[PATCH V2 1/8] ARM: dts: imx53: Update UART configuration on M53Menlo

[PATCH V2 1/8] ARM: dts: imx53: Update UART configuration on M53Menlo

[Marek Vasut]

Enable flow control lines on UART1 and UART2, add matching pinmux entries.
Add and enable UART3 with RS485 mode enabled on boot.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
 arch/arm/boot/dts/imx53-m53menlo.dts | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/arch/arm/boot/dts/imx53-m53menlo.dts b/arch/arm/boot/dts/imx53-m53menlo.dts
index f0a3fde0739c..62bc6a95a477 100644
--- a/arch/arm/boot/dts/imx53-m53menlo.dts
+++ b/arch/arm/boot/dts/imx53-m53menlo.dts
@@ -244,6 +244,8 @@
 			fsl,pins = <
 				MX53_PAD_PATA_DIOW__UART1_TXD_MUX	0x1e4
 				MX53_PAD_PATA_DMACK__UART1_RXD_MUX	0x1e4
+				MX53_PAD_PATA_IORDY__UART1_RTS		0x1e4
+				MX53_PAD_PATA_RESET_B__UART1_CTS	0x1e4
 			>;
 		};
 
@@ -251,6 +253,16 @@
 			fsl,pins = <
 				MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX	0x1e4
 				MX53_PAD_PATA_DMARQ__UART2_TXD_MUX	0x1e4
+				MX53_PAD_PATA_DIOR__UART2_RTS		0x1e4
+				MX53_PAD_PATA_INTRQ__UART2_CTS		0x1e4
+			>;
+		};
+
+		pinctrl_uart3: uart3grp {
+			fsl,pins = <
+				MX53_PAD_PATA_CS_1__UART3_RXD_MUX	0x1e4
+				MX53_PAD_PATA_CS_0__UART3_TXD_MUX	0x1e4
+				MX53_PAD_PATA_DA_2__UART3_RTS		0x1e4
 			>;
 		};
 
@@ -287,12 +299,21 @@
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
+	uart-has-rtscts;
 	status = "okay";
 };
 
 &uart2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	linux,rs485-enabled-at-boot-time;
 	status = "okay";
 };
 
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V2 2/8] ARM: dts: imx53: Update USB configuration on M53Menlo

[Marek Vasut]

Turn USBH1 into Host and update the GPIO polarity of the
regulator to match new hardware.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
---
V2: Add enable-active-high property to the regulator node
---
 arch/arm/boot/dts/imx53-m53menlo.dts | 11 +++++++----
 1 file changed, 7 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx53-m53menlo.dts b/arch/arm/boot/dts/imx53-m53menlo.dts
index 62bc6a95a477..7dddd7028bec 100644
--- a/arch/arm/boot/dts/imx53-m53menlo.dts
+++ b/arch/arm/boot/dts/imx53-m53menlo.dts
@@ -50,7 +50,8 @@
 		regulator-name = "vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+		gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 };
 
@@ -268,8 +269,10 @@
 
 		pinctrl_usb: usbgrp {
 			fsl,pins = <
-				MX53_PAD_GPIO_2__GPIO1_2		0x1d5
-				MX53_PAD_GPIO_3__USBOH3_USBH1_OC	0x1d5
+				MX53_PAD_GPIO_2__GPIO1_2		0x1c4
+				MX53_PAD_GPIO_3__USBOH3_USBH1_OC	0x1c4
+				MX53_PAD_GPIO_4__GPIO1_4		0x1c4
+				MX53_PAD_GPIO_18__GPIO7_13		0x1c4
 			>;
 		};
 	};
@@ -322,7 +325,7 @@
 	pinctrl-0 = <&pinctrl_usb>;
 	vbus-supply = <&reg_usbh1_vbus>;
 	phy_type = "utmi";
-	dr_mode = "peripheral";
+	dr_mode = "host";
 	status = "okay";
 };
 
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V2 3/8] ARM: dts: imx53: Add ethernet PHY reset on M53Menlo

[Marek Vasut]

