* [PATCH v2 0/5] Add support for the Hynix Hi-846 camera
@ 2021-05-28 8:13 Martin Kepplinger
2021-05-28 8:13 ` [PATCH v2 1/5] dt-bindings: vendor-prefixes: Add SK Hynix Inc Martin Kepplinger
` (5 more replies)
0 siblings, 6 replies; 18+ messages in thread
From: Martin Kepplinger @ 2021-05-28 8:13 UTC (permalink / raw)
To: laurent.pinchart, mchehab
Cc: devicetree, kernel, krzysztof.kozlowski, linux-kernel,
linux-media, paul.kocialkowski, robh, shawnx.tu,
Martin Kepplinger
hi,
This patchset add support for the SK Hynix Hi-846 CMOS images sensor.
It includes documentation, dt-bindings and the driver.
patch 4 and 5 are basically optional: if i2c-cardlist is deprecated,
ignore it and act on it appropriately, and the defconfig would just
be convenience for now.
best wishes,
martin
revision history
----------------
v2:
sent a bit early due to stupid mistakes
fix build issues
fix dtschema issues
add enable for arm64 defconfig
v1:
https://lore.kernel.org/linux-media/20210527091221.3335998-1-martin.kepplinger@puri.sm/
Martin Kepplinger (5):
dt-bindings: vendor-prefixes: Add SK Hynix Inc.
dt-bindings: media: document SK Hynix Hi-846 MIPI CSI-2 8M pixel
sensor
media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera
arm64: defconfig: enable VIDEO_HI846
Documentation: i2c-cardlist: add the Hynix hi846 sensor
.../admin-guide/media/i2c-cardlist.rst | 1 +
.../bindings/media/i2c/hynix,hi846.yaml | 99 +
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
MAINTAINERS | 6 +
arch/arm64/configs/defconfig | 1 +
drivers/media/i2c/Kconfig | 13 +
drivers/media/i2c/Makefile | 1 +
drivers/media/i2c/hi846.c | 2137 +++++++++++++++++
8 files changed, 2260 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
create mode 100644 drivers/media/i2c/hi846.c
--
2.30.2
^ permalink raw reply [flat|nested] 18+ messages in thread* [PATCH v2 1/5] dt-bindings: vendor-prefixes: Add SK Hynix Inc. 2021-05-28 8:13 [PATCH v2 0/5] Add support for the Hynix Hi-846 camera Martin Kepplinger @ 2021-05-28 8:13 ` Martin Kepplinger 2021-05-28 8:13 ` [PATCH v2 2/5] dt-bindings: media: document SK Hynix Hi-846 MIPI CSI-2 8M pixel sensor Martin Kepplinger ` (4 subsequent siblings) 5 siblings, 0 replies; 18+ messages in thread From: Martin Kepplinger @ 2021-05-28 8:13 UTC (permalink / raw) To: laurent.pinchart, mchehab Cc: devicetree, kernel, krzysztof.kozlowski, linux-kernel, linux-media, paul.kocialkowski, robh, shawnx.tu, Martin Kepplinger SK Hynix built the already supported hi556 sensor (and probably much more). For more information, see https://www.skhynix.com/ Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> --- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index b868cefc7c55..a75cd3be50b9 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -499,6 +499,8 @@ patternProperties: description: Hycon Technology Corp. "^hydis,.*": description: Hydis Technologies + "^hynix,.*": + description: SK Hynix Inc. "^hyundai,.*": description: Hyundai Technology "^i2se,.*": -- 2.30.2 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v2 2/5] dt-bindings: media: document SK Hynix Hi-846 MIPI CSI-2 8M pixel sensor 2021-05-28 8:13 [PATCH v2 0/5] Add support for the Hynix Hi-846 camera Martin Kepplinger 2021-05-28 8:13 ` [PATCH v2 1/5] dt-bindings: vendor-prefixes: Add SK Hynix Inc Martin Kepplinger @ 2021-05-28 8:13 ` Martin Kepplinger 2021-05-28 8:35 ` Laurent Pinchart 2021-06-02 13:51 ` Sakari Ailus 2021-05-28 8:13 ` [PATCH v2 3/5] media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera Martin Kepplinger ` (3 subsequent siblings) 5 siblings, 2 replies; 18+ messages in thread From: Martin Kepplinger @ 2021-05-28 8:13 UTC (permalink / raw) To: laurent.pinchart, mchehab Cc: devicetree, kernel, krzysztof.kozlowski, linux-kernel, linux-media, paul.kocialkowski, robh, shawnx.tu, Martin Kepplinger Document the bindings used for the SK Hynix Hi-846 CMOS camera driver. Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> --- .../bindings/media/i2c/hynix,hi846.yaml | 99 +++++++++++++++++++ 1 file changed, 99 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml diff --git a/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml new file mode 100644 index 000000000000..2991108e23e5 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml @@ -0,0 +1,99 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/hynix,hi846.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SK Hynix Hi-846 1/4" 8M Pixel MIPI CSI-2 sensor + +maintainers: + - Martin Kepplinger <martin.kepplinger@puri.sm> + +description: |- + The Hi-846 is a raw image sensor with an MIPI CSI-2 image data + interface and CCI (I2C compatible) control bus. The output format + is 10bit Bayer. + +properties: + compatible: + const: hynix,hi846 + + reg: + description: I2C device address. + maxItems: 1 + + clocks: + description: Reference to the mclk clock. + maxItems: 1 + + clock-names: + const: mclk + + rst-gpios: + description: Reference to the GPIO connected to the reset pin. Active low. + maxItems: 1 + + vdd-supply: + description: Definition of the regulator used as 1.8V digital power supply. + + port: + $ref: /schemas/graph.yaml#/properties/port + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + oneOf: + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + - items: + - const: 1 + - const: 2 + + required: + - data-lanes + +required: + - compatible + - reg + - clocks + - clock-names + - rst-gpios + - vdd-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + hi846: camera@20 { + compatible = "hynix,hi846"; + reg = <0x20>; + clocks = <&clk>; + clock-names = "mclk"; + vdd-supply = <®_camera_pwr_en>; /* 1.8v */ + rst-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; + + port { + camera_out: endpoint { + remote-endpoint = <&csi1_ep1>; + data-lanes = <1 2>; + }; + }; + }; + }; + +... -- 2.30.2 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* Re: [PATCH v2 2/5] dt-bindings: media: document SK Hynix Hi-846 MIPI CSI-2 8M pixel sensor 2021-05-28 8:13 ` [PATCH v2 2/5] dt-bindings: media: document SK Hynix Hi-846 MIPI CSI-2 8M pixel sensor Martin Kepplinger @ 2021-05-28 8:35 ` Laurent Pinchart 2021-06-02 13:52 ` Sakari Ailus 2021-06-02 13:51 ` Sakari Ailus 1 sibling, 1 reply; 18+ messages in thread From: Laurent Pinchart @ 2021-05-28 8:35 UTC (permalink / raw) To: Martin Kepplinger Cc: mchehab, devicetree, kernel, krzysztof.kozlowski, linux-kernel, linux-media, paul.kocialkowski, robh, shawnx.tu Hi Martin, Thank you for the patch. On Fri, May 28, 2021 at 10:13:33AM +0200, Martin Kepplinger wrote: > Document the bindings used for the SK Hynix Hi-846 CMOS camera driver. > > Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> > --- > .../bindings/media/i2c/hynix,hi846.yaml | 99 +++++++++++++++++++ > 1 file changed, 99 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml > > diff --git a/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml > new file mode 100644 > index 000000000000..2991108e23e5 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml > @@ -0,0 +1,99 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/media/i2c/hynix,hi846.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: SK Hynix Hi-846 1/4" 8M Pixel MIPI CSI-2 sensor > + > +maintainers: > + - Martin Kepplinger <martin.kepplinger@puri.sm> > + > +description: |- > + The Hi-846 is a raw image sensor with an MIPI CSI-2 image data > + interface and CCI (I2C compatible) control bus. The output format > + is 10bit Bayer. > + > +properties: > + compatible: > + const: hynix,hi846 > + > + reg: > + description: I2C device address. You can drop the description, it's implicit that reg is the I2C address for I2C devices. > + maxItems: 1 > + > + clocks: > + description: Reference to the mclk clock. > + maxItems: 1 You could also write this clocks: items: - description: Reference to the mclk clock. The maxItems will then be implicit. This is the preferred form when multiple clocks are used, and given that clocks it meant to contain a list of clocks, even if it has a single entry, placing the description in a list of items may be a bit better semantically speaking. > + > + clock-names: > + const: mclk Similarly, clock-names: items: - const: mclk Rob, is standardizing this pattern a good idea, or do you prefer the shorter form clock-names: const: mclk > + > + rst-gpios: We try to standardize GPIO names, so let's use reset-gpios. > + description: Reference to the GPIO connected to the reset pin. Active low. > + maxItems: 1 > + > + vdd-supply: > + description: Definition of the regulator used as 1.8V digital power supply. > + > + port: > + $ref: /schemas/graph.yaml#/properties/port > + additionalProperties: false > + > + properties: > + endpoint: > + $ref: /schemas/media/video-interfaces.yaml# > + unevaluatedProperties: false > + > + properties: > + data-lanes: > + oneOf: > + - items: > + - const: 1 > + - const: 2 > + - const: 3 > + - const: 4 > + - items: > + - const: 1 > + - const: 2 > + > + required: > + - data-lanes > + > +required: > + - compatible > + - reg > + - clocks > + - clock-names > + - rst-gpios > + - vdd-supply > + - port > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/gpio/gpio.h> > + > + i2c { > + #address-cells = <1>; > + #size-cells = <0>; > + > + hi846: camera@20 { > + compatible = "hynix,hi846"; > + reg = <0x20>; > + clocks = <&clk>; > + clock-names = "mclk"; > + vdd-supply = <®_camera_pwr_en>; /* 1.8v */ > + rst-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; > + > + port { > + camera_out: endpoint { > + remote-endpoint = <&csi1_ep1>; > + data-lanes = <1 2>; > + }; > + }; > + }; > + }; > + > +... -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v2 2/5] dt-bindings: media: document SK Hynix Hi-846 MIPI CSI-2 8M pixel sensor 2021-05-28 8:35 ` Laurent Pinchart @ 2021-06-02 13:52 ` Sakari Ailus 0 siblings, 0 replies; 18+ messages in thread From: Sakari Ailus @ 2021-06-02 13:52 UTC (permalink / raw) To: Laurent Pinchart Cc: Martin Kepplinger, mchehab, devicetree, kernel, krzysztof.kozlowski, linux-kernel, linux-media, paul.kocialkowski, robh, shawnx.tu On Fri, May 28, 2021 at 11:35:35AM +0300, Laurent Pinchart wrote: ... > > + maxItems: 1 > > + > > + clocks: > > + description: Reference to the mclk clock. > > + maxItems: 1 > > You could also write this > > clocks: > items: > - description: Reference to the mclk clock. > > The maxItems will then be implicit. This is the preferred form when > multiple clocks are used, and given that clocks it meant to contain a > list of clocks, even if it has a single entry, placing the description > in a list of items may be a bit better semantically speaking. > > > + > > + clock-names: > > + const: mclk > > Similarly, > > clock-names: > items: > - const: mclk > > Rob, is standardizing this pattern a good idea, or do you prefer the > shorter form > > clock-names: > const: mclk As there's just one clock, isn't the clock-names redundant? -- Sakari Ailus ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v2 2/5] dt-bindings: media: document SK Hynix Hi-846 MIPI CSI-2 8M pixel sensor 2021-05-28 8:13 ` [PATCH v2 2/5] dt-bindings: media: document SK Hynix Hi-846 MIPI CSI-2 8M pixel sensor Martin Kepplinger 2021-05-28 8:35 ` Laurent Pinchart @ 2021-06-02 13:51 ` Sakari Ailus 2021-06-02 14:05 ` Laurent Pinchart 1 sibling, 1 reply; 18+ messages in thread From: Sakari Ailus @ 2021-06-02 13:51 UTC (permalink / raw) To: Martin Kepplinger Cc: laurent.pinchart, mchehab, devicetree, kernel, krzysztof.kozlowski, linux-kernel, linux-media, paul.kocialkowski, robh, shawnx.tu Hi Martin, On Fri, May 28, 2021 at 10:13:33AM +0200, Martin Kepplinger wrote: > Document the bindings used for the SK Hynix Hi-846 CMOS camera driver. > > Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> Could you read Documentation/driver-api/media/camera-sensor.rst, please? I believe you'll need assigned-clock-rates device property as well as link-frequencies endpoint property. > --- > .../bindings/media/i2c/hynix,hi846.yaml | 99 +++++++++++++++++++ > 1 file changed, 99 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml > > diff --git a/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml > new file mode 100644 > index 000000000000..2991108e23e5 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml > @@ -0,0 +1,99 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/media/i2c/hynix,hi846.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: SK Hynix Hi-846 1/4" 8M Pixel MIPI CSI-2 sensor > + > +maintainers: > + - Martin Kepplinger <martin.kepplinger@puri.sm> > + > +description: |- > + The Hi-846 is a raw image sensor with an MIPI CSI-2 image data > + interface and CCI (I2C compatible) control bus. The output format > + is 10bit Bayer. Virtually all Bayer sensors can do 8 bpp, too. I'd drop the sentence mentoning 10 bits. > + > +properties: > + compatible: > + const: hynix,hi846 > + > + reg: > + description: I2C device address. > + maxItems: 1 > + > + clocks: > + description: Reference to the mclk clock. > + maxItems: 1 > + > + clock-names: > + const: mclk > + > + rst-gpios: > + description: Reference to the GPIO connected to the reset pin. Active low. > + maxItems: 1 > + > + vdd-supply: > + description: Definition of the regulator used as 1.8V digital power supply. > + > + port: > + $ref: /schemas/graph.yaml#/properties/port > + additionalProperties: false > + > + properties: > + endpoint: > + $ref: /schemas/media/video-interfaces.yaml# > + unevaluatedProperties: false > + > + properties: > + data-lanes: > + oneOf: > + - items: > + - const: 1 > + - const: 2 > + - const: 3 > + - const: 4 > + - items: > + - const: 1 > + - const: 2 > + > + required: > + - data-lanes > + > +required: > + - compatible > + - reg > + - clocks > + - clock-names > + - rst-gpios > + - vdd-supply > + - port > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/gpio/gpio.h> > + > + i2c { > + #address-cells = <1>; > + #size-cells = <0>; > + > + hi846: camera@20 { > + compatible = "hynix,hi846"; > + reg = <0x20>; > + clocks = <&clk>; > + clock-names = "mclk"; > + vdd-supply = <®_camera_pwr_en>; /* 1.8v */ > + rst-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; > + > + port { > + camera_out: endpoint { > + remote-endpoint = <&csi1_ep1>; > + data-lanes = <1 2>; > + }; > + }; > + }; > + }; > + > +... -- Kind regards, Sakari Ailus ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v2 2/5] dt-bindings: media: document SK Hynix Hi-846 MIPI CSI-2 8M pixel sensor 2021-06-02 13:51 ` Sakari Ailus @ 2021-06-02 14:05 ` Laurent Pinchart 2021-06-02 14:12 ` Martin Kepplinger 2021-06-02 14:37 ` Sakari Ailus 0 siblings, 2 replies; 18+ messages in thread From: Laurent Pinchart @ 2021-06-02 14:05 UTC (permalink / raw) To: Sakari Ailus Cc: Martin Kepplinger, mchehab, devicetree, kernel, krzysztof.kozlowski, linux-kernel, linux-media, paul.kocialkowski, robh, shawnx.tu On Wed, Jun 02, 2021 at 04:51:37PM +0300, Sakari Ailus wrote: > Hi Martin, > > On Fri, May 28, 2021 at 10:13:33AM +0200, Martin Kepplinger wrote: > > Document the bindings used for the SK Hynix Hi-846 CMOS camera driver. > > > > Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> > > Could you read Documentation/driver-api/media/camera-sensor.rst, please? > > I believe you'll need assigned-clock-rates device property as well as I dn't think assigned-clock-rates should be part of the bindings, it's a mechanism that can be used in any DT device node. > link-frequencies endpoint property. > > > --- > > .../bindings/media/i2c/hynix,hi846.yaml | 99 +++++++++++++++++++ > > 1 file changed, 99 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml > > > > diff --git a/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml > > new file mode 100644 > > index 000000000000..2991108e23e5 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml > > @@ -0,0 +1,99 @@ > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/media/i2c/hynix,hi846.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: SK Hynix Hi-846 1/4" 8M Pixel MIPI CSI-2 sensor > > + > > +maintainers: > > + - Martin Kepplinger <martin.kepplinger@puri.sm> > > + > > +description: |- > > + The Hi-846 is a raw image sensor with an MIPI CSI-2 image data > > + interface and CCI (I2C compatible) control bus. The output format > > + is 10bit Bayer. > > Virtually all Bayer sensors can do 8 bpp, too. I'd drop the sentence Not this one according to its datasheet (we can't rule out that this would be possible an undocumented of course). > mentoning 10 bits. > > > + > > +properties: > > + compatible: > > + const: hynix,hi846 > > + > > + reg: > > + description: I2C device address. > > + maxItems: 1 > > + > > + clocks: > > + description: Reference to the mclk clock. > > + maxItems: 1 > > + > > + clock-names: > > + const: mclk > > + > > + rst-gpios: > > + description: Reference to the GPIO connected to the reset pin. Active low. > > + maxItems: 1 > > + > > + vdd-supply: > > + description: Definition of the regulator used as 1.8V digital power supply. > > + > > + port: > > + $ref: /schemas/graph.yaml#/properties/port > > + additionalProperties: false > > + > > + properties: > > + endpoint: > > + $ref: /schemas/media/video-interfaces.yaml# > > + unevaluatedProperties: false > > + > > + properties: > > + data-lanes: > > + oneOf: > > + - items: > > + - const: 1 > > + - const: 2 > > + - const: 3 > > + - const: 4 > > + - items: > > + - const: 1 > > + - const: 2 > > + > > + required: > > + - data-lanes > > + > > +required: > > + - compatible > > + - reg > > + - clocks > > + - clock-names > > + - rst-gpios > > + - vdd-supply > > + - port > > + > > +additionalProperties: false > > + > > +examples: > > + - | > > + #include <dt-bindings/gpio/gpio.h> > > + > > + i2c { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + hi846: camera@20 { > > + compatible = "hynix,hi846"; > > + reg = <0x20>; > > + clocks = <&clk>; > > + clock-names = "mclk"; > > + vdd-supply = <®_camera_pwr_en>; /* 1.8v */ > > + rst-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; > > + > > + port { > > + camera_out: endpoint { > > + remote-endpoint = <&csi1_ep1>; > > + data-lanes = <1 2>; > > + }; > > + }; > > + }; > > + }; > > + > > +... -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v2 2/5] dt-bindings: media: document SK Hynix Hi-846 MIPI CSI-2 8M pixel sensor 2021-06-02 14:05 ` Laurent Pinchart @ 2021-06-02 14:12 ` Martin Kepplinger 2021-06-02 14:37 ` Sakari Ailus 1 sibling, 0 replies; 18+ messages in thread From: Martin Kepplinger @ 2021-06-02 14:12 UTC (permalink / raw) To: Laurent Pinchart, Sakari Ailus Cc: mchehab, devicetree, kernel, krzysztof.kozlowski, linux-kernel, linux-media, paul.kocialkowski, robh, shawnx.tu Am Mittwoch, dem 02.06.2021 um 17:05 +0300 schrieb Laurent Pinchart: > On Wed, Jun 02, 2021 at 04:51:37PM +0300, Sakari Ailus wrote: > > Hi Martin, > > > > On Fri, May 28, 2021 at 10:13:33AM +0200, Martin Kepplinger wrote: > > > Document the bindings used for the SK Hynix Hi-846 CMOS camera > > > driver. > > > > > > Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> > > > > Could you read Documentation/driver-api/media/camera-sensor.rst, > > please? > > > > I believe you'll need assigned-clock-rates device property as well > > as > > I dn't think assigned-clock-rates should be part of the bindings, > it's a > mechanism that can be used in any DT device node. > > > link-frequencies endpoint property. > > > > > --- > > > .../bindings/media/i2c/hynix,hi846.yaml | 99 > > > +++++++++++++++++++ > > > 1 file changed, 99 insertions(+) > > > create mode 100644 > > > Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml > > > > > > diff --git > > > a/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml > > > b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml > > > new file mode 100644 > > > index 000000000000..2991108e23e5 > > > --- /dev/null > > > +++ > > > b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml > > > @@ -0,0 +1,99 @@ > > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > > > +%YAML 1.2 > > > +--- > > > +$id: http://devicetree.org/schemas/media/i2c/hynix,hi846.yaml# > > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > > + > > > +title: SK Hynix Hi-846 1/4" 8M Pixel MIPI CSI-2 sensor > > > + > > > +maintainers: > > > + - Martin Kepplinger <martin.kepplinger@puri.sm> > > > + > > > +description: |- > > > + The Hi-846 is a raw image sensor with an MIPI CSI-2 image data > > > + interface and CCI (I2C compatible) control bus. The output > > > format > > > + is 10bit Bayer. > > > > Virtually all Bayer sensors can do 8 bpp, too. I'd drop the > > sentence > > Not this one according to its datasheet (we can't rule out that this > would be possible an undocumented of course). actually there is one register that mentions raw8 output but I never got that to work. I don't have to mention 10bit in this description. thanks. > > > mentoning 10 bits. > > > > > + > > > +properties: > > > + compatible: > > > + const: hynix,hi846 > > > + > > > + reg: > > > + description: I2C device address. > > > + maxItems: 1 > > > + > > > + clocks: > > > + description: Reference to the mclk clock. > > > + maxItems: 1 > > > + > > > + clock-names: > > > + const: mclk > > > + > > > + rst-gpios: > > > + description: Reference to the GPIO connected to the reset > > > pin. Active low. > > > + maxItems: 1 > > > + > > > + vdd-supply: > > > + description: Definition of the regulator used as 1.8V > > > digital power supply. > > > + > > > + port: > > > + $ref: /schemas/graph.yaml#/properties/port > > > + additionalProperties: false > > > + > > > + properties: > > > + endpoint: > > > + $ref: /schemas/media/video-interfaces.yaml# > > > + unevaluatedProperties: false > > > + > > > + properties: > > > + data-lanes: > > > + oneOf: > > > + - items: > > > + - const: 1 > > > + - const: 2 > > > + - const: 3 > > > + - const: 4 > > > + - items: > > > + - const: 1 > > > + - const: 2 > > > + > > > + required: > > > + - data-lanes > > > + > > > +required: > > > + - compatible > > > + - reg > > > + - clocks > > > + - clock-names > > > + - rst-gpios > > > + - vdd-supply > > > + - port > > > + > > > +additionalProperties: false > > > + > > > +examples: > > > + - | > > > + #include <dt-bindings/gpio/gpio.h> > > > + > > > + i2c { > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + > > > + hi846: camera@20 { > > > + compatible = "hynix,hi846"; > > > + reg = <0x20>; > > > + clocks = <&clk>; > > > + clock-names = "mclk"; > > > + vdd-supply = <®_camera_pwr_en>; /* 1.8v */ > > > + rst-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; > > > + > > > + port { > > > + camera_out: endpoint { > > > + remote-endpoint = <&csi1_ep1>; > > > + data-lanes = <1 2>; > > > + }; > > > + }; > > > + }; > > > + }; > > > + > > > +... > ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v2 2/5] dt-bindings: media: document SK Hynix Hi-846 MIPI CSI-2 8M pixel sensor 2021-06-02 14:05 ` Laurent Pinchart 2021-06-02 14:12 ` Martin Kepplinger @ 2021-06-02 14:37 ` Sakari Ailus 1 sibling, 0 replies; 18+ messages in thread From: Sakari Ailus @ 2021-06-02 14:37 UTC (permalink / raw) To: Laurent Pinchart Cc: Martin Kepplinger, mchehab, devicetree, kernel, krzysztof.kozlowski, linux-kernel, linux-media, paul.kocialkowski, robh, shawnx.tu Hi Laurent, On Wed, Jun 02, 2021 at 05:05:14PM +0300, Laurent Pinchart wrote: > On Wed, Jun 02, 2021 at 04:51:37PM +0300, Sakari Ailus wrote: > > Hi Martin, > > > > On Fri, May 28, 2021 at 10:13:33AM +0200, Martin Kepplinger wrote: > > > Document the bindings used for the SK Hynix Hi-846 CMOS camera driver. > > > > > > Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> > > > > Could you read Documentation/driver-api/media/camera-sensor.rst, please? > > > > I believe you'll need assigned-clock-rates device property as well as > > I dn't think assigned-clock-rates should be part of the bindings, it's a > mechanism that can be used in any DT device node. What if it's required? > > > link-frequencies endpoint property. > > > > > --- > > > .../bindings/media/i2c/hynix,hi846.yaml | 99 +++++++++++++++++++ > > > 1 file changed, 99 insertions(+) > > > create mode 100644 Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml > > > > > > diff --git a/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml > > > new file mode 100644 > > > index 000000000000..2991108e23e5 > > > --- /dev/null > > > +++ b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml > > > @@ -0,0 +1,99 @@ > > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > > > +%YAML 1.2 > > > +--- > > > +$id: http://devicetree.org/schemas/media/i2c/hynix,hi846.yaml# > > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > > + > > > +title: SK Hynix Hi-846 1/4" 8M Pixel MIPI CSI-2 sensor > > > + > > > +maintainers: > > > + - Martin Kepplinger <martin.kepplinger@puri.sm> > > > + > > > +description: |- > > > + The Hi-846 is a raw image sensor with an MIPI CSI-2 image data > > > + interface and CCI (I2C compatible) control bus. The output format > > > + is 10bit Bayer. > > > > Virtually all Bayer sensors can do 8 bpp, too. I'd drop the sentence > > Not this one according to its datasheet (we can't rule out that this > would be possible an undocumented of course). Ok, fair enough. > > > mentoning 10 bits. > > > > > + > > > +properties: > > > + compatible: > > > + const: hynix,hi846 > > > + > > > + reg: > > > + description: I2C device address. > > > + maxItems: 1 > > > + > > > + clocks: > > > + description: Reference to the mclk clock. > > > + maxItems: 1 > > > + > > > + clock-names: > > > + const: mclk > > > + > > > + rst-gpios: > > > + description: Reference to the GPIO connected to the reset pin. Active low. > > > + maxItems: 1 > > > + > > > + vdd-supply: > > > + description: Definition of the regulator used as 1.8V digital power supply. > > > + > > > + port: > > > + $ref: /schemas/graph.yaml#/properties/port > > > + additionalProperties: false > > > + > > > + properties: > > > + endpoint: > > > + $ref: /schemas/media/video-interfaces.yaml# > > > + unevaluatedProperties: false > > > + > > > + properties: > > > + data-lanes: > > > + oneOf: > > > + - items: > > > + - const: 1 > > > + - const: 2 > > > + - const: 3 > > > + - const: 4 > > > + - items: > > > + - const: 1 > > > + - const: 2 > > > + > > > + required: > > > + - data-lanes > > > + > > > +required: > > > + - compatible > > > + - reg > > > + - clocks > > > + - clock-names > > > + - rst-gpios > > > + - vdd-supply > > > + - port > > > + > > > +additionalProperties: false > > > + > > > +examples: > > > + - | > > > + #include <dt-bindings/gpio/gpio.h> > > > + > > > + i2c { > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + > > > + hi846: camera@20 { > > > + compatible = "hynix,hi846"; > > > + reg = <0x20>; > > > + clocks = <&clk>; > > > + clock-names = "mclk"; > > > + vdd-supply = <®_camera_pwr_en>; /* 1.8v */ > > > + rst-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; > > > + > > > + port { > > > + camera_out: endpoint { > > > + remote-endpoint = <&csi1_ep1>; > > > + data-lanes = <1 2>; > > > + }; > > > + }; > > > + }; > > > + }; > > > + > > > +... > > -- > Regards, > > Laurent Pinchart -- Sakari Ailus ^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v2 3/5] media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera 2021-05-28 8:13 [PATCH v2 0/5] Add support for the Hynix Hi-846 camera Martin Kepplinger 2021-05-28 8:13 ` [PATCH v2 1/5] dt-bindings: vendor-prefixes: Add SK Hynix Inc Martin Kepplinger 2021-05-28 8:13 ` [PATCH v2 2/5] dt-bindings: media: document SK Hynix Hi-846 MIPI CSI-2 8M pixel sensor Martin Kepplinger @ 2021-05-28 8:13 ` Martin Kepplinger 2021-05-28 18:20 ` kernel test robot ` (2 more replies) 2021-05-28 8:13 ` [PATCH v2 4/5] arm64: defconfig: enable VIDEO_HI846 Martin Kepplinger ` (2 subsequent siblings) 5 siblings, 3 replies; 18+ messages in thread From: Martin Kepplinger @ 2021-05-28 8:13 UTC (permalink / raw) To: laurent.pinchart, mchehab Cc: devicetree, kernel, krzysztof.kozlowski, linux-kernel, linux-media, paul.kocialkowski, robh, shawnx.tu, Martin Kepplinger The SK Hynix Hi-846 is a 1/4" 8M Pixel CMOS Image Sensor. It supports usual features like I2C control, CSI-2 for frame data, digital/analog gain control or test patterns. This driver supports the 640x480, 1280x720 and 1632x1224 resolution modes. It supports runtime PM in order not to draw any unnecessary power. The part is also called YACG4D0C9SHC and a datasheet can be found at https://product.skhynix.com/products/cis/cis.go The large sets of partly undocumented register values are for example found when searching for the hi846_mipi_raw_Sensor.c Android driver. Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> --- MAINTAINERS | 6 + drivers/media/i2c/Kconfig | 13 + drivers/media/i2c/Makefile | 1 + drivers/media/i2c/hi846.c | 2137 ++++++++++++++++++++++++++++++++++++ 4 files changed, 2157 insertions(+) create mode 100644 drivers/media/i2c/hi846.c diff --git a/MAINTAINERS b/MAINTAINERS index 81e1edeceae4..b5ec5c66ec0e 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -8425,6 +8425,12 @@ S: Maintained T: git git://linuxtv.org/media_tree.git F: drivers/media/i2c/hi556.c +HYNIX HI846 SENSOR DRIVER +M: Martin Kepplinger <martin.kepplinger@puri.sm> +L: linux-media@vger.kernel.org +S: Maintained +F: drivers/media/i2c/hi846.c + Hyper-V/Azure CORE AND DRIVERS M: "K. Y. Srinivasan" <kys@microsoft.com> M: Haiyang Zhang <haiyangz@microsoft.com> diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig index 462c0e059754..f8cf5bf8eb68 100644 --- a/drivers/media/i2c/Kconfig +++ b/drivers/media/i2c/Kconfig @@ -738,6 +738,19 @@ config VIDEO_HI556 To compile this driver as a module, choose M here: the module will be called hi556. +config VIDEO_HI846 + tristate "Hynix Hi-846 sensor support" + depends on I2C && VIDEO_V4L2 + select MEDIA_CONTROLLER + select VIDEO_V4L2_SUBDEV_API + select V4L2_FWNODE + help + This is a Video4Linux2 sensor driver for the Hynix + Hi-846 camera. + + To compile this driver as a module, choose M here: the + module will be called hi846. + config VIDEO_IMX214 tristate "Sony IMX214 sensor support" depends on GPIOLIB && I2C && VIDEO_V4L2 diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile index 0c067beca066..1194c5e6708b 100644 --- a/drivers/media/i2c/Makefile +++ b/drivers/media/i2c/Makefile @@ -116,6 +116,7 @@ obj-$(CONFIG_VIDEO_ML86V7667) += ml86v7667.o obj-$(CONFIG_VIDEO_OV2659) += ov2659.o obj-$(CONFIG_VIDEO_TC358743) += tc358743.o obj-$(CONFIG_VIDEO_HI556) += hi556.o +obj-$(CONFIG_VIDEO_HI846) += hi846.o obj-$(CONFIG_VIDEO_IMX214) += imx214.o obj-$(CONFIG_VIDEO_IMX219) += imx219.o obj-$(CONFIG_VIDEO_IMX258) += imx258.o diff --git a/drivers/media/i2c/hi846.c b/drivers/media/i2c/hi846.c new file mode 100644 index 000000000000..3f896e45f99a --- /dev/null +++ b/drivers/media/i2c/hi846.c @@ -0,0 +1,2137 @@ +// SPDX-License-Identifier: GPL-2.0 +// Copyright (c) 2021 Purism SPC + +#include <asm/unaligned.h> +#include <linux/clk.h> +#include <linux/delay.h> +#include <linux/gpio.h> +#include <linux/i2c.h> +#include <linux/module.h> +#include <linux/of_gpio.h> +#include <linux/of_graph.h> +#include <linux/regulator/consumer.h> +#include <linux/pm_runtime.h> +#include <linux/pm.h> +#include <media/v4l2-ctrls.h> +#include <media/v4l2-device.h> +#include <media/v4l2-fwnode.h> + + +#define HI846_MEDIA_BUS_FORMAT MEDIA_BUS_FMT_SGBRG10_1X10 +#define HI846_RGB_DEPTH 10 +#define DEFAULT_FPS 30 + +/* Frame length lines / Vertical timings */ +#define HI846_REG_FLL 0x0006 +#define HI846_FLL_MAX 0xffff + +/* Horizontal timing */ +#define HI846_REG_LLP 0x0008 +#define HI846_LINE_LENGTH 3800 + +#define HI846_REG_BINNING_MODE 0x000c + +#define HI846_REG_IMAGE_ORIENTATION 0x000e + +#define HI846_REG_UNKNOWN_0022 0x0022 + +#define HI846_REG_Y_ADDR_START_VACT_H 0x0026 +#define HI846_REG_Y_ADDR_START_VACT_L 0x0027 +#define HI846_REG_UNKNOWN_0028 0x0028 + +#define HI846_REG_Y_ADDR_END_VACT_H 0x002c +#define HI846_REG_Y_ADDR_END_VACT_L 0x002d + +#define HI846_REG_Y_ODD_INC_FOBP 0x002e +#define HI846_REG_Y_EVEN_INC_FOBP 0x002f + +#define HI846_REG_Y_ODD_INC_VACT 0x0032 +#define HI846_REG_Y_EVEN_INC_VACT 0x0033 + +#define HI846_REG_GROUPED_PARA_HOLD 0x0046 + +#define HI846_REG_TG_ENABLE 0x004c + +#define HI846_REG_UNKNOWN_005C 0x005c + +#define HI846_REG_UNKNOWN_006A 0x006a + +/* Long exposure time. Actually, exposure is a 20 bit value that + * includes the lower 4 bits of 0x0073 too. only 16 bit are used + * right now + */ +#define HI846_REG_EXPOSURE 0x0074 +#define HI846_EXPOSURE_MIN 6 +#define HI846_EXPOSURE_MAX_MARGIN 2 +#define HI846_EXPOSURE_STEP 1 + +/* Analog gain controls from sensor */ +#define HI846_REG_ANALOG_GAIN 0x0077 +#define HI846_ANAL_GAIN_MIN 0 +#define HI846_ANAL_GAIN_MAX 240 +#define HI846_ANAL_GAIN_STEP 8 + +/* Digital gain controls from sensor */ +#define HI846_REG_MWB_GR_GAIN_H 0x0078 +#define HI846_REG_MWB_GR_GAIN_L 0x0079 +#define HI846_REG_MWB_GB_GAIN_H 0x007a +#define HI846_REG_MWB_GB_GAIN_L 0x007b +#define HI846_REG_MWB_R_GAIN_H 0x007c +#define HI846_REG_MWB_R_GAIN_L 0x007d +#define HI846_REG_MWB_B_GAIN_H 0x007e +#define HI846_REG_MWB_B_GAIN_L 0x007f +#define HI846_DGTL_GAIN_MIN 0 +#define HI846_DGTL_GAIN_MAX 8191 +#define HI846_DGTL_GAIN_STEP 1 +#define HI846_DGTL_GAIN_DEFAULT 256 + +#define HI846_REG_X_ADDR_START_HACT_H 0x0120 +#define HI846_REG_X_ADDR_END_HACT_H 0x0122 + +#define HI846_REG_UNKNOWN_012A 0x012a + +#define HI846_REG_UNKNOWN_0200 0x0200 + +#define HI846_REG_UNKNOWN_021C 0x021c +#define HI846_REG_UNKNOWN_021E 0x021e + +#define HI846_REG_UNKNOWN_0402 0x0402 +#define HI846_REG_UNKNOWN_0404 0x0404 +#define HI846_REG_UNKNOWN_0408 0x0408 +#define HI846_REG_UNKNOWN_0410 0x0410 +#define HI846_REG_UNKNOWN_0412 0x0412 +#define HI846_REG_UNKNOWN_0414 0x0414 + +#define HI846_REG_UNKNOWN_0418 0x0418 + +#define HI846_REG_UNKNOWN_051E 0x051e + +/* Formatter */ +#define HI846_REG_X_START_H 0x0804 +#define HI846_REG_X_START_L 0x0805 + +/* MIPI */ +#define HI846_REG_UNKNOWN_0900 0x0900 +#define HI846_REG_MIPI_TX_OP_EN 0x0901 +#define HI846_REG_MIPI_TX_OP_MODE 0x0902 +#define HI846_RAW8 BIT(5) + +#define HI846_REG_UNKNOWN_090C 0x090c +#define HI846_REG_UNKNOWN_090E 0x090e + +#define HI846_REG_UNKNOWN_0914 0x0914 +#define HI846_REG_TLPX 0x0915 +#define HI846_REG_TCLK_PREPARE 0x0916 +#define HI846_REG_TCLK_ZERO 0x0917 +#define HI846_REG_UNKNOWN_0918 0x0918 +#define HI846_REG_THS_PREPARE 0x0919 +#define HI846_REG_THS_ZERO 0x091a +#define HI846_REG_THS_TRAIL 0x091b +#define HI846_REG_TCLK_POST 0x091c +#define HI846_REG_TCLK_TRAIL_MIN 0x091d +#define HI846_REG_UNKNOWN_091E 0x091e + +#define HI846_REG_UNKNOWN_0954 0x0954 +#define HI846_REG_UNKNOWN_0956 0x0956 +#define HI846_REG_UNKNOWN_0958 0x0958 +#define HI846_REG_UNKNOWN_095A 0x095a + +/* ISP Common */ +#define HI846_REG_MODE_SELECT 0x0a00 +#define HI846_MODE_STANDBY 0x00 +#define HI846_MODE_STREAMING 0x01 +#define HI846_REG_FAST_STANDBY_MODE 0x0a02 +#define HI846_REG_ISP_EN_H 0x0a04 + +/* Test Pattern Control */ +#define HI846_REG_ISP 0x0a05 +#define HI846_REG_ISP_TPG_EN 0x01 +#define HI846_REG_TEST_PATTERN 0x020a /* 1-9 */ + +#define HI846_REG_UNKNOWN_0A0C 0x0a0c + +/* Windowing */ +#define HI846_REG_X_OUTPUT_SIZE_H 0x0a12 +#define HI846_REG_X_OUTPUT_SIZE_L 0x0a13 +#define HI846_REG_Y_OUTPUT_SIZE_H 0x0a14 +#define HI846_REG_Y_OUTPUT_SIZE_L 0x0a15 + +/* ISP Common */ +#define HI846_REG_PEDESTAL_EN 0x0a1a + +#define HI846_REG_UNKNOWN_0A1E 0x0a1e + +/* Horizontal Binning Mode */ +#define HI846_REG_HBIN_MODE 0x0a22 + +#define HI846_REG_UNKNOWN_0A24 0x0a24 +#define HI846_REG_UNKNOWN_0B02 0x0b02 +#define HI846_REG_UNKNOWN_0B10 0x0b10 +#define HI846_REG_UNKNOWN_0B12 0x0b12 +#define HI846_REG_UNKNOWN_0B14 0x0b14 + +/* BLC (Black Level Calibration) */ +#define HI846_REG_BLC_CTL0 0x0c00 + +#define HI846_REG_UNKNOWN_0C06 0x0c06 +#define HI846_REG_UNKNOWN_0C10 0x0c10 +#define HI846_REG_UNKNOWN_0C12 0x0c12 +#define HI846_REG_UNKNOWN_0C14 0x0c14 +#define HI846_REG_UNKNOWN_0C16 0x0c16 + +#define HI846_REG_UNKNOWN_0E04 0x0e04 + +#define HI846_REG_CHIP_ID_L 0x0f16 +#define HI846_REG_CHIP_ID_H 0x0f17 +#define HI846_CHIP_ID_L 0x46 +#define HI846_CHIP_ID_H 0x08 + +#define HI846_REG_UNKNOWN_0F04 0x0f04 +#define HI846_REG_UNKNOWN_0F08 0x0f08 + +/* PLL */ +#define HI846_REG_PLL_CFG_MIPI2_H 0x0f2a +#define HI846_REG_PLL_CFG_MIPI2_L 0x0f2b + +#define HI846_REG_UNKNOWN_0F30 0x0f30 +#define HI846_REG_PLL_CFG_RAMP1_H 0x0f32 +#define HI846_REG_UNKNOWN_0F36 0x0f36 +#define HI846_REG_PLL_CFG_MIPI1_H 0x0f38 + +#define HI846_REG_UNKNOWN_2008 0x2008 +#define HI846_REG_UNKNOWN_326E 0x326e + +struct hi846_reg { + u16 address; + u16 val; +}; + +struct hi846_reg_list { + u32 num_of_regs; + const struct hi846_reg *regs; +}; + +struct hi846_mode { + /* Frame width in pixels */ + u32 width; + + /* Frame height in pixels */ + u32 height; + + /* Horizontal timing size */ + u32 llp; + + /* Link frequency needed for this resolution */ + u8 link_freq_index; + + u16 fps; + + /* vertical timining size */ + u16 frame_len; + + const struct hi846_reg_list reg_list_config; + const struct hi846_reg_list reg_list_2lane; + const struct hi846_reg_list reg_list_4lane; +}; + +#define to_hi846(_sd) container_of(_sd, struct hi846, sd) + +static const struct hi846_reg hi846_init_2lane[] = { + {HI846_REG_MODE_SELECT, 0x0000}, + /* regs below are unknown */ + {0x2000, 0x100A}, + {0x2002, 0x00FF}, + {0x2004, 0x0007}, + {0x2006, 0x3FFF}, + {0x2008, 0x3FFF}, + {0x200A, 0xC216}, + {0x200C, 0x1292}, + {0x200E, 0xC01A}, + {0x2010, 0x403D}, + {0x2012, 0x000E}, + {0x2014, 0x403E}, + {0x2016, 0x0B80}, + {0x2018, 0x403F}, + {0x201A, 0x82AE}, + {0x201C, 0x1292}, + {0x201E, 0xC00C}, + {0x2020, 0x4130}, + {0x2022, 0x43E2}, + {0x2024, 0x0180}, + {0x2026, 0x4130}, + {0x2028, 0x7400}, + {0x202A, 0x5000}, + {0x202C, 0x0253}, + {0x202E, 0x0AD1}, + {0x2030, 0x2360}, + {0x2032, 0x0009}, + {0x2034, 0x5020}, + {0x2036, 0x000B}, + {0x2038, 0x0002}, + {0x203A, 0x0044}, + {0x203C, 0x0016}, + {0x203E, 0x1792}, + {0x2040, 0x7002}, + {0x2042, 0x154F}, + {0x2044, 0x00D5}, + {0x2046, 0x000B}, + {0x2048, 0x0019}, + {0x204A, 0x1698}, + {0x204C, 0x000E}, + {0x204E, 0x099A}, + {0x2050, 0x0058}, + {0x2052, 0x7000}, + {0x2054, 0x1799}, + {0x2056, 0x0310}, + {0x2058, 0x03C3}, + {0x205A, 0x004C}, + {0x205C, 0x064A}, + {0x205E, 0x0001}, + {0x2060, 0x0007}, + {0x2062, 0x0BC7}, + {0x2064, 0x0055}, + {0x2066, 0x7000}, + {0x2068, 0x1550}, + {0x206A, 0x158A}, + {0x206C, 0x0004}, + {0x206E, 0x1488}, + {0x2070, 0x7010}, + {0x2072, 0x1508}, + {0x2074, 0x0004}, + {0x2076, 0x0016}, + {0x2078, 0x03D5}, + {0x207A, 0x0055}, + {0x207C, 0x08CA}, + {0x207E, 0x2019}, + {0x2080, 0x0007}, + {0x2082, 0x7057}, + {0x2084, 0x0FC7}, + {0x2086, 0x5041}, + {0x2088, 0x12C8}, + {0x208A, 0x5060}, + {0x208C, 0x5080}, + {0x208E, 0x2084}, + {0x2090, 0x12C8}, + {0x2092, 0x7800}, + {0x2094, 0x0802}, + {0x2096, 0x040F}, + {0x2098, 0x1007}, + {0x209A, 0x0803}, + {0x209C, 0x080B}, + {0x209E, 0x3803}, + {0x20A0, 0x0807}, + {0x20A2, 0x0404}, + {0x20A4, 0x0400}, + {0x20A6, 0xFFFF}, + {0x20A8, 0xF0B2}, + {0x20AA, 0xFFEF}, + {0x20AC, 0x0A84}, + {0x20AE, 0x1292}, + {0x20B0, 0xC02E}, + {0x20B2, 0x4130}, + {0x23FE, 0xC056}, + {0x3232, 0xFC0C}, + {0x3236, 0xFC22}, + {0x3248, 0xFCA8}, + {0x326A, 0x8302}, + {0x326C, 0x830A}, + {0x326E, 0x0000}, + {0x32CA, 0xFC28}, + {0x32CC, 0xC3BC}, + {0x32CE, 0xC34C}, + {0x32D0, 0xC35A}, + {0x32D2, 0xC368}, + {0x32D4, 0xC376}, + {0x32D6, 0xC3C2}, + {0x32D8, 0xC3E6}, + {0x32DA, 0x0003}, + {0x32DC, 0x0003}, + {0x32DE, 0x00C7}, + {0x32E0, 0x0031}, + {0x32E2, 0x0031}, + {0x32E4, 0x0031}, + {0x32E6, 0xFC28}, + {0x32E8, 0xC3BC}, + {0x32EA, 0xC384}, + {0x32EC, 0xC392}, + {0x32EE, 0xC3A0}, + {0x32F0, 0xC3AE}, + {0x32F2, 0xC3C4}, + {0x32F4, 0xC3E6}, + {0x32F6, 0x0003}, + {0x32F8, 0x0003}, + {0x32FA, 0x00C7}, + {0x32FC, 0x0031}, + {0x32FE, 0x0031}, + {0x3300, 0x0031}, + {0x3302, 0x82CA}, + {0x3304, 0xC164}, + {0x3306, 0x82E6}, + {0x3308, 0xC19C}, + {0x330A, 0x001F}, + {0x330C, 0x001A}, + {0x330E, 0x0034}, + {0x3310, 0x0000}, + {0x3312, 0x0000}, + {0x3314, 0xFC94}, + {0x3316, 0xC3D8}, + /* regs above are unknown */ + {HI846_REG_MODE_SELECT, 0x0000}, + {HI846_REG_UNKNOWN_0E04, 0x0012}, + {HI846_REG_Y_ODD_INC_FOBP, 0x1111}, + {HI846_REG_Y_ODD_INC_VACT, 0x1111}, + {HI846_REG_UNKNOWN_0022, 0x0008}, + {HI846_REG_Y_ADDR_START_VACT_H, 0x0040}, + {HI846_REG_UNKNOWN_0028, 0x0017}, + {HI846_REG_Y_ADDR_END_VACT_H, 0x09CF}, + {HI846_REG_UNKNOWN_005C, 0x2101}, + {HI846_REG_FLL, 0x09DE}, + {HI846_REG_LLP, 0x0ED8}, + {HI846_REG_IMAGE_ORIENTATION, 0x0100}, + {HI846_REG_BINNING_MODE, 0x0022}, + {HI846_REG_HBIN_MODE, 0x0000}, + {HI846_REG_UNKNOWN_0A24, 0x0000}, + {HI846_REG_X_START_H, 0x0000}, + {HI846_REG_X_OUTPUT_SIZE_H, 0x0CC0}, + {HI846_REG_Y_OUTPUT_SIZE_H, 0x0990}, + {HI846_REG_EXPOSURE, 0x09D8}, + {HI846_REG_ANALOG_GAIN, 0x0000}, + {HI846_REG_GROUPED_PARA_HOLD, 0x0000}, + {HI846_REG_UNKNOWN_051E, 0x0000}, + {HI846_REG_UNKNOWN_0200, 0x0400}, + {HI846_REG_PEDESTAL_EN, 0x0C00}, + {HI846_REG_UNKNOWN_0A0C, 0x0010}, + {HI846_REG_UNKNOWN_0A1E, 0x0CCF}, + {HI846_REG_UNKNOWN_0402, 0x0110}, + {HI846_REG_UNKNOWN_0404, 0x00F4}, + {HI846_REG_UNKNOWN_0408, 0x0000}, + {HI846_REG_UNKNOWN_0410, 0x008D}, + {HI846_REG_UNKNOWN_0412, 0x011A}, + {HI846_REG_UNKNOWN_0414, 0x864C}, + {HI846_REG_UNKNOWN_021C, 0x0003}, + {HI846_REG_UNKNOWN_021E, 0x0235}, + {HI846_REG_BLC_CTL0, 0x9150}, + {HI846_REG_UNKNOWN_0C06, 0x0021}, + {HI846_REG_UNKNOWN_0C10, 0x0040}, + {HI846_REG_UNKNOWN_0C12, 0x0040}, + {HI846_REG_UNKNOWN_0C14, 0x0040}, + {HI846_REG_UNKNOWN_0C16, 0x0040}, + {HI846_REG_FAST_STANDBY_MODE, 0x0100}, + {HI846_REG_ISP_EN_H, 0x014A}, + {HI846_REG_UNKNOWN_0418, 0x0000}, + {HI846_REG_UNKNOWN_012A, 0x03B4}, + {HI846_REG_X_ADDR_START_HACT_H, 0x0046}, + {HI846_REG_X_ADDR_END_HACT_H, 0x0376}, + {HI846_REG_UNKNOWN_0B02, 0xE04D}, + {HI846_REG_UNKNOWN_0B10, 0x6821}, + {HI846_REG_UNKNOWN_0B12, 0x0120}, + {HI846_REG_UNKNOWN_0B14, 0x0001}, + {HI846_REG_UNKNOWN_2008, 0x38FD}, + {HI846_REG_UNKNOWN_326E, 0x0000}, + {HI846_REG_UNKNOWN_0900, 0x0320}, + {HI846_REG_MIPI_TX_OP_MODE, 0xC31A}, + {HI846_REG_UNKNOWN_0914, 0xC109}, + {HI846_REG_TCLK_PREPARE, 0x061A}, + {HI846_REG_UNKNOWN_0918, 0x0306}, + {HI846_REG_THS_ZERO, 0x0B09}, + {HI846_REG_TCLK_POST, 0x0C07}, + {HI846_REG_UNKNOWN_091E, 0x0A00}, + {HI846_REG_UNKNOWN_090C, 0x042A}, + {HI846_REG_UNKNOWN_090E, 0x006B}, + {HI846_REG_UNKNOWN_0954, 0x0089}, + {HI846_REG_UNKNOWN_0956, 0x0000}, + {HI846_REG_UNKNOWN_0958, 0xCA00}, + {HI846_REG_UNKNOWN_095A, 0x9240}, + {HI846_REG_UNKNOWN_0F08, 0x2F04}, + {HI846_REG_UNKNOWN_0F30, 0x001F}, + {HI846_REG_UNKNOWN_0F36, 0x001F}, + {HI846_REG_UNKNOWN_0F04, 0x3A00}, + {HI846_REG_PLL_CFG_RAMP1_H, 0x025A}, + {HI846_REG_PLL_CFG_MIPI1_H, 0x025A}, + {HI846_REG_PLL_CFG_MIPI2_H, 0x0024}, + {HI846_REG_UNKNOWN_006A, 0x0100}, + {HI846_REG_TG_ENABLE, 0x0100}, +}; + +static const struct hi846_reg hi846_init_4lane[] = { + {0x2000, 0x987A}, + {0x2002, 0x00FF}, + {0x2004, 0x0047}, + {0x2006, 0x3FFF}, + {0x2008, 0x3FFF}, + {0x200A, 0xC216}, + {0x200C, 0x1292}, + {0x200E, 0xC01A}, + {0x2010, 0x403D}, + {0x2012, 0x000E}, + {0x2014, 0x403E}, + {0x2016, 0x0B80}, + {0x2018, 0x403F}, + {0x201A, 0x82AE}, + {0x201C, 0x1292}, + {0x201E, 0xC00C}, + {0x2020, 0x4130}, + {0x2022, 0x43E2}, + {0x2024, 0x0180}, + {0x2026, 0x4130}, + {0x2028, 0x7400}, + {0x202A, 0x5000}, + {0x202C, 0x0253}, + {0x202E, 0x0AD1}, + {0x2030, 0x2360}, + {0x2032, 0x0009}, + {0x2034, 0x5020}, + {0x2036, 0x000B}, + {0x2038, 0x0002}, + {0x203A, 0x0044}, + {0x203C, 0x0016}, + {0x203E, 0x1792}, + {0x2040, 0x7002}, + {0x2042, 0x154F}, + {0x2044, 0x00D5}, + {0x2046, 0x000B}, + {0x2048, 0x0019}, + {0x204A, 0x1698}, + {0x204C, 0x000E}, + {0x204E, 0x099A}, + {0x2050, 0x0058}, + {0x2052, 0x7000}, + {0x2054, 0x1799}, + {0x2056, 0x0310}, + {0x2058, 0x03C3}, + {0x205A, 0x004C}, + {0x205C, 0x064A}, + {0x205E, 0x0001}, + {0x2060, 0x0007}, + {0x2062, 0x0BC7}, + {0x2064, 0x0055}, + {0x2066, 0x7000}, + {0x2068, 0x1550}, + {0x206A, 0x158A}, + {0x206C, 0x0004}, + {0x206E, 0x1488}, + {0x2070, 0x7010}, + {0x2072, 0x1508}, + {0x2074, 0x0004}, + {0x2076, 0x0016}, + {0x2078, 0x03D5}, + {0x207A, 0x0055}, + {0x207C, 0x08CA}, + {0x207E, 0x2019}, + {0x2080, 0x0007}, + {0x2082, 0x7057}, + {0x2084, 0x0FC7}, + {0x2086, 0x5041}, + {0x2088, 0x12C8}, + {0x208A, 0x5060}, + {0x208C, 0x5080}, + {0x208E, 0x2084}, + {0x2090, 0x12C8}, + {0x2092, 0x7800}, + {0x2094, 0x0802}, + {0x2096, 0x040F}, + {0x2098, 0x1007}, + {0x209A, 0x0803}, + {0x209C, 0x080B}, + {0x209E, 0x3803}, + {0x20A0, 0x0807}, + {0x20A2, 0x0404}, + {0x20A4, 0x0400}, + {0x20A6, 0xFFFF}, + {0x20A8, 0xF0B2}, + {0x20AA, 0xFFEF}, + {0x20AC, 0x0A84}, + {0x20AE, 0x1292}, + {0x20B0, 0xC02E}, + {0x20B2, 0x4130}, + {0x20B4, 0xF0B2}, + {0x20B6, 0xFFBF}, + {0x20B8, 0x2004}, + {0x20BA, 0x403F}, + {0x20BC, 0x00C3}, + {0x20BE, 0x4FE2}, + {0x20C0, 0x8318}, + {0x20C2, 0x43CF}, + {0x20C4, 0x0000}, + {0x20C6, 0x9382}, + {0x20C8, 0xC314}, + {0x20CA, 0x2003}, + {0x20CC, 0x12B0}, + {0x20CE, 0xCAB0}, + {0x20D0, 0x4130}, + {0x20D2, 0x12B0}, + {0x20D4, 0xC90A}, + {0x20D6, 0x4130}, + {0x20D8, 0x42D2}, + {0x20DA, 0x8318}, + {0x20DC, 0x00C3}, + {0x20DE, 0x9382}, + {0x20E0, 0xC314}, + {0x20E2, 0x2009}, + {0x20E4, 0x120B}, + {0x20E6, 0x120A}, + {0x20E8, 0x1209}, + {0x20EA, 0x1208}, + {0x20EC, 0x1207}, + {0x20EE, 0x1206}, + {0x20F0, 0x4030}, + {0x20F2, 0xC15E}, + {0x20F4, 0x4130}, + {0x20F6, 0x1292}, + {0x20F8, 0xC008}, + {0x20FA, 0x4130}, + {0x20FC, 0x42D2}, + {0x20FE, 0x82A1}, + {0x2100, 0x00C2}, + {0x2102, 0x1292}, + {0x2104, 0xC040}, + {0x2106, 0x4130}, + {0x2108, 0x1292}, + {0x210A, 0xC006}, + {0x210C, 0x42A2}, + {0x210E, 0x7324}, + {0x2110, 0x9382}, + {0x2112, 0xC314}, + {0x2114, 0x2011}, + {0x2116, 0x425F}, + {0x2118, 0x82A1}, + {0x211A, 0xF25F}, + {0x211C, 0x00C1}, + {0x211E, 0xF35F}, + {0x2120, 0x2406}, + {0x2122, 0x425F}, + {0x2124, 0x00C0}, + {0x2126, 0xF37F}, + {0x2128, 0x522F}, + {0x212A, 0x4F82}, + {0x212C, 0x7324}, + {0x212E, 0x425F}, + {0x2130, 0x82D4}, + {0x2132, 0xF35F}, + {0x2134, 0x4FC2}, + {0x2136, 0x01B3}, + {0x2138, 0x93C2}, + {0x213A, 0x829F}, + {0x213C, 0x2421}, + {0x213E, 0x403E}, + {0x2140, 0xFFFE}, + {0x2142, 0x40B2}, + {0x2144, 0xEC78}, + {0x2146, 0x831C}, + {0x2148, 0x40B2}, + {0x214A, 0xEC78}, + {0x214C, 0x831E}, + {0x214E, 0x40B2}, + {0x2150, 0xEC78}, + {0x2152, 0x8320}, + {0x2154, 0xB3D2}, + {0x2156, 0x008C}, + {0x2158, 0x2405}, + {0x215A, 0x4E0F}, + {0x215C, 0x503F}, + {0x215E, 0xFFD8}, + {0x2160, 0x4F82}, + {0x2162, 0x831C}, + {0x2164, 0x90F2}, + {0x2166, 0x0003}, + {0x2168, 0x008C}, + {0x216A, 0x2401}, + {0x216C, 0x4130}, + {0x216E, 0x421F}, + {0x2170, 0x831C}, + {0x2172, 0x5E0F}, + {0x2174, 0x4F82}, + {0x2176, 0x831E}, + {0x2178, 0x5E0F}, + {0x217A, 0x4F82}, + {0x217C, 0x8320}, + {0x217E, 0x3FF6}, + {0x2180, 0x432E}, + {0x2182, 0x3FDF}, + {0x2184, 0x421F}, + {0x2186, 0x7100}, + {0x2188, 0x4F0E}, + {0x218A, 0x503E}, + {0x218C, 0xFFD8}, + {0x218E, 0x4E82}, + {0x2190, 0x7A04}, + {0x2192, 0x421E}, + {0x2194, 0x831C}, + {0x2196, 0x5F0E}, + {0x2198, 0x4E82}, + {0x219A, 0x7A06}, + {0x219C, 0x0B00}, + {0x219E, 0x7304}, + {0x21A0, 0x0050}, + {0x21A2, 0x40B2}, + {0x21A4, 0xD081}, + {0x21A6, 0x0B88}, + {0x21A8, 0x421E}, + {0x21AA, 0x831E}, + {0x21AC, 0x5F0E}, + {0x21AE, 0x4E82}, + {0x21B0, 0x7A0E}, + {0x21B2, 0x521F}, + {0x21B4, 0x8320}, + {0x21B6, 0x4F82}, + {0x21B8, 0x7A10}, + {0x21BA, 0x0B00}, + {0x21BC, 0x7304}, + {0x21BE, 0x007A}, + {0x21C0, 0x40B2}, + {0x21C2, 0x0081}, + {0x21C4, 0x0B88}, + {0x21C6, 0x4392}, + {0x21C8, 0x7A0A}, + {0x21CA, 0x0800}, + {0x21CC, 0x7A0C}, + {0x21CE, 0x0B00}, + {0x21D0, 0x7304}, + {0x21D2, 0x022B}, + {0x21D4, 0x40B2}, + {0x21D6, 0xD081}, + {0x21D8, 0x0B88}, + {0x21DA, 0x0B00}, + {0x21DC, 0x7304}, + {0x21DE, 0x0255}, + {0x21E0, 0x40B2}, + {0x21E2, 0x0081}, + {0x21E4, 0x0B88}, + {0x21E6, 0x4130}, + {0x23FE, 0xC056}, + {0x3232, 0xFC0C}, + {0x3236, 0xFC22}, + {0x3238, 0xFCFC}, + {0x323A, 0xFD84}, + {0x323C, 0xFD08}, + {0x3246, 0xFCD8}, + {0x3248, 0xFCA8}, + {0x324E, 0xFCB4}, + {0x326A, 0x8302}, + {0x326C, 0x830A}, + {0x326E, 0x0000}, + {0x32CA, 0xFC28}, + {0x32CC, 0xC3BC}, + {0x32CE, 0xC34C}, + {0x32D0, 0xC35A}, + {0x32D2, 0xC368}, + {0x32D4, 0xC376}, + {0x32D6, 0xC3C2}, + {0x32D8, 0xC3E6}, + {0x32DA, 0x0003}, + {0x32DC, 0x0003}, + {0x32DE, 0x00C7}, + {0x32E0, 0x0031}, + {0x32E2, 0x0031}, + {0x32E4, 0x0031}, + {0x32E6, 0xFC28}, + {0x32E8, 0xC3BC}, + {0x32EA, 0xC384}, + {0x32EC, 0xC392}, + {0x32EE, 0xC3A0}, + {0x32F0, 0xC3AE}, + {0x32F2, 0xC3C4}, + {0x32F4, 0xC3E6}, + {0x32F6, 0x0003}, + {0x32F8, 0x0003}, + {0x32FA, 0x00C7}, + {0x32FC, 0x0031}, + {0x32FE, 0x0031}, + {0x3300, 0x0031}, + {0x3302, 0x82CA}, + {0x3304, 0xC164}, + {0x3306, 0x82E6}, + {0x3308, 0xC19C}, + {0x330A, 0x001F}, + {0x330C, 0x001A}, + {0x330E, 0x0034}, + {0x3310, 0x0000}, + {0x3312, 0x0000}, + {0x3314, 0xFC94}, + {0x3316, 0xC3D8}, + + {0x0A00, 0x0000}, + {0x0E04, 0x0012}, + {0x002E, 0x1111}, + {0x0032, 0x1111}, + {0x0022, 0x0008}, + {0x0026, 0x0040}, + {0x0028, 0x0017}, + {0x002C, 0x09CF}, + {0x005C, 0x2101}, + {0x0006, 0x09DE}, + {0x0008, 0x0ED8}, + {0x000E, 0x0100}, + {0x000C, 0x0022}, + {0x0A22, 0x0000}, + {0x0A24, 0x0000}, + {0x0804, 0x0000}, + {0x0A12, 0x0CC0}, + {0x0A14, 0x0990}, + {0x0074, 0x09D8}, + {0x0076, 0x0000}, + {0x051E, 0x0000}, + {0x0200, 0x0400}, + {0x0A1A, 0x0C00}, + {0x0A0C, 0x0010}, + {0x0A1E, 0x0CCF}, + {0x0402, 0x0110}, + {0x0404, 0x00F4}, + {0x0408, 0x0000}, + {0x0410, 0x008D}, + {0x0412, 0x011A}, + {0x0414, 0x864C}, + /* For OTP */ + {0x021C, 0x0003}, + {0x021E, 0x0235}, + /* For OTP */ + {0x0C00, 0x9950}, + {0x0C06, 0x0021}, + {0x0C10, 0x0040}, + {0x0C12, 0x0040}, + {0x0C14, 0x0040}, + {0x0C16, 0x0040}, + {0x0A02, 0x0100}, + {0x0A04, 0x015A}, + {0x0418, 0x0000}, + {0x0128, 0x0028}, + {0x012A, 0xFFFF}, + {0x0120, 0x0046}, + {0x0122, 0x0376}, + {0x012C, 0x0020}, + {0x012E, 0xFFFF}, + {0x0124, 0x0040}, + {0x0126, 0x0378}, + {0x0746, 0x0050}, + {0x0748, 0x01D5}, + {0x074A, 0x022B}, + {0x074C, 0x03B0}, + {0x0756, 0x043F}, + {0x0758, 0x3F1D}, + {0x0B02, 0xE04D}, + {0x0B10, 0x6821}, + {0x0B12, 0x0120}, + {0x0B14, 0x0001}, + {0x2008, 0x38FD}, + {0x326E, 0x0000}, + {0x0900, 0x0300}, + {0x0902, 0xC319}, + {0x0914, 0xC109}, + {0x0916, 0x061A}, + {0x0918, 0x0407}, + {0x091A, 0x0A0B}, + {0x091C, 0x0E08}, + {0x091E, 0x0A00}, + {0x090C, 0x0427}, + {0x090E, 0x0059}, + {0x0954, 0x0089}, + {0x0956, 0x0000}, + {0x0958, 0xCA80}, + {0x095A, 0x9240}, + {0x0F08, 0x2F04}, + {0x0F30, 0x001F}, + {0x0F36, 0x001F}, + {0x0F04, 0x3A00}, + {0x0F32, 0x025A}, + {0x0F38, 0x025A}, + {0x0F2A, 0x4124}, + {0x006A, 0x0100}, + {0x004C, 0x0100}, + {0x0044, 0x0001}, +}; + +static const struct hi846_reg mode_640x480_config[] = { + {HI846_REG_MODE_SELECT, 0x0000}, + {HI846_REG_Y_ODD_INC_FOBP, 0x7711}, + {HI846_REG_Y_ODD_INC_VACT, 0x7711}, + {HI846_REG_Y_ADDR_START_VACT_H, 0x0148}, + {HI846_REG_Y_ADDR_END_VACT_H, 0x08C7}, + {HI846_REG_UNKNOWN_005C, 0x4404}, + {HI846_REG_FLL, 0x0277}, + {HI846_REG_LLP, 0x0ED8}, + {HI846_REG_BINNING_MODE, 0x0322}, + {HI846_REG_HBIN_MODE, 0x0200}, + {HI846_REG_UNKNOWN_0A24, 0x0000}, + {HI846_REG_X_START_H, 0x0058}, + {HI846_REG_X_OUTPUT_SIZE_H, 0x0280}, + {HI846_REG_Y_OUTPUT_SIZE_H, 0x01E0}, + + /* For OTP */ + {HI846_REG_UNKNOWN_021C, 0x0003}, + {HI846_REG_UNKNOWN_021E, 0x0235}, + + {HI846_REG_ISP_EN_H, 0x017A}, + {HI846_REG_UNKNOWN_0418, 0x0210}, + {HI846_REG_UNKNOWN_0B02, 0xE04D}, + {HI846_REG_UNKNOWN_0B10, 0x7021}, + {HI846_REG_UNKNOWN_0B12, 0x0120}, + {HI846_REG_UNKNOWN_0B14, 0x0001}, + {HI846_REG_UNKNOWN_2008, 0x38FD}, + {HI846_REG_UNKNOWN_326E, 0x0000}, +}; + +static const struct hi846_reg mode_640x480_mipi_2lane[] = { + {HI846_REG_UNKNOWN_0900, 0x0300}, + {HI846_REG_MIPI_TX_OP_MODE, 0x4319}, + {HI846_REG_UNKNOWN_0914, 0xC105}, + {HI846_REG_TCLK_PREPARE, 0x030C}, + {HI846_REG_UNKNOWN_0918, 0x0304}, + {HI846_REG_THS_ZERO, 0x0708}, + {HI846_REG_TCLK_POST, 0x0B04}, + {HI846_REG_UNKNOWN_091E, 0x0500}, + {HI846_REG_UNKNOWN_090C, 0x0208}, + {HI846_REG_UNKNOWN_090E, 0x009A}, + {HI846_REG_UNKNOWN_0954, 0x0089}, + {HI846_REG_UNKNOWN_0956, 0x0000}, + {HI846_REG_UNKNOWN_0958, 0xCA80}, + {HI846_REG_UNKNOWN_095A, 0x9240}, + {HI846_REG_PLL_CFG_MIPI2_H, 0x4924}, + {HI846_REG_TG_ENABLE, 0x0100}, +}; + +static const struct hi846_reg mode_1280x720_config[] = { + {HI846_REG_MODE_SELECT, 0x0000}, + {HI846_REG_Y_ODD_INC_FOBP, 0x3311}, + {HI846_REG_Y_ODD_INC_VACT, 0x3311}, + {HI846_REG_Y_ADDR_START_VACT_H, 0x0238}, + {HI846_REG_Y_ADDR_END_VACT_H, 0x07D7}, + {HI846_REG_UNKNOWN_005C, 0x4202}, + {HI846_REG_FLL, 0x034A}, + {HI846_REG_LLP, 0x0ED8}, + {HI846_REG_BINNING_MODE, 0x0122}, + {HI846_REG_HBIN_MODE, 0x0100}, + {HI846_REG_UNKNOWN_0A24, 0x0000}, + {HI846_REG_X_START_H, 0x00B0}, + {HI846_REG_X_OUTPUT_SIZE_H, 0x0500}, + {HI846_REG_Y_OUTPUT_SIZE_H, 0x02D0}, + {HI846_REG_EXPOSURE, 0x0344}, + + /* For OTP */ + {HI846_REG_UNKNOWN_021C, 0x0003}, + {HI846_REG_UNKNOWN_021E, 0x0235}, + + {HI846_REG_ISP_EN_H, 0x017A}, + {HI846_REG_UNKNOWN_0418, 0x0410}, + {HI846_REG_UNKNOWN_0B02, 0xE04D}, + {HI846_REG_UNKNOWN_0B10, 0x6C21}, + {HI846_REG_UNKNOWN_0B12, 0x0120}, + {HI846_REG_UNKNOWN_0B14, 0x0005}, + {HI846_REG_UNKNOWN_2008, 0x38FD}, + {HI846_REG_UNKNOWN_326E, 0x0000}, +}; + +static const struct hi846_reg mode_1280x720_mipi_2lane[] = { + {HI846_REG_UNKNOWN_0900, 0x0300}, + {HI846_REG_MIPI_TX_OP_MODE, 0x4319}, + {HI846_REG_UNKNOWN_0914, 0xC109}, + {HI846_REG_TCLK_PREPARE, 0x061A}, + {HI846_REG_UNKNOWN_0918, 0x0407}, + {HI846_REG_THS_ZERO, 0x0A0B}, + {HI846_REG_TCLK_POST, 0x0E08}, + {HI846_REG_UNKNOWN_091E, 0x0A00}, + {HI846_REG_UNKNOWN_090C, 0x0427}, + {HI846_REG_UNKNOWN_090E, 0x0145}, + {HI846_REG_UNKNOWN_0954, 0x0089}, + {HI846_REG_UNKNOWN_0956, 0x0000}, + {HI846_REG_UNKNOWN_0958, 0xCA80}, + {HI846_REG_UNKNOWN_095A, 0x9240}, + {HI846_REG_PLL_CFG_MIPI2_H, 0x4124}, + {HI846_REG_TG_ENABLE, 0x0100}, +}; + +static const struct hi846_reg mode_1280x720_mipi_4lane[] = { + /* 360Mbps */ + {HI846_REG_UNKNOWN_0900, 0x0300}, + {HI846_REG_MIPI_TX_OP_MODE, 0xC319}, + {HI846_REG_UNKNOWN_0914, 0xC105}, + {HI846_REG_TCLK_PREPARE, 0x030C}, + {HI846_REG_UNKNOWN_0918, 0x0304}, + {HI846_REG_THS_ZERO, 0x0708}, + {HI846_REG_TCLK_POST, 0x0B04}, + {HI846_REG_UNKNOWN_091E, 0x0500}, + {HI846_REG_UNKNOWN_090C, 0x0208}, + {HI846_REG_UNKNOWN_090E, 0x008A}, + {HI846_REG_UNKNOWN_0954, 0x0089}, + {HI846_REG_UNKNOWN_0956, 0x0000}, + {HI846_REG_UNKNOWN_0958, 0xCA80}, + {HI846_REG_UNKNOWN_095A, 0x9240}, + {HI846_REG_PLL_CFG_MIPI2_H, 0x4924}, + {HI846_REG_TG_ENABLE, 0x0100}, +}; + +static const struct hi846_reg mode_1632x1224_config[] = { + {HI846_REG_MODE_SELECT, 0x0000}, + {HI846_REG_Y_ODD_INC_FOBP, 0x3311}, + {HI846_REG_Y_ODD_INC_VACT, 0x3311}, + {HI846_REG_Y_ADDR_START_VACT_H, 0x0040}, + {HI846_REG_Y_ADDR_END_VACT_H, 0x09CF}, + {HI846_REG_UNKNOWN_005C, 0x4202}, + {HI846_REG_FLL, 0x09DE}, + {HI846_REG_LLP, 0x0ED8}, + {HI846_REG_BINNING_MODE, 0x0122}, + {HI846_REG_HBIN_MODE, 0x0100}, + {HI846_REG_UNKNOWN_0A24, 0x0000}, + {HI846_REG_X_START_H, 0x0000}, + {HI846_REG_X_OUTPUT_SIZE_H, 0x0660}, + {HI846_REG_Y_OUTPUT_SIZE_H, 0x04C8}, + {HI846_REG_EXPOSURE, 0x09D8}, + {HI846_REG_ISP_EN_H, 0x017A}, + + /* For OTP */ + {HI846_REG_UNKNOWN_021C, 0x0003}, + {HI846_REG_UNKNOWN_021E, 0x0235}, + + {HI846_REG_UNKNOWN_0418, 0x0000}, + {HI846_REG_UNKNOWN_0B02, 0xE04D}, + {HI846_REG_UNKNOWN_0B10, 0x6C21}, + {HI846_REG_UNKNOWN_0B12, 0x0120}, + {HI846_REG_UNKNOWN_0B14, 0x0005}, + {HI846_REG_UNKNOWN_2008, 0x38FD}, + {HI846_REG_UNKNOWN_326E, 0x0000}, +}; + +static const struct hi846_reg mode_1632x1224_mipi_2lane[] = { + {HI846_REG_UNKNOWN_0900, 0x0300}, + {HI846_REG_MIPI_TX_OP_MODE, 0x4319}, + {HI846_REG_UNKNOWN_0914, 0xC109}, + {HI846_REG_TCLK_PREPARE, 0x061A}, + {HI846_REG_UNKNOWN_0918, 0x0407}, + {HI846_REG_THS_ZERO, 0x0A0B}, + {HI846_REG_TCLK_POST, 0x0E08}, + {HI846_REG_UNKNOWN_091E, 0x0A00}, + {HI846_REG_UNKNOWN_090C, 0x0427}, + {HI846_REG_UNKNOWN_090E, 0x0069}, + {HI846_REG_UNKNOWN_0954, 0x0089}, + {HI846_REG_UNKNOWN_0956, 0x0000}, + {HI846_REG_UNKNOWN_0958, 0xCA80}, + {HI846_REG_UNKNOWN_095A, 0x9240}, + {HI846_REG_PLL_CFG_MIPI2_H, 0x4124}, + {HI846_REG_TG_ENABLE, 0x0100}, +}; + +static const struct hi846_reg mode_1632x1224_mipi_4lane[] = { + {HI846_REG_UNKNOWN_0900, 0x0300}, + {HI846_REG_MIPI_TX_OP_MODE, 0xC319}, + {HI846_REG_UNKNOWN_0914, 0xC105}, + {HI846_REG_TCLK_PREPARE, 0x030C}, + {HI846_REG_UNKNOWN_0918, 0x0304}, + {HI846_REG_THS_ZERO, 0x0708}, + {HI846_REG_TCLK_POST, 0x0B04}, + {HI846_REG_UNKNOWN_091E, 0x0500}, + {HI846_REG_UNKNOWN_090C, 0x0208}, + {HI846_REG_UNKNOWN_090E, 0x001C}, + {HI846_REG_UNKNOWN_0954, 0x0089}, + {HI846_REG_UNKNOWN_0956, 0x0000}, + {HI846_REG_UNKNOWN_0958, 0xCA80}, + {HI846_REG_UNKNOWN_095A, 0x9240}, + {HI846_REG_PLL_CFG_MIPI2_H, 0x4924}, + {HI846_REG_TG_ENABLE, 0x0100}, +}; + +static const char * const hi846_test_pattern_menu[] = { + "Disabled", + "Solid Colour", + "100% Colour Bars", + "Fade To Grey Colour Bars", + "PN9", + "Gradient Horizontal", + "Gradient Vertical", + "Check Board", + "Slant Pattern", + "Resolution Pattern", +}; + +#define FREQ_INDEX_640 0 +#define FREQ_INDEX_1280 1 +static const s64 hi846_link_freqs[] = { + [FREQ_INDEX_640] = 80000000, + [FREQ_INDEX_1280] = 200000000, +}; + +static const struct hi846_reg_list hi846_init_regs_list_2lane = { + .num_of_regs = ARRAY_SIZE(hi846_init_2lane), + .regs = hi846_init_2lane, +}; + +static const struct hi846_reg_list hi846_init_regs_list_4lane = { + .num_of_regs = ARRAY_SIZE(hi846_init_4lane), + .regs = hi846_init_4lane, +}; + +static const struct hi846_mode supported_modes[] = { + { + .width = 640, + .height = 480, + .link_freq_index = FREQ_INDEX_640, + .fps = 120, + .frame_len = 631, + .llp = HI846_LINE_LENGTH, + .reg_list_config = { + .num_of_regs = ARRAY_SIZE(mode_640x480_config), + .regs = mode_640x480_config, + }, + .reg_list_2lane = { + .num_of_regs = ARRAY_SIZE(mode_640x480_mipi_2lane), + .regs = mode_640x480_mipi_2lane, + }, + }, + { + .width = 1280, + .height = 720, + .link_freq_index = FREQ_INDEX_1280, + .fps = 90, + .frame_len = 842, + .llp = HI846_LINE_LENGTH, + .reg_list_config = { + .num_of_regs = ARRAY_SIZE(mode_1280x720_config), + .regs = mode_1280x720_config, + }, + .reg_list_2lane = { + .num_of_regs = ARRAY_SIZE(mode_1280x720_mipi_2lane), + .regs = mode_1280x720_mipi_2lane, + }, + .reg_list_4lane = { + .num_of_regs = ARRAY_SIZE(mode_1280x720_mipi_4lane), + .regs = mode_1280x720_mipi_4lane, + }, + }, + { + .width = 1632, + .height = 1224, + .link_freq_index = FREQ_INDEX_1280, + .fps = 30, + .frame_len = 2526, + .llp = HI846_LINE_LENGTH, + .reg_list_config = { + .num_of_regs = ARRAY_SIZE(mode_1632x1224_config), + .regs = mode_1632x1224_config, + }, + .reg_list_2lane = { + .num_of_regs = ARRAY_SIZE(mode_1632x1224_mipi_2lane), + .regs = mode_1632x1224_mipi_2lane, + }, + .reg_list_4lane = { + .num_of_regs = ARRAY_SIZE(mode_1632x1224_mipi_4lane), + .regs = mode_1632x1224_mipi_4lane, + }, + } +}; + +struct hi846_gpio { + int gpio; + int level; +}; + +struct hi846_datafmt { + u32 code; + enum v4l2_colorspace colorspace; +}; + +struct hi846 { + struct hi846_gpio rst_gpio; + struct regulator *vdd1_regulator; + struct regulator *vdd_regulator; + struct clk *clock; + struct hi846_datafmt *fmt; + struct v4l2_subdev sd; + struct media_pad pad; + struct v4l2_ctrl_handler ctrl_handler; + u8 nr_lanes; + + struct v4l2_ctrl *link_freq; + struct v4l2_ctrl *pixel_rate; + struct v4l2_ctrl *vblank; + struct v4l2_ctrl *hblank; + struct v4l2_ctrl *exposure; + + const struct hi846_mode *cur_mode; + struct mutex mutex; + bool streaming; +}; + +static struct hi846_datafmt hi846_colour_fmts[] = { + {HI846_MEDIA_BUS_FORMAT, V4L2_COLORSPACE_RAW}, +}; + +static struct hi846_datafmt *hi846_find_datafmt(u32 code) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(hi846_colour_fmts); i++) + if (hi846_colour_fmts[i].code == code) + return hi846_colour_fmts + i; + + return NULL; +} + +static inline u8 hi846_get_link_freq_index(struct hi846 *hi846) +{ + return hi846->cur_mode->link_freq_index; +} + +static s64 hi846_get_link_freq(struct hi846 *hi846) +{ + u8 index = hi846_get_link_freq_index(hi846); + + return *(hi846_link_freqs + index); +} + +static u64 hi846_calc_pixel_rate(struct hi846 *hi846) +{ + s64 link_freq = hi846_get_link_freq(hi846); + u64 pixel_rate = link_freq * 2 * hi846->nr_lanes; + + do_div(pixel_rate, HI846_RGB_DEPTH); + + return pixel_rate; +} + +static int hi846_read_reg(struct hi846 *hi846, u16 reg, u8 *val) +{ + struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd); + struct i2c_msg msgs[2]; + u8 addr_buf[2]; + u8 data_buf[1] = {0}; + int ret; + + put_unaligned_be16(reg, addr_buf); + msgs[0].addr = client->addr; + msgs[0].flags = 0; + msgs[0].len = sizeof(addr_buf); + msgs[0].buf = addr_buf; + msgs[1].addr = client->addr; + msgs[1].flags = I2C_M_RD; + msgs[1].len = 1; + msgs[1].buf = &data_buf[0]; + + ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs)); + if (ret != ARRAY_SIZE(msgs)) { + dev_err(&client->dev, "i2c read error: %d\n", ret); + return -EIO; + } + + *val = data_buf[0]; + + return 0; +} + +static int hi846_write_reg_16(struct hi846 *hi846, u16 reg, u16 val) +{ + struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd); + u8 buf[6]; + + put_unaligned_be16(reg, buf); + put_unaligned_be32(val << 8 * 2, buf + 2); + if (i2c_master_send(client, buf, 4) != 4) + return -EIO; + + return 0; +} + +static int hi846_write_reg_list(struct hi846 *hi846, + const struct hi846_reg_list *r_list) +{ + struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd); + unsigned int i; + int ret; + + for (i = 0; i < r_list->num_of_regs; i++) { + ret = hi846_write_reg_16(hi846, r_list->regs[i].address, + r_list->regs[i].val); + if (ret) { + dev_err_ratelimited(&client->dev, + "failed to write reg 0x%4.4x. error = %d", + r_list->regs[i].address, ret); + return ret; + } + } + + return 0; +} + +static int hi846_write_reg(struct hi846 *hi846, u16 reg, u8 val) +{ + struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd); + u8 buf[3] = { reg >> 8, reg & 0xff, val }; + int ret; + + struct i2c_msg msg[] = { + { .addr = client->addr, .flags = 0, + .len = ARRAY_SIZE(buf), .buf = buf }, + }; + + ret = i2c_transfer(client->adapter, msg, ARRAY_SIZE(msg)); + if (ret != ARRAY_SIZE(msg)) { + dev_err(&client->dev, "i2c write error\n"); + return -EIO; + } + + return 0; +} + +static int hi846_update_digital_gain(struct hi846 *hi846, u16 d_gain) +{ + int ret; + + ret = hi846_write_reg_16(hi846, HI846_REG_MWB_GR_GAIN_H, d_gain); + if (ret) + return ret; + + ret = hi846_write_reg_16(hi846, HI846_REG_MWB_GB_GAIN_H, d_gain); + if (ret) + return ret; + + ret = hi846_write_reg_16(hi846, HI846_REG_MWB_R_GAIN_H, d_gain); + if (ret) + return ret; + + return hi846_write_reg_16(hi846, HI846_REG_MWB_B_GAIN_H, d_gain); +} + +static int hi846_test_pattern(struct hi846 *hi846, u32 pattern) +{ + int ret; + u8 val; + + if (pattern) { + ret = hi846_read_reg(hi846, HI846_REG_ISP, &val); + if (ret) + return ret; + + ret = hi846_write_reg(hi846, HI846_REG_ISP, + val | HI846_REG_ISP_TPG_EN); + if (ret) + return ret; + } + + return hi846_write_reg(hi846, HI846_REG_TEST_PATTERN, pattern); +} + +static int hi846_set_ctrl(struct v4l2_ctrl *ctrl) +{ + struct hi846 *hi846 = container_of(ctrl->handler, + struct hi846, ctrl_handler); + struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd); + s64 exposure_max; + int ret = 0; + u32 shutter, frame_len; + + if (!pm_runtime_get_if_in_use(&client->dev)) + goto out; + + /* Propagate change of current control to all related controls */ + if (ctrl->id == V4L2_CID_VBLANK) { + /* Update max exposure while meeting expected vblanking */ + exposure_max = hi846->cur_mode->height + ctrl->val - + HI846_EXPOSURE_MAX_MARGIN; + __v4l2_ctrl_modify_range(hi846->exposure, + hi846->exposure->minimum, + exposure_max, hi846->exposure->step, + exposure_max); + } + + switch (ctrl->id) { + case V4L2_CID_ANALOGUE_GAIN: + ret = hi846_write_reg(hi846, HI846_REG_ANALOG_GAIN, ctrl->val); + break; + + case V4L2_CID_DIGITAL_GAIN: + ret = hi846_update_digital_gain(hi846, ctrl->val); + break; + + case V4L2_CID_EXPOSURE: + shutter = ctrl->val; + frame_len = hi846->cur_mode->frame_len; + + if (shutter > frame_len - 6) { /* margin */ + frame_len = shutter + 6; + if (frame_len > 0xffff) { /* max frame len */ + frame_len = 0xffff; + } + } + + if (shutter < 6) + shutter = 6; + if (shutter > (0xffff - 6)) + shutter = 0xffff - 6; + + ret = hi846_write_reg_16(hi846, HI846_REG_FLL, + frame_len); + ret = hi846_write_reg_16(hi846, HI846_REG_EXPOSURE, + shutter); + break; + + case V4L2_CID_VBLANK: + /* Update FLL that meets expected vertical blanking */ + ret = hi846_write_reg_16(hi846, HI846_REG_FLL, + hi846->cur_mode->height + ctrl->val); + break; + case V4L2_CID_TEST_PATTERN: + ret = hi846_test_pattern(hi846, ctrl->val); + break; + + default: + ret = -EINVAL; + break; + } + + pm_runtime_put(&client->dev); +out: + return ret; +} + +static const struct v4l2_ctrl_ops hi846_ctrl_ops = { + .s_ctrl = hi846_set_ctrl, +}; + +static int hi846_init_controls(struct hi846 *hi846) +{ + struct v4l2_ctrl_handler *ctrl_hdlr; + s64 exposure_max, h_blank; + int ret; + struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd); + + ctrl_hdlr = &hi846->ctrl_handler; + ret = v4l2_ctrl_handler_init(ctrl_hdlr, 8); + if (ret) + return ret; + + ctrl_hdlr->lock = &hi846->mutex; + + hi846->link_freq = v4l2_ctrl_new_int_menu(ctrl_hdlr, &hi846_ctrl_ops, + V4L2_CID_LINK_FREQ, + ARRAY_SIZE(hi846_link_freqs) - 1, + 0, hi846_link_freqs); + if (hi846->link_freq) + hi846->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY; + + hi846->pixel_rate = v4l2_ctrl_new_std + (ctrl_hdlr, &hi846_ctrl_ops, + V4L2_CID_PIXEL_RATE, 0, + hi846_calc_pixel_rate(hi846), + 1, + hi846_calc_pixel_rate(hi846)); + hi846->vblank = v4l2_ctrl_new_std(ctrl_hdlr, &hi846_ctrl_ops, + V4L2_CID_VBLANK, + hi846->cur_mode->frame_len - + hi846->cur_mode->height, + HI846_FLL_MAX - + hi846->cur_mode->height, 1, + hi846->cur_mode->frame_len - + hi846->cur_mode->height); + + h_blank = hi846->cur_mode->llp - hi846->cur_mode->width; + + hi846->hblank = v4l2_ctrl_new_std(ctrl_hdlr, &hi846_ctrl_ops, + V4L2_CID_HBLANK, h_blank, h_blank, 1, + h_blank); + if (hi846->hblank) + hi846->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY; + + v4l2_ctrl_new_std(ctrl_hdlr, &hi846_ctrl_ops, V4L2_CID_ANALOGUE_GAIN, + HI846_ANAL_GAIN_MIN, HI846_ANAL_GAIN_MAX, + HI846_ANAL_GAIN_STEP, HI846_ANAL_GAIN_MIN); + v4l2_ctrl_new_std(ctrl_hdlr, &hi846_ctrl_ops, V4L2_CID_DIGITAL_GAIN, + HI846_DGTL_GAIN_MIN, HI846_DGTL_GAIN_MAX, + HI846_DGTL_GAIN_STEP, HI846_DGTL_GAIN_DEFAULT); + exposure_max = hi846->cur_mode->frame_len - HI846_EXPOSURE_MAX_MARGIN; + hi846->exposure = v4l2_ctrl_new_std(ctrl_hdlr, &hi846_ctrl_ops, + V4L2_CID_EXPOSURE, + HI846_EXPOSURE_MIN, exposure_max, + HI846_EXPOSURE_STEP, + exposure_max); + v4l2_ctrl_new_std_menu_items(ctrl_hdlr, &hi846_ctrl_ops, + V4L2_CID_TEST_PATTERN, + ARRAY_SIZE(hi846_test_pattern_menu) - 1, + 0, 0, hi846_test_pattern_menu); + if (ctrl_hdlr->error) { + dev_err(&client->dev, "v4l ctrl handler error: %d\n", + ctrl_hdlr->error); + return ctrl_hdlr->error; + } + + hi846->sd.ctrl_handler = ctrl_hdlr; + + return 0; +} + +static int hi846_set_video_mode(struct hi846 *hi846, int fps) +{ + struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd); + int frame_length; + int ret; + int dummy_lines; + + dev_dbg(&client->dev, "%s: link freq: %lld\n", __func__, + hi846_get_link_freq(hi846)); + + frame_length = hi846_get_link_freq(hi846) / fps / HI846_LINE_LENGTH; + dummy_lines = (frame_length > hi846->cur_mode->frame_len) ? + (frame_length - hi846->cur_mode->frame_len) : 0; + + frame_length = hi846->cur_mode->frame_len + dummy_lines; + + dev_dbg(&client->dev, "%s: frame length calculated: %d\n", __func__, + frame_length); + + ret = hi846_write_reg_16(hi846, HI846_REG_FLL, frame_length & 0xFFFF); + ret = hi846_write_reg_16(hi846, HI846_REG_LLP, HI846_LINE_LENGTH & 0xFFFF); + + return ret; +} + +static int hi846_start_streaming(struct hi846 *hi846) +{ + struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd); + int ret = 0; + u8 val; + + if (hi846->nr_lanes == 2) + ret = hi846_write_reg_list(hi846, &hi846_init_regs_list_2lane); + else + ret = hi846_write_reg_list(hi846, &hi846_init_regs_list_4lane); + if (ret) { + dev_err(&client->dev, "failed to set plls: %d\n", ret); + return ret; + } + + ret = hi846_write_reg_list(hi846, &hi846->cur_mode->reg_list_config); + if (ret) { + dev_err(&client->dev, "failed to set mode: %d\n", ret); + return ret; + } + + if (hi846->nr_lanes == 2) { + if (!&hi846->cur_mode->reg_list_2lane) { + dev_err(&client->dev, "2 lanes unsupported for this mode\n"); + return -EINVAL; + } + ret = hi846_write_reg_list(hi846, &hi846->cur_mode->reg_list_2lane); + } else { + if (!&hi846->cur_mode->reg_list_4lane) { + dev_err(&client->dev, "4 lanes unsupported for this mode\n"); + return -EINVAL; + } + ret = hi846_write_reg_list(hi846, &hi846->cur_mode->reg_list_4lane); + } + if (ret) { + dev_err(&client->dev, "failed to set mipi mode: %d\n", ret); + return ret; + } + + hi846_set_video_mode(hi846, hi846->cur_mode->fps); + + ret = __v4l2_ctrl_handler_setup(hi846->sd.ctrl_handler); + if (ret) + return ret; + + /* + * Reading 0x0034 is purely done for debugging reasons: It is not + * documented in the DS but only mentioned once: + * "If 0x0034[2] bit is disabled , Visible pixel width and height is 0." + * So even though that sounds like we won't see anything, we don't + * know more about this, so in that case only inform the user but do + * nothing more. + */ + ret = hi846_read_reg(hi846, 0x0034, &val); + if (ret) + return ret; + if (!(val & BIT(2))) + dev_info(&client->dev, "visible pixel width and height is 0\n"); + + ret = hi846_write_reg(hi846, HI846_REG_MODE_SELECT, + HI846_MODE_STREAMING); + if (ret) { + dev_err(&client->dev, "failed to start stream"); + return ret; + } + + hi846->streaming = 1; + + dev_dbg(&client->dev, "%s: started streaming successfully\n", __func__); + + return ret; +} + +static void hi846_stop_streaming(struct hi846 *hi846) +{ + struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd); + + if (hi846_write_reg(hi846, HI846_REG_MODE_SELECT, HI846_MODE_STANDBY)) + dev_err(&client->dev, "failed to stop stream"); + + hi846->streaming = 0; +} + +static int hi846_set_stream(struct v4l2_subdev *sd, int enable) +{ + struct hi846 *hi846 = to_hi846(sd); + struct i2c_client *client = v4l2_get_subdevdata(sd); + int ret = 0; + + if (hi846->streaming == enable) + return 0; + + mutex_lock(&hi846->mutex); + + if (enable) { + ret = pm_runtime_get_sync(&client->dev); + if (ret < 0) { + pm_runtime_put_noidle(&client->dev); + goto out; + } + + ret = hi846_start_streaming(hi846); + if (ret) { + enable = 0; + hi846_stop_streaming(hi846); + pm_runtime_put(&client->dev); + } + } else { + hi846_stop_streaming(hi846); + pm_runtime_put(&client->dev); + } + +out: + mutex_unlock(&hi846->mutex); + + return ret; +} + +static int hi846_regulator_enable(struct hi846 *hi846) +{ + int ret = 0; + + ret = regulator_enable(hi846->vdd_regulator); + if (ret) + return ret; + + return regulator_enable(hi846->vdd1_regulator); +} + +static void hi846_regulator_disable(struct hi846 *hi846) +{ + if (regulator_is_enabled(hi846->vdd1_regulator)) + regulator_disable(hi846->vdd1_regulator); + + if (regulator_is_enabled(hi846->vdd_regulator)) + regulator_disable(hi846->vdd_regulator); +} + +static int __maybe_unused hi846_suspend(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct v4l2_subdev *sd = i2c_get_clientdata(client); + struct hi846 *hi846 = to_hi846(sd); + + if (hi846->streaming) + hi846_stop_streaming(hi846); + + if (!IS_ERR(hi846->clock)) + clk_disable_unprepare(hi846->clock); + + hi846_regulator_disable(hi846); + + return 0; +} + +static int __maybe_unused hi846_resume(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct v4l2_subdev *sd = i2c_get_clientdata(client); + struct hi846 *hi846 = to_hi846(sd); + int ret; + + ret = hi846_regulator_enable(hi846); + if (ret) { + dev_err(dev, "enable regulator failed: %d\n", ret); + return ret; + } + + ret = clk_prepare_enable(hi846->clock); + if (ret < 0) { + dev_err(dev, "enable clk failed: %d\n", ret); + goto error_regulator; + } + + msleep(100); + + if (hi846->streaming) { + ret = hi846_start_streaming(hi846); + if (ret) { + dev_err(dev, "%s: start streaming failed: %d\n", + __func__, ret); + goto error; + } + } + + return 0; + +error: + clk_disable_unprepare(hi846->clock); + +error_regulator: + hi846_regulator_disable(hi846); + + return ret; +} + +static int hi846_set_format(struct v4l2_subdev *sd, + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_format *format) +{ + struct hi846 *hi846 = to_hi846(sd); + struct v4l2_mbus_framefmt *mf = &format->format; + struct i2c_client *client = v4l2_get_subdevdata(sd); + struct hi846_datafmt *fmt = hi846_find_datafmt(mf->code); + u32 tgt_fps; + s32 vblank_def, h_blank; + + if (!fmt) { + mf->code = hi846_colour_fmts[0].code; + mf->colorspace = hi846_colour_fmts[0].colorspace; + fmt = &hi846_colour_fmts[0]; + } + + if (format->which == V4L2_SUBDEV_FORMAT_TRY) { + *v4l2_subdev_get_try_format(sd, cfg, format->pad) = *mf; + return 0; + } + + mutex_lock(&hi846->mutex); + + if (hi846->streaming) { + mutex_unlock(&hi846->mutex); + return -EBUSY; + } + + hi846->fmt = fmt; + + hi846->cur_mode = v4l2_find_nearest_size(supported_modes, + ARRAY_SIZE(supported_modes), width, + height, mf->width, + mf->height); + dev_dbg(&client->dev, "%s: found mode: %dx%d\n", __func__, + hi846->cur_mode->width, hi846->cur_mode->height); + + tgt_fps = hi846->cur_mode->fps; + dev_dbg(&client->dev, "%s: target fps: %d\n", __func__, tgt_fps); + + mf->width = hi846->cur_mode->width; + mf->height = hi846->cur_mode->height; + mf->code = HI846_MEDIA_BUS_FORMAT; + mf->field = V4L2_FIELD_NONE; + + __v4l2_ctrl_s_ctrl(hi846->link_freq, hi846_get_link_freq_index(hi846)); + __v4l2_ctrl_s_ctrl_int64(hi846->pixel_rate, + hi846_calc_pixel_rate(hi846)); + + /* Update limits and set FPS to default */ + vblank_def = hi846->cur_mode->frame_len - hi846->cur_mode->height; + __v4l2_ctrl_modify_range(hi846->vblank, + hi846->cur_mode->frame_len - hi846->cur_mode->height, + HI846_FLL_MAX - hi846->cur_mode->height, 1, + vblank_def); + __v4l2_ctrl_s_ctrl(hi846->vblank, vblank_def); + + h_blank = hi846->cur_mode->llp - hi846->cur_mode->width; + + __v4l2_ctrl_modify_range(hi846->hblank, h_blank, h_blank, 1, + h_blank); + + dev_dbg(&client->dev, "Set fmt w=%d h=%d code=0x%x colorspace=0x%x\n", + mf->width, mf->height, + fmt->code, fmt->colorspace); + + mutex_unlock(&hi846->mutex); + + return 0; +} + +static int hi846_get_format(struct v4l2_subdev *sd, + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_format *format) +{ + struct hi846 *hi846 = to_hi846(sd); + struct v4l2_mbus_framefmt *mf = &format->format; + struct i2c_client *client = v4l2_get_subdevdata(sd); + + if (format->pad) + return -EINVAL; + + if (format->which == V4L2_SUBDEV_FORMAT_TRY) { + format->format = *v4l2_subdev_get_try_format(&hi846->sd, + cfg, + format->pad); + return 0; + } + + mutex_lock(&hi846->mutex); + mf->code = HI846_MEDIA_BUS_FORMAT; + mf->colorspace = V4L2_COLORSPACE_RAW; + mf->field = V4L2_FIELD_NONE; + mf->width = hi846->cur_mode->width; + mf->height = hi846->cur_mode->height; + mutex_unlock(&hi846->mutex); + dev_dbg(&client->dev, + "Get format w=%d h=%d code=0x%x colorspace=0x%x\n", + mf->width, mf->height, mf->code, mf->colorspace); + + return 0; +} + +static int hi846_enum_mbus_code(struct v4l2_subdev *sd, + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_mbus_code_enum *code) +{ + if (code->pad || code->index > 0) + return -EINVAL; + + code->code = HI846_MEDIA_BUS_FORMAT; + + return 0; +} + +static int hi846_enum_frame_size(struct v4l2_subdev *sd, + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_frame_size_enum *fse) +{ + struct i2c_client *client = v4l2_get_subdevdata(sd); + + if (fse->pad || fse->index >= ARRAY_SIZE(supported_modes)) + return -EINVAL; + + if (fse->code != HI846_MEDIA_BUS_FORMAT) { + dev_err(&client->dev, "frame size enum not matching\n"); + return -EINVAL; + } + + fse->min_width = supported_modes[fse->index].width; + fse->max_width = supported_modes[fse->index].width; + fse->min_height = supported_modes[fse->index].height; + fse->max_height = supported_modes[fse->index].height; + + dev_dbg(&client->dev, "%s: max width: %d max height: %d\n", __func__, + fse->max_width, fse->max_height); + + return 0; +} + +static int hi846_s_power(struct v4l2_subdev *sd, int on) +{ + struct hi846 *hi846 = to_hi846(sd); + struct i2c_client *client = v4l2_get_subdevdata(sd); + struct device *dev = &client->dev; + int ret = 0; + + mutex_lock(&hi846->mutex); + if (on) { + ret = hi846_resume(dev); + if (ret) + goto out; + } else { + ret = hi846_suspend(dev); + if (ret) + goto out; + } +out: + mutex_unlock(&hi846->mutex); + return ret; +} + +static int hi846_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh) +{ + struct hi846 *hi846 = to_hi846(sd); + struct v4l2_mbus_framefmt *mf; + + mf = v4l2_subdev_get_try_format(sd, fh->pad, 0); + + mutex_lock(&hi846->mutex); + mf->code = HI846_MEDIA_BUS_FORMAT; + mf->colorspace = V4L2_COLORSPACE_RAW; + mf->field = V4L2_FIELD_NONE; + mf->width = hi846->cur_mode->width; + mf->height = hi846->cur_mode->height; + mutex_unlock(&hi846->mutex); + + return 0; +} + +static const struct v4l2_subdev_video_ops hi846_video_ops = { + .s_stream = hi846_set_stream, +}; + +static const struct v4l2_subdev_pad_ops hi846_pad_ops = { + .enum_frame_size = hi846_enum_frame_size, + .enum_mbus_code = hi846_enum_mbus_code, + .set_fmt = hi846_set_format, + .get_fmt = hi846_get_format, +}; + +static struct v4l2_subdev_core_ops hi846_core_ops = { + .s_power = hi846_s_power, + .log_status = v4l2_ctrl_subdev_log_status, +}; + +static const struct v4l2_subdev_ops hi846_subdev_ops = { + .core = &hi846_core_ops, + .video = &hi846_video_ops, + .pad = &hi846_pad_ops, +}; + +static const struct media_entity_operations hi846_subdev_entity_ops = { + .link_validate = v4l2_subdev_link_validate, +}; + +static const struct v4l2_subdev_internal_ops hi846_internal_ops = { + .open = hi846_open, +}; + +static void hi846_rst_gpio_assert(struct hi846 *hi846, bool on) +{ + struct hi846_gpio *gpio = &hi846->rst_gpio; + + if (gpio == NULL) + return; + + if (on) + gpio_set_value(gpio->gpio, gpio->level); + else + gpio_set_value(gpio->gpio, !gpio->level); +} + +static int hi846_parse_gpio(struct hi846_gpio *gpio, struct device *dev) +{ + struct device_node *node = dev->of_node; + enum of_gpio_flags flags; + int ret; + + ret = of_get_named_gpio_flags(node, "rst-gpios", 0, &flags); + if (ret < 0) { + dev_err(dev, "no rst-gpios provided: %d\n", ret); + return ret; + } + gpio->gpio = ret; + gpio->level = !(flags & OF_GPIO_ACTIVE_LOW); + + return 0; +} + +static int hi846_identify_module(struct hi846 *hi846) +{ + struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd); + int ret; + u8 hi, lo; + + ret = hi846_read_reg(hi846, HI846_REG_CHIP_ID_L, &lo); + if (ret) + return ret; + + if (lo != HI846_CHIP_ID_L) { + dev_err(&client->dev, "wrong chip id low byte: %x", lo); + return -ENXIO; + } + + ret = hi846_read_reg(hi846, HI846_REG_CHIP_ID_H, &hi); + if (ret) + return ret; + + if (hi != HI846_CHIP_ID_H) { + dev_err(&client->dev, "wrong chip id high byte: %x", hi); + return -ENXIO; + } + + dev_info(&client->dev, "chip id %02X %02X / %d mipi lanes\n", hi, lo, + hi846->nr_lanes); + + return 0; +} + +static int hi846_check_hwcfg(struct device *dev, u8 *lanes) +{ + struct fwnode_handle *ep; + struct fwnode_handle *fwnode = dev_fwnode(dev); + struct v4l2_fwnode_endpoint bus_cfg = { + .bus_type = V4L2_MBUS_CSI2_DPHY + }; + int ret = 0; + + if (!fwnode) + return -ENXIO; + + ep = fwnode_graph_get_next_endpoint(fwnode, NULL); + if (!ep) + return -ENXIO; + + ret = v4l2_fwnode_endpoint_alloc_parse(ep, &bus_cfg); + fwnode_handle_put(ep); + if (ret) + return ret; + + if (bus_cfg.bus.mipi_csi2.num_data_lanes != 2 && + bus_cfg.bus.mipi_csi2.num_data_lanes != 4) { + dev_err(dev, "number of CSI2 data lanes %d is not supported", + bus_cfg.bus.mipi_csi2.num_data_lanes); + ret = -EINVAL; + goto check_hwcfg_error; + } + + *lanes = bus_cfg.bus.mipi_csi2.num_data_lanes; + +check_hwcfg_error: + v4l2_fwnode_endpoint_free(&bus_cfg); + + return ret; +} + +static int hi846_remove(struct i2c_client *client) +{ + struct v4l2_subdev *sd = i2c_get_clientdata(client); + struct hi846 *hi846 = to_hi846(sd); + + v4l2_async_unregister_subdev(sd); + media_entity_cleanup(&sd->entity); + v4l2_ctrl_handler_free(sd->ctrl_handler); + + pm_runtime_disable(&client->dev); + if (!pm_runtime_status_suspended(&client->dev)) + hi846_suspend(&client->dev); + pm_runtime_set_suspended(&client->dev); + + mutex_destroy(&hi846->mutex); + + return 0; +} + +static int hi846_probe(struct i2c_client *client) +{ + struct hi846 *hi846; + int ret; + u8 lanes; + + ret = hi846_check_hwcfg(&client->dev, &lanes); + if (ret) { + dev_err(&client->dev, "failed to check HW configuration: %d", + ret); + return ret; + } + + hi846 = devm_kzalloc(&client->dev, sizeof(*hi846), GFP_KERNEL); + if (!hi846) + return -ENOMEM; + + hi846->nr_lanes = lanes; + + v4l2_i2c_subdev_init(&hi846->sd, client, &hi846_subdev_ops); + + ret = hi846_parse_gpio(&hi846->rst_gpio, &client->dev); + if (ret < 0) { + dev_err(&client->dev, "parse gpio failed: %d\n", ret); + return ret; + } + + hi846->vdd_regulator = devm_regulator_get(&client->dev, "vdd"); + if (IS_ERR(hi846->vdd_regulator)) + dev_warn(&client->dev, "cannot get voltage regulator\n"); + + hi846->vdd1_regulator = devm_regulator_get(&client->dev, "vdd1"); + if (IS_ERR(hi846->vdd1_regulator)) + dev_warn(&client->dev, "cannot get voltage regulator\n"); + + ret = hi846_regulator_enable(hi846); + if (ret) { + dev_err(&client->dev, "regulator enable failed: %d\n", ret); + return ret; + } + + hi846->clock = devm_clk_get(hi846->sd.dev, "mclk"); + if (IS_ERR(hi846->clock)) { + dev_err(&client->dev, "get clk failed\n"); + ret = -EPROBE_DEFER; + goto probe_error_regulator; + } + + ret = clk_prepare_enable(hi846->clock); + if (ret < 0) + goto probe_error_regulator; + + msleep(100); + + hi846_rst_gpio_assert(hi846, true); + + ret = hi846_identify_module(hi846); + if (ret) { + dev_err(&client->dev, "failed to find sensor: %d", ret); + goto probe_error_regulator; + } + + mutex_init(&hi846->mutex); + + hi846->cur_mode = &supported_modes[0]; + ret = hi846_init_controls(hi846); + if (ret) { + dev_err(&client->dev, "failed to init controls: %d", ret); + goto probe_error_v4l2_ctrl_handler_free; + } + + hi846->sd.internal_ops = &hi846_internal_ops; + hi846->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; + hi846->sd.entity.ops = &hi846_subdev_entity_ops; + hi846->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR; + hi846->pad.flags = MEDIA_PAD_FL_SOURCE; + ret = media_entity_pads_init(&hi846->sd.entity, 1, &hi846->pad); + if (ret) { + dev_err(&client->dev, "failed to init entity pads: %d", ret); + goto probe_error_v4l2_ctrl_handler_free; + } + + ret = v4l2_async_register_subdev_sensor(&hi846->sd); + if (ret < 0) { + dev_err(&client->dev, "failed to register V4L2 subdev: %d", + ret); + goto probe_error_media_entity_cleanup; + } + + pm_runtime_set_active(&client->dev); + pm_runtime_enable(&client->dev); + pm_runtime_idle(&client->dev); + + return 0; + +probe_error_media_entity_cleanup: + media_entity_cleanup(&hi846->sd.entity); + +probe_error_v4l2_ctrl_handler_free: + v4l2_ctrl_handler_free(hi846->sd.ctrl_handler); + mutex_destroy(&hi846->mutex); + +probe_error_regulator: + hi846_regulator_disable(hi846); + + return ret; +} + +static UNIVERSAL_DEV_PM_OPS(hi846_pm_ops, hi846_suspend, hi846_resume, NULL); + +static const struct of_device_id hi846_of_match[] = { + { .compatible = "hynix,hi846", }, + {}, +}; +MODULE_DEVICE_TABLE(of, hi846_of_match); + +static struct i2c_driver hi846_i2c_driver = { + .driver = { + .name = "hi846", + .pm = &hi846_pm_ops, + .of_match_table = of_match_ptr(hi846_of_match), + }, + .probe_new = hi846_probe, + .remove = hi846_remove, +}; + +module_i2c_driver(hi846_i2c_driver); + +MODULE_AUTHOR("Angus Ainslie <angus@akkea.ca>"); +MODULE_AUTHOR("Martin Kepplinger <martin.kepplinger@puri.sm>"); +MODULE_DESCRIPTION("Hynix HI846 sensor driver"); +MODULE_LICENSE("GPL v2"); -- 2.30.2 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* Re: [PATCH v2 3/5] media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera 2021-05-28 8:13 ` [PATCH v2 3/5] media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera Martin Kepplinger @ 2021-05-28 18:20 ` kernel test robot 2021-05-28 19:08 ` kernel test robot 2021-06-02 14:36 ` Sakari Ailus 2 siblings, 0 replies; 18+ messages in thread From: kernel test robot @ 2021-05-28 18:20 UTC (permalink / raw) To: Martin Kepplinger, laurent.pinchart, mchehab Cc: kbuild-all, devicetree, kernel, krzysztof.kozlowski, linux-kernel, linux-media, paul.kocialkowski, robh, shawnx.tu [-- Attachment #1: Type: text/plain, Size: 1765 bytes --] Hi Martin, I love your patch! Yet something to improve: [auto build test ERROR on linuxtv-media/master] [also build test ERROR on robh/for-next arm64/for-next/core linus/master v5.13-rc3 next-20210528] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in https://git-scm.com/docs/git-format-patch] url: https://github.com/0day-ci/linux/commits/Martin-Kepplinger/Add-support-for-the-Hynix-Hi-846-camera/20210528-161549 base: git://linuxtv.org/media_tree.git master config: h8300-allyesconfig (attached as .config) compiler: h8300-linux-gcc (GCC) 9.3.0 reproduce (this is a W=1 build): wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross # https://github.com/0day-ci/linux/commit/32f267bbcb6cfa4c157f7e105095d16244c01cb2 git remote add linux-review https://github.com/0day-ci/linux git fetch --no-tags linux-review Martin-Kepplinger/Add-support-for-the-Hynix-Hi-846-camera/20210528-161549 git checkout 32f267bbcb6cfa4c157f7e105095d16244c01cb2 # save the attached .config to linux build tree COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-9.3.0 make.cross ARCH=h8300 If you fix the issue, kindly add following tag as appropriate Reported-by: kernel test robot <lkp@intel.com> All errors (new ones prefixed by >>): h8300-linux-ld: drivers/media/i2c/hi846.o: in function `.L104': >> hi846.c:(.text+0xd51): undefined reference to `__divdi3' >> h8300-linux-ld: hi846.c:(.text+0xd6b): undefined reference to `__divdi3' --- 0-DAY CI Kernel Test Service, Intel Corporation https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org [-- Attachment #2: .config.gz --] [-- Type: application/gzip, Size: 58716 bytes --] ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v2 3/5] media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera @ 2021-05-28 18:20 ` kernel test robot 0 siblings, 0 replies; 18+ messages in thread From: kernel test robot @ 2021-05-28 18:20 UTC (permalink / raw) To: kbuild-all [-- Attachment #1: Type: text/plain, Size: 1803 bytes --] Hi Martin, I love your patch! Yet something to improve: [auto build test ERROR on linuxtv-media/master] [also build test ERROR on robh/for-next arm64/for-next/core linus/master v5.13-rc3 next-20210528] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in https://git-scm.com/docs/git-format-patch] url: https://github.com/0day-ci/linux/commits/Martin-Kepplinger/Add-support-for-the-Hynix-Hi-846-camera/20210528-161549 base: git://linuxtv.org/media_tree.git master config: h8300-allyesconfig (attached as .config) compiler: h8300-linux-gcc (GCC) 9.3.0 reproduce (this is a W=1 build): wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross # https://github.com/0day-ci/linux/commit/32f267bbcb6cfa4c157f7e105095d16244c01cb2 git remote add linux-review https://github.com/0day-ci/linux git fetch --no-tags linux-review Martin-Kepplinger/Add-support-for-the-Hynix-Hi-846-camera/20210528-161549 git checkout 32f267bbcb6cfa4c157f7e105095d16244c01cb2 # save the attached .config to linux build tree COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-9.3.0 make.cross ARCH=h8300 If you fix the issue, kindly add following tag as appropriate Reported-by: kernel test robot <lkp@intel.com> All errors (new ones prefixed by >>): h8300-linux-ld: drivers/media/i2c/hi846.o: in function `.L104': >> hi846.c:(.text+0xd51): undefined reference to `__divdi3' >> h8300-linux-ld: hi846.c:(.text+0xd6b): undefined reference to `__divdi3' --- 0-DAY CI Kernel Test Service, Intel Corporation https://lists.01.org/hyperkitty/list/kbuild-all(a)lists.01.org [-- Attachment #2: config.gz --] [-- Type: application/gzip, Size: 58716 bytes --] ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v2 3/5] media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera 2021-05-28 8:13 ` [PATCH v2 3/5] media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera Martin Kepplinger @ 2021-05-28 19:08 ` kernel test robot 2021-05-28 19:08 ` kernel test robot 2021-06-02 14:36 ` Sakari Ailus 2 siblings, 0 replies; 18+ messages in thread From: kernel test robot @ 2021-05-28 19:08 UTC (permalink / raw) To: Martin Kepplinger, laurent.pinchart, mchehab Cc: kbuild-all, devicetree, kernel, krzysztof.kozlowski, linux-kernel, linux-media, paul.kocialkowski, robh, shawnx.tu [-- Attachment #1: Type: text/plain, Size: 2203 bytes --] Hi Martin, I love your patch! Yet something to improve: [auto build test ERROR on linuxtv-media/master] [also build test ERROR on robh/for-next arm64/for-next/core linus/master v5.13-rc3 next-20210528] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in https://git-scm.com/docs/git-format-patch] url: https://github.com/0day-ci/linux/commits/Martin-Kepplinger/Add-support-for-the-Hynix-Hi-846-camera/20210528-161549 base: git://linuxtv.org/media_tree.git master config: sh-allmodconfig (attached as .config) compiler: sh4-linux-gcc (GCC) 9.3.0 reproduce (this is a W=1 build): wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross # https://github.com/0day-ci/linux/commit/32f267bbcb6cfa4c157f7e105095d16244c01cb2 git remote add linux-review https://github.com/0day-ci/linux git fetch --no-tags linux-review Martin-Kepplinger/Add-support-for-the-Hynix-Hi-846-camera/20210528-161549 git checkout 32f267bbcb6cfa4c157f7e105095d16244c01cb2 # save the attached .config to linux build tree COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-9.3.0 make.cross ARCH=sh If you fix the issue, kindly add following tag as appropriate Reported-by: kernel test robot <lkp@intel.com> All errors (new ones prefixed by >>, old ones prefixed by <<): >> ERROR: modpost: "__divdi3" [drivers/media/i2c/hi846.ko] undefined! ERROR: modpost: "__delay" [drivers/net/mdio/mdio-cavium.ko] undefined! ERROR: modpost: "__udivdi3" [fs/btrfs/btrfs.ko] undefined! ERROR: modpost: "__umoddi3" [fs/btrfs/btrfs.ko] undefined! Kconfig warnings: (for reference only) WARNING: unmet direct dependencies detected for SND_ATMEL_SOC_PDC Depends on SOUND && !UML && SND && SND_SOC && SND_ATMEL_SOC && HAS_DMA Selected by - SND_ATMEL_SOC_SSC && SOUND && !UML && SND && SND_SOC && SND_ATMEL_SOC - SND_ATMEL_SOC_SSC_PDC && SOUND && !UML && SND && SND_SOC && SND_ATMEL_SOC && ATMEL_SSC --- 0-DAY CI Kernel Test Service, Intel Corporation https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org [-- Attachment #2: .config.gz --] [-- Type: application/gzip, Size: 54768 bytes --] ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v2 3/5] media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera @ 2021-05-28 19:08 ` kernel test robot 0 siblings, 0 replies; 18+ messages in thread From: kernel test robot @ 2021-05-28 19:08 UTC (permalink / raw) To: kbuild-all [-- Attachment #1: Type: text/plain, Size: 2249 bytes --] Hi Martin, I love your patch! Yet something to improve: [auto build test ERROR on linuxtv-media/master] [also build test ERROR on robh/for-next arm64/for-next/core linus/master v5.13-rc3 next-20210528] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in https://git-scm.com/docs/git-format-patch] url: https://github.com/0day-ci/linux/commits/Martin-Kepplinger/Add-support-for-the-Hynix-Hi-846-camera/20210528-161549 base: git://linuxtv.org/media_tree.git master config: sh-allmodconfig (attached as .config) compiler: sh4-linux-gcc (GCC) 9.3.0 reproduce (this is a W=1 build): wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross # https://github.com/0day-ci/linux/commit/32f267bbcb6cfa4c157f7e105095d16244c01cb2 git remote add linux-review https://github.com/0day-ci/linux git fetch --no-tags linux-review Martin-Kepplinger/Add-support-for-the-Hynix-Hi-846-camera/20210528-161549 git checkout 32f267bbcb6cfa4c157f7e105095d16244c01cb2 # save the attached .config to linux build tree COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-9.3.0 make.cross ARCH=sh If you fix the issue, kindly add following tag as appropriate Reported-by: kernel test robot <lkp@intel.com> All errors (new ones prefixed by >>, old ones prefixed by <<): >> ERROR: modpost: "__divdi3" [drivers/media/i2c/hi846.ko] undefined! ERROR: modpost: "__delay" [drivers/net/mdio/mdio-cavium.ko] undefined! ERROR: modpost: "__udivdi3" [fs/btrfs/btrfs.ko] undefined! ERROR: modpost: "__umoddi3" [fs/btrfs/btrfs.ko] undefined! Kconfig warnings: (for reference only) WARNING: unmet direct dependencies detected for SND_ATMEL_SOC_PDC Depends on SOUND && !UML && SND && SND_SOC && SND_ATMEL_SOC && HAS_DMA Selected by - SND_ATMEL_SOC_SSC && SOUND && !UML && SND && SND_SOC && SND_ATMEL_SOC - SND_ATMEL_SOC_SSC_PDC && SOUND && !UML && SND && SND_SOC && SND_ATMEL_SOC && ATMEL_SSC --- 0-DAY CI Kernel Test Service, Intel Corporation https://lists.01.org/hyperkitty/list/kbuild-all(a)lists.01.org [-- Attachment #2: config.gz --] [-- Type: application/gzip, Size: 54768 bytes --] ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v2 3/5] media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera 2021-05-28 8:13 ` [PATCH v2 3/5] media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera Martin Kepplinger 2021-05-28 18:20 ` kernel test robot 2021-05-28 19:08 ` kernel test robot @ 2021-06-02 14:36 ` Sakari Ailus 2 siblings, 0 replies; 18+ messages in thread From: Sakari Ailus @ 2021-06-02 14:36 UTC (permalink / raw) To: Martin Kepplinger Cc: laurent.pinchart, mchehab, devicetree, kernel, krzysztof.kozlowski, linux-kernel, linux-media, paul.kocialkowski, robh, shawnx.tu Hi Martin, Thanks for the patch. On Fri, May 28, 2021 at 10:13:34AM +0200, Martin Kepplinger wrote: > The SK Hynix Hi-846 is a 1/4" 8M Pixel CMOS Image Sensor. It supports > usual features like I2C control, CSI-2 for frame data, digital/analog > gain control or test patterns. > > This driver supports the 640x480, 1280x720 and 1632x1224 resolution > modes. It supports runtime PM in order not to draw any unnecessary power. > > The part is also called YACG4D0C9SHC and a datasheet can be found at > https://product.skhynix.com/products/cis/cis.go > > The large sets of partly undocumented register values are for example > found when searching for the hi846_mipi_raw_Sensor.c Android driver. > > Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> > --- > MAINTAINERS | 6 + > drivers/media/i2c/Kconfig | 13 + > drivers/media/i2c/Makefile | 1 + > drivers/media/i2c/hi846.c | 2137 ++++++++++++++++++++++++++++++++++++ > 4 files changed, 2157 insertions(+) > create mode 100644 drivers/media/i2c/hi846.c > > diff --git a/MAINTAINERS b/MAINTAINERS > index 81e1edeceae4..b5ec5c66ec0e 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -8425,6 +8425,12 @@ S: Maintained > T: git git://linuxtv.org/media_tree.git > F: drivers/media/i2c/hi556.c > > +HYNIX HI846 SENSOR DRIVER > +M: Martin Kepplinger <martin.kepplinger@puri.sm> > +L: linux-media@vger.kernel.org > +S: Maintained > +F: drivers/media/i2c/hi846.c > + > Hyper-V/Azure CORE AND DRIVERS > M: "K. Y. Srinivasan" <kys@microsoft.com> > M: Haiyang Zhang <haiyangz@microsoft.com> > diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig > index 462c0e059754..f8cf5bf8eb68 100644 > --- a/drivers/media/i2c/Kconfig > +++ b/drivers/media/i2c/Kconfig > @@ -738,6 +738,19 @@ config VIDEO_HI556 > To compile this driver as a module, choose M here: the > module will be called hi556. > > +config VIDEO_HI846 > + tristate "Hynix Hi-846 sensor support" > + depends on I2C && VIDEO_V4L2 > + select MEDIA_CONTROLLER > + select VIDEO_V4L2_SUBDEV_API > + select V4L2_FWNODE > + help > + This is a Video4Linux2 sensor driver for the Hynix > + Hi-846 camera. > + > + To compile this driver as a module, choose M here: the > + module will be called hi846. > + > config VIDEO_IMX214 > tristate "Sony IMX214 sensor support" > depends on GPIOLIB && I2C && VIDEO_V4L2 > diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile > index 0c067beca066..1194c5e6708b 100644 > --- a/drivers/media/i2c/Makefile > +++ b/drivers/media/i2c/Makefile > @@ -116,6 +116,7 @@ obj-$(CONFIG_VIDEO_ML86V7667) += ml86v7667.o > obj-$(CONFIG_VIDEO_OV2659) += ov2659.o > obj-$(CONFIG_VIDEO_TC358743) += tc358743.o > obj-$(CONFIG_VIDEO_HI556) += hi556.o > +obj-$(CONFIG_VIDEO_HI846) += hi846.o > obj-$(CONFIG_VIDEO_IMX214) += imx214.o > obj-$(CONFIG_VIDEO_IMX219) += imx219.o > obj-$(CONFIG_VIDEO_IMX258) += imx258.o > diff --git a/drivers/media/i2c/hi846.c b/drivers/media/i2c/hi846.c > new file mode 100644 > index 000000000000..3f896e45f99a > --- /dev/null > +++ b/drivers/media/i2c/hi846.c > @@ -0,0 +1,2137 @@ > +// SPDX-License-Identifier: GPL-2.0 > +// Copyright (c) 2021 Purism SPC > + > +#include <asm/unaligned.h> > +#include <linux/clk.h> > +#include <linux/delay.h> > +#include <linux/gpio.h> > +#include <linux/i2c.h> > +#include <linux/module.h> > +#include <linux/of_gpio.h> > +#include <linux/of_graph.h> > +#include <linux/regulator/consumer.h> > +#include <linux/pm_runtime.h> > +#include <linux/pm.h> > +#include <media/v4l2-ctrls.h> > +#include <media/v4l2-device.h> > +#include <media/v4l2-fwnode.h> > + > + > +#define HI846_MEDIA_BUS_FORMAT MEDIA_BUS_FMT_SGBRG10_1X10 > +#define HI846_RGB_DEPTH 10 > +#define DEFAULT_FPS 30 > + > +/* Frame length lines / Vertical timings */ > +#define HI846_REG_FLL 0x0006 > +#define HI846_FLL_MAX 0xffff > + > +/* Horizontal timing */ > +#define HI846_REG_LLP 0x0008 > +#define HI846_LINE_LENGTH 3800 > + > +#define HI846_REG_BINNING_MODE 0x000c > + > +#define HI846_REG_IMAGE_ORIENTATION 0x000e > + > +#define HI846_REG_UNKNOWN_0022 0x0022 > + > +#define HI846_REG_Y_ADDR_START_VACT_H 0x0026 > +#define HI846_REG_Y_ADDR_START_VACT_L 0x0027 > +#define HI846_REG_UNKNOWN_0028 0x0028 > + > +#define HI846_REG_Y_ADDR_END_VACT_H 0x002c > +#define HI846_REG_Y_ADDR_END_VACT_L 0x002d > + > +#define HI846_REG_Y_ODD_INC_FOBP 0x002e > +#define HI846_REG_Y_EVEN_INC_FOBP 0x002f > + > +#define HI846_REG_Y_ODD_INC_VACT 0x0032 > +#define HI846_REG_Y_EVEN_INC_VACT 0x0033 > + > +#define HI846_REG_GROUPED_PARA_HOLD 0x0046 > + > +#define HI846_REG_TG_ENABLE 0x004c > + > +#define HI846_REG_UNKNOWN_005C 0x005c > + > +#define HI846_REG_UNKNOWN_006A 0x006a > + > +/* Long exposure time. Actually, exposure is a 20 bit value that > + * includes the lower 4 bits of 0x0073 too. only 16 bit are used > + * right now > + */ > +#define HI846_REG_EXPOSURE 0x0074 > +#define HI846_EXPOSURE_MIN 6 > +#define HI846_EXPOSURE_MAX_MARGIN 2 > +#define HI846_EXPOSURE_STEP 1 > + > +/* Analog gain controls from sensor */ > +#define HI846_REG_ANALOG_GAIN 0x0077 > +#define HI846_ANAL_GAIN_MIN 0 > +#define HI846_ANAL_GAIN_MAX 240 > +#define HI846_ANAL_GAIN_STEP 8 > + > +/* Digital gain controls from sensor */ > +#define HI846_REG_MWB_GR_GAIN_H 0x0078 > +#define HI846_REG_MWB_GR_GAIN_L 0x0079 > +#define HI846_REG_MWB_GB_GAIN_H 0x007a > +#define HI846_REG_MWB_GB_GAIN_L 0x007b > +#define HI846_REG_MWB_R_GAIN_H 0x007c > +#define HI846_REG_MWB_R_GAIN_L 0x007d > +#define HI846_REG_MWB_B_GAIN_H 0x007e > +#define HI846_REG_MWB_B_GAIN_L 0x007f > +#define HI846_DGTL_GAIN_MIN 0 > +#define HI846_DGTL_GAIN_MAX 8191 > +#define HI846_DGTL_GAIN_STEP 1 > +#define HI846_DGTL_GAIN_DEFAULT 256 > + > +#define HI846_REG_X_ADDR_START_HACT_H 0x0120 > +#define HI846_REG_X_ADDR_END_HACT_H 0x0122 > + > +#define HI846_REG_UNKNOWN_012A 0x012a > + > +#define HI846_REG_UNKNOWN_0200 0x0200 > + > +#define HI846_REG_UNKNOWN_021C 0x021c > +#define HI846_REG_UNKNOWN_021E 0x021e > + > +#define HI846_REG_UNKNOWN_0402 0x0402 > +#define HI846_REG_UNKNOWN_0404 0x0404 > +#define HI846_REG_UNKNOWN_0408 0x0408 > +#define HI846_REG_UNKNOWN_0410 0x0410 > +#define HI846_REG_UNKNOWN_0412 0x0412 > +#define HI846_REG_UNKNOWN_0414 0x0414 > + > +#define HI846_REG_UNKNOWN_0418 0x0418 > + > +#define HI846_REG_UNKNOWN_051E 0x051e > + > +/* Formatter */ > +#define HI846_REG_X_START_H 0x0804 > +#define HI846_REG_X_START_L 0x0805 > + > +/* MIPI */ > +#define HI846_REG_UNKNOWN_0900 0x0900 > +#define HI846_REG_MIPI_TX_OP_EN 0x0901 > +#define HI846_REG_MIPI_TX_OP_MODE 0x0902 > +#define HI846_RAW8 BIT(5) > + > +#define HI846_REG_UNKNOWN_090C 0x090c > +#define HI846_REG_UNKNOWN_090E 0x090e > + > +#define HI846_REG_UNKNOWN_0914 0x0914 > +#define HI846_REG_TLPX 0x0915 > +#define HI846_REG_TCLK_PREPARE 0x0916 > +#define HI846_REG_TCLK_ZERO 0x0917 > +#define HI846_REG_UNKNOWN_0918 0x0918 > +#define HI846_REG_THS_PREPARE 0x0919 > +#define HI846_REG_THS_ZERO 0x091a > +#define HI846_REG_THS_TRAIL 0x091b > +#define HI846_REG_TCLK_POST 0x091c > +#define HI846_REG_TCLK_TRAIL_MIN 0x091d > +#define HI846_REG_UNKNOWN_091E 0x091e > + > +#define HI846_REG_UNKNOWN_0954 0x0954 > +#define HI846_REG_UNKNOWN_0956 0x0956 > +#define HI846_REG_UNKNOWN_0958 0x0958 > +#define HI846_REG_UNKNOWN_095A 0x095a > + > +/* ISP Common */ > +#define HI846_REG_MODE_SELECT 0x0a00 > +#define HI846_MODE_STANDBY 0x00 > +#define HI846_MODE_STREAMING 0x01 > +#define HI846_REG_FAST_STANDBY_MODE 0x0a02 > +#define HI846_REG_ISP_EN_H 0x0a04 > + > +/* Test Pattern Control */ > +#define HI846_REG_ISP 0x0a05 > +#define HI846_REG_ISP_TPG_EN 0x01 > +#define HI846_REG_TEST_PATTERN 0x020a /* 1-9 */ > + > +#define HI846_REG_UNKNOWN_0A0C 0x0a0c > + > +/* Windowing */ > +#define HI846_REG_X_OUTPUT_SIZE_H 0x0a12 > +#define HI846_REG_X_OUTPUT_SIZE_L 0x0a13 > +#define HI846_REG_Y_OUTPUT_SIZE_H 0x0a14 > +#define HI846_REG_Y_OUTPUT_SIZE_L 0x0a15 > + > +/* ISP Common */ > +#define HI846_REG_PEDESTAL_EN 0x0a1a > + > +#define HI846_REG_UNKNOWN_0A1E 0x0a1e > + > +/* Horizontal Binning Mode */ > +#define HI846_REG_HBIN_MODE 0x0a22 > + > +#define HI846_REG_UNKNOWN_0A24 0x0a24 > +#define HI846_REG_UNKNOWN_0B02 0x0b02 > +#define HI846_REG_UNKNOWN_0B10 0x0b10 > +#define HI846_REG_UNKNOWN_0B12 0x0b12 > +#define HI846_REG_UNKNOWN_0B14 0x0b14 > + > +/* BLC (Black Level Calibration) */ > +#define HI846_REG_BLC_CTL0 0x0c00 > + > +#define HI846_REG_UNKNOWN_0C06 0x0c06 > +#define HI846_REG_UNKNOWN_0C10 0x0c10 > +#define HI846_REG_UNKNOWN_0C12 0x0c12 > +#define HI846_REG_UNKNOWN_0C14 0x0c14 > +#define HI846_REG_UNKNOWN_0C16 0x0c16 > + > +#define HI846_REG_UNKNOWN_0E04 0x0e04 > + > +#define HI846_REG_CHIP_ID_L 0x0f16 > +#define HI846_REG_CHIP_ID_H 0x0f17 > +#define HI846_CHIP_ID_L 0x46 > +#define HI846_CHIP_ID_H 0x08 > + > +#define HI846_REG_UNKNOWN_0F04 0x0f04 > +#define HI846_REG_UNKNOWN_0F08 0x0f08 > + > +/* PLL */ > +#define HI846_REG_PLL_CFG_MIPI2_H 0x0f2a > +#define HI846_REG_PLL_CFG_MIPI2_L 0x0f2b > + > +#define HI846_REG_UNKNOWN_0F30 0x0f30 > +#define HI846_REG_PLL_CFG_RAMP1_H 0x0f32 > +#define HI846_REG_UNKNOWN_0F36 0x0f36 > +#define HI846_REG_PLL_CFG_MIPI1_H 0x0f38 > + > +#define HI846_REG_UNKNOWN_2008 0x2008 > +#define HI846_REG_UNKNOWN_326E 0x326e > + > +struct hi846_reg { > + u16 address; > + u16 val; > +}; > + > +struct hi846_reg_list { > + u32 num_of_regs; > + const struct hi846_reg *regs; > +}; > + > +struct hi846_mode { > + /* Frame width in pixels */ > + u32 width; > + > + /* Frame height in pixels */ > + u32 height; > + > + /* Horizontal timing size */ > + u32 llp; > + > + /* Link frequency needed for this resolution */ > + u8 link_freq_index; > + > + u16 fps; > + > + /* vertical timining size */ > + u16 frame_len; > + > + const struct hi846_reg_list reg_list_config; > + const struct hi846_reg_list reg_list_2lane; > + const struct hi846_reg_list reg_list_4lane; > +}; > + > +#define to_hi846(_sd) container_of(_sd, struct hi846, sd) > + > +static const struct hi846_reg hi846_init_2lane[] = { > + {HI846_REG_MODE_SELECT, 0x0000}, > + /* regs below are unknown */ > + {0x2000, 0x100A}, > + {0x2002, 0x00FF}, > + {0x2004, 0x0007}, > + {0x2006, 0x3FFF}, > + {0x2008, 0x3FFF}, > + {0x200A, 0xC216}, > + {0x200C, 0x1292}, > + {0x200E, 0xC01A}, > + {0x2010, 0x403D}, > + {0x2012, 0x000E}, > + {0x2014, 0x403E}, > + {0x2016, 0x0B80}, > + {0x2018, 0x403F}, > + {0x201A, 0x82AE}, > + {0x201C, 0x1292}, > + {0x201E, 0xC00C}, > + {0x2020, 0x4130}, > + {0x2022, 0x43E2}, > + {0x2024, 0x0180}, > + {0x2026, 0x4130}, > + {0x2028, 0x7400}, > + {0x202A, 0x5000}, > + {0x202C, 0x0253}, > + {0x202E, 0x0AD1}, > + {0x2030, 0x2360}, > + {0x2032, 0x0009}, > + {0x2034, 0x5020}, > + {0x2036, 0x000B}, > + {0x2038, 0x0002}, > + {0x203A, 0x0044}, > + {0x203C, 0x0016}, > + {0x203E, 0x1792}, > + {0x2040, 0x7002}, > + {0x2042, 0x154F}, > + {0x2044, 0x00D5}, > + {0x2046, 0x000B}, > + {0x2048, 0x0019}, > + {0x204A, 0x1698}, > + {0x204C, 0x000E}, > + {0x204E, 0x099A}, > + {0x2050, 0x0058}, > + {0x2052, 0x7000}, > + {0x2054, 0x1799}, > + {0x2056, 0x0310}, > + {0x2058, 0x03C3}, > + {0x205A, 0x004C}, > + {0x205C, 0x064A}, > + {0x205E, 0x0001}, > + {0x2060, 0x0007}, > + {0x2062, 0x0BC7}, > + {0x2064, 0x0055}, > + {0x2066, 0x7000}, > + {0x2068, 0x1550}, > + {0x206A, 0x158A}, > + {0x206C, 0x0004}, > + {0x206E, 0x1488}, > + {0x2070, 0x7010}, > + {0x2072, 0x1508}, > + {0x2074, 0x0004}, > + {0x2076, 0x0016}, > + {0x2078, 0x03D5}, > + {0x207A, 0x0055}, > + {0x207C, 0x08CA}, > + {0x207E, 0x2019}, > + {0x2080, 0x0007}, > + {0x2082, 0x7057}, > + {0x2084, 0x0FC7}, > + {0x2086, 0x5041}, > + {0x2088, 0x12C8}, > + {0x208A, 0x5060}, > + {0x208C, 0x5080}, > + {0x208E, 0x2084}, > + {0x2090, 0x12C8}, > + {0x2092, 0x7800}, > + {0x2094, 0x0802}, > + {0x2096, 0x040F}, > + {0x2098, 0x1007}, > + {0x209A, 0x0803}, > + {0x209C, 0x080B}, > + {0x209E, 0x3803}, > + {0x20A0, 0x0807}, > + {0x20A2, 0x0404}, > + {0x20A4, 0x0400}, > + {0x20A6, 0xFFFF}, > + {0x20A8, 0xF0B2}, > + {0x20AA, 0xFFEF}, > + {0x20AC, 0x0A84}, > + {0x20AE, 0x1292}, > + {0x20B0, 0xC02E}, > + {0x20B2, 0x4130}, > + {0x23FE, 0xC056}, > + {0x3232, 0xFC0C}, > + {0x3236, 0xFC22}, > + {0x3248, 0xFCA8}, > + {0x326A, 0x8302}, > + {0x326C, 0x830A}, > + {0x326E, 0x0000}, > + {0x32CA, 0xFC28}, > + {0x32CC, 0xC3BC}, > + {0x32CE, 0xC34C}, > + {0x32D0, 0xC35A}, > + {0x32D2, 0xC368}, > + {0x32D4, 0xC376}, > + {0x32D6, 0xC3C2}, > + {0x32D8, 0xC3E6}, > + {0x32DA, 0x0003}, > + {0x32DC, 0x0003}, > + {0x32DE, 0x00C7}, > + {0x32E0, 0x0031}, > + {0x32E2, 0x0031}, > + {0x32E4, 0x0031}, > + {0x32E6, 0xFC28}, > + {0x32E8, 0xC3BC}, > + {0x32EA, 0xC384}, > + {0x32EC, 0xC392}, > + {0x32EE, 0xC3A0}, > + {0x32F0, 0xC3AE}, > + {0x32F2, 0xC3C4}, > + {0x32F4, 0xC3E6}, > + {0x32F6, 0x0003}, > + {0x32F8, 0x0003}, > + {0x32FA, 0x00C7}, > + {0x32FC, 0x0031}, > + {0x32FE, 0x0031}, > + {0x3300, 0x0031}, > + {0x3302, 0x82CA}, > + {0x3304, 0xC164}, > + {0x3306, 0x82E6}, > + {0x3308, 0xC19C}, > + {0x330A, 0x001F}, > + {0x330C, 0x001A}, > + {0x330E, 0x0034}, > + {0x3310, 0x0000}, > + {0x3312, 0x0000}, > + {0x3314, 0xFC94}, > + {0x3316, 0xC3D8}, > + /* regs above are unknown */ > + {HI846_REG_MODE_SELECT, 0x0000}, > + {HI846_REG_UNKNOWN_0E04, 0x0012}, > + {HI846_REG_Y_ODD_INC_FOBP, 0x1111}, > + {HI846_REG_Y_ODD_INC_VACT, 0x1111}, > + {HI846_REG_UNKNOWN_0022, 0x0008}, > + {HI846_REG_Y_ADDR_START_VACT_H, 0x0040}, > + {HI846_REG_UNKNOWN_0028, 0x0017}, > + {HI846_REG_Y_ADDR_END_VACT_H, 0x09CF}, > + {HI846_REG_UNKNOWN_005C, 0x2101}, > + {HI846_REG_FLL, 0x09DE}, > + {HI846_REG_LLP, 0x0ED8}, > + {HI846_REG_IMAGE_ORIENTATION, 0x0100}, > + {HI846_REG_BINNING_MODE, 0x0022}, > + {HI846_REG_HBIN_MODE, 0x0000}, > + {HI846_REG_UNKNOWN_0A24, 0x0000}, > + {HI846_REG_X_START_H, 0x0000}, > + {HI846_REG_X_OUTPUT_SIZE_H, 0x0CC0}, > + {HI846_REG_Y_OUTPUT_SIZE_H, 0x0990}, > + {HI846_REG_EXPOSURE, 0x09D8}, > + {HI846_REG_ANALOG_GAIN, 0x0000}, > + {HI846_REG_GROUPED_PARA_HOLD, 0x0000}, > + {HI846_REG_UNKNOWN_051E, 0x0000}, > + {HI846_REG_UNKNOWN_0200, 0x0400}, > + {HI846_REG_PEDESTAL_EN, 0x0C00}, > + {HI846_REG_UNKNOWN_0A0C, 0x0010}, > + {HI846_REG_UNKNOWN_0A1E, 0x0CCF}, > + {HI846_REG_UNKNOWN_0402, 0x0110}, > + {HI846_REG_UNKNOWN_0404, 0x00F4}, > + {HI846_REG_UNKNOWN_0408, 0x0000}, > + {HI846_REG_UNKNOWN_0410, 0x008D}, > + {HI846_REG_UNKNOWN_0412, 0x011A}, > + {HI846_REG_UNKNOWN_0414, 0x864C}, > + {HI846_REG_UNKNOWN_021C, 0x0003}, > + {HI846_REG_UNKNOWN_021E, 0x0235}, > + {HI846_REG_BLC_CTL0, 0x9150}, > + {HI846_REG_UNKNOWN_0C06, 0x0021}, > + {HI846_REG_UNKNOWN_0C10, 0x0040}, > + {HI846_REG_UNKNOWN_0C12, 0x0040}, > + {HI846_REG_UNKNOWN_0C14, 0x0040}, > + {HI846_REG_UNKNOWN_0C16, 0x0040}, > + {HI846_REG_FAST_STANDBY_MODE, 0x0100}, > + {HI846_REG_ISP_EN_H, 0x014A}, > + {HI846_REG_UNKNOWN_0418, 0x0000}, > + {HI846_REG_UNKNOWN_012A, 0x03B4}, > + {HI846_REG_X_ADDR_START_HACT_H, 0x0046}, > + {HI846_REG_X_ADDR_END_HACT_H, 0x0376}, > + {HI846_REG_UNKNOWN_0B02, 0xE04D}, > + {HI846_REG_UNKNOWN_0B10, 0x6821}, > + {HI846_REG_UNKNOWN_0B12, 0x0120}, > + {HI846_REG_UNKNOWN_0B14, 0x0001}, > + {HI846_REG_UNKNOWN_2008, 0x38FD}, > + {HI846_REG_UNKNOWN_326E, 0x0000}, > + {HI846_REG_UNKNOWN_0900, 0x0320}, > + {HI846_REG_MIPI_TX_OP_MODE, 0xC31A}, > + {HI846_REG_UNKNOWN_0914, 0xC109}, > + {HI846_REG_TCLK_PREPARE, 0x061A}, > + {HI846_REG_UNKNOWN_0918, 0x0306}, > + {HI846_REG_THS_ZERO, 0x0B09}, > + {HI846_REG_TCLK_POST, 0x0C07}, > + {HI846_REG_UNKNOWN_091E, 0x0A00}, > + {HI846_REG_UNKNOWN_090C, 0x042A}, > + {HI846_REG_UNKNOWN_090E, 0x006B}, > + {HI846_REG_UNKNOWN_0954, 0x0089}, > + {HI846_REG_UNKNOWN_0956, 0x0000}, > + {HI846_REG_UNKNOWN_0958, 0xCA00}, > + {HI846_REG_UNKNOWN_095A, 0x9240}, > + {HI846_REG_UNKNOWN_0F08, 0x2F04}, > + {HI846_REG_UNKNOWN_0F30, 0x001F}, > + {HI846_REG_UNKNOWN_0F36, 0x001F}, > + {HI846_REG_UNKNOWN_0F04, 0x3A00}, > + {HI846_REG_PLL_CFG_RAMP1_H, 0x025A}, > + {HI846_REG_PLL_CFG_MIPI1_H, 0x025A}, > + {HI846_REG_PLL_CFG_MIPI2_H, 0x0024}, > + {HI846_REG_UNKNOWN_006A, 0x0100}, > + {HI846_REG_TG_ENABLE, 0x0100}, > +}; > + > +static const struct hi846_reg hi846_init_4lane[] = { > + {0x2000, 0x987A}, > + {0x2002, 0x00FF}, > + {0x2004, 0x0047}, > + {0x2006, 0x3FFF}, > + {0x2008, 0x3FFF}, > + {0x200A, 0xC216}, > + {0x200C, 0x1292}, > + {0x200E, 0xC01A}, > + {0x2010, 0x403D}, > + {0x2012, 0x000E}, > + {0x2014, 0x403E}, > + {0x2016, 0x0B80}, > + {0x2018, 0x403F}, > + {0x201A, 0x82AE}, > + {0x201C, 0x1292}, > + {0x201E, 0xC00C}, > + {0x2020, 0x4130}, > + {0x2022, 0x43E2}, > + {0x2024, 0x0180}, > + {0x2026, 0x4130}, > + {0x2028, 0x7400}, > + {0x202A, 0x5000}, > + {0x202C, 0x0253}, > + {0x202E, 0x0AD1}, > + {0x2030, 0x2360}, > + {0x2032, 0x0009}, > + {0x2034, 0x5020}, > + {0x2036, 0x000B}, > + {0x2038, 0x0002}, > + {0x203A, 0x0044}, > + {0x203C, 0x0016}, > + {0x203E, 0x1792}, > + {0x2040, 0x7002}, > + {0x2042, 0x154F}, > + {0x2044, 0x00D5}, > + {0x2046, 0x000B}, > + {0x2048, 0x0019}, > + {0x204A, 0x1698}, > + {0x204C, 0x000E}, > + {0x204E, 0x099A}, > + {0x2050, 0x0058}, > + {0x2052, 0x7000}, > + {0x2054, 0x1799}, > + {0x2056, 0x0310}, > + {0x2058, 0x03C3}, > + {0x205A, 0x004C}, > + {0x205C, 0x064A}, > + {0x205E, 0x0001}, > + {0x2060, 0x0007}, > + {0x2062, 0x0BC7}, > + {0x2064, 0x0055}, > + {0x2066, 0x7000}, > + {0x2068, 0x1550}, > + {0x206A, 0x158A}, > + {0x206C, 0x0004}, > + {0x206E, 0x1488}, > + {0x2070, 0x7010}, > + {0x2072, 0x1508}, > + {0x2074, 0x0004}, > + {0x2076, 0x0016}, > + {0x2078, 0x03D5}, > + {0x207A, 0x0055}, > + {0x207C, 0x08CA}, > + {0x207E, 0x2019}, > + {0x2080, 0x0007}, > + {0x2082, 0x7057}, > + {0x2084, 0x0FC7}, > + {0x2086, 0x5041}, > + {0x2088, 0x12C8}, > + {0x208A, 0x5060}, > + {0x208C, 0x5080}, > + {0x208E, 0x2084}, > + {0x2090, 0x12C8}, > + {0x2092, 0x7800}, > + {0x2094, 0x0802}, > + {0x2096, 0x040F}, > + {0x2098, 0x1007}, > + {0x209A, 0x0803}, > + {0x209C, 0x080B}, > + {0x209E, 0x3803}, > + {0x20A0, 0x0807}, > + {0x20A2, 0x0404}, > + {0x20A4, 0x0400}, > + {0x20A6, 0xFFFF}, > + {0x20A8, 0xF0B2}, > + {0x20AA, 0xFFEF}, > + {0x20AC, 0x0A84}, > + {0x20AE, 0x1292}, > + {0x20B0, 0xC02E}, > + {0x20B2, 0x4130}, > + {0x20B4, 0xF0B2}, > + {0x20B6, 0xFFBF}, > + {0x20B8, 0x2004}, > + {0x20BA, 0x403F}, > + {0x20BC, 0x00C3}, > + {0x20BE, 0x4FE2}, > + {0x20C0, 0x8318}, > + {0x20C2, 0x43CF}, > + {0x20C4, 0x0000}, > + {0x20C6, 0x9382}, > + {0x20C8, 0xC314}, > + {0x20CA, 0x2003}, > + {0x20CC, 0x12B0}, > + {0x20CE, 0xCAB0}, > + {0x20D0, 0x4130}, > + {0x20D2, 0x12B0}, > + {0x20D4, 0xC90A}, > + {0x20D6, 0x4130}, > + {0x20D8, 0x42D2}, > + {0x20DA, 0x8318}, > + {0x20DC, 0x00C3}, > + {0x20DE, 0x9382}, > + {0x20E0, 0xC314}, > + {0x20E2, 0x2009}, > + {0x20E4, 0x120B}, > + {0x20E6, 0x120A}, > + {0x20E8, 0x1209}, > + {0x20EA, 0x1208}, > + {0x20EC, 0x1207}, > + {0x20EE, 0x1206}, > + {0x20F0, 0x4030}, > + {0x20F2, 0xC15E}, > + {0x20F4, 0x4130}, > + {0x20F6, 0x1292}, > + {0x20F8, 0xC008}, > + {0x20FA, 0x4130}, > + {0x20FC, 0x42D2}, > + {0x20FE, 0x82A1}, > + {0x2100, 0x00C2}, > + {0x2102, 0x1292}, > + {0x2104, 0xC040}, > + {0x2106, 0x4130}, > + {0x2108, 0x1292}, > + {0x210A, 0xC006}, > + {0x210C, 0x42A2}, > + {0x210E, 0x7324}, > + {0x2110, 0x9382}, > + {0x2112, 0xC314}, > + {0x2114, 0x2011}, > + {0x2116, 0x425F}, > + {0x2118, 0x82A1}, > + {0x211A, 0xF25F}, > + {0x211C, 0x00C1}, > + {0x211E, 0xF35F}, > + {0x2120, 0x2406}, > + {0x2122, 0x425F}, > + {0x2124, 0x00C0}, > + {0x2126, 0xF37F}, > + {0x2128, 0x522F}, > + {0x212A, 0x4F82}, > + {0x212C, 0x7324}, > + {0x212E, 0x425F}, > + {0x2130, 0x82D4}, > + {0x2132, 0xF35F}, > + {0x2134, 0x4FC2}, > + {0x2136, 0x01B3}, > + {0x2138, 0x93C2}, > + {0x213A, 0x829F}, > + {0x213C, 0x2421}, > + {0x213E, 0x403E}, > + {0x2140, 0xFFFE}, > + {0x2142, 0x40B2}, > + {0x2144, 0xEC78}, > + {0x2146, 0x831C}, > + {0x2148, 0x40B2}, > + {0x214A, 0xEC78}, > + {0x214C, 0x831E}, > + {0x214E, 0x40B2}, > + {0x2150, 0xEC78}, > + {0x2152, 0x8320}, > + {0x2154, 0xB3D2}, > + {0x2156, 0x008C}, > + {0x2158, 0x2405}, > + {0x215A, 0x4E0F}, > + {0x215C, 0x503F}, > + {0x215E, 0xFFD8}, > + {0x2160, 0x4F82}, > + {0x2162, 0x831C}, > + {0x2164, 0x90F2}, > + {0x2166, 0x0003}, > + {0x2168, 0x008C}, > + {0x216A, 0x2401}, > + {0x216C, 0x4130}, > + {0x216E, 0x421F}, > + {0x2170, 0x831C}, > + {0x2172, 0x5E0F}, > + {0x2174, 0x4F82}, > + {0x2176, 0x831E}, > + {0x2178, 0x5E0F}, > + {0x217A, 0x4F82}, > + {0x217C, 0x8320}, > + {0x217E, 0x3FF6}, > + {0x2180, 0x432E}, > + {0x2182, 0x3FDF}, > + {0x2184, 0x421F}, > + {0x2186, 0x7100}, > + {0x2188, 0x4F0E}, > + {0x218A, 0x503E}, > + {0x218C, 0xFFD8}, > + {0x218E, 0x4E82}, > + {0x2190, 0x7A04}, > + {0x2192, 0x421E}, > + {0x2194, 0x831C}, > + {0x2196, 0x5F0E}, > + {0x2198, 0x4E82}, > + {0x219A, 0x7A06}, > + {0x219C, 0x0B00}, > + {0x219E, 0x7304}, > + {0x21A0, 0x0050}, > + {0x21A2, 0x40B2}, > + {0x21A4, 0xD081}, > + {0x21A6, 0x0B88}, > + {0x21A8, 0x421E}, > + {0x21AA, 0x831E}, > + {0x21AC, 0x5F0E}, > + {0x21AE, 0x4E82}, > + {0x21B0, 0x7A0E}, > + {0x21B2, 0x521F}, > + {0x21B4, 0x8320}, > + {0x21B6, 0x4F82}, > + {0x21B8, 0x7A10}, > + {0x21BA, 0x0B00}, > + {0x21BC, 0x7304}, > + {0x21BE, 0x007A}, > + {0x21C0, 0x40B2}, > + {0x21C2, 0x0081}, > + {0x21C4, 0x0B88}, > + {0x21C6, 0x4392}, > + {0x21C8, 0x7A0A}, > + {0x21CA, 0x0800}, > + {0x21CC, 0x7A0C}, > + {0x21CE, 0x0B00}, > + {0x21D0, 0x7304}, > + {0x21D2, 0x022B}, > + {0x21D4, 0x40B2}, > + {0x21D6, 0xD081}, > + {0x21D8, 0x0B88}, > + {0x21DA, 0x0B00}, > + {0x21DC, 0x7304}, > + {0x21DE, 0x0255}, > + {0x21E0, 0x40B2}, > + {0x21E2, 0x0081}, > + {0x21E4, 0x0B88}, > + {0x21E6, 0x4130}, > + {0x23FE, 0xC056}, > + {0x3232, 0xFC0C}, > + {0x3236, 0xFC22}, > + {0x3238, 0xFCFC}, > + {0x323A, 0xFD84}, > + {0x323C, 0xFD08}, > + {0x3246, 0xFCD8}, > + {0x3248, 0xFCA8}, > + {0x324E, 0xFCB4}, > + {0x326A, 0x8302}, > + {0x326C, 0x830A}, > + {0x326E, 0x0000}, > + {0x32CA, 0xFC28}, > + {0x32CC, 0xC3BC}, > + {0x32CE, 0xC34C}, > + {0x32D0, 0xC35A}, > + {0x32D2, 0xC368}, > + {0x32D4, 0xC376}, > + {0x32D6, 0xC3C2}, > + {0x32D8, 0xC3E6}, > + {0x32DA, 0x0003}, > + {0x32DC, 0x0003}, > + {0x32DE, 0x00C7}, > + {0x32E0, 0x0031}, > + {0x32E2, 0x0031}, > + {0x32E4, 0x0031}, > + {0x32E6, 0xFC28}, > + {0x32E8, 0xC3BC}, > + {0x32EA, 0xC384}, > + {0x32EC, 0xC392}, > + {0x32EE, 0xC3A0}, > + {0x32F0, 0xC3AE}, > + {0x32F2, 0xC3C4}, > + {0x32F4, 0xC3E6}, > + {0x32F6, 0x0003}, > + {0x32F8, 0x0003}, > + {0x32FA, 0x00C7}, > + {0x32FC, 0x0031}, > + {0x32FE, 0x0031}, > + {0x3300, 0x0031}, > + {0x3302, 0x82CA}, > + {0x3304, 0xC164}, > + {0x3306, 0x82E6}, > + {0x3308, 0xC19C}, > + {0x330A, 0x001F}, > + {0x330C, 0x001A}, > + {0x330E, 0x0034}, > + {0x3310, 0x0000}, > + {0x3312, 0x0000}, > + {0x3314, 0xFC94}, > + {0x3316, 0xC3D8}, > + > + {0x0A00, 0x0000}, > + {0x0E04, 0x0012}, > + {0x002E, 0x1111}, > + {0x0032, 0x1111}, > + {0x0022, 0x0008}, > + {0x0026, 0x0040}, > + {0x0028, 0x0017}, > + {0x002C, 0x09CF}, > + {0x005C, 0x2101}, > + {0x0006, 0x09DE}, > + {0x0008, 0x0ED8}, > + {0x000E, 0x0100}, > + {0x000C, 0x0022}, > + {0x0A22, 0x0000}, > + {0x0A24, 0x0000}, > + {0x0804, 0x0000}, > + {0x0A12, 0x0CC0}, > + {0x0A14, 0x0990}, > + {0x0074, 0x09D8}, > + {0x0076, 0x0000}, > + {0x051E, 0x0000}, > + {0x0200, 0x0400}, > + {0x0A1A, 0x0C00}, > + {0x0A0C, 0x0010}, > + {0x0A1E, 0x0CCF}, > + {0x0402, 0x0110}, > + {0x0404, 0x00F4}, > + {0x0408, 0x0000}, > + {0x0410, 0x008D}, > + {0x0412, 0x011A}, > + {0x0414, 0x864C}, > + /* For OTP */ > + {0x021C, 0x0003}, > + {0x021E, 0x0235}, > + /* For OTP */ > + {0x0C00, 0x9950}, > + {0x0C06, 0x0021}, > + {0x0C10, 0x0040}, > + {0x0C12, 0x0040}, > + {0x0C14, 0x0040}, > + {0x0C16, 0x0040}, > + {0x0A02, 0x0100}, > + {0x0A04, 0x015A}, > + {0x0418, 0x0000}, > + {0x0128, 0x0028}, > + {0x012A, 0xFFFF}, > + {0x0120, 0x0046}, > + {0x0122, 0x0376}, > + {0x012C, 0x0020}, > + {0x012E, 0xFFFF}, > + {0x0124, 0x0040}, > + {0x0126, 0x0378}, > + {0x0746, 0x0050}, > + {0x0748, 0x01D5}, > + {0x074A, 0x022B}, > + {0x074C, 0x03B0}, > + {0x0756, 0x043F}, > + {0x0758, 0x3F1D}, > + {0x0B02, 0xE04D}, > + {0x0B10, 0x6821}, > + {0x0B12, 0x0120}, > + {0x0B14, 0x0001}, > + {0x2008, 0x38FD}, > + {0x326E, 0x0000}, > + {0x0900, 0x0300}, > + {0x0902, 0xC319}, > + {0x0914, 0xC109}, > + {0x0916, 0x061A}, > + {0x0918, 0x0407}, > + {0x091A, 0x0A0B}, > + {0x091C, 0x0E08}, > + {0x091E, 0x0A00}, > + {0x090C, 0x0427}, > + {0x090E, 0x0059}, > + {0x0954, 0x0089}, > + {0x0956, 0x0000}, > + {0x0958, 0xCA80}, > + {0x095A, 0x9240}, > + {0x0F08, 0x2F04}, > + {0x0F30, 0x001F}, > + {0x0F36, 0x001F}, > + {0x0F04, 0x3A00}, > + {0x0F32, 0x025A}, > + {0x0F38, 0x025A}, > + {0x0F2A, 0x4124}, > + {0x006A, 0x0100}, > + {0x004C, 0x0100}, > + {0x0044, 0x0001}, > +}; > + > +static const struct hi846_reg mode_640x480_config[] = { > + {HI846_REG_MODE_SELECT, 0x0000}, > + {HI846_REG_Y_ODD_INC_FOBP, 0x7711}, > + {HI846_REG_Y_ODD_INC_VACT, 0x7711}, > + {HI846_REG_Y_ADDR_START_VACT_H, 0x0148}, > + {HI846_REG_Y_ADDR_END_VACT_H, 0x08C7}, > + {HI846_REG_UNKNOWN_005C, 0x4404}, > + {HI846_REG_FLL, 0x0277}, > + {HI846_REG_LLP, 0x0ED8}, > + {HI846_REG_BINNING_MODE, 0x0322}, > + {HI846_REG_HBIN_MODE, 0x0200}, > + {HI846_REG_UNKNOWN_0A24, 0x0000}, > + {HI846_REG_X_START_H, 0x0058}, > + {HI846_REG_X_OUTPUT_SIZE_H, 0x0280}, > + {HI846_REG_Y_OUTPUT_SIZE_H, 0x01E0}, > + > + /* For OTP */ > + {HI846_REG_UNKNOWN_021C, 0x0003}, > + {HI846_REG_UNKNOWN_021E, 0x0235}, > + > + {HI846_REG_ISP_EN_H, 0x017A}, > + {HI846_REG_UNKNOWN_0418, 0x0210}, > + {HI846_REG_UNKNOWN_0B02, 0xE04D}, > + {HI846_REG_UNKNOWN_0B10, 0x7021}, > + {HI846_REG_UNKNOWN_0B12, 0x0120}, > + {HI846_REG_UNKNOWN_0B14, 0x0001}, > + {HI846_REG_UNKNOWN_2008, 0x38FD}, > + {HI846_REG_UNKNOWN_326E, 0x0000}, > +}; > + > +static const struct hi846_reg mode_640x480_mipi_2lane[] = { > + {HI846_REG_UNKNOWN_0900, 0x0300}, > + {HI846_REG_MIPI_TX_OP_MODE, 0x4319}, > + {HI846_REG_UNKNOWN_0914, 0xC105}, > + {HI846_REG_TCLK_PREPARE, 0x030C}, > + {HI846_REG_UNKNOWN_0918, 0x0304}, > + {HI846_REG_THS_ZERO, 0x0708}, > + {HI846_REG_TCLK_POST, 0x0B04}, > + {HI846_REG_UNKNOWN_091E, 0x0500}, > + {HI846_REG_UNKNOWN_090C, 0x0208}, > + {HI846_REG_UNKNOWN_090E, 0x009A}, > + {HI846_REG_UNKNOWN_0954, 0x0089}, > + {HI846_REG_UNKNOWN_0956, 0x0000}, > + {HI846_REG_UNKNOWN_0958, 0xCA80}, > + {HI846_REG_UNKNOWN_095A, 0x9240}, > + {HI846_REG_PLL_CFG_MIPI2_H, 0x4924}, > + {HI846_REG_TG_ENABLE, 0x0100}, > +}; > + > +static const struct hi846_reg mode_1280x720_config[] = { > + {HI846_REG_MODE_SELECT, 0x0000}, > + {HI846_REG_Y_ODD_INC_FOBP, 0x3311}, > + {HI846_REG_Y_ODD_INC_VACT, 0x3311}, > + {HI846_REG_Y_ADDR_START_VACT_H, 0x0238}, > + {HI846_REG_Y_ADDR_END_VACT_H, 0x07D7}, > + {HI846_REG_UNKNOWN_005C, 0x4202}, > + {HI846_REG_FLL, 0x034A}, > + {HI846_REG_LLP, 0x0ED8}, > + {HI846_REG_BINNING_MODE, 0x0122}, > + {HI846_REG_HBIN_MODE, 0x0100}, > + {HI846_REG_UNKNOWN_0A24, 0x0000}, > + {HI846_REG_X_START_H, 0x00B0}, > + {HI846_REG_X_OUTPUT_SIZE_H, 0x0500}, > + {HI846_REG_Y_OUTPUT_SIZE_H, 0x02D0}, > + {HI846_REG_EXPOSURE, 0x0344}, > + > + /* For OTP */ > + {HI846_REG_UNKNOWN_021C, 0x0003}, > + {HI846_REG_UNKNOWN_021E, 0x0235}, > + > + {HI846_REG_ISP_EN_H, 0x017A}, > + {HI846_REG_UNKNOWN_0418, 0x0410}, > + {HI846_REG_UNKNOWN_0B02, 