[PATCH 5.4 00/17] 5.4.159-rc1 review

[PATCH 5.4 00/17] 5.4.159-rc1 review

[Greg Kroah-Hartman]

This is the start of the stable review cycle for the 5.4.159 release.
There are 17 patches in this series, all will be posted as a response
to this one.  If anyone has any issues with these being applied, please
let me know.

Responses should be made by Fri, 12 Nov 2021 18:19:54 +0000.
Anything received after that time might be too late.

The whole patch series can be found in one patch at:
	https://www.kernel.org/pub/linux/kernel/v5.x/stable-review/patch-5.4.159-rc1.gz
or in the git tree and branch at:
	git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-5.4.y
and the diffstat can be found below.

thanks,

greg k-h

-------------
Pseudo-Shortlog of commits:

Greg Kroah-Hartman <gregkh@linuxfoundation.org>
    Linux 5.4.159-rc1

Johan Hovold <johan@kernel.org>
    rsi: fix control-message timeout

Gustavo A. R. Silva <gustavoars@kernel.org>
    media: staging/intel-ipu3: css: Fix wrong size comparison imgu_css_fw_init

Johan Hovold <johan@kernel.org>
    staging: rtl8192u: fix control-message timeouts

Johan Hovold <johan@kernel.org>
    staging: r8712u: fix control-message timeout

Johan Hovold <johan@kernel.org>
    comedi: vmk80xx: fix bulk and interrupt message timeouts

Johan Hovold <johan@kernel.org>
    comedi: vmk80xx: fix bulk-buffer overflow

Johan Hovold <johan@kernel.org>
    comedi: vmk80xx: fix transfer-buffer overflows

Johan Hovold <johan@kernel.org>
    comedi: ni_usb6501: fix NULL-deref in command paths

Johan Hovold <johan@kernel.org>
    comedi: dt9812: fix DMA buffers on stack

Jan Kara <jack@suse.cz>
    isofs: Fix out of bound access for corrupted isofs image

Petr Mladek <pmladek@suse.com>
    printk/console: Allow to disable console output by using console="" or console=null

Todd Kjos <tkjos@google.com>
    binder: don't detect sender/target during buffer cleanup

James Buren <braewoods+lkml@braewoods.net>
    usb-storage: Add compatibility quirk flags for iODD 2531/2541

Viraj Shah <viraj.shah@linutronix.de>
    usb: musb: Balance list entry in musb_gadget_queue

Geert Uytterhoeven <geert@linux-m68k.org>
    usb: gadget: Mark USB_FSL_QE broken on 64-bit

Neal Liu <neal_liu@aspeedtech.com>
    usb: ehci: handshake CMD_RUN instead of STS_HALT

Juergen Gross <jgross@suse.com>
    Revert "x86/kvm: fix vcpu-id indexed array sizes"


-------------

Diffstat:

 Makefile                                    |   4 +-
 arch/x86/kvm/ioapic.c                       |   2 +-
 arch/x86/kvm/ioapic.h                       |   4 +-
 drivers/android/binder.c                    |  14 ++--
 drivers/net/wireless/rsi/rsi_91x_usb.c      |   2 +-
 drivers/staging/comedi/drivers/dt9812.c     | 115 +++++++++++++++++++++-------
 drivers/staging/comedi/drivers/ni_usb6501.c |  10 +++
 drivers/staging/comedi/drivers/vmk80xx.c    |  28 +++----
 drivers/staging/media/ipu3/ipu3-css-fw.c    |   7 +-
 drivers/staging/media/ipu3/ipu3-css-fw.h    |   2 +-
 drivers/staging/rtl8192u/r8192U_core.c      |  18 ++---
 drivers/staging/rtl8712/usb_ops_linux.c     |   2 +-
 drivers/usb/gadget/udc/Kconfig              |   1 +
 drivers/usb/host/ehci-hcd.c                 |  11 ++-
 drivers/usb/host/ehci-platform.c            |   6 ++
 drivers/usb/host/ehci.h                     |   1 +
 drivers/usb/musb/musb_gadget.c              |   4 +-
 drivers/usb/storage/unusual_devs.h          |  10 +++
 fs/isofs/inode.c                            |   2 +
 kernel/printk/printk.c                      |   9 ++-
 20 files changed, 179 insertions(+), 73 deletions(-)

[PATCH 5.4 01/17] Revert "x86/kvm: fix vcpu-id indexed array sizes"

[Greg Kroah-Hartman]

From: Juergen Gross <jgross@suse.com>

commit 1e254d0d86a0f2efd4190a89d5204b37c18c6381 upstream.

This reverts commit 76b4f357d0e7d8f6f0013c733e6cba1773c266d3.

The commit has the wrong reasoning, as KVM_MAX_VCPU_ID is not defining the
maximum allowed vcpu-id as its name suggests, but the number of vcpu-ids.
So revert this patch again.

Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210913135745.13944-2-jgross@suse.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 arch/x86/kvm/ioapic.c |    2 +-
 arch/x86/kvm/ioapic.h |    4 ++--
 2 files changed, 3 insertions(+), 3 deletions(-)

--- a/arch/x86/kvm/ioapic.c
+++ b/arch/x86/kvm/ioapic.c
@@ -91,7 +91,7 @@ static unsigned long ioapic_read_indirec
 static void rtc_irq_eoi_tracking_reset(struct kvm_ioapic *ioapic)
 {
 	ioapic->rtc_status.pending_eoi = 0;
-	bitmap_zero(ioapic->rtc_status.dest_map.map, KVM_MAX_VCPU_ID + 1);
+	bitmap_zero(ioapic->rtc_status.dest_map.map, KVM_MAX_VCPU_ID);
 }
 
 static void kvm_rtc_eoi_tracking_restore_all(struct kvm_ioapic *ioapic);
--- a/arch/x86/kvm/ioapic.h
+++ b/arch/x86/kvm/ioapic.h
@@ -43,13 +43,13 @@ struct kvm_vcpu;
 
 struct dest_map {
 	/* vcpu bitmap where IRQ has been sent */
-	DECLARE_BITMAP(map, KVM_MAX_VCPU_ID + 1);
+	DECLARE_BITMAP(map, KVM_MAX_VCPU_ID);
 
 	/*
 	 * Vector sent to a given vcpu, only valid when
 	 * the vcpu's bit in map is set
 	 */
-	u8 vectors[KVM_MAX_VCPU_ID + 1];
+	u8 vectors[KVM_MAX_VCPU_ID];
 };
 
 

[PATCH 5.4 02/17] usb: ehci: handshake CMD_RUN instead of STS_HALT

[Greg Kroah-Hartman]

From: Neal Liu <neal_liu@aspeedtech.com>

commit 7f2d73788d9067fd4f677ac5f60ffd25945af7af upstream.

For Aspeed, HCHalted status depends on not only Run/Stop but also
ASS/PSS status.
Handshake CMD_RUN on startup instead.