Add ethernet PHY GPIO reset line, to let the kernel to reset the PHY.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
---
V2: Set reset GPIO as active-low, to match the board
---
 arch/arm/boot/dts/imx53-m53menlo.dts | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/imx53-m53menlo.dts b/arch/arm/boot/dts/imx53-m53menlo.dts
index 7dddd7028bec..97a8aee9d7d6 100644
--- a/arch/arm/boot/dts/imx53-m53menlo.dts
+++ b/arch/arm/boot/dts/imx53-m53menlo.dts
@@ -87,6 +87,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_fec>;
 	phy-mode = "rmii";
+	phy-reset-gpios = <&gpio7 7 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V2 4/8] ARM: dts: imx53: Select netdev trigger for Yellow LED on M53Menlo

[Marek Vasut]

The yellow LED is in the ethernet jack socket, bind it to netdev
trigger to indicate ethernet activity.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
 arch/arm/boot/dts/imx53-m53menlo.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx53-m53menlo.dts b/arch/arm/boot/dts/imx53-m53menlo.dts
index 97a8aee9d7d6..10a738a09d0a 100644
--- a/arch/arm/boot/dts/imx53-m53menlo.dts
+++ b/arch/arm/boot/dts/imx53-m53menlo.dts
@@ -30,7 +30,7 @@
 		eth {
 			label = "EthLedYe";
 			gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "none";
+			linux,default-trigger = "netdev";
 		};
 	};
 
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V2 5/8] ARM: dts: imx53: Add power GPIOs on M53Menlo

[Marek Vasut]

Add GPIO power button and GPIO poweroff, which is present on new hardware.
These let the system power itself off on shutdown.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
 arch/arm/boot/dts/imx53-m53menlo.dts | 31 ++++++++++++++++++++++++++++
 1 file changed, 31 insertions(+)

diff --git a/arch/arm/boot/dts/imx53-m53menlo.dts b/arch/arm/boot/dts/imx53-m53menlo.dts
index 10a738a09d0a..1a8cdef49261 100644
--- a/arch/arm/boot/dts/imx53-m53menlo.dts
+++ b/arch/arm/boot/dts/imx53-m53menlo.dts
@@ -10,6 +10,25 @@
 	model = "MENLO M53 EMBEDDED DEVICE";
 	compatible = "menlo,m53menlo", "fsl,imx53";
 
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&pinctrl_power_button>;
+		pinctrl-names = "default";
+
+		power-button {
+			label = "Power button";
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+		};
+	};
+
+	gpio-poweroff {
+		compatible = "gpio-poweroff";
+		pinctrl-0 = <&pinctrl_power_out>;
+		pinctrl-names = "default";
+		gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@@ -242,6 +261,18 @@
 			>;
 		};
 
+		pinctrl_power_button: powerbutgrp {
+			fsl,pins = <
+				MX53_PAD_SD2_DATA2__GPIO1_13		0x1e4
+			>;
+		};
+
+		pinctrl_power_out: poweroutgrp {
+			fsl,pins = <
+				MX53_PAD_SD2_DATA0__GPIO1_15		0x1e4
+			>;
+		};
+
 		pinctrl_uart1: uart1grp {
 			fsl,pins = <
 				MX53_PAD_PATA_DIOW__UART1_TXD_MUX	0x1e4
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V2 6/8] ARM: dts: imx53: Add GPIO beeper on M53Menlo

[Marek Vasut]

Add GPIO beeper, to let the board produce beeps.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
 arch/arm/boot/dts/imx53-m53menlo.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/imx53-m53menlo.dts b/arch/arm/boot/dts/imx53-m53menlo.dts
index 1a8cdef49261..39a76a5bbd19 100644
--- a/arch/arm/boot/dts/imx53-m53menlo.dts
+++ b/arch/arm/boot/dts/imx53-m53menlo.dts
@@ -64,6 +64,12 @@
 		};
 	};
 
+	beeper {
+		compatible = "gpio-beeper";
+		pinctrl-0 = <&pinctrl_beeper>;
+		gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>;
+	};
+
 	reg_usbh1_vbus: regulator-usbh1-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "vbus";
@@ -181,6 +187,12 @@
 			>;
 		};
 
