[PATCH net-next v5 0/3] net: phy: mdio: add IPQ40xx MDIO support

[PATCH net-next v5 0/3] net: phy: mdio: add IPQ40xx MDIO support

[Robert Marko]

This patch series provides support for the IPQ40xx built-in MDIO interface.
Included are driver, devicetree bindings for it and devicetree node.

Robert Marko (3):
  net: phy: mdio: add IPQ4019 MDIO driver
  dt-bindings: add Qualcomm IPQ4019 MDIO bindings
  ARM: dts: qcom: ipq4019: add MDIO node

 .../bindings/net/qcom,ipq4019-mdio.yaml       |  61 +++++++
 arch/arm/boot/dts/qcom-ipq4019.dtsi           |  28 +++
 drivers/net/phy/Kconfig                       |   7 +
 drivers/net/phy/Makefile                      |   1 +
 drivers/net/phy/mdio-ipq4019.c                | 160 ++++++++++++++++++
 5 files changed, 257 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml
 create mode 100644 drivers/net/phy/mdio-ipq4019.c

-- 
2.26.2

[PATCH net-next v5 1/3] net: phy: mdio: add IPQ4019 MDIO driver

[Robert Marko]

This patch adds the driver for the MDIO interface
inside of Qualcomm IPQ40xx series SoC-s.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
---
Changes from v3 to v4:
* Change compatible	and references to IPQ4019
  per Rob Herrings suggestion

Changes from v2 to v3:
* Rename registers
* Remove unnecessary variable initialisations
* Switch to readl_poll_timeout() instead of custom solution
* Drop unused header

Changes from v1 to v2:
* Remove magic default value
* Remove lockdep_assert_held
* Add C45 check
* Simplify the driver
* Drop device and mii_bus structs from private struct
* Use devm_mdiobus_alloc_size()

 drivers/net/phy/Kconfig        |   7 ++
 drivers/net/phy/Makefile       |   1 +
 drivers/net/phy/mdio-ipq4019.c | 160 +++++++++++++++++++++++++++++++++
 3 files changed, 168 insertions(+)
 create mode 100644 drivers/net/phy/mdio-ipq4019.c

diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 3fa33d27eeba..6693df126861 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -157,6 +157,13 @@ config MDIO_I2C
 
 	  This is library mode.
 
