From: AKASHI Takahiro <takahiro.akashi@linaro.org>
To: Adrian Hunter <adrian.hunter@intel.com>
Cc: ulf.hansson@linaro.org, linux-mmc@vger.kernel.org,
linux-kernel@vger.kernel.org, ben.chuang@genesyslogic.com.tw,
greg.tu@genesyslogic.com.tw
Subject: Re: [RFC PATCH v3.1 09/27] mmc: sdhci: add UHS-II related definitions in headers
Date: Mon, 30 Nov 2020 14:21:20 +0900 [thread overview]
Message-ID: <20201130052120.GB48535@laputa> (raw)
In-Reply-To: <aa8b2aab-51c0-9757-276b-f36dd5d33679@intel.com>
On Thu, Nov 26, 2020 at 10:15:29AM +0200, Adrian Hunter wrote:
> On 6/11/20 4:27 am, AKASHI Takahiro wrote:
> > Add UHS-II related definitions in shdci.h and sdhci-uhs2.h.
> >
> > Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
> > Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
> > ---
> > drivers/mmc/host/sdhci-uhs2.h | 210 ++++++++++++++++++++++++++++++++++
> > drivers/mmc/host/sdhci.h | 73 +++++++++++-
> > 2 files changed, 282 insertions(+), 1 deletion(-)
> > create mode 100644 drivers/mmc/host/sdhci-uhs2.h
> >
> > diff --git a/drivers/mmc/host/sdhci-uhs2.h b/drivers/mmc/host/sdhci-uhs2.h
> > new file mode 100644
> > index 000000000000..3b157df9c89c
> > --- /dev/null
> > +++ b/drivers/mmc/host/sdhci-uhs2.h
> > @@ -0,0 +1,210 @@
> > +/* SPDX-License-Identifier: GPL-2.0-or-later */
> > +/*
> > + * linux/drivers/mmc/host/sdhci-uhs2.h - Secure Digital Host Controller
> > + * Interface driver
> > + *
> > + * Header file for Host Controller UHS2 related registers and I/O accessors.
> > + *
> > + * Copyright (C) 2014 Intel Corp, All Rights Reserved.
> > + */
> > +#ifndef __SDHCI_UHS2_H
> > +#define __SDHCI_UHS2_H
> > +
> > +#include <linux/bits.h>
> > +
> > +/*
> > + * UHS-II Controller registers
> > + * 0x74 preset in sdhci.h
> > + * 0x80
> > + * 0x84-0xB4
> > + * 0xB8-0xCF
> > + * 0xE0-0xE7
> > + */
> > +/* UHS2 */
> > +#define SDHCI_UHS2_BLOCK_SIZE 0x80
> > +#define SDHCI_UHS2_MAKE_BLKSZ(dma, blksz) \
> > + ((((dma) & 0x7) << 12) | ((blksz) & 0xFFF))
> > +
> > +#define SDHCI_UHS2_BLOCK_COUNT 0x84
> > +
> > +#define SDHCI_UHS2_CMD_PACKET 0x88
> > +#define SDHCI_UHS2_CMD_PACK_MAX_LEN 20
> > +
> > +#define SDHCI_UHS2_TRANS_MODE 0x9C
> > +#define SDHCI_UHS2_TRNS_DMA BIT(0)
> > +#define SDHCI_UHS2_TRNS_BLK_CNT_EN BIT(1)
> > +#define SDHCI_UHS2_TRNS_DATA_TRNS_WRT BIT(4)
> > +#define SDHCI_UHS2_TRNS_BLK_BYTE_MODE BIT(5)
> > +#define SDHCI_UHS2_TRNS_RES_R5 BIT(6)
> > +#define SDHCI_UHS2_TRNS_RES_ERR_CHECK_EN BIT(7)
> > +#define SDHCI_UHS2_TRNS_RES_INT_DIS BIT(8)
> > +#define SDHCI_UHS2_TRNS_WAIT_EBSY BIT(14)
> > +#define SDHCI_UHS2_TRNS_2L_HD BIT(15)
> > +
> > +#define SDHCI_UHS2_COMMAND 0x9E
> > +#define SDHCI_UHS2_COMMAND_SUB_CMD 0x0004
> > +#define SDHCI_UHS2_COMMAND_DATA 0x0020
> > +#define SDHCI_UHS2_COMMAND_TRNS_ABORT 0x0040
> > +#define SDHCI_UHS2_COMMAND_CMD12 0x0080
> > +#define SDHCI_UHS2_COMMAND_DORMANT 0x00C0
> > +#define SDHCI_UHS2_COMMAND_PACK_LEN_MASK GENMASK(12,8)
> > +#define SDHCI_UHS2_COMMAND_PACK_LEN_SHIFT 8
> > +
> > +#define SDHCI_UHS2_RESPONSE 0xA0
> > +#define SDHCI_UHS2_RESPONSE_MAX_LEN 20
> > +
> > +#define SDHCI_UHS2_MSG_SELECT 0xB4
> > +#define SDHCI_UHS2_MSG_SELECT_CURR 0x0
> > +#define SDHCI_UHS2_MSG_SELECT_ONE 0x1
> > +#define SDHCI_UHS2_MSG_SELECT_TWO 0x2
> > +#define SDHCI_UHS2_MSG_SELECT_THREE 0x3
> > +
> > +#define SDHCI_UHS2_MSG 0xB8
> > +
> > +#define SDHCI_UHS2_DEV_INT_STATUS 0xBC
> > +
> > +#define SDHCI_UHS2_DEV_SELECT 0xBE
> > +#define SDHCI_UHS2_DEV_SELECT_DEV_SEL_MASK GENMASK(3,0)
> > +#define SDHCI_UHS2_DEV_SELECT_INT_MSG_EN BIT(7)
> > +
> > +#define SDHCI_UHS2_DEV_INT_CODE 0xBF
> > +
> > +#define SDHCI_UHS2_SW_RESET 0xC0
> > +#define SDHCI_UHS2_SW_RESET_FULL 0x0001
> > +#define SDHCI_UHS2_SW_RESET_SD 0x0002
> > +
> > +#define SDHCI_UHS2_TIMER_CTRL 0xC2
> > +#define SDHCI_UHS2_TIMER_CTRL_DEADLOCK_SHIFT 4
> > +
> > +#define SDHCI_UHS2_ERR_INT_STATUS 0xC4
> > +#define SDHCI_UHS2_ERR_INT_STATUS_EN 0xC8
> > +#define SDHCI_UHS2_ERR_INT_SIG_EN 0xCC
> > +#define SDHCI_UHS2_ERR_INT_STATUS_HEADER BIT(0)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_RES BIT(1)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP BIT(2)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_CRC BIT(3)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_FRAME BIT(4)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_TID BIT(5)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER BIT(7)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_EBUSY BIT(8)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_ADMA BIT(15)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT BIT(16)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT BIT(17)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_VENDOR BIT(27)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_MASK \
> > + (SDHCI_UHS2_ERR_INT_STATUS_HEADER | \
> > + SDHCI_UHS2_ERR_INT_STATUS_RES | \
> > + SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP | \
> > + SDHCI_UHS2_ERR_INT_STATUS_CRC | \
> > + SDHCI_UHS2_ERR_INT_STATUS_FRAME | \
> > + SDHCI_UHS2_ERR_INT_STATUS_TID | \
> > + SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER | \
> > + SDHCI_UHS2_ERR_INT_STATUS_EBUSY | \
> > + SDHCI_UHS2_ERR_INT_STATUS_ADMA | \
> > + SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT | \
> > + SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_CMD_MASK \
> > + (SDHCI_UHS2_ERR_INT_STATUS_HEADER | \
> > + SDHCI_UHS2_ERR_INT_STATUS_RES | \
> > + SDHCI_UHS2_ERR_INT_STATUS_FRAME | \
> > + SDHCI_UHS2_ERR_INT_STATUS_TID | \
> > + SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT)
> > +/* CRC Error occurs during a packet receiving */
> > +#define SDHCI_UHS2_ERR_INT_STATUS_DATA_MASK \
> > + (SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP | \
> > + SDHCI_UHS2_ERR_INT_STATUS_CRC | \
> > + SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER | \
> > + SDHCI_UHS2_ERR_INT_STATUS_EBUSY | \
> > + SDHCI_UHS2_ERR_INT_STATUS_ADMA | \
> > + SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT)
> > +
> > +#define SDHCI_UHS2_SET_PTR 0xE0
> > +#define SDHCI_UHS2_GEN_SET_POWER_LOW 0x0001
> > +#define SDHCI_UHS2_GEN_SET_N_LANES_POS 8
> > +#define SDHCI_UHS2_GEN_SET_2L_FD_HD 0x0
> > +#define SDHCI_UHS2_GEN_SET_2D1U_FD 0x2
> > +#define SDHCI_UHS2_GEN_SET_1D2U_FD 0x3
> > +#define SDHCI_UHS2_GEN_SET_2D2U_FD 0x4
> > +
> > +#define SDHCI_UHS2_PHY_SET_SPEED_POS 6
> > +#define SDHCI_UHS2_PHY_SET_HIBER_EN BIT(12)
> > +#define SDHCI_UHS2_PHY_SET_N_LSS_SYN_MASK GENMASK(19,16)
> > +#define SDHCI_UHS2_PHY_SET_N_LSS_SYN_POS 16
> > +#define SDHCI_UHS2_PHY_SET_N_LSS_DIR_MASK GENMASK(23,20)
> > +#define SDHCI_UHS2_PHY_SET_N_LSS_DIR_POS 20
> > +
> > +#define SDHCI_UHS2_TRAN_SET_N_FCU_MASK GENMASK(15,8)
> > +#define SDHCI_UHS2_TRAN_SET_N_FCU_POS 8
> > +#define SDHCI_UHS2_TRAN_SET_RETRY_CNT_MASK GENMASK(17,16)
> > +#define SDHCI_UHS2_TRAN_SET_RETRY_CNT_POS 16
> > +
> > +#define SDHCI_UHS2_TRAN_SET_1_N_DAT_GAP_MASK GENMASK(7,0)
> > +
> > +#define SDHCI_UHS2_HOST_CAPS_PTR 0xE2
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_OFFSET 0
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_DAP_MASK GENMASK(3,0)
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_GAP_MASK GENMASK(7,4)
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_GAP(gap) ((gap) * 360)
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_GAP_SHIFT 4
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_LANE_MASK GENMASK(13,8)
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_LANE_SHIFT 8
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_2L_HD_FD 1
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_2D1U_FD 2
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_1D2U_FD 4
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_2D2U_FD 8
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_ADDR_64 BIT(14)
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_BOOT BIT(15)
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_MASK GENMASK(17,16)
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_SHIFT 16
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_RMV 0
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_EMB 1
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_EMB_RMV 2
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_NUM_DEV_MASK GENMASK(21,18)
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_NUM_DEV_SHIFT 18
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_MASK GENMASK(23,22)
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_SHIFT 22
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_P2P 0
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_RING 1
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_HUB 2
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_HUB_RING 3
> > +
> > +#define SDHCI_UHS2_HOST_CAPS_PHY_OFFSET 4
> > +#define SDHCI_UHS2_HOST_CAPS_PHY_REV_MASK GENMASK(5,0)
> > +#define SDHCI_UHS2_HOST_CAPS_PHY_RANGE_MASK GENMASK(7,6)
> > +#define SDHCI_UHS2_HOST_CAPS_PHY_RANGE_SHIFT 6
> > +#define SDHCI_UHS2_HOST_CAPS_PHY_RANGE_A 0
> > +#define SDHCI_UHS2_HOST_CAPS_PHY_RANGE_B 1
> > +#define SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_SYN_MASK GENMASK(19,16)
> > +#define SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_SYN_SHIFT 16
> > +#define SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_DIR_MASK GENMASK(23,20)
> > +#define SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_DIR_SHIFT 20
> > +#define SDHCI_UHS2_HOST_CAPS_TRAN_OFFSET 8
> > +#define SDHCI_UHS2_HOST_CAPS_TRAN_LINK_REV_MASK GENMASK(5,0)
> > +#define SDHCI_UHS2_HOST_CAPS_TRAN_N_FCU_MASK GENMASK(15,8)
> > +#define SDHCI_UHS2_HOST_CAPS_TRAN_N_FCU_SHIFT 8
> > +#define SDHCI_UHS2_HOST_CAPS_TRAN_HOST_TYPE_MASK GENMASK(18,16)
> > +#define SDHCI_UHS2_HOST_CAPS_TRAN_HOST_TYPE_SHIFT 16
> > +#define SDHCI_UHS2_HOST_CAPS_TRAN_BLK_LEN_MASK GENMASK(31,20)
> > +#define SDHCI_UHS2_HOST_CAPS_TRAN_BLK_LEN_SHIFT 20
> > +
> > +#define SDHCI_UHS2_HOST_CAPS_TRAN_1_OFFSET 12
> > +#define SDHCI_UHS2_HOST_CAPS_TRAN_1_N_DATA_GAP_MASK GENMASK(7,0)
> > +
> > +#define SDHCI_UHS2_TEST_PTR 0xE4
> > +#define SDHCI_UHS2_TEST_ERR_HEADER BIT(0)
> > +#define SDHCI_UHS2_TEST_ERR_RES BIT(1)
> > +#define SDHCI_UHS2_TEST_ERR_RETRY_EXP BIT(2)
> > +#define SDHCI_UHS2_TEST_ERR_CRC BIT(3)
> > +#define SDHCI_UHS2_TEST_ERR_FRAME BIT(4)
> > +#define SDHCI_UHS2_TEST_ERR_TID BIT(5)
> > +#define SDHCI_UHS2_TEST_ERR_UNRECOVER BIT(7)
> > +#define SDHCI_UHS2_TEST_ERR_EBUSY BIT(8)
> > +#define SDHCI_UHS2_TEST_ERR_ADMA BIT(15)
> > +#define SDHCI_UHS2_TEST_ERR_RES_TIMEOUT BIT(16)
> > +#define SDHCI_UHS2_TEST_ERR_DEADLOCK_TIMEOUT BIT(17)
> > +#define SDHCI_UHS2_TEST_ERR_VENDOR BIT(27)
> > +
> > +#define SDHCI_UHS2_EMBED_CTRL 0xE6
> > +#define SDHCI_UHS2_VENDOR 0xE8
> > +
> > +#endif /* __SDHCI_UHS2_H */
> > diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
> > index 0770c036e2ff..d9d7a76cedc1 100644
> > --- a/drivers/mmc/host/sdhci.h
> > +++ b/drivers/mmc/host/sdhci.h
> > @@ -43,8 +43,27 @@
> > #define SDHCI_TRNS_READ 0x10
> > #define SDHCI_TRNS_MULTI 0x20
> >
> > +/*
> > + * Defined in Host Version 4.10.
> > + * 1 - R5 (SDIO)
> > + * 0 - R1 (Memory)
> > + */
> > +#define SDHCI_TRNS_RES_TYPE 0x40
> > +#define SDHCI_TRNS_RES_ERR_CHECK 0x80
> > +#define SDHCI_TRNS_RES_INT_DIS 0x0100
> > +
> > #define SDHCI_COMMAND 0x0E
> > #define SDHCI_CMD_RESP_MASK 0x03
> > +
> > +/*
> > + * Host Version 4.10 adds this bit to distinguish a main command or
> > + * sub command.
> > + * CMD53(SDIO) - main command
> > + * CMD52(SDIO) - sub command which doesn't have data block or doesn't
> > + * indicate busy.
> > + */
> > +#define SDHCI_CMD_SUB_CMD 0x04
> > +
> > #define SDHCI_CMD_CRC 0x08
> > #define SDHCI_CMD_INDEX 0x10
> > #define SDHCI_CMD_DATA 0x20
> > @@ -60,11 +79,19 @@
> >
> > #define SDHCI_RESPONSE 0x10
> >
> > +#define SDHCI_RESPONSE_CM_TRAN_ABORT_OFFSET 0x10
> > +#define SDHCI_RESPONSE_CM_TRAN_ABORT_SIZE 4
> > +#define SDHCI_RESPONSE_SD_TRAN_ABORT_OFFSET 0x18
> > +#define SDHCI_RESPONSE_SD_TRAN_ABORT_SIZE 8
>
> I would prefer to have all the UHS2 definitions in sdhci-uhs2. If they
> belong to an existing register, just put a comment saying what register.
I would disagree, but if you really want, I'd defer to you.
-Takahiro Akashi
>
> > +
> > #define SDHCI_BUFFER 0x20
> >
> > #define SDHCI_PRESENT_STATE 0x24
> > #define SDHCI_CMD_INHIBIT 0x00000001
> > #define SDHCI_DATA_INHIBIT 0x00000002
> > +
> > +#define SDHCI_DATA_HIGH_LVL_MASK 0x000000F0
> > +
> > #define SDHCI_DOING_WRITE 0x00000100
> > #define SDHCI_DOING_READ 0x00000200
> > #define SDHCI_SPACE_AVAILABLE 0x00000400
> > @@ -80,6 +107,13 @@
> > #define SDHCI_DATA_0_LVL_MASK 0x00100000
> > #define SDHCI_CMD_LVL 0x01000000
> >
> > +#define SDHCI_HOST_REGULATOR_STABLE 0x02000000
> > +#define SDHCI_CMD_NOT_ISSUE_ERR 0x08000000
> > +#define SDHCI_SUB_CMD_STATUS 0x10000000
> > +#define SDHCI_UHS2_IN_DORMANT_STATE 0x20000000
> > +#define SDHCI_UHS2_LANE_SYNC 0x40000000
> > +#define SDHCI_UHS2_IF_DETECT 0x80000000
> > +
> > #define SDHCI_HOST_CONTROL 0x28
> > #define SDHCI_CTRL_LED 0x01
> > #define SDHCI_CTRL_4BITBUS 0x02
> > @@ -100,6 +134,11 @@
> > #define SDHCI_POWER_300 0x0C
> > #define SDHCI_POWER_330 0x0E
> >
> > +/* VDD2 - UHS2 */
> > +#define SDHCI_VDD2_POWER_ON 0x10
> > +#define SDHCI_VDD2_POWER_180 0xA0
> > +#define SDHCI_VDD2_POWER_120 0x80
> > +
> > #define SDHCI_BLOCK_GAP_CONTROL 0x2A
> >
> > #define SDHCI_WAKE_UP_CONTROL 0x2B
> > @@ -110,7 +149,7 @@
> > #define SDHCI_CLOCK_CONTROL 0x2C
> > #define SDHCI_DIVIDER_SHIFT 8
> > #define SDHCI_DIVIDER_HI_SHIFT 6
> > -#define SDHCI_DIV_MASK 0xFF
> > +#define SDHCI_DIV_MASK 0xFF
> > #define SDHCI_DIV_MASK_LEN 8
> > #define SDHCI_DIV_HI_MASK 0x300
> > #define SDHCI_PROG_CLOCK_MODE 0x0020
> > @@ -139,6 +178,10 @@
> > #define SDHCI_INT_CARD_REMOVE 0x00000080
> > #define SDHCI_INT_CARD_INT 0x00000100
> > #define SDHCI_INT_RETUNE 0x00001000
> > +
> > +/* Host Version 4.10 */
> > +#define SDHCI_INT_FX_EVENT 0x00002000
> > +
> > #define SDHCI_INT_CQE 0x00004000
> > #define SDHCI_INT_ERROR 0x00008000
> > #define SDHCI_INT_TIMEOUT 0x00010000
> > @@ -152,6 +195,9 @@
> > #define SDHCI_INT_AUTO_CMD_ERR 0x01000000
> > #define SDHCI_INT_ADMA_ERROR 0x02000000
> >
> > +/* Host Version 4.0 */
> > +#define SDHCI_INT_RESPONSE_ERROR 0x08000000
> > +
> > #define SDHCI_INT_NORMAL_MASK 0x00007FFF
> > #define SDHCI_INT_ERROR_MASK 0xFFFF8000
> >
> > @@ -178,6 +224,9 @@
> > #define SDHCI_AUTO_CMD_END_BIT 0x00000008
> > #define SDHCI_AUTO_CMD_INDEX 0x00000010
> >
> > +/* Host Version 4.10 */
> > +#define SDHCI_ACMD_RESPONSE_ERROR 0x0020
> > +
> > #define SDHCI_HOST_CONTROL2 0x3E
> > #define SDHCI_CTRL_UHS_MASK 0x0007
> > #define SDHCI_CTRL_UHS_SDR12 0x0000
> > @@ -186,6 +235,7 @@
> > #define SDHCI_CTRL_UHS_SDR104 0x0003
> > #define SDHCI_CTRL_UHS_DDR50 0x0004
> > #define SDHCI_CTRL_HS400 0x0005 /* Non-standard */
> > +#define SDHCI_CTRL_UHS_2 0x0007 /* UHS-2 */
> > #define SDHCI_CTRL_VDD_180 0x0008
> > #define SDHCI_CTRL_DRV_TYPE_MASK 0x0030
> > #define SDHCI_CTRL_DRV_TYPE_B 0x0000
> > @@ -194,9 +244,12 @@
> > #define SDHCI_CTRL_DRV_TYPE_D 0x0030
> > #define SDHCI_CTRL_EXEC_TUNING 0x0040
> > #define SDHCI_CTRL_TUNED_CLK 0x0080
> > +#define SDHCI_CTRL_UHS2_INTERFACE_EN 0x0100 /* UHS-2 */
> > +#define SDHCI_CTRL_ADMA2_LEN_MODE 0x0400
> > #define SDHCI_CMD23_ENABLE 0x0800
> > #define SDHCI_CTRL_V4_MODE 0x1000
> > #define SDHCI_CTRL_64BIT_ADDR 0x2000
> > +#define SDHCI_CTRL_ASYNC_INT_EN 0x4000
> > #define SDHCI_CTRL_PRESET_VAL_ENABLE 0x8000
> >
> > #define SDHCI_CAPABILITIES 0x40
> > @@ -217,11 +270,13 @@
> > #define SDHCI_CAN_VDD_180 0x04000000
> > #define SDHCI_CAN_64BIT_V4 0x08000000
> > #define SDHCI_CAN_64BIT 0x10000000
> > +#define SDHCI_CAN_ASYNC_INT 0x20000000
> >
> > #define SDHCI_CAPABILITIES_1 0x44
> > #define SDHCI_SUPPORT_SDR50 0x00000001
> > #define SDHCI_SUPPORT_SDR104 0x00000002
> > #define SDHCI_SUPPORT_DDR50 0x00000004
> > +#define SDHCI_SUPPORT_UHS2 0x00000008 /* UHS-2 support */
> > #define SDHCI_DRIVER_TYPE_A 0x00000010
> > #define SDHCI_DRIVER_TYPE_C 0x00000020
> > #define SDHCI_DRIVER_TYPE_D 0x00000040
> > @@ -230,19 +285,28 @@
> > #define SDHCI_RETUNING_MODE_MASK GENMASK(15, 14)
> > #define SDHCI_CLOCK_MUL_MASK GENMASK(23, 16)
> > #define SDHCI_CAN_DO_ADMA3 0x08000000
> > +#define SDHCI_SUPPORT_VDD2_180 0x10000000 /* UHS-2 1.8V VDD2 */
> > +#define SDHCI_RSVD_FOR_VDD2 0x20000000 /* Rsvd for future VDD2 */
> > #define SDHCI_SUPPORT_HS400 0x80000000 /* Non-standard */
> >
> > #define SDHCI_MAX_CURRENT 0x48
> > +#define SDHCI_MAX_CURRENT_1 0x4C
> > #define SDHCI_MAX_CURRENT_LIMIT GENMASK(7, 0)
> > #define SDHCI_MAX_CURRENT_330_MASK GENMASK(7, 0)
> > #define SDHCI_MAX_CURRENT_300_MASK GENMASK(15, 8)
> > #define SDHCI_MAX_CURRENT_180_MASK GENMASK(23, 16)
> > +#define SDHCI_MAX_CURRENT_VDD2_180_MASK GENMASK(7, 0) /* UHS2 */
> > #define SDHCI_MAX_CURRENT_MULTIPLIER 4
> >
> > /* 4C-4F reserved for more max current */
> >
> > #define SDHCI_SET_ACMD12_ERROR 0x50
> > +/* Host Version 4.10 */
> > +#define SDHCI_SET_ACMD_RESPONSE_ERROR 0x20
> > #define SDHCI_SET_INT_ERROR 0x52
> > +/* Host Version 4.10 */
> > +#define SDHCI_SET_INT_TUNING_ERROR 0x0400
> > +#define SDHCI_SET_INT_RESPONSE_ERROR 0x0800
> >
> > #define SDHCI_ADMA_ERROR 0x54
> >
> > @@ -259,10 +323,16 @@
> > #define SDHCI_PRESET_FOR_SDR104 0x6C
> > #define SDHCI_PRESET_FOR_DDR50 0x6E
> > #define SDHCI_PRESET_FOR_HS400 0x74 /* Non-standard */
> > +
> > +/* TODO: 0x74 is used for UHS2 in 4.10. How about HS400? */
> > +/* UHS2 */
> > +#define SDHCI_PRESET_FOR_UHS2 0x74
> > #define SDHCI_PRESET_DRV_MASK GENMASK(15, 14)
> > #define SDHCI_PRESET_CLKGEN_SEL BIT(10)
> > #define SDHCI_PRESET_SDCLK_FREQ_MASK GENMASK(9, 0)
> >
> > +#define SDHCI_ADMA3_ADDRESS 0x78
> > +
> > #define SDHCI_SLOT_INT_STATUS 0xFC
> >
> > #define SDHCI_HOST_VERSION 0xFE
> > @@ -652,6 +722,7 @@ struct sdhci_ops {
> > void (*request_done)(struct sdhci_host *host,
> > struct mmc_request *mrq);
> > void (*dump_vendor_regs)(struct sdhci_host *host);
> > + void (*dump_uhs2_regs)(struct sdhci_host *host);
> > };
> >
> > #ifdef CONFIG_MMC_SDHCI_IO_ACCESSORS
> >
>
next prev parent reply other threads:[~2020-11-30 5:22 UTC|newest]
Thread overview: 74+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-11-06 2:26 [RFC PATCH v3.1 00/27] Add support UHS-II for GL9755 AKASHI Takahiro
2020-11-06 2:27 ` [RFC PATCH v3.1 01/27] mmc: add UHS-II related definitions in public headers AKASHI Takahiro
2020-11-06 2:27 ` [RFC PATCH v3.1 02/27] mmc: core: UHS-II support, modify power-up sequence AKASHI Takahiro
2020-11-06 2:27 ` [RFC PATCH v3.1 03/27] mmc: core: UHS-II support, skip set_chip_select() AKASHI Takahiro
2020-11-10 7:15 ` Bough Chen
2020-11-06 2:27 ` [RFC PATCH v3.1 04/27] mmc: core: UHS-II support, try to select UHS-II interface AKASHI Takahiro
2020-11-06 4:24 ` kernel test robot
2020-11-06 2:27 ` [RFC PATCH v3.1 05/27] mmc: core: UHS-II support, skip TMODE setup in some cases AKASHI Takahiro
2020-11-06 2:27 ` [RFC PATCH v3.1 06/27] mmc: core: UHS-II support, generate UHS-II SD command packet AKASHI Takahiro
2020-11-06 2:27 ` [RFC PATCH v3.1 07/27] mmc: core: UHS-II support, set APP_CMD bit if necessary AKASHI Takahiro
2020-11-06 2:27 ` [RFC PATCH v3.1 08/27] mmc: sdhci: add a kernel configuration for enabling UHS-II support AKASHI Takahiro
2020-11-26 8:14 ` Adrian Hunter
2020-11-30 5:17 ` AKASHI Takahiro
2020-11-06 2:27 ` [RFC PATCH v3.1 09/27] mmc: sdhci: add UHS-II related definitions in headers AKASHI Takahiro
2020-11-26 8:15 ` Adrian Hunter
2020-11-30 5:21 ` AKASHI Takahiro [this message]
2020-11-06 2:27 ` [RFC PATCH v3.1 10/27] mmc: sdhci: add UHS-II module AKASHI Takahiro
2020-11-06 2:27 ` [RFC PATCH v3.1 11/27] mmc: sdhci-uhs2: dump UHS-II registers AKASHI Takahiro
2020-11-06 2:27 ` [RFC PATCH v3.1 12/27] mmc: sdhci-uhs2: add reset function AKASHI Takahiro
2020-11-26 8:16 ` Adrian Hunter
2020-11-30 6:20 ` AKASHI Takahiro
2020-11-30 7:37 ` Adrian Hunter
2020-11-06 2:27 ` [RFC PATCH v3.1 13/27] mmc: sdhci-uhs2: add set_power() to support vdd2 AKASHI Takahiro
2020-11-06 8:11 ` kernel test robot
2020-11-26 8:16 ` Adrian Hunter
2020-11-30 7:15 ` AKASHI Takahiro
2020-11-30 7:44 ` Adrian Hunter
2020-11-06 2:27 ` [RFC PATCH v3.1 14/27] mmc: sdhci-uhs2: skip signal_voltage_switch() AKASHI Takahiro
2020-11-26 8:16 ` Adrian Hunter
2020-11-30 7:38 ` AKASHI Takahiro
2020-11-06 2:27 ` [RFC PATCH v3.1 15/27] mmc: sdhci-uhs2: add set_timeout() AKASHI Takahiro
2020-11-06 2:27 ` [RFC PATCH v3.1 16/27] mmc: sdhci-uhs2: add set_ios() AKASHI Takahiro
2020-11-06 4:06 ` kernel test robot
2020-11-06 8:40 ` kernel test robot
2020-11-26 8:17 ` Adrian Hunter
2020-11-30 7:51 ` AKASHI Takahiro
2020-12-03 9:51 ` Adrian Hunter
2020-11-06 2:27 ` [RFC PATCH v3.1 17/27] mmc: sdhci-uhs2: add detect_init() to detect the interface AKASHI Takahiro
2020-11-26 8:17 ` Adrian Hunter
2020-12-01 2:25 ` AKASHI Takahiro
2020-11-06 2:27 ` [RFC PATCH v3.1 18/27] mmc: sdhci-uhs2: add clock operations AKASHI Takahiro
2020-11-26 8:17 ` Adrian Hunter
2020-12-01 2:27 ` AKASHI Takahiro
2020-11-06 2:27 ` [RFC PATCH v3.1 19/27] mmc: sdhci-uhs2: add set_reg() to initialise the interface AKASHI Takahiro
2020-11-26 8:18 ` Adrian Hunter
2020-12-01 2:28 ` AKASHI Takahiro
2020-11-06 2:27 ` [RFC PATCH v3.1 20/27] mmc: sdhci-uhs2: add request() and others AKASHI Takahiro
2020-11-06 4:47 ` kernel test robot
2020-11-26 8:18 ` Adrian Hunter
2020-12-01 2:40 ` AKASHI Takahiro
2020-12-01 11:24 ` Adrian Hunter
2020-11-06 2:27 ` [RFC PATCH v3.1 21/27] mmc: sdhci-uhs2: add irq() " AKASHI Takahiro
2020-12-01 16:46 ` Adrian Hunter
2020-12-08 7:37 ` AKASHI Takahiro
2020-12-08 8:37 ` Adrian Hunter
2020-11-06 2:27 ` [RFC PATCH v3.1 22/27] mmc: sdhci-uhs2: add add_host() and others to set up the driver AKASHI Takahiro
2020-12-03 9:42 ` Adrian Hunter
2020-12-08 7:42 ` AKASHI Takahiro
2020-11-06 2:27 ` [RFC PATCH v3.1 23/27] mmc: sdhci-uhs2: add pre-detect_init hook AKASHI Takahiro
2020-11-06 2:27 ` [RFC PATCH v3.1 24/27] mmc: core: add post-mmc_attach_sd hook AKASHI Takahiro
2020-11-06 2:27 ` [RFC PATCH v3.1 25/27] mmc: sdhci-uhs2: " AKASHI Takahiro
2020-11-06 2:27 ` [RFC PATCH v3.1 26/27] mmc: sdhci-pci: add UHS-II support framework AKASHI Takahiro
2020-11-06 2:27 ` [RFC PATCH v3.1 27/27] mmc: sdhci-pci-gli: enable UHS-II mode for GL9755 AKASHI Takahiro
2020-11-06 4:47 ` kernel test robot
2020-11-09 4:38 ` kernel test robot
2020-11-25 7:41 ` [RFC PATCH v3.1 00/27] Add support UHS-II " AKASHI Takahiro
2020-11-25 10:43 ` Ulf Hansson
2020-11-26 0:06 ` AKASHI Takahiro
2020-11-26 8:18 ` Adrian Hunter
2020-12-01 3:09 ` AKASHI Takahiro
2020-12-03 9:55 ` Adrian Hunter
2020-12-08 7:58 ` AKASHI Takahiro
2020-12-08 8:48 ` Adrian Hunter
2020-12-03 10:02 ` Adrian Hunter
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201130052120.GB48535@laputa \
--to=takahiro.akashi@linaro.org \
--cc=adrian.hunter@intel.com \
--cc=ben.chuang@genesyslogic.com.tw \
--cc=greg.tu@genesyslogic.com.tw \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=ulf.hansson@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.