[U-Boot] [PATCH 1/3 v3] armv8: ls1028a: Add NXP LS1028A SoC support

[Yuantian Tang <andy.tang@nxp.com>]

Ls1028a Soc is based on Layerscape Chassis Generation 3.2
architecture with features:
 2 ARM v8 Cortex-A72 cores, CCI400, SEC, DDR3L/4, LCD, GPU, TSN
 ENETC, 2 USB 3.0, 2 eSDHC, 2 FlexCAN, 2 SPI, SATA, 8 I2C controllers,
 6 LPUARTs, GPIO, SAI, qDMA, eDMA, GIC, TMU etc.

Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
---
v3:
	-- fix some issues
 arch/arm/cpu/armv8/fsl-layerscape/Kconfig          |  39 ++-
 arch/arm/cpu/armv8/fsl-layerscape/Makefile         |   4 +
 arch/arm/cpu/armv8/fsl-layerscape/cpu.c            |   3 +
 arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc   |  51 ++++
 arch/arm/cpu/armv8/fsl-layerscape/ls1028a_serdes.c |  73 ++++++
 arch/arm/dts/fsl-ls1028a.dtsi                      | 280 +++++++++++++++++++++
 arch/arm/include/asm/arch-fsl-layerscape/config.h  |  61 +++++
 .../include/asm/arch-fsl-layerscape/immap_lsch3.h  |   9 +
 arch/arm/include/asm/arch-fsl-layerscape/soc.h     |   1 +
 .../asm/arch-fsl-layerscape/stream_id_lsch3.h      |   2 +-
 10 files changed, 521 insertions(+), 2 deletions(-)
 create mode 100644 arch/arm/cpu/armv8/fsl-layerscape/ls1028a_serdes.c
 create mode 100644 arch/arm/dts/fsl-ls1028a.dtsi

diff --git a/arch/arm/cpu/armv8/fsl-layerscape/Kconfig b/arch/arm/cpu/armv8/fsl-layerscape/Kconfig
index f48481f..8ecd095 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/Kconfig
+++ b/arch/arm/cpu/armv8/fsl-layerscape/Kconfig
@@ -20,6 +20,40 @@ config ARCH_LS1012A
 	select SYS_I2C_MXC_I2C2
 	imply PANIC_HANG
 
+config ARCH_LS1028A
+	bool
+	select ARMV8_SET_SMPEN
+	select FSL_LSCH3
+	select NXP_LSCH3_2
+	select SYS_FSL_HAS_CCI400
+	select SYS_FSL_SRDS_1
+	select SYS_HAS_SERDES
+	select SYS_FSL_DDR
+	select SYS_FSL_DDR_LE
+	select SYS_FSL_DDR_VER_50
+	select SYS_FSL_HAS_DDR3
+	select SYS_FSL_HAS_DDR4
+	select SYS_FSL_HAS_SEC
+	select SYS_FSL_SEC_COMPAT_5
+	select SYS_FSL_SEC_LE
+	select FSL_TZASC_1
+	select ARCH_EARLY_INIT_R
+	select BOARD_EARLY_INIT_F
+	select SYS_I2C_MXC
+	select SYS_I2C_MXC_I2C1
+	select SYS_I2C_MXC_I2C2
+	select SYS_I2C_MXC_I2C3
+	select SYS_I2C_MXC_I2C4
+	select SYS_I2C_MXC_I2C5
+	select SYS_I2C_MXC_I2C6
+	select SYS_I2C_MXC_I2C7
+	select SYS_I2C_MXC_I2C8
+	select SYS_FSL_ERRATUM_A009007
+	select SYS_FSL_ERRATUM_A008514 if !TFABOOT
+	select SYS_FSL_ERRATUM_A009663 if !TFABOOT
+	select SYS_FSL_ERRATUM_A009942 if !TFABOOT
+	imply PANIC_HANG
+
 config ARCH_LS1043A
 	bool
 	select ARMV8_SET_SMPEN