+config MDIO_IPQ4019
+	tristate "Qualcomm IPQ4019 MDIO interface support"
+	depends on HAS_IOMEM && OF_MDIO
+	help
+	  This driver supports the MDIO interface found in Qualcomm
+	  IPQ40xx series Soc-s.
+
 config MDIO_IPQ8064
 	tristate "Qualcomm IPQ8064 MDIO interface support"
 	depends on HAS_IOMEM && OF_MDIO
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index 2f5c7093a65b..12e0d0b137b9 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -37,6 +37,7 @@ obj-$(CONFIG_MDIO_CAVIUM)	+= mdio-cavium.o
 obj-$(CONFIG_MDIO_GPIO)		+= mdio-gpio.o
 obj-$(CONFIG_MDIO_HISI_FEMAC)	+= mdio-hisi-femac.o
 obj-$(CONFIG_MDIO_I2C)		+= mdio-i2c.o
+obj-$(CONFIG_MDIO_IPQ4019)	+= mdio-ipq4019.o
 obj-$(CONFIG_MDIO_IPQ8064)	+= mdio-ipq8064.o
 obj-$(CONFIG_MDIO_MOXART)	+= mdio-moxart.o
 obj-$(CONFIG_MDIO_MSCC_MIIM)	+= mdio-mscc-miim.o
diff --git a/drivers/net/phy/mdio-ipq4019.c b/drivers/net/phy/mdio-ipq4019.c
new file mode 100644
index 000000000000..f1f25489e134
--- /dev/null
+++ b/drivers/net/phy/mdio-ipq4019.c
@@ -0,0 +1,160 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved. */
+/* Copyright (c) 2020 Sartura Ltd. */
+
+#include <linux/delay.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/of_address.h>
+#include <linux/of_mdio.h>
+#include <linux/phy.h>
+#include <linux/platform_device.h>
+
+#define MDIO_ADDR_REG				0x44
+#define MDIO_DATA_WRITE_REG			0x48
+#define MDIO_DATA_READ_REG			0x4c
+#define MDIO_CMD_REG				0x50
+#define MDIO_CMD_ACCESS_BUSY		BIT(16)
+#define MDIO_CMD_ACCESS_START		BIT(8)
+#define MDIO_CMD_ACCESS_CODE_READ	0
+#define MDIO_CMD_ACCESS_CODE_WRITE	1
+
+#define ipq4019_MDIO_TIMEOUT	10000
+#define ipq4019_MDIO_SLEEP		10
+
+struct ipq4019_mdio_data {
+	void __iomem	*membase;
+};
+
+static int ipq4019_mdio_wait_busy(struct mii_bus *bus)
+{
+	struct ipq4019_mdio_data *priv = bus->priv;
+	unsigned int busy;
+
+	return readl_poll_timeout(priv->membase + MDIO_CMD_REG, busy,
+				  (busy & MDIO_CMD_ACCESS_BUSY) == 0, 
+				  ipq4019_MDIO_SLEEP, ipq4019_MDIO_TIMEOUT);
+}
+
+static int ipq4019_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+	struct ipq4019_mdio_data *priv = bus->priv;
+	unsigned int cmd;
+
+	/* Reject clause 45 */
+	if (regnum & MII_ADDR_C45)
+		return -EOPNOTSUPP;
+
+	if (ipq4019_mdio_wait_busy(bus))
+		return -ETIMEDOUT;
+
+	/* issue the phy address and reg */
+	writel((mii_id << 8) | regnum, priv->membase + MDIO_ADDR_REG);
+
+	cmd = MDIO_CMD_ACCESS_START | MDIO_CMD_ACCESS_CODE_READ;
+
+	/* issue read command */
+	writel(cmd, priv->membase + MDIO_CMD_REG);
+
+	/* Wait read complete */
+	if (ipq4019_mdio_wait_busy(bus))
+		return -ETIMEDOUT;
+
+	/* Read and return data */
+	return readl(priv->membase + MDIO_DATA_READ_REG);
+}
+
+static int ipq4019_mdio_write(struct mii_bus *bus, int mii_id, int regnum,
+							 u16 value)
+{
+	struct ipq4019_mdio_data *priv = bus->priv;
+	unsigned int cmd;
+
+	/* Reject clause 45 */
+	if (regnum & MII_ADDR_C45)
+		return -EOPNOTSUPP;
+
+	if (ipq4019_mdio_wait_busy(bus))
+		return -ETIMEDOUT;
+
+	/* issue the phy address and reg */
+	writel((mii_id << 8) | regnum, priv->membase + MDIO_ADDR_REG);
+
+	/* issue write data */
+	writel(value, priv->membase + MDIO_DATA_WRITE_REG);
+
+	cmd = MDIO_CMD_ACCESS_START | MDIO_CMD_ACCESS_CODE_WRITE;
+	/* issue write command */
+	writel(cmd, priv->membase + MDIO_CMD_REG);
+
+	/* Wait write complete */
+	if (ipq4019_mdio_wait_busy(bus))
+		return -ETIMEDOUT;
+
+	return 0;
+}
+
+static int ipq4019_mdio_probe(struct platform_device *pdev)
+{
+	struct ipq4019_mdio_data *priv;
+	struct mii_bus *bus;
+	int ret;
+
+	bus = devm_mdiobus_alloc_size(&pdev->dev, sizeof(*priv));
+	if (!bus)
+		return -ENOMEM;
+
+	priv = bus->priv;
+
+	priv->membase = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(priv->membase))
+		return PTR_ERR(priv->membase);
+
+	bus->name = "ipq4019_mdio";
+	bus->read = ipq4019_mdio_read;
+	bus->write = ipq4019_mdio_write;
+	bus->parent = &pdev->dev;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s%d", pdev->name, pdev->id);
+
+	ret = of_mdiobus_register(bus, pdev->dev.of_node);
+	if (ret) {
+		dev_err(&pdev->dev, "Cannot register MDIO bus!\n");
+		return ret;
+	}
+
+	platform_set_drvdata(pdev, bus);
+
+	return 0;
+}
+
+static int ipq4019_mdio_remove(struct platform_device *pdev)
+{
+	struct mii_bus *bus = platform_get_drvdata(pdev);
+
+	mdiobus_unregister(bus);
+
+	return 0;
+}
+
+static const struct of_device_id ipq4019_mdio_dt_ids[] = {
+	{ .compatible = "qcom,ipq4019-mdio" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, ipq4019_mdio_dt_ids);
+
+static struct platform_driver ipq4019_mdio_driver = {
+	.probe = ipq4019_mdio_probe,
+	.remove = ipq4019_mdio_remove,
+	.driver = {
+		.name = "ipq4019-mdio",
+		.of_match_table = ipq4019_mdio_dt_ids,
+	},
+};
+
+module_platform_driver(ipq4019_mdio_driver);
+
+MODULE_DESCRIPTION("ipq4019 MDIO interface driver");
+MODULE_AUTHOR("Qualcomm Atheros");
+MODULE_LICENSE("Dual BSD/GPL");
-- 
2.26.2