0xE04D}, > + {HI846_REG_UNKNOWN_0B10, 0x6C21}, > + {HI846_REG_UNKNOWN_0B12, 0x0120}, > + {HI846_REG_UNKNOWN_0B14, 0x0005}, > + {HI846_REG_UNKNOWN_2008, 0x38FD}, > + {HI846_REG_UNKNOWN_326E, 0x0000}, > +}; > + > +static const struct hi846_reg mode_1280x720_mipi_2lane[] = { > + {HI846_REG_UNKNOWN_0900, 0x0300}, > + {HI846_REG_MIPI_TX_OP_MODE, 0x4319}, > + {HI846_REG_UNKNOWN_0914, 0xC109}, > + {HI846_REG_TCLK_PREPARE, 0x061A}, > + {HI846_REG_UNKNOWN_0918, 0x0407}, > + {HI846_REG_THS_ZERO, 0x0A0B}, > + {HI846_REG_TCLK_POST, 0x0E08}, > + {HI846_REG_UNKNOWN_091E, 0x0A00}, > + {HI846_REG_UNKNOWN_090C, 0x0427}, > + {HI846_REG_UNKNOWN_090E, 0x0145}, > + {HI846_REG_UNKNOWN_0954, 0x0089}, > + {HI846_REG_UNKNOWN_0956, 0x0000}, > + {HI846_REG_UNKNOWN_0958, 0xCA80}, > + {HI846_REG_UNKNOWN_095A, 0x9240}, > + {HI846_REG_PLL_CFG_MIPI2_H, 0x4124}, > + {HI846_REG_TG_ENABLE, 0x0100}, > +}; > + > +static const struct hi846_reg mode_1280x720_mipi_4lane[] = { > + /* 360Mbps */ > + {HI846_REG_UNKNOWN_0900, 0x0300}, > + {HI846_REG_MIPI_TX_OP_MODE, 0xC319}, > + {HI846_REG_UNKNOWN_0914, 0xC105}, > + {HI846_REG_TCLK_PREPARE, 0x030C}, > + {HI846_REG_UNKNOWN_0918, 0x0304}, > + {HI846_REG_THS_ZERO, 0x0708}, > + {HI846_REG_TCLK_POST, 0x0B04}, > + {HI846_REG_UNKNOWN_091E, 0x0500}, > + {HI846_REG_UNKNOWN_090C, 0x0208}, > + {HI846_REG_UNKNOWN_090E, 0x008A}, > + {HI846_REG_UNKNOWN_0954, 0x0089}, > + {HI846_REG_UNKNOWN_0956, 0x0000}, > + {HI846_REG_UNKNOWN_0958, 0xCA80}, > + {HI846_REG_UNKNOWN_095A, 0x9240}, > + {HI846_REG_PLL_CFG_MIPI2_H, 0x4924}, > + {HI846_REG_TG_ENABLE, 0x0100}, > +}; > + > +static const struct hi846_reg mode_1632x1224_config[] = { > + {HI846_REG_MODE_SELECT, 0x0000}, > + {HI846_REG_Y_ODD_INC_FOBP, 0x3311}, > + {HI846_REG_Y_ODD_INC_VACT, 0x3311}, > + {HI846_REG_Y_ADDR_START_VACT_H, 0x0040}, > + {HI846_REG_Y_ADDR_END_VACT_H, 0x09CF}, > + {HI846_REG_UNKNOWN_005C, 0x4202}, > + {HI846_REG_FLL, 0x09DE}, > + {HI846_REG_LLP, 0x0ED8}, > + {HI846_REG_BINNING_MODE, 0x0122}, > + {HI846_REG_HBIN_MODE, 0x0100}, > + {HI846_REG_UNKNOWN_0A24, 0x0000}, > + {HI846_REG_X_START_H, 0x0000}, > + {HI846_REG_X_OUTPUT_SIZE_H, 0x0660}, > + {HI846_REG_Y_OUTPUT_SIZE_H, 0x04C8}, > + {HI846_REG_EXPOSURE, 0x09D8}, > + {HI846_REG_ISP_EN_H, 0x017A}, > + > + /* For OTP */ > + {HI846_REG_UNKNOWN_021C, 0x0003}, > + {HI846_REG_UNKNOWN_021E, 0x0235}, > + > + {HI846_REG_UNKNOWN_0418, 0x0000}, > + {HI846_REG_UNKNOWN_0B02, 0xE04D}, > + {HI846_REG_UNKNOWN_0B10, 0x6C21}, > + {HI846_REG_UNKNOWN_0B12, 0x0120}, > + {HI846_REG_UNKNOWN_0B14, 0x0005}, > + {HI846_REG_UNKNOWN_2008, 0x38FD}, > + {HI846_REG_UNKNOWN_326E, 0x0000}, > +}; > + > +static const struct hi846_reg mode_1632x1224_mipi_2lane[] = { > + {HI846_REG_UNKNOWN_0900, 0x0300}, > + {HI846_REG_MIPI_TX_OP_MODE, 0x4319}, > + {HI846_REG_UNKNOWN_0914, 0xC109}, > + {HI846_REG_TCLK_PREPARE, 0x061A}, > + {HI846_REG_UNKNOWN_0918, 0x0407}, > + {HI846_REG_THS_ZERO, 0x0A0B}, > + {HI846_REG_TCLK_POST, 0x0E08}, > + {HI846_REG_UNKNOWN_091E, 0x0A00}, > + {HI846_REG_UNKNOWN_090C, 0x0427}, > + {HI846_REG_UNKNOWN_090E, 0x0069}, > + {HI846_REG_UNKNOWN_0954, 0x0089}, > + {HI846_REG_UNKNOWN_0956, 0x0000}, > + {HI846_REG_UNKNOWN_0958, 0xCA80}, > + {HI846_REG_UNKNOWN_095A, 0x9240}, > + {HI846_REG_PLL_CFG_MIPI2_H, 0x4124}, > + {HI846_REG_TG_ENABLE, 0x0100}, > +}; > + > +static const struct hi846_reg mode_1632x1224_mipi_4lane[] = { > + {HI846_REG_UNKNOWN_0900, 0x0300}, > + {HI846_REG_MIPI_TX_OP_MODE, 0xC319}, > + {HI846_REG_UNKNOWN_0914, 0xC105}, > + {HI846_REG_TCLK_PREPARE, 0x030C}, > + {HI846_REG_UNKNOWN_0918, 0x0304}, > + {HI846_REG_THS_ZERO, 0x0708}, > + {HI846_REG_TCLK_POST, 0x0B04}, > + {HI846_REG_UNKNOWN_091E, 0x0500}, > + {HI846_REG_UNKNOWN_090C, 0x0208}, > + {HI846_REG_UNKNOWN_090E, 0x001C}, > + {HI846_REG_UNKNOWN_0954, 0x0089}, > + {HI846_REG_UNKNOWN_0956, 0x0000}, > + {HI846_REG_UNKNOWN_0958, 0xCA80}, > + {HI846_REG_UNKNOWN_095A, 0x9240}, > + {HI846_REG_PLL_CFG_MIPI2_H, 0x4924}, > + {HI846_REG_TG_ENABLE, 0x0100}, > +}; > + > +static const char * const hi846_test_pattern_menu[] = { > + "Disabled", > + "Solid Colour", > + "100% Colour Bars", > + "Fade To Grey Colour Bars", > + "PN9", > + "Gradient Horizontal", > + "Gradient Vertical", > + "Check Board", > + "Slant Pattern", > + "Resolution Pattern", > +}; > + > +#define FREQ_INDEX_640 0 > +#define FREQ_INDEX_1280 1 > +static const s64 hi846_link_freqs[] = { > + [FREQ_INDEX_640] = 80000000, > + [FREQ_INDEX_1280] = 200000000, > +}; > + > +static const struct hi846_reg_list hi846_init_regs_list_2lane = { > + .num_of_regs = ARRAY_SIZE(hi846_init_2lane), > + .regs = hi846_init_2lane, > +}; > + > +static const struct hi846_reg_list hi846_init_regs_list_4lane = { > + .num_of_regs = ARRAY_SIZE(hi846_init_4lane), > + .regs = hi846_init_4lane, > +}; > + > +static const struct hi846_mode supported_modes[] = { > + { > + .width = 640, > + .height = 480, > + .link_freq_index = FREQ_INDEX_640, > + .fps = 120, > + .frame_len = 631, > + .llp = HI846_LINE_LENGTH, > + .reg_list_config = { > + .num_of_regs = ARRAY_SIZE(mode_640x480_config), > + .regs = mode_640x480_config, > + }, > + .reg_list_2lane = { > + .num_of_regs = ARRAY_SIZE(mode_640x480_mipi_2lane), > + .regs = mode_640x480_mipi_2lane, > + }, > + }, > + { > + .width = 1280, > + .height = 720, > + .link_freq_index = FREQ_INDEX_1280, > + .fps = 90, > + .frame_len = 842, > + .llp = HI846_LINE_LENGTH, > + .reg_list_config = { > + .num_of_regs = ARRAY_SIZE(mode_1280x720_config), > + .regs = mode_1280x720_config, > + }, > + .reg_list_2lane = { > + .num_of_regs = ARRAY_SIZE(mode_1280x720_mipi_2lane), > + .regs = mode_1280x720_mipi_2lane, > + }, > + .reg_list_4lane = { > + .num_of_regs = ARRAY_SIZE(mode_1280x720_mipi_4lane), > + .regs = mode_1280x720_mipi_4lane, > + }, > + }, > + { > + .width = 1632, > + .height = 1224, > + .link_freq_index = FREQ_INDEX_1280, > + .fps = 30, > + .frame_len = 2526, > + .llp = HI846_LINE_LENGTH, > + .reg_list_config = { > + .num_of_regs = ARRAY_SIZE(mode_1632x1224_config), > + .regs = mode_1632x1224_config, > + }, > + .reg_list_2lane = { > + .num_of_regs = ARRAY_SIZE(mode_1632x1224_mipi_2lane), > + .regs = mode_1632x1224_mipi_2lane, > + }, > + .reg_list_4lane = { > + .num_of_regs = ARRAY_SIZE(mode_1632x1224_mipi_4lane), > + .regs = mode_1632x1224_mipi_4lane, > + }, > + } > +}; > + > +struct hi846_gpio { > + int gpio; > + int level; > +}; > + > +struct hi846_datafmt { > + u32 code; > + enum v4l2_colorspace colorspace; > +}; > + > +struct hi846 { > + struct hi846_gpio rst_gpio; > + struct regulator *vdd1_regulator; > + struct regulator *vdd_regulator; > + struct clk *clock; > + struct hi846_datafmt *fmt; > + struct v4l2_subdev sd; > + struct media_pad pad; > + struct v4l2_ctrl_handler ctrl_handler; > + u8 nr_lanes; > + > + struct v4l2_ctrl *link_freq; > + struct v4l2_ctrl *pixel_rate; > + struct v4l2_ctrl *vblank; > + struct v4l2_ctrl *hblank; > + struct v4l2_ctrl *exposure; > + > + const struct hi846_mode *cur_mode; > + struct mutex mutex; > + bool streaming; > +}; > + > +static struct hi846_datafmt hi846_colour_fmts[] = { > + {HI846_MEDIA_BUS_FORMAT, V4L2_COLORSPACE_RAW}, > +}; > + > +static struct hi846_datafmt *hi846_find_datafmt(u32 code) > +{ > + int i; unsigned int > + > + for (i = 0; i < ARRAY_SIZE(hi846_colour_fmts); i++) > + if (hi846_colour_fmts[i].code == code) > + return hi846_colour_fmts + i; > + > + return NULL; > +} > + > +static inline u8 hi846_get_link_freq_index(struct hi846 *hi846) > +{ > + return hi846->cur_mode->link_freq_index; > +} > + > +static s64 hi846_get_link_freq(struct hi846 *hi846) > +{ > + u8 index = hi846_get_link_freq_index(hi846); > + > + return *(hi846_link_freqs + index); > +} > + > +static u64 hi846_calc_pixel_rate(struct hi846 *hi846) > +{ > + s64 link_freq = hi846_get_link_freq(hi846); > + u64 pixel_rate = link_freq * 2 * hi846->nr_lanes; > + > + do_div(pixel_rate, HI846_RGB_DEPTH); > + > + return pixel_rate; > +} > + > +static int hi846_read_reg(struct hi846 *hi846, u16 reg, u8 *val) > +{ > + struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd); > + struct i2c_msg msgs[2]; > + u8 addr_buf[2]; > + u8 data_buf[1] = {0}; > + int ret; > + > + put_unaligned_be16(reg, addr_buf); > + msgs[0].addr = client->addr; > + msgs[0].flags = 0; > + msgs[0].len = sizeof(addr_buf); > + msgs[0].buf = addr_buf; > + msgs[1].addr = client->addr; > + msgs[1].flags = I2C_M_RD; > + msgs[1].len = 1; > + msgs[1].buf = &data_buf[0]; > + > + ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs)); > + if (ret != ARRAY_SIZE(msgs)) { > + dev_err(&client->dev, "i2c read error: %d\n", ret); > + return -EIO; > + } > + > + *val = data_buf[0]; > + > + return 0; > +} > + > +static int hi846_write_reg_16(struct hi846 *hi846, u16 reg, u16 val) > +{ > + struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd); > + u8 buf[6]; > + > + put_unaligned_be16(reg, buf); > + put_unaligned_be32(val << 8 * 2, buf + 2); > + if (i2c_master_send(client, buf, 4) != 4) > + return -EIO; > + > + return 0; > +} > + > +static int hi846_write_reg_list(struct hi846 *hi846, > + const struct hi846_reg_list *r_list) > +{ > + struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd); > + unsigned int i; > + int ret; > + > + for (i = 0; i < r_list->num_of_regs; i++) { > + ret = hi846_write_reg_16(hi846, r_list->regs[i].address, > + r_list->regs[i].val); > + if (ret) { > + dev_err_ratelimited(&client->dev, > + "failed to write reg 0x%4.4x. error = %d", > + r_list->regs[i].address, ret); > + return ret; > + } > + } > + > + return 0; > +} > + > +static int hi846_write_reg(struct hi846 *hi846, u16 reg, u8 val) > +{ > + struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd); > + u8 buf[3] = { reg >> 8, reg & 0xff, val }; > + int ret; Please declare ret as last, and remove the empty line below. > + > + struct i2c_msg msg[] = { > + { .addr = client->addr, .flags = 0, > + .len = ARRAY_SIZE(buf), .buf = buf }, > + }; > + > + ret = i2c_transfer(client->adapter, msg, ARRAY_SIZE(msg)); > + if (ret != ARRAY_SIZE(msg)) { > + dev_err(&client->dev, "i2c write error\n"); > + return -EIO; > + } > + > + return 0; > +} > + > +static int hi846_update_digital_gain(struct hi846 *hi846, u16 d_gain) > +{ > + int ret; > + > + ret = hi846_write_reg_16(hi846, HI846_REG_MWB_GR_GAIN_H, d_gain); > + if (ret) > + return ret; > + > + ret = hi846_write_reg_16(hi846, HI846_REG_MWB_GB_GAIN_H, d_gain); > + if (ret) > + return ret; > + > + ret = hi846_write_reg_16(hi846, HI846_REG_MWB_R_GAIN_H, d_gain); > + if (ret) > + return ret; > + > + return hi846_write_reg_16(hi846, HI846_REG_MWB_B_GAIN_H, d_gain); > +} > + > +static int hi846_test_pattern(struct hi846 *hi846, u32 pattern) > +{ > + int ret; > + u8 val; > + > + if (pattern) { > + ret = hi846_read_reg(hi846, HI846_REG_ISP, &val); > + if (ret) > + return ret; > + > + ret = hi846_write_reg(hi846, HI846_REG_ISP, > + val | HI846_REG_ISP_TPG_EN); > + if (ret) > + return ret; > + } > + > + return hi846_write_reg(hi846, HI846_REG_TEST_PATTERN, pattern); > +} > + > +static int hi846_set_ctrl(struct v4l2_ctrl *ctrl) > +{ > + struct hi846 *hi846 = container_of(ctrl->handler, > + struct hi846, ctrl_handler); > + struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd); > + s64 exposure_max; > + int ret = 0; > + u32 shutter, frame_len; > + > + if (!pm_runtime_get_if_in_use(&client->dev)) > + goto out; You can return zero here and avoid the goto. This check also needs to take place after handling for vblank below. > + > + /* Propagate change of current control to all related controls */ > + if (ctrl->id == V4L2_CID_VBLANK) { > + /* Update max exposure while meeting expected vblanking */ > + exposure_max = hi846->cur_mode->height + ctrl->val - > + HI846_EXPOSURE_MAX_MARGIN; > + __v4l2_ctrl_modify_range(hi846->exposure, > + hi846->exposure->minimum, > + exposure_max, hi846->exposure->step, > + exposure_max); > + } > + > + switch (ctrl->id) { > + case V4L2_CID_ANALOGUE_GAIN: > + ret = hi846_write_reg(hi846, HI846_REG_ANALOG_GAIN, ctrl->val); > + break; > + > + case V4L2_CID_DIGITAL_GAIN: > + ret = hi846_update_digital_gain(hi846, ctrl->val); > + break; > + > + case V4L2_CID_EXPOSURE: > + shutter = ctrl->val; > + frame_len = hi846->cur_mode->frame_len; > + > + if (shutter > frame_len - 6) { /* margin */ > + frame_len = shutter + 6; > + if (frame_len > 0xffff) { /* max frame len */ > + frame_len = 0xffff; > + } > + } > + > + if (shutter < 6) > + shutter = 6; > + if (shutter > (0xffff - 6)) > + shutter = 0xffff - 6; You should handle this instead by changing the control range (min and max). > + > + ret = hi846_write_reg_16(hi846, HI846_REG_FLL, > + frame_len); > + ret = hi846_write_reg_16(hi846, HI846_REG_EXPOSURE, > + shutter); > + break; > + > + case V4L2_CID_VBLANK: > + /* Update FLL that meets expected vertical blanking */ > + ret = hi846_write_reg_16(hi846, HI846_REG_FLL, > + hi846->cur_mode->height + ctrl->val); > + break; > + case V4L2_CID_TEST_PATTERN: > + ret = hi846_test_pattern(hi846, ctrl->val); > + break; > + > + default: > + ret = -EINVAL; > + break; > + } > + > + pm_runtime_put(&client->dev); > +out: > + return ret; > +} > + > +static const struct v4l2_ctrl_ops hi846_ctrl_ops = { > + .s_ctrl = hi846_set_ctrl, > +}; > + > +static int hi846_init_controls(struct hi846 *hi846) > +{ > + struct v4l2_ctrl_handler *ctrl_hdlr; > + s64 exposure_max, h_blank; > + int ret; > + struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd); > + > + ctrl_hdlr = &hi846->ctrl_handler; > + ret = v4l2_ctrl_handler_init(ctrl_hdlr, 8); > + if (ret) > + return ret; > + > + ctrl_hdlr->lock = &hi846->mutex; > + > + hi846->link_freq = v4l2_ctrl_new_int_menu(ctrl_hdlr, &hi846_ctrl_ops, > + V4L2_CID_LINK_FREQ, > + ARRAY_SIZE(hi846_link_freqs) - 1, > + 0, hi846_link_freqs); Please align right of opening parenthesis. What you can also do: hi846->link_freq = v4l2_ctrl_new_int_menu(...); > + if (hi846->link_freq) > + hi846->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY; > + > + hi846->pixel_rate = v4l2_ctrl_new_std > + (ctrl_hdlr, &hi846_ctrl_ops, Please keep the opening parenthesis on the previous line. > + V4L2_CID_PIXEL_RATE, 0, > + hi846_calc_pixel_rate(hi846), > + 1, > + hi846_calc_pixel_rate(hi846)); > + hi846->vblank = v4l2_ctrl_new_std(ctrl_hdlr, &hi846_ctrl_ops, > + V4L2_CID_VBLANK, > + hi846->cur_mode->frame_len - > + hi846->cur_mode->height, > + HI846_FLL_MAX - > + hi846->cur_mode->height, 1, > + hi846->cur_mode->frame_len - > + hi846->cur_mode->height); > + > + h_blank = hi846->cur_mode->llp - hi846->cur_mode->width; > + > + hi846->hblank = v4l2_ctrl_new_std(ctrl_hdlr, &hi846_ctrl_ops, > + V4L2_CID_HBLANK, h_blank, h_blank, 1, > + h_blank); > + if (hi846->hblank) > + hi846->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY; > + > + v4l2_ctrl_new_std(ctrl_hdlr, &hi846_ctrl_ops, V4L2_CID_ANALOGUE_GAIN, > + HI846_ANAL_GAIN_MIN, HI846_ANAL_GAIN_MAX, > + HI846_ANAL_GAIN_STEP, HI846_ANAL_GAIN_MIN); > + v4l2_ctrl_new_std(ctrl_hdlr, &hi846_ctrl_ops, V4L2_CID_DIGITAL_GAIN, > + HI846_DGTL_GAIN_MIN, HI846_DGTL_GAIN_MAX, > + HI846_DGTL_GAIN_STEP, HI846_DGTL_GAIN_DEFAULT); > + exposure_max = hi846->cur_mode->frame_len - HI846_EXPOSURE_MAX_MARGIN; > + hi846->exposure = v4l2_ctrl_new_std(ctrl_hdlr, &hi846_ctrl_ops, > + V4L2_CID_EXPOSURE, > + HI846_EXPOSURE_MIN, exposure_max, > + HI846_EXPOSURE_STEP, > + exposure_max); > + v4l2_ctrl_new_std_menu_items(ctrl_hdlr, &hi846_ctrl_ops, > + V4L2_CID_TEST_PATTERN, > + ARRAY_SIZE(hi846_test_pattern_menu) - 1, > + 0, 0, hi846_test_pattern_menu); > + if (ctrl_hdlr->error) { > + dev_err(&client->dev, "v4l ctrl handler error: %d\n", > + ctrl_hdlr->error); > + return ctrl_hdlr->error; > + } > + > + hi846->sd.ctrl_handler = ctrl_hdlr; > + > + return 0; > +} > + > +static int hi846_set_video_mode(struct hi846 *hi846, int fps) > +{ > + struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd); > + int frame_length; > + int ret; > + int dummy_lines; > + > + dev_dbg(&client->dev, "%s: link freq: %lld\n", __func__, > + hi846_get_link_freq(hi846)); > + > + frame_length = hi846_get_link_freq(hi846) / fps / HI846_LINE_LENGTH; > + dummy_lines = (frame_length > hi846->cur_mode->frame_len) ? > + (frame_length - hi846->cur_mode->frame_len) : 0; > + > + frame_length = hi846->cur_mode->frame_len + dummy_lines; > + > + dev_dbg(&client->dev, "%s: frame length calculated: %d\n", __func__, > + frame_length); > + > + ret = hi846_write_reg_16(hi846, HI846_REG_FLL, frame_length & 0xFFFF); > + ret = hi846_write_reg_16(hi846, HI846_REG_LLP, HI846_LINE_LENGTH & 0xFFFF); > + > + return ret; > +} > + > +static int hi846_start_streaming(struct hi846 *hi846) > +{ > + struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd); > + int ret = 0; > + u8 val; > + > + if (hi846->nr_lanes == 2) > + ret = hi846_write_reg_list(hi846, &hi846_init_regs_list_2lane); > + else > + ret = hi846_write_reg_list(hi846, &hi846_init_regs_list_4lane); > + if (ret) { > + dev_err(&client->dev, "failed to set plls: %d\n", ret); > + return ret; > + } > + > + ret = hi846_write_reg_list(hi846, &hi846->cur_mode->reg_list_config); > + if (ret) { > + dev_err(&client->dev, "failed to set mode: %d\n", ret); > + return ret; > + } > + > + if (hi846->nr_lanes == 2) { > + if (!&hi846->cur_mode->reg_list_2lane) { > + dev_err(&client->dev, "2 lanes unsupported for this mode\n"); > + return -EINVAL; > + } > + ret = hi846_write_reg_list(hi846, &hi846->cur_mode->reg_list_2lane); > + } else { > + if (!&hi846->cur_mode->reg_list_4lane) { > + dev_err(&client->dev, "4 lanes unsupported for this mode\n"); > + return -EINVAL; > + } > + ret = hi846_write_reg_list(hi846, &hi846->cur_mode->reg_list_4lane); > + } > + if (ret) { > + dev_err(&client->dev, "failed to set mipi mode: %d\n", ret); > + return ret; > + } > + > + hi846_set_video_mode(hi846, hi846->cur_mode->fps); > + > + ret = __v4l2_ctrl_handler_setup(hi846->sd.ctrl_handler); > + if (ret) > + return ret; > + > + /* > + * Reading 0x0034 is purely done for debugging reasons: It is not > + * documented in the DS but only mentioned once: > + * "If 0x0034[2] bit is disabled , Visible pixel width and height is 0." > + * So even though that sounds like we won't see anything, we don't > + * know more about this, so in that case only inform the user but do > + * nothing more. > + */ > + ret = hi846_read_reg(hi846, 0x0034, &val); > + if (ret) > + return ret; > + if (!(val & BIT(2))) > + dev_info(&client->dev, "visible pixel width and height is 0\n"); > + > + ret = hi846_write_reg(hi846, HI846_REG_MODE_SELECT, > + HI846_MODE_STREAMING); > + if (ret) { > + dev_err(&client->dev, "failed to start stream"); > + return ret; > + } > + > + hi846->streaming = 1; > + > + dev_dbg(&client->dev, "%s: started streaming successfully\n", __func__); > + > + return ret; > +} > + > +static void hi846_stop_streaming(struct hi846 *hi846) > +{ > + struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd); > + > + if (hi846_write_reg(hi846, HI846_REG_MODE_SELECT, HI846_MODE_STANDBY)) > + dev_err(&client->dev, "failed to stop stream"); > + > + hi846->streaming = 0; > +} > + > +static int hi846_set_stream(struct v4l2_subdev *sd, int enable) > +{ > + struct hi846 *hi846 = to_hi846(sd); > + struct i2c_client *client = v4l2_get_subdevdata(sd); > + int ret = 0; > + > + if (hi846->streaming == enable) > + return 0; > + > + mutex_lock(&hi846->mutex); > + > + if (enable) { > + ret = pm_runtime_get_sync(&client->dev); > + if (ret < 0) { > + pm_runtime_put_noidle(&client->dev); > + goto out; > + } > + > + ret = hi846_start_streaming(hi846); > + if (ret) { > + enable = 0; > + hi846_stop_streaming(hi846); > + pm_runtime_put(&client->dev); > + } > + } else { > + hi846_stop_streaming(hi846); > + pm_runtime_put(&client->dev); > + } > + > +out: > + mutex_unlock(&hi846->mutex); > + > + return ret; > +} > + > +static int hi846_regulator_enable(struct hi846 *hi846) > +{ > + int ret = 0; > + > + ret = regulator_enable(hi846->vdd_regulator); > + if (ret) > + return ret; > + > + return regulator_enable(hi846->vdd1_regulator); > +} > + > +static void hi846_regulator_disable(struct hi846 *hi846) > +{ > + if (regulator_is_enabled(hi846->vdd1_regulator)) > + regulator_disable(hi846->vdd1_regulator); > + > + if (regulator_is_enabled(hi846->vdd_regulator)) > + regulator_disable(hi846->vdd_regulator); No need to check if a regulator is enabled before disabling it. > +} > + > +static int __maybe_unused hi846_suspend(struct device *dev) > +{ > + struct i2c_client *client = to_i2c_client(dev); > + struct v4l2_subdev *sd = i2c_get_clientdata(client); > + struct hi846 *hi846 = to_hi846(sd); > + > + if (hi846->streaming) > + hi846_stop_streaming(hi846); > + > + if (!IS_ERR(hi846->clock)) > + clk_disable_unprepare(hi846->clock); > + > + hi846_regulator_disable(hi846); Could you rely on runtime PM here? > + > + return 0; > +} > + > +static int __maybe_unused hi846_resume(struct device *dev) > +{ > + struct i2c_client *client = to_i2c_client(dev); > + struct v4l2_subdev *sd = i2c_get_clientdata(client); > + struct hi846 *hi846 = to_hi846(sd); > + int ret; > + > + ret = hi846_regulator_enable(hi846); > + if (ret) { > + dev_err(dev, "enable regulator failed: %d\n", ret); > + return ret; > + } > + > + ret = clk_prepare_enable(hi846->clock); > + if (ret < 0) { > + dev_err(dev, "enable clk failed: %d\n", ret); > + goto error_regulator; > + } > + > + msleep(100); And here. > + > + if (hi846->streaming) { > + ret = hi846_start_streaming(hi846); > + if (ret) { > + dev_err(dev, "%s: start streaming failed: %d\n", > + __func__, ret); > + goto error; > + } > + } > + > + return 0; > + > +error: > + clk_disable_unprepare(hi846->clock); > + > +error_regulator: > + hi846_regulator_disable(hi846); > + > + return ret; > +} > + > +static int hi846_set_format(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_format *format) > +{ > + struct hi846 *hi846 = to_hi846(sd); > + struct v4l2_mbus_framefmt *mf = &format->format; > + struct i2c_client *client = v4l2_get_subdevdata(sd); > + struct hi846_datafmt *fmt = hi846_find_datafmt(mf->code); > + u32 tgt_fps; > + s32 vblank_def, h_blank; > + > + if (!fmt) { > + mf->code = hi846_colour_fmts[0].code; > + mf->colorspace = hi846_colour_fmts[0].colorspace; > + fmt = &hi846_colour_fmts[0]; > + } > + > + if (format->which == V4L2_SUBDEV_FORMAT_TRY) { > + *v4l2_subdev_get_try_format(sd, cfg, format->pad) = *mf; > + return 0; > + } > + > + mutex_lock(&hi846->mutex); > + > + if (hi846->streaming) { > + mutex_unlock(&hi846->mutex); > + return -EBUSY; > + } > + > + hi846->fmt = fmt; > + > + hi846->cur_mode = v4l2_find_nearest_size(supported_modes, > + ARRAY_SIZE(supported_modes), width, Please align with the opening parenthesis. Could you check checkpatch.pl is relatively happy? Keep 80 chars per line in mind, too. > + height, mf->width, > + mf->height); > + dev_dbg(&client->dev, "%s: found mode: %dx%d\n", __func__, > + hi846->cur_mode->width, hi846->cur_mode->height); > + > + tgt_fps = hi846->cur_mode->fps; > + dev_dbg(&client->dev, "%s: target fps: %d\n", __func__, tgt_fps); > + > + mf->width = hi846->cur_mode->width; > + mf->height = hi846->cur_mode->height; > + mf->code = HI846_MEDIA_BUS_FORMAT; > + mf->field = V4L2_FIELD_NONE; > + > + __v4l2_ctrl_s_ctrl(hi846->link_freq, hi846_get_link_freq_index(hi846)); > + __v4l2_ctrl_s_ctrl_int64(hi846->pixel_rate, > + hi846_calc_pixel_rate(hi846)); > + > + /* Update limits and set FPS to default */ > + vblank_def = hi846->cur_mode->frame_len - hi846->cur_mode->height; > + __v4l2_ctrl_modify_range(hi846->vblank, > + hi846->cur_mode->frame_len - hi846->cur_mode->height, > + HI846_FLL_MAX - hi846->cur_mode->height, 1, > + vblank_def); > + __v4l2_ctrl_s_ctrl(hi846->vblank, vblank_def); > + > + h_blank = hi846->cur_mode->llp - hi846->cur_mode->width; > + > + __v4l2_ctrl_modify_range(hi846->hblank, h_blank, h_blank, 1, > + h_blank); > + > + dev_dbg(&client->dev, "Set fmt w=%d h=%d code=0x%x colorspace=0x%x\n", > + mf->width, mf->height, > + fmt->code, fmt->colorspace); > + > + mutex_unlock(&hi846->mutex); > + > + return 0; > +} > + > +static int hi846_get_format(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_format *format) > +{ > + struct hi846 *hi846 = to_hi846(sd); > + struct v4l2_mbus_framefmt *mf = &format->format; > + struct i2c_client *client = v4l2_get_subdevdata(sd); > + > + if (format->pad) > + return -EINVAL; The caller has checked for this already, so you can remove it here. Same for the other similar callbacks. > + > + if (format->which == V4L2_SUBDEV_FORMAT_TRY) { > + format->format = *v4l2_subdev_get_try_format(&hi846->sd, > + cfg, > + format->pad); > + return 0; > + } > + > + mutex_lock(&hi846->mutex); > + mf->code = HI846_MEDIA_BUS_FORMAT; > + mf->colorspace = V4L2_COLORSPACE_RAW; > + mf->field = V4L2_FIELD_NONE; > + mf->width = hi846->cur_mode->width; > + mf->height = hi846->cur_mode->height; > + mutex_unlock(&hi846->mutex); > + dev_dbg(&client->dev, > + "Get format w=%d h=%d code=0x%x colorspace=0x%x\n", > + mf->width, mf->height, mf->code, mf->colorspace); > + > + return 0; > +} > + > +static int hi846_enum_mbus_code(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_mbus_code_enum *code) > +{ > + if (code->pad || code->index > 0) > + return -EINVAL; > + > + code->code = HI846_MEDIA_BUS_FORMAT; > + > + return 0; > +} > + > +static int hi846_enum_frame_size(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_frame_size_enum *fse) > +{ > + struct i2c_client *client = v4l2_get_subdevdata(sd); > + > + if (fse->pad || fse->index >= ARRAY_SIZE(supported_modes)) > + return -EINVAL; > + > + if (fse->code != HI846_MEDIA_BUS_FORMAT) { > + dev_err(&client->dev, "frame size enum not matching\n"); > + return -EINVAL; > + } > + > + fse->min_width = supported_modes[fse->index].width; > + fse->max_width = supported_modes[fse->index].width; > + fse->min_height = supported_modes[fse->index].height; > + fse->max_height = supported_modes[fse->index].height; > + > + dev_dbg(&client->dev, "%s: max width: %d max height: %d\n", __func__, > + fse->max_width, fse->max_height); > + > + return 0; > +} > + > +static int hi846_s_power(struct v4l2_subdev *sd, int on) There's no need for implementing s_power anymore in sensor drivers using runtime PM. Please remove it. > +{ > + struct hi846 *hi846 = to_hi846(sd); > + struct i2c_client *client = v4l2_get_subdevdata(sd); > + struct device *dev = &client->dev; > + int ret = 0; > + > + mutex_lock(&hi846->mutex); > + if (on) { > + ret = hi846_resume(dev); > + if (ret) > + goto out; > + } else { > + ret = hi846_suspend(dev); > + if (ret) > + goto out; > + } > +out: > + mutex_unlock(&hi846->mutex); > + return ret; > +} > + > +static int hi846_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh) > +{ > + struct hi846 *hi846 = to_hi846(sd); > + struct v4l2_mbus_framefmt *mf; > + > + mf = v4l2_subdev_get_try_format(sd, fh->pad, 0); > + > + mutex_lock(&hi846->mutex); > + mf->code = HI846_MEDIA_BUS_FORMAT; > + mf->colorspace = V4L2_COLORSPACE_RAW; > + mf->field = V4L2_FIELD_NONE; > + mf->width = hi846->cur_mode->width; > + mf->height = hi846->cur_mode->height; > + mutex_unlock(&hi846->mutex); > + > + return 0; > +} > + > +static const struct v4l2_subdev_video_ops hi846_video_ops = { > + .s_stream = hi846_set_stream, > +}; > + > +static const struct v4l2_subdev_pad_ops hi846_pad_ops = { > + .enum_frame_size = hi846_enum_frame_size, > + .enum_mbus_code = hi846_enum_mbus_code, > + .set_fmt = hi846_set_format, > + .get_fmt = hi846_get_format, > +}; > + > +static struct v4l2_subdev_core_ops hi846_core_ops = { > + .s_power = hi846_s_power, > + .log_status = v4l2_ctrl_subdev_log_status, > +}; > + > +static const struct v4l2_subdev_ops hi846_subdev_ops = { > + .core = &hi846_core_ops, > + .video = &hi846_video_ops, > + .pad = &hi846_pad_ops, > +}; > + > +static const struct media_entity_operations hi846_subdev_entity_ops = { > + .link_validate = v4l2_subdev_link_validate, > +}; > + > +static const struct v4l2_subdev_internal_ops hi846_internal_ops = { > + .open = hi846_open, > +}; > + > +static void hi846_rst_gpio_assert(struct hi846 *hi846, bool on) > +{ > + struct hi846_gpio *gpio = &hi846->rst_gpio; > + > + if (gpio == NULL) > + return; > + > + if (on) > + gpio_set_value(gpio->gpio, gpio->level); > + else > + gpio_set_value(gpio->gpio, !gpio->level); > +} > + > +static int hi846_parse_gpio(struct hi846_gpio *gpio, struct device *dev) > +{ > + struct device_node *node = dev->of_node; > + enum of_gpio_flags flags; > + int ret; > + > + ret = of_get_named_gpio_flags(node, "rst-gpios", 0, &flags); > + if (ret < 0) { > + dev_err(dev, "no rst-gpios provided: %d\n", ret); > + return ret; > + } > + gpio->gpio = ret; > + gpio->level = !(flags & OF_GPIO_ACTIVE_LOW); Doesn't the GPIO framework handle this already? You also should use the gpiod API instead. > + > + return 0; > +} > + > +static int hi846_identify_module(struct hi846 *hi846) > +{ > + struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd); > + int ret; > + u8 hi, lo; > + > + ret = hi846_read_reg(hi846, HI846_REG_CHIP_ID_L, &lo); > + if (ret) > + return ret; > + > + if (lo != HI846_CHIP_ID_L) { > + dev_err(&client->dev, "wrong chip id low byte: %x", lo); > + return -ENXIO; > + } > + > + ret = hi846_read_reg(hi846, HI846_REG_CHIP_ID_H, &hi); > + if (ret) > + return ret; > + > + if (hi != HI846_CHIP_ID_H) { > + dev_err(&client->dev, "wrong chip id high byte: %x", hi); > + return -ENXIO; > + } > + > + dev_info(&client->dev, "chip id %02X %02X / %d mipi lanes\n", hi, lo, > + hi846->nr_lanes); > + > + return 0; > +} > + > +static int hi846_check_hwcfg(struct device *dev, u8 *lanes) > +{ > + struct fwnode_handle *ep; > + struct fwnode_handle *fwnode = dev_fwnode(dev); > + struct v4l2_fwnode_endpoint bus_cfg = { > + .bus_type = V4L2_MBUS_CSI2_DPHY > + }; > + int ret = 0; Assigning ret here is redundant. > + > + if (!fwnode) > + return -ENXIO; > + > + ep = fwnode_graph_get_next_endpoint(fwnode, NULL); > + if (!ep) > + return -ENXIO; > + > + ret = v4l2_fwnode_endpoint_alloc_parse(ep, &bus_cfg); > + fwnode_handle_put(ep); > + if (ret) > + return ret; > + > + if (bus_cfg.bus.mipi_csi2.num_data_lanes != 2 && > + bus_cfg.bus.mipi_csi2.num_data_lanes != 4) { > + dev_err(dev, "number of CSI2 data lanes %d is not supported", > + bus_cfg.bus.mipi_csi2.num_data_lanes); > + ret = -EINVAL; > + goto check_hwcfg_error; > + } > + > + *lanes = bus_cfg.bus.mipi_csi2.num_data_lanes; > + > +check_hwcfg_error: > + v4l2_fwnode_endpoint_free(&bus_cfg); > + > + return ret; > +} > + > +static int hi846_remove(struct i2c_client *client) > +{ > + struct v4l2_subdev *sd = i2c_get_clientdata(client); > + struct hi846 *hi846 = to_hi846(sd); > + > + v4l2_async_unregister_subdev(sd); > + media_entity_cleanup(&sd->entity); > + v4l2_ctrl_handler_free(sd->ctrl_handler); > + > + pm_runtime_disable(&client->dev); > + if (!pm_runtime_status_suspended(&client->dev)) > + hi846_suspend(&client->dev); > + pm_runtime_set_suspended(&client->dev); > + > + mutex_destroy(&hi846->mutex); > + > + return 0; > +} > + > +static int hi846_probe(struct i2c_client *client) > +{ > + struct hi846 *hi846; > + int ret; > + u8 lanes; > + > + ret = hi846_check_hwcfg(&client->dev, &lanes); > + if (ret) { > + dev_err(&client->dev, "failed to check HW configuration: %d", > + ret); > + return ret; > + } > + > + hi846 = devm_kzalloc(&client->dev, sizeof(*hi846), GFP_KERNEL); > + if (!hi846) > + return -ENOMEM; > + > + hi846->nr_lanes = lanes; > + > + v4l2_i2c_subdev_init(&hi846->sd, client, &hi846_subdev_ops); > + > + ret = hi846_parse_gpio(&hi846->rst_gpio, &client->dev); > + if (ret < 0) { > + dev_err(&client->dev, "parse gpio failed: %d\n", ret); > + return ret; > + } > + > + hi846->vdd_regulator = devm_regulator_get(&client->dev, "vdd"); > + if (IS_ERR(hi846->vdd_regulator)) > + dev_warn(&client->dev, "cannot get voltage regulator\n"); > + > + hi846->vdd1_regulator = devm_regulator_get(&client->dev, "vdd1"); > + if (IS_ERR(hi846->vdd1_regulator)) > + dev_warn(&client->dev, "cannot get voltage regulator\n"); I'd return an error from probe here. > + > + ret = hi846_regulator_enable(hi846); > + if (ret) { > + dev_err(&client->dev, "regulator enable failed: %d\n", ret); > + return ret; > + } > + > + hi846->clock = devm_clk_get(hi846->sd.dev, "mclk"); > + if (IS_ERR(hi846->clock)) { > + dev_err(&client->dev, "get clk failed\n"); > + ret = -EPROBE_DEFER; > + goto probe_error_regulator; > + } > + > + ret = clk_prepare_enable(hi846->clock); > + if (ret < 0) > + goto probe_error_regulator; > + > + msleep(100); > + > + hi846_rst_gpio_assert(hi846, true); > + Almost all sensors need a delay here (but not often before lifting xshutdown). Have you checked this sequence is as the spec says (just wondering)? > + ret = hi846_identify_module(hi846); > + if (ret) { > + dev_err(&client->dev, "failed to find sensor: %d", ret); > + goto probe_error_regulator; > + } > + > + mutex_init(&hi846->mutex); > + > + hi846->cur_mode = &supported_modes[0]; > + ret = hi846_init_controls(hi846); > + if (ret) { > + dev_err(&client->dev, "failed to init controls: %d", ret); > + goto probe_error_v4l2_ctrl_handler_free; > + } > + > + hi846->sd.internal_ops = &hi846_internal_ops; > + hi846->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; > + hi846->sd.entity.ops = &hi846_subdev_entity_ops; > + hi846->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR; > + hi846->pad.flags = MEDIA_PAD_FL_SOURCE; > + ret = media_entity_pads_init(&hi846->sd.entity, 1, &hi846->pad); > + if (ret) { > + dev_err(&client->dev, "failed to init entity pads: %d", ret); > + goto probe_error_v4l2_ctrl_handler_free; > + } > + > + ret = v4l2_async_register_subdev_sensor(&hi846->sd); > + if (ret < 0) { > + dev_err(&client->dev, "failed to register V4L2 subdev: %d", > + ret); > + goto probe_error_media_entity_cleanup; > + } > + > + pm_runtime_set_active(&client->dev); > + pm_runtime_enable(&client->dev); > + pm_runtime_idle(&client->dev); > + > + return 0; > + > +probe_error_media_entity_cleanup: > + media_entity_cleanup(&hi846->sd.entity); > + > +probe_error_v4l2_ctrl_handler_free: > + v4l2_ctrl_handler_free(hi846->sd.ctrl_handler); > + mutex_destroy(&hi846->mutex); > + > +probe_error_regulator: > + hi846_regulator_disable(hi846); > + > + return ret; > +} > + > +static UNIVERSAL_DEV_PM_OPS(hi846_pm_ops, hi846_suspend, hi846_resume, NULL); > + > +static const struct of_device_id hi846_of_match[] = { > + { .compatible = "hynix,hi846", }, > + {}, > +}; > +MODULE_DEVICE_TABLE(of, hi846_of_match); > + > +static struct i2c_driver hi846_i2c_driver = { > + .driver = { > + .name = "hi846", > + .pm = &hi846_pm_ops, > + .of_match_table = of_match_ptr(hi846_of_match), > + }, > + .probe_new = hi846_probe, > + .remove = hi846_remove, > +}; > + > +module_i2c_driver(hi846_i2c_driver); > + > +MODULE_AUTHOR("Angus Ainslie <angus@akkea.ca>"); > +MODULE_AUTHOR("Martin Kepplinger <martin.kepplinger@puri.sm>"); > +MODULE_DESCRIPTION("Hynix HI846 sensor driver"); > +MODULE_LICENSE("GPL v2"); -- Kind regards, Sakari Ailus ^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v2 4/5] arm64: defconfig: enable VIDEO_HI846 2021-05-28 8:13 [PATCH v2 0/5] Add support for the Hynix Hi-846 camera Martin Kepplinger ` (2 preceding siblings ...) 2021-05-28 8:13 ` [PATCH v2 3/5] media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera Martin Kepplinger @ 2021-05-28 8:13 ` Martin Kepplinger 2021-05-28 8:13 ` [PATCH v2 5/5] Documentation: i2c-cardlist: add the Hynix hi846 sensor Martin Kepplinger 2021-05-30 21:23 ` [PATCH v2 0/5] Add support for the Hynix Hi-846 camera Pavel Machek 5 siblings, 0 replies; 18+ messages in thread From: Martin Kepplinger @ 2021-05-28 8:13 UTC (permalink / raw) To: laurent.pinchart, mchehab Cc: devicetree, kernel, krzysztof.kozlowski, linux-kernel, linux-media, paul.kocialkowski, robh, shawnx.tu, Martin Kepplinger build the driver for the Hi-846 camera by default on arm64, where it's going to be used on at least the imx8mq-librem5 board. Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> --- arch/arm64/configs/defconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig index 08c6f769df9a..3a5238c1f3b3 100644 --- a/arch/arm64/configs/defconfig +++ b/arch/arm64/configs/defconfig @@ -664,6 +664,7 @@ CONFIG_VIDEO_RENESAS_FCP=m CONFIG_VIDEO_RENESAS_VSP1=m CONFIG_SDR_PLATFORM_DRIVERS=y CONFIG_VIDEO_RCAR_DRIF=m +CONFIG_VIDEO_HI846=m CONFIG_VIDEO_IMX219=m CONFIG_VIDEO_OV5645=m CONFIG_VIDEO_QCOM_CAMSS=m -- 2.30.2 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v2 5/5] Documentation: i2c-cardlist: add the Hynix hi846 sensor 2021-05-28 8:13 [PATCH v2 0/5] Add support for the Hynix Hi-846 camera Martin Kepplinger ` (3 preceding siblings ...) 2021-05-28 8:13 ` [PATCH v2 4/5] arm64: defconfig: enable VIDEO_HI846 Martin Kepplinger @ 2021-05-28 8:13 ` Martin Kepplinger 2021-05-30 21:23 ` [PATCH v2 0/5] Add support for the Hynix Hi-846 camera Pavel Machek 5 siblings, 0 replies; 18+ messages in thread From: Martin Kepplinger @ 2021-05-28 8:13 UTC (permalink / raw) To: laurent.pinchart, mchehab Cc: devicetree, kernel, krzysztof.kozlowski, linux-kernel, linux-media, paul.kocialkowski, robh, shawnx.tu, Martin Kepplinger Add the SK Hynix Hi-846 8M Pixel CMOS image sensor to the i2c-cardlist. Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> --- Documentation/admin-guide/media/i2c-cardlist.rst | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/admin-guide/media/i2c-cardlist.rst b/Documentation/admin-guide/media/i2c-cardlist.rst index e60d459d18a9..185e07a3da43 100644 --- a/Documentation/admin-guide/media/i2c-cardlist.rst +++ b/Documentation/admin-guide/media/i2c-cardlist.rst @@ -60,6 +60,7 @@ Driver Name ============ ========================================================== et8ek8 ET8EK8 camera sensor hi556 Hynix Hi-556 sensor +hi846 Hynix Hi-846 sensor imx214 Sony IMX214 sensor imx219 Sony IMX219 sensor imx258 Sony IMX258 sensor -- 2.30.2 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* Re: [PATCH v2 0/5] Add support for the Hynix Hi-846 camera 2021-05-28 8:13 [PATCH v2 0/5] Add support for the Hynix Hi-846 camera Martin Kepplinger ` (4 preceding siblings ...) 2021-05-28 8:13 ` [PATCH v2 5/5] Documentation: i2c-cardlist: add the Hynix hi846 sensor Martin Kepplinger @ 2021-05-30 21:23 ` Pavel Machek 5 siblings, 0 replies; 18+ messages in thread From: Pavel Machek @ 2021-05-30 21:23 UTC (permalink / raw) To: Martin Kepplinger Cc: laurent.pinchart, mchehab, devicetree, kernel, krzysztof.kozlowski, linux-kernel, linux-media, paul.kocialkowski, robh, shawnx.tu [-- Attachment #1: Type: text/plain, Size: 467 bytes --] Hi! > This patchset add support for the SK Hynix Hi-846 CMOS images sensor. > It includes documentation, dt-bindings and the driver. > > patch 4 and 5 are basically optional: if i2c-cardlist is deprecated, > ignore it and act on it appropriately, and the defconfig would just > be convenience for now. Can I get you to cc phone-devel@vger.kernel.org with phone-related patches? Thank you, Pavel -- http://www.livejournal.com/~pavelmachek [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 195 bytes --] ^ permalink raw reply [flat|nested] 18+ messages in thread
end of thread, other threads:[~2021-06-02 14:37 UTC | newest] Thread overview: 18+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2021-05-28 8:13 [PATCH v2 0/5] Add support for the Hynix Hi-846 camera Martin Kepplinger 2021-05-28 8:13 ` [PATCH v2 1/5] dt-bindings: vendor-prefixes: Add SK Hynix Inc Martin Kepplinger 2021-05-28 8:13 ` [PATCH v2 2/5] dt-bindings: media: document SK Hynix Hi-846 MIPI CSI-2 8M pixel sensor Martin Kepplinger 2021-05-28 8:35 ` Laurent Pinchart 2021-06-02 13:52 ` Sakari Ailus 2021-06-02 13:51 ` Sakari Ailus 2021-06-02 14:05 ` Laurent Pinchart 2021-06-02 14:12 ` Martin Kepplinger 2021-06-02 14:37 ` Sakari Ailus 2021-05-28 8:13 ` [PATCH v2 3/5] media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera Martin Kepplinger 2021-05-28 18:20 ` kernel test robot 2021-05-28 18:20 ` kernel test robot 2021-05-28 19:08 ` kernel test robot 2021-05-28 19:08 ` kernel test robot 2021-06-02 14:36 ` Sakari Ailus 2021-05-28 8:13 ` [PATCH v2 4/5] arm64: defconfig: enable VIDEO_HI846 Martin Kepplinger 2021-05-28 8:13 ` [PATCH v2 5/5] Documentation: i2c-cardlist: add the Hynix hi846 sensor Martin Kepplinger 2021-05-30 21:23 ` [PATCH v2 0/5] Add support for the Hynix Hi-846 camera Pavel Machek
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.