All of lore.kernel.org
 help / color / mirror / Atom feed
* [U-Boot] [PATCH v1] sunxi: Add support for Olimex A64-Teres-I board
@ 2019-04-14 16:46 Jonas Smedegaard
  2019-04-14 17:36 ` Jagan Teki
  0 siblings, 1 reply; 3+ messages in thread
From: Jonas Smedegaard @ 2019-04-14 16:46 UTC (permalink / raw)
  To: u-boot

Olimex Teres-I is a laptop DIY kit, and A64-Teres-I is its mainboard.
https://linux-sunxi.org/Olimex_Teres-A64

This patch enables support for the A64-Teres-I board to u-boot,
including enabling screen backlight (lacking from Linux device-tree).

sun50i-a64-teres-i.dts is copied verbatim from Linux 5.0.
Cosmetic warnings regarding whitespace and placement of SPDX notice for
this file was ignored.

config and .dtsi file are adapted from pinebook files.

Author: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Jonas Smedegaard <dr@jones.dk>
---

 arch/arm/dts/Makefile                       |   3 +-
 arch/arm/dts/sun50i-a64-teres-i-u-boot.dtsi |  41 +++
 arch/arm/dts/sun50i-a64-teres-i.dts         | 270 ++++++++++++++++++++
 configs/teres_i_defconfig                   |  21 ++
 4 files changed, 334 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/dts/sun50i-a64-teres-i-u-boot.dtsi
 create mode 100644 arch/arm/dts/sun50i-a64-teres-i.dts
 create mode 100644 configs/teres_i_defconfig