@@ -244,6 +278,7 @@ config FSL_PCIE_COMPAT
 	string "PCIe compatible of Kernel DT"
 	depends on PCIE_LAYERSCAPE
 	default "fsl,ls1012a-pcie" if ARCH_LS1012A
+	default "fsl,ls1028a-pcie" if ARCH_LS1028A
 	default "fsl,ls1043a-pcie" if ARCH_LS1043A
 	default "fsl,ls1046a-pcie" if ARCH_LS1046A
 	default "fsl,ls2080a-pcie" if ARCH_LS2080A
@@ -343,6 +378,7 @@ config SYS_FSL_ERRATUM_A010539
 
 config MAX_CPUS
 	int "Maximum number of CPUs permitted for Layerscape"
+	default 2 if ARCH_LS1028A
 	default 4 if ARCH_LS1043A
 	default 4 if ARCH_LS1046A
 	default 16 if ARCH_LS2080A
@@ -377,7 +413,7 @@ config QSPI_AHB_INIT
 config SYS_CCI400_OFFSET
 	hex "Offset for CCI400 base"
 	depends on SYS_FSL_HAS_CCI400
-	default 0x3090000 if ARCH_LS1088A
+	default 0x3090000 if ARCH_LS1088A || ARCH_LS1028A
 	default 0x180000 if FSL_LSCH2
 	help
 	  Offset for CCI400 base
@@ -446,6 +482,7 @@ config CLUSTER_CLK_FREQ
 
 config SYS_FSL_PCLK_DIV
 	int "Platform clock divider"
+	default 1 if ARCH_LS1028A
 	default 1 if ARCH_LS1043A
 	default 1 if ARCH_LS1046A
 	default 1 if ARCH_LS1088A
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/Makefile b/arch/arm/cpu/armv8/fsl-layerscape/Makefile
index e9bc987..a8d3cf9 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/Makefile
+++ b/arch/arm/cpu/armv8/fsl-layerscape/Makefile
@@ -48,3 +48,7 @@ endif
 ifneq ($(CONFIG_ARCH_LS1088A),)
 obj-$(CONFIG_SYS_HAS_SERDES) += ls1088a_serdes.o
 endif
+
+ifneq ($(CONFIG_ARCH_LS1028A),)
+obj-$(CONFIG_SYS_HAS_SERDES) += ls1028a_serdes.o
+endif
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/cpu.c b/arch/arm/cpu/armv8/fsl-layerscape/cpu.c
index 978d46b..c258f2e 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/cpu.c
+++ b/arch/arm/cpu/armv8/fsl-layerscape/cpu.c
@@ -58,6 +58,7 @@ static struct cpu_type cpu_type_list[] = {
 	CPU_TYPE_ENTRY(LS1026A, LS1026A, 2),
 	CPU_TYPE_ENTRY(LS2040A, LS2040A, 4),
 	CPU_TYPE_ENTRY(LS1012A, LS1012A, 1),
+	CPU_TYPE_ENTRY(LS1028A, LS1028A, 2),
 	CPU_TYPE_ENTRY(LS1088A, LS1088A, 8),
 	CPU_TYPE_ENTRY(LS1084A, LS1084A, 8),
 	CPU_TYPE_ENTRY(LS1048A, LS1048A, 4),
@@ -246,11 +247,13 @@ static struct mm_region final_map[] = {
 	  PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
 	  PTE_BLOCK_NON_SHARE | PTE_BLOCK_PXN | PTE_BLOCK_UXN
 	},
+#ifdef CONFIG_SYS_PCIE3_PHYS_ADDR
 	{ CONFIG_SYS_PCIE3_PHYS_ADDR, CONFIG_SYS_PCIE3_PHYS_ADDR,
 	  CONFIG_SYS_PCIE3_PHYS_SIZE,
 	  PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
 	  PTE_BLOCK_NON_SHARE | PTE_BLOCK_PXN | PTE_BLOCK_UXN
 	},
