* [PATCH v4 0/5] DTS updates for Marvell Armada CN913x platforms @ 2021-02-09 13:46 ` kostap 0 siblings, 0 replies; 18+ messages in thread From: kostap @ 2021-02-09 13:46 UTC (permalink / raw) To: linux-kernel, devicetree, linux-arm-kernel Cc: vladimir.vid, tmn505, luka.kovacic, sebastian.hesselbarth, gregory.clement, andrew, robh+dt, vkoul, kishon, miquel.raynal, mw, jaz, nadavh, stefanc, bpeled, Konstantin Porotchkin From: Konstantin Porotchkin <kostap@marvell.com> This patch series contains the following changes/fixes: 1. Add support for Armada CN913x Development Board topology "B" 2. Add support for Armada CN913x Reference Design boards (CRB) 3. Fixes the CP11X references in PHY binding document 4. Fixes the NAND paritioninig scheme in DTS eliminating gap between consecutive partitions All above changes are already intergated into Marvell official SDK sources v2: - extract common nodes from DB boards to separate DTSI files - disable eth2 on CRB boards until the required phy mode support is added - mention the switch part ID in CRB board description v3: - do not rename setup A DTS files for DB variants - fix a couple of wrong include names v4: - Rebase on top of Linus master branch (v5.11-rc7) - Remove HS400 timing from CRB AP SDHCI (not supported by connected eMMC) - Add cd-gpio entry to CP0 SDHCI for SD card support - Add a comment to CN9130-CRB patch about the required defconfig changes for supporting the onboard i2c expander - Add Stefan's patch to enable 10G port on CN9130-DB platforms Grzegorz Jaszczyk (1): Documentation/bindings: phy: update references to cp11x Konstantin Porotchkin (3): arch/arm64/boot/dts/marvell: fix NAND partitioning scheme arm64: dts: cn913x: add device trees for topology B boards arm64: dts: add support for Marvell cn9130-crb platform Stefan Chulski (1): dts: marvell: Enable 10G interface on 9130-DB board .../bindings/phy/phy-mvebu-comphy.txt | 12 +- arch/arm64/boot/dts/marvell/Makefile | 5 + arch/arm64/boot/dts/marvell/cn9130-crb-A.dts | 38 ++ arch/arm64/boot/dts/marvell/cn9130-crb-B.dts | 46 ++ arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 221 ++++++++++ arch/arm64/boot/dts/marvell/cn9130-db-B.dts | 22 + arch/arm64/boot/dts/marvell/cn9130-db.dts | 393 +---------------- arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 402 ++++++++++++++++++ arch/arm64/boot/dts/marvell/cn9131-db-B.dts | 22 + arch/arm64/boot/dts/marvell/cn9131-db.dts | 192 +-------- arch/arm64/boot/dts/marvell/cn9131-db.dtsi | 201 +++++++++ arch/arm64/boot/dts/marvell/cn9132-db-B.dts | 22 + arch/arm64/boot/dts/marvell/cn9132-db.dts | 211 +-------- arch/arm64/boot/dts/marvell/cn9132-db.dtsi | 220 ++++++++++ 14 files changed, 1223 insertions(+), 784 deletions(-) create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dtsi -- 2.17.1 ^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v4 0/5] DTS updates for Marvell Armada CN913x platforms @ 2021-02-09 13:46 ` kostap 0 siblings, 0 replies; 18+ messages in thread From: kostap @ 2021-02-09 13:46 UTC (permalink / raw) To: linux-kernel, devicetree, linux-arm-kernel Cc: tmn505, andrew, nadavh, jaz, gregory.clement, vkoul, kishon, vladimir.vid, luka.kovacic, robh+dt, miquel.raynal, Konstantin Porotchkin, stefanc, mw, bpeled, sebastian.hesselbarth From: Konstantin Porotchkin <kostap@marvell.com> This patch series contains the following changes/fixes: 1. Add support for Armada CN913x Development Board topology "B" 2. Add support for Armada CN913x Reference Design boards (CRB) 3. Fixes the CP11X references in PHY binding document 4. Fixes the NAND paritioninig scheme in DTS eliminating gap between consecutive partitions All above changes are already intergated into Marvell official SDK sources v2: - extract common nodes from DB boards to separate DTSI files - disable eth2 on CRB boards until the required phy mode support is added - mention the switch part ID in CRB board description v3: - do not rename setup A DTS files for DB variants - fix a couple of wrong include names v4: - Rebase on top of Linus master branch (v5.11-rc7) - Remove HS400 timing from CRB AP SDHCI (not supported by connected eMMC) - Add cd-gpio entry to CP0 SDHCI for SD card support - Add a comment to CN9130-CRB patch about the required defconfig changes for supporting the onboard i2c expander - Add Stefan's patch to enable 10G port on CN9130-DB platforms Grzegorz Jaszczyk (1): Documentation/bindings: phy: update references to cp11x Konstantin Porotchkin (3): arch/arm64/boot/dts/marvell: fix NAND partitioning scheme arm64: dts: cn913x: add device trees for topology B boards arm64: dts: add support for Marvell cn9130-crb platform Stefan Chulski (1): dts: marvell: Enable 10G interface on 9130-DB board .../bindings/phy/phy-mvebu-comphy.txt | 12 +- arch/arm64/boot/dts/marvell/Makefile | 5 + arch/arm64/boot/dts/marvell/cn9130-crb-A.dts | 38 ++ arch/arm64/boot/dts/marvell/cn9130-crb-B.dts | 46 ++ arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 221 ++++++++++ arch/arm64/boot/dts/marvell/cn9130-db-B.dts | 22 + arch/arm64/boot/dts/marvell/cn9130-db.dts | 393 +---------------- arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 402 ++++++++++++++++++ arch/arm64/boot/dts/marvell/cn9131-db-B.dts | 22 + arch/arm64/boot/dts/marvell/cn9131-db.dts | 192 +-------- arch/arm64/boot/dts/marvell/cn9131-db.dtsi | 201 +++++++++ arch/arm64/boot/dts/marvell/cn9132-db-B.dts | 22 + arch/arm64/boot/dts/marvell/cn9132-db.dts | 211 +-------- arch/arm64/boot/dts/marvell/cn9132-db.dtsi | 220 ++++++++++ 14 files changed, 1223 insertions(+), 784 deletions(-) create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dtsi -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v4 1/5] Documentation/bindings: phy: update references to cp11x 2021-02-09 13:46 ` kostap @ 2021-02-09 13:46 ` kostap -1 siblings, 0 replies; 18+ messages in thread From: kostap @ 2021-02-09 13:46 UTC (permalink / raw) To: linux-kernel, devicetree, linux-arm-kernel Cc: vladimir.vid, tmn505, luka.kovacic, sebastian.hesselbarth, gregory.clement, andrew, robh+dt, vkoul, kishon, miquel.raynal, mw, jaz, nadavh, stefanc, bpeled, Konstantin Porotchkin From: Grzegorz Jaszczyk <jaz@semihalf.com> The cp11x references in dts has changed, reflect it in comphy documentation. Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com> Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> --- Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt b/Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt index 8c60e6985950..5ffd0f55d010 100644 --- a/Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt +++ b/Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt @@ -42,22 +42,22 @@ Required properties (child nodes): Examples: - cpm_comphy: phy@120000 { + CP11X_LABEL(comphy): phy@120000 { compatible = "marvell,comphy-cp110"; reg = <0x120000 0x6000>; - marvell,system-controller = <&cpm_syscon0>; - clocks = <&CP110_LABEL(clk) 1 5>, <&CP110_LABEL(clk) 1 6>, - <&CP110_LABEL(clk) 1 18>; + marvell,system-controller = <&CP11X_LABEL(syscon0)>; + clocks = <&CP11X_LABEL(clk) 1 5>, <&CP11X_LABEL(clk) 1 6>, + <&CP11X_LABEL(clk) 1 18>; clock-names = "mg_clk", "mg_core_clk", "axi_clk"; #address-cells = <1>; #size-cells = <0>; - cpm_comphy0: phy@0 { + CP11X_LABEL(comphy0): phy@0 { reg = <0>; #phy-cells = <1>; }; - cpm_comphy1: phy@1 { + CP11X_LABEL(comphy1): phy@1 { reg = <1>; #phy-cells = <1>; }; -- 2.17.1 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v4 1/5] Documentation/bindings: phy: update references to cp11x @ 2021-02-09 13:46 ` kostap 0 siblings, 0 replies; 18+ messages in thread From: kostap @ 2021-02-09 13:46 UTC (permalink / raw) To: linux-kernel, devicetree, linux-arm-kernel Cc: tmn505, andrew, nadavh, jaz, gregory.clement, vkoul, kishon, vladimir.vid, luka.kovacic, robh+dt, miquel.raynal, Konstantin Porotchkin, stefanc, mw, bpeled, sebastian.hesselbarth From: Grzegorz Jaszczyk <jaz@semihalf.com> The cp11x references in dts has changed, reflect it in comphy documentation. Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com> Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> --- Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt b/Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt index 8c60e6985950..5ffd0f55d010 100644 --- a/Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt +++ b/Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt @@ -42,22 +42,22 @@ Required properties (child nodes): Examples: - cpm_comphy: phy@120000 { + CP11X_LABEL(comphy): phy@120000 { compatible = "marvell,comphy-cp110"; reg = <0x120000 0x6000>; - marvell,system-controller = <&cpm_syscon0>; - clocks = <&CP110_LABEL(clk) 1 5>, <&CP110_LABEL(clk) 1 6>, - <&CP110_LABEL(clk) 1 18>; + marvell,system-controller = <&CP11X_LABEL(syscon0)>; + clocks = <&CP11X_LABEL(clk) 1 5>, <&CP11X_LABEL(clk) 1 6>, + <&CP11X_LABEL(clk) 1 18>; clock-names = "mg_clk", "mg_core_clk", "axi_clk"; #address-cells = <1>; #size-cells = <0>; - cpm_comphy0: phy@0 { + CP11X_LABEL(comphy0): phy@0 { reg = <0>; #phy-cells = <1>; }; - cpm_comphy1: phy@1 { + CP11X_LABEL(comphy1): phy@1 { reg = <1>; #phy-cells = <1>; }; -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v4 2/5] arch/arm64/boot/dts/marvell: fix NAND partitioning scheme 2021-02-09 13:46 ` kostap @ 2021-02-09 13:46 ` kostap -1 siblings, 0 replies; 18+ messages in thread From: kostap @ 2021-02-09 13:46 UTC (permalink / raw) To: linux-kernel, devicetree, linux-arm-kernel Cc: vladimir.vid, tmn505, luka.kovacic, sebastian.hesselbarth, gregory.clement, andrew, robh+dt, vkoul, kishon, miquel.raynal, mw, jaz, nadavh, stefanc, bpeled, Konstantin Porotchkin From: Konstantin Porotchkin <kostap@marvell.com> Eliminate 1MB gap between Linux and filesystem partitions. Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> --- arch/arm64/boot/dts/marvell/cn9130-db.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/marvell/cn9130-db.dts b/arch/arm64/boot/dts/marvell/cn9130-db.dts index ce49a70d88a0..d24294888400 100644 --- a/arch/arm64/boot/dts/marvell/cn9130-db.dts +++ b/arch/arm64/boot/dts/marvell/cn9130-db.dts @@ -258,7 +258,7 @@ }; partition@200000 { label = "Linux"; - reg = <0x200000 0xd00000>; + reg = <0x200000 0xe00000>; }; partition@1000000 { label = "Filesystem"; -- 2.17.1 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v4 2/5] arch/arm64/boot/dts/marvell: fix NAND partitioning scheme @ 2021-02-09 13:46 ` kostap 0 siblings, 0 replies; 18+ messages in thread From: kostap @ 2021-02-09 13:46 UTC (permalink / raw) To: linux-kernel, devicetree, linux-arm-kernel Cc: tmn505, andrew, nadavh, jaz, gregory.clement, vkoul, kishon, vladimir.vid, luka.kovacic, robh+dt, miquel.raynal, Konstantin Porotchkin, stefanc, mw, bpeled, sebastian.hesselbarth From: Konstantin Porotchkin <kostap@marvell.com> Eliminate 1MB gap between Linux and filesystem partitions. Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> --- arch/arm64/boot/dts/marvell/cn9130-db.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/marvell/cn9130-db.dts b/arch/arm64/boot/dts/marvell/cn9130-db.dts index ce49a70d88a0..d24294888400 100644 --- a/arch/arm64/boot/dts/marvell/cn9130-db.dts +++ b/arch/arm64/boot/dts/marvell/cn9130-db.dts @@ -258,7 +258,7 @@ }; partition@200000 { label = "Linux"; - reg = <0x200000 0xd00000>; + reg = <0x200000 0xe00000>; }; partition@1000000 { label = "Filesystem"; -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v4 3/5] arm64: dts: cn913x: add device trees for topology B boards 2021-02-09 13:46 ` kostap @ 2021-02-09 13:46 ` kostap -1 siblings, 0 replies; 18+ messages in thread From: kostap @ 2021-02-09 13:46 UTC (permalink / raw) To: linux-kernel, devicetree, linux-arm-kernel Cc: vladimir.vid, tmn505, luka.kovacic, sebastian.hesselbarth, gregory.clement, andrew, robh+dt, vkoul, kishon, miquel.raynal, mw, jaz, nadavh, stefanc, bpeled, Konstantin Porotchkin From: Konstantin Porotchkin <kostap@marvell.com> The CN913x DB with topology B is similar to a regular setup (A) boards, but uses NAND flash as a boot device, while topology A boards are booting from SPI flash. Since NAND and SPI on CN913x DB boards share some wires, they cannot be activated simultaneously. The DTS files for setup "B" are based on setup "A", in which the CP0 NAND controller enabled and CP0 SPI1 disabled. Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> --- arch/arm64/boot/dts/marvell/Makefile | 3 + arch/arm64/boot/dts/marvell/cn9130-db-B.dts | 22 ++ arch/arm64/boot/dts/marvell/cn9130-db.dts | 393 +------------------ arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 402 ++++++++++++++++++++ arch/arm64/boot/dts/marvell/cn9131-db-B.dts | 22 ++ arch/arm64/boot/dts/marvell/cn9131-db.dts | 192 +--------- arch/arm64/boot/dts/marvell/cn9131-db.dtsi | 201 ++++++++++ arch/arm64/boot/dts/marvell/cn9132-db-B.dts | 22 ++ arch/arm64/boot/dts/marvell/cn9132-db.dts | 211 +--------- arch/arm64/boot/dts/marvell/cn9132-db.dtsi | 220 +++++++++++ 10 files changed, 910 insertions(+), 778 deletions(-) create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dtsi diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile index 34efe0fb6f37..5e39f9774e68 100644 --- a/arch/arm64/boot/dts/marvell/Makefile +++ b/arch/arm64/boot/dts/marvell/Makefile @@ -16,5 +16,8 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin-singleshot.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-puzzle-m801.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-8080-db.dtb dtb-$(CONFIG_ARCH_MVEBU) += cn9130-db.dtb +dtb-$(CONFIG_ARCH_MVEBU) += cn9130-db-B.dtb dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db.dtb +dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db-B.dtb dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db.dtb +dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db-B.dtb diff --git a/arch/arm64/boot/dts/marvell/cn9130-db-B.dts b/arch/arm64/boot/dts/marvell/cn9130-db-B.dts new file mode 100644 index 000000000000..57e41cacd483 --- /dev/null +++ b/arch/arm64/boot/dts/marvell/cn9130-db-B.dts @@ -0,0 +1,22 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2020 Marvell International Ltd. + * + * Device tree for the CN9130-DB board (setup "B"). + */ + +#include "cn9130-db.dtsi" + +/ { + model = "Marvell Armada CN9130-DB setup B"; +}; + +/* Setup B has NAND flash as a boot device, while regular setup uses SPI flash. + * Since CP0 SPI1 and CP0 NAND are sharing some pins, they cannot be activated + * simultaneously. When NAND controller is enabled, SPI1 should be disabled. + */ + +&cp0_nand_controller { + status = "okay"; +}; + diff --git a/arch/arm64/boot/dts/marvell/cn9130-db.dts b/arch/arm64/boot/dts/marvell/cn9130-db.dts index d24294888400..994f347f2973 100644 --- a/arch/arm64/boot/dts/marvell/cn9130-db.dts +++ b/arch/arm64/boot/dts/marvell/cn9130-db.dts @@ -5,399 +5,18 @@ * Device tree for the CN9130-DB board. */ -#include "cn9130.dtsi" - -#include <dt-bindings/gpio/gpio.h> +#include "cn9130-db.dtsi" / { - model = "Marvell Armada CN9130-DB"; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - aliases { - gpio1 = &cp0_gpio1; - gpio2 = &cp0_gpio2; - i2c0 = &cp0_i2c0; - ethernet0 = &cp0_eth0; - ethernet1 = &cp0_eth1; - ethernet2 = &cp0_eth2; - spi1 = &cp0_spi0; - spi2 = &cp0_spi1; - }; - - memory@00000000 { - device_type = "memory"; - reg = <0x0 0x0 0x0 0x80000000>; - }; - - ap0_reg_sd_vccq: ap0_sd_vccq@0 { - compatible = "regulator-gpio"; - regulator-name = "ap0_sd_vccq"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - gpios = <&expander0 8 GPIO_ACTIVE_HIGH>; - states = <1800000 0x1 3300000 0x0>; - }; - - cp0_reg_usb3_vbus0: cp0_usb3_vbus@0 { - compatible = "regulator-fixed"; - regulator-name = "cp0-xhci0-vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - gpio = <&expander0 0 GPIO_ACTIVE_HIGH>; - }; - - cp0_usb3_0_phy0: cp0_usb3_phy@0 { - compatible = "usb-nop-xceiv"; - vcc-supply = <&cp0_reg_usb3_vbus0>; - }; - - cp0_reg_usb3_vbus1: cp0_usb3_vbus@1 { - compatible = "regulator-fixed"; - regulator-name = "cp0-xhci1-vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - gpio = <&expander0 1 GPIO_ACTIVE_HIGH>; - }; - - cp0_usb3_0_phy1: cp0_usb3_phy@1 { - compatible = "usb-nop-xceiv"; - vcc-supply = <&cp0_reg_usb3_vbus1>; - }; - - cp0_reg_sd_vccq: cp0_sd_vccq@0 { - compatible = "regulator-gpio"; - regulator-name = "cp0_sd_vccq"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - gpios = <&expander0 15 GPIO_ACTIVE_HIGH>; - states = <1800000 0x1 - 3300000 0x0>; - }; - - cp0_reg_sd_vcc: cp0_sd_vcc@0 { - compatible = "regulator-fixed"; - regulator-name = "cp0_sd_vcc"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&expander0 14 GPIO_ACTIVE_HIGH>; - enable-active-high; - regulator-always-on; - }; - - cp0_sfp_eth0: sfp-eth@0 { - compatible = "sff,sfp"; - i2c-bus = <&cp0_sfpp0_i2c>; - los-gpio = <&cp0_module_expander1 11 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&cp0_module_expander1 10 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&cp0_module_expander1 9 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&cp0_module_expander1 8 GPIO_ACTIVE_HIGH>; - /* - * SFP cages are unconnected on early PCBs because of an the I2C - * lanes not being connected. Prevent the port for being - * unusable by disabling the SFP node. - */ - status = "disabled"; - }; -}; - -&uart0 { - status = "okay"; -}; - -/* on-board eMMC - U9 */ -&ap_sdhci0 { - pinctrl-names = "default"; - bus-width = <8>; - vqmmc-supply = <&ap0_reg_sd_vccq>; - status = "okay"; + model = "Marvell Armada CN9130-DB setup A"; }; -&cp0_crypto { - status = "disabled"; -}; - -&cp0_ethernet { - status = "okay"; -}; - -/* SLM-1521-V2, CON9 */ -&cp0_eth0 { - status = "disabled"; - phy-mode = "10gbase-kr"; - /* Generic PHY, providing serdes lanes */ - phys = <&cp0_comphy4 0>; - managed = "in-band-status"; - sfp = <&cp0_sfp_eth0>; -}; - -/* CON56 */ -&cp0_eth1 { - status = "okay"; - phy = <&phy0>; - phy-mode = "rgmii-id"; -}; - -/* CON57 */ -&cp0_eth2 { - status = "okay"; - phy = <&phy1>; - phy-mode = "rgmii-id"; -}; - -&cp0_gpio1 { - status = "okay"; -}; - -&cp0_gpio2 { - status = "okay"; -}; - -&cp0_i2c0 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&cp0_i2c0_pins>; - clock-frequency = <100000>; - - /* U36 */ - expander0: pca953x@21 { - compatible = "nxp,pca9555"; - pinctrl-names = "default"; - gpio-controller; - #gpio-cells = <2>; - reg = <0x21>; - status = "okay"; - }; - - /* U42 */ - eeprom0: eeprom@50 { - compatible = "atmel,24c64"; - reg = <0x50>; - pagesize = <0x20>; - }; - - /* U38 */ - eeprom1: eeprom@57 { - compatible = "atmel,24c64"; - reg = <0x57>; - pagesize = <0x20>; - }; -}; - -&cp0_i2c1 { - status = "okay"; - clock-frequency = <100000>; - - /* SLM-1521-V2 - U3 */ - i2c-mux@72 { /* verify address - depends on dpr */ - compatible = "nxp,pca9544"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x72>; - cp0_sfpp0_i2c: i2c@0 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - }; - - i2c@1 { - #address-cells = <1>; - #size-cells = <0>; - reg = <1>; - /* U12 */ - cp0_module_expander1: pca9555@21 { - compatible = "nxp,pca9555"; - pinctrl-names = "default"; - gpio-controller; - #gpio-cells = <2>; - reg = <0x21>; - }; - - }; - }; -}; - -&cp0_mdio { - status = "okay"; - - phy0: ethernet-phy@0 { - reg = <0>; - }; - - phy1: ethernet-phy@1 { - reg = <1>; - }; -}; - -/* U54 */ -&cp0_nand_controller { - pinctrl-names = "default"; - pinctrl-0 = <&nand_pins &nand_rb>; - - nand@0 { - reg = <0>; - label = "main-storage"; - nand-rb = <0>; - nand-ecc-mode = "hw"; - nand-on-flash-bbt; - nand-ecc-strength = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "U-Boot"; - reg = <0 0x200000>; - }; - partition@200000 { - label = "Linux"; - reg = <0x200000 0xe00000>; - }; - partition@1000000 { - label = "Filesystem"; - reg = <0x1000000 0x3f000000>; - }; - }; - }; -}; - -/* SLM-1521-V2, CON6 */ -&cp0_pcie0 { - status = "okay"; - num-lanes = <4>; - num-viewport = <8>; - /* Generic PHY, providing serdes lanes */ - phys = <&cp0_comphy0 0 - &cp0_comphy1 0 - &cp0_comphy2 0 - &cp0_comphy3 0>; -}; - -&cp0_sata0 { - status = "okay"; - - /* SLM-1521-V2, CON2 */ - sata-port@1 { - status = "okay"; - /* Generic PHY, providing serdes lanes */ - phys = <&cp0_comphy5 1>; - }; -}; - -/* CON 28 */ -&cp0_sdhci0 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&cp0_sdhci_pins - &cp0_sdhci_cd_pins>; - bus-width = <4>; - cd-gpios = <&cp0_gpio2 11 GPIO_ACTIVE_LOW>; - no-1-8-v; - vqmmc-supply = <&cp0_reg_sd_vccq>; - vmmc-supply = <&cp0_reg_sd_vcc>; -}; +/* Setup A has SPI1 flash as a boot device, while setup B uses NAND flash. + * Since CP0 SPI1 and CP0 NAND are sharing some pins, they cannot be activated + * simultaneously. When SPI controller is enabled, NAND should be disabled. + */ -/* U55 */ &cp0_spi1 { status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&cp0_spi0_pins>; - reg = <0x700680 0x50>; - - spi-flash@0 { - #address-cells = <0x1>; - #size-cells = <0x1>; - compatible = "jedec,spi-nor"; - reg = <0x0>; - /* On-board MUX does not allow higher frequencies */ - spi-max-frequency = <40000000>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "U-Boot-0"; - reg = <0x0 0x200000>; - }; - - partition@400000 { - label = "Filesystem-0"; - reg = <0x200000 0xe00000>; - }; - }; - }; -}; - -&cp0_syscon0 { - cp0_pinctrl: pinctrl { - compatible = "marvell,cp115-standalone-pinctrl"; - - cp0_i2c0_pins: cp0-i2c-pins-0 { - marvell,pins = "mpp37", "mpp38"; - marvell,function = "i2c0"; - }; - cp0_i2c1_pins: cp0-i2c-pins-1 { - marvell,pins = "mpp35", "mpp36"; - marvell,function = "i2c1"; - }; - cp0_ge1_rgmii_pins: cp0-ge-rgmii-pins-0 { - marvell,pins = "mpp0", "mpp1", "mpp2", - "mpp3", "mpp4", "mpp5", - "mpp6", "mpp7", "mpp8", - "mpp9", "mpp10", "mpp11"; - marvell,function = "ge0"; - }; - cp0_ge2_rgmii_pins: cp0-ge-rgmii-pins-1 { - marvell,pins = "mpp44", "mpp45", "mpp46", - "mpp47", "mpp48", "mpp49", - "mpp50", "mpp51", "mpp52", - "mpp53", "mpp54", "mpp55"; - marvell,function = "ge1"; - }; - cp0_sdhci_cd_pins: cp0-sdhci-cd-pins-0 { - marvell,pins = "mpp43"; - marvell,function = "gpio"; - }; - cp0_sdhci_pins: cp0-sdhi-pins-0 { - marvell,pins = "mpp56", "mpp57", "mpp58", - "mpp59", "mpp60", "mpp61"; - marvell,function = "sdio"; - }; - cp0_spi0_pins: cp0-spi-pins-0 { - marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16"; - marvell,function = "spi1"; - }; - nand_pins: nand-pins { - marvell,pins = "mpp15", "mpp16", "mpp17", "mpp18", - "mpp19", "mpp20", "mpp21", "mpp22", - "mpp23", "mpp24", "mpp25", "mpp26", - "mpp27"; - marvell,function = "dev"; - }; - nand_rb: nand-rb { - marvell,pins = "mpp13"; - marvell,function = "nf"; - }; - }; -}; - -&cp0_usb3_0 { - status = "okay"; - usb-phy = <&cp0_usb3_0_phy0>; - phy-names = "usb"; }; -&cp0_usb3_1 { - status = "okay"; - usb-phy = <&cp0_usb3_0_phy1>; - phy-names = "usb"; -}; diff --git a/arch/arm64/boot/dts/marvell/cn9130-db.dtsi b/arch/arm64/boot/dts/marvell/cn9130-db.dtsi new file mode 100644 index 000000000000..8de3a552b806 --- /dev/null +++ b/arch/arm64/boot/dts/marvell/cn9130-db.dtsi @@ -0,0 +1,402 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2019 Marvell International Ltd. + * + * Device tree for the CN9130-DB board. + */ + +#include "cn9130.dtsi" + +#include <dt-bindings/gpio/gpio.h> + +/ { + chosen { + stdout-path = "serial0:115200n8"; + }; + + aliases { + gpio1 = &cp0_gpio1; + gpio2 = &cp0_gpio2; + i2c0 = &cp0_i2c0; + ethernet0 = &cp0_eth0; + ethernet1 = &cp0_eth1; + ethernet2 = &cp0_eth2; + spi1 = &cp0_spi0; + spi2 = &cp0_spi1; + }; + + memory@00000000 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + ap0_reg_sd_vccq: ap0_sd_vccq@0 { + compatible = "regulator-gpio"; + regulator-name = "ap0_sd_vccq"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + gpios = <&expander0 8 GPIO_ACTIVE_HIGH>; + states = <1800000 0x1 3300000 0x0>; + }; + + cp0_reg_usb3_vbus0: cp0_usb3_vbus@0 { + compatible = "regulator-fixed"; + regulator-name = "cp0-xhci0-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&expander0 0 GPIO_ACTIVE_HIGH>; + }; + + cp0_usb3_0_phy0: cp0_usb3_phy@0 { + compatible = "usb-nop-xceiv"; + vcc-supply = <&cp0_reg_usb3_vbus0>; + }; + + cp0_reg_usb3_vbus1: cp0_usb3_vbus@1 { + compatible = "regulator-fixed"; + regulator-name = "cp0-xhci1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&expander0 1 GPIO_ACTIVE_HIGH>; + }; + + cp0_usb3_0_phy1: cp0_usb3_phy@1 { + compatible = "usb-nop-xceiv"; + vcc-supply = <&cp0_reg_usb3_vbus1>; + }; + + cp0_reg_sd_vccq: cp0_sd_vccq@0 { + compatible = "regulator-gpio"; + regulator-name = "cp0_sd_vccq"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + gpios = <&expander0 15 GPIO_ACTIVE_HIGH>; + states = <1800000 0x1 + 3300000 0x0>; + }; + + cp0_reg_sd_vcc: cp0_sd_vcc@0 { + compatible = "regulator-fixed"; + regulator-name = "cp0_sd_vcc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&expander0 14 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + cp0_sfp_eth0: sfp-eth@0 { + compatible = "sff,sfp"; + i2c-bus = <&cp0_sfpp0_i2c>; + los-gpio = <&cp0_module_expander1 11 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&cp0_module_expander1 10 GPIO_ACTIVE_LOW>; + tx-disable-gpio = <&cp0_module_expander1 9 GPIO_ACTIVE_HIGH>; + tx-fault-gpio = <&cp0_module_expander1 8 GPIO_ACTIVE_HIGH>; + /* + * SFP cages are unconnected on early PCBs because of an the I2C + * lanes not being connected. Prevent the port for being + * unusable by disabling the SFP node. + */ + status = "disabled"; + }; +}; + +&uart0 { + status = "okay"; +}; + +/* on-board eMMC - U9 */ +&ap_sdhci0 { + pinctrl-names = "default"; + bus-width = <8>; + vqmmc-supply = <&ap0_reg_sd_vccq>; + status = "okay"; +}; + +&cp0_crypto { + status = "disabled"; +}; + +&cp0_ethernet { + status = "okay"; +}; + +/* SLM-1521-V2, CON9 */ +&cp0_eth0 { + status = "disabled"; + phy-mode = "10gbase-kr"; + /* Generic PHY, providing serdes lanes */ + phys = <&cp0_comphy4 0>; + managed = "in-band-status"; + sfp = <&cp0_sfp_eth0>; +}; + +/* CON56 */ +&cp0_eth1 { + status = "okay"; + phy = <&phy0>; + phy-mode = "rgmii-id"; +}; + +/* CON57 */ +&cp0_eth2 { + status = "okay"; + phy = <&phy1>; + phy-mode = "rgmii-id"; +}; + +&cp0_gpio1 { + status = "okay"; +}; + +&cp0_gpio2 { + status = "okay"; +}; + +&cp0_i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_i2c0_pins>; + clock-frequency = <100000>; + + /* U36 */ + expander0: pca953x@21 { + compatible = "nxp,pca9555"; + pinctrl-names = "default"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x21>; + status = "okay"; + }; + + /* U42 */ + eeprom0: eeprom@50 { + compatible = "atmel,24c64"; + reg = <0x50>; + pagesize = <0x20>; + }; + + /* U38 */ + eeprom1: eeprom@57 { + compatible = "atmel,24c64"; + reg = <0x57>; + pagesize = <0x20>; + }; +}; + +&cp0_i2c1 { + status = "okay"; + clock-frequency = <100000>; + + /* SLM-1521-V2 - U3 */ + i2c-mux@72 { /* verify address - depends on dpr */ + compatible = "nxp,pca9544"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x72>; + cp0_sfpp0_i2c: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + /* U12 */ + cp0_module_expander1: pca9555@21 { + compatible = "nxp,pca9555"; + pinctrl-names = "default"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x21>; + }; + + }; + }; +}; + +&cp0_mdio { + status = "okay"; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; +}; + +/* U54 */ +&cp0_nand_controller { + status = "disabled"; + pinctrl-names = "default"; + pinctrl-0 = <&nand_pins &nand_rb>; + + nand@0 { + reg = <0>; + label = "main-storage"; + nand-rb = <0>; + nand-ecc-mode = "hw"; + nand-on-flash-bbt; + nand-ecc-strength = <8>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "U-Boot"; + reg = <0 0x200000>; + }; + partition@200000 { + label = "Linux"; + reg = <0x200000 0xe00000>; + }; + partition@1000000 { + label = "Filesystem"; + reg = <0x1000000 0x3f000000>; + }; + }; + }; +}; + +/* SLM-1521-V2, CON6 */ +&cp0_pcie0 { + status = "okay"; + num-lanes = <4>; + num-viewport = <8>; + /* Generic PHY, providing serdes lanes */ + phys = <&cp0_comphy0 0 + &cp0_comphy1 0 + &cp0_comphy2 0 + &cp0_comphy3 0>; +}; + +&cp0_sata0 { + status = "okay"; + + /* SLM-1521-V2, CON2 */ + sata-port@1 { + status = "okay"; + /* Generic PHY, providing serdes lanes */ + phys = <&cp0_comphy5 1>; + }; +}; + +/* CON 28 */ +&cp0_sdhci0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_sdhci_pins + &cp0_sdhci_cd_pins>; + bus-width = <4>; + cd-gpios = <&cp0_gpio2 11 GPIO_ACTIVE_LOW>; + no-1-8-v; + vqmmc-supply = <&cp0_reg_sd_vccq>; + vmmc-supply = <&cp0_reg_sd_vcc>; +}; + +/* U55 */ +&cp0_spi1 { + status = "disabled"; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_spi0_pins>; + reg = <0x700680 0x50>; + + spi-flash@0 { + #address-cells = <0x1>; + #size-cells = <0x1>; + compatible = "jedec,spi-nor"; + reg = <0x0>; + /* On-board MUX does not allow higher frequencies */ + spi-max-frequency = <40000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "U-Boot-0"; + reg = <0x0 0x200000>; + }; + + partition@400000 { + label = "Filesystem-0"; + reg = <0x200000 0xe00000>; + }; + }; + }; +}; + +&cp0_syscon0 { + cp0_pinctrl: pinctrl { + compatible = "marvell,cp115-standalone-pinctrl"; + + cp0_i2c0_pins: cp0-i2c-pins-0 { + marvell,pins = "mpp37", "mpp38"; + marvell,function = "i2c0"; + }; + cp0_i2c1_pins: cp0-i2c-pins-1 { + marvell,pins = "mpp35", "mpp36"; + marvell,function = "i2c1"; + }; + cp0_ge1_rgmii_pins: cp0-ge-rgmii-pins-0 { + marvell,pins = "mpp0", "mpp1", "mpp2", + "mpp3", "mpp4", "mpp5", + "mpp6", "mpp7", "mpp8", + "mpp9", "mpp10", "mpp11"; + marvell,function = "ge0"; + }; + cp0_ge2_rgmii_pins: cp0-ge-rgmii-pins-1 { + marvell,pins = "mpp44", "mpp45", "mpp46", + "mpp47", "mpp48", "mpp49", + "mpp50", "mpp51", "mpp52", + "mpp53", "mpp54", "mpp55"; + marvell,function = "ge1"; + }; + cp0_sdhci_cd_pins: cp0-sdhci-cd-pins-0 { + marvell,pins = "mpp43"; + marvell,function = "gpio"; + }; + cp0_sdhci_pins: cp0-sdhi-pins-0 { + marvell,pins = "mpp56", "mpp57", "mpp58", + "mpp59", "mpp60", "mpp61"; + marvell,function = "sdio"; + }; + cp0_spi0_pins: cp0-spi-pins-0 { + marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16"; + marvell,function = "spi1"; + }; + nand_pins: nand-pins { + marvell,pins = "mpp15", "mpp16", "mpp17", "mpp18", + "mpp19", "mpp20", "mpp21", "mpp22", + "mpp23", "mpp24", "mpp25", "mpp26", + "mpp27"; + marvell,function = "dev"; + }; + nand_rb: nand-rb { + marvell,pins = "mpp13"; + marvell,function = "nf"; + }; + }; +}; + +&cp0_usb3_0 { + status = "okay"; + usb-phy = <&cp0_usb3_0_phy0>; + phy-names = "usb"; +}; + +&cp0_usb3_1 { + status = "okay"; + usb-phy = <&cp0_usb3_0_phy1>; + phy-names = "usb"; +}; diff --git a/arch/arm64/boot/dts/marvell/cn9131-db-B.dts b/arch/arm64/boot/dts/marvell/cn9131-db-B.dts new file mode 100644 index 000000000000..183b1ec8b1f0 --- /dev/null +++ b/arch/arm64/boot/dts/marvell/cn9131-db-B.dts @@ -0,0 +1,22 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2020 Marvell International Ltd. + * + * Device tree for the CN9131-DB board (setup "B"). + */ + +#include "cn9131-db.dtsi" + +/ { + model = "Marvell Armada CN9131-DB setup B"; +}; + +/* Setup B has NAND flash as a boot device, while regular setup uses SPI flash. + * Since CP0 SPI1 and CP0 NAND are sharing some pins, they cannot be activated + * simultaneously. When NAND controller is enabled, SPI1 should be disabled. + */ + +&cp0_nand_controller { + status = "okay"; +}; + diff --git a/arch/arm64/boot/dts/marvell/cn9131-db.dts b/arch/arm64/boot/dts/marvell/cn9131-db.dts index 3c975f98b2a3..a60fdee79bf8 100644 --- a/arch/arm64/boot/dts/marvell/cn9131-db.dts +++ b/arch/arm64/boot/dts/marvell/cn9131-db.dts @@ -5,198 +5,18 @@ * Device tree for the CN9131-DB board. */ -#include "cn9130-db.dts" +#include "cn9131-db.dtsi" / { - model = "Marvell Armada CN9131-DB"; - compatible = "marvell,cn9131", "marvell,cn9130", - "marvell,armada-ap807-quad", "marvell,armada-ap807"; - - aliases { - gpio3 = &cp1_gpio1; - gpio4 = &cp1_gpio2; - ethernet3 = &cp1_eth0; - ethernet4 = &cp1_eth1; - }; - - cp1_reg_usb3_vbus0: cp1_usb3_vbus@0 { - compatible = "regulator-fixed"; - pinctrl-names = "default"; - pinctrl-0 = <&cp1_xhci0_vbus_pins>; - regulator-name = "cp1-xhci0-vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - gpio = <&cp1_gpio1 3 GPIO_ACTIVE_HIGH>; - }; - - cp1_usb3_0_phy0: cp1_usb3_phy0 { - compatible = "usb-nop-xceiv"; - vcc-supply = <&cp1_reg_usb3_vbus0>; - }; - - cp1_sfp_eth1: sfp-eth1 { - compatible = "sff,sfp"; - i2c-bus = <&cp1_i2c0>; - los-gpio = <&cp1_gpio1 11 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&cp1_gpio1 10 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&cp1_gpio1 9 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&cp1_gpio1 8 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&cp1_sfp_pins>; - /* - * SFP cages are unconnected on early PCBs because of an the I2C - * lanes not being connected. Prevent the port for being - * unusable by disabling the SFP node. - */ - status = "disabled"; - }; + model = "Marvell Armada CN9131-DB setup A"; }; -/* - * Instantiate the first slave CP115 +/* Setup A has SPI1 flash as a boot device, while setup B uses NAND flash. + * Since CP0 SPI1 and CP0 NAND are sharing some pins, they cannot be activated + * simultaneously. When SPI controller is enabled, NAND should be disabled. */ -#define CP11X_NAME cp1 -#define CP11X_BASE f4000000 -#define CP11X_PCIEx_MEM_BASE(iface) (0xe2000000 + (iface * 0x1000000)) -#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000 -#define CP11X_PCIE0_BASE f4600000 -#define CP11X_PCIE1_BASE f4620000 -#define CP11X_PCIE2_BASE f4640000 - -#include "armada-cp115.dtsi" - -#undef CP11X_NAME -#undef CP11X_BASE -#undef CP11X_PCIEx_MEM_BASE -#undef CP11X_PCIEx_MEM_SIZE -#undef CP11X_PCIE0_BASE -#undef CP11X_PCIE1_BASE -#undef CP11X_PCIE2_BASE - -&cp1_crypto { - status = "disabled"; -}; - -&cp1_ethernet { - status = "okay"; -}; - -/* CON50 */ -&cp1_eth0 { - status = "disabled"; - phy-mode = "10gbase-kr"; - /* Generic PHY, providing serdes lanes */ - phys = <&cp1_comphy4 0>; - managed = "in-band-status"; - sfp = <&cp1_sfp_eth1>; -}; - -&cp1_gpio1 { - status = "okay"; -}; - -&cp1_gpio2 { - status = "okay"; -}; - -&cp1_i2c0 { +&cp0_spi1 { status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&cp1_i2c0_pins>; - clock-frequency = <100000>; }; -/* CON40 */ -&cp1_pcie0 { - pinctrl-names = "default"; - pinctrl-0 = <&cp1_pcie_reset_pins>; - num-lanes = <2>; - num-viewport = <8>; - marvell,reset-gpio = <&cp1_gpio1 0 GPIO_ACTIVE_HIGH>; - status = "okay"; - /* Generic PHY, providing serdes lanes */ - phys = <&cp1_comphy0 0 - &cp1_comphy1 0>; -}; - -&cp1_sata0 { - status = "okay"; - - /* CON32 */ - sata-port@1 { - /* Generic PHY, providing serdes lanes */ - phys = <&cp1_comphy5 1>; - }; -}; - -/* U24 */ -&cp1_spi1 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&cp1_spi0_pins>; - reg = <0x700680 0x50>; - - spi-flash@0 { - #address-cells = <0x1>; - #size-cells = <0x1>; - compatible = "jedec,spi-nor"; - reg = <0x0>; - /* On-board MUX does not allow higher frequencies */ - spi-max-frequency = <40000000>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "U-Boot-1"; - reg = <0x0 0x200000>; - }; - - partition@400000 { - label = "Filesystem-1"; - reg = <0x200000 0xe00000>; - }; - }; - }; - -}; - -&cp1_syscon0 { - cp1_pinctrl: pinctrl { - compatible = "marvell,cp115-standalone-pinctrl"; - - cp1_i2c0_pins: cp1-i2c-pins-0 { - marvell,pins = "mpp37", "mpp38"; - marvell,function = "i2c0"; - }; - cp1_spi0_pins: cp1-spi-pins-0 { - marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16"; - marvell,function = "spi1"; - }; - cp1_xhci0_vbus_pins: cp1-xhci0-vbus-pins { - marvell,pins = "mpp3"; - marvell,function = "gpio"; - }; - cp1_sfp_pins: sfp-pins { - marvell,pins = "mpp8", "mpp9", "mpp10", "mpp11"; - marvell,function = "gpio"; - }; - cp1_pcie_reset_pins: cp1-pcie-reset-pins { - marvell,pins = "mpp0"; - marvell,function = "gpio"; - }; - }; -}; - -/* CON58 */ -&cp1_usb3_1 { - status = "okay"; - usb-phy = <&cp1_usb3_0_phy0>; - /* Generic PHY, providing serdes lanes */ - phys = <&cp1_comphy3 1>; - phy-names = "usb"; -}; diff --git a/arch/arm64/boot/dts/marvell/cn9131-db.dtsi b/arch/arm64/boot/dts/marvell/cn9131-db.dtsi new file mode 100644 index 000000000000..82471a83ad6d --- /dev/null +++ b/arch/arm64/boot/dts/marvell/cn9131-db.dtsi @@ -0,0 +1,201 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2020 Marvell International Ltd. + * + * Device tree for the CN9131-DB board. + */ + +#include "cn9130-db.dtsi" + +/ { + compatible = "marvell,cn9131", "marvell,cn9130", + "marvell,armada-ap807-quad", "marvell,armada-ap807"; + + aliases { + gpio3 = &cp1_gpio1; + gpio4 = &cp1_gpio2; + ethernet3 = &cp1_eth0; + ethernet4 = &cp1_eth1; + }; + + cp1_reg_usb3_vbus0: cp1_usb3_vbus@0 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&cp1_xhci0_vbus_pins>; + regulator-name = "cp1-xhci0-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&cp1_gpio1 3 GPIO_ACTIVE_HIGH>; + }; + + cp1_usb3_0_phy0: cp1_usb3_phy0 { + compatible = "usb-nop-xceiv"; + vcc-supply = <&cp1_reg_usb3_vbus0>; + }; + + cp1_sfp_eth1: sfp-eth1 { + compatible = "sff,sfp"; + i2c-bus = <&cp1_i2c0>; + los-gpio = <&cp1_gpio1 11 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&cp1_gpio1 10 GPIO_ACTIVE_LOW>; + tx-disable-gpio = <&cp1_gpio1 9 GPIO_ACTIVE_HIGH>; + tx-fault-gpio = <&cp1_gpio1 8 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&cp1_sfp_pins>; + /* + * SFP cages are unconnected on early PCBs because of an the I2C + * lanes not being connected. Prevent the port for being + * unusable by disabling the SFP node. + */ + status = "disabled"; + }; +}; + +/* + * Instantiate the first slave CP115 + */ + +#define CP11X_NAME cp1 +#define CP11X_BASE f4000000 +#define CP11X_PCIEx_MEM_BASE(iface) (0xe2000000 + (iface * 0x1000000)) +#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000 +#define CP11X_PCIE0_BASE f4600000 +#define CP11X_PCIE1_BASE f4620000 +#define CP11X_PCIE2_BASE f4640000 + +#include "armada-cp115.dtsi" + +#undef CP11X_NAME +#undef CP11X_BASE +#undef CP11X_PCIEx_MEM_BASE +#undef CP11X_PCIEx_MEM_SIZE +#undef CP11X_PCIE0_BASE +#undef CP11X_PCIE1_BASE +#undef CP11X_PCIE2_BASE + +&cp1_crypto { + status = "disabled"; +}; + +&cp1_ethernet { + status = "okay"; +}; + +/* CON50 */ +&cp1_eth0 { + status = "disabled"; + phy-mode = "10gbase-kr"; + /* Generic PHY, providing serdes lanes */ + phys = <&cp1_comphy4 0>; + managed = "in-band-status"; + sfp = <&cp1_sfp_eth1>; +}; + +&cp1_gpio1 { + status = "okay"; +}; + +&cp1_gpio2 { + status = "okay"; +}; + +&cp1_i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&cp1_i2c0_pins>; + clock-frequency = <100000>; +}; + +/* CON40 */ +&cp1_pcie0 { + pinctrl-names = "default"; + pinctrl-0 = <&cp1_pcie_reset_pins>; + num-lanes = <2>; + num-viewport = <8>; + marvell,reset-gpio = <&cp1_gpio1 0 GPIO_ACTIVE_HIGH>; + status = "okay"; + /* Generic PHY, providing serdes lanes */ + phys = <&cp1_comphy0 0 + &cp1_comphy1 0>; +}; + +&cp1_sata0 { + status = "okay"; + + /* CON32 */ + sata-port@1 { + /* Generic PHY, providing serdes lanes */ + phys = <&cp1_comphy5 1>; + }; +}; + +/* U24 */ +&cp1_spi1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&cp1_spi0_pins>; + reg = <0x700680 0x50>; + + spi-flash@0 { + #address-cells = <0x1>; + #size-cells = <0x1>; + compatible = "jedec,spi-nor"; + reg = <0x0>; + /* On-board MUX does not allow higher frequencies */ + spi-max-frequency = <40000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "U-Boot-1"; + reg = <0x0 0x200000>; + }; + + partition@400000 { + label = "Filesystem-1"; + reg = <0x200000 0xe00000>; + }; + }; + }; + +}; + +&cp1_syscon0 { + cp1_pinctrl: pinctrl { + compatible = "marvell,cp115-standalone-pinctrl"; + + cp1_i2c0_pins: cp1-i2c-pins-0 { + marvell,pins = "mpp37", "mpp38"; + marvell,function = "i2c0"; + }; + cp1_spi0_pins: cp1-spi-pins-0 { + marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16"; + marvell,function = "spi1"; + }; + cp1_xhci0_vbus_pins: cp1-xhci0-vbus-pins { + marvell,pins = "mpp3"; + marvell,function = "gpio"; + }; + cp1_sfp_pins: sfp-pins { + marvell,pins = "mpp8", "mpp9", "mpp10", "mpp11"; + marvell,function = "gpio"; + }; + cp1_pcie_reset_pins: cp1-pcie-reset-pins { + marvell,pins = "mpp0"; + marvell,function = "gpio"; + }; + }; +}; + +/* CON58 */ +&cp1_usb3_1 { + status = "okay"; + usb-phy = <&cp1_usb3_0_phy0>; + /* Generic PHY, providing serdes lanes */ + phys = <&cp1_comphy3 1>; + phy-names = "usb"; +}; diff --git a/arch/arm64/boot/dts/marvell/cn9132-db-B.dts b/arch/arm64/boot/dts/marvell/cn9132-db-B.dts new file mode 100644 index 000000000000..7137a6f22d0f --- /dev/null +++ b/arch/arm64/boot/dts/marvell/cn9132-db-B.dts @@ -0,0 +1,22 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2019 Marvell International Ltd. + * + * Device tree for the CN9132-DB board. + */ + +#include "cn9132-db.dtsi" + +/ { + model = "Marvell Armada CN9132-DB setup B"; +}; + +/* Setup B has NAND flash as a boot device, while regular setup uses SPI flash. + * Since CP0 SPI1 and CP0 NAND are sharing some pins, they cannot be activated + * simultaneously. When NAND controller is enabled, SPI1 should be disabled. + */ + +&cp0_nand_controller { + status = "okay"; +}; + diff --git a/arch/arm64/boot/dts/marvell/cn9132-db.dts b/arch/arm64/boot/dts/marvell/cn9132-db.dts index 4ef0df3097ca..1f2e6377afc3 100644 --- a/arch/arm64/boot/dts/marvell/cn9132-db.dts +++ b/arch/arm64/boot/dts/marvell/cn9132-db.dts @@ -5,217 +5,18 @@ * Device tree for the CN9132-DB board. */ -#include "cn9131-db.dts" +#include "cn9132-db.dtsi" / { - model = "Marvell Armada CN9132-DB"; - compatible = "marvell,cn9132", "marvell,cn9131", "marvell,cn9130", - "marvell,armada-ap807-quad", "marvell,armada-ap807"; - - aliases { - gpio5 = &cp2_gpio1; - gpio6 = &cp2_gpio2; - ethernet5 = &cp2_eth0; - }; - - cp2_reg_usb3_vbus0: cp2_usb3_vbus@0 { - compatible = "regulator-fixed"; - regulator-name = "cp2-xhci0-vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - gpio = <&cp2_gpio1 2 GPIO_ACTIVE_HIGH>; - }; - - cp2_usb3_0_phy0: cp2_usb3_phy0 { - compatible = "usb-nop-xceiv"; - vcc-supply = <&cp2_reg_usb3_vbus0>; - }; - - cp2_reg_usb3_vbus1: cp2_usb3_vbus@1 { - compatible = "regulator-fixed"; - regulator-name = "cp2-xhci1-vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - gpio = <&cp2_gpio1 3 GPIO_ACTIVE_HIGH>; - }; - - cp2_usb3_0_phy1: cp2_usb3_phy1 { - compatible = "usb-nop-xceiv"; - vcc-supply = <&cp2_reg_usb3_vbus1>; - }; - - cp2_reg_sd_vccq: cp2_sd_vccq@0 { - compatible = "regulator-gpio"; - regulator-name = "cp2_sd_vcc"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - gpios = <&cp2_gpio2 17 GPIO_ACTIVE_HIGH>; - states = <1800000 0x1 3300000 0x0>; - }; - - cp2_sfp_eth0: sfp-eth0 { - compatible = "sff,sfp"; - i2c-bus = <&cp2_sfpp0_i2c>; - los-gpio = <&cp2_module_expander1 11 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&cp2_module_expander1 10 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&cp2_module_expander1 9 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&cp2_module_expander1 8 GPIO_ACTIVE_HIGH>; - /* - * SFP cages are unconnected on early PCBs because of an the I2C - * lanes not being connected. Prevent the port for being - * unusable by disabling the SFP node. - */ - status = "disabled"; - }; + model = "Marvell Armada CN9132-DB setup A"; }; -/* - * Instantiate the second slave CP115 +/* Setup A has SPI1 flash as a boot device, while setup B uses NAND flash. + * Since CP0 SPI1 and CP0 NAND are sharing some pins, they cannot be activated + * simultaneously. When SPI controller is enabled, NAND should be disabled. */ -#define CP11X_NAME cp2 -#define CP11X_BASE f6000000 -#define CP11X_PCIEx_MEM_BASE(iface) (0xe5000000 + (iface * 0x1000000)) -#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000 -#define CP11X_PCIE0_BASE f6600000 -#define CP11X_PCIE1_BASE f6620000 -#define CP11X_PCIE2_BASE f6640000 - -#include "armada-cp115.dtsi" - -#undef CP11X_NAME -#undef CP11X_BASE -#undef CP11X_PCIEx_MEM_BASE -#undef CP11X_PCIEx_MEM_SIZE -#undef CP11X_PCIE0_BASE -#undef CP11X_PCIE1_BASE -#undef CP11X_PCIE2_BASE - -&cp2_crypto { - status = "disabled"; -}; - -&cp2_ethernet { - status = "okay"; -}; - -/* SLM-1521-V2, CON9 */ -&cp2_eth0 { - status = "disabled"; - phy-mode = "10gbase-kr"; - /* Generic PHY, providing serdes lanes */ - phys = <&cp2_comphy4 0>; - managed = "in-band-status"; - sfp = <&cp2_sfp_eth0>; -}; - -&cp2_gpio1 { - status = "okay"; -}; - -&cp2_gpio2 { - status = "okay"; -}; - -&cp2_i2c0 { - clock-frequency = <100000>; - - /* SLM-1521-V2 - U3 */ - i2c-mux@72 { - compatible = "nxp,pca9544"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x72>; - cp2_sfpp0_i2c: i2c@0 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - }; - - i2c@1 { - #address-cells = <1>; - #size-cells = <0>; - reg = <1>; - /* U12 */ - cp2_module_expander1: pca9555@21 { - compatible = "nxp,pca9555"; - pinctrl-names = "default"; - gpio-controller; - #gpio-cells = <2>; - reg = <0x21>; - }; - }; - }; -}; - -/* SLM-1521-V2, CON6 */ -&cp2_pcie0 { - status = "okay"; - num-lanes = <2>; - num-viewport = <8>; - /* Generic PHY, providing serdes lanes */ - phys = <&cp2_comphy0 0 - &cp2_comphy1 0>; -}; - -/* SLM-1521-V2, CON8 */ -&cp2_pcie2 { - status = "okay"; - num-lanes = <1>; - num-viewport = <8>; - /* Generic PHY, providing serdes lanes */ - phys = <&cp2_comphy5 2>; -}; - -&cp2_sata0 { +&cp0_spi1 { status = "okay"; - - /* SLM-1521-V2, CON4 */ - sata-port@0 { - /* Generic PHY, providing serdes lanes */ - phys = <&cp2_comphy2 0>; - }; }; -/* CON 2 on SLM-1683 - microSD */ -&cp2_sdhci0 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&cp2_sdhci_pins>; - bus-width = <4>; - cd-gpios = <&cp2_gpio2 23 GPIO_ACTIVE_LOW>; - vqmmc-supply = <&cp2_reg_sd_vccq>; -}; - -&cp2_syscon0 { - cp2_pinctrl: pinctrl { - compatible = "marvell,cp115-standalone-pinctrl"; - - cp2_i2c0_pins: cp2-i2c-pins-0 { - marvell,pins = "mpp37", "mpp38"; - marvell,function = "i2c0"; - }; - cp2_sdhci_pins: cp2-sdhi-pins-0 { - marvell,pins = "mpp56", "mpp57", "mpp58", - "mpp59", "mpp60", "mpp61"; - marvell,function = "sdio"; - }; - }; -}; - -&cp2_usb3_0 { - status = "okay"; - usb-phy = <&cp2_usb3_0_phy0>; - phy-names = "usb"; -}; - -/* SLM-1521-V2, CON11 */ -&cp2_usb3_1 { - status = "okay"; - usb-phy = <&cp2_usb3_0_phy1>; - phy-names = "usb"; - /* Generic PHY, providing serdes lanes */ - phys = <&cp2_comphy3 1>; -}; diff --git a/arch/arm64/boot/dts/marvell/cn9132-db.dtsi b/arch/arm64/boot/dts/marvell/cn9132-db.dtsi new file mode 100644 index 000000000000..0c2d9f57318b --- /dev/null +++ b/arch/arm64/boot/dts/marvell/cn9132-db.dtsi @@ -0,0 +1,220 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2020 Marvell International Ltd. + * + * Device tree for the CN9132-DB board. + */ + +#include "cn9131-db.dtsi" + +/ { + compatible = "marvell,cn9132", "marvell,cn9131", "marvell,cn9130", + "marvell,armada-ap807-quad", "marvell,armada-ap807"; + + aliases { + gpio5 = &cp2_gpio1; + gpio6 = &cp2_gpio2; + ethernet5 = &cp2_eth0; + }; + + cp2_reg_usb3_vbus0: cp2_usb3_vbus@0 { + compatible = "regulator-fixed"; + regulator-name = "cp2-xhci0-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&cp2_gpio1 2 GPIO_ACTIVE_HIGH>; + }; + + cp2_usb3_0_phy0: cp2_usb3_phy0 { + compatible = "usb-nop-xceiv"; + vcc-supply = <&cp2_reg_usb3_vbus0>; + }; + + cp2_reg_usb3_vbus1: cp2_usb3_vbus@1 { + compatible = "regulator-fixed"; + regulator-name = "cp2-xhci1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&cp2_gpio1 3 GPIO_ACTIVE_HIGH>; + }; + + cp2_usb3_0_phy1: cp2_usb3_phy1 { + compatible = "usb-nop-xceiv"; + vcc-supply = <&cp2_reg_usb3_vbus1>; + }; + + cp2_reg_sd_vccq: cp2_sd_vccq@0 { + compatible = "regulator-gpio"; + regulator-name = "cp2_sd_vcc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + gpios = <&cp2_gpio2 17 GPIO_ACTIVE_HIGH>; + states = <1800000 0x1 3300000 0x0>; + }; + + cp2_sfp_eth0: sfp-eth0 { + compatible = "sff,sfp"; + i2c-bus = <&cp2_sfpp0_i2c>; + los-gpio = <&cp2_module_expander1 11 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&cp2_module_expander1 10 GPIO_ACTIVE_LOW>; + tx-disable-gpio = <&cp2_module_expander1 9 GPIO_ACTIVE_HIGH>; + tx-fault-gpio = <&cp2_module_expander1 8 GPIO_ACTIVE_HIGH>; + /* + * SFP cages are unconnected on early PCBs because of an the I2C + * lanes not being connected. Prevent the port for being + * unusable by disabling the SFP node. + */ + status = "disabled"; + }; +}; + +/* + * Instantiate the second slave CP115 + */ + +#define CP11X_NAME cp2 +#define CP11X_BASE f6000000 +#define CP11X_PCIEx_MEM_BASE(iface) (0xe5000000 + (iface * 0x1000000)) +#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000 +#define CP11X_PCIE0_BASE f6600000 +#define CP11X_PCIE1_BASE f6620000 +#define CP11X_PCIE2_BASE f6640000 + +#include "armada-cp115.dtsi" + +#undef CP11X_NAME +#undef CP11X_BASE +#undef CP11X_PCIEx_MEM_BASE +#undef CP11X_PCIEx_MEM_SIZE +#undef CP11X_PCIE0_BASE +#undef CP11X_PCIE1_BASE +#undef CP11X_PCIE2_BASE + +&cp2_crypto { + status = "disabled"; +}; + +&cp2_ethernet { + status = "okay"; +}; + +/* SLM-1521-V2, CON9 */ +&cp2_eth0 { + status = "disabled"; + phy-mode = "10gbase-kr"; + /* Generic PHY, providing serdes lanes */ + phys = <&cp2_comphy4 0>; + managed = "in-band-status"; + sfp = <&cp2_sfp_eth0>; +}; + +&cp2_gpio1 { + status = "okay"; +}; + +&cp2_gpio2 { + status = "okay"; +}; + +&cp2_i2c0 { + clock-frequency = <100000>; + + /* SLM-1521-V2 - U3 */ + i2c-mux@72 { + compatible = "nxp,pca9544"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x72>; + cp2_sfpp0_i2c: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + /* U12 */ + cp2_module_expander1: pca9555@21 { + compatible = "nxp,pca9555"; + pinctrl-names = "default"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x21>; + }; + }; + }; +}; + +/* SLM-1521-V2, CON6 */ +&cp2_pcie0 { + status = "okay"; + num-lanes = <2>; + num-viewport = <8>; + /* Generic PHY, providing serdes lanes */ + phys = <&cp2_comphy0 0 + &cp2_comphy1 0>; +}; + +/* SLM-1521-V2, CON8 */ +&cp2_pcie2 { + status = "okay"; + num-lanes = <1>; + num-viewport = <8>; + /* Generic PHY, providing serdes lanes */ + phys = <&cp2_comphy5 2>; +}; + +&cp2_sata0 { + status = "okay"; + + /* SLM-1521-V2, CON4 */ + sata-port@0 { + /* Generic PHY, providing serdes lanes */ + phys = <&cp2_comphy2 0>; + }; +}; + +/* CON 2 on SLM-1683 - microSD */ +&cp2_sdhci0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&cp2_sdhci_pins>; + bus-width = <4>; + cd-gpios = <&cp2_gpio2 23 GPIO_ACTIVE_LOW>; + vqmmc-supply = <&cp2_reg_sd_vccq>; +}; + +&cp2_syscon0 { + cp2_pinctrl: pinctrl { + compatible = "marvell,cp115-standalone-pinctrl"; + + cp2_i2c0_pins: cp2-i2c-pins-0 { + marvell,pins = "mpp37", "mpp38"; + marvell,function = "i2c0"; + }; + cp2_sdhci_pins: cp2-sdhi-pins-0 { + marvell,pins = "mpp56", "mpp57", "mpp58", + "mpp59", "mpp60", "mpp61"; + marvell,function = "sdio"; + }; + }; +}; + +&cp2_usb3_0 { + status = "okay"; + usb-phy = <&cp2_usb3_0_phy0>; + phy-names = "usb"; +}; + +/* SLM-1521-V2, CON11 */ +&cp2_usb3_1 { + status = "okay"; + usb-phy = <&cp2_usb3_0_phy1>; + phy-names = "usb"; + /* Generic PHY, providing serdes lanes */ + phys = <&cp2_comphy3 1>; +}; -- 2.17.1 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v4 3/5] arm64: dts: cn913x: add device trees for topology B boards @ 2021-02-09 13:46 ` kostap 0 siblings, 0 replies; 18+ messages in thread From: kostap @ 2021-02-09 13:46 UTC (permalink / raw) To: linux-kernel, devicetree, linux-arm-kernel Cc: tmn505, andrew, nadavh, jaz, gregory.clement, vkoul, kishon, vladimir.vid, luka.kovacic, robh+dt, miquel.raynal, Konstantin Porotchkin, stefanc, mw, bpeled, sebastian.hesselbarth From: Konstantin Porotchkin <kostap@marvell.com> The CN913x DB with topology B is similar to a regular setup (A) boards, but uses NAND flash as a boot device, while topology A boards are booting from SPI flash. Since NAND and SPI on CN913x DB boards share some wires, they cannot be activated simultaneously. The DTS files for setup "B" are based on setup "A", in which the CP0 NAND controller enabled and CP0 SPI1 disabled. Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> --- arch/arm64/boot/dts/marvell/Makefile | 3 + arch/arm64/boot/dts/marvell/cn9130-db-B.dts | 22 ++ arch/arm64/boot/dts/marvell/cn9130-db.dts | 393 +------------------ arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 402 ++++++++++++++++++++ arch/arm64/boot/dts/marvell/cn9131-db-B.dts | 22 ++ arch/arm64/boot/dts/marvell/cn9131-db.dts | 192 +--------- arch/arm64/boot/dts/marvell/cn9131-db.dtsi | 201 ++++++++++ arch/arm64/boot/dts/marvell/cn9132-db-B.dts | 22 ++ arch/arm64/boot/dts/marvell/cn9132-db.dts | 211 +--------- arch/arm64/boot/dts/marvell/cn9132-db.dtsi | 220 +++++++++++ 10 files changed, 910 insertions(+), 778 deletions(-) create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dtsi diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile index 34efe0fb6f37..5e39f9774e68 100644 --- a/arch/arm64/boot/dts/marvell/Makefile +++ b/arch/arm64/boot/dts/marvell/Makefile @@ -16,5 +16,8 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin-singleshot.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-puzzle-m801.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-8080-db.dtb dtb-$(CONFIG_ARCH_MVEBU) += cn9130-db.dtb +dtb-$(CONFIG_ARCH_MVEBU) += cn9130-db-B.dtb dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db.dtb +dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db-B.dtb dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db.dtb +dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db-B.dtb diff --git a/arch/arm64/boot/dts/marvell/cn9130-db-B.dts b/arch/arm64/boot/dts/marvell/cn9130-db-B.dts new file mode 100644 index 000000000000..57e41cacd483 --- /dev/null +++ b/arch/arm64/boot/dts/marvell/cn9130-db-B.dts @@ -0,0 +1,22 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2020 Marvell International Ltd. + * + * Device tree for the CN9130-DB board (setup "B"). + */ + +#include "cn9130-db.dtsi" + +/ { + model = "Marvell Armada CN9130-DB setup B"; +}; + +/* Setup B has NAND flash as a boot device, while regular setup uses SPI flash. + * Since CP0 SPI1 and CP0 NAND are sharing some pins, they cannot be activated + * simultaneously. When NAND controller is enabled, SPI1 should be disabled. + */ + +&cp0_nand_controller { + status = "okay"; +}; + diff --git a/arch/arm64/boot/dts/marvell/cn9130-db.dts b/arch/arm64/boot/dts/marvell/cn9130-db.dts index d24294888400..994f347f2973 100644 --- a/arch/arm64/boot/dts/marvell/cn9130-db.dts +++ b/arch/arm64/boot/dts/marvell/cn9130-db.dts @@ -5,399 +5,18 @@ * Device tree for the CN9130-DB board. */ -#include "cn9130.dtsi" - -#include <dt-bindings/gpio/gpio.h> +#include "cn9130-db.dtsi" / { - model = "Marvell Armada CN9130-DB"; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - aliases { - gpio1 = &cp0_gpio1; - gpio2 = &cp0_gpio2; - i2c0 = &cp0_i2c0; - ethernet0 = &cp0_eth0; - ethernet1 = &cp0_eth1; - ethernet2 = &cp0_eth2; - spi1 = &cp0_spi0; - spi2 = &cp0_spi1; - }; - - memory@00000000 { - device_type = "memory"; - reg = <0x0 0x0 0x0 0x80000000>; - }; - - ap0_reg_sd_vccq: ap0_sd_vccq@0 { - compatible = "regulator-gpio"; - regulator-name = "ap0_sd_vccq"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - gpios = <&expander0 8 GPIO_ACTIVE_HIGH>; - states = <1800000 0x1 3300000 0x0>; - }; - - cp0_reg_usb3_vbus0: cp0_usb3_vbus@0 { - compatible = "regulator-fixed"; - regulator-name = "cp0-xhci0-vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - gpio = <&expander0 0 GPIO_ACTIVE_HIGH>; - }; - - cp0_usb3_0_phy0: cp0_usb3_phy@0 { - compatible = "usb-nop-xceiv"; - vcc-supply = <&cp0_reg_usb3_vbus0>; - }; - - cp0_reg_usb3_vbus1: cp0_usb3_vbus@1 { - compatible = "regulator-fixed"; - regulator-name = "cp0-xhci1-vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - gpio = <&expander0 1 GPIO_ACTIVE_HIGH>; - }; - - cp0_usb3_0_phy1: cp0_usb3_phy@1 { - compatible = "usb-nop-xceiv"; - vcc-supply = <&cp0_reg_usb3_vbus1>; - }; - - cp0_reg_sd_vccq: cp0_sd_vccq@0 { - compatible = "regulator-gpio"; - regulator-name = "cp0_sd_vccq"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - gpios = <&expander0 15 GPIO_ACTIVE_HIGH>; - states = <1800000 0x1 - 3300000 0x0>; - }; - - cp0_reg_sd_vcc: cp0_sd_vcc@0 { - compatible = "regulator-fixed"; - regulator-name = "cp0_sd_vcc"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&expander0 14 GPIO_ACTIVE_HIGH>; - enable-active-high; - regulator-always-on; - }; - - cp0_sfp_eth0: sfp-eth@0 { - compatible = "sff,sfp"; - i2c-bus = <&cp0_sfpp0_i2c>; - los-gpio = <&cp0_module_expander1 11 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&cp0_module_expander1 10 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&cp0_module_expander1 9 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&cp0_module_expander1 8 GPIO_ACTIVE_HIGH>; - /* - * SFP cages are unconnected on early PCBs because of an the I2C - * lanes not being connected. Prevent the port for being - * unusable by disabling the SFP node. - */ - status = "disabled"; - }; -}; - -&uart0 { - status = "okay"; -}; - -/* on-board eMMC - U9 */ -&ap_sdhci0 { - pinctrl-names = "default"; - bus-width = <8>; - vqmmc-supply = <&ap0_reg_sd_vccq>; - status = "okay"; + model = "Marvell Armada CN9130-DB setup A"; }; -&cp0_crypto { - status = "disabled"; -}; - -&cp0_ethernet { - status = "okay"; -}; - -/* SLM-1521-V2, CON9 */ -&cp0_eth0 { - status = "disabled"; - phy-mode = "10gbase-kr"; - /* Generic PHY, providing serdes lanes */ - phys = <&cp0_comphy4 0>; - managed = "in-band-status"; - sfp = <&cp0_sfp_eth0>; -}; - -/* CON56 */ -&cp0_eth1 { - status = "okay"; - phy = <&phy0>; - phy-mode = "rgmii-id"; -}; - -/* CON57 */ -&cp0_eth2 { - status = "okay"; - phy = <&phy1>; - phy-mode = "rgmii-id"; -}; - -&cp0_gpio1 { - status = "okay"; -}; - -&cp0_gpio2 { - status = "okay"; -}; - -&cp0_i2c0 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&cp0_i2c0_pins>; - clock-frequency = <100000>; - - /* U36 */ - expander0: pca953x@21 { - compatible = "nxp,pca9555"; - pinctrl-names = "default"; - gpio-controller; - #gpio-cells = <2>; - reg = <0x21>; - status = "okay"; - }; - - /* U42 */ - eeprom0: eeprom@50 { - compatible = "atmel,24c64"; - reg = <0x50>; - pagesize = <0x20>; - }; - - /* U38 */ - eeprom1: eeprom@57 { - compatible = "atmel,24c64"; - reg = <0x57>; - pagesize = <0x20>; - }; -}; - -&cp0_i2c1 { - status = "okay"; - clock-frequency = <100000>; - - /* SLM-1521-V2 - U3 */ - i2c-mux@72 { /* verify address - depends on dpr */ - compatible = "nxp,pca9544"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x72>; - cp0_sfpp0_i2c: i2c@0 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - }; - - i2c@1 { - #address-cells = <1>; - #size-cells = <0>; - reg = <1>; - /* U12 */ - cp0_module_expander1: pca9555@21 { - compatible = "nxp,pca9555"; - pinctrl-names = "default"; - gpio-controller; - #gpio-cells = <2>; - reg = <0x21>; - }; - - }; - }; -}; - -&cp0_mdio { - status = "okay"; - - phy0: ethernet-phy@0 { - reg = <0>; - }; - - phy1: ethernet-phy@1 { - reg = <1>; - }; -}; - -/* U54 */ -&cp0_nand_controller { - pinctrl-names = "default"; - pinctrl-0 = <&nand_pins &nand_rb>; - - nand@0 { - reg = <0>; - label = "main-storage"; - nand-rb = <0>; - nand-ecc-mode = "hw"; - nand-on-flash-bbt; - nand-ecc-strength = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "U-Boot"; - reg = <0 0x200000>; - }; - partition@200000 { - label = "Linux"; - reg = <0x200000 0xe00000>; - }; - partition@1000000 { - label = "Filesystem"; - reg = <0x1000000 0x3f000000>; - }; - }; - }; -}; - -/* SLM-1521-V2, CON6 */ -&cp0_pcie0 { - status = "okay"; - num-lanes = <4>; - num-viewport = <8>; - /* Generic PHY, providing serdes lanes */ - phys = <&cp0_comphy0 0 - &cp0_comphy1 0 - &cp0_comphy2 0 - &cp0_comphy3 0>; -}; - -&cp0_sata0 { - status = "okay"; - - /* SLM-1521-V2, CON2 */ - sata-port@1 { - status = "okay"; - /* Generic PHY, providing serdes lanes */ - phys = <&cp0_comphy5 1>; - }; -}; - -/* CON 28 */ -&cp0_sdhci0 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&cp0_sdhci_pins - &cp0_sdhci_cd_pins>; - bus-width = <4>; - cd-gpios = <&cp0_gpio2 11 GPIO_ACTIVE_LOW>; - no-1-8-v; - vqmmc-supply = <&cp0_reg_sd_vccq>; - vmmc-supply = <&cp0_reg_sd_vcc>; -}; +/* Setup A has SPI1 flash as a boot device, while setup B uses NAND flash. + * Since CP0 SPI1 and CP0 NAND are sharing some pins, they cannot be activated + * simultaneously. When SPI controller is enabled, NAND should be disabled. + */ -/* U55 */ &cp0_spi1 { status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&cp0_spi0_pins>; - reg = <0x700680 0x50>; - - spi-flash@0 { - #address-cells = <0x1>; - #size-cells = <0x1>; - compatible = "jedec,spi-nor"; - reg = <0x0>; - /* On-board MUX does not allow higher frequencies */ - spi-max-frequency = <40000000>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "U-Boot-0"; - reg = <0x0 0x200000>; - }; - - partition@400000 { - label = "Filesystem-0"; - reg = <0x200000 0xe00000>; - }; - }; - }; -}; - -&cp0_syscon0 { - cp0_pinctrl: pinctrl { - compatible = "marvell,cp115-standalone-pinctrl"; - - cp0_i2c0_pins: cp0-i2c-pins-0 { - marvell,pins = "mpp37", "mpp38"; - marvell,function = "i2c0"; - }; - cp0_i2c1_pins: cp0-i2c-pins-1 { - marvell,pins = "mpp35", "mpp36"; - marvell,function = "i2c1"; - }; - cp0_ge1_rgmii_pins: cp0-ge-rgmii-pins-0 { - marvell,pins = "mpp0", "mpp1", "mpp2", - "mpp3", "mpp4", "mpp5", - "mpp6", "mpp7", "mpp8", - "mpp9", "mpp10", "mpp11"; - marvell,function = "ge0"; - }; - cp0_ge2_rgmii_pins: cp0-ge-rgmii-pins-1 { - marvell,pins = "mpp44", "mpp45", "mpp46", - "mpp47", "mpp48", "mpp49", - "mpp50", "mpp51", "mpp52", - "mpp53", "mpp54", "mpp55"; - marvell,function = "ge1"; - }; - cp0_sdhci_cd_pins: cp0-sdhci-cd-pins-0 { - marvell,pins = "mpp43"; - marvell,function = "gpio"; - }; - cp0_sdhci_pins: cp0-sdhi-pins-0 { - marvell,pins = "mpp56", "mpp57", "mpp58", - "mpp59", "mpp60", "mpp61"; - marvell,function = "sdio"; - }; - cp0_spi0_pins: cp0-spi-pins-0 { - marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16"; - marvell,function = "spi1"; - }; - nand_pins: nand-pins { - marvell,pins = "mpp15", "mpp16", "mpp17", "mpp18", - "mpp19", "mpp20", "mpp21", "mpp22", - "mpp23", "mpp24", "mpp25", "mpp26", - "mpp27"; - marvell,function = "dev"; - }; - nand_rb: nand-rb { - marvell,pins = "mpp13"; - marvell,function = "nf"; - }; - }; -}; - -&cp0_usb3_0 { - status = "okay"; - usb-phy = <&cp0_usb3_0_phy0>; - phy-names = "usb"; }; -&cp0_usb3_1 { - status = "okay"; - usb-phy = <&cp0_usb3_0_phy1>; - phy-names = "usb"; -}; diff --git a/arch/arm64/boot/dts/marvell/cn9130-db.dtsi b/arch/arm64/boot/dts/marvell/cn9130-db.dtsi new file mode 100644 index 000000000000..8de3a552b806 --- /dev/null +++ b/arch/arm64/boot/dts/marvell/cn9130-db.dtsi @@ -0,0 +1,402 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2019 Marvell International Ltd. + * + * Device tree for the CN9130-DB board. + */ + +#include "cn9130.dtsi" + +#include <dt-bindings/gpio/gpio.h> + +/ { + chosen { + stdout-path = "serial0:115200n8"; + }; + + aliases { + gpio1 = &cp0_gpio1; + gpio2 = &cp0_gpio2; + i2c0 = &cp0_i2c0; + ethernet0 = &cp0_eth0; + ethernet1 = &cp0_eth1; + ethernet2 = &cp0_eth2; + spi1 = &cp0_spi0; + spi2 = &cp0_spi1; + }; + + memory@00000000 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + ap0_reg_sd_vccq: ap0_sd_vccq@0 { + compatible = "regulator-gpio"; + regulator-name = "ap0_sd_vccq"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + gpios = <&expander0 8 GPIO_ACTIVE_HIGH>; + states = <1800000 0x1 3300000 0x0>; + }; + + cp0_reg_usb3_vbus0: cp0_usb3_vbus@0 { + compatible = "regulator-fixed"; + regulator-name = "cp0-xhci0-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&expander0 0 GPIO_ACTIVE_HIGH>; + }; + + cp0_usb3_0_phy0: cp0_usb3_phy@0 { + compatible = "usb-nop-xceiv"; + vcc-supply = <&cp0_reg_usb3_vbus0>; + }; + + cp0_reg_usb3_vbus1: cp0_usb3_vbus@1 { + compatible = "regulator-fixed"; + regulator-name = "cp0-xhci1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&expander0 1 GPIO_ACTIVE_HIGH>; + }; + + cp0_usb3_0_phy1: cp0_usb3_phy@1 { + compatible = "usb-nop-xceiv"; + vcc-supply = <&cp0_reg_usb3_vbus1>; + }; + + cp0_reg_sd_vccq: cp0_sd_vccq@0 { + compatible = "regulator-gpio"; + regulator-name = "cp0_sd_vccq"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + gpios = <&expander0 15 GPIO_ACTIVE_HIGH>; + states = <1800000 0x1 + 3300000 0x0>; + }; + + cp0_reg_sd_vcc: cp0_sd_vcc@0 { + compatible = "regulator-fixed"; + regulator-name = "cp0_sd_vcc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&expander0 14 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + cp0_sfp_eth0: sfp-eth@0 { + compatible = "sff,sfp"; + i2c-bus = <&cp0_sfpp0_i2c>; + los-gpio = <&cp0_module_expander1 11 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&cp0_module_expander1 10 GPIO_ACTIVE_LOW>; + tx-disable-gpio = <&cp0_module_expander1 9 GPIO_ACTIVE_HIGH>; + tx-fault-gpio = <&cp0_module_expander1 8 GPIO_ACTIVE_HIGH>; + /* + * SFP cages are unconnected on early PCBs because of an the I2C + * lanes not being connected. Prevent the port for being + * unusable by disabling the SFP node. + */ + status = "disabled"; + }; +}; + +&uart0 { + status = "okay"; +}; + +/* on-board eMMC - U9 */ +&ap_sdhci0 { + pinctrl-names = "default"; + bus-width = <8>; + vqmmc-supply = <&ap0_reg_sd_vccq>; + status = "okay"; +}; + +&cp0_crypto { + status = "disabled"; +}; + +&cp0_ethernet { + status = "okay"; +}; + +/* SLM-1521-V2, CON9 */ +&cp0_eth0 { + status = "disabled"; + phy-mode = "10gbase-kr"; + /* Generic PHY, providing serdes lanes */ + phys = <&cp0_comphy4 0>; + managed = "in-band-status"; + sfp = <&cp0_sfp_eth0>; +}; + +/* CON56 */ +&cp0_eth1 { + status = "okay"; + phy = <&phy0>; + phy-mode = "rgmii-id"; +}; + +/* CON57 */ +&cp0_eth2 { + status = "okay"; + phy = <&phy1>; + phy-mode = "rgmii-id"; +}; + +&cp0_gpio1 { + status = "okay"; +}; + +&cp0_gpio2 { + status = "okay"; +}; + +&cp0_i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_i2c0_pins>; + clock-frequency = <100000>; + + /* U36 */ + expander0: pca953x@21 { + compatible = "nxp,pca9555"; + pinctrl-names = "default"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x21>; + status = "okay"; + }; + + /* U42 */ + eeprom0: eeprom@50 { + compatible = "atmel,24c64"; + reg = <0x50>; + pagesize = <0x20>; + }; + + /* U38 */ + eeprom1: eeprom@57 { + compatible = "atmel,24c64"; + reg = <0x57>; + pagesize = <0x20>; + }; +}; + +&cp0_i2c1 { + status = "okay"; + clock-frequency = <100000>; + + /* SLM-1521-V2 - U3 */ + i2c-mux@72 { /* verify address - depends on dpr */ + compatible = "nxp,pca9544"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x72>; + cp0_sfpp0_i2c: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + /* U12 */ + cp0_module_expander1: pca9555@21 { + compatible = "nxp,pca9555"; + pinctrl-names = "default"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x21>; + }; + + }; + }; +}; + +&cp0_mdio { + status = "okay"; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; +}; + +/* U54 */ +&cp0_nand_controller { + status = "disabled"; + pinctrl-names = "default"; + pinctrl-0 = <&nand_pins &nand_rb>; + + nand@0 { + reg = <0>; + label = "main-storage"; + nand-rb = <0>; + nand-ecc-mode = "hw"; + nand-on-flash-bbt; + nand-ecc-strength = <8>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "U-Boot"; + reg = <0 0x200000>; + }; + partition@200000 { + label = "Linux"; + reg = <0x200000 0xe00000>; + }; + partition@1000000 { + label = "Filesystem"; + reg = <0x1000000 0x3f000000>; + }; + }; + }; +}; + +/* SLM-1521-V2, CON6 */ +&cp0_pcie0 { + status = "okay"; + num-lanes = <4>; + num-viewport = <8>; + /* Generic PHY, providing serdes lanes */ + phys = <&cp0_comphy0 0 + &cp0_comphy1 0 + &cp0_comphy2 0 + &cp0_comphy3 0>; +}; + +&cp0_sata0 { + status = "okay"; + + /* SLM-1521-V2, CON2 */ + sata-port@1 { + status = "okay"; + /* Generic PHY, providing serdes lanes */ + phys = <&cp0_comphy5 1>; + }; +}; + +/* CON 28 */ +&cp0_sdhci0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_sdhci_pins + &cp0_sdhci_cd_pins>; + bus-width = <4>; + cd-gpios = <&cp0_gpio2 11 GPIO_ACTIVE_LOW>; + no-1-8-v; + vqmmc-supply = <&cp0_reg_sd_vccq>; + vmmc-supply = <&cp0_reg_sd_vcc>; +}; + +/* U55 */ +&cp0_spi1 { + status = "disabled"; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_spi0_pins>; + reg = <0x700680 0x50>; + + spi-flash@0 { + #address-cells = <0x1>; + #size-cells = <0x1>; + compatible = "jedec,spi-nor"; + reg = <0x0>; + /* On-board MUX does not allow higher frequencies */ + spi-max-frequency = <40000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "U-Boot-0"; + reg = <0x0 0x200000>; + }; + + partition@400000 { + label = "Filesystem-0"; + reg = <0x200000 0xe00000>; + }; + }; + }; +}; + +&cp0_syscon0 { + cp0_pinctrl: pinctrl { + compatible = "marvell,cp115-standalone-pinctrl"; + + cp0_i2c0_pins: cp0-i2c-pins-0 { + marvell,pins = "mpp37", "mpp38"; + marvell,function = "i2c0"; + }; + cp0_i2c1_pins: cp0-i2c-pins-1 { + marvell,pins = "mpp35", "mpp36"; + marvell,function = "i2c1"; + }; + cp0_ge1_rgmii_pins: cp0-ge-rgmii-pins-0 { + marvell,pins = "mpp0", "mpp1", "mpp2", + "mpp3", "mpp4", "mpp5", + "mpp6", "mpp7", "mpp8", + "mpp9", "mpp10", "mpp11"; + marvell,function = "ge0"; + }; + cp0_ge2_rgmii_pins: cp0-ge-rgmii-pins-1 { + marvell,pins = "mpp44", "mpp45", "mpp46", + "mpp47", "mpp48", "mpp49", + "mpp50", "mpp51", "mpp52", + "mpp53", "mpp54", "mpp55"; + marvell,function = "ge1"; + }; + cp0_sdhci_cd_pins: cp0-sdhci-cd-pins-0 { + marvell,pins = "mpp43"; + marvell,function = "gpio"; + }; + cp0_sdhci_pins: cp0-sdhi-pins-0 { + marvell,pins = "mpp56", "mpp57", "mpp58", + "mpp59", "mpp60", "mpp61"; + marvell,function = "sdio"; + }; + cp0_spi0_pins: cp0-spi-pins-0 { + marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16"; + marvell,function = "spi1"; + }; + nand_pins: nand-pins { + marvell,pins = "mpp15", "mpp16", "mpp17", "mpp18", + "mpp19", "mpp20", "mpp21", "mpp22", + "mpp23", "mpp24", "mpp25", "mpp26", + "mpp27"; + marvell,function = "dev"; + }; + nand_rb: nand-rb { + marvell,pins = "mpp13"; + marvell,function = "nf"; + }; + }; +}; + +&cp0_usb3_0 { + status = "okay"; + usb-phy = <&cp0_usb3_0_phy0>; + phy-names = "usb"; +}; + +&cp0_usb3_1 { + status = "okay"; + usb-phy = <&cp0_usb3_0_phy1>; + phy-names = "usb"; +}; diff --git a/arch/arm64/boot/dts/marvell/cn9131-db-B.dts b/arch/arm64/boot/dts/marvell/cn9131-db-B.dts new file mode 100644 index 000000000000..183b1ec8b1f0 --- /dev/null +++ b/arch/arm64/boot/dts/marvell/cn9131-db-B.dts @@ -0,0 +1,22 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2020 Marvell International Ltd. + * + * Device tree for the CN9131-DB board (setup "B"). + */ + +#include "cn9131-db.dtsi" + +/ { + model = "Marvell Armada CN9131-DB setup B"; +}; + +/* Setup B has NAND flash as a boot device, while regular setup uses SPI flash. + * Since CP0 SPI1 and CP0 NAND are sharing some pins, they cannot be activated + * simultaneously. When NAND controller is enabled, SPI1 should be disabled. + */ + +&cp0_nand_controller { + status = "okay"; +}; + diff --git a/arch/arm64/boot/dts/marvell/cn9131-db.dts b/arch/arm64/boot/dts/marvell/cn9131-db.dts index 3c975f98b2a3..a60fdee79bf8 100644 --- a/arch/arm64/boot/dts/marvell/cn9131-db.dts +++ b/arch/arm64/boot/dts/marvell/cn9131-db.dts @@ -5,198 +5,18 @@ * Device tree for the CN9131-DB board. */ -#include "cn9130-db.dts" +#include "cn9131-db.dtsi" / { - model = "Marvell Armada CN9131-DB"; - compatible = "marvell,cn9131", "marvell,cn9130", - "marvell,armada-ap807-quad", "marvell,armada-ap807"; - - aliases { - gpio3 = &cp1_gpio1; - gpio4 = &cp1_gpio2; - ethernet3 = &cp1_eth0; - ethernet4 = &cp1_eth1; - }; - - cp1_reg_usb3_vbus0: cp1_usb3_vbus@0 { - compatible = "regulator-fixed"; - pinctrl-names = "default"; - pinctrl-0 = <&cp1_xhci0_vbus_pins>; - regulator-name = "cp1-xhci0-vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - gpio = <&cp1_gpio1 3 GPIO_ACTIVE_HIGH>; - }; - - cp1_usb3_0_phy0: cp1_usb3_phy0 { - compatible = "usb-nop-xceiv"; - vcc-supply = <&cp1_reg_usb3_vbus0>; - }; - - cp1_sfp_eth1: sfp-eth1 { - compatible = "sff,sfp"; - i2c-bus = <&cp1_i2c0>; - los-gpio = <&cp1_gpio1 11 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&cp1_gpio1 10 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&cp1_gpio1 9 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&cp1_gpio1 8 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&cp1_sfp_pins>; - /* - * SFP cages are unconnected on early PCBs because of an the I2C - * lanes not being connected. Prevent the port for being - * unusable by disabling the SFP node. - */ - status = "disabled"; - }; + model = "Marvell Armada CN9131-DB setup A"; }; -/* - * Instantiate the first slave CP115 +/* Setup A has SPI1 flash as a boot device, while setup B uses NAND flash. + * Since CP0 SPI1 and CP0 NAND are sharing some pins, they cannot be activated + * simultaneously. When SPI controller is enabled, NAND should be disabled. */ -#define CP11X_NAME cp1 -#define CP11X_BASE f4000000 -#define CP11X_PCIEx_MEM_BASE(iface) (0xe2000000 + (iface * 0x1000000)) -#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000 -#define CP11X_PCIE0_BASE f4600000 -#define CP11X_PCIE1_BASE f4620000 -#define CP11X_PCIE2_BASE f4640000 - -#include "armada-cp115.dtsi" - -#undef CP11X_NAME -#undef CP11X_BASE -#undef CP11X_PCIEx_MEM_BASE -#undef CP11X_PCIEx_MEM_SIZE -#undef CP11X_PCIE0_BASE -#undef CP11X_PCIE1_BASE -#undef CP11X_PCIE2_BASE - -&cp1_crypto { - status = "disabled"; -}; - -&cp1_ethernet { - status = "okay"; -}; - -/* CON50 */ -&cp1_eth0 { - status = "disabled"; - phy-mode = "10gbase-kr"; - /* Generic PHY, providing serdes lanes */ - phys = <&cp1_comphy4 0>; - managed = "in-band-status"; - sfp = <&cp1_sfp_eth1>; -}; - -&cp1_gpio1 { - status = "okay"; -}; - -&cp1_gpio2 { - status = "okay"; -}; - -&cp1_i2c0 { +&cp0_spi1 { status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&cp1_i2c0_pins>; - clock-frequency = <100000>; }; -/* CON40 */ -&cp1_pcie0 { - pinctrl-names = "default"; - pinctrl-0 = <&cp1_pcie_reset_pins>; - num-lanes = <2>; - num-viewport = <8>; - marvell,reset-gpio = <&cp1_gpio1 0 GPIO_ACTIVE_HIGH>; - status = "okay"; - /* Generic PHY, providing serdes lanes */ - phys = <&cp1_comphy0 0 - &cp1_comphy1 0>; -}; - -&cp1_sata0 { - status = "okay"; - - /* CON32 */ - sata-port@1 { - /* Generic PHY, providing serdes lanes */ - phys = <&cp1_comphy5 1>; - }; -}; - -/* U24 */ -&cp1_spi1 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&cp1_spi0_pins>; - reg = <0x700680 0x50>; - - spi-flash@0 { - #address-cells = <0x1>; - #size-cells = <0x1>; - compatible = "jedec,spi-nor"; - reg = <0x0>; - /* On-board MUX does not allow higher frequencies */ - spi-max-frequency = <40000000>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "U-Boot-1"; - reg = <0x0 0x200000>; - }; - - partition@400000 { - label = "Filesystem-1"; - reg = <0x200000 0xe00000>; - }; - }; - }; - -}; - -&cp1_syscon0 { - cp1_pinctrl: pinctrl { - compatible = "marvell,cp115-standalone-pinctrl"; - - cp1_i2c0_pins: cp1-i2c-pins-0 { - marvell,pins = "mpp37", "mpp38"; - marvell,function = "i2c0"; - }; - cp1_spi0_pins: cp1-spi-pins-0 { - marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16"; - marvell,function = "spi1"; - }; - cp1_xhci0_vbus_pins: cp1-xhci0-vbus-pins { - marvell,pins = "mpp3"; - marvell,function = "gpio"; - }; - cp1_sfp_pins: sfp-pins { - marvell,pins = "mpp8", "mpp9", "mpp10", "mpp11"; - marvell,function = "gpio"; - }; - cp1_pcie_reset_pins: cp1-pcie-reset-pins { - marvell,pins = "mpp0"; - marvell,function = "gpio"; - }; - }; -}; - -/* CON58 */ -&cp1_usb3_1 { - status = "okay"; - usb-phy = <&cp1_usb3_0_phy0>; - /* Generic PHY, providing serdes lanes */ - phys = <&cp1_comphy3 1>; - phy-names = "usb"; -}; diff --git a/arch/arm64/boot/dts/marvell/cn9131-db.dtsi b/arch/arm64/boot/dts/marvell/cn9131-db.dtsi new file mode 100644 index 000000000000..82471a83ad6d --- /dev/null +++ b/arch/arm64/boot/dts/marvell/cn9131-db.dtsi @@ -0,0 +1,201 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2020 Marvell International Ltd. + * + * Device tree for the CN9131-DB board. + */ + +#include "cn9130-db.dtsi" + +/ { + compatible = "marvell,cn9131", "marvell,cn9130", + "marvell,armada-ap807-quad", "marvell,armada-ap807"; + + aliases { + gpio3 = &cp1_gpio1; + gpio4 = &cp1_gpio2; + ethernet3 = &cp1_eth0; + ethernet4 = &cp1_eth1; + }; + + cp1_reg_usb3_vbus0: cp1_usb3_vbus@0 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&cp1_xhci0_vbus_pins>; + regulator-name = "cp1-xhci0-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&cp1_gpio1 3 GPIO_ACTIVE_HIGH>; + }; + + cp1_usb3_0_phy0: cp1_usb3_phy0 { + compatible = "usb-nop-xceiv"; + vcc-supply = <&cp1_reg_usb3_vbus0>; + }; + + cp1_sfp_eth1: sfp-eth1 { + compatible = "sff,sfp"; + i2c-bus = <&cp1_i2c0>; + los-gpio = <&cp1_gpio1 11 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&cp1_gpio1 10 GPIO_ACTIVE_LOW>; + tx-disable-gpio = <&cp1_gpio1 9 GPIO_ACTIVE_HIGH>; + tx-fault-gpio = <&cp1_gpio1 8 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&cp1_sfp_pins>; + /* + * SFP cages are unconnected on early PCBs because of an the I2C + * lanes not being connected. Prevent the port for being + * unusable by disabling the SFP node. + */ + status = "disabled"; + }; +}; + +/* + * Instantiate the first slave CP115 + */ + +#define CP11X_NAME cp1 +#define CP11X_BASE f4000000 +#define CP11X_PCIEx_MEM_BASE(iface) (0xe2000000 + (iface * 0x1000000)) +#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000 +#define CP11X_PCIE0_BASE f4600000 +#define CP11X_PCIE1_BASE f4620000 +#define CP11X_PCIE2_BASE f4640000 + +#include "armada-cp115.dtsi" + +#undef CP11X_NAME +#undef CP11X_BASE +#undef CP11X_PCIEx_MEM_BASE +#undef CP11X_PCIEx_MEM_SIZE +#undef CP11X_PCIE0_BASE +#undef CP11X_PCIE1_BASE +#undef CP11X_PCIE2_BASE + +&cp1_crypto { + status = "disabled"; +}; + +&cp1_ethernet { + status = "okay"; +}; + +/* CON50 */ +&cp1_eth0 { + status = "disabled"; + phy-mode = "10gbase-kr"; + /* Generic PHY, providing serdes lanes */ + phys = <&cp1_comphy4 0>; + managed = "in-band-status"; + sfp = <&cp1_sfp_eth1>; +}; + +&cp1_gpio1 { + status = "okay"; +}; + +&cp1_gpio2 { + status = "okay"; +}; + +&cp1_i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&cp1_i2c0_pins>; + clock-frequency = <100000>; +}; + +/* CON40 */ +&cp1_pcie0 { + pinctrl-names = "default"; + pinctrl-0 = <&cp1_pcie_reset_pins>; + num-lanes = <2>; + num-viewport = <8>; + marvell,reset-gpio = <&cp1_gpio1 0 GPIO_ACTIVE_HIGH>; + status = "okay"; + /* Generic PHY, providing serdes lanes */ + phys = <&cp1_comphy0 0 + &cp1_comphy1 0>; +}; + +&cp1_sata0 { + status = "okay"; + + /* CON32 */ + sata-port@1 { + /* Generic PHY, providing serdes lanes */ + phys = <&cp1_comphy5 1>; + }; +}; + +/* U24 */ +&cp1_spi1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&cp1_spi0_pins>; + reg = <0x700680 0x50>; + + spi-flash@0 { + #address-cells = <0x1>; + #size-cells = <0x1>; + compatible = "jedec,spi-nor"; + reg = <0x0>; + /* On-board MUX does not allow higher frequencies */ + spi-max-frequency = <40000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "U-Boot-1"; + reg = <0x0 0x200000>; + }; + + partition@400000 { + label = "Filesystem-1"; + reg = <0x200000 0xe00000>; + }; + }; + }; + +}; + +&cp1_syscon0 { + cp1_pinctrl: pinctrl { + compatible = "marvell,cp115-standalone-pinctrl"; + + cp1_i2c0_pins: cp1-i2c-pins-0 { + marvell,pins = "mpp37", "mpp38"; + marvell,function = "i2c0"; + }; + cp1_spi0_pins: cp1-spi-pins-0 { + marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16"; + marvell,function = "spi1"; + }; + cp1_xhci0_vbus_pins: cp1-xhci0-vbus-pins { + marvell,pins = "mpp3"; + marvell,function = "gpio"; + }; + cp1_sfp_pins: sfp-pins { + marvell,pins = "mpp8", "mpp9", "mpp10", "mpp11"; + marvell,function = "gpio"; + }; + cp1_pcie_reset_pins: cp1-pcie-reset-pins { + marvell,pins = "mpp0"; + marvell,function = "gpio"; + }; + }; +}; + +/* CON58 */ +&cp1_usb3_1 { + status = "okay"; + usb-phy = <&cp1_usb3_0_phy0>; + /* Generic PHY, providing serdes lanes */ + phys = <&cp1_comphy3 1>; + phy-names = "usb"; +}; diff --git a/arch/arm64/boot/dts/marvell/cn9132-db-B.dts b/arch/arm64/boot/dts/marvell/cn9132-db-B.dts new file mode 100644 index 000000000000..7137a6f22d0f --- /dev/null +++ b/arch/arm64/boot/dts/marvell/cn9132-db-B.dts @@ -0,0 +1,22 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2019 Marvell International Ltd. + * + * Device tree for the CN9132-DB board. + */ + +#include "cn9132-db.dtsi" + +/ { + model = "Marvell Armada CN9132-DB setup B"; +}; + +/* Setup B has NAND flash as a boot device, while regular setup uses SPI flash. + * Since CP0 SPI1 and CP0 NAND are sharing some pins, they cannot be activated + * simultaneously. When NAND controller is enabled, SPI1 should be disabled. + */ + +&cp0_nand_controller { + status = "okay"; +}; + diff --git a/arch/arm64/boot/dts/marvell/cn9132-db.dts b/arch/arm64/boot/dts/marvell/cn9132-db.dts index 4ef0df3097ca..1f2e6377afc3 100644 --- a/arch/arm64/boot/dts/marvell/cn9132-db.dts +++ b/arch/arm64/boot/dts/marvell/cn9132-db.dts @@ -5,217 +5,18 @@ * Device tree for the CN9132-DB board. */ -#include "cn9131-db.dts" +#include "cn9132-db.dtsi" / { - model = "Marvell Armada CN9132-DB"; - compatible = "marvell,cn9132", "marvell,cn9131", "marvell,cn9130", - "marvell,armada-ap807-quad", "marvell,armada-ap807"; - - aliases { - gpio5 = &cp2_gpio1; - gpio6 = &cp2_gpio2; - ethernet5 = &cp2_eth0; - }; - - cp2_reg_usb3_vbus0: cp2_usb3_vbus@0 { - compatible = "regulator-fixed"; - regulator-name = "cp2-xhci0-vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - gpio = <&cp2_gpio1 2 GPIO_ACTIVE_HIGH>; - }; - - cp2_usb3_0_phy0: cp2_usb3_phy0 { - compatible = "usb-nop-xceiv"; - vcc-supply = <&cp2_reg_usb3_vbus0>; - }; - - cp2_reg_usb3_vbus1: cp2_usb3_vbus@1 { - compatible = "regulator-fixed"; - regulator-name = "cp2-xhci1-vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - gpio = <&cp2_gpio1 3 GPIO_ACTIVE_HIGH>; - }; - - cp2_usb3_0_phy1: cp2_usb3_phy1 { - compatible = "usb-nop-xceiv"; - vcc-supply = <&cp2_reg_usb3_vbus1>; - }; - - cp2_reg_sd_vccq: cp2_sd_vccq@0 { - compatible = "regulator-gpio"; - regulator-name = "cp2_sd_vcc"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - gpios = <&cp2_gpio2 17 GPIO_ACTIVE_HIGH>; - states = <1800000 0x1 3300000 0x0>; - }; - - cp2_sfp_eth0: sfp-eth0 { - compatible = "sff,sfp"; - i2c-bus = <&cp2_sfpp0_i2c>; - los-gpio = <&cp2_module_expander1 11 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&cp2_module_expander1 10 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&cp2_module_expander1 9 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&cp2_module_expander1 8 GPIO_ACTIVE_HIGH>; - /* - * SFP cages are unconnected on early PCBs because of an the I2C - * lanes not being connected. Prevent the port for being - * unusable by disabling the SFP node. - */ - status = "disabled"; - }; + model = "Marvell Armada CN9132-DB setup A"; }; -/* - * Instantiate the second slave CP115 +/* Setup A has SPI1 flash as a boot device, while setup B uses NAND flash. + * Since CP0 SPI1 and CP0 NAND are sharing some pins, they cannot be activated + * simultaneously. When SPI controller is enabled, NAND should be disabled. */ -#define CP11X_NAME cp2 -#define CP11X_BASE f6000000 -#define CP11X_PCIEx_MEM_BASE(iface) (0xe5000000 + (iface * 0x1000000)) -#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000 -#define CP11X_PCIE0_BASE f6600000 -#define CP11X_PCIE1_BASE f6620000 -#define CP11X_PCIE2_BASE f6640000 - -#include "armada-cp115.dtsi" - -#undef CP11X_NAME -#undef CP11X_BASE -#undef CP11X_PCIEx_MEM_BASE -#undef CP11X_PCIEx_MEM_SIZE -#undef CP11X_PCIE0_BASE -#undef CP11X_PCIE1_BASE -#undef CP11X_PCIE2_BASE - -&cp2_crypto { - status = "disabled"; -}; - -&cp2_ethernet { - status = "okay"; -}; - -/* SLM-1521-V2, CON9 */ -&cp2_eth0 { - status = "disabled"; - phy-mode = "10gbase-kr"; - /* Generic PHY, providing serdes lanes */ - phys = <&cp2_comphy4 0>; - managed = "in-band-status"; - sfp = <&cp2_sfp_eth0>; -}; - -&cp2_gpio1 { - status = "okay"; -}; - -&cp2_gpio2 { - status = "okay"; -}; - -&cp2_i2c0 { - clock-frequency = <100000>; - - /* SLM-1521-V2 - U3 */ - i2c-mux@72 { - compatible = "nxp,pca9544"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x72>; - cp2_sfpp0_i2c: i2c@0 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - }; - - i2c@1 { - #address-cells = <1>; - #size-cells = <0>; - reg = <1>; - /* U12 */ - cp2_module_expander1: pca9555@21 { - compatible = "nxp,pca9555"; - pinctrl-names = "default"; - gpio-controller; - #gpio-cells = <2>; - reg = <0x21>; - }; - }; - }; -}; - -/* SLM-1521-V2, CON6 */ -&cp2_pcie0 { - status = "okay"; - num-lanes = <2>; - num-viewport = <8>; - /* Generic PHY, providing serdes lanes */ - phys = <&cp2_comphy0 0 - &cp2_comphy1 0>; -}; - -/* SLM-1521-V2, CON8 */ -&cp2_pcie2 { - status = "okay"; - num-lanes = <1>; - num-viewport = <8>; - /* Generic PHY, providing serdes lanes */ - phys = <&cp2_comphy5 2>; -}; - -&cp2_sata0 { +&cp0_spi1 { status = "okay"; - - /* SLM-1521-V2, CON4 */ - sata-port@0 { - /* Generic PHY, providing serdes lanes */ - phys = <&cp2_comphy2 0>; - }; }; -/* CON 2 on SLM-1683 - microSD */ -&cp2_sdhci0 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&cp2_sdhci_pins>; - bus-width = <4>; - cd-gpios = <&cp2_gpio2 23 GPIO_ACTIVE_LOW>; - vqmmc-supply = <&cp2_reg_sd_vccq>; -}; - -&cp2_syscon0 { - cp2_pinctrl: pinctrl { - compatible = "marvell,cp115-standalone-pinctrl"; - - cp2_i2c0_pins: cp2-i2c-pins-0 { - marvell,pins = "mpp37", "mpp38"; - marvell,function = "i2c0"; - }; - cp2_sdhci_pins: cp2-sdhi-pins-0 { - marvell,pins = "mpp56", "mpp57", "mpp58", - "mpp59", "mpp60", "mpp61"; - marvell,function = "sdio"; - }; - }; -}; - -&cp2_usb3_0 { - status = "okay"; - usb-phy = <&cp2_usb3_0_phy0>; - phy-names = "usb"; -}; - -/* SLM-1521-V2, CON11 */ -&cp2_usb3_1 { - status = "okay"; - usb-phy = <&cp2_usb3_0_phy1>; - phy-names = "usb"; - /* Generic PHY, providing serdes lanes */ - phys = <&cp2_comphy3 1>; -}; diff --git a/arch/arm64/boot/dts/marvell/cn9132-db.dtsi b/arch/arm64/boot/dts/marvell/cn9132-db.dtsi new file mode 100644 index 000000000000..0c2d9f57318b --- /dev/null +++ b/arch/arm64/boot/dts/marvell/cn9132-db.dtsi @@ -0,0 +1,220 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2020 Marvell International Ltd. + * + * Device tree for the CN9132-DB board. + */ + +#include "cn9131-db.dtsi" + +/ { + compatible = "marvell,cn9132", "marvell,cn9131", "marvell,cn9130", + "marvell,armada-ap807-quad", "marvell,armada-ap807"; + + aliases { + gpio5 = &cp2_gpio1; + gpio6 = &cp2_gpio2; + ethernet5 = &cp2_eth0; + }; + + cp2_reg_usb3_vbus0: cp2_usb3_vbus@0 { + compatible = "regulator-fixed"; + regulator-name = "cp2-xhci0-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&cp2_gpio1 2 GPIO_ACTIVE_HIGH>; + }; + + cp2_usb3_0_phy0: cp2_usb3_phy0 { + compatible = "usb-nop-xceiv"; + vcc-supply = <&cp2_reg_usb3_vbus0>; + }; + + cp2_reg_usb3_vbus1: cp2_usb3_vbus@1 { + compatible = "regulator-fixed"; + regulator-name = "cp2-xhci1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&cp2_gpio1 3 GPIO_ACTIVE_HIGH>; + }; + + cp2_usb3_0_phy1: cp2_usb3_phy1 { + compatible = "usb-nop-xceiv"; + vcc-supply = <&cp2_reg_usb3_vbus1>; + }; + + cp2_reg_sd_vccq: cp2_sd_vccq@0 { + compatible = "regulator-gpio"; + regulator-name = "cp2_sd_vcc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + gpios = <&cp2_gpio2 17 GPIO_ACTIVE_HIGH>; + states = <1800000 0x1 3300000 0x0>; + }; + + cp2_sfp_eth0: sfp-eth0 { + compatible = "sff,sfp"; + i2c-bus = <&cp2_sfpp0_i2c>; + los-gpio = <&cp2_module_expander1 11 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&cp2_module_expander1 10 GPIO_ACTIVE_LOW>; + tx-disable-gpio = <&cp2_module_expander1 9 GPIO_ACTIVE_HIGH>; + tx-fault-gpio = <&cp2_module_expander1 8 GPIO_ACTIVE_HIGH>; + /* + * SFP cages are unconnected on early PCBs because of an the I2C + * lanes not being connected. Prevent the port for being + * unusable by disabling the SFP node. + */ + status = "disabled"; + }; +}; + +/* + * Instantiate the second slave CP115 + */ + +#define CP11X_NAME cp2 +#define CP11X_BASE f6000000 +#define CP11X_PCIEx_MEM_BASE(iface) (0xe5000000 + (iface * 0x1000000)) +#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000 +#define CP11X_PCIE0_BASE f6600000 +#define CP11X_PCIE1_BASE f6620000 +#define CP11X_PCIE2_BASE f6640000 + +#include "armada-cp115.dtsi" + +#undef CP11X_NAME +#undef CP11X_BASE +#undef CP11X_PCIEx_MEM_BASE +#undef CP11X_PCIEx_MEM_SIZE +#undef CP11X_PCIE0_BASE +#undef CP11X_PCIE1_BASE +#undef CP11X_PCIE2_BASE + +&cp2_crypto { + status = "disabled"; +}; + +&cp2_ethernet { + status = "okay"; +}; + +/* SLM-1521-V2, CON9 */ +&cp2_eth0 { + status = "disabled"; + phy-mode = "10gbase-kr"; + /* Generic PHY, providing serdes lanes */ + phys = <&cp2_comphy4 0>; + managed = "in-band-status"; + sfp = <&cp2_sfp_eth0>; +}; + +&cp2_gpio1 { + status = "okay"; +}; + +&cp2_gpio2 { + status = "okay"; +}; + +&cp2_i2c0 { + clock-frequency = <100000>; + + /* SLM-1521-V2 - U3 */ + i2c-mux@72 { + compatible = "nxp,pca9544"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x72>; + cp2_sfpp0_i2c: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + /* U12 */ + cp2_module_expander1: pca9555@21 { + compatible = "nxp,pca9555"; + pinctrl-names = "default"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x21>; + }; + }; + }; +}; + +/* SLM-1521-V2, CON6 */ +&cp2_pcie0 { + status = "okay"; + num-lanes = <2>; + num-viewport = <8>; + /* Generic PHY, providing serdes lanes */ + phys = <&cp2_comphy0 0 + &cp2_comphy1 0>; +}; + +/* SLM-1521-V2, CON8 */ +&cp2_pcie2 { + status = "okay"; + num-lanes = <1>; + num-viewport = <8>; + /* Generic PHY, providing serdes lanes */ + phys = <&cp2_comphy5 2>; +}; + +&cp2_sata0 { + status = "okay"; + + /* SLM-1521-V2, CON4 */ + sata-port@0 { + /* Generic PHY, providing serdes lanes */ + phys = <&cp2_comphy2 0>; + }; +}; + +/* CON 2 on SLM-1683 - microSD */ +&cp2_sdhci0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&cp2_sdhci_pins>; + bus-width = <4>; + cd-gpios = <&cp2_gpio2 23 GPIO_ACTIVE_LOW>; + vqmmc-supply = <&cp2_reg_sd_vccq>; +}; + +&cp2_syscon0 { + cp2_pinctrl: pinctrl { + compatible = "marvell,cp115-standalone-pinctrl"; + + cp2_i2c0_pins: cp2-i2c-pins-0 { + marvell,pins = "mpp37", "mpp38"; + marvell,function = "i2c0"; + }; + cp2_sdhci_pins: cp2-sdhi-pins-0 { + marvell,pins = "mpp56", "mpp57", "mpp58", + "mpp59", "mpp60", "mpp61"; + marvell,function = "sdio"; + }; + }; +}; + +&cp2_usb3_0 { + status = "okay"; + usb-phy = <&cp2_usb3_0_phy0>; + phy-names = "usb"; +}; + +/* SLM-1521-V2, CON11 */ +&cp2_usb3_1 { + status = "okay"; + usb-phy = <&cp2_usb3_0_phy1>; + phy-names = "usb"; + /* Generic PHY, providing serdes lanes */ + phys = <&cp2_comphy3 1>; +}; -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v4 4/5] dts: marvell: Enable 10G interface on 9130-DB board 2021-02-09 13:46 ` kostap @ 2021-02-09 13:46 ` kostap -1 siblings, 0 replies; 18+ messages in thread From: kostap @ 2021-02-09 13:46 UTC (permalink / raw) To: linux-kernel, devicetree, linux-arm-kernel Cc: vladimir.vid, tmn505, luka.kovacic, sebastian.hesselbarth, gregory.clement, andrew, robh+dt, vkoul, kishon, miquel.raynal, mw, jaz, nadavh, stefanc, bpeled, Konstantin Porotchkin From: Stefan Chulski <stefanc@marvell.com> This patch enables eth0 10G interface on CN9130-DB paltforms. Signed-off-by: Stefan Chulski <stefanc@marvell.com> Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> --- arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/marvell/cn9130-db.dtsi b/arch/arm64/boot/dts/marvell/cn9130-db.dtsi index 8de3a552b806..97c74b81fd78 100644 --- a/arch/arm64/boot/dts/marvell/cn9130-db.dtsi +++ b/arch/arm64/boot/dts/marvell/cn9130-db.dtsi @@ -125,7 +125,7 @@ /* SLM-1521-V2, CON9 */ &cp0_eth0 { - status = "disabled"; + status = "okay"; phy-mode = "10gbase-kr"; /* Generic PHY, providing serdes lanes */ phys = <&cp0_comphy4 0>; -- 2.17.1 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v4 4/5] dts: marvell: Enable 10G interface on 9130-DB board @ 2021-02-09 13:46 ` kostap 0 siblings, 0 replies; 18+ messages in thread From: kostap @ 2021-02-09 13:46 UTC (permalink / raw) To: linux-kernel, devicetree, linux-arm-kernel Cc: tmn505, andrew, nadavh, jaz, gregory.clement, vkoul, kishon, vladimir.vid, luka.kovacic, robh+dt, miquel.raynal, Konstantin Porotchkin, stefanc, mw, bpeled, sebastian.hesselbarth From: Stefan Chulski <stefanc@marvell.com> This patch enables eth0 10G interface on CN9130-DB paltforms. Signed-off-by: Stefan Chulski <stefanc@marvell.com> Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> --- arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/marvell/cn9130-db.dtsi b/arch/arm64/boot/dts/marvell/cn9130-db.dtsi index 8de3a552b806..97c74b81fd78 100644 --- a/arch/arm64/boot/dts/marvell/cn9130-db.dtsi +++ b/arch/arm64/boot/dts/marvell/cn9130-db.dtsi @@ -125,7 +125,7 @@ /* SLM-1521-V2, CON9 */ &cp0_eth0 { - status = "disabled"; + status = "okay"; phy-mode = "10gbase-kr"; /* Generic PHY, providing serdes lanes */ phys = <&cp0_comphy4 0>; -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 18+ messages in thread
* Re: [PATCH v4 4/5] dts: marvell: Enable 10G interface on 9130-DB board 2021-02-09 13:46 ` kostap @ 2021-02-09 14:13 ` Marcin Wojtas -1 siblings, 0 replies; 18+ messages in thread From: Marcin Wojtas @ 2021-02-09 14:13 UTC (permalink / raw) To: Kostya Porotchkin Cc: Linux Kernel Mailing List, devicetree, linux-arm-kernel, Vladimir Vid, tmn505, luka.kovacic, Sebastian Hesselbarth, Grégory Clement, Andrew Lunn, Rob Herring, vkoul, kishon, Miquèl Raynal, Grzegorz Jaszczyk, nadavh, Stefan Chulski, Ben Peled (בן פלד) Hi, wt., 9 lut 2021 o 14:47 <kostap@marvell.com> napisał(a): > > From: Stefan Chulski <stefanc@marvell.com> > > This patch enables eth0 10G interface on CN9130-DB paltforms. > > Signed-off-by: Stefan Chulski <stefanc@marvell.com> > Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> > --- > arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 2 +- > 1 file changed, 1 insertion(+), 1 deletion(-) > > diff --git a/arch/arm64/boot/dts/marvell/cn9130-db.dtsi b/arch/arm64/boot/dts/marvell/cn9130-db.dtsi > index 8de3a552b806..97c74b81fd78 100644 > --- a/arch/arm64/boot/dts/marvell/cn9130-db.dtsi > +++ b/arch/arm64/boot/dts/marvell/cn9130-db.dtsi > @@ -125,7 +125,7 @@ > > /* SLM-1521-V2, CON9 */ > &cp0_eth0 { > - status = "disabled"; > + status = "okay"; > phy-mode = "10gbase-kr"; > /* Generic PHY, providing serdes lanes */ > phys = <&cp0_comphy4 0>; > -- > 2.17.1 > You can add my: Tested-by: Marcin Wojtas <mw@semihalf.com> Please do the same for cp1_eth0? Best regards, Marcin ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v4 4/5] dts: marvell: Enable 10G interface on 9130-DB board @ 2021-02-09 14:13 ` Marcin Wojtas 0 siblings, 0 replies; 18+ messages in thread From: Marcin Wojtas @ 2021-02-09 14:13 UTC (permalink / raw) To: Kostya Porotchkin Cc: tmn505, devicetree, nadavh, Andrew Lunn, Grzegorz Jaszczyk, Grégory Clement, Linux Kernel Mailing List, kishon, Vladimir Vid, luka.kovacic, Rob Herring, vkoul, Miquèl Raynal, Stefan Chulski, Ben Peled (בן פלד), linux-arm-kernel, Sebastian Hesselbarth Hi, wt., 9 lut 2021 o 14:47 <kostap@marvell.com> napisał(a): > > From: Stefan Chulski <stefanc@marvell.com> > > This patch enables eth0 10G interface on CN9130-DB paltforms. > > Signed-off-by: Stefan Chulski <stefanc@marvell.com> > Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> > --- > arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 2 +- > 1 file changed, 1 insertion(+), 1 deletion(-) > > diff --git a/arch/arm64/boot/dts/marvell/cn9130-db.dtsi b/arch/arm64/boot/dts/marvell/cn9130-db.dtsi > index 8de3a552b806..97c74b81fd78 100644 > --- a/arch/arm64/boot/dts/marvell/cn9130-db.dtsi > +++ b/arch/arm64/boot/dts/marvell/cn9130-db.dtsi > @@ -125,7 +125,7 @@ > > /* SLM-1521-V2, CON9 */ > &cp0_eth0 { > - status = "disabled"; > + status = "okay"; > phy-mode = "10gbase-kr"; > /* Generic PHY, providing serdes lanes */ > phys = <&cp0_comphy4 0>; > -- > 2.17.1 > You can add my: Tested-by: Marcin Wojtas <mw@semihalf.com> Please do the same for cp1_eth0? Best regards, Marcin _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v4 5/5] arm64: dts: add support for Marvell cn9130-crb platform 2021-02-09 13:46 ` kostap @ 2021-02-09 13:46 ` kostap -1 siblings, 0 replies; 18+ messages in thread From: kostap @ 2021-02-09 13:46 UTC (permalink / raw) To: linux-kernel, devicetree, linux-arm-kernel Cc: vladimir.vid, tmn505, luka.kovacic, sebastian.hesselbarth, gregory.clement, andrew, robh+dt, vkoul, kishon, miquel.raynal, mw, jaz, nadavh, stefanc, bpeled, Konstantin Porotchkin From: Konstantin Porotchkin <kostap@marvell.com> The Marvell reference platform CN9130-CRB is a small form factor board in a metal case. The platform is based on CN9130 SoC with addition of 8 Gigabit ports SOHO Ethernet switch. The reference platform features the following: * Up to 4 CPU cores ARMv8 Cortex-A72 CPU * CPU core operating speed of up to 2.2GHz * DDR4 DIMM – 8GB 64bit+ECC @ 2400Mhz. * 1x eMMC 8GB device * 1x uSD card 4 bits port on CP * 1x 128MB SPI NOR flash memory * 1x USB 3.0 Host port (Type A) * 1x SATA Gen3 via M.2 * 1x USB 3.0 via M.2 * 1x SIM card slot * 1x 1G Ethernet port via RGMII * 1x 10G switch port over SFP+ connector * 8x 1G ports through 88E6393X switch via XFI * 1x 2.5G/1G/100M/10M port via HS_SGMII * 1x PCI Express (PCIe)x1 Gen 3.0 * 1x PCI Express (PCIe)x4 Gen 3.0 via NVMe M.2 * JTAG port The CRB board uses MCP23017 i2c pin controller that drives the onboard eMMC abd USB 3,0 port power lines. The following configuration should be enabled for this controller support: CONFIG_PINCTRL_MCP23S08=y The plaform supports two HW configurations - "A" and "B" CN9130-CRB-A * AP-MPP configuration: SDIO, UART * CP0 Serdes configuration: * Lane0-3: NVMe (PCIe x4) * Lane4: XFI * Lane5: HS_SGMII 2. CN9130-CRB-B * AP-MPP configuration: SDIO, UART * CP0-MPP configuration: RGMII, SDIO, I2C0, I2C1, SMI, XSMI * CP0 Serdes configuration: * Lane0: PCIe x1 * Lane1: USB3_0 x1 * Lane2: SATA x1 * Lane3: USB3_1 x1 * Lane4: XFI * Lane5: HS_SGMII Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> --- arch/arm64/boot/dts/marvell/Makefile | 2 + arch/arm64/boot/dts/marvell/cn9130-crb-A.dts | 38 ++++ arch/arm64/boot/dts/marvell/cn9130-crb-B.dts | 46 ++++ arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 222 ++++++++++++++++++++ 4 files changed, 308 insertions(+) create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile index 5e39f9774e68..c686a8dd3ca5 100644 --- a/arch/arm64/boot/dts/marvell/Makefile +++ b/arch/arm64/boot/dts/marvell/Makefile @@ -21,3 +21,5 @@ dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db.dtb dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db-B.dtb dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db.dtb dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db-B.dtb +dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-A.dtb +dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-B.dtb diff --git a/arch/arm64/boot/dts/marvell/cn9130-crb-A.dts b/arch/arm64/boot/dts/marvell/cn9130-crb-A.dts new file mode 100644 index 000000000000..a7b6dfba8af5 --- /dev/null +++ b/arch/arm64/boot/dts/marvell/cn9130-crb-A.dts @@ -0,0 +1,38 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2020 Marvell International Ltd. + */ + +#include "cn9130-crb.dtsi" + +/ { + model = "Marvell Armada CN9130-CRB-A"; +}; + +&cp0_pcie0 { + status = "okay"; + num-lanes = <4>; + num-viewport = <8>; + /* Generic PHY, providing serdes lanes */ + phys = <&cp0_comphy0 0 + &cp0_comphy1 0 + &cp0_comphy2 0 + &cp0_comphy3 0>; + iommu-map = + <0x0 &smmu 0x480 0x20>, + <0x100 &smmu 0x4a0 0x20>, + <0x200 &smmu 0x4c0 0x20>; + iommu-map-mask = <0x031f>; +}; + +&cp0_usb3_0 { + status = "okay"; + usb-phy = <&cp0_usb3_0_phy0>; + phy-names = "usb"; +}; + +&cp0_usb3_1 { + status = "okay"; + usb-phy = <&cp0_usb3_0_phy1>; + phy-names = "usb"; +}; diff --git a/arch/arm64/boot/dts/marvell/cn9130-crb-B.dts b/arch/arm64/boot/dts/marvell/cn9130-crb-B.dts new file mode 100644 index 000000000000..0904cb0309ae --- /dev/null +++ b/arch/arm64/boot/dts/marvell/cn9130-crb-B.dts @@ -0,0 +1,46 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2020 Marvell International Ltd. + */ + +#include "cn9130-crb.dtsi" + +/ { + model = "Marvell Armada CN9130-CRB-B"; +}; + +&cp0_pcie0 { + status = "okay"; + num-lanes = <1>; + num-viewport = <8>; + /* Generic PHY, providing serdes lanes */ + phys = <&cp0_comphy0 0>; + iommu-map = + <0x0 &smmu 0x480 0x20>, + <0x100 &smmu 0x4a0 0x20>, + <0x200 &smmu 0x4c0 0x20>; + iommu-map-mask = <0x031f>; +}; + +&cp0_sata0 { + status = "okay"; + sata-port@0 { + status = "okay"; + /* Generic PHY, providing serdes lanes */ + phys = <&cp0_comphy2 0>; + }; +}; + +&cp0_usb3_0 { + status = "okay"; + usb-phy = <&cp0_usb3_0_phy0>; + phy-names = "usb"; + phys = <&cp0_comphy1 0>; +}; + +&cp0_usb3_1 { + status = "okay"; + usb-phy = <&cp0_usb3_0_phy1>; + phy-names = "usb"; + phys = <&cp0_comphy3 1>; +}; diff --git a/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi new file mode 100644 index 000000000000..75933477324a --- /dev/null +++ b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi @@ -0,0 +1,222 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2020 Marvell International Ltd. + */ + +#include "cn9130.dtsi" /* include SoC device tree */ + +#include <dt-bindings/gpio/gpio.h> + +/ { + chosen { + stdout-path = "serial0:115200n8"; + }; + + aliases { + i2c0 = &cp0_i2c0; + ethernet0 = &cp0_eth0; + ethernet1 = &cp0_eth1; + ethernet2 = &cp0_eth2; + }; + + memory@00000000 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + ap0_reg_mmc_vccq: ap0_mmc_vccq@0 { + compatible = "regulator-gpio"; + regulator-name = "ap0_mmc_vccq"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + gpios = <&expander0 5 GPIO_ACTIVE_HIGH>; + states = <1800000 0x1 + 3300000 0x0>; + }; + + cp0_reg_usb3_vbus1: cp0_usb3_vbus@1 { + compatible = "regulator-fixed"; + regulator-name = "cp0-xhci1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&expander0 8 GPIO_ACTIVE_HIGH>; + }; + + cp0_usb3_0_phy0: cp0_usb3_phy0 { + compatible = "usb-nop-xceiv"; + }; + + cp0_usb3_0_phy1: cp0_usb3_phy1 { + compatible = "usb-nop-xceiv"; + vcc-supply = <&cp0_reg_usb3_vbus1>; + }; + + cp0_reg_sd_vccq: cp0_sd_vccq@0 { + compatible = "regulator-gpio"; + regulator-name = "cp0_sd_vccq"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + gpios = <&cp0_gpio2 18 GPIO_ACTIVE_HIGH>; + states = <1800000 0x1 + 3300000 0x0>; + }; + + cp0_reg_sd_vcc: cp0_sd_vcc@0 { + compatible = "regulator-fixed"; + regulator-name = "cp0_sd_vcc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&cp0_gpio2 19 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; +}; + +&uart0 { + status = "okay"; +}; + +/* on-board eMMC U6 */ +&ap_sdhci0 { + pinctrl-names = "default"; + bus-width = <8>; + status = "okay"; + mmc-ddr-1_8v; + vqmmc-supply = <&ap0_reg_mmc_vccq>; +}; + +&cp0_syscon0 { + cp0_pinctrl: pinctrl { + compatible = "marvell,cp115-standalone-pinctrl"; + + cp0_i2c0_pins: cp0-i2c-pins-0 { + marvell,pins = "mpp37", "mpp38"; + marvell,function = "i2c0"; + }; + cp0_i2c1_pins: cp0-i2c-pins-1 { + marvell,pins = "mpp35", "mpp36"; + marvell,function = "i2c1"; + }; + cp0_sdhci_cd_pins_crb: cp0-sdhci-cd-pins-crb { + marvell,pins = "mpp55"; + marvell,function = "gpio"; + }; + cp0_sdhci_pins: cp0-sdhi-pins-0 { + marvell,pins = "mpp56", "mpp57", "mpp58", + "mpp59", "mpp60", "mpp61"; + marvell,function = "sdio"; + }; + cp0_spi0_pins: cp0-spi-pins-0 { + marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16"; + marvell,function = "spi1"; + }; + }; +}; + +&cp0_i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&cp0_i2c0_pins>; + status = "okay"; + clock-frequency = <100000>; + expander0: mcp23x17@20 { + compatible = "microchip,mcp23017"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + status = "okay"; + }; +}; + +&cp0_i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&cp0_i2c1_pins>; + clock-frequency = <100000>; + status = "okay"; +}; + + +&cp0_sdhci0 { + pinctrl-names = "default"; + pinctrl-0 = <&cp0_sdhci_pins + &cp0_sdhci_cd_pins_crb>; + bus-width = <4>; + cd-gpios = <&cp0_gpio2 23 GPIO_ACTIVE_HIGH>; + vqmmc-supply = <&cp0_reg_sd_vccq>; + vmmc-supply = <&cp0_reg_sd_vcc>; + status = "okay"; +}; + +&cp0_spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&cp0_spi0_pins>; + reg = <0x700680 0x50>, /* control */ + <0x2000000 0x1000000>; /* CS0 */ + status = "okay"; + + spi-flash@0 { + #address-cells = <0x1>; + #size-cells = <0x1>; + compatible = "jedec,spi-nor"; + reg = <0x0>; + /* On-board MUX does not allow higher frequencies */ + spi-max-frequency = <40000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "U-Boot"; + reg = <0x0 0x200000>; + }; + + partition@400000 { + label = "Filesystem"; + reg = <0x200000 0xe00000>; + }; + }; + }; +}; + +&cp0_mdio { + status = "okay"; + phy0: ethernet-phy@0 { + reg = <0>; + }; +}; + +&cp0_xmdio { + status = "okay"; + nbaset_phy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0>; + }; +}; + +&cp0_ethernet { + status = "okay"; +}; + +&cp0_eth0 { + /* This port is connected to 88E6393X switch */ + status = "okay"; + phy-mode = "10gbase-kr"; + managed = "in-band-status"; + phys = <&cp0_comphy4 0>; +}; + +&cp0_eth1 { + status = "okay"; + phy = <&phy0>; + phy-mode = "rgmii-id"; +}; + +&cp0_eth2 { + /* This port uses "2500base-t" phy-mode */ + status = "disabled"; + phy = <&nbaset_phy0>; + phys = <&cp0_comphy5 2>; +}; + -- 2.17.1 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v4 5/5] arm64: dts: add support for Marvell cn9130-crb platform @ 2021-02-09 13:46 ` kostap 0 siblings, 0 replies; 18+ messages in thread From: kostap @ 2021-02-09 13:46 UTC (permalink / raw) To: linux-kernel, devicetree, linux-arm-kernel Cc: tmn505, andrew, nadavh, jaz, gregory.clement, vkoul, kishon, vladimir.vid, luka.kovacic, robh+dt, miquel.raynal, Konstantin Porotchkin, stefanc, mw, bpeled, sebastian.hesselbarth From: Konstantin Porotchkin <kostap@marvell.com> The Marvell reference platform CN9130-CRB is a small form factor board in a metal case. The platform is based on CN9130 SoC with addition of 8 Gigabit ports SOHO Ethernet switch. The reference platform features the following: * Up to 4 CPU cores ARMv8 Cortex-A72 CPU * CPU core operating speed of up to 2.2GHz * DDR4 DIMM – 8GB 64bit+ECC @ 2400Mhz. * 1x eMMC 8GB device * 1x uSD card 4 bits port on CP * 1x 128MB SPI NOR flash memory * 1x USB 3.0 Host port (Type A) * 1x SATA Gen3 via M.2 * 1x USB 3.0 via M.2 * 1x SIM card slot * 1x 1G Ethernet port via RGMII * 1x 10G switch port over SFP+ connector * 8x 1G ports through 88E6393X switch via XFI * 1x 2.5G/1G/100M/10M port via HS_SGMII * 1x PCI Express (PCIe)x1 Gen 3.0 * 1x PCI Express (PCIe)x4 Gen 3.0 via NVMe M.2 * JTAG port The CRB board uses MCP23017 i2c pin controller that drives the onboard eMMC abd USB 3,0 port power lines. The following configuration should be enabled for this controller support: CONFIG_PINCTRL_MCP23S08=y The plaform supports two HW configurations - "A" and "B" CN9130-CRB-A * AP-MPP configuration: SDIO, UART * CP0 Serdes configuration: * Lane0-3: NVMe (PCIe x4) * Lane4: XFI * Lane5: HS_SGMII 2. CN9130-CRB-B * AP-MPP configuration: SDIO, UART * CP0-MPP configuration: RGMII, SDIO, I2C0, I2C1, SMI, XSMI * CP0 Serdes configuration: * Lane0: PCIe x1 * Lane1: USB3_0 x1 * Lane2: SATA x1 * Lane3: USB3_1 x1 * Lane4: XFI * Lane5: HS_SGMII Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> --- arch/arm64/boot/dts/marvell/Makefile | 2 + arch/arm64/boot/dts/marvell/cn9130-crb-A.dts | 38 ++++ arch/arm64/boot/dts/marvell/cn9130-crb-B.dts | 46 ++++ arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 222 ++++++++++++++++++++ 4 files changed, 308 insertions(+) create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile index 5e39f9774e68..c686a8dd3ca5 100644 --- a/arch/arm64/boot/dts/marvell/Makefile +++ b/arch/arm64/boot/dts/marvell/Makefile @@ -21,3 +21,5 @@ dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db.dtb dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db-B.dtb dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db.dtb dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db-B.dtb +dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-A.dtb +dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-B.dtb diff --git a/arch/arm64/boot/dts/marvell/cn9130-crb-A.dts b/arch/arm64/boot/dts/marvell/cn9130-crb-A.dts new file mode 100644 index 000000000000..a7b6dfba8af5 --- /dev/null +++ b/arch/arm64/boot/dts/marvell/cn9130-crb-A.dts @@ -0,0 +1,38 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2020 Marvell International Ltd. + */ + +#include "cn9130-crb.dtsi" + +/ { + model = "Marvell Armada CN9130-CRB-A"; +}; + +&cp0_pcie0 { + status = "okay"; + num-lanes = <4>; + num-viewport = <8>; + /* Generic PHY, providing serdes lanes */ + phys = <&cp0_comphy0 0 + &cp0_comphy1 0 + &cp0_comphy2 0 + &cp0_comphy3 0>; + iommu-map = + <0x0 &smmu 0x480 0x20>, + <0x100 &smmu 0x4a0 0x20>, + <0x200 &smmu 0x4c0 0x20>; + iommu-map-mask = <0x031f>; +}; + +&cp0_usb3_0 { + status = "okay"; + usb-phy = <&cp0_usb3_0_phy0>; + phy-names = "usb"; +}; + +&cp0_usb3_1 { + status = "okay"; + usb-phy = <&cp0_usb3_0_phy1>; + phy-names = "usb"; +}; diff --git a/arch/arm64/boot/dts/marvell/cn9130-crb-B.dts b/arch/arm64/boot/dts/marvell/cn9130-crb-B.dts new file mode 100644 index 000000000000..0904cb0309ae --- /dev/null +++ b/arch/arm64/boot/dts/marvell/cn9130-crb-B.dts @@ -0,0 +1,46 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2020 Marvell International Ltd. + */ + +#include "cn9130-crb.dtsi" + +/ { + model = "Marvell Armada CN9130-CRB-B"; +}; + +&cp0_pcie0 { + status = "okay"; + num-lanes = <1>; + num-viewport = <8>; + /* Generic PHY, providing serdes lanes */ + phys = <&cp0_comphy0 0>; + iommu-map = + <0x0 &smmu 0x480 0x20>, + <0x100 &smmu 0x4a0 0x20>, + <0x200 &smmu 0x4c0 0x20>; + iommu-map-mask = <0x031f>; +}; + +&cp0_sata0 { + status = "okay"; + sata-port@0 { + status = "okay"; + /* Generic PHY, providing serdes lanes */ + phys = <&cp0_comphy2 0>; + }; +}; + +&cp0_usb3_0 { + status = "okay"; + usb-phy = <&cp0_usb3_0_phy0>; + phy-names = "usb"; + phys = <&cp0_comphy1 0>; +}; + +&cp0_usb3_1 { + status = "okay"; + usb-phy = <&cp0_usb3_0_phy1>; + phy-names = "usb"; + phys = <&cp0_comphy3 1>; +}; diff --git a/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi new file mode 100644 index 000000000000..75933477324a --- /dev/null +++ b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi @@ -0,0 +1,222 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2020 Marvell International Ltd. + */ + +#include "cn9130.dtsi" /* include SoC device tree */ + +#include <dt-bindings/gpio/gpio.h> + +/ { + chosen { + stdout-path = "serial0:115200n8"; + }; + + aliases { + i2c0 = &cp0_i2c0; + ethernet0 = &cp0_eth0; + ethernet1 = &cp0_eth1; + ethernet2 = &cp0_eth2; + }; + + memory@00000000 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + ap0_reg_mmc_vccq: ap0_mmc_vccq@0 { + compatible = "regulator-gpio"; + regulator-name = "ap0_mmc_vccq"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + gpios = <&expander0 5 GPIO_ACTIVE_HIGH>; + states = <1800000 0x1 + 3300000 0x0>; + }; + + cp0_reg_usb3_vbus1: cp0_usb3_vbus@1 { + compatible = "regulator-fixed"; + regulator-name = "cp0-xhci1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&expander0 8 GPIO_ACTIVE_HIGH>; + }; + + cp0_usb3_0_phy0: cp0_usb3_phy0 { + compatible = "usb-nop-xceiv"; + }; + + cp0_usb3_0_phy1: cp0_usb3_phy1 { + compatible = "usb-nop-xceiv"; + vcc-supply = <&cp0_reg_usb3_vbus1>; + }; + + cp0_reg_sd_vccq: cp0_sd_vccq@0 { + compatible = "regulator-gpio"; + regulator-name = "cp0_sd_vccq"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + gpios = <&cp0_gpio2 18 GPIO_ACTIVE_HIGH>; + states = <1800000 0x1 + 3300000 0x0>; + }; + + cp0_reg_sd_vcc: cp0_sd_vcc@0 { + compatible = "regulator-fixed"; + regulator-name = "cp0_sd_vcc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&cp0_gpio2 19 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; +}; + +&uart0 { + status = "okay"; +}; + +/* on-board eMMC U6 */ +&ap_sdhci0 { + pinctrl-names = "default"; + bus-width = <8>; + status = "okay"; + mmc-ddr-1_8v; + vqmmc-supply = <&ap0_reg_mmc_vccq>; +}; + +&cp0_syscon0 { + cp0_pinctrl: pinctrl { + compatible = "marvell,cp115-standalone-pinctrl"; + + cp0_i2c0_pins: cp0-i2c-pins-0 { + marvell,pins = "mpp37", "mpp38"; + marvell,function = "i2c0"; + }; + cp0_i2c1_pins: cp0-i2c-pins-1 { + marvell,pins = "mpp35", "mpp36"; + marvell,function = "i2c1"; + }; + cp0_sdhci_cd_pins_crb: cp0-sdhci-cd-pins-crb { + marvell,pins = "mpp55"; + marvell,function = "gpio"; + }; + cp0_sdhci_pins: cp0-sdhi-pins-0 { + marvell,pins = "mpp56", "mpp57", "mpp58", + "mpp59", "mpp60", "mpp61"; + marvell,function = "sdio"; + }; + cp0_spi0_pins: cp0-spi-pins-0 { + marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16"; + marvell,function = "spi1"; + }; + }; +}; + +&cp0_i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&cp0_i2c0_pins>; + status = "okay"; + clock-frequency = <100000>; + expander0: mcp23x17@20 { + compatible = "microchip,mcp23017"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + status = "okay"; + }; +}; + +&cp0_i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&cp0_i2c1_pins>; + clock-frequency = <100000>; + status = "okay"; +}; + + +&cp0_sdhci0 { + pinctrl-names = "default"; + pinctrl-0 = <&cp0_sdhci_pins + &cp0_sdhci_cd_pins_crb>; + bus-width = <4>; + cd-gpios = <&cp0_gpio2 23 GPIO_ACTIVE_HIGH>; + vqmmc-supply = <&cp0_reg_sd_vccq>; + vmmc-supply = <&cp0_reg_sd_vcc>; + status = "okay"; +}; + +&cp0_spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&cp0_spi0_pins>; + reg = <0x700680 0x50>, /* control */ + <0x2000000 0x1000000>; /* CS0 */ + status = "okay"; + + spi-flash@0 { + #address-cells = <0x1>; + #size-cells = <0x1>; + compatible = "jedec,spi-nor"; + reg = <0x0>; + /* On-board MUX does not allow higher frequencies */ + spi-max-frequency = <40000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "U-Boot"; + reg = <0x0 0x200000>; + }; + + partition@400000 { + label = "Filesystem"; + reg = <0x200000 0xe00000>; + }; + }; + }; +}; + +&cp0_mdio { + status = "okay"; + phy0: ethernet-phy@0 { + reg = <0>; + }; +}; + +&cp0_xmdio { + status = "okay"; + nbaset_phy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0>; + }; +}; + +&cp0_ethernet { + status = "okay"; +}; + +&cp0_eth0 { + /* This port is connected to 88E6393X switch */ + status = "okay"; + phy-mode = "10gbase-kr"; + managed = "in-band-status"; + phys = <&cp0_comphy4 0>; +}; + +&cp0_eth1 { + status = "okay"; + phy = <&phy0>; + phy-mode = "rgmii-id"; +}; + +&cp0_eth2 { + /* This port uses "2500base-t" phy-mode */ + status = "disabled"; + phy = <&nbaset_phy0>; + phys = <&cp0_comphy5 2>; +}; + -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 18+ messages in thread
