* [PATCH v5 0/2] Add cpufreq support for Armada 8K @ 2019-01-18 14:11 ` Gregory CLEMENT 0 siblings, 0 replies; 10+ messages in thread From: Gregory CLEMENT @ 2019-01-18 14:11 UTC (permalink / raw) To: Rafael J. Wysocki, Viresh Kumar, linux-pm Cc: Andrew Lunn, Jason Cooper, Antoine Tenart, Gregory CLEMENT, Maxime Chevallier, Thomas Petazzoni, Miquèl Raynal, linux-arm-kernel, Sebastian Hesselbarth Hi, this is the fifth version of a the series adding the cpufreq support for the Marvell Armada 8K SoCs. Gregory Changelog: v4 -> v5: - Rebased onto v5.0-rc1 - Rewrite the clk_get part in armada_8k_get_sharing_cpus() - Reverse the call function order in armada_8k_cpufreq_exit() v3 -> v4: - Remove most of the global variable and use the private data of the platfrom device to store the freq_tables struct. - Remove the clk pointer of the freq_table struct which is no more needed with the new way to register the opp - Check the get_cpu_device() return. - Balance the clk_get() calls. - No more use the devm_ function. - Base the registration of the opp on the cpu mask updated after each iteration to find the shared cpus. - Base the free on the NULL or 0 value of the freq_table struct members, it allows to remove the global index. v2 -> v3 - Make the driver really modular (modprobe;modprobe -r;modprobe; is working) - Don't use anymore 100MHz as minimal frequency, but only max frequency/4 - Fix remaining warning reported by checkpatch - Rework the registering of the opp v1 -> v2: - Fix typos in MAINTAINERS (reported by Baruch Siach) and in armada-8k-cpufreq.c (reported by Thomas Petazzoni) - Fix indentation in Kconfig.arm (reported by Thomas Petazzoni) - Use const for opps_div (reported by Thomas Petazzoni) - Fix memory leak of opps_array (reported by Thomas Petazzoni) Gregory CLEMENT (2): MAINTAINERS: add new entries for Armada 8K cpufreq driver cpufreq: ap806: add cpufreq driver for Armada 8K MAINTAINERS | 1 + drivers/cpufreq/Kconfig.arm | 11 ++ drivers/cpufreq/Makefile | 1 + drivers/cpufreq/armada-8k-cpufreq.c | 203 ++++++++++++++++++++++++++++ 4 files changed, 216 insertions(+) create mode 100644 drivers/cpufreq/armada-8k-cpufreq.c -- 2.20.1 ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v5 0/2] Add cpufreq support for Armada 8K @ 2019-01-18 14:11 ` Gregory CLEMENT 0 siblings, 0 replies; 10+ messages in thread From: Gregory CLEMENT @ 2019-01-18 14:11 UTC (permalink / raw) To: Rafael J. Wysocki, Viresh Kumar, linux-pm Cc: Andrew Lunn, Jason Cooper, Antoine Tenart, Gregory CLEMENT, Maxime Chevallier, Thomas Petazzoni, Miquèl Raynal, linux-arm-kernel, Sebastian Hesselbarth Hi, this is the fifth version of a the series adding the cpufreq support for the Marvell Armada 8K SoCs. Gregory Changelog: v4 -> v5: - Rebased onto v5.0-rc1 - Rewrite the clk_get part in armada_8k_get_sharing_cpus() - Reverse the call function order in armada_8k_cpufreq_exit() v3 -> v4: - Remove most of the global variable and use the private data of the platfrom device to store the freq_tables struct. - Remove the clk pointer of the freq_table struct which is no more needed with the new way to register the opp - Check the get_cpu_device() return. - Balance the clk_get() calls. - No more use the devm_ function. - Base the registration of the opp on the cpu mask updated after each iteration to find the shared cpus. - Base the free on the NULL or 0 value of the freq_table struct members, it allows to remove the global index. v2 -> v3 - Make the driver really modular (modprobe;modprobe -r;modprobe; is working) - Don't use anymore 100MHz as minimal frequency, but only max frequency/4 - Fix remaining warning reported by checkpatch - Rework the registering of the opp v1 -> v2: - Fix typos in MAINTAINERS (reported by Baruch Siach) and in armada-8k-cpufreq.c (reported by Thomas Petazzoni) - Fix indentation in Kconfig.arm (reported by Thomas Petazzoni) - Use const for opps_div (reported by Thomas Petazzoni) - Fix memory leak of opps_array (reported by Thomas Petazzoni) Gregory CLEMENT (2): MAINTAINERS: add new entries for Armada 8K cpufreq driver cpufreq: ap806: add cpufreq driver for Armada 8K MAINTAINERS | 1 + drivers/cpufreq/Kconfig.arm | 11 ++ drivers/cpufreq/Makefile | 1 + drivers/cpufreq/armada-8k-cpufreq.c | 203 ++++++++++++++++++++++++++++ 4 files changed, 216 insertions(+) create mode 100644 drivers/cpufreq/armada-8k-cpufreq.c -- 2.20.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v5 1/2] MAINTAINERS: add new entries for Armada 8K cpufreq driver 2019-01-18 14:11 ` Gregory CLEMENT @ 2019-01-18 14:11 ` Gregory CLEMENT -1 siblings, 0 replies; 10+ messages in thread From: Gregory CLEMENT @ 2019-01-18 14:11 UTC (permalink / raw) To: Rafael J. Wysocki, Viresh Kumar, linux-pm Cc: Andrew Lunn, Jason Cooper, Antoine Tenart, Gregory CLEMENT, Maxime Chevallier, Thomas Petazzoni, Miquèl Raynal, linux-arm-kernel, Sebastian Hesselbarth This new driver belongs to the mvebu family, update the MAINTAINER file to document it. Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> --- MAINTAINERS | 1 + 1 file changed, 1 insertion(+) diff --git a/MAINTAINERS b/MAINTAINERS index 32d444476a90..4a3d62a83e35 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1737,6 +1737,7 @@ F: arch/arm/configs/mvebu_*_defconfig F: arch/arm/mach-mvebu/ F: arch/arm64/boot/dts/marvell/armada* F: drivers/cpufreq/armada-37xx-cpufreq.c +F: drivers/cpufreq/armada-8k-cpufreq.c F: drivers/cpufreq/mvebu-cpufreq.c F: drivers/irqchip/irq-armada-370-xp.c F: drivers/irqchip/irq-mvebu-* -- 2.20.1 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v5 1/2] MAINTAINERS: add new entries for Armada 8K cpufreq driver @ 2019-01-18 14:11 ` Gregory CLEMENT 0 siblings, 0 replies; 10+ messages in thread From: Gregory CLEMENT @ 2019-01-18 14:11 UTC (permalink / raw) To: Rafael J. Wysocki, Viresh Kumar, linux-pm Cc: Andrew Lunn, Jason Cooper, Antoine Tenart, Gregory CLEMENT, Maxime Chevallier, Thomas Petazzoni, Miquèl Raynal, linux-arm-kernel, Sebastian Hesselbarth This new driver belongs to the mvebu family, update the MAINTAINER file to document it. Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> --- MAINTAINERS | 1 + 1 file changed, 1 insertion(+) diff --git a/MAINTAINERS b/MAINTAINERS index 32d444476a90..4a3d62a83e35 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1737,6 +1737,7 @@ F: arch/arm/configs/mvebu_*_defconfig F: arch/arm/mach-mvebu/ F: arch/arm64/boot/dts/marvell/armada* F: drivers/cpufreq/armada-37xx-cpufreq.c +F: drivers/cpufreq/armada-8k-cpufreq.c F: drivers/cpufreq/mvebu-cpufreq.c F: drivers/irqchip/irq-armada-370-xp.c F: drivers/irqchip/irq-mvebu-* -- 2.20.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v5 2/2] cpufreq: ap806: add cpufreq driver for Armada 8K 2019-01-18 14:11 ` Gregory CLEMENT @ 2019-01-18 14:11 ` Gregory CLEMENT -1 siblings, 0 replies; 10+ messages in thread From: Gregory CLEMENT @ 2019-01-18 14:11 UTC (permalink / raw) To: Rafael J. Wysocki, Viresh Kumar, linux-pm Cc: Andrew Lunn, Jason Cooper, Antoine Tenart, Gregory CLEMENT, Maxime Chevallier, Thomas Petazzoni, Miquèl Raynal, linux-arm-kernel, Sebastian Hesselbarth Add cpufreq driver for Marvell AP-806 found on Aramda 8K. The AP-806 has DFS (Dynamic Frequency Scaling) with coupled clock domain for two clusters, so this driver will directly use generic cpufreq-dt driver as backend. Based on the work of Omri Itach <omrii@marvell.com>. Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> --- drivers/cpufreq/Kconfig.arm | 11 ++ drivers/cpufreq/Makefile | 1 + drivers/cpufreq/armada-8k-cpufreq.c | 203 ++++++++++++++++++++++++++++ 3 files changed, 215 insertions(+) create mode 100644 drivers/cpufreq/armada-8k-cpufreq.c diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm index 688f10227793..10bc5c798d17 100644 --- a/drivers/cpufreq/Kconfig.arm +++ b/drivers/cpufreq/Kconfig.arm @@ -25,6 +25,17 @@ config ARM_ARMADA_37XX_CPUFREQ This adds the CPUFreq driver support for Marvell Armada 37xx SoCs. The Armada 37xx PMU supports 4 frequency and VDD levels. +config ARM_ARMADA_8K_CPUFREQ + tristate "Armada 8K CPUFreq driver" + depends on ARCH_MVEBU && CPUFREQ_DT + help + This enables the CPUFreq driver support for Marvell + Armada8k SOCs. + Armada8K device has the AP806 which supports scaling + to any full integer divider. + + If in doubt, say N. + # big LITTLE core layer and glue drivers config ARM_BIG_LITTLE_CPUFREQ tristate "Generic ARM big LITTLE CPUfreq driver" diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile index 08c071be2491..689b26c6f949 100644 --- a/drivers/cpufreq/Makefile +++ b/drivers/cpufreq/Makefile @@ -50,6 +50,7 @@ obj-$(CONFIG_X86_SFI_CPUFREQ) += sfi-cpufreq.o obj-$(CONFIG_ARM_BIG_LITTLE_CPUFREQ) += arm_big_little.o obj-$(CONFIG_ARM_ARMADA_37XX_CPUFREQ) += armada-37xx-cpufreq.o +obj-$(CONFIG_ARM_ARMADA_8K_CPUFREQ) += armada-8k-cpufreq.o obj-$(CONFIG_ARM_BRCMSTB_AVS_CPUFREQ) += brcmstb-avs-cpufreq.o obj-$(CONFIG_ACPI_CPPC_CPUFREQ) += cppc_cpufreq.o obj-$(CONFIG_ARCH_DAVINCI) += davinci-cpufreq.o diff --git a/drivers/cpufreq/armada-8k-cpufreq.c b/drivers/cpufreq/armada-8k-cpufreq.c new file mode 100644 index 000000000000..80375de4e149 --- /dev/null +++ b/drivers/cpufreq/armada-8k-cpufreq.c @@ -0,0 +1,203 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * CPUFreq support for Armada 8K + * + * Copyright (C) 2018 Marvell + * + * Omri Itach <omrii@marvell.com> + * Gregory Clement <gregory.clement@bootlin.com> + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#include <linux/clk.h> +#include <linux/cpu.h> +#include <linux/err.