[PATCH] ARM: sun8i: h3: bluetooth for Banana Pi M2 Zero board

All of lore.kernel.org
 help / color / mirror / Atom feed

* [PATCH] ARM: sun8i: h3: bluetooth for Banana Pi M2 Zero board
@ 2019-02-28 21:28 ` Andreas Kemnade
  0 siblings, 0 replies; 6+ messages in thread
From: Andreas Kemnade @ 2019-02-28 21:28 UTC (permalink / raw)
  To: robh+dt, mark.rutland, maxime.ripard, wens, devicetree,
	linux-arm-kernel, linux-kernel
  Cc: Andreas Kemnade

The Banana Pi M2 Zero board has an AP6212 BT+Wifi combo chip
with broadcom internals attached to UART1 and some gpios.
This addition is in line with similar boards

Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
---
 .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts    | 29 ++++++++++++++++++++++
 1 file changed, 29 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
index 1db2541135a7..39e206fac4e3 100644
--- a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
+++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
@@ -69,6 +69,8 @@
 		compatible = "mmc-pwrseq-simple";
 		pinctrl-names = "default";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+		clocks = <&rtc 1>;
+		clock-names = "ext_clock";
 	};
 };
 
@@ -122,7 +124,34 @@
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	uart-has-rtscts;
 	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_pins_out>, <&bt_pins_in>;
+		clocks = <&rtc 1>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_vcc3v3>;
+		vddio-supply = <&reg_vcc3v3>;
+		device-wakeup-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
+		host-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
+		shutdown-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	};
+
+};
+
+&pio {
+	bt_pins_out: bt_out {
+		pins = "PG12", "PG13";
+		function = "gpio_out";
+	};
+
+	bt_pins_in: bt_in {
+		pins = "PG11";
+		function = "gpio_in";
+	};
 };
 
 &usb_otg {
-- 
2.11.0


^ permalink raw reply related	[flat|nested] 6+ messages in thread

* [PATCH] ARM: sun8i: h3: bluetooth for Banana Pi M2 Zero board
@ 2019-02-28 21:28 ` Andreas Kemnade
  0 siblings, 0 replies; 6+ messages in thread
From: Andreas Kemnade @ 2019-02-28 21:28 UTC (permalink / raw)
  To: robh+dt, mark.rutland, maxime.ripard, wens, devicetree,
	linux-arm-kernel, linux-kernel
  Cc: Andreas Kemnade

The Banana Pi M2 Zero board has an AP6212 BT+Wifi combo chip
with broadcom internals attached to UART1 and some gpios.
This addition is in line with similar boards

Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
---
 .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts    | 29 ++++++++++++++++++++++
 1 file changed, 29 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
index 1db2541135a7..39e206fac4e3 100644
--- a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
+++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
@@ -69,6 +69,8 @@
 		compatible = "mmc-pwrseq-simple";
 		pinctrl-names = "default";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+		clocks = <&rtc 1>;
+		clock-names = "ext_clock";
 	};
 };
 
@@ -122,7 +124,34 @@
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	uart-has-rtscts;
 	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_pins_out>, <&bt_pins_in>;
+		clocks = <&rtc 1>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_vcc3v3>;
+		vddio-supply = <&reg_vcc3v3>;
+		device-wakeup-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
+		host-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
+		shutdown-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	};
+
+};
+
+&pio {
+	bt_pins_out: bt_out {
+		pins = "PG12", "PG13";
+		function = "gpio_out";
+	};
+
+	bt_pins_in: bt_in {
+		pins = "PG11";
+		function = "gpio_in";
+	};
 };
 
 &usb_otg {
-- 
2.11.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 6+ messages in thread

* Re: [PATCH] ARM: sun8i: h3: bluetooth for Banana Pi M2 Zero board
  2019-02-28 21:28 ` Andreas Kemnade
@ 2019-03-01 14:36   ` Maxime Ripard
  -1 siblings, 0 replies; 6+ messages in thread
From: Maxime Ripard @ 2019-03-01 14:36 UTC (permalink / raw)
  To: Andreas Kemnade
  Cc: robh+dt, mark.rutland, wens, devicetree, linux-arm-kernel, linux-kernel

[-- Attachment #1: Type: text/plain, Size: 2008 bytes --]

Hi,

Thanks for your patch

On Thu, Feb 28, 2019 at 10:28:40PM +0100, Andreas Kemnade wrote:
> The Banana Pi M2 Zero board has an AP6212 BT+Wifi combo chip
> with broadcom internals attached to UART1 and some gpios.
> This addition is in line with similar boards
> 
> Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
> ---
>  .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts    | 29 ++++++++++++++++++++++
>  1 file changed, 29 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> index 1db2541135a7..39e206fac4e3 100644
> --- a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> @@ -69,6 +69,8 @@
>  		compatible = "mmc-pwrseq-simple";
>  		pinctrl-names = "default";
>  		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
> +		clocks = <&rtc 1>;
> +		clock-names = "ext_clock";
>  	};
>  };
>  
> @@ -122,7 +124,34 @@
>  &uart1 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
> +	uart-has-rtscts;
>  	status = "okay";
> +
> +	bluetooth {
> +		compatible = "brcm,bcm43438-bt";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&bt_pins_out>, <&bt_pins_in>;
> +		clocks = <&rtc 1>;
> +		clock-names = "lpo";
> +		vbat-supply = <&reg_vcc3v3>;
> +		vddio-supply = <&reg_vcc3v3>;
> +		device-wakeup-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
> +		host-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
> +		shutdown-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
> +	};
> +
> +};
> +
> +&pio {
> +	bt_pins_out: bt_out {
> +		pins = "PG12", "PG13";
> +		function = "gpio_out";
> +	};
> +
> +	bt_pins_in: bt_in {
> +		pins = "PG11";
> +		function = "gpio_in";
> +	};

You don't need any of those pinctrl nodes, GPIOs work fine without.

Maxime

-- 
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH] ARM: sun8i: h3: bluetooth for Banana Pi M2 Zero board
@ 2019-03-01 14:36   ` Maxime Ripard
  0 siblings, 0 replies; 6+ messages in thread
From: Maxime Ripard @ 2019-03-01 14:36 UTC (permalink / raw)
  To: Andreas Kemnade
  Cc: mark.rutland, devicetree, linux-kernel, wens, robh+dt, linux-arm-kernel


[-- Attachment #1.1: Type: text/plain, Size: 2008 bytes --]

Hi,

Thanks for your patch

On Thu, Feb 28, 2019 at 10:28:40PM +0100, Andreas Kemnade wrote:
> The Banana Pi M2 Zero board has an AP6212 BT+Wifi combo chip
> with broadcom internals attached to UART1 and some gpios.
> This addition is in line with similar boards
> 
> Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
> ---
>  .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts    | 29 ++++++++++++++++++++++
>  1 file changed, 29 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> index 1db2541135a7..39e206fac4e3 100644
> --- a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> @@ -69,6 +69,8 @@
>  		compatible = "mmc-pwrseq-simple";
>  		pinctrl-names = "default";
>  		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
> +		clocks = <&rtc 1>;
> +		clock-names = "ext_clock";
>  	};
>  };
>  
> @@ -122,7 +124,34 @@
>  &uart1 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
> +	uart-has-rtscts;
>  	status = "okay";
> +
> +	bluetooth {
> +		compatible = "brcm,bcm43438-bt";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&bt_pins_out>, <&bt_pins_in>;
> +		clocks = <&rtc 1>;
> +		clock-names = "lpo";
> +		vbat-supply = <&reg_vcc3v3>;
> +		vddio-supply = <&reg_vcc3v3>;
> +		device-wakeup-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
> +		host-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
> +		shutdown-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
> +	};
> +
> +};
> +
> +&pio {
> +	bt_pins_out: bt_out {
> +		pins = "PG12", "PG13";
> +		function = "gpio_out";
> +	};
> +
> +	bt_pins_in: bt_in {
> +		pins = "PG11";
> +		function = "gpio_in";
> +	};

You don't need any of those pinctrl nodes, GPIOs work fine without.

Maxime

-- 
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH] ARM: sun8i: h3: bluetooth for Banana Pi M2 Zero board
  2019-03-01 14:36   ` Maxime Ripard
@ 2019-03-01 16:42     ` Andreas Kemnade
  -1 siblings, 0 replies; 6+ messages in thread
From: Andreas Kemnade @ 2019-03-01 16:42 UTC (permalink / raw)
  To: Maxime Ripard
  Cc: robh+dt, mark.rutland, wens, devicetree, linux-arm-kernel, linux-kernel

[-- Attachment #1: Type: text/plain, Size: 2207 bytes --]

On Fri, 1 Mar 2019 15:36:32 +0100
Maxime Ripard <maxime.ripard@bootlin.com> wrote:

> Hi,
> 
> Thanks for your patch
> 
> On Thu, Feb 28, 2019 at 10:28:40PM +0100, Andreas Kemnade wrote:
> > The Banana Pi M2 Zero board has an AP6212 BT+Wifi combo chip
> > with broadcom internals attached to UART1 and some gpios.
> > This addition is in line with similar boards
> > 
> > Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
> > ---
> >  .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts    | 29 ++++++++++++++++++++++
> >  1 file changed, 29 insertions(+)
> > 
> > diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> > index 1db2541135a7..39e206fac4e3 100644
> > --- a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> > +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> > @@ -69,6 +69,8 @@
> >  		compatible = "mmc-pwrseq-simple";
> >  		pinctrl-names = "default";
> >  		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
> > +		clocks = <&rtc 1>;
> > +		clock-names = "ext_clock";
> >  	};
> >  };
> >  
> > @@ -122,7 +124,34 @@
> >  &uart1 {
> >  	pinctrl-names = "default";
> >  	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
> > +	uart-has-rtscts;
> >  	status = "okay";
> > +
> > +	bluetooth {
> > +		compatible = "brcm,bcm43438-bt";
> > +		pinctrl-names = "default";
> > +		pinctrl-0 = <&bt_pins_out>, <&bt_pins_in>;
> > +		clocks = <&rtc 1>;
> > +		clock-names = "lpo";
> > +		vbat-supply = <&reg_vcc3v3>;
> > +		vddio-supply = <&reg_vcc3v3>;
> > +		device-wakeup-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
> > +		host-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
> > +		shutdown-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
> > +	};
> > +
> > +};
> > +
> > +&pio {
> > +	bt_pins_out: bt_out {
> > +		pins = "PG12", "PG13";
> > +		function = "gpio_out";
> > +	};
> > +
> > +	bt_pins_in: bt_in {
> > +		pins = "PG11";
> > +		function = "gpio_in";
> > +	};  
> 
> You don't need any of those pinctrl nodes, GPIOs work fine without.
> 
ok, that makes things easier. I will resend a v2 without them.

Regards,
Andreas

[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH] ARM: sun8i: h3: bluetooth for Banana Pi M2 Zero board
@ 2019-03-01 16:42     ` Andreas Kemnade
  0 siblings, 0 replies; 6+ messages in thread
From: Andreas Kemnade @ 2019-03-01 16:42 UTC (permalink / raw)
  To: Maxime Ripard
  Cc: mark.rutland, devicetree, linux-kernel, wens, robh+dt, linux-arm-kernel


[-- Attachment #1.1: Type: text/plain, Size: 2207 bytes --]

On Fri, 1 Mar 2019 15:36:32 +0100
Maxime Ripard <maxime.ripard@bootlin.com> wrote:

> Hi,
> 
> Thanks for your patch
> 
> On Thu, Feb 28, 2019 at 10:28:40PM +0100, Andreas Kemnade wrote:
> > The Banana Pi M2 Zero board has an AP6212 BT+Wifi combo chip
> > with broadcom internals attached to UART1 and some gpios.
> > This addition is in line with similar boards
> > 
> > Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
> > ---
> >  .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts    | 29 ++++++++++++++++++++++
> >  1 file changed, 29 insertions(+)
> > 
> > diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> > index 1db2541135a7..39e206fac4e3 100644
> > --- a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> > +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> > @@ -69,6 +69,8 @@
> >  		compatible = "mmc-pwrseq-simple";
> >  		pinctrl-names = "default";
> >  		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
> > +		clocks = <&rtc 1>;
> > +		clock-names = "ext_clock";
> >  	};
> >  };
> >  
> > @@ -122,7 +124,34 @@
> >  &uart1 {
> >  	pinctrl-names = "default";
> >  	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
> > +	uart-has-rtscts;
> >  	status = "okay";
> > +
> > +	bluetooth {
> > +		compatible = "brcm,bcm43438-bt";
> > +		pinctrl-names = "default";
> > +		pinctrl-0 = <&bt_pins_out>, <&bt_pins_in>;
> > +		clocks = <&rtc 1>;
> > +		clock-names = "lpo";
> > +		vbat-supply = <&reg_vcc3v3>;
> > +		vddio-supply = <&reg_vcc3v3>;
> > +		device-wakeup-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
> > +		host-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
> > +		shutdown-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
> > +	};
> > +
> > +};
> > +
> > +&pio {
> > +	bt_pins_out: bt_out {
> > +		pins = "PG12", "PG13";
> > +		function = "gpio_out";
> > +	};
> > +
> > +	bt_pins_in: bt_in {
> > +		pins = "PG11";
> > +		function = "gpio_in";
> > +	};  
> 
> You don't need any of those pinctrl nodes, GPIOs work fine without.
> 
ok, that makes things easier. I will resend a v2 without them.

Regards,
Andreas

[-- Attachment #1.2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 6+ messages in thread

end of thread, other threads:[~2019-03-01 16:43 UTC | newest]

Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-02-28 21:28 [PATCH] ARM: sun8i: h3: bluetooth for Banana Pi M2 Zero board Andreas Kemnade
2019-02-28 21:28 ` Andreas Kemnade
2019-03-01 14:36 ` Maxime Ripard
2019-03-01 14:36   ` Maxime Ripard
2019-03-01 16:42   ` Andreas Kemnade
2019-03-01 16:42     ` Andreas Kemnade

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.