* [PATCH V7 1/7] Documentation: devicetree: watchdog: da9062/61 watchdog timer binding
@ 2017-03-28 14:43 ` Steve Twiss
0 siblings, 0 replies; 36+ messages in thread
From: Steve Twiss @ 2017-03-28 14:43 UTC (permalink / raw)
To: DEVICETREE, Guenter Roeck, LINUX-KERNEL, LINUX-WATCHDOG,
Mark Rutland, Rob Herring, Wim Van Sebroeck
Cc: Dmitry Torokhov, Eduardo Valentin, LINUX-INPUT, LINUX-PM,
Lee Jones, Liam Girdwood, Mark Brown, Support Opensource,
Zhang Rui
From: Steve Twiss <stwiss.opensource@diasemi.com>
Add binding information for DA9062 and DA9061 watchdog.
Example bindings for both DA9062 and DA9061 devices are added. For
the DA9061 device, a fallback compatible line is added as a valid
combination of compatible strings.
The original binding for DA9062 (only) used to reside inside the
Documentation/devicetree/bindings/mfd/da9062.txt MFD document.
The da9062-watchdog section was deleted in that file and replaced
with a link to the new DA9061/62 binding information stored in this
patch.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
---
This patch applies against linux-next and v4.11-rc3
v6 -> v7
- NO CODE CHANGE
v5 -> v6
- NO CODE CHANGE
- Rebased from v4.9 to v4.11-rc3
v4 -> v5
- NO CODE CHANGE
- Rebased from v4.8 to v4.9
v3 -> v4
- NO CODE CHANGE
- Patch renamed from [PATCH V3 2/9] to [PATCH V4 1/8]
- Added Acked-by Rob Herring
v2 -> v3
- Patch renamed from [PATCH V1 02/10] to [PATCH V3 2/9]
- Each compatible line should be a valid combination of compatible
strings, alter DA9061 line to include the fall back compatible string
- Update the commit message to describe this change
- Add information about associated patches from this set without
describing them as being explicitly dependent on this binding
v1 -> v2
- Patch renamed from [PATCH V1 07/10] to [PATCH V2 02/10] -- these
changes were made to fix checkpatch warnings caused by the patch
set dependency order
- Updated the patch description to be explicit about where parts of
this binding had originally been stored
- A second example for DA9061 is provided to highlight the use of a
fall-back compatible option for the DA9062 watchdog driver
Hi,
No code changes for this version PATCH V5.
As previously:
For the watchdog case: the DA9062 device driver is compatible with the
DA9061 and for this reason there is minimal change required to the DA9062
watchdog device driver. The example for the DA9061 watchdog shows the
use of a fall-back compatible string.
Other information:
The device driver from this patch set (associated with this binding) is
[PATCH V5 6/8] watchdog: da9061: watchdog driver
Regards,
Steve Twiss, Dialog Semiconductor
.../devicetree/bindings/watchdog/da9062-wdt.txt | 23 ++++++++++++++++++++++
1 file changed, 23 insertions(+)
create mode 100644 Documentation/devicetree/bindings/watchdog/da9062-wdt.txt
diff --git a/Documentation/devicetree/bindings/watchdog/da9062-wdt.txt b/Documentation/devicetree/bindings/watchdog/da9062-wdt.txt
new file mode 100644
index 0000000..b935b52
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/da9062-wdt.txt
@@ -0,0 +1,23 @@
+* Dialog Semiconductor DA9062/61 Watchdog Timer
+
+Required properties:
+
+- compatible: should be one of the following valid compatible string lines:
+ "dlg,da9061-watchdog", "dlg,da9062-watchdog"
+ "dlg,da9062-watchdog"
+
+Example: DA9062
+
+ pmic0: da9062@58 {
+ watchdog {
+ compatible = "dlg,da9062-watchdog";
+ };
+ };
+
+Example: DA9061 using a fall-back compatible for the DA9062 watchdog driver
+
+ pmic0: da9061@58 {
+ watchdog {
+ compatible = "dlg,da9061-watchdog", "dlg,da9062-watchdog";
+ };
+ };
--
end-of-patch for PATCH V7
^ permalink raw reply related [flat|nested] 36+ messages in thread* [PATCH V7 1/7] Documentation: devicetree: watchdog: da9062/61 watchdog timer binding
@ 2017-03-28 14:43 ` Steve Twiss
0 siblings, 0 replies; 36+ messages in thread
From: Steve Twiss @ 2017-03-28 14:43 UTC (permalink / raw)
To: DEVICETREE, Guenter Roeck, LINUX-KERNEL, LINUX-WATCHDOG,
Mark Rutland, Rob Herring, Wim Van Sebroeck
Cc: Dmitry Torokhov, Eduardo Valentin, LINUX-INPUT, LINUX-PM,
Lee Jones, Liam Girdwood, Mark Brown, Support Opensource,
Zhang Rui
From: Steve Twiss <stwiss.opensource-WBD+wuPFNBhBDgjK7y7TUQ@public.gmane.org>
Add binding information for DA9062 and DA9061 watchdog.
Example bindings for both DA9062 and DA9061 devices are added. For
the DA9061 device, a fallback compatible line is added as a valid
combination of compatible strings.
The original binding for DA9062 (only) used to reside inside the
Documentation/devicetree/bindings/mfd/da9062.txt MFD document.
The da9062-watchdog section was deleted in that file and replaced
with a link to the new DA9061/62 binding information stored in this
patch.
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Signed-off-by: Steve Twiss <stwiss.opensource-WBD+wuPFNBhBDgjK7y7TUQ@public.gmane.org>
---
This patch applies against linux-next and v4.11-rc3
v6 -> v7
- NO CODE CHANGE
v5 -> v6
- NO CODE CHANGE
- Rebased from v4.9 to v4.11-rc3
v4 -> v5
- NO CODE CHANGE
- Rebased from v4.8 to v4.9
v3 -> v4
- NO CODE CHANGE
- Patch renamed from [PATCH V3 2/9] to [PATCH V4 1/8]
- Added Acked-by Rob Herring
v2 -> v3
- Patch renamed from [PATCH V1 02/10] to [PATCH V3 2/9]
- Each compatible line should be a valid combination of compatible
strings, alter DA9061 line to include the fall back compatible string
- Update the commit message to describe this change
- Add information about associated patches from this set without
describing them as being explicitly dependent on this binding
v1 -> v2
- Patch renamed from [PATCH V1 07/10] to [PATCH V2 02/10] -- these
changes were made to fix checkpatch warnings caused by the patch
set dependency order
- Updated the patch description to be explicit about where parts of
this binding had originally been stored
- A second example for DA9061 is provided to highlight the use of a
fall-back compatible option for the DA9062 watchdog driver
Hi,
No code changes for this version PATCH V5.
As previously:
For the watchdog case: the DA9062 device driver is compatible with the
DA9061 and for this reason there is minimal change required to the DA9062
watchdog device driver. The example for the DA9061 watchdog shows the
use of a fall-back compatible string.
Other information:
The device driver from this patch set (associated with this binding) is
[PATCH V5 6/8] watchdog: da9061: watchdog driver
Regards,
Steve Twiss, Dialog Semiconductor
.../devicetree/bindings/watchdog/da9062-wdt.txt | 23 ++++++++++++++++++++++
1 file changed, 23 insertions(+)
create mode 100644 Documentation/devicetree/bindings/watchdog/da9062-wdt.txt
diff --git a/Documentation/devicetree/bindings/watchdog/da9062-wdt.txt b/Documentation/devicetree/bindings/watchdog/da9062-wdt.txt
new file mode 100644
index 0000000..b935b52
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/da9062-wdt.txt
@@ -0,0 +1,23 @@
+* Dialog Semiconductor DA9062/61 Watchdog Timer
+
+Required properties:
+
+- compatible: should be one of the following valid compatible string lines:
+ "dlg,da9061-watchdog", "dlg,da9062-watchdog"
+ "dlg,da9062-watchdog"
+
+Example: DA9062
+
+ pmic0: da9062@58 {
+ watchdog {
+ compatible = "dlg,da9062-watchdog";
+ };
+ };
+
+Example: DA9061 using a fall-back compatible for the DA9062 watchdog driver
+
+ pmic0: da9061@58 {
+ watchdog {
+ compatible = "dlg,da9061-watchdog", "dlg,da9062-watchdog";
+ };
+ };
--
end-of-patch for PATCH V7
--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH V7 2/7] Documentation: devicetree: thermal: da9062/61 TJUNC temperature binding
2017-03-28 14:43 [PATCH V7 0/7] da9061: DA9061 driver submission Steve Twiss
2017-03-28 14:43 ` Steve Twiss
@ 2017-03-28 14:43 ` Steve Twiss
2017-03-28 14:43 ` Steve Twiss
` (5 subsequent siblings)
7 siblings, 0 replies; 36+ messages in thread
From: Steve Twiss @ 2017-03-28 14:43 UTC (permalink / raw)
To: DEVICETREE, Eduardo Valentin, LINUX-KERNEL, LINUX-PM,
Mark Rutland, Rob Herring, Zhang Rui
Cc: Dmitry Torokhov, Guenter Roeck, LINUX-INPUT, LINUX-WATCHDOG,
Lee Jones, Liam Girdwood, Lukasz Luba, Mark Brown,
Support Opensource, Wim Van Sebroeck
From: Steve Twiss <stwiss.opensource@diasemi.com>
Device tree binding information for DA9062 and DA9061 thermal junction
temperature monitor.
Binding descriptions for the DA9061 and DA9062 thermal TJUNC supervisor
device driver, using a single THERMAL_TRIP_HOT trip-wire and allowing for
a configurable polling period for over-temperature polling.
This patch also adds two examples, one for DA9062 and one for DA9061. The
DA9061 example uses a fall-back compatible string for the DA9062.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
---
This patch applies against linux-next and v4.11-rc3
v6 -> v7
- NO CODE CHANGE
v5 -> v6
- NO CODE CHANGE
- Rebased from v4.9 to v4.11-rc3
- Added Acked-by Rob Herring
v4 -> v5
- Rebased from v4.8 to v4.9
- Updates from comments by Eduardo Valentin
- Replace vendor defined dlg,tjunc-temp-polling-period-ms with standard
thermal core polling-delay-passive as part of the device tree
initialisation
- Remove Acked-by Rob Herring
v3 -> v4
- NO CODE CHANGE
- Patch renamed from [PATCH V3 3/9] to [PATCH V4 2/8]
- Added Acked-by Rob Herring
v2 -> v3
- Patch renamed from [PATCH V2 03/10] to [PATCH V3 3/9]
- Changes suggested from other component reviews by Rob Herring:
- Each compatible line should be a valid combination of compatible
strings: alter DA9061 line to include the fall back compatible string
and update the commit message accordingly
- Add e-mail information about associated patches from this set without
describing them as being explicitly dependent on this binding
v1 -> v2
- Patch renamed from [PATCH V1 08/10] to [PATCH V2 03/10] -- these
changes were made to fix checkpatch warnings caused by the patch
set dependency order
- A second example for DA9061 is provided to highlight the use of a
fall-back compatible option for the DA9062
Hi,
No code changes for this version PATCH V5.
As previously:
The device driver from this patch set (associated with this binding) is:
[PATCH V5 7/8] thermal: da9061: TJUNC temperature driver
Regards,
Steve Twiss, Dialog Semiconductor
.../devicetree/bindings/thermal/da9062-thermal.txt | 37 ++++++++++++++++++++++
1 file changed, 37 insertions(+)
create mode 100644 Documentation/devicetree/bindings/thermal/da9062-thermal.txt
diff --git a/Documentation/devicetree/bindings/thermal/da9062-thermal.txt b/Documentation/devicetree/bindings/thermal/da9062-thermal.txt
new file mode 100644
index 0000000..08cc72e
--- /dev/null
+++ b/Documentation/devicetree/bindings/thermal/da9062-thermal.txt
@@ -0,0 +1,37 @@
+* Dialog DA9062/61 TJUNC Thermal Module
+
+This module is part of the DA9061/DA9062. For more details about entire
+DA9062 and DA9061 chips see Documentation/devicetree/bindings/mfd/da9062.txt
+
+Junction temperature thermal module uses an interrupt signal to identify
+high THERMAL_TRIP_HOT temperatures for the PMIC device.
+
+Required properties:
+
+- compatible: should be one of the following valid compatible string lines:
+ "dlg,da9061-thermal", "dlg,da9062-thermal"
+ "dlg,da9062-thermal"
+
+Optional properties:
+
+- polling-delay-passive : Specify the polling period, measured in
+ milliseconds, between thermal zone device update checks.
+
+Example: DA9062
+
+ pmic0: da9062@58 {
+ thermal {
+ compatible = "dlg,da9062-thermal";
+ polling-delay-passive = <3000>;
+ };
+ };
+
+Example: DA9061 using a fall-back compatible for the DA9062 onkey driver
+
+ pmic0: da9061@58 {
+ thermal {
+ compatible = "dlg,da9061-thermal", "dlg,da9062-thermal";
+ polling-delay-passive = <3000>;
+ };
+ };
+
--
end-of-patch for PATCH V7
^ permalink raw reply related [flat|nested] 36+ messages in thread* [PATCH V7 3/7] Documentation: devicetree: mfd: da9062/61 MFD binding
2017-03-28 14:43 [PATCH V7 0/7] da9061: DA9061 driver submission Steve Twiss
@ 2017-03-28 14:43 ` Steve Twiss
2017-03-28 14:43 ` [PATCH V7 2/7] Documentation: devicetree: thermal: da9062/61 TJUNC temperature binding Steve Twiss
` (6 subsequent siblings)
7 siblings, 0 replies; 36+ messages in thread
From: Steve Twiss @ 2017-03-28 14:43 UTC (permalink / raw)
To: DEVICETREE, LINUX-INPUT, LINUX-KERNEL, Mark Rutland, Rob Herring
Cc: Dmitry Torokhov, Eduardo Valentin, Guenter Roeck, LINUX-INPUT,
LINUX-PM, LINUX-WATCHDOG, Lee Jones, Liam Girdwood, Mark Brown,
Support Opensource, Wim Van Sebroeck, Zhang Rui
From: Steve Twiss <stwiss.opensource@diasemi.com>
Extend existing DA9062 binding information to include the DA9061 PMIC for
MFD core and regulators.
Add a da9062-onkey link to the existing onkey binding file.
Add a da9062-thermal link to the new temperature monitoring binding file.
Delete the da9062-watchdog section and replace it with a link to the new
DA9061/62 binding information file.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
---
This patch applies against linux-next and v4.11-rc3
v6 -> v7
- NO CODE CHANGE
v5 -> v6
- NO CODE CHANGE
- Rebased from v4.9 to v4.11-rc3
v4 -> v5
- NO CODE CHANGE
- Rebased from v4.8 to v4.9
v3 -> v4
- Patch renamed from [PATCH V3 4/9] to [PATCH V4 3/8]
- Remove double newline spacing in text file
- Added Acked-by Rob Herring
v2 -> v3
- Patch renamed from [PATCH V2 04/10] to [PATCH V3 4/9]
- Ensure binding description concentrates on the device not the
device driver
- Separate the DA9061 and DA9062 sub-device tables to distinguish
the difference between the two devices
- Update the commit message to describe this change
- Add e-mail information about associated patches from this set
without describing them as being explicitly dependent on this
binding
v1 -> v2
- Patch renamed from [PATCH V1 09/10] to [PATCH V2 04/10] -- these
changes were made to fix checkpatch warnings caused by the patch
set dependency order
Hi,
Added an Ack from Rob Herring for the PATCH V3 version.
As previously:
Other information:
The device driver from this patch set (associated with this binding) is
- [PATCH V5 4/8] mfd: da9061: MFD core support
and also the following binding file changes:
- Binding for onkey (already applied by Dmitry Torokhov)
- [PATCH V5 1/8] Binding for watchdog
- [PATCH V5 2/8] Binding for thermal
Regards,
Steve Twiss, Dialog Semiconductor
Documentation/devicetree/bindings/mfd/da9062.txt | 49 +++++++++++++++++-------
1 file changed, 36 insertions(+), 13 deletions(-)
diff --git a/Documentation/devicetree/bindings/mfd/da9062.txt b/Documentation/devicetree/bindings/mfd/da9062.txt
index 38802b5..c0a418c 100644
--- a/Documentation/devicetree/bindings/mfd/da9062.txt
+++ b/Documentation/devicetree/bindings/mfd/da9062.txt
@@ -1,22 +1,39 @@
* Dialog DA9062 Power Management Integrated Circuit (PMIC)
-DA9062 consists of a large and varied group of sub-devices:
+Product information for the DA9062 and DA9061 devices can be found here:
+- http://www.dialog-semiconductor.com/products/da9062
+- http://www.dialog-semiconductor.com/products/da9061
+
+The DA9062 PMIC consists of:
Device Supply Names Description
------ ------------ -----------
da9062-regulator : : LDOs & BUCKs
da9062-rtc : : Real-Time Clock
+da9062-onkey : : On Key
+da9062-watchdog : : Watchdog Timer
+da9062-thermal : : Thermal
+
+The DA9061 PMIC consists of:
+
+Device Supply Names Description
+------ ------------ -----------
+da9062-regulator : : LDOs & BUCKs
+da9062-onkey : : On Key
da9062-watchdog : : Watchdog Timer
+da9062-thermal : : Thermal
======
Required properties:
-- compatible : Should be "dlg,da9062".
+- compatible : Should be
+ "dlg,da9062" for DA9062
+ "dlg,da9061" for DA9061
- reg : Specifies the I2C slave address (this defaults to 0x58 but it can be
modified to match the chip's OTP settings).
- interrupt-parent : Specifies the reference to the interrupt controller for
- the DA9062.
+ the DA9062 or DA9061.
- interrupts : IRQ line information.
- interrupt-controller
@@ -25,8 +42,8 @@ further information on IRQ bindings.
Sub-nodes:
-- regulators : This node defines the settings for the LDOs and BUCKs. The
- DA9062 regulators are bound using their names listed below:
+- regulators : This node defines the settings for the LDOs and BUCKs.
+ The DA9062 regulators are bound using their names listed below:
buck1 : BUCK_1
buck2 : BUCK_2
@@ -37,19 +54,29 @@ Sub-nodes:
ldo3 : LDO_3
ldo4 : LDO_4
+ The DA9061 regulators are bound using their names listed below:
+
+ buck1 : BUCK_1
+ buck2 : BUCK_2
+ buck3 : BUCK_3
+ ldo1 : LDO_1
+ ldo2 : LDO_2
+ ldo3 : LDO_3
+ ldo4 : LDO_4
+
The component follows the standard regulator framework and the bindings
details of individual regulator device can be found in:
Documentation/devicetree/bindings/regulator/regulator.txt
-
- rtc : This node defines settings required for the Real-Time Clock associated
with the DA9062. There are currently no entries in this binding, however
compatible = "dlg,da9062-rtc" should be added if a node is created.
-- watchdog: This node defines the settings for the watchdog driver associated
- with the DA9062 PMIC. The compatible = "dlg,da9062-watchdog" should be added
- if a node is created.
+- onkey : See ../input/da9062-onkey.txt
+
+- watchdog: See ../watchdog/da9062-watchdog.txt
+- thermal : See ../thermal/da9062-thermal.txt
Example:
@@ -64,10 +91,6 @@ Example:
compatible = "dlg,da9062-rtc";
};
- watchdog {
- compatible = "dlg,da9062-watchdog";
- };
-
regulators {
DA9062_BUCK1: buck1 {
regulator-name = "BUCK1";
--
end-of-patch for PATCH V7
^ permalink raw reply related [flat|nested] 36+ messages in thread* [PATCH V7 3/7] Documentation: devicetree: mfd: da9062/61 MFD binding
@ 2017-03-28 14:43 ` Steve Twiss
0 siblings, 0 replies; 36+ messages in thread
From: Steve Twiss @ 2017-03-28 14:43 UTC (permalink / raw)
To: DEVICETREE, LINUX-KERNEL, Mark Rutland, Rob Herring
Cc: Dmitry Torokhov, Eduardo Valentin, Guenter Roeck, LINUX-INPUT,
LINUX-PM, LINUX-WATCHDOG, Lee Jones, Liam Girdwood, Mark Brown,
Support Opensource, Wim Van Sebroeck, Zhang Rui
From: Steve Twiss <stwiss.opensource@diasemi.com>
Extend existing DA9062 binding information to include the DA9061 PMIC for
MFD core and regulators.
Add a da9062-onkey link to the existing onkey binding file.
Add a da9062-thermal link to the new temperature monitoring binding file.
Delete the da9062-watchdog section and replace it with a link to the new
DA9061/62 binding information file.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
---
This patch applies against linux-next and v4.11-rc3
v6 -> v7
- NO CODE CHANGE
v5 -> v6
- NO CODE CHANGE
- Rebased from v4.9 to v4.11-rc3
v4 -> v5
- NO CODE CHANGE
- Rebased from v4.8 to v4.9
v3 -> v4
- Patch renamed from [PATCH V3 4/9] to [PATCH V4 3/8]
- Remove double newline spacing in text file
- Added Acked-by Rob Herring
v2 -> v3
- Patch renamed from [PATCH V2 04/10] to [PATCH V3 4/9]
- Ensure binding description concentrates on the device not the
device driver
- Separate the DA9061 and DA9062 sub-device tables to distinguish
the difference between the two devices
- Update the commit message to describe this change
- Add e-mail information about associated patches from this set
without describing them as being explicitly dependent on this
binding
v1 -> v2
- Patch renamed from [PATCH V1 09/10] to [PATCH V2 04/10] -- these
changes were made to fix checkpatch warnings caused by the patch
set dependency order
Hi,
Added an Ack from Rob Herring for the PATCH V3 version.
As previously:
Other information:
The device driver from this patch set (associated with this binding) is
- [PATCH V5 4/8] mfd: da9061: MFD core support
and also the following binding file changes:
- Binding for onkey (already applied by Dmitry Torokhov)
- [PATCH V5 1/8] Binding for watchdog
- [PATCH V5 2/8] Binding for thermal
Regards,
Steve Twiss, Dialog Semiconductor
Documentation/devicetree/bindings/mfd/da9062.txt | 49 +++++++++++++++++-------
1 file changed, 36 insertions(+), 13 deletions(-)
diff --git a/Documentation/devicetree/bindings/mfd/da9062.txt b/Documentation/devicetree/bindings/mfd/da9062.txt
index 38802b5..c0a418c 100644
--- a/Documentation/devicetree/bindings/mfd/da9062.txt
+++ b/Documentation/devicetree/bindings/mfd/da9062.txt
@@ -1,22 +1,39 @@
* Dialog DA9062 Power Management Integrated Circuit (PMIC)
-DA9062 consists of a large and varied group of sub-devices:
+Product information for the DA9062 and DA9061 devices can be found here:
+- http://www.dialog-semiconductor.com/products/da9062
+- http://www.dialog-semiconductor.com/products/da9061
+
+The DA9062 PMIC consists of:
Device Supply Names Description
------ ------------ -----------
da9062-regulator : : LDOs & BUCKs
da9062-rtc : : Real-Time Clock
+da9062-onkey : : On Key
+da9062-watchdog : : Watchdog Timer
+da9062-thermal : : Thermal
+
+The DA9061 PMIC consists of:
+
+Device Supply Names Description
+------ ------------ -----------
+da9062-regulator : : LDOs & BUCKs
+da9062-onkey : : On Key
da9062-watchdog : : Watchdog Timer
+da9062-thermal : : Thermal
======
Required properties:
-- compatible : Should be "dlg,da9062".
+- compatible : Should be
+ "dlg,da9062" for DA9062
+ "dlg,da9061" for DA9061
- reg : Specifies the I2C slave address (this defaults to 0x58 but it can be
modified to match the chip's OTP settings).
- interrupt-parent : Specifies the reference to the interrupt controller for
- the DA9062.
+ the DA9062 or DA9061.
- interrupts : IRQ line information.
- interrupt-controller
@@ -25,8 +42,8 @@ further information on IRQ bindings.
Sub-nodes:
-- regulators : This node defines the settings for the LDOs and BUCKs. The
- DA9062 regulators are bound using their names listed below:
+- regulators : This node defines the settings for the LDOs and BUCKs.
+ The DA9062 regulators are bound using their names listed below:
buck1 : BUCK_1
buck2 : BUCK_2
@@ -37,19 +54,29 @@ Sub-nodes:
ldo3 : LDO_3
ldo4 : LDO_4
+ The DA9061 regulators are bound using their names listed below:
+
+ buck1 : BUCK_1
+ buck2 : BUCK_2
+ buck3 : BUCK_3
+ ldo1 : LDO_1
+ ldo2 : LDO_2
+ ldo3 : LDO_3
+ ldo4 : LDO_4
+
The component follows the standard regulator framework and the bindings
details of individual regulator device can be found in:
Documentation/devicetree/bindings/regulator/regulator.txt
-
- rtc : This node defines settings required for the Real-Time Clock associated
with the DA9062. There are currently no entries in this binding, however
compatible = "dlg,da9062-rtc" should be added if a node is created.
-- watchdog: This node defines the settings for the watchdog driver associated
- with the DA9062 PMIC. The compatible = "dlg,da9062-watchdog" should be added
- if a node is created.
+- onkey : See ../input/da9062-onkey.txt
+
+- watchdog: See ../watchdog/da9062-watchdog.txt
+- thermal : See ../thermal/da9062-thermal.txt
Example:
@@ -64,10 +91,6 @@ Example:
compatible = "dlg,da9062-rtc";
};
- watchdog {
- compatible = "dlg,da9062-watchdog";
- };
-
regulators {
DA9062_BUCK1: buck1 {
regulator-name = "BUCK1";
--
end-of-patch for PATCH V7
^ permalink raw reply related [flat|nested] 36+ messages in thread* Re: [PATCH V7 3/7] Documentation: devicetree: mfd: da9062/61 MFD binding
2017-03-28 14:43 ` Steve Twiss
@ 2017-04-03 13:39 ` Lee Jones
-1 siblings, 0 replies; 36+ messages in thread
From: Lee Jones @ 2017-04-03 13:39 UTC (permalink / raw)
To: Steve Twiss
Cc: DEVICETREE, LINUX-INPUT, LINUX-KERNEL, Mark Rutland, Rob Herring,
Dmitry Torokhov, Eduardo Valentin, Guenter Roeck, LINUX-PM,
LINUX-WATCHDOG, Liam Girdwood, Mark Brown, Support Opensource,
Wim Van Sebroeck, Zhang Rui
On Tue, 28 Mar 2017, Steve Twiss wrote:
> From: Steve Twiss <stwiss.opensource@diasemi.com>
>
> Extend existing DA9062 binding information to include the DA9061 PMIC for
> MFD core and regulators.
>
> Add a da9062-onkey link to the existing onkey binding file.
>
> Add a da9062-thermal link to the new temperature monitoring binding file.
>
> Delete the da9062-watchdog section and replace it with a link to the new
> DA9061/62 binding information file.
>
> Acked-by: Rob Herring <robh@kernel.org>
> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
>
> ---
> This patch applies against linux-next and v4.11-rc3
>
> v6 -> v7
> - NO CODE CHANGE
>
> v5 -> v6
> - NO CODE CHANGE
> - Rebased from v4.9 to v4.11-rc3
>
> v4 -> v5
> - NO CODE CHANGE
> - Rebased from v4.8 to v4.9
>
> v3 -> v4
> - Patch renamed from [PATCH V3 4/9] to [PATCH V4 3/8]
> - Remove double newline spacing in text file
> - Added Acked-by Rob Herring
>
> v2 -> v3
> - Patch renamed from [PATCH V2 04/10] to [PATCH V3 4/9]
> - Ensure binding description concentrates on the device not the
> device driver
> - Separate the DA9061 and DA9062 sub-device tables to distinguish
> the difference between the two devices
> - Update the commit message to describe this change
> - Add e-mail information about associated patches from this set
> without describing them as being explicitly dependent on this
> binding
>
> v1 -> v2
> - Patch renamed from [PATCH V1 09/10] to [PATCH V2 04/10] -- these
> changes were made to fix checkpatch warnings caused by the patch
> set dependency order
>
> Hi,
>
> Added an Ack from Rob Herring for the PATCH V3 version.
>
> As previously:
> Other information:
> The device driver from this patch set (associated with this binding) is
>
> - [PATCH V5 4/8] mfd: da9061: MFD core support
>
> and also the following binding file changes:
>
> - Binding for onkey (already applied by Dmitry Torokhov)
> - [PATCH V5 1/8] Binding for watchdog
> - [PATCH V5 2/8] Binding for thermal
>
> Regards,
> Steve Twiss, Dialog Semiconductor
>
>
> Documentation/devicetree/bindings/mfd/da9062.txt | 49 +++++++++++++++++-------
> 1 file changed, 36 insertions(+), 13 deletions(-)
Applied, thanks.
> diff --git a/Documentation/devicetree/bindings/mfd/da9062.txt b/Documentation/devicetree/bindings/mfd/da9062.txt
> index 38802b5..c0a418c 100644
> --- a/Documentation/devicetree/bindings/mfd/da9062.txt
> +++ b/Documentation/devicetree/bindings/mfd/da9062.txt
> @@ -1,22 +1,39 @@
> * Dialog DA9062 Power Management Integrated Circuit (PMIC)
>
> -DA9062 consists of a large and varied group of sub-devices:
> +Product information for the DA9062 and DA9061 devices can be found here:
> +- http://www.dialog-semiconductor.com/products/da9062
> +- http://www.dialog-semiconductor.com/products/da9061
> +
> +The DA9062 PMIC consists of:
>
> Device Supply Names Description
> ------ ------------ -----------
> da9062-regulator : : LDOs & BUCKs
> da9062-rtc : : Real-Time Clock
> +da9062-onkey : : On Key
> +da9062-watchdog : : Watchdog Timer
> +da9062-thermal : : Thermal
> +
> +The DA9061 PMIC consists of:
> +
> +Device Supply Names Description
> +------ ------------ -----------
> +da9062-regulator : : LDOs & BUCKs
> +da9062-onkey : : On Key
> da9062-watchdog : : Watchdog Timer
> +da9062-thermal : : Thermal
>
> ======
>
> Required properties:
>
> -- compatible : Should be "dlg,da9062".
> +- compatible : Should be
> + "dlg,da9062" for DA9062
> + "dlg,da9061" for DA9061
> - reg : Specifies the I2C slave address (this defaults to 0x58 but it can be
> modified to match the chip's OTP settings).
> - interrupt-parent : Specifies the reference to the interrupt controller for
> - the DA9062.
> + the DA9062 or DA9061.
> - interrupts : IRQ line information.
> - interrupt-controller
>
> @@ -25,8 +42,8 @@ further information on IRQ bindings.
>
> Sub-nodes:
>
> -- regulators : This node defines the settings for the LDOs and BUCKs. The
> - DA9062 regulators are bound using their names listed below:
> +- regulators : This node defines the settings for the LDOs and BUCKs.
> + The DA9062 regulators are bound using their names listed below:
>
> buck1 : BUCK_1
> buck2 : BUCK_2
> @@ -37,19 +54,29 @@ Sub-nodes:
> ldo3 : LDO_3
> ldo4 : LDO_4
>
> + The DA9061 regulators are bound using their names listed below:
> +
> + buck1 : BUCK_1
> + buck2 : BUCK_2
> + buck3 : BUCK_3
> + ldo1 : LDO_1
> + ldo2 : LDO_2
> + ldo3 : LDO_3
> + ldo4 : LDO_4
> +
> The component follows the standard regulator framework and the bindings
> details of individual regulator device can be found in:
> Documentation/devicetree/bindings/regulator/regulator.txt
>
> -
> - rtc : This node defines settings required for the Real-Time Clock associated
> with the DA9062. There are currently no entries in this binding, however
> compatible = "dlg,da9062-rtc" should be added if a node is created.
>
> -- watchdog: This node defines the settings for the watchdog driver associated
> - with the DA9062 PMIC. The compatible = "dlg,da9062-watchdog" should be added
> - if a node is created.
> +- onkey : See ../input/da9062-onkey.txt
> +
> +- watchdog: See ../watchdog/da9062-watchdog.txt
>
> +- thermal : See ../thermal/da9062-thermal.txt
>
> Example:
>
> @@ -64,10 +91,6 @@ Example:
> compatible = "dlg,da9062-rtc";
> };
>
> - watchdog {
> - compatible = "dlg,da9062-watchdog";
> - };
> -
> regulators {
> DA9062_BUCK1: buck1 {
> regulator-name = "BUCK1";
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 36+ messages in thread* Re: [PATCH V7 3/7] Documentation: devicetree: mfd: da9062/61 MFD binding
@ 2017-04-03 13:39 ` Lee Jones
0 siblings, 0 replies; 36+ messages in thread
From: Lee Jones @ 2017-04-03 13:39 UTC (permalink / raw)
To: Steve Twiss
Cc: DEVICETREE, LINUX-INPUT, LINUX-KERNEL, Mark Rutland, Rob Herring,
Dmitry Torokhov, Eduardo Valentin, Guenter Roeck, LINUX-PM,
LINUX-WATCHDOG, Liam Girdwood, Mark Brown, Support Opensource,
Wim Van Sebroeck, Zhang Rui
On Tue, 28 Mar 2017, Steve Twiss wrote:
> From: Steve Twiss <stwiss.opensource@diasemi.com>
>
> Extend existing DA9062 binding information to include the DA9061 PMIC for
> MFD core and regulators.
>
> Add a da9062-onkey link to the existing onkey binding file.
>
> Add a da9062-thermal link to the new temperature monitoring binding file.
>
> Delete the da9062-watchdog section and replace it with a link to the new
> DA9061/62 binding information file.
>
> Acked-by: Rob Herring <robh@kernel.org>
> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
>
> ---
> This patch applies against linux-next and v4.11-rc3
>
> v6 -> v7
> - NO CODE CHANGE
>
> v5 -> v6
> - NO CODE CHANGE
> - Rebased from v4.9 to v4.11-rc3
>
> v4 -> v5
> - NO CODE CHANGE
> - Rebased from v4.8 to v4.9
>
> v3 -> v4
> - Patch renamed from [PATCH V3 4/9] to [PATCH V4 3/8]
> - Remove double newline spacing in text file
> - Added Acked-by Rob Herring
>
> v2 -> v3
> - Patch renamed from [PATCH V2 04/10] to [PATCH V3 4/9]
> - Ensure binding description concentrates on the device not the
> device driver
> - Separate the DA9061 and DA9062 sub-device tables to distinguish
> the difference between the two devices
> - Update the commit message to describe this change
> - Add e-mail information about associated patches from this set
> without describing them as being explicitly dependent on this
> binding
>
> v1 -> v2
> - Patch renamed from [PATCH V1 09/10] to [PATCH V2 04/10] -- these
> changes were made to fix checkpatch warnings caused by the patch
> set dependency order
>
> Hi,
>
> Added an Ack from Rob Herring for the PATCH V3 version.
>
> As previously:
> Other information:
> The device driver from this patch set (associated with this binding) is
>
> - [PATCH V5 4/8] mfd: da9061: MFD core support
>
> and also the following binding file changes:
>
> - Binding for onkey (already applied by Dmitry Torokhov)
> - [PATCH V5 1/8] Binding for watchdog
> - [PATCH V5 2/8] Binding for thermal
>
> Regards,
> Steve Twiss, Dialog Semiconductor
>
>
> Documentation/devicetree/bindings/mfd/da9062.txt | 49 +++++++++++++++++-------
> 1 file changed, 36 insertions(+), 13 deletions(-)
Applied, thanks.
> diff --git a/Documentation/devicetree/bindings/mfd/da9062.txt b/Documentation/devicetree/bindings/mfd/da9062.txt
> index 38802b5..c0a418c 100644
> --- a/Documentation/devicetree/bindings/mfd/da9062.txt
> +++ b/Documentation/devicetree/bindings/mfd/da9062.txt
> @@ -1,22 +1,39 @@
> * Dialog DA9062 Power Management Integrated Circuit (PMIC)
>
> -DA9062 consists of a large and varied group of sub-devices:
> +Product information for the DA9062 and DA9061 devices can be found here:
> +- http://www.dialog-semiconductor.com/products/da9062
> +- http://www.dialog-semiconductor.com/products/da9061
> +
> +The DA9062 PMIC consists of:
>
> Device Supply Names Description
> ------ ------------ -----------
> da9062-regulator : : LDOs & BUCKs
> da9062-rtc : : Real-Time Clock
> +da9062-onkey : : On Key
> +da9062-watchdog : : Watchdog Timer
> +da9062-thermal : : Thermal
> +
> +The DA9061 PMIC consists of:
> +
> +Device Supply Names Description
> +------ ------------ -----------
> +da9062-regulator : : LDOs & BUCKs
> +da9062-onkey : : On Key
> da9062-watchdog : : Watchdog Timer
> +da9062-thermal : : Thermal
>
> ======
>
> Required properties:
>
> -- compatible : Should be "dlg,da9062".
> +- compatible : Should be
> + "dlg,da9062" for DA9062
> + "dlg,da9061" for DA9061
> - reg : Specifies the I2C slave address (this defaults to 0x58 but it can be
> modified to match the chip's OTP settings).
> - interrupt-parent : Specifies the reference to the interrupt controller for
> - the DA9062.
> + the DA9062 or DA9061.
> - interrupts : IRQ line information.
> - interrupt-controller
>
> @@ -25,8 +42,8 @@ further information on IRQ bindings.
>
> Sub-nodes:
>
> -- regulators : This node defines the settings for the LDOs and BUCKs. The
> - DA9062 regulators are bound using their names listed below:
> +- regulators : This node defines the settings for the LDOs and BUCKs.
> + The DA9062 regulators are bound using their names listed below:
>
> buck1 : BUCK_1
> buck2 : BUCK_2
> @@ -37,19 +54,29 @@ Sub-nodes:
> ldo3 : LDO_3
> ldo4 : LDO_4
>
> + The DA9061 regulators are bound using their names listed below:
> +
> + buck1 : BUCK_1
> + buck2 : BUCK_2
> + buck3 : BUCK_3
> + ldo1 : LDO_1
> + ldo2 : LDO_2
> + ldo3 : LDO_3
> + ldo4 : LDO_4
> +
> The component follows the standard regulator framework and the bindings
> details of individual regulator device can be found in:
> Documentation/devicetree/bindings/regulator/regulator.txt
>
> -
> - rtc : This node defines settings required for the Real-Time Clock associated
> with the DA9062. There are currently no entries in this binding, however
> compatible = "dlg,da9062-rtc" should be added if a node is created.
>
> -- watchdog: This node defines the settings for the watchdog driver associated
> - with the DA9062 PMIC. The compatible = "dlg,da9062-watchdog" should be added
> - if a node is created.
> +- onkey : See ../input/da9062-onkey.txt
> +
> +- watchdog: See ../watchdog/da9062-watchdog.txt
>
> +- thermal : See ../thermal/da9062-thermal.txt
>
> Example:
>
> @@ -64,10 +91,6 @@ Example:
> compatible = "dlg,da9062-rtc";
> };
>
> - watchdog {
> - compatible = "dlg,da9062-watchdog";
> - };
> -
> regulators {
> DA9062_BUCK1: buck1 {
> regulator-name = "BUCK1";
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH V7 4/7] mfd: da9061: MFD core support
@ 2017-03-28 14:43 ` Steve Twiss
0 siblings, 0 replies; 36+ messages in thread
From: Steve Twiss @ 2017-03-28 14:43 UTC (permalink / raw)
To: LINUX-KERNEL, Lee Jones
Cc: DEVICETREE, Dmitry Torokhov, Eduardo Valentin, Guenter Roeck,
LINUX-INPUT, LINUX-PM, LINUX-WATCHDOG, Liam Girdwood, Mark Brown,
Mark Rutland, Rob Herring, Support Opensource, Wim Van Sebroeck,
Zhang Rui
From: Steve Twiss <stwiss.opensource@diasemi.com>
MFD support for DA9061 is provided as part of the DA9062 device driver.
The registers header file adds two new chip variant IDs defined in DA9061
and DA9062 hardware. The core header file adds new software enumerations
for listing the valid DA9061 IRQs and a da9062_compatible_types enumeration
for distinguishing between DA9061/62 devices in software.
The core source code adds a new .compatible of_device_id entry. This is
extended from DA9062 to support both "dlg,da9061" and "dlg,da9062". The
.data entry now holds a reference to the enumerated device type.