Tested-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Tao Ren <rentao.bupt@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Neal Liu <neal_liu@aspeedtech.com>
Link: https://lore.kernel.org/r/20210910073619.26095-1-neal_liu@aspeedtech.com
Cc: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/usb/host/ehci-hcd.c      |   11 ++++++++++-
 drivers/usb/host/ehci-platform.c |    6 ++++++
 drivers/usb/host/ehci.h          |    1 +
 3 files changed, 17 insertions(+), 1 deletion(-)

--- a/drivers/usb/host/ehci-hcd.c
+++ b/drivers/usb/host/ehci-hcd.c
@@ -634,7 +634,16 @@ static int ehci_run (struct usb_hcd *hcd
 	/* Wait until HC become operational */
 	ehci_readl(ehci, &ehci->regs->command);	/* unblock posted writes */
 	msleep(5);
-	rc = ehci_handshake(ehci, &ehci->regs->status, STS_HALT, 0, 100 * 1000);
+
+	/* For Aspeed, STS_HALT also depends on ASS/PSS status.
+	 * Check CMD_RUN instead.
+	 */
+	if (ehci->is_aspeed)
+		rc = ehci_handshake(ehci, &ehci->regs->command, CMD_RUN,
+				    1, 100 * 1000);
+	else
+		rc = ehci_handshake(ehci, &ehci->regs->status, STS_HALT,
+				    0, 100 * 1000);
 
 	up_write(&ehci_cf_port_reset_rwsem);
 
--- a/drivers/usb/host/ehci-platform.c
+++ b/drivers/usb/host/ehci-platform.c
@@ -286,6 +286,12 @@ static int ehci_platform_probe(struct pl
 					  "has-transaction-translator"))
 			hcd->has_tt = 1;
 
+		if (of_device_is_compatible(dev->dev.of_node,
+					    "aspeed,ast2500-ehci") ||
+		    of_device_is_compatible(dev->dev.of_node,
+					    "aspeed,ast2600-ehci"))
+			ehci->is_aspeed = 1;
+
 		if (soc_device_match(quirk_poll_match))
 			priv->quirk_poll = true;
 
--- a/drivers/usb/host/ehci.h
+++ b/drivers/usb/host/ehci.h
@@ -218,6 +218,7 @@ struct ehci_hcd {			/* one per controlle
 	unsigned		frame_index_bug:1; /* MosChip (AKA NetMos) */
 	unsigned		need_oc_pp_cycle:1; /* MPC834X port power */
 	unsigned		imx28_write_fix:1; /* For Freescale i.MX28 */
+	unsigned		is_aspeed:1;
 
 	/* required for usb32 quirk */
 	#define OHCI_CTRL_HCFS          (3 << 6)

[PATCH 5.4 03/17] usb: gadget: Mark USB_FSL_QE broken on 64-bit

[Greg Kroah-Hartman]

From: Geert Uytterhoeven <geert@linux-m68k.org>

commit a0548b26901f082684ad1fb3ba397d2de3a1406a upstream.

On 64-bit:

    drivers/usb/gadget/udc/fsl_qe_udc.c: In function ‘qe_ep0_rx’:
    drivers/usb/gadget/udc/fsl_qe_udc.c:842:13: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
      842 |     vaddr = (u32)phys_to_virt(in_be32(&bd->buf));
	  |             ^
    In file included from drivers/usb/gadget/udc/fsl_qe_udc.c:41:
    drivers/usb/gadget/udc/fsl_qe_udc.c:843:28: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
      843 |     frame_set_data(pframe, (u8 *)vaddr);
	  |                            ^

The driver assumes physical and virtual addresses are 32-bit, hence it
cannot work on 64-bit platforms.

Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20211027080849.3276289-1-geert@linux-m68k.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/usb/gadget/udc/Kconfig |    1 +
 1 file changed, 1 insertion(+)

--- a/drivers/usb/gadget/udc/Kconfig
+++ b/drivers/usb/gadget/udc/Kconfig
@@ -330,6 +330,7 @@ config USB_AMD5536UDC
 config USB_FSL_QE
 	tristate "Freescale QE/CPM USB Device Controller"
 	depends on FSL_SOC && (QUICC_ENGINE || CPM)
+	depends on !64BIT || BROKEN
 	help
 	   Some of Freescale PowerPC processors have a Full Speed
 	   QE/CPM2 USB controller, which support device mode with 4

[PATCH 5.4 04/17] usb: musb: Balance list entry in musb_gadget_queue

[Greg Kroah-Hartman]

From: Viraj Shah <viraj.shah@linutronix.de>

commit 21b5fcdccb32ff09b6b63d4a83c037150665a83f upstream.

musb_gadget_queue() adds the passed request to musb_ep::req_list. If the
endpoint is idle and it is the first request then it invokes
musb_queue_resume_work(). If the function returns an error then the
error is passed to the caller without any clean-up and the request
remains enqueued on the list. If the caller enqueues the request again
then the list corrupts.

Remove the request from the list on error.

Fixes: ea2f35c01d5ea ("usb: musb: Fix sleeping function called from invalid context for hdrc glue")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Viraj Shah <viraj.shah@linutronix.de>
Link: https://lore.kernel.org/r/20211021093644.4734-1-viraj.shah@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/usb/musb/musb_gadget.c |    4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

--- a/drivers/usb/musb/musb_gadget.c
+++ b/drivers/usb/musb/musb_gadget.c
@@ -1248,9 +1248,11 @@ static int musb_gadget_queue(struct usb_
 		status = musb_queue_resume_work(musb,
 						musb_ep_restart_resume_work,
 						request);
-		if (status < 0)
+		if (status < 0) {
 			dev_err(musb->controller, "%s resume work: %i\n",
 				__func__, status);
+			list_del(&request->list);
+		}
 	}
 
 unlock:

[PATCH 5.4 05/17] usb-storage: Add compatibility quirk flags for iODD 2531/2541

[Greg Kroah-Hartman]

From: James Buren <braewoods+lkml@braewoods.net>

commit 05c8f1b67e67dcd786ae3fe44492bbc617b4bd12 upstream.

These drive enclosures have firmware bugs that make it impossible to mount
a new virtual ISO image after Linux ejects the old one if the device is
locked by Linux. Windows bypasses this problem by the fact that they do
not lock the device. Add a quirk to disable device locking for these
drive enclosures.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Buren <braewoods+lkml@braewoods.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211014015504.2695089-1-braewoods+lkml@braewoods.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/usb/storage/unusual_devs.h |   10 ++++++++++
 1 file changed, 10 insertions(+)

--- a/drivers/usb/storage/unusual_devs.h
+++ b/drivers/usb/storage/unusual_devs.h
@@ -407,6 +407,16 @@ UNUSUAL_DEV(  0x04b8, 0x0602, 0x0110, 0x
 		USB_SC_SCSI, USB_PR_BULK, NULL, US_FL_SINGLE_LUN),
 
 /*
+ * Reported by James Buren <braewoods+lkml@braewoods.net>
+ * Virtual ISOs cannot be remounted if ejected while the device is locked
+ * Disable locking to mimic Windows behavior that bypasses the issue
+ */
+UNUSUAL_DEV(  0x04c5, 0x2028, 0x0001, 0x0001,
+		"iODD",
+		"2531/2541",
+		USB_SC_DEVICE, USB_PR_DEVICE, NULL, US_FL_NOT_LOCKABLE),
+
+/*
  * Not sure who reported this originally but
  * Pavel Machek <pavel@ucw.cz> reported that the extra US_FL_SINGLE_LUN
  * flag be added */

[PATCH 5.4 06/17] binder: dont detect sender/target during buffer cleanup

[Greg Kroah-Hartman]

From: Todd Kjos <tkjos@google.com>

commit 32e9f56a96d8d0f23cb2aeb2a3cd18d40393e787 upstream.

When freeing txn buffers, binder_transaction_buffer_release()
attempts to detect whether the current context is the target by
comparing current->group_leader to proc->tsk. This is an unreliable
test. Instead explicitly pass an 'is_failure' boolean.

Detecting the sender was being used as a way to tell if the
transaction failed to be sent.  When cleaning up after
failing to send a transaction, there is no need to close
the fds associated with a BINDER_TYPE_FDA object. Now
'is_failure' can be used to accurately detect this case.

