* [PATCH v5 0/2] Add cpufreq support for Armada 8K
@ 2019-01-18 14:11 ` Gregory CLEMENT
0 siblings, 0 replies; 10+ messages in thread
From: Gregory CLEMENT @ 2019-01-18 14:11 UTC (permalink / raw)
To: Rafael J. Wysocki, Viresh Kumar, linux-pm
Cc: Andrew Lunn, Jason Cooper, Antoine Tenart, Gregory CLEMENT,
Maxime Chevallier, Thomas Petazzoni, Miquèl Raynal,
linux-arm-kernel, Sebastian Hesselbarth
Hi,
this is the fifth version of a the series adding the cpufreq support
for the Marvell Armada 8K SoCs.
Gregory
Changelog:
v4 -> v5:
- Rebased onto v5.0-rc1
- Rewrite the clk_get part in armada_8k_get_sharing_cpus()
- Reverse the call function order in armada_8k_cpufreq_exit()
v3 -> v4:
- Remove most of the global variable and use the private data of the
platfrom device to store the freq_tables struct.
- Remove the clk pointer of the freq_table struct which is no more
needed with the new way to register the opp
- Check the get_cpu_device() return.
- Balance the clk_get() calls.
- No more use the devm_ function.
- Base the registration of the opp on the cpu mask updated after each
iteration to find the shared cpus.
- Base the free on the NULL or 0 value of the freq_table struct
members, it allows to remove the global index.
v2 -> v3
- Make the driver really modular (modprobe;modprobe -r;modprobe; is working)
- Don't use anymore 100MHz as minimal frequency, but only max frequency/4
- Fix remaining warning reported by checkpatch
- Rework the registering of the opp
v1 -> v2:
- Fix typos in MAINTAINERS (reported by Baruch Siach) and in
armada-8k-cpufreq.c (reported by Thomas Petazzoni)
- Fix indentation in Kconfig.arm (reported by Thomas Petazzoni)
- Use const for opps_div (reported by Thomas Petazzoni)
- Fix memory leak of opps_array (reported by Thomas Petazzoni)
Gregory CLEMENT (2):
MAINTAINERS: add new entries for Armada 8K cpufreq driver
cpufreq: ap806: add cpufreq driver for Armada 8K
MAINTAINERS | 1 +
drivers/cpufreq/Kconfig.arm | 11 ++
drivers/cpufreq/Makefile | 1 +
drivers/cpufreq/armada-8k-cpufreq.c | 203 ++++++++++++++++++++++++++++
4 files changed, 216 insertions(+)
create mode 100644 drivers/cpufreq/armada-8k-cpufreq.c
--
2.20.1
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v5 0/2] Add cpufreq support for Armada 8K
@ 2019-01-18 14:11 ` Gregory CLEMENT
0 siblings, 0 replies; 10+ messages in thread
From: Gregory CLEMENT @ 2019-01-18 14:11 UTC (permalink / raw)
To: Rafael J. Wysocki, Viresh Kumar, linux-pm
Cc: Andrew Lunn, Jason Cooper, Antoine Tenart, Gregory CLEMENT,
Maxime Chevallier, Thomas Petazzoni, Miquèl Raynal,
linux-arm-kernel, Sebastian Hesselbarth
Hi,
this is the fifth version of a the series adding the cpufreq support
for the Marvell Armada 8K SoCs.
Gregory
Changelog:
v4 -> v5:
- Rebased onto v5.0-rc1
- Rewrite the clk_get part in armada_8k_get_sharing_cpus()
- Reverse the call function order in armada_8k_cpufreq_exit()
v3 -> v4:
- Remove most of the global variable and use the private data of the
platfrom device to store the freq_tables struct.
- Remove the clk pointer of the freq_table struct which is no more
needed with the new way to register the opp
- Check the get_cpu_device() return.
- Balance the clk_get() calls.
- No more use the devm_ function.
- Base the registration of the opp on the cpu mask updated after each
iteration to find the shared cpus.
- Base the free on the NULL or 0 value of the freq_table struct
members, it allows to remove the global index.
v2 -> v3
- Make the driver really modular (modprobe;modprobe -r;modprobe; is working)
- Don't use anymore 100MHz as minimal frequency, but only max frequency/4
- Fix remaining warning reported by checkpatch
- Rework the registering of the opp
v1 -> v2:
- Fix typos in MAINTAINERS (reported by Baruch Siach) and in
armada-8k-cpufreq.c (reported by Thomas Petazzoni)
- Fix indentation in Kconfig.arm (reported by Thomas Petazzoni)
- Use const for opps_div (reported by Thomas Petazzoni)
- Fix memory leak of opps_array (reported by Thomas Petazzoni)
Gregory CLEMENT (2):
MAINTAINERS: add new entries for Armada 8K cpufreq driver
cpufreq: ap806: add cpufreq driver for Armada 8K
MAINTAINERS | 1 +
drivers/cpufreq/Kconfig.arm | 11 ++
drivers/cpufreq/Makefile | 1 +
drivers/cpufreq/armada-8k-cpufreq.c | 203 ++++++++++++++++++++++++++++
4 files changed, 216 insertions(+)
create mode 100644 drivers/cpufreq/armada-8k-cpufreq.c
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v5 1/2] MAINTAINERS: add new entries for Armada 8K cpufreq driver
2019-01-18 14:11 ` Gregory CLEMENT
@ 2019-01-18 14:11 ` Gregory CLEMENT
-1 siblings, 0 replies; 10+ messages in thread
From: Gregory CLEMENT @ 2019-01-18 14:11 UTC (permalink / raw)
To: Rafael J. Wysocki, Viresh Kumar, linux-pm
Cc: Andrew Lunn, Jason Cooper, Antoine Tenart, Gregory CLEMENT,
Maxime Chevallier, Thomas Petazzoni, Miquèl Raynal,
linux-arm-kernel, Sebastian Hesselbarth
This new driver belongs to the mvebu family, update the MAINTAINER file
to document it.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
---
MAINTAINERS | 1 +
1 file changed, 1 insertion(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index 32d444476a90..4a3d62a83e35 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1737,6 +1737,7 @@ F: arch/arm/configs/mvebu_*_defconfig
F: arch/arm/mach-mvebu/
F: arch/arm64/boot/dts/marvell/armada*
F: drivers/cpufreq/armada-37xx-cpufreq.c
+F: drivers/cpufreq/armada-8k-cpufreq.c
F: drivers/cpufreq/mvebu-cpufreq.c
F: drivers/irqchip/irq-armada-370-xp.c
F: drivers/irqchip/irq-mvebu-*
--
2.20.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v5 1/2] MAINTAINERS: add new entries for Armada 8K cpufreq driver
@ 2019-01-18 14:11 ` Gregory CLEMENT
0 siblings, 0 replies; 10+ messages in thread
From: Gregory CLEMENT @ 2019-01-18 14:11 UTC (permalink / raw)
To: Rafael J. Wysocki, Viresh Kumar, linux-pm
Cc: Andrew Lunn, Jason Cooper, Antoine Tenart, Gregory CLEMENT,
Maxime Chevallier, Thomas Petazzoni, Miquèl Raynal,
linux-arm-kernel, Sebastian Hesselbarth
This new driver belongs to the mvebu family, update the MAINTAINER file
to document it.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
---
MAINTAINERS | 1 +
1 file changed, 1 insertion(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index 32d444476a90..4a3d62a83e35 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1737,6 +1737,7 @@ F: arch/arm/configs/mvebu_*_defconfig
F: arch/arm/mach-mvebu/
F: arch/arm64/boot/dts/marvell/armada*
F: drivers/cpufreq/armada-37xx-cpufreq.c
+F: drivers/cpufreq/armada-8k-cpufreq.c
F: drivers/cpufreq/mvebu-cpufreq.c
F: drivers/irqchip/irq-armada-370-xp.c
F: drivers/irqchip/irq-mvebu-*
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v5 2/2] cpufreq: ap806: add cpufreq driver for Armada 8K
2019-01-18 14:11 ` Gregory CLEMENT
@ 2019-01-18 14:11 ` Gregory CLEMENT
-1 siblings, 0 replies; 10+ messages in thread
From: Gregory CLEMENT @ 2019-01-18 14:11 UTC (permalink / raw)
To: Rafael J. Wysocki, Viresh Kumar, linux-pm
Cc: Andrew Lunn, Jason Cooper, Antoine Tenart, Gregory CLEMENT,
Maxime Chevallier, Thomas Petazzoni, Miquèl Raynal,
linux-arm-kernel, Sebastian Hesselbarth
Add cpufreq driver for Marvell AP-806 found on Aramda 8K.
The AP-806 has DFS (Dynamic Frequency Scaling) with coupled
clock domain for two clusters, so this driver will directly
use generic cpufreq-dt driver as backend.
Based on the work of Omri Itach <omrii@marvell.com>.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
---
drivers/cpufreq/Kconfig.arm | 11 ++
drivers/cpufreq/Makefile | 1 +
drivers/cpufreq/armada-8k-cpufreq.c | 203 ++++++++++++++++++++++++++++
3 files changed, 215 insertions(+)
create mode 100644 drivers/cpufreq/armada-8k-cpufreq.c
diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
index 688f10227793..10bc5c798d17 100644
--- a/drivers/cpufreq/Kconfig.arm
+++ b/drivers/cpufreq/Kconfig.arm
@@ -25,6 +25,17 @@ config ARM_ARMADA_37XX_CPUFREQ
This adds the CPUFreq driver support for Marvell Armada 37xx SoCs.
The Armada 37xx PMU supports 4 frequency and VDD levels.
+config ARM_ARMADA_8K_CPUFREQ
+ tristate "Armada 8K CPUFreq driver"
+ depends on ARCH_MVEBU && CPUFREQ_DT
+ help
+ This enables the CPUFreq driver support for Marvell
+ Armada8k SOCs.
+ Armada8K device has the AP806 which supports scaling
+ to any full integer divider.
+
+ If in doubt, say N.
+
# big LITTLE core layer and glue drivers
config ARM_BIG_LITTLE_CPUFREQ
tristate "Generic ARM big LITTLE CPUfreq driver"
diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
index 08c071be2491..689b26c6f949 100644
--- a/drivers/cpufreq/Makefile
+++ b/drivers/cpufreq/Makefile
@@ -50,6 +50,7 @@ obj-$(CONFIG_X86_SFI_CPUFREQ) += sfi-cpufreq.o
obj-$(CONFIG_ARM_BIG_LITTLE_CPUFREQ) += arm_big_little.o
obj-$(CONFIG_ARM_ARMADA_37XX_CPUFREQ) += armada-37xx-cpufreq.o
+obj-$(CONFIG_ARM_ARMADA_8K_CPUFREQ) += armada-8k-cpufreq.o
obj-$(CONFIG_ARM_BRCMSTB_AVS_CPUFREQ) += brcmstb-avs-cpufreq.o
obj-$(CONFIG_ACPI_CPPC_CPUFREQ) += cppc_cpufreq.o
obj-$(CONFIG_ARCH_DAVINCI) += davinci-cpufreq.o
diff --git a/drivers/cpufreq/armada-8k-cpufreq.c b/drivers/cpufreq/armada-8k-cpufreq.c
new file mode 100644
index 000000000000..80375de4e149
--- /dev/null
+++ b/drivers/cpufreq/armada-8k-cpufreq.c
@@ -0,0 +1,203 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * CPUFreq support for Armada 8K
+ *
+ * Copyright (C) 2018 Marvell
+ *
+ * Omri Itach <omrii@marvell.com>
+ * Gregory Clement <gregory.clement@bootlin.com>
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/clk.h>
+#include <linux/cpu.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_opp.h>
+#include <linux/slab.h>
+
+/*
+ * Setup the opps list with the divider for the max frequency, that
+ * will be filled at runtime.
+ */
+static const int opps_div[] __initconst = {1, 2, 3, 4};
+
+static struct platform_device *armada_8k_pdev;
+
+struct freq_table {
+ struct device *cpu_dev;
+ unsigned int freq[ARRAY_SIZE(opps_div)];
+};
+
+/* If the CPUs share the same clock, then they are in the same cluster. */
+static void __init armada_8k_get_sharing_cpus(struct clk *cur_clk,
+ struct cpumask *cpumask)
+{
+ int cpu;
+
+ for_each_possible_cpu(cpu) {
+ struct device *cpu_dev;
+ struct clk *clk;
+
+ cpu_dev = get_cpu_device(cpu);
+ if (!cpu_dev) {
+ pr_warn("Failed to get cpu%d device\n", cpu);
+ continue;
+ }
+
+ clk = clk_get(cpu_dev, 0);
+ if (IS_ERR(clk))
+ pr_warn("Cannot get clock for CPU %d\n", cpu);
+ else if (clk_is_match(clk, cur_clk))
+ cpumask_set_cpu(cpu, cpumask);
+
+ if (!IS_ERR(clk))
+ clk_put(clk);
+ }
+}
+
+static int __init armada_8k_add_opp(struct clk *clk, struct device *cpu_dev,
+ struct freq_table *freq_tables,
+ int opps_index)
+{
+ unsigned int cur_frequency;
+ unsigned int freq;
+ int i, ret;
+
+ /* Get nominal (current) CPU frequency. */
+ cur_frequency = clk_get_rate(clk);
+ if (!cur_frequency) {
+ dev_err(cpu_dev, "Failed to get clock rate for this CPU\n");
+ return -EINVAL;
+ }
+
+ freq_tables[opps_index].cpu_dev = cpu_dev;
+
+ for (i = 0; i < ARRAY_SIZE(opps_div); i++) {
+ freq = cur_frequency / opps_div[i];
+
+ ret = dev_pm_opp_add(cpu_dev, freq, 0);
+ if (ret)
+ return ret;
+
+ freq_tables[opps_index].freq[i] = freq;
+ }
+
+ return 0;
+}
+
+static void armada_8k_cpufreq_free_table(struct freq_table *freq_tables)
+{
+ int opps_index, nb_cpus = num_possible_cpus();
+
+ for (opps_index = 0 ; opps_index <= nb_cpus; opps_index++) {
+ int i;
+
+ /* If cpu_dev is NULL then we reached the end of the array */
+ if (!freq_tables[opps_index].cpu_dev)
+ break;
+
+ for (i = 0; i < ARRAY_SIZE(opps_div); i++) {
+ /*
+ * A 0Hz frequency is not valid, this meant
+ * that it was not yet initialized so there is
+ * no more opp to free
+ */
+ if (freq_tables[opps_index].freq[i] == 0)
+ break;
+
+ dev_pm_opp_remove(freq_tables[opps_index].cpu_dev,
+ freq_tables[opps_index].freq[i]);
+ }
+ }
+
+ kfree(freq_tables);
+}
+
+static int __init armada_8k_cpufreq_init(void)
+{
+ int ret = 0, opps_index = 0, cpu, nb_cpus;
+ struct freq_table *freq_tables;
+ struct device_node *node;
+ struct cpumask cpus;
+
+ node = of_find_compatible_node(NULL, NULL, "marvell,ap806-cpu-clock");
+ if (!node || !of_device_is_available(node))
+ return -ENODEV;
+
+ nb_cpus = num_possible_cpus();
+ freq_tables = kcalloc(nb_cpus, sizeof(*freq_tables), GFP_KERNEL);
+ cpumask_copy(&cpus, cpu_possible_mask);
+
+ /*
+ * For each CPU, this loop registers the operating points
+ * supported (which are the nominal CPU frequency and full integer
+ * divisions of it).
+ */
+ for_each_cpu(cpu, &cpus) {
+ struct cpumask shared_cpus;
+ struct device *cpu_dev;
+ struct clk *clk;
+
+ cpu_dev = get_cpu_device(cpu);
+
+ if (!cpu_dev) {
+ pr_err("Cannot get CPU %d\n", cpu);
+ continue;
+ }
+
+ clk = clk_get(cpu_dev, 0);
+
+ if (IS_ERR(clk)) {
+ pr_err("Cannot get clock for CPU %d\n", cpu);
+ ret = PTR_ERR(clk);
+ goto remove_opp;
+ }
+
+ ret = armada_8k_add_opp(clk, cpu_dev, freq_tables, opps_index);
+ if (ret) {
+ clk_put(clk);
+ goto remove_opp;
+ }
+
+ opps_index++;
+ cpumask_clear(&shared_cpus);
+ armada_8k_get_sharing_cpus(clk, &shared_cpus);
+ dev_pm_opp_set_sharing_cpus(cpu_dev, &shared_cpus);
+ cpumask_andnot(&cpus, &cpus, &shared_cpus);
+ clk_put(clk);
+ }
+
+ armada_8k_pdev = platform_device_register_simple("cpufreq-dt", -1,
+ NULL, 0);
+ ret = PTR_ERR_OR_ZERO(armada_8k_pdev);
+ if (ret)
+ goto remove_opp;
+
+ platform_set_drvdata(armada_8k_pdev, freq_tables);
+
+ return 0;
+
+remove_opp:
+ armada_8k_cpufreq_free_table(freq_tables);
+ return ret;
+}
+module_init(armada_8k_cpufreq_init);
+
+static void __exit armada_8k_cpufreq_exit(void)
+{
+ struct freq_table *freq_tables = platform_get_drvdata(armada_8k_pdev);
+
+ armada_8k_cpufreq_free_table(freq_tables);
+ platform_device_unregister(armada_8k_pdev);
+}
+module_exit(armada_8k_cpufreq_exit);
+
+MODULE_AUTHOR("Gregory Clement <gregory.clement@bootlin.com>");
+MODULE_DESCRIPTION("Armada 8K cpufreq driver");
+MODULE_LICENSE("GPL");
--
2.20.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v5 2/2] cpufreq: ap806: add cpufreq driver for Armada 8K
@ 2019-01-18 14:11 ` Gregory CLEMENT
0 siblings, 0 replies; 10+ messages in thread
From: Gregory CLEMENT @ 2019-01-18 14:11 UTC (permalink / raw)
To: Rafael J. Wysocki, Viresh Kumar, linux-pm
Cc: Andrew Lunn, Jason Cooper, Antoine Tenart, Gregory CLEMENT,
Maxime Chevallier, Thomas Petazzoni, Miquèl Raynal,
linux-arm-kernel, Sebastian Hesselbarth
Add cpufreq driver for Marvell AP-806 found on Aramda 8K.
The AP-806 has DFS (Dynamic Frequency Scaling) with coupled
clock domain for two clusters, so this driver will directly
use generic cpufreq-dt driver as backend.