A new regmap_irq_chip model is added for DA9061 and this supports the new
list of regmap_irq entries. A new mfd_cell da9061_devs[] array lists the
new sub system components for DA9061. Support is added for a new DA9061
regmap_config which lists the correct readable, writable and volatile
ranges for this chip.
The probe function uses the device tree compatible string to switch on the
da9062_compatible_types and configure the correct mfd cells, irq chip and
regmap config.
Kconfig is updated to reflect support for DA9061 and DA9062 PMICs.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
---
Acked-for-mfd-by: Lee Jones <lee.jones@linaro.org>
Hi Lee, that Ack was from your earlier posting:
https://lkml.org/lkml/2017/1/4/328 this was
Regards, Steve.
This patch applies against linux-next and v4.11-rc3
v6 -> v7
- Remove compilation warning when casting a void * to an integer on
ARCH=x86_64 using -Wpointer-to-int-cast.
- Recommendation uintptr_t cast: https://lkml.org/lkml/2017/3/28/292
- Compile tested ARCH=x86_64
v5 -> v6
- Rebased from v4.9 to v4.11-rc3
- Modify Copyright to match Dialog latest legal statement
- Fixed "braces {} should be used on all arms" checkpatch warning
v4 -> v5
- NO CODE CHANGE
- Rebased from v4.8 to v4.9
v3 -> v4
- Patch renamed from [PATCH V3 5/9] to [PATCH V4 4/8]
- Removed DEFINE_RES_NAMED() macros for DA9061 resources and replaced
them with DEFINE_RES_IRQ_NAMED().
- Removed whitespace
- Reverted change for badly defined mfd_cell da9062_devs of_compatible
string from "dlg,da9062-watchdog" back to "dlg,da9062-wdt"
v2 -> v3
- NO CODE CHANGE
- Patch renamed from [PATCH V2 05/10] to [PATCH V3 5/9]
v1 -> v2
- Patch renamed from [PATCH V1 01/10] to [PATCH V2 05/10] -- these
changes were made to fix checkpatch warnings caused by the patch
set dependency order
- Fixed typo in the commit message "readble" to "readable"
- Removed the explicit cross-check to decide if there is a conflict
between the device tree compatible string and the hardware definition.
This patch assumes the device tree is correctly written and therefore
removes the need for a hardware/DT sanity check.
- Removed extra semicolon in drivers/mfd/da9062-core.c:877
- Re-write compatible entries into numerical order
Lee,
Changes as described in the version history above.
As previously:
This patch adds support for the DA9061 PMIC. This is done as part of the
existing DA9062 device driver by extending the of_device_id match table.
This in turn allows new MFD cells, irq chip and regmap definitions to
support DA9061.
Regards,
Steve Twiss, Dialog Semiconductor
drivers/mfd/Kconfig | 5 +-
drivers/mfd/da9062-core.c | 427 +++++++++++++++++++++++++++++++++--
include/linux/mfd/da9062/core.h | 29 ++-
include/linux/mfd/da9062/registers.h | 5 +-
4 files changed, 443 insertions(+), 23 deletions(-)
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 55ecdfb..29cc11a 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -263,13 +263,14 @@ config MFD_DA9055
called "da9055"
config MFD_DA9062
- tristate "Dialog Semiconductor DA9062 PMIC Support"
+ tristate "Dialog Semiconductor DA9062/61 PMIC Support"
select MFD_CORE
select REGMAP_I2C
select REGMAP_IRQ
depends on I2C
help
- Say yes here for support for the Dialog Semiconductor DA9062 PMIC.
+ Say yes here for support for the Dialog Semiconductor DA9061 and
+ DA9062 PMICs.
This includes the I2C driver and core APIs.
Additional drivers must be enabled in order to use the functionality
of the device.
diff --git a/drivers/mfd/da9062-core.c b/drivers/mfd/da9062-core.c
index 8f873866..78ab3f4 100644
--- a/drivers/mfd/da9062-core.c
+++ b/drivers/mfd/da9062-core.c
@@ -1,6 +1,6 @@
/*
- * Core, IRQ and I2C device driver for DA9062 PMIC
- * Copyright (C) 2015 Dialog Semiconductor Ltd.
+ * Core, IRQ and I2C device driver for DA9061 and DA9062 PMICs
+ * Copyright (C) 2015-2017 Dialog Semiconductor
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
@@ -30,6 +30,70 @@
#define DA9062_REG_EVENT_B_OFFSET 1
#define DA9062_REG_EVENT_C_OFFSET 2
+static struct regmap_irq da9061_irqs[] = {
+ /* EVENT A */
+ [DA9061_IRQ_ONKEY] = {
+ .reg_offset = DA9062_REG_EVENT_A_OFFSET,
+ .mask = DA9062AA_M_NONKEY_MASK,
+ },
+ [DA9061_IRQ_WDG_WARN] = {
+ .reg_offset = DA9062_REG_EVENT_A_OFFSET,
+ .mask = DA9062AA_M_WDG_WARN_MASK,
+ },
+ [DA9061_IRQ_SEQ_RDY] = {
+ .reg_offset = DA9062_REG_EVENT_A_OFFSET,
+ .mask = DA9062AA_M_SEQ_RDY_MASK,
+ },
+ /* EVENT B */
+ [DA9061_IRQ_TEMP] = {
+ .reg_offset = DA9062_REG_EVENT_B_OFFSET,
+ .mask = DA9062AA_M_TEMP_MASK,
+ },
+ [DA9061_IRQ_LDO_LIM] = {
+ .reg_offset = DA9062_REG_EVENT_B_OFFSET,
+ .mask = DA9062AA_M_LDO_LIM_MASK,
+ },
+ [DA9061_IRQ_DVC_RDY] = {
+ .reg_offset = DA9062_REG_EVENT_B_OFFSET,
+ .mask = DA9062AA_M_DVC_RDY_MASK,
+ },
+ [DA9061_IRQ_VDD_WARN] = {
+ .reg_offset = DA9062_REG_EVENT_B_OFFSET,
+ .mask = DA9062AA_M_VDD_WARN_MASK,
+ },
+ /* EVENT C */
+ [DA9061_IRQ_GPI0] = {
+ .reg_offset = DA9062_REG_EVENT_C_OFFSET,
+ .mask = DA9062AA_M_GPI0_MASK,
+ },
+ [DA9061_IRQ_GPI1] = {
+ .reg_offset = DA9062_REG_EVENT_C_OFFSET,
+ .mask = DA9062AA_M_GPI1_MASK,
+ },
+ [DA9061_IRQ_GPI2] = {
+ .reg_offset = DA9062_REG_EVENT_C_OFFSET,
+ .mask = DA9062AA_M_GPI2_MASK,
+ },
+ [DA9061_IRQ_GPI3] = {
+ .reg_offset = DA9062_REG_EVENT_C_OFFSET,
+ .mask = DA9062AA_M_GPI3_MASK,
+ },
+ [DA9061_IRQ_GPI4] = {
+ .reg_offset = DA9062_REG_EVENT_C_OFFSET,
+ .mask = DA9062AA_M_GPI4_MASK,
+ },
+};
+
+static struct regmap_irq_chip da9061_irq_chip = {
+ .name = "da9061-irq",
+ .irqs = da9061_irqs,
+ .num_irqs = DA9061_NUM_IRQ,
+ .num_regs = 3,
+ .status_base = DA9062AA_EVENT_A,
+ .mask_base = DA9062AA_IRQ_MASK_A,
+ .ack_base = DA9062AA_EVENT_A,
+};
+
static struct regmap_irq da9062_irqs[] = {
/* EVENT A */
[DA9062_IRQ_ONKEY] = {
@@ -102,6 +166,57 @@
.ack_base = DA9062AA_EVENT_A,
};
+static struct resource da9061_core_resources[] = {
+ DEFINE_RES_IRQ_NAMED(DA9061_IRQ_VDD_WARN, "VDD_WARN"),
+};
+
+static struct resource da9061_regulators_resources[] = {
+ DEFINE_RES_IRQ_NAMED(DA9061_IRQ_LDO_LIM, "LDO_LIM"),
+};
+
+static struct resource da9061_thermal_resources[] = {
+ DEFINE_RES_IRQ_NAMED(DA9061_IRQ_TEMP, "THERMAL"),
+};
+
+static struct resource da9061_wdt_resources[] = {
+ DEFINE_RES_IRQ_NAMED(DA9061_IRQ_WDG_WARN, "WD_WARN"),
+};
+
+static struct resource da9061_onkey_resources[] = {
+ DEFINE_RES_IRQ_NAMED(DA9061_IRQ_ONKEY, "ONKEY"),
+};
+
+static const struct mfd_cell da9061_devs[] = {
+ {
+ .name = "da9061-core",
+ .num_resources = ARRAY_SIZE(da9061_core_resources),
+ .resources = da9061_core_resources,
+ },
+ {
+ .name = "da9062-regulators",
+ .num_resources = ARRAY_SIZE(da9061_regulators_resources),
+ .resources = da9061_regulators_resources,
+ },
+ {
+ .name = "da9061-watchdog",
+ .num_resources = ARRAY_SIZE(da9061_wdt_resources),
+ .resources = da9061_wdt_resources,
+ .of_compatible = "dlg,da9061-watchdog",
+ },
+ {
+ .name = "da9061-thermal",
+ .num_resources = ARRAY_SIZE(da9061_thermal_resources),
+ .resources = da9061_thermal_resources,
+ .of_compatible = "dlg,da9061-thermal",
+ },
+ {
+ .name = "da9061-onkey",
+ .num_resources = ARRAY_SIZE(da9061_onkey_resources),
+ .resources = da9061_onkey_resources,
+ .of_compatible = "dlg,da9061-onkey",
+ },
+};
+
static struct resource da9062_core_resources[] = {
DEFINE_RES_NAMED(DA9062_IRQ_VDD_WARN, 1, "VDD_WARN", IORESOURCE_IRQ),
};
@@ -200,7 +315,8 @@ static int da9062_clear_fault_log(struct da9062 *chip)
static int da9062_get_device_type(struct da9062 *chip)
{
- int device_id, variant_id, variant_mrc;
+ int device_id, variant_id, variant_mrc, variant_vrc;
+ char *type;
int ret;
ret = regmap_read(chip->regmap, DA9062AA_DEVICE_ID, &device_id);
@@ -219,9 +335,23 @@ static int da9062_get_device_type(struct da9062 *chip)
return -EIO;
}
+ variant_vrc = (variant_id & DA9062AA_VRC_MASK) >> DA9062AA_VRC_SHIFT;
+
+ switch (variant_vrc) {
+ case DA9062_PMIC_VARIANT_VRC_DA9061:
+ type = "DA9061";
+ break;
+ case DA9062_PMIC_VARIANT_VRC_DA9062:
+ type = "DA9062";
+ break;
+ default:
+ type = "Unknown";
+ break;
+ }
+
dev_info(chip->dev,
- "Device detected (device-ID: 0x%02X, var-ID: 0x%02X)\n",
- device_id, variant_id);
+ "Device detected (device-ID: 0x%02X, var-ID: 0x%02X, %s)\n",
+ device_id, variant_id, type);
variant_mrc = (variant_id & DA9062AA_MRC_MASK) >> DA9062AA_MRC_SHIFT;
@@ -234,6 +364,234 @@ static int da9062_get_device_type(struct da9062 *chip)
return ret;
}
+static const struct regmap_range da9061_aa_readable_ranges[] = {
+ {
+ .range_min = DA9062AA_PAGE_CON,
+ .range_max = DA9062AA_STATUS_B,
+ }, {
+ .range_min = DA9062AA_STATUS_D,
+ .range_max = DA9062AA_EVENT_C,
+ }, {
+ .range_min = DA9062AA_IRQ_MASK_A,
+ .range_max = DA9062AA_IRQ_MASK_C,
+ }, {
+ .range_min = DA9062AA_CONTROL_A,
+ .range_max = DA9062AA_GPIO_4,
+ }, {
+ .range_min = DA9062AA_GPIO_WKUP_MODE,
+ .range_max = DA9062AA_GPIO_OUT3_4,
+ }, {
+ .range_min = DA9062AA_BUCK1_CONT,
+ .range_max = DA9062AA_BUCK4_CONT,
+ }, {
+ .range_min = DA9062AA_BUCK3_CONT,
+ .range_max = DA9062AA_BUCK3_CONT,
+ }, {
+ .range_min = DA9062AA_LDO1_CONT,
+ .range_max = DA9062AA_LDO4_CONT,
+ }, {
+ .range_min = DA9062AA_DVC_1,
+ .range_max = DA9062AA_DVC_1,
+ }, {
+ .range_min = DA9062AA_SEQ,
+ .range_max = DA9062AA_ID_4_3,
+ }, {
+ .range_min = DA9062AA_ID_12_11,
+ .range_max = DA9062AA_ID_16_15,
+ }, {
+ .range_min = DA9062AA_ID_22_21,
+ .range_max = DA9062AA_ID_32_31,
+ }, {
+ .range_min = DA9062AA_SEQ_A,
+ .range_max = DA9062AA_WAIT,
+ }, {
+ .range_min = DA9062AA_RESET,
+ .range_max = DA9062AA_BUCK_ILIM_C,
+ }, {
+ .range_min = DA9062AA_BUCK1_CFG,
+ .range_max = DA9062AA_BUCK3_CFG,
+ }, {
+ .range_min = DA9062AA_VBUCK1_A,
+ .range_max = DA9062AA_VBUCK4_A,
+ }, {
+ .range_min = DA9062AA_VBUCK3_A,
+ .range_max = DA9062AA_VBUCK3_A,
+ }, {
+ .range_min = DA9062AA_VLDO1_A,
+ .range_max = DA9062AA_VLDO4_A,
+ }, {
+ .range_min = DA9062AA_VBUCK1_B,
+ .range_max = DA9062AA_VBUCK4_B,
+ }, {
+ .range_min = DA9062AA_VBUCK3_B,
+ .range_max = DA9062AA_VBUCK3_B,
+ }, {
+ .range_min = DA9062AA_VLDO1_B,
+ .range_max = DA9062AA_VLDO4_B,
+ }, {
+ .range_min = DA9062AA_BBAT_CONT,
+ .range_max = DA9062AA_BBAT_CONT,
+ }, {
+ .range_min = DA9062AA_INTERFACE,
+ .range_max = DA9062AA_CONFIG_E,
+ }, {
+ .range_min = DA9062AA_CONFIG_G,
+ .range_max = DA9062AA_CONFIG_K,
+ }, {
+ .range_min = DA9062AA_CONFIG_M,
+ .range_max = DA9062AA_CONFIG_M,
+ }, {
+ .range_min = DA9062AA_GP_ID_0,
+ .range_max = DA9062AA_GP_ID_19,
+ }, {
+ .range_min = DA9062AA_DEVICE_ID,
+ .range_max = DA9062AA_CONFIG_ID,
+ },
+};
+
+static const struct regmap_range da9061_aa_writeable_ranges[] = {
+ {
+ .range_min = DA9062AA_PAGE_CON,
+ .range_max = DA9062AA_PAGE_CON,
+ }, {
+ .range_min = DA9062AA_FAULT_LOG,
+ .range_max = DA9062AA_EVENT_C,
+ }, {
+ .range_min = DA9062AA_IRQ_MASK_A,
+ .range_max = DA9062AA_IRQ_MASK_C,
+ }, {
+ .range_min = DA9062AA_CONTROL_A,
+ .range_max = DA9062AA_GPIO_4,
+ }, {
+ .range_min = DA9062AA_GPIO_WKUP_MODE,
+ .range_max = DA9062AA_GPIO_OUT3_4,
+ }, {
+ .range_min = DA9062AA_BUCK1_CONT,
+ .range_max = DA9062AA_BUCK4_CONT,
+ }, {
+ .range_min = DA9062AA_BUCK3_CONT,
+ .range_max = DA9062AA_BUCK3_CONT,
+ }, {
+ .range_min = DA9062AA_LDO1_CONT,
+ .range_max = DA9062AA_LDO4_CONT,
+ }, {
+ .range_min = DA9062AA_DVC_1,
+ .range_max = DA9062AA_DVC_1,
+ }, {
+ .range_min = DA9062AA_SEQ,
+ .range_max = DA9062AA_ID_4_3,
+ }, {
+ .range_min = DA9062AA_ID_12_11,
+ .range_max = DA9062AA_ID_16_15,
+ }, {
+ .range_min = DA9062AA_ID_22_21,
+ .range_max = DA9062AA_ID_32_31,
+ }, {
+ .range_min = DA9062AA_SEQ_A,
+ .range_max = DA9062AA_WAIT,
+ }, {
+ .range_min = DA9062AA_RESET,
+ .range_max = DA9062AA_BUCK_ILIM_C,
+ }, {
+ .range_min = DA9062AA_BUCK1_CFG,
+ .range_max = DA9062AA_BUCK3_CFG,
+ }, {
+ .range_min = DA9062AA_VBUCK1_A,
+ .range_max = DA9062AA_VBUCK4_A,
+ }, {
+ .range_min = DA9062AA_VBUCK3_A,
+ .range_max = DA9062AA_VBUCK3_A,
+ }, {
+ .range_min = DA9062AA_VLDO1_A,
+ .range_max = DA9062AA_VLDO4_A,
+ }, {
+ .range_min = DA9062AA_VBUCK1_B,
+ .range_max = DA9062AA_VBUCK4_B,
+ }, {
+ .range_min = DA9062AA_VBUCK3_B,
+ .range_max = DA9062AA_VBUCK3_B,
+ }, {
+ .range_min = DA9062AA_VLDO1_B,
+ .range_max = DA9062AA_VLDO4_B,
+ }, {
+ .range_min = DA9062AA_BBAT_CONT,
+ .range_max = DA9062AA_BBAT_CONT,
+ }, {
+ .range_min = DA9062AA_GP_ID_0,
+ .range_max = DA9062AA_GP_ID_19,
+ },
+};
+
+static const struct regmap_range da9061_aa_volatile_ranges[] = {
+ {
+ .range_min = DA9062AA_PAGE_CON,
+ .range_max = DA9062AA_STATUS_B,
+ }, {
+ .range_min = DA9062AA_STATUS_D,
+ .range_max = DA9062AA_EVENT_C,
+ }, {
+ .range_min = DA9062AA_CONTROL_A,
+ .range_max = DA9062AA_CONTROL_B,
+ }, {
+ .range_min = DA9062AA_CONTROL_E,
+ .range_max = DA9062AA_CONTROL_F,
+ }, {
+ .range_min = DA9062AA_BUCK1_CONT,
+ .range_max = DA9062AA_BUCK4_CONT,
+ }, {
+ .range_min = DA9062AA_BUCK3_CONT,
+ .range_max = DA9062AA_BUCK3_CONT,
+ }, {
+ .range_min = DA9062AA_LDO1_CONT,
+ .range_max = DA9062AA_LDO4_CONT,
+ }, {
+ .range_min = DA9062AA_DVC_1,
+ .range_max = DA9062AA_DVC_1,
+ }, {
+ .range_min = DA9062AA_SEQ,
+ .range_max = DA9062AA_SEQ,
+ },
+};
+
+static const struct regmap_access_table da9061_aa_readable_table = {
+ .yes_ranges = da9061_aa_readable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(da9061_aa_readable_ranges),
+};
+
+static const struct regmap_access_table da9061_aa_writeable_table = {
+ .yes_ranges = da9061_aa_writeable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(da9061_aa_writeable_ranges),
+};
+
+static const struct regmap_access_table da9061_aa_volatile_table = {
+ .yes_ranges = da9061_aa_volatile_ranges,
+ .n_yes_ranges = ARRAY_SIZE(da9061_aa_volatile_ranges),
+};
+
+static const struct regmap_range_cfg da9061_range_cfg[] = {
+ {
+ .range_min = DA9062AA_PAGE_CON,
+ .range_max = DA9062AA_CONFIG_ID,
+ .selector_reg = DA9062AA_PAGE_CON,
+ .selector_mask = 1 << DA9062_I2C_PAGE_SEL_SHIFT,
+ .selector_shift = DA9062_I2C_PAGE_SEL_SHIFT,
+ .window_start = 0,
+ .window_len = 256,
+ }
+};
+
+static struct regmap_config da9061_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .ranges = da9061_range_cfg,
+ .num_ranges = ARRAY_SIZE(da9061_range_cfg),
+ .max_register = DA9062AA_CONFIG_ID,
+ .cache_type = REGCACHE_RBTREE,
+ .rd_table = &da9061_aa_readable_table,
+ .wr_table = &da9061_aa_writeable_table,
+ .volatile_table = &da9061_aa_volatile_table,
+};
+
static const struct regmap_range da9062_aa_readable_ranges[] = {
{
.range_min = DA9062AA_PAGE_CON,
@@ -456,17 +814,39 @@ static int da9062_get_device_type(struct da9062 *chip)
.volatile_table = &da9062_aa_volatile_table,
};
+static const struct of_device_id da9062_dt_ids[] = {
+ { .compatible = "dlg,da9061", .data = (void *)COMPAT_TYPE_DA9061, },
+ { .compatible = "dlg,da9062", .data = (void *)COMPAT_TYPE_DA9062, },
+ { }
+};
+MODULE_DEVICE_TABLE(of, da9062_dt_ids);
+
static int da9062_i2c_probe(struct i2c_client *i2c,
const struct i2c_device_id *id)
{
struct da9062 *chip;
+ const struct of_device_id *match;
unsigned int irq_base;
+ const struct mfd_cell *cell;
+ const struct regmap_irq_chip *irq_chip;
+ const struct regmap_config *config;
+ int cell_num;
int ret;
chip = devm_kzalloc(&i2c->dev, sizeof(*chip), GFP_KERNEL);
if (!chip)
return -ENOMEM;
+ if (i2c->dev.of_node) {
+ match = of_match_node(da9062_dt_ids, i2c->dev.of_node);
+ if (!match)
+ return -EINVAL;
+
+ chip->chip_type = (uintptr_t)match->data;
+ } else {
+ chip->chip_type = id->driver_data;
+ }
+
i2c_set_clientdata(i2c, chip);
chip->dev = &i2c->dev;
@@ -475,7 +855,25 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
return -EINVAL;
}
- chip->regmap = devm_regmap_init_i2c(i2c, &da9062_regmap_config);
+ switch (chip->chip_type) {
+ case(COMPAT_TYPE_DA9061):
+ cell = da9061_devs;
+ cell_num = ARRAY_SIZE(da9061_devs);
+ irq_chip = &da9061_irq_chip;
+ config = &da9061_regmap_config;
+ break;
+ case(COMPAT_TYPE_DA9062):
+ cell = da9062_devs;
+ cell_num = ARRAY_SIZE(da9062_devs);
+ irq_chip = &da9062_irq_chip;
+ config = &da9062_regmap_config;
+ break;
+ default:
+ dev_err(chip->dev, "Unrecognised chip type\n");
+ return -ENODEV;
+ }
+
+ chip->regmap = devm_regmap_init_i2c(i2c, config);
if (IS_ERR(chip->regmap)) {
ret = PTR_ERR(chip->regmap);
dev_err(chip->dev, "Failed to allocate register map: %d\n",
@@ -493,7 +891,7 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
ret = regmap_add_irq_chip(chip->regmap, i2c->irq,
IRQF_TRIGGER_LOW | IRQF_ONESHOT | IRQF_SHARED,
- -1, &da9062_irq_chip,
+ -1, irq_chip,
&chip->regmap_irq);
if (ret) {
dev_err(chip->dev, "Failed to request IRQ %d: %d\n",
@@ -503,8 +901,8 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
irq_base = regmap_irq_chip_get_base(chip->regmap_irq);
- ret = mfd_add_devices(chip->dev, PLATFORM_DEVID_NONE, da9062_devs,
- ARRAY_SIZE(da9062_devs), NULL, irq_base,
+ ret = mfd_add_devices(chip->dev, PLATFORM_DEVID_NONE, cell,
+ cell_num, NULL, irq_base,
NULL);
if (ret) {
dev_err(chip->dev, "Cannot register child devices\n");
@@ -526,17 +924,12 @@ static int da9062_i2c_remove(struct i2c_client *i2c)
}
static const struct i2c_device_id da9062_i2c_id[] = {
- { "da9062", 0 },
+ { "da9061", COMPAT_TYPE_DA9061 },
+ { "da9062", COMPAT_TYPE_DA9062 },
{ },
};
MODULE_DEVICE_TABLE(i2c, da9062_i2c_id);
-static const struct of_device_id da9062_dt_ids[] = {
- { .compatible = "dlg,da9062", },
- { }
-};
-MODULE_DEVICE_TABLE(of, da9062_dt_ids);
-
static struct i2c_driver da9062_i2c_driver = {
.driver = {
.name = "da9062",
@@ -549,6 +942,6 @@ static int da9062_i2c_remove(struct i2c_client *i2c)
module_i2c_driver(da9062_i2c_driver);
-MODULE_DESCRIPTION("Core device driver for Dialog DA9062");
+MODULE_DESCRIPTION("Core device driver for Dialog DA9061 and DA9062");
MODULE_AUTHOR("Steve Twiss <stwiss.opensource@diasemi.com>");
MODULE_LICENSE("GPL");
diff --git a/include/linux/mfd/da9062/core.h b/include/linux/mfd/da9062/core.h
index 376ba84..74d33a0 100644
--- a/include/linux/mfd/da9062/core.h
+++ b/include/linux/mfd/da9062/core.h
@@ -1,5 +1,5 @@
/*
- * Copyright (C) 2015 Dialog Semiconductor Ltd.
+ * Copyright (C) 2015-2017 Dialog Semiconductor
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
@@ -18,7 +18,31 @@
#include <linux/interrupt.h>
#include <linux/mfd/da9062/registers.h>
-/* Interrupts */
+enum da9062_compatible_types {
+ COMPAT_TYPE_DA9061 = 1,
+ COMPAT_TYPE_DA9062,
+};
+
+enum da9061_irqs {
+ /* IRQ A */
+ DA9061_IRQ_ONKEY,
+ DA9061_IRQ_WDG_WARN,
+ DA9061_IRQ_SEQ_RDY,
+ /* IRQ B*/
+ DA9061_IRQ_TEMP,
+ DA9061_IRQ_LDO_LIM,
+ DA9061_IRQ_DVC_RDY,
+ DA9061_IRQ_VDD_WARN,
+ /* IRQ C */
+ DA9061_IRQ_GPI0,
+ DA9061_IRQ_GPI1,
+ DA9061_IRQ_GPI2,
+ DA9061_IRQ_GPI3,
+ DA9061_IRQ_GPI4,
+
+ DA9061_NUM_IRQ,
+};
+
enum da9062_irqs {
/* IRQ A */
DA9062_IRQ_ONKEY,
@@ -45,6 +69,7 @@ struct da9062 {
struct device *dev;
struct regmap *regmap;
struct regmap_irq_chip_data *regmap_irq;
+ enum da9062_compatible_types chip_type;
};
#endif /* __MFD_DA9062_CORE_H__ */
diff --git a/include/linux/mfd/da9062/registers.h b/include/linux/mfd/da9062/registers.h
index 97790d1..18d576a 100644
--- a/include/linux/mfd/da9062/registers.h
+++ b/include/linux/mfd/da9062/registers.h
@@ -1,6 +1,5 @@
/*
- * registers.h - REGISTERS H for DA9062
- * Copyright (C) 2015 Dialog Semiconductor Ltd.
+ * Copyright (C) 2015-2017 Dialog Semiconductor
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
@@ -18,6 +17,8 @@
#define DA9062_PMIC_DEVICE_ID 0x62
#define DA9062_PMIC_VARIANT_MRC_AA 0x01
+#define DA9062_PMIC_VARIANT_VRC_DA9061 0x01
+#define DA9062_PMIC_VARIANT_VRC_DA9062 0x02
#define DA9062_I2C_PAGE_SEL_SHIFT 1
--
end-of-patch for PATCH V7
^ permalink raw reply related [flat|nested] 36+ messages in thread* [PATCH V7 4/7] mfd: da9061: MFD core support
@ 2017-03-28 14:43 ` Steve Twiss
0 siblings, 0 replies; 36+ messages in thread
From: Steve Twiss @ 2017-03-28 14:43 UTC (permalink / raw)
To: LINUX-KERNEL, Lee Jones
Cc: DEVICETREE, Dmitry Torokhov, Eduardo Valentin, Guenter Roeck,
LINUX-INPUT, LINUX-PM, LINUX-WATCHDOG, Liam Girdwood, Mark Brown,
Mark Rutland, Rob Herring, Support Opensource, Wim Van Sebroeck,
Zhang Rui
From: Steve Twiss <stwiss.opensource-WBD+wuPFNBhBDgjK7y7TUQ@public.gmane.org>
MFD support for DA9061 is provided as part of the DA9062 device driver.
The registers header file adds two new chip variant IDs defined in DA9061
and DA9062 hardware. The core header file adds new software enumerations
for listing the valid DA9061 IRQs and a da9062_compatible_types enumeration
for distinguishing between DA9061/62 devices in software.
The core source code adds a new .compatible of_device_id entry. This is
extended from DA9062 to support both "dlg,da9061" and "dlg,da9062". The
.data entry now holds a reference to the enumerated device type.
A new regmap_irq_chip model is added for DA9061 and this supports the new
list of regmap_irq entries. A new mfd_cell da9061_devs[] array lists the
new sub system components for DA9061. Support is added for a new DA9061
regmap_config which lists the correct readable, writable and volatile
ranges for this chip.
The probe function uses the device tree compatible string to switch on the
da9062_compatible_types and configure the correct mfd cells, irq chip and
regmap config.
Kconfig is updated to reflect support for DA9061 and DA9062 PMICs.
Signed-off-by: Steve Twiss <stwiss.opensource-WBD+wuPFNBhBDgjK7y7TUQ@public.gmane.org>
---
Acked-for-mfd-by: Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Hi Lee, that Ack was from your earlier posting:
https://lkml.org/lkml/2017/1/4/328 this was
Regards, Steve.
This patch applies against linux-next and v4.11-rc3
v6 -> v7
- Remove compilation warning when casting a void * to an integer on
ARCH=x86_64 using -Wpointer-to-int-cast.
- Recommendation uintptr_t cast: https://lkml.org/lkml/2017/3/28/292
- Compile tested ARCH=x86_64
v5 -> v6
- Rebased from v4.9 to v4.11-rc3
- Modify Copyright to match Dialog latest legal statement
- Fixed "braces {} should be used on all arms" checkpatch warning
v4 -> v5
- NO CODE CHANGE
- Rebased from v4.8 to v4.9
v3 -> v4
- Patch renamed from [PATCH V3 5/9] to [PATCH V4 4/8]
- Removed DEFINE_RES_NAMED() macros for DA9061 resources and replaced
them with DEFINE_RES_IRQ_NAMED().
- Removed whitespace
- Reverted change for badly defined mfd_cell da9062_devs of_compatible
string from "dlg,da9062-watchdog" back to "dlg,da9062-wdt"
v2 -> v3
- NO CODE CHANGE
- Patch renamed from [PATCH V2 05/10] to [PATCH V3 5/9]
v1 -> v2
- Patch renamed from [PATCH V1 01/10] to [PATCH V2 05/10] -- these
changes were made to fix checkpatch warnings caused by the patch
set dependency order
- Fixed typo in the commit message "readble" to "readable"
- Removed the explicit cross-check to decide if there is a conflict
between the device tree compatible string and the hardware definition.
This patch assumes the device tree is correctly written and therefore
removes the need for a hardware/DT sanity check.
- Removed extra semicolon in drivers/mfd/da9062-core.c:877
- Re-write compatible entries into numerical order
Lee,
Changes as described in the version history above.
As previously:
This patch adds support for the DA9061 PMIC. This is done as part of the
existing DA9062 device driver by extending the of_device_id match table.
This in turn allows new MFD cells, irq chip and regmap definitions to
support DA9061.
Regards,
Steve Twiss, Dialog Semiconductor
drivers/mfd/Kconfig | 5 +-
drivers/mfd/da9062-core.c | 427 +++++++++++++++++++++++++++++++++--
include/linux/mfd/da9062/core.h | 29 ++-
include/linux/mfd/da9062/registers.h | 5 +-
4 files changed, 443 insertions(+), 23 deletions(-)
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 55ecdfb..29cc11a 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -263,13 +263,14 @@ config MFD_DA9055
called "da9055"
config MFD_DA9062
- tristate "Dialog Semiconductor DA9062 PMIC Support"
+ tristate "Dialog Semiconductor DA9062/61 PMIC Support"
select MFD_CORE
select REGMAP_I2C
select REGMAP_IRQ
depends on I2C
help
- Say yes here for support for the Dialog Semiconductor DA9062 PMIC.
+ Say yes here for support for the Dialog Semiconductor DA9061 and
+ DA9062 PMICs.
This includes the I2C driver and core APIs.
Additional drivers must be enabled in order to use the functionality
of the device.
diff --git a/drivers/mfd/da9062-core.c b/drivers/mfd/da9062-core.c
index 8f873866..78ab3f4 100644
--- a/drivers/mfd/da9062-core.c
+++ b/drivers/mfd/da9062-core.c
@@ -1,6 +1,6 @@
/*
- * Core, IRQ and I2C device driver for DA9062 PMIC
- * Copyright (C) 2015 Dialog Semiconductor Ltd.