+#endif
 #if defined(CONFIG_ARCH_LS2080A) || defined(CONFIG_ARCH_LX2160A)
 	{ CONFIG_SYS_PCIE4_PHYS_ADDR, CONFIG_SYS_PCIE4_PHYS_ADDR,
 	  CONFIG_SYS_PCIE4_PHYS_SIZE,
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc b/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc
index a0e2621..ad55573 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc
+++ b/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc
@@ -8,6 +8,7 @@ SoC overview
 	6. LS2088A
 	7. LS2081A
 	8. LX2160A
+	9. LS1028A
 
 LS1043A
 ---------
@@ -328,3 +329,53 @@ LX2160A SoC has 2 more similar SoC personalities
 
 2)LX2080A, few difference w.r.t. LX2160A:
        a) Eight 64-bit ARM v8 Cortex-A72 CPUs
+
+
+LS1028A
+--------
+The QorIQ LS1028A processor integrates two 64-bit Arm Cortex-A72 cores with
+a GPU and LCD controller, as well as two TSN-enabled Ethernet controllers and
+a TSNenabled 4-port switch.
+
+The high performance Cortex-A72 cores, performing above 16,000 CoreMarks,
+combined with 2.5 Gbit Ethernet, PCI express Gen 3.0, SATA 3.0, USB 3.0 and
+Octal/Quad SPI interfaces provide capabilities for a number of industrial and
+embedded applications. The device provides excellent integration with the
+new Time-Sensitive Networking standard, and enables a number of
+TSN applications.
+
+The LS1028A SoC includes the following function and features:
+ - Two 64-bit ARM v8 A72 CPUs
+ - Cache Coherent interconnect (CCI-400)
+ - One 32-bit DDR3L/DDR4 SDRAM memory controller with ECC
+ - eDP/Displayport interface
+ - Graphics processing unit
+ - One Configurable x4 SerDes
+ - Ethernet interfaces
+   - Non-switched: One Ethernet MAC supporting 2.5G, 1G, 100M, 10M, one
+   ethernet MAC supporting 1G, 100M, 10M.
+   - Switched: TSN IP to support four 2.5/1G interfaces.
+   - None of the MACs support MACSEC
+   - Support for RGMII, SGMII (and 1000Base-KX), SGMII 2.5x, QSGMII
+   - Support for 10G-SXGMII and 10G-QXGMII.
+   - Energy efficient Ethernet support (802.3az)
+   - IEEE 1588 support
+  - High-speed peripheral interfaces
+    - Two PCIe 3.0 controllers, one supporting x4 operation
+    - One serial ATA (SATA 3.0) controller
+  - Additional peripheral interfaces
+    - Two high-speed USB 2.0/3.0 controllers with integrated PHY each
+      supporting host or device modes
+    - Two Enhanced secure digital host controllers (SD/SDIO/eMMC)
+    - Two Serial peripheral interface (SPI) controllers
+    - Eight I2C controllers
+    - Two UART controllers
+    - Additional six Industrual UARTs (LPUART).