Based on the work of Omri Itach <omrii@marvell.com>.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
---
drivers/cpufreq/Kconfig.arm | 11 ++
drivers/cpufreq/Makefile | 1 +
drivers/cpufreq/armada-8k-cpufreq.c | 203 ++++++++++++++++++++++++++++
3 files changed, 215 insertions(+)
create mode 100644 drivers/cpufreq/armada-8k-cpufreq.c
diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
index 688f10227793..10bc5c798d17 100644
--- a/drivers/cpufreq/Kconfig.arm
+++ b/drivers/cpufreq/Kconfig.arm
@@ -25,6 +25,17 @@ config ARM_ARMADA_37XX_CPUFREQ
This adds the CPUFreq driver support for Marvell Armada 37xx SoCs.
The Armada 37xx PMU supports 4 frequency and VDD levels.
+config ARM_ARMADA_8K_CPUFREQ
+ tristate "Armada 8K CPUFreq driver"
+ depends on ARCH_MVEBU && CPUFREQ_DT
+ help
+ This enables the CPUFreq driver support for Marvell
+ Armada8k SOCs.
+ Armada8K device has the AP806 which supports scaling
+ to any full integer divider.
+
+ If in doubt, say N.
+
# big LITTLE core layer and glue drivers
config ARM_BIG_LITTLE_CPUFREQ
tristate "Generic ARM big LITTLE CPUfreq driver"
diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
index 08c071be2491..689b26c6f949 100644
--- a/drivers/cpufreq/Makefile
+++ b/drivers/cpufreq/Makefile
@@ -50,6 +50,7 @@ obj-$(CONFIG_X86_SFI_CPUFREQ) += sfi-cpufreq.o
obj-$(CONFIG_ARM_BIG_LITTLE_CPUFREQ) += arm_big_little.o
obj-$(CONFIG_ARM_ARMADA_37XX_CPUFREQ) += armada-37xx-cpufreq.o
+obj-$(CONFIG_ARM_ARMADA_8K_CPUFREQ) += armada-8k-cpufreq.o
obj-$(CONFIG_ARM_BRCMSTB_AVS_CPUFREQ) += brcmstb-avs-cpufreq.o
obj-$(CONFIG_ACPI_CPPC_CPUFREQ) += cppc_cpufreq.o
obj-$(CONFIG_ARCH_DAVINCI) += davinci-cpufreq.o
diff --git a/drivers/cpufreq/armada-8k-cpufreq.c b/drivers/cpufreq/armada-8k-cpufreq.c
new file mode 100644
index 000000000000..80375de4e149
--- /dev/null
+++ b/drivers/cpufreq/armada-8k-cpufreq.c
@@ -0,0 +1,203 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * CPUFreq support for Armada 8K
+ *
+ * Copyright (C) 2018 Marvell
+ *
+ * Omri Itach <omrii@marvell.com>
+ * Gregory Clement <gregory.clement@bootlin.com>
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/clk.h>
+#include <linux/cpu.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_opp.h>
+#include <linux/slab.h>
+
+/*
+ * Setup the opps list with the divider for the max frequency, that
+ * will be filled at runtime.
+ */
+static const int opps_div[] __initconst = {1, 2, 3, 4};
+
+static struct platform_device *armada_8k_pdev;
+
+struct freq_table {
+ struct device *cpu_dev;
+ unsigned int freq[ARRAY_SIZE(opps_div)];
+};
+
+/* If the CPUs share the same clock, then they are in the same cluster. */
+static void __init armada_8k_get_sharing_cpus(struct clk *cur_clk,
+ struct cpumask *cpumask)
+{
+ int cpu;
+
+ for_each_possible_cpu(cpu) {
+ struct device *cpu_dev;
+ struct clk *clk;
+
+ cpu_dev = get_cpu_device(cpu);
+ if (!cpu_dev) {
+ pr_warn("Failed to get cpu%d device\n", cpu);
+ continue;
+ }
+
+ clk = clk_get(cpu_dev, 0);
+ if (IS_ERR(clk))
+ pr_warn("Cannot get clock for CPU %d\n", cpu);
+ else if (clk_is_match(clk, cur_clk))
+ cpumask_set_cpu(cpu, cpumask);
+
+ if (!IS_ERR(clk))
+ clk_put(clk);
+ }
+}
+
+static int __init armada_8k_add_opp(struct clk *clk, struct device *cpu_dev,
+ struct freq_table *freq_tables,
+ int opps_index)
+{
+ unsigned int cur_frequency;
+ unsigned int freq;
+ int i, ret;
+
+ /* Get nominal (current) CPU frequency. */
+ cur_frequency = clk_get_rate(clk);
+ if (!cur_frequency) {
+ dev_err(cpu_dev, "Failed to get clock rate for this CPU\n");
+ return -EINVAL;
+ }
+
+ freq_tables[opps_index].cpu_dev = cpu_dev;
+
+ for (i = 0; i < ARRAY_SIZE(opps_div); i++) {
+ freq = cur_frequency / opps_div[i];
+
+ ret = dev_pm_opp_add(cpu_dev, freq, 0);
+ if (ret)
+ return ret;
+
+ freq_tables[opps_index].freq[i] = freq;
+ }
+
+ return 0;
+}
+
+static void armada_8k_cpufreq_free_table(struct freq_table *freq_tables)
+{
+ int opps_index, nb_cpus = num_possible_cpus();
+
+ for (opps_index = 0 ; opps_index <= nb_cpus; opps_index++) {
+ int i;
+
+ /* If cpu_dev is NULL then we reached the end of the array */
+ if (!freq_tables[opps_index].cpu_dev)
+ break;
+
+ for (i = 0; i < ARRAY_SIZE(opps_div); i++) {
+ /*
+ * A 0Hz frequency is not valid, this meant
+ * that it was not yet initialized so there is
+ * no more opp to free
+ */
+ if (freq_tables[opps_index].freq[i] == 0)
+ break;
+
+ dev_pm_opp_remove(freq_tables[opps_index].cpu_dev,
+ freq_tables[opps_index].freq[i]);
+ }
+ }
+
+ kfree(freq_tables);
+}
+
+static int __init armada_8k_cpufreq_init(void)
+{
+ int ret = 0, opps_index = 0, cpu, nb_cpus;
+ struct freq_table *freq_tables;
+ struct device_node *node;
+ struct cpumask cpus;
+
+ node = of_find_compatible_node(NULL, NULL, "marvell,ap806-cpu-clock");
+ if (!node || !of_device_is_available(node))
+ return -ENODEV;
+
+ nb_cpus = num_possible_cpus();
+ freq_tables = kcalloc(nb_cpus, sizeof(*freq_tables), GFP_KERNEL);
+ cpumask_copy(&cpus, cpu_possible_mask);
+
+ /*
+ * For each CPU, this loop registers the operating points
+ * supported (which are the nominal CPU frequency and full integer
+ * divisions of it).
+ */
+ for_each_cpu(cpu, &cpus) {
+ struct cpumask shared_cpus;
+ struct device *cpu_dev;
+ struct clk *clk;
+
+ cpu_dev = get_cpu_device(cpu);
+
+ if (!cpu_dev) {
+ pr_err("Cannot get CPU %d\n", cpu);
+ continue;
+ }
+
+ clk = clk_get(cpu_dev, 0);
+
+ if (IS_ERR(clk)) {
+ pr_err("Cannot get clock for CPU %d\n", cpu);
+ ret = PTR_ERR(clk);
+ goto remove_opp;
+ }
+
+ ret = armada_8k_add_opp(clk, cpu_dev, freq_tables, opps_index);
+ if (ret) {
+ clk_put(clk);
+ goto remove_opp;
+ }
+
+ opps_index++;
+ cpumask_clear(&shared_cpus);
+ armada_8k_get_sharing_cpus(clk, &shared_cpus);
+ dev_pm_opp_set_sharing_cpus(cpu_dev, &shared_cpus);
+ cpumask_andnot(&cpus, &cpus, &shared_cpus);
+ clk_put(clk);
+ }
+
+ armada_8k_pdev = platform_device_register_simple("cpufreq-dt", -1,
+ NULL, 0);
+ ret = PTR_ERR_OR_ZERO(armada_8k_pdev);
+ if (ret)
+ goto remove_opp;
+
+ platform_set_drvdata(armada_8k_pdev, freq_tables);
+
+ return 0;
+
+remove_opp:
+ armada_8k_cpufreq_free_table(freq_tables);
+ return ret;
+}
+module_init(armada_8k_cpufreq_init);
+
+static void __exit armada_8k_cpufreq_exit(void)
+{
+ struct freq_table *freq_tables = platform_get_drvdata(armada_8k_pdev);
+
+ armada_8k_cpufreq_free_table(freq_tables);
+ platform_device_unregister(armada_8k_pdev);
+}
+module_exit(armada_8k_cpufreq_exit);
+
+MODULE_AUTHOR("Gregory Clement <gregory.clement@bootlin.com>");
+MODULE_DESCRIPTION("Armada 8K cpufreq driver");
+MODULE_LICENSE("GPL");
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v5 2/2] cpufreq: ap806: add cpufreq driver for Armada 8K
2019-01-18 14:11 ` Gregory CLEMENT
@ 2019-01-18 14:51 ` Gregory CLEMENT
-1 siblings, 0 replies; 10+ messages in thread
From: Gregory CLEMENT @ 2019-01-18 14:51 UTC (permalink / raw)
To: Rafael J. Wysocki, Viresh Kumar, linux-pm
Cc: Andrew Lunn, Jason Cooper, Antoine Tenart, Gregory CLEMENT,
Maxime Chevallier, Thomas Petazzoni, Miquèl Raynal,
linux-arm-kernel, Sebastian Hesselbarth
Add cpufreq driver for Marvell AP-806 found on Aramda 8K.
The AP-806 has DFS (Dynamic Frequency Scaling) with coupled
clock domain for two clusters, so this driver will directly
use generic cpufreq-dt driver as backend.
Based on the work of Omri Itach <omrii@marvell.com>.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
---
Hi,
This one is the correct version, in the previous one the change were
not merged.
Sorry for the noise,
Gregory
drivers/cpufreq/Kconfig.arm | 11 ++
drivers/cpufreq/Makefile | 1 +
drivers/cpufreq/armada-8k-cpufreq.c | 204 ++++++++++++++++++++++++++++
3 files changed, 216 insertions(+)
create mode 100644 drivers/cpufreq/armada-8k-cpufreq.c
diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
index 688f10227793..10bc5c798d17 100644
--- a/drivers/cpufreq/Kconfig.arm
+++ b/drivers/cpufreq/Kconfig.arm
@@ -25,6 +25,17 @@ config ARM_ARMADA_37XX_CPUFREQ
This adds the CPUFreq driver support for Marvell Armada 37xx SoCs.
The Armada 37xx PMU supports 4 frequency and VDD levels.
+config ARM_ARMADA_8K_CPUFREQ
+ tristate "Armada 8K CPUFreq driver"
+ depends on ARCH_MVEBU && CPUFREQ_DT
+ help
+ This enables the CPUFreq driver support for Marvell
+ Armada8k SOCs.
+ Armada8K device has the AP806 which supports scaling
+ to any full integer divider.
+
+ If in doubt, say N.
+
# big LITTLE core layer and glue drivers
config ARM_BIG_LITTLE_CPUFREQ
tristate "Generic ARM big LITTLE CPUfreq driver"
diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
index 08c071be2491..689b26c6f949 100644
--- a/drivers/cpufreq/Makefile
+++ b/drivers/cpufreq/Makefile
@@ -50,6 +50,7 @@ obj-$(CONFIG_X86_SFI_CPUFREQ) += sfi-cpufreq.o
obj-$(CONFIG_ARM_BIG_LITTLE_CPUFREQ) += arm_big_little.o
obj-$(CONFIG_ARM_ARMADA_37XX_CPUFREQ) += armada-37xx-cpufreq.o
+obj-$(CONFIG_ARM_ARMADA_8K_CPUFREQ) += armada-8k-cpufreq.o
obj-$(CONFIG_ARM_BRCMSTB_AVS_CPUFREQ) += brcmstb-avs-cpufreq.o
obj-$(CONFIG_ACPI_CPPC_CPUFREQ) += cppc_cpufreq.o
obj-$(CONFIG_ARCH_DAVINCI) += davinci-cpufreq.o
diff --git a/drivers/cpufreq/armada-8k-cpufreq.c b/drivers/cpufreq/armada-8k-cpufreq.c
new file mode 100644
index 000000000000..8a5ddb93fc58
--- /dev/null
+++ b/drivers/cpufreq/armada-8k-cpufreq.c
@@ -0,0 +1,204 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * CPUFreq support for Armada 8K
+ *
+ * Copyright (C) 2018 Marvell
+ *
+ * Omri Itach <omrii@marvell.com>
+ * Gregory Clement <gregory.clement@bootlin.com>
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/clk.h>
+#include <linux/cpu.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_opp.h>
+#include <linux/slab.h>
+
+/*
+ * Setup the opps list with the divider for the max frequency, that
+ * will be filled at runtime.