+		pinctrl_beeper: beepergrp {
+			fsl,pins = <
+				MX53_PAD_CSI0_DAT17__GPIO6_3		0x1c4
+			>;
+		};
+
 		pinctrl_can1: can1grp {
 			fsl,pins = <
 				MX53_PAD_GPIO_7__CAN1_TXCAN		0x1c4
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V2 7/8] ARM: dts: imx53: Add GPIO line names on M53Menlo

[Marek Vasut]

Add meaningful GPIO line names for the board GPIOs.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
 arch/arm/boot/dts/imx53-m53menlo.dts | 72 ++++++++++++++++++++++++++++
 1 file changed, 72 insertions(+)

diff --git a/arch/arm/boot/dts/imx53-m53menlo.dts b/arch/arm/boot/dts/imx53-m53menlo.dts
index 39a76a5bbd19..a106233d1651 100644
--- a/arch/arm/boot/dts/imx53-m53menlo.dts
+++ b/arch/arm/boot/dts/imx53-m53menlo.dts
@@ -116,6 +116,78 @@
 	status = "okay";
 };
 
+&gpio1 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"TestPin_SV2_3", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"CPLD_JTAG_TDI", "CPLD_JTAG_TMS", "", "",
+		"", "CPLD_JTAG_TDO", "", "";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "CPLD_JTAG_TCK", "KBD_intK",
+		"CPLD_int", "CPLD_JTAG_internal", "CPLD_D[0]", "CPLD_D[1]",
+		"CPLD_D[2]", "CPLD_D[3]", "CPLD_D[4]", "CPLD_D[5]",
+		"CPLD_D[6]", "CPLD_D[7]", "DISP_reset", "KBD_intI";
+};
+
+&gpio6 {
+	gpio-line-names =
+		"", "", "", "",
+		"CPLD_reset", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+};
+
+&gpio7 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "USB-OTG_OverCurrent", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+};
+
 &i2c1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c1>;
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V2 8/8] ARM: dts: imx53: Update pinmux settings on M53Menlo

[Marek Vasut]

Update pinmux settings according to hardware team input.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
 arch/arm/boot/dts/imx53-m53menlo.dts | 87 ++++++++++++++++------------
 1 file changed, 49 insertions(+), 38 deletions(-)

diff --git a/arch/arm/boot/dts/imx53-m53menlo.dts b/arch/arm/boot/dts/imx53-m53menlo.dts
index a106233d1651..55c122a64ef0 100644
--- a/arch/arm/boot/dts/imx53-m53menlo.dts
+++ b/arch/arm/boot/dts/imx53-m53menlo.dts
@@ -235,27 +235,31 @@
 	imx53-m53evk {
 		hoggrp {
 			fsl,pins = <
-				MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK	0x1c4
-				MX53_PAD_EIM_EB3__GPIO2_31		0x1d5
-				MX53_PAD_PATA_DA_0__GPIO7_6		0x1d5
-				MX53_PAD_GPIO_19__CCM_CLKO		0x1d5
-				MX53_PAD_CSI0_MCLK__CCM_CSI0_MCLK	0x1d5
-				MX53_PAD_CSI0_DAT4__GPIO5_22		0x1d5
-				MX53_PAD_CSI0_DAT5__GPIO5_23		0x1d5
-				MX53_PAD_CSI0_DAT6__GPIO5_24		0x1d5
-				MX53_PAD_CSI0_DAT7__GPIO5_25		0x1d5
-				MX53_PAD_CSI0_DAT8__GPIO5_26		0x1d5
-				MX53_PAD_CSI0_DAT9__GPIO5_27		0x1d5
-				MX53_PAD_CSI0_DAT10__GPIO5_28		0x1d5
-				MX53_PAD_CSI0_DAT11__GPIO5_29		0x1d5
-				MX53_PAD_CSI0_DAT14__GPIO6_0		0x1d5
+				MX53_PAD_GPIO_19__CCM_CLKO		0x1e4
+				MX53_PAD_CSI0_DATA_EN__GPIO5_20		0x1e4
+				MX53_PAD_CSI0_DAT4__GPIO5_22		0x1e4
+				MX53_PAD_CSI0_DAT5__GPIO5_23		0x1c4
+				MX53_PAD_CSI0_DAT6__GPIO5_24		0x1e4
+				MX53_PAD_CSI0_DAT7__GPIO5_25		0x1e4
+				MX53_PAD_CSI0_DAT8__GPIO5_26		0x1e4
+				MX53_PAD_CSI0_DAT9__GPIO5_27		0x1c4
+				MX53_PAD_CSI0_DAT10__GPIO5_28		0x1e4
+				MX53_PAD_CSI0_DAT11__GPIO5_29		0x1e4
+				MX53_PAD_PATA_DATA11__GPIO2_11		0x1e4
+				MX53_PAD_EIM_D24__GPIO3_24		0x1e4
+				MX53_PAD_EIM_D25__GPIO3_25		0x1e4
+				MX53_PAD_EIM_D29__GPIO3_29		0x1e4
+				MX53_PAD_CSI0_PIXCLK__GPIO5_18		0x1e4
+				MX53_PAD_CSI0_VSYNC__GPIO5_21		0x1e4
+				MX53_PAD_CSI0_DAT18__GPIO6_4		0x1c4
+				MX53_PAD_PATA_DATA8__GPIO2_8		0x1e4
 			>;
 		};
 
 		pinctrl_led: ledgrp {
 			fsl,pins = <
-				MX53_PAD_CSI0_DAT15__GPIO6_1		0x1d5
-				MX53_PAD_CSI0_DAT16__GPIO6_2		0x1d5
+				MX53_PAD_CSI0_DAT15__GPIO6_1		0x1c4
+				MX53_PAD_CSI0_DAT16__GPIO6_2		0x1c4
 			>;
 		};
 
@@ -274,49 +278,56 @@
 
 		pinctrl_can2: can2grp {
 			fsl,pins = <
-				MX53_PAD_KEY_COL4__CAN2_TXCAN		0x1c4
+				MX53_PAD_KEY_COL4__CAN2_TXCAN		0x1e4
 				MX53_PAD_KEY_ROW4__CAN2_RXCAN		0x1c4
 			>;
 		};
 
 		pinctrl_display_gpio: display-gpiogrp {
 			fsl,pins = <
-				MX53_PAD_CSI0_DAT12__GPIO5_30		0x1d5 /* Reset */
-				MX53_PAD_CSI0_DAT13__GPIO5_31		0x1d5 /* Interrupt */
+				MX53_PAD_CSI0_DAT12__GPIO5_30		0x1c4 /* Reset */
+				MX53_PAD_CSI0_MCLK__GPIO5_19		0x1e4 /* Int-K */
+				MX53_PAD_CSI0_DAT13__GPIO5_31		0x1c4 /* Int-I */
+
+				MX53_PAD_CSI0_DAT14__GPIO6_0		0x1c4 /* Power down */
 			>;
 		};
 
 		pinctrl_edt_ft5x06: edt-ft5x06grp {
 			fsl,pins = <
-				MX53_PAD_PATA_DATA9__GPIO2_9		0x1d5 /* Reset */
-				MX53_PAD_CSI0_DAT19__GPIO6_5		0x1d5 /* Interrupt */
-				MX53_PAD_PATA_DATA10__GPIO2_10		0x1d5 /* Wake */
+				MX53_PAD_PATA_DATA9__GPIO2_9		0x1e4 /* Reset */
+				MX53_PAD_CSI0_DAT19__GPIO6_5		0x1c4 /* Interrupt */
+				MX53_PAD_PATA_DATA10__GPIO2_10		0x1e4 /* Wake */
 			>;
 		};
 
 		pinctrl_esdhc1: esdhc1grp {
 			fsl,pins = <
-				MX53_PAD_SD1_DATA0__ESDHC1_DAT0		0x1d5
-				MX53_PAD_SD1_DATA1__ESDHC1_DAT1		0x1d5
-				MX53_PAD_SD1_DATA2__ESDHC1_DAT2		0x1d5
-				MX53_PAD_SD1_DATA3__ESDHC1_DAT3		0x1d5
-				MX53_PAD_SD1_CMD__ESDHC1_CMD		0x1d5
-				MX53_PAD_SD1_CLK__ESDHC1_CLK		0x1d5
+				MX53_PAD_SD1_DATA0__ESDHC1_DAT0		0x1e4
+				MX53_PAD_SD1_DATA1__ESDHC1_DAT1		0x1e4
+				MX53_PAD_SD1_DATA2__ESDHC1_DAT2		0x1e4
+				MX53_PAD_SD1_DATA3__ESDHC1_DAT3		0x1e4
+				MX53_PAD_SD1_CMD__ESDHC1_CMD		0x1e4
+				MX53_PAD_SD1_CLK__ESDHC1_CLK		0x1e4
+				MX53_PAD_GPIO_1__GPIO1_1		0x1c4
+				MX53_PAD_GPIO_9__GPIO1_9		0x1e4
 			>;
 		};
 
 		pinctrl_fec: fecgrp {
 			fsl,pins = <
-				MX53_PAD_FEC_MDC__FEC_MDC		0x4
-				MX53_PAD_FEC_MDIO__FEC_MDIO		0x1fc
-				MX53_PAD_FEC_REF_CLK__FEC_TX_CLK	0x180
-				MX53_PAD_FEC_RX_ER__FEC_RX_ER		0x180
-				MX53_PAD_FEC_CRS_DV__FEC_RX_DV		0x180
-				MX53_PAD_FEC_RXD1__FEC_RDATA_1		0x180
-				MX53_PAD_FEC_RXD0__FEC_RDATA_0		0x180
-				MX53_PAD_FEC_TX_EN__FEC_TX_EN		0x4
-				MX53_PAD_FEC_TXD1__FEC_TDATA_1		0x4
-				MX53_PAD_FEC_TXD0__FEC_TDATA_0		0x4
+				MX53_PAD_FEC_MDC__FEC_MDC		0x1e4
+				MX53_PAD_FEC_MDIO__FEC_MDIO		0x1e4
+				MX53_PAD_FEC_REF_CLK__FEC_TX_CLK	0x1e4
+				MX53_PAD_FEC_RX_ER__FEC_RX_ER		0x1e4
+				MX53_PAD_FEC_CRS_DV__FEC_RX_DV		0x1e4
+				MX53_PAD_FEC_RXD1__FEC_RDATA_1		0x1e4
+				MX53_PAD_FEC_RXD0__FEC_RDATA_0		0x1e4
+				MX53_PAD_FEC_TX_EN__FEC_TX_EN		0x1c4
+				MX53_PAD_FEC_TXD1__FEC_TDATA_1		0x1e4
+				MX53_PAD_FEC_TXD0__FEC_TDATA_0		0x1e4
+				MX53_PAD_PATA_DA_1__GPIO7_7		0x1e4
+				MX53_PAD_EIM_EB3__GPIO2_31		0x1e4
 			>;
 		};
 
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH V2 1/8] ARM: dts: imx53: Update UART configuration on M53Menlo

[Fabio Estevam]

On Wed, May 15, 2019 at 7:46 PM Marek Vasut <marex@denx.de> wrote:
>
> Enable flow control lines on UART1 and UART2, add matching pinmux entries.
> Add and enable UART3 with RS485 mode enabled on boot.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Shawn Guo <shawnguo@kernel.org>
> Cc: Fabio Estevam <festevam@gmail.com>
> Cc: NXP Linux Team <linux-imx@nxp.com>
> To: linux-arm-kernel@lists.infradead.org

For the series:

Reviewed-by: Fabio Estevam <festevam@gmail.com>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH V2 1/8] ARM: dts: imx53: Update UART configuration on M53Menlo

[Shawn Guo]

On Thu, May 16, 2019 at 12:45:54AM +0200, Marek Vasut wrote:
> Enable flow control lines on UART1 and UART2, add matching pinmux entries.
> Add and enable UART3 with RS485 mode enabled on boot.
> 
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Shawn Guo <shawnguo@kernel.org>
> Cc: Fabio Estevam <festevam@gmail.com>
> Cc: NXP Linux Team <linux-imx@nxp.com>
> To: linux-arm-kernel@lists.infradead.org

Applied all, thanks.

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel