zeroed).

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 05:29:07PM +0100, Philipp Zabel wrote:
> According to the documentation [1], you are doing the right thing:
> 
>     The struct v4l2_subdev_frame_interval pad references a non-existing
>     pad, or the pad doesn?t support frame intervals.
> 
> But v4l2_subdev_call returns -ENOIOCTLCMD if the g_frame_interval op is
> not implemented at all, which is turned into -ENOTTY by video_usercopy.
> 
> [1] https://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/vidioc-subdev-g-frame-interval.html#return-value

Thanks for confirming.

> > Maybe something like the following would be a better idea?
> > 
> >  utils/media-ctl/media-ctl.c | 10 +++++-----
> >  1 file changed, 5 insertions(+), 5 deletions(-)
> > 
> > diff --git a/utils/media-ctl/media-ctl.c b/utils/media-ctl/media-ctl.c
> > index f61963a..a50a559 100644
> > --- a/utils/media-ctl/media-ctl.c
> > +++ b/utils/media-ctl/media-ctl.c
> > @@ -81,22 +81,22 @@ static void v4l2_subdev_print_format(struct media_entity *entity,
> >  	struct v4l2_mbus_framefmt format;
> >  	struct v4l2_fract interval = { 0, 0 };
> >  	struct v4l2_rect rect;
> > -	int ret;
> > +	int ret, err_fi;
> >  
> >  	ret = v4l2_subdev_get_format(entity, &format, pad, which);
> >  	if (ret != 0)
> >  		return;
> >  
> > -	ret = v4l2_subdev_get_frame_interval(entity, &interval, pad);
> > -	if (ret != 0 && ret != -ENOTTY)
> > -		return;
> > +	err_fi = v4l2_subdev_get_frame_interval(entity, &interval, pad);
> 
> Not supporting frame intervals doesn't warrant a visible error message,
> I think -EINVAL should also be ignored above, if the spec is to be
> believed.
> 
> >  
> >  	printf("\t\t[fmt:%s/%ux%u",
> >  	       v4l2_subdev_pixelcode_to_string(format.code),
> >  	       format.width, format.height);
> >  
> > -	if (interval.numerator || interval.denominator)
> > +	if (err_fi == 0 && (interval.numerator || interval.denominator))
> >  		printf("@%u/%u", interval.numerator, interval.denominator);
> > +	else if (err_fi != -ENOTTY)
> > +		printf("@<error: %s>", strerror(-err_fi));
> 
> Or here.

I don't mind which - I could change this to:

	else if (err_fi != -ENOTTY && err_fi != -EINVAL)

Or an alternative would be to print an error (ignoring ENOTTY and EINVAL)
to stderr at the "v4l2_subdev_get_frame_interval" callsite and continue
on (ensuring that interval is zeroed).

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Russell King - ARM Linux]

On Mon, Mar 20, 2017 at 05:29:07PM +0100, Philipp Zabel wrote:
> According to the documentation [1], you are doing the right thing:
> 
>     The struct v4l2_subdev_frame_interval pad references a non-existing
>     pad, or the pad doesn’t support frame intervals.
> 
> But v4l2_subdev_call returns -ENOIOCTLCMD if the g_frame_interval op is
> not implemented at all, which is turned into -ENOTTY by video_usercopy.
> 
> [1] https://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/vidioc-subdev-g-frame-interval.html#return-value

Thanks for confirming.

> > Maybe something like the following would be a better idea?
> > 
> >  utils/media-ctl/media-ctl.c | 10 +++++-----
> >  1 file changed, 5 insertions(+), 5 deletions(-)
> > 
> > diff --git a/utils/media-ctl/media-ctl.c b/utils/media-ctl/media-ctl.c
> > index f61963a..a50a559 100644
> > --- a/utils/media-ctl/media-ctl.c
> > +++ b/utils/media-ctl/media-ctl.c
> > @@ -81,22 +81,22 @@ static void v4l2_subdev_print_format(struct media_entity *entity,
> >  	struct v4l2_mbus_framefmt format;
> >  	struct v4l2_fract interval = { 0, 0 };
> >  	struct v4l2_rect rect;
> > -	int ret;
> > +	int ret, err_fi;
> >  
> >  	ret = v4l2_subdev_get_format(entity, &format, pad, which);
> >  	if (ret != 0)
> >  		return;
> >  
> > -	ret = v4l2_subdev_get_frame_interval(entity, &interval, pad);
> > -	if (ret != 0 && ret != -ENOTTY)
> > -		return;
> > +	err_fi = v4l2_subdev_get_frame_interval(entity, &interval, pad);
> 
> Not supporting frame intervals doesn't warrant a visible error message,
> I think -EINVAL should also be ignored above, if the spec is to be
> believed.
> 
> >  
> >  	printf("\t\t[fmt:%s/%ux%u",
> >  	       v4l2_subdev_pixelcode_to_string(format.code),
> >  	       format.width, format.height);
> >  
> > -	if (interval.numerator || interval.denominator)
> > +	if (err_fi == 0 && (interval.numerator || interval.denominator))
> >  		printf("@%u/%u", interval.numerator, interval.denominator);
> > +	else if (err_fi != -ENOTTY)
> > +		printf("@<error: %s>", strerror(-err_fi));
> 
> Or here.

I don't mind which - I could change this to:

	else if (err_fi != -ENOTTY && err_fi != -EINVAL)

Or an alternative would be to print an error (ignoring ENOTTY and EINVAL)
to stderr at the "v4l2_subdev_get_frame_interval" callsite and continue
on (ensuring that interval is zeroed).

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH v5 00/39] i.MX Media Driver

[Philipp Zabel]

On Sat, 2017-03-18 at 12:58 -0700, Steve Longerbeam wrote:
> 
> On 03/18/2017 12:22 PM, Russell King - ARM Linux wrote:
> > Hi Steve,
> >
> > I've just been trying to get gstreamer to capture and h264 encode
> > video from my camera at various frame rates, and what I've discovered
> > does not look good.
> >
> > 1) when setting frame rates, media-ctl _always_ calls
> >     VIDIOC_SUBDEV_S_FRAME_INTERVAL with pad=0.

To allow setting pad > 0:
https://patchwork.linuxtv.org/patch/39348/

> > 2) media-ctl never retrieves the frame interval information, so there's
> >     no way to read it back with standard tools, and no indication that
> >     this is going on...
> 
> I think Philipp Zabel submitted a patch which addresses these
> in media-ctl. Check with him.

To read back and propagate the frame interval:
https://patchwork.linuxtv.org/patch/39349/
https://patchwork.linuxtv.org/patch/39351/

regards
Philipp

[PATCH v5 00/39] i.MX Media Driver

[Philipp Zabel]

On Sat, 2017-03-18 at 12:58 -0700, Steve Longerbeam wrote:
> 
> On 03/18/2017 12:22 PM, Russell King - ARM Linux wrote:
> > Hi Steve,
> >
> > I've just been trying to get gstreamer to capture and h264 encode
> > video from my camera at various frame rates, and what I've discovered
> > does not look good.
> >
> > 1) when setting frame rates, media-ctl _always_ calls
> >     VIDIOC_SUBDEV_S_FRAME_INTERVAL with pad=0.

To allow setting pad > 0:
https://patchwork.linuxtv.org/patch/39348/

> > 2) media-ctl never retrieves the frame interval information, so there's
> >     no way to read it back with standard tools, and no indication that
> >     this is going on...
> 
> I think Philipp Zabel submitted a patch which addresses these
> in media-ctl. Check with him.

To read back and propagate the frame interval:
https://patchwork.linuxtv.org/patch/39349/
https://patchwork.linuxtv.org/patch/39351/

regards
Philipp

Re: [PATCH v5 00/39] i.MX Media Driver

[Philipp Zabel]

On Sat, 2017-03-18 at 12:58 -0700, Steve Longerbeam wrote:
> 
> On 03/18/2017 12:22 PM, Russell King - ARM Linux wrote:
> > Hi Steve,
> >
> > I've just been trying to get gstreamer to capture and h264 encode
> > video from my camera at various frame rates, and what I've discovered
> > does not look good.
> >
> > 1) when setting frame rates, media-ctl _always_ calls
> >     VIDIOC_SUBDEV_S_FRAME_INTERVAL with pad=0.

To allow setting pad > 0:
https://patchwork.linuxtv.org/patch/39348/

> > 2) media-ctl never retrieves the frame interval information, so there's
> >     no way to read it back with standard tools, and no indication that
> >     this is going on...
> 
> I think Philipp Zabel submitted a patch which addresses these
> in media-ctl. Check with him.

To read back and propagate the frame interval:
https://patchwork.linuxtv.org/patch/39349/
https://patchwork.linuxtv.org/patch/39351/

regards
Philipp

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html