* [PATCH V2 2/2] arm64: dts: ti: Add support for J721E EAIK
@ 2021-06-07 9:33 ` Sinthu Raja
0 siblings, 0 replies; 22+ messages in thread
From: Sinthu Raja @ 2021-06-07 9:33 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: Device Tree Mailing List, Linux ARM Mailing List, Lokesh Vutla,
Amarnath MB, Sinthu Raja
From: Sinthu Raja <sinthu.raja@ti.com>
J721E EdgeAI Kit (EAIK) is a low cost, small form factor board designed
for TI’s J721E SoC. TI’s J721E SoC comprises of dual core A72, high
performance vision accelerators, video codec accelerators, latest C71x
and C66x DSP, high bandwidth real-time IPs for capture and display, GPU,
dedicated safety island and security accelerators. The SoC is power
optimized to provide best in class performance for perception, sensor
fusion, localization, path planning tasks in robotics, industrial and
automotive applications.
J721E EAIK supports the following interfaces:
* 4 GB LPDDR4 RAM
* x1 Gigabit Ethernet interface
* x1 USB 3.0 Type-C port
* x3 USB 3.0 Type-A ports
* x1 UHS-1 capable µSD card slot
* x1 PCIe M.2 E Key with x1 USB2.0, x1 MCASP, x1 MMC, x1 UART
* x1 PCIe M.2 M Key
* 512 Mbit OSPI flash
* x4 UART through UART-USB bridge
* x4 CAN-FD interface
* x1 DP interface
* x1 HDMI interface
* x2 CSI2 Camera interface (RPi and TI Camera connector)
* 40-pin Raspberry Pi compatible GPIO header
* Compact TI 20-Pin connector for JTAG debug
* Interface for remote automation. Includes:
* power measurement and reset control
* boot mode change
Add basic support for J721E-EAIK.
Signed-off-by: Amarnath MB <amarnath.mb@ti.com>
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
---
arch/arm64/boot/dts/ti/Makefile | 2 +
arch/arm64/boot/dts/ti/k3-j721e-eaik.dts | 342 +++++++++++++++++++++++
2 files changed, 344 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index d56c742f5a10..00eb2077616e 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -12,6 +12,8 @@ dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-j721e-eaik.dtb
+
dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-eaik.dts b/arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
new file mode 100644
index 000000000000..decb16274333
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
@@ -0,0 +1,342 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+
+#include "k3-j721e.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/net/ti-dp83867.h>
+
+/ {
+ compatible = "ti,j721e-eaik", "ti,j721e";
+ model = "Texas Instruments J721E EAIK";
+
+ chosen {
+ stdout-path = "serial2:115200n8";
+ bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ /* 4G RAM */
+ reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
+ <0x00000008 0x80000000 0x00000000 0x80000000>;
+ };
+
+ reserved_memory: reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ secure_ddr: optee@9e800000 {
+ reg = <0x00 0x9e800000 0x00 0x01800000>;
+ alignment = <0x1000>;
+ no-map;
+ };
+ };
+
+ vusb_main: fixedregulator-vusb-main5v0 {
+ /* USB MAIN INPUT 5V DC */
+ compatible = "regulator-fixed";
+ regulator-name = "vusb-main5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vsys_3v3: fixedregulator-vsys3v3 {
+ /* Output of LM5141 */
+ compatible = "regulator-fixed";
+ regulator-name = "vsys_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vusb_main>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_mmc1: fixedregulator-sd {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_mmc1_en_pins_default>;
+ regulator-name = "vdd_mmc1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ vin-supply = <&vsys_3v3>;
+ gpio = <&wkup_gpio0 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ vdd_sd_dv_alt: gpio-regulator-tps659411 {
+ compatible = "regulator-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_sd_dv_alt_pins_default>;
+ regulator-name = "tps659411";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ vin-supply = <&vsys_3v3>;
+ gpios = <&wkup_gpio0 9 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x0>,
+ <3300000 0x1>;
+ };
+};
+
+&main_pmx0 {
+ main_mmc1_pins_default: main-mmc1-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x254, PIN_INPUT, 0) /* (R29) MMC1_CMD */
+ J721E_IOPAD(0x250, PIN_INPUT, 0) /* (P25) MMC1_CLK */
+ J721E_IOPAD(0x2ac, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */
+ J721E_IOPAD(0x24c, PIN_INPUT, 0) /* (R24) MMC1_DAT0 */
+ J721E_IOPAD(0x248, PIN_INPUT, 0) /* (P24) MMC1_DAT1 */
+ J721E_IOPAD(0x244, PIN_INPUT, 0) /* (R25) MMC1_DAT2 */
+ J721E_IOPAD(0x240, PIN_INPUT, 0) /* (R26) MMC1_DAT3 */
+ J721E_IOPAD(0x258, PIN_INPUT, 0) /* (P23) MMC1_SDCD */
+ >;
+ };
+
+ main_uart0_pins_default: main-uart0-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x1f0, PIN_INPUT, 0) /* (AC2) UART0_CTSn */
+ J721E_IOPAD(0x1f4, PIN_OUTPUT, 0) /* (AB1) UART0_RTSn */
+ J721E_IOPAD(0x1e8, PIN_INPUT, 0) /* (AB2) UART0_RXD */
+ J721E_IOPAD(0x1ec, PIN_OUTPUT, 0) /* (AB3) UART0_TXD */
+ >;
+ };
+
+ main_i2c0_pins_default: main-i2c0-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x220, PIN_INPUT_PULLUP, 0) /* (AC5) I2C0_SCL */
+ J721E_IOPAD(0x224, PIN_INPUT_PULLUP, 0) /* (AA5) I2C0_SDA */
+ >;
+ };
+
+ main_i2c1_pins_default: main-i2c1-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x228, PIN_INPUT_PULLUP, 0) /* (Y6) I2C1_SCL */
+ J721E_IOPAD(0x22c, PIN_INPUT_PULLUP, 0) /* (AA6) I2C1_SDA */
+ >;
+ };
+
+ main_i2c3_pins_default: main-i2c3-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x270, PIN_INPUT_PULLUP, 4) /* (T26) MMC2_CLK.I2C3_SCL */
+ J721E_IOPAD(0x274, PIN_INPUT_PULLUP, 4) /* (T25) MMC2_CMD.I2C3_SDA */
+ >;
+ };
+};
+
+&wkup_pmx0 {
+ mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x0, PIN_OUTPUT, 0) /* (E20) MCU_OSPI0_CLK */
+ J721E_WKUP_IOPAD(0x2c, PIN_OUTPUT, 0) /* (F19) MCU_OSPI0_CSn0 */
+ J721E_WKUP_IOPAD(0xc, PIN_INPUT, 0) /* (D20) MCU_OSPI0_D0 */
+ J721E_WKUP_IOPAD(0x10, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D1 */
+ J721E_WKUP_IOPAD(0x14, PIN_INPUT, 0) /* (G20) MCU_OSPI0_D2 */
+ J721E_WKUP_IOPAD(0x18, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D3 */
+ J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 0) /* (F21) MCU_OSPI0_D4 */
+ J721E_WKUP_IOPAD(0x20, PIN_INPUT, 0) /* (E21) MCU_OSPI0_D5 */
+ J721E_WKUP_IOPAD(0x24, PIN_INPUT, 0) /* (B22) MCU_OSPI0_D6 */
+ J721E_WKUP_IOPAD(0x28, PIN_INPUT, 0) /* (G21) MCU_OSPI0_D7 */
+ J721E_WKUP_IOPAD(0x8, PIN_INPUT, 0) /* (D21) MCU_OSPI0_DQS */
+ >;
+ };
+
+ vdd_mmc1_en_pins_default: vdd-mmc1-en-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0xd0, PIN_OUTPUT, 7) /* (G27) WKUP_GPIO0_8 */
+ >;
+ };
+
+ vdd_sd_dv_alt_pins_default: vdd-sd-dv-alt-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0xd4, PIN_OUTPUT, 7) /* (G26) WKUP_GPIO0_9 */
+ >;
+ };
+
+ wkup_i2c0_pins_default: wkup-i2c0-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
+ J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
+ >;
+ };
+};
+
+&wkup_uart0 {
+ /* Wakeup UART is used by System firmware */
+ status = "reserved";
+};
+
+&main_uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_uart0_pins_default>;
+ /* Shared with ATF on this platform */
+ power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
+};
+
+&main_uart2 {
+ /* Brought out on RPi header */
+ status = "disabled";
+};
+
+&main_uart3 {
+ /* UART not brought out */
+ status = "disabled";
+};
+
+&main_uart5 {
+ /* UART not brought out */
+ status = "disabled";
+};
+
+&main_uart6 {
+ /* UART not brought out */
+ status = "disabled";
+};
+
+&main_uart7 {
+ /* UART not brought out */
+ status = "disabled";
+};
+
+&main_uart8 {
+ /* UART not brought out */
+ status = "disabled";
+};
+
+&main_uart9 {
+ /* Brought out on M.2 E Key */
+ status = "disabled";
+};
+
+&main_sdhci0 {
+ /* Unused */
+ status = "disabled";
+};
+
+&main_sdhci1 {
+ /* SD Card */
+ vmmc-supply = <&vdd_mmc1>;
+ vqmmc-supply = <&vdd_sd_dv_alt>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mmc1_pins_default>;
+ ti,driver-strength-ohm = <50>;
+ disable-wp;
+};
+
+&main_sdhci2 {
+ /* Unused */
+ status = "disabled";
+};
+
+&ospi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+
+ flash@0{
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-tx-bus-width = <8>;
+ spi-rx-bus-width = <8>;
+ spi-max-frequency = <25000000>;
+ cdns,tshsl-ns = <60>;
+ cdns,tsd2d-ns = <60>;
+ cdns,tchsh-ns = <60>;
+ cdns,tslch-ns = <60>;
+ cdns,read-delay = <4>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition@3fc0000 {
+ label = "ospi.phypattern";
+ reg = <0x3fc0000 0x40000>;
+ u-boot,dm-spl;
+ };
+ };
+};
+
+&ospi1 {
+ /* Unused */
+ status = "disabled";
+};
+
+&main_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c0_pins_default>;
+ clock-frequency = <400000>;
+
+ i2c-switch@71 {
+ compatible = "nxp,pca9543";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x71>;
+
+ /* PCIe1 M.2 M Key I2C */
+ pcie1_m2_i2c: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ /* PCIe0 M.2 E Key I2C */
+ pcie0_m2_i2c: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ };
+};
+
+&main_i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c1_pins_default>;
+ clock-frequency = <400000>;
+};
+
+&main_i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c3_pins_default>;
+ clock-frequency = <400000>;
+
+ i2c-switch@70 {
+ compatible = "nxp,pca9543";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x70>;
+
+ /* CAM0 I2C */
+ ti_cam0_i2c: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ /* CAM1 I2C */
+ rpi_cam0_i2c: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ };
+};
+
+&main_i2c4 {
+ /* Unused */
+ status = "disabled";
+};
+
+&main_i2c5 {
+ /* Brought out on RPi Header */
+ status = "disabled";
+};
+
+&main_i2c6 {
+ /* Unused */
+ status = "disabled";
+};
--
2.31.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 22+ messages in thread
* Re: [PATCH V2 2/2] arm64: dts: ti: Add support for J721E EAIK
2021-06-07 9:33 ` Sinthu Raja
@ 2021-06-07 13:35 ` Nishanth Menon
-1 siblings, 0 replies; 22+ messages in thread
From: Nishanth Menon @ 2021-06-07 13:35 UTC (permalink / raw)
To: Sinthu Raja
Cc: Tero Kristo, Rob Herring, Device Tree Mailing List,
Linux ARM Mailing List, Lokesh Vutla, Amarnath MB, Sinthu Raja
On 15:03-20210607, Sinthu Raja wrote:
> From: Sinthu Raja <sinthu.raja@ti.com>
>
> J721E EdgeAI Kit (EAIK) is a low cost, small form factor board designed
> for TI’s J721E SoC. TI’s J721E SoC comprises of dual core A72, high
> performance vision accelerators, video codec accelerators, latest C71x
> and C66x DSP, high bandwidth real-time IPs for capture and display, GPU,
> dedicated safety island and security accelerators. The SoC is power
> optimized to provide best in class performance for perception, sensor
> fusion, localization, path planning tasks in robotics, industrial and
> automotive applications.
>
> J721E EAIK supports the following interfaces:
> * 4 GB LPDDR4 RAM
> * x1 Gigabit Ethernet interface
> * x1 USB 3.0 Type-C port
> * x3 USB 3.0 Type-A ports
> * x1 UHS-1 capable µSD card slot
> * x1 PCIe M.2 E Key with x1 USB2.0, x1 MCASP, x1 MMC, x1 UART
> * x1 PCIe M.2 M Key
> * 512 Mbit OSPI flash
> * x4 UART through UART-USB bridge
> * x4 CAN-FD interface
> * x1 DP interface
> * x1 HDMI interface
> * x2 CSI2 Camera interface (RPi and TI Camera connector)
> * 40-pin Raspberry Pi compatible GPIO header
> * Compact TI 20-Pin connector for JTAG debug
> * Interface for remote automation. Includes:
> * power measurement and reset control
> * boot mode change
please reduce the description above, also add a url for the board.
>
> Add basic support for J721E-EAIK.
>
> Signed-off-by: Amarnath MB <amarnath.mb@ti.com>
> Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
> ---
> arch/arm64/boot/dts/ti/Makefile | 2 +
> arch/arm64/boot/dts/ti/k3-j721e-eaik.dts | 342 +++++++++++++++++++++++
> 2 files changed, 344 insertions(+)
> create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
>
> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> index d56c742f5a10..00eb2077616e 100644
> --- a/arch/arm64/boot/dts/ti/Makefile
> +++ b/arch/arm64/boot/dts/ti/Makefile
> @@ -12,6 +12,8 @@ dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb
>
> dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
>
> +dtb-$(CONFIG_ARCH_K3) += k3-j721e-eaik.dtb
Keep the above two together:
dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j721e-eaik.dtb
> +
> dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb
>
> dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-eaik.dts b/arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
> new file mode 100644
> index 000000000000..decb16274333
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
> @@ -0,0 +1,342 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
> + */
> +
> +/dts-v1/;
> +
> +#include "k3-j721e.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/net/ti-dp83867.h>
> +
> +/ {
> + compatible = "ti,j721e-eaik", "ti,j721e";
> + model = "Texas Instruments J721E EAIK";
> +
> + chosen {
> + stdout-path = "serial2:115200n8";
> + bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
> + };
> +
> + memory@80000000 {
> + device_type = "memory";
> + /* 4G RAM */
> + reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
> + <0x00000008 0x80000000 0x00000000 0x80000000>;
> + };
> +
> + reserved_memory: reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + secure_ddr: optee@9e800000 {
> + reg = <0x00 0x9e800000 0x00 0x01800000>;
> + alignment = <0x1000>;
> + no-map;
> + };
> + };
> +
> + vusb_main: fixedregulator-vusb-main5v0 {
> + /* USB MAIN INPUT 5V DC */
> + compatible = "regulator-fixed";
> + regulator-name = "vusb-main5v0";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vsys_3v3: fixedregulator-vsys3v3 {
> + /* Output of LM5141 */
> + compatible = "regulator-fixed";
> + regulator-name = "vsys_3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vusb_main>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vdd_mmc1: fixedregulator-sd {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&vdd_mmc1_en_pins_default>;
> + regulator-name = "vdd_mmc1";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + enable-active-high;
> + vin-supply = <&vsys_3v3>;
> + gpio = <&wkup_gpio0 8 GPIO_ACTIVE_HIGH>;
> + };
> +
> + vdd_sd_dv_alt: gpio-regulator-tps659411 {
> + compatible = "regulator-gpio";
> + pinctrl-names = "default";
> + pinctrl-0 = <&vdd_sd_dv_alt_pins_default>;
> + regulator-name = "tps659411";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + vin-supply = <&vsys_3v3>;
> + gpios = <&wkup_gpio0 9 GPIO_ACTIVE_HIGH>;
> + states = <1800000 0x0>,
> + <3300000 0x1>;
> + };
> +};
> +
> +&main_pmx0 {
> + main_mmc1_pins_default: main-mmc1-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0x254, PIN_INPUT, 0) /* (R29) MMC1_CMD */
> + J721E_IOPAD(0x250, PIN_INPUT, 0) /* (P25) MMC1_CLK */
> + J721E_IOPAD(0x2ac, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */
> + J721E_IOPAD(0x24c, PIN_INPUT, 0) /* (R24) MMC1_DAT0 */
> + J721E_IOPAD(0x248, PIN_INPUT, 0) /* (P24) MMC1_DAT1 */
> + J721E_IOPAD(0x244, PIN_INPUT, 0) /* (R25) MMC1_DAT2 */
> + J721E_IOPAD(0x240, PIN_INPUT, 0) /* (R26) MMC1_DAT3 */
> + J721E_IOPAD(0x258, PIN_INPUT, 0) /* (P23) MMC1_SDCD */
> + >;
> + };
> +
> + main_uart0_pins_default: main-uart0-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0x1f0, PIN_INPUT, 0) /* (AC2) UART0_CTSn */
> + J721E_IOPAD(0x1f4, PIN_OUTPUT, 0) /* (AB1) UART0_RTSn */
> + J721E_IOPAD(0x1e8, PIN_INPUT, 0) /* (AB2) UART0_RXD */
> + J721E_IOPAD(0x1ec, PIN_OUTPUT, 0) /* (AB3) UART0_TXD */
> + >;
> + };
> +
> + main_i2c0_pins_default: main-i2c0-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0x220, PIN_INPUT_PULLUP, 0) /* (AC5) I2C0_SCL */
> + J721E_IOPAD(0x224, PIN_INPUT_PULLUP, 0) /* (AA5) I2C0_SDA */
> + >;
> + };
> +
> + main_i2c1_pins_default: main-i2c1-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0x228, PIN_INPUT_PULLUP, 0) /* (Y6) I2C1_SCL */
> + J721E_IOPAD(0x22c, PIN_INPUT_PULLUP, 0) /* (AA6) I2C1_SDA */
> + >;
> + };
> +
> + main_i2c3_pins_default: main-i2c3-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0x270, PIN_INPUT_PULLUP, 4) /* (T26) MMC2_CLK.I2C3_SCL */
> + J721E_IOPAD(0x274, PIN_INPUT_PULLUP, 4) /* (T25) MMC2_CMD.I2C3_SDA */
> + >;
> + };
> +};
> +
> +&wkup_pmx0 {
> + mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
> + pinctrl-single,pins = <
> + J721E_WKUP_IOPAD(0x0, PIN_OUTPUT, 0) /* (E20) MCU_OSPI0_CLK */
> + J721E_WKUP_IOPAD(0x2c, PIN_OUTPUT, 0) /* (F19) MCU_OSPI0_CSn0 */
> + J721E_WKUP_IOPAD(0xc, PIN_INPUT, 0) /* (D20) MCU_OSPI0_D0 */
> + J721E_WKUP_IOPAD(0x10, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D1 */
> + J721E_WKUP_IOPAD(0x14, PIN_INPUT, 0) /* (G20) MCU_OSPI0_D2 */
> + J721E_WKUP_IOPAD(0x18, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D3 */
> + J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 0) /* (F21) MCU_OSPI0_D4 */
> + J721E_WKUP_IOPAD(0x20, PIN_INPUT, 0) /* (E21) MCU_OSPI0_D5 */
> + J721E_WKUP_IOPAD(0x24, PIN_INPUT, 0) /* (B22) MCU_OSPI0_D6 */
> + J721E_WKUP_IOPAD(0x28, PIN_INPUT, 0) /* (G21) MCU_OSPI0_D7 */
> + J721E_WKUP_IOPAD(0x8, PIN_INPUT, 0) /* (D21) MCU_OSPI0_DQS */
> + >;
> + };
> +
> + vdd_mmc1_en_pins_default: vdd-mmc1-en-pins-default {
> + pinctrl-single,pins = <
> + J721E_WKUP_IOPAD(0xd0, PIN_OUTPUT, 7) /* (G27) WKUP_GPIO0_8 */
> + >;
> + };
> +
> + vdd_sd_dv_alt_pins_default: vdd-sd-dv-alt-pins-default {
> + pinctrl-single,pins = <
> + J721E_WKUP_IOPAD(0xd4, PIN_OUTPUT, 7) /* (G26) WKUP_GPIO0_9 */
> + >;
> + };
> +
> + wkup_i2c0_pins_default: wkup-i2c0-pins-default {
> + pinctrl-single,pins = <
> + J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
> + J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
> + >;
> + };
> +};
> +
> +&wkup_uart0 {
> + /* Wakeup UART is used by System firmware */
> + status = "reserved";
> +};
> +
> +&main_uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_uart0_pins_default>;
> + /* Shared with ATF on this platform */
> + power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
> +};
> +
> +&main_uart2 {
> + /* Brought out on RPi header */
> + status = "disabled";
> +};
> +
> +&main_uart3 {
> + /* UART not brought out */
> + status = "disabled";
> +};
> +
> +&main_uart5 {
> + /* UART not brought out */
> + status = "disabled";
> +};
> +
> +&main_uart6 {
> + /* UART not brought out */
> + status = "disabled";
> +};
> +
> +&main_uart7 {
> + /* UART not brought out */
> + status = "disabled";
> +};
> +
> +&main_uart8 {
> + /* UART not brought out */
> + status = "disabled";
> +};
> +
> +&main_uart9 {
> + /* Brought out on M.2 E Key */
> + status = "disabled";
> +};
> +
> +&main_sdhci0 {
> + /* Unused */
> + status = "disabled";
> +};
> +
> +&main_sdhci1 {
> + /* SD Card */
> + vmmc-supply = <&vdd_mmc1>;
> + vqmmc-supply = <&vdd_sd_dv_alt>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_mmc1_pins_default>;
> + ti,driver-strength-ohm = <50>;
> + disable-wp;
> +};
> +
> +&main_sdhci2 {
> + /* Unused */
> + status = "disabled";
> +};
> +
> +&ospi0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
> +
> + flash@0{
flash@0<space>{
> + compatible = "jedec,spi-nor";
> + reg = <0x0>;
> + spi-tx-bus-width = <8>;
> + spi-rx-bus-width = <8>;
> + spi-max-frequency = <25000000>;
> + cdns,tshsl-ns = <60>;
> + cdns,tsd2d-ns = <60>;
> + cdns,tchsh-ns = <60>;
> + cdns,tslch-ns = <60>;
> + cdns,read-delay = <4>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + partition@3fc0000 {
> + label = "ospi.phypattern";
> + reg = <0x3fc0000 0x40000>;
> + u-boot,dm-spl;
> + };
> + };
> +};
> +
> +&ospi1 {
> + /* Unused */
> + status = "disabled";
> +};
> +
> +&main_i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_i2c0_pins_default>;
> + clock-frequency = <400000>;
> +
> + i2c-switch@71 {
> + compatible = "nxp,pca9543";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x71>;
> +
> + /* PCIe1 M.2 M Key I2C */
> + pcie1_m2_i2c: i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + };
> +
> + /* PCIe0 M.2 E Key I2C */
> + pcie0_m2_i2c: i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> + };
> + };
> +};
> +
> +&main_i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_i2c1_pins_default>;
> + clock-frequency = <400000>;
> +};
> +
> +&main_i2c3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_i2c3_pins_default>;
> + clock-frequency = <400000>;
> +
> + i2c-switch@70 {
> + compatible = "nxp,pca9543";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x70>;
> +
> + /* CAM0 I2C */
> + ti_cam0_i2c: i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + };
> +
> + /* CAM1 I2C */
> + rpi_cam0_i2c: i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> + };
> + };
> +};
> +
> +&main_i2c4 {
> + /* Unused */
> + status = "disabled";
> +};
> +
> +&main_i2c5 {
> + /* Brought out on RPi Header */
> + status = "disabled";
> +};
> +
> +&main_i2c6 {
> + /* Unused */
> + status = "disabled";
> +};
please also check other nodes that needs to be disabled or configured.
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH V2 2/2] arm64: dts: ti: Add support for J721E EAIK
@ 2021-06-07 13:35 ` Nishanth Menon
0 siblings, 0 replies; 22+ messages in thread
From: Nishanth Menon @ 2021-06-07 13:35 UTC (permalink / raw)
To: Sinthu Raja
Cc: Tero Kristo, Rob Herring, Device Tree Mailing List,
Linux ARM Mailing List, Lokesh Vutla, Amarnath MB, Sinthu Raja
On 15:03-20210607, Sinthu Raja wrote:
> From: Sinthu Raja <sinthu.raja@ti.com>
>
> J721E EdgeAI Kit (EAIK) is a low cost, small form factor board designed
> for TI’s J721E SoC. TI’s J721E SoC comprises of dual core A72, high
> performance vision accelerators, video codec accelerators, latest C71x
> and C66x DSP, high bandwidth real-time IPs for capture and display, GPU,
> dedicated safety island and security accelerators. The SoC is power
> optimized to provide best in class performance for perception, sensor
> fusion, localization, path planning tasks in robotics, industrial and
> automotive applications.
>
> J721E EAIK supports the following interfaces:
> * 4 GB LPDDR4 RAM
> * x1 Gigabit Ethernet interface
> * x1 USB 3.0 Type-C port
> * x3 USB 3.0 Type-A ports
> * x1 UHS-1 capable µSD card slot
> * x1 PCIe M.2 E Key with x1 USB2.0, x1 MCASP, x1 MMC, x1 UART
> * x1 PCIe M.2 M Key
> * 512 Mbit OSPI flash
> * x4 UART through UART-USB bridge
> * x4 CAN-FD interface
> * x1 DP interface
> * x1 HDMI interface
> * x2 CSI2 Camera interface (RPi and TI Camera connector)
> * 40-pin Raspberry Pi compatible GPIO header
> * Compact TI 20-Pin connector for JTAG debug
> * Interface for remote automation. Includes:
> * power measurement and reset control
> * boot mode change
please reduce the description above, also add a url for the board.
>
> Add basic support for J721E-EAIK.
>
> Signed-off-by: Amarnath MB <amarnath.mb@ti.com>
> Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
> ---
> arch/arm64/boot/dts/ti/Makefile | 2 +
> arch/arm64/boot/dts/ti/k3-j721e-eaik.dts | 342 +++++++++++++++++++++++
> 2 files changed, 344 insertions(+)
> create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
>
> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> index d56c742f5a10..00eb2077616e 100644
> --- a/arch/arm64/boot/dts/ti/Makefile
> +++ b/arch/arm64/boot/dts/ti/Makefile
> @@ -12,6 +12,8 @@ dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb
>
> dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
>
> +dtb-$(CONFIG_ARCH_K3) += k3-j721e-eaik.dtb
Keep the above two together:
dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j721e-eaik.dtb
> +
> dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb
>
> dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-eaik.dts b/arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
> new file mode 100644
> index 000000000000..decb16274333
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
> @@ -0,0 +1,342 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
> + */
> +
> +/dts-v1/;
> +
> +#include "k3-j721e.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/net/ti-dp83867.h>
> +
> +/ {
> + compatible = "ti,j721e-eaik", "ti,j721e";
> + model = "Texas Instruments J721E EAIK";
> +
> + chosen {
> + stdout-path = "serial2:115200n8";
> + bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
> + };
> +
> + memory@80000000 {
> + device_type = "memory";
> + /* 4G RAM */
> + reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
> + <0x00000008 0x80000000 0x00000000 0x80000000>;
> + };
> +
> + reserved_memory: reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + secure_ddr: optee@9e800000 {
> + reg = <0x00 0x9e800000 0x00 0x01800000>;
> + alignment = <0x1000>;
> + no-map;
> + };
> + };
> +
> + vusb_main: fixedregulator-vusb-main5v0 {
> + /* USB MAIN INPUT 5V DC */
> + compatible = "regulator-fixed";
> + regulator-name = "vusb-main5v0";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vsys_3v3: fixedregulator-vsys3v3 {
> + /* Output of LM5141 */
> + compatible = "regulator-fixed";
> + regulator-name = "vsys_3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vusb_main>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vdd_mmc1: fixedregulator-sd {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&vdd_mmc1_en_pins_default>;
> + regulator-name = "vdd_mmc1";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + enable-active-high;
> + vin-supply = <&vsys_3v3>;
> + gpio = <&wkup_gpio0 8 GPIO_ACTIVE_HIGH>;
> + };
> +
> + vdd_sd_dv_alt: gpio-regulator-tps659411 {
> + compatible = "regulator-gpio";
> + pinctrl-names = "default";
> + pinctrl-0 = <&vdd_sd_dv_alt_pins_default>;
> + regulator-name = "tps659411";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + vin-supply = <&vsys_3v3>;
> + gpios = <&wkup_gpio0 9 GPIO_ACTIVE_HIGH>;
> + states = <1800000 0x0>,
> + <3300000 0x1>;
> + };
> +};
> +
> +&main_pmx0 {
> + main_mmc1_pins_default: main-mmc1-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0x254, PIN_INPUT, 0) /* (R29) MMC1_CMD */
> + J721E_IOPAD(0x250, PIN_INPUT, 0) /* (P25) MMC1_CLK */
> + J721E_IOPAD(0x2ac, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */
> + J721E_IOPAD(0x24c, PIN_INPUT, 0) /* (R24) MMC1_DAT0 */
> + J721E_IOPAD(0x248, PIN_INPUT, 0) /* (P24) MMC1_DAT1 */
> + J721E_IOPAD(0x244, PIN_INPUT, 0) /* (R25) MMC1_DAT2 */
> + J721E_IOPAD(0x240, PIN_INPUT, 0) /* (R26) MMC1_DAT3 */
> + J721E_IOPAD(0x258, PIN_INPUT, 0) /* (P23) MMC1_SDCD */
> + >;
> + };
> +
> + main_uart0_pins_default: main-uart0-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0x1f0, PIN_INPUT, 0) /* (AC2) UART0_CTSn */
> + J721E_IOPAD(0x1f4, PIN_OUTPUT, 0) /* (AB1) UART0_RTSn */
> + J721E_IOPAD(0x1e8, PIN_INPUT, 0) /* (AB2) UART0_RXD */
> + J721E_IOPAD(0x1ec, PIN_OUTPUT, 0) /* (AB3) UART0_TXD */
> + >;
> + };
> +
> + main_i2c0_pins_default: main-i2c0-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0x220, PIN_INPUT_PULLUP, 0) /* (AC5) I2C0_SCL */
> + J721E_IOPAD(0x224, PIN_INPUT_PULLUP, 0) /* (AA5) I2C0_SDA */
> + >;
> + };
> +
> + main_i2c1_pins_default: main-i2c1-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0x228, PIN_INPUT_PULLUP, 0) /* (Y6) I2C1_SCL */
> + J721E_IOPAD(0x22c, PIN_INPUT_PULLUP, 0) /* (AA6) I2C1_SDA */
> + >;
> + };
> +
> + main_i2c3_pins_default: main-i2c3-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0x270, PIN_INPUT_PULLUP, 4) /* (T26) MMC2_CLK.I2C3_SCL */
> + J721E_IOPAD(0x274, PIN_INPUT_PULLUP, 4) /* (T25) MMC2_CMD.I2C3_SDA */
> + >;
> + };
> +};
> +
> +&wkup_pmx0 {
> + mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
> + pinctrl-single,pins = <
> + J721E_WKUP_IOPAD(0x0, PIN_OUTPUT, 0) /* (E20) MCU_OSPI0_CLK */
> + J721E_WKUP_IOPAD(0x2c, PIN_OUTPUT, 0) /* (F19) MCU_OSPI0_CSn0 */
> + J721E_WKUP_IOPAD(0xc, PIN_INPUT, 0) /* (D20) MCU_OSPI0_D0 */
> + J721E_WKUP_IOPAD(0x10, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D1 */
> + J721E_WKUP_IOPAD(0x14, PIN_INPUT, 0) /* (G20) MCU_OSPI0_D2 */
> + J721E_WKUP_IOPAD(0x18, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D3 */
> + J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 0) /* (F21) MCU_OSPI0_D4 */
> + J721E_WKUP_IOPAD(0x20, PIN_INPUT, 0) /* (E21) MCU_OSPI0_D5 */
> + J721E_WKUP_IOPAD(0x24, PIN_INPUT, 0) /* (B22) MCU_OSPI0_D6 */
> + J721E_WKUP_IOPAD(0x28, PIN_INPUT, 0) /* (G21) MCU_OSPI0_D7 */
> + J721E_WKUP_IOPAD(0x8, PIN_INPUT, 0) /* (D21) MCU_OSPI0_DQS */
> + >;
> + };
> +
> + vdd_mmc1_en_pins_default: vdd-mmc1-en-pins-default {
> + pinctrl-single,pins = <
> + J721E_WKUP_IOPAD(0xd0, PIN_OUTPUT, 7) /* (G27) WKUP_GPIO0_8 */
> + >;
> + };
> +
> + vdd_sd_dv_alt_pins_default: vdd-sd-dv-alt-pins-default {
> + pinctrl-single,pins = <
> + J721E_WKUP_IOPAD(0xd4, PIN_OUTPUT, 7) /* (G26) WKUP_GPIO0_9 */
> + >;
> + };
> +
> + wkup_i2c0_pins_default: wkup-i2c0-pins-default {
> + pinctrl-single,pins = <
> + J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
> + J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
> + >;
> + };
> +};
> +
> +&wkup_uart0 {
> + /* Wakeup UART is used by System firmware */
> + status = "reserved";
> +};
> +
> +&main_uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_uart0_pins_default>;
> + /* Shared with ATF on this platform */
> + power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
> +};
> +
> +&main_uart2 {
> + /* Brought out on RPi header */
> + status = "disabled";
> +};
> +
> +&main_uart3 {
> + /* UART not brought out */
> + status = "disabled";
> +};
> +
> +&main_uart5 {
> + /* UART not brought out */
> + status = "disabled";
> +};
> +
> +&main_uart6 {
> + /* UART not brought out */
> + status = "disabled";
> +};
> +
> +&main_uart7 {
> + /* UART not brought out */
> + status = "disabled";
> +};
> +
> +&main_uart8 {
> + /* UART not brought out */
> + status = "disabled";
> +};
> +
> +&main_uart9 {
> + /* Brought out on M.2 E Key */
> + status = "disabled";
> +};
> +
> +&main_sdhci0 {
> + /* Unused */
> + status = "disabled";
> +};
> +
> +&main_sdhci1 {
> + /* SD Card */
> + vmmc-supply = <&vdd_mmc1>;
> + vqmmc-supply = <&vdd_sd_dv_alt>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_mmc1_pins_default>;
> + ti,driver-strength-ohm = <50>;
> + disable-wp;
> +};
> +
> +&main_sdhci2 {
> + /* Unused */
> + status = "disabled";
> +};
> +
> +&ospi0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
> +
> + flash@0{
flash@0<space>{
> + compatible = "jedec,spi-nor";
> + reg = <0x0>;
> + spi-tx-bus-width = <8>;
> + spi-rx-bus-width = <8>;
> + spi-max-frequency = <25000000>;
> + cdns,tshsl-ns = <60>;
> + cdns,tsd2d-ns = <60>;
> + cdns,tchsh-ns = <60>;
> + cdns,tslch-ns = <60>;
> + cdns,read-delay = <4>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + partition@3fc0000 {
> + label = "ospi.phypattern";
> + reg = <0x3fc0000 0x40000>;
> + u-boot,dm-spl;
> + };
> + };
> +};
> +
> +&ospi1 {
> + /* Unused */
> + status = "disabled";
> +};
> +
> +&main_i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_i2c0_pins_default>;
> + clock-frequency = <400000>;
> +
> + i2c-switch@71 {
> + compatible = "nxp,pca9543";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x71>;
> +
> + /* PCIe1 M.2 M Key I2C */
> + pcie1_m2_i2c: i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + };
> +
> + /* PCIe0 M.2 E Key I2C */
> + pcie0_m2_i2c: i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> + };
> + };
> +};
> +
> +&main_i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_i2c1_pins_default>;
> + clock-frequency = <400000>;
> +};
> +
> +&main_i2c3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_i2c3_pins_default>;
> + clock-frequency = <400000>;
> +
> + i2c-switch@70 {
> + compatible = "nxp,pca9543";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x70>;
> +
> + /* CAM0 I2C */
> + ti_cam0_i2c: i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + };
> +
> + /* CAM1 I2C */
> + rpi_cam0_i2c: i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> + };
> + };
> +};
> +
> +&main_i2c4 {
> + /* Unused */
> + status = "disabled";
> +};
> +
> +&main_i2c5 {
> + /* Brought out on RPi Header */
> + status = "disabled";
> +};
> +
> +&main_i2c6 {
> + /* Unused */
> + status = "disabled";
> +};
please also check other nodes that needs to be disabled or configured.
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH V2 2/2] arm64: dts: ti: Add support for J721E EAIK
2021-06-07 13:35 ` Nishanth Menon
@ 2021-06-07 17:11 ` Sinthu Raja M
-1 siblings, 0 replies; 22+ messages in thread
From: Sinthu Raja M @ 2021-06-07 17:11 UTC (permalink / raw)
To: Nishanth Menon
Cc: Tero Kristo, Rob Herring, Device Tree Mailing List,
Linux ARM Mailing List, Lokesh Vutla, Amarnath MB, Sinthu Raja
On Mon, Jun 7, 2021 at 7:05 PM Nishanth Menon <nm@ti.com> wrote:
>
> On 15:03-20210607, Sinthu Raja wrote:
> > From: Sinthu Raja <sinthu.raja@ti.com>
> >
> > J721E EdgeAI Kit (EAIK) is a low cost, small form factor board designed
> > for TI’s J721E SoC. TI’s J721E SoC comprises of dual core A72, high
> > performance vision accelerators, video codec accelerators, latest C71x
> > and C66x DSP, high bandwidth real-time IPs for capture and display, GPU,
> > dedicated safety island and security accelerators. The SoC is power
> > optimized to provide best in class performance for perception, sensor
> > fusion, localization, path planning tasks in robotics, industrial and
> > automotive applications.
> >
> > J721E EAIK supports the following interfaces:
> > * 4 GB LPDDR4 RAM
> > * x1 Gigabit Ethernet interface
> > * x1 USB 3.0 Type-C port
> > * x3 USB 3.0 Type-A ports
> > * x1 UHS-1 capable µSD card slot
> > * x1 PCIe M.2 E Key with x1 USB2.0, x1 MCASP, x1 MMC, x1 UART
> > * x1 PCIe M.2 M Key
> > * 512 Mbit OSPI flash
> > * x4 UART through UART-USB bridge
> > * x4 CAN-FD interface
> > * x1 DP interface
> > * x1 HDMI interface
> > * x2 CSI2 Camera interface (RPi and TI Camera connector)
> > * 40-pin Raspberry Pi compatible GPIO header
> > * Compact TI 20-Pin connector for JTAG debug
> > * Interface for remote automation. Includes:
> > * power measurement and reset control
> > * boot mode change
>
> please reduce the description above, also add a url for the board.
Sure will reduce the description. The URL is not available until the
board launch.
> >
> > Add basic support for J721E-EAIK.
> >
> > Signed-off-by: Amarnath MB <amarnath.mb@ti.com>
> > Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
> > ---
> > arch/arm64/boot/dts/ti/Makefile | 2 +
> > arch/arm64/boot/dts/ti/k3-j721e-eaik.dts | 342 +++++++++++++++++++++++
> > 2 files changed, 344 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
> >
> > diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> > index d56c742f5a10..00eb2077616e 100644
> > --- a/arch/arm64/boot/dts/ti/Makefile
> > +++ b/arch/arm64/boot/dts/ti/Makefile
> > @@ -12,6 +12,8 @@ dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb
> >
> > dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
> >
> > +dtb-$(CONFIG_ARCH_K3) += k3-j721e-eaik.dtb
>
> Keep the above two together:
> dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-j721e-eaik.dtb
>
>
> > +
> > dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb
> >
> > dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
> > diff --git a/arch/arm64/boot/dts/ti/k3-j721e-eaik.dts b/arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
> > new file mode 100644
> > index 000000000000..decb16274333
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
> > @@ -0,0 +1,342 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "k3-j721e.dtsi"
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/input/input.h>
> > +#include <dt-bindings/net/ti-dp83867.h>
> > +
> > +/ {
> > + compatible = "ti,j721e-eaik", "ti,j721e";
> > + model = "Texas Instruments J721E EAIK";
> > +
> > + chosen {
> > + stdout-path = "serial2:115200n8";
> > + bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
> > + };
> > +
> > + memory@80000000 {
> > + device_type = "memory";
> > + /* 4G RAM */
> > + reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
> > + <0x00000008 0x80000000 0x00000000 0x80000000>;
> > + };
> > +
> > + reserved_memory: reserved-memory {
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > +
> > + secure_ddr: optee@9e800000 {
> > + reg = <0x00 0x9e800000 0x00 0x01800000>;
> > + alignment = <0x1000>;
> > + no-map;
> > + };
> > + };
> > +
> > + vusb_main: fixedregulator-vusb-main5v0 {
> > + /* USB MAIN INPUT 5V DC */
> > + compatible = "regulator-fixed";
> > + regulator-name = "vusb-main5v0";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + };
> > +
> > + vsys_3v3: fixedregulator-vsys3v3 {
> > + /* Output of LM5141 */
> > + compatible = "regulator-fixed";
> > + regulator-name = "vsys_3v3";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + vin-supply = <&vusb_main>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + };
> > +
> > + vdd_mmc1: fixedregulator-sd {
> > + compatible = "regulator-fixed";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&vdd_mmc1_en_pins_default>;
> > + regulator-name = "vdd_mmc1";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > + enable-active-high;
> > + vin-supply = <&vsys_3v3>;
> > + gpio = <&wkup_gpio0 8 GPIO_ACTIVE_HIGH>;
> > + };
> > +
> > + vdd_sd_dv_alt: gpio-regulator-tps659411 {
> > + compatible = "regulator-gpio";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&vdd_sd_dv_alt_pins_default>;
> > + regulator-name = "tps659411";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > + vin-supply = <&vsys_3v3>;
> > + gpios = <&wkup_gpio0 9 GPIO_ACTIVE_HIGH>;
> > + states = <1800000 0x0>,
> > + <3300000 0x1>;
> > + };
> > +};
> > +
> > +&main_pmx0 {
> > + main_mmc1_pins_default: main-mmc1-pins-default {
> > + pinctrl-single,pins = <
> > + J721E_IOPAD(0x254, PIN_INPUT, 0) /* (R29) MMC1_CMD */
> > + J721E_IOPAD(0x250, PIN_INPUT, 0) /* (P25) MMC1_CLK */
> > + J721E_IOPAD(0x2ac, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */
> > + J721E_IOPAD(0x24c, PIN_INPUT, 0) /* (R24) MMC1_DAT0 */
> > + J721E_IOPAD(0x248, PIN_INPUT, 0) /* (P24) MMC1_DAT1 */
> > + J721E_IOPAD(0x244, PIN_INPUT, 0) /* (R25) MMC1_DAT2 */
> > + J721E_IOPAD(0x240, PIN_INPUT, 0) /* (R26) MMC1_DAT3 */
> > + J721E_IOPAD(0x258, PIN_INPUT, 0) /* (P23) MMC1_SDCD */
> > + >;
> > + };
> > +
> > + main_uart0_pins_default: main-uart0-pins-default {
> > + pinctrl-single,pins = <
> > + J721E_IOPAD(0x1f0, PIN_INPUT, 0) /* (AC2) UART0_CTSn */
> > + J721E_IOPAD(0x1f4, PIN_OUTPUT, 0) /* (AB1) UART0_RTSn */
> > + J721E_IOPAD(0x1e8, PIN_INPUT, 0) /* (AB2) UART0_RXD */
> > + J721E_IOPAD(0x1ec, PIN_OUTPUT, 0) /* (AB3) UART0_TXD */
> > + >;
> > + };
> > +
> > + main_i2c0_pins_default: main-i2c0-pins-default {
> > + pinctrl-single,pins = <
> > + J721E_IOPAD(0x220, PIN_INPUT_PULLUP, 0) /* (AC5) I2C0_SCL */
> > + J721E_IOPAD(0x224, PIN_INPUT_PULLUP, 0) /* (AA5) I2C0_SDA */
> > + >;
> > + };
> > +
> > + main_i2c1_pins_default: main-i2c1-pins-default {
> > + pinctrl-single,pins = <
> > + J721E_IOPAD(0x228, PIN_INPUT_PULLUP, 0) /* (Y6) I2C1_SCL */
> > + J721E_IOPAD(0x22c, PIN_INPUT_PULLUP, 0) /* (AA6) I2C1_SDA */
> > + >;
> > + };
> > +
> > + main_i2c3_pins_default: main-i2c3-pins-default {
> > + pinctrl-single,pins = <
> > + J721E_IOPAD(0x270, PIN_INPUT_PULLUP, 4) /* (T26) MMC2_CLK.I2C3_SCL */
> > + J721E_IOPAD(0x274, PIN_INPUT_PULLUP, 4) /* (T25) MMC2_CMD.I2C3_SDA */
> > + >;
> > + };
> > +};
> > +
> > +&wkup_pmx0 {
> > + mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
> > + pinctrl-single,pins = <
> > + J721E_WKUP_IOPAD(0x0, PIN_OUTPUT, 0) /* (E20) MCU_OSPI0_CLK */
> > + J721E_WKUP_IOPAD(0x2c, PIN_OUTPUT, 0) /* (F19) MCU_OSPI0_CSn0 */
> > + J721E_WKUP_IOPAD(0xc, PIN_INPUT, 0) /* (D20) MCU_OSPI0_D0 */
> > + J721E_WKUP_IOPAD(0x10, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D1 */
> > + J721E_WKUP_IOPAD(0x14, PIN_INPUT, 0) /* (G20) MCU_OSPI0_D2 */
> > + J721E_WKUP_IOPAD(0x18, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D3 */
> > + J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 0) /* (F21) MCU_OSPI0_D4 */
> > + J721E_WKUP_IOPAD(0x20, PIN_INPUT, 0) /* (E21) MCU_OSPI0_D5 */
> > + J721E_WKUP_IOPAD(0x24, PIN_INPUT, 0) /* (B22) MCU_OSPI0_D6 */
> > + J721E_WKUP_IOPAD(0x28, PIN_INPUT, 0) /* (G21) MCU_OSPI0_D7 */
> > + J721E_WKUP_IOPAD(0x8, PIN_INPUT, 0) /* (D21) MCU_OSPI0_DQS */
> > + >;
> > + };
> > +
> > + vdd_mmc1_en_pins_default: vdd-mmc1-en-pins-default {
> > + pinctrl-single,pins = <
> > + J721E_WKUP_IOPAD(0xd0, PIN_OUTPUT, 7) /* (G27) WKUP_GPIO0_8 */
> > + >;
> > + };
> > +
> > + vdd_sd_dv_alt_pins_default: vdd-sd-dv-alt-pins-default {
> > + pinctrl-single,pins = <
> > + J721E_WKUP_IOPAD(0xd4, PIN_OUTPUT, 7) /* (G26) WKUP_GPIO0_9 */
> > + >;
> > + };
> > +
> > + wkup_i2c0_pins_default: wkup-i2c0-pins-default {
> > + pinctrl-single,pins = <
> > + J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
> > + J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
> > + >;
> > + };
> > +};
> > +
> > +&wkup_uart0 {
> > + /* Wakeup UART is used by System firmware */
> > + status = "reserved";
> > +};
> > +
> > +&main_uart0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&main_uart0_pins_default>;
> > + /* Shared with ATF on this platform */
> > + power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
> > +};
> > +
> > +&main_uart2 {
> > + /* Brought out on RPi header */
> > + status = "disabled";
> > +};
> > +
> > +&main_uart3 {
> > + /* UART not brought out */
> > + status = "disabled";
> > +};
> > +
> > +&main_uart5 {
> > + /* UART not brought out */
> > + status = "disabled";
> > +};
> > +
> > +&main_uart6 {
> > + /* UART not brought out */
> > + status = "disabled";
> > +};
> > +
> > +&main_uart7 {
> > + /* UART not brought out */
> > + status = "disabled";
> > +};
> > +
> > +&main_uart8 {
> > + /* UART not brought out */
> > + status = "disabled";
> > +};
> > +
> > +&main_uart9 {
> > + /* Brought out on M.2 E Key */
> > + status = "disabled";
> > +};
> > +
> > +&main_sdhci0 {
> > + /* Unused */
> > + status = "disabled";
> > +};
> > +
> > +&main_sdhci1 {
> > + /* SD Card */
> > + vmmc-supply = <&vdd_mmc1>;
> > + vqmmc-supply = <&vdd_sd_dv_alt>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&main_mmc1_pins_default>;
> > + ti,driver-strength-ohm = <50>;
> > + disable-wp;
> > +};
> > +
> > +&main_sdhci2 {
> > + /* Unused */
> > + status = "disabled";
> > +};
> > +
> > +&ospi0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
> > +
> > + flash@0{
>
> flash@0<space>{
>
> > + compatible = "jedec,spi-nor";
> > + reg = <0x0>;
> > + spi-tx-bus-width = <8>;
> > + spi-rx-bus-width = <8>;
> > + spi-max-frequency = <25000000>;
> > + cdns,tshsl-ns = <60>;
> > + cdns,tsd2d-ns = <60>;
> > + cdns,tchsh-ns = <60>;
> > + cdns,tslch-ns = <60>;
> > + cdns,read-delay = <4>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + partition@3fc0000 {
> > + label = "ospi.phypattern";
> > + reg = <0x3fc0000 0x40000>;
> > + u-boot,dm-spl;
> > + };
> > + };
> > +};
> > +
> > +&ospi1 {
> > + /* Unused */
> > + status = "disabled";
> > +};
> > +
> > +&main_i2c0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&main_i2c0_pins_default>;
> > + clock-frequency = <400000>;
> > +
> > + i2c-switch@71 {
> > + compatible = "nxp,pca9543";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0x71>;
> > +
> > + /* PCIe1 M.2 M Key I2C */
> > + pcie1_m2_i2c: i2c@0 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0>;
> > + };
> > +
> > + /* PCIe0 M.2 E Key I2C */
> > + pcie0_m2_i2c: i2c@1 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <1>;
> > + };
> > + };
> > +};
> > +
> > +&main_i2c1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&main_i2c1_pins_default>;
> > + clock-frequency = <400000>;
> > +};
> > +
> > +&main_i2c3 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&main_i2c3_pins_default>;
> > + clock-frequency = <400000>;
> > +
> > + i2c-switch@70 {
> > + compatible = "nxp,pca9543";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0x70>;
> > +
> > + /* CAM0 I2C */
> > + ti_cam0_i2c: i2c@0 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0>;
> > + };
> > +
> > + /* CAM1 I2C */
> > + rpi_cam0_i2c: i2c@1 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <1>;
> > + };
> > + };
> > +};
> > +
> > +&main_i2c4 {
> > + /* Unused */
> > + status = "disabled";
> > +};
> > +
> > +&main_i2c5 {
> > + /* Brought out on RPi Header */
> > + status = "disabled";
> > +};
> > +
> > +&main_i2c6 {
> > + /* Unused */
> > + status = "disabled";
> > +};
>
> please also check other nodes that needs to be disabled or configured.
The intention of the patch is to keep only the initial support for the
EAIK board. Subsequent patches will be posted as the testing
completes.
Regards
Sinthu Raja
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH V2 2/2] arm64: dts: ti: Add support for J721E EAIK
@ 2021-06-07 17:11 ` Sinthu Raja M
0 siblings, 0 replies; 22+ messages in thread
From: Sinthu Raja M @ 2021-06-07 17:11 UTC (permalink / raw)
To: Nishanth Menon
Cc: Tero Kristo, Rob Herring, Device Tree Mailing List,
Linux ARM Mailing List, Lokesh Vutla, Amarnath MB, Sinthu Raja
On Mon, Jun 7, 2021 at 7:05 PM Nishanth Menon <nm@ti.com> wrote:
>
> On 15:03-20210607, Sinthu Raja wrote:
> > From: Sinthu Raja <sinthu.raja@ti.com>
> >
> > J721E EdgeAI Kit (EAIK) is a low cost, small form factor board designed
> > for TI’s J721E SoC. TI’s J721E SoC comprises of dual core A72, high
> > performance vision accelerators, video codec accelerators, latest C71x
> > and C66x DSP, high bandwidth real-time IPs for capture and display, GPU,
> > dedicated safety island and security accelerators. The SoC is power
> > optimized to provide best in class performance for perception, sensor
> > fusion, localization, path planning tasks in robotics, industrial and
> > automotive applications.
> >
> > J721E EAIK supports the following interfaces:
> > * 4 GB LPDDR4 RAM
> > * x1 Gigabit Ethernet interface
> > * x1 USB 3.0 Type-C port
> > * x3 USB 3.0 Type-A ports
> > * x1 UHS-1 capable µSD card slot
> > * x1 PCIe M.2 E Key with x1 USB2.0, x1 MCASP, x1 MMC, x1 UART
> > * x1 PCIe M.2 M Key
> > * 512 Mbit OSPI flash
> > * x4 UART through UART-USB bridge
> > * x4 CAN-FD interface
> > * x1 DP interface
> > * x1 HDMI interface
> > * x2 CSI2 Camera interface (RPi and TI Camera connector)
> > * 40-pin Raspberry Pi compatible GPIO header
> > * Compact TI 20-Pin connector for JTAG debug
> > * Interface for remote automation. Includes:
> > * power measurement and reset control
> > * boot mode change
>
> please reduce the description above, also add a url for the board.
Sure will reduce the description. The URL is not available until the
board launch.
> >
> > Add basic support for J721E-EAIK.
> >
> > Signed-off-by: Amarnath MB <amarnath.mb@ti.com>
> > Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
> > ---
> > arch/arm64/boot/dts/ti/Makefile | 2 +
> > arch/arm64/boot/dts/ti/k3-j721e-eaik.dts | 342 +++++++++++++++++++++++
> > 2 files changed, 344 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
> >
> > diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> > index d56c742f5a10..00eb2077616e 100644
> > --- a/arch/arm64/boot/dts/ti/Makefile
> > +++ b/arch/arm64/boot/dts/ti/Makefile
> > @@ -12,6 +12,8 @@ dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb
> >
> > dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
> >
> > +dtb-$(CONFIG_ARCH_K3) += k3-j721e-eaik.dtb
>
> Keep the above two together:
> dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-j721e-eaik.dtb
>
>
> > +
> > dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb
> >
> > dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
> > diff --git a/arch/arm64/boot/dts/ti/k3-j721e-eaik.dts b/arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
> > new file mode 100644
> > index 000000000000..decb16274333
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
> > @@ -0,0 +1,342 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "k3-j721e.dtsi"
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/input/input.h>
> > +#include <dt-bindings/net/ti-dp83867.h>
> > +
> > +/ {
> > + compatible = "ti,j721e-eaik", "ti,j721e";
> > + model = "Texas Instruments J721E EAIK";
> > +
> > + chosen {
> > + stdout-path = "serial2:115200n8";
> > + bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
> > + };
> > +
> > + memory@80000000 {
> > + device_type = "memory";
> > + /* 4G RAM */
> > + reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
> > + <0x00000008 0x80000000 0x00000000 0x80000000>;
> > + };
> > +
> > + reserved_memory: reserved-memory {
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > +
> > + secure_ddr: optee@9e800000 {
> > + reg = <0x00 0x9e800000 0x00 0x01800000>;
> > + alignment = <0x1000>;
> > + no-map;
> > + };
> > + };
> > +
> > + vusb_main: fixedregulator-vusb-main5v0 {
> > + /* USB MAIN INPUT 5V DC */
> > + compatible = "regulator-fixed";
> > + regulator-name = "vusb-main5v0";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + };
> > +
> > + vsys_3v3: fixedregulator-vsys3v3 {
> > + /* Output of LM5141 */
> > + compatible = "regulator-fixed";
> > + regulator-name = "vsys_3v3";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + vin-supply = <&vusb_main>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + };
> > +
> > + vdd_mmc1: fixedregulator-sd {
> > + compatible = "regulator-fixed";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&vdd_mmc1_en_pins_default>;
> > + regulator-name = "vdd_mmc1";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > + enable-active-high;
> > + vin-supply = <&vsys_3v3>;
> > + gpio = <&wkup_gpio0 8 GPIO_ACTIVE_HIGH>;
> > + };
> > +
> > + vdd_sd_dv_alt: gpio-regulator-tps659411 {
> > + compatible = "regulator-gpio";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&vdd_sd_dv_alt_pins_default>;
> > + regulator-name = "tps659411";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > + vin-supply = <&vsys_3v3>;
> > + gpios = <&wkup_gpio0 9 GPIO_ACTIVE_HIGH>;
> > + states = <1800000 0x0>,
> > + <3300000 0x1>;
> > + };
> > +};
> > +
> > +&main_pmx0 {
> > + main_mmc1_pins_default: main-mmc1-pins-default {
> > + pinctrl-single,pins = <
> > + J721E_IOPAD(0x254, PIN_INPUT, 0) /* (R29) MMC1_CMD */
> > + J721E_IOPAD(0x250, PIN_INPUT, 0) /* (P25) MMC1_CLK */
> > + J721E_IOPAD(0x2ac, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */
> > + J721E_IOPAD(0x24c, PIN_INPUT, 0) /* (R24) MMC1_DAT0 */
> > + J721E_IOPAD(0x248, PIN_INPUT, 0) /* (P24) MMC1_DAT1 */
> > + J721E_IOPAD(0x244, PIN_INPUT, 0) /* (R25) MMC1_DAT2 */
> > + J721E_IOPAD(0x240, PIN_INPUT, 0) /* (R26) MMC1_DAT3 */
> > + J721E_IOPAD(0x258, PIN_INPUT, 0) /* (P23) MMC1_SDCD */
> > + >;
> > + };
> > +
> > + main_uart0_pins_default: main-uart0-pins-default {
> > + pinctrl-single,pins = <
> > + J721E_IOPAD(0x1f0, PIN_INPUT, 0) /* (AC2) UART0_CTSn */
> > + J721E_IOPAD(0x1f4, PIN_OUTPUT, 0) /* (AB1) UART0_RTSn */
> > + J721E_IOPAD(0x1e8, PIN_INPUT, 0) /* (AB2) UART0_RXD */
> > + J721E_IOPAD(0x1ec, PIN_OUTPUT, 0) /* (AB3) UART0_TXD */
> > + >;
> > + };
> > +
> > + main_i2c0_pins_default: main-i2c0-pins-default {
> > + pinctrl-single,pins = <
> > + J721E_IOPAD(0x220, PIN_INPUT_PULLUP, 0) /* (AC5) I2C0_SCL */
> > + J721E_IOPAD(0x224, PIN_INPUT_PULLUP, 0) /* (AA5) I2C0_SDA */
> > + >;
> > + };
> > +
> > + main_i2c1_pins_default: main-i2c1-pins-default {
> > + pinctrl-single,pins = <
> > + J721E_IOPAD(0x228, PIN_INPUT_PULLUP, 0) /* (Y6) I2C1_SCL */
> > + J721E_IOPAD(0x22c, PIN_INPUT_PULLUP, 0) /* (AA6) I2C1_SDA */
> > + >;
> > + };
> > +
> > + main_i2c3_pins_default: main-i2c3-pins-default {
> > + pinctrl-single,pins = <
> > + J721E_IOPAD(0x270, PIN_INPUT_PULLUP, 4) /* (T26) MMC2_CLK.I2C3_SCL */
> > + J721E_IOPAD(0x274, PIN_INPUT_PULLUP, 4) /* (T25) MMC2_CMD.I2C3_SDA */
> > + >;
> > + };
> > +};
> > +
> > +&wkup_pmx0 {
> > + mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
> > + pinctrl-single,pins = <
> > + J721E_WKUP_IOPAD(0x0, PIN_OUTPUT, 0) /* (E20) MCU_OSPI0_CLK */
> > + J721E_WKUP_IOPAD(0x2c, PIN_OUTPUT, 0) /* (F19) MCU_OSPI0_CSn0 */
> > + J721E_WKUP_IOPAD(0xc, PIN_INPUT, 0) /* (D20) MCU_OSPI0_D0 */
> > + J721E_WKUP_IOPAD(0x10, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D1 */
> > + J721E_WKUP_IOPAD(0x14, PIN_INPUT, 0) /* (G20) MCU_OSPI0_D2 */
> > + J721E_WKUP_IOPAD(0x18, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D3 */
> > + J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 0) /* (F21) MCU_OSPI0_D4 */
> > + J721E_WKUP_IOPAD(0x20, PIN_INPUT, 0) /* (E21) MCU_OSPI0_D5 */
> > + J721E_WKUP_IOPAD(0x24, PIN_INPUT, 0) /* (B22) MCU_OSPI0_D6 */
> > + J721E_WKUP_IOPAD(0x28, PIN_INPUT, 0) /* (G21) MCU_OSPI0_D7 */
> > + J721E_WKUP_IOPAD(0x8, PIN_INPUT, 0) /* (D21) MCU_OSPI0_DQS */
> > + >;
> > + };
> > +
> > + vdd_mmc1_en_pins_default: vdd-mmc1-en-pins-default {
> > + pinctrl-single,pins = <
> > + J721E_WKUP_IOPAD(0xd0, PIN_OUTPUT, 7) /* (G27) WKUP_GPIO0_8 */
> > + >;
> > + };
> > +
> > + vdd_sd_dv_alt_pins_default: vdd-sd-dv-alt-pins-default {
> > + pinctrl-single,pins = <
> > + J721E_WKUP_IOPAD(0xd4, PIN_OUTPUT, 7) /* (G26) WKUP_GPIO0_9 */
> > + >;
> > + };
> > +
> > + wkup_i2c0_pins_default: wkup-i2c0-pins-default {
> > + pinctrl-single,pins = <
> > + J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
> > + J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
> > + >;
> > + };
> > +};
> > +
> > +&wkup_uart0 {
> > + /* Wakeup UART is used by System firmware */
> > + status = "reserved";
> > +};
> > +
> > +&main_uart0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&main_uart0_pins_default>;
> > + /* Shared with ATF on this platform */
> > + power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
> > +};
> > +
> > +&main_uart2 {
> > + /* Brought out on RPi header */
> > + status = "disabled";
> > +};
> > +
> > +&main_uart3 {
> > + /* UART not brought out */
> > + status = "disabled";
> > +};
> > +
> > +&main_uart5 {
> > + /* UART not brought out */
> > + status = "disabled";
> > +};
> > +
> > +&main_uart6 {
> > + /* UART not brought out */
> > + status = "disabled";
> > +};
> > +
> > +&main_uart7 {
> > + /* UART not brought out */
> > + status = "disabled";
> > +};
> > +
> > +&main_uart8 {
> > + /* UART not brought out */
> > + status = "disabled";
> > +};
> > +
> > +&main_uart9 {
> > + /* Brought out on M.2 E Key */
> > + status = "disabled";
> > +};
> > +
> > +&main_sdhci0 {
> > + /* Unused */
> > + status = "disabled";
> > +};
> > +
> > +&main_sdhci1 {
> > + /* SD Card */
> > + vmmc-supply = <&vdd_mmc1>;
> > + vqmmc-supply = <&vdd_sd_dv_alt>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&main_mmc1_pins_default>;
> > + ti,driver-strength-ohm = <50>;
> > + disable-wp;
> > +};
> > +
> > +&main_sdhci2 {
> > + /* Unused */
> > + status = "disabled";
> > +};
> > +
> > +&ospi0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
> > +
> > + flash@0{
>
> flash@0<space>{
>
> > + compatible = "jedec,spi-nor";
> > + reg = <0x0>;
> > + spi-tx-bus-width = <8>;
> > + spi-rx-bus-width = <8>;
> > + spi-max-frequency = <25000000>;
> > + cdns,tshsl-ns = <60>;
> > + cdns,tsd2d-ns = <60>;
> > + cdns,tchsh-ns = <60>;
> > + cdns,tslch-ns = <60>;
> > + cdns,read-delay = <4>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + partition@3fc0000 {
> > + label = "ospi.phypattern";
> > + reg = <0x3fc0000 0x40000>;
> > + u-boot,dm-spl;
> > + };
> > + };
> > +};
> > +
> > +&ospi1 {
> > + /* Unused */
> > + status = "disabled";
> > +};
> > +
> > +&main_i2c0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&main_i2c0_pins_default>;
> > + clock-frequency = <400000>;
> > +
> > + i2c-switch@71 {
> > + compatible = "nxp,pca9543";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0x71>;
> > +
> > + /* PCIe1 M.2 M Key I2C */
> > + pcie1_m2_i2c: i2c@0 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0>;
> > + };
> > +
> > + /* PCIe0 M.2 E Key I2C */
> > + pcie0_m2_i2c: i2c@1 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <1>;
> > + };
> > + };
> > +};
> > +
> > +&main_i2c1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&main_i2c1_pins_default>;
> > + clock-frequency = <400000>;
> > +};
> > +
> > +&main_i2c3 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&main_i2c3_pins_default>;
> > + clock-frequency = <400000>;
> > +
> > + i2c-switch@70 {
> > + compatible = "nxp,pca9543";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0x70>;
> > +
> > + /* CAM0 I2C */
> > + ti_cam0_i2c: i2c@0 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0>;
> > + };
> > +
> > + /* CAM1 I2C */
> > + rpi_cam0_i2c: i2c@1 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <1>;
> > + };
> > + };
> > +};
> > +
> > +&main_i2c4 {
> > + /* Unused */
> > + status = "disabled";
> > +};
> > +
> > +&main_i2c5 {
> > + /* Brought out on RPi Header */
> > + status = "disabled";
> > +};
> > +
> > +&main_i2c6 {
> > + /* Unused */
> > + status = "disabled";
> > +};
>
> please also check other nodes that needs to be disabled or configured.
The intention of the patch is to keep only the initial support for the
EAIK board. Subsequent patches will be posted as the testing
completes.
Regards
Sinthu Raja
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH V2 2/2] arm64: dts: ti: Add support for J721E EAIK
2021-06-07 17:11 ` Sinthu Raja M
@ 2021-06-07 20:22 ` Nishanth Menon
-1 siblings, 0 replies; 22+ messages in thread
From: Nishanth Menon @ 2021-06-07 20:22 UTC (permalink / raw)
To: Sinthu Raja M
Cc: Tero Kristo, Rob Herring, Device Tree Mailing List,
Linux ARM Mailing List, Lokesh Vutla, Amarnath MB, Sinthu Raja
On 22:41-20210607, Sinthu Raja M wrote:
> On Mon, Jun 7, 2021 at 7:05 PM Nishanth Menon <nm@ti.com> wrote:
> >
> > On 15:03-20210607, Sinthu Raja wrote:
> > > From: Sinthu Raja <sinthu.raja@ti.com>
> > >
> > > J721E EdgeAI Kit (EAIK) is a low cost, small form factor board designed
> > > for TI’s J721E SoC. TI’s J721E SoC comprises of dual core A72, high
> > > performance vision accelerators, video codec accelerators, latest C71x
> > > and C66x DSP, high bandwidth real-time IPs for capture and display, GPU,
> > > dedicated safety island and security accelerators. The SoC is power
> > > optimized to provide best in class performance for perception, sensor
> > > fusion, localization, path planning tasks in robotics, industrial and
> > > automotive applications.
> > >
> > > J721E EAIK supports the following interfaces:
> > > * 4 GB LPDDR4 RAM
> > > * x1 Gigabit Ethernet interface
> > > * x1 USB 3.0 Type-C port
> > > * x3 USB 3.0 Type-A ports
> > > * x1 UHS-1 capable µSD card slot
> > > * x1 PCIe M.2 E Key with x1 USB2.0, x1 MCASP, x1 MMC, x1 UART
> > > * x1 PCIe M.2 M Key
> > > * 512 Mbit OSPI flash
> > > * x4 UART through UART-USB bridge
> > > * x4 CAN-FD interface
> > > * x1 DP interface
> > > * x1 HDMI interface
> > > * x2 CSI2 Camera interface (RPi and TI Camera connector)
> > > * 40-pin Raspberry Pi compatible GPIO header
> > > * Compact TI 20-Pin connector for JTAG debug
> > > * Interface for remote automation. Includes:
> > > * power measurement and reset control
> > > * boot mode change
> >
> > please reduce the description above, also add a url for the board.
>
> Sure will reduce the description. The URL is not available until the
> board launch.
>
[...]
> >
> > please also check other nodes that needs to be disabled or configured.
>
> The intention of the patch is to keep only the initial support for the
> EAIK board. Subsequent patches will be posted as the testing
> completes.
For the nodes that are present in k.org, we should probably make up our
minds as to what needs to be the configuration. While I understand
incremental patches, please look through the list to make sure low
hanging items are addressed at the earliest. Commit message makes one
feel that there is tons of nodes that are probably functional, but your
response makes me feel, that is probably not the case - it is hard to
distinguish between the two.
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH V2 2/2] arm64: dts: ti: Add support for J721E EAIK
@ 2021-06-07 20:22 ` Nishanth Menon
0 siblings, 0 replies; 22+ messages in thread
From: Nishanth Menon @ 2021-06-07 20:22 UTC (permalink / raw)
To: Sinthu Raja M
Cc: Tero Kristo, Rob Herring, Device Tree Mailing List,
Linux ARM Mailing List, Lokesh Vutla, Amarnath MB, Sinthu Raja
On 22:41-20210607, Sinthu Raja M wrote:
> On Mon, Jun 7, 2021 at 7:05 PM Nishanth Menon <nm@ti.com> wrote:
> >
> > On 15:03-20210607, Sinthu Raja wrote:
> > > From: Sinthu Raja <sinthu.raja@ti.com>
> > >
> > > J721E EdgeAI Kit (EAIK) is a low cost, small form factor board designed
> > > for TI’s J721E SoC. TI’s J721E SoC comprises of dual core A72, high
> > > performance vision accelerators, video codec accelerators, latest C71x
> > > and C66x DSP, high bandwidth real-time IPs for capture and display, GPU,
> > > dedicated safety island and security accelerators. The SoC is power
> > > optimized to provide best in class performance for perception, sensor
> > > fusion, localization, path planning tasks in robotics, industrial and
> > > automotive applications.
> > >
> > > J721E EAIK supports the following interfaces:
> > > * 4 GB LPDDR4 RAM
> > > * x1 Gigabit Ethernet interface
> > > * x1 USB 3.0 Type-C port
> > > * x3 USB 3.0 Type-A ports
> > > * x1 UHS-1 capable µSD card slot
> > > * x1 PCIe M.2 E Key with x1 USB2.0, x1 MCASP, x1 MMC, x1 UART
> > > * x1 PCIe M.2 M Key
> > > * 512 Mbit OSPI flash
> > > * x4 UART through UART-USB bridge
> > > * x4 CAN-FD interface
> > > * x1 DP interface
> > > * x1 HDMI interface
> > > * x2 CSI2 Camera interface (RPi and TI Camera connector)
> > > * 40-pin Raspberry Pi compatible GPIO header
> > > * Compact TI 20-Pin connector for JTAG debug
> > > * Interface for remote automation. Includes:
> > > * power measurement and reset control
> > > * boot mode change
> >
> > please reduce the description above, also add a url for the board.
>
> Sure will reduce the description. The URL is not available until the
> board launch.
>
[...]
> >
> > please also check other nodes that needs to be disabled or configured.
>
> The intention of the patch is to keep only the initial support for the
> EAIK board. Subsequent patches will be posted as the testing
> completes.
For the nodes that are present in k.org, we should probably make up our
minds as to what needs to be the configuration. While I understand
incremental patches, please look through the list to make sure low
hanging items are addressed at the earliest. Commit message makes one
feel that there is tons of nodes that are probably functional, but your
response makes me feel, that is probably not the case - it is hard to
distinguish between the two.
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH V2 2/2] arm64: dts: ti: Add support for J721E EAIK
2021-06-07 9:33 ` Sinthu Raja
@ 2021-06-09 13:41 ` Vignesh Raghavendra
-1 siblings, 0 replies; 22+ messages in thread
From: Vignesh Raghavendra @ 2021-06-09 13:41 UTC (permalink / raw)
To: Sinthu Raja, Nishanth Menon, Tero Kristo, Rob Herring
Cc: Device Tree Mailing List, Linux ARM Mailing List, Lokesh Vutla,
Amarnath MB, Sinthu Raja
Hi,
On 6/7/21 3:03 PM, Sinthu Raja wrote:
> +
> +&ospi0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
> +
> + flash@0{
> + compatible = "jedec,spi-nor";
> + reg = <0x0>;
> + spi-tx-bus-width = <8>;
> + spi-rx-bus-width = <8>;
> + spi-max-frequency = <25000000>;
> + cdns,tshsl-ns = <60>;
> + cdns,tsd2d-ns = <60>;
> + cdns,tchsh-ns = <60>;
> + cdns,tslch-ns = <60>;
> + cdns,read-delay = <4>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + partition@3fc0000 {
> + label = "ospi.phypattern";
> + reg = <0x3fc0000 0x40000>;
> + u-boot,dm-spl;
> + };
OSPI PHY calibration support is not yet final in mainline. Please drop
partition@3fc0000
Also, please drop u-boot,dm-spl here and elsewhere. This is U-Boot
specific property.
> + };
> +};
> +
> +&ospi1 {
> + /* Unused */
> + status = "disabled";
> +};
> +
Regards
Vignesh
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH V2 2/2] arm64: dts: ti: Add support for J721E EAIK
@ 2021-06-09 13:41 ` Vignesh Raghavendra
0 siblings, 0 replies; 22+ messages in thread
From: Vignesh Raghavendra @ 2021-06-09 13:41 UTC (permalink / raw)
To: Sinthu Raja, Nishanth Menon, Tero Kristo, Rob Herring
Cc: Device Tree Mailing List, Linux ARM Mailing List, Lokesh Vutla,
Amarnath MB, Sinthu Raja
Hi,
On 6/7/21 3:03 PM, Sinthu Raja wrote:
> +
> +&ospi0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
> +
> + flash@0{
> + compatible = "jedec,spi-nor";
> + reg = <0x0>;
> + spi-tx-bus-width = <8>;
> + spi-rx-bus-width = <8>;
> + spi-max-frequency = <25000000>;
> + cdns,tshsl-ns = <60>;
> + cdns,tsd2d-ns = <60>;
> + cdns,tchsh-ns = <60>;
> + cdns,tslch-ns = <60>;
> + cdns,read-delay = <4>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + partition@3fc0000 {
> + label = "ospi.phypattern";
> + reg = <0x3fc0000 0x40000>;
> + u-boot,dm-spl;
> + };
OSPI PHY calibration support is not yet final in mainline. Please drop
partition@3fc0000
Also, please drop u-boot,dm-spl here and elsewhere. This is U-Boot
specific property.
> + };
> +};
> +
> +&ospi1 {
> + /* Unused */
> + status = "disabled";
> +};
> +
Regards
Vignesh
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 22+ messages in thread