Lost PCIe PME after a914ff2d78ce ("PCI/ASPM: Don't select CONFIG

All of lore.kernel.org
 help / color / mirror / Atom feed

* Lost PCIe PME after a914ff2d78ce ("PCI/ASPM: Don't select CONFIG_PCIEASPM by default")
@ 2020-05-28 21:44 Heiner Kallweit
  2020-05-29 18:50 ` Heiner Kallweit
  0 siblings, 1 reply; 15+ messages in thread
From: Heiner Kallweit @ 2020-05-28 21:44 UTC (permalink / raw)
  To: Bjorn Helgaas; +Cc: linux-pci

For whatever reason with this change (and losing ASPM control) I also
loose the PCIe PME interrupts. This prevents my network card from
resuming from runtime-suspend.
Reverting the change brings back ASPM control and the PCIe PME irq's.

Affected system is a Zotac MiniPC with a N3450 CPU:
PCI bridge: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series PCI Express Port A #1 (rev fb)

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: Lost PCIe PME after a914ff2d78ce ("PCI/ASPM: Don't select CONFIG_PCIEASPM by default")
  2020-05-28 21:44 Lost PCIe PME after a914ff2d78ce ("PCI/ASPM: Don't select CONFIG_PCIEASPM by default") Heiner Kallweit
@ 2020-05-29 18:50 ` Heiner Kallweit
  2020-05-29 19:21   ` Bjorn Helgaas
  0 siblings, 1 reply; 15+ messages in thread
From: Heiner Kallweit @ 2020-05-29 18:50 UTC (permalink / raw)
  To: Bjorn Helgaas; +Cc: linux-pci

On 28.05.2020 23:44, Heiner Kallweit wrote:
> For whatever reason with this change (and losing ASPM control) I also
> loose the PCIe PME interrupts. This prevents my network card from
> resuming from runtime-suspend.
> Reverting the change brings back ASPM control and the PCIe PME irq's.
> 
> Affected system is a Zotac MiniPC with a N3450 CPU:
> PCI bridge: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series PCI Express Port A #1 (rev fb)
> 
I checked a little bit further and w/o ASPM control the root ports
don't have the PME service bit set in their capabilities.
Not sure whether this is a chipset bug or whether there's a better
explanation. However more chipsets may have such a behavior.

W/o the "default y" for ASPM control we also have the situation now
that the config option description says "When in doubt, say Y."
but it takes the EXPERT mode to enable it. This seems to be a little
bit inconsistent.

To cut a long story short:
At least on some systems this change has unwanted side effects.

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: Lost PCIe PME after a914ff2d78ce ("PCI/ASPM: Don't select CONFIG_PCIEASPM by default")
  2020-05-29 18:50 ` Heiner Kallweit
@ 2020-05-29 19:21   ` Bjorn Helgaas
  2020-05-29 19:40     ` Heiner Kallweit
  0 siblings, 1 reply; 15+ messages in thread
From: Bjorn Helgaas @ 2020-05-29 19:21 UTC (permalink / raw)
  To: Heiner Kallweit; +Cc: Bjorn Helgaas, linux-pci, Rafael J. Wysocki, linux-kernel

[+cc Rafael, linux-kernel]

On Fri, May 29, 2020 at 08:50:46PM +0200, Heiner Kallweit wrote:
> On 28.05.2020 23:44, Heiner Kallweit wrote:
> > For whatever reason with this change (and losing ASPM control) I also
> > loose the PCIe PME interrupts. This prevents my network card from
> > resuming from runtime-suspend.
> > Reverting the change brings back ASPM control and the PCIe PME irq's.
> > 
> > Affected system is a Zotac MiniPC with a N3450 CPU:
> > PCI bridge: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series PCI Express Port A #1 (rev fb)
> > 
> I checked a little bit further and w/o ASPM control the root ports
> don't have the PME service bit set in their capabilities.
> Not sure whether this is a chipset bug or whether there's a better
> explanation. However more chipsets may have such a behavior.

Hmm.  Is the difference simply changing the PCIEASPM config symbol, or
are you booting with command-line arguments like "pcie_aspm=off"?

What's the specific PME bit that changes in the root ports?  Can you
collect the "sudo lspci -vvxxxx" output with and without ASPM?

The capability bits are generally read-only as far as the PCI spec is
concerned, but devices have implementation-specific knobs that the
BIOS may use to change things.  Without CONFIG_PCIEASPM, Linux will
not request control of LTR, and that could cause the BIOS to change
something.  You should be able to see the LTR control difference in
the dmesg logging about _OSC.

> W/o the "default y" for ASPM control we also have the situation now
> that the config option description says "When in doubt, say Y."
> but it takes the EXPERT mode to enable it. This seems to be a little
> bit inconsistent.

We should probably remove the "if EXPERT" from the PCIEASPM kconfig.
But I would expect PME to work correctly regardless of PCIEASPM, so
removing "if EXPERT" doesn't solve the underlying problem.

Rafael, does this ring any bells for you?  I don't remember a
connection between PME and ASPM, but maybe there is one.

> To cut a long story short:
> At least on some systems this change has unwanted side effects.

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: Lost PCIe PME after a914ff2d78ce ("PCI/ASPM: Don't select CONFIG_PCIEASPM by default")
  2020-05-29 19:21   ` Bjorn Helgaas
@ 2020-05-29 19:40     ` Heiner Kallweit
  2020-05-29 20:09       ` Heiner Kallweit
  0 siblings, 1 reply; 15+ messages in thread
From: Heiner Kallweit @ 2020-05-29 19:40 UTC (permalink / raw)
  To: Bjorn Helgaas; +Cc: Bjorn Helgaas, linux-pci, Rafael J. Wysocki, linux-kernel

[-- Attachment #1: Type: text/plain, Size: 2944 bytes --]

On 29.05.2020 21:21, Bjorn Helgaas wrote:
> [+cc Rafael, linux-kernel]
> 
> On Fri, May 29, 2020 at 08:50:46PM +0200, Heiner Kallweit wrote:
>> On 28.05.2020 23:44, Heiner Kallweit wrote:
>>> For whatever reason with this change (and losing ASPM control) I also
>>> loose the PCIe PME interrupts. This prevents my network card from
>>> resuming from runtime-suspend.
>>> Reverting the change brings back ASPM control and the PCIe PME irq's.
>>>
>>> Affected system is a Zotac MiniPC with a N3450 CPU:
>>> PCI bridge: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series PCI Express Port A #1 (rev fb)
>>>
>> I checked a little bit further and w/o ASPM control the root ports
>> don't have the PME service bit set in their capabilities.
>> Not sure whether this is a chipset bug or whether there's a better
>> explanation. However more chipsets may have such a behavior.
> 
> Hmm.  Is the difference simply changing the PCIEASPM config symbol, or
> are you booting with command-line arguments like "pcie_aspm=off"?
> 
Only difference is the config symbol. My command line is plain and simple:

Command line: initrd=\intel-ucode.img initrd=\initramfs-linux.img root=/dev/sda2 rw

> What's the specific PME bit that changes in the root ports?  Can you
> collect the "sudo lspci -vvxxxx" output with and without ASPM?
> 
> The capability bits are generally read-only as far as the PCI spec is
> concerned, but devices have implementation-specific knobs that the
> BIOS may use to change things.  Without CONFIG_PCIEASPM, Linux will
> not request control of LTR, and that could cause the BIOS to change
> something.  You should be able to see the LTR control difference in
> the dmesg logging about _OSC.
> 
>> W/o the "default y" for ASPM control we also have the situation now
>> that the config option description says "When in doubt, say Y."
>> but it takes the EXPERT mode to enable it. This seems to be a little
>> bit inconsistent.
> 
> We should probably remove the "if EXPERT" from the PCIEASPM kconfig.
> But I would expect PME to work correctly regardless of PCIEASPM, so
> removing "if EXPERT" doesn't solve the underlying problem.
> 
> Rafael, does this ring any bells for you?  I don't remember a
> connection between PME and ASPM, but maybe there is one.
> 
>> To cut a long story short:
>> At least on some systems this change has unwanted side effects.

lspci output w/ and w/o ASPM is attached incl. a diff.
Here comes the _OSC difference.

w/o ASPM

[    0.386063] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig Segments MSI HPX-Type3]
[    0.386918] acpi PNP0A08:00: _OSC: not requesting OS control; OS requires [ExtendedConfig ASPM ClockPM MSI]

w/ ASPM
[    0.388141] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3]
[    0.393648] acpi PNP0A08:00: _OSC: OS now controls [PME AER PCIeCapability LTR]

It's at least interesting that w/o ASPM OS doesn't control PME and AER.

[-- Attachment #2: lspci.diff --]
[-- Type: text/plain, Size: 4268 bytes --]

--- lspci_vvxxx_w_aspm	2020-05-29 21:29:22.274931378 +0200
+++ lspci_vvxxx_wo_aspm	2020-05-29 21:26:06.536601482 +0200
@@ -25,7 +25,7 @@
 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
 	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
 	Latency: 0
-	Interrupt: pin A routed to IRQ 128
+	Interrupt: pin A routed to IRQ 127
 	Region 0: Memory at 90000000 (64-bit, non-prefetchable) [size=16M]
 	Region 2: Memory at 80000000 (64-bit, prefetchable) [size=256M]
 	Region 4: I/O ports at f000 [size=64]
@@ -49,7 +49,7 @@
 		Address: fee08004  Data: 4023
 	Capabilities: [d0] Power Management version 2
 		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
-		Status: D3 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
+		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
 	Capabilities: [100 v1] Process Address Space ID (PASID)
 		PASIDCap: Exec+ Priv-, Max PASID Width: 14
 		PASIDCtl: Enable- Exec- Priv-
@@ -75,7 +75,7 @@
 a0: 00 00 00 00 00 00 00 00 00 00 00 00 05 d0 01 00
 b0: 04 80 e0 fe 23 40 00 00 00 00 00 00 00 00 00 00
 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
-d0: 01 00 22 00 03 00 00 00 00 00 00 00 00 00 00 00
+d0: 01 00 22 00 00 00 00 00 00 00 00 00 00 00 00 00
 e0: 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00 00
 f0: 00 00 00 00 00 00 00 00 00 00 00 00 18 40 b7 79
 
@@ -218,7 +218,7 @@
 		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
 			Changed: MRL- PresDet- LinkState+
 		RootCap: CRSVisible-
-		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
+		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
 		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
 		DevCap2: Completion Timeout: Range ABC, TimeoutDis+, NROPrPrP-, LTR+
 			 10BitTagComp-, 10BitTagReq-, OBFF Not Supported, ExtFmt-, EETLPPrefix-
@@ -250,7 +250,7 @@
 20: 30 91 30 91 f1 ff 01 00 00 00 00 00 00 00 00 00
 30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 12 00
 40: 10 80 42 01 01 80 00 00 00 00 10 00 12 40 71 03
-50: 40 00 11 70 00 b2 14 00 00 00 40 01 08 00 00 00
+50: 40 00 11 70 00 b2 14 00 00 00 40 01 00 00 00 00
 60: 00 00 00 00 37 08 00 00 00 04 00 00 06 00 00 00
 70: 42 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
 80: 05 90 01 00 04 40 e0 fe 21 40 00 00 00 00 00 00
@@ -294,7 +294,7 @@
 		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
 			Changed: MRL- PresDet- LinkState+
 		RootCap: CRSVisible-
-		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
+		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
 		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
 		DevCap2: Completion Timeout: Range ABC, TimeoutDis+, NROPrPrP-, LTR+
 			 10BitTagComp-, 10BitTagReq-, OBFF Not Supported, ExtFmt-, EETLPPrefix-
@@ -326,7 +326,7 @@
 20: 20 91 20 91 f1 ff 01 00 00 00 00 00 00 00 00 00
 30: 00 00 00 00 40 00 00 00 00 00 00 00 07 03 12 00
 40: 10 80 42 01 01 80 00 00 00 00 10 00 12 40 71 05
-50: 40 00 11 70 00 b2 24 00 00 00 40 01 08 00 00 00
+50: 40 00 11 70 00 b2 24 00 00 00 40 01 00 00 00 00
 60: 00 00 00 00 37 08 00 00 00 04 00 00 06 00 00 00
 70: 42 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
 80: 05 90 01 00 04 80 e0 fe 21 40 00 00 00 00 00 00
@@ -370,7 +370,7 @@
 		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
 			Changed: MRL- PresDet- LinkState+
 		RootCap: CRSVisible-
-		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
+		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
 		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
 		DevCap2: Completion Timeout: Range ABC, TimeoutDis+, NROPrPrP-, LTR+
 			 10BitTagComp-, 10BitTagReq-, OBFF Not Supported, ExtFmt-, EETLPPrefix-
@@ -402,7 +402,7 @@
 20: 10 91 10 91 f1 ff 01 00 00 00 00 00 00 00 00 00
 30: 00 00 00 00 40 00 00 00 00 00 00 00 ff 02 12 00
 40: 10 80 42 01 01 80 00 00 00 00 10 00 12 40 71 02
-50: 40 00 11 70 00 b2 0c 00 00 00 40 01 08 00 00 00
+50: 40 00 11 70 00 b2 0c 00 00 00 40 01 00 00 00 00
 60: 00 00 00 00 37 08 00 00 00 04 00 00 06 00 00 00
 70: 42 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
 80: 05 90 01 00 04 10 e0 fe 21 40 00 00 00 00 00 00

[-- Attachment #3: lspci_vvxxx_w_aspm --]
[-- Type: text/plain, Size: 46288 bytes --]

00:00.0 Host bridge: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series Host Bridge (rev 0b)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
00: 86 80 f0 5a 07 00 00 00 0b 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00
40: 00 00 00 00 00 00 00 00 01 00 d1 fe 00 00 00 00
50: c1 02 00 00 11 00 00 00 07 00 f0 7f 00 00 00 00
60: 01 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 80 01 00 00 00
b0: 01 00 00 7c 01 00 80 7b 01 00 00 7b 01 00 00 80
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 10 38 00 00
e0: 09 00 0c 01 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 0f 1c 01 00 00 00 00 00 00 00 00

00:02.0 VGA compatible controller: Intel Corporation HD Graphics 500 (rev 0b) (prog-if 00 [VGA controller])
	DeviceName:  Onboard IGD
	Subsystem: ZOTAC International (MCO) Ltd. HD Graphics 500
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 128
	Region 0: Memory at 90000000 (64-bit, non-prefetchable) [size=16M]
	Region 2: Memory at 80000000 (64-bit, prefetchable) [size=256M]
	Region 4: I/O ports at f000 [size=64]
	Expansion ROM at 000c0000 [virtual] [disabled] [size=128K]
	Capabilities: [40] Vendor Specific Information: Len=0c <?>
	Capabilities: [70] Express (v2) Root Complex Integrated Endpoint, MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0
			ExtTag- RBE+ FLReset+
		DevCtl:	CorrErr- NonFatalErr- FatalErr- UnsupReq-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- FLReset-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
		DevCap2: Completion Timeout: Not Supported, TimeoutDis-, NROPrPrP-, LTR-
			 10BitTagComp-, 10BitTagReq-, OBFF Not Supported, ExtFmt-, EETLPPrefix-
			 EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
			 FRS-
			 AtomicOpsCap: 32bit- 64bit- 128bitCAS-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
			 AtomicOpsCtl: ReqEn-
	Capabilities: [ac] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee08004  Data: 4023
	Capabilities: [d0] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D3 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [100 v1] Process Address Space ID (PASID)
		PASIDCap: Exec+ Priv-, Max PASID Width: 14
		PASIDCtl: Enable- Exec- Priv-
	Capabilities: [200 v1] Address Translation Service (ATS)
		ATSCap:	Invalidate Queue Depth: 00
		ATSCtl:	Enable-, Smallest Translation Unit: 00
	Capabilities: [300 v1] Page Request Interface (PRI)
		PRICtl: Enable- Reset-
		PRISta: RF- UPRGI- Stopped-
		Page Request Capacity: 00008000, Page Request Allocation: 00000000
	Kernel driver in use: i915
	Kernel modules: i915
00: 86 80 85 5a 07 04 10 00 0b 00 00 03 00 00 00 00
10: 04 00 00 90 00 00 00 00 0c 00 00 80 00 00 00 00
20: 01 f0 00 00 00 00 00 00 00 00 00 00 da 19 25 b3
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 00 00
40: 09 70 0c 01 00 00 00 00 00 00 00 00 00 00 00 00
50: c1 02 00 00 11 00 00 00 00 00 00 00 01 00 00 7c
60: 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 10 ac 92 00 00 80 00 10 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 05 d0 01 00
b0: 04 80 e0 fe 23 40 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 01 00 22 00 03 00 00 00 00 00 00 00 00 00 00 00
e0: 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 18 40 b7 79

00:0e.0 Audio device: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series Audio Cluster (rev 0b)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 129
	Region 0: Memory at 91410000 (64-bit, non-prefetchable) [size=16K]
	Region 4: Memory at 91000000 (64-bit, non-prefetchable) [size=1M]
	Capabilities: [50] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D3 NoSoftRst+ PME-Enable+ DSel=0 DScale=0 PME-
	Capabilities: [80] Vendor Specific Information: Len=14 <?>
	Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
		Address: 00000000fee01004  Data: 4023
	Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0
			ExtTag- RBE- FLReset+
		DevCtl:	CorrErr- NonFatalErr- FatalErr- UnsupReq-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- FLReset-
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
	Kernel driver in use: snd_hda_intel
	Kernel modules: snd_hda_intel
00: 86 80 98 5a 06 04 10 00 0b 00 03 04 00 00 00 00
10: 04 00 41 91 00 00 00 00 00 00 00 00 00 00 00 00
20: 04 00 00 91 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 19 01 00 00
40: 00 00 00 00 00 00 00 00 ff 0d 7b 80 00 00 00 00
50: 01 80 43 c8 0b 01 00 00 00 00 00 00 00 00 00 00
60: 05 70 81 00 04 10 e0 fe 00 00 00 00 23 40 00 00
70: 10 00 91 00 00 00 00 10 00 20 10 00 00 00 00 00
80: 09 60 14 f0 10 00 40 01 00 00 00 00 a1 04 01 00
90: 00 08 28 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 08 06 02 00 00 70 00 04 00 0c a5 82 10 00 03 00
d0: 00 00 30 00 10 00 03 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 1c 0f 00 01 00 00 00 00

00:0f.0 Communication controller: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series Trusted Execution Engine (rev 0b)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 125
	Region 0: Memory at 91421000 (64-bit, non-prefetchable) [size=4K]
	Capabilities: [50] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+
		Address: 00000000fee04004  Data: 4023
	Capabilities: [a4] Vendor Specific Information: Len=14 <?>
	Kernel driver in use: mei_me
	Kernel modules: mei_me
00: 86 80 9a 5a 06 04 10 00 0b 00 80 07 00 00 80 00
10: 04 10 42 91 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 07 01 00 00
40: 55 02 00 80 00 00 01 80 00 04 f4 09 00 00 00 00
50: 01 8c 03 40 08 00 00 00 00 00 00 00 00 00 00 00
60: 08 06 b5 30 00 00 08 00 00 00 00 00 00 00 00 00
70: 08 00 b5 c0 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 05 a4 81 00
90: 04 40 e0 fe 00 00 00 00 23 40 00 00 00 00 00 00
a0: 00 00 00 00 09 00 14 f0 10 00 40 01 00 00 00 00
b0: 01 80 00 00 38 0d 0e 00 00 00 00 00 00 00 00 40
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 1c 0f 00 01 00 00 00 00

00:12.0 SATA controller: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series SATA AHCI Controller (rev 0b) (prog-if 01 [AHCI 1.0])
	Subsystem: ZOTAC International (MCO) Ltd. Celeron N3350/Pentium N4200/Atom E3900 Series SATA AHCI Controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 124
	Region 0: Memory at 91414000 (32-bit, non-prefetchable) [size=8K]
	Region 1: Memory at 9141e000 (32-bit, non-prefetchable) [size=256]
	Region 2: I/O ports at f090 [size=8]
	Region 3: I/O ports at f080 [size=4]
	Region 4: I/O ports at f060 [size=32]
	Region 5: Memory at 9141d000 (32-bit, non-prefetchable) [size=2K]
	Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee08004  Data: 4022
	Capabilities: [70] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
		Status: D0 NoSoftRst+ PME-Enable+ DSel=0 DScale=0 PME-
	Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
	Kernel driver in use: ahci
	Kernel modules: ahci
00: 86 80 e3 5a 07 04 b0 02 0b 01 06 01 00 00 00 00
10: 00 40 41 91 00 e0 41 91 91 f0 00 00 81 f0 00 00
20: 61 f0 00 00 00 d0 41 91 00 00 00 00 da 19 25 b3
30: 00 00 00 00 80 00 00 00 00 00 00 00 03 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 01 a8 03 40 08 01 00 00 00 00 00 00 00 00 00 00
80: 05 70 01 00 04 80 e0 fe 22 40 00 00 00 00 00 00
90: 00 00 06 00 01 00 01 00 00 00 00 00 30 70 00 80
a0: 90 00 00 00 03 00 00 00 12 00 10 00 48 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 11 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 1c 0f 00 01 00 00 00 00

00:13.0 PCI bridge: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series PCI Express Port A #1 (rev fb) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 120
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: [disabled]
	Memory behind bridge: 91300000-913fffff [size=1M]
	Prefetchable memory behind bridge: [disabled]
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 256 bytes, PhantFunc 0
			ExtTag- RBE+
		DevCtl:	CorrErr- NonFatalErr- FatalErr- UnsupReq-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
		LnkCap:	Port #3, Speed 5GT/s, Width x1, ASPM not supported
			ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s (downgraded), Width x1 (ok)
			TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
			Slot #2, PowerLimit 10.000W; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
			Changed: MRL- PresDet- LinkState+
		RootCap: CRSVisible-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
		DevCap2: Completion Timeout: Range ABC, TimeoutDis+, NROPrPrP-, LTR+
			 10BitTagComp-, 10BitTagReq-, OBFF Not Supported, ExtFmt-, EETLPPrefix-
			 EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
			 FRS-, LN System CLS Not Supported, TPHComp-, ExtTPHComp-, ARIFwd+
			 AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled ARIFwd-
			 AtomicOpsCtl: ReqEn- EgressBlck-
		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee04004  Data: 4021
	Capabilities: [90] Subsystem: ZOTAC International (MCO) Ltd. Celeron N3350/Pentium N4200/Atom E3900 Series PCI Express Port A
	Capabilities: [a0] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [100 v0] Null
	Capabilities: [140 v1] Access Control Services
		ACSCap:	SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd- EgressCtrl- DirectTrans-
		ACSCtl:	SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
	Capabilities: [150 v0] Null
	Capabilities: [200 v0] Null
	Kernel driver in use: pcieport
00: 86 80 d8 5a 07 04 10 00 fb 00 04 06 00 00 81 00
10: 00 00 00 00 00 00 00 00 00 01 01 00 f0 00 00 20
20: 30 91 30 91 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 12 00
40: 10 80 42 01 01 80 00 00 00 00 10 00 12 40 71 03
50: 40 00 11 70 00 b2 14 00 00 00 40 01 08 00 00 00
60: 00 00 00 00 37 08 00 00 00 04 00 00 06 00 00 00
70: 42 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 90 01 00 04 40 e0 fe 21 40 00 00 00 00 00 00
90: 0d a0 00 00 da 19 25 b3 00 00 00 00 00 00 00 00
a0: 01 00 03 c8 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 77 90 00 00 42 1a 00 00 00 00 92 03 00 00 00 00
e0: 00 77 f3 00 00 00 00 00 16 80 03 00 00 00 00 00
f0: 50 07 00 00 00 07 00 40 1c 0f 00 01 04 00 00 01

00:13.2 PCI bridge: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series PCI Express Port A #3 (rev fb) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin C routed to IRQ 121
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	I/O behind bridge: 0000e000-0000efff [size=4K]
	Memory behind bridge: 91200000-912fffff [size=1M]
	Prefetchable memory behind bridge: [disabled]
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 256 bytes, PhantFunc 0
			ExtTag- RBE+
		DevCtl:	CorrErr- NonFatalErr- FatalErr- UnsupReq-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
		LnkCap:	Port #5, Speed 5GT/s, Width x1, ASPM not supported
			ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s (downgraded), Width x1 (ok)
			TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
			Slot #4, PowerLimit 10.000W; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
			Changed: MRL- PresDet- LinkState+
		RootCap: CRSVisible-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
		DevCap2: Completion Timeout: Range ABC, TimeoutDis+, NROPrPrP-, LTR+
			 10BitTagComp-, 10BitTagReq-, OBFF Not Supported, ExtFmt-, EETLPPrefix-
			 EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
			 FRS-, LN System CLS Not Supported, TPHComp-, ExtTPHComp-, ARIFwd+
			 AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled ARIFwd-
			 AtomicOpsCtl: ReqEn- EgressBlck-
		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee08004  Data: 4021
	Capabilities: [90] Subsystem: ZOTAC International (MCO) Ltd. Celeron N3350/Pentium N4200/Atom E3900 Series PCI Express Port A
	Capabilities: [a0] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [100 v0] Null
	Capabilities: [140 v1] Access Control Services
		ACSCap:	SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd- EgressCtrl- DirectTrans-
		ACSCtl:	SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
	Capabilities: [150 v0] Null
	Capabilities: [200 v0] Null
	Kernel driver in use: pcieport
00: 86 80 da 5a 07 04 10 00 fb 00 04 06 00 00 81 00
10: 00 00 00 00 00 00 00 00 00 02 02 00 e0 e0 00 20
20: 20 91 20 91 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 07 03 12 00
40: 10 80 42 01 01 80 00 00 00 00 10 00 12 40 71 05
50: 40 00 11 70 00 b2 24 00 00 00 40 01 08 00 00 00
60: 00 00 00 00 37 08 00 00 00 04 00 00 06 00 00 00
70: 42 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 90 01 00 04 80 e0 fe 21 40 00 00 00 00 00 00
90: 0d a0 00 00 da 19 25 b3 00 00 00 00 00 00 00 00
a0: 01 00 03 c8 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 77 10 00 00 42 1a 00 00 00 00 92 03 00 00 00 00
e0: 00 03 e3 00 00 00 00 00 16 00 01 00 00 00 00 00
f0: 50 07 00 00 00 04 00 4c 1c 0f 00 01 04 00 00 03

00:14.0 PCI bridge: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series PCI Express Port B #2 (rev fb) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 122
	Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
	I/O behind bridge: 0000d000-0000dfff [size=4K]
	Memory behind bridge: 91100000-911fffff [size=1M]
	Prefetchable memory behind bridge: [disabled]
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 256 bytes, PhantFunc 0
			ExtTag- RBE+
		DevCtl:	CorrErr- NonFatalErr- FatalErr- UnsupReq-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
		LnkCap:	Port #2, Speed 5GT/s, Width x1, ASPM not supported
			ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s (downgraded), Width x1 (ok)
			TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
			Slot #1, PowerLimit 10.000W; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
			Changed: MRL- PresDet- LinkState+
		RootCap: CRSVisible-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
		DevCap2: Completion Timeout: Range ABC, TimeoutDis+, NROPrPrP-, LTR+
			 10BitTagComp-, 10BitTagReq-, OBFF Not Supported, ExtFmt-, EETLPPrefix-
			 EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
			 FRS-, LN System CLS Not Supported, TPHComp-, ExtTPHComp-, ARIFwd+
			 AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled ARIFwd-
			 AtomicOpsCtl: ReqEn- EgressBlck-
		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee01004  Data: 4021
	Capabilities: [90] Subsystem: ZOTAC International (MCO) Ltd. Celeron N3350/Pentium N4200/Atom E3900 Series PCI Express Port B
	Capabilities: [a0] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [100 v0] Null
	Capabilities: [140 v1] Access Control Services
		ACSCap:	SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd- EgressCtrl- DirectTrans-
		ACSCtl:	SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
	Capabilities: [150 v0] Null
	Capabilities: [200 v0] Null
	Kernel driver in use: pcieport
00: 86 80 d7 5a 07 04 10 00 fb 00 04 06 00 00 81 00
10: 00 00 00 00 00 00 00 00 00 03 03 00 d0 d0 00 20
20: 10 91 10 91 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 ff 02 12 00
40: 10 80 42 01 01 80 00 00 00 00 10 00 12 40 71 02
50: 40 00 11 70 00 b2 0c 00 00 00 40 01 08 00 00 00
60: 00 00 00 00 37 08 00 00 00 04 00 00 06 00 00 00
70: 42 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 90 01 00 04 10 e0 fe 21 40 00 00 00 00 00 00
90: 0d a0 00 00 da 19 25 b3 00 00 00 00 00 00 00 00
a0: 01 00 03 c8 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 77 10 00 00 42 1a 00 00 00 00 92 03 00 00 00 00
e0: 00 03 e3 00 00 00 3c 88 16 00 01 00 00 00 00 00
f0: 50 07 00 00 00 04 00 4c 1c 0f 00 01 04 00 00 02

00:15.0 USB controller: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series USB xHCI (rev 0b) (prog-if 30 [XHCI])
	Subsystem: ZOTAC International (MCO) Ltd. Celeron N3350/Pentium N4200/Atom E3900 Series USB xHCI
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 123
	Region 0: Memory at 91400000 (64-bit, non-prefetchable) [size=64K]
	Capabilities: [70] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+
		Address: 00000000fee02004  Data: 4022
	Capabilities: [90] Vendor Specific Information: Len=14 <?>
	Kernel driver in use: xhci_hcd
00: 86 80 a8 5a 06 04 90 02 0b 30 03 0c 00 00 80 00
10: 04 00 40 91 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 da 19 25 b3
30: 00 00 00 00 70 00 00 00 00 00 00 00 11 01 00 00
40: fd 01 34 80 8f c6 cf 83 00 00 00 00 00 00 00 00
50: 5f 6e ce 0f 00 00 00 00 00 00 00 00 00 00 00 00
60: 30 60 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 01 80 c2 c1 08 00 00 00 00 00 00 00 00 00 00 00
80: 05 90 87 00 04 20 e0 fe 00 00 00 00 22 40 00 00
90: 09 00 14 f0 10 00 40 01 00 00 00 00 c1 0a 08 00
a0: 00 08 0e 00 00 18 00 00 8f 40 02 00 00 01 04 00
b0: 01 00 00 00 3e 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 01 00 00 00 3e 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 1c 0f 00 01 02 00 00 00

00:1a.0 Serial bus controller [0c80]: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series PWM Pin Controller (rev 0b)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 255
	Region 0: Memory at 9141c000 (64-bit, non-prefetchable) [size=4K]
	Region 2: Memory at 9141b000 (64-bit, non-prefetchable) [size=4K]
	Capabilities: [80] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [90] Vendor Specific Information: Len=14 <?>
00: 86 80 c8 5a 06 00 10 00 0b 00 80 0c 00 00 00 00
10: 04 c0 41 91 00 00 00 00 04 b0 41 91 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 ff 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 01 90 03 48 08 00 00 00 00 00 00 00 00 00 00 00
90: 09 00 14 f0 10 00 40 01 00 00 00 00 01 10 00 00
a0: 00 00 06 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 1c 0f 00 01 00 00 00 00

00:1c.0 SD Host controller: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series eMMC Controller (rev 0b) (prog-if 01)
	Subsystem: ZOTAC International (MCO) Ltd. Celeron N3350/Pentium N4200/Atom E3900 Series eMMC Controller
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 39
	Region 0: Memory at 9141a000 (64-bit, non-prefetchable) [size=4K]
	Region 2: Memory at 91419000 (64-bit, non-prefetchable) [size=4K]
	Capabilities: [80] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [90] Vendor Specific Information: Len=14 <?>
00: 86 80 cc 5a 06 00 10 00 0b 01 05 08 00 00 00 00
10: 04 a0 41 91 00 00 00 00 04 90 41 91 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 da 19 25 b3
30: 00 00 00 00 80 00 00 00 00 00 00 00 27 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 01 90 03 00 08 00 00 00 00 00 00 00 00 00 00 00
90: 09 00 14 f0 10 00 40 01 41 80 00 00 c1 81 00 00
a0: 00 08 2f 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 1c 0f 00 01 00 00 00 00

00:1e.0 SD Host controller: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series SDIO Controller (rev 0b) (prog-if 01)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 42
	Region 0: Memory at 91418000 (64-bit, non-prefetchable) [size=4K]
	Region 2: Memory at 91417000 (64-bit, non-prefetchable) [size=4K]
	Capabilities: [80] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [90] Vendor Specific Information: Len=14 <?>
00: 86 80 d0 5a 06 00 10 00 0b 01 05 08 00 00 00 00
10: 04 80 41 91 00 00 00 00 04 70 41 91 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 2a 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 01 90 03 00 08 00 00 00 00 00 00 00 00 00 00 00
90: 09 00 14 f0 10 00 40 01 41 80 00 00 c1 81 00 00
a0: 00 08 2f 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 1c 0f 00 01 00 00 00 00

00:1f.0 ISA bridge: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series Low Pin Count Interface (rev 0b)
	Subsystem: ZOTAC International (MCO) Ltd. Celeron N3350/Pentium N4200/Atom E3900 Series Low Pin Count Interface
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
00: 86 80 e8 5a 07 00 00 02 0b 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 da 19 25 b3
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 d0 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 0f 3f 81 00 0c 00 01 0a 3c 00 00 00 00 00
90: 00 00 00 00 00 0f 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 33 22 11 00 67 45 00 00 cf ff 00 00 80 00 00 00
e0: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 1c 0f 00 01 00 00 00 00

00:1f.1 SMBus: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series SMBus Controller (rev 0b)
	Subsystem: ZOTAC International (MCO) Ltd. Celeron N3350/Pentium N4200/Atom E3900 Series SMBus Controller
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin A routed to IRQ -2147483648
	Region 0: Memory at 91416000 (64-bit, non-prefetchable) [size=256]
	Region 4: I/O ports at f040 [size=32]
	Kernel driver in use: i801_smbus
	Kernel modules: i2c_i801
00: 86 80 d4 5a 03 00 80 02 0b 00 05 0c 00 00 00 00
10: 04 60 41 91 00 00 00 00 00 00 00 00 00 00 00 00
20: 41 f0 00 00 00 00 00 00 00 00 00 00 da 19 25 b3
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 01 00 00
40: 11 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 05 00 00 00 01 00 00 00 00 00 00 00 00 00 00
60: 03 04 04 00 00 00 08 08 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 24 00 04 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 1c 0f 00 01 00 00 00 00

01:00.0 Network controller: Intel Corporation Wireless 3165 (rev 81)
	Subsystem: Intel Corporation Dual Band Wireless AC 3165
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at 91300000 (64-bit, non-prefetchable) [disabled] [size=8K]
	Capabilities: [c8] Power Management version 3
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
		Address: 0000000000000000  Data: 0000
	Capabilities: [40] Express (v2) Endpoint, MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 unlimited
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ SlotPowerLimit 0.000W
		DevCtl:	CorrErr- NonFatalErr- FatalErr- UnsupReq-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr+ NoSnoop+ FLReset-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L1, Exit Latency L1 <32us
			ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk+
			ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s (ok), Width x1 (ok)
			TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		DevCap2: Completion Timeout: Range B, TimeoutDis+, NROPrPrP-, LTR+
			 10BitTagComp-, 10BitTagReq-, OBFF Via WAKE#, ExtFmt-, EETLPPrefix-
			 EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
			 FRS-, TPHComp-, ExtTPHComp-
			 AtomicOpsCap: 32bit- 64bit- 128bitCAS-
		DevCtl2: Completion Timeout: 16ms to 55ms, TimeoutDis-, LTR+, OBFF Disabled
			 AtomicOpsCtl: ReqEn-
		LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
		AERCap:	First Error Pointer: 00, ECRCGenCap- ECRCGenEn- ECRCChkCap- ECRCChkEn-
			MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
		HeaderLog: 00000000 00000000 00000000 00000000
	Capabilities: [140 v1] Device Serial Number a0-c5-89-ff-ff-a7-cc-13
	Capabilities: [14c v1] Latency Tolerance Reporting
		Max snoop latency: 3145728ns
		Max no snoop latency: 3145728ns
	Capabilities: [154 v1] L1 PM Substates
		L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
			  PortCommonModeRestoreTime=30us PortTPowerOnTime=60us
		L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
			   T_CommonMode=0us LTR1.2_Threshold=0ns
		L1SubCtl2: T_PwrOn=10us
00: 86 80 65 31 00 00 10 00 81 00 80 02 00 00 00 00
10: 04 00 30 91 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 10 40
30: 00 00 00 00 c8 00 00 00 00 00 00 00 0a 01 00 00
40: 10 00 02 00 c0 8e 00 10 10 0c 10 00 11 e8 46 00
50: 40 01 11 10 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 12 08 08 00 05 04 00 00 00 00 00 00
70: 01 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 01 d0 23 c8 00 00 00 0d
d0: 05 40 80 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 0c)
	Subsystem: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 20
	Region 0: I/O ports at e000 [size=256]
	Region 2: Memory at 91204000 (64-bit, non-prefetchable) [size=4K]
	Region 4: Memory at 91200000 (64-bit, prefetchable) [size=16K]
	Capabilities: [40] Power Management version 3
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D3 NoSoftRst+ PME-Enable+ DSel=0 DScale=0 PME-
	Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
		Address: 0000000000000000  Data: 0000
	Capabilities: [70] Express (v2) Endpoint, MSI 01
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 10.000W
		DevCtl:	CorrErr- NonFatalErr- FatalErr- UnsupReq-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us
			ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk+
			ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s (ok), Width x1 (ok)
			TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, NROPrPrP-, LTR+
			 10BitTagComp-, 10BitTagReq-, OBFF Via message/WAKE#, ExtFmt-, EETLPPrefix-
			 EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
			 FRS-, TPHComp-, ExtTPHComp-
			 AtomicOpsCap: 32bit- 64bit- 128bitCAS-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled
			 AtomicOpsCtl: ReqEn-
		LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [b0] MSI-X: Enable+ Count=4 Masked-
		Vector table: BAR=4 offset=00000000
		PBA: BAR=4 offset=00000800
	Capabilities: [d0] Vital Product Data
		Not readable
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
		AERCap:	First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
			MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
		HeaderLog: 00000000 00000000 00000000 00000000
	Capabilities: [140 v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
			Status:	NegoPending- InProgress-
	Capabilities: [160 v1] Device Serial Number 01-00-00-00-68-4c-e0-00
	Capabilities: [170 v1] Latency Tolerance Reporting
		Max snoop latency: 3145728ns
		Max no snoop latency: 3145728ns
	Kernel driver in use: r8169
	Kernel modules: r8169
00: ec 10 68 81 07 04 10 00 0c 00 00 02 10 00 00 00
10: 01 e0 00 00 00 00 00 00 04 40 20 91 00 00 00 00
20: 0c 00 20 91 00 00 00 00 00 00 00 00 ec 10 23 01
30: 00 00 00 00 40 00 00 00 00 00 00 00 07 01 00 00
40: 01 50 c3 ff 0b 01 00 00 00 00 00 00 00 00 00 00
50: 05 70 80 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 10 b0 02 02 c0 8c 90 05 10 20 10 00 11 7c 47 00
80: 40 01 11 10 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 1f 08 0c 00 00 04 00 00 02 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 11 d0 03 80 04 00 00 00 04 08 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 03 00 00 80 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 0c)
	Subsystem: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 23
	Region 0: I/O ports at d000 [size=256]
	Region 2: Memory at 91104000 (64-bit, non-prefetchable) [size=4K]
	Region 4: Memory at 91100000 (64-bit, prefetchable) [size=16K]
	Capabilities: [40] Power Management version 3
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
		Address: 0000000000000000  Data: 0000
	Capabilities: [70] Express (v2) Endpoint, MSI 01
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 10.000W
		DevCtl:	CorrErr- NonFatalErr- FatalErr- UnsupReq-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 4096 bytes
		DevSta:	CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us
			ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk+
			ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s (ok), Width x1 (ok)
			TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, NROPrPrP-, LTR+
			 10BitTagComp-, 10BitTagReq-, OBFF Via message/WAKE#, ExtFmt-, EETLPPrefix-
			 EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
			 FRS-, TPHComp-, ExtTPHComp-
			 AtomicOpsCap: 32bit- 64bit- 128bitCAS-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled
			 AtomicOpsCtl: ReqEn-
		LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [b0] MSI-X: Enable+ Count=4 Masked-
		Vector table: BAR=4 offset=00000000
		PBA: BAR=4 offset=00000800
	Capabilities: [d0] Vital Product Data
		Not readable
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
		AERCap:	First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
			MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
		HeaderLog: 00000000 00000000 00000000 00000000
	Capabilities: [140 v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
			Status:	NegoPending- InProgress-
	Capabilities: [160 v1] Device Serial Number 01-00-00-00-68-4c-e0-00
	Capabilities: [170 v1] Latency Tolerance Reporting
		Max snoop latency: 3145728ns
		Max no snoop latency: 3145728ns
	Kernel driver in use: r8169
	Kernel modules: r8169
00: ec 10 68 81 07 04 10 00 0c 00 00 02 10 00 00 00
10: 01 d0 00 00 00 00 00 00 04 40 10 91 00 00 00 00
20: 0c 00 10 91 00 00 00 00 00 00 00 00 ec 10 23 01
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 00 00
40: 01 50 c3 ff 08 00 00 00 00 00 00 00 00 00 00 00
50: 05 70 80 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 10 b0 02 02 c0 8c 90 05 10 50 10 00 11 7c 47 00
80: 40 01 11 10 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 1f 08 0c 00 00 04 00 00 02 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 11 d0 03 80 04 00 00 00 04 08 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 03 00 00 80 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00


[-- Attachment #4: lspci_vvxxx_wo_aspm --]
[-- Type: text/plain, Size: 46288 bytes --]

00:00.0 Host bridge: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series Host Bridge (rev 0b)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
00: 86 80 f0 5a 07 00 00 00 0b 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00
40: 00 00 00 00 00 00 00 00 01 00 d1 fe 00 00 00 00
50: c1 02 00 00 11 00 00 00 07 00 f0 7f 00 00 00 00
60: 01 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 80 01 00 00 00
b0: 01 00 00 7c 01 00 80 7b 01 00 00 7b 01 00 00 80
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 10 38 00 00
e0: 09 00 0c 01 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 0f 1c 01 00 00 00 00 00 00 00 00

00:02.0 VGA compatible controller: Intel Corporation HD Graphics 500 (rev 0b) (prog-if 00 [VGA controller])
	DeviceName:  Onboard IGD
	Subsystem: ZOTAC International (MCO) Ltd. HD Graphics 500
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 127
	Region 0: Memory at 90000000 (64-bit, non-prefetchable) [size=16M]
	Region 2: Memory at 80000000 (64-bit, prefetchable) [size=256M]
	Region 4: I/O ports at f000 [size=64]
	Expansion ROM at 000c0000 [virtual] [disabled] [size=128K]
	Capabilities: [40] Vendor Specific Information: Len=0c <?>
	Capabilities: [70] Express (v2) Root Complex Integrated Endpoint, MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0
			ExtTag- RBE+ FLReset+
		DevCtl:	CorrErr- NonFatalErr- FatalErr- UnsupReq-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- FLReset-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
		DevCap2: Completion Timeout: Not Supported, TimeoutDis-, NROPrPrP-, LTR-
			 10BitTagComp-, 10BitTagReq-, OBFF Not Supported, ExtFmt-, EETLPPrefix-
			 EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
			 FRS-
			 AtomicOpsCap: 32bit- 64bit- 128bitCAS-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
			 AtomicOpsCtl: ReqEn-
	Capabilities: [ac] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee08004  Data: 4023
	Capabilities: [d0] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [100 v1] Process Address Space ID (PASID)
		PASIDCap: Exec+ Priv-, Max PASID Width: 14
		PASIDCtl: Enable- Exec- Priv-
	Capabilities: [200 v1] Address Translation Service (ATS)
		ATSCap:	Invalidate Queue Depth: 00
		ATSCtl:	Enable-, Smallest Translation Unit: 00
	Capabilities: [300 v1] Page Request Interface (PRI)
		PRICtl: Enable- Reset-
		PRISta: RF- UPRGI- Stopped-
		Page Request Capacity: 00008000, Page Request Allocation: 00000000
	Kernel driver in use: i915
	Kernel modules: i915
00: 86 80 85 5a 07 04 10 00 0b 00 00 03 00 00 00 00
10: 04 00 00 90 00 00 00 00 0c 00 00 80 00 00 00 00
20: 01 f0 00 00 00 00 00 00 00 00 00 00 da 19 25 b3
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 00 00
40: 09 70 0c 01 00 00 00 00 00 00 00 00 00 00 00 00
50: c1 02 00 00 11 00 00 00 00 00 00 00 01 00 00 7c
60: 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 10 ac 92 00 00 80 00 10 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 05 d0 01 00
b0: 04 80 e0 fe 23 40 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 01 00 22 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 18 40 b7 79

00:0e.0 Audio device: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series Audio Cluster (rev 0b)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 129
	Region 0: Memory at 91410000 (64-bit, non-prefetchable) [size=16K]
	Region 4: Memory at 91000000 (64-bit, non-prefetchable) [size=1M]
	Capabilities: [50] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D3 NoSoftRst+ PME-Enable+ DSel=0 DScale=0 PME-
	Capabilities: [80] Vendor Specific Information: Len=14 <?>
	Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
		Address: 00000000fee01004  Data: 4023
	Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0
			ExtTag- RBE- FLReset+
		DevCtl:	CorrErr- NonFatalErr- FatalErr- UnsupReq-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- FLReset-
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
	Kernel driver in use: snd_hda_intel
	Kernel modules: snd_hda_intel
00: 86 80 98 5a 06 04 10 00 0b 00 03 04 00 00 00 00
10: 04 00 41 91 00 00 00 00 00 00 00 00 00 00 00 00
20: 04 00 00 91 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 19 01 00 00
40: 00 00 00 00 00 00 00 00 ff 0d 7b 80 00 00 00 00
50: 01 80 43 c8 0b 01 00 00 00 00 00 00 00 00 00 00
60: 05 70 81 00 04 10 e0 fe 00 00 00 00 23 40 00 00
70: 10 00 91 00 00 00 00 10 00 20 10 00 00 00 00 00
80: 09 60 14 f0 10 00 40 01 00 00 00 00 a1 04 01 00
90: 00 08 28 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 08 06 02 00 00 70 00 04 00 0c a5 82 10 00 03 00
d0: 00 00 30 00 10 00 03 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 1c 0f 00 01 00 00 00 00

00:0f.0 Communication controller: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series Trusted Execution Engine (rev 0b)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 125
	Region 0: Memory at 91421000 (64-bit, non-prefetchable) [size=4K]
	Capabilities: [50] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+
		Address: 00000000fee04004  Data: 4023
	Capabilities: [a4] Vendor Specific Information: Len=14 <?>
	Kernel driver in use: mei_me
	Kernel modules: mei_me
00: 86 80 9a 5a 06 04 10 00 0b 00 80 07 00 00 80 00
10: 04 10 42 91 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 07 01 00 00
40: 55 02 00 80 00 00 01 80 00 04 f4 09 00 00 00 00
50: 01 8c 03 40 08 00 00 00 00 00 00 00 00 00 00 00
60: 08 06 b5 30 00 00 08 00 00 00 00 00 00 00 00 00
70: 08 00 b5 c0 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 05 a4 81 00
90: 04 40 e0 fe 00 00 00 00 23 40 00 00 00 00 00 00
a0: 00 00 00 00 09 00 14 f0 10 00 40 01 00 00 00 00
b0: 01 80 00 00 38 0d 0e 00 00 00 00 00 00 00 00 40
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 1c 0f 00 01 00 00 00 00

00:12.0 SATA controller: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series SATA AHCI Controller (rev 0b) (prog-if 01 [AHCI 1.0])
	Subsystem: ZOTAC International (MCO) Ltd. Celeron N3350/Pentium N4200/Atom E3900 Series SATA AHCI Controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 124
	Region 0: Memory at 91414000 (32-bit, non-prefetchable) [size=8K]
	Region 1: Memory at 9141e000 (32-bit, non-prefetchable) [size=256]
	Region 2: I/O ports at f090 [size=8]
	Region 3: I/O ports at f080 [size=4]
	Region 4: I/O ports at f060 [size=32]
	Region 5: Memory at 9141d000 (32-bit, non-prefetchable) [size=2K]
	Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee08004  Data: 4022
	Capabilities: [70] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
		Status: D0 NoSoftRst+ PME-Enable+ DSel=0 DScale=0 PME-
	Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
	Kernel driver in use: ahci
	Kernel modules: ahci
00: 86 80 e3 5a 07 04 b0 02 0b 01 06 01 00 00 00 00
10: 00 40 41 91 00 e0 41 91 91 f0 00 00 81 f0 00 00
20: 61 f0 00 00 00 d0 41 91 00 00 00 00 da 19 25 b3
30: 00 00 00 00 80 00 00 00 00 00 00 00 03 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 01 a8 03 40 08 01 00 00 00 00 00 00 00 00 00 00
80: 05 70 01 00 04 80 e0 fe 22 40 00 00 00 00 00 00
90: 00 00 06 00 01 00 01 00 00 00 00 00 30 70 00 80
a0: 90 00 00 00 03 00 00 00 12 00 10 00 48 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 11 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 1c 0f 00 01 00 00 00 00

00:13.0 PCI bridge: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series PCI Express Port A #1 (rev fb) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 120
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: [disabled]
	Memory behind bridge: 91300000-913fffff [size=1M]
	Prefetchable memory behind bridge: [disabled]
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 256 bytes, PhantFunc 0
			ExtTag- RBE+
		DevCtl:	CorrErr- NonFatalErr- FatalErr- UnsupReq-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
		LnkCap:	Port #3, Speed 5GT/s, Width x1, ASPM not supported
			ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s (downgraded), Width x1 (ok)
			TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
			Slot #2, PowerLimit 10.000W; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
			Changed: MRL- PresDet- LinkState+
		RootCap: CRSVisible-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
		DevCap2: Completion Timeout: Range ABC, TimeoutDis+, NROPrPrP-, LTR+
			 10BitTagComp-, 10BitTagReq-, OBFF Not Supported, ExtFmt-, EETLPPrefix-
			 EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
			 FRS-, LN System CLS Not Supported, TPHComp-, ExtTPHComp-, ARIFwd+
			 AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled ARIFwd-
			 AtomicOpsCtl: ReqEn- EgressBlck-
		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee04004  Data: 4021
	Capabilities: [90] Subsystem: ZOTAC International (MCO) Ltd. Celeron N3350/Pentium N4200/Atom E3900 Series PCI Express Port A
	Capabilities: [a0] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [100 v0] Null
	Capabilities: [140 v1] Access Control Services
		ACSCap:	SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd- EgressCtrl- DirectTrans-
		ACSCtl:	SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
	Capabilities: [150 v0] Null
	Capabilities: [200 v0] Null
	Kernel driver in use: pcieport
00: 86 80 d8 5a 07 04 10 00 fb 00 04 06 00 00 81 00
10: 00 00 00 00 00 00 00 00 00 01 01 00 f0 00 00 20
20: 30 91 30 91 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 12 00
40: 10 80 42 01 01 80 00 00 00 00 10 00 12 40 71 03
50: 40 00 11 70 00 b2 14 00 00 00 40 01 00 00 00 00
60: 00 00 00 00 37 08 00 00 00 04 00 00 06 00 00 00
70: 42 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 90 01 00 04 40 e0 fe 21 40 00 00 00 00 00 00
90: 0d a0 00 00 da 19 25 b3 00 00 00 00 00 00 00 00
a0: 01 00 03 c8 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 77 90 00 00 42 1a 00 00 00 00 92 03 00 00 00 00
e0: 00 77 f3 00 00 00 00 00 16 80 03 00 00 00 00 00
f0: 50 07 00 00 00 07 00 40 1c 0f 00 01 04 00 00 01

00:13.2 PCI bridge: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series PCI Express Port A #3 (rev fb) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin C routed to IRQ 121
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	I/O behind bridge: 0000e000-0000efff [size=4K]
	Memory behind bridge: 91200000-912fffff [size=1M]
	Prefetchable memory behind bridge: [disabled]
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 256 bytes, PhantFunc 0
			ExtTag- RBE+
		DevCtl:	CorrErr- NonFatalErr- FatalErr- UnsupReq-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
		LnkCap:	Port #5, Speed 5GT/s, Width x1, ASPM not supported
			ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s (downgraded), Width x1 (ok)
			TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
			Slot #4, PowerLimit 10.000W; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
			Changed: MRL- PresDet- LinkState+
		RootCap: CRSVisible-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
		DevCap2: Completion Timeout: Range ABC, TimeoutDis+, NROPrPrP-, LTR+
			 10BitTagComp-, 10BitTagReq-, OBFF Not Supported, ExtFmt-, EETLPPrefix-
			 EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
			 FRS-, LN System CLS Not Supported, TPHComp-, ExtTPHComp-, ARIFwd+
			 AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled ARIFwd-
			 AtomicOpsCtl: ReqEn- EgressBlck-
		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee08004  Data: 4021
	Capabilities: [90] Subsystem: ZOTAC International (MCO) Ltd. Celeron N3350/Pentium N4200/Atom E3900 Series PCI Express Port A
	Capabilities: [a0] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [100 v0] Null
	Capabilities: [140 v1] Access Control Services
		ACSCap:	SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd- EgressCtrl- DirectTrans-
		ACSCtl:	SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
	Capabilities: [150 v0] Null
	Capabilities: [200 v0] Null
	Kernel driver in use: pcieport
00: 86 80 da 5a 07 04 10 00 fb 00 04 06 00 00 81 00
10: 00 00 00 00 00 00 00 00 00 02 02 00 e0 e0 00 20
20: 20 91 20 91 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 07 03 12 00
40: 10 80 42 01 01 80 00 00 00 00 10 00 12 40 71 05
50: 40 00 11 70 00 b2 24 00 00 00 40 01 00 00 00 00
60: 00 00 00 00 37 08 00 00 00 04 00 00 06 00 00 00
70: 42 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 90 01 00 04 80 e0 fe 21 40 00 00 00 00 00 00
90: 0d a0 00 00 da 19 25 b3 00 00 00 00 00 00 00 00
a0: 01 00 03 c8 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 77 10 00 00 42 1a 00 00 00 00 92 03 00 00 00 00
e0: 00 03 e3 00 00 00 00 00 16 00 01 00 00 00 00 00
f0: 50 07 00 00 00 04 00 4c 1c 0f 00 01 04 00 00 03

00:14.0 PCI bridge: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series PCI Express Port B #2 (rev fb) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 122
	Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
	I/O behind bridge: 0000d000-0000dfff [size=4K]
	Memory behind bridge: 91100000-911fffff [size=1M]
	Prefetchable memory behind bridge: [disabled]
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 256 bytes, PhantFunc 0
			ExtTag- RBE+
		DevCtl:	CorrErr- NonFatalErr- FatalErr- UnsupReq-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
		LnkCap:	Port #2, Speed 5GT/s, Width x1, ASPM not supported
			ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s (downgraded), Width x1 (ok)
			TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
			Slot #1, PowerLimit 10.000W; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
			Changed: MRL- PresDet- LinkState+
		RootCap: CRSVisible-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
		DevCap2: Completion Timeout: Range ABC, TimeoutDis+, NROPrPrP-, LTR+
			 10BitTagComp-, 10BitTagReq-, OBFF Not Supported, ExtFmt-, EETLPPrefix-
			 EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
			 FRS-, LN System CLS Not Supported, TPHComp-, ExtTPHComp-, ARIFwd+
			 AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled ARIFwd-
			 AtomicOpsCtl: ReqEn- EgressBlck-
		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee01004  Data: 4021
	Capabilities: [90] Subsystem: ZOTAC International (MCO) Ltd. Celeron N3350/Pentium N4200/Atom E3900 Series PCI Express Port B
	Capabilities: [a0] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [100 v0] Null
	Capabilities: [140 v1] Access Control Services
		ACSCap:	SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd- EgressCtrl- DirectTrans-
		ACSCtl:	SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
	Capabilities: [150 v0] Null
	Capabilities: [200 v0] Null
	Kernel driver in use: pcieport
00: 86 80 d7 5a 07 04 10 00 fb 00 04 06 00 00 81 00
10: 00 00 00 00 00 00 00 00 00 03 03 00 d0 d0 00 20
20: 10 91 10 91 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 ff 02 12 00
40: 10 80 42 01 01 80 00 00 00 00 10 00 12 40 71 02
50: 40 00 11 70 00 b2 0c 00 00 00 40 01 00 00 00 00
60: 00 00 00 00 37 08 00 00 00 04 00 00 06 00 00 00
70: 42 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 90 01 00 04 10 e0 fe 21 40 00 00 00 00 00 00
90: 0d a0 00 00 da 19 25 b3 00 00 00 00 00 00 00 00
a0: 01 00 03 c8 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 77 10 00 00 42 1a 00 00 00 00 92 03 00 00 00 00
e0: 00 03 e3 00 00 00 3c 88 16 00 01 00 00 00 00 00
f0: 50 07 00 00 00 04 00 4c 1c 0f 00 01 04 00 00 02

00:15.0 USB controller: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series USB xHCI (rev 0b) (prog-if 30 [XHCI])
	Subsystem: ZOTAC International (MCO) Ltd. Celeron N3350/Pentium N4200/Atom E3900 Series USB xHCI
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 123
	Region 0: Memory at 91400000 (64-bit, non-prefetchable) [size=64K]
	Capabilities: [70] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+
		Address: 00000000fee02004  Data: 4022
	Capabilities: [90] Vendor Specific Information: Len=14 <?>
	Kernel driver in use: xhci_hcd
00: 86 80 a8 5a 06 04 90 02 0b 30 03 0c 00 00 80 00
10: 04 00 40 91 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 da 19 25 b3
30: 00 00 00 00 70 00 00 00 00 00 00 00 11 01 00 00
40: fd 01 34 80 8f c6 cf 83 00 00 00 00 00 00 00 00
50: 5f 6e ce 0f 00 00 00 00 00 00 00 00 00 00 00 00
60: 30 60 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 01 80 c2 c1 08 00 00 00 00 00 00 00 00 00 00 00
80: 05 90 87 00 04 20 e0 fe 00 00 00 00 22 40 00 00
90: 09 00 14 f0 10 00 40 01 00 00 00 00 c1 0a 08 00
a0: 00 08 0e 00 00 18 00 00 8f 40 02 00 00 01 04 00
b0: 01 00 00 00 3e 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 01 00 00 00 3e 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 1c 0f 00 01 02 00 00 00

00:1a.0 Serial bus controller [0c80]: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series PWM Pin Controller (rev 0b)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 255
	Region 0: Memory at 9141c000 (64-bit, non-prefetchable) [size=4K]
	Region 2: Memory at 9141b000 (64-bit, non-prefetchable) [size=4K]
	Capabilities: [80] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [90] Vendor Specific Information: Len=14 <?>
00: 86 80 c8 5a 06 00 10 00 0b 00 80 0c 00 00 00 00
10: 04 c0 41 91 00 00 00 00 04 b0 41 91 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 ff 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 01 90 03 48 08 00 00 00 00 00 00 00 00 00 00 00
90: 09 00 14 f0 10 00 40 01 00 00 00 00 01 10 00 00
a0: 00 00 06 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 1c 0f 00 01 00 00 00 00

00:1c.0 SD Host controller: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series eMMC Controller (rev 0b) (prog-if 01)
	Subsystem: ZOTAC International (MCO) Ltd. Celeron N3350/Pentium N4200/Atom E3900 Series eMMC Controller
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 39
	Region 0: Memory at 9141a000 (64-bit, non-prefetchable) [size=4K]
	Region 2: Memory at 91419000 (64-bit, non-prefetchable) [size=4K]
	Capabilities: [80] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [90] Vendor Specific Information: Len=14 <?>
00: 86 80 cc 5a 06 00 10 00 0b 01 05 08 00 00 00 00
10: 04 a0 41 91 00 00 00 00 04 90 41 91 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 da 19 25 b3
30: 00 00 00 00 80 00 00 00 00 00 00 00 27 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 01 90 03 00 08 00 00 00 00 00 00 00 00 00 00 00
90: 09 00 14 f0 10 00 40 01 41 80 00 00 c1 81 00 00
a0: 00 08 2f 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 1c 0f 00 01 00 00 00 00

00:1e.0 SD Host controller: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series SDIO Controller (rev 0b) (prog-if 01)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 42
	Region 0: Memory at 91418000 (64-bit, non-prefetchable) [size=4K]
	Region 2: Memory at 91417000 (64-bit, non-prefetchable) [size=4K]
	Capabilities: [80] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [90] Vendor Specific Information: Len=14 <?>
00: 86 80 d0 5a 06 00 10 00 0b 01 05 08 00 00 00 00
10: 04 80 41 91 00 00 00 00 04 70 41 91 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 2a 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 01 90 03 00 08 00 00 00 00 00 00 00 00 00 00 00
90: 09 00 14 f0 10 00 40 01 41 80 00 00 c1 81 00 00
a0: 00 08 2f 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 1c 0f 00 01 00 00 00 00

00:1f.0 ISA bridge: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series Low Pin Count Interface (rev 0b)
	Subsystem: ZOTAC International (MCO) Ltd. Celeron N3350/Pentium N4200/Atom E3900 Series Low Pin Count Interface
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
00: 86 80 e8 5a 07 00 00 02 0b 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 da 19 25 b3
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 d0 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 0f 3f 81 00 0c 00 01 0a 3c 00 00 00 00 00
90: 00 00 00 00 00 0f 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 33 22 11 00 67 45 00 00 cf ff 00 00 80 00 00 00
e0: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 1c 0f 00 01 00 00 00 00

00:1f.1 SMBus: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series SMBus Controller (rev 0b)
	Subsystem: ZOTAC International (MCO) Ltd. Celeron N3350/Pentium N4200/Atom E3900 Series SMBus Controller
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin A routed to IRQ -2147483648
	Region 0: Memory at 91416000 (64-bit, non-prefetchable) [size=256]
	Region 4: I/O ports at f040 [size=32]
	Kernel driver in use: i801_smbus
	Kernel modules: i2c_i801
00: 86 80 d4 5a 03 00 80 02 0b 00 05 0c 00 00 00 00
10: 04 60 41 91 00 00 00 00 00 00 00 00 00 00 00 00
20: 41 f0 00 00 00 00 00 00 00 00 00 00 da 19 25 b3
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 01 00 00
40: 11 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 05 00 00 00 01 00 00 00 00 00 00 00 00 00 00
60: 03 04 04 00 00 00 08 08 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 24 00 04 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 1c 0f 00 01 00 00 00 00

01:00.0 Network controller: Intel Corporation Wireless 3165 (rev 81)
	Subsystem: Intel Corporation Dual Band Wireless AC 3165
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at 91300000 (64-bit, non-prefetchable) [disabled] [size=8K]
	Capabilities: [c8] Power Management version 3
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
		Address: 0000000000000000  Data: 0000
	Capabilities: [40] Express (v2) Endpoint, MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 unlimited
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ SlotPowerLimit 0.000W
		DevCtl:	CorrErr- NonFatalErr- FatalErr- UnsupReq-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr+ NoSnoop+ FLReset-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L1, Exit Latency L1 <32us
			ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk+
			ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s (ok), Width x1 (ok)
			TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		DevCap2: Completion Timeout: Range B, TimeoutDis+, NROPrPrP-, LTR+
			 10BitTagComp-, 10BitTagReq-, OBFF Via WAKE#, ExtFmt-, EETLPPrefix-
			 EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
			 FRS-, TPHComp-, ExtTPHComp-
			 AtomicOpsCap: 32bit- 64bit- 128bitCAS-
		DevCtl2: Completion Timeout: 16ms to 55ms, TimeoutDis-, LTR+, OBFF Disabled
			 AtomicOpsCtl: ReqEn-
		LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
		AERCap:	First Error Pointer: 00, ECRCGenCap- ECRCGenEn- ECRCChkCap- ECRCChkEn-
			MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
		HeaderLog: 00000000 00000000 00000000 00000000
	Capabilities: [140 v1] Device Serial Number a0-c5-89-ff-ff-a7-cc-13
	Capabilities: [14c v1] Latency Tolerance Reporting
		Max snoop latency: 3145728ns
		Max no snoop latency: 3145728ns
	Capabilities: [154 v1] L1 PM Substates
		L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
			  PortCommonModeRestoreTime=30us PortTPowerOnTime=60us
		L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
			   T_CommonMode=0us LTR1.2_Threshold=0ns
		L1SubCtl2: T_PwrOn=10us
00: 86 80 65 31 00 00 10 00 81 00 80 02 00 00 00 00
10: 04 00 30 91 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 10 40
30: 00 00 00 00 c8 00 00 00 00 00 00 00 0a 01 00 00
40: 10 00 02 00 c0 8e 00 10 10 0c 10 00 11 e8 46 00
50: 40 01 11 10 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 12 08 08 00 05 04 00 00 00 00 00 00
70: 01 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 01 d0 23 c8 00 00 00 0d
d0: 05 40 80 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 0c)
	Subsystem: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 20
	Region 0: I/O ports at e000 [size=256]
	Region 2: Memory at 91204000 (64-bit, non-prefetchable) [size=4K]
	Region 4: Memory at 91200000 (64-bit, prefetchable) [size=16K]
	Capabilities: [40] Power Management version 3
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D3 NoSoftRst+ PME-Enable+ DSel=0 DScale=0 PME-
	Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
		Address: 0000000000000000  Data: 0000
	Capabilities: [70] Express (v2) Endpoint, MSI 01
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 10.000W
		DevCtl:	CorrErr- NonFatalErr- FatalErr- UnsupReq-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us
			ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk+
			ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s (ok), Width x1 (ok)
			TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, NROPrPrP-, LTR+
			 10BitTagComp-, 10BitTagReq-, OBFF Via message/WAKE#, ExtFmt-, EETLPPrefix-
			 EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
			 FRS-, TPHComp-, ExtTPHComp-
			 AtomicOpsCap: 32bit- 64bit- 128bitCAS-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled
			 AtomicOpsCtl: ReqEn-
		LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [b0] MSI-X: Enable+ Count=4 Masked-
		Vector table: BAR=4 offset=00000000
		PBA: BAR=4 offset=00000800
	Capabilities: [d0] Vital Product Data
		Not readable
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
		AERCap:	First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
			MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
		HeaderLog: 00000000 00000000 00000000 00000000
	Capabilities: [140 v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
			Status:	NegoPending- InProgress-
	Capabilities: [160 v1] Device Serial Number 01-00-00-00-68-4c-e0-00
	Capabilities: [170 v1] Latency Tolerance Reporting
		Max snoop latency: 3145728ns
		Max no snoop latency: 3145728ns
	Kernel driver in use: r8169
	Kernel modules: r8169
00: ec 10 68 81 07 04 10 00 0c 00 00 02 10 00 00 00
10: 01 e0 00 00 00 00 00 00 04 40 20 91 00 00 00 00
20: 0c 00 20 91 00 00 00 00 00 00 00 00 ec 10 23 01
30: 00 00 00 00 40 00 00 00 00 00 00 00 07 01 00 00
40: 01 50 c3 ff 0b 01 00 00 00 00 00 00 00 00 00 00
50: 05 70 80 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 10 b0 02 02 c0 8c 90 05 10 20 10 00 11 7c 47 00
80: 40 01 11 10 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 1f 08 0c 00 00 04 00 00 02 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 11 d0 03 80 04 00 00 00 04 08 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 03 00 00 80 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 0c)
	Subsystem: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 23
	Region 0: I/O ports at d000 [size=256]
	Region 2: Memory at 91104000 (64-bit, non-prefetchable) [size=4K]
	Region 4: Memory at 91100000 (64-bit, prefetchable) [size=16K]
	Capabilities: [40] Power Management version 3
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
		Address: 0000000000000000  Data: 0000
	Capabilities: [70] Express (v2) Endpoint, MSI 01
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 10.000W
		DevCtl:	CorrErr- NonFatalErr- FatalErr- UnsupReq-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 4096 bytes
		DevSta:	CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us
			ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk+
			ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s (ok), Width x1 (ok)
			TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, NROPrPrP-, LTR+
			 10BitTagComp-, 10BitTagReq-, OBFF Via message/WAKE#, ExtFmt-, EETLPPrefix-
			 EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
			 FRS-, TPHComp-, ExtTPHComp-
			 AtomicOpsCap: 32bit- 64bit- 128bitCAS-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled
			 AtomicOpsCtl: ReqEn-
		LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [b0] MSI-X: Enable+ Count=4 Masked-
		Vector table: BAR=4 offset=00000000
		PBA: BAR=4 offset=00000800
	Capabilities: [d0] Vital Product Data
		Not readable
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
		AERCap:	First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
			MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
		HeaderLog: 00000000 00000000 00000000 00000000
	Capabilities: [140 v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
			Status:	NegoPending- InProgress-
	Capabilities: [160 v1] Device Serial Number 01-00-00-00-68-4c-e0-00
	Capabilities: [170 v1] Latency Tolerance Reporting
		Max snoop latency: 3145728ns
		Max no snoop latency: 3145728ns
	Kernel driver in use: r8169
	Kernel modules: r8169
00: ec 10 68 81 07 04 10 00 0c 00 00 02 10 00 00 00
10: 01 d0 00 00 00 00 00 00 04 40 10 91 00 00 00 00
20: 0c 00 10 91 00 00 00 00 00 00 00 00 ec 10 23 01
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 00 00
40: 01 50 c3 ff 08 00 00 00 00 00 00 00 00 00 00 00
50: 05 70 80 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 10 b0 02 02 c0 8c 90 05 10 50 10 00 11 7c 47 00
80: 40 01 11 10 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 1f 08 0c 00 00 04 00 00 02 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 11 d0 03 80 04 00 00 00 04 08 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 03 00 00 80 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00


^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: Lost PCIe PME after a914ff2d78ce ("PCI/ASPM: Don't select CONFIG_PCIEASPM by default")
  2020-05-29 19:40     ` Heiner Kallweit
@ 2020-05-29 20:09       ` Heiner Kallweit
  2020-05-29 20:21         ` Bjorn Helgaas
  0 siblings, 1 reply; 15+ messages in thread
From: Heiner Kallweit @ 2020-05-29 20:09 UTC (permalink / raw)
  To: Bjorn Helgaas, Rafael J. Wysocki
  Cc: Bjorn Helgaas, linux-pci, linux-kernel, linux-acpi

On 29.05.2020 21:40, Heiner Kallweit wrote:
> On 29.05.2020 21:21, Bjorn Helgaas wrote:
>> [+cc Rafael, linux-kernel]
>>
>> On Fri, May 29, 2020 at 08:50:46PM +0200, Heiner Kallweit wrote:
>>> On 28.05.2020 23:44, Heiner Kallweit wrote:
>>>> For whatever reason with this change (and losing ASPM control) I also
>>>> loose the PCIe PME interrupts. This prevents my network card from
>>>> resuming from runtime-suspend.
>>>> Reverting the change brings back ASPM control and the PCIe PME irq's.
>>>>
>>>> Affected system is a Zotac MiniPC with a N3450 CPU:
>>>> PCI bridge: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series PCI Express Port A #1 (rev fb)
>>>>
>>> I checked a little bit further and w/o ASPM control the root ports
>>> don't have the PME service bit set in their capabilities.
>>> Not sure whether this is a chipset bug or whether there's a better
>>> explanation. However more chipsets may have such a behavior.
>>
>> Hmm.  Is the difference simply changing the PCIEASPM config symbol, or
>> are you booting with command-line arguments like "pcie_aspm=off"?
>>
> Only difference is the config symbol. My command line is plain and simple:
> 
> Command line: initrd=\intel-ucode.img initrd=\initramfs-linux.img root=/dev/sda2 rw
> 
>> What's the specific PME bit that changes in the root ports?  Can you
>> collect the "sudo lspci -vvxxxx" output with and without ASPM?
>>
>> The capability bits are generally read-only as far as the PCI spec is
>> concerned, but devices have implementation-specific knobs that the
>> BIOS may use to change things.  Without CONFIG_PCIEASPM, Linux will
>> not request control of LTR, and that could cause the BIOS to change
>> something.  You should be able to see the LTR control difference in
>> the dmesg logging about _OSC.
>>
>>> W/o the "default y" for ASPM control we also have the situation now
>>> that the config option description says "When in doubt, say Y."
>>> but it takes the EXPERT mode to enable it. This seems to be a little
>>> bit inconsistent.
>>
>> We should probably remove the "if EXPERT" from the PCIEASPM kconfig.
>> But I would expect PME to work correctly regardless of PCIEASPM, so
>> removing "if EXPERT" doesn't solve the underlying problem.
>>
>> Rafael, does this ring any bells for you?  I don't remember a
>> connection between PME and ASPM, but maybe there is one.
>>
>>> To cut a long story short:
>>> At least on some systems this change has unwanted side effects.
> 
> lspci output w/ and w/o ASPM is attached incl. a diff.
> Here comes the _OSC difference.
> 
> w/o ASPM
> 
> [    0.386063] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig Segments MSI HPX-Type3]
> [    0.386918] acpi PNP0A08:00: _OSC: not requesting OS control; OS requires [ExtendedConfig ASPM ClockPM MSI]
> 
> w/ ASPM
> [    0.388141] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3]
> [    0.393648] acpi PNP0A08:00: _OSC: OS now controls [PME AER PCIeCapability LTR]
> 
> It's at least interesting that w/o ASPM OS doesn't control PME and AER.
> 

This was the right entry point, also w/o ASPM control OS states to ACPI that it
needs ASPM and ClockPM. The following patch fixes the PME issue for me.
See also the _OSC part below.


diff --git a/drivers/acpi/pci_root.c b/drivers/acpi/pci_root.c
index 9e235c1a7..8df1fa728 100644
--- a/drivers/acpi/pci_root.c
+++ b/drivers/acpi/pci_root.c
@@ -38,10 +38,15 @@ static int acpi_pci_root_scan_dependent(struct acpi_device *adev)
 	return 0;
 }
 
+#ifdef CONFIG_PCIEASPM
 #define ACPI_PCIE_REQ_SUPPORT (OSC_PCI_EXT_CONFIG_SUPPORT \
 				| OSC_PCI_ASPM_SUPPORT \
 				| OSC_PCI_CLOCK_PM_SUPPORT \
 				| OSC_PCI_MSI_SUPPORT)
+#else
+#define ACPI_PCIE_REQ_SUPPORT (OSC_PCI_EXT_CONFIG_SUPPORT \
+				| OSC_PCI_MSI_SUPPORT)
+#endif
 
 static const struct acpi_device_id root_device_ids[] = {
 	{"PNP0A03", 0},
-- 
2.26.2


[    0.387527] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig Segments MSI HPX-Type3]
[    0.393033] acpi PNP0A08:00: _OSC: OS now controls [PME AER PCIeCapability]

^ permalink raw reply related	[flat|nested] 15+ messages in thread

* Re: Lost PCIe PME after a914ff2d78ce ("PCI/ASPM: Don't select CONFIG_PCIEASPM by default")
  2020-05-29 20:09       ` Heiner Kallweit
@ 2020-05-29 20:21         ` Bjorn Helgaas
  2020-05-29 20:53           ` Heiner Kallweit
  2020-05-29 20:59           ` Matthew Garrett
  0 siblings, 2 replies; 15+ messages in thread
From: Bjorn Helgaas @ 2020-05-29 20:21 UTC (permalink / raw)
  To: Heiner Kallweit
  Cc: Rafael J. Wysocki, Bjorn Helgaas, linux-pci, linux-kernel,
	linux-acpi, Matthew Garrett

[+cc Matthew]

On Fri, May 29, 2020 at 10:09:08PM +0200, Heiner Kallweit wrote:
> On 29.05.2020 21:40, Heiner Kallweit wrote:
> > On 29.05.2020 21:21, Bjorn Helgaas wrote:
> >> On Fri, May 29, 2020 at 08:50:46PM +0200, Heiner Kallweit wrote:
> >>> On 28.05.2020 23:44, Heiner Kallweit wrote:
> >>>> For whatever reason with this change (and losing ASPM control) I also
> >>>> loose the PCIe PME interrupts. This prevents my network card from
> >>>> resuming from runtime-suspend.
> >>>> Reverting the change brings back ASPM control and the PCIe PME irq's.
> >>>>
> >>>> Affected system is a Zotac MiniPC with a N3450 CPU:
> >>>> PCI bridge: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series PCI Express Port A #1 (rev fb)
> >>>>
> >>> I checked a little bit further and w/o ASPM control the root ports
> >>> don't have the PME service bit set in their capabilities.
> >>> Not sure whether this is a chipset bug or whether there's a better
> >>> explanation. However more chipsets may have such a behavior.
> >>
> >> Hmm.  Is the difference simply changing the PCIEASPM config symbol, or
> >> are you booting with command-line arguments like "pcie_aspm=off"?
> >>
> > Only difference is the config symbol. My command line is plain and simple:
> > 
> > Command line: initrd=\intel-ucode.img initrd=\initramfs-linux.img root=/dev/sda2 rw
> > 
> >> What's the specific PME bit that changes in the root ports?  Can you
> >> collect the "sudo lspci -vvxxxx" output with and without ASPM?
> >>
> >> The capability bits are generally read-only as far as the PCI spec is
> >> concerned, but devices have implementation-specific knobs that the
> >> BIOS may use to change things.  Without CONFIG_PCIEASPM, Linux will
> >> not request control of LTR, and that could cause the BIOS to change
> >> something.  You should be able to see the LTR control difference in
> >> the dmesg logging about _OSC.
> >>
> >>> W/o the "default y" for ASPM control we also have the situation now
> >>> that the config option description says "When in doubt, say Y."
> >>> but it takes the EXPERT mode to enable it. This seems to be a little
> >>> bit inconsistent.
> >>
> >> We should probably remove the "if EXPERT" from the PCIEASPM kconfig.
> >> But I would expect PME to work correctly regardless of PCIEASPM, so
> >> removing "if EXPERT" doesn't solve the underlying problem.
> >>
> >> Rafael, does this ring any bells for you?  I don't remember a
> >> connection between PME and ASPM, but maybe there is one.
> >>
> >>> To cut a long story short:
> >>> At least on some systems this change has unwanted side effects.
> > 
> > lspci output w/ and w/o ASPM is attached incl. a diff.
> > Here comes the _OSC difference.
> > 
> > w/o ASPM
> > 
> > [    0.386063] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig Segments MSI HPX-Type3]
> > [    0.386918] acpi PNP0A08:00: _OSC: not requesting OS control; OS requires [ExtendedConfig ASPM ClockPM MSI]
> > 
> > w/ ASPM
> > [    0.388141] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3]
> > [    0.393648] acpi PNP0A08:00: _OSC: OS now controls [PME AER PCIeCapability LTR]
> > 
> > It's at least interesting that w/o ASPM OS doesn't control PME and AER.
> > 
> 
> This was the right entry point, also w/o ASPM control OS states to ACPI that it
> needs ASPM and ClockPM. The following patch fixes the PME issue for me.
> See also the _OSC part below.
> 
> 
> diff --git a/drivers/acpi/pci_root.c b/drivers/acpi/pci_root.c
> index 9e235c1a7..8df1fa728 100644
> --- a/drivers/acpi/pci_root.c
> +++ b/drivers/acpi/pci_root.c
> @@ -38,10 +38,15 @@ static int acpi_pci_root_scan_dependent(struct acpi_device *adev)
>  	return 0;
>  }
>  
> +#ifdef CONFIG_PCIEASPM
>  #define ACPI_PCIE_REQ_SUPPORT (OSC_PCI_EXT_CONFIG_SUPPORT \
>  				| OSC_PCI_ASPM_SUPPORT \
>  				| OSC_PCI_CLOCK_PM_SUPPORT \
>  				| OSC_PCI_MSI_SUPPORT)
> +#else
> +#define ACPI_PCIE_REQ_SUPPORT (OSC_PCI_EXT_CONFIG_SUPPORT \
> +				| OSC_PCI_MSI_SUPPORT)
> +#endif

Yeah, that makes sense.  I can't remember the details, but I'm pretty
sure there's a reason why we ask for the whole set of things.  Seems
like it solved some problem.  I think Matthew Garrett might have been
involved in that.

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: Lost PCIe PME after a914ff2d78ce ("PCI/ASPM: Don't select CONFIG_PCIEASPM by default")
  2020-05-29 20:21         ` Bjorn Helgaas
@ 2020-05-29 20:53           ` Heiner Kallweit
  2020-05-29 20:59           ` Matthew Garrett
  1 sibling, 0 replies; 15+ messages in thread
From: Heiner Kallweit @ 2020-05-29 20:53 UTC (permalink / raw)
  To: Bjorn Helgaas
  Cc: Rafael J. Wysocki, Bjorn Helgaas, linux-pci, linux-kernel,
	linux-acpi, Matthew Garrett

On 29.05.2020 22:21, Bjorn Helgaas wrote:
> [+cc Matthew]
> 
> On Fri, May 29, 2020 at 10:09:08PM +0200, Heiner Kallweit wrote:
>> On 29.05.2020 21:40, Heiner Kallweit wrote:
>>> On 29.05.2020 21:21, Bjorn Helgaas wrote:
>>>> On Fri, May 29, 2020 at 08:50:46PM +0200, Heiner Kallweit wrote:
>>>>> On 28.05.2020 23:44, Heiner Kallweit wrote:
>>>>>> For whatever reason with this change (and losing ASPM control) I also
>>>>>> loose the PCIe PME interrupts. This prevents my network card from
>>>>>> resuming from runtime-suspend.
>>>>>> Reverting the change brings back ASPM control and the PCIe PME irq's.
>>>>>>
>>>>>> Affected system is a Zotac MiniPC with a N3450 CPU:
>>>>>> PCI bridge: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series PCI Express Port A #1 (rev fb)
>>>>>>
>>>>> I checked a little bit further and w/o ASPM control the root ports
>>>>> don't have the PME service bit set in their capabilities.
>>>>> Not sure whether this is a chipset bug or whether there's a better
>>>>> explanation. However more chipsets may have such a behavior.
>>>>
>>>> Hmm.  Is the difference simply changing the PCIEASPM config symbol, or
>>>> are you booting with command-line arguments like "pcie_aspm=off"?
>>>>
>>> Only difference is the config symbol. My command line is plain and simple:
>>>
>>> Command line: initrd=\intel-ucode.img initrd=\initramfs-linux.img root=/dev/sda2 rw
>>>
>>>> What's the specific PME bit that changes in the root ports?  Can you
>>>> collect the "sudo lspci -vvxxxx" output with and without ASPM?
>>>>
>>>> The capability bits are generally read-only as far as the PCI spec is
>>>> concerned, but devices have implementation-specific knobs that the
>>>> BIOS may use to change things.  Without CONFIG_PCIEASPM, Linux will
>>>> not request control of LTR, and that could cause the BIOS to change
>>>> something.  You should be able to see the LTR control difference in
>>>> the dmesg logging about _OSC.
>>>>
>>>>> W/o the "default y" for ASPM control we also have the situation now
>>>>> that the config option description says "When in doubt, say Y."
>>>>> but it takes the EXPERT mode to enable it. This seems to be a little
>>>>> bit inconsistent.
>>>>
>>>> We should probably remove the "if EXPERT" from the PCIEASPM kconfig.
>>>> But I would expect PME to work correctly regardless of PCIEASPM, so
>>>> removing "if EXPERT" doesn't solve the underlying problem.
>>>>
>>>> Rafael, does this ring any bells for you?  I don't remember a
>>>> connection between PME and ASPM, but maybe there is one.
>>>>
>>>>> To cut a long story short:
>>>>> At least on some systems this change has unwanted side effects.
>>>
>>> lspci output w/ and w/o ASPM is attached incl. a diff.
>>> Here comes the _OSC difference.
>>>
>>> w/o ASPM
>>>
>>> [    0.386063] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig Segments MSI HPX-Type3]
>>> [    0.386918] acpi PNP0A08:00: _OSC: not requesting OS control; OS requires [ExtendedConfig ASPM ClockPM MSI]
>>>
>>> w/ ASPM
>>> [    0.388141] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3]
>>> [    0.393648] acpi PNP0A08:00: _OSC: OS now controls [PME AER PCIeCapability LTR]
>>>
>>> It's at least interesting that w/o ASPM OS doesn't control PME and AER.
>>>
>>
>> This was the right entry point, also w/o ASPM control OS states to ACPI that it
>> needs ASPM and ClockPM. The following patch fixes the PME issue for me.
>> See also the _OSC part below.
>>
>>
>> diff --git a/drivers/acpi/pci_root.c b/drivers/acpi/pci_root.c
>> index 9e235c1a7..8df1fa728 100644
>> --- a/drivers/acpi/pci_root.c
>> +++ b/drivers/acpi/pci_root.c
>> @@ -38,10 +38,15 @@ static int acpi_pci_root_scan_dependent(struct acpi_device *adev)
>>  	return 0;
>>  }
>>  
>> +#ifdef CONFIG_PCIEASPM
>>  #define ACPI_PCIE_REQ_SUPPORT (OSC_PCI_EXT_CONFIG_SUPPORT \
>>  				| OSC_PCI_ASPM_SUPPORT \
>>  				| OSC_PCI_CLOCK_PM_SUPPORT \
>>  				| OSC_PCI_MSI_SUPPORT)
>> +#else
>> +#define ACPI_PCIE_REQ_SUPPORT (OSC_PCI_EXT_CONFIG_SUPPORT \
>> +				| OSC_PCI_MSI_SUPPORT)
>> +#endif
> 
> Yeah, that makes sense.  I can't remember the details, but I'm pretty
> sure there's a reason why we ask for the whole set of things.  Seems
> like it solved some problem.  I think Matthew Garrett might have been
> involved in that.
> 

ACPI_PCIE_REQ_SUPPORT was introduced with 415e12b23792 ("PCI/ACPI:
Request _OSC control once for each root bridge (v3)") in 2011.
It's linked to the following bug report:
https://bugzilla.kernel.org/show_bug.cgi?id=20232

I can't say whether there's a chance that the proposed patch would
bring back the issue discussed at that time.

If somebody thinks that the proposed patch isn't the right solution,
then presumably the following needs to be touched.

	if ((support & ACPI_PCIE_REQ_SUPPORT) != ACPI_PCIE_REQ_SUPPORT) {
		decode_osc_support(root, "not requesting OS control; OS requires",
				   ACPI_PCIE_REQ_SUPPORT);
		return;
	}

	control = OSC_PCI_EXPRESS_CAPABILITY_CONTROL
		| OSC_PCI_EXPRESS_PME_CONTROL;


^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: Lost PCIe PME after a914ff2d78ce ("PCI/ASPM: Don't select CONFIG_PCIEASPM by default")
  2020-05-29 20:21         ` Bjorn Helgaas
  2020-05-29 20:53           ` Heiner Kallweit
@ 2020-05-29 20:59           ` Matthew Garrett
  2020-05-29 22:26             ` Heiner Kallweit
  1 sibling, 1 reply; 15+ messages in thread
From: Matthew Garrett @ 2020-05-29 20:59 UTC (permalink / raw)
  To: Bjorn Helgaas
  Cc: Heiner Kallweit, Rafael J. Wysocki, Bjorn Helgaas, linux-pci,
	linux-kernel, linux-acpi

On Fri, May 29, 2020 at 03:21:35PM -0500, Bjorn Helgaas wrote:

> Yeah, that makes sense.  I can't remember the details, but I'm pretty
> sure there's a reason why we ask for the whole set of things.  Seems
> like it solved some problem.  I think Matthew Garrett might have been
> involved in that.

This was https://bugzilla.redhat.com/show_bug.cgi?id=638912 - some 
firmware misbehaves unless you pass the same set of supported 
functionality as Windows does.

-- 
Matthew Garrett | mjg59@srcf.ucam.org

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: Lost PCIe PME after a914ff2d78ce ("PCI/ASPM: Don't select CONFIG_PCIEASPM by default")
  2020-05-29 20:59           ` Matthew Garrett
@ 2020-05-29 22:26             ` Heiner Kallweit
  2020-05-29 22:58               ` Matthew Garrett
  0 siblings, 1 reply; 15+ messages in thread
From: Heiner Kallweit @ 2020-05-29 22:26 UTC (permalink / raw)
  To: Matthew Garrett, Bjorn Helgaas
  Cc: Rafael J. Wysocki, Bjorn Helgaas, linux-pci, linux-kernel, linux-acpi

On 29.05.2020 22:59, Matthew Garrett wrote:
> On Fri, May 29, 2020 at 03:21:35PM -0500, Bjorn Helgaas wrote:
> 
>> Yeah, that makes sense.  I can't remember the details, but I'm pretty
>> sure there's a reason why we ask for the whole set of things.  Seems
>> like it solved some problem.  I think Matthew Garrett might have been
>> involved in that.
> 
> This was https://bugzilla.redhat.com/show_bug.cgi?id=638912 - some 
> firmware misbehaves unless you pass the same set of supported 
> functionality as Windows does.
> 

Current situation means that PME is unusable on all systems where
pcie_aspm_support_enabled() returns false, what is basically every
system except EXPERT mode is enabled and CONFIG_PCIEASPM is set.
So we definitely need to do something.

One question is whether the system from the 10yr old bug report
actually depends on OSC_PCI_EXPRESS_LTR_CONTROL control, or whether
some other change in recent years fixed the issue.
Not sure whether the system is still available for re-testing.

If worst case we have 10yr old systems breaking with a new kernel
then we still would have the workaround to enable CONFIG_PCIEASPM
on that system.

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: Lost PCIe PME after a914ff2d78ce ("PCI/ASPM: Don't select CONFIG_PCIEASPM by default")
  2020-05-29 22:26             ` Heiner Kallweit
@ 2020-05-29 22:58               ` Matthew Garrett
  2020-05-30  6:33                 ` Heiner Kallweit
  0 siblings, 1 reply; 15+ messages in thread
From: Matthew Garrett @ 2020-05-29 22:58 UTC (permalink / raw)
  To: Heiner Kallweit
  Cc: Bjorn Helgaas, Rafael J. Wysocki, Bjorn Helgaas, linux-pci,
	linux-kernel, linux-acpi

On Sat, May 30, 2020 at 12:26:17AM +0200, Heiner Kallweit wrote:
 
> Current situation means that PME is unusable on all systems where
> pcie_aspm_support_enabled() returns false, what is basically every
> system except EXPERT mode is enabled and CONFIG_PCIEASPM is set.
> So we definitely need to do something.

CONFIG_PCIEASPM is default y. I don't think there's huge value in 
adding complexity to deal with it being disabled, given that the kernel 
is then in a configuration that no vendor is testing against. There are 
existing runtime mechanisms to disable it at runtime.
 
-- 
Matthew Garrett | mjg59@srcf.ucam.org

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: Lost PCIe PME after a914ff2d78ce ("PCI/ASPM: Don't select CONFIG_PCIEASPM by default")
  2020-05-29 22:58               ` Matthew Garrett
@ 2020-05-30  6:33                 ` Heiner Kallweit
  2020-05-30  7:14                   ` Matthew Garrett
  0 siblings, 1 reply; 15+ messages in thread
From: Heiner Kallweit @ 2020-05-30  6:33 UTC (permalink / raw)
  To: Matthew Garrett, Bjorn Helgaas, Bjorn Helgaas
  Cc: Rafael J. Wysocki, linux-pci, linux-kernel, linux-acpi

On 30.05.2020 00:58, Matthew Garrett wrote:
> On Sat, May 30, 2020 at 12:26:17AM +0200, Heiner Kallweit wrote:
>  
>> Current situation means that PME is unusable on all systems where
>> pcie_aspm_support_enabled() returns false, what is basically every
>> system except EXPERT mode is enabled and CONFIG_PCIEASPM is set.
>> So we definitely need to do something.
> 
> CONFIG_PCIEASPM is default y. I don't think there's huge value in 
> adding complexity to deal with it being disabled, given that the kernel 
> is then in a configuration that no vendor is testing against. There are 
> existing runtime mechanisms to disable it at runtime.
>  
> 
It *was* default y. This changed with a914ff2d78ce ("PCI/ASPM: Don't
select CONFIG_PCIEASPM by default") and that's what triggered the
problem. If there's no easy solution, then maybe it's best to revert
the change for now.

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: Lost PCIe PME after a914ff2d78ce ("PCI/ASPM: Don't select CONFIG_PCIEASPM by default")
  2020-05-30  6:33                 ` Heiner Kallweit
@ 2020-05-30  7:14                   ` Matthew Garrett
  2020-05-30 11:33                     ` Christoph Hellwig
  0 siblings, 1 reply; 15+ messages in thread
From: Matthew Garrett @ 2020-05-30  7:14 UTC (permalink / raw)
  To: Heiner Kallweit
  Cc: Bjorn Helgaas, Bjorn Helgaas, Rafael J. Wysocki, linux-pci,
	linux-kernel, linux-acpi

On Sat, May 30, 2020 at 08:33:50AM +0200, Heiner Kallweit wrote:

> It *was* default y. This changed with a914ff2d78ce ("PCI/ASPM: Don't
> select CONFIG_PCIEASPM by default") and that's what triggered the
> problem. If there's no easy solution, then maybe it's best to revert
> the change for now.

Oh, sorry, I was looking at mainline. CONFIG_PCIEASPM should 
*definitely* be enabled by default - platforms expect the OS to support 
it. If we want to get rid of default y then I think it'd make more sense 
to have a CONFIG_DISABLE_PCIEASPM that's under EXPERT, and people who 
really want to disable the code can do so.
 
-- 
Matthew Garrett | mjg59@srcf.ucam.org

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: Lost PCIe PME after a914ff2d78ce ("PCI/ASPM: Don't select CONFIG_PCIEASPM by default")
  2020-05-30  7:14                   ` Matthew Garrett
@ 2020-05-30 11:33                     ` Christoph Hellwig
  2020-06-01 10:58                       ` Rafael J. Wysocki
  2020-06-01 15:13                       ` Bjorn Helgaas
  0 siblings, 2 replies; 15+ messages in thread
From: Christoph Hellwig @ 2020-05-30 11:33 UTC (permalink / raw)
  To: Matthew Garrett
  Cc: Heiner Kallweit, Bjorn Helgaas, Bjorn Helgaas, Rafael J. Wysocki,
	linux-pci, linux-kernel, linux-acpi

On Sat, May 30, 2020 at 08:14:34AM +0100, Matthew Garrett wrote:
> On Sat, May 30, 2020 at 08:33:50AM +0200, Heiner Kallweit wrote:
> 
> > It *was* default y. This changed with a914ff2d78ce ("PCI/ASPM: Don't
> > select CONFIG_PCIEASPM by default") and that's what triggered the
> > problem. If there's no easy solution, then maybe it's best to revert
> > the change for now.
> 
> Oh, sorry, I was looking at mainline. CONFIG_PCIEASPM should 
> *definitely* be enabled by default - platforms expect the OS to support 
> it. If we want to get rid of default y then I think it'd make more sense 
> to have a CONFIG_DISABLE_PCIEASPM that's under EXPERT, and people who 
> really want to disable the code can do so.

I think the fact that the EXPERT didn't get removed in the above bug
is a defintive bug.  But I'd go further and think the CONFIG_PCIEASPM
option should be removed entirely.  There is absolutely no good reason
to not build this small amount of code if PCIe support is enabled.

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: Lost PCIe PME after a914ff2d78ce ("PCI/ASPM: Don't select CONFIG_PCIEASPM by default")
  2020-05-30 11:33                     ` Christoph Hellwig
@ 2020-06-01 10:58                       ` Rafael J. Wysocki
  2020-06-01 15:13                       ` Bjorn Helgaas
  1 sibling, 0 replies; 15+ messages in thread
From: Rafael J. Wysocki @ 2020-06-01 10:58 UTC (permalink / raw)
  To: Christoph Hellwig
  Cc: Matthew Garrett, Heiner Kallweit, Bjorn Helgaas, Bjorn Helgaas,
	Rafael J. Wysocki, linux-pci, Linux Kernel Mailing List,
	ACPI Devel Maling List

On Sat, May 30, 2020 at 1:34 PM Christoph Hellwig <hch@infradead.org> wrote:
>
> On Sat, May 30, 2020 at 08:14:34AM +0100, Matthew Garrett wrote:
> > On Sat, May 30, 2020 at 08:33:50AM +0200, Heiner Kallweit wrote:
> >
> > > It *was* default y. This changed with a914ff2d78ce ("PCI/ASPM: Don't
> > > select CONFIG_PCIEASPM by default") and that's what triggered the
> > > problem. If there's no easy solution, then maybe it's best to revert
> > > the change for now.
> >
> > Oh, sorry, I was looking at mainline. CONFIG_PCIEASPM should
> > *definitely* be enabled by default - platforms expect the OS to support
> > it. If we want to get rid of default y then I think it'd make more sense
> > to have a CONFIG_DISABLE_PCIEASPM that's under EXPERT, and people who
> > really want to disable the code can do so.
>
> I think the fact that the EXPERT didn't get removed in the above bug
> is a defintive bug.  But I'd go further and think the CONFIG_PCIEASPM
> option should be removed entirely.  There is absolutely no good reason
> to not build this small amount of code if PCIe support is enabled.

Well stated, thanks!

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: Lost PCIe PME after a914ff2d78ce ("PCI/ASPM: Don't select CONFIG_PCIEASPM by default")
  2020-05-30 11:33                     ` Christoph Hellwig
  2020-06-01 10:58                       ` Rafael J. Wysocki
@ 2020-06-01 15:13                       ` Bjorn Helgaas
  1 sibling, 0 replies; 15+ messages in thread
From: Bjorn Helgaas @ 2020-06-01 15:13 UTC (permalink / raw)
  To: Christoph Hellwig
  Cc: Matthew Garrett, Heiner Kallweit, Bjorn Helgaas,
	Rafael J. Wysocki, linux-pci, linux-kernel, linux-acpi

On Sat, May 30, 2020 at 04:33:44AM -0700, Christoph Hellwig wrote:
> On Sat, May 30, 2020 at 08:14:34AM +0100, Matthew Garrett wrote:
> > On Sat, May 30, 2020 at 08:33:50AM +0200, Heiner Kallweit wrote:
> > 
> > > It *was* default y. This changed with a914ff2d78ce ("PCI/ASPM: Don't
> > > select CONFIG_PCIEASPM by default") and that's what triggered the
> > > problem. If there's no easy solution, then maybe it's best to revert
> > > the change for now.
> > 
> > Oh, sorry, I was looking at mainline. CONFIG_PCIEASPM should 
> > *definitely* be enabled by default - platforms expect the OS to support 
> > it. If we want to get rid of default y then I think it'd make more sense 
> > to have a CONFIG_DISABLE_PCIEASPM that's under EXPERT, and people who 
> > really want to disable the code can do so.
> 
> I think the fact that the EXPERT didn't get removed in the above bug
> is a defintive bug.  But I'd go further and think the CONFIG_PCIEASPM
> option should be removed entirely.  There is absolutely no good reason
> to not build this small amount of code if PCIe support is enabled.

That might be a good solution.  I don't really want a situation where
leaving CONFIG_PCIEASPM unset is "known to break PME."

ASPM support has historically been fragile, and it's actually a
significant amount of code (~10KB on my x86), which is larger than
many other things for which we have config options.  But we do have
boot-time and run-time ways to disable it.

Another possibility might be to make it so Linux always advertises
ASPM support, but doesn't actually *do* anything unless
CONFIG_PCIEASPM is set.  I don't think advertising ASPM support means
the OS is required to change whatever configuration firmware did.

Bjorn

^ permalink raw reply	[flat|nested] 15+ messages in thread

end of thread, other threads:[~2020-06-01 15:13 UTC | newest]

Thread overview: 15+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-05-28 21:44 Lost PCIe PME after a914ff2d78ce ("PCI/ASPM: Don't select CONFIG_PCIEASPM by default") Heiner Kallweit
2020-05-29 18:50 ` Heiner Kallweit
2020-05-29 19:21   ` Bjorn Helgaas
2020-05-29 19:40     ` Heiner Kallweit
2020-05-29 20:09       ` Heiner Kallweit
2020-05-29 20:21         ` Bjorn Helgaas
2020-05-29 20:53           ` Heiner Kallweit
2020-05-29 20:59           ` Matthew Garrett
2020-05-29 22:26             ` Heiner Kallweit
2020-05-29 22:58               ` Matthew Garrett
2020-05-30  6:33                 ` Heiner Kallweit
2020-05-30  7:14                   ` Matthew Garrett
2020-05-30 11:33                     ` Christoph Hellwig
2020-06-01 10:58                       ` Rafael J. Wysocki
2020-06-01 15:13                       ` Bjorn Helgaas

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.