From: Amelie Delaunay <amelie.delaunay@foss.st.com> To: Kishon Vijay Abraham I <kishon@ti.com>, Vinod Koul <vkoul@kernel.org>, Rob Herring <robh+dt@kernel.org>, Alexandre Torgue <alexandre.torgue@foss.st.com>, Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: <linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>, <linux-arm-kernel@lists.infradead.org>, <linux-stm32@st-md-mailman.stormreply.com>, Amelie Delaunay <amelie.delaunay@foss.st.com> Subject: [PATCH v2 2/6] phy: stm32: manage 1v1 and 1v8 supplies at pll activation/deactivation Date: Tue, 5 Jan 2021 10:05:21 +0100 [thread overview] Message-ID: <20210105090525.23164-3-amelie.delaunay@foss.st.com> (raw) In-Reply-To: <20210105090525.23164-1-amelie.delaunay@foss.st.com> PLL block requires to be powered with 1v1 and 1v8 supplies to catch ENABLE signal. Currently, supplies are managed through phy_ops .power_on/off, and PLL activation/deactivation is managed through phy_ops .init/exit. The sequence of phy_ops .power_on/.phy_init, .power_off/.exit is USB drivers dependent. To ensure a good behavior of the PLL, supplies have to be managed at PLL activation/deactivation. That means the supplies need to be put in usbphyc node and not in phy children nodes. Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com> --- drivers/phy/st/phy-stm32-usbphyc.c | 102 +++++++++++++---------------- 1 file changed, 46 insertions(+), 56 deletions(-) diff --git a/drivers/phy/st/phy-stm32-usbphyc.c b/drivers/phy/st/phy-stm32-usbphyc.c index a54317e96c41..c78a2c7947ce 100644 --- a/drivers/phy/st/phy-stm32-usbphyc.c +++ b/drivers/phy/st/phy-stm32-usbphyc.c @@ -58,7 +58,6 @@ struct pll_params { struct stm32_usbphyc_phy { struct phy *phy; struct stm32_usbphyc *usbphyc; - struct regulator_bulk_data supplies[NUM_SUPPLIES]; u32 index; bool active; }; @@ -70,6 +69,7 @@ struct stm32_usbphyc { struct reset_control *rst; struct stm32_usbphyc_phy **phys; int nphys; + struct regulator_bulk_data supplies[NUM_SUPPLIES]; int switch_setup; }; @@ -153,10 +153,30 @@ static bool stm32_usbphyc_has_one_phy_active(struct stm32_usbphyc *usbphyc) return false; } +static int stm32_usbphyc_pll_disable(struct stm32_usbphyc *usbphyc) +{ + void __iomem *pll_reg = usbphyc->base + STM32_USBPHYC_PLL; + + /* Check if other phy port active */ + if (stm32_usbphyc_has_one_phy_active(usbphyc)) + return 0; + + stm32_usbphyc_clr_bits(pll_reg, PLLEN); + /* Wait for minimum width of powerdown pulse (ENABLE = Low) */ + udelay(PLL_PWR_DOWN_TIME_US); + + if (readl_relaxed(pll_reg) & PLLEN) { + dev_err(usbphyc->dev, "PLL not reset\n"); + return -EIO; + } + + return regulator_bulk_disable(NUM_SUPPLIES, usbphyc->supplies); +} + static int stm32_usbphyc_pll_enable(struct stm32_usbphyc *usbphyc) { void __iomem *pll_reg = usbphyc->base + STM32_USBPHYC_PLL; - bool pllen = (readl_relaxed(pll_reg) & PLLEN); + bool pllen = readl_relaxed(pll_reg) & PLLEN; int ret; /* Check if one phy port has already configured the pll */ @@ -164,46 +184,35 @@ static int stm32_usbphyc_pll_enable(struct stm32_usbphyc *usbphyc) return 0; if (pllen) { - stm32_usbphyc_clr_bits(pll_reg, PLLEN); - /* Wait for minimum width of powerdown pulse (ENABLE = Low) */ - udelay(PLL_PWR_DOWN_TIME_US); + ret = stm32_usbphyc_pll_disable(usbphyc); + if (ret) + return ret; } - ret = stm32_usbphyc_pll_init(usbphyc); + ret = regulator_bulk_enable(NUM_SUPPLIES, usbphyc->supplies); if (ret) return ret; - stm32_usbphyc_set_bits(pll_reg, PLLEN); + ret = stm32_usbphyc_pll_init(usbphyc); + if (ret) + goto reg_disable; + stm32_usbphyc_set_bits(pll_reg, PLLEN); /* Wait for maximum lock time */ udelay(PLL_LOCK_TIME_US); if (!(readl_relaxed(pll_reg) & PLLEN)) { dev_err(usbphyc->dev, "PLLEN not set\n"); - return -EIO; + ret = -EIO; + goto reg_disable; } return 0; -} - -static int stm32_usbphyc_pll_disable(struct stm32_usbphyc *usbphyc) -{ - void __iomem *pll_reg = usbphyc->base + STM32_USBPHYC_PLL; - - /* Check if other phy port active */ - if (stm32_usbphyc_has_one_phy_active(usbphyc)) - return 0; - stm32_usbphyc_clr_bits(pll_reg, PLLEN); - /* Wait for minimum width of powerdown pulse (ENABLE = Low) */ - udelay(PLL_PWR_DOWN_TIME_US); +reg_disable: + regulator_bulk_disable(NUM_SUPPLIES, usbphyc->supplies); - if (readl_relaxed(pll_reg) & PLLEN) { - dev_err(usbphyc->dev, "PLL not reset\n"); - return -EIO; - } - - return 0; + return ret; } static int stm32_usbphyc_phy_init(struct phy *phy) @@ -231,25 +240,9 @@ static int stm32_usbphyc_phy_exit(struct phy *phy) return stm32_usbphyc_pll_disable(usbphyc); } -static int stm32_usbphyc_phy_power_on(struct phy *phy) -{ - struct stm32_usbphyc_phy *usbphyc_phy = phy_get_drvdata(phy); - - return regulator_bulk_enable(NUM_SUPPLIES, usbphyc_phy->supplies); -} - -static int stm32_usbphyc_phy_power_off(struct phy *phy) -{ - struct stm32_usbphyc_phy *usbphyc_phy = phy_get_drvdata(phy); - - return regulator_bulk_disable(NUM_SUPPLIES, usbphyc_phy->supplies); -} - static const struct phy_ops stm32_usbphyc_phy_ops = { .init = stm32_usbphyc_phy_init, .exit = stm32_usbphyc_phy_exit, - .power_on = stm32_usbphyc_phy_power_on, - .power_off = stm32_usbphyc_phy_power_off, .owner = THIS_MODULE, }; @@ -313,7 +306,7 @@ static int stm32_usbphyc_probe(struct platform_device *pdev) struct device_node *child, *np = dev->of_node; struct phy_provider *phy_provider; u32 version; - int ret, port = 0; + int ret, i, port = 0; usbphyc = devm_kzalloc(dev, sizeof(*usbphyc), GFP_KERNEL); if (!usbphyc) @@ -355,11 +348,20 @@ static int stm32_usbphyc_probe(struct platform_device *pdev) goto clk_disable; } + for (i = 0; i < NUM_SUPPLIES; i++) + usbphyc->supplies[i].supply = supplies_names[i]; + + ret = devm_regulator_bulk_get(dev, NUM_SUPPLIES, usbphyc->supplies); + if (ret) { + if (ret != -EPROBE_DEFER) + dev_err(dev, "failed to get regulators: %d\n", ret); + goto clk_disable; + } + for_each_child_of_node(np, child) { struct stm32_usbphyc_phy *usbphyc_phy; struct phy *phy; u32 index; - int i; phy = devm_phy_create(dev, child, &stm32_usbphyc_phy_ops); if (IS_ERR(phy)) { @@ -377,18 +379,6 @@ static int stm32_usbphyc_probe(struct platform_device *pdev) goto put_child; } - for (i = 0; i < NUM_SUPPLIES; i++) - usbphyc_phy->supplies[i].supply = supplies_names[i]; - - ret = devm_regulator_bulk_get(&phy->dev, NUM_SUPPLIES, - usbphyc_phy->supplies); - if (ret) { - if (ret != -EPROBE_DEFER) - dev_err(&phy->dev, - "failed to get regulators: %d\n", ret); - goto put_child; - } - ret = of_property_read_u32(child, "reg", &index); if (ret || index > usbphyc->nphys) { dev_err(&phy->dev, "invalid reg property: %d\n", ret); -- 2.17.1
WARNING: multiple messages have this Message-ID (diff)
From: Amelie Delaunay <amelie.delaunay@foss.st.com> To: Kishon Vijay Abraham I <kishon@ti.com>, Vinod Koul <vkoul@kernel.org>, Rob Herring <robh+dt@kernel.org>, Alexandre Torgue <alexandre.torgue@foss.st.com>, Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Amelie Delaunay <amelie.delaunay@foss.st.com>, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-stm32@st-md-mailman.stormreply.com Subject: [PATCH v2 2/6] phy: stm32: manage 1v1 and 1v8 supplies at pll activation/deactivation Date: Tue, 5 Jan 2021 10:05:21 +0100 [thread overview] Message-ID: <20210105090525.23164-3-amelie.delaunay@foss.st.com> (raw) In-Reply-To: <20210105090525.23164-1-amelie.delaunay@foss.st.com> PLL block requires to be powered with 1v1 and 1v8 supplies to catch ENABLE signal. Currently, supplies are managed through phy_ops .power_on/off, and PLL activation/deactivation is managed through phy_ops .init/exit. The sequence of phy_ops .power_on/.phy_init, .power_off/.exit is USB drivers dependent. To ensure a good behavior of the PLL, supplies have to be managed at PLL activation/deactivation. That means the supplies need to be put in usbphyc node and not in phy children nodes. Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com> --- drivers/phy/st/phy-stm32-usbphyc.c | 102 +++++++++++++---------------- 1 file changed, 46 insertions(+), 56 deletions(-) diff --git a/drivers/phy/st/phy-stm32-usbphyc.c b/drivers/phy/st/phy-stm32-usbphyc.c index a54317e96c41..c78a2c7947ce 100644 --- a/drivers/phy/st/phy-stm32-usbphyc.c +++ b/drivers/phy/st/phy-stm32-usbphyc.c @@ -58,7 +58,6 @@ struct pll_params { struct stm32_usbphyc_phy { struct phy *phy; struct stm32_usbphyc *usbphyc; - struct regulator_bulk_data supplies[NUM_SUPPLIES]; u32 index; bool active; }; @@ -70,6 +69,7 @@ struct stm32_usbphyc { struct reset_control *rst; struct stm32_usbphyc_phy **phys; int nphys; + struct regulator_bulk_data supplies[NUM_SUPPLIES]; int switch_setup; }; @@ -153,10 +153,30 @@ static bool stm32_usbphyc_has_one_phy_active(struct stm32_usbphyc *usbphyc) return false; } +static int stm32_usbphyc_pll_disable(struct stm32_usbphyc *usbphyc) +{ + void __iomem *pll_reg = usbphyc->base + STM32_USBPHYC_PLL; + + /* Check if other phy port active */ + if (stm32_usbphyc_has_one_phy_active(usbphyc)) + return 0; + + stm32_usbphyc_clr_bits(pll_reg, PLLEN); + /* Wait for minimum width of powerdown pulse (ENABLE = Low) */ + udelay(PLL_PWR_DOWN_TIME_US); + + if (readl_relaxed(pll_reg) & PLLEN) { + dev_err(usbphyc->dev, "PLL not reset\n"); + return -EIO; + } + + return regulator_bulk_disable(NUM_SUPPLIES, usbphyc->supplies); +} + static int stm32_usbphyc_pll_enable(struct stm32_usbphyc *usbphyc) { void __iomem *pll_reg = usbphyc->base + STM32_USBPHYC_PLL; - bool pllen = (readl_relaxed(pll_reg) & PLLEN); + bool pllen = readl_relaxed(pll_reg) & PLLEN; int ret; /* Check if one phy port has already configured the pll */ @@ -164,46 +184,35 @@ static int stm32_usbphyc_pll_enable(struct stm32_usbphyc *usbphyc) return 0; if (pllen) { - stm32_usbphyc_clr_bits(pll_reg, PLLEN); - /* Wait for minimum width of powerdown pulse (ENABLE = Low) */ - udelay(PLL_PWR_DOWN_TIME_US); + ret = stm32_usbphyc_pll_disable(usbphyc); + if (ret) + return ret; } - ret = stm32_usbphyc_pll_init(usbphyc); + ret = regulator_bulk_enable(NUM_SUPPLIES, usbphyc->supplies); if (ret) return ret; - stm32_usbphyc_set_bits(pll_reg, PLLEN); + ret = stm32_usbphyc_pll_init(usbphyc); + if (ret) + goto reg_disable; + stm32_usbphyc_set_bits(pll_reg, PLLEN); /* Wait for maximum lock time */ udelay(PLL_LOCK_TIME_US); if (!(readl_relaxed(pll_reg) & PLLEN)) { dev_err(usbphyc->dev, "PLLEN not set\n"); - return -EIO; + ret = -EIO; + goto reg_disable; } return 0; -} - -static int stm32_usbphyc_pll_disable(struct stm32_usbphyc *usbphyc) -{ - void __iomem *pll_reg = usbphyc->base + STM32_USBPHYC_PLL; - - /* Check if other phy port active */ - if (stm32_usbphyc_has_one_phy_active(usbphyc)) - return 0; - stm32_usbphyc_clr_bits(pll_reg, PLLEN); - /* Wait for minimum width of powerdown pulse (ENABLE = Low) */ - udelay(PLL_PWR_DOWN_TIME_US); +reg_disable: + regulator_bulk_disable(NUM_SUPPLIES, usbphyc->supplies); - if (readl_relaxed(pll_reg) & PLLEN) { - dev_err(usbphyc->dev, "PLL not reset\n"); - return -EIO; - } - - return 0; + return ret; } static int stm32_usbphyc_phy_init(struct phy *phy) @@ -231,25 +240,9 @@ static int stm32_usbphyc_phy_exit(struct phy *phy) return stm32_usbphyc_pll_disable(usbphyc); } -static int stm32_usbphyc_phy_power_on(struct phy *phy) -{ - struct stm32_usbphyc_phy *usbphyc_phy = phy_get_drvdata(phy); - - return regulator_bulk_enable(NUM_SUPPLIES, usbphyc_phy->supplies); -} - -static int stm32_usbphyc_phy_power_off(struct phy *phy) -{ - struct stm32_usbphyc_phy *usbphyc_phy = phy_get_drvdata(phy); - - return regulator_bulk_disable(NUM_SUPPLIES, usbphyc_phy->supplies); -} - static const struct phy_ops stm32_usbphyc_phy_ops = { .init = stm32_usbphyc_phy_init, .exit = stm32_usbphyc_phy_exit, - .power_on = stm32_usbphyc_phy_power_on, - .power_off = stm32_usbphyc_phy_power_off, .owner = THIS_MODULE, }; @@ -313,7 +306,7 @@ static int stm32_usbphyc_probe(struct platform_device *pdev) struct device_node *child, *np = dev->of_node; struct phy_provider *phy_provider; u32 version; - int ret, port = 0; + int ret, i, port = 0; usbphyc = devm_kzalloc(dev, sizeof(*usbphyc), GFP_KERNEL); if (!usbphyc) @@ -355,11 +348,20 @@ static int stm32_usbphyc_probe(struct platform_device *pdev) goto clk_disable; } + for (i = 0; i < NUM_SUPPLIES; i++) + usbphyc->supplies[i].supply = supplies_names[i]; + + ret = devm_regulator_bulk_get(dev, NUM_SUPPLIES, usbphyc->supplies); + if (ret) { + if (ret != -EPROBE_DEFER) + dev_err(dev, "failed to get regulators: %d\n", ret); + goto clk_disable; + } + for_each_child_of_node(np, child) { struct stm32_usbphyc_phy *usbphyc_phy; struct phy *phy; u32 index; - int i; phy = devm_phy_create(dev, child, &stm32_usbphyc_phy_ops); if (IS_ERR(phy)) { @@ -377,18 +379,6 @@ static int stm32_usbphyc_probe(struct platform_device *pdev) goto put_child; } - for (i = 0; i < NUM_SUPPLIES; i++) - usbphyc_phy->supplies[i].supply = supplies_names[i]; - - ret = devm_regulator_bulk_get(&phy->dev, NUM_SUPPLIES, - usbphyc_phy->supplies); - if (ret) { - if (ret != -EPROBE_DEFER) - dev_err(&phy->dev, - "failed to get regulators: %d\n", ret); - goto put_child; - } - ret = of_property_read_u32(child, "reg", &index); if (ret || index > usbphyc->nphys) { dev_err(&phy->dev, "invalid reg property: %d\n", ret); -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-01-05 9:06 UTC|newest] Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top 2021-01-05 9:05 [PATCH v2 0/6] STM32 USBPHYC PLL management rework Amelie Delaunay 2021-01-05 9:05 ` Amelie Delaunay 2021-01-05 9:05 ` [PATCH v2 1/6] dt-bindings: phy: phy-stm32-usbphyc: move PLL supplies to parent node Amelie Delaunay 2021-01-05 9:05 ` Amelie Delaunay 2021-01-05 9:05 ` Amelie Delaunay [this message] 2021-01-05 9:05 ` [PATCH v2 2/6] phy: stm32: manage 1v1 and 1v8 supplies at pll activation/deactivation Amelie Delaunay 2021-01-05 9:05 ` [PATCH v2 3/6] phy: stm32: replace regulator_bulk* by multiple regulator_* Amelie Delaunay 2021-01-05 9:05 ` Amelie Delaunay 2021-01-05 9:05 ` [PATCH v2 4/6] phy: stm32: ensure pll is disabled before phys creation Amelie Delaunay 2021-01-05 9:05 ` Amelie Delaunay 2021-01-05 9:05 ` [PATCH v2 5/6] phy: stm32: ensure phy are no more active when removing the driver Amelie Delaunay 2021-01-05 9:05 ` Amelie Delaunay 2021-01-05 9:05 ` [PATCH v2 6/6] phy: stm32: rework PLL Lock detection Amelie Delaunay 2021-01-05 9:05 ` Amelie Delaunay 2021-01-13 15:10 ` [PATCH v2 0/6] STM32 USBPHYC PLL management rework Vinod Koul 2021-01-13 15:10 ` Vinod Koul
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20210105090525.23164-3-amelie.delaunay@foss.st.com \ --to=amelie.delaunay@foss.st.com \ --cc=alexandre.torgue@foss.st.com \ --cc=devicetree@vger.kernel.org \ --cc=kishon@ti.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-stm32@st-md-mailman.stormreply.com \ --cc=mcoquelin.stm32@gmail.com \ --cc=robh+dt@kernel.org \ --cc=vkoul@kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.