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/pm_opp.h> +#include <linux/slab.h> + +/* + * Setup the opps list with the divider for the max frequency, that + * will be filled at runtime. + */ +static const int opps_div[] __initconst = {1, 2, 3, 4}; + +static struct platform_device *armada_8k_pdev; + +struct freq_table { + struct device *cpu_dev; + unsigned int freq[ARRAY_SIZE(opps_div)]; +}; + +/* If the CPUs share the same clock, then they are in the same cluster. */ +static void __init armada_8k_get_sharing_cpus(struct clk *cur_clk, + struct cpumask *cpumask) +{ + int cpu; + + for_each_possible_cpu(cpu) { + struct device *cpu_dev; + struct clk *clk; + + cpu_dev = get_cpu_device(cpu); + if (!cpu_dev) { + pr_warn("Failed to get cpu%d device\n", cpu); + continue; + } + + clk = clk_get(cpu_dev, 0); + if (IS_ERR(clk)) + pr_warn("Cannot get clock for CPU %d\n", cpu); + else if (clk_is_match(clk, cur_clk)) + cpumask_set_cpu(cpu, cpumask); + + if (!IS_ERR(clk)) + clk_put(clk); + } +} + +static int __init armada_8k_add_opp(struct clk *clk, struct device *cpu_dev, + struct freq_table *freq_tables, + int opps_index) +{ + unsigned int cur_frequency; + unsigned int freq; + int i, ret; + + /* Get nominal (current) CPU frequency. */ + cur_frequency = clk_get_rate(clk); + if (!cur_frequency) { + dev_err(cpu_dev, "Failed to get clock rate for this CPU\n"); + return -EINVAL; + } + + freq_tables[opps_index].cpu_dev = cpu_dev; + + for (i = 0; i < ARRAY_SIZE(opps_div); i++) { + freq = cur_frequency / opps_div[i]; + + ret = dev_pm_opp_add(cpu_dev, freq, 0); + if (ret) + return ret; + + freq_tables[opps_index].freq[i] = freq; + } + + return 0; +} + +static void armada_8k_cpufreq_free_table(struct freq_table *freq_tables) +{ + int opps_index, nb_cpus = num_possible_cpus(); + + for (opps_index = 0 ; opps_index <= nb_cpus; opps_index++) { + int i; + + /* If cpu_dev is NULL then we reached the end of the array */ + if (!freq_tables[opps_index].cpu_dev) + break; + + for (i = 0; i < ARRAY_SIZE(opps_div); i++) { + /* + * A 0Hz frequency is not valid, this meant + * that it was not yet initialized so there is + * no more opp to free + */ + if (freq_tables[opps_index].freq[i] == 0) + break; + + dev_pm_opp_remove(freq_tables[opps_index].cpu_dev, + freq_tables[opps_index].freq[i]); + } + } + + kfree(freq_tables); +} + +static int __init armada_8k_cpufreq_init(void) +{ + int ret = 0, opps_index = 0, cpu, nb_cpus; + struct freq_table *freq_tables; + struct device_node *node; + struct cpumask cpus; + + node = of_find_compatible_node(NULL, NULL, "marvell,ap806-cpu-clock"); + if (!node || !of_device_is_available(node)) + return -ENODEV; + + nb_cpus = num_possible_cpus(); + freq_tables = kcalloc(nb_cpus, sizeof(*freq_tables), GFP_KERNEL); + cpumask_copy(&cpus, cpu_possible_mask); + + /* + * For each CPU, this loop registers the operating points + * supported (which are the nominal CPU frequency and full integer + * divisions of it). + */ + for_each_cpu(cpu, &cpus) { + struct cpumask shared_cpus; + struct device *cpu_dev; + struct clk *clk; + + cpu_dev = get_cpu_device(cpu); + + if (!cpu_dev) { + pr_err("Cannot get CPU %d\n", cpu); + continue; + } + + clk = clk_get(cpu_dev, 0); + + if (IS_ERR(clk)) { + pr_err("Cannot get clock for CPU %d\n", cpu); + ret = PTR_ERR(clk); + goto remove_opp; + } + + ret = armada_8k_add_opp(clk, cpu_dev, freq_tables, opps_index); + if (ret) { + clk_put(clk); + goto remove_opp; + } + + opps_index++; + cpumask_clear(&shared_cpus); + armada_8k_get_sharing_cpus(clk, &shared_cpus); + dev_pm_opp_set_sharing_cpus(cpu_dev, &shared_cpus); + cpumask_andnot(&cpus, &cpus, &shared_cpus); + clk_put(clk); + } + + armada_8k_pdev = platform_device_register_simple("cpufreq-dt", -1, + NULL, 0); + ret = PTR_ERR_OR_ZERO(armada_8k_pdev); + if (ret) + goto remove_opp; + + platform_set_drvdata(armada_8k_pdev, freq_tables); + + return 0; + +remove_opp: + armada_8k_cpufreq_free_table(freq_tables); + return ret; +} +module_init(armada_8k_cpufreq_init); + +static void __exit armada_8k_cpufreq_exit(void) +{ + struct freq_table *freq_tables = platform_get_drvdata(armada_8k_pdev); + + armada_8k_cpufreq_free_table(freq_tables); + platform_device_unregister(armada_8k_pdev); +} +module_exit(armada_8k_cpufreq_exit); + +MODULE_AUTHOR("Gregory Clement <gregory.clement@bootlin.com>"); +MODULE_DESCRIPTION("Armada 8K cpufreq driver"); +MODULE_LICENSE("GPL"); -- 2.20.1 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v5 2/2] cpufreq: ap806: add cpufreq driver for Armada 8K @ 2019-01-18 14:11 ` Gregory CLEMENT 0 siblings, 0 replies; 10+ messages in thread From: Gregory CLEMENT @ 2019-01-18 14:11 UTC (permalink / raw) To: Rafael J. Wysocki, Viresh Kumar, linux-pm Cc: Andrew Lunn, Jason Cooper, Antoine Tenart, Gregory CLEMENT, Maxime Chevallier, Thomas Petazzoni, Miquèl Raynal, linux-arm-kernel, Sebastian Hesselbarth Add cpufreq driver for Marvell AP-806 found on Aramda 8K. The AP-806 has DFS (Dynamic Frequency Scaling) with coupled clock domain for two clusters, so this driver will directly use generic cpufreq-dt driver as backend. Based on the work of Omri Itach <omrii@marvell.com>. Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> --- drivers/cpufreq/Kconfig.arm | 11 ++ drivers/cpufreq/Makefile | 1 + drivers/cpufreq/armada-8k-cpufreq.c | 203 ++++++++++++++++++++++++++++ 3 files changed, 215 insertions(+) create mode 100644 drivers/cpufreq/armada-8k-cpufreq.c diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm index 688f10227793..10bc5c798d17 100644 --- a/drivers/cpufreq/Kconfig.arm +++ b/drivers/cpufreq/Kconfig.arm @@ -25,6 +25,17 @@ config ARM_ARMADA_37XX_CPUFREQ This adds the CPUFreq driver support for Marvell Armada 37xx SoCs. The Armada 37xx PMU supports 4 frequency and VDD levels. +config ARM_ARMADA_8K_CPUFREQ + tristate "Armada 8K CPUFreq driver" + depends on ARCH_MVEBU && CPUFREQ_DT + help + This enables the CPUFreq driver support for Marvell + Armada8k SOCs. + Armada8K device has the AP806 which supports scaling + to any full integer divider. + + If in doubt, say N. + # big LITTLE core layer and glue drivers config ARM_BIG_LITTLE_CPUFREQ tristate "Generic ARM big LITTLE CPUfreq driver" diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile index 08c071be2491..689b26c6f949 100644 --- a/drivers/cpufreq/Makefile +++ b/drivers/cpufreq/Makefile @@ -50,6 +50,7 @@ obj-$(CONFIG_X86_SFI_CPUFREQ) += sfi-cpufreq.o obj-$(CONFIG_ARM_BIG_LITTLE_CPUFREQ) += arm_big_little.o obj-$(CONFIG_ARM_ARMADA_37XX_CPUFREQ) += armada-37xx-cpufreq.o +obj-$(CONFIG_ARM_ARMADA_8K_CPUFREQ) += armada-8k-cpufreq.o obj-$(CONFIG_ARM_BRCMSTB_AVS_CPUFREQ) += brcmstb-avs-cpufreq.o obj-$(CONFIG_ACPI_CPPC_CPUFREQ) += cppc_cpufreq.o obj-$(CONFIG_ARCH_DAVINCI) += davinci-cpufreq.o diff --git a/drivers/cpufreq/armada-8k-cpufreq.c b/drivers/cpufreq/armada-8k-cpufreq.c new file mode 100644 index 000000000000..80375de4e149 --- /dev/null +++ b/drivers/cpufreq/armada-8k-cpufreq.c @@ -0,0 +1,203 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * CPUFreq support for Armada 8K + * + * Copyright (C) 2018 Marvell + * + * Omri Itach <omrii@marvell.com> + * Gregory Clement <gregory.clement@bootlin.com> + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#include <linux/clk.h> +#include <linux/cpu.h> +#include <linux/err.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/pm_opp.h> +#include <linux/slab.h> + +/* + * Setup the opps list with the divider for the max frequency, that + * will be filled at runtime. + */ +static const int opps_div[] __initconst = {1, 2, 3, 4}; + +static struct platform_device *armada_8k_pdev; + +struct freq_table { + struct device *cpu_dev; + unsigned int freq[ARRAY_SIZE(opps_div)]; +}; + +/* If the CPUs share the same clock, then they are in the same cluster. */ +static void __init armada_8k_get_sharing_cpus(struct clk *cur_clk, + struct cpumask *cpumask) +{ + int cpu; + + for_each_possible_cpu(cpu) { + struct device *cpu_dev; + struct clk *clk; + + cpu_dev = get_cpu_device(cpu); + if (!cpu_dev) { + pr_warn("Failed to get cpu%d device\n", cpu); + continue; + } + + clk = clk_get(cpu_dev, 0); + if (IS_ERR(clk)) + pr_warn("Cannot get clock for CPU %d\n", cpu); + else if (clk_is_match(clk, cur_clk)) + cpumask_set_cpu(cpu, cpumask); + + if (!IS_ERR(clk)) + clk_put(clk); + } +} + +static int __init armada_8k_add_opp(struct clk *clk, struct device *cpu_dev, + struct freq_table *freq_tables, + int opps_index) +{ + unsigned int cur_frequency; + unsigned int freq; + int i, ret; + + /* Get nominal (current) CPU frequency. */ + cur_frequency = clk_get_rate(clk); + if (!cur_frequency) { + dev_err(cpu_dev, "Failed to get clock rate for this CPU\n"); + return -EINVAL; + } + + freq_tables[opps_index].cpu_dev = cpu_dev; + + for (i = 0; i < ARRAY_SIZE(opps_div); i++) { + freq = cur_frequency / opps_div[i]; + + ret = dev_pm_opp_add(cpu_dev, freq, 0); + if (ret) + return ret; + + freq_tables[opps_index].freq[i] = freq; + } + + return 0; +} + +static void armada_8k_cpufreq_free_table(struct freq_table *freq_tables) +{ + int opps_index, nb_cpus = num_possible_cpus(); + + for (opps_index = 0 ; opps_index <= nb_cpus; opps_index++) { + int i; + + /* If cpu_dev is NULL then we reached the end of the array */ + if (!freq_tables[opps_index].cpu_dev) + break; + + for (i = 0; i < ARRAY_SIZE(opps_div); i++) { + /* + * A 0Hz frequency is not valid, this meant + * that it was not yet initialized so there is + * no more opp to free + */ + if (freq_tables[opps_index].freq[i] == 0) + break; + + dev_pm_opp_remove(freq_tables[opps_index].cpu_dev, + freq_tables[opps_index].freq[i]); + } + } + + kfree(freq_tables); +} + +static int __init armada_8k_cpufreq_init(void) +{ + int ret = 0, opps_index = 0, cpu, nb_cpus; + struct freq_table *freq_tables; + struct device_node *node; + struct cpumask cpus; + + node = of_find_compatible_node(NULL, NULL, "marvell,ap806-cpu-clock"); + if (!node || !of_device_is_available(node)) + return -ENODEV; + + nb_cpus = num_possible_cpus(); + freq_tables = kcalloc(nb_cpus, sizeof(*freq_tables), GFP_KERNEL); + cpumask_copy(&cpus, cpu_possible_mask); + + /* + * For each CPU, this loop registers the operating points + * supported (which are the nominal CPU frequency and full integer + * divisions of it). + */ + for_each_cpu(cpu, &cpus) { + struct cpumask shared_cpus; + struct device *cpu_dev; + struct clk *clk; + + cpu_dev = get_cpu_device(cpu); + + if (!cpu_dev) { + pr_err("Cannot get CPU %d\n", cpu); + continue; + } + + clk = clk_get(cpu_dev, 0); + + if (IS_ERR(clk)) { + pr_err("Cannot get clock for CPU %d\n", cpu); + ret = PTR_ERR(clk); + goto remove_opp; + } + + ret = armada_8k_add_opp(clk, cpu_dev, freq_tables, opps_index); + if (ret) { + clk_put(clk); + goto remove_opp; + } + + opps_index++; + cpumask_clear(&shared_cpus); + armada_8k_get_sharing_cpus(clk, &shared_cpus); + dev_pm_opp_set_sharing_cpus(cpu_dev, &shared_cpus); + cpumask_andnot(&cpus, &cpus, &shared_cpus); + clk_put(clk); + } + + armada_8k_pdev = platform_device_register_simple("cpufreq-dt", -1, + NULL, 0); + ret = PTR_ERR_OR_ZERO(armada_8k_pdev); + if (ret) + goto remove_opp; + + platform_set_drvdata(armada_8k_pdev, freq_tables); + + return 0; + +remove_opp: + armada_8k_cpufreq_free_table(freq_tables); + return ret; +} +module_init(armada_8k_cpufreq_init); + +static void __exit armada_8k_cpufreq_exit(void) +{ + struct freq_table *freq_tables = platform_get_drvdata(armada_8k_pdev); + + armada_8k_cpufreq_free_table(freq_tables); + platform_device_unregister(armada_8k_pdev); +} +module_exit(armada_8k_cpufreq_exit); + +MODULE_AUTHOR("Gregory Clement <gregory.clement@bootlin.com>"); +MODULE_DESCRIPTION("Armada 8K cpufreq driver"); +MODULE_LICENSE("GPL"); -- 2.20.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v5 2/2] cpufreq: ap806: add cpufreq driver for Armada 8K 2019-01-18 14:11 ` Gregory CLEMENT @ 2019-01-18 14:51 ` Gregory CLEMENT -1 siblings, 0 replies; 10+ messages in thread From: Gregory CLEMENT @ 2019-01-18 14:51 UTC (permalink / raw) To: Rafael J. Wysocki, Viresh Kumar, linux-pm Cc: Andrew Lunn, Jason Cooper, Antoine Tenart, Gregory CLEMENT, Maxime Chevallier, Thomas Petazzoni, Miquèl Raynal, linux-arm-kernel, Sebastian Hesselbarth Add cpufreq driver for Marvell AP-806 found on Aramda 8K. The AP-806 has DFS (Dynamic Frequency Scaling) with coupled clock domain for two clusters, so this driver will directly use generic cpufreq-dt driver as backend. Based on the work of Omri Itach <omrii@marvell.com>. Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> --- Hi, This one is the correct version, in the previous one the change were not merged. Sorry for the noise, Gregory drivers/cpufreq/Kconfig.arm | 11 ++ drivers/cpufreq/Makefile | 1 + drivers/cpufreq/armada-8k-cpufreq.c | 204 ++++++++++++++++++++++++++++ 3 files changed, 216 insertions(+) create mode 100644 drivers/cpufreq/armada-8k-cpufreq.c diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm index 688f10227793..10bc5c798d17 100644 --- a/drivers/cpufreq/Kconfig.arm +++ b/drivers/cpufreq/Kconfig.arm @@ -25,6 +25,17 @@ config ARM_ARMADA_37XX_CPUFREQ This adds the CPUFreq driver support for Marvell Armada 37xx SoCs. The Armada 37xx PMU supports 4 frequency and VDD levels. +config ARM_ARMADA_8K_CPUFREQ + tristate "Armada 8K CPUFreq driver" + depends on ARCH_MVEBU && CPUFREQ_DT + help + This enables the CPUFreq driver support for Marvell + Armada8k SOCs. + Armada8K device has the AP806 which supports scaling + to any full integer divider. + + If in doubt, say N. + # big LITTLE core layer and glue drivers config ARM_BIG_LITTLE_CPUFREQ tristate "Generic ARM big LITTLE CPUfreq driver" diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile index 08c071be2491..689b26c6f949 100644 --- a/drivers/cpufreq/Makefile +++ b/drivers/cpufreq/Makefile @@ -50,6 +50,7 @@ obj-$(CONFIG_X86_SFI_CPUFREQ) += sfi-cpufreq.o obj-$(CONFIG_ARM_BIG_LITTLE_CPUFREQ) += arm_big_little.o obj-$(CONFIG_ARM_ARMADA_37XX_CPUFREQ) += armada-37xx-cpufreq.o +obj-$(CONFIG_ARM_ARMADA_8K_CPUFREQ) += armada-8k-cpufreq.o obj-$(CONFIG_ARM_BRCMSTB_AVS_CPUFREQ) += brcmstb-avs-cpufreq.o obj-$(CONFIG_ACPI_CPPC_CPUFREQ) += cppc_cpufreq.o obj-$(CONFIG_ARCH_DAVINCI) += davinci-cpufreq.o diff --git a/drivers/cpufreq/armada-8k-cpufreq.c b/drivers/cpufreq/armada-8k-cpufreq.c new file mode 100644 index 000000000000..8a5ddb93fc58 --- /dev/null +++ b/drivers/cpufreq/armada-8k-cpufreq.c @@ -0,0 +1,204 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * CPUFreq support for Armada 8K + * + * Copyright (C) 2018 Marvell + * + * Omri Itach <omrii@marvell.com> + * Gregory Clement <gregory.clement@bootlin.com> + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#include <linux/clk.h> +#include <linux/cpu.h> +#include <linux/err.