* Re: [PATCH v4 0/5] DTS updates for Marvell Armada CN913x platforms 2021-02-09 13:46 ` kostap @ 2021-06-17 15:40 ` Gregory CLEMENT -1 siblings, 0 replies; 18+ messages in thread From: Gregory CLEMENT @ 2021-06-17 15:40 UTC (permalink / raw) To: kostap, linux-kernel, devicetree, linux-arm-kernel Cc: vladimir.vid, tmn505, luka.kovacic, sebastian.hesselbarth, andrew, robh+dt, vkoul, kishon, miquel.raynal, mw, jaz, nadavh, stefanc, bpeled, Konstantin Porotchkin Hello, > From: Konstantin Porotchkin <kostap@marvell.com> > > This patch series contains the following changes/fixes: > 1. Add support for Armada CN913x Development Board topology "B" > 2. Add support for Armada CN913x Reference Design boards (CRB) > 3. Fixes the CP11X references in PHY binding document > 4. Fixes the NAND paritioninig scheme in DTS eliminating gap between > consecutive partitions > All above changes are already intergated into Marvell official SDK sources > > v2: > - extract common nodes from DB boards to separate DTSI files > - disable eth2 on CRB boards until the required phy mode support is added > - mention the switch part ID in CRB board description > > v3: > - do not rename setup A DTS files for DB variants > - fix a couple of wrong include names > > v4: > - Rebase on top of Linus master branch (v5.11-rc7) > - Remove HS400 timing from CRB AP SDHCI (not supported by connected eMMC) > - Add cd-gpio entry to CP0 SDHCI for SD card support > - Add a comment to CN9130-CRB patch about the required defconfig > changes for supporting the onboard i2c expander > - Add Stefan's patch to enable 10G port on CN9130-DB platforms > > Grzegorz Jaszczyk (1): > Documentation/bindings: phy: update references to cp11x > > Konstantin Porotchkin (3): > arch/arm64/boot/dts/marvell: fix NAND partitioning scheme > arm64: dts: cn913x: add device trees for topology B boards > arm64: dts: add support for Marvell cn9130-crb platform > > Stefan Chulski (1): > dts: marvell: Enable 10G interface on 9130-DB board > I've applied patches 1 and 2, but I have issue with patch 3, there was some changes around the phys and I am not sure of the correct way to modify the patch. Could you rebase it on v5.13-c1 and fix the merge issue ? Thanks, Gregory > .../bindings/phy/phy-mvebu-comphy.txt | 12 +- > arch/arm64/boot/dts/marvell/Makefile | 5 + > arch/arm64/boot/dts/marvell/cn9130-crb-A.dts | 38 ++ > arch/arm64/boot/dts/marvell/cn9130-crb-B.dts | 46 ++ > arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 221 ++++++++++ > arch/arm64/boot/dts/marvell/cn9130-db-B.dts | 22 + > arch/arm64/boot/dts/marvell/cn9130-db.dts | 393 +---------------- > arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 402 ++++++++++++++++++ > arch/arm64/boot/dts/marvell/cn9131-db-B.dts | 22 + > arch/arm64/boot/dts/marvell/cn9131-db.dts | 192 +-------- > arch/arm64/boot/dts/marvell/cn9131-db.dtsi | 201 +++++++++ > arch/arm64/boot/dts/marvell/cn9132-db-B.dts | 22 + > arch/arm64/boot/dts/marvell/cn9132-db.dts | 211 +-------- > arch/arm64/boot/dts/marvell/cn9132-db.dtsi | 220 ++++++++++ > 14 files changed, 1223 insertions(+), 784 deletions(-) > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db-B.dts > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dtsi > create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db-B.dts > create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dtsi > create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db-B.dts > create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dtsi > > -- > 2.17.1 > -- Gregory Clement, Bootlin Embedded Linux and Kernel engineering http://bootlin.com ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v4 0/5] DTS updates for Marvell Armada CN913x platforms @ 2021-06-17 15:40 ` Gregory CLEMENT 0 siblings, 0 replies; 18+ messages in thread From: Gregory CLEMENT @ 2021-06-17 15:40 UTC (permalink / raw) To: kostap, linux-kernel, devicetree, linux-arm-kernel Cc: vladimir.vid, tmn505, luka.kovacic, sebastian.hesselbarth, andrew, robh+dt, vkoul, kishon, miquel.raynal, mw, jaz, nadavh, stefanc, bpeled, Konstantin Porotchkin Hello, > From: Konstantin Porotchkin <kostap@marvell.com> > > This patch series contains the following changes/fixes: > 1. Add support for Armada CN913x Development Board topology "B" > 2. Add support for Armada CN913x Reference Design boards (CRB) > 3. Fixes the CP11X references in PHY binding document > 4. Fixes the NAND paritioninig scheme in DTS eliminating gap between > consecutive partitions > All above changes are already intergated into Marvell official SDK sources > > v2: > - extract common nodes from DB boards to separate DTSI files > - disable eth2 on CRB boards until the required phy mode support is added > - mention the switch part ID in CRB board description > > v3: > - do not rename setup A DTS files for DB variants > - fix a couple of wrong include names > > v4: > - Rebase on top of Linus master branch (v5.11-rc7) > - Remove HS400 timing from CRB AP SDHCI (not supported by connected eMMC) > - Add cd-gpio entry to CP0 SDHCI for SD card support > - Add a comment to CN9130-CRB patch about the required defconfig > changes for supporting the onboard i2c expander > - Add Stefan's patch to enable 10G port on CN9130-DB platforms > > Grzegorz Jaszczyk (1): > Documentation/bindings: phy: update references to cp11x > > Konstantin Porotchkin (3): > arch/arm64/boot/dts/marvell: fix NAND partitioning scheme > arm64: dts: cn913x: add device trees for topology B boards > arm64: dts: add support for Marvell cn9130-crb platform > > Stefan Chulski (1): > dts: marvell: Enable 10G interface on 9130-DB board > I've applied patches 1 and 2, but I have issue with patch 3, there was some changes around the phys and I am not sure of the correct way to modify the patch. Could you rebase it on v5.13-c1 and fix the merge issue ? Thanks, Gregory > .../bindings/phy/phy-mvebu-comphy.txt | 12 +- > arch/arm64/boot/dts/marvell/Makefile | 5 + > arch/arm64/boot/dts/marvell/cn9130-crb-A.dts | 38 ++ > arch/arm64/boot/dts/marvell/cn9130-crb-B.dts | 46 ++ > arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 221 ++++++++++ > arch/arm64/boot/dts/marvell/cn9130-db-B.dts | 22 + > arch/arm64/boot/dts/marvell/cn9130-db.dts | 393 +---------------- > arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 402 ++++++++++++++++++ > arch/arm64/boot/dts/marvell/cn9131-db-B.dts | 22 + > arch/arm64/boot/dts/marvell/cn9131-db.dts | 192 +-------- > arch/arm64/boot/dts/marvell/cn9131-db.dtsi | 201 +++++++++ > arch/arm64/boot/dts/marvell/cn9132-db-B.dts | 22 + > arch/arm64/boot/dts/marvell/cn9132-db.dts | 211 +-------- > arch/arm64/boot/dts/marvell/cn9132-db.dtsi | 220 ++++++++++ > 14 files changed, 1223 insertions(+), 784 deletions(-) > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db-B.dts > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dtsi > create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db-B.dts > create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dtsi > create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db-B.dts > create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dtsi > > -- > 2.17.1 > -- Gregory Clement, Bootlin Embedded Linux and Kernel engineering http://bootlin.com _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 18+ messages in thread
* RE: [EXT] Re: [PATCH v4 0/5] DTS updates for Marvell Armada CN913x platforms 2021-06-17 15:40 ` Gregory CLEMENT @ 2021-07-08 7:50 ` Kostya Porotchkin -1 siblings, 0 replies; 18+ messages in thread From: Kostya Porotchkin @ 2021-07-08 7:50 UTC (permalink / raw) To: Gregory CLEMENT, linux-kernel, devicetree, linux-arm-kernel Cc: vladimir.vid, tmn505, luka.kovacic, sebastian.hesselbarth, andrew, robh+dt, vkoul, kishon, miquel.raynal, mw, jaz, Nadav Haklai, Stefan Chulski, Ben Peled Hi, Gregory, The last series was v5. I will rebase on top of Linus 5.13-rcx and then post new v6 set. Regards Kosta > -----Original Message----- > From: Gregory CLEMENT <gregory.clement@bootlin.com> > Sent: Thursday, June 17, 2021 18:40 > To: Kostya Porotchkin <kostap@marvell.com>; linux-kernel@vger.kernel.org; > devicetree@vger.kernel.org; linux-arm-kernel@lists.infradead.org > Cc: vladimir.vid@sartura.hr; tmn505@gmail.com; luka.kovacic@sartura.hr; > sebastian.hesselbarth@gmail.com; andrew@lunn.ch; robh+dt@kernel.org; > vkoul@kernel.org; kishon@ti.com; miquel.raynal@bootlin.com; > mw@semihalf.com; jaz@semihalf.com; Nadav Haklai > <nadavh@marvell.com>; Stefan Chulski <stefanc@marvell.com>; Ben Peled > <bpeled@marvell.com>; Kostya Porotchkin <kostap@marvell.com> > Subject: [EXT] Re: [PATCH v4 0/5] DTS updates for Marvell Armada CN913x > platforms > > External Email > > ---------------------------------------------------------------------- > Hello, > > > From: Konstantin Porotchkin <kostap@marvell.com> > > > > This patch series contains the following changes/fixes: > > 1. Add support for Armada CN913x Development Board topology "B" > > 2. Add support for Armada CN913x Reference Design boards (CRB) 3. > > Fixes the CP11X references in PHY binding document 4. Fixes the NAND > > paritioninig scheme in DTS eliminating gap between consecutive > > partitions All above changes are already intergated into Marvell > > official SDK sources > > > > v2: > > - extract common nodes from DB boards to separate DTSI files > > - disable eth2 on CRB boards until the required phy mode support is > > added > > - mention the switch part ID in CRB board description > > > > v3: > > - do not rename setup A DTS files for DB variants > > - fix a couple of wrong include names > > > > v4: > > - Rebase on top of Linus master branch (v5.11-rc7) > > - Remove HS400 timing from CRB AP SDHCI (not supported by connected > > eMMC) > > - Add cd-gpio entry to CP0 SDHCI for SD card support > > - Add a comment to CN9130-CRB patch about the required defconfig > > changes for supporting the onboard i2c expander > > - Add Stefan's patch to enable 10G port on CN9130-DB platforms > > > > Grzegorz Jaszczyk (1): > > Documentation/bindings: phy: update references to cp11x > > > > Konstantin Porotchkin (3): > > arch/arm64/boot/dts/marvell: fix NAND partitioning scheme > > arm64: dts: cn913x: add device trees for topology B boards > > arm64: dts: add support for Marvell cn9130-crb platform > > > > Stefan Chulski (1): > > dts: marvell: Enable 10G interface on 9130-DB board > > > > I've applied patches 1 and 2, but I have issue with patch 3, there was some > changes around the phys and I am not sure of the correct way to modify the > patch. > > Could you rebase it on v5.13-c1 and fix the merge issue ? > > Thanks, > > Gregory > > > .../bindings/phy/phy-mvebu-comphy.txt | 12 +- > > arch/arm64/boot/dts/marvell/Makefile | 5 + > > arch/arm64/boot/dts/marvell/cn9130-crb-A.dts | 38 ++ > > arch/arm64/boot/dts/marvell/cn9130-crb-B.dts | 46 ++ > > arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 221 ++++++++++ > > arch/arm64/boot/dts/marvell/cn9130-db-B.dts | 22 + > > arch/arm64/boot/dts/marvell/cn9130-db.dts | 393 +---------------- > > arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 402 ++++++++++++++++++ > > arch/arm64/boot/dts/marvell/cn9131-db-B.dts | 22 + > > arch/arm64/boot/dts/marvell/cn9131-db.dts | 192 +-------- > > arch/arm64/boot/dts/marvell/cn9131-db.dtsi | 201 +++++++++ > > arch/arm64/boot/dts/marvell/cn9132-db-B.dts | 22 + > > arch/arm64/boot/dts/marvell/cn9132-db.dts | 211 +-------- > > arch/arm64/boot/dts/marvell/cn9132-db.dtsi | 220 ++++++++++ > > 14 files changed, 1223 insertions(+), 784 deletions(-) create mode > > 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts > > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts > > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi > > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db-B.dts > > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dtsi > > create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db-B.dts > > create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dtsi > > create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db-B.dts > > create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dtsi > > > > -- > > 2.17.1 > > > > -- > Gregory Clement, Bootlin > Embedded Linux and Kernel engineering > https://urldefense.proofpoint.com/v2/url?u=http- > 3A__bootlin.com&d=DwIBAg&c=nKjWec2b6R0mOyPaz7xtfQ&r=- > N9sN4p5NSr0JGQoQ_2UCOgAqajG99W1EbSOww0WU8o&m=yb2JOcVicfAZRe > thZJoDE- > wbwtupb3tk_D7VGKCNsqc&s=4oskkLywYJujfGQ4XpFfP6n4ybkC0722K_8qH3xz > bK8&e= ^ permalink raw reply [flat|nested] 18+ messages in thread
* RE: [EXT] Re: [PATCH v4 0/5] DTS updates for Marvell Armada CN913x platforms @ 2021-07-08 7:50 ` Kostya Porotchkin 0 siblings, 0 replies; 18+ messages in thread From: Kostya Porotchkin @ 2021-07-08 7:50 UTC (permalink / raw) To: Gregory CLEMENT, linux-kernel, devicetree, linux-arm-kernel Cc: vladimir.vid, tmn505, luka.kovacic, sebastian.hesselbarth, andrew, robh+dt, vkoul, kishon, miquel.raynal, mw, jaz, Nadav Haklai, Stefan Chulski, Ben Peled Hi, Gregory, The last series was v5. I will rebase on top of Linus 5.13-rcx and then post new v6 set. Regards Kosta > -----Original Message----- > From: Gregory CLEMENT <gregory.clement@bootlin.com> > Sent: Thursday, June 17, 2021 18:40 > To: Kostya Porotchkin <kostap@marvell.com>; linux-kernel@vger.kernel.org; > devicetree@vger.kernel.org; linux-arm-kernel@lists.infradead.org > Cc: vladimir.vid@sartura.hr; tmn505@gmail.com; luka.kovacic@sartura.hr; > sebastian.hesselbarth@gmail.com; andrew@lunn.ch; robh+dt@kernel.org; > vkoul@kernel.org; kishon@ti.com; miquel.raynal@bootlin.com; > mw@semihalf.com; jaz@semihalf.com; Nadav Haklai > <nadavh@marvell.com>; Stefan Chulski <stefanc@marvell.com>; Ben Peled > <bpeled@marvell.com>; Kostya Porotchkin <kostap@marvell.com> > Subject: [EXT] Re: [PATCH v4 0/5] DTS updates for Marvell Armada CN913x > platforms > > External Email > > ---------------------------------------------------------------------- > Hello, > > > From: Konstantin Porotchkin <kostap@marvell.com> > > > > This patch series contains the following changes/fixes: > > 1. Add support for Armada CN913x Development Board topology "B" > > 2. Add support for Armada CN913x Reference Design boards (CRB) 3. > > Fixes the CP11X references in PHY binding document 4. Fixes the NAND > > paritioninig scheme in DTS eliminating gap between consecutive > > partitions All above changes are already intergated into Marvell > > official SDK sources > > > > v2: > > - extract common nodes from DB boards to separate DTSI files > > - disable eth2 on CRB boards until the required phy mode support is > > added > > - mention the switch part ID in CRB board description > > > > v3: > > - do not rename setup A DTS files for DB variants > > - fix a couple of wrong include names > > > > v4: > > - Rebase on top of Linus master branch (v5.11-rc7) > > - Remove HS400 timing from CRB AP SDHCI (not supported by connected > > eMMC) > > - Add cd-gpio entry to CP0 SDHCI for SD card support > > - Add a comment to CN9130-CRB patch about the required defconfig > > changes for supporting the onboard i2c expander > > - Add Stefan's patch to enable 10G port on CN9130-DB platforms > > > > Grzegorz Jaszczyk (1): > > Documentation/bindings: phy: update references to cp11x > > > > Konstantin Porotchkin (3): > > arch/arm64/boot/dts/marvell: fix NAND partitioning scheme > > arm64: dts: cn913x: add device trees for topology B boards > > arm64: dts: add support for Marvell cn9130-crb platform > > > > Stefan Chulski (1): > > dts: marvell: Enable 10G interface on 9130-DB board > > > > I've applied patches 1 and 2, but I have issue with patch 3, there was some > changes around the phys and I am not sure of the correct way to modify the > patch. > > Could you rebase it on v5.13-c1 and fix the merge issue ? > > Thanks, > > Gregory > > > .../bindings/phy/phy-mvebu-comphy.txt | 12 +- > > arch/arm64/boot/dts/marvell/Makefile | 5 + > > arch/arm64/boot/dts/marvell/cn9130-crb-A.dts | 38 ++ > > arch/arm64/boot/dts/marvell/cn9130-crb-B.dts | 46 ++ > > arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 221 ++++++++++ > > arch/arm64/boot/dts/marvell/cn9130-db-B.dts | 22 + > > arch/arm64/boot/dts/marvell/cn9130-db.dts | 393 +---------------- > > arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 402 ++++++++++++++++++ > > arch/arm64/boot/dts/marvell/cn9131-db-B.dts | 22 + > > arch/arm64/boot/dts/marvell/cn9131-db.dts | 192 +-------- > > arch/arm64/boot/dts/marvell/cn9131-db.dtsi | 201 +++++++++ > > arch/arm64/boot/dts/marvell/cn9132-db-B.dts | 22 + > > arch/arm64/boot/dts/marvell/cn9132-db.dts | 211 +-------- > > arch/arm64/boot/dts/marvell/cn9132-db.dtsi | 220 ++++++++++ > > 14 files changed, 1223 insertions(+), 784 deletions(-) create mode > > 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts > > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts > > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi > > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db-B.dts > > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dtsi > > create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db-B.dts > > create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dtsi > > create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db-B.dts > > create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dtsi > > > > -- > > 2.17.1 > > > > -- > Gregory Clement, Bootlin > Embedded Linux and Kernel engineering > https://urldefense.proofpoint.com/v2/url?u=http- > 3A__bootlin.com&d=DwIBAg&c=nKjWec2b6R0mOyPaz7xtfQ&r=- > N9sN4p5NSr0JGQoQ_2UCOgAqajG99W1EbSOww0WU8o&m=yb2JOcVicfAZRe > thZJoDE- > wbwtupb3tk_D7VGKCNsqc&s=4oskkLywYJujfGQ4XpFfP6n4ybkC0722K_8qH3xz > bK8&e= _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 18+ messages in thread
end of thread, other threads:[~2021-07-08 7:52 UTC | newest] Thread overview: 18+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2021-02-09 13:46 [PATCH v4 0/5] DTS updates for Marvell Armada CN913x platforms kostap 2021-02-09 13:46 ` kostap 2021-02-09 13:46 ` [PATCH v4 1/5] Documentation/bindings: phy: update references to cp11x kostap 2021-02-09 13:46 ` kostap 2021-02-09 13:46 ` [PATCH v4 2/5] arch/arm64/boot/dts/marvell: fix NAND partitioning scheme kostap 2021-02-09 13:46 ` kostap 2021-02-09 13:46 ` [PATCH v4 3/5] arm64: dts: cn913x: add device trees for topology B boards kostap 2021-02-09 13:46 ` kostap 2021-02-09 13:46 ` [PATCH v4 4/5] dts: marvell: Enable 10G interface on 9130-DB board kostap 2021-02-09 13:46 ` kostap 2021-02-09 14:13 ` Marcin Wojtas 2021-02-09 14:13 ` Marcin Wojtas 2021-02-09 13:46 ` [PATCH v4 5/5] arm64: dts: add support for Marvell cn9130-crb platform kostap 2021-02-09 13:46 ` kostap 2021-06-17 15:40 ` [PATCH v4 0/5] DTS updates for Marvell Armada CN913x platforms Gregory CLEMENT 2021-06-17 15:40 ` Gregory CLEMENT 2021-07-08 7:50 ` [EXT] " Kostya Porotchkin 2021-07-08 7:50 ` Kostya Porotchkin
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.