[PATCH 16/27] ppc: Remove MPC8555CDS boards

[Tom Rini <trini@konsulko.com>]

These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM.  Remove them.  As this is the only
ARCH_MPC8555 platform left, remove that support as well.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
---
 arch/powerpc/cpu/mpc85xx/Kconfig        |  18 +-
 arch/powerpc/cpu/mpc85xx/cpu.c          |   3 +-
 arch/powerpc/cpu/mpc85xx/pci.c          |  23 --
 arch/powerpc/cpu/mpc85xx/speed.c        |   3 +-
 arch/powerpc/include/asm/cpm_85xx.h     |   5 -
 arch/powerpc/include/asm/fsl_lbc.h      |   2 +-
 arch/powerpc/include/asm/immap_85xx.h   |   3 +-
 board/freescale/common/Makefile         |   1 -
 board/freescale/mpc8555cds/Kconfig      |  12 -
 board/freescale/mpc8555cds/MAINTAINERS  |   7 -
 board/freescale/mpc8555cds/Makefile     |  10 -
 board/freescale/mpc8555cds/ddr.c        |  53 ---
 board/freescale/mpc8555cds/law.c        |  41 ---
 board/freescale/mpc8555cds/mpc8555cds.c | 430 ------------------------
 board/freescale/mpc8555cds/tlb.c        |  95 ------
 configs/MPC8555CDS_defconfig            |  40 ---
 configs/MPC8555CDS_legacy_defconfig     |  41 ---
 drivers/ddr/fsl/ctrl_regs.c             |  20 +-
 drivers/ddr/fsl/mpc85xx_ddr_gen1.c      |   3 -
 include/configs/MPC8555CDS.h            | 380 ---------------------
 20 files changed, 9 insertions(+), 1181 deletions(-)
 delete mode 100644 board/freescale/mpc8555cds/Kconfig
 delete mode 100644 board/freescale/mpc8555cds/MAINTAINERS
 delete mode 100644 board/freescale/mpc8555cds/Makefile
 delete mode 100644 board/freescale/mpc8555cds/ddr.c
 delete mode 100644 board/freescale/mpc8555cds/law.c
 delete mode 100644 board/freescale/mpc8555cds/mpc8555cds.c
 delete mode 100644 board/freescale/mpc8555cds/tlb.c
 delete mode 100644 configs/MPC8555CDS_defconfig
 delete mode 100644 configs/MPC8555CDS_legacy_defconfig
 delete mode 100644 include/configs/MPC8555CDS.h

diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig
index 0b1385695283..891db4e37810 100644
--- a/arch/powerpc/cpu/mpc85xx/Kconfig
+++ b/arch/powerpc/cpu/mpc85xx/Kconfig
@@ -49,11 +49,6 @@ config TARGET_MPC8548CDS
 	select ARCH_MPC8548
 	select FSL_VIA
 
-config TARGET_MPC8555CDS
-	bool "Support MPC8555CDS"
-	select ARCH_MPC8555
-	select FSL_VIA
-
 config TARGET_MPC8568MDS
 	bool "Support MPC8568MDS"
 	select ARCH_MPC8568
@@ -388,14 +383,6 @@ config ARCH_MPC8548
 	select SYS_PPC_E500_USE_DEBUG_TLB
 	imply CMD_REGINFO
 
-config ARCH_MPC8555
-	bool
-	select FSL_LAW
-	select SYS_FSL_HAS_DDR1
-	select SYS_FSL_HAS_SEC
-	select SYS_FSL_SEC_BE
-	select SYS_FSL_SEC_COMPAT_2
-
 config ARCH_MPC8560
 	bool
 	select FSL_LAW
@@ -948,7 +935,6 @@ config SYS_CCSRBAR_DEFAULT
 				ARCH_MPC8540	|| \
 				ARCH_MPC8544	|| \
 				ARCH_MPC8548	|| \
-				ARCH_MPC8555	|| \
 				ARCH_MPC8560	|| \
 				ARCH_MPC8568	|| \
 				ARCH_MPC8572	|| \
@@ -1179,7 +1165,6 @@ config SYS_FSL_NUM_LAWS
 			ARCH_MPC8548	|| \
 			ARCH_MPC8568
 	default 8 if	ARCH_MPC8540	|| \
-			ARCH_MPC8555	|| \
 			ARCH_MPC8560
 	help
 		Number of local access windows. This is fixed per SoC.
@@ -1253,7 +1238,7 @@ config SYS_FSL_LBC_CLK_DIV
 	int "Divider of platform clock"
 	depends on FSL_ELBC || ARCH_MPC8540 || \
 		ARCH_MPC8548 || \
-		ARCH_MPC8555 || ARCH_MPC8560 || \
+		ARCH_MPC8560 || \
 		ARCH_MPC8568
 
 	default 2 if	ARCH_P2041	|| \
@@ -1272,7 +1257,6 @@ config FSL_VIA
 source "board/emulation/qemu-ppce500/Kconfig"
 source "board/freescale/corenet_ds/Kconfig"
 source "board/freescale/mpc8548cds/Kconfig"
-source "board/freescale/mpc8555cds/Kconfig"
 source "board/freescale/mpc8568mds/Kconfig"
 source "board/freescale/p1010rdb/Kconfig"
 source "board/freescale/p1_p2_rdb_pc/Kconfig"
diff --git a/arch/powerpc/cpu/mpc85xx/cpu.c b/arch/powerpc/cpu/mpc85xx/cpu.c
index e8126c98f898..610a8ec43f5b 100644
--- a/arch/powerpc/cpu/mpc85xx/cpu.c
+++ b/arch/powerpc/cpu/mpc85xx/cpu.c
@@ -301,8 +301,7 @@ int checkcpu (void)
 int do_reset(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[])
 {
 /* Everything after the first generation of PQ3 parts has RSTCR */
-#if defined(CONFIG_ARCH_MPC8540) || defined(CONFIG_ARCH_MPC8555) || \
-	defined(CONFIG_ARCH_MPC8560)
+#if defined(CONFIG_ARCH_MPC8540) || defined(CONFIG_ARCH_MPC8560)
 	unsigned long val, msr;
 
 	/*
diff --git a/arch/powerpc/cpu/mpc85xx/pci.c b/arch/powerpc/cpu/mpc85xx/pci.c
index 559730181ef1..b7835c0fee54 100644
--- a/arch/powerpc/cpu/mpc85xx/pci.c
+++ b/arch/powerpc/cpu/mpc85xx/pci.c
@@ -120,29 +120,6 @@ pci_mpc85xx_init(struct pci_controller *board_hose)
 
 	pci_register_hose(hose);
 
-#if defined(CONFIG_TARGET_MPC8555CDS)
-	/*
-	 * This is a SW workaround for an apparent HW problem
-	 * in the PCI controller on the MPC85555/41 CDS boards.
-	 * The first config cycle must be to a valid, known
-	 * device on the PCI bus in order to trick the PCI
-	 * controller state machine into a known valid state.
-	 * Without this, the first config cycle has the chance
-	 * of hanging the controller permanently, just leaving
-	 * it in a semi-working state, or leaving it working.
-	 *
-	 * Pick on the Tundra, Device 17, to get it right.
-	 */
-	{
-		u8 header_type;
-
-		pci_hose_read_config_byte(hose,
-					  PCI_BDF(0,BRIDGE_ID,0),
-					  PCI_HEADER_TYPE,
-					  &header_type);
-	}
-#endif
-
 	hose->last_busno = pci_hose_scan(hose);
 
 #ifdef CONFIG_MPC85XX_PCI2
diff --git a/arch/powerpc/cpu/mpc85xx/speed.c b/arch/powerpc/cpu/mpc85xx/speed.c
index 90c9fe1af51b..26067dd7132c 100644
--- a/arch/powerpc/cpu/mpc85xx/speed.c
+++ b/arch/powerpc/cpu/mpc85xx/speed.c
@@ -607,8 +607,7 @@ int get_clocks(void)
 	 * for that SOC. This information is taken from application note
 	 * AN2919.
 	 */
-#if defined(CONFIG_ARCH_MPC8540) || defined(CONFIG_ARCH_MPC8560) || \
-	defined(CONFIG_ARCH_MPC8555)
+#if defined(CONFIG_ARCH_MPC8540) || defined(CONFIG_ARCH_MPC8560)
 	gd->arch.i2c1_clk = sys_info.freq_systembus;
 #elif defined(CONFIG_ARCH_MPC8544)
 	/*
diff --git a/arch/powerpc/include/asm/cpm_85xx.h b/arch/powerpc/include/asm/cpm_85xx.h
index e6f1fab5fb95..d42469c6e056 100644
--- a/arch/powerpc/include/asm/cpm_85xx.h
+++ b/arch/powerpc/include/asm/cpm_85xx.h
@@ -77,13 +77,8 @@
  */
 #define CPM_DATAONLY_BASE	((uint)128)
 #define CPM_DP_NOSPACE		((uint)0x7FFFFFFF)
-#if defined(CONFIG_ARCH_MPC8555)
-#define CPM_FCC_SPECIAL_BASE	((uint)0x00009000)
-#define CPM_DATAONLY_SIZE	((uint)(8 * 1024) - CPM_DATAONLY_BASE)
-#else	/* MPC8540, MPC8560 */
 #define CPM_FCC_SPECIAL_BASE	((uint)0x0000B000)
 #define CPM_DATAONLY_SIZE	((uint)(16 * 1024) - CPM_DATAONLY_BASE)
-#endif
 
 /* The number of pages of host memory we allocate for CPM.  This is
  * done early in kernel initialization to get physically contiguous
diff --git a/arch/powerpc/include/asm/fsl_lbc.h b/arch/powerpc/include/asm/fsl_lbc.h
index ae176082760f..3b26451928a0 100644
--- a/arch/powerpc/include/asm/fsl_lbc.h
+++ b/arch/powerpc/include/asm/fsl_lbc.h
@@ -325,7 +325,7 @@ void lbc_sdram_init(void);
 #define LCRR_CLKDIV			0x0000001F
 #define LCRR_CLKDIV_SHIFT		0
 #if defined(CONFIG_MPC83xx) || defined(CONFIG_ARCH_MPC8540) || \
-	defined(CONFIG_ARCH_MPC8555) || defined(CONFIG_ARCH_MPC8560)
+	defined(CONFIG_ARCH_MPC8560)
 #define LCRR_CLKDIV_2			0x00000002
 #define LCRR_CLKDIV_4			0x00000004
 #define LCRR_CLKDIV_8			0x00000008
diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h
index b6770c4cf4d3..1411b3f38b94 100644
--- a/arch/powerpc/include/asm/immap_85xx.h
+++ b/arch/powerpc/include/asm/immap_85xx.h
@@ -124,8 +124,7 @@ typedef struct ccsr_i2c {
 } ccsr_i2c_t;
 
 #if defined(CONFIG_ARCH_MPC8540) || \
-	defined(CONFIG_ARCH_MPC8548) || \
-	defined(CONFIG_ARCH_MPC8555)
+	defined(CONFIG_ARCH_MPC8548)
 /* DUART Registers */
 typedef struct ccsr_duart {
 	u8	res1[1280];
diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile
index 5d18567332fe..7862a791ac54 100644
--- a/board/freescale/common/Makefile
+++ b/board/freescale/common/Makefile
@@ -44,7 +44,6 @@ endif
 obj-$(CONFIG_FSL_DCU_SII9022A)    += dcu_sii9022a.o
 
 obj-$(CONFIG_TARGET_MPC8548CDS)	+= cds_pci_ft.o
-obj-$(CONFIG_TARGET_MPC8555CDS)	+= cds_pci_ft.o
 
 obj-$(CONFIG_TARGET_MPC8536DS)	+= ics307_clk.o
 obj-$(CONFIG_TARGET_P1022DS)		+= ics307_clk.o
diff --git a/board/freescale/mpc8555cds/Kconfig b/board/freescale/mpc8555cds/Kconfig
deleted file mode 100644
index 04bd572212a0..000000000000
--- a/board/freescale/mpc8555cds/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_MPC8555CDS
-
-config SYS_BOARD
-	default "mpc8555cds"
-
-config SYS_VENDOR
-	default "freescale"
-
-config SYS_CONFIG_NAME
-	default "MPC8555CDS"
-
-endif
diff --git a/board/freescale/mpc8555cds/MAINTAINERS b/board/freescale/mpc8555cds/MAINTAINERS
deleted file mode 100644
index 8f32febd9147..000000000000
--- a/board/freescale/mpc8555cds/MAINTAINERS
+++ /dev/null
@@ -1,7 +0,0 @@
-MPC8555CDS BOARD
-M:	Priyanka Jain <priyanka.jain@nxp.com>
-S:	Maintained
-F:	board/freescale/mpc8555cds/
-F:	include/configs/MPC8555CDS.h
-F:	configs/MPC8555CDS_defconfig
-F:	configs/MPC8555CDS_legacy_defconfig
diff --git a/board/freescale/mpc8555cds/Makefile b/board/freescale/mpc8555cds/Makefile
deleted file mode 100644
index f121c2fa6b2a..000000000000
--- a/board/freescale/mpc8555cds/Makefile
+++ /dev/null
@@ -1,10 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright 2004 Freescale Semiconductor.
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-
-obj-y	+= mpc8555cds.o
-obj-y	+= ddr.o
-obj-y	+= law.o
-obj-y	+= tlb.o
diff --git a/board/freescale/mpc8555cds/ddr.c b/board/freescale/mpc8555cds/ddr.c
deleted file mode 100644
index 05c56a85d246..000000000000
--- a/board/freescale/mpc8555cds/ddr.c
+++ /dev/null
@@ -1,53 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright 2008 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-
-#include <fsl_ddr_sdram.h>
-#include <fsl_ddr_dimm_params.h>
-
-void fsl_ddr_board_options(memctl_options_t *popts,
-				dimm_params_t *pdimm,
-				unsigned int ctrl_num)
-{
-	/*
-	 * Factors to consider for clock adjust:
-	 *	- number of chips on bus
-	 *	- position of slot
-	 *	- DDR1 vs. DDR2?
-	 *	- ???
-	 *
-	 * This needs to be determined on a board-by-board basis.
-	 *	0110	3/4 cycle late
-	 *	0111	7/8 cycle late
-	 */
-	popts->clk_adjust = 6;
-
-	/*
-	 * Factors to consider for CPO:
-	 *	- frequency
-	 *	- ddr1 vs. ddr2
-	 */
-	popts->cpo_override = 0;
-
-	/*
-	 * Factors to consider for write data delay:
-	 *	- number of DIMMs
-	 *
-	 * 1 = 1/4 clock delay
-	 * 2 = 1/2 clock delay
-	 * 3 = 3/4 clock delay
-	 * 4 = 1   clock delay
-	 * 5 = 5/4 clock delay
-	 * 6 = 3/2 clock delay
-	 */
-	popts->write_data_delay = 3;
-
-	/*
-	 * Factors to consider for half-strength driver enable:
-	 *	- number of DIMMs installed
-	 */
-	popts->half_strength_driver_enable = 0;
-}
diff --git a/board/freescale/mpc8555cds/law.c b/board/freescale/mpc8555cds/law.c
deleted file mode 100644
index 69f151b61513..000000000000
--- a/board/freescale/mpc8555cds/law.c
+++ /dev/null
@@ -1,41 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- */
-
-#include <common.h>
-#include <asm/fsl_law.h>
-#include <asm/mmu.h>
-
-/*
- * LAW(Local Access Window) configuration:
- *
- * 0x0000_0000     0x7fff_ffff     DDR                     2G
- * 0x8000_0000     0x9fff_ffff     PCI1 MEM                512M
- * 0xa000_0000     0xbfff_ffff     PCI2 MEM                512M
- * 0xe000_0000     0xe000_ffff     CCSR                    1M
- * 0xe200_0000     0xe20f_ffff     PCI1 IO                 1M
- * 0xe210_0000     0xe21f_ffff     PCI2 IO                 1M
- * 0xf000_0000     0xf7ff_ffff     SDRAM                   128M
- * 0xf800_0000     0xf80f_ffff     NVRAM/CADMUS (*)        1M
- * 0xff00_0000     0xff7f_ffff     FLASH (2nd bank)        8M
- * 0xff80_0000     0xffff_ffff     FLASH (boot bank)       8M
- *
- * Notes:
- *    CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
- *    If flash is 8M at default position (last 8M), no LAW needed.
- */
-
-struct law_entry law_table[] = {
-	SET_LAW(CONFIG_SYS_PCI1_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI),
-	SET_LAW(CONFIG_SYS_PCI2_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI_2),
-	SET_LAW(CONFIG_SYS_PCI1_IO_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_PCI),
-	SET_LAW(CONFIG_SYS_PCI2_IO_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_PCI_2),
-	/* LBC window - maps 256M 0xf0000000 -> 0xffffffff */
-	SET_LAW(CONFIG_SYS_LBC_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
-};
-
-int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/mpc8555cds/mpc8555cds.c b/board/freescale/mpc8555cds/mpc8555cds.c
deleted file mode 100644
index 3bb8e769c80a..000000000000
--- a/board/freescale/mpc8555cds/mpc8555cds.c
+++ /dev/null
@@ -1,430 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2004, 2011 Freescale Semiconductor.
- */
-
-#include <common.h>
-#include <init.h>
-#include <pci.h>
-#include <vsprintf.h>
-#include <asm/processor.h>
-#include <asm/mmu.h>
-#include <asm/immap_85xx.h>
-#include <fsl_ddr_sdram.h>
-#include <ioports.h>
-#include <spd_sdram.h>
-#include <linux/delay.h>
-#include <linux/libfdt.h>
-#include <fdt_support.h>
-
-#include "../common/cadmus.h"
-#include "../common/eeprom.h"
-#include "../common/via.h"
-
-#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
-extern void ddr_enable_ecc(unsigned int dram_size);
-#endif
-
-void local_bus_init(void);
-
-/*
- * I/O Port configuration table
- *
- * if conf is 1, then that port pin will be configured at boot time
- * according to the five values podr/pdir/ppar/psor/pdat for that entry
- */
-
-const iop_conf_t iop_conf_tab[4][32] = {
-
-    /* Port A configuration */
-    {   /*            conf ppar psor pdir podr pdat */
-	/* PA31 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 TxENB */
-	/* PA30 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 TxClav   */
-	/* PA29 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 TxSOC  */
-	/* PA28 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 RxENB */
-	/* PA27 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 RxSOC */
-	/* PA26 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 RxClav */
-	/* PA25 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[0] */
-	/* PA24 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[1] */
-	/* PA23 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[2] */
-	/* PA22 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[3] */
-	/* PA21 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[4] */
-	/* PA20 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[5] */
-	/* PA19 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[6] */
-	/* PA18 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[7] */
-	/* PA17 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[7] */
-	/* PA16 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[6] */
-	/* PA15 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[5] */
-	/* PA14 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[4] */
-	/* PA13 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[3] */
-	/* PA12 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[2] */
-	/* PA11 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[1] */
-	/* PA10 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[0] */
-	/* PA9  */ {   0,   1,   1,   1,   0,   0   }, /* FCC1 L1TXD */
-	/* PA8  */ {   0,   1,   1,   0,   0,   0   }, /* FCC1 L1RXD */
-	/* PA7  */ {   0,   0,   0,   1,   0,   0   }, /* PA7 */
-	/* PA6  */ {   0,   1,   1,   1,   0,   0   }, /* TDM A1 L1RSYNC */
-	/* PA5  */ {   0,   0,   0,   1,   0,   0   }, /* PA5 */
-	/* PA4  */ {   0,   0,   0,   1,   0,   0   }, /* PA4 */
-	/* PA3  */ {   0,   0,   0,   1,   0,   0   }, /* PA3 */
-	/* PA2  */ {   0,   0,   0,   1,   0,   0   }, /* PA2 */
-	/* PA1  */ {   1,   0,   0,   0,   0,   0   }, /* FREERUN */
-	/* PA0  */ {   0,   0,   0,   1,   0,   0   }  /* PA0 */
-    },
-
-    /* Port B configuration */
-    {   /*            conf ppar psor pdir podr pdat */
-	/* PB31 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TX_ER */
-	/* PB30 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_DV */
-	/* PB29 */ {   1,   1,   1,   1,   0,   0   }, /* FCC2 MII TX_EN */
-	/* PB28 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_ER */
-	/* PB27 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII COL */
-	/* PB26 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII CRS */
-	/* PB25 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[3] */
-	/* PB24 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[2] */
-	/* PB23 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[1] */
-	/* PB22 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[0] */
-	/* PB21 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[0] */
-	/* PB20 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[1] */
-	/* PB19 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[2] */
-	/* PB18 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[3] */
-	/* PB17 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RX_DIV */
-	/* PB16 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RX_ERR */
-	/* PB15 */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TX_ERR */
-	/* PB14 */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TX_EN */
-	/* PB13 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:COL */
-	/* PB12 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:CRS */
-	/* PB11 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
-	/* PB10 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
-	/* PB9  */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
-	/* PB8  */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
-	/* PB7  */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
-	/* PB6  */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
-	/* PB5  */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
-	/* PB4  */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
-	/* PB3  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PB2  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PB1  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PB0  */ {   0,   0,   0,   0,   0,   0   }  /* pin doesn't exist */
-    },
-
-    /* Port C */
-    {   /*            conf ppar psor pdir podr pdat */
-	/* PC31 */ {   0,   0,   0,   1,   0,   0   }, /* PC31 */
-	/* PC30 */ {   0,   0,   0,   1,   0,   0   }, /* PC30 */
-	/* PC29 */ {   0,   1,   1,   0,   0,   0   }, /* SCC1 EN *CLSN */
-	/* PC28 */ {   0,   0,   0,   1,   0,   0   }, /* PC28 */
-	/* PC27 */ {   0,   0,   0,   1,   0,   0   }, /* UART Clock in */
-	/* PC26 */ {   0,   0,   0,   1,   0,   0   }, /* PC26 */
-	/* PC25 */ {   0,   0,   0,   1,   0,   0   }, /* PC25 */
-	/* PC24 */ {   0,   0,   0,   1,   0,   0   }, /* PC24 */
-	/* PC23 */ {   0,   1,   0,   1,   0,   0   }, /* ATMTFCLK */
-	/* PC22 */ {   0,   1,   0,   0,   0,   0   }, /* ATMRFCLK */
-	/* PC21 */ {   0,   1,   0,   0,   0,   0   }, /* SCC1 EN RXCLK */
-	/* PC20 */ {   0,   1,   0,   0,   0,   0   }, /* SCC1 EN TXCLK */
-	/* PC19 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_CLK CLK13 */
-	/* PC18 */ {   1,   1,   0,   0,   0,   0   }, /* FCC Tx Clock (CLK14) */
-	/* PC17 */ {   0,   0,   0,   1,   0,   0   }, /* PC17 */
-	/* PC16 */ {   0,   1,   0,   0,   0,   0   }, /* FCC Tx Clock (CLK16) */
-	/* PC15 */ {   1,   1,   0,   0,   0,   0   }, /* PC15 */
-	/* PC14 */ {   0,   1,   0,   0,   0,   0   }, /* SCC1 EN *CD */
-	/* PC13 */ {   0,   0,   0,   1,   0,   0   }, /* PC13 */
-	/* PC12 */ {   0,   1,   0,   1,   0,   0   }, /* PC12 */
-	/* PC11 */ {   0,   0,   0,   1,   0,   0   }, /* LXT971 transmit control */
-	/* PC10 */ {   1,   0,   0,   1,   0,   0   }, /* FETHMDC */
-	/* PC9  */ {   1,   0,   0,   0,   0,   0   }, /* FETHMDIO */
-	/* PC8  */ {   0,   0,   0,   1,   0,   0   }, /* PC8 */
-	/* PC7  */ {   0,   0,   0,   1,   0,   0   }, /* PC7 */
-	/* PC6  */ {   0,   0,   0,   1,   0,   0   }, /* PC6 */
-	/* PC5  */ {   0,   0,   0,   1,   0,   0   }, /* PC5 */
-	/* PC4  */ {   0,   0,   0,   1,   0,   0   }, /* PC4 */
-	/* PC3  */ {   0,   0,   0,   1,   0,   0   }, /* PC3 */
-	/* PC2  */ {   0,   0,   0,   1,   0,   1   }, /* ENET FDE */
-	/* PC1  */ {   0,   0,   0,   1,   0,   0   }, /* ENET DSQE */
-	/* PC0  */ {   0,   0,   0,   1,   0,   0   }, /* ENET LBK */
-    },
-
-    /* Port D */
-    {   /*            conf ppar psor pdir podr pdat */
-	/* PD31 */ {   1,   1,   0,   0,   0,   0   }, /* SCC1 EN RxD */
-	/* PD30 */ {   1,   1,   1,   1,   0,   0   }, /* SCC1 EN TxD */
-	/* PD29 */ {   1,   1,   0,   1,   0,   0   }, /* SCC1 EN TENA */
-	/* PD28 */ {   0,   1,   0,   0,   0,   0   }, /* PD28 */
-	/* PD27 */ {   0,   1,   1,   1,   0,   0   }, /* PD27 */
-	/* PD26 */ {   0,   0,   0,   1,   0,   0   }, /* PD26 */
-	/* PD25 */ {   0,   0,   0,   1,   0,   0   }, /* PD25 */
-	/* PD24 */ {   0,   0,   0,   1,   0,   0   }, /* PD24 */
-	/* PD23 */ {   0,   0,   0,   1,   0,   0   }, /* PD23 */
-	/* PD22 */ {   0,   0,   0,   1,   0,   0   }, /* PD22 */
-	/* PD21 */ {   0,   0,   0,   1,   0,   0   }, /* PD21 */
-	/* PD20 */ {   0,   0,   0,   1,   0,   0   }, /* PD20 */
-	/* PD19 */ {   0,   0,   0,   1,   0,   0   }, /* PD19 */
-	/* PD18 */ {   0,   0,   0,   1,   0,   0   }, /* PD18 */
-	/* PD17 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXPRTY */
-	/* PD16 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXPRTY */
-	/* PD15 */ {   0,   1,   1,   0,   1,   0   }, /* I2C SDA */
-	/* PD14 */ {   0,   0,   0,   1,   0,   0   }, /* LED */
-	/* PD13 */ {   0,   0,   0,   0,   0,   0   }, /* PD13 */
-	/* PD12 */ {   0,   0,   0,   0,   0,   0   }, /* PD12 */
-	/* PD11 */ {   0,   0,   0,   0,   0,   0   }, /* PD11 */
-	/* PD10 */ {   0,   0,   0,   0,   0,   0   }, /* PD10 */
-	/* PD9  */ {   0,   1,   0,   1,   0,   0   }, /* SMC1 TXD */
-	/* PD8  */ {   0,   1,   0,   0,   0,   0   }, /* SMC1 RXD */
-	/* PD7  */ {   0,   0,   0,   1,   0,   1   }, /* PD7 */
-	/* PD6  */ {   0,   0,   0,   1,   0,   1   }, /* PD6 */
-	/* PD5  */ {   0,   0,   0,   1,   0,   1   }, /* PD5 */
-	/* PD4  */ {   0,   0,   0,   1,   0,   1   }, /* PD4 */
-	/* PD3  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PD2  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PD1  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PD0  */ {   0,   0,   0,   0,   0,   0   }  /* pin doesn't exist */
-    }
-};
-
-int checkboard (void)
-{
-	volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
-	char buf[32];
-
-	/* PCI slot in USER bits CSR[6:7] by convention. */
-	uint pci_slot = get_pci_slot ();
-
-	uint pci_dual = get_pci_dual ();	/* PCI DUAL in CM_PCI[3] */
-	uint pci1_32 = gur->pordevsr & 0x10000;	/* PORDEVSR[15] */
-	uint pci1_clk_sel = gur->porpllsr & 0x8000;	/* PORPLLSR[16] */
-	uint pci2_clk_sel = gur->porpllsr & 0x4000;	/* PORPLLSR[17] */
-
-	uint pci1_speed = get_clock_freq ();	/* PCI PSPEED in [4:5] */
-
-	uint cpu_board_rev = get_cpu_board_revision ();
-
-	printf ("Board: CDS Version 0x%02x, PCI Slot %d\n",
-		get_board_version (), pci_slot);
-
-	printf ("CPU Board Revision %d.%d (0x%04x)\n",
-		MPC85XX_CPU_BOARD_MAJOR (cpu_board_rev),
-		MPC85XX_CPU_BOARD_MINOR (cpu_board_rev), cpu_board_rev);
-
-	printf("PCI1: %d bit, %s MHz, %s\n",
-		(pci1_32) ? 32 : 64,
-		strmhz(buf, pci1_speed),
-		pci1_clk_sel ? "sync" : "async");
-
-	if (pci_dual) {
-		printf("PCI2: 32 bit, 66 MHz, %s\n",
-			pci2_clk_sel ? "sync" : "async");
-	} else {
-		printf("PCI2: disabled\n");
-	}
-
-	/*
-	 * Initialize local bus.
-	 */
-	local_bus_init ();
-
-	return 0;
-}
-
-/*
- * Initialize Local Bus
- */
-void
-local_bus_init(void)
-{
-	volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
-	volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
-
-	uint clkdiv;
-	uint lbc_hz;
-	sys_info_t sysinfo;
-	uint temp_lbcdll;
-
-	/*
-	 * Errata LBC11.
-	 * Fix Local Bus clock glitch when DLL is enabled.
-	 *
-	 * If localbus freq is < 66MHz, DLL bypass mode must be used.
-	 * If localbus freq is > 133MHz, DLL can be safely enabled.
-	 * Between 66 and 133, the DLL is enabled with an override workaround.
-	 */
-
-	get_sys_info(&sysinfo);
-	clkdiv = lbc->lcrr & LCRR_CLKDIV;
-	lbc_hz = sysinfo.freq_systembus / 1000000 / clkdiv;
-
-	if (lbc_hz < 66) {
-		lbc->lcrr |= LCRR_DBYP;	/* DLL Bypass */
-
-	} else if (lbc_hz >= 133) {
-		lbc->lcrr &= (~LCRR_DBYP);		/* DLL Enabled */
-
-	} else {
-		lbc->lcrr &= (~LCRR_DBYP);	/* DLL Enabled */
-		udelay(200);
-
-		/*
-		 * Sample LBC DLL ctrl reg, upshift it to set the
-		 * override bits.
-		 */
-		temp_lbcdll = gur->lbcdllcr;
-		gur->lbcdllcr = (((temp_lbcdll & 0xff) << 16) | 0x80000000);
-		asm("sync;isync;msync");
-	}
-}
-
-/*
- * Initialize SDRAM memory on the Local Bus.
- */
-void lbc_sdram_init(void)
-{
-#if defined(CONFIG_SYS_OR2_PRELIM) && defined(CONFIG_SYS_BR2_PRELIM)
-
-	uint idx;
-	volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
-	uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE;
-	uint cpu_board_rev;
-	uint lsdmr_common;
-
-	puts("LBC SDRAM: ");
-	print_size(CONFIG_SYS_LBC_SDRAM_SIZE * 1024 * 1024,
-		   "\n       ");
-
-	/*
-	 * Setup SDRAM Base and Option Registers
-	 */
-	set_lbc_or(2, CONFIG_SYS_OR2_PRELIM);
-	set_lbc_br(2, CONFIG_SYS_BR2_PRELIM);
-	lbc->lbcr = CONFIG_SYS_LBC_LBCR;
-	asm("msync");
-
-	lbc->lsrt = CONFIG_SYS_LBC_LSRT;
-	lbc->mrtpr = CONFIG_SYS_LBC_MRTPR;
-	asm("msync");
-
-	/*
-	 * Determine which address lines to use baed on CPU board rev.
-	 */
-	cpu_board_rev = get_cpu_board_revision();
-	lsdmr_common = CONFIG_SYS_LBC_LSDMR_COMMON;
-	if (cpu_board_rev == MPC85XX_CPU_BOARD_REV_1_0) {
-		lsdmr_common |= LSDMR_BSMA1617;
-	} else if (cpu_board_rev == MPC85XX_CPU_BOARD_REV_1_1) {
-		lsdmr_common |= LSDMR_BSMA1516;
-	} else {
-		/*
-		 * Assume something unable to identify itself is
-		 * really old, and likely has lines 16/17 mapped.
-		 */
-		lsdmr_common |= LSDMR_BSMA1617;
-	}
-
-	/*
-	 * Issue PRECHARGE ALL command.
-	 */
-	lbc->lsdmr = lsdmr_common | LSDMR_OP_PCHALL;
-	asm("sync;msync");
-	*sdram_addr = 0xff;
-	ppcDcbf((unsigned long) sdram_addr);
-	udelay(100);
-
-	/*
-	 * Issue 8 AUTO REFRESH commands.
-	 */
-	for (idx = 0; idx < 8; idx++) {
-		lbc->lsdmr = lsdmr_common | LSDMR_OP_ARFRSH;
-		asm("sync;msync");
-		*sdram_addr = 0xff;
-		ppcDcbf((unsigned long) sdram_addr);
-		udelay(100);
-	}
-
-	/*
-	 * Issue 8 MODE-set command.
-	 */
-	lbc->lsdmr = lsdmr_common | LSDMR_OP_MRW;
-	asm("sync;msync");
-	*sdram_addr = 0xff;
-	ppcDcbf((unsigned long) sdram_addr);
-	udelay(100);
-
-	/*
-	 * Issue NORMAL OP command.
-	 */
-	lbc->lsdmr = lsdmr_common | LSDMR_OP_NORMAL;
-	asm("sync;msync");
-	*sdram_addr = 0xff;
-	ppcDcbf((unsigned long) sdram_addr);
-	udelay(200);    /* Overkill. Must wait > 200 bus cycles */
-
-#endif	/* enable SDRAM init */
-}
-
-#ifdef CONFIG_PCI
-/* For some reason the Tundra PCI bridge shows up on itself as a
- * different device.  Work around that by refusing to configure it
- */
-void dummy_func(struct pci_controller* hose, pci_dev_t dev, struct pci_config_table *tab) { }
-
-static struct pci_config_table pci_mpc85xxcds_config_table[] = {
-	{0x10e3, 0x0513, PCI_ANY_ID, 1, 3, PCI_ANY_ID, dummy_func, {0,0,0}},
-	{0x1106, 0x0686, PCI_ANY_ID, 1, VIA_ID, 0, mpc85xx_config_via, {0,0,0}},
-	{0x1106, 0x0571, PCI_ANY_ID, 1, VIA_ID, 1,
-		mpc85xx_config_via_usbide, {0,0,0}},
-	{0x1105, 0x3038, PCI_ANY_ID, 1, VIA_ID, 2,
-		mpc85xx_config_via_usb, {0,0,0}},
-	{0x1106, 0x3038, PCI_ANY_ID, 1, VIA_ID, 3,
-		mpc85xx_config_via_usb2, {0,0,0}},
-	{0x1106, 0x3058, PCI_ANY_ID, 1, VIA_ID, 5,
-		mpc85xx_config_via_power, {0,0,0}},
-	{0x1106, 0x3068, PCI_ANY_ID, 1, VIA_ID, 6,
-		mpc85xx_config_via_ac97, {0,0,0}},
-	{},
-};
-
-
-static struct pci_controller hose[] = {
-	{
-	config_table: pci_mpc85xxcds_config_table,
-	},
-#ifdef CONFIG_MPC85XX_PCI2
-	{},
-#endif
-};
-
-#endif
-
-void
-pci_init_board(void)
-{
-#ifdef CONFIG_PCI
-	pci_mpc85xx_init(hose);
-#endif
-}
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-void
-ft_pci_setup(void *blob, struct bd_info *bd)
-{
-	int node, tmp[2];
-	const char *path;
-
-	node = fdt_path_offset(blob, "/aliases");
-	tmp[0] = 0;
-	if (node >= 0) {
-#ifdef CONFIG_PCI1
-		path = fdt_getprop(blob, node, "pci0", NULL);
-		if (path) {
-			tmp[1] = hose[0].last_busno - hose[0].first_busno;
-			do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
-		}
-#endif
-#ifdef CONFIG_MPC85XX_PCI2
-		path = fdt_getprop(blob, node, "pci1", NULL);
-		if (path) {
-			tmp[1] = hose[1].last_busno - hose[1].first_busno;
-			do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
-		}
-#endif
-	}
-}
-#endif
diff --git a/board/freescale/mpc8555cds/tlb.c b/board/freescale/mpc8555cds/tlb.c
deleted file mode 100644
index 4a18f05af0d1..000000000000
--- a/board/freescale/mpc8555cds/tlb.c
+++ /dev/null
@@ -1,95 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-
-struct fsl_e_tlb_entry tlb_table[] = {
-	/* TLB 0 - for temp stack in cache */
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-
-	/*
-	 * TLB 0:	16M	Non-cacheable, guarded
-	 * 0xff000000	16M	FLASH
-	 * Out of reset this entry is only 4K.
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 0, BOOKE_PAGESZ_16M, 1),
-
-	/*
-	 * TLB 1:	256M	Non-cacheable, guarded
-	 * 0x80000000	256M	PCI1 MEM First half
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_MEM_VIRT, CONFIG_SYS_PCI1_MEM_PHYS,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 1, BOOKE_PAGESZ_256M, 1),
-
-	/*
-	 * TLB 2:	256M	Non-cacheable, guarded
-	 * 0x90000000	256M	PCI1 MEM Second half
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_MEM_VIRT + 0x10000000, CONFIG_SYS_PCI1_MEM_PHYS + 0x10000000,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 2, BOOKE_PAGESZ_256M, 1),
-
-	/*
-	 * TLB 3:	256M	Non-cacheable, guarded
-	 * 0xa0000000	256M	PCI2 MEM First half
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_PCI2_MEM_VIRT, CONFIG_SYS_PCI2_MEM_PHYS,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 3, BOOKE_PAGESZ_256M, 1),
-
-	/*
-	 * TLB 4:	256M	Non-cacheable, guarded
-	 * 0xb0000000	256M	PCI2 MEM Second half
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_PCI2_MEM_VIRT + 0x10000000, CONFIG_SYS_PCI2_MEM_PHYS + 0x10000000,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 4, BOOKE_PAGESZ_256M, 1),
-
-	/*
-	 * TLB 5:	64M	Non-cacheable, guarded
-	 * 0xe000_0000	1M	CCSRBAR
-	 * 0xe200_0000	16M	PCI1 IO
-	 * 0xe300_0000	16M	PCI2 IO
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 5, BOOKE_PAGESZ_64M, 1),
-
-	/*
-	 * TLB 6:	64M	Cacheable, non-guarded
-	 * 0xf000_0000	64M	LBC SDRAM
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_LBC_SDRAM_BASE, CONFIG_SYS_LBC_SDRAM_BASE,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 6, BOOKE_PAGESZ_64M, 1),
-
-	/*
-	 * TLB 7:	1M	Non-cacheable, guarded
-	 * 0xf8000000	1M	CADMUS registers
-	 */
-	SET_TLB_ENTRY(1, CADMUS_BASE_ADDR, CADMUS_BASE_ADDR,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 7, BOOKE_PAGESZ_1M, 1),
-};
-
-int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/configs/MPC8555CDS_defconfig b/configs/MPC8555CDS_defconfig
deleted file mode 100644
index e7a5ca00b980..000000000000
--- a/configs/MPC8555CDS_defconfig
+++ /dev/null
@@ -1,40 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xfff80000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x40000
-CONFIG_MPC85xx=y
-# CONFIG_CMD_ERRATA is not set
-CONFIG_TARGET_MPC8555CDS=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=10
-# CONFIG_MISC_INIT_R is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_REGINFO=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-# CONFIG_CMD_HASH is not set
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_ENV_ADDR=0xFFFC0000
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_MII=y
-CONFIG_TSEC_ENET=y
-CONFIG_CONS_INDEX=2
-CONFIG_SYS_NS16550=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/MPC8555CDS_legacy_defconfig b/configs/MPC8555CDS_legacy_defconfig
deleted file mode 100644
index 5780138f85d7..000000000000
--- a/configs/MPC8555CDS_legacy_defconfig
+++ /dev/null
@@ -1,41 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xfff80000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x40000
-CONFIG_MPC85xx=y
-# CONFIG_CMD_ERRATA is not set
-CONFIG_TARGET_MPC8555CDS=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="LEGACY"
-CONFIG_BOOTDELAY=10
-# CONFIG_MISC_INIT_R is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_REGINFO=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-# CONFIG_CMD_HASH is not set
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_ENV_ADDR=0xFFFC0000
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_MII=y
-CONFIG_TSEC_ENET=y
-CONFIG_CONS_INDEX=2
-CONFIG_SYS_NS16550=y
-CONFIG_OF_LIBFDT=y
diff --git a/drivers/ddr/fsl/ctrl_regs.c b/drivers/ddr/fsl/ctrl_regs.c
index b80034478e11..b5122d1a1c37 100644
--- a/drivers/ddr/fsl/ctrl_regs.c
+++ b/drivers/ddr/fsl/ctrl_regs.c
@@ -1863,25 +1863,13 @@ static void set_ddr_data_init(fsl_ddr_cfg_regs_t *ddr)
 static void set_ddr_sdram_clk_cntl(fsl_ddr_cfg_regs_t *ddr,
 					 const memctl_options_t *popts)
 {
-	unsigned int clk_adjust;	/* Clock adjust */
-	unsigned int ss_en = 0;		/* Source synchronous enable */
-
-#if defined(CONFIG_ARCH_MPC8555)
-	/* Per FSL Application Note: AN2805 */
-	ss_en = 1;
-#endif
-	if (fsl_ddr_get_version(0) >= 0x40701) {
+	if (fsl_ddr_get_version(0) >= 0x40701)
 		/* clk_adjust in 5-bits on T-series and LS-series */
-		clk_adjust = (popts->clk_adjust & 0x1F) << 22;
-	} else {
+		ddr->ddr_sdram_clk_cntl = (popts->clk_adjust & 0x1F) << 22;
+	else
 		/* clk_adjust in 4-bits on earlier MPC85xx and P-series */
-		clk_adjust = (popts->clk_adjust & 0xF) << 23;
-	}
+		ddr->ddr_sdram_clk_cntl = (popts->clk_adjust & 0xF) << 23;
 
-	ddr->ddr_sdram_clk_cntl = (0
-				   | ((ss_en & 0x1) << 31)
-				   | clk_adjust
-				   );
 	debug("FSLDDR: clk_cntl = 0x%08x\n", ddr->ddr_sdram_clk_cntl);
 }
 
diff --git a/drivers/ddr/fsl/mpc85xx_ddr_gen1.c b/drivers/ddr/fsl/mpc85xx_ddr_gen1.c
index c642a5b1eec4..9c2ddeaf932f 100644
--- a/drivers/ddr/fsl/mpc85xx_ddr_gen1.c
+++ b/drivers/ddr/fsl/mpc85xx_ddr_gen1.c
@@ -48,9 +48,6 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
 	out_be32(&ddr->timing_cfg_2, regs->timing_cfg_2);
 	out_be32(&ddr->sdram_mode, regs->ddr_sdram_mode);
 	out_be32(&ddr->sdram_interval, regs->ddr_sdram_interval);
-#if defined(CONFIG_ARCH_MPC8555)
-	out_be32(&ddr->sdram_clk_cntl, regs->ddr_sdram_clk_cntl);
-#endif
 
 	/*
 	 * 200 painful micro-seconds must elapse between
diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h
deleted file mode 100644
index 79e309c95c13..000000000000
--- a/include/configs/MPC8555CDS.h
+++ /dev/null
@@ -1,380 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2004, 2011 Freescale Semiconductor.
- */
-
-/*
- * mpc8555cds board configuration file
- *
- * Please refer to doc/README.mpc85xxcds for more info.
- *
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* High Level Configuration Options */
-#define CONFIG_CPM2		1	/* has CPM2 */
-
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
-
-#ifndef __ASSEMBLY__
-extern unsigned long get_clock_freq(void);
-#endif
-#define CONFIG_SYS_CLK_FREQ	get_clock_freq() /* sysclk for MPC85xx */
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE			    /* toggle L2 cache	*/
-#define CONFIG_BTB			    /* toggle branch predition */
-
-#define CONFIG_SYS_CCSRBAR		0xe0000000
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
-
-/* DDR Setup */
-#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_SPD
-
-#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
-
-#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_DIMM_SLOTS_PER_CTLR	1
-#define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
-
-/* I2C addresses of SPD EEPROMs */
-#define SPD_EEPROM_ADDRESS	0x51	/* CTLR 0 DIMM 0 */
-
-/* Make sure required options are set */
-#ifndef CONFIG_SPD_EEPROM
-#error ("CONFIG_SPD_EEPROM is required by MPC85555CDS")
-#endif
-
-/*
- * Local Bus Definitions
- */
-
-/*
- * FLASH on the Local Bus
- * Two banks, 8M each, using the CFI driver.
- * Boot from BR0/OR0 bank at 0xff00_0000
- * Alternate BR1/OR1 bank at 0xff80_0000
- *
- * BR0, BR1:
- *    Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0
- *    Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0
- *    Port Size = 16 bits = BRx[19:20] = 10
- *    Use GPCM = BRx[24:26] = 000
- *    Valid = BRx[31] = 1
- *
- * 0    4    8    12   16   20   24   28
- * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001    BR0
- * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001    BR1
- *
- * OR0, OR1:
- *    Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0
- *    Reserved ORx[17:18] = 11, confusion here?
- *    CSNT = ORx[20] = 1
- *    ACS = half cycle delay = ORx[21:22] = 11
- *    SCY = 6 = ORx[24:27] = 0110
- *    TRLX = use relaxed timing = ORx[29] = 1
- *    EAD = use external address latch delay = OR[31] = 1
- *
- * 0    4    8    12   16   20   24   28
- * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65    ORx
- */
-
-#define CONFIG_SYS_FLASH_BASE		0xff000000	/* start of FLASH 8M */
-
-#define CONFIG_SYS_BR0_PRELIM		0xff801001
-#define CONFIG_SYS_BR1_PRELIM		0xff001001
-
-#define	CONFIG_SYS_OR0_PRELIM		0xff806e65
-#define	CONFIG_SYS_OR1_PRELIM		0xff806e65
-
-#define CONFIG_SYS_FLASH_BANKS_LIST	{0xff800000, CONFIG_SYS_FLASH_BASE}
-#define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	128		/* sectors per device */
-#undef	CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-/*
- * SDRAM on the Local Bus
- */
-#define CONFIG_SYS_LBC_SDRAM_BASE	0xf0000000	/* Localbus SDRAM */
-#define CONFIG_SYS_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */
-
-/*
- * Base Register 2 and Option Register 2 configure SDRAM.
- * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
- *
- * For BR2, need:
- *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
- *    port-size = 32-bits = BR2[19:20] = 11
- *    no parity checking = BR2[21:22] = 00
- *    SDRAM for MSEL = BR2[24:26] = 011
- *    Valid = BR[31] = 1
- *
- * 0    4    8    12   16   20   24   28
- * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
- *
- * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into
- * FIXME: the top 17 bits of BR2.
- */
-
-#define CONFIG_SYS_BR2_PRELIM          0xf0001861
-
-/*
- * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
- *
- * For OR2, need:
- *    64MB mask for AM, OR2[0:7] = 1111 1100
- *		   XAM, OR2[17:18] = 11
- *    9 columns OR2[19-21] = 010
- *    13 rows   OR2[23-25] = 100
- *    EAD set for extra time OR[31] = 1
- *
- * 0    4    8    12   16   20   24   28
- * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
- */
-
-#define CONFIG_SYS_OR2_PRELIM		0xfc006901
-
-#define CONFIG_SYS_LBC_LCRR		0x00030004    /* LB clock ratio reg */
-#define CONFIG_SYS_LBC_LBCR		0x00000000    /* LB config reg */
-#define CONFIG_SYS_LBC_LSRT		0x20000000  /* LB sdram refresh timer */
-#define CONFIG_SYS_LBC_MRTPR		0x00000000  /* LB refresh timer prescal*/
-
-/*
- * Common settings for all Local Bus SDRAM commands.
- * At run time, either BSMA1516 (for CPU 1.1)
- *                  or BSMA1617 (for CPU 1.0) (old)
- * is OR'ed in too.
- */
-#define CONFIG_SYS_LBC_LSDMR_COMMON	( LSDMR_RFCR16		\
-				| LSDMR_PRETOACT7	\
-				| LSDMR_ACTTORW7	\
-				| LSDMR_BL8		\
-				| LSDMR_WRC4		\
-				| LSDMR_CL3		\
-				| LSDMR_RFEN		\
-				)
-
-/*
- * The CADMUS registers are connected to CS3 on CDS.
- * The new memory map places CADMUS at 0xf8000000.
- *
- * For BR3, need:
- *    Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0
- *    port-size = 8-bits  = BR[19:20] = 01
- *    no parity checking  = BR[21:22] = 00
- *    GPMC for MSEL       = BR[24:26] = 000
- *    Valid               = BR[31]    = 1
- *
- * 0    4    8    12   16   20   24   28
- * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801
- *
- * For OR3, need:
- *    1 MB mask for AM,   OR[0:16]  = 1111 1111 1111 0000 0
- *    disable buffer ctrl OR[19]    = 0
- *    CSNT                OR[20]    = 1
- *    ACS                 OR[21:22] = 11
- *    XACS                OR[23]    = 1
- *    SCY 15 wait states  OR[24:27] = 1111	max is suboptimal but safe
- *    SETA                OR[28]    = 0
- *    TRLX                OR[29]    = 1
- *    EHTR                OR[30]    = 1
- *    EAD extra time      OR[31]    = 1
- *
- * 0    4    8    12   16   20   24   28
- * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7
- */
-
-#define CONFIG_FSL_CADMUS
-
-#define CADMUS_BASE_ADDR 0xf8000000
-#define CONFIG_SYS_BR3_PRELIM   0xf8000801
-#define CONFIG_SYS_OR3_PRELIM   0xfff00ff7
-
-#define CONFIG_SYS_INIT_RAM_LOCK	1
-#define CONFIG_SYS_INIT_RAM_ADDR	0xe4010000	/* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x4000	    /* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN		(128 * 1024)	/* Reserved for malloc */
-
-/* Serial Port */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE    1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE  \
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-
-#define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_CCSRBAR+0x4500)
-#define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_CCSRBAR+0x4600)
-
-/*
- * I2C
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	400000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }
-
-/* EEPROM */
-#define CONFIG_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_CCID
-#define CONFIG_SYS_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_ADDR     0x57
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCI1_MEM_VIRT	0x80000000
-#define CONFIG_SYS_PCI1_MEM_BUS	0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS	0x80000000
-#define CONFIG_SYS_PCI1_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCI1_IO_VIRT	0xe2000000
-#define CONFIG_SYS_PCI1_IO_BUS	0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS	0xe2000000
-#define CONFIG_SYS_PCI1_IO_SIZE	0x00100000	/* 1M */
-
-#define CONFIG_SYS_PCI2_MEM_VIRT	0xa0000000
-#define CONFIG_SYS_PCI2_MEM_BUS	0xa0000000
-#define CONFIG_SYS_PCI2_MEM_PHYS	0xa0000000
-#define CONFIG_SYS_PCI2_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCI2_IO_VIRT	0xe2100000
-#define CONFIG_SYS_PCI2_IO_BUS	0x00000000
-#define CONFIG_SYS_PCI2_IO_PHYS	0xe2100000
-#define CONFIG_SYS_PCI2_IO_SIZE	0x00100000	/* 1M */
-
-#ifdef CONFIG_LEGACY
-#define BRIDGE_ID 17
-#define VIA_ID 2
-#else
-#define BRIDGE_ID 28
-#define VIA_ID 4
-#endif
-
-#if defined(CONFIG_PCI)
-
-#define CONFIG_MPC85XX_PCI2
-
-
-#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */
-
-#endif	/* CONFIG_PCI */
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_TSEC1	1
-#define CONFIG_TSEC1_NAME	"TSEC0"
-#define CONFIG_TSEC2	1
-#define CONFIG_TSEC2_NAME	"TSEC1"
-#define TSEC1_PHY_ADDR		0
-#define TSEC2_PHY_ADDR		1
-#define TSEC1_PHYIDX		0
-#define TSEC2_PHYIDX		0
-#define TSEC1_FLAGS		TSEC_GIGABIT
-#define TSEC2_FLAGS		TSEC_GIGABIT
-
-/* Options are: TSEC[0-1] */
-#define CONFIG_ETHPRIME		"TSEC0"
-
-#endif	/* CONFIG_TSEC_ENET */
-
-/*
- * Environment
- */
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-#endif
-
-#define CONFIG_IPADDR    192.168.1.253
-
-#define CONFIG_HOSTNAME  "unknown"
-#define CONFIG_ROOTPATH  "/nfsroot"
-#define CONFIG_BOOTFILE  "your.uImage"
-
-#define CONFIG_SERVERIP  192.168.1.1
-#define CONFIG_GATEWAYIP 192.168.1.1
-#define CONFIG_NETMASK   255.255.255.0
-
-#define CONFIG_LOADADDR  200000   /*default location for tftp and bootm*/
-
-#define	CONFIG_EXTRA_ENV_SETTINGS				        \
-   "netdev=eth0\0"                                                      \
-   "consoledev=ttyS1\0"                                                 \
-   "ramdiskaddr=600000\0"                                               \
-   "ramdiskfile=your.ramdisk.u-boot\0"					\
-   "fdtaddr=400000\0"							\
-   "fdtfile=your.fdt.dtb\0"
-
-#define CONFIG_NFSBOOTCOMMAND	                                        \
-   "setenv bootargs root=/dev/nfs rw "                                  \
-      "nfsroot=$serverip:$rootpath "                                    \
-      "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
-      "console=$consoledev,$baudrate $othbootargs;"                     \
-   "tftp $loadaddr $bootfile;"                                          \
-   "tftp $fdtaddr $fdtfile;"						\
-   "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
-   "setenv bootargs root=/dev/ram rw "                                  \
-      "console=$consoledev,$baudrate $othbootargs;"                     \
-   "tftp $ramdiskaddr $ramdiskfile;"                                    \
-   "tftp $loadaddr $bootfile;"                                          \
-   "bootm $loadaddr $ramdiskaddr"
-
-#define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND
-
-#endif	/* __CONFIG_H */
-- 
2.17.1