+    - One FlexSPI controller
+    - General Purpose IO (GPIO)
+    - Two CAN-FD interfaces
+    - Eight Flextimers with PWM I/O
+  - Support for hardware virtualization and partitioning enforcement
+  - Layerscape Trust Architecture
+  - Service Processor (SP) provides pre-boot initialization and secure-boot
+    capabilities
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/ls1028a_serdes.c b/arch/arm/cpu/armv8/fsl-layerscape/ls1028a_serdes.c
new file mode 100644
index 0000000..ef598c4
--- /dev/null
+++ b/arch/arm/cpu/armv8/fsl-layerscape/ls1028a_serdes.c
@@ -0,0 +1,73 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019 NXP
+ */
+
+#include <common.h>
+#include <asm/arch/fsl_serdes.h>
+
+struct serdes_config {
+	u32 protocol;
+	u8 lanes[SRDS_MAX_LANES];
+	u8 rcw_lanes[SRDS_MAX_LANES];
+};
+
+static struct serdes_config serdes1_cfg_tbl[] = {
+	/* SerDes 1 */
+	{0xCC5B, {PCIE1, QSGMII_B, PCIE2, PCIE2} },
+	{0xEB99, {SGMII1, SGMII1, PCIE2, SATA1} },
+	{0xCC99, {SGMII1, SGMII1, PCIE2, PCIE2} },
+	{0xBB99, {SGMII1, SGMII1, PCIE2, PCIE1} },
+	{0x9999, {SGMII1, SGMII2, SGMII3, SGMII4} },
+	{0xEBCC, {PCIE1, PCIE1, PCIE2, SATA1} },
+	{0xCCCC, {PCIE1, PCIE1, PCIE2, PCIE2} },
+	{0xDDDD, {PCIE1, PCIE1, PCIE1, PCIE1} },
+	{}
+};
+
+static struct serdes_config *serdes_cfg_tbl[] = {
+	serdes1_cfg_tbl,
+};
+
+enum srds_prtcl serdes_get_prtcl(int serdes, int cfg, int lane)
+{
+	struct serdes_config *ptr;
+
+	if (serdes >= ARRAY_SIZE(serdes_cfg_tbl))
+		return 0;
+
+	ptr = serdes_cfg_tbl[serdes];
+	while (ptr->protocol) {
+		if (ptr->protocol == cfg)
+			return ptr->lanes[lane];
+		ptr++;
+	}
+
+	return 0;
+}
+
+int is_serdes_prtcl_valid(int serdes, u32 prtcl)
+{
+	int i;
+	struct serdes_config *ptr;
+
+	if (serdes >= ARRAY_SIZE(serdes_cfg_tbl))
+		return 0;
+
+	ptr = serdes_cfg_tbl[serdes];
+	while (ptr->protocol) {
+		if (ptr->protocol == prtcl)
+			break;
+		ptr++;
+	}
+
+	if (!ptr->protocol)
+		return 0;
+
+	for (i = 0; i < SRDS_MAX_LANES; i++) {
+		if (ptr->lanes[i] != NONE)
+			return 1;
+	}
+
+	return 0;
+}
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi
new file mode 100644
index 0000000..1274d2c
--- /dev/null
+++ b/arch/arm/dts/fsl-ls1028a.dtsi
@@ -0,0 +1,280 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * NXP ls1028a SOC common device tree source
+ *
+ * Copyright 2019 NXP
+ *
+ */
+
+/ {
+	compatible = "fsl,ls1028a";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	sysclk: sysclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+		clock-output-names = "sysclk";
+	};
+
+	clockgen: clocking at 1300000 {
+		compatible = "fsl,ls1028a-clockgen";
+		reg = <0x0 0x1300000 0x0 0xa0000>;
+		#clock-cells = <2>;
+		clocks = <&sysclk>;
+	};
+
+	memory at 01080000 {
+		device_type = "memory";
+		reg = <0x00000000 0x01080000 0 0x80000000>;