Fixes: 44d8047f1d87 ("binder: use standard functions to allocate fds")
Cc: stable <stable@vger.kernel.org>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20211015233811.3532235-1-tkjos@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/android/binder.c |   14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)

--- a/drivers/android/binder.c
+++ b/drivers/android/binder.c
@@ -2257,7 +2257,7 @@ static void binder_transaction_buffer_re
 		binder_dec_node(buffer->target_node, 1, 0);
 
 	off_start_offset = ALIGN(buffer->data_size, sizeof(void *));
-	off_end_offset = is_failure ? failed_at :
+	off_end_offset = is_failure && failed_at ? failed_at :
 				off_start_offset + buffer->offsets_size;
 	for (buffer_offset = off_start_offset; buffer_offset < off_end_offset;
 	     buffer_offset += sizeof(binder_size_t)) {
@@ -2343,9 +2343,8 @@ static void binder_transaction_buffer_re
 			binder_size_t fd_buf_size;
 			binder_size_t num_valid;
 
-			if (proc->tsk != current->group_leader) {
+			if (is_failure) {
 				/*
-				 * Nothing to do if running in sender context
 				 * The fd fixups have not been applied so no
 				 * fds need to be closed.
 				 */
@@ -3548,6 +3547,7 @@ err_invalid_target_handle:
  * binder_free_buf() - free the specified buffer
  * @proc:	binder proc that owns buffer
  * @buffer:	buffer to be freed
+ * @is_failure:	failed to send transaction
  *
  * If buffer for an async transaction, enqueue the next async
  * transaction from the node.
@@ -3557,7 +3557,7 @@ err_invalid_target_handle:
 static void
 binder_free_buf(struct binder_proc *proc,
 		struct binder_thread *thread,
-		struct binder_buffer *buffer)
+		struct binder_buffer *buffer, bool is_failure)
 {
 	binder_inner_proc_lock(proc);
 	if (buffer->transaction) {
@@ -3585,7 +3585,7 @@ binder_free_buf(struct binder_proc *proc
 		binder_node_inner_unlock(buf_node);
 	}
 	trace_binder_transaction_buffer_release(buffer);
-	binder_transaction_buffer_release(proc, thread, buffer, 0, false);
+	binder_transaction_buffer_release(proc, thread, buffer, 0, is_failure);
 	binder_alloc_free_buf(&proc->alloc, buffer);
 }
 
@@ -3786,7 +3786,7 @@ static int binder_thread_write(struct bi
 				     proc->pid, thread->pid, (u64)data_ptr,
 				     buffer->debug_id,
 				     buffer->transaction ? "active" : "finished");
-			binder_free_buf(proc, thread, buffer);
+			binder_free_buf(proc, thread, buffer, false);
 			break;
 		}
 
@@ -4474,7 +4474,7 @@ retry:
 			buffer->transaction = NULL;
 			binder_cleanup_transaction(t, "fd fixups failed",
 						   BR_FAILED_REPLY);
-			binder_free_buf(proc, thread, buffer);
+			binder_free_buf(proc, thread, buffer, true);
 			binder_debug(BINDER_DEBUG_FAILED_TRANSACTION,
 				     "%d:%d %stransaction %d fd fixups failed %d/%d, line %d\n",
 				     proc->pid, thread->pid,

[PATCH 5.4 07/17] printk/console: Allow to disable console output by using console="" or console=null

[Greg Kroah-Hartman]

From: Petr Mladek <pmladek@suse.com>

commit 3cffa06aeef7ece30f6b5ac0ea51f264e8fea4d0 upstream.

The commit 48021f98130880dd74 ("printk: handle blank console arguments
passed in.") prevented crash caused by empty console= parameter value.

Unfortunately, this value is widely used on Chromebooks to disable
the console output. The above commit caused performance regression
because the messages were pushed on slow console even though nobody
was watching it.

Use ttynull driver explicitly for console="" and console=null
parameters. It has been created for exactly this purpose.

It causes that preferred_console is set. As a result, ttySX and ttyX
are not used as a fallback. And only ttynull console gets registered by
default.

It still allows to register other consoles either by additional console=
parameters or SPCR. It prevents regression because it worked this way even
before. Also it is a sane semantic. Preventing output on all consoles
should be done another way, for example, by introducing mute_console
parameter.

Link: https://lore.kernel.org/r/20201006025935.GA597@jagdpanzerIV.localdomain
Suggested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20201111135450.11214-3-pmladek@suse.com
Cc: Yi Fan <yfa@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 kernel/printk/printk.c |    9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

--- a/kernel/printk/printk.c
+++ b/kernel/printk/printk.c
@@ -2193,8 +2193,15 @@ static int __init console_setup(char *st
 	char *s, *options, *brl_options = NULL;
 	int idx;
 
-	if (str[0] == 0)
+	/*
+	 * console="" or console=null have been suggested as a way to
+	 * disable console output. Use ttynull that has been created
+	 * for exacly this purpose.
+	 */
+	if (str[0] == 0 || strcmp(str, "null") == 0) {
+		__add_preferred_console("ttynull", 0, NULL, NULL);
 		return 1;
+	}
 
 	if (_braille_console_setup(&str, &brl_options))
 		return 1;

[PATCH 5.4 08/17] isofs: Fix out of bound access for corrupted isofs image

[Greg Kroah-Hartman]

From: Jan Kara <jack@suse.cz>

commit e96a1866b40570b5950cda8602c2819189c62a48 upstream.

When isofs image is suitably corrupted isofs_read_inode() can read data
beyond the end of buffer. Sanity-check the directory entry length before
using it.

Reported-and-tested-by: syzbot+6fc7fb214625d82af7d1@syzkaller.appspotmail.com
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 fs/isofs/inode.c |    2 ++
 1 file changed, 2 insertions(+)

--- a/fs/isofs/inode.c
+++ b/fs/isofs/inode.c
@@ -1328,6 +1328,8 @@ static int isofs_read_inode(struct inode
 
 	de = (struct iso_directory_record *) (bh->b_data + offset);
 	de_len = *(unsigned char *) de;
+	if (de_len < sizeof(struct iso_directory_record))
+		goto fail;
 
 	if (offset + de_len > bufsize) {
 		int frag1 = bufsize - offset;

[PATCH 5.4 09/17] comedi: dt9812: fix DMA buffers on stack

[Greg Kroah-Hartman]

From: Johan Hovold <johan@kernel.org>

commit 536de747bc48262225889a533db6650731ab25d3 upstream.

USB transfer buffers are typically mapped for DMA and must not be
allocated on the stack or transfers will fail.

Allocate proper transfer buffers in the various command helpers and
return an error on short transfers instead of acting on random stack
data.

Note that this also fixes a stack info leak on systems where DMA is not
used as 32 bytes are always sent to the device regardless of how short
the command is.

Fixes: 63274cd7d38a ("Staging: comedi: add usb dt9812 driver")
Cc: stable@vger.kernel.org      # 2.6.29
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211027093529.30896-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/staging/comedi/drivers/dt9812.c |  115 +++++++++++++++++++++++---------
 1 file changed, 86 insertions(+), 29 deletions(-)

--- a/drivers/staging/comedi/drivers/dt9812.c
+++ b/drivers/staging/comedi/drivers/dt9812.c
@@ -32,6 +32,7 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/errno.h>
+#include <linux/slab.h>
 #include <linux/uaccess.h>
 
 #include "../comedi_usb.h"
@@ -237,22 +238,42 @@ static int dt9812_read_info(struct comed
 {
 	struct usb_device *usb = comedi_to_usb_dev(dev);
 	struct dt9812_private *devpriv = dev->private;
-	struct dt9812_usb_cmd cmd;
+	struct dt9812_usb_cmd *cmd;
+	size_t tbuf_size;
 	int count, ret;
+	void *tbuf;
 
-	cmd.cmd = cpu_to_le32(DT9812_R_FLASH_DATA);
-	cmd.u.flash_data_info.address =
+	tbuf_size = max(sizeof(*cmd), buf_size);
+
+	tbuf = kzalloc(tbuf_size, GFP_KERNEL);
+	if (!tbuf)
+		return -ENOMEM;
+
+	cmd = tbuf;
+
+	cmd->cmd = cpu_to_le32(DT9812_R_FLASH_DATA);
+	cmd->u.flash_data_info.address =
 	    cpu_to_le16(DT9812_DIAGS_BOARD_INFO_ADDR + offset);
-	cmd.u.flash_data_info.numbytes = cpu_to_le16(buf_size);
+	cmd->u.flash_data_info.numbytes = cpu_to_le16(buf_size);
 