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/pm_opp.h> +#include <linux/slab.h> + +/* + * Setup the opps list with the divider for the max frequency, that + * will be filled at runtime. + */ +static const int opps_div[] __initconst = {1, 2, 3, 4}; + +static struct platform_device *armada_8k_pdev; + +struct freq_table { + struct device *cpu_dev; + unsigned int freq[ARRAY_SIZE(opps_div)]; +}; + +/* If the CPUs share the same clock, then they are in the same cluster. */ +static void __init armada_8k_get_sharing_cpus(struct clk *cur_clk, + struct cpumask *cpumask) +{ + int cpu; + + for_each_possible_cpu(cpu) { + struct device *cpu_dev; + struct clk *clk; + + cpu_dev = get_cpu_device(cpu); + if (!cpu_dev) { + pr_warn("Failed to get cpu%d device\n", cpu); + continue; + } + + clk = clk_get(cpu_dev, 0); + if (IS_ERR(clk)) { + pr_warn("Cannot get clock for CPU %d\n", cpu); + } else { + if (clk_is_match(clk, cur_clk)) + cpumask_set_cpu(cpu, cpumask); + + clk_put(clk); + } + } +} + +static int __init armada_8k_add_opp(struct clk *clk, struct device *cpu_dev, + struct freq_table *freq_tables, + int opps_index) +{ + unsigned int cur_frequency; + unsigned int freq; + int i, ret; + + /* Get nominal (current) CPU frequency. */ + cur_frequency = clk_get_rate(clk); + if (!cur_frequency) { + dev_err(cpu_dev, "Failed to get clock rate for this CPU\n"); + return -EINVAL; + } + + freq_tables[opps_index].cpu_dev = cpu_dev; + + for (i = 0; i < ARRAY_SIZE(opps_div); i++) { + freq = cur_frequency / opps_div[i]; + + ret = dev_pm_opp_add(cpu_dev, freq, 0); + if (ret) + return ret; + + freq_tables[opps_index].freq[i] = freq; + } + + return 0; +} + +static void armada_8k_cpufreq_free_table(struct freq_table *freq_tables) +{ + int opps_index, nb_cpus = num_possible_cpus(); + + for (opps_index = 0 ; opps_index <= nb_cpus; opps_index++) { + int i; + + /* If cpu_dev is NULL then we reached the end of the array */ + if (!freq_tables[opps_index].cpu_dev) + break; + + for (i = 0; i < ARRAY_SIZE(opps_div); i++) { + /* + * A 0Hz frequency is not valid, this meant + * that it was not yet initialized so there is + * no more opp to free + */ + if (freq_tables[opps_index].freq[i] == 0) + break; + + dev_pm_opp_remove(freq_tables[opps_index].cpu_dev, + freq_tables[opps_index].freq[i]); + } + } + + kfree(freq_tables); +} + +static int __init armada_8k_cpufreq_init(void) +{ + int ret = 0, opps_index = 0, cpu, nb_cpus; + struct freq_table *freq_tables; + struct device_node *node; + struct cpumask cpus; + + node = of_find_compatible_node(NULL, NULL, "marvell,ap806-cpu-clock"); + if (!node || !of_device_is_available(node)) + return -ENODEV; + + nb_cpus = num_possible_cpus(); + freq_tables = kcalloc(nb_cpus, sizeof(*freq_tables), GFP_KERNEL); + cpumask_copy(&cpus, cpu_possible_mask); + + /* + * For each CPU, this loop registers the operating points + * supported (which are the nominal CPU frequency and full integer + * divisions of it). + */ + for_each_cpu(cpu, &cpus) { + struct cpumask shared_cpus; + struct device *cpu_dev; + struct clk *clk; + + cpu_dev = get_cpu_device(cpu); + + if (!cpu_dev) { + pr_err("Cannot get CPU %d\n", cpu); + continue; + } + + clk = clk_get(cpu_dev, 0); + + if (IS_ERR(clk)) { + pr_err("Cannot get clock for CPU %d\n", cpu); + ret = PTR_ERR(clk); + goto remove_opp; + } + + ret = armada_8k_add_opp(clk, cpu_dev, freq_tables, opps_index); + if (ret) { + clk_put(clk); + goto remove_opp; + } + + opps_index++; + cpumask_clear(&shared_cpus); + armada_8k_get_sharing_cpus(clk, &shared_cpus); + dev_pm_opp_set_sharing_cpus(cpu_dev, &shared_cpus); + cpumask_andnot(&cpus, &cpus, &shared_cpus); + clk_put(clk); + } + + armada_8k_pdev = platform_device_register_simple("cpufreq-dt", -1, + NULL, 0); + ret = PTR_ERR_OR_ZERO(armada_8k_pdev); + if (ret) + goto remove_opp; + + platform_set_drvdata(armada_8k_pdev, freq_tables); + + return 0; + +remove_opp: + armada_8k_cpufreq_free_table(freq_tables); + return ret; +} +module_init(armada_8k_cpufreq_init); + +static void __exit armada_8k_cpufreq_exit(void) +{ + struct freq_table *freq_tables = platform_get_drvdata(armada_8k_pdev); + + platform_device_unregister(armada_8k_pdev); + armada_8k_cpufreq_free_table(freq_tables); +} +module_exit(armada_8k_cpufreq_exit); + +MODULE_AUTHOR("Gregory Clement <gregory.clement@bootlin.com>"); +MODULE_DESCRIPTION("Armada 8K cpufreq driver"); +MODULE_LICENSE("GPL"); -- 2.20.1 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v5 2/2] cpufreq: ap806: add cpufreq driver for Armada 8K @ 2019-01-18 14:51 ` Gregory CLEMENT 0 siblings, 0 replies; 10+ messages in thread From: Gregory CLEMENT @ 2019-01-18 14:51 UTC (permalink / raw) To: Rafael J. Wysocki, Viresh Kumar, linux-pm Cc: Andrew Lunn, Jason Cooper, Antoine Tenart, Gregory CLEMENT, Maxime Chevallier, Thomas Petazzoni, Miquèl Raynal, linux-arm-kernel, Sebastian Hesselbarth Add cpufreq driver for Marvell AP-806 found on Aramda 8K. The AP-806 has DFS (Dynamic Frequency Scaling) with coupled clock domain for two clusters, so this driver will directly use generic cpufreq-dt driver as backend. Based on the work of Omri Itach <omrii@marvell.com>. Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> --- Hi, This one is the correct version, in the previous one the change were not merged. Sorry for the noise, Gregory drivers/cpufreq/Kconfig.arm | 11 ++ drivers/cpufreq/Makefile | 1 + drivers/cpufreq/armada-8k-cpufreq.c | 204 ++++++++++++++++++++++++++++ 3 files changed, 216 insertions(+) create mode 100644 drivers/cpufreq/armada-8k-cpufreq.c diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm index 688f10227793..10bc5c798d17 100644 --- a/drivers/cpufreq/Kconfig.arm +++ b/drivers/cpufreq/Kconfig.arm @@ -25,6 +25,17 @@ config ARM_ARMADA_37XX_CPUFREQ This adds the CPUFreq driver support for Marvell Armada 37xx SoCs. The Armada 37xx PMU supports 4 frequency and VDD levels. +config ARM_ARMADA_8K_CPUFREQ + tristate "Armada 8K CPUFreq driver" + depends on ARCH_MVEBU && CPUFREQ_DT + help + This enables the CPUFreq driver support for Marvell + Armada8k SOCs. + Armada8K device has the AP806 which supports scaling + to any full integer divider. + + If in doubt, say N. + # big LITTLE core layer and glue drivers config ARM_BIG_LITTLE_CPUFREQ tristate "Generic ARM big LITTLE CPUfreq driver" diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile index 08c071be2491..689b26c6f949 100644 --- a/drivers/cpufreq/Makefile +++ b/drivers/cpufreq/Makefile @@ -50,6 +50,7 @@ obj-$(CONFIG_X86_SFI_CPUFREQ) += sfi-cpufreq.o obj-$(CONFIG_ARM_BIG_LITTLE_CPUFREQ) += arm_big_little.o obj-$(CONFIG_ARM_ARMADA_37XX_CPUFREQ) += armada-37xx-cpufreq.o +obj-$(CONFIG_ARM_ARMADA_8K_CPUFREQ) += armada-8k-cpufreq.o obj-$(CONFIG_ARM_BRCMSTB_AVS_CPUFREQ) += brcmstb-avs-cpufreq.o obj-$(CONFIG_ACPI_CPPC_CPUFREQ) += cppc_cpufreq.o obj-$(CONFIG_ARCH_DAVINCI) += davinci-cpufreq.o diff --git a/drivers/cpufreq/armada-8k-cpufreq.c b/drivers/cpufreq/armada-8k-cpufreq.c new file mode 100644 index 000000000000..8a5ddb93fc58 --- /dev/null +++ b/drivers/cpufreq/armada-8k-cpufreq.c @@ -0,0 +1,204 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * CPUFreq support for Armada 8K + * + * Copyright (C) 2018 Marvell + * + * Omri Itach <omrii@marvell.com> + * Gregory Clement <gregory.clement@bootlin.com> + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#include <linux/clk.h> +#include <linux/cpu.h> +#include <linux/err.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/pm_opp.h> +#include <linux/slab.h> + +/* + * Setup the opps list with the divider for the max frequency, that + * will be filled at runtime. + */ +static const int opps_div[] __initconst = {1, 2, 3, 4}; + +static struct platform_device *armada_8k_pdev; + +struct freq_table { + struct device *cpu_dev; + unsigned int freq[ARRAY_SIZE(opps_div)]; +}; + +/* If the CPUs share the same clock, then they are in the same cluster. */ +static void __init armada_8k_get_sharing_cpus(struct clk *cur_clk, + struct cpumask *cpumask) +{ + int cpu; + + for_each_possible_cpu(cpu) { + struct device *cpu_dev; + struct clk *clk; + + cpu_dev = get_cpu_device(cpu); + if (!cpu_dev) { + pr_warn("Failed to get cpu%d device\n", cpu); + continue; + } + + clk = clk_get(cpu_dev, 0); + if (IS_ERR(clk)) { + pr_warn("Cannot get clock for CPU %d\n", cpu); + } else { + if (clk_is_match(clk, cur_clk)) + cpumask_set_cpu(cpu, cpumask); + + clk_put(clk); + } + } +} + +static int __init armada_8k_add_opp(struct clk *clk, struct device *cpu_dev, + struct freq_table *freq_tables, + int opps_index) +{ + unsigned int cur_frequency; + unsigned int freq; + int i, ret; + + /* Get nominal (current) CPU frequency. */ + cur_frequency = clk_get_rate(clk); + if (!cur_frequency) { + dev_err(cpu_dev, "Failed to get clock rate for this CPU\n"); + return -EINVAL; + } + + freq_tables[opps_index].cpu_dev = cpu_dev; + + for (i = 0; i < ARRAY_SIZE(opps_div); i++) { + freq = cur_frequency / opps_div[i]; + + ret = dev_pm_opp_add(cpu_dev, freq, 0); + if (ret) + return ret; + + freq_tables[opps_index].freq[i] = freq; + } + + return 