+		      /* DRAM space - 1, size : 2 GB DRAM */
+	};
+
+	gic: interrupt-controller at 6000000 {
+		compatible = "arm,gic-v3";
+		reg = <0x0 0x06000000 0 0x10000>, /* GIC Dist */
+			  <0x0 0x06040000 0 0x40000>;
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		interrupts = <1 9 0x4>;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <1 13 0x8>, /* Physical Secure PPI, active-low */
+			     <1 14 0x8>, /* Physical Non-Secure PPI, active-low */
+			     <1 11 0x8>, /* Virtual PPI, active-low */
+			     <1 10 0x8>; /* Hypervisor PPI, active-low */
+	};
+
+	fspi: flexspi at 20C0000 {
+		compatible = "nxp,dn-fspi";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x0 0x20C0000 0x0 0x10000>,
+			<0x0 0x20000000 0x0 0x10000000>; /*64MB flash*/
+		reg-names = "FSPI", "FSPI-memory";
+		num-cs = <1>;
+		status = "disabled";
+	};
+
+	serial0: serial at 21c0500 {
+		device_type = "serial";
+		compatible = "fsl,ns16550", "ns16550a";
+		reg = <0x0 0x21c0500 0x0 0x100>;
+		interrupts = <0 32 0x1>; /* edge triggered */
+		status = "disabled";
+	};
+
+	serial1: serial at 21c0600 {
+		device_type = "serial";
+		compatible = "fsl,ns16550", "ns16550a";
+		reg = <0x0 0x21c0600 0x0 0x100>;
+		interrupts = <0 32 0x1>; /* edge triggered */
+		status = "disabled";
+	};
+
+	pcie at 3400000 {
+	       compatible = "fsl,ls-pcie", "fsl,ls1028-pcie", "snps,dw-pcie";
+	       reg = <0x00 0x03400000 0x0 0x80000
+		       0x00 0x03480000 0x0 0x40000   /* lut registers */
+		       0x00 0x034c0000 0x0 0x40000  /* pf controls registers */
+		       0x80 0x00000000 0x0 0x20000>; /* configuration space */
+	       reg-names = "dbi", "lut", "ctrl", "config";
+	       #address-cells = <3>;
+	       #size-cells = <2>;
+	       device_type = "pci";
+	       num-lanes = <4>;
+	       bus-range = <0x0 0xff>;
+	       ranges = <0x81000000 0x0 0x00000000 0x80 0x00020000 0x0 0x00010000   /* downstream I/O */
+		       0x82000000 0x0 0x40000000 0x80 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+	};
+
+	pcie at 3500000 {
+	       compatible = "fsl,ls-pcie", "fsl,ls1028-pcie", "snps,dw-pcie";
+	       reg = <0x00 0x03500000 0x0 0x80000
+		       0x00 0x03580000 0x0 0x40000   /* lut registers */
+		       0x00 0x035c0000 0x0 0x40000  /* pf controls registers */
+		       0x88 0x00000000 0x0 0x20000>; /* configuration space */
+	       reg-names = "dbi", "lut", "ctrl", "config";
+	       #address-cells = <3>;
+	       #size-cells = <2>;
+	       device_type = "pci";
+	       num-lanes = <4>;
+	       bus-range = <0x0 0xff>;
+	       ranges = <0x81000000 0x0 0x00000000 0x88 0x00020000 0x0 0x00010000   /* downstream I/O */
+		       0x82000000 0x0 0x40000000 0x88 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+	};
+
+	i2c0: i2c at 2000000 {
+		compatible = "fsl,vf610-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x0 0x2000000 0x0 0x10000>;
+		interrupts = <0 34 0x4>;
+		clock-names = "i2c";
+		clocks = <&clockgen 4 0>;
+		status = "disabled";
+	};
+
+	i2c1: i2c at 2010000 {
+		compatible = "fsl,vf610-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x0 0x2010000 0x0 0x10000>;
+		interrupts = <0 34 0x4>;
+		clock-names = "i2c";
+		clocks = <&clockgen 4 0>;
+		status = "disabled";
+	};
+
+	i2c2: i2c at 2020000 {
+		compatible = "fsl,vf610-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x0 0x2020000 0x0 0x10000>;
+		interrupts = <0 35 0x4>;
+		clock-names = "i2c";
+		clocks = <&clockgen 4 0>;
+		status = "disabled";
+	};
+
+	i2c3: i2c at 2030000 {
+		compatible = "fsl,vf610-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x0 0x2030000 0x0 0x10000>;
+		interrupts = <0 35 0x4>;
+		clock-names = "i2c";
+		clocks = <&clockgen 4 0>;
+		status = "disabled";
+	};
+
+	i2c4: i2c at 2040000 {
+		compatible = "fsl,vf610-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x0 0x2040000 0x0 0x10000>;
+		interrupts = <0 74 0x4>;
+		clock-names = "i2c";
+		clocks = <&clockgen 4 0>;
+		status = "disabled";
+	};
+
+	i2c5: i2c at 2050000 {
+		compatible = "fsl,vf610-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x0 0x2050000 0x0 0x10000>;
+		interrupts = <0 74 0x4>;
+		clock-names = "i2c";
+		clocks = <&clockgen 4 0>;
+		status = "disabled";
+	};
+
+	i2c6: i2c at 2060000 {
+		compatible = "fsl,vf610-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x0 0x2060000 0x0 0x10000>;
+		interrupts = <0 75 0x4>;
+		clock-names = "i2c";
+		clocks = <&clockgen 4 0>;
+		status = "disabled";
+	};
+
+	i2c7: i2c at 2070000 {
+		compatible = "fsl,vf610-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x0 0x2070000 0x0 0x10000>;
+		interrupts = <0 75 0x4>;
+		clock-names = "i2c";
+		clocks = <&clockgen 4 0>;
+		status = "disabled";
+	};
+
+	usb1: usb3 at 3100000 {
+		compatible = "fsl,layerscape-dwc3";
+		reg = <0x0 0x3100000 0x0 0x10000>;
+		interrupts = <0 80 0x4>;
+		dr_mode = "host";
+		status = "disabled";
+	};
+
+	usb2: usb3 at 3110000 {
+		compatible = "fsl,layerscape-dwc3";
+		reg = <0x0 0x3110000 0x0 0x10000>;
+		interrupts = <0 81 0x4>;
+		dr_mode = "host";
+		status = "disabled";
+	};
+
+	dspi0: dspi at 2100000 {
+		compatible = "fsl,vf610-dspi";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x0 0x2100000 0x0 0x10000>;
+		interrupts = <0 26 0x4>;
+		clock-names = "dspi";
+		clocks = <&clockgen 4 0>;
+		num-cs = <5>;
+		litte-endian;
+		status = "disabled";
+	};
+
+	dspi1: dspi at 2110000 {
+		compatible = "fsl,vf610-dspi";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x0 0x2110000 0x0 0x10000>;
+		interrupts = <0 26 0x4>;
+		clock-names = "dspi";
+		clocks = <&clockgen 4 0>;
+		num-cs = <5>;
+		little-endian;
+		status = "disabled";
+	};
+
+	dspi2: dspi at 2120000 {
