[PATCH v3 0/5] Add support for drm/rockchip to dynamically control the DDR frequency.

[PATCH v3 0/5] Add support for drm/rockchip to dynamically control the DDR frequency.

[Gaël PORTAY]

Dear all,

The rk3399 platform has a DFI controller that can monitor DDR load and a
DMC driver that talks with the TF-A (Trusted Firmware-A) to dynamically
set the DDR frequency with following flow.

             kernel                          Trusted Firmware-A
                                                  (bl31)
        monitor ddr load
                |
                |
        get_target_rate
                |
                |           pass rate to TF-A
        clk_set_rate(ddr) --------------------->run ddr dvs flow
                                                    |
                                                    |
                 <------------------------------end ddr dvs flow
                |
                |
              return

These patches add support for devfreq to dynamically control the DDR
frequency into the drm rockchip driver. By default it uses the
'simple_ondemand' governor which can adjust the frequency based on the
DDR load.

Waiting for your feedback.

Best regards,
Gaël

Changes in v3:
- [PATCH v2 1/5] Add Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>.
- [PATCH v2 2/5] Add Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>.
- [PATCH v2 3/5] Add Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>.
		 Remove comments.
		 Move pmu dt parsing after dt-parsing of timings to fix
		  data->odt_dis_freq value.
- [PATCH v2 5/5] Remove display_subsystem nodes.

Changes in v2:
- [PATCH 1/8] Really add Acked-by: Chanwoo Choi <cw00.choi@samsung.com>.
- [PATCH 4/8] Removed from patchset.
- [PATCH 5/8] Removed from patchset.
- [PATCH 6/8] Removed from patchset.
- [PATCH 7/8] Reword the commit message to reflect the removal of
              rk3390-dram-default-timing.dts in v1.
- [PATCH 8/8] Move center-supply attribute of dmc node in file
              rk3399-gru-chromebook.dtsi (where ppvar_centerlogic is
	      defined).

Changes in v1:
- [RFC 1/10] Add Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
- [RFC 1/10] s/Generic/General/ (Robin Murphy)
- [RFC 2/10] Add reviewed and acked tags from Chanwoo Choi and Rob Herring
- [RFC 3/10] Add an explanation for platform SIP calls.
- [RFC 3/10] Change if statement for a switch.
- [RFC 3/10] Rename ddr_flag to odt_enable to be more clear.
- [RFC 4/10] Removed from the series. I did not found a use case where not holding the mutex causes the issue.
- [RFC 7/10] Removed from the series. I did not found a use case where this matters.
- [RFC 8/10] Move rk3399-dram.h to dt-includes.
- [RFC 8/10] Put sdram default values under the dmc node.
- [RFC 8/10] Removed rk3399-dram-default-timing.dts


Enric Balletbo i Serra (3):
  devfreq: rockchip-dfi: Move GRF definitions to a common place.
  dt-bindings: devfreq: rk3399_dmc: Add rockchip,pmu phandle.
  devfreq: rk3399_dmc: Pass ODT and auto power down parameters to TF-A.

Lin Huang (2):
  arm64: dts: rk3399: Add dfi and dmc nodes.
  arm64: dts: rockchip: Enable dmc and dfi nodes on gru.

 .../bindings/devfreq/rk3399_dmc.txt           |  2 +
 .../dts/rockchip/rk3399-gru-chromebook.dtsi   |  4 +
 arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi  | 16 ++++
 .../boot/dts/rockchip/rk3399-op1-opp.dtsi     | 29 ++++++++
 arch/arm64/boot/dts/rockchip/rk3399.dtsi      | 49 +++++++++++++
 drivers/devfreq/event/rockchip-dfi.c          | 23 ++----
 drivers/devfreq/rk3399_dmc.c                  | 71 +++++++++++++++++-
 include/dt-bindings/power/rk3399-dram.h       | 73 +++++++++++++++++++
 include/soc/rockchip/rk3399_grf.h             | 21 ++++++
 include/soc/rockchip/rockchip_sip.h           |  1 +
 10 files changed, 272 insertions(+), 17 deletions(-)
 create mode 100644 include/dt-bindings/power/rk3399-dram.h
 create mode 100644 include/soc/rockchip/rk3399_grf.h

-- 
2.21.0

[PATCH v3 0/5] Add support for drm/rockchip to dynamically control the DDR frequency.

[Gaël PORTAY]

Dear all,

The rk3399 platform has a DFI controller that can monitor DDR load and a
DMC driver that talks with the TF-A (Trusted Firmware-A) to dynamically
set the DDR frequency with following flow.

             kernel                          Trusted Firmware-A
                                                  (bl31)
        monitor ddr load
                |
                |
        get_target_rate
                |
                |           pass rate to TF-A
        clk_set_rate(ddr) --------------------->run ddr dvs flow
                                                    |
                                                    |
                 <------------------------------end ddr dvs flow
                |
                |
              return

These patches add support for devfreq to dynamically control the DDR
frequency into the drm rockchip driver. By default it uses the
'simple_ondemand' governor which can adjust the frequency based on the
DDR load.

Waiting for your feedback.

Best regards,
Gaël

Changes in v3:
- [PATCH v2 1/5] Add Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>.
- [PATCH v2 2/5] Add Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>.
- [PATCH v2 3/5] Add Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>.
		 Remove comments.
		 Move pmu dt parsing after dt-parsing of timings to fix
		  data->odt_dis_freq value.
- [PATCH v2 5/5] Remove display_subsystem nodes.

Changes in v2:
- [PATCH 1/8] Really add Acked-by: Chanwoo Choi <cw00.choi@samsung.com>.
- [PATCH 4/8] Removed from patchset.
- [PATCH 5/8] Removed from patchset.
- [PATCH 6/8] Removed from patchset.
- [PATCH 7/8] Reword the commit message to reflect the removal of
              rk3390-dram-default-timing.dts in v1.
- [PATCH 8/8] Move center-supply attribute of dmc node in file
              rk3399-gru-chromebook.dtsi (where ppvar_centerlogic is
	      defined).

Changes in v1:
- [RFC 1/10] Add Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
- [RFC 1/10] s/Generic/General/ (Robin Murphy)
- [RFC 2/10] Add reviewed and acked tags from Chanwoo Choi and Rob Herring
- [RFC 3/10] Add an explanation for platform SIP calls.
- [RFC 3/10] Change if statement for a switch.
- [RFC 3/10] Rename ddr_flag to odt_enable to be more clear.
- [RFC 4/10] Removed from the series. I did not found a use case where not holding the mutex causes the issue.
- [RFC 7/10] Removed from the series. I did not found a use case where this matters.
- [RFC 8/10] Move rk3399-dram.h to dt-includes.
- [RFC 8/10] Put sdram default values under the dmc node.
- [RFC 8/10] Removed rk3399-dram-default-timing.dts


Enric Balletbo i Serra (3):
  devfreq: rockchip-dfi: Move GRF definitions to a common place.
  dt-bindings: devfreq: rk3399_dmc: Add rockchip,pmu phandle.
  devfreq: rk3399_dmc: Pass ODT and auto power down parameters to TF-A.

Lin Huang (2):
  arm64: dts: rk3399: Add dfi and dmc nodes.
  arm64: dts: rockchip: Enable dmc and dfi nodes on gru.

 .../bindings/devfreq/rk3399_dmc.txt           |  2 +
 .../dts/rockchip/rk3399-gru-chromebook.dtsi   |  4 +
 arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi  | 16 ++++
 .../boot/dts/rockchip/rk3399-op1-opp.dtsi     | 29 ++++++++
 arch/arm64/boot/dts/rockchip/rk3399.dtsi      | 49 +++++++++++++
 drivers/devfreq/event/rockchip-dfi.c          | 23 ++----
 drivers/devfreq/rk3399_dmc.c                  | 71 +++++++++++++++++-
 include/dt-bindings/power/rk3399-dram.h       | 73 +++++++++++++++++++
 include/soc/rockchip/rk3399_grf.h             | 21 ++++++
 include/soc/rockchip/rockchip_sip.h           |  1 +
 10 files changed, 272 insertions(+), 17 deletions(-)
 create mode 100644 include/dt-bindings/power/rk3399-dram.h
 create mode 100644 include/soc/rockchip/rk3399_grf.h

-- 
2.21.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 1/5] devfreq: rockchip-dfi: Move GRF definitions to a common place.

[Gaël PORTAY]

From: Enric Balletbo i Serra <enric.balletbo@collabora.com>

Some rk3399 GRF (Generic Register Files) definitions can be used for
different drivers. Move these definitions to a common include so we
don't need to duplicate these definitions.

Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
---

Changes in v3:
- [PATCH v2 1/5] Add Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>.

Changes in v2:
- [PATCH 1/8] Really add Acked-by: Chanwoo Choi <cw00.choi@samsung.com>.

Changes in v1:
- [RFC 1/10] Add Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
- [RFC 1/10] s/Generic/General/ (Robin Murphy)
- [RFC 4/10] Removed from the series. I did not found a use case where not holding the mutex causes the issue.
- [RFC 7/10] Removed from the series. I did not found a use case where this matters.

 drivers/devfreq/event/rockchip-dfi.c | 23 +++++++----------------
 include/soc/rockchip/rk3399_grf.h    | 21 +++++++++++++++++++++
 2 files changed, 28 insertions(+), 16 deletions(-)
 create mode 100644 include/soc/rockchip/rk3399_grf.h

diff --git a/drivers/devfreq/event/rockchip-dfi.c b/drivers/devfreq/event/rockchip-dfi.c
index 22b113363ffc..2fbbcbeb644f 100644
--- a/drivers/devfreq/event/rockchip-dfi.c
+++ b/drivers/devfreq/event/rockchip-dfi.c
@@ -26,6 +26,8 @@
 #include <linux/list.h>
 #include <linux/of.h>
 
+#include <soc/rockchip/rk3399_grf.h>
+
 #define RK3399_DMC_NUM_CH	2
 
 /* DDRMON_CTRL */
@@ -43,18 +45,6 @@
 #define DDRMON_CH1_COUNT_NUM		0x3c
 #define DDRMON_CH1_DFI_ACCESS_NUM	0x40
 
-/* pmu grf */
-#define PMUGRF_OS_REG2	0x308
-#define DDRTYPE_SHIFT	13
-#define DDRTYPE_MASK	7
-
-enum {
-	DDR3 = 3,
-	LPDDR3 = 6,
-	LPDDR4 = 7,
-	UNUSED = 0xFF
-};
-
 struct dmc_usage {
 	u32 access;
 	u32 total;
@@ -83,16 +73,17 @@ static void rockchip_dfi_start_hardware_counter(struct devfreq_event_dev *edev)
 	u32 ddr_type;
 
 	/* get ddr type */
-	regmap_read(info->regmap_pmu, PMUGRF_OS_REG2, &val);
-	ddr_type = (val >> DDRTYPE_SHIFT) & DDRTYPE_MASK;
+	regmap_read(info->regmap_pmu, RK3399_PMUGRF_OS_REG2, &val);
+	ddr_type = (val >> RK3399_PMUGRF_DDRTYPE_SHIFT) &
+		    RK3399_PMUGRF_DDRTYPE_MASK;
 