 	/* DT9812 only responds to 32 byte writes!! */
 	ret = usb_bulk_msg(usb, usb_sndbulkpipe(usb, devpriv->cmd_wr.addr),
-			   &cmd, 32, &count, DT9812_USB_TIMEOUT);
+			   cmd, sizeof(*cmd), &count, DT9812_USB_TIMEOUT);
 	if (ret)
-		return ret;
+		goto out;
+
+	ret = usb_bulk_msg(usb, usb_rcvbulkpipe(usb, devpriv->cmd_rd.addr),
+			   tbuf, buf_size, &count, DT9812_USB_TIMEOUT);
+	if (!ret) {
+		if (count == buf_size)
+			memcpy(buf, tbuf, buf_size);
+		else
+			ret = -EREMOTEIO;
+	}
+out:
+	kfree(tbuf);
 
-	return usb_bulk_msg(usb, usb_rcvbulkpipe(usb, devpriv->cmd_rd.addr),
-			    buf, buf_size, &count, DT9812_USB_TIMEOUT);
+	return ret;
 }
 
 static int dt9812_read_multiple_registers(struct comedi_device *dev,
@@ -261,22 +282,42 @@ static int dt9812_read_multiple_register
 {
 	struct usb_device *usb = comedi_to_usb_dev(dev);
 	struct dt9812_private *devpriv = dev->private;
-	struct dt9812_usb_cmd cmd;
+	struct dt9812_usb_cmd *cmd;
 	int i, count, ret;
+	size_t buf_size;
+	void *buf;
+
+	buf_size = max_t(size_t, sizeof(*cmd), reg_count);
+
+	buf = kzalloc(buf_size, GFP_KERNEL);
+	if (!buf)
+		return -ENOMEM;
+
+	cmd = buf;
 
-	cmd.cmd = cpu_to_le32(DT9812_R_MULTI_BYTE_REG);
-	cmd.u.read_multi_info.count = reg_count;
+	cmd->cmd = cpu_to_le32(DT9812_R_MULTI_BYTE_REG);
+	cmd->u.read_multi_info.count = reg_count;
 	for (i = 0; i < reg_count; i++)
-		cmd.u.read_multi_info.address[i] = address[i];
+		cmd->u.read_multi_info.address[i] = address[i];
 
 	/* DT9812 only responds to 32 byte writes!! */
 	ret = usb_bulk_msg(usb, usb_sndbulkpipe(usb, devpriv->cmd_wr.addr),
-			   &cmd, 32, &count, DT9812_USB_TIMEOUT);
+			   cmd, sizeof(*cmd), &count, DT9812_USB_TIMEOUT);
 	if (ret)
-		return ret;
+		goto out;
 
-	return usb_bulk_msg(usb, usb_rcvbulkpipe(usb, devpriv->cmd_rd.addr),
-			    value, reg_count, &count, DT9812_USB_TIMEOUT);
+	ret = usb_bulk_msg(usb, usb_rcvbulkpipe(usb, devpriv->cmd_rd.addr),
+			   buf, reg_count, &count, DT9812_USB_TIMEOUT);
+	if (!ret) {
+		if (count == reg_count)
+			memcpy(value, buf, reg_count);
+		else
+			ret = -EREMOTEIO;
+	}
+out:
+	kfree(buf);
+
+	return ret;
 }
 
 static int dt9812_write_multiple_registers(struct comedi_device *dev,
@@ -285,19 +326,27 @@ static int dt9812_write_multiple_registe
 {
 	struct usb_device *usb = comedi_to_usb_dev(dev);
 	struct dt9812_private *devpriv = dev->private;
-	struct dt9812_usb_cmd cmd;
+	struct dt9812_usb_cmd *cmd;
 	int i, count;
+	int ret;
 
-	cmd.cmd = cpu_to_le32(DT9812_W_MULTI_BYTE_REG);
-	cmd.u.read_multi_info.count = reg_count;
+	cmd = kzalloc(sizeof(*cmd), GFP_KERNEL);
+	if (!cmd)
+		return -ENOMEM;
+
+	cmd->cmd = cpu_to_le32(DT9812_W_MULTI_BYTE_REG);
+	cmd->u.read_multi_info.count = reg_count;
 	for (i = 0; i < reg_count; i++) {
-		cmd.u.write_multi_info.write[i].address = address[i];
-		cmd.u.write_multi_info.write[i].value = value[i];
+		cmd->u.write_multi_info.write[i].address = address[i];
+		cmd->u.write_multi_info.write[i].value = value[i];
 	}
 
 	/* DT9812 only responds to 32 byte writes!! */
-	return usb_bulk_msg(usb, usb_sndbulkpipe(usb, devpriv->cmd_wr.addr),
-			    &cmd, 32, &count, DT9812_USB_TIMEOUT);
+	ret = usb_bulk_msg(usb, usb_sndbulkpipe(usb, devpriv->cmd_wr.addr),
+			   cmd, sizeof(*cmd), &count, DT9812_USB_TIMEOUT);
+	kfree(cmd);
+
+	return ret;
 }
 
 static int dt9812_rmw_multiple_registers(struct comedi_device *dev,
@@ -306,17 +355,25 @@ static int dt9812_rmw_multiple_registers
 {
 	struct usb_device *usb = comedi_to_usb_dev(dev);
 	struct dt9812_private *devpriv = dev->private;
-	struct dt9812_usb_cmd cmd;
+	struct dt9812_usb_cmd *cmd;
 	int i, count;
+	int ret;
+
+	cmd = kzalloc(sizeof(*cmd), GFP_KERNEL);
+	if (!cmd)
+		return -ENOMEM;
 
-	cmd.cmd = cpu_to_le32(DT9812_RMW_MULTI_BYTE_REG);
-	cmd.u.rmw_multi_info.count = reg_count;
+	cmd->cmd = cpu_to_le32(DT9812_RMW_MULTI_BYTE_REG);
+	cmd->u.rmw_multi_info.count = reg_count;
 	for (i = 0; i < reg_count; i++)
-		cmd.u.rmw_multi_info.rmw[i] = rmw[i];
+		cmd->u.rmw_multi_info.rmw[i] = rmw[i];
 
 	/* DT9812 only responds to 32 byte writes!! */
-	return usb_bulk_msg(usb, usb_sndbulkpipe(usb, devpriv->cmd_wr.addr),
-			    &cmd, 32, &count, DT9812_USB_TIMEOUT);
+	ret = usb_bulk_msg(usb, usb_sndbulkpipe(usb, devpriv->cmd_wr.addr),
+			   cmd, sizeof(*cmd), &count, DT9812_USB_TIMEOUT);
+	kfree(cmd);
+
+	return ret;
 }
 
 static int dt9812_digital_in(struct comedi_device *dev, u8 *bits)

[PATCH 5.4 10/17] comedi: ni_usb6501: fix NULL-deref in command paths

[Greg Kroah-Hartman]

From: Johan Hovold <johan@kernel.org>

commit 907767da8f3a925b060c740e0b5c92ea7dbec440 upstream.

The driver uses endpoint-sized USB transfer buffers but had no sanity
checks on the sizes. This can lead to zero-size-pointer dereferences or
overflowed transfer buffers in ni6501_port_command() and
ni6501_counter_command() if a (malicious) device has smaller max-packet
sizes than expected (or when doing descriptor fuzz testing).

Add the missing sanity checks to probe().

Fixes: a03bb00e50ab ("staging: comedi: add NI USB-6501 support")
Cc: stable@vger.kernel.org      # 3.18
Cc: Luca Ellero <luca.ellero@brickedbrain.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211027093529.30896-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/staging/comedi/drivers/ni_usb6501.c |   10 ++++++++++
 1 file changed, 10 insertions(+)

--- a/drivers/staging/comedi/drivers/ni_usb6501.c
+++ b/drivers/staging/comedi/drivers/ni_usb6501.c
@@ -144,6 +144,10 @@ static const u8 READ_COUNTER_RESPONSE[]
 					   0x00, 0x00, 0x00, 0x02,
 					   0x00, 0x00, 0x00, 0x00};
 
+/* Largest supported packets */
+static const size_t TX_MAX_SIZE	= sizeof(SET_PORT_DIR_REQUEST);
+static const size_t RX_MAX_SIZE	= sizeof(READ_PORT_RESPONSE);
+
 enum commands {
 	READ_PORT,
 	WRITE_PORT,
@@ -501,6 +505,12 @@ static int ni6501_find_endpoints(struct
 	if (!devpriv->ep_rx || !devpriv->ep_tx)
 		return -ENODEV;
 
+	if (usb_endpoint_maxp(devpriv->ep_rx) < RX_MAX_SIZE)
+		return -ENODEV;
+
+	if (usb_endpoint_maxp(devpriv->ep_tx) < TX_MAX_SIZE)
+		return -ENODEV;
+
 	return 0;
 }
 

[PATCH 5.4 11/17] comedi: vmk80xx: fix transfer-buffer overflows

[Greg Kroah-Hartman]

From: Johan Hovold <johan@kernel.org>

commit a23461c47482fc232ffc9b819539d1f837adf2b1 upstream.

The driver uses endpoint-sized USB transfer buffers but up until
recently had no sanity checks on the sizes.

Commit e1f13c879a7c ("staging: comedi: check validity of wMaxPacketSize
of usb endpoints found") inadvertently fixed NULL-pointer dereferences
when accessing the transfer buffers in case a malicious device has a
zero wMaxPacketSize.

Make sure to allocate buffers large enough to handle also the other
accesses that are done without a size check (e.g. byte 18 in
vmk80xx_cnt_insn_read() for the VMK8061_MODEL) to avoid writing beyond
the buffers, for example, when doing descriptor fuzzing.

The original driver was for a low-speed device with 8-byte buffers.
Support was later added for a device that uses bulk transfers and is
presumably a full-speed device with a maximum 64-byte wMaxPacketSize.

Fixes: 985cafccbf9b ("Staging: Comedi: vmk80xx: Add k8061 support")
Cc: stable@vger.kernel.org      # 2.6.31
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20211025114532.4599-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/staging/comedi/drivers/vmk80xx.c |    6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

--- a/drivers/staging/comedi/drivers/vmk80xx.c
+++ b/drivers/staging/comedi/drivers/vmk80xx.c
@@ -90,6 +90,8 @@ enum {
 #define IC3_VERSION		BIT(0)
 #define IC6_VERSION		BIT(1)
 
+#define MIN_BUF_SIZE		64
+
 enum vmk80xx_model {
 	VMK8055_MODEL,
 	VMK8061_MODEL
@@ -678,12 +680,12 @@ static int vmk80xx_alloc_usb_buffers(str
 	struct vmk80xx_private *devpriv = dev->private;
 	size_t size;
 
-	size = usb_endpoint_maxp(devpriv->ep_rx);
+	size = max(usb_endpoint_maxp(devpriv->ep_rx), MIN_BUF_SIZE);
 	devpriv->usb_rx_buf = kzalloc(size, GFP_KERNEL);
 	if (!devpriv->usb_rx_buf)
 		return -ENOMEM;
 
-	size = usb_endpoint_maxp(devpriv->ep_tx);
+	size = max(usb_endpoint_maxp(devpriv->ep_rx), MIN_BUF_SIZE);
 	devpriv->usb_tx_buf = kzalloc(size, GFP_KERNEL);
 	if (!devpriv->usb_tx_buf)
 		return -ENOMEM;

[PATCH 5.4 12/17] comedi: vmk80xx: fix bulk-buffer overflow

[Greg Kroah-Hartman]

From: Johan Hovold <johan@kernel.org>

commit 78cdfd62bd54af615fba9e3ca1ba35de39d3871d upstream.

The driver is using endpoint-sized buffers but must not assume that the
tx and rx buffers are of equal size or a malicious device could overflow
the slab-allocated receive buffer when doing bulk transfers.

Fixes: 985cafccbf9b ("Staging: Comedi: vmk80xx: Add k8061 support")
Cc: stable@vger.kernel.org      # 2.6.31
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20211025114532.4599-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/staging/comedi/drivers/vmk80xx.c |   16 +++++++---------
 1 file changed, 7 insertions(+), 9 deletions(-)

--- a/drivers/staging/comedi/drivers/vmk80xx.c
+++ b/drivers/staging/comedi/drivers/vmk80xx.c
@@ -159,22 +159,20 @@ static void vmk80xx_do_bulk_msg(struct c
 	__u8 rx_addr;
 	unsigned int tx_pipe;
 	unsigned int rx_pipe;
-	size_t size;
+	size_t tx_size;
+	size_t rx_size;
 
 	tx_addr = devpriv->ep_tx->bEndpointAddress;
 	rx_addr = devpriv->ep_rx->bEndpointAddress;
 	tx_pipe = usb_sndbulkpipe(usb, tx_addr);
 	rx_pipe = usb_rcvbulkpipe(usb, rx_addr);
-
-	/*
-	 * The max packet size attributes of the K8061
-	 * input/output endpoints are identical
-	 */
-	size = usb_endpoint_maxp(devpriv->ep_tx);
+	tx_size = usb_endpoint_maxp(devpriv->ep_tx);
+	rx_size = usb_endpoint_maxp(devpriv->ep_rx);
 
 	usb_bulk_msg(usb, tx_pipe, devpriv->usb_tx_buf,
-		     size, NULL, devpriv->ep_tx->bInterval);
-	usb_bulk_msg(usb, rx_pipe, devpriv->usb_rx_buf, size, NULL, HZ * 10);
+		     tx_size, NULL, devpriv->ep_tx->bInterval);
+
+	usb_bulk_msg(usb, rx_pipe, devpriv->usb_rx_buf, rx_size, NULL, HZ * 10);
 }
 
 static int vmk80xx_read_packet(struct comedi_device *dev)

[PATCH 5.4 13/17] comedi: vmk80xx: fix bulk and interrupt message timeouts

[Greg Kroah-Hartman]

From: Johan Hovold <johan@kernel.org>

commit a56d3e40bda460edf3f8d6aac00ec0b322b4ab83 upstream.

USB bulk and interrupt message timeouts are specified in milliseconds
and should specifically not vary with CONFIG_HZ.

Note that the bulk-out transfer timeout was set to the endpoint
bInterval value, which should be ignored for bulk endpoints and is
typically set to zero. This meant that a failing bulk-out transfer
would never time out.

Assume that the 10 second timeout used for all other transfers is more
than enough also for the bulk-out endpoint.

Fixes: 985cafccbf9b ("Staging: Comedi: vmk80xx: Add k8061 support")
Fixes: 951348b37738 ("staging: comedi: vmk80xx: wait for URBs to complete")
Cc: stable@vger.kernel.org      # 2.6.31
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20211025114532.4599-6-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/staging/comedi/drivers/vmk80xx.c |   12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)

--- a/drivers/staging/comedi/drivers/vmk80xx.c
+++ b/drivers/staging/comedi/drivers/vmk80xx.c
@@ -91,6 +91,7 @@ enum {
 #define IC6_VERSION		BIT(1)
 
 #define MIN_BUF_SIZE		64
+#define PACKET_TIMEOUT		10000	/* ms */
 
 enum vmk80xx_model {
 	VMK8055_MODEL,
@@ -169,10 +170,11 @@ static void vmk80xx_do_bulk_msg(struct c
 	tx_size = usb_endpoint_maxp(devpriv->ep_tx);
 	rx_size = usb_endpoint_maxp(devpriv->ep_rx);
 
-	usb_bulk_msg(usb, tx_pipe, devpriv->usb_tx_buf,
-		     tx_size, NULL, devpriv->ep_tx->bInterval);
+	usb_bulk_msg(usb, tx_pipe, devpriv->usb_tx_buf, tx_size, NULL,
+		     PACKET_TIMEOUT);
 
-	usb_bulk_msg(usb, rx_pipe, devpriv->usb_rx_buf, rx_size, NULL, HZ * 10);
+	usb_bulk_msg(usb, rx_pipe, devpriv->usb_rx_buf, rx_size, NULL,
+		     PACKET_TIMEOUT);
 }
 
 static int vmk80xx_read_packet(struct comedi_device *dev)
@@ -191,7 +193,7 @@ static int vmk80xx_read_packet(struct co
 	pipe = usb_rcvintpipe(usb, ep->bEndpointAddress);
 	return usb_interrupt_msg(usb, pipe, devpriv->usb_rx_buf,
 				 usb_endpoint_maxp(ep), NULL,
-				 HZ * 10);
+				 PACKET_TIMEOUT);
 }
 
 static int vmk80xx_write_packet(struct comedi_device *dev, int cmd)
@@ -212,7 +214,7 @@ static int vmk80xx_write_packet(struct c
 	pipe = usb_sndintpipe(usb, ep->bEndpointAddress);
 	return usb_interrupt_msg(usb, pipe, devpriv->usb_tx_buf,
 				 usb_endpoint_maxp(ep), NULL,
-				 HZ * 10);
+				 PACKET_TIMEOUT);
 }
 
 static int vmk80xx_reset_device(struct comedi_device *dev)

[PATCH 5.4 14/17] staging: r8712u: fix control-message timeout

[Greg Kroah-Hartman]

From: Johan Hovold <johan@kernel.org>

commit ce4940525f36ffdcf4fa623bcedab9c2a6db893a upstream.

USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.

Fixes: 2865d42c78a9 ("staging: r8712u: Add the new driver to the mainline kernel")
Cc: stable@vger.kernel.org      # 2.6.37
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211025120910.6339-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/staging/rtl8712/usb_ops_linux.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/staging/rtl8712/usb_ops_linux.c
+++ b/drivers/staging/rtl8712/usb_ops_linux.c
@@ -493,7 +493,7 @@ int r8712_usbctrl_vendorreq(struct intf_
 		memcpy(pIo_buf, pdata, len);
 	}
 	status = usb_control_msg(udev, pipe, request, reqtype, value, index,
-				 pIo_buf, len, HZ / 2);
+				 pIo_buf, len, 500);
 	if (status > 0) {  /* Success this control transfer. */
 		if (requesttype == 0x01) {
 			/* For Control read transfer, we have to copy the read

[PATCH 5.4 15/17] staging: rtl8192u: fix control-message timeouts

[Greg Kroah-Hartman]

From: Johan Hovold <johan@kernel.org>

commit 4cfa36d312d6789448b59a7aae770ac8425017a3 upstream.

USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.

Fixes: 8fc8598e61f6 ("Staging: Added Realtek rtl8192u driver to staging")
Cc: stable@vger.kernel.org      # 2.6.33
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211025120910.6339-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/staging/rtl8192u/r8192U_core.c |   18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)

--- a/drivers/staging/rtl8192u/r8192U_core.c
+++ b/drivers/staging/rtl8192u/r8192U_core.c
@@ -236,7 +236,7 @@ int write_nic_byte_E(struct net_device *
 
 	status = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
 				 RTL8187_REQ_SET_REGS, RTL8187_REQT_WRITE,
-				 indx | 0xfe00, 0, usbdata, 1, HZ / 2);
+				 indx | 0xfe00, 0, usbdata, 1, 500);
 	kfree(usbdata);
 
 	if (status < 0) {
@@ -258,7 +258,7 @@ int read_nic_byte_E(struct net_device *d
 
 	status = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
 				 RTL8187_REQ_GET_REGS, RTL8187_REQT_READ,
-				 indx | 0xfe00, 0, usbdata, 1, HZ / 2);
+				 indx | 0xfe00, 0, usbdata, 1, 500);
 	*data = *usbdata;
 	kfree(usbdata);
 
@@ -286,7 +286,7 @@ int write_nic_byte(struct net_device *de
 	status = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
 				 RTL8187_REQ_SET_REGS, RTL8187_REQT_WRITE,
 				 (indx & 0xff) | 0xff00, (indx >> 8) & 0x0f,
-				 usbdata, 1, HZ / 2);
+				 usbdata, 1, 500);
 	kfree(usbdata);
 
 	if (status < 0) {
@@ -313,7 +313,7 @@ int write_nic_word(struct net_device *de
 	status = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
 				 RTL8187_REQ_SET_REGS, RTL8187_REQT_WRITE,
 				 (indx & 0xff) | 0xff00, (indx >> 8) & 0x0f,
-				 usbdata, 2, HZ / 2);
+				 usbdata, 2, 500);
 	kfree(usbdata);
 
 	if (status < 0) {
@@ -340,7 +340,7 @@ int write_nic_dword(struct net_device *d
 	status = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
 				 RTL8187_REQ_SET_REGS, RTL8187_REQT_WRITE,
 				 (indx & 0xff) | 0xff00, (indx >> 8) & 0x0f,
-				 usbdata, 4, HZ / 2);
+				 usbdata, 4, 500);
 	kfree(usbdata);
 
 
@@ -367,7 +367,7 @@ int read_nic_byte(struct net_device *dev
 	status = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
 				 RTL8187_REQ_GET_REGS, RTL8187_REQT_READ,
 				 (indx & 0xff) | 0xff00, (indx >> 8) & 0x0f,
-				 usbdata, 1, HZ / 2);
+				 usbdata, 1, 500);
 	*data = *usbdata;
 	kfree(usbdata);
 
@@ -394,7 +394,7 @@ int read_nic_word(struct net_device *dev
 	status = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
 				 RTL8187_REQ_GET_REGS, RTL8187_REQT_READ,
 				 (indx & 0xff) | 0xff00, (indx >> 8) & 0x0f,
-				 usbdata, 2, HZ / 2);
+				 usbdata, 2, 500);
 	*data = *usbdata;
 	kfree(usbdata);
 
@@ -418,7 +418,7 @@ static int read_nic_word_E(struct net_de
 
 	status = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
 				 RTL8187_REQ_GET_REGS, RTL8187_REQT_READ,
-				 indx | 0xfe00, 0, usbdata, 2, HZ / 2);
+				 indx | 0xfe00, 0, usbdata, 2, 500);
 	*data = *usbdata;
 	kfree(usbdata);
 
@@ -444,7 +444,7 @@ int read_nic_dword(struct net_device *de
 	status = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
 				 RTL8187_REQ_GET_REGS, RTL8187_REQT_READ,
 				 (indx & 0xff) | 0xff00, (indx >> 8) & 0x0f,
-				 usbdata, 4, HZ / 2);
+				 usbdata, 4, 500);
 	*data = *usbdata;
 	kfree(usbdata);
 

[PATCH 5.4 16/17] media: staging/intel-ipu3: css: Fix wrong size comparison imgu_css_fw_init

[Greg Kroah-Hartman]

From: Gustavo A. R. Silva <gustavoars@kernel.org>

commit a44f9d6f9dc1fb314a3f1ed2dcd4fbbcc3d9f892 upstream.

There is a wrong comparison of the total size of the loaded firmware
css->fw->size with the size of a pointer to struct imgu_fw_header.

Turn binary_header into a flexible-array member[1][2], use the
struct_size() helper and fix the wrong size comparison. Notice
that the loaded firmware needs to contain at least one 'struct
imgu_fw_info' item in the binary_header[] array.

It's also worth mentioning that

	"css->fw->size < struct_size(css->fwp, binary_header, 1)"

with binary_header declared as a flexible-array member is equivalent
to

	"css->fw->size < sizeof(struct imgu_fw_header)"

with binary_header declared as a one-element array (as in the original
code).

The replacement of the one-element array with a flexible-array member
also helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().

[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.10/process/deprecated.html#zero-length-and-one-element-arrays

Link: https://github.com/KSPP/linux/issues/79
Link: https://github.com/KSPP/linux/issues/109

Fixes: 09d290f0ba21 ("media: staging/intel-ipu3: css: Add support for firmware management")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/staging/media/ipu3/ipu3-css-fw.c |    7 +++----
 drivers/staging/media/ipu3/ipu3-css-fw.h |    2 +-
 2 files changed, 4 insertions(+), 5 deletions(-)

--- a/drivers/staging/media/ipu3/ipu3-css-fw.c
+++ b/drivers/staging/media/ipu3/ipu3-css-fw.c
@@ -124,12 +124,11 @@ int imgu_css_fw_init(struct imgu_css *cs
 	/* Check and display fw header info */
 
 	css->fwp = (struct imgu_fw_header *)css->fw->data;
-	if (css->fw->size < sizeof(struct imgu_fw_header *) ||
+	if (css->fw->size < struct_size(css->fwp, binary_header, 1) ||
 	    css->fwp->file_header.h_size != sizeof(struct imgu_fw_bi_file_h))
 		goto bad_fw;
-	if (sizeof(struct imgu_fw_bi_file_h) +
-	    css->fwp->file_header.binary_nr * sizeof(struct imgu_fw_info) >
-	    css->fw->size)
+	if (struct_size(css->fwp, binary_header,
+			css->fwp->file_header.binary_nr) > css->fw->size)
 		goto bad_fw;
 
 	dev_info(dev, "loaded firmware version %.64s, %u binaries, %zu bytes\n",
--- a/drivers/staging/media/ipu3/ipu3-css-fw.h
+++ b/drivers/staging/media/ipu3/ipu3-css-fw.h
@@ -170,7 +170,7 @@ struct imgu_fw_bi_file_h {
 
 struct imgu_fw_header {
 	struct imgu_fw_bi_file_h file_header;
-	struct imgu_fw_info binary_header[1];	/* binary_nr items */
+	struct imgu_fw_info binary_header[];	/* binary_nr items */
 };
 
 /******************* Firmware functions *******************/

[PATCH 5.4 17/17] rsi: fix control-message timeout

[Greg Kroah-Hartman]

From: Johan Hovold <johan@kernel.org>

commit 541fd20c3ce5b0bc39f0c6a52414b6b92416831c upstream.

USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.

Use the common control-message timeout define for the five-second
timeout.

Fixes: dad0d04fa7ba ("rsi: Add RS9113 wireless driver")
Cc: stable@vger.kernel.org      # 3.15
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211025120522.6045-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/wireless/rsi/rsi_91x_usb.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/net/wireless/rsi/rsi_91x_usb.c
+++ b/drivers/net/wireless/rsi/rsi_91x_usb.c
@@ -61,7 +61,7 @@ static int rsi_usb_card_write(struct rsi
 			      (void *)seg,
 			      (int)len,
 			      &transfer,
-			      HZ * 5);
+			      USB_CTRL_SET_TIMEOUT);
 
 	if (status < 0) {
 		rsi_dbg(ERR_ZONE,

Re: [PATCH 5.4 00/17] 5.4.159-rc1 review

[Florian Fainelli]

On 11/10/21 10:43 AM, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 5.4.159 release.
> There are 17 patches in this series, all will be posted as a response
> to this one.  If anyone has any issues with these being applied, please
> let me know.
> 
> Responses should be made by Fri, 12 Nov 2021 18:19:54 +0000.
> Anything received after that time might be too late.
> 
> The whole patch series can be found in one patch at:
> 	https://www.kernel.org/pub/linux/kernel/v5.x/stable-review/patch-5.4.159-rc1.gz
> or in the git tree and branch at:
> 	git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-5.4.y
> and the diffstat can be found below.
> 
> thanks,
> 
> greg k-h

On ARCH_BRCMSTB, using 32-bit and 64-bit ARM kernels:

Tested-by: Florian Fainelli <f.fainelli@gmail.com>
-- 
Florian

Re: [PATCH 5.4 00/17] 5.4.159-rc1 review

[Naresh Kamboju]

On Thu, 11 Nov 2021 at 00:17, Greg Kroah-Hartman
<gregkh@linuxfoundation.org> wrote:
>
> This is the start of the stable review cycle for the 5.4.159 release.
> There are 17 patches in this series, all will be posted as a response
> to this one.  If anyone has any issues with these being applied, please
> let me know.
>
> Responses should be made by Fri, 12 Nov 2021 18:19:54 +0000.
> Anything received after that time might be too late.
>
> The whole patch series can be found in one patch at:
>         https://www.kernel.org/pub/linux/kernel/v5.x/stable-review/patch-5.4.159-rc1.gz
> or in the git tree and branch at:
>         git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-5.4.y
> and the diffstat can be found below.
>
> thanks,
>
> greg k-h

Results from Linaro’s test farm.
No regressions on arm64, arm, x86_64, and i386.

Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>

## Build
* kernel: 5.4.159-rc1
* git: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git
* git branch: linux-5.4.y
* git commit: 1422b7f3f43d27856aa1eaf04eac12fc7e565f66
* git describe: v5.4.158-18-g1422b7f3f43d
* test details:
https://qa-reports.linaro.org/lkft/linux-stable-rc-linux-5.4.y/build/v5.4.158-18-g1422b7f3f43d

## No regressions (compared to v5.4.158)

## No fixes (compared to v5.4.158)

## Test result summary
total: 90024, pass: 74328, fail: 796, skip: 13498, xfail: 1402

## Build Summary
* arc: 10 total, 10 passed, 0 failed
* arm: 289 total, 267 passed, 22 failed
* arm64: 39 total, 39 passed, 0 failed
* dragonboard-410c: 1 total, 1 passed, 0 failed
* hi6220-hikey: 1 total, 1 passed, 0 failed
* i386: 20 total, 20 passed, 0 failed
* juno-r2: 1 total, 1 passed, 0 failed
* mips: 37 total, 37 passed, 0 failed
* parisc: 12 total, 12 passed, 0 failed
* powerpc: 54 total, 48 passed, 6 failed
* riscv: 24 total, 24 passed, 0 failed
* s390: 12 total, 12 passed, 0 failed
* sh: 24 total, 24 passed, 0 failed
* sparc: 12 total, 12 passed, 0 failed
* x15: 1 total, 1 passed, 0 failed
* x86: 1 total, 1 passed, 0 failed
* x86_64: 39 total, 39 passed, 0 failed

## Test suites summary
* fwts
* igt-gpu-tools
* kselftest-android
* kselftest-arm64
* kselftest-arm64/arm64.btitest.bti_c_func
* kselftest-arm64/arm64.btitest.bti_j_func
* kselftest-arm64/arm64.btitest.bti_jc_func
* kselftest-arm64/arm64.btitest.bti_none_func
* kselftest-arm64/arm64.btitest.nohint_func
* kselftest-arm64/arm64.btitest.paciasp_func
* kselftest-arm64/arm64.nobtitest.bti_c_func
* kselftest-arm64/arm64.nobtitest.bti_j_func
* kselftest-arm64/arm64.nobtitest.bti_jc_func
* kselftest-arm64/arm64.nobtitest.bti_none_func
* kselftest-arm64/arm64.nobtitest.nohint_func
* kselftest-arm64/arm64.nobtitest.paciasp_func
* kselftest-bpf
* kselftest-breakpoints
* kselftest-capabilities
* kselftest-cgroup
* kselftest-clone3
* kselftest-core
* kselftest-cpu-hotplug
* kselftest-cpufreq
* kselftest-drivers
* kselftest-efivarfs
* kselftest-filesystems
* kselftest-firmware
* kselftest-fpu
* kselftest-futex
* kselftest-gpio
* kselftest-intel_pstate
* kselftest-ipc
* kselftest-ir
* kselftest-kcmp
* kselftest-kexec
* kselftest-kvm
* kselftest-lib
* kselftest-livepatch
* kselftest-membarrier
* kselftest-memfd
* kselftest-memory-hotplug
* kselftest-mincore
* kselftest-mount
* kselftest-mqueue
* kselftest-net
* kselftest-netfilter
* kselftest-nsfs
* kselftest-openat2
* kselftest-pid_namespace
* kselftest-pidfd
* kselftest-proc
* kselftest-pstore
* kselftest-ptrace
* kselftest-rseq
* kselftest-rtc
* kselftest-seccomp
* kselftest-sigaltstack
* kselftest-size
* kselftest-splice
* kselftest-static_keys
* kselftest-sync
* kselftest-sysctl
* kselftest-tc-testing
* kselftest-timens
* kselftest-timers
* kselftest-tmpfs
* kselftest-tpm2
* kselftest-user
* kselftest-vm
* kselftest-x86
* kselftest-zram
* kvm-unit-tests
* libgpiod
* libhugetlbfs
* linux-log-parser
* ltp-cap_bounds-tests
* ltp-commands-tests
* ltp-containers-tests
* ltp-controllers-tests
* ltp-cpuhotplug-tests
* ltp-crypto-tests
* ltp-cve-tests
* ltp-dio-tests
* ltp-fcntl-locktests-tests
* ltp-filecaps-tests
* ltp-fs-tests
* ltp-fs_bind-tests
* ltp-fs_perms_simple-tests
* ltp-fsx-tests
* ltp-hugetlb-tests
* ltp-io-tests
* ltp-ipc-tests
* ltp-math-tests
* ltp-mm-tests
* ltp-nptl-tests
* ltp-open-posix-tests
* ltp-pty-tests
* ltp-sched-tests
* ltp-securebits-tests
* ltp-syscalls-tests
* ltp-tracing-tests
* network-basic-tests
* packetdrill
* perf
* prep-tmp-disk
* rcutorture
* ssuite
* v4l2-compliance

--
Linaro LKFT
https://lkft.linaro.org

Re: [PATCH 5.4 00/17] 5.4.159-rc1 review

[Sudip Mukherjee]

Hi Greg,

On Wed, Nov 10, 2021 at 07:43:39PM +0100, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 5.4.159 release.
> There are 17 patches in this series, all will be posted as a response
> to this one.  If anyone has any issues with these being applied, please
> let me know.
> 
> Responses should be made by Fri, 12 Nov 2021 18:19:54 +0000.
> Anything received after that time might be too late.

Build test:
mips (gcc version 11.2.1 20211104): 65 configs -> no new failure
arm (gcc version 11.2.1 20211104): 107 configs -> no new failure
arm64 (gcc version 11.2.1 20211104): 2 configs -> no failure
x86_64 (gcc version 11.2.1 20211104): 4 configs -> no failure

Boot test:
x86_64: Booted on my test laptop. No regression.
x86_64: Booted on qemu. No regression. [1]

[1]. https://openqa.qa.codethink.co.uk/tests/366


Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>

--
Regards
Sudip

Re: [PATCH 5.4 00/17] 5.4.159-rc1 review

[Shuah Khan]

On 11/10/21 11:43 AM, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 5.4.159 release.
> There are 17 patches in this series, all will be posted as a response
> to this one.  If anyone has any issues with these being applied, please
> let me know.
> 
> Responses should be made by Fri, 12 Nov 2021 18:19:54 +0000.
> Anything received after that time might be too late.
> 
> The whole patch series can be found in one patch at:
> 	https://www.kernel.org/pub/linux/kernel/v5.x/stable-review/patch-5.4.159-rc1.gz
> or in the git tree and branch at:
> 	git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-5.4.y
> and the diffstat can be found below.
> 
> thanks,
> 
> greg k-h
> 

Compiled and booted on my test system. No dmesg regressions.

Tested-by: Shuah Khan <skhan@linuxfoundation.org>

thanks,
-- Shuah

Re: [PATCH 5.4 00/17] 5.4.159-rc1 review

[Guenter Roeck]

On Wed, Nov 10, 2021 at 07:43:39PM +0100, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 5.4.159 release.
> There are 17 patches in this series, all will be posted as a response
> to this one.  If anyone has any issues with these being applied, please
> let me know.
> 
> Responses should be made by Fri, 12 Nov 2021 18:19:54 +0000.
> Anything received after that time might be too late.
> 

Build results:
	total: 157 pass: 157 fail: 0
Qemu test results:
	total: 446 pass: 446 fail: 0

Tested-by: Guenter Roeck <linux@roeck-us.net>

Guenter

Re: [PATCH 5.4 00/17] 5.4.159-rc1 review

[Jon Hunter]

On Wed, 10 Nov 2021 19:43:39 +0100, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 5.4.159 release.
> There are 17 patches in this series, all will be posted as a response
> to this one.  If anyone has any issues with these being applied, please
> let me know.
> 
> Responses should be made by Fri, 12 Nov 2021 18:19:54 +0000.
> Anything received after that time might be too late.
> 
> The whole patch series can be found in one patch at:
> 	https://www.kernel.org/pub/linux/kernel/v5.x/stable-review/patch-5.4.159-rc1.gz
> or in the git tree and branch at:
> 	git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-5.4.y
> and the diffstat can be found below.
> 
> thanks,
> 
> greg k-h

All tests passing for Tegra ...

Test results for stable-v5.4:
    10 builds:	10 pass, 0 fail
    26 boots:	26 pass, 0 fail
    59 tests:	59 pass, 0 fail

Linux version:	5.4.159-rc1-g1422b7f3f43d
Boards tested:	tegra124-jetson-tk1, tegra186-p2771-0000,
                tegra194-p2972-0000, tegra20-ventana,
                tegra210-p2371-2180, tegra210-p3450-0000,
                tegra30-cardhu-a04

Tested-by: Jon Hunter <jonathanh@nvidia.com>

Jon

Re: [PATCH 5.4 00/17] 5.4.159-rc1 review

[Samuel Zou]

On 2021/11/11 2:43, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 5.4.159 release.
> There are 17 patches in this series, all will be posted as a response
> to this one.  If anyone has any issues with these being applied, please
> let me know.
> 
> Responses should be made by Fri, 12 Nov 2021 18:19:54 +0000.
> Anything received after that time might be too late.
> 
> The whole patch series can be found in one patch at:
> 	https://www.kernel.org/pub/linux/kernel/v5.x/stable-review/patch-5.4.159-rc1.gz
> or in the git tree and branch at:
> 	git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-5.4.y
> and the diffstat can be found below.
> 
> thanks,
> 
> greg k-h
> 

Tested on arm64 and x86 for 5.4.159-rc1,

Kernel repo:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git
Branch: linux-5.4.y
Version: 5.4.159-rc1
Commit: 1422b7f3f43d27856aa1eaf04eac12fc7e565f66
Compiler: gcc version 7.3.0 (GCC)

arm64:
--------------------------------------------------------------------
Testcase Result Summary:
total: 8906
passed: 8906
failed: 0
timeout: 0
--------------------------------------------------------------------

x86:
--------------------------------------------------------------------
Testcase Result Summary:
total: 8906
passed: 8906
failed: 0
timeout: 0
--------------------------------------------------------------------

Tested-by: Hulk Robot <hulkrobot@huawei.com>