* [PATCH net-next v5 0/8] provide cable test support for the ksz886x switch
@ 2021-06-14 4:31 Oleksij Rempel
2021-06-14 4:31 ` [PATCH net-next v5 1/8] net: phy: micrel: move phy reg offsets to common header Oleksij Rempel
` (8 more replies)
0 siblings, 9 replies; 10+ messages in thread
From: Oleksij Rempel @ 2021-06-14 4:31 UTC (permalink / raw)
To: Woojung Huh, UNGLinuxDriver, Andrew Lunn, Florian Fainelli,
Vivien Didelot, Vladimir Oltean, David S. Miller, Jakub Kicinski
Cc: Oleksij Rempel, kernel, netdev, linux-kernel, Russell King,
Michael Grzeschik
changes v5:
- drop resume() patch
- add Reviewed-by tags.
- rework dsa_slave_phy_connect() patch
changes v4:
- use fallthrough;
- use EOPNOTSUPP instead of ENOTSUPP
- drop flags variable in dsa_slave_phy_connect patch
- extend description for the "net: phy: micrel: apply resume errat"
patch
- fix "use consistent alignments" patch
changes v3:
- remove RFC tag
changes v2:
- use generic MII_* defines where possible
- rework phylink validate
- remove phylink get state function
- reorder cabletest patches to make PHY flag patch in the right order
- fix MDI-X detection
This patches provide support for cable testing on the ksz886x switches.
Since it has one special port, we needed to add phylink with validation
and extra quirk for the PHY to signal, that one port will not provide
valid cable testing reports.
Michael Grzeschik (2):
net: phy: micrel: move phy reg offsets to common header
net: dsa: microchip: ksz8795: add phylink support
Oleksij Rempel (6):
net: phy: micrel: use consistent alignments
net: phy/dsa micrel/ksz886x add MDI-X support
net: phy: micrel: ksz8081 add MDI-X support
net: dsa: microchip: ksz8795: add LINK_MD register support
net: dsa: dsa_slave_phy_connect(): extend phy's flags with port
specific phy flags
net: phy: micrel: ksz886x/ksz8081: add cabletest support
drivers/net/dsa/microchip/ksz8795.c | 214 +++++++++----
drivers/net/dsa/microchip/ksz8795_reg.h | 67 +---
drivers/net/ethernet/micrel/ksz884x.c | 105 +------
drivers/net/phy/micrel.c | 401 ++++++++++++++++++++++--
include/linux/micrel_phy.h | 16 +
net/dsa/slave.c | 7 +-
6 files changed, 573 insertions(+), 237 deletions(-)
--
2.29.2
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH net-next v5 1/8] net: phy: micrel: move phy reg offsets to common header
2021-06-14 4:31 [PATCH net-next v5 0/8] provide cable test support for the ksz886x switch Oleksij Rempel
@ 2021-06-14 4:31 ` Oleksij Rempel
2021-06-14 4:31 ` [PATCH net-next v5 2/8] net: dsa: microchip: ksz8795: add phylink support Oleksij Rempel
` (7 subsequent siblings)
8 siblings, 0 replies; 10+ messages in thread
From: Oleksij Rempel @ 2021-06-14 4:31 UTC (permalink / raw)
To: Woojung Huh, UNGLinuxDriver, Andrew Lunn, Florian Fainelli,
Vivien Didelot, Vladimir Oltean, David S. Miller, Jakub Kicinski
Cc: Michael Grzeschik, Oleksij Rempel, kernel, netdev, linux-kernel,
Russell King
From: Michael Grzeschik <m.grzeschik@pengutronix.de>
Some micrel devices share the same PHY register defines. This patch
moves them to one common header so other drivers can reuse them.
And reuse generic MII_* defines where possible.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/dsa/microchip/ksz8795.c | 119 ++++++++++++------------
drivers/net/dsa/microchip/ksz8795_reg.h | 62 ------------
drivers/net/ethernet/micrel/ksz884x.c | 105 +++------------------
include/linux/micrel_phy.h | 13 +++
4 files changed, 88 insertions(+), 211 deletions(-)
diff --git a/drivers/net/dsa/microchip/ksz8795.c b/drivers/net/dsa/microchip/ksz8795.c
index ad509a57a945..ba065003623f 100644
--- a/drivers/net/dsa/microchip/ksz8795.c
+++ b/drivers/net/dsa/microchip/ksz8795.c
@@ -15,6 +15,7 @@
#include <linux/phy.h>
#include <linux/etherdevice.h>
#include <linux/if_bridge.h>
+#include <linux/micrel_phy.h>
#include <net/dsa.h>
#include <net/switchdev.h>
@@ -731,88 +732,88 @@ static void ksz8_r_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 *val)
u8 p = phy;
switch (reg) {
- case PHY_REG_CTRL:
+ case MII_BMCR:
ksz_pread8(dev, p, regs[P_NEG_RESTART_CTRL], &restart);
ksz_pread8(dev, p, regs[P_SPEED_STATUS], &speed);
ksz_pread8(dev, p, regs[P_FORCE_CTRL], &ctrl);
if (restart & PORT_PHY_LOOPBACK)
- data |= PHY_LOOPBACK;
+ data |= BMCR_LOOPBACK;
if (ctrl & PORT_FORCE_100_MBIT)
- data |= PHY_SPEED_100MBIT;
+ data |= BMCR_SPEED100;
if (ksz_is_ksz88x3(dev)) {
if ((ctrl & PORT_AUTO_NEG_ENABLE))
- data |= PHY_AUTO_NEG_ENABLE;
+ data |= BMCR_ANENABLE;
} else {
if (!(ctrl & PORT_AUTO_NEG_DISABLE))
- data |= PHY_AUTO_NEG_ENABLE;
+ data |= BMCR_ANENABLE;
}
if (restart & PORT_POWER_DOWN)
- data |= PHY_POWER_DOWN;
+ data |= BMCR_PDOWN;
if (restart & PORT_AUTO_NEG_RESTART)
- data |= PHY_AUTO_NEG_RESTART;
+ data |= BMCR_ANRESTART;
if (ctrl & PORT_FORCE_FULL_DUPLEX)
- data |= PHY_FULL_DUPLEX;
+ data |= BMCR_FULLDPLX;
if (speed & PORT_HP_MDIX)
- data |= PHY_HP_MDIX;
+ data |= KSZ886X_BMCR_HP_MDIX;
if (restart & PORT_FORCE_MDIX)
- data |= PHY_FORCE_MDIX;
+ data |= KSZ886X_BMCR_FORCE_MDI;
if (restart & PORT_AUTO_MDIX_DISABLE)
- data |= PHY_AUTO_MDIX_DISABLE;
+ data |= KSZ886X_BMCR_DISABLE_AUTO_MDIX;
if (restart & PORT_TX_DISABLE)
- data |= PHY_TRANSMIT_DISABLE;
+ data |= KSZ886X_BMCR_DISABLE_TRANSMIT;
if (restart & PORT_LED_OFF)
- data |= PHY_LED_DISABLE;
+ data |= KSZ886X_BMCR_DISABLE_LED;
break;
- case PHY_REG_STATUS:
+ case MII_BMSR:
ksz_pread8(dev, p, regs[P_LINK_STATUS], &link);
- data = PHY_100BTX_FD_CAPABLE |
- PHY_100BTX_CAPABLE |
- PHY_10BT_FD_CAPABLE |
- PHY_10BT_CAPABLE |
- PHY_AUTO_NEG_CAPABLE;
+ data = BMSR_100FULL |
+ BMSR_100HALF |
+ BMSR_10FULL |
+ BMSR_10HALF |
+ BMSR_ANEGCAPABLE;
if (link & PORT_AUTO_NEG_COMPLETE)
- data |= PHY_AUTO_NEG_ACKNOWLEDGE;
+ data |= BMSR_ANEGCOMPLETE;
if (link & PORT_STAT_LINK_GOOD)
- data |= PHY_LINK_STATUS;
+ data |= BMSR_LSTATUS;
break;
- case PHY_REG_ID_1:
+ case MII_PHYSID1:
data = KSZ8795_ID_HI;
break;
- case PHY_REG_ID_2:
+ case MII_PHYSID2:
if (ksz_is_ksz88x3(dev))
data = KSZ8863_ID_LO;
else
data = KSZ8795_ID_LO;
break;
- case PHY_REG_AUTO_NEGOTIATION:
+ case MII_ADVERTISE:
ksz_pread8(dev, p, regs[P_LOCAL_CTRL], &ctrl);
- data = PHY_AUTO_NEG_802_3;
+ data = ADVERTISE_CSMA;
if (ctrl & PORT_AUTO_NEG_SYM_PAUSE)
- data |= PHY_AUTO_NEG_SYM_PAUSE;
+ data |= ADVERTISE_PAUSE_CAP;
if (ctrl & PORT_AUTO_NEG_100BTX_FD)
- data |= PHY_AUTO_NEG_100BTX_FD;
+ data |= ADVERTISE_100FULL;
if (ctrl & PORT_AUTO_NEG_100BTX)
- data |= PHY_AUTO_NEG_100BTX;
+ data |= ADVERTISE_100HALF;
if (ctrl & PORT_AUTO_NEG_10BT_FD)
- data |= PHY_AUTO_NEG_10BT_FD;
+ data |= ADVERTISE_10FULL;
if (ctrl & PORT_AUTO_NEG_10BT)
- data |= PHY_AUTO_NEG_10BT;
+ data |= ADVERTISE_10HALF;
break;
- case PHY_REG_REMOTE_CAPABILITY:
+ case MII_LPA:
ksz_pread8(dev, p, regs[P_REMOTE_STATUS], &link);
- data = PHY_AUTO_NEG_802_3;
+ data = LPA_SLCT;
if (link & PORT_REMOTE_SYM_PAUSE)
- data |= PHY_AUTO_NEG_SYM_PAUSE;
+ data |= LPA_PAUSE_CAP;
if (link & PORT_REMOTE_100BTX_FD)
- data |= PHY_AUTO_NEG_100BTX_FD;
+ data |= LPA_100FULL;
if (link & PORT_REMOTE_100BTX)
- data |= PHY_AUTO_NEG_100BTX;
+ data |= LPA_100HALF;
if (link & PORT_REMOTE_10BT_FD)
- data |= PHY_AUTO_NEG_10BT_FD;
+ data |= LPA_10FULL;
if (link & PORT_REMOTE_10BT)
- data |= PHY_AUTO_NEG_10BT;
- if (data & ~PHY_AUTO_NEG_802_3)
- data |= PHY_REMOTE_ACKNOWLEDGE_NOT;
+ data |= LPA_10HALF;
+ if (data & ~LPA_SLCT)
+ data |= LPA_LPACK;
break;
default:
processed = false;
@@ -830,14 +831,14 @@ static void ksz8_w_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 val)
u8 p = phy;
switch (reg) {
- case PHY_REG_CTRL:
+ case MII_BMCR:
/* Do not support PHY reset function. */
- if (val & PHY_RESET)
+ if (val & BMCR_RESET)
break;
ksz_pread8(dev, p, regs[P_SPEED_STATUS], &speed);
data = speed;
- if (val & PHY_HP_MDIX)
+ if (val & KSZ886X_BMCR_HP_MDIX)
data |= PORT_HP_MDIX;
else
data &= ~PORT_HP_MDIX;
@@ -846,12 +847,12 @@ static void ksz8_w_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 val)
ksz_pread8(dev, p, regs[P_FORCE_CTRL], &ctrl);
data = ctrl;
if (ksz_is_ksz88x3(dev)) {
- if ((val & PHY_AUTO_NEG_ENABLE))
+ if ((val & BMCR_ANENABLE))
data |= PORT_AUTO_NEG_ENABLE;
else
data &= ~PORT_AUTO_NEG_ENABLE;
} else {
- if (!(val & PHY_AUTO_NEG_ENABLE))
+ if (!(val & BMCR_ANENABLE))
data |= PORT_AUTO_NEG_DISABLE;
else
data &= ~PORT_AUTO_NEG_DISABLE;
@@ -861,11 +862,11 @@ static void ksz8_w_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 val)
data |= PORT_AUTO_NEG_DISABLE;
}
- if (val & PHY_SPEED_100MBIT)
+ if (val & BMCR_SPEED100)
data |= PORT_FORCE_100_MBIT;
else
data &= ~PORT_FORCE_100_MBIT;
- if (val & PHY_FULL_DUPLEX)
+ if (val & BMCR_FULLDPLX)
data |= PORT_FORCE_FULL_DUPLEX;
else
data &= ~PORT_FORCE_FULL_DUPLEX;
@@ -873,38 +874,38 @@ static void ksz8_w_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 val)
ksz_pwrite8(dev, p, regs[P_FORCE_CTRL], data);
ksz_pread8(dev, p, regs[P_NEG_RESTART_CTRL], &restart);
data = restart;
- if (val & PHY_LED_DISABLE)
+ if (val & KSZ886X_BMCR_DISABLE_LED)
data |= PORT_LED_OFF;
else
data &= ~PORT_LED_OFF;
- if (val & PHY_TRANSMIT_DISABLE)
+ if (val & KSZ886X_BMCR_DISABLE_TRANSMIT)
data |= PORT_TX_DISABLE;
else
data &= ~PORT_TX_DISABLE;
- if (val & PHY_AUTO_NEG_RESTART)
+ if (val & BMCR_ANRESTART)
data |= PORT_AUTO_NEG_RESTART;
else
data &= ~(PORT_AUTO_NEG_RESTART);
- if (val & PHY_POWER_DOWN)
+ if (val & BMCR_PDOWN)
data |= PORT_POWER_DOWN;
else
data &= ~PORT_POWER_DOWN;
- if (val & PHY_AUTO_MDIX_DISABLE)
+ if (val & KSZ886X_BMCR_DISABLE_AUTO_MDIX)
data |= PORT_AUTO_MDIX_DISABLE;
else
data &= ~PORT_AUTO_MDIX_DISABLE;
- if (val & PHY_FORCE_MDIX)
+ if (val & KSZ886X_BMCR_FORCE_MDI)
data |= PORT_FORCE_MDIX;
else
data &= ~PORT_FORCE_MDIX;
- if (val & PHY_LOOPBACK)
+ if (val & BMCR_LOOPBACK)
data |= PORT_PHY_LOOPBACK;
else
data &= ~PORT_PHY_LOOPBACK;
if (data != restart)
ksz_pwrite8(dev, p, regs[P_NEG_RESTART_CTRL], data);
break;
- case PHY_REG_AUTO_NEGOTIATION:
+ case MII_ADVERTISE:
ksz_pread8(dev, p, regs[P_LOCAL_CTRL], &ctrl);
data = ctrl;
data &= ~(PORT_AUTO_NEG_SYM_PAUSE |
@@ -912,15 +913,15 @@ static void ksz8_w_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 val)
PORT_AUTO_NEG_100BTX |
PORT_AUTO_NEG_10BT_FD |
PORT_AUTO_NEG_10BT);
- if (val & PHY_AUTO_NEG_SYM_PAUSE)
+ if (val & ADVERTISE_PAUSE_CAP)
data |= PORT_AUTO_NEG_SYM_PAUSE;
- if (val & PHY_AUTO_NEG_100BTX_FD)
+ if (val & ADVERTISE_100FULL)
data |= PORT_AUTO_NEG_100BTX_FD;
- if (val & PHY_AUTO_NEG_100BTX)
+ if (val & ADVERTISE_100HALF)
data |= PORT_AUTO_NEG_100BTX;
- if (val & PHY_AUTO_NEG_10BT_FD)
+ if (val & ADVERTISE_10FULL)
data |= PORT_AUTO_NEG_10BT_FD;
- if (val & PHY_AUTO_NEG_10BT)
+ if (val & ADVERTISE_10HALF)
data |= PORT_AUTO_NEG_10BT;
if (data != ctrl)
ksz_pwrite8(dev, p, regs[P_LOCAL_CTRL], data);
diff --git a/drivers/net/dsa/microchip/ksz8795_reg.h b/drivers/net/dsa/microchip/ksz8795_reg.h
index c2e52c40a54c..f925ddee5238 100644
--- a/drivers/net/dsa/microchip/ksz8795_reg.h
+++ b/drivers/net/dsa/microchip/ksz8795_reg.h
@@ -744,68 +744,6 @@
#define PORT_ACL_FORCE_DLR_MISS BIT(0)
-#ifndef PHY_REG_CTRL
-#define PHY_REG_CTRL 0
-
-#define PHY_RESET BIT(15)
-#define PHY_LOOPBACK BIT(14)
-#define PHY_SPEED_100MBIT BIT(13)
-#define PHY_AUTO_NEG_ENABLE BIT(12)
-#define PHY_POWER_DOWN BIT(11)
-#define PHY_MII_DISABLE BIT(10)
-#define PHY_AUTO_NEG_RESTART BIT(9)
-#define PHY_FULL_DUPLEX BIT(8)
-#define PHY_COLLISION_TEST_NOT BIT(7)
-#define PHY_HP_MDIX BIT(5)
-#define PHY_FORCE_MDIX BIT(4)
-#define PHY_AUTO_MDIX_DISABLE BIT(3)
-#define PHY_REMOTE_FAULT_DISABLE BIT(2)
-#define PHY_TRANSMIT_DISABLE BIT(1)
-#define PHY_LED_DISABLE BIT(0)
-
-#define PHY_REG_STATUS 1
-
-#define PHY_100BT4_CAPABLE BIT(15)
-#define PHY_100BTX_FD_CAPABLE BIT(14)
-#define PHY_100BTX_CAPABLE BIT(13)
-#define PHY_10BT_FD_CAPABLE BIT(12)
-#define PHY_10BT_CAPABLE BIT(11)
-#define PHY_MII_SUPPRESS_CAPABLE_NOT BIT(6)
-#define PHY_AUTO_NEG_ACKNOWLEDGE BIT(5)
-#define PHY_REMOTE_FAULT BIT(4)
-#define PHY_AUTO_NEG_CAPABLE BIT(3)
-#define PHY_LINK_STATUS BIT(2)
-#define PHY_JABBER_DETECT_NOT BIT(1)
-#define PHY_EXTENDED_CAPABILITY BIT(0)
-
-#define PHY_REG_ID_1 2
-#define PHY_REG_ID_2 3
-
-#define PHY_REG_AUTO_NEGOTIATION 4
-
-#define PHY_AUTO_NEG_NEXT_PAGE_NOT BIT(15)
-#define PHY_AUTO_NEG_REMOTE_FAULT_NOT BIT(13)
-#define PHY_AUTO_NEG_SYM_PAUSE BIT(10)
-#define PHY_AUTO_NEG_100BT4 BIT(9)
-#define PHY_AUTO_NEG_100BTX_FD BIT(8)
-#define PHY_AUTO_NEG_100BTX BIT(7)
-#define PHY_AUTO_NEG_10BT_FD BIT(6)
-#define PHY_AUTO_NEG_10BT BIT(5)
-#define PHY_AUTO_NEG_SELECTOR 0x001F
-#define PHY_AUTO_NEG_802_3 0x0001
-
-#define PHY_REG_REMOTE_CAPABILITY 5
-
-#define PHY_REMOTE_NEXT_PAGE_NOT BIT(15)
-#define PHY_REMOTE_ACKNOWLEDGE_NOT BIT(14)
-#define PHY_REMOTE_REMOTE_FAULT_NOT BIT(13)
-#define PHY_REMOTE_SYM_PAUSE BIT(10)
-#define PHY_REMOTE_100BTX_FD BIT(8)
-#define PHY_REMOTE_100BTX BIT(7)
-#define PHY_REMOTE_10BT_FD BIT(6)
-#define PHY_REMOTE_10BT BIT(5)
-#endif
-
#define KSZ8795_ID_HI 0x0022
#define KSZ8795_ID_LO 0x1550
#define KSZ8863_ID_LO 0x1430
diff --git a/drivers/net/ethernet/micrel/ksz884x.c b/drivers/net/ethernet/micrel/ksz884x.c
index 3532bfe936f6..7945eb5e2fe8 100644
--- a/drivers/net/ethernet/micrel/ksz884x.c
+++ b/drivers/net/ethernet/micrel/ksz884x.c
@@ -25,6 +25,7 @@
#include <linux/crc32.h>
#include <linux/sched.h>
#include <linux/slab.h>
+#include <linux/micrel_phy.h>
/* DMA Registers */
@@ -271,84 +272,15 @@
#define KS884X_PHY_CTRL_OFFSET 0x00
-/* Mode Control Register */
-#define PHY_REG_CTRL 0
-
-#define PHY_RESET 0x8000
-#define PHY_LOOPBACK 0x4000
-#define PHY_SPEED_100MBIT 0x2000
-#define PHY_AUTO_NEG_ENABLE 0x1000
-#define PHY_POWER_DOWN 0x0800
-#define PHY_MII_DISABLE 0x0400
-#define PHY_AUTO_NEG_RESTART 0x0200
-#define PHY_FULL_DUPLEX 0x0100
-#define PHY_COLLISION_TEST 0x0080
-#define PHY_HP_MDIX 0x0020
-#define PHY_FORCE_MDIX 0x0010
-#define PHY_AUTO_MDIX_DISABLE 0x0008
-#define PHY_REMOTE_FAULT_DISABLE 0x0004
-#define PHY_TRANSMIT_DISABLE 0x0002
-#define PHY_LED_DISABLE 0x0001
-
#define KS884X_PHY_STATUS_OFFSET 0x02
-/* Mode Status Register */
-#define PHY_REG_STATUS 1
-
-#define PHY_100BT4_CAPABLE 0x8000
-#define PHY_100BTX_FD_CAPABLE 0x4000
-#define PHY_100BTX_CAPABLE 0x2000
-#define PHY_10BT_FD_CAPABLE 0x1000
-#define PHY_10BT_CAPABLE 0x0800
-#define PHY_MII_SUPPRESS_CAPABLE 0x0040
-#define PHY_AUTO_NEG_ACKNOWLEDGE 0x0020
-#define PHY_REMOTE_FAULT 0x0010
-#define PHY_AUTO_NEG_CAPABLE 0x0008
-#define PHY_LINK_STATUS 0x0004
-#define PHY_JABBER_DETECT 0x0002
-#define PHY_EXTENDED_CAPABILITY 0x0001
-
#define KS884X_PHY_ID_1_OFFSET 0x04
#define KS884X_PHY_ID_2_OFFSET 0x06
-/* PHY Identifier Registers */
-#define PHY_REG_ID_1 2
-#define PHY_REG_ID_2 3
-
#define KS884X_PHY_AUTO_NEG_OFFSET 0x08
-/* Auto-Negotiation Advertisement Register */
-#define PHY_REG_AUTO_NEGOTIATION 4
-
-#define PHY_AUTO_NEG_NEXT_PAGE 0x8000
-#define PHY_AUTO_NEG_REMOTE_FAULT 0x2000
-/* Not supported. */
-#define PHY_AUTO_NEG_ASYM_PAUSE 0x0800
-#define PHY_AUTO_NEG_SYM_PAUSE 0x0400
-#define PHY_AUTO_NEG_100BT4 0x0200
-#define PHY_AUTO_NEG_100BTX_FD 0x0100
-#define PHY_AUTO_NEG_100BTX 0x0080
-#define PHY_AUTO_NEG_10BT_FD 0x0040
-#define PHY_AUTO_NEG_10BT 0x0020
-#define PHY_AUTO_NEG_SELECTOR 0x001F
-#define PHY_AUTO_NEG_802_3 0x0001
-
-#define PHY_AUTO_NEG_PAUSE (PHY_AUTO_NEG_SYM_PAUSE | PHY_AUTO_NEG_ASYM_PAUSE)
-
#define KS884X_PHY_REMOTE_CAP_OFFSET 0x0A
-/* Auto-Negotiation Link Partner Ability Register */
-#define PHY_REG_REMOTE_CAPABILITY 5
-
-#define PHY_REMOTE_NEXT_PAGE 0x8000
-#define PHY_REMOTE_ACKNOWLEDGE 0x4000
-#define PHY_REMOTE_REMOTE_FAULT 0x2000
-#define PHY_REMOTE_SYM_PAUSE 0x0400
-#define PHY_REMOTE_100BTX_FD 0x0100
-#define PHY_REMOTE_100BTX 0x0080
-#define PHY_REMOTE_10BT_FD 0x0040
-#define PHY_REMOTE_10BT 0x0020
-
/* P1VCT */
#define KS884X_P1VCT_P 0x04F0
#define KS884X_P1PHYCTRL_P 0x04F2
@@ -2886,15 +2818,6 @@ static void sw_block_addr(struct ksz_hw *hw)
}
}
-#define PHY_LINK_SUPPORT \
- (PHY_AUTO_NEG_ASYM_PAUSE | \
- PHY_AUTO_NEG_SYM_PAUSE | \
- PHY_AUTO_NEG_100BT4 | \
- PHY_AUTO_NEG_100BTX_FD | \
- PHY_AUTO_NEG_100BTX | \
- PHY_AUTO_NEG_10BT_FD | \
- PHY_AUTO_NEG_10BT)
-
static inline void hw_r_phy_ctrl(struct ksz_hw *hw, int phy, u16 *data)
{
*data = readw(hw->io + phy + KS884X_PHY_CTRL_OFFSET);
@@ -3238,16 +3161,18 @@ static void determine_flow_ctrl(struct ksz_hw *hw, struct ksz_port *port,
rx = tx = 0;
if (port->force_link)
rx = tx = 1;
- if (remote & PHY_AUTO_NEG_SYM_PAUSE) {
- if (local & PHY_AUTO_NEG_SYM_PAUSE) {
+ if (remote & LPA_PAUSE_CAP) {
+ if (local & ADVERTISE_PAUSE_CAP) {
rx = tx = 1;
- } else if ((remote & PHY_AUTO_NEG_ASYM_PAUSE) &&
- (local & PHY_AUTO_NEG_PAUSE) ==
- PHY_AUTO_NEG_ASYM_PAUSE) {
+ } else if ((remote & LPA_PAUSE_ASYM) &&
+ (local &
+ (ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM)) ==
+ ADVERTISE_PAUSE_ASYM) {
tx = 1;
}
- } else if (remote & PHY_AUTO_NEG_ASYM_PAUSE) {
- if ((local & PHY_AUTO_NEG_PAUSE) == PHY_AUTO_NEG_PAUSE)
+ } else if (remote & LPA_PAUSE_ASYM) {
+ if ((local & (ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM))
+ == (ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM))
rx = 1;
}
if (!hw->ksz_switch)
@@ -3428,16 +3353,16 @@ static void port_force_link_speed(struct ksz_port *port)
phy = KS884X_PHY_1_CTRL_OFFSET + p * PHY_CTRL_INTERVAL;
hw_r_phy_ctrl(hw, phy, &data);
- data &= ~PHY_AUTO_NEG_ENABLE;
+ data &= ~BMCR_ANENABLE;
if (10 == port->speed)
- data &= ~PHY_SPEED_100MBIT;
+ data &= ~BMCR_SPEED100;
else if (100 == port->speed)
- data |= PHY_SPEED_100MBIT;
+ data |= BMCR_SPEED100;
if (1 == port->duplex)
- data &= ~PHY_FULL_DUPLEX;
+ data &= ~BMCR_FULLDPLX;
else if (2 == port->duplex)
- data |= PHY_FULL_DUPLEX;
+ data |= BMCR_FULLDPLX;
hw_w_phy_ctrl(hw, phy, data);
}
}
diff --git a/include/linux/micrel_phy.h b/include/linux/micrel_phy.h
index 416ee6dd2574..b03e2afcb53f 100644
--- a/include/linux/micrel_phy.h
+++ b/include/linux/micrel_phy.h
@@ -45,4 +45,17 @@
#define MICREL_KSZ9021_RGMII_CLK_CTRL_PAD_SCEW 0x104
#define MICREL_KSZ9021_RGMII_RX_DATA_PAD_SCEW 0x105
+/* Device specific MII_BMCR (Reg 0) bits */
+/* 1 = HP Auto MDI/MDI-X mode, 0 = Microchip Auto MDI/MDI-X mode */
+#define KSZ886X_BMCR_HP_MDIX BIT(5)
+/* 1 = Force MDI (transmit on RXP/RXM pins), 0 = Normal operation
+ * (transmit on TXP/TXM pins)
+ */
+#define KSZ886X_BMCR_FORCE_MDI BIT(4)
+/* 1 = Disable auto MDI-X */
+#define KSZ886X_BMCR_DISABLE_AUTO_MDIX BIT(3)
+#define KSZ886X_BMCR_DISABLE_FAR_END_FAULT BIT(2)
+#define KSZ886X_BMCR_DISABLE_TRANSMIT BIT(1)
+#define KSZ886X_BMCR_DISABLE_LED BIT(0)
+
#endif /* _MICREL_PHY_H */
--
2.29.2
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH net-next v5 2/8] net: dsa: microchip: ksz8795: add phylink support
2021-06-14 4:31 [PATCH net-next v5 0/8] provide cable test support for the ksz886x switch Oleksij Rempel
2021-06-14 4:31 ` [PATCH net-next v5 1/8] net: phy: micrel: move phy reg offsets to common header Oleksij Rempel
@ 2021-06-14 4:31 ` Oleksij Rempel
2021-06-14 4:31 ` [PATCH net-next v5 3/8] net: phy: micrel: use consistent alignments Oleksij Rempel
` (6 subsequent siblings)
8 siblings, 0 replies; 10+ messages in thread
From: Oleksij Rempel @ 2021-06-14 4:31 UTC (permalink / raw)
To: Woojung Huh, UNGLinuxDriver, Andrew Lunn, Florian Fainelli,
Vivien Didelot, Vladimir Oltean, David S. Miller, Jakub Kicinski
Cc: Michael Grzeschik, Oleksij Rempel, kernel, netdev, linux-kernel,
Russell King
From: Michael Grzeschik <m.grzeschik@pengutronix.de>
This patch adds the phylink support to the ksz8795 driver to provide
configuration exceptions on quirky KSZ8863 and KSZ8873 ports.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/dsa/microchip/ksz8795.c | 55 +++++++++++++++++++++++++++++
1 file changed, 55 insertions(+)
diff --git a/drivers/net/dsa/microchip/ksz8795.c b/drivers/net/dsa/microchip/ksz8795.c
index ba065003623f..cfa2a5000cd3 100644
--- a/drivers/net/dsa/microchip/ksz8795.c
+++ b/drivers/net/dsa/microchip/ksz8795.c
@@ -18,6 +18,7 @@
#include <linux/micrel_phy.h>
#include <net/dsa.h>
#include <net/switchdev.h>
+#include <linux/phylink.h>
#include "ksz_common.h"
#include "ksz8795_reg.h"
@@ -1420,11 +1421,65 @@ static int ksz8_setup(struct dsa_switch *ds)
return 0;
}
+static void ksz8_validate(struct dsa_switch *ds, int port,
+ unsigned long *supported,
+ struct phylink_link_state *state)
+{
+ __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
+ struct ksz_device *dev = ds->priv;
+
+ if (port == dev->cpu_port) {
+ if (state->interface != PHY_INTERFACE_MODE_RMII &&
+ state->interface != PHY_INTERFACE_MODE_MII &&
+ state->interface != PHY_INTERFACE_MODE_NA)
+ goto unsupported;
+ } else {
+ if (state->interface != PHY_INTERFACE_MODE_INTERNAL &&
+ state->interface != PHY_INTERFACE_MODE_NA)
+ goto unsupported;
+ }
+
+ /* Allow all the expected bits */
+ phylink_set_port_modes(mask);
+ phylink_set(mask, Autoneg);
+
+ /* Silicon Errata Sheet (DS80000830A):
+ * "Port 1 does not respond to received flow control PAUSE frames"
+ * So, disable Pause support on "Port 1" (port == 0) for all ksz88x3
+ * switches.
+ */
+ if (!ksz_is_ksz88x3(dev) || port)
+ phylink_set(mask, Pause);
+
+ /* Asym pause is not supported on KSZ8863 and KSZ8873 */
+ if (!ksz_is_ksz88x3(dev))
+ phylink_set(mask, Asym_Pause);
+
+ /* 10M and 100M are only supported */
+ phylink_set(mask, 10baseT_Half);
+ phylink_set(mask, 10baseT_Full);
+ phylink_set(mask, 100baseT_Half);
+ phylink_set(mask, 100baseT_Full);
+
+ bitmap_and(supported, supported, mask,
+ __ETHTOOL_LINK_MODE_MASK_NBITS);
+ bitmap_and(state->advertising, state->advertising, mask,
+ __ETHTOOL_LINK_MODE_MASK_NBITS);
+
+ return;
+
+unsupported:
+ bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
+ dev_err(ds->dev, "Unsupported interface: %s, port: %d\n",
+ phy_modes(state->interface), port);
+}
+
static const struct dsa_switch_ops ksz8_switch_ops = {
.get_tag_protocol = ksz8_get_tag_protocol,
.setup = ksz8_setup,
.phy_read = ksz_phy_read16,
.phy_write = ksz_phy_write16,
+ .phylink_validate = ksz8_validate,
.phylink_mac_link_down = ksz_mac_link_down,
.port_enable = ksz_enable_port,
.get_strings = ksz8_get_strings,
--
2.29.2
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH net-next v5 3/8] net: phy: micrel: use consistent alignments
2021-06-14 4:31 [PATCH net-next v5 0/8] provide cable test support for the ksz886x switch Oleksij Rempel
2021-06-14 4:31 ` [PATCH net-next v5 1/8] net: phy: micrel: move phy reg offsets to common header Oleksij Rempel
2021-06-14 4:31 ` [PATCH net-next v5 2/8] net: dsa: microchip: ksz8795: add phylink support Oleksij Rempel
@ 2021-06-14 4:31 ` Oleksij Rempel
2021-06-14 4:31 ` [PATCH net-next v5 4/8] net: phy/dsa micrel/ksz886x add MDI-X support Oleksij Rempel
` (5 subsequent siblings)
8 siblings, 0 replies; 10+ messages in thread
From: Oleksij Rempel @ 2021-06-14 4:31 UTC (permalink / raw)
To: Woojung Huh, UNGLinuxDriver, Andrew Lunn, Florian Fainelli,
Vivien Didelot, Vladimir Oltean, David S. Miller, Jakub Kicinski
Cc: Oleksij Rempel, kernel, netdev, linux-kernel, Russell King,
Michael Grzeschik
This patch changes the alignments to one space between "#define" and the
macro.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/phy/micrel.c | 44 ++++++++++++++++++++--------------------
1 file changed, 22 insertions(+), 22 deletions(-)
diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
index a14a00328fa3..77640b990977 100644
--- a/drivers/net/phy/micrel.c
+++ b/drivers/net/phy/micrel.c
@@ -38,42 +38,42 @@
/* general Interrupt control/status reg in vendor specific block. */
#define MII_KSZPHY_INTCS 0x1B
-#define KSZPHY_INTCS_JABBER BIT(15)
-#define KSZPHY_INTCS_RECEIVE_ERR BIT(14)
-#define KSZPHY_INTCS_PAGE_RECEIVE BIT(13)
-#define KSZPHY_INTCS_PARELLEL BIT(12)
-#define KSZPHY_INTCS_LINK_PARTNER_ACK BIT(11)
-#define KSZPHY_INTCS_LINK_DOWN BIT(10)
-#define KSZPHY_INTCS_REMOTE_FAULT BIT(9)
-#define KSZPHY_INTCS_LINK_UP BIT(8)
-#define KSZPHY_INTCS_ALL (KSZPHY_INTCS_LINK_UP |\
+#define KSZPHY_INTCS_JABBER BIT(15)
+#define KSZPHY_INTCS_RECEIVE_ERR BIT(14)
+#define KSZPHY_INTCS_PAGE_RECEIVE BIT(13)
+#define KSZPHY_INTCS_PARELLEL BIT(12)
+#define KSZPHY_INTCS_LINK_PARTNER_ACK BIT(11)
+#define KSZPHY_INTCS_LINK_DOWN BIT(10)
+#define KSZPHY_INTCS_REMOTE_FAULT BIT(9)
+#define KSZPHY_INTCS_LINK_UP BIT(8)
+#define KSZPHY_INTCS_ALL (KSZPHY_INTCS_LINK_UP |\
KSZPHY_INTCS_LINK_DOWN)
-#define KSZPHY_INTCS_LINK_DOWN_STATUS BIT(2)
-#define KSZPHY_INTCS_LINK_UP_STATUS BIT(0)
-#define KSZPHY_INTCS_STATUS (KSZPHY_INTCS_LINK_DOWN_STATUS |\
+#define KSZPHY_INTCS_LINK_DOWN_STATUS BIT(2)
+#define KSZPHY_INTCS_LINK_UP_STATUS BIT(0)
+#define KSZPHY_INTCS_STATUS (KSZPHY_INTCS_LINK_DOWN_STATUS |\
KSZPHY_INTCS_LINK_UP_STATUS)
/* PHY Control 1 */
-#define MII_KSZPHY_CTRL_1 0x1e
+#define MII_KSZPHY_CTRL_1 0x1e
/* PHY Control 2 / PHY Control (if no PHY Control 1) */
-#define MII_KSZPHY_CTRL_2 0x1f
-#define MII_KSZPHY_CTRL MII_KSZPHY_CTRL_2
+#define MII_KSZPHY_CTRL_2 0x1f
+#define MII_KSZPHY_CTRL MII_KSZPHY_CTRL_2
/* bitmap of PHY register to set interrupt mode */
#define KSZPHY_CTRL_INT_ACTIVE_HIGH BIT(9)
#define KSZPHY_RMII_REF_CLK_SEL BIT(7)
/* Write/read to/from extended registers */
-#define MII_KSZPHY_EXTREG 0x0b
-#define KSZPHY_EXTREG_WRITE 0x8000
+#define MII_KSZPHY_EXTREG 0x0b
+#define KSZPHY_EXTREG_WRITE 0x8000
-#define MII_KSZPHY_EXTREG_WRITE 0x0c
-#define MII_KSZPHY_EXTREG_READ 0x0d
+#define MII_KSZPHY_EXTREG_WRITE 0x0c
+#define MII_KSZPHY_EXTREG_READ 0x0d
/* Extended registers */
-#define MII_KSZPHY_CLK_CONTROL_PAD_SKEW 0x104
-#define MII_KSZPHY_RX_DATA_PAD_SKEW 0x105
-#define MII_KSZPHY_TX_DATA_PAD_SKEW 0x106
+#define MII_KSZPHY_CLK_CONTROL_PAD_SKEW 0x104
+#define MII_KSZPHY_RX_DATA_PAD_SKEW 0x105
+#define MII_KSZPHY_TX_DATA_PAD_SKEW 0x106
#define PS_TO_REG 200
--
2.29.2
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH net-next v5 4/8] net: phy/dsa micrel/ksz886x add MDI-X support
2021-06-14 4:31 [PATCH net-next v5 0/8] provide cable test support for the ksz886x switch Oleksij Rempel
` (2 preceding siblings ...)
2021-06-14 4:31 ` [PATCH net-next v5 3/8] net: phy: micrel: use consistent alignments Oleksij Rempel
@ 2021-06-14 4:31 ` Oleksij Rempel
2021-06-14 4:31 ` [PATCH net-next v5 5/8] net: phy: micrel: ksz8081 " Oleksij Rempel
` (4 subsequent siblings)
8 siblings, 0 replies; 10+ messages in thread
From: Oleksij Rempel @ 2021-06-14 4:31 UTC (permalink / raw)
To: Woojung Huh, UNGLinuxDriver, Andrew Lunn, Florian Fainelli,
Vivien Didelot, Vladimir Oltean, David S. Miller, Jakub Kicinski
Cc: Oleksij Rempel, kernel, netdev, linux-kernel, Russell King,
Michael Grzeschik
Add support for MDI-X status and configuration
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/dsa/microchip/ksz8795.c | 5 ++
drivers/net/phy/micrel.c | 88 +++++++++++++++++++++++++++++
include/linux/micrel_phy.h | 2 +
3 files changed, 95 insertions(+)
diff --git a/drivers/net/dsa/microchip/ksz8795.c b/drivers/net/dsa/microchip/ksz8795.c
index cfa2a5000cd3..690304c87b02 100644
--- a/drivers/net/dsa/microchip/ksz8795.c
+++ b/drivers/net/dsa/microchip/ksz8795.c
@@ -816,6 +816,11 @@ static void ksz8_r_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 *val)
if (data & ~LPA_SLCT)
data |= LPA_LPACK;
break;
+ case PHY_REG_PHY_CTRL:
+ ksz_pread8(dev, p, regs[P_LINK_STATUS], &link);
+ if (link & PORT_MDIX_STATUS)
+ data |= KSZ886X_CTRL_MDIX_STAT;
+ break;
default:
processed = false;
break;
diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
index 77640b990977..75d230da9738 100644
--- a/drivers/net/phy/micrel.c
+++ b/drivers/net/phy/micrel.c
@@ -1048,6 +1048,92 @@ static int ksz8873mll_config_aneg(struct phy_device *phydev)
return 0;
}
+static int ksz886x_config_mdix(struct phy_device *phydev, u8 ctrl)
+{
+ u16 val;
+
+ switch (ctrl) {
+ case ETH_TP_MDI:
+ val = KSZ886X_BMCR_DISABLE_AUTO_MDIX;
+ break;
+ case ETH_TP_MDI_X:
+ /* Note: The naming of the bit KSZ886X_BMCR_FORCE_MDI is bit
+ * counter intuitive, the "-X" in "1 = Force MDI" in the data
+ * sheet seems to be missing:
+ * 1 = Force MDI (sic!) (transmit on RX+/RX- pins)
+ * 0 = Normal operation (transmit on TX+/TX- pins)
+ */
+ val = KSZ886X_BMCR_DISABLE_AUTO_MDIX | KSZ886X_BMCR_FORCE_MDI;
+ break;
+ case ETH_TP_MDI_AUTO:
+ val = 0;
+ break;
+ default:
+ return 0;
+ }
+
+ return phy_modify(phydev, MII_BMCR,
+ KSZ886X_BMCR_HP_MDIX | KSZ886X_BMCR_FORCE_MDI |
+ KSZ886X_BMCR_DISABLE_AUTO_MDIX,
+ KSZ886X_BMCR_HP_MDIX | val);
+}
+
+static int ksz886x_config_aneg(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = genphy_config_aneg(phydev);
+ if (ret)
+ return ret;
+
+ /* The MDI-X configuration is automatically changed by the PHY after
+ * switching from autoneg off to on. So, take MDI-X configuration under
+ * own control and set it after autoneg configuration was done.
+ */
+ return ksz886x_config_mdix(phydev, phydev->mdix_ctrl);
+}
+
+static int ksz886x_mdix_update(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = phy_read(phydev, MII_BMCR);
+ if (ret < 0)
+ return ret;
+
+ if (ret & KSZ886X_BMCR_DISABLE_AUTO_MDIX) {
+ if (ret & KSZ886X_BMCR_FORCE_MDI)
+ phydev->mdix_ctrl = ETH_TP_MDI_X;
+ else
+ phydev->mdix_ctrl = ETH_TP_MDI;
+ } else {
+ phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
+ }
+
+ ret = phy_read(phydev, MII_KSZPHY_CTRL);
+ if (ret < 0)
+ return ret;
+
+ /* Same reverse logic as KSZ886X_BMCR_FORCE_MDI */
+ if (ret & KSZ886X_CTRL_MDIX_STAT)
+ phydev->mdix = ETH_TP_MDI_X;
+ else
+ phydev->mdix = ETH_TP_MDI;
+
+ return 0;
+}
+
+static int ksz886x_read_status(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = ksz886x_mdix_update(phydev);
+ if (ret < 0)
+ return ret;
+
+ return genphy_read_status(phydev);
+}
+
static int kszphy_get_sset_count(struct phy_device *phydev)
{
return ARRAY_SIZE(kszphy_hw_stats);
@@ -1400,6 +1486,8 @@ static struct phy_driver ksphy_driver[] = {
.name = "Micrel KSZ8851 Ethernet MAC or KSZ886X Switch",
/* PHY_BASIC_FEATURES */
.config_init = kszphy_config_init,
+ .config_aneg = ksz886x_config_aneg,
+ .read_status = ksz886x_read_status,
.suspend = genphy_suspend,
.resume = genphy_resume,
}, {
diff --git a/include/linux/micrel_phy.h b/include/linux/micrel_phy.h
index b03e2afcb53f..58370abd9f4f 100644
--- a/include/linux/micrel_phy.h
+++ b/include/linux/micrel_phy.h
@@ -58,4 +58,6 @@
#define KSZ886X_BMCR_DISABLE_TRANSMIT BIT(1)
#define KSZ886X_BMCR_DISABLE_LED BIT(0)
+#define KSZ886X_CTRL_MDIX_STAT BIT(4)
+
#endif /* _MICREL_PHY_H */
--
2.29.2
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH net-next v5 5/8] net: phy: micrel: ksz8081 add MDI-X support
2021-06-14 4:31 [PATCH net-next v5 0/8] provide cable test support for the ksz886x switch Oleksij Rempel
` (3 preceding siblings ...)
2021-06-14 4:31 ` [PATCH net-next v5 4/8] net: phy/dsa micrel/ksz886x add MDI-X support Oleksij Rempel
@ 2021-06-14 4:31 ` Oleksij Rempel
2021-06-14 4:31 ` [PATCH net-next v5 6/8] net: dsa: microchip: ksz8795: add LINK_MD register support Oleksij Rempel
` (3 subsequent siblings)
8 siblings, 0 replies; 10+ messages in thread
From: Oleksij Rempel @ 2021-06-14 4:31 UTC (permalink / raw)
To: Woojung Huh, UNGLinuxDriver, Andrew Lunn, Florian Fainelli,
Vivien Didelot, Vladimir Oltean, David S. Miller, Jakub Kicinski
Cc: Oleksij Rempel, kernel, netdev, linux-kernel, Russell King,
Michael Grzeschik
Add support for MDI-X status and configuration
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/phy/micrel.c | 89 ++++++++++++++++++++++++++++++++++++++++
1 file changed, 89 insertions(+)
diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
index 75d230da9738..6b900dd87e28 100644
--- a/drivers/net/phy/micrel.c
+++ b/drivers/net/phy/micrel.c
@@ -55,11 +55,17 @@
/* PHY Control 1 */
#define MII_KSZPHY_CTRL_1 0x1e
+#define KSZ8081_CTRL1_MDIX_STAT BIT(4)
/* PHY Control 2 / PHY Control (if no PHY Control 1) */
#define MII_KSZPHY_CTRL_2 0x1f
#define MII_KSZPHY_CTRL MII_KSZPHY_CTRL_2
/* bitmap of PHY register to set interrupt mode */
+#define KSZ8081_CTRL2_HP_MDIX BIT(15)
+#define KSZ8081_CTRL2_MDI_MDI_X_SELECT BIT(14)
+#define KSZ8081_CTRL2_DISABLE_AUTO_MDIX BIT(13)
+#define KSZ8081_CTRL2_FORCE_LINK BIT(11)
+#define KSZ8081_CTRL2_POWER_SAVING BIT(10)
#define KSZPHY_CTRL_INT_ACTIVE_HIGH BIT(9)
#define KSZPHY_RMII_REF_CLK_SEL BIT(7)
@@ -422,6 +428,87 @@ static int ksz8081_config_init(struct phy_device *phydev)
return kszphy_config_init(phydev);
}
+static int ksz8081_config_mdix(struct phy_device *phydev, u8 ctrl)
+{
+ u16 val;
+
+ switch (ctrl) {
+ case ETH_TP_MDI:
+ val = KSZ8081_CTRL2_DISABLE_AUTO_MDIX;
+ break;
+ case ETH_TP_MDI_X:
+ val = KSZ8081_CTRL2_DISABLE_AUTO_MDIX |
+ KSZ8081_CTRL2_MDI_MDI_X_SELECT;
+ break;
+ case ETH_TP_MDI_AUTO:
+ val = 0;
+ break;
+ default:
+ return 0;
+ }
+
+ return phy_modify(phydev, MII_KSZPHY_CTRL_2,
+ KSZ8081_CTRL2_HP_MDIX |
+ KSZ8081_CTRL2_MDI_MDI_X_SELECT |
+ KSZ8081_CTRL2_DISABLE_AUTO_MDIX,
+ KSZ8081_CTRL2_HP_MDIX | val);
+}
+
+static int ksz8081_config_aneg(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = genphy_config_aneg(phydev);
+ if (ret)
+ return ret;
+
+ /* The MDI-X configuration is automatically changed by the PHY after
+ * switching from autoneg off to on. So, take MDI-X configuration under
+ * own control and set it after autoneg configuration was done.
+ */
+ return ksz8081_config_mdix(phydev, phydev->mdix_ctrl);
+}
+
+static int ksz8081_mdix_update(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = phy_read(phydev, MII_KSZPHY_CTRL_2);
+ if (ret < 0)
+ return ret;
+
+ if (ret & KSZ8081_CTRL2_DISABLE_AUTO_MDIX) {
+ if (ret & KSZ8081_CTRL2_MDI_MDI_X_SELECT)
+ phydev->mdix_ctrl = ETH_TP_MDI_X;
+ else
+ phydev->mdix_ctrl = ETH_TP_MDI;
+ } else {
+ phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
+ }
+
+ ret = phy_read(phydev, MII_KSZPHY_CTRL_1);
+ if (ret < 0)
+ return ret;
+
+ if (ret & KSZ8081_CTRL1_MDIX_STAT)
+ phydev->mdix = ETH_TP_MDI;
+ else
+ phydev->mdix = ETH_TP_MDI_X;
+
+ return 0;
+}
+
+static int ksz8081_read_status(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = ksz8081_mdix_update(phydev);
+ if (ret < 0)
+ return ret;
+
+ return genphy_read_status(phydev);
+}
+
static int ksz8061_config_init(struct phy_device *phydev)
{
int ret;
@@ -1390,6 +1477,8 @@ static struct phy_driver ksphy_driver[] = {
.probe = kszphy_probe,
.config_init = ksz8081_config_init,
.soft_reset = genphy_soft_reset,
+ .config_aneg = ksz8081_config_aneg,
+ .read_status = ksz8081_read_status,
.config_intr = kszphy_config_intr,
.handle_interrupt = kszphy_handle_interrupt,
.get_sset_count = kszphy_get_sset_count,
--
2.29.2
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH net-next v5 6/8] net: dsa: microchip: ksz8795: add LINK_MD register support
2021-06-14 4:31 [PATCH net-next v5 0/8] provide cable test support for the ksz886x switch Oleksij Rempel
` (4 preceding siblings ...)
2021-06-14 4:31 ` [PATCH net-next v5 5/8] net: phy: micrel: ksz8081 " Oleksij Rempel
@ 2021-06-14 4:31 ` Oleksij Rempel
2021-06-14 4:31 ` [PATCH net-next v5 7/8] net: dsa: dsa_slave_phy_connect(): extend phy's flags with port specific phy flags Oleksij Rempel
` (2 subsequent siblings)
8 siblings, 0 replies; 10+ messages in thread
From: Oleksij Rempel @ 2021-06-14 4:31 UTC (permalink / raw)
To: Woojung Huh, UNGLinuxDriver, Andrew Lunn, Florian Fainelli,
Vivien Didelot, Vladimir Oltean, David S. Miller, Jakub Kicinski
Cc: Oleksij Rempel, Oleksij Rempel, kernel, netdev, linux-kernel,
Russell King, Michael Grzeschik
From: Oleksij Rempel <linux@rempel-privat.de>
Add mapping for LINK_MD register to enable cable testing functionality.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/dsa/microchip/ksz8795.c | 22 ++++++++++++++++++++++
drivers/net/dsa/microchip/ksz8795_reg.h | 5 +++--
2 files changed, 25 insertions(+), 2 deletions(-)
diff --git a/drivers/net/dsa/microchip/ksz8795.c b/drivers/net/dsa/microchip/ksz8795.c
index 690304c87b02..e1731ae4497d 100644
--- a/drivers/net/dsa/microchip/ksz8795.c
+++ b/drivers/net/dsa/microchip/ksz8795.c
@@ -6,6 +6,7 @@
* Tristram Ha <Tristram.Ha@microchip.com>
*/
+#include <linux/bitfield.h>
#include <linux/delay.h>
#include <linux/export.h>
#include <linux/gpio.h>
@@ -729,6 +730,7 @@ static void ksz8_r_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 *val)
u8 restart, speed, ctrl, link;
const u8 *regs = ksz8->regs;
int processed = true;
+ u8 val1, val2;
u16 data = 0;
u8 p = phy;
@@ -816,6 +818,22 @@ static void ksz8_r_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 *val)
if (data & ~LPA_SLCT)
data |= LPA_LPACK;
break;
+ case PHY_REG_LINK_MD:
+ ksz_pread8(dev, p, REG_PORT_LINK_MD_CTRL, &val1);
+ ksz_pread8(dev, p, REG_PORT_LINK_MD_RESULT, &val2);
+ if (val1 & PORT_START_CABLE_DIAG)
+ data |= PHY_START_CABLE_DIAG;
+
+ if (val1 & PORT_CABLE_10M_SHORT)
+ data |= PHY_CABLE_10M_SHORT;
+
+ data |= FIELD_PREP(PHY_CABLE_DIAG_RESULT_M,
+ FIELD_GET(PORT_CABLE_DIAG_RESULT_M, val1));
+
+ data |= FIELD_PREP(PHY_CABLE_FAULT_COUNTER_M,
+ (FIELD_GET(PORT_CABLE_FAULT_COUNTER_H, val1) << 8) |
+ FIELD_GET(PORT_CABLE_FAULT_COUNTER_L, val2));
+ break;
case PHY_REG_PHY_CTRL:
ksz_pread8(dev, p, regs[P_LINK_STATUS], &link);
if (link & PORT_MDIX_STATUS)
@@ -932,6 +950,10 @@ static void ksz8_w_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 val)
if (data != ctrl)
ksz_pwrite8(dev, p, regs[P_LOCAL_CTRL], data);
break;
+ case PHY_REG_LINK_MD:
+ if (val & PHY_START_CABLE_DIAG)
+ ksz_port_cfg(dev, p, REG_PORT_LINK_MD_CTRL, PORT_START_CABLE_DIAG, true);
+ break;
default:
break;
}
diff --git a/drivers/net/dsa/microchip/ksz8795_reg.h b/drivers/net/dsa/microchip/ksz8795_reg.h
index f925ddee5238..a32355624f31 100644
--- a/drivers/net/dsa/microchip/ksz8795_reg.h
+++ b/drivers/net/dsa/microchip/ksz8795_reg.h
@@ -249,7 +249,7 @@
#define REG_PORT_4_LINK_MD_CTRL 0x4A
#define PORT_CABLE_10M_SHORT BIT(7)
-#define PORT_CABLE_DIAG_RESULT_M 0x3
+#define PORT_CABLE_DIAG_RESULT_M GENMASK(6, 5)
#define PORT_CABLE_DIAG_RESULT_S 5
#define PORT_CABLE_STAT_NORMAL 0
#define PORT_CABLE_STAT_OPEN 1
@@ -753,13 +753,14 @@
#define PHY_REG_LINK_MD 0x1D
#define PHY_START_CABLE_DIAG BIT(15)
+#define PHY_CABLE_DIAG_RESULT_M GENMASK(14, 13)
#define PHY_CABLE_DIAG_RESULT 0x6000
#define PHY_CABLE_STAT_NORMAL 0x0000
#define PHY_CABLE_STAT_OPEN 0x2000
#define PHY_CABLE_STAT_SHORT 0x4000
#define PHY_CABLE_STAT_FAILED 0x6000
#define PHY_CABLE_10M_SHORT BIT(12)
-#define PHY_CABLE_FAULT_COUNTER 0x01FF
+#define PHY_CABLE_FAULT_COUNTER_M GENMASK(8, 0)
#define PHY_REG_PHY_CTRL 0x1F
--
2.29.2
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH net-next v5 7/8] net: dsa: dsa_slave_phy_connect(): extend phy's flags with port specific phy flags
2021-06-14 4:31 [PATCH net-next v5 0/8] provide cable test support for the ksz886x switch Oleksij Rempel
` (5 preceding siblings ...)
2021-06-14 4:31 ` [PATCH net-next v5 6/8] net: dsa: microchip: ksz8795: add LINK_MD register support Oleksij Rempel
@ 2021-06-14 4:31 ` Oleksij Rempel
2021-06-14 4:31 ` [PATCH net-next v5 8/8] net: phy: micrel: ksz886x/ksz8081: add cabletest support Oleksij Rempel
2021-06-14 20:00 ` [PATCH net-next v5 0/8] provide cable test support for the ksz886x switch patchwork-bot+netdevbpf
8 siblings, 0 replies; 10+ messages in thread
From: Oleksij Rempel @ 2021-06-14 4:31 UTC (permalink / raw)
To: Woojung Huh, UNGLinuxDriver, Andrew Lunn, Florian Fainelli,
Vivien Didelot, Vladimir Oltean, David S. Miller, Jakub Kicinski
Cc: Oleksij Rempel, kernel, netdev, linux-kernel, Russell King,
Michael Grzeschik
The current get_phy_flags() is only processed when we connect to a PHY
via a designed phy-handle property via phylink_of_phy_connect(), but if
we fallback on the internal MDIO bus created by a switch and take the
dsa_slave_phy_connect() path then we would not be processing that flag
and using it at PHY connection time.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
net/dsa/slave.c | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
diff --git a/net/dsa/slave.c b/net/dsa/slave.c
index d4756b920108..915c7cab7900 100644
--- a/net/dsa/slave.c
+++ b/net/dsa/slave.c
@@ -1749,7 +1749,8 @@ static void dsa_slave_phylink_fixed_state(struct phylink_config *config,
}
/* slave device setup *******************************************************/
-static int dsa_slave_phy_connect(struct net_device *slave_dev, int addr)
+static int dsa_slave_phy_connect(struct net_device *slave_dev, int addr,
+ u32 flags)
{
struct dsa_port *dp = dsa_slave_to_port(slave_dev);
struct dsa_switch *ds = dp->ds;
@@ -1760,6 +1761,8 @@ static int dsa_slave_phy_connect(struct net_device *slave_dev, int addr)
return -ENODEV;
}
+ slave_dev->phydev->dev_flags |= flags;
+
return phylink_connect_phy(dp->pl, slave_dev->phydev);
}
@@ -1804,7 +1807,7 @@ static int dsa_slave_phy_setup(struct net_device *slave_dev)
/* We could not connect to a designated PHY or SFP, so try to
* use the switch internal MDIO bus instead
*/
- ret = dsa_slave_phy_connect(slave_dev, dp->index);
+ ret = dsa_slave_phy_connect(slave_dev, dp->index, phy_flags);
if (ret) {
netdev_err(slave_dev,
"failed to connect to port %d: %d\n",
--
2.29.2
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH net-next v5 8/8] net: phy: micrel: ksz886x/ksz8081: add cabletest support
2021-06-14 4:31 [PATCH net-next v5 0/8] provide cable test support for the ksz886x switch Oleksij Rempel
` (6 preceding siblings ...)
2021-06-14 4:31 ` [PATCH net-next v5 7/8] net: dsa: dsa_slave_phy_connect(): extend phy's flags with port specific phy flags Oleksij Rempel
@ 2021-06-14 4:31 ` Oleksij Rempel
2021-06-14 20:00 ` [PATCH net-next v5 0/8] provide cable test support for the ksz886x switch patchwork-bot+netdevbpf
8 siblings, 0 replies; 10+ messages in thread
From: Oleksij Rempel @ 2021-06-14 4:31 UTC (permalink / raw)
To: Woojung Huh, UNGLinuxDriver, Andrew Lunn, Florian Fainelli,
Vivien Didelot, Vladimir Oltean, David S. Miller, Jakub Kicinski
Cc: Oleksij Rempel, kernel, netdev, linux-kernel, Russell King,
Michael Grzeschik
This patch support for cable test for the ksz886x switches and the
ksz8081 PHY.
The patch was tested on a KSZ8873RLL switch with following results:
- port 1:
- provides invalid values, thus return -ENOTSUPP
(Errata: DS80000830A: "LinkMD does not work on Port 1",
http://ww1.microchip.com/downloads/en/DeviceDoc/KSZ8873-Errata-DS80000830A.pdf)
- port 2:
- can detect distance
- can detect open on each wire of pair A (wire 1 and 2)
- can detect open only on one wire of pair B (only wire 3)
- can detect short between wires of a pair (wires 1 + 2 or 3 + 6)
- short between pairs is detected as open.
For example short between wires 2 + 3 is detected as open.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
drivers/net/dsa/microchip/ksz8795.c | 13 ++
drivers/net/phy/micrel.c | 180 ++++++++++++++++++++++++++++
include/linux/micrel_phy.h | 1 +
3 files changed, 194 insertions(+)
diff --git a/drivers/net/dsa/microchip/ksz8795.c b/drivers/net/dsa/microchip/ksz8795.c
index e1731ae4497d..560f6843bb65 100644
--- a/drivers/net/dsa/microchip/ksz8795.c
+++ b/drivers/net/dsa/microchip/ksz8795.c
@@ -970,6 +970,18 @@ static enum dsa_tag_protocol ksz8_get_tag_protocol(struct dsa_switch *ds,
DSA_TAG_PROTO_KSZ9893 : DSA_TAG_PROTO_KSZ8795;
}
+static u32 ksz8_sw_get_phy_flags(struct dsa_switch *ds, int port)
+{
+ /* Silicon Errata Sheet (DS80000830A):
+ * Port 1 does not work with LinkMD Cable-Testing.
+ * Port 1 does not respond to received PAUSE control frames.
+ */
+ if (!port)
+ return MICREL_KSZ8_P1_ERRATA;
+
+ return 0;
+}
+
static void ksz8_get_strings(struct dsa_switch *ds, int port,
u32 stringset, uint8_t *buf)
{
@@ -1503,6 +1515,7 @@ static void ksz8_validate(struct dsa_switch *ds, int port,
static const struct dsa_switch_ops ksz8_switch_ops = {
.get_tag_protocol = ksz8_get_tag_protocol,
+ .get_phy_flags = ksz8_sw_get_phy_flags,
.setup = ksz8_setup,
.phy_read = ksz_phy_read16,
.phy_write = ksz_phy_write16,
diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
index 6b900dd87e28..23f2e49ac7ab 100644
--- a/drivers/net/phy/micrel.c
+++ b/drivers/net/phy/micrel.c
@@ -20,6 +20,7 @@
*/
#include <linux/bitfield.h>
+#include <linux/ethtool_netlink.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/phy.h>
@@ -53,6 +54,18 @@
#define KSZPHY_INTCS_STATUS (KSZPHY_INTCS_LINK_DOWN_STATUS |\
KSZPHY_INTCS_LINK_UP_STATUS)
+/* LinkMD Control/Status */
+#define KSZ8081_LMD 0x1d
+#define KSZ8081_LMD_ENABLE_TEST BIT(15)
+#define KSZ8081_LMD_STAT_NORMAL 0
+#define KSZ8081_LMD_STAT_OPEN 1
+#define KSZ8081_LMD_STAT_SHORT 2
+#define KSZ8081_LMD_STAT_FAIL 3
+#define KSZ8081_LMD_STAT_MASK GENMASK(14, 13)
+/* Short cable (<10 meter) has been detected by LinkMD */
+#define KSZ8081_LMD_SHORT_INDICATOR BIT(12)
+#define KSZ8081_LMD_DELTA_TIME_MASK GENMASK(8, 0)
+
/* PHY Control 1 */
#define MII_KSZPHY_CTRL_1 0x1e
#define KSZ8081_CTRL1_MDIX_STAT BIT(4)
@@ -1366,6 +1379,167 @@ static int kszphy_probe(struct phy_device *phydev)
return 0;
}
+static int ksz886x_cable_test_start(struct phy_device *phydev)
+{
+ if (phydev->dev_flags & MICREL_KSZ8_P1_ERRATA)
+ return -EOPNOTSUPP;
+
+ /* If autoneg is enabled, we won't be able to test cross pair
+ * short. In this case, the PHY will "detect" a link and
+ * confuse the internal state machine - disable auto neg here.
+ * If autoneg is disabled, we should set the speed to 10mbit.
+ */
+ return phy_clear_bits(phydev, MII_BMCR, BMCR_ANENABLE | BMCR_SPEED100);
+}
+
+static int ksz886x_cable_test_result_trans(u16 status)
+{
+ switch (FIELD_GET(KSZ8081_LMD_STAT_MASK, status)) {
+ case KSZ8081_LMD_STAT_NORMAL:
+ return ETHTOOL_A_CABLE_RESULT_CODE_OK;
+ case KSZ8081_LMD_STAT_SHORT:
+ return ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT;
+ case KSZ8081_LMD_STAT_OPEN:
+ return ETHTOOL_A_CABLE_RESULT_CODE_OPEN;
+ case KSZ8081_LMD_STAT_FAIL:
+ fallthrough;
+ default:
+ return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC;
+ }
+}
+
+static bool ksz886x_cable_test_failed(u16 status)
+{
+ return FIELD_GET(KSZ8081_LMD_STAT_MASK, status) ==
+ KSZ8081_LMD_STAT_FAIL;
+}
+
+static bool ksz886x_cable_test_fault_length_valid(u16 status)
+{
+ switch (FIELD_GET(KSZ8081_LMD_STAT_MASK, status)) {
+ case KSZ8081_LMD_STAT_OPEN:
+ fallthrough;
+ case KSZ8081_LMD_STAT_SHORT:
+ return true;
+ }
+ return false;
+}
+
+static int ksz886x_cable_test_fault_length(u16 status)
+{
+ int dt;
+
+ /* According to the data sheet the distance to the fault is
+ * DELTA_TIME * 0.4 meters.
+ */
+ dt = FIELD_GET(KSZ8081_LMD_DELTA_TIME_MASK, status);
+
+ return (dt * 400) / 10;
+}
+
+static int ksz886x_cable_test_wait_for_completion(struct phy_device *phydev)
+{
+ int val, ret;
+
+ ret = phy_read_poll_timeout(phydev, KSZ8081_LMD, val,
+ !(val & KSZ8081_LMD_ENABLE_TEST),
+ 30000, 100000, true);
+
+ return ret < 0 ? ret : 0;
+}
+
+static int ksz886x_cable_test_one_pair(struct phy_device *phydev, int pair)
+{
+ static const int ethtool_pair[] = {
+ ETHTOOL_A_CABLE_PAIR_A,
+ ETHTOOL_A_CABLE_PAIR_B,
+ };
+ int ret, val, mdix;
+
+ /* There is no way to choice the pair, like we do one ksz9031.
+ * We can workaround this limitation by using the MDI-X functionality.
+ */
+ if (pair == 0)
+ mdix = ETH_TP_MDI;
+ else
+ mdix = ETH_TP_MDI_X;
+
+ switch (phydev->phy_id & MICREL_PHY_ID_MASK) {
+ case PHY_ID_KSZ8081:
+ ret = ksz8081_config_mdix(phydev, mdix);
+ break;
+ case PHY_ID_KSZ886X:
+ ret = ksz886x_config_mdix(phydev, mdix);
+ break;
+ default:
+ ret = -ENODEV;
+ }
+
+ if (ret)
+ return ret;
+
+ /* Now we are ready to fire. This command will send a 100ns pulse
+ * to the pair.
+ */
+ ret = phy_write(phydev, KSZ8081_LMD, KSZ8081_LMD_ENABLE_TEST);
+ if (ret)
+ return ret;
+
+ ret = ksz886x_cable_test_wait_for_completion(phydev);
+ if (ret)
+ return ret;
+
+ val = phy_read(phydev, KSZ8081_LMD);
+ if (val < 0)
+ return val;
+
+ if (ksz886x_cable_test_failed(val))
+ return -EAGAIN;
+
+ ret = ethnl_cable_test_result(phydev, ethtool_pair[pair],
+ ksz886x_cable_test_result_trans(val));
+ if (ret)
+ return ret;
+
+ if (!ksz886x_cable_test_fault_length_valid(val))
+ return 0;
+
+ return ethnl_cable_test_fault_length(phydev, ethtool_pair[pair],
+ ksz886x_cable_test_fault_length(val));
+}
+
+static int ksz886x_cable_test_get_status(struct phy_device *phydev,
+ bool *finished)
+{
+ unsigned long pair_mask = 0x3;
+ int retries = 20;
+ int pair, ret;
+
+ *finished = false;
+
+ /* Try harder if link partner is active */
+ while (pair_mask && retries--) {
+ for_each_set_bit(pair, &pair_mask, 4) {
+ ret = ksz886x_cable_test_one_pair(phydev, pair);
+ if (ret == -EAGAIN)
+ continue;
+ if (ret < 0)
+ return ret;
+ clear_bit(pair, &pair_mask);
+ }
+ /* If link partner is in autonegotiation mode it will send 2ms
+ * of FLPs with at least 6ms of silence.
+ * Add 2ms sleep to have better chances to hit this silence.
+ */
+ if (pair_mask)
+ msleep(2);
+ }
+
+ *finished = true;
+
+ return ret;
+}
+
static struct phy_driver ksphy_driver[] = {
{
.phy_id = PHY_ID_KS8737,
@@ -1472,6 +1646,7 @@ static struct phy_driver ksphy_driver[] = {
.phy_id = PHY_ID_KSZ8081,
.name = "Micrel KSZ8081 or KSZ8091",
.phy_id_mask = MICREL_PHY_ID_MASK,
+ .flags = PHY_POLL_CABLE_TEST,
/* PHY_BASIC_FEATURES */
.driver_data = &ksz8081_type,
.probe = kszphy_probe,
@@ -1486,6 +1661,8 @@ static struct phy_driver ksphy_driver[] = {
.get_stats = kszphy_get_stats,
.suspend = kszphy_suspend,
.resume = kszphy_resume,
+ .cable_test_start = ksz886x_cable_test_start,
+ .cable_test_get_status = ksz886x_cable_test_get_status,
}, {
.phy_id = PHY_ID_KSZ8061,
.name = "Micrel KSZ8061",
@@ -1574,11 +1751,14 @@ static struct phy_driver ksphy_driver[] = {
.phy_id_mask = MICREL_PHY_ID_MASK,
.name = "Micrel KSZ8851 Ethernet MAC or KSZ886X Switch",
/* PHY_BASIC_FEATURES */
+ .flags = PHY_POLL_CABLE_TEST,
.config_init = kszphy_config_init,
.config_aneg = ksz886x_config_aneg,
.read_status = ksz886x_read_status,
.suspend = genphy_suspend,
.resume = genphy_resume,
+ .cable_test_start = ksz886x_cable_test_start,
+ .cable_test_get_status = ksz886x_cable_test_get_status,
}, {
.name = "Micrel KSZ87XX Switch",
/* PHY_BASIC_FEATURES */
diff --git a/include/linux/micrel_phy.h b/include/linux/micrel_phy.h
index 58370abd9f4f..3d43c60b49fa 100644
--- a/include/linux/micrel_phy.h
+++ b/include/linux/micrel_phy.h
@@ -39,6 +39,7 @@
/* struct phy_device dev_flags definitions */
#define MICREL_PHY_50MHZ_CLK 0x00000001
#define MICREL_PHY_FXEN 0x00000002
+#define MICREL_KSZ8_P1_ERRATA 0x00000003
#define MICREL_KSZ9021_EXTREG_CTRL 0xB
#define MICREL_KSZ9021_EXTREG_DATA_WRITE 0xC
--
2.29.2
^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH net-next v5 0/8] provide cable test support for the ksz886x switch
2021-06-14 4:31 [PATCH net-next v5 0/8] provide cable test support for the ksz886x switch Oleksij Rempel
` (7 preceding siblings ...)
2021-06-14 4:31 ` [PATCH net-next v5 8/8] net: phy: micrel: ksz886x/ksz8081: add cabletest support Oleksij Rempel
@ 2021-06-14 20:00 ` patchwork-bot+netdevbpf
8 siblings, 0 replies; 10+ messages in thread
From: patchwork-bot+netdevbpf @ 2021-06-14 20:00 UTC (permalink / raw)
To: Oleksij Rempel
Cc: woojung.huh, UNGLinuxDriver, andrew, f.fainelli, vivien.didelot,
olteanv, davem, kuba, kernel, netdev, linux-kernel, linux,
m.grzeschik
Hello:
This series was applied to netdev/net-next.git (refs/heads/master):
On Mon, 14 Jun 2021 06:31:17 +0200 you wrote:
> changes v5:
> - drop resume() patch
> - add Reviewed-by tags.
> - rework dsa_slave_phy_connect() patch
>
> changes v4:
> - use fallthrough;
> - use EOPNOTSUPP instead of ENOTSUPP
> - drop flags variable in dsa_slave_phy_connect patch
> - extend description for the "net: phy: micrel: apply resume errat"
> patch
> - fix "use consistent alignments" patch
>
> [...]
Here is the summary with links:
- [net-next,v5,1/8] net: phy: micrel: move phy reg offsets to common header
https://git.kernel.org/netdev/net-next/c/ec4b94f9b37b
- [net-next,v5,2/8] net: dsa: microchip: ksz8795: add phylink support
https://git.kernel.org/netdev/net-next/c/2c709e0bdad4
- [net-next,v5,3/8] net: phy: micrel: use consistent alignments
https://git.kernel.org/netdev/net-next/c/0033f890f95b
- [net-next,v5,4/8] net: phy/dsa micrel/ksz886x add MDI-X support
https://git.kernel.org/netdev/net-next/c/52939393bd68
- [net-next,v5,5/8] net: phy: micrel: ksz8081 add MDI-X support
https://git.kernel.org/netdev/net-next/c/f873f112553b
- [net-next,v5,6/8] net: dsa: microchip: ksz8795: add LINK_MD register support
https://git.kernel.org/netdev/net-next/c/36838050c453
- [net-next,v5,7/8] net: dsa: dsa_slave_phy_connect(): extend phy's flags with port specific phy flags
https://git.kernel.org/netdev/net-next/c/c916e8e1ea72
- [net-next,v5,8/8] net: phy: micrel: ksz886x/ksz8081: add cabletest support
https://git.kernel.org/netdev/net-next/c/49011e0c1555
You are awesome, thank you!
--
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2021-06-14 20:00 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-06-14 4:31 [PATCH net-next v5 0/8] provide cable test support for the ksz886x switch Oleksij Rempel
2021-06-14 4:31 ` [PATCH net-next v5 1/8] net: phy: micrel: move phy reg offsets to common header Oleksij Rempel
2021-06-14 4:31 ` [PATCH net-next v5 2/8] net: dsa: microchip: ksz8795: add phylink support Oleksij Rempel
2021-06-14 4:31 ` [PATCH net-next v5 3/8] net: phy: micrel: use consistent alignments Oleksij Rempel
2021-06-14 4:31 ` [PATCH net-next v5 4/8] net: phy/dsa micrel/ksz886x add MDI-X support Oleksij Rempel
2021-06-14 4:31 ` [PATCH net-next v5 5/8] net: phy: micrel: ksz8081 " Oleksij Rempel
2021-06-14 4:31 ` [PATCH net-next v5 6/8] net: dsa: microchip: ksz8795: add LINK_MD register support Oleksij Rempel
2021-06-14 4:31 ` [PATCH net-next v5 7/8] net: dsa: dsa_slave_phy_connect(): extend phy's flags with port specific phy flags Oleksij Rempel
2021-06-14 4:31 ` [PATCH net-next v5 8/8] net: phy: micrel: ksz886x/ksz8081: add cabletest support Oleksij Rempel
2021-06-14 20:00 ` [PATCH net-next v5 0/8] provide cable test support for the ksz886x switch patchwork-bot+netdevbpf
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.