0; +} + +static void armada_8k_cpufreq_free_table(struct freq_table *freq_tables) +{ + int opps_index, nb_cpus = num_possible_cpus(); + + for (opps_index = 0 ; opps_index <= nb_cpus; opps_index++) { + int i; + + /* If cpu_dev is NULL then we reached the end of the array */ + if (!freq_tables[opps_index].cpu_dev) + break; + + for (i = 0; i < ARRAY_SIZE(opps_div); i++) { + /* + * A 0Hz frequency is not valid, this meant + * that it was not yet initialized so there is + * no more opp to free + */ + if (freq_tables[opps_index].freq[i] == 0) + break; + + dev_pm_opp_remove(freq_tables[opps_index].cpu_dev, + freq_tables[opps_index].freq[i]); + } + } + + kfree(freq_tables); +} + +static int __init armada_8k_cpufreq_init(void) +{ + int ret = 0, opps_index = 0, cpu, nb_cpus; + struct freq_table *freq_tables; + struct device_node *node; + struct cpumask cpus; + + node = of_find_compatible_node(NULL, NULL, "marvell,ap806-cpu-clock"); + if (!node || !of_device_is_available(node)) + return -ENODEV; + + nb_cpus = num_possible_cpus(); + freq_tables = kcalloc(nb_cpus, sizeof(*freq_tables), GFP_KERNEL); + cpumask_copy(&cpus, cpu_possible_mask); + + /* + * For each CPU, this loop registers the operating points + * supported (which are the nominal CPU frequency and full integer + * divisions of it). + */ + for_each_cpu(cpu, &cpus) { + struct cpumask shared_cpus; + struct device *cpu_dev; + struct clk *clk; + + cpu_dev = get_cpu_device(cpu); + + if (!cpu_dev) { + pr_err("Cannot get CPU %d\n", cpu); + continue; + } + + clk = clk_get(cpu_dev, 0); + + if (IS_ERR(clk)) { + pr_err("Cannot get clock for CPU %d\n", cpu); + ret = PTR_ERR(clk); + goto remove_opp; + } + + ret = armada_8k_add_opp(clk, cpu_dev, freq_tables, opps_index); + if (ret) { + clk_put(clk); + goto remove_opp; + } + + opps_index++; + cpumask_clear(&shared_cpus); + armada_8k_get_sharing_cpus(clk, &shared_cpus); + dev_pm_opp_set_sharing_cpus(cpu_dev, &shared_cpus); + cpumask_andnot(&cpus, &cpus, &shared_cpus); + clk_put(clk); + } + + armada_8k_pdev = platform_device_register_simple("cpufreq-dt", -1, + NULL, 0); + ret = PTR_ERR_OR_ZERO(armada_8k_pdev); + if (ret) + goto remove_opp; + + platform_set_drvdata(armada_8k_pdev, freq_tables); + + return 0; + +remove_opp: + armada_8k_cpufreq_free_table(freq_tables); + return ret; +} +module_init(armada_8k_cpufreq_init); + +static void __exit armada_8k_cpufreq_exit(void) +{ + struct freq_table *freq_tables = platform_get_drvdata(armada_8k_pdev); + + platform_device_unregister(armada_8k_pdev); + armada_8k_cpufreq_free_table(freq_tables); +} +module_exit(armada_8k_cpufreq_exit); + +MODULE_AUTHOR("Gregory Clement <gregory.clement@bootlin.com>"); +MODULE_DESCRIPTION("Armada 8K cpufreq driver"); +MODULE_LICENSE("GPL"); -- 2.20.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH v5 0/2] Add cpufreq support for Armada 8K 2019-01-18 14:11 ` Gregory CLEMENT @ 2019-01-23 10:08 ` Viresh Kumar -1 siblings, 0 replies; 10+ messages in thread From: Viresh Kumar @ 2019-01-23 10:08 UTC (permalink / raw) To: Gregory CLEMENT Cc: Andrew Lunn, Jason Cooper, linux-pm, Antoine Tenart, Rafael J. Wysocki, Maxime Chevallier, Thomas Petazzoni, Miquèl Raynal, linux-arm-kernel, Sebastian Hesselbarth On 18-01-19, 15:11, Gregory CLEMENT wrote: > Hi, > > this is the fifth version of a the series adding the cpufreq support > for the Marvell Armada 8K SoCs. Applied. Thanks. -- viresh ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v5 0/2] Add cpufreq support for Armada 8K @ 2019-01-23 10:08 ` Viresh Kumar 0 siblings, 0 replies; 10+ messages in thread From: Viresh Kumar @ 2019-01-23 10:08 UTC (permalink / raw) To: Gregory CLEMENT Cc: Andrew Lunn, Jason Cooper, linux-pm, Antoine Tenart, Rafael J. Wysocki, Maxime Chevallier, Thomas Petazzoni, Miquèl Raynal, linux-arm-kernel, Sebastian Hesselbarth On 18-01-19, 15:11, Gregory CLEMENT wrote: > Hi, > > this is the fifth version of a the series adding the cpufreq support > for the Marvell Armada 8K SoCs. Applied. Thanks. -- viresh _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2019-01-23 10:08 UTC | newest] Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2019-01-18 14:11 [PATCH v5 0/2] Add cpufreq support for Armada 8K Gregory CLEMENT 2019-01-18 14:11 ` Gregory CLEMENT 2019-01-18 14:11 ` [PATCH v5 1/2] MAINTAINERS: add new entries for Armada 8K cpufreq driver Gregory CLEMENT 2019-01-18 14:11 ` Gregory CLEMENT 2019-01-18 14:11 ` [PATCH v5 2/2] cpufreq: ap806: add cpufreq driver for Armada 8K Gregory CLEMENT 2019-01-18 14:11 ` Gregory CLEMENT 2019-01-18 14:51 ` Gregory CLEMENT 2019-01-18 14:51 ` Gregory CLEMENT 2019-01-23 10:08 ` [PATCH v5 0/2] Add cpufreq support " Viresh Kumar 2019-01-23 10:08 ` Viresh Kumar
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.