+		compatible = "fsl,vf610-dspi";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x0 0x2120000 0x0 0x10000>;
+		interrupts = <0 26 0x4>;
+		clock-names = "dspi";
+		clocks = <&clockgen 4 0>;
+		num-cs = <5>;
+		little-endian;
+		status = "disabled";
+	};
+
+	esdhc0: esdhc at 2140000 {
+		compatible = "fsl,esdhc";
+		reg = <0x0 0x2140000 0x0 0x10000>;
+		interrupts = <0 28 0x4>;
+		big-endian;
+		bus-width = <4>;
+		status = "disabled";
+	};
+
+	esdhc1: esdhc at 2150000 {
+		compatible = "fsl,esdhc";
+		reg = <0x0 0x2150000 0x0 0x10000>;
+		interrupts = <0 63 0x4>;
+		big-endian;
+		non-removable;
+		bus-width = <4>;
+		status = "disabled";
+	};
+
+	sata: sata at 3200000 {
+		compatible = "fsl,ls1028a-ahci";
+		reg = <0x0 0x3200000 0x0 0x10000>;
+		interrupts = <0 133 4>;
+		clocks = <&clockgen 4 1>;
+		status = "disabled";
+	};
+};
diff --git a/arch/arm/include/asm/arch-fsl-layerscape/config.h b/arch/arm/include/asm/arch-fsl-layerscape/config.h
index 903d509..eb21c09 100644
--- a/arch/arm/include/asm/arch-fsl-layerscape/config.h
+++ b/arch/arm/include/asm/arch-fsl-layerscape/config.h
@@ -229,6 +229,67 @@
 
 #define CONFIG_SYS_FSL_MAX_NUM_OF_SEC		1
 
+#elif defined(CONFIG_ARCH_LS1028A)
+#define CONFIG_SYS_FSL_NUM_CC_PLLS		3
+#define CONFIG_SYS_FSL_CLUSTER_CLOCKS		{ 1, 1 }
+#define CONFIG_GICV3
+#define CONFIG_FSL_TZPC_BP147
+#define CONFIG_FSL_TZASC_400
+
+/* TZ Protection Controller Definitions */
+#define TZPC_BASE				0x02200000
+#define TZPCR0SIZE_BASE				(TZPC_BASE)
+#define TZPCDECPROT_0_STAT_BASE			(TZPC_BASE + 0x800)
+#define TZPCDECPROT_0_SET_BASE			(TZPC_BASE + 0x804)
+#define TZPCDECPROT_0_CLR_BASE			(TZPC_BASE + 0x808)
+#define TZPCDECPROT_1_STAT_BASE			(TZPC_BASE + 0x80C)
+#define TZPCDECPROT_1_SET_BASE			(TZPC_BASE + 0x810)
+#define TZPCDECPROT_1_CLR_BASE			(TZPC_BASE + 0x814)
+#define TZPCDECPROT_2_STAT_BASE			(TZPC_BASE + 0x818)
+#define TZPCDECPROT_2_SET_BASE			(TZPC_BASE + 0x81C)
+#define TZPCDECPROT_2_CLR_BASE			(TZPC_BASE + 0x820)
+
+#define	SRDS_MAX_LANES	4
+
+#define CONFIG_SYS_FSL_OCRAM_BASE		0x18000000 /* initial RAM */
+#define SYS_FSL_OCRAM_SPACE_SIZE		0x00200000 /* 2M */
+#define CONFIG_SYS_FSL_OCRAM_SIZE		0x00040000 /* Real size 256K */
+
+/* Generic Interrupt Controller Definitions */
+#define GICD_BASE				0x06000000
+#define GICR_BASE				0x06040000
+
+/* SMMU Definitions */
+#define SMMU_BASE				0x05000000 /* GR0 Base */
+
+/* DDR */
+#define CONFIG_SYS_DDR_BLOCK1_SIZE	((phys_size_t)2 << 30)
+#define CONFIG_MAX_MEM_MAPPED		CONFIG_SYS_DDR_BLOCK1_SIZE
+
+#define CONFIG_SYS_FSL_CCSR_GUR_LE
+#define CONFIG_SYS_FSL_CCSR_SCFG_LE
+#define CONFIG_SYS_FSL_ESDHC_LE
+#define CONFIG_SYS_FSL_PEX_LUT_LE
+
+#define CONFIG_SYS_MEMAC_LITTLE_ENDIAN
+
+/* SFP */
+#define CONFIG_SYS_FSL_SFP_VER_3_4
+#define CONFIG_SYS_FSL_SFP_LE
+#define CONFIG_SYS_FSL_SRK_LE
+