 	/* clear DDRMON_CTRL setting */
 	writel_relaxed(CLR_DDRMON_CTRL, dfi_regs + DDRMON_CTRL);
 
 	/* set ddr type to dfi */
-	if (ddr_type == LPDDR3)
+	if (ddr_type == RK3399_PMUGRF_DDRTYPE_LPDDR3)
 		writel_relaxed(LPDDR3_EN, dfi_regs + DDRMON_CTRL);
-	else if (ddr_type == LPDDR4)
+	else if (ddr_type == RK3399_PMUGRF_DDRTYPE_LPDDR4)
 		writel_relaxed(LPDDR4_EN, dfi_regs + DDRMON_CTRL);
 
 	/* enable count, use software mode */
diff --git a/include/soc/rockchip/rk3399_grf.h b/include/soc/rockchip/rk3399_grf.h
new file mode 100644
index 000000000000..3eebabcb2812
--- /dev/null
+++ b/include/soc/rockchip/rk3399_grf.h
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Rockchip General Register Files definitions
+ *
+ * Copyright (c) 2018, Collabora Ltd.
+ * Author: Enric Balletbo i Serra <enric.balletbo@collabora.com>
+ */
+
+#ifndef __SOC_RK3399_GRF_H
+#define __SOC_RK3399_GRF_H
+
+/* PMU GRF Registers */
+#define RK3399_PMUGRF_OS_REG2		0x308
+#define RK3399_PMUGRF_DDRTYPE_SHIFT	13
+#define RK3399_PMUGRF_DDRTYPE_MASK	7
+#define RK3399_PMUGRF_DDRTYPE_DDR3	3
+#define RK3399_PMUGRF_DDRTYPE_LPDDR2	5
+#define RK3399_PMUGRF_DDRTYPE_LPDDR3	6
+#define RK3399_PMUGRF_DDRTYPE_LPDDR4	7
+
+#endif
-- 
2.21.0

[PATCH v3 1/5] devfreq: rockchip-dfi: Move GRF definitions to a common place.

[Gaël PORTAY]

From: Enric Balletbo i Serra <enric.balletbo@collabora.com>

Some rk3399 GRF (Generic Register Files) definitions can be used for
different drivers. Move these definitions to a common include so we
don't need to duplicate these definitions.

Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
---

Changes in v3:
- [PATCH v2 1/5] Add Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>.

Changes in v2:
- [PATCH 1/8] Really add Acked-by: Chanwoo Choi <cw00.choi@samsung.com>.

Changes in v1:
- [RFC 1/10] Add Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
- [RFC 1/10] s/Generic/General/ (Robin Murphy)
- [RFC 4/10] Removed from the series. I did not found a use case where not holding the mutex causes the issue.
- [RFC 7/10] Removed from the series. I did not found a use case where this matters.

 drivers/devfreq/event/rockchip-dfi.c | 23 +++++++----------------
 include/soc/rockchip/rk3399_grf.h    | 21 +++++++++++++++++++++
 2 files changed, 28 insertions(+), 16 deletions(-)
 create mode 100644 include/soc/rockchip/rk3399_grf.h

diff --git a/drivers/devfreq/event/rockchip-dfi.c b/drivers/devfreq/event/rockchip-dfi.c
index 22b113363ffc..2fbbcbeb644f 100644
--- a/drivers/devfreq/event/rockchip-dfi.c
+++ b/drivers/devfreq/event/rockchip-dfi.c
@@ -26,6 +26,8 @@
 #include <linux/list.h>
 #include <linux/of.h>
 
+#include <soc/rockchip/rk3399_grf.h>
+
 #define RK3399_DMC_NUM_CH	2
 
 /* DDRMON_CTRL */
@@ -43,18 +45,6 @@
 #define DDRMON_CH1_COUNT_NUM		0x3c
 #define DDRMON_CH1_DFI_ACCESS_NUM	0x40
 
-/* pmu grf */
-#define PMUGRF_OS_REG2	0x308
-#define DDRTYPE_SHIFT	13
-#define DDRTYPE_MASK	7
-
-enum {
-	DDR3 = 3,
-	LPDDR3 = 6,
-	LPDDR4 = 7,
-	UNUSED = 0xFF
-};
-
 struct dmc_usage {
 	u32 access;
 	u32 total;
@@ -83,16 +73,17 @@ static void rockchip_dfi_start_hardware_counter(struct devfreq_event_dev *edev)
 	u32 ddr_type;
 
 	/* get ddr type */
-	regmap_read(info->regmap_pmu, PMUGRF_OS_REG2, &val);
-	ddr_type = (val >> DDRTYPE_SHIFT) & DDRTYPE_MASK;
+	regmap_read(info->regmap_pmu, RK3399_PMUGRF_OS_REG2, &val);
+	ddr_type = (val >> RK3399_PMUGRF_DDRTYPE_SHIFT) &
+		    RK3399_PMUGRF_DDRTYPE_MASK;
 
 	/* clear DDRMON_CTRL setting */
 	writel_relaxed(CLR_DDRMON_CTRL, dfi_regs + DDRMON_CTRL);
 
 	/* set ddr type to dfi */
-	if (ddr_type == LPDDR3)
+	if (ddr_type == RK3399_PMUGRF_DDRTYPE_LPDDR3)
 		writel_relaxed(LPDDR3_EN, dfi_regs + DDRMON_CTRL);
-	else if (ddr_type == LPDDR4)
+	else if (ddr_type == RK3399_PMUGRF_DDRTYPE_LPDDR4)
 		writel_relaxed(LPDDR4_EN, dfi_regs + DDRMON_CTRL);
 
 	/* enable count, use software mode */
diff --git a/include/soc/rockchip/rk3399_grf.h b/include/soc/rockchip/rk3399_grf.h
new file mode 100644
index 000000000000..3eebabcb2812
--- /dev/null
+++ b/include/soc/rockchip/rk3399_grf.h
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Rockchip General Register Files definitions
+ *
+ * Copyright (c) 2018, Collabora Ltd.
+ * Author: Enric Balletbo i Serra <enric.balletbo@collabora.com>
+ */
+
+#ifndef __SOC_RK3399_GRF_H
+#define __SOC_RK3399_GRF_H
+
+/* PMU GRF Registers */
+#define RK3399_PMUGRF_OS_REG2		0x308
+#define RK3399_PMUGRF_DDRTYPE_SHIFT	13
+#define RK3399_PMUGRF_DDRTYPE_MASK	7
+#define RK3399_PMUGRF_DDRTYPE_DDR3	3
+#define RK3399_PMUGRF_DDRTYPE_LPDDR2	5
+#define RK3399_PMUGRF_DDRTYPE_LPDDR3	6
+#define RK3399_PMUGRF_DDRTYPE_LPDDR4	7
+
+#endif
-- 
2.21.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 2/5] dt-bindings: devfreq: rk3399_dmc: Add rockchip,pmu phandle.

[Gaël PORTAY]

From: Enric Balletbo i Serra <enric.balletbo@collabora.com>

The Rockchip DMC (Dynamic Memory Interface) needs to access to the PMU
general register files to know the DRAM type, so add a phandle to the
syscon that manages these registers.

Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
---

Changes in v3:
- [PATCH v2 2/5] Add Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>.

Changes in v2: None

Changes in v1:
- [RFC 2/10] Add reviewed and acked tags from Chanwoo Choi and Rob Herring

 Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt
index 0ec68141f85a..951789c0cdd6 100644
--- a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt
+++ b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt
@@ -12,6 +12,8 @@ Required properties:
 			 for details.
 - center-supply:	 DMC supply node.
 - status:		 Marks the node enabled/disabled.
+- rockchip,pmu:		 Phandle to the syscon managing the "PMU general register
+			 files".
 
 Optional properties:
 - interrupts:		 The CPU interrupt number. The interrupt specifier
-- 
2.21.0

[PATCH v3 2/5] dt-bindings: devfreq: rk3399_dmc: Add rockchip, pmu phandle.

[Gaël PORTAY]

From: Enric Balletbo i Serra <enric.balletbo@collabora.com>

The Rockchip DMC (Dynamic Memory Interface) needs to access to the PMU
general register files to know the DRAM type, so add a phandle to the
syscon that manages these registers.

Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
---

Changes in v3:
- [PATCH v2 2/5] Add Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>.

Changes in v2: None

Changes in v1:
- [RFC 2/10] Add reviewed and acked tags from Chanwoo Choi and Rob Herring

 Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt
index 0ec68141f85a..951789c0cdd6 100644
--- a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt
+++ b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt
@@ -12,6 +12,8 @@ Required properties:
 			 for details.
 - center-supply:	 DMC supply node.
 - status:		 Marks the node enabled/disabled.
+- rockchip,pmu:		 Phandle to the syscon managing the "PMU general register
+			 files".
 
 Optional properties:
 - interrupts:		 The CPU interrupt number. The interrupt specifier
-- 
2.21.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 3/5] devfreq: rk3399_dmc: Pass ODT and auto power down parameters to TF-A.

[Gaël PORTAY]

From: Enric Balletbo i Serra <enric.balletbo@collabora.com>

Trusted Firmware-A (TF-A) for rk3399 implements a SiP call to get the
on-die termination (ODT) and auto power down parameters from kernel,
this patch adds the functionality to do this. Also, if DDR clock
frequency is lower than the on-die termination (ODT) disable frequency
this driver should disable the DDR ODT.

Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
---

Changes in v3:
- [PATCH v2 3/5] Add Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>.
		 Remove comments.
		 Move pmu dt parsing after dt-parsing of timings to fix
		  data->odt_dis_freq value.