+ * Core, IRQ and I2C device driver for DA9061 and DA9062 PMICs
+ * Copyright (C) 2015-2017 Dialog Semiconductor
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
@@ -30,6 +30,70 @@
#define DA9062_REG_EVENT_B_OFFSET 1
#define DA9062_REG_EVENT_C_OFFSET 2
+static struct regmap_irq da9061_irqs[] = {
+ /* EVENT A */
+ [DA9061_IRQ_ONKEY] = {
+ .reg_offset = DA9062_REG_EVENT_A_OFFSET,
+ .mask = DA9062AA_M_NONKEY_MASK,
+ },
+ [DA9061_IRQ_WDG_WARN] = {
+ .reg_offset = DA9062_REG_EVENT_A_OFFSET,
+ .mask = DA9062AA_M_WDG_WARN_MASK,
+ },
+ [DA9061_IRQ_SEQ_RDY] = {
+ .reg_offset = DA9062_REG_EVENT_A_OFFSET,
+ .mask = DA9062AA_M_SEQ_RDY_MASK,
+ },
+ /* EVENT B */
+ [DA9061_IRQ_TEMP] = {
+ .reg_offset = DA9062_REG_EVENT_B_OFFSET,
+ .mask = DA9062AA_M_TEMP_MASK,
+ },
+ [DA9061_IRQ_LDO_LIM] = {
+ .reg_offset = DA9062_REG_EVENT_B_OFFSET,
+ .mask = DA9062AA_M_LDO_LIM_MASK,
+ },
+ [DA9061_IRQ_DVC_RDY] = {
+ .reg_offset = DA9062_REG_EVENT_B_OFFSET,
+ .mask = DA9062AA_M_DVC_RDY_MASK,
+ },
+ [DA9061_IRQ_VDD_WARN] = {
+ .reg_offset = DA9062_REG_EVENT_B_OFFSET,
+ .mask = DA9062AA_M_VDD_WARN_MASK,
+ },
+ /* EVENT C */
+ [DA9061_IRQ_GPI0] = {
+ .reg_offset = DA9062_REG_EVENT_C_OFFSET,
+ .mask = DA9062AA_M_GPI0_MASK,
+ },
+ [DA9061_IRQ_GPI1] = {
+ .reg_offset = DA9062_REG_EVENT_C_OFFSET,
+ .mask = DA9062AA_M_GPI1_MASK,
+ },
+ [DA9061_IRQ_GPI2] = {
+ .reg_offset = DA9062_REG_EVENT_C_OFFSET,
+ .mask = DA9062AA_M_GPI2_MASK,
+ },
+ [DA9061_IRQ_GPI3] = {
+ .reg_offset = DA9062_REG_EVENT_C_OFFSET,
+ .mask = DA9062AA_M_GPI3_MASK,
+ },
+ [DA9061_IRQ_GPI4] = {
+ .reg_offset = DA9062_REG_EVENT_C_OFFSET,
+ .mask = DA9062AA_M_GPI4_MASK,
+ },
+};
+
+static struct regmap_irq_chip da9061_irq_chip = {
+ .name = "da9061-irq",
+ .irqs = da9061_irqs,
+ .num_irqs = DA9061_NUM_IRQ,
+ .num_regs = 3,
+ .status_base = DA9062AA_EVENT_A,
+ .mask_base = DA9062AA_IRQ_MASK_A,
+ .ack_base = DA9062AA_EVENT_A,
+};
+
static struct regmap_irq da9062_irqs[] = {
/* EVENT A */
[DA9062_IRQ_ONKEY] = {
@@ -102,6 +166,57 @@
.ack_base = DA9062AA_EVENT_A,
};
+static struct resource da9061_core_resources[] = {
+ DEFINE_RES_IRQ_NAMED(DA9061_IRQ_VDD_WARN, "VDD_WARN"),
+};
+
+static struct resource da9061_regulators_resources[] = {
+ DEFINE_RES_IRQ_NAMED(DA9061_IRQ_LDO_LIM, "LDO_LIM"),
+};
+
+static struct resource da9061_thermal_resources[] = {
+ DEFINE_RES_IRQ_NAMED(DA9061_IRQ_TEMP, "THERMAL"),
+};
+
+static struct resource da9061_wdt_resources[] = {
+ DEFINE_RES_IRQ_NAMED(DA9061_IRQ_WDG_WARN, "WD_WARN"),
+};
+
+static struct resource da9061_onkey_resources[] = {
+ DEFINE_RES_IRQ_NAMED(DA9061_IRQ_ONKEY, "ONKEY"),
+};
+
+static const struct mfd_cell da9061_devs[] = {
+ {
+ .name = "da9061-core",
+ .num_resources = ARRAY_SIZE(da9061_core_resources),
+ .resources = da9061_core_resources,
+ },
+ {
+ .name = "da9062-regulators",
+ .num_resources = ARRAY_SIZE(da9061_regulators_resources),
+ .resources = da9061_regulators_resources,
+ },
+ {
+ .name = "da9061-watchdog",
+ .num_resources = ARRAY_SIZE(da9061_wdt_resources),
+ .resources = da9061_wdt_resources,
+ .of_compatible = "dlg,da9061-watchdog",
+ },
+ {
+ .name = "da9061-thermal",
+ .num_resources = ARRAY_SIZE(da9061_thermal_resources),
+ .resources = da9061_thermal_resources,
+ .of_compatible = "dlg,da9061-thermal",
+ },
+ {
+ .name = "da9061-onkey",
+ .num_resources = ARRAY_SIZE(da9061_onkey_resources),
+ .resources = da9061_onkey_resources,
+ .of_compatible = "dlg,da9061-onkey",
+ },
+};
+
static struct resource da9062_core_resources[] = {
DEFINE_RES_NAMED(DA9062_IRQ_VDD_WARN, 1, "VDD_WARN", IORESOURCE_IRQ),
};
@@ -200,7 +315,8 @@ static int da9062_clear_fault_log(struct da9062 *chip)
static int da9062_get_device_type(struct da9062 *chip)
{
- int device_id, variant_id, variant_mrc;
+ int device_id, variant_id, variant_mrc, variant_vrc;
+ char *type;
int ret;
ret = regmap_read(chip->regmap, DA9062AA_DEVICE_ID, &device_id);
@@ -219,9 +335,23 @@ static int da9062_get_device_type(struct da9062 *chip)
return -EIO;
}
+ variant_vrc = (variant_id & DA9062AA_VRC_MASK) >> DA9062AA_VRC_SHIFT;
+
+ switch (variant_vrc) {
+ case DA9062_PMIC_VARIANT_VRC_DA9061:
+ type = "DA9061";
+ break;
+ case DA9062_PMIC_VARIANT_VRC_DA9062:
+ type = "DA9062";
+ break;
+ default:
+ type = "Unknown";
+ break;
+ }
+
dev_info(chip->dev,
- "Device detected (device-ID: 0x%02X, var-ID: 0x%02X)\n",
- device_id, variant_id);
+ "Device detected (device-ID: 0x%02X, var-ID: 0x%02X, %s)\n",
+ device_id, variant_id, type);
variant_mrc = (variant_id & DA9062AA_MRC_MASK) >> DA9062AA_MRC_SHIFT;
@@ -234,6 +364,234 @@ static int da9062_get_device_type(struct da9062 *chip)
return ret;
}
+static const struct regmap_range da9061_aa_readable_ranges[] = {
+ {
+ .range_min = DA9062AA_PAGE_CON,
+ .range_max = DA9062AA_STATUS_B,
+ }, {
+ .range_min = DA9062AA_STATUS_D,
+ .range_max = DA9062AA_EVENT_C,
+ }, {
+ .range_min = DA9062AA_IRQ_MASK_A,
+ .range_max = DA9062AA_IRQ_MASK_C,
+ }, {
+ .range_min = DA9062AA_CONTROL_A,
+ .range_max = DA9062AA_GPIO_4,
+ }, {
+ .range_min = DA9062AA_GPIO_WKUP_MODE,
+ .range_max = DA9062AA_GPIO_OUT3_4,
+ }, {
+ .range_min = DA9062AA_BUCK1_CONT,
+ .range_max = DA9062AA_BUCK4_CONT,
+ }, {
+ .range_min = DA9062AA_BUCK3_CONT,
+ .range_max = DA9062AA_BUCK3_CONT,
+ }, {
+ .range_min = DA9062AA_LDO1_CONT,
+ .range_max = DA9062AA_LDO4_CONT,
+ }, {
+ .range_min = DA9062AA_DVC_1,
+ .range_max = DA9062AA_DVC_1,
+ }, {
+ .range_min = DA9062AA_SEQ,
+ .range_max = DA9062AA_ID_4_3,
+ }, {
+ .range_min = DA9062AA_ID_12_11,
+ .range_max = DA9062AA_ID_16_15,
+ }, {
+ .range_min = DA9062AA_ID_22_21,
+ .range_max = DA9062AA_ID_32_31,
+ }, {
+ .range_min = DA9062AA_SEQ_A,
+ .range_max = DA9062AA_WAIT,
+ }, {
+ .range_min = DA9062AA_RESET,
+ .range_max = DA9062AA_BUCK_ILIM_C,
+ }, {
+ .range_min = DA9062AA_BUCK1_CFG,
+ .range_max = DA9062AA_BUCK3_CFG,
+ }, {
+ .range_min = DA9062AA_VBUCK1_A,
+ .range_max = DA9062AA_VBUCK4_A,
+ }, {
+ .range_min = DA9062AA_VBUCK3_A,
+ .range_max = DA9062AA_VBUCK3_A,
+ }, {
+ .range_min = DA9062AA_VLDO1_A,
+ .range_max = DA9062AA_VLDO4_A,
+ }, {
+ .range_min = DA9062AA_VBUCK1_B,
+ .range_max = DA9062AA_VBUCK4_B,
+ }, {
+ .range_min = DA9062AA_VBUCK3_B,
+ .range_max = DA9062AA_VBUCK3_B,
+ }, {
+ .range_min = DA9062AA_VLDO1_B,
+ .range_max = DA9062AA_VLDO4_B,
+ }, {
+ .range_min = DA9062AA_BBAT_CONT,
+ .range_max = DA9062AA_BBAT_CONT,
+ }, {
+ .range_min = DA9062AA_INTERFACE,
+ .range_max = DA9062AA_CONFIG_E,
+ }, {
+ .range_min = DA9062AA_CONFIG_G,
+ .range_max = DA9062AA_CONFIG_K,
+ }, {
+ .range_min = DA9062AA_CONFIG_M,
+ .range_max = DA9062AA_CONFIG_M,
+ }, {
+ .range_min = DA9062AA_GP_ID_0,
+ .range_max = DA9062AA_GP_ID_19,
+ }, {
+ .range_min = DA9062AA_DEVICE_ID,
+ .range_max = DA9062AA_CONFIG_ID,
+ },
+};
+
+static const struct regmap_range da9061_aa_writeable_ranges[] = {
+ {
+ .range_min = DA9062AA_PAGE_CON,
+ .range_max = DA9062AA_PAGE_CON,
+ }, {
+ .range_min = DA9062AA_FAULT_LOG,
+ .range_max = DA9062AA_EVENT_C,
+ }, {
+ .range_min = DA9062AA_IRQ_MASK_A,
+ .range_max = DA9062AA_IRQ_MASK_C,
+ }, {
+ .range_min = DA9062AA_CONTROL_A,
+ .range_max = DA9062AA_GPIO_4,
+ }, {
+ .range_min = DA9062AA_GPIO_WKUP_MODE,
+ .range_max = DA9062AA_GPIO_OUT3_4,
+ }, {
+ .range_min = DA9062AA_BUCK1_CONT,
+ .range_max = DA9062AA_BUCK4_CONT,
+ }, {
+ .range_min = DA9062AA_BUCK3_CONT,
+ .range_max = DA9062AA_BUCK3_CONT,
+ }, {
+ .range_min = DA9062AA_LDO1_CONT,
+ .range_max = DA9062AA_LDO4_CONT,
+ }, {
+ .range_min = DA9062AA_DVC_1,
+ .range_max = DA9062AA_DVC_1,
+ }, {
+ .range_min = DA9062AA_SEQ,
+ .range_max = DA9062AA_ID_4_3,
+ }, {
+ .range_min = DA9062AA_ID_12_11,
+ .range_max = DA9062AA_ID_16_15,
+ }, {
+ .range_min = DA9062AA_ID_22_21,
+ .range_max = DA9062AA_ID_32_31,
+ }, {
+ .range_min = DA9062AA_SEQ_A,
+ .range_max = DA9062AA_WAIT,
+ }, {
+ .range_min = DA9062AA_RESET,
+ .range_max = DA9062AA_BUCK_ILIM_C,
+ }, {
+ .range_min = DA9062AA_BUCK1_CFG,
+ .range_max = DA9062AA_BUCK3_CFG,
+ }, {
+ .range_min = DA9062AA_VBUCK1_A,
+ .range_max = DA9062AA_VBUCK4_A,
+ }, {
+ .range_min = DA9062AA_VBUCK3_A,
+ .range_max = DA9062AA_VBUCK3_A,
+ }, {
+ .range_min = DA9062AA_VLDO1_A,
+ .range_max = DA9062AA_VLDO4_A,
+ }, {
+ .range_min = DA9062AA_VBUCK1_B,
+ .range_max = DA9062AA_VBUCK4_B,
+ }, {
+ .range_min = DA9062AA_VBUCK3_B,
+ .range_max = DA9062AA_VBUCK3_B,
+ }, {
+ .range_min = DA9062AA_VLDO1_B,
+ .range_max = DA9062AA_VLDO4_B,
+ }, {
+ .range_min = DA9062AA_BBAT_CONT,
+ .range_max = DA9062AA_BBAT_CONT,
+ }, {
+ .range_min = DA9062AA_GP_ID_0,
+ .range_max = DA9062AA_GP_ID_19,
+ },
+};
+
+static const struct regmap_range da9061_aa_volatile_ranges[] = {
+ {
+ .range_min = DA9062AA_PAGE_CON,
+ .range_max = DA9062AA_STATUS_B,
+ }, {
+ .range_min = DA9062AA_STATUS_D,
+ .range_max = DA9062AA_EVENT_C,
+ }, {
+ .range_min = DA9062AA_CONTROL_A,
+ .range_max = DA9062AA_CONTROL_B,
+ }, {
+ .range_min = DA9062AA_CONTROL_E,
+ .range_max = DA9062AA_CONTROL_F,
+ }, {
+ .range_min = DA9062AA_BUCK1_CONT,
+ .range_max = DA9062AA_BUCK4_CONT,
+ }, {
+ .range_min = DA9062AA_BUCK3_CONT,
+ .range_max = DA9062AA_BUCK3_CONT,
+ }, {
+ .range_min = DA9062AA_LDO1_CONT,
+ .range_max = DA9062AA_LDO4_CONT,
+ }, {
+ .range_min = DA9062AA_DVC_1,
+ .range_max = DA9062AA_DVC_1,
+ }, {
+ .range_min = DA9062AA_SEQ,
+ .range_max = DA9062AA_SEQ,
+ },
+};
+
+static const struct regmap_access_table da9061_aa_readable_table = {
+ .yes_ranges = da9061_aa_readable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(da9061_aa_readable_ranges),
+};
+
+static const struct regmap_access_table da9061_aa_writeable_table = {
+ .yes_ranges = da9061_aa_writeable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(da9061_aa_writeable_ranges),
+};
+
+static const struct regmap_access_table da9061_aa_volatile_table = {
+ .yes_ranges = da9061_aa_volatile_ranges,
+ .n_yes_ranges = ARRAY_SIZE(da9061_aa_volatile_ranges),
+};
+
+static const struct regmap_range_cfg da9061_range_cfg[] = {
+ {
+ .range_min = DA9062AA_PAGE_CON,
+ .range_max = DA9062AA_CONFIG_ID,
+ .selector_reg = DA9062AA_PAGE_CON,
+ .selector_mask = 1 << DA9062_I2C_PAGE_SEL_SHIFT,
+ .selector_shift = DA9062_I2C_PAGE_SEL_SHIFT,
+ .window_start = 0,
+ .window_len = 256,
+ }
+};
+
+static struct regmap_config da9061_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .ranges = da9061_range_cfg,
+ .num_ranges = ARRAY_SIZE(da9061_range_cfg),
+ .max_register = DA9062AA_CONFIG_ID,
+ .cache_type = REGCACHE_RBTREE,
+ .rd_table = &da9061_aa_readable_table,
+ .wr_table = &da9061_aa_writeable_table,
+ .volatile_table = &da9061_aa_volatile_table,
+};
+
static const struct regmap_range da9062_aa_readable_ranges[] = {
{
.range_min = DA9062AA_PAGE_CON,
@@ -456,17 +814,39 @@ static int da9062_get_device_type(struct da9062 *chip)
.volatile_table = &da9062_aa_volatile_table,
};
+static const struct of_device_id da9062_dt_ids[] = {
+ { .compatible = "dlg,da9061", .data = (void *)COMPAT_TYPE_DA9061, },
+ { .compatible = "dlg,da9062", .data = (void *)COMPAT_TYPE_DA9062, },
+ { }
+};
+MODULE_DEVICE_TABLE(of, da9062_dt_ids);
+
static int da9062_i2c_probe(struct i2c_client *i2c,
const struct i2c_device_id *id)
{
struct da9062 *chip;
+ const struct of_device_id *match;
unsigned int irq_base;
+ const struct mfd_cell *cell;
+ const struct regmap_irq_chip *irq_chip;
+ const struct regmap_config *config;
+ int cell_num;
int ret;
chip = devm_kzalloc(&i2c->dev, sizeof(*chip), GFP_KERNEL);
if (!chip)
return -ENOMEM;
+ if (i2c->dev.of_node) {
+ match = of_match_node(da9062_dt_ids, i2c->dev.of_node);
+ if (!match)
+ return -EINVAL;
+
+ chip->chip_type = (uintptr_t)match->data;
+ } else {
+ chip->chip_type = id->driver_data;
+ }
+
i2c_set_clientdata(i2c, chip);
chip->dev = &i2c->dev;
@@ -475,7 +855,25 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
return -EINVAL;
}
- chip->regmap = devm_regmap_init_i2c(i2c, &da9062_regmap_config);
+ switch (chip->chip_type) {
+ case(COMPAT_TYPE_DA9061):
+ cell = da9061_devs;
+ cell_num = ARRAY_SIZE(da9061_devs);
+ irq_chip = &da9061_irq_chip;
+ config = &da9061_regmap_config;
+ break;
+ case(COMPAT_TYPE_DA9062):
+ cell = da9062_devs;
+ cell_num = ARRAY_SIZE(da9062_devs);
+ irq_chip = &da9062_irq_chip;
+ config = &da9062_regmap_config;
+ break;
+ default:
+ dev_err(chip->dev, "Unrecognised chip type\n");
+ return -ENODEV;
+ }
+
+ chip->regmap = devm_regmap_init_i2c(i2c, config);
if (IS_ERR(chip->regmap)) {
ret = PTR_ERR(chip->regmap);
dev_err(chip->dev, "Failed to allocate register map: %d\n",
@@ -493,7 +891,7 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
ret = regmap_add_irq_chip(chip->regmap, i2c->irq,
IRQF_TRIGGER_LOW | IRQF_ONESHOT | IRQF_SHARED,
- -1, &da9062_irq_chip,
+ -1, irq_chip,
&chip->regmap_irq);
if (ret) {
dev_err(chip->dev, "Failed to request IRQ %d: %d\n",
@@ -503,8 +901,8 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
irq_base = regmap_irq_chip_get_base(chip->regmap_irq);
- ret = mfd_add_devices(chip->dev, PLATFORM_DEVID_NONE, da9062_devs,
- ARRAY_SIZE(da9062_devs), NULL, irq_base,
+ ret = mfd_add_devices(chip->dev, PLATFORM_DEVID_NONE, cell,
+ cell_num, NULL, irq_base,
NULL);
if (ret) {
dev_err(chip->dev, "Cannot register child devices\n");
@@ -526,17 +924,12 @@ static int da9062_i2c_remove(struct i2c_client *i2c)
}
static const struct i2c_device_id da9062_i2c_id[] = {
- { "da9062", 0 },
+ { "da9061", COMPAT_TYPE_DA9061 },
+ { "da9062", COMPAT_TYPE_DA9062 },
{ },
};
MODULE_DEVICE_TABLE(i2c, da9062_i2c_id);
-static const struct of_device_id da9062_dt_ids[] = {
- { .compatible = "dlg,da9062", },
- { }
-};
-MODULE_DEVICE_TABLE(of, da9062_dt_ids);
-
static struct i2c_driver da9062_i2c_driver = {
.driver = {
.name = "da9062",
@@ -549,6 +942,6 @@ static int da9062_i2c_remove(struct i2c_client *i2c)
module_i2c_driver(da9062_i2c_driver);
-MODULE_DESCRIPTION("Core device driver for Dialog DA9062");
+MODULE_DESCRIPTION("Core device driver for Dialog DA9061 and DA9062");
MODULE_AUTHOR("Steve Twiss <stwiss.opensource-WBD+wuPFNBhBDgjK7y7TUQ@public.gmane.org>");
MODULE_LICENSE("GPL");
diff --git a/include/linux/mfd/da9062/core.h b/include/linux/mfd/da9062/core.h
index 376ba84..74d33a0 100644
--- a/include/linux/mfd/da9062/core.h
+++ b/include/linux/mfd/da9062/core.h
@@ -1,5 +1,5 @@
/*
- * Copyright (C) 2015 Dialog Semiconductor Ltd.
+ * Copyright (C) 2015-2017 Dialog Semiconductor
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
@@ -18,7 +18,31 @@
#include <linux/interrupt.h>
#include <linux/mfd/da9062/registers.h>
-/* Interrupts */
+enum da9062_compatible_types {
+ COMPAT_TYPE_DA9061 = 1,
+ COMPAT_TYPE_DA9062,
+};
+
+enum da9061_irqs {
+ /* IRQ A */
+ DA9061_IRQ_ONKEY,
+ DA9061_IRQ_WDG_WARN,
+ DA9061_IRQ_SEQ_RDY,
+ /* IRQ B*/
+ DA9061_IRQ_TEMP,
+ DA9061_IRQ_LDO_LIM,
+ DA9061_IRQ_DVC_RDY,
+ DA9061_IRQ_VDD_WARN,
+ /* IRQ C */
+ DA9061_IRQ_GPI0,
+ DA9061_IRQ_GPI1,
+ DA9061_IRQ_GPI2,
+ DA9061_IRQ_GPI3,
+ DA9061_IRQ_GPI4,
+
+ DA9061_NUM_IRQ,
+};
+
enum da9062_irqs {
/* IRQ A */
DA9062_IRQ_ONKEY,
@@ -45,6 +69,7 @@ struct da9062 {
struct device *dev;
struct regmap *regmap;
struct regmap_irq_chip_data *regmap_irq;
+ enum da9062_compatible_types chip_type;
};
#endif /* __MFD_DA9062_CORE_H__ */
diff --git a/include/linux/mfd/da9062/registers.h b/include/linux/mfd/da9062/registers.h
index 97790d1..18d576a 100644
--- a/include/linux/mfd/da9062/registers.h
+++ b/include/linux/mfd/da9062/registers.h
@@ -1,6 +1,5 @@
/*
- * registers.h - REGISTERS H for DA9062
- * Copyright (C) 2015 Dialog Semiconductor Ltd.
+ * Copyright (C) 2015-2017 Dialog Semiconductor
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
@@ -18,6 +17,8 @@
#define DA9062_PMIC_DEVICE_ID 0x62
#define DA9062_PMIC_VARIANT_MRC_AA 0x01
+#define DA9062_PMIC_VARIANT_VRC_DA9061 0x01
+#define DA9062_PMIC_VARIANT_VRC_DA9062 0x02
#define DA9062_I2C_PAGE_SEL_SHIFT 1
--
end-of-patch for PATCH V7
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 36+ messages in thread* Re: [PATCH V7 4/7] mfd: da9061: MFD core support
@ 2017-04-03 14:12 ` Lee Jones
0 siblings, 0 replies; 36+ messages in thread
From: Lee Jones @ 2017-04-03 14:12 UTC (permalink / raw)
To: Steve Twiss
Cc: LINUX-KERNEL, DEVICETREE, Dmitry Torokhov, Eduardo Valentin,
Guenter Roeck, LINUX-INPUT, LINUX-PM, LINUX-WATCHDOG,
Liam Girdwood, Mark Brown, Mark Rutland, Rob Herring,
Support Opensource, Wim Van Sebroeck, Zhang Rui
On Tue, 28 Mar 2017, Steve Twiss wrote:
> From: Steve Twiss <stwiss.opensource@diasemi.com>
>
> MFD support for DA9061 is provided as part of the DA9062 device driver.
>
> The registers header file adds two new chip variant IDs defined in DA9061
> and DA9062 hardware. The core header file adds new software enumerations
> for listing the valid DA9061 IRQs and a da9062_compatible_types enumeration
> for distinguishing between DA9061/62 devices in software.
>
> The core source code adds a new .compatible of_device_id entry. This is
> extended from DA9062 to support both "dlg,da9061" and "dlg,da9062". The
> .data entry now holds a reference to the enumerated device type.
>
> A new regmap_irq_chip model is added for DA9061 and this supports the new
> list of regmap_irq entries. A new mfd_cell da9061_devs[] array lists the
> new sub system components for DA9061. Support is added for a new DA9061
> regmap_config which lists the correct readable, writable and volatile
> ranges for this chip.
>
> The probe function uses the device tree compatible string to switch on the
> da9062_compatible_types and configure the correct mfd cells, irq chip and
> regmap config.
>
> Kconfig is updated to reflect support for DA9061 and DA9062 PMICs.
>
> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
>
> ---
> Acked-for-mfd-by: Lee Jones <lee.jones@linaro.org>
>
> Hi Lee, that Ack was from your earlier posting:
> https://lkml.org/lkml/2017/1/4/328 this was
> Regards, Steve.
>
> This patch applies against linux-next and v4.11-rc3
>
> v6 -> v7
> - Remove compilation warning when casting a void * to an integer on
> ARCH=x86_64 using -Wpointer-to-int-cast.
> - Recommendation uintptr_t cast: https://lkml.org/lkml/2017/3/28/292
> - Compile tested ARCH=x86_64
>
> v5 -> v6
> - Rebased from v4.9 to v4.11-rc3
> - Modify Copyright to match Dialog latest legal statement
> - Fixed "braces {} should be used on all arms" checkpatch warning
>
> v4 -> v5
> - NO CODE CHANGE
> - Rebased from v4.8 to v4.9
>
> v3 -> v4
> - Patch renamed from [PATCH V3 5/9] to [PATCH V4 4/8]
> - Removed DEFINE_RES_NAMED() macros for DA9061 resources and replaced
> them with DEFINE_RES_IRQ_NAMED().
> - Removed whitespace
> - Reverted change for badly defined mfd_cell da9062_devs of_compatible
> string from "dlg,da9062-watchdog" back to "dlg,da9062-wdt"
>
> v2 -> v3
> - NO CODE CHANGE
> - Patch renamed from [PATCH V2 05/10] to [PATCH V3 5/9]
>
> v1 -> v2
> - Patch renamed from [PATCH V1 01/10] to [PATCH V2 05/10] -- these
> changes were made to fix checkpatch warnings caused by the patch
> set dependency order
> - Fixed typo in the commit message "readble" to "readable"
> - Removed the explicit cross-check to decide if there is a conflict
> between the device tree compatible string and the hardware definition.
> This patch assumes the device tree is correctly written and therefore
> removes the need for a hardware/DT sanity check.
> - Removed extra semicolon in drivers/mfd/da9062-core.c:877
> - Re-write compatible entries into numerical order
>
> Lee,
>
> Changes as described in the version history above.
>
> As previously:
> This patch adds support for the DA9061 PMIC. This is done as part of the
> existing DA9062 device driver by extending the of_device_id match table.
> This in turn allows new MFD cells, irq chip and regmap definitions to
> support DA9061.
>
> Regards,
> Steve Twiss, Dialog Semiconductor
>
>
> drivers/mfd/Kconfig | 5 +-
> drivers/mfd/da9062-core.c | 427 +++++++++++++++++++++++++++++++++--
> include/linux/mfd/da9062/core.h | 29 ++-
> include/linux/mfd/da9062/registers.h | 5 +-
> 4 files changed, 443 insertions(+), 23 deletions(-)
>
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index 55ecdfb..29cc11a 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -263,13 +263,14 @@ config MFD_DA9055
> called "da9055"
>
> config MFD_DA9062
> - tristate "Dialog Semiconductor DA9062 PMIC Support"
> + tristate "Dialog Semiconductor DA9062/61 PMIC Support"
> select MFD_CORE
> select REGMAP_I2C
> select REGMAP_IRQ
> depends on I2C
> help
> - Say yes here for support for the Dialog Semiconductor DA9062 PMIC.
> + Say yes here for support for the Dialog Semiconductor DA9061 and
> + DA9062 PMICs.
> This includes the I2C driver and core APIs.
> Additional drivers must be enabled in order to use the functionality
> of the device.
> diff --git a/drivers/mfd/da9062-core.c b/drivers/mfd/da9062-core.c
> index 8f873866..78ab3f4 100644
> --- a/drivers/mfd/da9062-core.c
> +++ b/drivers/mfd/da9062-core.c
[...]
> @@ -475,7 +855,25 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
> return -EINVAL;
> }
>
> - chip->regmap = devm_regmap_init_i2c(i2c, &da9062_regmap_config);
> + switch (chip->chip_type) {
> + case(COMPAT_TYPE_DA9061):
Brackets around the case value?
That's a new one on me.
> + cell = da9061_devs;
> + cell_num = ARRAY_SIZE(da9061_devs);
> + irq_chip = &da9061_irq_chip;
> + config = &da9061_regmap_config;
> + break;
> + case(COMPAT_TYPE_DA9062):
> + cell = da9062_devs;
> + cell_num = ARRAY_SIZE(da9062_devs);
> + irq_chip = &da9062_irq_chip;
> + config = &da9062_regmap_config;
> + break;
> + default:
> + dev_err(chip->dev, "Unrecognised chip type\n");
> + return -ENODEV;
> + }
> +
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 36+ messages in thread* Re: [PATCH V7 4/7] mfd: da9061: MFD core support
@ 2017-04-03 14:12 ` Lee Jones
0 siblings, 0 replies; 36+ messages in thread
From: Lee Jones @ 2017-04-03 14:12 UTC (permalink / raw)
To: Steve Twiss
Cc: LINUX-KERNEL, DEVICETREE, Dmitry Torokhov, Eduardo Valentin,
Guenter Roeck, LINUX-INPUT, LINUX-PM, LINUX-WATCHDOG,
Liam Girdwood, Mark Brown, Mark Rutland, Rob Herring,
Support Opensource, Wim Van Sebroeck, Zhang Rui
On Tue, 28 Mar 2017, Steve Twiss wrote:
> From: Steve Twiss <stwiss.opensource@diasemi.com>
>
> MFD support for DA9061 is provided as part of the DA9062 device driver.
>
> The registers header file adds two new chip variant IDs defined in DA9061
> and DA9062 hardware. The core header file adds new software enumerations
> for listing the valid DA9061 IRQs and a da9062_compatible_types enumeration
> for distinguishing between DA9061/62 devices in software.
>
> The core source code adds a new .compatible of_device_id entry. This is
> extended from DA9062 to support both "dlg,da9061" and "dlg,da9062". The
> .data entry now holds a reference to the enumerated device type.
>
> A new regmap_irq_chip model is added for DA9061 and this supports the new
> list of regmap_irq entries. A new mfd_cell da9061_devs[] array lists the
> new sub system components for DA9061. Support is added for a new DA9061
> regmap_config which lists the correct readable, writable and volatile
> ranges for this chip.
>
> The probe function uses the device tree compatible string to switch on the
> da9062_compatible_types and configure the correct mfd cells, irq chip and
> regmap config.
>
> Kconfig is updated to reflect support for DA9061 and DA9062 PMICs.
>
> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
>
> ---
> Acked-for-mfd-by: Lee Jones <lee.jones@linaro.org>
>
> Hi Lee, that Ack was from your earlier posting:
> https://lkml.org/lkml/2017/1/4/328 this was
> Regards, Steve.
>
> This patch applies against linux-next and v4.11-rc3
>
> v6 -> v7
> - Remove compilation warning when casting a void * to an integer on
> ARCH=x86_64 using -Wpointer-to-int-cast.
> - Recommendation uintptr_t cast: https://lkml.org/lkml/2017/3/28/292
> - Compile tested ARCH=x86_64
>
> v5 -> v6
> - Rebased from v4.9 to v4.11-rc3
> - Modify Copyright to match Dialog latest legal statement
> - Fixed "braces {} should be used on all arms" checkpatch warning
>
> v4 -> v5
> - NO CODE CHANGE
> - Rebased from v4.8 to v4.9
>
> v3 -> v4
> - Patch renamed from [PATCH V3 5/9] to [PATCH V4 4/8]
> - Removed DEFINE_RES_NAMED() macros for DA9061 resources and replaced
> them with DEFINE_RES_IRQ_NAMED().
> - Removed whitespace
> - Reverted change for badly defined mfd_cell da9062_devs of_compatible
> string from "dlg,da9062-watchdog" back to "dlg,da9062-wdt"
>
> v2 -> v3
> - NO CODE CHANGE
> - Patch renamed from [PATCH V2 05/10] to [PATCH V3 5/9]
>
> v1 -> v2
> - Patch renamed from [PATCH V1 01/10] to [PATCH V2 05/10] -- these
> changes were made to fix checkpatch warnings caused by the patch
> set dependency order
> - Fixed typo in the commit message "readble" to "readable"
> - Removed the explicit cross-check to decide if there is a conflict
> between the device tree compatible string and the hardware definition.
> This patch assumes the device tree is correctly written and therefore
> removes the need for a hardware/DT sanity check.
> - Removed extra semicolon in drivers/mfd/da9062-core.c:877
> - Re-write compatible entries into numerical order
>
> Lee,
>
> Changes as described in the version history above.
>
> As previously:
> This patch adds support for the DA9061 PMIC. This is done as part of the
> existing DA9062 device driver by extending the of_device_id match table.
> This in turn allows new MFD cells, irq chip and regmap definitions to
> support DA9061.
>
> Regards,
> Steve Twiss, Dialog Semiconductor
>
>
> drivers/mfd/Kconfig | 5 +-
> drivers/mfd/da9062-core.c | 427 +++++++++++++++++++++++++++++++++--
> include/linux/mfd/da9062/core.h | 29 ++-
> include/linux/mfd/da9062/registers.h | 5 +-
> 4 files changed, 443 insertions(+), 23 deletions(-)
>
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index 55ecdfb..29cc11a 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -263,13 +263,14 @@ config MFD_DA9055
> called "da9055"
>
> config MFD_DA9062
> - tristate "Dialog Semiconductor DA9062 PMIC Support"
> + tristate "Dialog Semiconductor DA9062/61 PMIC Support"
> select MFD_CORE
> select REGMAP_I2C
> select REGMAP_IRQ
> depends on I2C
> help
> - Say yes here for support for the Dialog Semiconductor DA9062 PMIC.
> + Say yes here for support for the Dialog Semiconductor DA9061 and
> + DA9062 PMICs.
> This includes the I2C driver and core APIs.
> Additional drivers must be enabled in order to use the functionality
> of the device.
> diff --git a/drivers/mfd/da9062-core.c b/drivers/mfd/da9062-core.c
> index 8f873866..78ab3f4 100644
> --- a/drivers/mfd/da9062-core.c
> +++ b/drivers/mfd/da9062-core.c
[...]
> @@ -475,7 +855,25 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
> return -EINVAL;
> }
>
> - chip->regmap = devm_regmap_init_i2c(i2c, &da9062_regmap_config);
> + switch (chip->chip_type) {
> + case(COMPAT_TYPE_DA9061):
Brackets around the case value?
That's a new one on me.
> + cell = da9061_devs;
> + cell_num = ARRAY_SIZE(da9061_devs);
> + irq_chip = &da9061_irq_chip;
> + config = &da9061_regmap_config;
> + break;
> + case(COMPAT_TYPE_DA9062):
> + cell = da9062_devs;
> + cell_num = ARRAY_SIZE(da9062_devs);
> + irq_chip = &da9062_irq_chip;
> + config = &da9062_regmap_config;
> + break;
> + default:
> + dev_err(chip->dev, "Unrecognised chip type\n");
> + return -ENODEV;
> + }
> +
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 36+ messages in thread* Re: [PATCH V7 4/7] mfd: da9061: MFD core support
@ 2017-04-03 14:12 ` Lee Jones
0 siblings, 0 replies; 36+ messages in thread
From: Lee Jones @ 2017-04-03 14:12 UTC (permalink / raw)
To: Steve Twiss
Cc: LINUX-KERNEL, DEVICETREE, Dmitry Torokhov, Eduardo Valentin,
Guenter Roeck, LINUX-INPUT, LINUX-PM, LINUX-WATCHDOG,
Liam Girdwood, Mark Brown, Mark Rutland, Rob Herring,
Support Opensource, Wim Van Sebroeck, Zhang Rui
On Tue, 28 Mar 2017, Steve Twiss wrote:
> From: Steve Twiss <stwiss.opensource-WBD+wuPFNBhBDgjK7y7TUQ@public.gmane.org>
>
> MFD support for DA9061 is provided as part of the DA9062 device driver.
>
> The registers header file adds two new chip variant IDs defined in DA9061
> and DA9062 hardware. The core header file adds new software enumerations
> for listing the valid DA9061 IRQs and a da9062_compatible_types enumeration
> for distinguishing between DA9061/62 devices in software.
>
> The core source code adds a new .compatible of_device_id entry. This is
> extended from DA9062 to support both "dlg,da9061" and "dlg,da9062". The
> .data entry now holds a reference to the enumerated device type.
>
> A new regmap_irq_chip model is added for DA9061 and this supports the new
> list of regmap_irq entries. A new mfd_cell da9061_devs[] array lists the
> new sub system components for DA9061. Support is added for a new DA9061
> regmap_config which lists the correct readable, writable and volatile
> ranges for this chip.
>
> The probe function uses the device tree compatible string to switch on the
> da9062_compatible_types and configure the correct mfd cells, irq chip and
> regmap config.
>
> Kconfig is updated to reflect support for DA9061 and DA9062 PMICs.
>
> Signed-off-by: Steve Twiss <stwiss.opensource-WBD+wuPFNBhBDgjK7y7TUQ@public.gmane.org>
>
> ---
> Acked-for-mfd-by: Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
>
> Hi Lee, that Ack was from your earlier posting:
> https://lkml.org/lkml/2017/1/4/328 this was
> Regards, Steve.
>
> This patch applies against linux-next and v4.11-rc3
>
> v6 -> v7
> - Remove compilation warning when casting a void * to an integer on
> ARCH=x86_64 using -Wpointer-to-int-cast.
> - Recommendation uintptr_t cast: https://lkml.org/lkml/2017/3/28/292
> - Compile tested ARCH=x86_64
>
> v5 -> v6
> - Rebased from v4.9 to v4.11-rc3
> - Modify Copyright to match Dialog latest legal statement
> - Fixed "braces {} should be used on all arms" checkpatch warning
>
> v4 -> v5
> - NO CODE CHANGE
> - Rebased from v4.8 to v4.9
>
> v3 -> v4
> - Patch renamed from [PATCH V3 5/9] to [PATCH V4 4/8]
> - Removed DEFINE_RES_NAMED() macros for DA9061 resources and replaced
> them with DEFINE_RES_IRQ_NAMED().
> - Removed whitespace
> - Reverted change for badly defined mfd_cell da9062_devs of_compatible
> string from "dlg,da9062-watchdog" back to "dlg,da9062-wdt"
>
> v2 -> v3
> - NO CODE CHANGE
> - Patch renamed from [PATCH V2 05/10] to [PATCH V3 5/9]
>
> v1 -> v2
> - Patch renamed from [PATCH V1 01/10] to [PATCH V2 05/10] -- these
> changes were made to fix checkpatch warnings caused by the patch
> set dependency order
> - Fixed typo in the commit message "readble" to "readable"
> - Removed the explicit cross-check to decide if there is a conflict
> between the device tree compatible string and the hardware definition.
> This patch assumes the device tree is correctly written and therefore
> removes the need for a hardware/DT sanity check.
> - Removed extra semicolon in drivers/mfd/da9062-core.c:877
> - Re-write compatible entries into numerical order
>
> Lee,
>
> Changes as described in the version history above.
>
> As previously:
> This patch adds support for the DA9061 PMIC. This is done as part of the
> existing DA9062 device driver by extending the of_device_id match table.
> This in turn allows new MFD cells, irq chip and regmap definitions to
> support DA9061.
>
> Regards,
> Steve Twiss, Dialog Semiconductor
>
>
> drivers/mfd/Kconfig | 5 +-
> drivers/mfd/da9062-core.c | 427 +++++++++++++++++++++++++++++++++--
> include/linux/mfd/da9062/core.h | 29 ++-
> include/linux/mfd/da9062/registers.h | 5 +-
> 4 files changed, 443 insertions(+), 23 deletions(-)
>
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index 55ecdfb..29cc11a 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -263,13 +263,14 @@ config MFD_DA9055
> called "da9055"
>
> config MFD_DA9062
> - tristate "Dialog Semiconductor DA9062 PMIC Support"
> + tristate "Dialog Semiconductor DA9062/61 PMIC Support"
> select MFD_CORE
> select REGMAP_I2C
> select REGMAP_IRQ
> depends on I2C
> help
> - Say yes here for support for the Dialog Semiconductor DA9062 PMIC.
> + Say yes here for support for the Dialog Semiconductor DA9061 and
> + DA9062 PMICs.
> This includes the I2C driver and core APIs.
> Additional drivers must be enabled in order to use the functionality
> of the device.
> diff --git a/drivers/mfd/da9062-core.c b/drivers/mfd/da9062-core.c
> index 8f873866..78ab3f4 100644
> --- a/drivers/mfd/da9062-core.c
> +++ b/drivers/mfd/da9062-core.c
[...]
> @@ -475,7 +855,25 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
> return -EINVAL;
> }
>
> - chip->regmap = devm_regmap_init_i2c(i2c, &da9062_regmap_config);
> + switch (chip->chip_type) {
> + case(COMPAT_TYPE_DA9061):
Brackets around the case value?
That's a new one on me.
> + cell = da9061_devs;
> + cell_num = ARRAY_SIZE(da9061_devs);
> + irq_chip = &da9061_irq_chip;
> + config = &da9061_regmap_config;
> + break;
> + case(COMPAT_TYPE_DA9062):
> + cell = da9062_devs;
> + cell_num = ARRAY_SIZE(da9062_devs);
> + irq_chip = &da9062_irq_chip;
> + config = &da9062_regmap_config;
> + break;
> + default:
> + dev_err(chip->dev, "Unrecognised chip type\n");
> + return -ENODEV;
> + }
> +
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 36+ messages in thread* RE: [PATCH V7 4/7] mfd: da9061: MFD core support
2017-04-03 14:12 ` Lee Jones
(?)
(?)
@ 2017-04-03 14:20 ` Steve Twiss
2017-04-03 14:30 ` Lee Jones
-1 siblings, 1 reply; 36+ messages in thread
From: Steve Twiss @ 2017-04-03 14:20 UTC (permalink / raw)
To: Lee Jones
Cc: LINUX-KERNEL, DEVICETREE, Dmitry Torokhov, Eduardo Valentin,
Guenter Roeck, LINUX-INPUT, LINUX-PM, LINUX-WATCHDOG,
Liam Girdwood, Mark Brown, Mark Rutland, Rob Herring,
Support Opensource, Wim Van Sebroeck, Zhang Rui
On 03 April 2017 15:12, Lee Jones wrote:
> > @@ -475,7 +855,25 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
> > return -EINVAL;
> > }
> >
> > - chip->regmap = devm_regmap_init_i2c(i2c, &da9062_regmap_config);
> > + switch (chip->chip_type) {
> > + case(COMPAT_TYPE_DA9061):
>
> Brackets around the case value?
>
> That's a new one on me.
Hm. Do you want me to resend it without braces?
Regards,
Stephen
^ permalink raw reply [flat|nested] 36+ messages in thread* Re: [PATCH V7 4/7] mfd: da9061: MFD core support
2017-04-03 14:20 ` Steve Twiss
@ 2017-04-03 14:30 ` Lee Jones
0 siblings, 0 replies; 36+ messages in thread
From: Lee Jones @ 2017-04-03 14:30 UTC (permalink / raw)
To: Steve Twiss
Cc: LINUX-KERNEL, DEVICETREE, Dmitry Torokhov, Eduardo Valentin,
Guenter Roeck, LINUX-INPUT, LINUX-PM, LINUX-WATCHDOG,
Liam Girdwood, Mark Brown, Mark Rutland, Rob Herring,
Support Opensource, Wim Van Sebroeck, Zhang Rui
On Mon, 03 Apr 2017, Steve Twiss wrote:
> On 03 April 2017 15:12, Lee Jones wrote:
>
> > > @@ -475,7 +855,25 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
> > > return -EINVAL;
> > > }
> > >
> > > - chip->regmap = devm_regmap_init_i2c(i2c, &da9062_regmap_config);
> > > + switch (chip->chip_type) {
> > > + case(COMPAT_TYPE_DA9061):
> >
> > Brackets around the case value?
> >
> > That's a new one on me.
>
> Hm. Do you want me to resend it without braces?
Yes please. And a space after the 'case'.
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 36+ messages in thread* Re: [PATCH V7 4/7] mfd: da9061: MFD core support
@ 2017-04-03 14:30 ` Lee Jones
0 siblings, 0 replies; 36+ messages in thread
From: Lee Jones @ 2017-04-03 14:30 UTC (permalink / raw)
To: Steve Twiss
Cc: LINUX-KERNEL, DEVICETREE, Dmitry Torokhov, Eduardo Valentin,
Guenter Roeck, LINUX-INPUT, LINUX-PM, LINUX-WATCHDOG,
Liam Girdwood, Mark Brown, Mark Rutland, Rob Herring,
Support Opensource, Wim Van Sebroeck, Zhang Rui
On Mon, 03 Apr 2017, Steve Twiss wrote:
> On 03 April 2017 15:12, Lee Jones wrote:
>
> > > @@ -475,7 +855,25 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
> > > return -EINVAL;
> > > }
> > >
> > > - chip->regmap = devm_regmap_init_i2c(i2c, &da9062_regmap_config);
> > > + switch (chip->chip_type) {
> > > + case(COMPAT_TYPE_DA9061):
> >
> > Brackets around the case value?
> >
> > That's a new one on me.
>
> Hm. Do you want me to resend it without braces?
Yes please. And a space after the 'case'.
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 36+ messages in thread* RE: [PATCH V7 4/7] mfd: da9061: MFD core support
2017-04-03 14:30 ` Lee Jones
(?)
@ 2017-04-03 15:56 ` Steve Twiss
2017-04-04 8:34 ` Lee Jones
-1 siblings, 1 reply; 36+ messages in thread
From: Steve Twiss @ 2017-04-03 15:56 UTC (permalink / raw)
To: Lee Jones
Cc: LINUX-KERNEL, DEVICETREE, Dmitry Torokhov, Eduardo Valentin,
Guenter Roeck, LINUX-INPUT, LINUX-PM, LINUX-WATCHDOG,
Liam Girdwood, Mark Brown, Mark Rutland, Rob Herring,
Support Opensource, Wim Van Sebroeck, Zhang Rui
On 03 April 2017 15:31, Lee Jones wrote:
> Subject: Re: [PATCH V7 4/7] mfd: da9061: MFD core support
>
> On Mon, 03 Apr 2017, Steve Twiss wrote:
> > On 03 April 2017 15:12, Lee Jones wrote:
> >
> > > > @@ -475,7 +855,25 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
> > > > return -EINVAL;
> > > > }
> > > >
> > > > - chip->regmap = devm_regmap_init_i2c(i2c, &da9062_regmap_config);
> > > > + switch (chip->chip_type) {
> > > > + case(COMPAT_TYPE_DA9061):
> > >
> > > Brackets around the case value?