+ */
+static const int opps_div[] __initconst = {1, 2, 3, 4};
+
+static struct platform_device *armada_8k_pdev;
+
+struct freq_table {
+ struct device *cpu_dev;
+ unsigned int freq[ARRAY_SIZE(opps_div)];
+};
+
+/* If the CPUs share the same clock, then they are in the same cluster. */
+static void __init armada_8k_get_sharing_cpus(struct clk *cur_clk,
+ struct cpumask *cpumask)
+{
+ int cpu;
+
+ for_each_possible_cpu(cpu) {
+ struct device *cpu_dev;
+ struct clk *clk;
+
+ cpu_dev = get_cpu_device(cpu);
+ if (!cpu_dev) {
+ pr_warn("Failed to get cpu%d device\n", cpu);
+ continue;
+ }
+
+ clk = clk_get(cpu_dev, 0);
+ if (IS_ERR(clk)) {
+ pr_warn("Cannot get clock for CPU %d\n", cpu);
+ } else {
+ if (clk_is_match(clk, cur_clk))
+ cpumask_set_cpu(cpu, cpumask);
+
+ clk_put(clk);
+ }
+ }
+}
+
+static int __init armada_8k_add_opp(struct clk *clk, struct device *cpu_dev,
+ struct freq_table *freq_tables,
+ int opps_index)
+{
+ unsigned int cur_frequency;
+ unsigned int freq;
+ int i, ret;
+
+ /* Get nominal (current) CPU frequency. */
+ cur_frequency = clk_get_rate(clk);
+ if (!cur_frequency) {
+ dev_err(cpu_dev, "Failed to get clock rate for this CPU\n");
+ return -EINVAL;
+ }
+
+ freq_tables[opps_index].cpu_dev = cpu_dev;
+
+ for (i = 0; i < ARRAY_SIZE(opps_div); i++) {
+ freq = cur_frequency / opps_div[i];
+
+ ret = dev_pm_opp_add(cpu_dev, freq, 0);
+ if (ret)
+ return ret;
+
+ freq_tables[opps_index].freq[i] = freq;
+ }
+
+ return 0;
+}
+
+static void armada_8k_cpufreq_free_table(struct freq_table *freq_tables)
+{
+ int opps_index, nb_cpus = num_possible_cpus();
+
+ for (opps_index = 0 ; opps_index <= nb_cpus; opps_index++) {
+ int i;
+
+ /* If cpu_dev is NULL then we reached the end of the array */
+ if (!freq_tables[opps_index].cpu_dev)
+ break;
+
+ for (i = 0; i < ARRAY_SIZE(opps_div); i++) {
+ /*
+ * A 0Hz frequency is not valid, this meant
+ * that it was not yet initialized so there is
+ * no more opp to free
+ */
+ if (freq_tables[opps_index].freq[i] == 0)
+ break;
+
+ dev_pm_opp_remove(freq_tables[opps_index].cpu_dev,
+ freq_tables[opps_index].freq[i]);
+ }
+ }
+
+ kfree(freq_tables);
+}
+
+static int __init armada_8k_cpufreq_init(void)
+{
+ int ret = 0, opps_index = 0, cpu, nb_cpus;
+ struct freq_table *freq_tables;
+ struct device_node *node;
+ struct cpumask cpus;
+
+ node = of_find_compatible_node(NULL, NULL, "marvell,ap806-cpu-clock");
+ if (!node || !of_device_is_available(node))
+ return -ENODEV;
+
+ nb_cpus = num_possible_cpus();
+ freq_tables = kcalloc(nb_cpus, sizeof(*freq_tables), GFP_KERNEL);
+ cpumask_copy(&cpus, cpu_possible_mask);
+
+ /*
+ * For each CPU, this loop registers the operating points
+ * supported (which are the nominal CPU frequency and full integer
+ * divisions of it).
+ */
+ for_each_cpu(cpu, &cpus) {
+ struct cpumask shared_cpus;
+ struct device *cpu_dev;
+ struct clk *clk;
+
+ cpu_dev = get_cpu_device(cpu);
+
+ if (!cpu_dev) {
+ pr_err("Cannot get CPU %d\n", cpu);
+ continue;
+ }
+
+ clk = clk_get(cpu_dev, 0);
+
+ if (IS_ERR(clk)) {
+ pr_err("Cannot get clock for CPU %d\n", cpu);
+ ret = PTR_ERR(clk);
+ goto remove_opp;
+ }
+
+ ret = armada_8k_add_opp(clk, cpu_dev, freq_tables, opps_index);
+ if (ret) {
+ clk_put(clk);
+ goto remove_opp;
+ }
+
+ opps_index++;
+ cpumask_clear(&shared_cpus);
+ armada_8k_get_sharing_cpus(clk, &shared_cpus);
+ dev_pm_opp_set_sharing_cpus(cpu_dev, &shared_cpus);
+ cpumask_andnot(&cpus, &cpus, &shared_cpus);
+ clk_put(clk);
+ }
+
+ armada_8k_pdev = platform_device_register_simple("cpufreq-dt", -1,
+ NULL, 0);
+ ret = PTR_ERR_OR_ZERO(armada_8k_pdev);
+ if (ret)
+ goto remove_opp;
+
+ platform_set_drvdata(armada_8k_pdev, freq_tables);
+
+ return 0;
+
+remove_opp:
+ armada_8k_cpufreq_free_table(freq_tables);
+ return ret;
+}
+module_init(armada_8k_cpufreq_init);
+
+static void __exit armada_8k_cpufreq_exit(void)
+{
+ struct freq_table *freq_tables = platform_get_drvdata(armada_8k_pdev);
+
+ platform_device_unregister(armada_8k_pdev);
+ armada_8k_cpufreq_free_table(freq_tables);
+}
+module_exit(armada_8k_cpufreq_exit);
+
+MODULE_AUTHOR("Gregory Clement <gregory.clement@bootlin.com>");
+MODULE_DESCRIPTION("Armada 8K cpufreq driver");
+MODULE_LICENSE("GPL");
--
2.20.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v5 2/2] cpufreq: ap806: add cpufreq driver for Armada 8K
@ 2019-01-18 14:51 ` Gregory CLEMENT
0 siblings, 0 replies; 10+ messages in thread
From: Gregory CLEMENT @ 2019-01-18 14:51 UTC (permalink / raw)
To: Rafael J. Wysocki, Viresh Kumar, linux-pm
Cc: Andrew Lunn, Jason Cooper, Antoine Tenart, Gregory CLEMENT,
Maxime Chevallier, Thomas Petazzoni, Miquèl Raynal,
linux-arm-kernel, Sebastian Hesselbarth
Add cpufreq driver for Marvell AP-806 found on Aramda 8K.
The AP-806 has DFS (Dynamic Frequency Scaling) with coupled
clock domain for two clusters, so this driver will directly
use generic cpufreq-dt driver as backend.
Based on the work of Omri Itach <omrii@marvell.com>.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
---
Hi,
This one is the correct version, in the previous one the change were
not merged.
Sorry for the noise,
Gregory
drivers/cpufreq/Kconfig.arm | 11 ++
drivers/cpufreq/Makefile | 1 +
drivers/cpufreq/armada-8k-cpufreq.c | 204 ++++++++++++++++++++++++++++
3 files changed, 216 insertions(+)
create mode 100644 drivers/cpufreq/armada-8k-cpufreq.c
diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
index 688f10227793..10bc5c798d17 100644
--- a/drivers/cpufreq/Kconfig.arm
+++ b/drivers/cpufreq/Kconfig.arm
@@ -25,6 +25,17 @@ config ARM_ARMADA_37XX_CPUFREQ
This adds the CPUFreq driver support for Marvell Armada 37xx SoCs.
The Armada 37xx PMU supports 4 frequency and VDD levels.
+config ARM_ARMADA_8K_CPUFREQ
+ tristate "Armada 8K CPUFreq driver"
+ depends on ARCH_MVEBU && CPUFREQ_DT
+ help
+ This enables the CPUFreq driver support for Marvell
+ Armada8k SOCs.
+ Armada8K device has the AP806 which supports scaling
+ to any full integer divider.
+
+ If in doubt, say N.
+
# big LITTLE core layer and glue drivers
config ARM_BIG_LITTLE_CPUFREQ
tristate "Generic ARM big LITTLE CPUfreq driver"
diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
index 08c071be2491..689b26c6f949 100644
--- a/drivers/cpufreq/Makefile
+++ b/drivers/cpufreq/Makefile
@@ -50,6 +50,7 @@ obj-$(CONFIG_X86_SFI_CPUFREQ) += sfi-cpufreq.o
obj-$(CONFIG_ARM_BIG_LITTLE_CPUFREQ) += arm_big_little.o
obj-$(CONFIG_ARM_ARMADA_37XX_CPUFREQ) += armada-37xx-cpufreq.o
+obj-$(CONFIG_ARM_ARMADA_8K_CPUFREQ) += armada-8k-cpufreq.o
obj-$(CONFIG_ARM_BRCMSTB_AVS_CPUFREQ) += brcmstb-avs-cpufreq.o
obj-$(CONFIG_ACPI_CPPC_CPUFREQ) += cppc_cpufreq.o
obj-$(CONFIG_ARCH_DAVINCI) += davinci-cpufreq.o
diff --git a/drivers/cpufreq/armada-8k-cpufreq.c b/drivers/cpufreq/armada-8k-cpufreq.c
new file mode 100644
index 000000000000..8a5ddb93fc58
--- /dev/null
+++ b/drivers/cpufreq/armada-8k-cpufreq.c
@@ -0,0 +1,204 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * CPUFreq support for Armada 8K
+ *
+ * Copyright (C) 2018 Marvell
+ *
+ * Omri Itach <omrii@marvell.com>
+ * Gregory Clement <gregory.clement@bootlin.com>
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/clk.h>
+#include <linux/cpu.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_opp.h>
+#include <linux/slab.h>
+
+/*
+ * Setup the opps list with the divider for the max frequency, that
+ * will be filled at runtime.
+ */
+static const int opps_div[] __initconst = {1, 2, 3, 4};
+
+static struct platform_device *armada_8k_pdev;
+
+struct freq_table {
+ struct device *cpu_dev;
+ unsigned int freq[ARRAY_SIZE(opps_div)];
+};
+
+/* If the CPUs share the same clock, then they are in the same cluster. */
+static void __init armada_8k_get_sharing_cpus(struct clk *cur_clk,
+ struct cpumask *cpumask)
+{
+ int cpu;
+
+ for_each_possible_cpu(cpu) {
+ struct device *cpu_dev;
+ struct clk *clk;
+
+ cpu_dev = get_cpu_device(cpu);
+ if (!cpu_dev) {
+ pr_warn("Failed to get cpu%d device\n", cpu);
+ continue;
+ }
+
+ clk = clk_get(cpu_dev, 0);
+ if (IS_ERR(clk)) {
+ pr_warn("Cannot get clock for CPU %d\n", cpu);
+ } else {
+ if (clk_is_match(clk, cur_clk))
+ cpumask_set_cpu(cpu, cpumask);
+
+ clk_put(clk);
+ }
+ }
+}
+
+static int __init armada_8k_add_opp(struct clk *clk, struct device *cpu_dev,
+ struct freq_table *freq_tables,
+ int opps_index)
+{
+ unsigned int cur_frequency;
+ unsigned int freq;
+ int i, ret;
+
+ /* Get nominal (current) CPU frequency. */
+ cur_frequency = clk_get_rate(clk);
+ if (!cur_frequency) {
+ dev_err(cpu_dev, "Failed to get clock rate for this CPU\n");
+ return -EINVAL;
+ }
+
+ freq_tables[opps_index].cpu_dev = cpu_dev;
+
+ for (i = 0; i < ARRAY_SIZE(opps_div); i++) {
+ freq = cur_frequency / opps_div[i];
+
+ ret = dev_pm_opp_add(cpu_dev, freq, 0);
+ if (ret)
+ return ret;
+
+ freq_tables[opps_index].freq[i] = freq;
+ }
+
+ return 0;
+}
+
+static void armada_8k_cpufreq_free_table(struct freq_table *freq_tables)
+{
+ int opps_index, nb_cpus = num_possible_cpus();
+
+ for (opps_index = 0 ; opps_index <= nb_cpus; opps_index++) {
+ int i;
+
+ /* If cpu_dev is NULL then we reached the end of the array */
+ if (!freq_tables[opps_index].cpu_dev)
+ break;
+
+ for (i = 0; i < ARRAY_SIZE(opps_div); i++) {
+ /*
+ * A 0Hz frequency is not valid, this meant
+ * that it was not yet initialized so there is
+ * no more opp to free
+ */
+ if (freq_tables[opps_index].freq[i] == 0)
+ break;
+
+ dev_pm_opp_remove(freq_tables[opps_index].cpu_dev,
+ freq_tables[opps_index].freq[i]);
+ }
+ }
+
+ kfree(freq_tables);
+}
+
+static int __init armada_8k_cpufreq_init(void)
+{
+ int ret = 0, opps_index = 0, cpu, nb_cpus;
+ struct freq_table *freq_tables;
+ struct device_node *node;
+ struct cpumask cpus;
+
+ node = of_find_compatible_node(NULL, NULL, "marvell,ap806-cpu-clock");
+ if (!node || !of_device_is_available(node))
+ return -ENODEV;
+
+ nb_cpus = num_possible_cpus();
+ freq_tables = kcalloc(nb_cpus, sizeof(*freq_tables), GFP_KERNEL);
+ cpumask_copy(&cpus, cpu_possible_mask);
+
+ /*
+ * For each CPU, this loop registers the operating points
+ * supported (which are the nominal CPU frequency and full integer
+ * divisions of it).
+ */
+ for_each_cpu(cpu, &cpus) {
+ struct cpumask shared_cpus;
+ struct device *cpu_dev;
+ struct clk *clk;
+
+ cpu_dev = get_cpu_device(cpu);
+
+ if (!cpu_dev) {
+ pr_err("Cannot get CPU %d\n", cpu);
+ continue;
+ }
+
+ clk = clk_get(cpu_dev, 0);
+
+ if (IS_ERR(clk)) {
+ pr_err("Cannot get clock for CPU %d\n", cpu);
+ ret = PTR_ERR(clk);
+ goto remove_opp;
+ }
+
+ ret = armada_8k_add_opp(clk, cpu_dev, freq_tables, opps_index);
+ if (ret) {
+ clk_put(clk);
+ goto remove_opp;
+ }
+
+ opps_index++;
+ cpumask_clear(&shared_cpus);
+ armada_8k_get_sharing_cpus(clk, &shared_cpus);
+ dev_pm_opp_set_sharing_cpus(cpu_dev, &shared_cpus);
+ cpumask_andnot(&cpus, &cpus, &shared_cpus);
+ clk_put(clk);
+ }
+
+ armada_8k_pdev = platform_device_register_simple("cpufreq-dt", -1,
+ NULL, 0);
+ ret = PTR_ERR_OR_ZERO(armada_8k_pdev);
+ if (ret)
+ goto remove_opp;
+
+ platform_set_drvdata(armada_8k_pdev, freq_tables);
+
+ return 0;
+
+remove_opp:
+ armada_8k_cpufreq_free_table(freq_tables);
+ return ret;
+}
+module_init(armada_8k_cpufreq_init);
+
+static void __exit armada_8k_cpufreq_exit(void)
+{
+ struct freq_table *freq_tables = platform_get_drvdata(armada_8k_pdev);
+
+ platform_device_unregister(armada_8k_pdev);
+ armada_8k_cpufreq_free_table(freq_tables);
+}
+module_exit(armada_8k_cpufreq_exit);
+
+MODULE_AUTHOR("Gregory Clement <gregory.clement@bootlin.com>");
+MODULE_DESCRIPTION("Armada 8K cpufreq driver");
+MODULE_LICENSE("GPL");
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH v5 0/2] Add cpufreq support for Armada 8K
2019-01-18 14:11 ` Gregory CLEMENT
@ 2019-01-23 10:08 ` Viresh Kumar
-1 siblings, 0 replies; 10+ messages in thread
From: Viresh Kumar @ 2019-01-23 10:08 UTC (permalink / raw)
To: Gregory CLEMENT
Cc: Andrew Lunn, Jason Cooper, linux-pm, Antoine Tenart,
Rafael J. Wysocki, Maxime Chevallier, Thomas Petazzoni,
Miquèl Raynal, linux-arm-kernel, Sebastian Hesselbarth
On 18-01-19, 15:11, Gregory CLEMENT wrote:
> Hi,
>
> this is the fifth version of a the series adding the cpufreq support
> for the Marvell Armada 8K SoCs.
Applied. Thanks.
--
viresh
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v5 0/2] Add cpufreq support for Armada 8K
@ 2019-01-23 10:08 ` Viresh Kumar
0 siblings, 0 replies; 10+ messages in thread
From: Viresh Kumar @ 2019-01-23 10:08 UTC (permalink / raw)
To: Gregory CLEMENT
Cc: Andrew Lunn, Jason Cooper, linux-pm, Antoine Tenart,
Rafael J. Wysocki, Maxime Chevallier, Thomas Petazzoni,
Miquèl Raynal, linux-arm-kernel, Sebastian Hesselbarth
On 18-01-19, 15:11, Gregory CLEMENT wrote:
> Hi,
>
> this is the fifth version of a the series adding the cpufreq support
> for the Marvell Armada 8K SoCs.
Applied. Thanks.
--
viresh
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2019-01-23 10:08 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-01-18 14:11 [PATCH v5 0/2] Add cpufreq support for Armada 8K Gregory CLEMENT
2019-01-18 14:11 ` Gregory CLEMENT
2019-01-18 14:11 ` [PATCH v5 1/2] MAINTAINERS: add new entries for Armada 8K cpufreq driver Gregory CLEMENT
2019-01-18 14:11 ` Gregory CLEMENT
2019-01-18 14:11 ` [PATCH v5 2/2] cpufreq: ap806: add cpufreq driver for Armada 8K Gregory CLEMENT
2019-01-18 14:11 ` Gregory CLEMENT
2019-01-18 14:51 ` Gregory CLEMENT
2019-01-18 14:51 ` Gregory CLEMENT
2019-01-23 10:08 ` [PATCH v5 0/2] Add cpufreq support " Viresh Kumar
2019-01-23 10:08 ` Viresh Kumar
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.