+/* SEC */
+#define CONFIG_SYS_FSL_MAX_NUM_OF_SEC		1
+
+/* Security Monitor */
+#define CONFIG_SYS_FSL_SEC_MON_LE
+
+/* Secure Boot */
+#define CONFIG_ESBC_HDR_LS
+
+/* DCFG - GUR */
+#define CONFIG_SYS_FSL_CCSR_GUR_LE
+
 #elif defined(CONFIG_FSL_LSCH2)
 #define CONFIG_SYS_FSL_OCRAM_BASE		0x10000000 /* initial RAM */
 #define SYS_FSL_OCRAM_SPACE_SIZE		0x00200000 /* 2M space */
diff --git a/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h b/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
index 9fab88a..dbf3215 100644
--- a/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
+++ b/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
@@ -171,6 +171,9 @@
 #define CONFIG_SYS_PCIE1_PHYS_ADDR		0x2000000000ULL
 #define CONFIG_SYS_PCIE2_PHYS_ADDR		0x2800000000ULL
 #define CONFIG_SYS_PCIE3_PHYS_ADDR		0x3000000000ULL
+#elif CONFIG_ARCH_LS1028A
+#define CONFIG_SYS_PCIE1_PHYS_ADDR		0x8000000000ULL
+#define CONFIG_SYS_PCIE2_PHYS_ADDR		0x8800000000ULL
 #else
 #define CONFIG_SYS_PCIE1_PHYS_ADDR		0x1000000000ULL
 #define CONFIG_SYS_PCIE2_PHYS_ADDR		0x1200000000ULL
@@ -375,6 +378,12 @@ struct ccsr_gur {
 #define FSL_CHASSIS3_SRDS2_PRTCL_SHIFT	FSL_CHASSIS3_RCWSR30_SRDS2_PRTCL_SHIFT
 #define FSL_CHASSIS3_SRDS1_REGSR	29
 #define FSL_CHASSIS3_SRDS2_REGSR	30
+#elif defined(CONFIG_ARCH_LS1028A)
+#define	FSL_CHASSIS3_RCWSR29_SRDS1_PRTCL_MASK	0xFFFF0000
+#define	FSL_CHASSIS3_RCWSR29_SRDS1_PRTCL_SHIFT	16
+#define FSL_CHASSIS3_SRDS1_PRTCL_MASK	FSL_CHASSIS3_RCWSR29_SRDS1_PRTCL_MASK
+#define FSL_CHASSIS3_SRDS1_PRTCL_SHIFT	FSL_CHASSIS3_RCWSR29_SRDS1_PRTCL_SHIFT
+#define FSL_CHASSIS3_SRDS1_REGSR	29
 #endif
 #define RCW_SB_EN_REG_INDEX	9
 #define RCW_SB_EN_MASK		0x00000400
diff --git a/arch/arm/include/asm/arch-fsl-layerscape/soc.h b/arch/arm/include/asm/arch-fsl-layerscape/soc.h
index 7d95c4e..234440b 100644
--- a/arch/arm/include/asm/arch-fsl-layerscape/soc.h
+++ b/arch/arm/include/asm/arch-fsl-layerscape/soc.h
@@ -83,6 +83,7 @@ enum boot_src get_boot_src(void);
 /* LS1043A/LS1023A 23x23 package silicon has different value of VAR_PER */
 #define SVR_LS1043A_P23		0x879202
 #define SVR_LS1023A_P23		0x87920A
+#define SVR_LS1028A		0x870B00
 #define SVR_LS1046A		0x870700
 #define SVR_LS1026A		0x870708
 #define SVR_LS1048A		0x870320
diff --git a/arch/arm/include/asm/arch-fsl-layerscape/stream_id_lsch3.h b/arch/arm/include/asm/arch-fsl-layerscape/stream_id_lsch3.h
index e017d8b..c53cc57 100644
--- a/arch/arm/include/asm/arch-fsl-layerscape/stream_id_lsch3.h
+++ b/arch/arm/include/asm/arch-fsl-layerscape/stream_id_lsch3.h
@@ -87,7 +87,7 @@
 #define FSL_PEX_STREAM_ID_NUM		(0x100)
 #endif
 
-#if defined(CONFIG_ARCH_LS2080A)
+#if defined(CONFIG_ARCH_LS2080A) || defined(CONFIG_ARCH_LS1028A)
 #define FSL_PEX_STREAM_ID_END		22
 #elif defined(CONFIG_ARCH_LS1088A)
 #define FSL_PEX_STREAM_ID_END		18
-- 
2.7.4