[PATCH net-next v5 2/3] dt-bindings: add Qualcomm IPQ4019 MDIO bindings

[Robert Marko]

This patch adds the binding document for the IPQ40xx MDIO driver.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
---
Changes from v3 to v4:
* Change compatible to IPQ4019

Changes from v2 to v3:
* Remove status from example

 .../bindings/net/qcom,ipq4019-mdio.yaml       | 61 +++++++++++++++++++
 1 file changed, 61 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml

diff --git a/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml b/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml
new file mode 100644
index 000000000000..13555a89975f
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml
@@ -0,0 +1,61 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/qcom,ipq4019-mdio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm IPQ40xx MDIO Controller Device Tree Bindings
+
+maintainers:
+  - Robert Marko <robert.marko@sartura.hr>
+
+allOf:
+  - $ref: "mdio.yaml#"
+
+properties:
+  compatible:
+    const: qcom,ipq4019-mdio
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - "#address-cells"
+  - "#size-cells"
+
+examples:
+  - |
+    mdio@90000 {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      compatible = "qcom,ipq4019-mdio";
+      reg = <0x90000 0x64>;
+
+      ethphy0: ethernet-phy@0 {
+        reg = <0>;
+      };
+
+      ethphy1: ethernet-phy@1 {
+        reg = <1>;
+      };
+
+      ethphy2: ethernet-phy@2 {
+        reg = <2>;
+      };
+
+      ethphy3: ethernet-phy@3 {
+        reg = <3>;
+      };
+
+      ethphy4: ethernet-phy@4 {
+        reg = <4>;
+      };
+    };
-- 
2.26.2

[PATCH net-next v5 3/3] ARM: dts: qcom: ipq4019: add MDIO node

[Robert Marko]

This patch adds the necessary MDIO interface node
to the Qualcomm IPQ4019 DTSI.

Built-in QCA8337N switch is managed using it,
and since we have a driver for it lets add it.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
---
Changes from v4 to v5:
* Rebase to apply on net-next

Changes from v3 to v4:
* Change compatible to IPQ4019

Changes from v2 to v3:
* Correct commit title

 arch/arm/boot/dts/qcom-ipq4019.dtsi | 28 ++++++++++++++++++++++++++++
 1 file changed, 28 insertions(+)

diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi
index bfa9ce4c6e69..b9839f86e703 100644
--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
@@ -576,5 +576,33 @@ wifi1: wifi@a800000 {
 					  "legacy";
 			status = "disabled";
 		};
+
+		mdio: mdio@90000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "qcom,ipq4019-mdio";
+			reg = <0x90000 0x64>;
+			status = "disabled";
+
+			ethphy0: ethernet-phy@0 {
+				reg = <0>;
+			};
+
+			ethphy1: ethernet-phy@1 {
+				reg = <1>;
+			};
+
+			ethphy2: ethernet-phy@2 {
+				reg = <2>;
+			};
+
+			ethphy3: ethernet-phy@3 {
+				reg = <3>;
+			};
+
+			ethphy4: ethernet-phy@4 {
+				reg = <4>;
+			};
+		};
 	};
 };
-- 
2.26.2

Re: [PATCH net-next v5 0/3] net: phy: mdio: add IPQ40xx MDIO support

[David Miller]

From: Robert Marko <robert.marko@sartura.hr>
Date: Thu, 30 Apr 2020 11:07:04 +0200

> This patch series provides support for the IPQ40xx built-in MDIO interface.
> Included are driver, devicetree bindings for it and devicetree node.

Series applied, thanks.