> > >
> > > That's a new one on me.
> >
> > Hm. Do you want me to resend it without braces?
>
> Yes please. And a space after the 'case'.
Hi Lee,
I have resent PATCH V7 to change "case(X):" to be "case X:".
- Removed brackets surrounding case statements for
case COMPAT_TYPE_DA9061:
case COMPAT_TYPE_DA9062:
New patch is here:
https://lkml.org/lkml/2017/4/3/462
The patch it is called by the same title "[PATCH V7 4/7] mfd: da9061: MFD core support".
I've not updated the whole patch-set or changed the patch version number from V7.
Regards,
Steve
^ permalink raw reply [flat|nested] 36+ messages in thread* Re: [PATCH V7 4/7] mfd: da9061: MFD core support
@ 2017-04-04 8:34 ` Lee Jones
0 siblings, 0 replies; 36+ messages in thread
From: Lee Jones @ 2017-04-04 8:34 UTC (permalink / raw)
To: Steve Twiss
Cc: LINUX-KERNEL, DEVICETREE, Dmitry Torokhov, Eduardo Valentin,
Guenter Roeck, LINUX-INPUT, LINUX-PM, LINUX-WATCHDOG,
Liam Girdwood, Mark Brown, Mark Rutland, Rob Herring,
Support Opensource, Wim Van Sebroeck, Zhang Rui
On Mon, 03 Apr 2017, Steve Twiss wrote:
> On 03 April 2017 15:31, Lee Jones wrote:
>
> > Subject: Re: [PATCH V7 4/7] mfd: da9061: MFD core support
> >
> > On Mon, 03 Apr 2017, Steve Twiss wrote:
> > > On 03 April 2017 15:12, Lee Jones wrote:
> > >
> > > > > @@ -475,7 +855,25 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
> > > > > return -EINVAL;
> > > > > }
> > > > >
> > > > > - chip->regmap = devm_regmap_init_i2c(i2c, &da9062_regmap_config);
> > > > > + switch (chip->chip_type) {
> > > > > + case(COMPAT_TYPE_DA9061):
> > > >
> > > > Brackets around the case value?
> > > >
> > > > That's a new one on me.
> > >
> > > Hm. Do you want me to resend it without braces?
> >
> > Yes please. And a space after the 'case'.
>
> Hi Lee,
>
> I have resent PATCH V7 to change "case(X):" to be "case X:".
> - Removed brackets surrounding case statements for
> case COMPAT_TYPE_DA9061:
> case COMPAT_TYPE_DA9062:
Okay, good.
> New patch is here:
> https://lkml.org/lkml/2017/4/3/462
>
> The patch it is called by the same title "[PATCH V7 4/7] mfd: da9061: MFD core support".
> I've not updated the whole patch-set or changed the patch version number from V7.
I don't see it in my inbox?
You should always change the version, or things get confusing.
Even if it's a small change, you can differentiate by v7.1 or similar.
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 36+ messages in thread* Re: [PATCH V7 4/7] mfd: da9061: MFD core support
@ 2017-04-04 8:34 ` Lee Jones
0 siblings, 0 replies; 36+ messages in thread
From: Lee Jones @ 2017-04-04 8:34 UTC (permalink / raw)
To: Steve Twiss
Cc: LINUX-KERNEL, DEVICETREE, Dmitry Torokhov, Eduardo Valentin,
Guenter Roeck, LINUX-INPUT, LINUX-PM, LINUX-WATCHDOG,
Liam Girdwood, Mark Brown, Mark Rutland, Rob Herring,
Support Opensource, Wim Van Sebroeck, Zhang Rui
On Mon, 03 Apr 2017, Steve Twiss wrote:
> On 03 April 2017 15:31, Lee Jones wrote:
>
> > Subject: Re: [PATCH V7 4/7] mfd: da9061: MFD core support
> >
> > On Mon, 03 Apr 2017, Steve Twiss wrote:
> > > On 03 April 2017 15:12, Lee Jones wrote:
> > >
> > > > > @@ -475,7 +855,25 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
> > > > > return -EINVAL;
> > > > > }
> > > > >
> > > > > - chip->regmap = devm_regmap_init_i2c(i2c, &da9062_regmap_config);
> > > > > + switch (chip->chip_type) {
> > > > > + case(COMPAT_TYPE_DA9061):
> > > >
> > > > Brackets around the case value?
> > > >
> > > > That's a new one on me.
> > >
> > > Hm. Do you want me to resend it without braces?
> >
> > Yes please. And a space after the 'case'.
>
> Hi Lee,
>
> I have resent PATCH V7 to change "case(X):" to be "case X:".
> - Removed brackets surrounding case statements for
> case COMPAT_TYPE_DA9061:
> case COMPAT_TYPE_DA9062:
Okay, good.
> New patch is here:
> https://lkml.org/lkml/2017/4/3/462
>
> The patch it is called by the same title "[PATCH V7 4/7] mfd: da9061: MFD core support".
> I've not updated the whole patch-set or changed the patch version number from V7.
I don't see it in my inbox?
You should always change the version, or things get confusing.
Even if it's a small change, you can differentiate by v7.1 or similar.
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 36+ messages in thread* Re: [PATCH V7 4/7] mfd: da9061: MFD core support
@ 2017-04-04 8:34 ` Lee Jones
0 siblings, 0 replies; 36+ messages in thread
From: Lee Jones @ 2017-04-04 8:34 UTC (permalink / raw)
To: Steve Twiss
Cc: LINUX-KERNEL, DEVICETREE, Dmitry Torokhov, Eduardo Valentin,
Guenter Roeck, LINUX-INPUT, LINUX-PM, LINUX-WATCHDOG,
Liam Girdwood, Mark Brown, Mark Rutland, Rob Herring,
Support Opensource, Wim Van Sebroeck, Zhang Rui
On Mon, 03 Apr 2017, Steve Twiss wrote:
> On 03 April 2017 15:31, Lee Jones wrote:
>
> > Subject: Re: [PATCH V7 4/7] mfd: da9061: MFD core support
> >
> > On Mon, 03 Apr 2017, Steve Twiss wrote:
> > > On 03 April 2017 15:12, Lee Jones wrote:
> > >
> > > > > @@ -475,7 +855,25 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
> > > > > return -EINVAL;
> > > > > }
> > > > >
> > > > > - chip->regmap = devm_regmap_init_i2c(i2c, &da9062_regmap_config);
> > > > > + switch (chip->chip_type) {
> > > > > + case(COMPAT_TYPE_DA9061):
> > > >
> > > > Brackets around the case value?
> > > >
> > > > That's a new one on me.
> > >
> > > Hm. Do you want me to resend it without braces?
> >
> > Yes please. And a space after the 'case'.
>
> Hi Lee,
>
> I have resent PATCH V7 to change "case(X):" to be "case X:".
> - Removed brackets surrounding case statements for
> case COMPAT_TYPE_DA9061:
> case COMPAT_TYPE_DA9062:
Okay, good.
> New patch is here:
> https://lkml.org/lkml/2017/4/3/462
>
> The patch it is called by the same title "[PATCH V7 4/7] mfd: da9061: MFD core support".
> I've not updated the whole patch-set or changed the patch version number from V7.
I don't see it in my inbox?
You should always change the version, or things get confusing.
Even if it's a small change, you can differentiate by v7.1 or similar.
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH V7 5/7] regulator: da9061: BUCK and LDO regulator driver
@ 2017-03-28 14:43 ` Steve Twiss
0 siblings, 0 replies; 36+ messages in thread
From: Steve Twiss @ 2017-03-28 14:43 UTC (permalink / raw)
To: LINUX-KERNEL, Liam Girdwood, Mark Brown
Cc: DEVICETREE, Dmitry Torokhov, Eduardo Valentin, Guenter Roeck,
LINUX-INPUT, LINUX-PM, LINUX-WATCHDOG, Lee Jones, Mark Rutland,
Rob Herring, Support Opensource, Wim Van Sebroeck, Zhang Rui
From: Steve Twiss <stwiss.opensource@diasemi.com>
Regulator support for the DA9061 is added into the DA9062 regulator driver.
The regulators for DA9061 differ from those of DA9062.
A new DA9061 enumeration list for the LDOs and Bucks supported by this
device is added. Regulator information added: the old regulator
information for DA9062 is renamed from local_regulator_info[] to
local_da9062_regulator_info[] and a new array is added to support
local_da9061_regulator_info[].
The probe() function switches on the da9062_compatible_types enumeration
and configures the correct da9062_regulator_info array and number of
regulator entries.
Kconfig is updated to reflect support for DA9061 and DA9062 regulators.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
---
This patch applies against linux-next and v4.11-rc3
v6 -> v7
- NO CODE CHANGE
- Compile tested ARCH=x86_64
v5 -> v6
- Rebased from v4.9 to v4.11-rc3
- Modify Copyright to match Dialog latest legal statement
v4 -> v5
- Rebased from v4.8 to v4.9
- NO CODE CHANGE
v3 -> v4
- NO CODE CHANGE
- Patch renamed from [PATCH V3 6/9] to [PATCH V4 5/8]
v2 -> v3
- NO CODE CHANGE
- Patch renamed from [PATCH V2 06/10] to [PATCH V3 6/9]
- Added Ack from Mark Brown
v1 -> v2
- Patch renamed from [PATCH V1 02/10] to [PATCH V2 06/10] -- these
changes were made to fix checkpatch warnings caused by the patch
set dependency order
- Updated header to use DA9061 and DA9062
Hi,
Updated copyright header slightly to match Dialog's legal expectation.
No code changes for this version PATCH V5.
As previously:
These changes depend on a header file provided as part of an earlier
patch [PATCH V5 4/8] from this set. The regulator probe() switches on
the chip_type which uses enum da9062_compatible_types in core.h from this
patch.
Regards,
Steve Twiss, Dialog Semiconductor
drivers/regulator/Kconfig | 4 +-
drivers/regulator/da9062-regulator.c | 303 +++++++++++++++++++++++++++++++++--
2 files changed, 293 insertions(+), 14 deletions(-)
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index be06eb2..c2e67f12 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -195,11 +195,11 @@ config REGULATOR_DA9055
will be called da9055-regulator.
config REGULATOR_DA9062
- tristate "Dialog Semiconductor DA9062 regulators"
+ tristate "Dialog Semiconductor DA9061/62 regulators"
depends on MFD_DA9062
help
Say y here to support the BUCKs and LDOs regulators found on
- DA9062 PMICs.
+ DA9061 and DA9062 PMICs.
This driver can also be built as a module. If so, the module
will be called da9062-regulator.
diff --git a/drivers/regulator/da9062-regulator.c b/drivers/regulator/da9062-regulator.c
index 0638c8b..34a70d9 100644
--- a/drivers/regulator/da9062-regulator.c
+++ b/drivers/regulator/da9062-regulator.c
@@ -1,6 +1,6 @@
/*
- * da9062-regulator.c - REGULATOR device driver for DA9062
- * Copyright (C) 2015 Dialog Semiconductor Ltd.
+ * Regulator device driver for DA9061 and DA9062.
+ * Copyright (C) 2015-2017 Dialog Semiconductor
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
@@ -28,6 +28,17 @@
/* Regulator IDs */
enum {
+ DA9061_ID_BUCK1,
+ DA9061_ID_BUCK2,
+ DA9061_ID_BUCK3,
+ DA9061_ID_LDO1,
+ DA9061_ID_LDO2,
+ DA9061_ID_LDO3,
+ DA9061_ID_LDO4,
+ DA9061_MAX_REGULATORS,
+};
+
+enum {
DA9062_ID_BUCK1,
DA9062_ID_BUCK2,
DA9062_ID_BUCK3,
@@ -88,15 +99,21 @@ enum {
/* Regulator operations */
-/* Current limits array (in uA) BUCK1 and BUCK3.
- Entry indexes corresponds to register values. */
+/* Current limits array (in uA)
+ * - DA9061_ID_[BUCK1|BUCK3]
+ * - DA9062_ID_[BUCK1|BUCK2|BUCK4]
+ * Entry indexes corresponds to register values.
+ */
static const int da9062_buck_a_limits[] = {
500000, 600000, 700000, 800000, 900000, 1000000, 1100000, 1200000,
1300000, 1400000, 1500000, 1600000, 1700000, 1800000, 1900000, 2000000
};
-/* Current limits array (in uA) for BUCK2.
- Entry indexes corresponds to register values. */
+/* Current limits array (in uA)
+ * - DA9061_ID_BUCK2
+ * - DA9062_ID_BUCK3
+ * Entry indexes corresponds to register values.
+ */
static const int da9062_buck_b_limits[] = {
1500000, 1600000, 1700000, 1800000, 1900000, 2000000, 2100000, 2200000,
2300000, 2400000, 2500000, 2600000, 2700000, 2800000, 2900000, 3000000
@@ -405,8 +422,254 @@ static int da9062_ldo_set_suspend_mode(struct regulator_dev *rdev,
.set_suspend_mode = da9062_ldo_set_suspend_mode,
};
-/* Regulator information */
-static const struct da9062_regulator_info local_regulator_info[] = {
+/* DA9061 Regulator information */
+static const struct da9062_regulator_info local_da9061_regulator_info[] = {
+ {
+ .desc.id = DA9061_ID_BUCK1,
+ .desc.name = "DA9061 BUCK1",
+ .desc.of_match = of_match_ptr("buck1"),
+ .desc.regulators_node = of_match_ptr("regulators"),
+ .desc.ops = &da9062_buck_ops,
+ .desc.min_uV = (300) * 1000,
+ .desc.uV_step = (10) * 1000,
+ .desc.n_voltages = ((1570) - (300))/(10) + 1,
+ .current_limits = da9062_buck_a_limits,
+ .n_current_limits = ARRAY_SIZE(da9062_buck_a_limits),
+ .desc.enable_reg = DA9062AA_BUCK1_CONT,
+ .desc.enable_mask = DA9062AA_BUCK1_EN_MASK,
+ .desc.vsel_reg = DA9062AA_VBUCK1_A,
+ .desc.vsel_mask = DA9062AA_VBUCK1_A_MASK,
+ .desc.linear_min_sel = 0,
+ .sleep = REG_FIELD(DA9062AA_VBUCK1_A,
+ __builtin_ffs((int)DA9062AA_BUCK1_SL_A_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK1_SL_A_MASK)) - 1),
+ .suspend_sleep = REG_FIELD(DA9062AA_VBUCK1_B,
+ __builtin_ffs((int)DA9062AA_BUCK1_SL_B_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK1_SL_B_MASK)) - 1),
+ .suspend_vsel_reg = DA9062AA_VBUCK1_B,
+ .mode = REG_FIELD(DA9062AA_BUCK1_CFG,
+ __builtin_ffs((int)DA9062AA_BUCK1_MODE_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK1_MODE_MASK)) - 1),
+ .suspend = REG_FIELD(DA9062AA_DVC_1,
+ __builtin_ffs((int)DA9062AA_VBUCK1_SEL_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_VBUCK1_SEL_MASK)) - 1),
+ .ilimit = REG_FIELD(DA9062AA_BUCK_ILIM_C,
+ __builtin_ffs((int)DA9062AA_BUCK1_ILIM_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK1_ILIM_MASK)) - 1),
+ },
+ {
+ .desc.id = DA9061_ID_BUCK2,
+ .desc.name = "DA9061 BUCK2",
+ .desc.of_match = of_match_ptr("buck2"),
+ .desc.regulators_node = of_match_ptr("regulators"),
+ .desc.ops = &da9062_buck_ops,
+ .desc.min_uV = (800) * 1000,
+ .desc.uV_step = (20) * 1000,
+ .desc.n_voltages = ((3340) - (800))/(20) + 1,
+ .current_limits = da9062_buck_b_limits,
+ .n_current_limits = ARRAY_SIZE(da9062_buck_b_limits),
+ .desc.enable_reg = DA9062AA_BUCK3_CONT,
+ .desc.enable_mask = DA9062AA_BUCK3_EN_MASK,
+ .desc.vsel_reg = DA9062AA_VBUCK3_A,
+ .desc.vsel_mask = DA9062AA_VBUCK3_A_MASK,
+ .desc.linear_min_sel = 0,
+ .sleep = REG_FIELD(DA9062AA_VBUCK3_A,
+ __builtin_ffs((int)DA9062AA_BUCK3_SL_A_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK3_SL_A_MASK)) - 1),
+ .suspend_sleep = REG_FIELD(DA9062AA_VBUCK3_B,
+ __builtin_ffs((int)DA9062AA_BUCK3_SL_B_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK3_SL_B_MASK)) - 1),
+ .suspend_vsel_reg = DA9062AA_VBUCK3_B,
+ .mode = REG_FIELD(DA9062AA_BUCK3_CFG,
+ __builtin_ffs((int)DA9062AA_BUCK3_MODE_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK3_MODE_MASK)) - 1),
+ .suspend = REG_FIELD(DA9062AA_DVC_1,
+ __builtin_ffs((int)DA9062AA_VBUCK3_SEL_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_VBUCK3_SEL_MASK)) - 1),
+ .ilimit = REG_FIELD(DA9062AA_BUCK_ILIM_A,
+ __builtin_ffs((int)DA9062AA_BUCK3_ILIM_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK3_ILIM_MASK)) - 1),
+ },
+ {
+ .desc.id = DA9061_ID_BUCK3,
+ .desc.name = "DA9061 BUCK3",
+ .desc.of_match = of_match_ptr("buck3"),
+ .desc.regulators_node = of_match_ptr("regulators"),
+ .desc.ops = &da9062_buck_ops,
+ .desc.min_uV = (530) * 1000,
+ .desc.uV_step = (10) * 1000,
+ .desc.n_voltages = ((1800) - (530))/(10) + 1,
+ .current_limits = da9062_buck_a_limits,
+ .n_current_limits = ARRAY_SIZE(da9062_buck_a_limits),
+ .desc.enable_reg = DA9062AA_BUCK4_CONT,
+ .desc.enable_mask = DA9062AA_BUCK4_EN_MASK,
+ .desc.vsel_reg = DA9062AA_VBUCK4_A,
+ .desc.vsel_mask = DA9062AA_VBUCK4_A_MASK,
+ .desc.linear_min_sel = 0,
+ .sleep = REG_FIELD(DA9062AA_VBUCK4_A,
+ __builtin_ffs((int)DA9062AA_BUCK4_SL_A_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK4_SL_A_MASK)) - 1),
+ .suspend_sleep = REG_FIELD(DA9062AA_VBUCK4_B,
+ __builtin_ffs((int)DA9062AA_BUCK4_SL_B_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK4_SL_B_MASK)) - 1),
+ .suspend_vsel_reg = DA9062AA_VBUCK4_B,
+ .mode = REG_FIELD(DA9062AA_BUCK4_CFG,
+ __builtin_ffs((int)DA9062AA_BUCK4_MODE_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK4_MODE_MASK)) - 1),
+ .suspend = REG_FIELD(DA9062AA_DVC_1,
+ __builtin_ffs((int)DA9062AA_VBUCK4_SEL_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_VBUCK4_SEL_MASK)) - 1),
+ .ilimit = REG_FIELD(DA9062AA_BUCK_ILIM_B,
+ __builtin_ffs((int)DA9062AA_BUCK4_ILIM_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK4_ILIM_MASK)) - 1),
+ },
+ {
+ .desc.id = DA9061_ID_LDO1,
+ .desc.name = "DA9061 LDO1",
+ .desc.of_match = of_match_ptr("ldo1"),
+ .desc.regulators_node = of_match_ptr("regulators"),
+ .desc.ops = &da9062_ldo_ops,
+ .desc.min_uV = (900) * 1000,
+ .desc.uV_step = (50) * 1000,
+ .desc.n_voltages = ((3600) - (900))/(50) + 1,
+ .desc.enable_reg = DA9062AA_LDO1_CONT,
+ .desc.enable_mask = DA9062AA_LDO1_EN_MASK,
+ .desc.vsel_reg = DA9062AA_VLDO1_A,
+ .desc.vsel_mask = DA9062AA_VLDO1_A_MASK,
+ .desc.linear_min_sel = 0,
+ .sleep = REG_FIELD(DA9062AA_VLDO1_A,
+ __builtin_ffs((int)DA9062AA_LDO1_SL_A_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO1_SL_A_MASK)) - 1),
+ .suspend_sleep = REG_FIELD(DA9062AA_VLDO1_B,
+ __builtin_ffs((int)DA9062AA_LDO1_SL_B_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO1_SL_B_MASK)) - 1),
+ .suspend_vsel_reg = DA9062AA_VLDO1_B,
+ .suspend = REG_FIELD(DA9062AA_DVC_1,
+ __builtin_ffs((int)DA9062AA_VLDO1_SEL_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_VLDO1_SEL_MASK)) - 1),
+ .oc_event = REG_FIELD(DA9062AA_STATUS_D,
+ __builtin_ffs((int)DA9062AA_LDO1_ILIM_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO1_ILIM_MASK)) - 1),
+ },
+ {
+ .desc.id = DA9061_ID_LDO2,
+ .desc.name = "DA9061 LDO2",
+ .desc.of_match = of_match_ptr("ldo2"),
+ .desc.regulators_node = of_match_ptr("regulators"),
+ .desc.ops = &da9062_ldo_ops,
+ .desc.min_uV = (900) * 1000,
+ .desc.uV_step = (50) * 1000,
+ .desc.n_voltages = ((3600) - (600))/(50) + 1,
+ .desc.enable_reg = DA9062AA_LDO2_CONT,
+ .desc.enable_mask = DA9062AA_LDO2_EN_MASK,
+ .desc.vsel_reg = DA9062AA_VLDO2_A,
+ .desc.vsel_mask = DA9062AA_VLDO2_A_MASK,
+ .desc.linear_min_sel = 0,
+ .sleep = REG_FIELD(DA9062AA_VLDO2_A,
+ __builtin_ffs((int)DA9062AA_LDO2_SL_A_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO2_SL_A_MASK)) - 1),
+ .suspend_sleep = REG_FIELD(DA9062AA_VLDO2_B,
+ __builtin_ffs((int)DA9062AA_LDO2_SL_B_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO2_SL_B_MASK)) - 1),
+ .suspend_vsel_reg = DA9062AA_VLDO2_B,
+ .suspend = REG_FIELD(DA9062AA_DVC_1,
+ __builtin_ffs((int)DA9062AA_VLDO2_SEL_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_VLDO2_SEL_MASK)) - 1),
+ .oc_event = REG_FIELD(DA9062AA_STATUS_D,
+ __builtin_ffs((int)DA9062AA_LDO2_ILIM_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO2_ILIM_MASK)) - 1),
+ },
+ {
+ .desc.id = DA9061_ID_LDO3,
+ .desc.name = "DA9061 LDO3",
+ .desc.of_match = of_match_ptr("ldo3"),
+ .desc.regulators_node = of_match_ptr("regulators"),
+ .desc.ops = &da9062_ldo_ops,
+ .desc.min_uV = (900) * 1000,
+ .desc.uV_step = (50) * 1000,
+ .desc.n_voltages = ((3600) - (900))/(50) + 1,
+ .desc.enable_reg = DA9062AA_LDO3_CONT,
+ .desc.enable_mask = DA9062AA_LDO3_EN_MASK,
+ .desc.vsel_reg = DA9062AA_VLDO3_A,
+ .desc.vsel_mask = DA9062AA_VLDO3_A_MASK,
+ .desc.linear_min_sel = 0,
+ .sleep = REG_FIELD(DA9062AA_VLDO3_A,
+ __builtin_ffs((int)DA9062AA_LDO3_SL_A_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO3_SL_A_MASK)) - 1),
+ .suspend_sleep = REG_FIELD(DA9062AA_VLDO3_B,
+ __builtin_ffs((int)DA9062AA_LDO3_SL_B_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO3_SL_B_MASK)) - 1),
+ .suspend_vsel_reg = DA9062AA_VLDO3_B,
+ .suspend = REG_FIELD(DA9062AA_DVC_1,
+ __builtin_ffs((int)DA9062AA_VLDO3_SEL_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_VLDO3_SEL_MASK)) - 1),
+ .oc_event = REG_FIELD(DA9062AA_STATUS_D,
+ __builtin_ffs((int)DA9062AA_LDO3_ILIM_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO3_ILIM_MASK)) - 1),
+ },
+ {
+ .desc.id = DA9061_ID_LDO4,
+ .desc.name = "DA9061 LDO4",
+ .desc.of_match = of_match_ptr("ldo4"),
+ .desc.regulators_node = of_match_ptr("regulators"),
+ .desc.ops = &da9062_ldo_ops,
+ .desc.min_uV = (900) * 1000,
+ .desc.uV_step = (50) * 1000,
+ .desc.n_voltages = ((3600) - (900))/(50) + 1,
+ .desc.enable_reg = DA9062AA_LDO4_CONT,
+ .desc.enable_mask = DA9062AA_LDO4_EN_MASK,
+ .desc.vsel_reg = DA9062AA_VLDO4_A,
+ .desc.vsel_mask = DA9062AA_VLDO4_A_MASK,
+ .desc.linear_min_sel = 0,
+ .sleep = REG_FIELD(DA9062AA_VLDO4_A,
+ __builtin_ffs((int)DA9062AA_LDO4_SL_A_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO4_SL_A_MASK)) - 1),
+ .suspend_sleep = REG_FIELD(DA9062AA_VLDO4_B,
+ __builtin_ffs((int)DA9062AA_LDO4_SL_B_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO4_SL_B_MASK)) - 1),
+ .suspend_vsel_reg = DA9062AA_VLDO4_B,
+ .suspend = REG_FIELD(DA9062AA_DVC_1,
+ __builtin_ffs((int)DA9062AA_VLDO4_SEL_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_VLDO4_SEL_MASK)) - 1),
+ .oc_event = REG_FIELD(DA9062AA_STATUS_D,
+ __builtin_ffs((int)DA9062AA_LDO4_ILIM_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO4_ILIM_MASK)) - 1),
+ },
+};
+
+/* DA9062 Regulator information */
+static const struct da9062_regulator_info local_da9062_regulator_info[] = {
{
.desc.id = DA9062_ID_BUCK1,
.desc.name = "DA9062 BUCK1",
@@ -727,17 +990,33 @@ static int da9062_regulator_probe(struct platform_device *pdev)
struct da9062_regulators *regulators;
struct da9062_regulator *regl;
struct regulator_config config = { };
+ const struct da9062_regulator_info *rinfo;
int irq, n, ret;
size_t size;
+ int max_regulators;
+
+ switch (chip->chip_type) {
+ case COMPAT_TYPE_DA9061:
+ max_regulators = DA9061_MAX_REGULATORS;
+ rinfo = local_da9061_regulator_info;
+ break;
+ case COMPAT_TYPE_DA9062:
+ max_regulators = DA9062_MAX_REGULATORS;
+ rinfo = local_da9062_regulator_info;
+ break;
+ default:
+ dev_err(chip->dev, "Unrecognised chip type\n");
+ return -ENODEV;
+ }
/* Allocate memory required by usable regulators */
size = sizeof(struct da9062_regulators) +
- DA9062_MAX_REGULATORS * sizeof(struct da9062_regulator);
+ max_regulators * sizeof(struct da9062_regulator);
regulators = devm_kzalloc(&pdev->dev, size, GFP_KERNEL);
if (!regulators)
return -ENOMEM;
- regulators->n_regulators = DA9062_MAX_REGULATORS;
+ regulators->n_regulators = max_regulators;
platform_set_drvdata(pdev, regulators);
n = 0;
@@ -745,7 +1024,7 @@ static int da9062_regulator_probe(struct platform_device *pdev)
/* Initialise regulator structure */
regl = ®ulators->regulator[n];
regl->hw = chip;
- regl->info = &local_regulator_info[n];
+ regl->info = &rinfo[n];
regl->desc = regl->info->desc;
regl->desc.type = REGULATOR_VOLTAGE;
regl->desc.owner = THIS_MODULE;
@@ -836,6 +1115,6 @@ static void __exit da9062_regulator_cleanup(void)
/* Module information */
MODULE_AUTHOR("S Twiss <stwiss.opensource@diasemi.com>");
-MODULE_DESCRIPTION("REGULATOR device driver for Dialog DA9062");
+MODULE_DESCRIPTION("REGULATOR device driver for Dialog DA9062 and DA9061");
MODULE_LICENSE("GPL");
MODULE_ALIAS("platform:da9062-regulators");
--
end-of-patch for PATCH V7
^ permalink raw reply related [flat|nested] 36+ messages in thread* [PATCH V7 5/7] regulator: da9061: BUCK and LDO regulator driver
@ 2017-03-28 14:43 ` Steve Twiss
0 siblings, 0 replies; 36+ messages in thread
From: Steve Twiss @ 2017-03-28 14:43 UTC (permalink / raw)
To: LINUX-KERNEL, Liam Girdwood, Mark Brown
Cc: DEVICETREE, Dmitry Torokhov, Eduardo Valentin, Guenter Roeck,
LINUX-INPUT, LINUX-PM, LINUX-WATCHDOG, Lee Jones, Mark Rutland,
Rob Herring, Support Opensource, Wim Van Sebroeck, Zhang Rui
From: Steve Twiss <stwiss.opensource-WBD+wuPFNBhBDgjK7y7TUQ@public.gmane.org>
Regulator support for the DA9061 is added into the DA9062 regulator driver.
The regulators for DA9061 differ from those of DA9062.
A new DA9061 enumeration list for the LDOs and Bucks supported by this
device is added. Regulator information added: the old regulator
information for DA9062 is renamed from local_regulator_info[] to
local_da9062_regulator_info[] and a new array is added to support
local_da9061_regulator_info[].
The probe() function switches on the da9062_compatible_types enumeration
and configures the correct da9062_regulator_info array and number of
regulator entries.
Kconfig is updated to reflect support for DA9061 and DA9062 regulators.
Acked-by: Mark Brown <broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Signed-off-by: Steve Twiss <stwiss.opensource-WBD+wuPFNBhBDgjK7y7TUQ@public.gmane.org>
---
This patch applies against linux-next and v4.11-rc3
v6 -> v7
- NO CODE CHANGE
- Compile tested ARCH=x86_64
v5 -> v6
- Rebased from v4.9 to v4.11-rc3
- Modify Copyright to match Dialog latest legal statement
v4 -> v5
- Rebased from v4.8 to v4.9
- NO CODE CHANGE
v3 -> v4
- NO CODE CHANGE
- Patch renamed from [PATCH V3 6/9] to [PATCH V4 5/8]
v2 -> v3
- NO CODE CHANGE
- Patch renamed from [PATCH V2 06/10] to [PATCH V3 6/9]
- Added Ack from Mark Brown
v1 -> v2
- Patch renamed from [PATCH V1 02/10] to [PATCH V2 06/10] -- these
changes were made to fix checkpatch warnings caused by the patch
set dependency order
- Updated header to use DA9061 and DA9062
Hi,
Updated copyright header slightly to match Dialog's legal expectation.
No code changes for this version PATCH V5.
As previously:
These changes depend on a header file provided as part of an earlier
patch [PATCH V5 4/8] from this set. The regulator probe() switches on
the chip_type which uses enum da9062_compatible_types in core.h from this
patch.
Regards,
Steve Twiss, Dialog Semiconductor
drivers/regulator/Kconfig | 4 +-
drivers/regulator/da9062-regulator.c | 303 +++++++++++++++++++++++++++++++++--
2 files changed, 293 insertions(+), 14 deletions(-)
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index be06eb2..c2e67f12 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -195,11 +195,11 @@ config REGULATOR_DA9055
will be called da9055-regulator.
config REGULATOR_DA9062
- tristate "Dialog Semiconductor DA9062 regulators"
+ tristate "Dialog Semiconductor DA9061/62 regulators"
depends on MFD_DA9062
help
Say y here to support the BUCKs and LDOs regulators found on
- DA9062 PMICs.
+ DA9061 and DA9062 PMICs.
This driver can also be built as a module. If so, the module
will be called da9062-regulator.
diff --git a/drivers/regulator/da9062-regulator.c b/drivers/regulator/da9062-regulator.c
index 0638c8b..34a70d9 100644
--- a/drivers/regulator/da9062-regulator.c
+++ b/drivers/regulator/da9062-regulator.c
@@ -1,6 +1,6 @@
/*
- * da9062-regulator.c - REGULATOR device driver for DA9062
- * Copyright (C) 2015 Dialog Semiconductor Ltd.
+ * Regulator device driver for DA9061 and DA9062.
+ * Copyright (C) 2015-2017 Dialog Semiconductor
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
@@ -28,6 +28,17 @@
/* Regulator IDs */
enum {
+ DA9061_ID_BUCK1,
+ DA9061_ID_BUCK2,
+ DA9061_ID_BUCK3,
+ DA9061_ID_LDO1,
+ DA9061_ID_LDO2,
+ DA9061_ID_LDO3,
+ DA9061_ID_LDO4,
+ DA9061_MAX_REGULATORS,
+};
+
+enum {
DA9062_ID_BUCK1,
DA9062_ID_BUCK2,
DA9062_ID_BUCK3,
@@ -88,15 +99,21 @@ enum {
/* Regulator operations */
-/* Current limits array (in uA) BUCK1 and BUCK3.
- Entry indexes corresponds to register values. */
+/* Current limits array (in uA)
+ * - DA9061_ID_[BUCK1|BUCK3]
+ * - DA9062_ID_[BUCK1|BUCK2|BUCK4]
+ * Entry indexes corresponds to register values.
+ */
static const int da9062_buck_a_limits[] = {
500000, 600000, 700000, 800000, 900000, 1000000, 1100000, 1200000,
1300000, 1400000, 1500000, 1600000, 1700000, 1800000, 1900000, 2000000
};
-/* Current limits array (in uA) for BUCK2.
- Entry indexes corresponds to register values. */
+/* Current limits array (in uA)
+ * - DA9061_ID_BUCK2
+ * - DA9062_ID_BUCK3
+ * Entry indexes corresponds to register values.
+ */
static const int da9062_buck_b_limits[] = {
1500000, 1600000, 1700000, 1800000, 1900000, 2000000, 2100000, 2200000,
2300000, 2400000, 2500000, 2600000, 2700000, 2800000, 2900000, 3000000
@@ -405,8 +422,254 @@ static int da9062_ldo_set_suspend_mode(struct regulator_dev *rdev,
.set_suspend_mode = da9062_ldo_set_suspend_mode,
};
-/* Regulator information */
-static const struct da9062_regulator_info local_regulator_info[] = {
+/* DA9061 Regulator information */
+static const struct da9062_regulator_info local_da9061_regulator_info[] = {
+ {
+ .desc.id = DA9061_ID_BUCK1,
+ .desc.name = "DA9061 BUCK1",
+ .desc.of_match = of_match_ptr("buck1"),
+ .desc.regulators_node = of_match_ptr("regulators"),
+ .desc.ops = &da9062_buck_ops,
+ .desc.min_uV = (300) * 1000,
+ .desc.uV_step = (10) * 1000,
+ .desc.n_voltages = ((1570) - (300))/(10) + 1,
+ .current_limits = da9062_buck_a_limits,
+ .n_current_limits = ARRAY_SIZE(da9062_buck_a_limits),
+ .desc.enable_reg = DA9062AA_BUCK1_CONT,
+ .desc.enable_mask = DA9062AA_BUCK1_EN_MASK,
+ .desc.vsel_reg = DA9062AA_VBUCK1_A,
+ .desc.vsel_mask = DA9062AA_VBUCK1_A_MASK,
+ .desc.linear_min_sel = 0,
+ .sleep = REG_FIELD(DA9062AA_VBUCK1_A,
+ __builtin_ffs((int)DA9062AA_BUCK1_SL_A_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK1_SL_A_MASK)) - 1),
+ .suspend_sleep = REG_FIELD(DA9062AA_VBUCK1_B,
+ __builtin_ffs((int)DA9062AA_BUCK1_SL_B_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK1_SL_B_MASK)) - 1),
+ .suspend_vsel_reg = DA9062AA_VBUCK1_B,
+ .mode = REG_FIELD(DA9062AA_BUCK1_CFG,
+ __builtin_ffs((int)DA9062AA_BUCK1_MODE_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK1_MODE_MASK)) - 1),
+ .suspend = REG_FIELD(DA9062AA_DVC_1,
+ __builtin_ffs((int)DA9062AA_VBUCK1_SEL_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_VBUCK1_SEL_MASK)) - 1),
+ .ilimit = REG_FIELD(DA9062AA_BUCK_ILIM_C,
+ __builtin_ffs((int)DA9062AA_BUCK1_ILIM_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK1_ILIM_MASK)) - 1),
+ },
+ {
+ .desc.id = DA9061_ID_BUCK2,
+ .desc.name = "DA9061 BUCK2",
+ .desc.of_match = of_match_ptr("buck2"),
+ .desc.regulators_node = of_match_ptr("regulators"),
+ .desc.ops = &da9062_buck_ops,
+ .desc.min_uV = (800) * 1000,
+ .desc.uV_step = (20) * 1000,
+ .desc.n_voltages = ((3340) - (800))/(20) + 1,
+ .current_limits = da9062_buck_b_limits,
+ .n_current_limits = ARRAY_SIZE(da9062_buck_b_limits),
+ .desc.enable_reg = DA9062AA_BUCK3_CONT,
+ .desc.enable_mask = DA9062AA_BUCK3_EN_MASK,
+ .desc.vsel_reg = DA9062AA_VBUCK3_A,
+ .desc.vsel_mask = DA9062AA_VBUCK3_A_MASK,
+ .desc.linear_min_sel = 0,
+ .sleep = REG_FIELD(DA9062AA_VBUCK3_A,
+ __builtin_ffs((int)DA9062AA_BUCK3_SL_A_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK3_SL_A_MASK)) - 1),
+ .suspend_sleep = REG_FIELD(DA9062AA_VBUCK3_B,
+ __builtin_ffs((int)DA9062AA_BUCK3_SL_B_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK3_SL_B_MASK)) - 1),
+ .suspend_vsel_reg = DA9062AA_VBUCK3_B,
+ .mode = REG_FIELD(DA9062AA_BUCK3_CFG,
+ __builtin_ffs((int)DA9062AA_BUCK3_MODE_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK3_MODE_MASK)) - 1),
+ .suspend = REG_FIELD(DA9062AA_DVC_1,
+ __builtin_ffs((int)DA9062AA_VBUCK3_SEL_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_VBUCK3_SEL_MASK)) - 1),
+ .ilimit = REG_FIELD(DA9062AA_BUCK_ILIM_A,
+ __builtin_ffs((int)DA9062AA_BUCK3_ILIM_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK3_ILIM_MASK)) - 1),
+ },
+ {
+ .desc.id = DA9061_ID_BUCK3,
+ .desc.name = "DA9061 BUCK3",
+ .desc.of_match = of_match_ptr("buck3"),
+ .desc.regulators_node = of_match_ptr("regulators"),
+ .desc.ops = &da9062_buck_ops,
+ .desc.min_uV = (530) * 1000,
+ .desc.uV_step = (10) * 1000,
+ .desc.n_voltages = ((1800) - (530))/(10) + 1,
+ .current_limits = da9062_buck_a_limits,
+ .n_current_limits = ARRAY_SIZE(da9062_buck_a_limits),
+ .desc.enable_reg = DA9062AA_BUCK4_CONT,
+ .desc.enable_mask = DA9062AA_BUCK4_EN_MASK,
+ .desc.vsel_reg = DA9062AA_VBUCK4_A,
+ .desc.vsel_mask = DA9062AA_VBUCK4_A_MASK,
+ .desc.linear_min_sel = 0,
+ .sleep = REG_FIELD(DA9062AA_VBUCK4_A,
+ __builtin_ffs((int)DA9062AA_BUCK4_SL_A_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK4_SL_A_MASK)) - 1),
+ .suspend_sleep = REG_FIELD(DA9062AA_VBUCK4_B,
+ __builtin_ffs((int)DA9062AA_BUCK4_SL_B_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK4_SL_B_MASK)) - 1),
+ .suspend_vsel_reg = DA9062AA_VBUCK4_B,
+ .mode = REG_FIELD(DA9062AA_BUCK4_CFG,
+ __builtin_ffs((int)DA9062AA_BUCK4_MODE_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK4_MODE_MASK)) - 1),
+ .suspend = REG_FIELD(DA9062AA_DVC_1,
+ __builtin_ffs((int)DA9062AA_VBUCK4_SEL_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_VBUCK4_SEL_MASK)) - 1),
+ .ilimit = REG_FIELD(DA9062AA_BUCK_ILIM_B,
+ __builtin_ffs((int)DA9062AA_BUCK4_ILIM_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_BUCK4_ILIM_MASK)) - 1),
+ },
+ {
+ .desc.id = DA9061_ID_LDO1,
+ .desc.name = "DA9061 LDO1",
+ .desc.of_match = of_match_ptr("ldo1"),
+ .desc.regulators_node = of_match_ptr("regulators"),
+ .desc.ops = &da9062_ldo_ops,
+ .desc.min_uV = (900) * 1000,
+ .desc.uV_step = (50) * 1000,
+ .desc.n_voltages = ((3600) - (900))/(50) + 1,
+ .desc.enable_reg = DA9062AA_LDO1_CONT,
+ .desc.enable_mask = DA9062AA_LDO1_EN_MASK,
+ .desc.vsel_reg = DA9062AA_VLDO1_A,
+ .desc.vsel_mask = DA9062AA_VLDO1_A_MASK,
+ .desc.linear_min_sel = 0,
+ .sleep = REG_FIELD(DA9062AA_VLDO1_A,
+ __builtin_ffs((int)DA9062AA_LDO1_SL_A_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO1_SL_A_MASK)) - 1),
+ .suspend_sleep = REG_FIELD(DA9062AA_VLDO1_B,
+ __builtin_ffs((int)DA9062AA_LDO1_SL_B_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO1_SL_B_MASK)) - 1),
+ .suspend_vsel_reg = DA9062AA_VLDO1_B,
+ .suspend = REG_FIELD(DA9062AA_DVC_1,
+ __builtin_ffs((int)DA9062AA_VLDO1_SEL_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_VLDO1_SEL_MASK)) - 1),
+ .oc_event = REG_FIELD(DA9062AA_STATUS_D,
+ __builtin_ffs((int)DA9062AA_LDO1_ILIM_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO1_ILIM_MASK)) - 1),
+ },
+ {
+ .desc.id = DA9061_ID_LDO2,
+ .desc.name = "DA9061 LDO2",
+ .desc.of_match = of_match_ptr("ldo2"),
+ .desc.regulators_node = of_match_ptr("regulators"),
+ .desc.ops = &da9062_ldo_ops,
+ .desc.min_uV = (900) * 1000,
+ .desc.uV_step = (50) * 1000,
+ .desc.n_voltages = ((3600) - (600))/(50) + 1,
+ .desc.enable_reg = DA9062AA_LDO2_CONT,
+ .desc.enable_mask = DA9062AA_LDO2_EN_MASK,
+ .desc.vsel_reg = DA9062AA_VLDO2_A,
+ .desc.vsel_mask = DA9062AA_VLDO2_A_MASK,
+ .desc.linear_min_sel = 0,
+ .sleep = REG_FIELD(DA9062AA_VLDO2_A,
+ __builtin_ffs((int)DA9062AA_LDO2_SL_A_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO2_SL_A_MASK)) - 1),
+ .suspend_sleep = REG_FIELD(DA9062AA_VLDO2_B,
+ __builtin_ffs((int)DA9062AA_LDO2_SL_B_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO2_SL_B_MASK)) - 1),
+ .suspend_vsel_reg = DA9062AA_VLDO2_B,
+ .suspend = REG_FIELD(DA9062AA_DVC_1,
+ __builtin_ffs((int)DA9062AA_VLDO2_SEL_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_VLDO2_SEL_MASK)) - 1),
+ .oc_event = REG_FIELD(DA9062AA_STATUS_D,
+ __builtin_ffs((int)DA9062AA_LDO2_ILIM_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO2_ILIM_MASK)) - 1),
+ },
+ {
+ .desc.id = DA9061_ID_LDO3,
+ .desc.name = "DA9061 LDO3",
+ .desc.of_match = of_match_ptr("ldo3"),
+ .desc.regulators_node = of_match_ptr("regulators"),
+ .desc.ops = &da9062_ldo_ops,
+ .desc.min_uV = (900) * 1000,
+ .desc.uV_step = (50) * 1000,
+ .desc.n_voltages = ((3600) - (900))/(50) + 1,
+ .desc.enable_reg = DA9062AA_LDO3_CONT,
+ .desc.enable_mask = DA9062AA_LDO3_EN_MASK,
+ .desc.vsel_reg = DA9062AA_VLDO3_A,
+ .desc.vsel_mask = DA9062AA_VLDO3_A_MASK,
+ .desc.linear_min_sel = 0,
+ .sleep = REG_FIELD(DA9062AA_VLDO3_A,
+ __builtin_ffs((int)DA9062AA_LDO3_SL_A_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO3_SL_A_MASK)) - 1),
+ .suspend_sleep = REG_FIELD(DA9062AA_VLDO3_B,
+ __builtin_ffs((int)DA9062AA_LDO3_SL_B_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO3_SL_B_MASK)) - 1),
+ .suspend_vsel_reg = DA9062AA_VLDO3_B,
+ .suspend = REG_FIELD(DA9062AA_DVC_1,
+ __builtin_ffs((int)DA9062AA_VLDO3_SEL_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_VLDO3_SEL_MASK)) - 1),
+ .oc_event = REG_FIELD(DA9062AA_STATUS_D,
+ __builtin_ffs((int)DA9062AA_LDO3_ILIM_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO3_ILIM_MASK)) - 1),
+ },
+ {
+ .desc.id = DA9061_ID_LDO4,
+ .desc.name = "DA9061 LDO4",
+ .desc.of_match = of_match_ptr("ldo4"),
+ .desc.regulators_node = of_match_ptr("regulators"),
+ .desc.ops = &da9062_ldo_ops,
+ .desc.min_uV = (900) * 1000,
+ .desc.uV_step = (50) * 1000,
+ .desc.n_voltages = ((3600) - (900))/(50) + 1,
+ .desc.enable_reg = DA9062AA_LDO4_CONT,
+ .desc.enable_mask = DA9062AA_LDO4_EN_MASK,
+ .desc.vsel_reg = DA9062AA_VLDO4_A,
+ .desc.vsel_mask = DA9062AA_VLDO4_A_MASK,
+ .desc.linear_min_sel = 0,
+ .sleep = REG_FIELD(DA9062AA_VLDO4_A,
+ __builtin_ffs((int)DA9062AA_LDO4_SL_A_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO4_SL_A_MASK)) - 1),
+ .suspend_sleep = REG_FIELD(DA9062AA_VLDO4_B,
+ __builtin_ffs((int)DA9062AA_LDO4_SL_B_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO4_SL_B_MASK)) - 1),
+ .suspend_vsel_reg = DA9062AA_VLDO4_B,
+ .suspend = REG_FIELD(DA9062AA_DVC_1,
+ __builtin_ffs((int)DA9062AA_VLDO4_SEL_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_VLDO4_SEL_MASK)) - 1),
+ .oc_event = REG_FIELD(DA9062AA_STATUS_D,
+ __builtin_ffs((int)DA9062AA_LDO4_ILIM_MASK) - 1,
+ sizeof(unsigned int) * 8 -
+ __builtin_clz((DA9062AA_LDO4_ILIM_MASK)) - 1),
+ },
+};
+
+/* DA9062 Regulator information */
+static const struct da9062_regulator_info local_da9062_regulator_info[] = {
{
.desc.id = DA9062_ID_BUCK1,
.desc.name = "DA9062 BUCK1",
@@ -727,17 +990,33 @@ static int da9062_regulator_probe(struct platform_device *pdev)
struct da9062_regulators *regulators;
struct da9062_regulator *regl;
struct regulator_config config = { };
+ const struct da9062_regulator_info *rinfo;
int irq, n, ret;
size_t size;
+ int max_regulators;
+
+ switch (chip->chip_type) {
+ case COMPAT_TYPE_DA9061:
+ max_regulators = DA9061_MAX_REGULATORS;
+ rinfo = local_da9061_regulator_info;
+ break;
+ case COMPAT_TYPE_DA9062:
+ max_regulators = DA9062_MAX_REGULATORS;
+ rinfo = local_da9062_regulator_info;
+ break;
+ default:
+ dev_err(chip->dev, "Unrecognised chip type\n");
+ return -ENODEV;
+ }
/* Allocate memory required by usable regulators */
size = sizeof(struct da9062_regulators) +
- DA9062_MAX_REGULATORS * sizeof(struct da9062_regulator);
+ max_regulators * sizeof(struct da9062_regulator);
regulators = devm_kzalloc(&pdev->dev, size, GFP_KERNEL);
if (!regulators)
return -ENOMEM;
- regulators->n_regulators = DA9062_MAX_REGULATORS;
+ regulators->n_regulators = max_regulators;
platform_set_drvdata(pdev, regulators);
n = 0;
@@ -745,7 +1024,7 @@ static int da9062_regulator_probe(struct platform_device *pdev)
/* Initialise regulator structure */
regl = ®ulators->regulator[n];
regl->hw = chip;
- regl->info = &local_regulator_info[n];
+ regl->info = &rinfo[n];
regl->desc = regl->info->desc;
regl->desc.type = REGULATOR_VOLTAGE;
regl->desc.owner = THIS_MODULE;
@@ -836,6 +1115,6 @@ static void __exit da9062_regulator_cleanup(void)
/* Module information */
MODULE_AUTHOR("S Twiss <stwiss.opensource-WBD+wuPFNBhBDgjK7y7TUQ@public.gmane.org>");
-MODULE_DESCRIPTION("REGULATOR device driver for Dialog DA9062");
+MODULE_DESCRIPTION("REGULATOR device driver for Dialog DA9062 and DA9061");
MODULE_LICENSE("GPL");
MODULE_ALIAS("platform:da9062-regulators");
--
end-of-patch for PATCH V7
--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH V7 6/7] thermal: da9062/61: Thermal junction temperature monitoring driver
2017-03-28 14:43 [PATCH V7 0/7] da9061: DA9061 driver submission Steve Twiss
` (4 preceding siblings ...)
2017-03-28 14:43 ` Steve Twiss
@ 2017-03-28 14:43 ` Steve Twiss
2017-04-01 19:59 ` Eduardo Valentin
2017-03-28 14:43 ` Steve Twiss
2017-04-07 4:51 ` [PATCH V7 0/7] da9061: DA9061 driver submission Eduardo Valentin
7 siblings, 1 reply; 36+ messages in thread
From: Steve Twiss @ 2017-03-28 14:43 UTC (permalink / raw)
To: Eduardo Valentin, LINUX-KERNEL, LINUX-PM, Zhang Rui
Cc: DEVICETREE, Dmitry Torokhov, Guenter Roeck, LINUX-INPUT,
LINUX-WATCHDOG, Lee Jones, Liam Girdwood, Lukasz Luba,
Mark Brown, Mark Rutland, Rob Herring, Support Opensource,
Wim Van Sebroeck
From: Steve Twiss <stwiss.opensource@diasemi.com>
Add junction temperature monitoring supervisor device driver, compatible
with the DA9062 and DA9061 PMICs. A MODULE_DEVICE_TABLE() macro is added.
If the PMIC's internal junction temperature rises above T_WARN (125 degC)
an interrupt is issued. This T_WARN level is defined as the
THERMAL_TRIP_HOT trip-wire inside the device driver.
The thermal triggering mechanism is interrupt based and happens when the
temperature rises above a given threshold level. The component cannot
return an exact temperature, it only has knowledge if the temperature is
above or below a given threshold value. A status bit must be polled to
detect when the temperature falls below that threshold level again. A
kernel work queue is configured to repeatedly poll and detect when the
temperature falls below this trip-wire, between 1 and 10 second intervals
(defaulting at 3 seconds).
This scheme is provided as an example. It would be expected that any
final implementation will also include a notify() function and any of these
settings could be altered to match the application where appropriate.
When over-temperature is reached, the interrupt from the DA9061/2 will be
repeatedly triggered. The IRQ is therefore disabled when the first
over-temperature event happens and the status bit is polled using a
work-queue until it becomes false.
This strategy is designed to allow the periodic transmission of uevents
(HOT trip point) as the first level of temperature supervision method. It
is intended for non-invasive temperature control, where the necessary
measures for cooling the system down are left to the host software. Once
the temperature falls again, the IRQ is re-enabled so a new critical
over-temperature event can be detected.
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
---
This patch applies against linux-next and v4.11-rc3
v6 -> v7
- NO CODE CHANGE
- Compile tested ARCH=x86_64
v5 -> v6
- Patch renamed from [PATCH V5 7/8] to [PATCH V6 6/7]
- Rebased from v4.9 to v4.11-rc3
- Modify Copyright to match Dialog latest legal statement
- Various checkpatch warnings (from --strict) have been fixed
- Added COMPILE_TEST to Kconfig
v4 -> v5
- Rebased from v4.8 to v4.9
- Updates from comments by Eduardo Valentin
- Replace vendor defined dlg,tjunc-temp-polling-period-ms with standard
thermal core polling-delay-passive as part of the device tree
initialisation
- Change to the commit message content and device driver source code to
include an explanation of the repeated uevent strategy for monitoring
over-temperature
- Rename warning threshold name from TEMP_WARN to T_WARN to match the
latest datasheet naming convention
- Added reviewed-by Lukasz Luba to commit message
v3 -> v4
- Patch renamed from [PATCH V3 8/9] to [PATCH V4 7/8]
- Reordering of cancel_delayed_work_sync() in remove function
- dev_warn() message for out-of-range polling period requests
- Explanatory comment for expected values defined for
DEFAULT_POLLING_MS_PERIOD, MAX_POLLING_MS_PERIOD and
MIN_POLLING_MS_PERIOD
v2 -> v3
- Patch renamed from [PATCH V2 09/10] to [PATCH V3 8/9]
- Addition of MODULE_DEVICE_TABLE macro to allow modinfo additions
v1 -> v2
- Patch renamed from [PATCH V1 05/10] to [PATCH V2 09/10] -- these
changes were made to fix checkpatch warnings caused by the patch
set dependency order
- List the header files in alphabetical order
- Remove "GPL v2" and replace with MODULE_LICENSE("GPL") to match the
copyright "GNU Public License v2 or later" option in the header
comment for this file. See the allowed identifiers in the file
include/linux/module.h +170
- Remove notify function "da9062_thermal_notify" function.
- MODULE_AUTHOR() macros removes Company Name and just gives Name in
accordance with include/linux/module.h +200
- Remove the compatible "dlg,da9061-thermal" option in the of_device_id
struct table. This patch now assumes the use of a DA9062 fallback
compatible string in the DTS when using the DA9061 thermal component
of the DA9061 device.
- Re-ordered some assignments earlier in the probe() for thermal->hw,
thermal->polling_period, thermal->mode, thermal->dev
- Added further information in the patch description to explain the use
of the device driver's built-in work-queue.
Regards,
Steve Twiss, Dialog Semiconductor
drivers/thermal/Kconfig | 10 ++
drivers/thermal/Makefile | 1 +
drivers/thermal/da9062-thermal.c | 315 +++++++++++++++++++++++++++++++++++++++
3 files changed, 326 insertions(+)
create mode 100644 drivers/thermal/da9062-thermal.c
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index 776b3439..a784b02 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -303,6 +303,16 @@ config DB8500_CPUFREQ_COOLING
bound cpufreq cooling device turns active to set CPU frequency low to
cool down the CPU.
+config DA9062_THERMAL
+ tristate "DA9062/DA9061 Dialog Semiconductor thermal driver"
+ depends on MFD_DA9062 || COMPILE_TEST
+ depends on OF
+ help
+ Enable this for the Dialog Semiconductor thermal sensor driver.
+ This will report PMIC junction over-temperature for one thermal trip
+ zone.
+ Compatible with the DA9062 and DA9061 PMICs.
+
config INTEL_POWERCLAMP
tristate "Intel PowerClamp idle injection driver"
depends on THERMAL
diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
index 7adae20..297849e 100644
--- a/drivers/thermal/Makefile
+++ b/drivers/thermal/Makefile
@@ -42,6 +42,7 @@ obj-$(CONFIG_IMX_THERMAL) += imx_thermal.o
obj-$(CONFIG_MAX77620_THERMAL) += max77620_thermal.o
obj-$(CONFIG_QORIQ_THERMAL) += qoriq_thermal.o
obj-$(CONFIG_DB8500_CPUFREQ_COOLING) += db8500_cpufreq_cooling.o
+obj-$(CONFIG_DA9062_THERMAL) += da9062-thermal.o
obj-$(CONFIG_INTEL_POWERCLAMP) += intel_powerclamp.o
obj-$(CONFIG_X86_PKG_TEMP_THERMAL) += x86_pkg_temp_thermal.o
obj-$(CONFIG_INTEL_SOC_DTS_IOSF_CORE) += intel_soc_dts_iosf.o
diff --git a/drivers/thermal/da9062-thermal.c b/drivers/thermal/da9062-thermal.c
new file mode 100644
index 0000000..dd8dd94
--- /dev/null
+++ b/drivers/thermal/da9062-thermal.c
@@ -0,0 +1,315 @@
+/*
+ * Thermal device driver for DA9062 and DA9061
+ * Copyright (C) 2017 Dialog Semiconductor
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/* When over-temperature is reached, an interrupt from the device will be
+ * triggered. Following this event the interrupt will be disabled and
+ * periodic transmission of uevents (HOT trip point) should define the
+ * first level of temperature supervision. It is expected that any final
+ * implementation of the thermal driver will include a .notify() function
+ * to implement these uevents to userspace.
+ *
+ * These uevents are intended to indicate non-invasive temperature control
+ * of the system, where the necessary measures for cooling are the
+ * responsibility of the host software. Once the temperature falls again,
+ * the IRQ is re-enabled so the start of a new over-temperature event can
+ * be detected without constant software monitoring.
+ */
+
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/thermal.h>
+#include <linux/workqueue.h>
+
+#include <linux/mfd/da9062/core.h>
+#include <linux/mfd/da9062/registers.h>
+
+/* Minimum, maximum and default polling millisecond periods are provided
+ * here as an example. It is expected that any final implementation to also
+ * include a modification of these settings to match the required
+ * application.
+ */
+#define DA9062_DEFAULT_POLLING_MS_PERIOD 3000
+#define DA9062_MAX_POLLING_MS_PERIOD 10000
+#define DA9062_MIN_POLLING_MS_PERIOD 1000
+
+#define DA9062_MILLI_CELSIUS(t) ((t) * 1000)
+
+struct da9062_thermal_config {
+ const char *name;
+};
+
+struct da9062_thermal {
+ struct da9062 *hw;
+ struct delayed_work work;
+ struct thermal_zone_device *zone;
+ enum thermal_device_mode mode;
+ struct mutex lock; /* protection for da9062_thermal temperature */
+ int temperature;
+ int irq;
+ const struct da9062_thermal_config *config;
+ struct device *dev;
+};
+
+static void da9062_thermal_poll_on(struct work_struct *work)
+{
+ struct da9062_thermal *thermal = container_of(work,
+ struct da9062_thermal,
+ work.work);
+ unsigned long delay;
+ unsigned int val;
+ int ret;
+
+ /* clear E_TEMP */
+ ret = regmap_write(thermal->hw->regmap,
+ DA9062AA_EVENT_B,
+ DA9062AA_E_TEMP_MASK);
+ if (ret < 0) {
+ dev_err(thermal->dev,
+ "Cannot clear the TJUNC temperature status\n");
+ goto err_enable_irq;
+ }
+
+ /* Now read E_TEMP again: it is acting like a status bit.
+ * If over-temperature, then this status will be true.
+ * If not over-temperature, this status will be false.
+ */
+ ret = regmap_read(thermal->hw->regmap,
+ DA9062AA_EVENT_B,
+ &val);
+ if (ret < 0) {
+ dev_err(thermal->dev,
+ "Cannot check the TJUNC temperature status\n");
+ goto err_enable_irq;
+ }
+
+ if (val & DA9062AA_E_TEMP_MASK) {
+ mutex_lock(&thermal->lock);
+ thermal->temperature = DA9062_MILLI_CELSIUS(125);
+ mutex_unlock(&thermal->lock);
+ thermal_zone_device_update(thermal->zone,
+ THERMAL_EVENT_UNSPECIFIED);
+
+ delay = msecs_to_jiffies(thermal->zone->passive_delay);
+ schedule_delayed_work(&thermal->work, delay);
+ return;
+ }
+
+ mutex_lock(&thermal->lock);
+ thermal->temperature = DA9062_MILLI_CELSIUS(0);
+ mutex_unlock(&thermal->lock);
+ thermal_zone_device_update(thermal->zone,
+ THERMAL_EVENT_UNSPECIFIED);
+
+err_enable_irq:
+ enable_irq(thermal->irq);
+}
+
+static irqreturn_t da9062_thermal_irq_handler(int irq, void *data)
+{
+ struct da9062_thermal *thermal = data;
+
+ disable_irq_nosync(thermal->irq);
+ schedule_delayed_work(&thermal->work, 0);
+
+ return IRQ_HANDLED;
+}
+
+static int da9062_thermal_get_mode(struct thermal_zone_device *z,
+ enum thermal_device_mode *mode)
+{
+ struct da9062_thermal *thermal = z->devdata;
+ *mode = thermal->mode;
+ return 0;
+}
+
+static int da9062_thermal_get_trip_type(struct thermal_zone_device *z,
+ int trip,
+ enum thermal_trip_type *type)
+{
+ struct da9062_thermal *thermal = z->devdata;
+
+ switch (trip) {
+ case 0:
+ *type = THERMAL_TRIP_HOT;
+ break;
+ default:
+ dev_err(thermal->dev,
+ "Driver does not support more than 1 trip-wire\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int da9062_thermal_get_trip_temp(struct thermal_zone_device *z,
+ int trip,
+ int *temp)
+{
+ struct da9062_thermal *thermal = z->devdata;
+
+ switch (trip) {
+ case 0:
+ *temp = DA9062_MILLI_CELSIUS(125);
+ break;
+ default:
+ dev_err(thermal->dev,
+ "Driver does not support more than 1 trip-wire\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int da9062_thermal_get_temp(struct thermal_zone_device *z,
+ int *temp)
+{
+ struct da9062_thermal *thermal = z->devdata;
+
+ mutex_lock(&thermal->lock);
+ *temp = thermal->temperature;
+ mutex_unlock(&thermal->lock);
+
+ return 0;
+}
+
+static struct thermal_zone_device_ops da9062_thermal_ops = {
+ .get_temp = da9062_thermal_get_temp,
+ .get_mode = da9062_thermal_get_mode,
+ .get_trip_type = da9062_thermal_get_trip_type,
+ .get_trip_temp = da9062_thermal_get_trip_temp,
+};
+
+static const struct da9062_thermal_config da9062_config = {
+ .name = "da9062-thermal",
+};
+
+static const struct of_device_id da9062_compatible_reg_id_table[] = {
+ { .compatible = "dlg,da9062-thermal", .data = &da9062_config },
+ { },
+};
+
+MODULE_DEVICE_TABLE(of, da9062_compatible_reg_id_table);
+
+static int da9062_thermal_probe(struct platform_device *pdev)
+{
+ struct da9062 *chip = dev_get_drvdata(pdev->dev.parent);
+ struct da9062_thermal *thermal;
+ unsigned int pp_tmp = DA9062_DEFAULT_POLLING_MS_PERIOD;
+ const struct of_device_id *match;
+ int ret = 0;
+
+ match = of_match_node(da9062_compatible_reg_id_table,
+ pdev->dev.of_node);
+ if (!match)
+ return -ENXIO;
+
+ if (pdev->dev.of_node) {
+ if (!of_property_read_u32(pdev->dev.of_node,
+ "polling-delay-passive",
+ &pp_tmp)) {
+ if (pp_tmp < DA9062_MIN_POLLING_MS_PERIOD ||
+ pp_tmp > DA9062_MAX_POLLING_MS_PERIOD) {
+ dev_warn(&pdev->dev,
+ "Out-of-range polling period %d ms\n",
+ pp_tmp);
+ pp_tmp = DA9062_DEFAULT_POLLING_MS_PERIOD;
+ }
+ }
+ }
+
+ thermal = devm_kzalloc(&pdev->dev, sizeof(struct da9062_thermal),
+ GFP_KERNEL);
+ if (!thermal) {
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ thermal->config = match->data;
+ thermal->hw = chip;
+ thermal->mode = THERMAL_DEVICE_ENABLED;
+ thermal->dev = &pdev->dev;
+
+ INIT_DELAYED_WORK(&thermal->work, da9062_thermal_poll_on);
+ mutex_init(&thermal->lock);
+
+ thermal->zone = thermal_zone_device_register(thermal->config->name,
+ 1, 0, thermal,
+ &da9062_thermal_ops, NULL, pp_tmp,
+ 0);
+ if (IS_ERR(thermal->zone)) {
+ dev_err(&pdev->dev, "Cannot register thermal zone device\n");
+ ret = PTR_ERR(thermal->zone);
+ goto err;
+ }
+
+ dev_dbg(&pdev->dev,
+ "TJUNC temperature polling period set at %d ms\n",
+ thermal->zone->passive_delay);
+
+ ret = platform_get_irq_byname(pdev, "THERMAL");
+ if (ret < 0) {
+ dev_err(&pdev->dev, "Failed to get platform IRQ.\n");
+ goto err_zone;
+ }
+ thermal->irq = ret;
+
+ ret = request_threaded_irq(thermal->irq, NULL,
+ da9062_thermal_irq_handler,
+ IRQF_TRIGGER_LOW | IRQF_ONESHOT,
+ "THERMAL", thermal);
+ if (ret) {
+ dev_err(&pdev->dev,
+ "Failed to request thermal device IRQ.\n");
+ goto err_zone;
+ }
+
+ platform_set_drvdata(pdev, thermal);
+ return 0;
+
+err_zone:
+ thermal_zone_device_unregister(thermal->zone);
+err:
+ return ret;
+}
+
+static int da9062_thermal_remove(struct platform_device *pdev)
+{
+ struct da9062_thermal *thermal = platform_get_drvdata(pdev);
+
+ free_irq(thermal->irq, thermal);
+ cancel_delayed_work_sync(&thermal->work);
+ thermal_zone_device_unregister(thermal->zone);
+ return 0;
+}
+
+static struct platform_driver da9062_thermal_driver = {
+ .probe = da9062_thermal_probe,
+ .remove = da9062_thermal_remove,
+ .driver = {
+ .name = "da9062-thermal",
+ .of_match_table = da9062_compatible_reg_id_table,
+ },
+};
+
+module_platform_driver(da9062_thermal_driver);
+
+MODULE_AUTHOR("Steve Twiss");
+MODULE_DESCRIPTION("Thermal TJUNC device driver for Dialog DA9062 and DA9061");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:da9062-thermal");
--
end-of-patch for PATCH V7
^ permalink raw reply related [flat|nested] 36+ messages in thread* Re: [PATCH V7 6/7] thermal: da9062/61: Thermal junction temperature monitoring driver
2017-03-28 14:43 ` [PATCH V7 6/7] thermal: da9062/61: Thermal junction temperature monitoring driver Steve Twiss
@ 2017-04-01 19:59 ` Eduardo Valentin
2017-04-03 13:21 ` Steve Twiss
0 siblings, 1 reply; 36+ messages in thread
From: Eduardo Valentin @ 2017-04-01 19:59 UTC (permalink / raw)
To: Steve Twiss
Cc: LINUX-KERNEL, LINUX-PM, Zhang Rui, DEVICETREE, Dmitry Torokhov,
Guenter Roeck, LINUX-INPUT, LINUX-WATCHDOG, Lee Jones,
Liam Girdwood, Lukasz Luba, Mark Brown, Mark Rutland,
Rob Herring, Support Opensource, Wim Van Sebroeck
Hello,
On Tue, Mar 28, 2017 at 03:43:33PM +0100, Steve Twiss wrote:
> From: Steve Twiss <stwiss.opensource@diasemi.com>
>
> Add junction temperature monitoring supervisor device driver, compatible
> with the DA9062 and DA9061 PMICs. A MODULE_DEVICE_TABLE() macro is added.
>
> If the PMIC's internal junction temperature rises above T_WARN (125 degC)
> an interrupt is issued. This T_WARN level is defined as the
> THERMAL_TRIP_HOT trip-wire inside the device driver.
>
> The thermal triggering mechanism is interrupt based and happens when the
> temperature rises above a given threshold level. The component cannot
> return an exact temperature, it only has knowledge if the temperature is
> above or below a given threshold value. A status bit must be polled to
> detect when the temperature falls below that threshold level again. A
> kernel work queue is configured to repeatedly poll and detect when the
> temperature falls below this trip-wire, between 1 and 10 second intervals
> (defaulting at 3 seconds).
>
> This scheme is provided as an example. It would be expected that any
> final implementation will also include a notify() function and any of these
> settings could be altered to match the application where appropriate.
>
> When over-temperature is reached, the interrupt from the DA9061/2 will be
> repeatedly triggered. The IRQ is therefore disabled when the first
> over-temperature event happens and the status bit is polled using a
> work-queue until it becomes false.
>
> This strategy is designed to allow the periodic transmission of uevents
> (HOT trip point) as the first level of temperature supervision method. It
> is intended for non-invasive temperature control, where the necessary
> measures for cooling the system down are left to the host software. Once
> the temperature falls again, the IRQ is re-enabled so a new critical
> over-temperature event can be detected.
>
> Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
I have had a look on the history of this driver on its previous
versions, and I do not think I have any other point to request on it.
Obviously, I still need to state that I do not like its oddness as it is
not really benefiting much of the thermal control implemented on the
thermal subsystem.
What is the plan for this series? Am I expected to get this driver
through thermal tree ? Or is this series going into a one shot?
If option 1 is the expected, would the driver need to get its
mfd parent merged first?
>
> ---
> This patch applies against linux-next and v4.11-rc3
>
> v6 -> v7
> - NO CODE CHANGE
> - Compile tested ARCH=x86_64
>
> v5 -> v6
> - Patch renamed from [PATCH V5 7/8] to [PATCH V6 6/7]
> - Rebased from v4.9 to v4.11-rc3
> - Modify Copyright to match Dialog latest legal statement
> - Various checkpatch warnings (from --strict) have been fixed
> - Added COMPILE_TEST to Kconfig
>
> v4 -> v5
> - Rebased from v4.8 to v4.9
> - Updates from comments by Eduardo Valentin
> - Replace vendor defined dlg,tjunc-temp-polling-period-ms with standard
> thermal core polling-delay-passive as part of the device tree
> initialisation
> - Change to the commit message content and device driver source code to
> include an explanation of the repeated uevent strategy for monitoring
> over-temperature
> - Rename warning threshold name from TEMP_WARN to T_WARN to match the
> latest datasheet naming convention
> - Added reviewed-by Lukasz Luba to commit message
>
> v3 -> v4
> - Patch renamed from [PATCH V3 8/9] to [PATCH V4 7/8]
> - Reordering of cancel_delayed_work_sync() in remove function
> - dev_warn() message for out-of-range polling period requests
> - Explanatory comment for expected values defined for
> DEFAULT_POLLING_MS_PERIOD, MAX_POLLING_MS_PERIOD and
> MIN_POLLING_MS_PERIOD
>
> v2 -> v3
> - Patch renamed from [PATCH V2 09/10] to [PATCH V3 8/9]
> - Addition of MODULE_DEVICE_TABLE macro to allow modinfo additions
>
> v1 -> v2
> - Patch renamed from [PATCH V1 05/10] to [PATCH V2 09/10] -- these
> changes were made to fix checkpatch warnings caused by the patch
> set dependency order
> - List the header files in alphabetical order
> - Remove "GPL v2" and replace with MODULE_LICENSE("GPL") to match the
> copyright "GNU Public License v2 or later" option in the header
> comment for this file. See the allowed identifiers in the file
> include/linux/module.h +170
> - Remove notify function "da9062_thermal_notify" function.
> - MODULE_AUTHOR() macros removes Company Name and just gives Name in
> accordance with include/linux/module.h +200
> - Remove the compatible "dlg,da9061-thermal" option in the of_device_id
> struct table. This patch now assumes the use of a DA9062 fallback
> compatible string in the DTS when using the DA9061 thermal component
> of the DA9061 device.
> - Re-ordered some assignments earlier in the probe() for thermal->hw,
> thermal->polling_period, thermal->mode, thermal->dev
> - Added further information in the patch description to explain the use
> of the device driver's built-in work-queue.
>
> Regards,
> Steve Twiss, Dialog Semiconductor
>
>
> drivers/thermal/Kconfig | 10 ++
> drivers/thermal/Makefile | 1 +
> drivers/thermal/da9062-thermal.c | 315 +++++++++++++++++++++++++++++++++++++++
> 3 files changed, 326 insertions(+)
> create mode 100644 drivers/thermal/da9062-thermal.c
>
> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
> index 776b3439..a784b02 100644
> --- a/drivers/thermal/Kconfig
> +++ b/drivers/thermal/Kconfig
> @@ -303,6 +303,16 @@ config DB8500_CPUFREQ_COOLING
> bound cpufreq cooling device turns active to set CPU frequency low to
> cool down the CPU.
>
> +config DA9062_THERMAL
> + tristate "DA9062/DA9061 Dialog Semiconductor thermal driver"
> + depends on MFD_DA9062 || COMPILE_TEST
> + depends on OF
> + help
> + Enable this for the Dialog Semiconductor thermal sensor driver.
> + This will report PMIC junction over-temperature for one thermal trip
> + zone.
> + Compatible with the DA9062 and DA9061 PMICs.
> +
> config INTEL_POWERCLAMP
> tristate "Intel PowerClamp idle injection driver"
> depends on THERMAL
> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
> index 7adae20..297849e 100644
> --- a/drivers/thermal/Makefile
> +++ b/drivers/thermal/Makefile
> @@ -42,6 +42,7 @@ obj-$(CONFIG_IMX_THERMAL) += imx_thermal.o
> obj-$(CONFIG_MAX77620_THERMAL) += max77620_thermal.o
> obj-$(CONFIG_QORIQ_THERMAL) += qoriq_thermal.o
> obj-$(CONFIG_DB8500_CPUFREQ_COOLING) += db8500_cpufreq_cooling.o
> +obj-$(CONFIG_DA9062_THERMAL) += da9062-thermal.o
> obj-$(CONFIG_INTEL_POWERCLAMP) += intel_powerclamp.o
> obj-$(CONFIG_X86_PKG_TEMP_THERMAL) += x86_pkg_temp_thermal.o
> obj-$(CONFIG_INTEL_SOC_DTS_IOSF_CORE) += intel_soc_dts_iosf.o
> diff --git a/drivers/thermal/da9062-thermal.c b/drivers/thermal/da9062-thermal.c
> new file mode 100644
> index 0000000..dd8dd94
> --- /dev/null
> +++ b/drivers/thermal/da9062-thermal.c
> @@ -0,0 +1,315 @@
> +/*
> + * Thermal device driver for DA9062 and DA9061
> + * Copyright (C) 2017 Dialog Semiconductor
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * as published by the Free Software Foundation; either version 2
> + * of the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +/* When over-temperature is reached, an interrupt from the device will be
> + * triggered. Following this event the interrupt will be disabled and
> + * periodic transmission of uevents (HOT trip point) should define the
> + * first level of temperature supervision. It is expected that any final
> + * implementation of the thermal driver will include a .notify() function
> + * to implement these uevents to userspace.
> + *
> + * These uevents are intended to indicate non-invasive temperature control
> + * of the system, where the necessary measures for cooling are the
> + * responsibility of the host software. Once the temperature falls again,
> + * the IRQ is re-enabled so the start of a new over-temperature event can
> + * be detected without constant software monitoring.
> + */
> +
> +#include <linux/errno.h>
> +#include <linux/interrupt.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/thermal.h>
> +#include <linux/workqueue.h>
> +
> +#include <linux/mfd/da9062/core.h>
> +#include <linux/mfd/da9062/registers.h>
> +
> +/* Minimum, maximum and default polling millisecond periods are provided
> + * here as an example. It is expected that any final implementation to also
> + * include a modification of these settings to match the required
> + * application.
> + */
> +#define DA9062_DEFAULT_POLLING_MS_PERIOD 3000
> +#define DA9062_MAX_POLLING_MS_PERIOD 10000
> +#define DA9062_MIN_POLLING_MS_PERIOD 1000
> +
> +#define DA9062_MILLI_CELSIUS(t) ((t) * 1000)
> +
> +struct da9062_thermal_config {
> + const char *name;
> +};
> +
> +struct da9062_thermal {
> + struct da9062 *hw;
> + struct delayed_work work;
> + struct thermal_zone_device *zone;
> + enum thermal_device_mode mode;
> + struct mutex lock; /* protection for da9062_thermal temperature */
> + int temperature;
> + int irq;
> + const struct da9062_thermal_config *config;
> + struct device *dev;
> +};
> +
> +static void da9062_thermal_poll_on(struct work_struct *work)
> +{
> + struct da9062_thermal *thermal = container_of(work,
> + struct da9062_thermal,
> + work.work);
> + unsigned long delay;
> + unsigned int val;
> + int ret;
> +
> + /* clear E_TEMP */
> + ret = regmap_write(thermal->hw->regmap,
> + DA9062AA_EVENT_B,
> + DA9062AA_E_TEMP_MASK);
> + if (ret < 0) {
> + dev_err(thermal->dev,
> + "Cannot clear the TJUNC temperature status\n");
> + goto err_enable_irq;
> + }
> +
> + /* Now read E_TEMP again: it is acting like a status bit.
> + * If over-temperature, then this status will be true.
> + * If not over-temperature, this status will be false.
> + */
> + ret = regmap_read(thermal->hw->regmap,
> + DA9062AA_EVENT_B,
> + &val);
> + if (ret < 0) {
> + dev_err(thermal->dev,
> + "Cannot check the TJUNC temperature status\n");
> + goto err_enable_irq;
> + }
> +
> + if (val & DA9062AA_E_TEMP_MASK) {
> + mutex_lock(&thermal->lock);
> + thermal->temperature = DA9062_MILLI_CELSIUS(125);
> + mutex_unlock(&thermal->lock);
> + thermal_zone_device_update(thermal->zone,
> + THERMAL_EVENT_UNSPECIFIED);
> +
> + delay = msecs_to_jiffies(thermal->zone->passive_delay);
> + schedule_delayed_work(&thermal->work, delay);
> + return;
> + }
> +
> + mutex_lock(&thermal->lock);
> + thermal->temperature = DA9062_MILLI_CELSIUS(0);
> + mutex_unlock(&thermal->lock);
> + thermal_zone_device_update(thermal->zone,
> + THERMAL_EVENT_UNSPECIFIED);
> +
> +err_enable_irq:
> + enable_irq(thermal->irq);
> +}
> +
> +static irqreturn_t da9062_thermal_irq_handler(int irq, void *data)
> +{
> + struct da9062_thermal *thermal = data;
> +
> + disable_irq_nosync(thermal->irq);
> + schedule_delayed_work(&thermal->work, 0);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int da9062_thermal_get_mode(struct thermal_zone_device *z,
> + enum thermal_device_mode *mode)
> +{
> + struct da9062_thermal *thermal = z->devdata;
> + *mode = thermal->mode;
> + return 0;
> +}
> +
> +static int da9062_thermal_get_trip_type(struct thermal_zone_device *z,
> + int trip,
> + enum thermal_trip_type *type)
> +{
> + struct da9062_thermal *thermal = z->devdata;
> +
> + switch (trip) {
> + case 0:
> + *type = THERMAL_TRIP_HOT;
> + break;
> + default:
> + dev_err(thermal->dev,
> + "Driver does not support more than 1 trip-wire\n");
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static int da9062_thermal_get_trip_temp(struct thermal_zone_device *z,
> + int trip,
> + int *temp)
> +{
> + struct da9062_thermal *thermal = z->devdata;
> +
> + switch (trip) {
> + case 0:
> + *temp = DA9062_MILLI_CELSIUS(125);
> + break;
> + default:
> + dev_err(thermal->dev,
> + "Driver does not support more than 1 trip-wire\n");
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static int da9062_thermal_get_temp(struct thermal_zone_device *z,
> + int *temp)
> +{
> + struct da9062_thermal *thermal = z->devdata;
> +
> + mutex_lock(&thermal->lock);
> + *temp = thermal->temperature;
> + mutex_unlock(&thermal->lock);
> +
> + return 0;
> +}
> +
> +static struct thermal_zone_device_ops da9062_thermal_ops = {
> + .get_temp = da9062_thermal_get_temp,
> + .get_mode = da9062_thermal_get_mode,
> + .get_trip_type = da9062_thermal_get_trip_type,
> + .get_trip_temp = da9062_thermal_get_trip_temp,
> +};
> +
> +static const struct da9062_thermal_config da9062_config = {
> + .name = "da9062-thermal",
> +};
> +
> +static const struct of_device_id da9062_compatible_reg_id_table[] = {
> + { .compatible = "dlg,da9062-thermal", .data = &da9062_config },
> + { },
> +};
> +
> +MODULE_DEVICE_TABLE(of, da9062_compatible_reg_id_table);
> +
> +static int da9062_thermal_probe(struct platform_device *pdev)
> +{
> + struct da9062 *chip = dev_get_drvdata(pdev->dev.parent);
> + struct da9062_thermal *thermal;
> + unsigned int pp_tmp = DA9062_DEFAULT_POLLING_MS_PERIOD;
> + const struct of_device_id *match;
> + int ret = 0;
> +
> + match = of_match_node(da9062_compatible_reg_id_table,
> + pdev->dev.of_node);
> + if (!match)
> + return -ENXIO;
> +
> + if (pdev->dev.of_node) {
> + if (!of_property_read_u32(pdev->dev.of_node,
> + "polling-delay-passive",
> + &pp_tmp)) {
> + if (pp_tmp < DA9062_MIN_POLLING_MS_PERIOD ||
> + pp_tmp > DA9062_MAX_POLLING_MS_PERIOD) {
> + dev_warn(&pdev->dev,
> + "Out-of-range polling period %d ms\n",
> + pp_tmp);
> + pp_tmp = DA9062_DEFAULT_POLLING_MS_PERIOD;
> + }
> + }
> + }
> +
> + thermal = devm_kzalloc(&pdev->dev, sizeof(struct da9062_thermal),
> + GFP_KERNEL);
> + if (!thermal) {
> + ret = -ENOMEM;
> + goto err;
> + }
> +
> + thermal->config = match->data;
> + thermal->hw = chip;
> + thermal->mode = THERMAL_DEVICE_ENABLED;
> + thermal->dev = &pdev->dev;
> +
> + INIT_DELAYED_WORK(&thermal->work, da9062_thermal_poll_on);
> + mutex_init(&thermal->lock);
> +
> + thermal->zone = thermal_zone_device_register(thermal->config->name,
> + 1, 0, thermal,
> + &da9062_thermal_ops, NULL, pp_tmp,
> + 0);
> + if (IS_ERR(thermal->zone)) {
> + dev_err(&pdev->dev, "Cannot register thermal zone device\n");
> + ret = PTR_ERR(thermal->zone);
> + goto err;
> + }
> +
> + dev_dbg(&pdev->dev,
> + "TJUNC temperature polling period set at %d ms\n",
> + thermal->zone->passive_delay);
> +
> + ret = platform_get_irq_byname(pdev, "THERMAL");
> + if (ret < 0) {
> + dev_err(&pdev->dev, "Failed to get platform IRQ.\n");
> + goto err_zone;
> + }
> + thermal->irq = ret;
> +
> + ret = request_threaded_irq(thermal->irq, NULL,
> + da9062_thermal_irq_handler,
> + IRQF_TRIGGER_LOW | IRQF_ONESHOT,
> + "THERMAL", thermal);
> + if (ret) {
> + dev_err(&pdev->dev,
> + "Failed to request thermal device IRQ.\n");
> + goto err_zone;
> + }
> +
> + platform_set_drvdata(pdev, thermal);
> + return 0;
> +
> +err_zone:
> + thermal_zone_device_unregister(thermal->zone);
> +err:
> + return ret;
> +}
> +
> +static int da9062_thermal_remove(struct platform_device *pdev)
> +{
> + struct da9062_thermal *thermal = platform_get_drvdata(pdev);
> +
> + free_irq(thermal->irq, thermal);
> + cancel_delayed_work_sync(&thermal->work);
> + thermal_zone_device_unregister(thermal->zone);
> + return 0;
> +}
> +
> +static struct platform_driver da9062_thermal_driver = {
> + .probe = da9062_thermal_probe,
> + .remove = da9062_thermal_remove,
> + .driver = {
> + .name = "da9062-thermal",
> + .of_match_table = da9062_compatible_reg_id_table,
> + },
> +};
> +
> +module_platform_driver(da9062_thermal_driver);
> +
> +MODULE_AUTHOR("Steve Twiss");
> +MODULE_DESCRIPTION("Thermal TJUNC device driver for Dialog DA9062 and DA9061");
> +MODULE_LICENSE("GPL");
> +MODULE_ALIAS("platform:da9062-thermal");
> --
> end-of-patch for PATCH V7
>
^ permalink raw reply [flat|nested] 36+ messages in thread* RE: [PATCH V7 6/7] thermal: da9062/61: Thermal junction temperature monitoring driver
2017-04-01 19:59 ` Eduardo Valentin
@ 2017-04-03 13:21 ` Steve Twiss
0 siblings, 0 replies; 36+ messages in thread
From: Steve Twiss @ 2017-04-03 13:21 UTC (permalink / raw)
To: Eduardo Valentin, Lee Jones
Cc: LINUX-KERNEL, LINUX-PM, Zhang Rui, DEVICETREE, Dmitry Torokhov,
Guenter Roeck, LINUX-INPUT, LINUX-WATCHDOG, Liam Girdwood,
Lukasz Luba, Mark Brown, Mark Rutland, Rob Herring,
Support Opensource, Wim Van Sebroeck
On 01 April 2017 @20:59, Eduardo Valentin wrote:
> Subject: Re: [PATCH V7 6/7] thermal: da9062/61: Thermal junction temperature monitoring driver
>
> On Tue, Mar 28, 2017 at 03:43:33PM +0100, Steve Twiss wrote:
> > From: Steve Twiss <stwiss.opensource@diasemi.com>
> >
> > Add junction temperature monitoring supervisor device driver, compatible
> > with the DA9062 and DA9061 PMICs. A MODULE_DEVICE_TABLE() macro is added.
> >
> > If the PMIC's internal junction temperature rises above T_WARN (125 degC)
> > an interrupt is issued. This T_WARN level is defined as the
> > THERMAL_TRIP_HOT trip-wire inside the device driver.
> >
> > The thermal triggering mechanism is interrupt based and happens when the
> > temperature rises above a given threshold level. The component cannot
> > return an exact temperature, it only has knowledge if the temperature is
> > above or below a given threshold value. A status bit must be polled to
> > detect when the temperature falls below that threshold level again. A
> > kernel work queue is configured to repeatedly poll and detect when the
> > temperature falls below this trip-wire, between 1 and 10 second intervals
> > (defaulting at 3 seconds).
> >
> > This scheme is provided as an example. It would be expected that any
> > final implementation will also include a notify() function and any of these
> > settings could be altered to match the application where appropriate.
> >
> > When over-temperature is reached, the interrupt from the DA9061/2 will be
> > repeatedly triggered. The IRQ is therefore disabled when the first
> > over-temperature event happens and the status bit is polled using a
> > work-queue until it becomes false.
> >
> > This strategy is designed to allow the periodic transmission of uevents
> > (HOT trip point) as the first level of temperature supervision method. It
> > is intended for non-invasive temperature control, where the necessary
> > measures for cooling the system down are left to the host software. Once
> > the temperature falls again, the IRQ is re-enabled so a new critical
> > over-temperature event can be detected.
> >
> > Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
> > Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
>
> I have had a look on the history of this driver on its previous
> versions, and I do not think I have any other point to request on it.
Thank you.
> Obviously, I still need to state that I do not like its oddness as it is
> not really benefiting much of the thermal control implemented on the
> thermal subsystem.
Agreed.
But, it should be useful in the case of an over-temperature in the system PMIC
when the OS needs to be notified to bring core temperature under control.
> What is the plan for this series? Am I expected to get this driver
> through thermal tree ? Or is this series going into a one shot?
>
> If option 1 is the expected, would the driver need to get its
> mfd parent merged first?
Other components such as the ONKEY and Watchdog have not required the MFD
to be merged first. I don't see any strong dependency for the MFD to exist with this
thermal component.
I'm not sure how much Lee is waiting for Acks to exist before proceeding with the MFD.
I have TO:'d Lee Jones, for this case.
Regards,
Steve
^ permalink raw reply [flat|nested] 36+ messages in thread
* RE: [PATCH V7 6/7] thermal: da9062/61: Thermal junction temperature monitoring driver
@ 2017-04-03 13:21 ` Steve Twiss
0 siblings, 0 replies; 36+ messages in thread
From: Steve Twiss @ 2017-04-03 13:21 UTC (permalink / raw)
To: Eduardo Valentin, Lee Jones
Cc: LINUX-KERNEL, LINUX-PM, Zhang Rui, DEVICETREE, Dmitry Torokhov,
Guenter Roeck, LINUX-INPUT, LINUX-WATCHDOG, Liam Girdwood,
Lukasz Luba, Mark Brown, Mark Rutland, Rob Herring,
Support Opensource, Wim Van Sebroeck
On 01 April 2017 @20:59, Eduardo Valentin wrote:
> Subject: Re: [PATCH V7 6/7] thermal: da9062/61: Thermal junction temperature monitoring driver
>
> On Tue, Mar 28, 2017 at 03:43:33PM +0100, Steve Twiss wrote:
> > From: Steve Twiss <stwiss.opensource@diasemi.com>
> >
> > Add junction temperature monitoring supervisor device driver, compatible
> > with the DA9062 and DA9061 PMICs. A MODULE_DEVICE_TABLE() macro is added.
> >
> > If the PMIC's internal junction temperature rises above T_WARN (125 degC)
> > an interrupt is issued. This T_WARN level is defined as the
> > THERMAL_TRIP_HOT trip-wire inside the device driver.
> >
> > The thermal triggering mechanism is interrupt based and happens when the
> > temperature rises above a given threshold level. The component cannot
> > return an exact temperature, it only has knowledge if the temperature is
> > above or below a given threshold value. A status bit must be polled to
> > detect when the temperature falls below that threshold level again. A
> > kernel work queue is configured to repeatedly poll and detect when the
> > temperature falls below this trip-wire, between 1 and 10 second intervals
> > (defaulting at 3 seconds).
> >
> > This scheme is provided as an example. It would be expected that any
> > final implementation will also include a notify() function and any of these
> > settings could be altered to match the application where appropriate.
> >
> > When over-temperature is reached, the interrupt from the DA9061/2 will be
> > repeatedly triggered. The IRQ is therefore disabled when the first
> > over-temperature event happens and the status bit is polled using a
> > work-queue until it becomes false.
> >
> > This strategy is designed to allow the periodic transmission of uevents
> > (HOT trip point) as the first level of temperature supervision method. It
> > is intended for non-invasive temperature control, where the necessary
> > measures for cooling the system down are left to the host software. Once
> > the temperature falls again, the IRQ is re-enabled so a new critical
> > over-temperature event can be detected.
> >
> > Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
> > Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
>
> I have had a look on the history of this driver on its previous
> versions, and I do not think I have any other point to request on it.
Thank you.
> Obviously, I still need to state that I do not like its oddness as it is
> not really benefiting much of the thermal control implemented on the
> thermal subsystem.
Agreed.
But, it should be useful in the case of an over-temperature in the system PMIC
when the OS needs to be notified to bring core temperature under control.
> What is the plan for this series? Am I expected to get this driver
> through thermal tree ? Or is this series going into a one shot?
>
> If option 1 is the expected, would the driver need to get its
> mfd parent merged first?
Other components such as the ONKEY and Watchdog have not required the MFD
to be merged first. I don't see any strong dependency for the MFD to exist with this
thermal component.
I'm not sure how much Lee is waiting for Acks to exist before proceeding with the MFD.
I have TO:'d Lee Jones, for this case.
Regards,
Steve
--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH V7 7/7] MAINTAINERS: da9062/61 updates to the Dialog Semiconductor search terms
2017-03-28 14:43 [PATCH V7 0/7] da9061: DA9061 driver submission Steve Twiss
@ 2017-03-28 14:43 ` Steve Twiss
2017-03-28 14:43 ` [PATCH V7 2/7] Documentation: devicetree: thermal: da9062/61 TJUNC temperature binding Steve Twiss
` (6 subsequent siblings)
7 siblings, 0 replies; 36+ messages in thread
From: Steve Twiss @ 2017-03-28 14:43 UTC (permalink / raw)
To: DEVICETREE, Dmitry Torokhov, Eduardo Valentin, Guenter Roeck,
LINUX-INPUT, LINUX-KERNEL, LINUX-PM, LINUX-WATCHDOG,
Mark Rutland, Rob Herring, Wim Van Sebroeck, Zhang Rui
Cc: DEVICETREE, LINUX-INPUT, LINUX-KERNEL, LINUX-PM, LINUX-WATCHDOG,
Lee Jones, Liam Girdwood, Mark Brown, Support Opensource
From: Steve Twiss <stwiss.opensource@diasemi.com>
Hi,
Dialog Semiconductor support would like to add to the MAINTAINERS search
terms. This update will allow us to follow files for device tree bindings
and source code relating to input onkey drivers, chip thermal monitoring
and watchdog timers.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
---
This patch applies against linux-next and v4.11-rc3
v6 -> v7
- NO CODE CHANGE
v5 -> v6
- NO CODE CHANGE
- Rebased from v4.8 to v4.11-rc3
- Patch renamed from [PATCH V5 8/8] to [PATCH V5 7/7]
v4 -> v5
- NO CODE CHANGE
- Rebased from v4.8 to v4.9
v3 -> v4
- NO CODE CHANGE
- Patch renamed from [PATCH V3 9/9] to [PATCH V4 8/8]
v2 -> v3
- NO CODE CHANGE
- Patch renamed from [PATCH V2 10/10] to [PATCH V3 9/9]
v1 -> v2
- NO CODE CHANGE
Hi,
This patch depends on acceptance of the following from this patch set:
- [PATCH V5 7/8] PMIC temperature monitoring
and also from the following binding file changes:
- Binding for onkey (already applied by Dmitry Torokhov)
- [PATCH V5 1/8] Binding for watchdog
- [PATCH V5 2/8] Binding for thermal
Regards,
Steve Twiss, Dialog Semiconductor
MAINTAINERS | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index c776906..bab1e77 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3926,7 +3926,10 @@ W: http://www.dialog-semiconductor.com/products
S: Supported
F: Documentation/hwmon/da90??
F: Documentation/devicetree/bindings/mfd/da90*.txt
+F: Documentation/devicetree/bindings/input/da90??-onkey.txt
+F: Documentation/devicetree/bindings/thermal/da90??-thermal.txt
F: Documentation/devicetree/bindings/regulator/da92*.txt
+F: Documentation/devicetree/bindings/watchdog/da92??-wdt.txt
F: Documentation/devicetree/bindings/sound/da[79]*.txt
F: drivers/gpio/gpio-da90??.c
F: drivers/hwmon/da90??-hwmon.c
@@ -3941,6 +3944,7 @@ F: drivers/power/supply/da9052-battery.c
F: drivers/power/supply/da91??-*.c
F: drivers/regulator/da903x.c
F: drivers/regulator/da9???-regulator.[ch]
+F: drivers/thermal/da90??-thermal.c
F: drivers/rtc/rtc-da90??.c
F: drivers/video/backlight/da90??_bl.c
F: drivers/watchdog/da90??_wdt.c
--
end-of-patch for PATCH V7
^ permalink raw reply related [flat|nested] 36+ messages in thread* [PATCH V7 7/7] MAINTAINERS: da9062/61 updates to the Dialog Semiconductor search terms
@ 2017-03-28 14:43 ` Steve Twiss
0 siblings, 0 replies; 36+ messages in thread
From: Steve Twiss @ 2017-03-28 14:43 UTC (permalink / raw)
To: Dmitry Torokhov, Eduardo Valentin, Guenter Roeck, Mark Rutland,
Rob Herring, Wim Van Sebroeck, Zhang Rui
Cc: DEVICETREE, LINUX-INPUT, LINUX-KERNEL, LINUX-PM, LINUX-WATCHDOG,
Lee Jones, Liam Girdwood, Mark Brown, Support Opensource
From: Steve Twiss <stwiss.opensource@diasemi.com>
Hi,
Dialog Semiconductor support would like to add to the MAINTAINERS search
terms. This update will allow us to follow files for device tree bindings
and source code relating to input onkey drivers, chip thermal monitoring
and watchdog timers.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
---
This patch applies against linux-next and v4.11-rc3
v6 -> v7
- NO CODE CHANGE
v5 -> v6
- NO CODE CHANGE
- Rebased from v4.8 to v4.11-rc3
- Patch renamed from [PATCH V5 8/8] to [PATCH V5 7/7]
v4 -> v5
- NO CODE CHANGE
- Rebased from v4.8 to v4.9
v3 -> v4
- NO CODE CHANGE
- Patch renamed from [PATCH V3 9/9] to [PATCH V4 8/8]
v2 -> v3
- NO CODE CHANGE
- Patch renamed from [PATCH V2 10/10] to [PATCH V3 9/9]
v1 -> v2
- NO CODE CHANGE
Hi,
This patch depends on acceptance of the following from this patch set:
- [PATCH V5 7/8] PMIC temperature monitoring
and also from the following binding file changes:
- Binding for onkey (already applied by Dmitry Torokhov)
- [PATCH V5 1/8] Binding for watchdog
- [PATCH V5 2/8] Binding for thermal
Regards,
Steve Twiss, Dialog Semiconductor
MAINTAINERS | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index c776906..bab1e77 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3926,7 +3926,10 @@ W: http://www.dialog-semiconductor.com/products
S: Supported
F: Documentation/hwmon/da90??
F: Documentation/devicetree/bindings/mfd/da90*.txt
+F: Documentation/devicetree/bindings/input/da90??-onkey.txt
+F: Documentation/devicetree/bindings/thermal/da90??-thermal.txt
F: Documentation/devicetree/bindings/regulator/da92*.txt
+F: Documentation/devicetree/bindings/watchdog/da92??-wdt.txt
F: Documentation/devicetree/bindings/sound/da[79]*.txt
F: drivers/gpio/gpio-da90??.c
F: drivers/hwmon/da90??-hwmon.c
@@ -3941,6 +3944,7 @@ F: drivers/power/supply/da9052-battery.c
F: drivers/power/supply/da91??-*.c
F: drivers/regulator/da903x.c
F: drivers/regulator/da9???-regulator.[ch]
+F: drivers/thermal/da90??-thermal.c
F: drivers/rtc/rtc-da90??.c
F: drivers/video/backlight/da90??_bl.c
F: drivers/watchdog/da90??_wdt.c
--
end-of-patch for PATCH V7
^ permalink raw reply related [flat|nested] 36+ messages in thread
* Re: [PATCH V7 0/7] da9061: DA9061 driver submission
2017-03-28 14:43 [PATCH V7 0/7] da9061: DA9061 driver submission Steve Twiss
` (6 preceding siblings ...)
2017-03-28 14:43 ` Steve Twiss
@ 2017-04-07 4:51 ` Eduardo Valentin
7 siblings, 0 replies; 36+ messages in thread
From: Eduardo Valentin @ 2017-04-07 4:51 UTC (permalink / raw)
To: Steve Twiss
Cc: DEVICETREE, Dmitry Torokhov, Guenter Roeck, LINUX-INPUT,
LINUX-KERNEL, LINUX-PM, LINUX-WATCHDOG, Lee Jones, Liam Girdwood,
Lukasz Luba, Mark Brown, Mark Rutland, Rob Herring,
Wim Van Sebroeck, Zhang Rui, Support Opensource
[-- Attachment #1: Type: text/plain, Size: 461 bytes --]
Hey,
On Tue, Mar 28, 2017 at 03:43:33PM +0100, Steve Twiss wrote:
> From: Steve Twiss <stwiss.opensource@diasemi.com>
>
> This patch set adds support for the Dialog DA9061 Power Management IC.
> Support is made by altering the existing DA9062 device driver, where
> appropriate.
>
> Hello,
>
> Previously, there were only minor changes for v6.
> The patch v7 introduces a compile test for x86 64-bit.
>
Applied patches 2 and 7 on my tree.
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH V7 4/7] mfd: da9061: MFD core support
[not found] <cover.1491230802.git.stwiss.opensource@diasemi.com>
@ 2017-04-03 14:46 ` Steve Twiss
2017-04-04 8:39 ` Lee Jones
0 siblings, 1 reply; 36+ messages in thread
From: Steve Twiss @ 2017-04-03 14:46 UTC (permalink / raw)
To: LINUX-KERNEL, Lee Jones
Cc: DEVICETREE, Dmitry Torokhov, Eduardo Valentin, Guenter Roeck,
LINUX-INPUT, LINUX-PM, LINUX-WATCHDOG, Liam Girdwood, Mark Brown,
Mark Rutland, Rob Herring, Support Opensource, Wim Van Sebroeck,
Zhang Rui
From: Steve Twiss <stwiss.opensource@diasemi.com>
MFD support for DA9061 is provided as part of the DA9062 device driver.
The registers header file adds two new chip variant IDs defined in DA9061
and DA9062 hardware. The core header file adds new software enumerations
for listing the valid DA9061 IRQs and a da9062_compatible_types enumeration
for distinguishing between DA9061/62 devices in software.
The core source code adds a new .compatible of_device_id entry. This is
extended from DA9062 to support both "dlg,da9061" and "dlg,da9062". The
.data entry now holds a reference to the enumerated device type.
A new regmap_irq_chip model is added for DA9061 and this supports the new
list of regmap_irq entries. A new mfd_cell da9061_devs[] array lists the
new sub system components for DA9061. Support is added for a new DA9061
regmap_config which lists the correct readable, writable and volatile
ranges for this chip.
The probe function uses the device tree compatible string to switch on the
da9062_compatible_types and configure the correct mfd cells, irq chip and
regmap config.
Kconfig is updated to reflect support for DA9061 and DA9062 PMICs.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
---
Acked-for-mfd-by: Lee Jones <lee.jones@linaro.org>
Hi Lee, that Ack was from your earlier posting:
https://lkml.org/lkml/2017/1/4/328 this was
Regards, Steve.
This patch applies against linux-next and v4.11-rc3
v6 -> v7 + update
- Removed brackets surrounding case statements for
case COMPAT_TYPE_DA9061:
case COMPAT_TYPE_DA9062:
v6 -> v7
- Remove compilation warning when casting a void * to an integer on
ARCH=x86_64 using -Wpointer-to-int-cast.
- Recommendation uintptr_t cast: https://lkml.org/lkml/2017/3/28/292
- Compile tested ARCH=x86_64
v5 -> v6
- Rebased from v4.9 to v4.11-rc3
- Modify Copyright to match Dialog latest legal statement
- Fixed "braces {} should be used on all arms" checkpatch warning
v4 -> v5
- NO CODE CHANGE
- Rebased from v4.8 to v4.9
v3 -> v4
- Patch renamed from [PATCH V3 5/9] to [PATCH V4 4/8]
- Removed DEFINE_RES_NAMED() macros for DA9061 resources and replaced
them with DEFINE_RES_IRQ_NAMED().
- Removed whitespace
- Reverted change for badly defined mfd_cell da9062_devs of_compatible
string from "dlg,da9062-watchdog" back to "dlg,da9062-wdt"
v2 -> v3
- NO CODE CHANGE
- Patch renamed from [PATCH V2 05/10] to [PATCH V3 5/9]
v1 -> v2
- Patch renamed from [PATCH V1 01/10] to [PATCH V2 05/10] -- these
changes were made to fix checkpatch warnings caused by the patch
set dependency order
- Fixed typo in the commit message "readble" to "readable"
- Removed the explicit cross-check to decide if there is a conflict
between the device tree compatible string and the hardware definition.
This patch assumes the device tree is correctly written and therefore
removes the need for a hardware/DT sanity check.
- Removed extra semicolon in drivers/mfd/da9062-core.c:877
- Re-write compatible entries into numerical order
Lee,
Changes as described in the version history above.
As previously:
This patch adds support for the DA9061 PMIC. This is done as part of the
existing DA9062 device driver by extending the of_device_id match table.
This in turn allows new MFD cells, irq chip and regmap definitions to
support DA9061.
Regards,
Steve Twiss, Dialog Semiconductor
drivers/mfd/Kconfig | 5 +-
drivers/mfd/da9062-core.c | 427 +++++++++++++++++++++++++++++++++--
include/linux/mfd/da9062/core.h | 29 ++-
include/linux/mfd/da9062/registers.h | 5 +-
4 files changed, 443 insertions(+), 23 deletions(-)
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 55ecdfb..29cc11a 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -263,13 +263,14 @@ config MFD_DA9055
called "da9055"
config MFD_DA9062
- tristate "Dialog Semiconductor DA9062 PMIC Support"
+ tristate "Dialog Semiconductor DA9062/61 PMIC Support"
select MFD_CORE
select REGMAP_I2C
select REGMAP_IRQ
depends on I2C
help
- Say yes here for support for the Dialog Semiconductor DA9062 PMIC.
+ Say yes here for support for the Dialog Semiconductor DA9061 and
+ DA9062 PMICs.
This includes the I2C driver and core APIs.
Additional drivers must be enabled in order to use the functionality
of the device.
diff --git a/drivers/mfd/da9062-core.c b/drivers/mfd/da9062-core.c
index 8f873866..1803f58 100644
--- a/drivers/mfd/da9062-core.c
+++ b/drivers/mfd/da9062-core.c
@@ -1,6 +1,6 @@
/*
- * Core, IRQ and I2C device driver for DA9062 PMIC
- * Copyright (C) 2015 Dialog Semiconductor Ltd.
+ * Core, IRQ and I2C device driver for DA9061 and DA9062 PMICs
+ * Copyright (C) 2015-2017 Dialog Semiconductor
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
@@ -30,6 +30,70 @@
#define DA9062_REG_EVENT_B_OFFSET 1
#define DA9062_REG_EVENT_C_OFFSET 2
+static struct regmap_irq da9061_irqs[] = {
+ /* EVENT A */
+ [DA9061_IRQ_ONKEY] = {
+ .reg_offset = DA9062_REG_EVENT_A_OFFSET,
+ .mask = DA9062AA_M_NONKEY_MASK,
+ },
+ [DA9061_IRQ_WDG_WARN] = {
+ .reg_offset = DA9062_REG_EVENT_A_OFFSET,
+ .mask = DA9062AA_M_WDG_WARN_MASK,
+ },
+ [DA9061_IRQ_SEQ_RDY] = {
+ .reg_offset = DA9062_REG_EVENT_A_OFFSET,
+ .mask = DA9062AA_M_SEQ_RDY_MASK,
+ },
+ /* EVENT B */
+ [DA9061_IRQ_TEMP] = {
+ .reg_offset = DA9062_REG_EVENT_B_OFFSET,
+ .mask = DA9062AA_M_TEMP_MASK,
+ },
+ [DA9061_IRQ_LDO_LIM] = {
+ .reg_offset = DA9062_REG_EVENT_B_OFFSET,
+ .mask = DA9062AA_M_LDO_LIM_MASK,
+ },
+ [DA9061_IRQ_DVC_RDY] = {
+ .reg_offset = DA9062_REG_EVENT_B_OFFSET,
+ .mask = DA9062AA_M_DVC_RDY_MASK,
+ },
+ [DA9061_IRQ_VDD_WARN] = {
+ .reg_offset = DA9062_REG_EVENT_B_OFFSET,
+ .mask = DA9062AA_M_VDD_WARN_MASK,
+ },
+ /* EVENT C */
+ [DA9061_IRQ_GPI0] = {
+ .reg_offset = DA9062_REG_EVENT_C_OFFSET,
+ .mask = DA9062AA_M_GPI0_MASK,
+ },
+ [DA9061_IRQ_GPI1] = {
+ .reg_offset = DA9062_REG_EVENT_C_OFFSET,
+ .mask = DA9062AA_M_GPI1_MASK,
+ },
+ [DA9061_IRQ_GPI2] = {
+ .reg_offset = DA9062_REG_EVENT_C_OFFSET,
+ .mask = DA9062AA_M_GPI2_MASK,
+ },
+ [DA9061_IRQ_GPI3] = {
+ .reg_offset = DA9062_REG_EVENT_C_OFFSET,
+ .mask = DA9062AA_M_GPI3_MASK,
+ },
+ [DA9061_IRQ_GPI4] = {
+ .reg_offset = DA9062_REG_EVENT_C_OFFSET,
+ .mask = DA9062AA_M_GPI4_MASK,
+ },
+};
+
+static struct regmap_irq_chip da9061_irq_chip = {
+ .name = "da9061-irq",
+ .irqs = da9061_irqs,
+ .num_irqs = DA9061_NUM_IRQ,
+ .num_regs = 3,
+ .status_base = DA9062AA_EVENT_A,
+ .mask_base = DA9062AA_IRQ_MASK_A,
+ .ack_base = DA9062AA_EVENT_A,
+};
+
static struct regmap_irq da9062_irqs[] = {
/* EVENT A */
[DA9062_IRQ_ONKEY] = {
@@ -102,6 +166,57 @@
.ack_base = DA9062AA_EVENT_A,
};
+static struct resource da9061_core_resources[] = {
+ DEFINE_RES_IRQ_NAMED(DA9061_IRQ_VDD_WARN, "VDD_WARN"),
+};
+
+static struct resource da9061_regulators_resources[] = {
+ DEFINE_RES_IRQ_NAMED(DA9061_IRQ_LDO_LIM, "LDO_LIM"),
+};
+
+static struct resource da9061_thermal_resources[] = {
+ DEFINE_RES_IRQ_NAMED(DA9061_IRQ_TEMP, "THERMAL"),
+};
+
+static struct resource da9061_wdt_resources[] = {
+ DEFINE_RES_IRQ_NAMED(DA9061_IRQ_WDG_WARN, "WD_WARN"),
+};
+
+static struct resource da9061_onkey_resources[] = {
+ DEFINE_RES_IRQ_NAMED(DA9061_IRQ_ONKEY, "ONKEY"),
+};
+
+static const struct mfd_cell da9061_devs[] = {
+ {
+ .name = "da9061-core",
+ .num_resources = ARRAY_SIZE(da9061_core_resources),
+ .resources = da9061_core_resources,
+ },
+ {
+ .name = "da9062-regulators",
+ .num_resources = ARRAY_SIZE(da9061_regulators_resources),
+ .resources = da9061_regulators_resources,
+ },
+ {
+ .name = "da9061-watchdog",
+ .num_resources = ARRAY_SIZE(da9061_wdt_resources),
+ .resources = da9061_wdt_resources,
+ .of_compatible = "dlg,da9061-watchdog",
+ },
+ {
+ .name = "da9061-thermal",
+ .num_resources = ARRAY_SIZE(da9061_thermal_resources),
+ .resources = da9061_thermal_resources,
+ .of_compatible = "dlg,da9061-thermal",
+ },
+ {
+ .name = "da9061-onkey",
+ .num_resources = ARRAY_SIZE(da9061_onkey_resources),
+ .resources = da9061_onkey_resources,
+ .of_compatible = "dlg,da9061-onkey",
+ },
+};
+
static struct resource da9062_core_resources[] = {
DEFINE_RES_NAMED(DA9062_IRQ_VDD_WARN, 1, "VDD_WARN", IORESOURCE_IRQ),
};
@@ -200,7 +315,8 @@ static int da9062_clear_fault_log(struct da9062 *chip)
static int da9062_get_device_type(struct da9062 *chip)
{
- int device_id, variant_id, variant_mrc;
+ int device_id, variant_id, variant_mrc, variant_vrc;
+ char *type;
int ret;
ret = regmap_read(chip->regmap, DA9062AA_DEVICE_ID, &device_id);
@@ -219,9 +335,23 @@ static int da9062_get_device_type(struct da9062 *chip)
return -EIO;
}
+ variant_vrc = (variant_id & DA9062AA_VRC_MASK) >> DA9062AA_VRC_SHIFT;
+
+ switch (variant_vrc) {
+ case DA9062_PMIC_VARIANT_VRC_DA9061:
+ type = "DA9061";
+ break;
+ case DA9062_PMIC_VARIANT_VRC_DA9062:
+ type = "DA9062";
+ break;
+ default:
+ type = "Unknown";
+ break;
+ }
+
dev_info(chip->dev,
- "Device detected (device-ID: 0x%02X, var-ID: 0x%02X)\n",
- device_id, variant_id);
+ "Device detected (device-ID: 0x%02X, var-ID: 0x%02X, %s)\n",
+ device_id, variant_id, type);
variant_mrc = (variant_id & DA9062AA_MRC_MASK) >> DA9062AA_MRC_SHIFT;
@@ -234,6 +364,234 @@ static int da9062_get_device_type(struct da9062 *chip)
return ret;
}
+static const struct regmap_range da9061_aa_readable_ranges[] = {
+ {
+ .range_min = DA9062AA_PAGE_CON,
+ .range_max = DA9062AA_STATUS_B,
+ }, {
+ .range_min = DA9062AA_STATUS_D,
+ .range_max = DA9062AA_EVENT_C,
+ }, {
+ .range_min = DA9062AA_IRQ_MASK_A,
+ .range_max = DA9062AA_IRQ_MASK_C,
+ }, {
+ .range_min = DA9062AA_CONTROL_A,
+ .range_max = DA9062AA_GPIO_4,
+ }, {
+ .range_min = DA9062AA_GPIO_WKUP_MODE,
+ .range_max = DA9062AA_GPIO_OUT3_4,
+ }, {
+ .range_min = DA9062AA_BUCK1_CONT,
+ .range_max = DA9062AA_BUCK4_CONT,
+ }, {
+ .range_min = DA9062AA_BUCK3_CONT,
+ .range_max = DA9062AA_BUCK3_CONT,
+ }, {
+ .range_min = DA9062AA_LDO1_CONT,
+ .range_max = DA9062AA_LDO4_CONT,
+ }, {
+ .range_min = DA9062AA_DVC_1,
+ .range_max = DA9062AA_DVC_1,
+ }, {
+ .range_min = DA9062AA_SEQ,
+ .range_max = DA9062AA_ID_4_3,
+ }, {
+ .range_min = DA9062AA_ID_12_11,
+ .range_max = DA9062AA_ID_16_15,
+ }, {
+ .range_min = DA9062AA_ID_22_21,
+ .range_max = DA9062AA_ID_32_31,
+ }, {
+ .range_min = DA9062AA_SEQ_A,
+ .range_max = DA9062AA_WAIT,
+ }, {
+ .range_min = DA9062AA_RESET,
+ .range_max = DA9062AA_BUCK_ILIM_C,
+ }, {
+ .range_min = DA9062AA_BUCK1_CFG,
+ .range_max = DA9062AA_BUCK3_CFG,
+ }, {
+ .range_min = DA9062AA_VBUCK1_A,
+ .range_max = DA9062AA_VBUCK4_A,
+ }, {
+ .range_min = DA9062AA_VBUCK3_A,
+ .range_max = DA9062AA_VBUCK3_A,
+ }, {
+ .range_min = DA9062AA_VLDO1_A,
+ .range_max = DA9062AA_VLDO4_A,
+ }, {
+ .range_min = DA9062AA_VBUCK1_B,
+ .range_max = DA9062AA_VBUCK4_B,
+ }, {
+ .range_min = DA9062AA_VBUCK3_B,
+ .range_max = DA9062AA_VBUCK3_B,
+ }, {
+ .range_min = DA9062AA_VLDO1_B,
+ .range_max = DA9062AA_VLDO4_B,
+ }, {
+ .range_min = DA9062AA_BBAT_CONT,
+ .range_max = DA9062AA_BBAT_CONT,
+ }, {
+ .range_min = DA9062AA_INTERFACE,
+ .range_max = DA9062AA_CONFIG_E,
+ }, {
+ .range_min = DA9062AA_CONFIG_G,
+ .range_max = DA9062AA_CONFIG_K,
+ }, {
+ .range_min = DA9062AA_CONFIG_M,
+ .range_max = DA9062AA_CONFIG_M,
+ }, {
+ .range_min = DA9062AA_GP_ID_0,
+ .range_max = DA9062AA_GP_ID_19,
+ }, {
+ .range_min = DA9062AA_DEVICE_ID,
+ .range_max = DA9062AA_CONFIG_ID,
+ },
+};
+
+static const struct regmap_range da9061_aa_writeable_ranges[] = {
+ {
+ .range_min = DA9062AA_PAGE_CON,
+ .range_max = DA9062AA_PAGE_CON,
+ }, {
+ .range_min = DA9062AA_FAULT_LOG,
+ .range_max = DA9062AA_EVENT_C,
+ }, {
+ .range_min = DA9062AA_IRQ_MASK_A,
+ .range_max = DA9062AA_IRQ_MASK_C,
+ }, {
+ .range_min = DA9062AA_CONTROL_A,
+ .range_max = DA9062AA_GPIO_4,
+ }, {
+ .range_min = DA9062AA_GPIO_WKUP_MODE,
+ .range_max = DA9062AA_GPIO_OUT3_4,
+ }, {
+ .range_min = DA9062AA_BUCK1_CONT,
+ .range_max = DA9062AA_BUCK4_CONT,
+ }, {
+ .range_min = DA9062AA_BUCK3_CONT,
+ .range_max = DA9062AA_BUCK3_CONT,
+ }, {
+ .range_min = DA9062AA_LDO1_CONT,
+ .range_max = DA9062AA_LDO4_CONT,
+ }, {
+ .range_min = DA9062AA_DVC_1,
+ .range_max = DA9062AA_DVC_1,
+ }, {
+ .range_min = DA9062AA_SEQ,
+ .range_max = DA9062AA_ID_4_3,
+ }, {
+ .range_min = DA9062AA_ID_12_11,
+ .range_max = DA9062AA_ID_16_15,
+ }, {
+ .range_min = DA9062AA_ID_22_21,
+ .range_max = DA9062AA_ID_32_31,
+ }, {
+ .range_min = DA9062AA_SEQ_A,
+ .range_max = DA9062AA_WAIT,
+ }, {
+ .range_min = DA9062AA_RESET,
+ .range_max = DA9062AA_BUCK_ILIM_C,
+ }, {
+ .range_min = DA9062AA_BUCK1_CFG,
+ .range_max = DA9062AA_BUCK3_CFG,
+ }, {
+ .range_min = DA9062AA_VBUCK1_A,
+ .range_max = DA9062AA_VBUCK4_A,
+ }, {
+ .range_min = DA9062AA_VBUCK3_A,
+ .range_max = DA9062AA_VBUCK3_A,
+ }, {
+ .range_min = DA9062AA_VLDO1_A,
+ .range_max = DA9062AA_VLDO4_A,
+ }, {
+ .range_min = DA9062AA_VBUCK1_B,
+ .range_max = DA9062AA_VBUCK4_B,
+ }, {
+ .range_min = DA9062AA_VBUCK3_B,
+ .range_max = DA9062AA_VBUCK3_B,
+ }, {
+ .range_min = DA9062AA_VLDO1_B,
+ .range_max = DA9062AA_VLDO4_B,
+ }, {
+ .range_min = DA9062AA_BBAT_CONT,
+ .range_max = DA9062AA_BBAT_CONT,
+ }, {
+ .range_min = DA9062AA_GP_ID_0,
+ .range_max = DA9062AA_GP_ID_19,
+ },
+};
+
+static const struct regmap_range da9061_aa_volatile_ranges[] = {
+ {
+ .range_min = DA9062AA_PAGE_CON,
+ .range_max = DA9062AA_STATUS_B,
+ }, {
+ .range_min = DA9062AA_STATUS_D,
+ .range_max = DA9062AA_EVENT_C,
+ }, {
+ .range_min = DA9062AA_CONTROL_A,
+ .range_max = DA9062AA_CONTROL_B,
+ }, {
+ .range_min = DA9062AA_CONTROL_E,
+ .range_max = DA9062AA_CONTROL_F,
+ }, {
+ .range_min = DA9062AA_BUCK1_CONT,
+ .range_max = DA9062AA_BUCK4_CONT,
+ }, {
+ .range_min = DA9062AA_BUCK3_CONT,
+ .range_max = DA9062AA_BUCK3_CONT,
+ }, {
+ .range_min = DA9062AA_LDO1_CONT,
+ .range_max = DA9062AA_LDO4_CONT,
+ }, {
+ .range_min = DA9062AA_DVC_1,
+ .range_max = DA9062AA_DVC_1,
+ }, {
+ .range_min = DA9062AA_SEQ,
+ .range_max = DA9062AA_SEQ,
+ },
+};
+
+static const struct regmap_access_table da9061_aa_readable_table = {
+ .yes_ranges = da9061_aa_readable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(da9061_aa_readable_ranges),
+};
+
+static const struct regmap_access_table da9061_aa_writeable_table = {
+ .yes_ranges = da9061_aa_writeable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(da9061_aa_writeable_ranges),
+};
+
+static const struct regmap_access_table da9061_aa_volatile_table = {
+ .yes_ranges = da9061_aa_volatile_ranges,
+ .n_yes_ranges = ARRAY_SIZE(da9061_aa_volatile_ranges),
+};
+
+static const struct regmap_range_cfg da9061_range_cfg[] = {
+ {
+ .range_min = DA9062AA_PAGE_CON,
+ .range_max = DA9062AA_CONFIG_ID,
+ .selector_reg = DA9062AA_PAGE_CON,
+ .selector_mask = 1 << DA9062_I2C_PAGE_SEL_SHIFT,
+ .selector_shift = DA9062_I2C_PAGE_SEL_SHIFT,
+ .window_start = 0,
+ .window_len = 256,
+ }
+};
+
+static struct regmap_config da9061_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .ranges = da9061_range_cfg,
+ .num_ranges = ARRAY_SIZE(da9061_range_cfg),
+ .max_register = DA9062AA_CONFIG_ID,
+ .cache_type = REGCACHE_RBTREE,
+ .rd_table = &da9061_aa_readable_table,
+ .wr_table = &da9061_aa_writeable_table,
+ .volatile_table = &da9061_aa_volatile_table,
+};
+
static const struct regmap_range da9062_aa_readable_ranges[] = {
{
.range_min = DA9062AA_PAGE_CON,
@@ -456,17 +814,39 @@ static int da9062_get_device_type(struct da9062 *chip)
.volatile_table = &da9062_aa_volatile_table,
};
+static const struct of_device_id da9062_dt_ids[] = {
+ { .compatible = "dlg,da9061", .data = (void *)COMPAT_TYPE_DA9061, },
+ { .compatible = "dlg,da9062", .data = (void *)COMPAT_TYPE_DA9062, },
+ { }
+};
+MODULE_DEVICE_TABLE(of, da9062_dt_ids);
+
static int da9062_i2c_probe(struct i2c_client *i2c,
const struct i2c_device_id *id)
{
struct da9062 *chip;
+ const struct of_device_id *match;
unsigned int irq_base;
+ const struct mfd_cell *cell;
+ const struct regmap_irq_chip *irq_chip;
+ const struct regmap_config *config;
+ int cell_num;
int ret;
chip = devm_kzalloc(&i2c->dev, sizeof(*chip), GFP_KERNEL);
if (!chip)
return -ENOMEM;
+ if (i2c->dev.of_node) {
+ match = of_match_node(da9062_dt_ids, i2c->dev.of_node);
+ if (!match)
+ return -EINVAL;
+
+ chip->chip_type = (uintptr_t)match->data;
+ } else {
+ chip->chip_type = id->driver_data;
+ }
+
i2c_set_clientdata(i2c, chip);
chip->dev = &i2c->dev;
@@ -475,7 +855,25 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
return -EINVAL;
}
- chip->regmap = devm_regmap_init_i2c(i2c, &da9062_regmap_config);
+ switch (chip->chip_type) {
+ case COMPAT_TYPE_DA9061:
+ cell = da9061_devs;
+ cell_num = ARRAY_SIZE(da9061_devs);
+ irq_chip = &da9061_irq_chip;
+ config = &da9061_regmap_config;
+ break;
+ case COMPAT_TYPE_DA9062:
+ cell = da9062_devs;
+ cell_num = ARRAY_SIZE(da9062_devs);
+ irq_chip = &da9062_irq_chip;
+ config = &da9062_regmap_config;
+ break;
+ default:
+ dev_err(chip->dev, "Unrecognised chip type\n");
+ return -ENODEV;
+ }
+
+ chip->regmap = devm_regmap_init_i2c(i2c, config);
if (IS_ERR(chip->regmap)) {
ret = PTR_ERR(chip->regmap);
dev_err(chip->dev, "Failed to allocate register map: %d\n",
@@ -493,7 +891,7 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
ret = regmap_add_irq_chip(chip->regmap, i2c->irq,
IRQF_TRIGGER_LOW | IRQF_ONESHOT | IRQF_SHARED,
- -1, &da9062_irq_chip,
+ -1, irq_chip,
&chip->regmap_irq);
if (ret) {
dev_err(chip->dev, "Failed to request IRQ %d: %d\n",
@@ -503,8 +901,8 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
irq_base = regmap_irq_chip_get_base(chip->regmap_irq);
- ret = mfd_add_devices(chip->dev, PLATFORM_DEVID_NONE, da9062_devs,
- ARRAY_SIZE(da9062_devs), NULL, irq_base,
+ ret = mfd_add_devices(chip->dev, PLATFORM_DEVID_NONE, cell,
+ cell_num, NULL, irq_base,
NULL);
if (ret) {
dev_err(chip->dev, "Cannot register child devices\n");
@@ -526,17 +924,12 @@ static int da9062_i2c_remove(struct i2c_client *i2c)
}
static const struct i2c_device_id da9062_i2c_id[] = {
- { "da9062", 0 },
+ { "da9061", COMPAT_TYPE_DA9061 },
+ { "da9062", COMPAT_TYPE_DA9062 },
{ },
};
MODULE_DEVICE_TABLE(i2c, da9062_i2c_id);
-static const struct of_device_id da9062_dt_ids[] = {
- { .compatible = "dlg,da9062", },
- { }
-};
-MODULE_DEVICE_TABLE(of, da9062_dt_ids);
-
static struct i2c_driver da9062_i2c_driver = {
.driver = {
.name = "da9062",
@@ -549,6 +942,6 @@ static int da9062_i2c_remove(struct i2c_client *i2c)
module_i2c_driver(da9062_i2c_driver);
-MODULE_DESCRIPTION("Core device driver for Dialog DA9062");
+MODULE_DESCRIPTION("Core device driver for Dialog DA9061 and DA9062");
MODULE_AUTHOR("Steve Twiss <stwiss.opensource@diasemi.com>");
MODULE_LICENSE("GPL");
diff --git a/include/linux/mfd/da9062/core.h b/include/linux/mfd/da9062/core.h
index 376ba84..74d33a0 100644
--- a/include/linux/mfd/da9062/core.h
+++ b/include/linux/mfd/da9062/core.h
@@ -1,5 +1,5 @@
/*
- * Copyright (C) 2015 Dialog Semiconductor Ltd.
+ * Copyright (C) 2015-2017 Dialog Semiconductor
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
@@ -18,7 +18,31 @@
#include <linux/interrupt.h>
#include <linux/mfd/da9062/registers.h>
-/* Interrupts */
+enum da9062_compatible_types {
+ COMPAT_TYPE_DA9061 = 1,
+ COMPAT_TYPE_DA9062,
+};
+
+enum da9061_irqs {
+ /* IRQ A */
+ DA9061_IRQ_ONKEY,
+ DA9061_IRQ_WDG_WARN,
+ DA9061_IRQ_SEQ_RDY,
+ /* IRQ B*/
+ DA9061_IRQ_TEMP,
+ DA9061_IRQ_LDO_LIM,
+ DA9061_IRQ_DVC_RDY,
+ DA9061_IRQ_VDD_WARN,
+ /* IRQ C */
+ DA9061_IRQ_GPI0,
+ DA9061_IRQ_GPI1,
+ DA9061_IRQ_GPI2,
+ DA9061_IRQ_GPI3,
+ DA9061_IRQ_GPI4,
+
+ DA9061_NUM_IRQ,
+};
+
enum da9062_irqs {
/* IRQ A */
DA9062_IRQ_ONKEY,
@@ -45,6 +69,7 @@ struct da9062 {
struct device *dev;
struct regmap *regmap;
struct regmap_irq_chip_data *regmap_irq;
+ enum da9062_compatible_types chip_type;
};
#endif /* __MFD_DA9062_CORE_H__ */
diff --git a/include/linux/mfd/da9062/registers.h b/include/linux/mfd/da9062/registers.h
index 97790d1..18d576a 100644
--- a/include/linux/mfd/da9062/registers.h
+++ b/include/linux/mfd/da9062/registers.h
@@ -1,6 +1,5 @@
/*
- * registers.h - REGISTERS H for DA9062
- * Copyright (C) 2015 Dialog Semiconductor Ltd.
+ * Copyright (C) 2015-2017 Dialog Semiconductor
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
@@ -18,6 +17,8 @@
#define DA9062_PMIC_DEVICE_ID 0x62
#define DA9062_PMIC_VARIANT_MRC_AA 0x01
+#define DA9062_PMIC_VARIANT_VRC_DA9061 0x01
+#define DA9062_PMIC_VARIANT_VRC_DA9062 0x02
#define DA9062_I2C_PAGE_SEL_SHIFT 1
--
end-of-patch for PATCH V7
^ permalink raw reply related [flat|nested] 36+ messages in thread* Re: [PATCH V7 4/7] mfd: da9061: MFD core support
2017-04-03 14:46 ` [PATCH V7 4/7] mfd: da9061: MFD core support Steve Twiss
@ 2017-04-04 8:39 ` Lee Jones
0 siblings, 0 replies; 36+ messages in thread
From: Lee Jones @ 2017-04-04 8:39 UTC (permalink / raw)
To: Steve Twiss
Cc: LINUX-KERNEL, DEVICETREE, Dmitry Torokhov, Eduardo Valentin,
Guenter Roeck, LINUX-INPUT, LINUX-PM, LINUX-WATCHDOG,
Liam Girdwood, Mark Brown, Mark Rutland, Rob Herring,
Support Opensource, Wim Van Sebroeck, Zhang Rui
On Mon, 03 Apr 2017, Steve Twiss wrote:
> From: Steve Twiss <stwiss.opensource@diasemi.com>
>
> MFD support for DA9061 is provided as part of the DA9062 device driver.
>
> The registers header file adds two new chip variant IDs defined in DA9061
> and DA9062 hardware. The core header file adds new software enumerations
> for listing the valid DA9061 IRQs and a da9062_compatible_types enumeration
> for distinguishing between DA9061/62 devices in software.
>
> The core source code adds a new .compatible of_device_id entry. This is
> extended from DA9062 to support both "dlg,da9061" and "dlg,da9062". The
> .data entry now holds a reference to the enumerated device type.
>
> A new regmap_irq_chip model is added for DA9061 and this supports the new
> list of regmap_irq entries. A new mfd_cell da9061_devs[] array lists the
> new sub system components for DA9061. Support is added for a new DA9061
> regmap_config which lists the correct readable, writable and volatile
> ranges for this chip.
>
> The probe function uses the device tree compatible string to switch on the
> da9062_compatible_types and configure the correct mfd cells, irq chip and
> regmap config.
>
> Kconfig is updated to reflect support for DA9061 and DA9062 PMICs.
>
> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Ah, here it is.
Applied, thanks.
> ---
> Acked-for-mfd-by: Lee Jones <lee.jones@linaro.org>
>
> Hi Lee, that Ack was from your earlier posting:
> https://lkml.org/lkml/2017/1/4/328 this was
> Regards, Steve.
>
> This patch applies against linux-next and v4.11-rc3
>
> v6 -> v7 + update
> - Removed brackets surrounding case statements for
> case COMPAT_TYPE_DA9061:
> case COMPAT_TYPE_DA9062:
>
> v6 -> v7
> - Remove compilation warning when casting a void * to an integer on
> ARCH=x86_64 using -Wpointer-to-int-cast.
> - Recommendation uintptr_t cast: https://lkml.org/lkml/2017/3/28/292
> - Compile tested ARCH=x86_64
>
> v5 -> v6
> - Rebased from v4.9 to v4.11-rc3
> - Modify Copyright to match Dialog latest legal statement
> - Fixed "braces {} should be used on all arms" checkpatch warning
>
> v4 -> v5
> - NO CODE CHANGE
> - Rebased from v4.8 to v4.9
>
> v3 -> v4
> - Patch renamed from [PATCH V3 5/9] to [PATCH V4 4/8]
> - Removed DEFINE_RES_NAMED() macros for DA9061 resources and replaced
> them with DEFINE_RES_IRQ_NAMED().
> - Removed whitespace
> - Reverted change for badly defined mfd_cell da9062_devs of_compatible
> string from "dlg,da9062-watchdog" back to "dlg,da9062-wdt"
>
> v2 -> v3
> - NO CODE CHANGE
> - Patch renamed from [PATCH V2 05/10] to [PATCH V3 5/9]
>
> v1 -> v2
> - Patch renamed from [PATCH V1 01/10] to [PATCH V2 05/10] -- these
> changes were made to fix checkpatch warnings caused by the patch
> set dependency order
> - Fixed typo in the commit message "readble" to "readable"
> - Removed the explicit cross-check to decide if there is a conflict
> between the device tree compatible string and the hardware definition.
> This patch assumes the device tree is correctly written and therefore
> removes the need for a hardware/DT sanity check.
> - Removed extra semicolon in drivers/mfd/da9062-core.c:877
> - Re-write compatible entries into numerical order
>
> Lee,
>
> Changes as described in the version history above.
>
> As previously:
> This patch adds support for the DA9061 PMIC. This is done as part of the
> existing DA9062 device driver by extending the of_device_id match table.
> This in turn allows new MFD cells, irq chip and regmap definitions to
> support DA9061.
>
> Regards,
> Steve Twiss, Dialog Semiconductor
>
>
> drivers/mfd/Kconfig | 5 +-
> drivers/mfd/da9062-core.c | 427 +++++++++++++++++++++++++++++++++--
> include/linux/mfd/da9062/core.h | 29 ++-
> include/linux/mfd/da9062/registers.h | 5 +-
> 4 files changed, 443 insertions(+), 23 deletions(-)
>
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index 55ecdfb..29cc11a 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -263,13 +263,14 @@ config MFD_DA9055
> called "da9055"
>
> config MFD_DA9062
> - tristate "Dialog Semiconductor DA9062 PMIC Support"
> + tristate "Dialog Semiconductor DA9062/61 PMIC Support"
> select MFD_CORE
> select REGMAP_I2C
> select REGMAP_IRQ
> depends on I2C
> help
> - Say yes here for support for the Dialog Semiconductor DA9062 PMIC.
> + Say yes here for support for the Dialog Semiconductor DA9061 and
> + DA9062 PMICs.
> This includes the I2C driver and core APIs.
> Additional drivers must be enabled in order to use the functionality
> of the device.
> diff --git a/drivers/mfd/da9062-core.c b/drivers/mfd/da9062-core.c
> index 8f873866..1803f58 100644
> --- a/drivers/mfd/da9062-core.c
> +++ b/drivers/mfd/da9062-core.c
> @@ -1,6 +1,6 @@
> /*
> - * Core, IRQ and I2C device driver for DA9062 PMIC
> - * Copyright (C) 2015 Dialog Semiconductor Ltd.
> + * Core, IRQ and I2C device driver for DA9061 and DA9062 PMICs
> + * Copyright (C) 2015-2017 Dialog Semiconductor
> *
> * This program is free software; you can redistribute it and/or
> * modify it under the terms of the GNU General Public License
> @@ -30,6 +30,70 @@
> #define DA9062_REG_EVENT_B_OFFSET 1
> #define DA9062_REG_EVENT_C_OFFSET 2
>
> +static struct regmap_irq da9061_irqs[] = {
> + /* EVENT A */
> + [DA9061_IRQ_ONKEY] = {
> + .reg_offset = DA9062_REG_EVENT_A_OFFSET,
> + .mask = DA9062AA_M_NONKEY_MASK,
> + },
> + [DA9061_IRQ_WDG_WARN] = {
> + .reg_offset = DA9062_REG_EVENT_A_OFFSET,
> + .mask = DA9062AA_M_WDG_WARN_MASK,
> + },
> + [DA9061_IRQ_SEQ_RDY] = {
> + .reg_offset = DA9062_REG_EVENT_A_OFFSET,
> + .mask = DA9062AA_M_SEQ_RDY_MASK,
> + },
> + /* EVENT B */
> + [DA9061_IRQ_TEMP] = {
> + .reg_offset = DA9062_REG_EVENT_B_OFFSET,
> + .mask = DA9062AA_M_TEMP_MASK,
> + },
> + [DA9061_IRQ_LDO_LIM] = {
> + .reg_offset = DA9062_REG_EVENT_B_OFFSET,
> + .mask = DA9062AA_M_LDO_LIM_MASK,
> + },
> + [DA9061_IRQ_DVC_RDY] = {
> + .reg_offset = DA9062_REG_EVENT_B_OFFSET,
> + .mask = DA9062AA_M_DVC_RDY_MASK,
> + },
> + [DA9061_IRQ_VDD_WARN] = {
> + .reg_offset = DA9062_REG_EVENT_B_OFFSET,
> + .mask = DA9062AA_M_VDD_WARN_MASK,
> + },
> + /* EVENT C */
> + [DA9061_IRQ_GPI0] = {
> + .reg_offset = DA9062_REG_EVENT_C_OFFSET,
> + .mask = DA9062AA_M_GPI0_MASK,
> + },
> + [DA9061_IRQ_GPI1] = {
> + .reg_offset = DA9062_REG_EVENT_C_OFFSET,
> + .mask = DA9062AA_M_GPI1_MASK,
> + },
> + [DA9061_IRQ_GPI2] = {
> + .reg_offset = DA9062_REG_EVENT_C_OFFSET,
> + .mask = DA9062AA_M_GPI2_MASK,
> + },
> + [DA9061_IRQ_GPI3] = {
> + .reg_offset = DA9062_REG_EVENT_C_OFFSET,
> + .mask = DA9062AA_M_GPI3_MASK,
> + },
> + [DA9061_IRQ_GPI4] = {
> + .reg_offset = DA9062_REG_EVENT_C_OFFSET,
> + .mask = DA9062AA_M_GPI4_MASK,
> + },
> +};
> +
> +static struct regmap_irq_chip da9061_irq_chip = {
> + .name = "da9061-irq",
> + .irqs = da9061_irqs,
> + .num_irqs = DA9061_NUM_IRQ,
> + .num_regs = 3,
> + .status_base = DA9062AA_EVENT_A,
> + .mask_base = DA9062AA_IRQ_MASK_A,
> + .ack_base = DA9062AA_EVENT_A,
> +};
> +
> static struct regmap_irq da9062_irqs[] = {
> /* EVENT A */
> [DA9062_IRQ_ONKEY] = {
> @@ -102,6 +166,57 @@
> .ack_base = DA9062AA_EVENT_A,
> };
>
> +static struct resource da9061_core_resources[] = {
> + DEFINE_RES_IRQ_NAMED(DA9061_IRQ_VDD_WARN, "VDD_WARN"),
> +};
> +
> +static struct resource da9061_regulators_resources[] = {
> + DEFINE_RES_IRQ_NAMED(DA9061_IRQ_LDO_LIM, "LDO_LIM"),
> +};
> +
> +static struct resource da9061_thermal_resources[] = {
> + DEFINE_RES_IRQ_NAMED(DA9061_IRQ_TEMP, "THERMAL"),
> +};
> +
> +static struct resource da9061_wdt_resources[] = {
> + DEFINE_RES_IRQ_NAMED(DA9061_IRQ_WDG_WARN, "WD_WARN"),
> +};
> +
> +static struct resource da9061_onkey_resources[] = {
> + DEFINE_RES_IRQ_NAMED(DA9061_IRQ_ONKEY, "ONKEY"),
> +};
> +
> +static const struct mfd_cell da9061_devs[] = {
> + {
> + .name = "da9061-core",
> + .num_resources = ARRAY_SIZE(da9061_core_resources),
> + .resources = da9061_core_resources,
> + },
> + {
> + .name = "da9062-regulators",
> + .num_resources = ARRAY_SIZE(da9061_regulators_resources),
> + .resources = da9061_regulators_resources,
> + },
> + {
> + .name = "da9061-watchdog",
> + .num_resources = ARRAY_SIZE(da9061_wdt_resources),
> + .resources = da9061_wdt_resources,
> + .of_compatible = "dlg,da9061-watchdog",
> + },
> + {
> + .name = "da9061-thermal",
> + .num_resources = ARRAY_SIZE(da9061_thermal_resources),
> + .resources = da9061_thermal_resources,
> + .of_compatible = "dlg,da9061-thermal",
> + },
> + {
> + .name = "da9061-onkey",
> + .num_resources = ARRAY_SIZE(da9061_onkey_resources),
> + .resources = da9061_onkey_resources,
> + .of_compatible = "dlg,da9061-onkey",
> + },
> +};
> +
> static struct resource da9062_core_resources[] = {
> DEFINE_RES_NAMED(DA9062_IRQ_VDD_WARN, 1, "VDD_WARN", IORESOURCE_IRQ),
> };
> @@ -200,7 +315,8 @@ static int da9062_clear_fault_log(struct da9062 *chip)
>
> static int da9062_get_device_type(struct da9062 *chip)
> {
> - int device_id, variant_id, variant_mrc;
> + int device_id, variant_id, variant_mrc, variant_vrc;
> + char *type;
> int ret;
>
> ret = regmap_read(chip->regmap, DA9062AA_DEVICE_ID, &device_id);
> @@ -219,9 +335,23 @@ static int da9062_get_device_type(struct da9062 *chip)
> return -EIO;
> }
>
> + variant_vrc = (variant_id & DA9062AA_VRC_MASK) >> DA9062AA_VRC_SHIFT;
> +
> + switch (variant_vrc) {
> + case DA9062_PMIC_VARIANT_VRC_DA9061:
> + type = "DA9061";
> + break;
> + case DA9062_PMIC_VARIANT_VRC_DA9062:
> + type = "DA9062";
> + break;
> + default:
> + type = "Unknown";
> + break;
> + }
> +
> dev_info(chip->dev,
> - "Device detected (device-ID: 0x%02X, var-ID: 0x%02X)\n",
> - device_id, variant_id);
> + "Device detected (device-ID: 0x%02X, var-ID: 0x%02X, %s)\n",
> + device_id, variant_id, type);
>
> variant_mrc = (variant_id & DA9062AA_MRC_MASK) >> DA9062AA_MRC_SHIFT;
>
> @@ -234,6 +364,234 @@ static int da9062_get_device_type(struct da9062 *chip)
> return ret;
> }
>
> +static const struct regmap_range da9061_aa_readable_ranges[] = {
> + {
> + .range_min = DA9062AA_PAGE_CON,
> + .range_max = DA9062AA_STATUS_B,
> + }, {
> + .range_min = DA9062AA_STATUS_D,
> + .range_max = DA9062AA_EVENT_C,
> + }, {
> + .range_min = DA9062AA_IRQ_MASK_A,
> + .range_max = DA9062AA_IRQ_MASK_C,
> + }, {
> + .range_min = DA9062AA_CONTROL_A,
> + .range_max = DA9062AA_GPIO_4,
> + }, {
> + .range_min = DA9062AA_GPIO_WKUP_MODE,
> + .range_max = DA9062AA_GPIO_OUT3_4,
> + }, {
> + .range_min = DA9062AA_BUCK1_CONT,
> + .range_max = DA9062AA_BUCK4_CONT,
> + }, {
> + .range_min = DA9062AA_BUCK3_CONT,
> + .range_max = DA9062AA_BUCK3_CONT,
> + }, {
> + .range_min = DA9062AA_LDO1_CONT,
> + .range_max = DA9062AA_LDO4_CONT,
> + }, {
> + .range_min = DA9062AA_DVC_1,
> + .range_max = DA9062AA_DVC_1,
> + }, {
> + .range_min = DA9062AA_SEQ,
> + .range_max = DA9062AA_ID_4_3,
> + }, {
> + .range_min = DA9062AA_ID_12_11,
> + .range_max = DA9062AA_ID_16_15,
> + }, {
> + .range_min = DA9062AA_ID_22_21,
> + .range_max = DA9062AA_ID_32_31,
> + }, {
> + .range_min = DA9062AA_SEQ_A,
> + .range_max = DA9062AA_WAIT,
> + }, {
> + .range_min = DA9062AA_RESET,
> + .range_max = DA9062AA_BUCK_ILIM_C,
> + }, {
> + .range_min = DA9062AA_BUCK1_CFG,
> + .range_max = DA9062AA_BUCK3_CFG,
> + }, {
> + .range_min = DA9062AA_VBUCK1_A,
> + .range_max = DA9062AA_VBUCK4_A,
> + }, {
> + .range_min = DA9062AA_VBUCK3_A,
> + .range_max = DA9062AA_VBUCK3_A,
> + }, {
> + .range_min = DA9062AA_VLDO1_A,
> + .range_max = DA9062AA_VLDO4_A,
> + }, {
> + .range_min = DA9062AA_VBUCK1_B,
> + .range_max = DA9062AA_VBUCK4_B,
> + }, {
> + .range_min = DA9062AA_VBUCK3_B,
> + .range_max = DA9062AA_VBUCK3_B,
> + }, {
> + .range_min = DA9062AA_VLDO1_B,
> + .range_max = DA9062AA_VLDO4_B,
> + }, {
> + .range_min = DA9062AA_BBAT_CONT,
> + .range_max = DA9062AA_BBAT_CONT,
> + }, {
> + .range_min = DA9062AA_INTERFACE,
> + .range_max = DA9062AA_CONFIG_E,
> + }, {
> + .range_min = DA9062AA_CONFIG_G,
> + .range_max = DA9062AA_CONFIG_K,
> + }, {
> + .range_min = DA9062AA_CONFIG_M,
> + .range_max = DA9062AA_CONFIG_M,
> + }, {
> + .range_min = DA9062AA_GP_ID_0,
> + .range_max = DA9062AA_GP_ID_19,
> + }, {
> + .range_min = DA9062AA_DEVICE_ID,
> + .range_max = DA9062AA_CONFIG_ID,
> + },
> +};
> +
> +static const struct regmap_range da9061_aa_writeable_ranges[] = {
> + {
> + .range_min = DA9062AA_PAGE_CON,
> + .range_max = DA9062AA_PAGE_CON,
> + }, {
> + .range_min = DA9062AA_FAULT_LOG,
> + .range_max = DA9062AA_EVENT_C,
> + }, {
> + .range_min = DA9062AA_IRQ_MASK_A,
> + .range_max = DA9062AA_IRQ_MASK_C,
> + }, {
> + .range_min = DA9062AA_CONTROL_A,
> + .range_max = DA9062AA_GPIO_4,
> + }, {
> + .range_min = DA9062AA_GPIO_WKUP_MODE,
> + .range_max = DA9062AA_GPIO_OUT3_4,
> + }, {
> + .range_min = DA9062AA_BUCK1_CONT,
> + .range_max = DA9062AA_BUCK4_CONT,
> + }, {
> + .range_min = DA9062AA_BUCK3_CONT,
> + .range_max = DA9062AA_BUCK3_CONT,
> + }, {
> + .range_min = DA9062AA_LDO1_CONT,
> + .range_max = DA9062AA_LDO4_CONT,
> + }, {
> + .range_min = DA9062AA_DVC_1,
> + .range_max = DA9062AA_DVC_1,
> + }, {
> + .range_min = DA9062AA_SEQ,
> + .range_max = DA9062AA_ID_4_3,
> + }, {
> + .range_min = DA9062AA_ID_12_11,
> + .range_max = DA9062AA_ID_16_15,
> + }, {
> + .range_min = DA9062AA_ID_22_21,
> + .range_max = DA9062AA_ID_32_31,
> + }, {
> + .range_min = DA9062AA_SEQ_A,
> + .range_max = DA9062AA_WAIT,
> + }, {
> + .range_min = DA9062AA_RESET,
> + .range_max = DA9062AA_BUCK_ILIM_C,
> + }, {
> + .range_min = DA9062AA_BUCK1_CFG,
> + .range_max = DA9062AA_BUCK3_CFG,
> + }, {
> + .range_min = DA9062AA_VBUCK1_A,
> + .range_max = DA9062AA_VBUCK4_A,
> + }, {
> + .range_min = DA9062AA_VBUCK3_A,
> + .range_max = DA9062AA_VBUCK3_A,
> + }, {
> + .range_min = DA9062AA_VLDO1_A,
> + .range_max = DA9062AA_VLDO4_A,
> + }, {
> + .range_min = DA9062AA_VBUCK1_B,
> + .range_max = DA9062AA_VBUCK4_B,
> + }, {
> + .range_min = DA9062AA_VBUCK3_B,
> + .range_max = DA9062AA_VBUCK3_B,
> + }, {
> + .range_min = DA9062AA_VLDO1_B,
> + .range_max = DA9062AA_VLDO4_B,
> + }, {
> + .range_min = DA9062AA_BBAT_CONT,
> + .range_max = DA9062AA_BBAT_CONT,
> + }, {
> + .range_min = DA9062AA_GP_ID_0,
> + .range_max = DA9062AA_GP_ID_19,
> + },
> +};
> +
> +static const struct regmap_range da9061_aa_volatile_ranges[] = {
> + {
> + .range_min = DA9062AA_PAGE_CON,
> + .range_max = DA9062AA_STATUS_B,
> + }, {
> + .range_min = DA9062AA_STATUS_D,
> + .range_max = DA9062AA_EVENT_C,
> + }, {
> + .range_min = DA9062AA_CONTROL_A,
> + .range_max = DA9062AA_CONTROL_B,
> + }, {
> + .range_min = DA9062AA_CONTROL_E,
> + .range_max = DA9062AA_CONTROL_F,
> + }, {
> + .range_min = DA9062AA_BUCK1_CONT,
> + .range_max = DA9062AA_BUCK4_CONT,
> + }, {
> + .range_min = DA9062AA_BUCK3_CONT,
> + .range_max = DA9062AA_BUCK3_CONT,
> + }, {
> + .range_min = DA9062AA_LDO1_CONT,
> + .range_max = DA9062AA_LDO4_CONT,
> + }, {
> + .range_min = DA9062AA_DVC_1,
> + .range_max = DA9062AA_DVC_1,
> + }, {
> + .range_min = DA9062AA_SEQ,
> + .range_max = DA9062AA_SEQ,
> + },
> +};
> +
> +static const struct regmap_access_table da9061_aa_readable_table = {
> + .yes_ranges = da9061_aa_readable_ranges,
> + .n_yes_ranges = ARRAY_SIZE(da9061_aa_readable_ranges),
> +};
> +
> +static const struct regmap_access_table da9061_aa_writeable_table = {
> + .yes_ranges = da9061_aa_writeable_ranges,
> + .n_yes_ranges = ARRAY_SIZE(da9061_aa_writeable_ranges),
> +};
> +
> +static const struct regmap_access_table da9061_aa_volatile_table = {
> + .yes_ranges = da9061_aa_volatile_ranges,
> + .n_yes_ranges = ARRAY_SIZE(da9061_aa_volatile_ranges),
> +};
> +
> +static const struct regmap_range_cfg da9061_range_cfg[] = {
> + {
> + .range_min = DA9062AA_PAGE_CON,
> + .range_max = DA9062AA_CONFIG_ID,
> + .selector_reg = DA9062AA_PAGE_CON,
> + .selector_mask = 1 << DA9062_I2C_PAGE_SEL_SHIFT,
> + .selector_shift = DA9062_I2C_PAGE_SEL_SHIFT,
> + .window_start = 0,
> + .window_len = 256,
> + }
> +};
> +
> +static struct regmap_config da9061_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + .ranges = da9061_range_cfg,
> + .num_ranges = ARRAY_SIZE(da9061_range_cfg),
> + .max_register = DA9062AA_CONFIG_ID,
> + .cache_type = REGCACHE_RBTREE,
> + .rd_table = &da9061_aa_readable_table,
> + .wr_table = &da9061_aa_writeable_table,
> + .volatile_table = &da9061_aa_volatile_table,
> +};
> +
> static const struct regmap_range da9062_aa_readable_ranges[] = {
> {
> .range_min = DA9062AA_PAGE_CON,
> @@ -456,17 +814,39 @@ static int da9062_get_device_type(struct da9062 *chip)
> .volatile_table = &da9062_aa_volatile_table,
> };
>
> +static const struct of_device_id da9062_dt_ids[] = {
> + { .compatible = "dlg,da9061", .data = (void *)COMPAT_TYPE_DA9061, },
> + { .compatible = "dlg,da9062", .data = (void *)COMPAT_TYPE_DA9062, },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, da9062_dt_ids);
> +
> static int da9062_i2c_probe(struct i2c_client *i2c,
> const struct i2c_device_id *id)
> {
> struct da9062 *chip;
> + const struct of_device_id *match;
> unsigned int irq_base;
> + const struct mfd_cell *cell;
> + const struct regmap_irq_chip *irq_chip;
> + const struct regmap_config *config;
> + int cell_num;
> int ret;
>
> chip = devm_kzalloc(&i2c->dev, sizeof(*chip), GFP_KERNEL);
> if (!chip)
> return -ENOMEM;
>
> + if (i2c->dev.of_node) {
> + match = of_match_node(da9062_dt_ids, i2c->dev.of_node);
> + if (!match)
> + return -EINVAL;
> +
> + chip->chip_type = (uintptr_t)match->data;
> + } else {
> + chip->chip_type = id->driver_data;
> + }
> +
> i2c_set_clientdata(i2c, chip);
> chip->dev = &i2c->dev;
>
> @@ -475,7 +855,25 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
> return -EINVAL;
> }
>
> - chip->regmap = devm_regmap_init_i2c(i2c, &da9062_regmap_config);
> + switch (chip->chip_type) {
> + case COMPAT_TYPE_DA9061:
> + cell = da9061_devs;
> + cell_num = ARRAY_SIZE(da9061_devs);
> + irq_chip = &da9061_irq_chip;
> + config = &da9061_regmap_config;
> + break;
> + case COMPAT_TYPE_DA9062:
> + cell = da9062_devs;
> + cell_num = ARRAY_SIZE(da9062_devs);
> + irq_chip = &da9062_irq_chip;
> + config = &da9062_regmap_config;
> + break;
> + default:
> + dev_err(chip->dev, "Unrecognised chip type\n");
> + return -ENODEV;
> + }
> +
> + chip->regmap = devm_regmap_init_i2c(i2c, config);
> if (IS_ERR(chip->regmap)) {
> ret = PTR_ERR(chip->regmap);
> dev_err(chip->dev, "Failed to allocate register map: %d\n",
> @@ -493,7 +891,7 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
>
> ret = regmap_add_irq_chip(chip->regmap, i2c->irq,
> IRQF_TRIGGER_LOW | IRQF_ONESHOT | IRQF_SHARED,
> - -1, &da9062_irq_chip,
> + -1, irq_chip,
> &chip->regmap_irq);
> if (ret) {
> dev_err(chip->dev, "Failed to request IRQ %d: %d\n",
> @@ -503,8 +901,8 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
>
> irq_base = regmap_irq_chip_get_base(chip->regmap_irq);
>
> - ret = mfd_add_devices(chip->dev, PLATFORM_DEVID_NONE, da9062_devs,
> - ARRAY_SIZE(da9062_devs), NULL, irq_base,
> + ret = mfd_add_devices(chip->dev, PLATFORM_DEVID_NONE, cell,
> + cell_num, NULL, irq_base,
> NULL);
> if (ret) {
> dev_err(chip->dev, "Cannot register child devices\n");
> @@ -526,17 +924,12 @@ static int da9062_i2c_remove(struct i2c_client *i2c)
> }
>
> static const struct i2c_device_id da9062_i2c_id[] = {
> - { "da9062", 0 },
> + { "da9061", COMPAT_TYPE_DA9061 },
> + { "da9062", COMPAT_TYPE_DA9062 },
> { },
> };
> MODULE_DEVICE_TABLE(i2c, da9062_i2c_id);
>
> -static const struct of_device_id da9062_dt_ids[] = {
> - { .compatible = "dlg,da9062", },
> - { }
> -};
> -MODULE_DEVICE_TABLE(of, da9062_dt_ids);
> -
> static struct i2c_driver da9062_i2c_driver = {
> .driver = {
> .name = "da9062",
> @@ -549,6 +942,6 @@ static int da9062_i2c_remove(struct i2c_client *i2c)
>
> module_i2c_driver(da9062_i2c_driver);
>
> -MODULE_DESCRIPTION("Core device driver for Dialog DA9062");
> +MODULE_DESCRIPTION("Core device driver for Dialog DA9061 and DA9062");
> MODULE_AUTHOR("Steve Twiss <stwiss.opensource@diasemi.com>");
> MODULE_LICENSE("GPL");
> diff --git a/include/linux/mfd/da9062/core.h b/include/linux/mfd/da9062/core.h
> index 376ba84..74d33a0 100644
> --- a/include/linux/mfd/da9062/core.h
> +++ b/include/linux/mfd/da9062/core.h
> @@ -1,5 +1,5 @@
> /*
> - * Copyright (C) 2015 Dialog Semiconductor Ltd.
> + * Copyright (C) 2015-2017 Dialog Semiconductor
> *
> * This program is free software; you can redistribute it and/or
> * modify it under the terms of the GNU General Public License
> @@ -18,7 +18,31 @@
> #include <linux/interrupt.h>
> #include <linux/mfd/da9062/registers.h>
>
> -/* Interrupts */
> +enum da9062_compatible_types {
> + COMPAT_TYPE_DA9061 = 1,
> + COMPAT_TYPE_DA9062,
> +};
> +
> +enum da9061_irqs {
> + /* IRQ A */
> + DA9061_IRQ_ONKEY,
> + DA9061_IRQ_WDG_WARN,
> + DA9061_IRQ_SEQ_RDY,
> + /* IRQ B*/
> + DA9061_IRQ_TEMP,
> + DA9061_IRQ_LDO_LIM,
> + DA9061_IRQ_DVC_RDY,
> + DA9061_IRQ_VDD_WARN,
> + /* IRQ C */
> + DA9061_IRQ_GPI0,
> + DA9061_IRQ_GPI1,
> + DA9061_IRQ_GPI2,
> + DA9061_IRQ_GPI3,
> + DA9061_IRQ_GPI4,
> +
> + DA9061_NUM_IRQ,
> +};
> +
> enum da9062_irqs {
> /* IRQ A */
> DA9062_IRQ_ONKEY,
> @@ -45,6 +69,7 @@ struct da9062 {
> struct device *dev;
> struct regmap *regmap;
> struct regmap_irq_chip_data *regmap_irq;
> + enum da9062_compatible_types chip_type;
> };
>
> #endif /* __MFD_DA9062_CORE_H__ */
> diff --git a/include/linux/mfd/da9062/registers.h b/include/linux/mfd/da9062/registers.h
> index 97790d1..18d576a 100644
> --- a/include/linux/mfd/da9062/registers.h
> +++ b/include/linux/mfd/da9062/registers.h
> @@ -1,6 +1,5 @@
> /*
> - * registers.h - REGISTERS H for DA9062
> - * Copyright (C) 2015 Dialog Semiconductor Ltd.
> + * Copyright (C) 2015-2017 Dialog Semiconductor
> *
> * This program is free software; you can redistribute it and/or
> * modify it under the terms of the GNU General Public License
> @@ -18,6 +17,8 @@
>
> #define DA9062_PMIC_DEVICE_ID 0x62
> #define DA9062_PMIC_VARIANT_MRC_AA 0x01
> +#define DA9062_PMIC_VARIANT_VRC_DA9061 0x01
> +#define DA9062_PMIC_VARIANT_VRC_DA9062 0x02
>
> #define DA9062_I2C_PAGE_SEL_SHIFT 1
>
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 36+ messages in thread* Re: [PATCH V7 4/7] mfd: da9061: MFD core support
@ 2017-04-04 8:39 ` Lee Jones
0 siblings, 0 replies; 36+ messages in thread
From: Lee Jones @ 2017-04-04 8:39 UTC (permalink / raw)
To: Steve Twiss
Cc: LINUX-KERNEL, DEVICETREE, Dmitry Torokhov, Eduardo Valentin,
Guenter Roeck, LINUX-INPUT, LINUX-PM, LINUX-WATCHDOG,
Liam Girdwood, Mark Brown, Mark Rutland, Rob Herring,
Support Opensource, Wim Van Sebroeck, Zhang Rui
On Mon, 03 Apr 2017, Steve Twiss wrote:
> From: Steve Twiss <stwiss.opensource@diasemi.com>
>
> MFD support for DA9061 is provided as part of the DA9062 device driver.
>
> The registers header file adds two new chip variant IDs defined in DA9061
> and DA9062 hardware. The core header file adds new software enumerations
> for listing the valid DA9061 IRQs and a da9062_compatible_types enumeration
> for distinguishing between DA9061/62 devices in software.
>
> The core source code adds a new .compatible of_device_id entry. This is
> extended from DA9062 to support both "dlg,da9061" and "dlg,da9062". The
> .data entry now holds a reference to the enumerated device type.
>
> A new regmap_irq_chip model is added for DA9061 and this supports the new
> list of regmap_irq entries. A new mfd_cell da9061_devs[] array lists the
> new sub system components for DA9061. Support is added for a new DA9061
> regmap_config which lists the correct readable, writable and volatile
> ranges for this chip.
>
> The probe function uses the device tree compatible string to switch on the
> da9062_compatible_types and configure the correct mfd cells, irq chip and
> regmap config.
>
> Kconfig is updated to reflect support for DA9061 and DA9062 PMICs.
>
> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Ah, here it is.
Applied, thanks.
> ---
> Acked-for-mfd-by: Lee Jones <lee.jones@linaro.org>
>
> Hi Lee, that Ack was from your earlier posting:
> https://lkml.org/lkml/2017/1/4/328 this was
> Regards, Steve.
>
> This patch applies against linux-next and v4.11-rc3
>
> v6 -> v7 + update
> - Removed brackets surrounding case statements for
> case COMPAT_TYPE_DA9061:
> case COMPAT_TYPE_DA9062:
>
> v6 -> v7
> - Remove compilation warning when casting a void * to an integer on
> ARCH=x86_64 using -Wpointer-to-int-cast.
> - Recommendation uintptr_t cast: https://lkml.org/lkml/2017/3/28/292
> - Compile tested ARCH=x86_64
>
> v5 -> v6
> - Rebased from v4.9 to v4.11-rc3
> - Modify Copyright to match Dialog latest legal statement
> - Fixed "braces {} should be used on all arms" checkpatch warning
>
> v4 -> v5
> - NO CODE CHANGE
> - Rebased from v4.8 to v4.9
>
> v3 -> v4
> - Patch renamed from [PATCH V3 5/9] to [PATCH V4 4/8]
> - Removed DEFINE_RES_NAMED() macros for DA9061 resources and replaced
> them with DEFINE_RES_IRQ_NAMED().
> - Removed whitespace
> - Reverted change for badly defined mfd_cell da9062_devs of_compatible
> string from "dlg,da9062-watchdog" back to "dlg,da9062-wdt"
>
> v2 -> v3
> - NO CODE CHANGE
> - Patch renamed from [PATCH V2 05/10] to [PATCH V3 5/9]
>
> v1 -> v2
> - Patch renamed from [PATCH V1 01/10] to [PATCH V2 05/10] -- these
> changes were made to fix checkpatch warnings caused by the patch
> set dependency order
> - Fixed typo in the commit message "readble" to "readable"
> - Removed the explicit cross-check to decide if there is a conflict
> between the device tree compatible string and the hardware definition.
> This patch assumes the device tree is correctly written and therefore
> removes the need for a hardware/DT sanity check.
> - Removed extra semicolon in drivers/mfd/da9062-core.c:877
> - Re-write compatible entries into numerical order
>
> Lee,
>
> Changes as described in the version history above.
>
> As previously:
> This patch adds support for the DA9061 PMIC. This is done as part of the
> existing DA9062 device driver by extending the of_device_id match table.
> This in turn allows new MFD cells, irq chip and regmap definitions to
> support DA9061.
>
> Regards,
> Steve Twiss, Dialog Semiconductor
>
>
> drivers/mfd/Kconfig | 5 +-
> drivers/mfd/da9062-core.c | 427 +++++++++++++++++++++++++++++++++--
> include/linux/mfd/da9062/core.h | 29 ++-
> include/linux/mfd/da9062/registers.h | 5 +-
> 4 files changed, 443 insertions(+), 23 deletions(-)
>
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index 55ecdfb..29cc11a 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -263,13 +263,14 @@ config MFD_DA9055
> called "da9055"
>
> config MFD_DA9062
> - tristate "Dialog Semiconductor DA9062 PMIC Support"
> + tristate "Dialog Semiconductor DA9062/61 PMIC Support"
> select MFD_CORE
> select REGMAP_I2C
> select REGMAP_IRQ
> depends on I2C
> help
> - Say yes here for support for the Dialog Semiconductor DA9062 PMIC.
> + Say yes here for support for the Dialog Semiconductor DA9061 and
> + DA9062 PMICs.
> This includes the I2C driver and core APIs.
> Additional drivers must be enabled in order to use the functionality
> of the device.
> diff --git a/drivers/mfd/da9062-core.c b/drivers/mfd/da9062-core.c
> index 8f873866..1803f58 100644
> --- a/drivers/mfd/da9062-core.c
> +++ b/drivers/mfd/da9062-core.c
> @@ -1,6 +1,6 @@
> /*
> - * Core, IRQ and I2C device driver for DA9062 PMIC
> - * Copyright (C) 2015 Dialog Semiconductor Ltd.
> + * Core, IRQ and I2C device driver for DA9061 and DA9062 PMICs
> + * Copyright (C) 2015-2017 Dialog Semiconductor
> *
> * This program is free software; you can redistribute it and/or
> * modify it under the terms of the GNU General Public License
> @@ -30,6 +30,70 @@
> #define DA9062_REG_EVENT_B_OFFSET 1
> #define DA9062_REG_EVENT_C_OFFSET 2
>
> +static struct regmap_irq da9061_irqs[] = {
> + /* EVENT A */
> + [DA9061_IRQ_ONKEY] = {
> + .reg_offset = DA9062_REG_EVENT_A_OFFSET,
> + .mask = DA9062AA_M_NONKEY_MASK,
> + },
> + [DA9061_IRQ_WDG_WARN] = {
> + .reg_offset = DA9062_REG_EVENT_A_OFFSET,
> + .mask = DA9062AA_M_WDG_WARN_MASK,
> + },
> + [DA9061_IRQ_SEQ_RDY] = {
> + .reg_offset = DA9062_REG_EVENT_A_OFFSET,
> + .mask = DA9062AA_M_SEQ_RDY_MASK,
> + },
> + /* EVENT B */
> + [DA9061_IRQ_TEMP] = {
> + .reg_offset = DA9062_REG_EVENT_B_OFFSET,
> + .mask = DA9062AA_M_TEMP_MASK,
> + },
> + [DA9061_IRQ_LDO_LIM] = {
> + .reg_offset = DA9062_REG_EVENT_B_OFFSET,
> + .mask = DA9062AA_M_LDO_LIM_MASK,
> + },
> + [DA9061_IRQ_DVC_RDY] = {
> + .reg_offset = DA9062_REG_EVENT_B_OFFSET,
> + .mask = DA9062AA_M_DVC_RDY_MASK,
> + },
> + [DA9061_IRQ_VDD_WARN] = {
> + .reg_offset = DA9062_REG_EVENT_B_OFFSET,
> + .mask = DA9062AA_M_VDD_WARN_MASK,
> + },
> + /* EVENT C */
> + [DA9061_IRQ_GPI0] = {
> + .reg_offset = DA9062_REG_EVENT_C_OFFSET,
> + .mask = DA9062AA_M_GPI0_MASK,
> + },
> + [DA9061_IRQ_GPI1] = {
> + .reg_offset = DA9062_REG_EVENT_C_OFFSET,
> + .mask = DA9062AA_M_GPI1_MASK,
> + },
> + [DA9061_IRQ_GPI2] = {
> + .reg_offset = DA9062_REG_EVENT_C_OFFSET,
> + .mask = DA9062AA_M_GPI2_MASK,
> + },
> + [DA9061_IRQ_GPI3] = {
> + .reg_offset = DA9062_REG_EVENT_C_OFFSET,
> + .mask = DA9062AA_M_GPI3_MASK,
> + },
> + [DA9061_IRQ_GPI4] = {
> + .reg_offset = DA9062_REG_EVENT_C_OFFSET,
> + .mask = DA9062AA_M_GPI4_MASK,
> + },
> +};
> +
> +static struct regmap_irq_chip da9061_irq_chip = {
> + .name = "da9061-irq",
> + .irqs = da9061_irqs,
> + .num_irqs = DA9061_NUM_IRQ,
> + .num_regs = 3,
> + .status_base = DA9062AA_EVENT_A,
> + .mask_base = DA9062AA_IRQ_MASK_A,
> + .ack_base = DA9062AA_EVENT_A,
> +};
> +
> static struct regmap_irq da9062_irqs[] = {
> /* EVENT A */
> [DA9062_IRQ_ONKEY] = {
> @@ -102,6 +166,57 @@
> .ack_base = DA9062AA_EVENT_A,
> };
>
> +static struct resource da9061_core_resources[] = {
> + DEFINE_RES_IRQ_NAMED(DA9061_IRQ_VDD_WARN, "VDD_WARN"),
> +};
> +
> +static struct resource da9061_regulators_resources[] = {
> + DEFINE_RES_IRQ_NAMED(DA9061_IRQ_LDO_LIM, "LDO_LIM"),
> +};
> +
> +static struct resource da9061_thermal_resources[] = {
> + DEFINE_RES_IRQ_NAMED(DA9061_IRQ_TEMP, "THERMAL"),
> +};
> +
> +static struct resource da9061_wdt_resources[] = {
> + DEFINE_RES_IRQ_NAMED(DA9061_IRQ_WDG_WARN, "WD_WARN"),
> +};
> +
> +static struct resource da9061_onkey_resources[] = {
> + DEFINE_RES_IRQ_NAMED(DA9061_IRQ_ONKEY, "ONKEY"),
> +};
> +
> +static const struct mfd_cell da9061_devs[] = {
> + {
> + .name = "da9061-core",
> + .num_resources = ARRAY_SIZE(da9061_core_resources),
> + .resources = da9061_core_resources,
> + },
> + {
> + .name = "da9062-regulators",
> + .num_resources = ARRAY_SIZE(da9061_regulators_resources),
> + .resources = da9061_regulators_resources,
> + },
> + {
> + .name = "da9061-watchdog",
> + .num_resources = ARRAY_SIZE(da9061_wdt_resources),
> + .resources = da9061_wdt_resources,
> + .of_compatible = "dlg,da9061-watchdog",
> + },
> + {
> + .name = "da9061-thermal",
> + .num_resources = ARRAY_SIZE(da9061_thermal_resources),
> + .resources = da9061_thermal_resources,
> + .of_compatible = "dlg,da9061-thermal",
> + },
> + {
> + .name = "da9061-onkey",
> + .num_resources = ARRAY_SIZE(da9061_onkey_resources),
> + .resources = da9061_onkey_resources,
> + .of_compatible = "dlg,da9061-onkey",
> + },
> +};
> +
> static struct resource da9062_core_resources[] = {
> DEFINE_RES_NAMED(DA9062_IRQ_VDD_WARN, 1, "VDD_WARN", IORESOURCE_IRQ),
> };
> @@ -200,7 +315,8 @@ static int da9062_clear_fault_log(struct da9062 *chip)
>
> static int da9062_get_device_type(struct da9062 *chip)
> {
> - int device_id, variant_id, variant_mrc;
> + int device_id, variant_id, variant_mrc, variant_vrc;
> + char *type;
> int ret;
>
> ret = regmap_read(chip->regmap, DA9062AA_DEVICE_ID, &device_id);
> @@ -219,9 +335,23 @@ static int da9062_get_device_type(struct da9062 *chip)
> return -EIO;
> }
>
> + variant_vrc = (variant_id & DA9062AA_VRC_MASK) >> DA9062AA_VRC_SHIFT;
> +
> + switch (variant_vrc) {
> + case DA9062_PMIC_VARIANT_VRC_DA9061:
> + type = "DA9061";
> + break;
> + case DA9062_PMIC_VARIANT_VRC_DA9062:
> + type = "DA9062";
> + break;
> + default:
> + type = "Unknown";
> + break;
> + }
> +
> dev_info(chip->dev,
> - "Device detected (device-ID: 0x%02X, var-ID: 0x%02X)\n",
> - device_id, variant_id);
> + "Device detected (device-ID: 0x%02X, var-ID: 0x%02X, %s)\n",
> + device_id, variant_id, type);
>
> variant_mrc = (variant_id & DA9062AA_MRC_MASK) >> DA9062AA_MRC_SHIFT;
>
> @@ -234,6 +364,234 @@ static int da9062_get_device_type(struct da9062 *chip)
> return ret;
> }
>
> +static const struct regmap_range da9061_aa_readable_ranges[] = {
> + {
> + .range_min = DA9062AA_PAGE_CON,
> + .range_max = DA9062AA_STATUS_B,
> + }, {
> + .range_min = DA9062AA_STATUS_D,
> + .range_max = DA9062AA_EVENT_C,
> + }, {
> + .range_min = DA9062AA_IRQ_MASK_A,
> + .range_max = DA9062AA_IRQ_MASK_C,
> + }, {
> + .range_min = DA9062AA_CONTROL_A,
> + .range_max = DA9062AA_GPIO_4,
> + }, {
> + .range_min = DA9062AA_GPIO_WKUP_MODE,
> + .range_max = DA9062AA_GPIO_OUT3_4,
> + }, {
> + .range_min = DA9062AA_BUCK1_CONT,
> + .range_max = DA9062AA_BUCK4_CONT,
> + }, {
> + .range_min = DA9062AA_BUCK3_CONT,
> + .range_max = DA9062AA_BUCK3_CONT,
> + }, {
> + .range_min = DA9062AA_LDO1_CONT,
> + .range_max = DA9062AA_LDO4_CONT,
> + }, {
> + .range_min = DA9062AA_DVC_1,
> + .range_max = DA9062AA_DVC_1,
> + }, {
> + .range_min = DA9062AA_SEQ,
> + .range_max = DA9062AA_ID_4_3,
> + }, {
> + .range_min = DA9062AA_ID_12_11,
> + .range_max = DA9062AA_ID_16_15,
> + }, {
> + .range_min = DA9062AA_ID_22_21,
> + .range_max = DA9062AA_ID_32_31,
> + }, {
> + .range_min = DA9062AA_SEQ_A,
> + .range_max = DA9062AA_WAIT,
> + }, {
> + .range_min = DA9062AA_RESET,
> + .range_max = DA9062AA_BUCK_ILIM_C,
> + }, {
> + .range_min = DA9062AA_BUCK1_CFG,
> + .range_max = DA9062AA_BUCK3_CFG,
> + }, {
> + .range_min = DA9062AA_VBUCK1_A,
> + .range_max = DA9062AA_VBUCK4_A,
> + }, {
> + .range_min = DA9062AA_VBUCK3_A,
> + .range_max = DA9062AA_VBUCK3_A,
> + }, {
> + .range_min = DA9062AA_VLDO1_A,
> + .range_max = DA9062AA_VLDO4_A,
> + }, {
> + .range_min = DA9062AA_VBUCK1_B,
> + .range_max = DA9062AA_VBUCK4_B,
> + }, {
> + .range_min = DA9062AA_VBUCK3_B,
> + .range_max = DA9062AA_VBUCK3_B,
> + }, {
> + .range_min = DA9062AA_VLDO1_B,
> + .range_max = DA9062AA_VLDO4_B,
> + }, {
> + .range_min = DA9062AA_BBAT_CONT,
> + .range_max = DA9062AA_BBAT_CONT,
> + }, {
> + .range_min = DA9062AA_INTERFACE,
> + .range_max = DA9062AA_CONFIG_E,
> + }, {
> + .range_min = DA9062AA_CONFIG_G,
> + .range_max = DA9062AA_CONFIG_K,
> + }, {
> + .range_min = DA9062AA_CONFIG_M,
> + .range_max = DA9062AA_CONFIG_M,
> + }, {
> + .range_min = DA9062AA_GP_ID_0,
> + .range_max = DA9062AA_GP_ID_19,
> + }, {
> + .range_min = DA9062AA_DEVICE_ID,
> + .range_max = DA9062AA_CONFIG_ID,
> + },
> +};
> +
> +static const struct regmap_range da9061_aa_writeable_ranges[] = {
> + {
> + .range_min = DA9062AA_PAGE_CON,
> + .range_max = DA9062AA_PAGE_CON,
> + }, {
> + .range_min = DA9062AA_FAULT_LOG,
> + .range_max = DA9062AA_EVENT_C,
> + }, {
> + .range_min = DA9062AA_IRQ_MASK_A,
> + .range_max = DA9062AA_IRQ_MASK_C,
> + }, {
> + .range_min = DA9062AA_CONTROL_A,
> + .range_max = DA9062AA_GPIO_4,
> + }, {
> + .range_min = DA9062AA_GPIO_WKUP_MODE,
> + .range_max = DA9062AA_GPIO_OUT3_4,
> + }, {
> + .range_min = DA9062AA_BUCK1_CONT,
> + .range_max = DA9062AA_BUCK4_CONT,
> + }, {
> + .range_min = DA9062AA_BUCK3_CONT,
> + .range_max = DA9062AA_BUCK3_CONT,
> + }, {
> + .range_min = DA9062AA_LDO1_CONT,
> + .range_max = DA9062AA_LDO4_CONT,
> + }, {
> + .range_min = DA9062AA_DVC_1,
> + .range_max = DA9062AA_DVC_1,
> + }, {
> + .range_min = DA9062AA_SEQ,
> + .range_max = DA9062AA_ID_4_3,
> + }, {
> + .range_min = DA9062AA_ID_12_11,
> + .range_max = DA9062AA_ID_16_15,
> + }, {
> + .range_min = DA9062AA_ID_22_21,
> + .range_max = DA9062AA_ID_32_31,
> + }, {
> + .range_min = DA9062AA_SEQ_A,
> + .range_max = DA9062AA_WAIT,
> + }, {
> + .range_min = DA9062AA_RESET,
> + .range_max = DA9062AA_BUCK_ILIM_C,
> + }, {
> + .range_min = DA9062AA_BUCK1_CFG,
> + .range_max = DA9062AA_BUCK3_CFG,
> + }, {
> + .range_min = DA9062AA_VBUCK1_A,
> + .range_max = DA9062AA_VBUCK4_A,
> + }, {
> + .range_min = DA9062AA_VBUCK3_A,
> + .range_max = DA9062AA_VBUCK3_A,
> + }, {
> + .range_min = DA9062AA_VLDO1_A,
> + .range_max = DA9062AA_VLDO4_A,
> + }, {
> + .range_min = DA9062AA_VBUCK1_B,
> + .range_max = DA9062AA_VBUCK4_B,
> + }, {
> + .range_min = DA9062AA_VBUCK3_B,
> + .range_max = DA9062AA_VBUCK3_B,
> + }, {
> + .range_min = DA9062AA_VLDO1_B,
> + .range_max = DA9062AA_VLDO4_B,
> + }, {
> + .range_min = DA9062AA_BBAT_CONT,
> + .range_max = DA9062AA_BBAT_CONT,
> + }, {
> + .range_min = DA9062AA_GP_ID_0,
> + .range_max = DA9062AA_GP_ID_19,
> + },
> +};
> +
> +static const struct regmap_range da9061_aa_volatile_ranges[] = {
> + {
> + .range_min = DA9062AA_PAGE_CON,
> + .range_max = DA9062AA_STATUS_B,
> + }, {
> + .range_min = DA9062AA_STATUS_D,
> + .range_max = DA9062AA_EVENT_C,
> + }, {
> + .range_min = DA9062AA_CONTROL_A,
> + .range_max = DA9062AA_CONTROL_B,
> + }, {
> + .range_min = DA9062AA_CONTROL_E,
> + .range_max = DA9062AA_CONTROL_F,
> + }, {
> + .range_min = DA9062AA_BUCK1_CONT,
> + .range_max = DA9062AA_BUCK4_CONT,
> + }, {
> + .range_min = DA9062AA_BUCK3_CONT,
> + .range_max = DA9062AA_BUCK3_CONT,
> + }, {
> + .range_min = DA9062AA_LDO1_CONT,
> + .range_max = DA9062AA_LDO4_CONT,
> + }, {
> + .range_min = DA9062AA_DVC_1,
> + .range_max = DA9062AA_DVC_1,
> + }, {
> + .range_min = DA9062AA_SEQ,
> + .range_max = DA9062AA_SEQ,
> + },
> +};
> +
> +static const struct regmap_access_table da9061_aa_readable_table = {
> + .yes_ranges = da9061_aa_readable_ranges,
> + .n_yes_ranges = ARRAY_SIZE(da9061_aa_readable_ranges),
> +};
> +
> +static const struct regmap_access_table da9061_aa_writeable_table = {
> + .yes_ranges = da9061_aa_writeable_ranges,
> + .n_yes_ranges = ARRAY_SIZE(da9061_aa_writeable_ranges),
> +};
> +
> +static const struct regmap_access_table da9061_aa_volatile_table = {
> + .yes_ranges = da9061_aa_volatile_ranges,
> + .n_yes_ranges = ARRAY_SIZE(da9061_aa_volatile_ranges),
> +};
> +
> +static const struct regmap_range_cfg da9061_range_cfg[] = {
> + {
> + .range_min = DA9062AA_PAGE_CON,
> + .range_max = DA9062AA_CONFIG_ID,
> + .selector_reg = DA9062AA_PAGE_CON,
> + .selector_mask = 1 << DA9062_I2C_PAGE_SEL_SHIFT,
> + .selector_shift = DA9062_I2C_PAGE_SEL_SHIFT,
> + .window_start = 0,
> + .window_len = 256,
> + }
> +};
> +
> +static struct regmap_config da9061_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + .ranges = da9061_range_cfg,
> + .num_ranges = ARRAY_SIZE(da9061_range_cfg),
> + .max_register = DA9062AA_CONFIG_ID,
> + .cache_type = REGCACHE_RBTREE,
> + .rd_table = &da9061_aa_readable_table,
> + .wr_table = &da9061_aa_writeable_table,
> + .volatile_table = &da9061_aa_volatile_table,
> +};
> +
> static const struct regmap_range da9062_aa_readable_ranges[] = {
> {
> .range_min = DA9062AA_PAGE_CON,
> @@ -456,17 +814,39 @@ static int da9062_get_device_type(struct da9062 *chip)
> .volatile_table = &da9062_aa_volatile_table,
> };
>
> +static const struct of_device_id da9062_dt_ids[] = {
> + { .compatible = "dlg,da9061", .data = (void *)COMPAT_TYPE_DA9061, },
> + { .compatible = "dlg,da9062", .data = (void *)COMPAT_TYPE_DA9062, },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, da9062_dt_ids);
> +
> static int da9062_i2c_probe(struct i2c_client *i2c,
> const struct i2c_device_id *id)
> {
> struct da9062 *chip;
> + const struct of_device_id *match;
> unsigned int irq_base;
> + const struct mfd_cell *cell;
> + const struct regmap_irq_chip *irq_chip;
> + const struct regmap_config *config;
> + int cell_num;
> int ret;
>
> chip = devm_kzalloc(&i2c->dev, sizeof(*chip), GFP_KERNEL);
> if (!chip)
> return -ENOMEM;
>
> + if (i2c->dev.of_node) {
> + match = of_match_node(da9062_dt_ids, i2c->dev.of_node);
> + if (!match)
> + return -EINVAL;
> +
> + chip->chip_type = (uintptr_t)match->data;
> + } else {
> + chip->chip_type = id->driver_data;
> + }
> +
> i2c_set_clientdata(i2c, chip);
> chip->dev = &i2c->dev;
>
> @@ -475,7 +855,25 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
> return -EINVAL;
> }
>
> - chip->regmap = devm_regmap_init_i2c(i2c, &da9062_regmap_config);
> + switch (chip->chip_type) {
> + case COMPAT_TYPE_DA9061:
> + cell = da9061_devs;
> + cell_num = ARRAY_SIZE(da9061_devs);
> + irq_chip = &da9061_irq_chip;
> + config = &da9061_regmap_config;
> + break;
> + case COMPAT_TYPE_DA9062:
> + cell = da9062_devs;
> + cell_num = ARRAY_SIZE(da9062_devs);
> + irq_chip = &da9062_irq_chip;
> + config = &da9062_regmap_config;
> + break;
> + default:
> + dev_err(chip->dev, "Unrecognised chip type\n");
> + return -ENODEV;
> + }
> +
> + chip->regmap = devm_regmap_init_i2c(i2c, config);
> if (IS_ERR(chip->regmap)) {
> ret = PTR_ERR(chip->regmap);
> dev_err(chip->dev, "Failed to allocate register map: %d\n",
> @@ -493,7 +891,7 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
>
> ret = regmap_add_irq_chip(chip->regmap, i2c->irq,
> IRQF_TRIGGER_LOW | IRQF_ONESHOT | IRQF_SHARED,
> - -1, &da9062_irq_chip,
> + -1, irq_chip,
> &chip->regmap_irq);
> if (ret) {
> dev_err(chip->dev, "Failed to request IRQ %d: %d\n",
> @@ -503,8 +901,8 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
>
> irq_base = regmap_irq_chip_get_base(chip->regmap_irq);
>
> - ret = mfd_add_devices(chip->dev, PLATFORM_DEVID_NONE, da9062_devs,
> - ARRAY_SIZE(da9062_devs), NULL, irq_base,
> + ret = mfd_add_devices(chip->dev, PLATFORM_DEVID_NONE, cell,
> + cell_num, NULL, irq_base,
> NULL);
> if (ret) {
> dev_err(chip->dev, "Cannot register child devices\n");
> @@ -526,17 +924,12 @@ static int da9062_i2c_remove(struct i2c_client *i2c)
> }
>
> static const struct i2c_device_id da9062_i2c_id[] = {
> - { "da9062", 0 },
> + { "da9061", COMPAT_TYPE_DA9061 },
> + { "da9062", COMPAT_TYPE_DA9062 },
> { },
> };
> MODULE_DEVICE_TABLE(i2c, da9062_i2c_id);
>
> -static const struct of_device_id da9062_dt_ids[] = {
> - { .compatible = "dlg,da9062", },
> - { }
> -};
> -MODULE_DEVICE_TABLE(of, da9062_dt_ids);
> -
> static struct i2c_driver da9062_i2c_driver = {
> .driver = {
> .name = "da9062",
> @@ -549,6 +942,6 @@ static int da9062_i2c_remove(struct i2c_client *i2c)
>
> module_i2c_driver(da9062_i2c_driver);
>
> -MODULE_DESCRIPTION("Core device driver for Dialog DA9062");
> +MODULE_DESCRIPTION("Core device driver for Dialog DA9061 and DA9062");
> MODULE_AUTHOR("Steve Twiss <stwiss.opensource@diasemi.com>");
> MODULE_LICENSE("GPL");
> diff --git a/include/linux/mfd/da9062/core.h b/include/linux/mfd/da9062/core.h
> index 376ba84..74d33a0 100644
> --- a/include/linux/mfd/da9062/core.h
> +++ b/include/linux/mfd/da9062/core.h
> @@ -1,5 +1,5 @@
> /*
> - * Copyright (C) 2015 Dialog Semiconductor Ltd.
> + * Copyright (C) 2015-2017 Dialog Semiconductor
> *
> * This program is free software; you can redistribute it and/or
> * modify it under the terms of the GNU General Public License
> @@ -18,7 +18,31 @@
> #include <linux/interrupt.h>
> #include <linux/mfd/da9062/registers.h>
>
> -/* Interrupts */
> +enum da9062_compatible_types {
> + COMPAT_TYPE_DA9061 = 1,
> + COMPAT_TYPE_DA9062,
> +};
> +
> +enum da9061_irqs {
> + /* IRQ A */
> + DA9061_IRQ_ONKEY,
> + DA9061_IRQ_WDG_WARN,
> + DA9061_IRQ_SEQ_RDY,
> + /* IRQ B*/
> + DA9061_IRQ_TEMP,
> + DA9061_IRQ_LDO_LIM,
> + DA9061_IRQ_DVC_RDY,
> + DA9061_IRQ_VDD_WARN,
> + /* IRQ C */
> + DA9061_IRQ_GPI0,
> + DA9061_IRQ_GPI1,
> + DA9061_IRQ_GPI2,
> + DA9061_IRQ_GPI3,
> + DA9061_IRQ_GPI4,
> +
> + DA9061_NUM_IRQ,
> +};
> +
> enum da9062_irqs {
> /* IRQ A */
> DA9062_IRQ_ONKEY,
> @@ -45,6 +69,7 @@ struct da9062 {
> struct device *dev;
> struct regmap *regmap;
> struct regmap_irq_chip_data *regmap_irq;
> + enum da9062_compatible_types chip_type;
> };
>
> #endif /* __MFD_DA9062_CORE_H__ */
> diff --git a/include/linux/mfd/da9062/registers.h b/include/linux/mfd/da9062/registers.h
> index 97790d1..18d576a 100644
> --- a/include/linux/mfd/da9062/registers.h
> +++ b/include/linux/mfd/da9062/registers.h
> @@ -1,6 +1,5 @@
> /*
> - * registers.h - REGISTERS H for DA9062
> - * Copyright (C) 2015 Dialog Semiconductor Ltd.
> + * Copyright (C) 2015-2017 Dialog Semiconductor
> *
> * This program is free software; you can redistribute it and/or
> * modify it under the terms of the GNU General Public License
> @@ -18,6 +17,8 @@
>
> #define DA9062_PMIC_DEVICE_ID 0x62
> #define DA9062_PMIC_VARIANT_MRC_AA 0x01
> +#define DA9062_PMIC_VARIANT_VRC_DA9061 0x01
> +#define DA9062_PMIC_VARIANT_VRC_DA9062 0x02
>
> #define DA9062_I2C_PAGE_SEL_SHIFT 1
>
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 36+ messages in thread* RE: [PATCH V7 4/7] mfd: da9061: MFD core support
2017-04-04 8:39 ` Lee Jones
@ 2017-04-24 10:37 ` Steve Twiss
-1 siblings, 0 replies; 36+ messages in thread
From: Steve Twiss @ 2017-04-24 10:37 UTC (permalink / raw)
To: Lee Jones
Cc: LINUX-KERNEL, DEVICETREE, Dmitry Torokhov, Eduardo Valentin,
Guenter Roeck, LINUX-INPUT, LINUX-PM, LINUX-WATCHDOG,
Liam Girdwood, Mark Brown, Mark Rutland, Rob Herring,
Support Opensource, Wim Van Sebroeck, Zhang Rui
On 04 April 2017 09:39, Lee Jones wrote:
> Subject: Re: [PATCH V7 4/7] mfd: da9061: MFD core support
>
> On Mon, 03 Apr 2017, Steve Twiss wrote:
> > From: Steve Twiss <stwiss.opensource@diasemi.com>
> > MFD support for DA9061 is provided as part of the DA9062 device driver.
> >
> > The registers header file adds two new chip variant IDs defined in DA9061
> > and DA9062 hardware. The core header file adds new software enumerations
> > for listing the valid DA9061 IRQs and a da9062_compatible_types enumeration
> > for distinguishing between DA9061/62 devices in software.
> >
> > The core source code adds a new .compatible of_device_id entry. This is
> > extended from DA9062 to support both "dlg,da9061" and "dlg,da9062". The
> > .data entry now holds a reference to the enumerated device type.
> >
> > A new regmap_irq_chip model is added for DA9061 and this supports the new
> > list of regmap_irq entries. A new mfd_cell da9061_devs[] array lists the
> > new sub system components for DA9061. Support is added for a new DA9061
> > regmap_config which lists the correct readable, writable and volatile
> > ranges for this chip.
> >
> > The probe function uses the device tree compatible string to switch on the
> > da9062_compatible_types and configure the correct mfd cells, irq chip and
> > regmap config.
> >
> > Kconfig is updated to reflect support for DA9061 and DA9062 PMICs.
> >
> > Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
>
> Ah, here it is.
>
> Applied, thanks.
Hi Lee,
I noticed the DA9061 core support has been added into linux-next, however
the commit message was changed from the original title:
"mfd: da9061: MFD core support"
to add the mistake:
"mfd: Add suppfor for DA9061"
https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?id=d3fe0806025cacdab1462d5704e1c98ab9db4564
Can this be fixed please?
This patch has not been upstreamed into linux-mainline and is still in linux-next.
Regards,
Steve
^ permalink raw reply [flat|nested] 36+ messages in thread
* RE: [PATCH V7 4/7] mfd: da9061: MFD core support
@ 2017-04-24 10:37 ` Steve Twiss
0 siblings, 0 replies; 36+ messages in thread
From: Steve Twiss @ 2017-04-24 10:37 UTC (permalink / raw)
To: Lee Jones
Cc: LINUX-KERNEL, DEVICETREE, Dmitry Torokhov, Eduardo Valentin,
Guenter Roeck, LINUX-INPUT, LINUX-PM, LINUX-WATCHDOG,
Liam Girdwood, Mark Brown, Mark Rutland, Rob Herring,
Support Opensource, Wim Van Sebroeck, Zhang Rui
On 04 April 2017 09:39, Lee Jones wrote:
> Subject: Re: [PATCH V7 4/7] mfd: da9061: MFD core support
>
> On Mon, 03 Apr 2017, Steve Twiss wrote:
> > From: Steve Twiss <stwiss.opensource@diasemi.com>
> > MFD support for DA9061 is provided as part of the DA9062 device driver.
> >
> > The registers header file adds two new chip variant IDs defined in DA9061
> > and DA9062 hardware. The core header file adds new software enumerations
> > for listing the valid DA9061 IRQs and a da9062_compatible_types enumeration
> > for distinguishing between DA9061/62 devices in software.
> >
> > The core source code adds a new .compatible of_device_id entry. This is
> > extended from DA9062 to support both "dlg,da9061" and "dlg,da9062". The
> > .data entry now holds a reference to the enumerated device type.
> >
> > A new regmap_irq_chip model is added for DA9061 and this supports the new
> > list of regmap_irq entries. A new mfd_cell da9061_devs[] array lists the
> > new sub system components for DA9061. Support is added for a new DA9061
> > regmap_config which lists the correct readable, writable and volatile
> > ranges for this chip.
> >
> > The probe function uses the device tree compatible string to switch on the
> > da9062_compatible_types and configure the correct mfd cells, irq chip and
> > regmap config.
> >
> > Kconfig is updated to reflect support for DA9061 and DA9062 PMICs.
> >
> > Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
>
> Ah, here it is.
>
> Applied, thanks.
Hi Lee,
I noticed the DA9061 core support has been added into linux-next, however
the commit message was changed from the original title:
"mfd: da9061: MFD core support"
to add the mistake:
"mfd: Add suppfor for DA9061"
https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?id=d3fe0806025cacdab1462d5704e1c98ab9db4564
Can this be fixed please?
This patch has not been upstreamed into linux-mainline and is still in linux-next.
Regards,
Steve
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH V7 4/7] mfd: da9061: MFD core support
2017-04-24 10:37 ` Steve Twiss
@ 2017-04-24 12:38 ` Lee Jones
-1 siblings, 0 replies; 36+ messages in thread
From: Lee Jones @ 2017-04-24 12:38 UTC (permalink / raw)
To: Steve Twiss
Cc: LINUX-KERNEL, DEVICETREE, Dmitry Torokhov, Eduardo Valentin,
Guenter Roeck, LINUX-INPUT, LINUX-PM, LINUX-WATCHDOG,
Liam Girdwood, Mark Brown, Mark Rutland, Rob Herring,
Support Opensource, Wim Van Sebroeck, Zhang Rui
On Mon, 24 Apr 2017, Steve Twiss wrote:
> On 04 April 2017 09:39, Lee Jones wrote:
> > Subject: Re: [PATCH V7 4/7] mfd: da9061: MFD core support
> >
> > On Mon, 03 Apr 2017, Steve Twiss wrote:
> > > From: Steve Twiss <stwiss.opensource@diasemi.com>
> > > MFD support for DA9061 is provided as part of the DA9062 device driver.
> > >
> > > The registers header file adds two new chip variant IDs defined in DA9061
> > > and DA9062 hardware. The core header file adds new software enumerations
> > > for listing the valid DA9061 IRQs and a da9062_compatible_types enumeration
> > > for distinguishing between DA9061/62 devices in software.
> > >
> > > The core source code adds a new .compatible of_device_id entry. This is
> > > extended from DA9062 to support both "dlg,da9061" and "dlg,da9062". The
> > > .data entry now holds a reference to the enumerated device type.
> > >
> > > A new regmap_irq_chip model is added for DA9061 and this supports the new
> > > list of regmap_irq entries. A new mfd_cell da9061_devs[] array lists the
> > > new sub system components for DA9061. Support is added for a new DA9061
> > > regmap_config which lists the correct readable, writable and volatile
> > > ranges for this chip.
> > >
> > > The probe function uses the device tree compatible string to switch on the
> > > da9062_compatible_types and configure the correct mfd cells, irq chip and
> > > regmap config.
> > >
> > > Kconfig is updated to reflect support for DA9061 and DA9062 PMICs.
> > >
> > > Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
> >
> > Ah, here it is.
> >
> > Applied, thanks.
>
> Hi Lee,
>
> I noticed the DA9061 core support has been added into linux-next, however
> the commit message was changed from the original title:
>
> "mfd: da9061: MFD core support"
>
> to add the mistake:
>
> "mfd: Add suppfor for DA9061"
>
> https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?id=d3fe0806025cacdab1462d5704e1c98ab9db4564
>
> Can this be fixed please?
> This patch has not been upstreamed into linux-mainline and is still in linux-next.
You're right, thanks for pointing that out.
Now fixed.
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH V7 4/7] mfd: da9061: MFD core support
@ 2017-04-24 12:38 ` Lee Jones
0 siblings, 0 replies; 36+ messages in thread
From: Lee Jones @ 2017-04-24 12:38 UTC (permalink / raw)
To: Steve Twiss
Cc: LINUX-KERNEL, DEVICETREE, Dmitry Torokhov, Eduardo Valentin,
Guenter Roeck, LINUX-INPUT, LINUX-PM, LINUX-WATCHDOG,
Liam Girdwood, Mark Brown, Mark Rutland, Rob Herring,
Support Opensource, Wim Van Sebroeck, Zhang Rui
On Mon, 24 Apr 2017, Steve Twiss wrote:
> On 04 April 2017 09:39, Lee Jones wrote:
> > Subject: Re: [PATCH V7 4/7] mfd: da9061: MFD core support
> >
> > On Mon, 03 Apr 2017, Steve Twiss wrote:
> > > From: Steve Twiss <stwiss.opensource@diasemi.com>
> > > MFD support for DA9061 is provided as part of the DA9062 device driver.
> > >
> > > The registers header file adds two new chip variant IDs defined in DA9061
> > > and DA9062 hardware. The core header file adds new software enumerations
> > > for listing the valid DA9061 IRQs and a da9062_compatible_types enumeration
> > > for distinguishing between DA9061/62 devices in software.
> > >
> > > The core source code adds a new .compatible of_device_id entry. This is
> > > extended from DA9062 to support both "dlg,da9061" and "dlg,da9062". The
> > > .data entry now holds a reference to the enumerated device type.
> > >
> > > A new regmap_irq_chip model is added for DA9061 and this supports the new
> > > list of regmap_irq entries. A new mfd_cell da9061_devs[] array lists the
> > > new sub system components for DA9061. Support is added for a new DA9061
> > > regmap_config which lists the correct readable, writable and volatile
> > > ranges for this chip.
> > >
> > > The probe function uses the device tree compatible string to switch on the
> > > da9062_compatible_types and configure the correct mfd cells, irq chip and
> > > regmap config.
> > >
> > > Kconfig is updated to reflect support for DA9061 and DA9062 PMICs.
> > >
> > > Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
> >
> > Ah, here it is.
> >
> > Applied, thanks.
>
> Hi Lee,
>
> I noticed the DA9061 core support has been added into linux-next, however
> the commit message was changed from the original title:
>
> "mfd: da9061: MFD core support"
>
> to add the mistake:
>
> "mfd: Add suppfor for DA9061"
>
> https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?id=d3fe0806025cacdab1462d5704e1c98ab9db4564
>
> Can this be fixed please?
> This patch has not been upstreamed into linux-mainline and is still in linux-next.
You're right, thanks for pointing that out.
Now fixed.
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 36+ messages in thread