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 8167cdb4e8..a12ed81f49 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -483,7 +483,8 @@ dtb-$(CONFIG_MACH_SUN50I) += \
 	sun50i-a64-pine64-plus.dtb \
 	sun50i-a64-pine64.dtb \
 	sun50i-a64-pinebook.dtb \
-	sun50i-a64-sopine-baseboard.dtb
+	sun50i-a64-sopine-baseboard.dtb \
+	sun50i-a64-teres-i.dtb
 dtb-$(CONFIG_MACH_SUN9I) += \
 	sun9i-a80-optimus.dtb \
 	sun9i-a80-cubieboard4.dtb \
diff --git a/arch/arm/dts/sun50i-a64-teres-i-u-boot.dtsi b/arch/arm/dts/sun50i-a64-teres-i-u-boot.dtsi
new file mode 100644
index 0000000000..1a64b7d09c
--- /dev/null
+++ b/arch/arm/dts/sun50i-a64-teres-i-u-boot.dtsi
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Vasily Khoruzhick <anarsoul@gmail.com>
+ *
+ */
+
+#include "sunxi-u-boot.dtsi"
+
+/ {
+	vdd_bl: regulator at 0 {
+		compatible = "regulator-fixed";
+		regulator-name = "bl-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+		enable-active-high;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 50000 0>;
+		brightness-levels = <0 5 10 15 20 30 40 55 70 85 100>;
+		default-brightness-level = <2>;
+		enable-gpios = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* PD23 */
+		power-supply = <&vdd_bl>;
+	};
+};
+
+/* The ANX6345 eDP-bridge is on i2c */
+&i2c0 {
+	anx6345: edp-bridge at 38 {
+		compatible = "analogix,anx6345";
+		reg = <0x38>;
+		reset-gpios = <&pio 3 24 GPIO_ACTIVE_LOW>; /* PD24 */
+		status = "okay";
+	};
+};
+
+&pwm {
+	status = "okay";
+};
diff --git a/arch/arm/dts/sun50i-a64-teres-i.dts b/arch/arm/dts/sun50i-a64-teres-i.dts
new file mode 100644
index 0000000000..c455b24dd0
--- /dev/null
+++ b/arch/arm/dts/sun50i-a64-teres-i.dts
@@ -0,0 +1,270 @@
+/*
+ * Copyright (C) Harald Geyer <harald@ccbib.org>
+ * based on sun50i-a64-olinuxino.dts by Jagan Teki <jteki@openedev.com>
+ *
+ * SPDX-License-Identifier: (GPL-2.0 OR MIT)
+ */
+
+/dts-v1/;
+
+#include "sun50i-a64.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "Olimex A64 Teres-I";
+	compatible = "olimex,a64-teres-i", "allwinner,sun50i-a64";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+
+		framebuffer-lcd {
+			eDP25-supply = <&reg_dldo2>;
+			eDP12-supply = <&reg_dldo3>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		lid-switch {
+			label = "Lid Switch";
+			gpios = <&r_pio 0 8 GPIO_ACTIVE_LOW>; /* PL8 */
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		capslock {
+			label = "teres-i:green:capslock";
+			gpios = <&pio 2 7 GPIO_ACTIVE_HIGH>; /* PC7 */
+		};
+
+		numlock {
+			label = "teres-i:green:numlock";
+			gpios = <&pio 2 4 GPIO_ACTIVE_HIGH>; /* PC4 */
+		};
+	};
+
+	reg_usb1_vbus: usb1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */
+		status = "okay";
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+	};
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+
+/* The ANX6345 eDP-bridge is on i2c0. There is no linux (mainline)
+ * driver for this chip at the moment, the bootloader initializes it.
+ * However it can be accessed with the i2c-dev driver from user space.
+ */
+&i2c0 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	status = "okay";
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&reg_aldo2>;
+	vqmmc-supply = <&reg_dldo4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	rtl8723bs: wifi at 1 {
+		reg = <1>;
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	vqmmc-supply = <&reg_dcdc1>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp803: pmic at 3a3 {
+		compatible = "x-powers,axp803";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		wakeup-source;
+	};
+};
+
+#include "axp803.dtsi"
+
+&reg_aldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "vcc-pe";
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1040000>;
+	regulator-max-microvolt = <1300000>;
+	regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vcc-ddr3";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-hdmi";
+};
+
+&reg_dldo2 {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	regulator-name = "vcc-pd";
+};
+
+&reg_dldo3 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vdd-edp";
+};
+
+&reg_dldo4 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi-io";
+};
+
+&reg_eldo1 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "cpvdd";
+};
+
+&reg_eldo2 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-dvdd-csi";
+};
+
+&reg_fldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-1v2-hsic";
+};
+
+/*
+ * The A64 chip cannot work without this regulator off, although
+ * it seems to be only driving the AR100 core.
+ * Maybe we don't still know well about CPUs domain.
+ */
+&reg_fldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
+&simplefb_hdmi {
+	vcc-hdmi-supply = <&reg_dldo1>;
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};
diff --git a/configs/teres_i_defconfig b/configs/teres_i_defconfig
new file mode 100644
index 0000000000..939dc24408
--- /dev/null
+++ b/configs/teres_i_defconfig
@@ -0,0 +1,21 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_SPL=y
+CONFIG_MACH_SUN50I=y
+CONFIG_DRAM_CLK=552
+CONFIG_DRAM_ZQ=3881949
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+CONFIG_I2C0_ENABLE=y
+# CONFIG_CMD_FLASH is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-teres-i"
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_PWM=y
+CONFIG_PWM_SUNXI=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
+# CONFIG_USB_GADGET is not set
+CONFIG_VIDEO_BRIDGE=y
+CONFIG_VIDEO_BRIDGE_ANALOGIX_ANX6345=y
-- 
2.20.1

^ permalink raw reply related	[flat|nested] 3+ messages in thread
end of thread, other threads:[~2019-04-14 21:49 UTC | newest]

Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-04-14 16:46 [U-Boot] [PATCH v1] sunxi: Add support for Olimex A64-Teres-I board Jonas Smedegaard
2019-04-14 17:36 ` Jagan Teki
2019-04-14 21:49   ` Jonas Smedegaard

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.