Changes in v2: None

Changes in v1:
- [RFC 3/10] Add an explanation for platform SIP calls.
- [RFC 3/10] Change if statement for a switch.
- [RFC 3/10] Rename ddr_flag to odt_enable to be more clear.

 drivers/devfreq/rk3399_dmc.c        | 71 ++++++++++++++++++++++++++++-
 include/soc/rockchip/rockchip_sip.h |  1 +
 2 files changed, 71 insertions(+), 1 deletion(-)

diff --git a/drivers/devfreq/rk3399_dmc.c b/drivers/devfreq/rk3399_dmc.c
index e795ad2b3f6b..daf19e121c99 100644
--- a/drivers/devfreq/rk3399_dmc.c
+++ b/drivers/devfreq/rk3399_dmc.c
@@ -18,14 +18,17 @@
 #include <linux/devfreq.h>
 #include <linux/devfreq-event.h>
 #include <linux/interrupt.h>
+#include <linux/mfd/syscon.h>
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/pm_opp.h>
+#include <linux/regmap.h>
 #include <linux/regulator/consumer.h>
 #include <linux/rwsem.h>
 #include <linux/suspend.h>
 
+#include <soc/rockchip/rk3399_grf.h>
 #include <soc/rockchip/rockchip_sip.h>
 
 struct dram_timing {
@@ -69,8 +72,11 @@ struct rk3399_dmcfreq {
 	struct mutex lock;
 	struct dram_timing timing;
 	struct regulator *vdd_center;
+	struct regmap *regmap_pmu;
 	unsigned long rate, target_rate;
 	unsigned long volt, target_volt;
+	unsigned int odt_dis_freq;
+	int odt_pd_arg0, odt_pd_arg1;
 };
 
 static int rk3399_dmcfreq_target(struct device *dev, unsigned long *freq,
@@ -80,6 +86,8 @@ static int rk3399_dmcfreq_target(struct device *dev, unsigned long *freq,
 	struct dev_pm_opp *opp;
 	unsigned long old_clk_rate = dmcfreq->rate;
 	unsigned long target_volt, target_rate;
+	struct arm_smccc_res res;
+	bool odt_enable = false;
 	int err;
 
 	opp = devfreq_recommended_opp(dev, freq, flags);
@@ -95,6 +103,19 @@ static int rk3399_dmcfreq_target(struct device *dev, unsigned long *freq,
 
 	mutex_lock(&dmcfreq->lock);
 
+	if (target_rate >= dmcfreq->odt_dis_freq)
+		odt_enable = true;
+
+	/*
+	 * This makes a SMC call to the TF-A to set the DDR PD (power-down)
+	 * timings and to enable or disable the ODT (on-die termination)
+	 * resistors.
+	 */
+	arm_smccc_smc(ROCKCHIP_SIP_DRAM_FREQ, dmcfreq->odt_pd_arg0,
+		      dmcfreq->odt_pd_arg1,
+		      ROCKCHIP_SIP_CONFIG_DRAM_SET_ODT_PD,
+		      odt_enable, 0, 0, 0, &res);
+
 	/*
 	 * If frequency scaling from low to high, adjust voltage first.
 	 * If frequency scaling from high to low, adjust frequency first.
@@ -294,11 +315,13 @@ static int rk3399_dmcfreq_probe(struct platform_device *pdev)
 {
 	struct arm_smccc_res res;
 	struct device *dev = &pdev->dev;
-	struct device_node *np = pdev->dev.of_node;
+	struct device_node *np = pdev->dev.of_node, *node;
 	struct rk3399_dmcfreq *data;
 	int ret, index, size;
 	uint32_t *timing;
 	struct dev_pm_opp *opp;
+	u32 ddr_type;
+	u32 val;
 
 	data = devm_kzalloc(dev, sizeof(struct rk3399_dmcfreq), GFP_KERNEL);
 	if (!data)
@@ -354,10 +377,56 @@ static int rk3399_dmcfreq_probe(struct platform_device *pdev)
 		}
 	}
 
+	node = of_parse_phandle(np, "rockchip,pmu", 0);
+	if (node) {
+		data->regmap_pmu = syscon_node_to_regmap(node);
+		if (IS_ERR(data->regmap_pmu))
+			return PTR_ERR(data->regmap_pmu);
+	}
+
+	regmap_read(data->regmap_pmu, RK3399_PMUGRF_OS_REG2, &val);
+	ddr_type = (val >> RK3399_PMUGRF_DDRTYPE_SHIFT) &
+		    RK3399_PMUGRF_DDRTYPE_MASK;
+
+	switch (ddr_type) {
+	case RK3399_PMUGRF_DDRTYPE_DDR3:
+		data->odt_dis_freq = data->timing.ddr3_odt_dis_freq;
+		break;
+	case RK3399_PMUGRF_DDRTYPE_LPDDR3:
+		data->odt_dis_freq = data->timing.lpddr3_odt_dis_freq;
+		break;
+	case RK3399_PMUGRF_DDRTYPE_LPDDR4:
+		data->odt_dis_freq = data->timing.lpddr4_odt_dis_freq;
+		break;
+	default:
+		return -EINVAL;
+	};
+
 	arm_smccc_smc(ROCKCHIP_SIP_DRAM_FREQ, 0, 0,
 		      ROCKCHIP_SIP_CONFIG_DRAM_INIT,
 		      0, 0, 0, 0, &res);
 
+	/*
+	 * In TF-A there is a platform SIP call to set the PD (power-down)
+	 * timings and to enable or disable the ODT (on-die termination).
+	 * This call needs three arguments as follows:
+	 *
+	 * arg0:
+	 *     bit[0-7]   : sr_idle
+	 *     bit[8-15]  : sr_mc_gate_idle
+	 *     bit[16-31] : standby idle
+	 * arg1:
+	 *     bit[0-11]  : pd_idle
+	 *     bit[16-27] : srpd_lite_idle
+	 * arg2:
+	 *     bit[0]     : odt enable
+	 */
+	data->odt_pd_arg0 = (data->timing.sr_idle & 0xff) |
+			    ((data->timing.sr_mc_gate_idle & 0xff) << 8) |
+			    ((data->timing.standby_idle & 0xffff) << 16);
+	data->odt_pd_arg1 = (data->timing.pd_idle & 0xfff) |
+			    ((data->timing.srpd_lite_idle & 0xfff) << 16);
+
 	/*
 	 * We add a devfreq driver to our parent since it has a device tree node
 	 * with operating points.
diff --git a/include/soc/rockchip/rockchip_sip.h b/include/soc/rockchip/rockchip_sip.h
index 7e28092c4d3d..ad9482c56797 100644
--- a/include/soc/rockchip/rockchip_sip.h
+++ b/include/soc/rockchip/rockchip_sip.h
@@ -23,5 +23,6 @@
 #define ROCKCHIP_SIP_CONFIG_DRAM_GET_RATE	0x05
 #define ROCKCHIP_SIP_CONFIG_DRAM_CLR_IRQ	0x06
 #define ROCKCHIP_SIP_CONFIG_DRAM_SET_PARAM	0x07
+#define ROCKCHIP_SIP_CONFIG_DRAM_SET_ODT_PD	0x08
 
 #endif
-- 
2.21.0

[PATCH v3 3/5] devfreq: rk3399_dmc: Pass ODT and auto power down parameters to TF-A.

[Gaël PORTAY]

From: Enric Balletbo i Serra <enric.balletbo@collabora.com>

Trusted Firmware-A (TF-A) for rk3399 implements a SiP call to get the
on-die termination (ODT) and auto power down parameters from kernel,
this patch adds the functionality to do this. Also, if DDR clock
frequency is lower than the on-die termination (ODT) disable frequency
this driver should disable the DDR ODT.

Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
---

Changes in v3:
- [PATCH v2 3/5] Add Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>.
		 Remove comments.
		 Move pmu dt parsing after dt-parsing of timings to fix
		  data->odt_dis_freq value.

Changes in v2: None

Changes in v1:
- [RFC 3/10] Add an explanation for platform SIP calls.
- [RFC 3/10] Change if statement for a switch.
- [RFC 3/10] Rename ddr_flag to odt_enable to be more clear.

 drivers/devfreq/rk3399_dmc.c        | 71 ++++++++++++++++++++++++++++-
 include/soc/rockchip/rockchip_sip.h |  1 +
 2 files changed, 71 insertions(+), 1 deletion(-)

diff --git a/drivers/devfreq/rk3399_dmc.c b/drivers/devfreq/rk3399_dmc.c
index e795ad2b3f6b..daf19e121c99 100644
--- a/drivers/devfreq/rk3399_dmc.c
+++ b/drivers/devfreq/rk3399_dmc.c
@@ -18,14 +18,17 @@
 #include <linux/devfreq.h>
 #include <linux/devfreq-event.h>
 #include <linux/interrupt.h>
+#include <linux/mfd/syscon.h>
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/pm_opp.h>
+#include <linux/regmap.h>
 #include <linux/regulator/consumer.h>
 #include <linux/rwsem.h>
 #include <linux/suspend.h>
 
+#include <soc/rockchip/rk3399_grf.h>
 #include <soc/rockchip/rockchip_sip.h>
 
 struct dram_timing {
@@ -69,8 +72,11 @@ struct rk3399_dmcfreq {
 	struct mutex lock;
 	struct dram_timing timing;
 	struct regulator *vdd_center;
+	struct regmap *regmap_pmu;
 	unsigned long rate, target_rate;
 	unsigned long volt, target_volt;
+	unsigned int odt_dis_freq;
+	int odt_pd_arg0, odt_pd_arg1;
 };
 
 static int rk3399_dmcfreq_target(struct device *dev, unsigned long *freq,
@@ -80,6 +86,8 @@ static int rk3399_dmcfreq_target(struct device *dev, unsigned long *freq,
 	struct dev_pm_opp *opp;
 	unsigned long old_clk_rate = dmcfreq->rate;
 	unsigned long target_volt, target_rate;
+	struct arm_smccc_res res;
+	bool odt_enable = false;
 	int err;
 
 	opp = devfreq_recommended_opp(dev, freq, flags);
@@ -95,6 +103,19 @@ static int rk3399_dmcfreq_target(struct device *dev, unsigned long *freq,
 
 	mutex_lock(&dmcfreq->lock);
 
+	if (target_rate >= dmcfreq->odt_dis_freq)
+		odt_enable = true;
+
+	/*
+	 * This makes a SMC call to the TF-A to set the DDR PD (power-down)
+	 * timings and to enable or disable the ODT (on-die termination)
+	 * resistors.
+	 */
+	arm_smccc_smc(ROCKCHIP_SIP_DRAM_FREQ, dmcfreq->odt_pd_arg0,
+		      dmcfreq->odt_pd_arg1,
+		      ROCKCHIP_SIP_CONFIG_DRAM_SET_ODT_PD,
+		      odt_enable, 0, 0, 0, &res);
+
 	/*
 	 * If frequency scaling from low to high, adjust voltage first.
 	 * If frequency scaling from high to low, adjust frequency first.
@@ -294,11 +315,13 @@ static int rk3399_dmcfreq_probe(struct platform_device *pdev)
 {
 	struct arm_smccc_res res;
 	struct device *dev = &pdev->dev;
-	struct device_node *np = pdev->dev.of_node;
+	struct device_node *np = pdev->dev.of_node, *node;
 	struct rk3399_dmcfreq *data;
 	int ret, index, size;
 	uint32_t *timing;
 	struct dev_pm_opp *opp;
+	u32 ddr_type;
+	u32 val;
 
 	data = devm_kzalloc(dev, sizeof(struct rk3399_dmcfreq), GFP_KERNEL);
 	if (!data)
@@ -354,10 +377,56 @@ static int rk3399_dmcfreq_probe(struct platform_device *pdev)
 		}
 	}
 
+	node = of_parse_phandle(np, "rockchip,pmu", 0);
+	if (node) {
+		data->regmap_pmu = syscon_node_to_regmap(node);
+		if (IS_ERR(data->regmap_pmu))
+			return PTR_ERR(data->regmap_pmu);
+	}
+
+	regmap_read(data->regmap_pmu, RK3399_PMUGRF_OS_REG2, &val);
+	ddr_type = (val >> RK3399_PMUGRF_DDRTYPE_SHIFT) &
+		    RK3399_PMUGRF_DDRTYPE_MASK;
+
+	switch (ddr_type) {
+	case RK3399_PMUGRF_DDRTYPE_DDR3:
+		data->odt_dis_freq = data->timing.ddr3_odt_dis_freq;
+		break;
+	case RK3399_PMUGRF_DDRTYPE_LPDDR3:
+		data->odt_dis_freq = data->timing.lpddr3_odt_dis_freq;
+		break;
+	case RK3399_PMUGRF_DDRTYPE_LPDDR4:
+		data->odt_dis_freq = data->timing.lpddr4_odt_dis_freq;
+		break;
+	default:
+		return -EINVAL;
+	};
+
 	arm_smccc_smc(ROCKCHIP_SIP_DRAM_FREQ, 0, 0,
 		      ROCKCHIP_SIP_CONFIG_DRAM_INIT,
 		      0, 0, 0, 0, &res);
 
+	/*
+	 * In TF-A there is a platform SIP call to set the PD (power-down)
+	 * timings and to enable or disable the ODT (on-die termination).
+	 * This call needs three arguments as follows:
+	 *
+	 * arg0:
+	 *     bit[0-7]   : sr_idle
+	 *     bit[8-15]  : sr_mc_gate_idle
+	 *     bit[16-31] : standby idle
+	 * arg1:
+	 *     bit[0-11]  : pd_idle
+	 *     bit[16-27] : srpd_lite_idle
+	 * arg2:
+	 *     bit[0]     : odt enable
+	 */
+	data->odt_pd_arg0 = (data->timing.sr_idle & 0xff) |
+			    ((data->timing.sr_mc_gate_idle & 0xff) << 8) |
+			    ((data->timing.standby_idle & 0xffff) << 16);
+	data->odt_pd_arg1 = (data->timing.pd_idle & 0xfff) |
+			    ((data->timing.srpd_lite_idle & 0xfff) << 16);
+
 	/*
 	 * We add a devfreq driver to our parent since it has a device tree node
 	 * with operating points.
diff --git a/include/soc/rockchip/rockchip_sip.h b/include/soc/rockchip/rockchip_sip.h
index 7e28092c4d3d..ad9482c56797 100644
--- a/include/soc/rockchip/rockchip_sip.h
+++ b/include/soc/rockchip/rockchip_sip.h
@@ -23,5 +23,6 @@
 #define ROCKCHIP_SIP_CONFIG_DRAM_GET_RATE	0x05
 #define ROCKCHIP_SIP_CONFIG_DRAM_CLR_IRQ	0x06
 #define ROCKCHIP_SIP_CONFIG_DRAM_SET_PARAM	0x07
+#define ROCKCHIP_SIP_CONFIG_DRAM_SET_ODT_PD	0x08
 
 #endif
-- 
2.21.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 4/5] arm64: dts: rk3399: Add dfi and dmc nodes.

[Gaël PORTAY]

From: Lin Huang <hl@rock-chips.com>

These are required to support DDR DVFS on rk3399 platform. The patch also
introduces a new file with default DRAM settings.

Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
---

Changes in v3: None

Changes in v2:
- [PATCH 7/8] Reword the commit message to reflect the removal of
              rk3390-dram-default-timing.dts in v1.

Changes in v1:
- [RFC 8/10] Move rk3399-dram.h to dt-includes.
- [RFC 8/10] Put sdram default values under the dmc node.
- [RFC 8/10] Removed rk3399-dram-default-timing.dts

 .../boot/dts/rockchip/rk3399-op1-opp.dtsi     | 29 ++++++++
 arch/arm64/boot/dts/rockchip/rk3399.dtsi      | 49 +++++++++++++
 include/dt-bindings/power/rk3399-dram.h       | 73 +++++++++++++++++++
 3 files changed, 151 insertions(+)
 create mode 100644 include/dt-bindings/power/rk3399-dram.h

diff --git a/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi
index 69cc9b05baa5..c9e7032b01a8 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi
@@ -110,6 +110,31 @@
 			opp-microvolt = <1075000>;
 		};
 	};
+
+	dmc_opp_table: dmc_opp_table {
+		compatible = "operating-points-v2";
+
+		opp00 {
+			opp-hz = /bits/ 64 <200000000>;
+			opp-microvolt = <900000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <400000000>;
+			opp-microvolt = <900000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <666000000>;
+			opp-microvolt = <900000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <800000000>;
+			opp-microvolt = <900000>;
+		};
+		opp04 {
+			opp-hz = /bits/ 64 <928000000>;
+			opp-microvolt = <900000>;
+		};
+	};
 };
 
 &cpu_l0 {
@@ -139,3 +164,7 @@
 &gpu {
 	operating-points-v2 = <&gpu_opp_table>;
 };
+
+&dmc {
+	operating-points-v2 = <&dmc_opp_table>;
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
index db9d948c0b03..8fe86a3e7658 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
@@ -8,6 +8,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/power/rk3399-dram.h>
 #include <dt-bindings/power/rk3399-power.h>
 #include <dt-bindings/thermal/thermal.h>
 
@@ -1885,6 +1886,54 @@
 		status = "disabled";
 	};
 
+	dfi: dfi@ff630000 {
+		reg = <0x00 0xff630000 0x00 0x4000>;
+		compatible = "rockchip,rk3399-dfi";
+		rockchip,pmu = <&pmugrf>;
+		interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH 0>;
+		clocks = <&cru PCLK_DDR_MON>;
+		clock-names = "pclk_ddr_mon";
+		status = "disabled";
+	};
+
+	dmc: dmc {
+		compatible = "rockchip,rk3399-dmc";
+		rockchip,pmu = <&pmugrf>;
+		devfreq-events = <&dfi>;
+		clocks = <&cru SCLK_DDRC>;
+		clock-names = "dmc_clk";
+		status = "disabled";
+		rockchip,ddr3_speed_bin = <21>;
+		rockchip,pd_idle = <0x40>;
+		rockchip,sr_idle = <0x2>;
+		rockchip,sr_mc_gate_idle = <0x3>;
+		rockchip,srpd_lite_idle	= <0x4>;
+		rockchip,standby_idle = <0x2000>;
+		rockchip,dram_dll_dis_freq = <300000000>;
+		rockchip,phy_dll_dis_freq = <125000000>;
+		rockchip,auto_pd_dis_freq = <666000000>;
+		rockchip,ddr3_odt_dis_freq = <333000000>;
+		rockchip,ddr3_drv = <DDR3_DS_40ohm>;
+		rockchip,ddr3_odt = <DDR3_ODT_120ohm>;
+		rockchip,phy_ddr3_ca_drv = <PHY_DRV_ODT_40>;
+		rockchip,phy_ddr3_dq_drv = <PHY_DRV_ODT_40>;
+		rockchip,phy_ddr3_odt = <PHY_DRV_ODT_240>;
+		rockchip,lpddr3_odt_dis_freq = <333000000>;
+		rockchip,lpddr3_drv = <LP3_DS_34ohm>;
+		rockchip,lpddr3_odt = <LP3_ODT_240ohm>;
+		rockchip,phy_lpddr3_ca_drv = <PHY_DRV_ODT_40>;
+		rockchip,phy_lpddr3_dq_drv = <PHY_DRV_ODT_40>;
+		rockchip,phy_lpddr3_odt = <PHY_DRV_ODT_240>;
+		rockchip,lpddr4_odt_dis_freq = <333000000>;
+		rockchip,lpddr4_drv = <LP4_PDDS_60ohm>;
+		rockchip,lpddr4_dq_odt = <LP4_DQ_ODT_40ohm>;
+		rockchip,lpddr4_ca_odt = <LP4_CA_ODT_40ohm>;
+		rockchip,phy_lpddr4_ca_drv = <PHY_DRV_ODT_40>;
+		rockchip,phy_lpddr4_ck_cs_drv = <PHY_DRV_ODT_80>;
+		rockchip,phy_lpddr4_dq_drv = <PHY_DRV_ODT_80>;
+		rockchip,phy_lpddr4_odt = <PHY_DRV_ODT_60>;
+	};
+
 	pinctrl: pinctrl {
 		compatible = "rockchip,rk3399-pinctrl";
 		rockchip,grf = <&grf>;
diff --git a/include/dt-bindings/power/rk3399-dram.h b/include/dt-bindings/power/rk3399-dram.h
new file mode 100644
index 000000000000..4b3d4a79923b
--- /dev/null
+++ b/include/dt-bindings/power/rk3399-dram.h
@@ -0,0 +1,73 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR X11) */
+/*
+ * Copyright (c) 2016-2018, Fuzhou Rockchip Electronics Co., Ltd
+ *
+ * Author: Lin Huang <hl@rock-chips.com>
+ */
+
+#ifndef _DTS_DRAM_ROCKCHIP_RK3399_H
+#define _DTS_DRAM_ROCKCHIP_RK3399_H
+
+#define DDR3_DS_34ohm		34
+#define DDR3_DS_40ohm		40
+
+#define DDR3_ODT_DIS		0
+#define DDR3_ODT_40ohm		40
+#define DDR3_ODT_60ohm		60
+#define DDR3_ODT_120ohm		120
+
+#define LP2_DS_34ohm		34
+#define LP2_DS_40ohm		40
+#define LP2_DS_48ohm		48
+#define LP2_DS_60ohm		60
+#define LP2_DS_68_6ohm		68	/* optional */
+#define LP2_DS_80ohm		80
+#define LP2_DS_120ohm		120	/* optional */
+
+#define LP3_DS_34ohm		34
+#define LP3_DS_40ohm		40
+#define LP3_DS_48ohm		48
+#define LP3_DS_60ohm		60
+#define LP3_DS_80ohm		80
+#define LP3_DS_34D_40U		3440
+#define LP3_DS_40D_48U		4048
+#define LP3_DS_34D_48U		3448
+
+#define LP3_ODT_DIS		0
+#define LP3_ODT_60ohm		60
+#define LP3_ODT_120ohm		120
+#define LP3_ODT_240ohm		240
+
+#define LP4_PDDS_40ohm		40
+#define LP4_PDDS_48ohm		48
+#define LP4_PDDS_60ohm		60
+#define LP4_PDDS_80ohm		80
+#define LP4_PDDS_120ohm		120
+#define LP4_PDDS_240ohm		240
+
+#define LP4_DQ_ODT_40ohm	40
+#define LP4_DQ_ODT_48ohm	48
+#define LP4_DQ_ODT_60ohm	60
+#define LP4_DQ_ODT_80ohm	80
+#define LP4_DQ_ODT_120ohm	120
+#define LP4_DQ_ODT_240ohm	240
+#define LP4_DQ_ODT_DIS		0
+
+#define LP4_CA_ODT_40ohm	40
+#define LP4_CA_ODT_48ohm	48
+#define LP4_CA_ODT_60ohm	60
+#define LP4_CA_ODT_80ohm	80
+#define LP4_CA_ODT_120ohm	120
+#define LP4_CA_ODT_240ohm	240
+#define LP4_CA_ODT_DIS		0
+
+#define PHY_DRV_ODT_Hi_Z	0
+#define PHY_DRV_ODT_240		240
+#define PHY_DRV_ODT_120		120
+#define PHY_DRV_ODT_80		80
+#define PHY_DRV_ODT_60		60
+#define PHY_DRV_ODT_48		48
+#define PHY_DRV_ODT_40		40
+#define PHY_DRV_ODT_34_3	34
+
+#endif /* _DTS_DRAM_ROCKCHIP_RK3399_H */
-- 
2.21.0

[PATCH v3 4/5] arm64: dts: rk3399: Add dfi and dmc nodes.

[Gaël PORTAY]

From: Lin Huang <hl@rock-chips.com>

These are required to support DDR DVFS on rk3399 platform. The patch also
introduces a new file with default DRAM settings.

Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
---

Changes in v3: None

Changes in v2:
- [PATCH 7/8] Reword the commit message to reflect the removal of
              rk3390-dram-default-timing.dts in v1.

Changes in v1:
- [RFC 8/10] Move rk3399-dram.h to dt-includes.
- [RFC 8/10] Put sdram default values under the dmc node.
- [RFC 8/10] Removed rk3399-dram-default-timing.dts

 .../boot/dts/rockchip/rk3399-op1-opp.dtsi     | 29 ++++++++
 arch/arm64/boot/dts/rockchip/rk3399.dtsi      | 49 +++++++++++++
 include/dt-bindings/power/rk3399-dram.h       | 73 +++++++++++++++++++
 3 files changed, 151 insertions(+)
 create mode 100644 include/dt-bindings/power/rk3399-dram.h

diff --git a/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi
index 69cc9b05baa5..c9e7032b01a8 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi
@@ -110,6 +110,31 @@
 			opp-microvolt = <1075000>;
 		};
 	};
+
+	dmc_opp_table: dmc_opp_table {
+		compatible = "operating-points-v2";
+
+		opp00 {
+			opp-hz = /bits/ 64 <200000000>;
+			opp-microvolt = <900000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <400000000>;
+			opp-microvolt = <900000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <666000000>;
+			opp-microvolt = <900000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <800000000>;
+			opp-microvolt = <900000>;
+		};
+		opp04 {
+			opp-hz = /bits/ 64 <928000000>;
+			opp-microvolt = <900000>;
+		};
+	};
 };
 
 &cpu_l0 {
@@ -139,3 +164,7 @@
 &gpu {
 	operating-points-v2 = <&gpu_opp_table>;
 };
+
+&dmc {
+	operating-points-v2 = <&dmc_opp_table>;
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
index db9d948c0b03..8fe86a3e7658 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
@@ -8,6 +8,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/power/rk3399-dram.h>
 #include <dt-bindings/power/rk3399-power.h>
 #include <dt-bindings/thermal/thermal.h>
 
@@ -1885,6 +1886,54 @@
 		status = "disabled";
 	};
 
+	dfi: dfi@ff630000 {
+		reg = <0x00 0xff630000 0x00 0x4000>;
+		compatible = "rockchip,rk3399-dfi";
+		rockchip,pmu = <&pmugrf>;
+		interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH 0>;
+		clocks = <&cru PCLK_DDR_MON>;
+		clock-names = "pclk_ddr_mon";
+		status = "disabled";
+	};
+
+	dmc: dmc {
+		compatible = "rockchip,rk3399-dmc";
+		rockchip,pmu = <&pmugrf>;
+		devfreq-events = <&dfi>;
+		clocks = <&cru SCLK_DDRC>;
+		clock-names = "dmc_clk";
+		status = "disabled";
+		rockchip,ddr3_speed_bin = <21>;
+		rockchip,pd_idle = <0x40>;
+		rockchip,sr_idle = <0x2>;
+		rockchip,sr_mc_gate_idle = <0x3>;
+		rockchip,srpd_lite_idle	= <0x4>;
+		rockchip,standby_idle = <0x2000>;
+		rockchip,dram_dll_dis_freq = <300000000>;
+		rockchip,phy_dll_dis_freq = <125000000>;
+		rockchip,auto_pd_dis_freq = <666000000>;
+		rockchip,ddr3_odt_dis_freq = <333000000>;
+		rockchip,ddr3_drv = <DDR3_DS_40ohm>;
+		rockchip,ddr3_odt = <DDR3_ODT_120ohm>;
+		rockchip,phy_ddr3_ca_drv = <PHY_DRV_ODT_40>;
+		rockchip,phy_ddr3_dq_drv = <PHY_DRV_ODT_40>;
+		rockchip,phy_ddr3_odt = <PHY_DRV_ODT_240>;
+		rockchip,lpddr3_odt_dis_freq = <333000000>;
+		rockchip,lpddr3_drv = <LP3_DS_34ohm>;
+		rockchip,lpddr3_odt = <LP3_ODT_240ohm>;
+		rockchip,phy_lpddr3_ca_drv = <PHY_DRV_ODT_40>;
+		rockchip,phy_lpddr3_dq_drv = <PHY_DRV_ODT_40>;
+		rockchip,phy_lpddr3_odt = <PHY_DRV_ODT_240>;
+		rockchip,lpddr4_odt_dis_freq = <333000000>;
+		rockchip,lpddr4_drv = <LP4_PDDS_60ohm>;
+		rockchip,lpddr4_dq_odt = <LP4_DQ_ODT_40ohm>;
+		rockchip,lpddr4_ca_odt = <LP4_CA_ODT_40ohm>;
+		rockchip,phy_lpddr4_ca_drv = <PHY_DRV_ODT_40>;
+		rockchip,phy_lpddr4_ck_cs_drv = <PHY_DRV_ODT_80>;
+		rockchip,phy_lpddr4_dq_drv = <PHY_DRV_ODT_80>;
+		rockchip,phy_lpddr4_odt = <PHY_DRV_ODT_60>;
+	};
+
 	pinctrl: pinctrl {
 		compatible = "rockchip,rk3399-pinctrl";
 		rockchip,grf = <&grf>;
diff --git a/include/dt-bindings/power/rk3399-dram.h b/include/dt-bindings/power/rk3399-dram.h
new file mode 100644
index 000000000000..4b3d4a79923b
--- /dev/null
+++ b/include/dt-bindings/power/rk3399-dram.h
@@ -0,0 +1,73 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR X11) */
+/*
+ * Copyright (c) 2016-2018, Fuzhou Rockchip Electronics Co., Ltd
+ *
+ * Author: Lin Huang <hl@rock-chips.com>
+ */
+
+#ifndef _DTS_DRAM_ROCKCHIP_RK3399_H
+#define _DTS_DRAM_ROCKCHIP_RK3399_H
+
+#define DDR3_DS_34ohm		34
+#define DDR3_DS_40ohm		40
+
+#define DDR3_ODT_DIS		0
+#define DDR3_ODT_40ohm		40
+#define DDR3_ODT_60ohm		60
+#define DDR3_ODT_120ohm		120
+
+#define LP2_DS_34ohm		34
+#define LP2_DS_40ohm		40
+#define LP2_DS_48ohm		48
+#define LP2_DS_60ohm		60
+#define LP2_DS_68_6ohm		68	/* optional */
+#define LP2_DS_80ohm		80
+#define LP2_DS_120ohm		120	/* optional */
+
+#define LP3_DS_34ohm		34
+#define LP3_DS_40ohm		40
+#define LP3_DS_48ohm		48
+#define LP3_DS_60ohm		60
+#define LP3_DS_80ohm		80
+#define LP3_DS_34D_40U		3440
+#define LP3_DS_40D_48U		4048
+#define LP3_DS_34D_48U		3448
+
+#define LP3_ODT_DIS		0
+#define LP3_ODT_60ohm		60
+#define LP3_ODT_120ohm		120
+#define LP3_ODT_240ohm		240
+
+#define LP4_PDDS_40ohm		40
+#define LP4_PDDS_48ohm		48
+#define LP4_PDDS_60ohm		60
+#define LP4_PDDS_80ohm		80
+#define LP4_PDDS_120ohm		120
+#define LP4_PDDS_240ohm		240
+
+#define LP4_DQ_ODT_40ohm	40
+#define LP4_DQ_ODT_48ohm	48
+#define LP4_DQ_ODT_60ohm	60
+#define LP4_DQ_ODT_80ohm	80
+#define LP4_DQ_ODT_120ohm	120
+#define LP4_DQ_ODT_240ohm	240
+#define LP4_DQ_ODT_DIS		0
+
+#define LP4_CA_ODT_40ohm	40
+#define LP4_CA_ODT_48ohm	48
+#define LP4_CA_ODT_60ohm	60
+#define LP4_CA_ODT_80ohm	80
+#define LP4_CA_ODT_120ohm	120
+#define LP4_CA_ODT_240ohm	240
+#define LP4_CA_ODT_DIS		0
+
+#define PHY_DRV_ODT_Hi_Z	0
+#define PHY_DRV_ODT_240		240
+#define PHY_DRV_ODT_120		120
+#define PHY_DRV_ODT_80		80
+#define PHY_DRV_ODT_60		60
+#define PHY_DRV_ODT_48		48
+#define PHY_DRV_ODT_40		40
+#define PHY_DRV_ODT_34_3	34
+
+#endif /* _DTS_DRAM_ROCKCHIP_RK3399_H */
-- 
2.21.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 5/5] arm64: dts: rockchip: Enable dmc and dfi nodes on gru.

[Gaël PORTAY]

From: Lin Huang <hl@rock-chips.com>

Enable the DMC (Dynamic Memory Controller) and the DFI (DDR PHY Interface)
nodes on gru/kevin boards so we can support DDR DVFS.

Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
---

Changes in v3:
- [PATCH v2 5/5] Remove display_subsystem nodes.

Changes in v2:
- [PATCH 8/8] Move center-supply attribute of dmc node in file
              rk3399-gru-chromebook.dtsi (where ppvar_centerlogic is
	      defined).

Changes in v1: None

 .../boot/dts/rockchip/rk3399-gru-chromebook.dtsi |  4 ++++
 arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi     | 16 ++++++++++++++++
 2 files changed, 20 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
index 931640e9aed4..cfb81356c61e 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
@@ -400,3 +400,7 @@ ap_i2c_tp: &i2c5 {
 		rockchip,pins = <0 8 RK_FUNC_GPIO &pcfg_pull_none>;
 	};
 };
+
+&dmc {
+	center-supply = <&ppvar_centerlogic>;
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
index da03fa9c5662..1bde7ad3b980 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
@@ -289,6 +289,12 @@
 	status = "okay";
 };
 
+&dmc_opp_table {
+	opp04 {
+		opp-suspend;
+	};
+};
+
 /*
  * Set some suspend operating points to avoid OVP in suspend
  *
@@ -489,6 +495,16 @@ ap_i2c_audio: &i2c8 {
 	status = "okay";
 };
 
+&dfi {
+	status = "okay";
+};
+
+&dmc {
+	status = "okay";
+	upthreshold = <25>;
+	downdifferential = <15>;
+};
+
 &sdhci {
 	/*
 	 * Signal integrity isn't great at 200 MHz and 150 MHz (DDR) gives the
-- 
2.21.0

[PATCH v3 5/5] arm64: dts: rockchip: Enable dmc and dfi nodes on gru.

[Gaël PORTAY]

From: Lin Huang <hl@rock-chips.com>

Enable the DMC (Dynamic Memory Controller) and the DFI (DDR PHY Interface)
nodes on gru/kevin boards so we can support DDR DVFS.

Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
---

Changes in v3:
- [PATCH v2 5/5] Remove display_subsystem nodes.

Changes in v2:
- [PATCH 8/8] Move center-supply attribute of dmc node in file
              rk3399-gru-chromebook.dtsi (where ppvar_centerlogic is
	      defined).

Changes in v1: None

 .../boot/dts/rockchip/rk3399-gru-chromebook.dtsi |  4 ++++
 arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi     | 16 ++++++++++++++++
 2 files changed, 20 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
index 931640e9aed4..cfb81356c61e 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
@@ -400,3 +400,7 @@ ap_i2c_tp: &i2c5 {
 		rockchip,pins = <0 8 RK_FUNC_GPIO &pcfg_pull_none>;
 	};
 };
+
+&dmc {
+	center-supply = <&ppvar_centerlogic>;
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
index da03fa9c5662..1bde7ad3b980 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
@@ -289,6 +289,12 @@
 	status = "okay";
 };
 
+&dmc_opp_table {
+	opp04 {
+		opp-suspend;
+	};
+};
+
 /*
  * Set some suspend operating points to avoid OVP in suspend
  *
@@ -489,6 +495,16 @@ ap_i2c_audio: &i2c8 {
 	status = "okay";
 };
 
+&dfi {
+	status = "okay";
+};
+
+&dmc {
+	status = "okay";
+	upthreshold = <25>;
+	downdifferential = <15>;
+};
+
 &sdhci {
 	/*
 	 * Signal integrity isn't great at 200 MHz and 150 MHz (DDR) gives the
-- 
2.21.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

RE: [PATCH v3 1/5] devfreq: rockchip-dfi: Move GRF definitions to a common place.

[MyungJoo Ham]

>From: Enric Balletbo i Serra <enric.balletbo@collabora.com>
>
>Some rk3399 GRF (Generic Register Files) definitions can be used for
>different drivers. Move these definitions to a common include so we
>don't need to duplicate these definitions.
>
>Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
>Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
>Signed-off-by: Gael PORTAY <gael.portay@collabora.com>
>---
>
>Changes in v3:
>- [PATCH v2 1/5] Add Signed-off-by: Gael PORTAY <gael.portay@collabora.com>.
>
>Changes in v2:
>- [PATCH 1/8] Really add Acked-by: Chanwoo Choi <cw00.choi@samsung.com>.
>
>Changes in v1:
>- [RFC 1/10] Add Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
>- [RFC 1/10] s/Generic/General/ (Robin Murphy)
>- [RFC 4/10] Removed from the series. I did not found a use case where not holding the mutex causes the issue.
>- [RFC 7/10] Removed from the series. I did not found a use case where this matters.
>
> drivers/devfreq/event/rockchip-dfi.c | 23 +++++++----------------
> include/soc/rockchip/rk3399_grf.h    | 21 +++++++++++++++++++++
> 2 files changed, 28 insertions(+), 16 deletions(-)
> create mode 100644 include/soc/rockchip/rk3399_grf.h
>

Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>

RE: [PATCH v3 1/5] devfreq: rockchip-dfi: Move GRF definitions to a common place.

[MyungJoo Ham]

>From: Enric Balletbo i Serra <enric.balletbo@collabora.com>
>
>Some rk3399 GRF (Generic Register Files) definitions can be used for
>different drivers. Move these definitions to a common include so we
>don't need to duplicate these definitions.
>
>Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
>Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
>Signed-off-by: Gael PORTAY <gael.portay@collabora.com>
>---
>
>Changes in v3:
>- [PATCH v2 1/5] Add Signed-off-by: Gael PORTAY <gael.portay@collabora.com>.
>
>Changes in v2:
>- [PATCH 1/8] Really add Acked-by: Chanwoo Choi <cw00.choi@samsung.com>.
>
>Changes in v1:
>- [RFC 1/10] Add Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
>- [RFC 1/10] s/Generic/General/ (Robin Murphy)
>- [RFC 4/10] Removed from the series. I did not found a use case where not holding the mutex causes the issue.
>- [RFC 7/10] Removed from the series. I did not found a use case where this matters.
>
> drivers/devfreq/event/rockchip-dfi.c | 23 +++++++----------------
> include/soc/rockchip/rk3399_grf.h    | 21 +++++++++++++++++++++
> 2 files changed, 28 insertions(+), 16 deletions(-)
> create mode 100644 include/soc/rockchip/rk3399_grf.h
>

Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>

RE: [PATCH v3 1/5] devfreq: rockchip-dfi: Move GRF definitions to a common place.

[MyungJoo Ham]

>From: Enric Balletbo i Serra <enric.balletbo@collabora.com>
>
>Some rk3399 GRF (Generic Register Files) definitions can be used for
>different drivers. Move these definitions to a common include so we
>don't need to duplicate these definitions.
>
>Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
>Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
>Signed-off-by: Gael PORTAY <gael.portay@collabora.com>
>---
>
>Changes in v3:
>- [PATCH v2 1/5] Add Signed-off-by: Gael PORTAY <gael.portay@collabora.com>.
>
>Changes in v2:
>- [PATCH 1/8] Really add Acked-by: Chanwoo Choi <cw00.choi@samsung.com>.
>
>Changes in v1:
>- [RFC 1/10] Add Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
>- [RFC 1/10] s/Generic/General/ (Robin Murphy)
>- [RFC 4/10] Removed from the series. I did not found a use case where not holding the mutex causes the issue.
>- [RFC 7/10] Removed from the series. I did not found a use case where this matters.
>
> drivers/devfreq/event/rockchip-dfi.c | 23 +++++++----------------
> include/soc/rockchip/rk3399_grf.h    | 21 +++++++++++++++++++++
> 2 files changed, 28 insertions(+), 16 deletions(-)
> create mode 100644 include/soc/rockchip/rk3399_grf.h
>

Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>



_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

RE: [PATCH v3 2/5] dt-bindings: devfreq: rk3399_dmc: Add rockchip,pmu phandle.

[MyungJoo Ham]

>From: Enric Balletbo i Serra <enric.balletbo@collabora.com>
>
>The Rockchip DMC (Dynamic Memory Interface) needs to access to the PMU
>general register files to know the DRAM type, so add a phandle to the
>syscon that manages these registers.
>
>Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
>Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
>Acked-by: Rob Herring <robh@kernel.org>
>Signed-off-by: Gael PORTAY <gael.portay@collabora.com>
>---
>
>Changes in v3:
>- [PATCH v2 2/5] Add Signed-off-by: Gael PORTAY <gael.portay@collabora.com>.
>
>Changes in v2: None
>
>Changes in v1:
>- [RFC 2/10] Add reviewed and acked tags from Chanwoo Choi and Rob Herring
>
> Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt | 2 ++
> 1 file changed, 2 insertions(+)

Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>

RE: [PATCH v3 2/5] dt-bindings: devfreq: rk3399_dmc: Add rockchip,pmu phandle.

[MyungJoo Ham]

>From: Enric Balletbo i Serra <enric.balletbo@collabora.com>
>
>The Rockchip DMC (Dynamic Memory Interface) needs to access to the PMU
>general register files to know the DRAM type, so add a phandle to the
>syscon that manages these registers.
>
>Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
>Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
>Acked-by: Rob Herring <robh@kernel.org>
>Signed-off-by: Gael PORTAY <gael.portay@collabora.com>
>---
>
>Changes in v3:
>- [PATCH v2 2/5] Add Signed-off-by: Gael PORTAY <gael.portay@collabora.com>.
>
>Changes in v2: None
>
>Changes in v1:
>- [RFC 2/10] Add reviewed and acked tags from Chanwoo Choi and Rob Herring
>
> Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt | 2 ++
> 1 file changed, 2 insertions(+)

Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>

RE: [PATCH v3 2/5] dt-bindings: devfreq: rk3399_dmc: Add rockchip,pmu phandle.

[MyungJoo Ham]

>From: Enric Balletbo i Serra <enric.balletbo@collabora.com>
>
>The Rockchip DMC (Dynamic Memory Interface) needs to access to the PMU
>general register files to know the DRAM type, so add a phandle to the
>syscon that manages these registers.
>
>Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
>Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
>Acked-by: Rob Herring <robh@kernel.org>
>Signed-off-by: Gael PORTAY <gael.portay@collabora.com>
>---
>
>Changes in v3:
>- [PATCH v2 2/5] Add Signed-off-by: Gael PORTAY <gael.portay@collabora.com>.
>
>Changes in v2: None
>
>Changes in v1:
>- [RFC 2/10] Add reviewed and acked tags from Chanwoo Choi and Rob Herring
>
> Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt | 2 ++
> 1 file changed, 2 insertions(+)

Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

RE: [PATCH v3 3/5] devfreq: rk3399_dmc: Pass ODT and auto power down parameters to TF-A.

[MyungJoo Ham]

>From: Enric Balletbo i Serra <enric.balletbo@collabora.com>
>
>Trusted Firmware-A (TF-A) for rk3399 implements a SiP call to get the
>on-die termination (ODT) and auto power down parameters from kernel,
>this patch adds the functionality to do this. Also, if DDR clock
>frequency is lower than the on-die termination (ODT) disable frequency
>this driver should disable the DDR ODT.
>
>Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
>Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
>Signed-off-by: Gael PORTAY <gael.portay@collabora.com>

Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>


Cheers!
MyungJoo

>---
>
>Changes in v3:
>- [PATCH v2 3/5] Add Signed-off-by: Gael PORTAY <gael.portay@collabora.com>.
>		 Remove comments.
>		 Move pmu dt parsing after dt-parsing of timings to fix
>		  data->odt_dis_freq value.
>
>Changes in v2: None
>
>Changes in v1:
>- [RFC 3/10] Add an explanation for platform SIP calls.
>- [RFC 3/10] Change if statement for a switch.
>- [RFC 3/10] Rename ddr_flag to odt_enable to be more clear.
>
> drivers/devfreq/rk3399_dmc.c        | 71 ++++++++++++++++++++++++++++-
> include/soc/rockchip/rockchip_sip.h |  1 +
> 2 files changed, 71 insertions(+), 1 deletion(-)

RE: [PATCH v3 3/5] devfreq: rk3399_dmc: Pass ODT and auto power down parameters to TF-A.

[MyungJoo Ham]

>From: Enric Balletbo i Serra <enric.balletbo@collabora.com>
>
>Trusted Firmware-A (TF-A) for rk3399 implements a SiP call to get the
>on-die termination (ODT) and auto power down parameters from kernel,
>this patch adds the functionality to do this. Also, if DDR clock
>frequency is lower than the on-die termination (ODT) disable frequency
>this driver should disable the DDR ODT.
>
>Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
>Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
>Signed-off-by: Gael PORTAY <gael.portay@collabora.com>

Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>


Cheers!
MyungJoo

>---
>
>Changes in v3:
>- [PATCH v2 3/5] Add Signed-off-by: Gael PORTAY <gael.portay@collabora.com>.
>		 Remove comments.
>		 Move pmu dt parsing after dt-parsing of timings to fix
>		  data->odt_dis_freq value.
>
>Changes in v2: None
>
>Changes in v1:
>- [RFC 3/10] Add an explanation for platform SIP calls.
>- [RFC 3/10] Change if statement for a switch.
>- [RFC 3/10] Rename ddr_flag to odt_enable to be more clear.
>
> drivers/devfreq/rk3399_dmc.c        | 71 ++++++++++++++++++++++++++++-
> include/soc/rockchip/rockchip_sip.h |  1 +
> 2 files changed, 71 insertions(+), 1 deletion(-)

RE: [PATCH v3 3/5] devfreq: rk3399_dmc: Pass ODT and auto power down parameters to TF-A.

[MyungJoo Ham]

>From: Enric Balletbo i Serra <enric.balletbo@collabora.com>
>
>Trusted Firmware-A (TF-A) for rk3399 implements a SiP call to get the
>on-die termination (ODT) and auto power down parameters from kernel,
>this patch adds the functionality to do this. Also, if DDR clock
>frequency is lower than the on-die termination (ODT) disable frequency
>this driver should disable the DDR ODT.
>
>Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
>Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
>Signed-off-by: Gael PORTAY <gael.portay@collabora.com>

Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>


Cheers!
MyungJoo

>---
>
>Changes in v3:
>- [PATCH v2 3/5] Add Signed-off-by: Gael PORTAY <gael.portay@collabora.com>.
>		 Remove comments.
>		 Move pmu dt parsing after dt-parsing of timings to fix
>		  data->odt_dis_freq value.
>
>Changes in v2: None
>
>Changes in v1:
>- [RFC 3/10] Add an explanation for platform SIP calls.
>- [RFC 3/10] Change if statement for a switch.
>- [RFC 3/10] Rename ddr_flag to odt_enable to be more clear.
>
> drivers/devfreq/rk3399_dmc.c        | 71 ++++++++++++++++++++++++++++-
> include/soc/rockchip/rockchip_sip.h |  1 +
> 2 files changed, 71 insertions(+), 1 deletion(-)

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 4/5] arm64: dts: rk3399: Add dfi and dmc nodes.

[Rob Herring]

On Thu, Mar 21, 2019 at 07:14:39PM -0400, Gaël PORTAY wrote:
> From: Lin Huang <hl@rock-chips.com>
> 
> These are required to support DDR DVFS on rk3399 platform. The patch also
> introduces a new file with default DRAM settings.
> 
> Signed-off-by: Lin Huang <hl@rock-chips.com>
> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
> Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
> ---
> 
> Changes in v3: None
> 
> Changes in v2:
> - [PATCH 7/8] Reword the commit message to reflect the removal of
>               rk3390-dram-default-timing.dts in v1.
> 
> Changes in v1:
> - [RFC 8/10] Move rk3399-dram.h to dt-includes.
> - [RFC 8/10] Put sdram default values under the dmc node.
> - [RFC 8/10] Removed rk3399-dram-default-timing.dts
> 
>  .../boot/dts/rockchip/rk3399-op1-opp.dtsi     | 29 ++++++++
>  arch/arm64/boot/dts/rockchip/rk3399.dtsi      | 49 +++++++++++++
>  include/dt-bindings/power/rk3399-dram.h       | 73 +++++++++++++++++++
>  3 files changed, 151 insertions(+)
>  create mode 100644 include/dt-bindings/power/rk3399-dram.h
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi
> index 69cc9b05baa5..c9e7032b01a8 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi
> @@ -110,6 +110,31 @@
>  			opp-microvolt = <1075000>;
>  		};
>  	};
> +
> +	dmc_opp_table: dmc_opp_table {
> +		compatible = "operating-points-v2";
> +
> +		opp00 {
> +			opp-hz = /bits/ 64 <200000000>;
> +			opp-microvolt = <900000>;
> +		};
> +		opp01 {
> +			opp-hz = /bits/ 64 <400000000>;
> +			opp-microvolt = <900000>;
> +		};
> +		opp02 {
> +			opp-hz = /bits/ 64 <666000000>;
> +			opp-microvolt = <900000>;
> +		};
> +		opp03 {
> +			opp-hz = /bits/ 64 <800000000>;
> +			opp-microvolt = <900000>;
> +		};
> +		opp04 {
> +			opp-hz = /bits/ 64 <928000000>;
> +			opp-microvolt = <900000>;
> +		};
> +	};
>  };
>  
>  &cpu_l0 {
> @@ -139,3 +164,7 @@
>  &gpu {
>  	operating-points-v2 = <&gpu_opp_table>;
>  };
> +
> +&dmc {
> +	operating-points-v2 = <&dmc_opp_table>;
> +};
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
> index db9d948c0b03..8fe86a3e7658 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
> @@ -8,6 +8,7 @@
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
>  #include <dt-bindings/interrupt-controller/irq.h>
>  #include <dt-bindings/pinctrl/rockchip.h>
> +#include <dt-bindings/power/rk3399-dram.h>
>  #include <dt-bindings/power/rk3399-power.h>
>  #include <dt-bindings/thermal/thermal.h>
>  
> @@ -1885,6 +1886,54 @@
>  		status = "disabled";
>  	};
>  
> +	dfi: dfi@ff630000 {
> +		reg = <0x00 0xff630000 0x00 0x4000>;
> +		compatible = "rockchip,rk3399-dfi";
> +		rockchip,pmu = <&pmugrf>;
> +		interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH 0>;
> +		clocks = <&cru PCLK_DDR_MON>;
> +		clock-names = "pclk_ddr_mon";
> +		status = "disabled";
> +	};
> +
> +	dmc: dmc {
> +		compatible = "rockchip,rk3399-dmc";
> +		rockchip,pmu = <&pmugrf>;
> +		devfreq-events = <&dfi>;
> +		clocks = <&cru SCLK_DDRC>;
> +		clock-names = "dmc_clk";
> +		status = "disabled";
> +		rockchip,ddr3_speed_bin = <21>;
> +		rockchip,pd_idle = <0x40>;
> +		rockchip,sr_idle = <0x2>;
> +		rockchip,sr_mc_gate_idle = <0x3>;
> +		rockchip,srpd_lite_idle	= <0x4>;
> +		rockchip,standby_idle = <0x2000>;
> +		rockchip,dram_dll_dis_freq = <300000000>;
> +		rockchip,phy_dll_dis_freq = <125000000>;
> +		rockchip,auto_pd_dis_freq = <666000000>;
> +		rockchip,ddr3_odt_dis_freq = <333000000>;
> +		rockchip,ddr3_drv = <DDR3_DS_40ohm>;
> +		rockchip,ddr3_odt = <DDR3_ODT_120ohm>;
> +		rockchip,phy_ddr3_ca_drv = <PHY_DRV_ODT_40>;
> +		rockchip,phy_ddr3_dq_drv = <PHY_DRV_ODT_40>;
> +		rockchip,phy_ddr3_odt = <PHY_DRV_ODT_240>;
> +		rockchip,lpddr3_odt_dis_freq = <333000000>;
> +		rockchip,lpddr3_drv = <LP3_DS_34ohm>;
> +		rockchip,lpddr3_odt = <LP3_ODT_240ohm>;
> +		rockchip,phy_lpddr3_ca_drv = <PHY_DRV_ODT_40>;
> +		rockchip,phy_lpddr3_dq_drv = <PHY_DRV_ODT_40>;
> +		rockchip,phy_lpddr3_odt = <PHY_DRV_ODT_240>;
> +		rockchip,lpddr4_odt_dis_freq = <333000000>;
> +		rockchip,lpddr4_drv = <LP4_PDDS_60ohm>;
> +		rockchip,lpddr4_dq_odt = <LP4_DQ_ODT_40ohm>;
> +		rockchip,lpddr4_ca_odt = <LP4_CA_ODT_40ohm>;
> +		rockchip,phy_lpddr4_ca_drv = <PHY_DRV_ODT_40>;
> +		rockchip,phy_lpddr4_ck_cs_drv = <PHY_DRV_ODT_80>;
> +		rockchip,phy_lpddr4_dq_drv = <PHY_DRV_ODT_80>;
> +		rockchip,phy_lpddr4_odt = <PHY_DRV_ODT_60>;

These settings aren't board specific?

Rob

Re: [PATCH v3 4/5] arm64: dts: rk3399: Add dfi and dmc nodes.

[Rob Herring]

On Thu, Mar 21, 2019 at 07:14:39PM -0400, Gaël PORTAY wrote:
> From: Lin Huang <hl@rock-chips.com>
> 
> These are required to support DDR DVFS on rk3399 platform. The patch also
> introduces a new file with default DRAM settings.
> 
> Signed-off-by: Lin Huang <hl@rock-chips.com>
> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
> Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
> ---
> 
> Changes in v3: None
> 
> Changes in v2:
> - [PATCH 7/8] Reword the commit message to reflect the removal of
>               rk3390-dram-default-timing.dts in v1.
> 
> Changes in v1:
> - [RFC 8/10] Move rk3399-dram.h to dt-includes.
> - [RFC 8/10] Put sdram default values under the dmc node.
> - [RFC 8/10] Removed rk3399-dram-default-timing.dts
> 
>  .../boot/dts/rockchip/rk3399-op1-opp.dtsi     | 29 ++++++++
>  arch/arm64/boot/dts/rockchip/rk3399.dtsi      | 49 +++++++++++++
>  include/dt-bindings/power/rk3399-dram.h       | 73 +++++++++++++++++++
>  3 files changed, 151 insertions(+)
>  create mode 100644 include/dt-bindings/power/rk3399-dram.h
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi
> index 69cc9b05baa5..c9e7032b01a8 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi
> @@ -110,6 +110,31 @@
>  			opp-microvolt = <1075000>;
>  		};
>  	};
> +
> +	dmc_opp_table: dmc_opp_table {
> +		compatible = "operating-points-v2";
> +
> +		opp00 {
> +			opp-hz = /bits/ 64 <200000000>;
> +			opp-microvolt = <900000>;
> +		};
> +		opp01 {
> +			opp-hz = /bits/ 64 <400000000>;
> +			opp-microvolt = <900000>;
> +		};
> +		opp02 {
> +			opp-hz = /bits/ 64 <666000000>;
> +			opp-microvolt = <900000>;
> +		};
> +		opp03 {
> +			opp-hz = /bits/ 64 <800000000>;
> +			opp-microvolt = <900000>;
> +		};
> +		opp04 {
> +			opp-hz = /bits/ 64 <928000000>;
> +			opp-microvolt = <900000>;
> +		};
> +	};
>  };
>  
>  &cpu_l0 {
> @@ -139,3 +164,7 @@
>  &gpu {
>  	operating-points-v2 = <&gpu_opp_table>;
>  };
> +
> +&dmc {
> +	operating-points-v2 = <&dmc_opp_table>;
> +};
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
> index db9d948c0b03..8fe86a3e7658 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
> @@ -8,6 +8,7 @@
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
>  #include <dt-bindings/interrupt-controller/irq.h>
>  #include <dt-bindings/pinctrl/rockchip.h>
> +#include <dt-bindings/power/rk3399-dram.h>
>  #include <dt-bindings/power/rk3399-power.h>
>  #include <dt-bindings/thermal/thermal.h>
>  
> @@ -1885,6 +1886,54 @@
>  		status = "disabled";
>  	};
>  
> +	dfi: dfi@ff630000 {
> +		reg = <0x00 0xff630000 0x00 0x4000>;
> +		compatible = "rockchip,rk3399-dfi";
> +		rockchip,pmu = <&pmugrf>;
> +		interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH 0>;
> +		clocks = <&cru PCLK_DDR_MON>;
> +		clock-names = "pclk_ddr_mon";
> +		status = "disabled";
> +	};
> +
> +	dmc: dmc {
> +		compatible = "rockchip,rk3399-dmc";
> +		rockchip,pmu = <&pmugrf>;
> +		devfreq-events = <&dfi>;
> +		clocks = <&cru SCLK_DDRC>;
> +		clock-names = "dmc_clk";
> +		status = "disabled";
> +		rockchip,ddr3_speed_bin = <21>;
> +		rockchip,pd_idle = <0x40>;
> +		rockchip,sr_idle = <0x2>;
> +		rockchip,sr_mc_gate_idle = <0x3>;
> +		rockchip,srpd_lite_idle	= <0x4>;
> +		rockchip,standby_idle = <0x2000>;
> +		rockchip,dram_dll_dis_freq = <300000000>;
> +		rockchip,phy_dll_dis_freq = <125000000>;
> +		rockchip,auto_pd_dis_freq = <666000000>;
> +		rockchip,ddr3_odt_dis_freq = <333000000>;
> +		rockchip,ddr3_drv = <DDR3_DS_40ohm>;
> +		rockchip,ddr3_odt = <DDR3_ODT_120ohm>;
> +		rockchip,phy_ddr3_ca_drv = <PHY_DRV_ODT_40>;
> +		rockchip,phy_ddr3_dq_drv = <PHY_DRV_ODT_40>;
> +		rockchip,phy_ddr3_odt = <PHY_DRV_ODT_240>;
> +		rockchip,lpddr3_odt_dis_freq = <333000000>;
> +		rockchip,lpddr3_drv = <LP3_DS_34ohm>;
> +		rockchip,lpddr3_odt = <LP3_ODT_240ohm>;
> +		rockchip,phy_lpddr3_ca_drv = <PHY_DRV_ODT_40>;
> +		rockchip,phy_lpddr3_dq_drv = <PHY_DRV_ODT_40>;
> +		rockchip,phy_lpddr3_odt = <PHY_DRV_ODT_240>;
> +		rockchip,lpddr4_odt_dis_freq = <333000000>;
> +		rockchip,lpddr4_drv = <LP4_PDDS_60ohm>;
> +		rockchip,lpddr4_dq_odt = <LP4_DQ_ODT_40ohm>;
> +		rockchip,lpddr4_ca_odt = <LP4_CA_ODT_40ohm>;
> +		rockchip,phy_lpddr4_ca_drv = <PHY_DRV_ODT_40>;
> +		rockchip,phy_lpddr4_ck_cs_drv = <PHY_DRV_ODT_80>;
> +		rockchip,phy_lpddr4_dq_drv = <PHY_DRV_ODT_80>;
> +		rockchip,phy_lpddr4_odt = <PHY_DRV_ODT_60>;

These settings aren't board specific?

Rob

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 4/5] arm64: dts: rk3399: Add dfi and dmc nodes.

[Heiko Stuebner]

Hi Gaël,

Am Freitag, 22. März 2019, 00:14:39 CEST schrieb Gaël PORTAY:
> From: Lin Huang <hl@rock-chips.com>
> 
> These are required to support DDR DVFS on rk3399 platform. The patch also
> introduces a new file with default DRAM settings.
> 
> Signed-off-by: Lin Huang <hl@rock-chips.com>
> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
> Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>

> +	dmc: dmc {
> +		compatible = "rockchip,rk3399-dmc";
> +		rockchip,pmu = <&pmugrf>;
> +		devfreq-events = <&dfi>;
> +		clocks = <&cru SCLK_DDRC>;
> +		clock-names = "dmc_clk";
> +		status = "disabled";
> +		rockchip,ddr3_speed_bin = <21>;
> +		rockchip,pd_idle = <0x40>;
> +		rockchip,sr_idle = <0x2>;
> +		rockchip,sr_mc_gate_idle = <0x3>;
> +		rockchip,srpd_lite_idle	= <0x4>;
> +		rockchip,standby_idle = <0x2000>;
> +		rockchip,dram_dll_dis_freq = <300000000>;
> +		rockchip,phy_dll_dis_freq = <125000000>;
> +		rockchip,auto_pd_dis_freq = <666000000>;
> +		rockchip,ddr3_odt_dis_freq = <333000000>;
> +		rockchip,ddr3_drv = <DDR3_DS_40ohm>;
> +		rockchip,ddr3_odt = <DDR3_ODT_120ohm>;
> +		rockchip,phy_ddr3_ca_drv = <PHY_DRV_ODT_40>;
> +		rockchip,phy_ddr3_dq_drv = <PHY_DRV_ODT_40>;
> +		rockchip,phy_ddr3_odt = <PHY_DRV_ODT_240>;
> +		rockchip,lpddr3_odt_dis_freq = <333000000>;
> +		rockchip,lpddr3_drv = <LP3_DS_34ohm>;
> +		rockchip,lpddr3_odt = <LP3_ODT_240ohm>;
> +		rockchip,phy_lpddr3_ca_drv = <PHY_DRV_ODT_40>;
> +		rockchip,phy_lpddr3_dq_drv = <PHY_DRV_ODT_40>;
> +		rockchip,phy_lpddr3_odt = <PHY_DRV_ODT_240>;
> +		rockchip,lpddr4_odt_dis_freq = <333000000>;
> +		rockchip,lpddr4_drv = <LP4_PDDS_60ohm>;
> +		rockchip,lpddr4_dq_odt = <LP4_DQ_ODT_40ohm>;
> +		rockchip,lpddr4_ca_odt = <LP4_CA_ODT_40ohm>;
> +		rockchip,phy_lpddr4_ca_drv = <PHY_DRV_ODT_40>;
> +		rockchip,phy_lpddr4_ck_cs_drv = <PHY_DRV_ODT_80>;
> +		rockchip,phy_lpddr4_dq_drv = <PHY_DRV_ODT_80>;
> +		rockchip,phy_lpddr4_odt = <PHY_DRV_ODT_60>;

as Rob mentioned in his review, these values look board-specific,
so should probably move over to the specific board you're using them
on?


Heiko

Re: [PATCH v3 4/5] arm64: dts: rk3399: Add dfi and dmc nodes.

[Heiko Stuebner]

Hi Gaël,

Am Freitag, 22. März 2019, 00:14:39 CEST schrieb Gaël PORTAY:
> From: Lin Huang <hl@rock-chips.com>
> 
> These are required to support DDR DVFS on rk3399 platform. The patch also
> introduces a new file with default DRAM settings.
> 
> Signed-off-by: Lin Huang <hl@rock-chips.com>
> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
> Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>

> +	dmc: dmc {
> +		compatible = "rockchip,rk3399-dmc";
> +		rockchip,pmu = <&pmugrf>;
> +		devfreq-events = <&dfi>;
> +		clocks = <&cru SCLK_DDRC>;
> +		clock-names = "dmc_clk";
> +		status = "disabled";
> +		rockchip,ddr3_speed_bin = <21>;
> +		rockchip,pd_idle = <0x40>;
> +		rockchip,sr_idle = <0x2>;
> +		rockchip,sr_mc_gate_idle = <0x3>;
> +		rockchip,srpd_lite_idle	= <0x4>;
> +		rockchip,standby_idle = <0x2000>;
> +		rockchip,dram_dll_dis_freq = <300000000>;
> +		rockchip,phy_dll_dis_freq = <125000000>;
> +		rockchip,auto_pd_dis_freq = <666000000>;
> +		rockchip,ddr3_odt_dis_freq = <333000000>;
> +		rockchip,ddr3_drv = <DDR3_DS_40ohm>;
> +		rockchip,ddr3_odt = <DDR3_ODT_120ohm>;
> +		rockchip,phy_ddr3_ca_drv = <PHY_DRV_ODT_40>;
> +		rockchip,phy_ddr3_dq_drv = <PHY_DRV_ODT_40>;
> +		rockchip,phy_ddr3_odt = <PHY_DRV_ODT_240>;
> +		rockchip,lpddr3_odt_dis_freq = <333000000>;
> +		rockchip,lpddr3_drv = <LP3_DS_34ohm>;
> +		rockchip,lpddr3_odt = <LP3_ODT_240ohm>;
> +		rockchip,phy_lpddr3_ca_drv = <PHY_DRV_ODT_40>;
> +		rockchip,phy_lpddr3_dq_drv = <PHY_DRV_ODT_40>;
> +		rockchip,phy_lpddr3_odt = <PHY_DRV_ODT_240>;
> +		rockchip,lpddr4_odt_dis_freq = <333000000>;
> +		rockchip,lpddr4_drv = <LP4_PDDS_60ohm>;
> +		rockchip,lpddr4_dq_odt = <LP4_DQ_ODT_40ohm>;
> +		rockchip,lpddr4_ca_odt = <LP4_CA_ODT_40ohm>;
> +		rockchip,phy_lpddr4_ca_drv = <PHY_DRV_ODT_40>;
> +		rockchip,phy_lpddr4_ck_cs_drv = <PHY_DRV_ODT_80>;
> +		rockchip,phy_lpddr4_dq_drv = <PHY_DRV_ODT_80>;
> +		rockchip,phy_lpddr4_odt = <PHY_DRV_ODT_60>;

as Rob mentioned in his review, these values look board-specific,
so should probably move over to the specific board you're using them
on?


Heiko



_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel