* [U-Boot] [PATCH v2 0/4] Add Support for NAND in dra71x-evm
@ 2019-02-27 7:59 Faiz Abbas
2019-02-27 7:59 ` [U-Boot] [PATCH v2 1/4] board: ti: dra71: Add pinmux settings for NAND on DRA71x EVM Faiz Abbas
` (4 more replies)
0 siblings, 5 replies; 12+ messages in thread
From: Faiz Abbas @ 2019-02-27 7:59 UTC (permalink / raw)
To: u-boot
The following patches add support for NAND and booting from
NAND in dra71x-evm.
v2:
Patch4: Moved NANDARGS to its own file in include/environment/ti
Faiz Abbas (2):
configs: dra71x-evm: Add Support for NAND
configs: ti_omap5_common: Add NAND environment settings
Franklin S Cooper Jr (2):
board: ti: dra71: Add pinmux settings for NAND on DRA71x EVM
arm: dra7: Allow NAND to be enabled on DRA71x EVM.
board/ti/dra7xx/evm.c | 56 +++++++++++++++++++++++++++++
board/ti/dra7xx/mux_data.h | 60 ++++++++++++++++++++++---------
configs/dra7xx_evm_defconfig | 7 +++-
configs/dra7xx_hs_evm_defconfig | 7 +++-
include/configs/dra7xx_evm.h | 2 +-
include/configs/ti_omap5_common.h | 3 +-
include/environment/ti/nand.h | 26 ++++++++++++++
7 files changed, 141 insertions(+), 20 deletions(-)
create mode 100644 include/environment/ti/nand.h
--
2.19.2
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH v2 1/4] board: ti: dra71: Add pinmux settings for NAND on DRA71x EVM
2019-02-27 7:59 [U-Boot] [PATCH v2 0/4] Add Support for NAND in dra71x-evm Faiz Abbas
@ 2019-02-27 7:59 ` Faiz Abbas
2019-04-12 16:30 ` [U-Boot] [U-Boot, v2, " Tom Rini
2019-02-27 7:59 ` [U-Boot] [PATCH v2 2/4] arm: dra7: Allow NAND to be enabled " Faiz Abbas
` (3 subsequent siblings)
4 siblings, 1 reply; 12+ messages in thread
From: Faiz Abbas @ 2019-02-27 7:59 UTC (permalink / raw)
To: u-boot
From: Franklin S Cooper Jr <fcooper@ti.com>
By default VOUT3 occupies the pins required for NAND. Therefore, create
a seperate entry that can be use to reconfigure these pins to work for
NAND.
On the EVM SWITCH 8 pins 0 and 1 will be used to determine if NAND is
enabled or not. For NAND to be selected pin 0 should be on and pin 1
should be off. Any other combination will assume NAND shouldn't be
enabled.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
---
board/ti/dra7xx/mux_data.h | 60 ++++++++++++++++++++++++++++----------
1 file changed, 44 insertions(+), 16 deletions(-)
diff --git a/board/ti/dra7xx/mux_data.h b/board/ti/dra7xx/mux_data.h
index f1f6bd5316..75da5cb608 100644
--- a/board/ti/dra7xx/mux_data.h
+++ b/board/ti/dra7xx/mux_data.h
@@ -220,22 +220,6 @@ const struct pad_conf_entry dra72x_rgmii_padconf_array_revc[] = {
};
const struct pad_conf_entry dra71x_core_padconf_array[] = {
- {GPMC_AD0, (M3 | PIN_INPUT)}, /* gpmc_ad0.vout3_d0 */
- {GPMC_AD1, (M3 | PIN_INPUT)}, /* gpmc_ad1.vout3_d1 */
- {GPMC_AD2, (M3 | PIN_INPUT)}, /* gpmc_ad2.vout3_d2 */
- {GPMC_AD3, (M3 | PIN_INPUT)}, /* gpmc_ad3.vout3_d3 */
- {GPMC_AD4, (M3 | PIN_INPUT)}, /* gpmc_ad4.vout3_d4 */
- {GPMC_AD5, (M3 | PIN_INPUT)}, /* gpmc_ad5.vout3_d5 */
- {GPMC_AD6, (M3 | PIN_INPUT)}, /* gpmc_ad6.vout3_d6 */
- {GPMC_AD7, (M3 | PIN_INPUT)}, /* gpmc_ad7.vout3_d7 */
- {GPMC_AD8, (M3 | PIN_INPUT)}, /* gpmc_ad8.vout3_d8 */
- {GPMC_AD9, (M3 | PIN_INPUT)}, /* gpmc_ad9.vout3_d9 */
- {GPMC_AD10, (M3 | PIN_INPUT)}, /* gpmc_ad10.vout3_d10 */
- {GPMC_AD11, (M3 | PIN_INPUT)}, /* gpmc_ad11.vout3_d11 */
- {GPMC_AD12, (M3 | PIN_INPUT)}, /* gpmc_ad12.vout3_d12 */
- {GPMC_AD13, (M3 | PIN_INPUT)}, /* gpmc_ad13.vout3_d13 */
- {GPMC_AD14, (M3 | PIN_INPUT)}, /* gpmc_ad14.vout3_d14 */
- {GPMC_AD15, (M3 | PIN_INPUT)}, /* gpmc_ad15.vout3_d15 */
{GPMC_A0, (M3 | PIN_INPUT_PULLDOWN)}, /* gpmc_a0.vout3_d16 */
{GPMC_A1, (M3 | PIN_INPUT_PULLDOWN)}, /* gpmc_a1.vout3_d17 */
{GPMC_A2, (M3 | PIN_INPUT_PULLDOWN)}, /* gpmc_a2.vout3_d18 */
@@ -370,6 +354,50 @@ const struct pad_conf_entry dra71x_core_padconf_array[] = {
{WAKEUP3, (M1 | PULL_ENA | PULL_UP)}, /* Wakeup3.sys_nirq1 */
};
+const struct pad_conf_entry dra71x_vout3_padconf_array[] = {
+ {GPMC_AD0, (M3 | PIN_INPUT)}, /* gpmc_ad0.vout3_d0 */
+ {GPMC_AD1, (M3 | PIN_INPUT)}, /* gpmc_ad1.vout3_d1 */
+ {GPMC_AD2, (M3 | PIN_INPUT)}, /* gpmc_ad2.vout3_d2 */
+ {GPMC_AD3, (M3 | PIN_INPUT)}, /* gpmc_ad3.vout3_d3 */
+ {GPMC_AD4, (M3 | PIN_INPUT)}, /* gpmc_ad4.vout3_d4 */
+ {GPMC_AD5, (M3 | PIN_INPUT)}, /* gpmc_ad5.vout3_d5 */
+ {GPMC_AD6, (M3 | PIN_INPUT)}, /* gpmc_ad6.vout3_d6 */
+ {GPMC_AD7, (M3 | PIN_INPUT)}, /* gpmc_ad7.vout3_d7 */
+ {GPMC_AD8, (M3 | PIN_INPUT)}, /* gpmc_ad8.vout3_d8 */
+ {GPMC_AD9, (M3 | PIN_INPUT)}, /* gpmc_ad9.vout3_d9 */
+ {GPMC_AD10, (M3 | PIN_INPUT)}, /* gpmc_ad10.vout3_d10 */
+ {GPMC_AD11, (M3 | PIN_INPUT)}, /* gpmc_ad11.vout3_d11 */
+ {GPMC_AD12, (M3 | PIN_INPUT)}, /* gpmc_ad12.vout3_d12 */
+ {GPMC_AD13, (M3 | PIN_INPUT)}, /* gpmc_ad13.vout3_d13 */
+ {GPMC_AD14, (M3 | PIN_INPUT)}, /* gpmc_ad14.vout3_d14 */
+ {GPMC_AD15, (M3 | PIN_INPUT)}, /* gpmc_ad15.vout3_d15 */
+};
+
+const struct pad_conf_entry dra71x_nand_padconf_array[] = {
+ {GPMC_AD0, (M0 | PIN_INPUT)}, /* gpmc_ad0.gpmc_ad0 */
+ {GPMC_AD1, (M0 | PIN_INPUT)}, /* gpmc_ad1.gpmc_ad1 */
+ {GPMC_AD2, (M0 | PIN_INPUT)}, /* gpmc_ad2.gpmc_ad2 */
+ {GPMC_AD3, (M0 | PIN_INPUT)}, /* gpmc_ad3.gpmc_ad3 */
+ {GPMC_AD4, (M0 | PIN_INPUT)}, /* gpmc_ad4.gpmc_ad4 */
+ {GPMC_AD5, (M0 | PIN_INPUT)}, /* gpmc_ad5.gpmc_ad5 */
+ {GPMC_AD6, (M0 | PIN_INPUT)}, /* gpmc_ad6.gpmc_ad6 */
+ {GPMC_AD7, (M0 | PIN_INPUT)}, /* gpmc_ad7.gpmc_ad7 */
+ {GPMC_AD8, (M0 | PIN_INPUT)}, /* gpmc_ad8.gpmc_ad8 */
+ {GPMC_AD9, (M0 | PIN_INPUT)}, /* gpmc_ad9.gpmc_ad9 */
+ {GPMC_AD10, (M0 | PIN_INPUT)}, /* gpmc_ad10.gpmc_ad10 */
+ {GPMC_AD11, (M0 | PIN_INPUT)}, /* gpmc_ad11.gpmc_ad11 */
+ {GPMC_AD12, (M0 | PIN_INPUT)}, /* gpmc_ad12.gpmc_ad12 */
+ {GPMC_AD13, (M0 | PIN_INPUT)}, /* gpmc_ad13.gpmc_ad13 */
+ {GPMC_AD14, (M0 | PIN_INPUT)}, /* gpmc_ad14.gpmc_ad14 */
+ {GPMC_AD15, (M0 | PIN_INPUT)}, /* gpmc_ad15.gpmc_ad15 */
+ {GPMC_CS0, (M0 | PIN_INPUT_PULLUP)}, /* gpmc_cs0.gpmc_cs0 */
+ {GPMC_ADVN_ALE, (M0 | PIN_INPUT_PULLDOWN)}, /* gpmc_advn_ale.gpmc_advn_ale */
+ {GPMC_OEN_REN, (M0 | PIN_INPUT_PULLUP)}, /* gpmc_oen_ren.gpmc_oen_ren */
+ {GPMC_WEN, (M0 | PIN_INPUT_PULLUP)}, /* gpmc_wen.gpmc_wen */
+ {GPMC_BEN0, (M0 | PIN_INPUT_PULLDOWN)}, /* gpmc_ben0.gpmc_ben0 */
+ {GPMC_WAIT0, (M0 | PIN_INPUT_PULLUP | SLEWCONTROL)}, /* gpmc_wait0.gpmc_wait0 */
+};
+
const struct pad_conf_entry early_padconf[] = {
{UART1_RXD, (PIN_INPUT_SLEW | M0)}, /* UART1_RXD */
{UART1_TXD, (PIN_INPUT_SLEW | M0)}, /* UART1_TXD */
--
2.19.2
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH v2 2/4] arm: dra7: Allow NAND to be enabled on DRA71x EVM.
2019-02-27 7:59 [U-Boot] [PATCH v2 0/4] Add Support for NAND in dra71x-evm Faiz Abbas
2019-02-27 7:59 ` [U-Boot] [PATCH v2 1/4] board: ti: dra71: Add pinmux settings for NAND on DRA71x EVM Faiz Abbas
@ 2019-02-27 7:59 ` Faiz Abbas
2019-04-12 16:30 ` [U-Boot] [U-Boot, v2, " Tom Rini
2019-02-27 7:59 ` [U-Boot] [PATCH v2 3/4] configs: dra71x-evm: Add Support for NAND Faiz Abbas
` (2 subsequent siblings)
4 siblings, 1 reply; 12+ messages in thread
From: Faiz Abbas @ 2019-02-27 7:59 UTC (permalink / raw)
To: u-boot
From: Franklin S Cooper Jr <fcooper@ti.com>
If SW 8 pins 0 and 1 indicate that NAND should be enabled then
the pins pinmux must be reconfigured for NAND mode.
Therefore, enable NAND by reconfiguring the pinmux.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
---
board/ti/dra7xx/evm.c | 56 +++++++++++++++++++++++++++++++++++++++++++
1 file changed, 56 insertions(+)
diff --git a/board/ti/dra7xx/evm.c b/board/ti/dra7xx/evm.c
index d69641e3a0..446ce8399c 100644
--- a/board/ti/dra7xx/evm.c
+++ b/board/ti/dra7xx/evm.c
@@ -27,6 +27,7 @@
#include <environment.h>
#include <dwc3-uboot.h>
#include <dwc3-omap-uboot.h>
+#include <i2c.h>
#include <ti-usb-phy-uboot.h>
#include <miiphy.h>
@@ -55,6 +56,10 @@ DECLARE_GLOBAL_DATA_PTR;
#define SYSINFO_BOARD_NAME_MAX_LEN 37
+/* I2C I/O Expander */
+#define NAND_PCF8575_ADDR 0x21
+#define NAND_PCF8575_I2C_BUS_NUM 0
+
const struct omap_sysinfo sysinfo = {
"Board: UNKNOWN(DRA7 EVM) REV UNKNOWN\n"
};
@@ -777,6 +782,44 @@ void set_muxconf_regs(void)
early_padconf, ARRAY_SIZE(early_padconf));
}
+#if defined(CONFIG_NAND)
+static int nand_sw_detect(void)
+{
+ int rc;
+ uchar data[2];
+ struct udevice *dev;
+
+ rc = i2c_get_chip_for_busnum(NAND_PCF8575_I2C_BUS_NUM,
+ NAND_PCF8575_ADDR, 0, &dev);
+ if (rc)
+ return -1;
+
+ rc = dm_i2c_read(dev, 0, (uint8_t *)&data, sizeof(data));
+ if (rc)
+ return -1;
+
+ /* We are only interested in P10 and P11 on PCF8575 which is equal to
+ * bits 8 and 9.
+ */
+ data[1] = data[1] & 0x3;
+
+ /* Ensure only P11 is set and P10 is cleared. This ensures only
+ * NAND (P10) is configured and not NOR (P11) which are both low
+ * true signals. NAND and NOR settings should not be enabled at
+ * the same time.
+ */
+ if (data[1] == 0x2)
+ return 0;
+
+ return -1;
+}
+#else
+int nand_sw_detect(void)
+{
+ return -1;
+}
+#endif
+
#ifdef CONFIG_IODELAY_RECALIBRATION
void recalibrate_iodelay(void)
{
@@ -796,6 +839,19 @@ void recalibrate_iodelay(void)
npads = ARRAY_SIZE(dra71x_core_padconf_array);
iodelay = dra71_iodelay_cfg_array;
niodelays = ARRAY_SIZE(dra71_iodelay_cfg_array);
+ /* If SW8 on the EVM is set to enable NAND then
+ * overwrite the pins used by VOUT3 with NAND.
+ */
+ if (!nand_sw_detect()) {
+ delta_pads = dra71x_nand_padconf_array;
+ delta_npads =
+ ARRAY_SIZE(dra71x_nand_padconf_array);
+ } else {
+ delta_pads = dra71x_vout3_padconf_array;
+ delta_npads =
+ ARRAY_SIZE(dra71x_vout3_padconf_array);
+ }
+
} else if (board_is_dra72x_revc_or_later()) {
delta_pads = dra72x_rgmii_padconf_array_revc;
delta_npads =
--
2.19.2
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH v2 3/4] configs: dra71x-evm: Add Support for NAND
2019-02-27 7:59 [U-Boot] [PATCH v2 0/4] Add Support for NAND in dra71x-evm Faiz Abbas
2019-02-27 7:59 ` [U-Boot] [PATCH v2 1/4] board: ti: dra71: Add pinmux settings for NAND on DRA71x EVM Faiz Abbas
2019-02-27 7:59 ` [U-Boot] [PATCH v2 2/4] arm: dra7: Allow NAND to be enabled " Faiz Abbas
@ 2019-02-27 7:59 ` Faiz Abbas
2019-04-12 16:30 ` [U-Boot] [U-Boot, v2, " Tom Rini
2019-02-27 7:59 ` [U-Boot] [PATCH v2 4/4] configs: ti_omap5_common: Add NAND environment settings Faiz Abbas
2019-03-13 15:05 ` [U-Boot] [PATCH v2 0/4] Add Support for NAND in dra71x-evm Faiz Abbas
4 siblings, 1 reply; 12+ messages in thread
From: Faiz Abbas @ 2019-02-27 7:59 UTC (permalink / raw)
To: u-boot
Add NAND support to dra71x-evm defconfig
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
---
configs/dra7xx_evm_defconfig | 3 +++
configs/dra7xx_hs_evm_defconfig | 3 +++
2 files changed, 6 insertions(+)
diff --git a/configs/dra7xx_evm_defconfig b/configs/dra7xx_evm_defconfig
index 3f25a2ec28..d71d989c4c 100644
--- a/configs/dra7xx_evm_defconfig
+++ b/configs/dra7xx_evm_defconfig
@@ -28,6 +28,7 @@ CONFIG_SPL_OS_BOOT=y
CONFIG_SPL_SPI_LOAD=y
CONFIG_CMD_SPL=y
# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_NAND=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_OF_CONTROL=y
CONFIG_SPL_OF_CONTROL=y
@@ -66,6 +67,8 @@ CONFIG_MMC_UHS_SUPPORT=y
CONFIG_MMC_HS200_SUPPORT=y
CONFIG_SPL_MMC_HS200_SUPPORT=y
CONFIG_MMC_OMAP_HS=y
+CONFIG_NAND=y
+CONFIG_SYS_NAND_BUSWIDTH_16BIT=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_SPANSION=y
diff --git a/configs/dra7xx_hs_evm_defconfig b/configs/dra7xx_hs_evm_defconfig
index ee28e0c6ec..4642da3c01 100644
--- a/configs/dra7xx_hs_evm_defconfig
+++ b/configs/dra7xx_hs_evm_defconfig
@@ -32,6 +32,7 @@ CONFIG_SPL_DMA_SUPPORT=y
# CONFIG_SPL_NAND_SUPPORT is not set
CONFIG_SPL_SPI_LOAD=y
# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_NAND=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_OF_CONTROL=y
CONFIG_SPL_OF_CONTROL=y
@@ -70,6 +71,8 @@ CONFIG_MMC_UHS_SUPPORT=y
CONFIG_MMC_HS200_SUPPORT=y
CONFIG_SPL_MMC_HS200_SUPPORT=y
CONFIG_MMC_OMAP_HS=y
+CONFIG_NAND=y
+CONFIG_SYS_NAND_BUSWIDTH_16BIT=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_SPANSION=y
--
2.19.2
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH v2 4/4] configs: ti_omap5_common: Add NAND environment settings
2019-02-27 7:59 [U-Boot] [PATCH v2 0/4] Add Support for NAND in dra71x-evm Faiz Abbas
` (2 preceding siblings ...)
2019-02-27 7:59 ` [U-Boot] [PATCH v2 3/4] configs: dra71x-evm: Add Support for NAND Faiz Abbas
@ 2019-02-27 7:59 ` Faiz Abbas
2019-02-27 18:55 ` Tom Rini
2019-04-12 16:30 ` [U-Boot] [U-Boot, v2, " Tom Rini
2019-03-13 15:05 ` [U-Boot] [PATCH v2 0/4] Add Support for NAND in dra71x-evm Faiz Abbas
4 siblings, 2 replies; 12+ messages in thread
From: Faiz Abbas @ 2019-02-27 7:59 UTC (permalink / raw)
To: u-boot
Now that NAND is supported on DRA71x include various NAND environment
settings
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
---
configs/dra7xx_evm_defconfig | 4 +++-
configs/dra7xx_hs_evm_defconfig | 4 +++-
include/configs/dra7xx_evm.h | 2 +-
include/configs/ti_omap5_common.h | 3 ++-
include/environment/ti/nand.h | 26 ++++++++++++++++++++++++++
5 files changed, 35 insertions(+), 4 deletions(-)
create mode 100644 include/environment/ti/nand.h
diff --git a/configs/dra7xx_evm_defconfig b/configs/dra7xx_evm_defconfig
index d71d989c4c..68eab7184e 100644
--- a/configs/dra7xx_evm_defconfig
+++ b/configs/dra7xx_evm_defconfig
@@ -23,13 +23,15 @@ CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_SPL_SYS_MALLOC_SIMPLE=y
CONFIG_SPL_SEPARATE_BSS=y
CONFIG_SPL_DMA_SUPPORT=y
-# CONFIG_SPL_NAND_SUPPORT is not set
CONFIG_SPL_OS_BOOT=y
CONFIG_SPL_SPI_LOAD=y
CONFIG_CMD_SPL=y
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_NAND=y
# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_MTDPARTS=y
+CONFIG_MTDIDS_DEFAULT="nand0=nand.0"
+CONFIG_MTDPARTS_DEFAULT="mtdparts=nand.0:256k(NAND.SPL),256k(NAND.SPL.backup1),256k(NAND.SPL.backup2),256k(NAND.SPL.backup3),256k(NAND.u-boot-spl-os),2m(NAND.u-boot),128k(NAND.u-boot-env),128k(NAND.u-boot-env.backup1),8m(NAND.kernel),-(NAND.file-system)"
CONFIG_OF_CONTROL=y
CONFIG_SPL_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="dra7-evm"
diff --git a/configs/dra7xx_hs_evm_defconfig b/configs/dra7xx_hs_evm_defconfig
index 4642da3c01..076c800332 100644
--- a/configs/dra7xx_hs_evm_defconfig
+++ b/configs/dra7xx_hs_evm_defconfig
@@ -33,7 +33,9 @@ CONFIG_SPL_DMA_SUPPORT=y
CONFIG_SPL_SPI_LOAD=y
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_NAND=y
-# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_MTDPARTS=y
+CONFIG_MTDIDS_DEFAULT="nand0=nand.0"
+CONFIG_MTDPARTS_DEFAULT="mtdparts=nand.0:256k(NAND.SPL),256k(NAND.SPL.backup1),256k(NAND.SPL.backup2),256k(NAND.SPL.backup3),256k(NAND.u-boot-spl-os),2m(NAND.u-boot),128k(NAND.u-boot-env),128k(NAND.u-boot-env.backup1),8m(NAND.kernel),-(NAND.file-system)"
CONFIG_OF_CONTROL=y
CONFIG_SPL_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="dra7-evm"
diff --git a/include/configs/dra7xx_evm.h b/include/configs/dra7xx_evm.h
index f36a9c3e08..955d315608 100644
--- a/include/configs/dra7xx_evm.h
+++ b/include/configs/dra7xx_evm.h
@@ -136,7 +136,7 @@
50, 51, 52, 53, 54, 55, 56, 57, }
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 14
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x000c0000
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x00140000
/* NAND: SPL related configs */
/* NAND: SPL falcon mode configs */
#ifdef CONFIG_SPL_OS_BOOT
diff --git a/include/configs/ti_omap5_common.h b/include/configs/ti_omap5_common.h
index ba57c40182..7c08e47d3d 100644
--- a/include/configs/ti_omap5_common.h
+++ b/include/configs/ti_omap5_common.h
@@ -56,6 +56,7 @@
#include <environment/ti/boot.h>
#include <environment/ti/mmc.h>
+#include <environment/ti/nand.h>
#define CONFIG_EXTRA_ENV_SETTINGS \
DEFAULT_LINUX_BOOT_ENV \
@@ -65,6 +66,7 @@
DEFAULT_FDT_TI_ARGS \
DFUARGS \
NETARGS \
+ NANDARGS \
/*
* SPL related defines. The Public RAM memory map the ROM defines the
@@ -100,7 +102,6 @@
#define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_SDRAM_BASE + \
(128 << 20))
-
#ifdef CONFIG_SPL_BUILD
#undef CONFIG_TIMER
#endif
diff --git a/include/environment/ti/nand.h b/include/environment/ti/nand.h
new file mode 100644
index 0000000000..f838cb3ed1
--- /dev/null
+++ b/include/environment/ti/nand.h
@@ -0,0 +1,26 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com
+ *
+ * Environment variable definitions for NAND on TI boards.
+ */
+
+#ifdef CONFIG_NAND
+#define NANDARGS \
+ "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
+ "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
+ "nandargs=setenv bootargs console=${console} " \
+ "${optargs} " \
+ "root=${nandroot} " \
+ "rootfstype=${nandrootfstype}\0" \
+ "nandroot=ubi0:rootfs rw ubi.mtd=NAND.file-system,2048\0" \
+ "nandrootfstype=ubifs rootwait=1\0" \
+ "nandboot=echo Booting from nand ...; " \
+ "run nandargs; " \
+ "nand read ${fdtaddr} NAND.u-boot-spl-os; " \
+ "nand read ${loadaddr} NAND.kernel; " \
+ "bootz ${loadaddr} - ${fdtaddr}\0"
+#else
+#define NANDARGS ""
+#endif
+
--
2.19.2
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH v2 4/4] configs: ti_omap5_common: Add NAND environment settings
2019-02-27 7:59 ` [U-Boot] [PATCH v2 4/4] configs: ti_omap5_common: Add NAND environment settings Faiz Abbas
@ 2019-02-27 18:55 ` Tom Rini
2019-04-12 16:30 ` [U-Boot] [U-Boot, v2, " Tom Rini
1 sibling, 0 replies; 12+ messages in thread
From: Tom Rini @ 2019-02-27 18:55 UTC (permalink / raw)
To: u-boot
On Wed, Feb 27, 2019 at 01:29:38PM +0530, Faiz Abbas wrote:
> Now that NAND is supported on DRA71x include various NAND environment
> settings
>
> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190227/cec3245c/attachment.sig>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH v2 0/4] Add Support for NAND in dra71x-evm
2019-02-27 7:59 [U-Boot] [PATCH v2 0/4] Add Support for NAND in dra71x-evm Faiz Abbas
` (3 preceding siblings ...)
2019-02-27 7:59 ` [U-Boot] [PATCH v2 4/4] configs: ti_omap5_common: Add NAND environment settings Faiz Abbas
@ 2019-03-13 15:05 ` Faiz Abbas
2019-03-13 16:01 ` Tom Rini
4 siblings, 1 reply; 12+ messages in thread
From: Faiz Abbas @ 2019-03-13 15:05 UTC (permalink / raw)
To: u-boot
Hi,
On 27/02/19 1:29 PM, Faiz Abbas wrote:
> The following patches add support for NAND and booting from
> NAND in dra71x-evm.
>
> v2:
> Patch4: Moved NANDARGS to its own file in include/environment/ti
>
> Faiz Abbas (2):
> configs: dra71x-evm: Add Support for NAND
> configs: ti_omap5_common: Add NAND environment settings
>
> Franklin S Cooper Jr (2):
> board: ti: dra71: Add pinmux settings for NAND on DRA71x EVM
> arm: dra7: Allow NAND to be enabled on DRA71x EVM.
>
> board/ti/dra7xx/evm.c | 56 +++++++++++++++++++++++++++++
> board/ti/dra7xx/mux_data.h | 60 ++++++++++++++++++++++---------
> configs/dra7xx_evm_defconfig | 7 +++-
> configs/dra7xx_hs_evm_defconfig | 7 +++-
> include/configs/dra7xx_evm.h | 2 +-
> include/configs/ti_omap5_common.h | 3 +-
> include/environment/ti/nand.h | 26 ++++++++++++++
> 7 files changed, 141 insertions(+), 20 deletions(-)
> create mode 100644 include/environment/ti/nand.h
>
Gentle ping.
Thanks,
Faiz
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH v2 0/4] Add Support for NAND in dra71x-evm
2019-03-13 15:05 ` [U-Boot] [PATCH v2 0/4] Add Support for NAND in dra71x-evm Faiz Abbas
@ 2019-03-13 16:01 ` Tom Rini
0 siblings, 0 replies; 12+ messages in thread
From: Tom Rini @ 2019-03-13 16:01 UTC (permalink / raw)
To: u-boot
On Wed, Mar 13, 2019 at 08:35:48PM +0530, Faiz Abbas wrote:
> Hi,
>
> On 27/02/19 1:29 PM, Faiz Abbas wrote:
> > The following patches add support for NAND and booting from
> > NAND in dra71x-evm.
> >
> > v2:
> > Patch4: Moved NANDARGS to its own file in include/environment/ti
> >
> > Faiz Abbas (2):
> > configs: dra71x-evm: Add Support for NAND
> > configs: ti_omap5_common: Add NAND environment settings
> >
> > Franklin S Cooper Jr (2):
> > board: ti: dra71: Add pinmux settings for NAND on DRA71x EVM
> > arm: dra7: Allow NAND to be enabled on DRA71x EVM.
> >
> > board/ti/dra7xx/evm.c | 56 +++++++++++++++++++++++++++++
> > board/ti/dra7xx/mux_data.h | 60 ++++++++++++++++++++++---------
> > configs/dra7xx_evm_defconfig | 7 +++-
> > configs/dra7xx_hs_evm_defconfig | 7 +++-
> > include/configs/dra7xx_evm.h | 2 +-
> > include/configs/ti_omap5_common.h | 3 +-
> > include/environment/ti/nand.h | 26 ++++++++++++++
> > 7 files changed, 141 insertions(+), 20 deletions(-)
> > create mode 100644 include/environment/ti/nand.h
> >
>
> Gentle ping.
I reviewed 4/4 and the rest is not appropriate for this point in the
release cycle, thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190313/0448e3fb/attachment.sig>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [U-Boot, v2, 1/4] board: ti: dra71: Add pinmux settings for NAND on DRA71x EVM
2019-02-27 7:59 ` [U-Boot] [PATCH v2 1/4] board: ti: dra71: Add pinmux settings for NAND on DRA71x EVM Faiz Abbas
@ 2019-04-12 16:30 ` Tom Rini
0 siblings, 0 replies; 12+ messages in thread
From: Tom Rini @ 2019-04-12 16:30 UTC (permalink / raw)
To: u-boot
On Wed, Feb 27, 2019 at 01:29:35PM +0530, Faiz Abbas wrote:
> From: Franklin S Cooper Jr <fcooper@ti.com>
>
> By default VOUT3 occupies the pins required for NAND. Therefore, create
> a seperate entry that can be use to reconfigure these pins to work for
> NAND.
>
> On the EVM SWITCH 8 pins 0 and 1 will be used to determine if NAND is
> enabled or not. For NAND to be selected pin 0 should be on and pin 1
> should be off. Any other combination will assume NAND shouldn't be
> enabled.
>
> Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Applied to u-boot/master, thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190412/9f46421c/attachment.sig>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [U-Boot, v2, 2/4] arm: dra7: Allow NAND to be enabled on DRA71x EVM.
2019-02-27 7:59 ` [U-Boot] [PATCH v2 2/4] arm: dra7: Allow NAND to be enabled " Faiz Abbas
@ 2019-04-12 16:30 ` Tom Rini
0 siblings, 0 replies; 12+ messages in thread
From: Tom Rini @ 2019-04-12 16:30 UTC (permalink / raw)
To: u-boot
On Wed, Feb 27, 2019 at 01:29:36PM +0530, Faiz Abbas wrote:
> From: Franklin S Cooper Jr <fcooper@ti.com>
>
> If SW 8 pins 0 and 1 indicate that NAND should be enabled then
> the pins pinmux must be reconfigured for NAND mode.
>
> Therefore, enable NAND by reconfiguring the pinmux.
>
> Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Applied to u-boot/master, thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190412/a5933c76/attachment.sig>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [U-Boot, v2, 3/4] configs: dra71x-evm: Add Support for NAND
2019-02-27 7:59 ` [U-Boot] [PATCH v2 3/4] configs: dra71x-evm: Add Support for NAND Faiz Abbas
@ 2019-04-12 16:30 ` Tom Rini
0 siblings, 0 replies; 12+ messages in thread
From: Tom Rini @ 2019-04-12 16:30 UTC (permalink / raw)
To: u-boot
On Wed, Feb 27, 2019 at 01:29:37PM +0530, Faiz Abbas wrote:
> Add NAND support to dra71x-evm defconfig
>
> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Applied to u-boot/master, thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190412/219aa75b/attachment.sig>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [U-Boot, v2, 4/4] configs: ti_omap5_common: Add NAND environment settings
2019-02-27 7:59 ` [U-Boot] [PATCH v2 4/4] configs: ti_omap5_common: Add NAND environment settings Faiz Abbas
2019-02-27 18:55 ` Tom Rini
@ 2019-04-12 16:30 ` Tom Rini
1 sibling, 0 replies; 12+ messages in thread
From: Tom Rini @ 2019-04-12 16:30 UTC (permalink / raw)
To: u-boot
On Wed, Feb 27, 2019 at 01:29:38PM +0530, Faiz Abbas wrote:
> Now that NAND is supported on DRA71x include various NAND environment
> settings
>
> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
> Reviewed-by: Tom Rini <trini@konsulko.com>
Applied to u-boot/master, thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190412/ebffb377/attachment.sig>
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2019-04-12 16:30 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-02-27 7:59 [U-Boot] [PATCH v2 0/4] Add Support for NAND in dra71x-evm Faiz Abbas
2019-02-27 7:59 ` [U-Boot] [PATCH v2 1/4] board: ti: dra71: Add pinmux settings for NAND on DRA71x EVM Faiz Abbas
2019-04-12 16:30 ` [U-Boot] [U-Boot, v2, " Tom Rini
2019-02-27 7:59 ` [U-Boot] [PATCH v2 2/4] arm: dra7: Allow NAND to be enabled " Faiz Abbas
2019-04-12 16:30 ` [U-Boot] [U-Boot, v2, " Tom Rini
2019-02-27 7:59 ` [U-Boot] [PATCH v2 3/4] configs: dra71x-evm: Add Support for NAND Faiz Abbas
2019-04-12 16:30 ` [U-Boot] [U-Boot, v2, " Tom Rini
2019-02-27 7:59 ` [U-Boot] [PATCH v2 4/4] configs: ti_omap5_common: Add NAND environment settings Faiz Abbas
2019-02-27 18:55 ` Tom Rini
2019-04-12 16:30 ` [U-Boot] [U-Boot, v2, " Tom Rini
2019-03-13 15:05 ` [U-Boot] [PATCH v2 0/4] Add Support for NAND in dra71x-evm Faiz Abbas
2019-03-13 16:01 ` Tom Rini
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.