[PATCH v5 00/13] Add support for Airoha EN7523 SoC

[PATCH v5 00/13] Add support for Airoha EN7523 SoC

[Felix Fietkau]

This patchset adds support for the Airoha EN7523 SoC, intended primarily
for xPON/xDSL routers.

Felix Fietkau (3):
  clk: en7523: Add clock driver for Airoha EN7523 SoC
  PCI: mediatek: allow selecting controller driver for airoha arch
  ARM: dts: Add PCIe support for Airoha EN7523

John Crispin (10):
  dt-bindings: Add vendor prefix for Airoha
  dt-bindings: arm: airoha: Add binding for EN7523 SoC and EVB
  ARM: dts: Add basic support for Airoha EN7523
  ARM: Add basic support for Airoha EN7523 SoC
  ARM: multi_v7_defconfig: Add support for Airoha EN7523 SoC
  dt-bindings: Add en7523-scu device tree binding documentation
  dt-bindings: PCI: Add support for Airoha EN7532
  dt-bindings: arm: airoha: Add binding for Airoha GPIO controller
  gpio: Add support for Airoha EN7523 GPIO controller
  ARM: dts: add GPIO support for Airoha EN7523

 .../devicetree/bindings/arm/airoha.yaml       |  28 ++
 .../bindings/clock/airoha,en7523-scu.yaml     |  58 +++
 .../bindings/gpio/airoha,en7523-gpio.yaml     |  67 ++++
 .../devicetree/bindings/pci/mediatek-pcie.txt |   1 +
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 arch/arm/Kconfig                              |  12 +
 arch/arm/boot/dts/Makefile                    |   2 +
 arch/arm/boot/dts/en7523-evb.dts              |  43 +++
 arch/arm/boot/dts/en7523.dtsi                 | 202 ++++++++++
 arch/arm/configs/multi_v7_defconfig           |   1 +
 drivers/clk/Kconfig                           |   9 +
 drivers/clk/Makefile                          |   1 +
 drivers/clk/clk-en7523.c                      | 356 ++++++++++++++++++
 drivers/gpio/Kconfig                          |   9 +
 drivers/gpio/Makefile                         |   1 +
 drivers/gpio/gpio-en7523.c                    | 136 +++++++
 drivers/pci/controller/Kconfig                |   2 +-
 include/dt-bindings/clock/en7523-clk.h        |  17 +
 18 files changed, 946 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/arm/airoha.yaml
 create mode 100644 Documentation/devicetree/bindings/clock/airoha,en7523-scu.yaml
 create mode 100644 Documentation/devicetree/bindings/gpio/airoha,en7523-gpio.yaml
 create mode 100644 arch/arm/boot/dts/en7523-evb.dts
 create mode 100644 arch/arm/boot/dts/en7523.dtsi
 create mode 100644 drivers/clk/clk-en7523.c
 create mode 100644 drivers/gpio/gpio-en7523.c
 create mode 100644 include/dt-bindings/clock/en7523-clk.h

-- 
2.30.1


_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v5 00/13] Add support for Airoha EN7523 SoC

[Felix Fietkau]

This patchset adds support for the Airoha EN7523 SoC, intended primarily
for xPON/xDSL routers.

Felix Fietkau (3):
  clk: en7523: Add clock driver for Airoha EN7523 SoC
  PCI: mediatek: allow selecting controller driver for airoha arch
  ARM: dts: Add PCIe support for Airoha EN7523

John Crispin (10):
  dt-bindings: Add vendor prefix for Airoha
  dt-bindings: arm: airoha: Add binding for EN7523 SoC and EVB
  ARM: dts: Add basic support for Airoha EN7523
  ARM: Add basic support for Airoha EN7523 SoC
  ARM: multi_v7_defconfig: Add support for Airoha EN7523 SoC
  dt-bindings: Add en7523-scu device tree binding documentation
  dt-bindings: PCI: Add support for Airoha EN7532
  dt-bindings: arm: airoha: Add binding for Airoha GPIO controller
  gpio: Add support for Airoha EN7523 GPIO controller
  ARM: dts: add GPIO support for Airoha EN7523

 .../devicetree/bindings/arm/airoha.yaml       |  28 ++
 .../bindings/clock/airoha,en7523-scu.yaml     |  58 +++
 .../bindings/gpio/airoha,en7523-gpio.yaml     |  67 ++++
 .../devicetree/bindings/pci/mediatek-pcie.txt |   1 +
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 arch/arm/Kconfig                              |  12 +
 arch/arm/boot/dts/Makefile                    |   2 +
 arch/arm/boot/dts/en7523-evb.dts              |  43 +++
 arch/arm/boot/dts/en7523.dtsi                 | 202 ++++++++++
 arch/arm/configs/multi_v7_defconfig           |   1 +
 drivers/clk/Kconfig                           |   9 +
 drivers/clk/Makefile                          |   1 +
 drivers/clk/clk-en7523.c                      | 356 ++++++++++++++++++
 drivers/gpio/Kconfig                          |   9 +
 drivers/gpio/Makefile                         |   1 +
 drivers/gpio/gpio-en7523.c                    | 136 +++++++
 drivers/pci/controller/Kconfig                |   2 +-
 include/dt-bindings/clock/en7523-clk.h        |  17 +
 18 files changed, 946 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/arm/airoha.yaml
 create mode 100644 Documentation/devicetree/bindings/clock/airoha,en7523-scu.yaml
 create mode 100644 Documentation/devicetree/bindings/gpio/airoha,en7523-gpio.yaml
 create mode 100644 arch/arm/boot/dts/en7523-evb.dts
 create mode 100644 arch/arm/boot/dts/en7523.dtsi
 create mode 100644 drivers/clk/clk-en7523.c
 create mode 100644 drivers/gpio/gpio-en7523.c
 create mode 100644 include/dt-bindings/clock/en7523-clk.h

-- 
2.30.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 01/13] dt-bindings: Add vendor prefix for Airoha

[Felix Fietkau]

From: John Crispin <john@phrozen.org>

Add vendor prefix "airoha" for Airoha, a subsidiary of MediaTek

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Bert Vermeulen <bert@biot.com>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 66d6432fd781..025df36aee5f 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -59,6 +59,8 @@ patternProperties:
     description: Aeroflex Gaisler AB
   "^aesop,.*":
     description: AESOP Embedded Forum
+  "^airoha,.*":
+    description: Airoha
   "^al,.*":
     description: Annapurna Labs
   "^alcatel,.*":
-- 
2.30.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 01/13] dt-bindings: Add vendor prefix for Airoha

[Felix Fietkau]

From: John Crispin <john@phrozen.org>

Add vendor prefix "airoha" for Airoha, a subsidiary of MediaTek

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Bert Vermeulen <bert@biot.com>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 66d6432fd781..025df36aee5f 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -59,6 +59,8 @@ patternProperties:
     description: Aeroflex Gaisler AB
   "^aesop,.*":
     description: AESOP Embedded Forum
+  "^airoha,.*":
+    description: Airoha
   "^al,.*":
     description: Annapurna Labs
   "^alcatel,.*":
-- 
2.30.1

[PATCH v5 02/13] dt-bindings: arm: airoha: Add binding for EN7523 SoC and EVB

[Felix Fietkau]

From: John Crispin <john@phrozen.org>

Add devicetree binding for Airoha EN7523 SoC and evaluation board.

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Bert Vermeulen <bert@biot.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
 .../devicetree/bindings/arm/airoha.yaml       | 28 +++++++++++++++++++
 1 file changed, 28 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/airoha.yaml

diff --git a/Documentation/devicetree/bindings/arm/airoha.yaml b/Documentation/devicetree/bindings/arm/airoha.yaml
new file mode 100644
index 000000000000..fc19b1a6f37b
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/airoha.yaml
@@ -0,0 +1,28 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/arm/airoha.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Airoha SoC based Platforms Device Tree Bindings
+
+maintainers:
+  - Felix Fietkau <nbd@nbd.name>
+  - John Crispin <john@phrozen.org>
+
+description:
+  Boards with an Airoha SoC shall have the following properties.
+
+properties:
+  $nodename:
+    const: '/'
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - airoha,en7523-evb
+          - const: airoha,en7523
+
+additionalProperties: true
+
+...
-- 
2.30.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 02/13] dt-bindings: arm: airoha: Add binding for EN7523 SoC and EVB

[Felix Fietkau]

From: John Crispin <john@phrozen.org>

Add devicetree binding for Airoha EN7523 SoC and evaluation board.

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Bert Vermeulen <bert@biot.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
 .../devicetree/bindings/arm/airoha.yaml       | 28 +++++++++++++++++++
 1 file changed, 28 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/airoha.yaml

diff --git a/Documentation/devicetree/bindings/arm/airoha.yaml b/Documentation/devicetree/bindings/arm/airoha.yaml
new file mode 100644
index 000000000000..fc19b1a6f37b
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/airoha.yaml
@@ -0,0 +1,28 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/arm/airoha.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Airoha SoC based Platforms Device Tree Bindings
+
+maintainers:
+  - Felix Fietkau <nbd@nbd.name>
+  - John Crispin <john@phrozen.org>
+
+description:
+  Boards with an Airoha SoC shall have the following properties.
+
+properties:
+  $nodename:
+    const: '/'
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - airoha,en7523-evb
+          - const: airoha,en7523
+
+additionalProperties: true
+
+...
-- 
2.30.1

[PATCH v5 03/13] ARM: dts: Add basic support for Airoha EN7523

[Felix Fietkau]

From: John Crispin <john@phrozen.org>

Add basic support for Airoha EN7523, enough for booting to console.

The UART is basically 8250-compatible, except for the clock selection.
A clock-frequency value is synthesized to get this to run at 115200 bps.

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Bert Vermeulen <bert@biot.com>
---
 arch/arm/boot/dts/Makefile       |   2 +
 arch/arm/boot/dts/en7523-evb.dts |  27 ++++++++
 arch/arm/boot/dts/en7523.dtsi    | 114 +++++++++++++++++++++++++++++++
 3 files changed, 143 insertions(+)
 create mode 100644 arch/arm/boot/dts/en7523-evb.dts
 create mode 100644 arch/arm/boot/dts/en7523.dtsi

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 0de64f237cd8..81cb49f8d6fd 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -186,6 +186,8 @@ dtb-$(CONFIG_ARCH_DAVINCI) += \
 	da850-lego-ev3.dtb
 dtb-$(CONFIG_ARCH_DIGICOLOR) += \
 	cx92755_equinox.dtb
+dtb-$(CONFIG_ARCH_AIROHA) += \
+	en7523-evb.dtb
 dtb-$(CONFIG_ARCH_EXYNOS3) += \
 	exynos3250-artik5-eval.dtb \
 	exynos3250-monk.dtb \
diff --git a/arch/arm/boot/dts/en7523-evb.dts b/arch/arm/boot/dts/en7523-evb.dts
new file mode 100644
index 000000000000..69754ef9a628
--- /dev/null
+++ b/arch/arm/boot/dts/en7523-evb.dts
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/dts-v1/;
+
+/* Bootloader installs ATF here */
+/memreserve/ 0x80000000 0x200000;
+
+#include "en7523.dtsi"
+
+/ {
+	model = "Airoha EN7523 Evaluation Board";
+	compatible = "airoha,en7523-evb", "airoha,en7523";
+
+	aliases {
+		serial0 = &uart1;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlycon";
+		stdout-path = "serial0:115200n8";
+		linux,usable-memory-range = <0x80200000 0x1fe00000>;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/en7523.dtsi b/arch/arm/boot/dts/en7523.dtsi
new file mode 100644
index 000000000000..7e17311a3f90
--- /dev/null
+++ b/arch/arm/boot/dts/en7523.dtsi
@@ -0,0 +1,114 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		npu_binary@84000000 {
+			no-map;
+			reg = <0x84000000 0xA00000>;
+		};
+
+		npu_flag@84B0000 {
+			no-map;
+			reg = <0x84B00000 0x100000>;
+		};
+
+		npu_pkt@85000000 {
+			no-map;
+			reg = <0x85000000 0x1A00000>;
+		};
+
+		npu_phyaddr@86B00000 {
+			no-map;
+			reg = <0x86B00000 0x100000>;
+		};
+
+		npu_rxdesc@86D00000 {
+			no-map;
+			reg = <0x86D00000 0x100000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0>;
+			enable-method = "psci";
+			clock-frequency = <80000000>;
+			next-level-cache = <&L2_0>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x1>;
+			enable-method = "psci";
+			clock-frequency = <80000000>;
+			next-level-cache = <&L2_0>;
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	gic: interrupt-controller@9000000 {
+		compatible = "arm,gic-v3";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x09000000 0x20000>, <0x09080000 0x80000>;
+		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+		clock-frequency = <25000000>;
+	};
+
+	uart1: serial@1fbf0000 {
+		compatible = "ns16550";
+		reg = <0x1fbf0000 0x30>;
+		reg-io-width = <4>;
+		reg-shift = <2>;
+		interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+		clock-frequency = <1843200>;
+		status = "okay";
+	};
+};
-- 
2.30.1

[PATCH v5 03/13] ARM: dts: Add basic support for Airoha EN7523

[Felix Fietkau]

From: John Crispin <john@phrozen.org>

Add basic support for Airoha EN7523, enough for booting to console.

The UART is basically 8250-compatible, except for the clock selection.
A clock-frequency value is synthesized to get this to run at 115200 bps.

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Bert Vermeulen <bert@biot.com>
---
 arch/arm/boot/dts/Makefile       |   2 +
 arch/arm/boot/dts/en7523-evb.dts |  27 ++++++++
 arch/arm/boot/dts/en7523.dtsi    | 114 +++++++++++++++++++++++++++++++
 3 files changed, 143 insertions(+)
 create mode 100644 arch/arm/boot/dts/en7523-evb.dts
 create mode 100644 arch/arm/boot/dts/en7523.dtsi

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 0de64f237cd8..81cb49f8d6fd 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -186,6 +186,8 @@ dtb-$(CONFIG_ARCH_DAVINCI) += \
 	da850-lego-ev3.dtb
 dtb-$(CONFIG_ARCH_DIGICOLOR) += \
 	cx92755_equinox.dtb
+dtb-$(CONFIG_ARCH_AIROHA) += \
+	en7523-evb.dtb
 dtb-$(CONFIG_ARCH_EXYNOS3) += \
 	exynos3250-artik5-eval.dtb \
 	exynos3250-monk.dtb \
diff --git a/arch/arm/boot/dts/en7523-evb.dts b/arch/arm/boot/dts/en7523-evb.dts
new file mode 100644
index 000000000000..69754ef9a628
--- /dev/null
+++ b/arch/arm/boot/dts/en7523-evb.dts
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/dts-v1/;
+
+/* Bootloader installs ATF here */
+/memreserve/ 0x80000000 0x200000;
+
+#include "en7523.dtsi"
+
+/ {
+	model = "Airoha EN7523 Evaluation Board";
+	compatible = "airoha,en7523-evb", "airoha,en7523";
+
+	aliases {
+		serial0 = &uart1;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlycon";
+		stdout-path = "serial0:115200n8";
+		linux,usable-memory-range = <0x80200000 0x1fe00000>;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/en7523.dtsi b/arch/arm/boot/dts/en7523.dtsi
new file mode 100644
index 000000000000..7e17311a3f90
--- /dev/null
+++ b/arch/arm/boot/dts/en7523.dtsi
@@ -0,0 +1,114 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		npu_binary@84000000 {
+			no-map;
+			reg = <0x84000000 0xA00000>;
+		};
+
+		npu_flag@84B0000 {
+			no-map;
+			reg = <0x84B00000 0x100000>;
+		};
+
+		npu_pkt@85000000 {
+			no-map;
+			reg = <0x85000000 0x1A00000>;
+		};
+
+		npu_phyaddr@86B00000 {
+			no-map;
+			reg = <0x86B00000 0x100000>;
+		};
+
+		npu_rxdesc@86D00000 {
+			no-map;
+			reg = <0x86D00000 0x100000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0>;
+			enable-method = "psci";
+			clock-frequency = <80000000>;
+			next-level-cache = <&L2_0>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x1>;
+			enable-method = "psci";
+			clock-frequency = <80000000>;
+			next-level-cache = <&L2_0>;
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	gic: interrupt-controller@9000000 {
+		compatible = "arm,gic-v3";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x09000000 0x20000>, <0x09080000 0x80000>;
+		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+		clock-frequency = <25000000>;
+	};
+
+	uart1: serial@1fbf0000 {
+		compatible = "ns16550";
+		reg = <0x1fbf0000 0x30>;
+		reg-io-width = <4>;
+		reg-shift = <2>;
+		interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+		clock-frequency = <1843200>;
+		status = "okay";
+	};
+};
-- 
2.30.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 04/13] ARM: Add basic support for Airoha EN7523 SoC

[Felix Fietkau]

From: John Crispin <john@phrozen.org>

EN7523 is an armv8 based silicon used inside broadband access type devices
such as xPON and xDSL. It shares various silicon blocks with MediaTek
silicon such as the MT7622.

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Bert Vermeulen <bert@biot.com>
---
 arch/arm/Kconfig | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index f0f9e8bec83a..8dcd05ef31cc 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -573,6 +573,18 @@ config ARCH_VIRT
 	select HAVE_ARM_ARCH_TIMER
 	select ARCH_SUPPORTS_BIG_ENDIAN
 
+config ARCH_AIROHA
+	bool "Airoha SoC Support"
+	depends on ARCH_MULTI_V7
+	select ARM_AMBA
+	select ARM_GIC
+	select ARM_GIC_V3
+	select ARM_PSCI
+	select HAVE_ARM_ARCH_TIMER
+	select COMMON_CLK
+	help
+	  Support for Airoha EN7523 SoCs
+
 #
 # This is sorted alphabetically by mach-* pathname.  However, plat-*
 # Kconfigs may be included either alphabetically (according to the
-- 
2.30.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 04/13] ARM: Add basic support for Airoha EN7523 SoC

[Felix Fietkau]

From: John Crispin <john@phrozen.org>

EN7523 is an armv8 based silicon used inside broadband access type devices
such as xPON and xDSL. It shares various silicon blocks with MediaTek
silicon such as the MT7622.

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Bert Vermeulen <bert@biot.com>
---
 arch/arm/Kconfig | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index f0f9e8bec83a..8dcd05ef31cc 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -573,6 +573,18 @@ config ARCH_VIRT
 	select HAVE_ARM_ARCH_TIMER
 	select ARCH_SUPPORTS_BIG_ENDIAN
 
+config ARCH_AIROHA
+	bool "Airoha SoC Support"
+	depends on ARCH_MULTI_V7
+	select ARM_AMBA
+	select ARM_GIC
+	select ARM_GIC_V3
+	select ARM_PSCI
+	select HAVE_ARM_ARCH_TIMER
+	select COMMON_CLK
+	help
+	  Support for Airoha EN7523 SoCs
+
 #
 # This is sorted alphabetically by mach-* pathname.  However, plat-*
 # Kconfigs may be included either alphabetically (according to the
-- 
2.30.1

[PATCH v5 05/13] ARM: multi_v7_defconfig: Add support for Airoha EN7523 SoC

[Felix Fietkau]

From: John Crispin <john@phrozen.org>

This enables basic bootup support for the Airoha EN7523 SoC.

Signed-off-by: John Crispin <john@phrozen.org>
---
 arch/arm/configs/multi_v7_defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig
index c951aeed2138..912b3d60325b 100644
--- a/arch/arm/configs/multi_v7_defconfig
+++ b/arch/arm/configs/multi_v7_defconfig
@@ -32,6 +32,7 @@ CONFIG_MACH_BERLIN_BG2=y
 CONFIG_MACH_BERLIN_BG2CD=y
 CONFIG_MACH_BERLIN_BG2Q=y
 CONFIG_ARCH_DIGICOLOR=y
+CONFIG_ARCH_AIROHA=y
 CONFIG_ARCH_EXYNOS=y
 CONFIG_ARCH_HIGHBANK=y
 CONFIG_ARCH_HISI=y
-- 
2.30.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 05/13] ARM: multi_v7_defconfig: Add support for Airoha EN7523 SoC

[Felix Fietkau]

From: John Crispin <john@phrozen.org>

This enables basic bootup support for the Airoha EN7523 SoC.

Signed-off-by: John Crispin <john@phrozen.org>
---
 arch/arm/configs/multi_v7_defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig
index c951aeed2138..912b3d60325b 100644
--- a/arch/arm/configs/multi_v7_defconfig
+++ b/arch/arm/configs/multi_v7_defconfig
@@ -32,6 +32,7 @@ CONFIG_MACH_BERLIN_BG2=y
 CONFIG_MACH_BERLIN_BG2CD=y
 CONFIG_MACH_BERLIN_BG2Q=y
 CONFIG_ARCH_DIGICOLOR=y
+CONFIG_ARCH_AIROHA=y
 CONFIG_ARCH_EXYNOS=y
 CONFIG_ARCH_HIGHBANK=y
 CONFIG_ARCH_HISI=y
-- 
2.30.1

[PATCH v5 06/13] dt-bindings: Add en7523-scu device tree binding documentation

[Felix Fietkau]

From: John Crispin <john@phrozen.org>

Adds device tree binding documentation for clocks in the EN7523 SOC.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: John Crispin <john@phrozen.org>
---
 .../bindings/clock/airoha,en7523-scu.yaml     | 58 +++++++++++++++++++
 include/dt-bindings/clock/en7523-clk.h        | 17 ++++++
 2 files changed, 75 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/clock/airoha,en7523-scu.yaml
 create mode 100644 include/dt-bindings/clock/en7523-clk.h

diff --git a/Documentation/devicetree/bindings/clock/airoha,en7523-scu.yaml b/Documentation/devicetree/bindings/clock/airoha,en7523-scu.yaml
new file mode 100644
index 000000000000..79660f8126fa
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/airoha,en7523-scu.yaml
@@ -0,0 +1,58 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/airoha,en7523-scu.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: EN7523 Clock Device Tree Bindings
+
+maintainers:
+  - Felix Fietkau <nbd@nbd.name>
+  - John Crispin <nbd@nbd.name>
+
+description: |
+  This node defines the System Control Unit of the EN7523 SoC,
+  a collection of registers configuring many different aspects of the SoC.
+
+  The clock driver uses it to read and configure settings of the
+  PLL controller, which provides clocks for the CPU, the bus and
+  other SoC internal peripherals.
+
+  Each clock is assigned an identifier and client nodes use this identifier
+  to specify which clock they consume.
+
+  All these identifiers can be found in:
+  [1]: <include/dt-bindings/clock/en7523-clk.h>.
+
+  The clocks are provided inside a system controller node.
+
+properties:
+  compatible:
+    items:
+      - const: airoha,en7523-scu
+
+  reg:
+    maxItems: 2
+
+  "#clock-cells":
+    description:
+      The first cell indicates the clock number, see [1] for available
+      clocks.
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - '#clock-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/en7523-clk.h>
+    scu: scu@1fa20000 {
+      compatible = "airoha,en7523-scu";
+      reg = <0x1fa20000 0x400>,
+            <0x1fb00000 0x1000>;
+      #clock-cells = <1>;
+    };
diff --git a/include/dt-bindings/clock/en7523-clk.h b/include/dt-bindings/clock/en7523-clk.h
new file mode 100644
index 000000000000..717d23a5e5ae
--- /dev/null
+++ b/include/dt-bindings/clock/en7523-clk.h
@@ -0,0 +1,17 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+
+#ifndef _DT_BINDINGS_CLOCK_AIROHA_EN7523_H_
+#define _DT_BINDINGS_CLOCK_AIROHA_EN7523_H_
+
+#define EN7523_CLK_GSW		0
+#define EN7523_CLK_EMI		1
+#define EN7523_CLK_BUS		2
+#define EN7523_CLK_SLIC		3
+#define EN7523_CLK_SPI		4
+#define EN7523_CLK_NPU		5
+#define EN7523_CLK_CRYPTO	6
+#define EN7523_CLK_PCIE		7
+
+#define EN7523_NUM_CLOCKS	8
+
+#endif /* _DT_BINDINGS_CLOCK_AIROHA_EN7523_H_ */
-- 
2.30.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 06/13] dt-bindings: Add en7523-scu device tree binding documentation

[Felix Fietkau]

From: John Crispin <john@phrozen.org>

Adds device tree binding documentation for clocks in the EN7523 SOC.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: John Crispin <john@phrozen.org>
---
 .../bindings/clock/airoha,en7523-scu.yaml     | 58 +++++++++++++++++++
 include/dt-bindings/clock/en7523-clk.h        | 17 ++++++
 2 files changed, 75 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/clock/airoha,en7523-scu.yaml
 create mode 100644 include/dt-bindings/clock/en7523-clk.h

diff --git a/Documentation/devicetree/bindings/clock/airoha,en7523-scu.yaml b/Documentation/devicetree/bindings/clock/airoha,en7523-scu.yaml
new file mode 100644
index 000000000000..79660f8126fa
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/airoha,en7523-scu.yaml
@@ -0,0 +1,58 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/airoha,en7523-scu.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: EN7523 Clock Device Tree Bindings
+
+maintainers:
+  - Felix Fietkau <nbd@nbd.name>
+  - John Crispin <nbd@nbd.name>
+
+description: |
+  This node defines the System Control Unit of the EN7523 SoC,
+  a collection of registers configuring many different aspects of the SoC.
+
+  The clock driver uses it to read and configure settings of the
+  PLL controller, which provides clocks for the CPU, the bus and
+  other SoC internal peripherals.
+
+  Each clock is assigned an identifier and client nodes use this identifier
+  to specify which clock they consume.
+
+  All these identifiers can be found in:
+  [1]: <include/dt-bindings/clock/en7523-clk.h>.
+
+  The clocks are provided inside a system controller node.
+
+properties:
+  compatible:
+    items:
+      - const: airoha,en7523-scu
+
+  reg:
+    maxItems: 2
+
+  "#clock-cells":
+    description:
+      The first cell indicates the clock number, see [1] for available
+      clocks.
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - '#clock-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/en7523-clk.h>
+    scu: scu@1fa20000 {
+      compatible = "airoha,en7523-scu";
+      reg = <0x1fa20000 0x400>,
+            <0x1fb00000 0x1000>;
+      #clock-cells = <1>;
+    };
diff --git a/include/dt-bindings/clock/en7523-clk.h b/include/dt-bindings/clock/en7523-clk.h
new file mode 100644
index 000000000000..717d23a5e5ae
--- /dev/null
+++ b/include/dt-bindings/clock/en7523-clk.h
@@ -0,0 +1,17 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+
+#ifndef _DT_BINDINGS_CLOCK_AIROHA_EN7523_H_
+#define _DT_BINDINGS_CLOCK_AIROHA_EN7523_H_
+
+#define EN7523_CLK_GSW		0
+#define EN7523_CLK_EMI		1
+#define EN7523_CLK_BUS		2
+#define EN7523_CLK_SLIC		3
+#define EN7523_CLK_SPI		4
+#define EN7523_CLK_NPU		5
+#define EN7523_CLK_CRYPTO	6
+#define EN7523_CLK_PCIE		7
+
+#define EN7523_NUM_CLOCKS	8
+
+#endif /* _DT_BINDINGS_CLOCK_AIROHA_EN7523_H_ */
-- 
2.30.1

[PATCH v5 07/13] clk: en7523: Add clock driver for Airoha EN7523 SoC

[Felix Fietkau]

This driver only registers fixed rate clocks, since the clocks are fully
initialized by the boot loader and should not be changed later, according
to Airoha.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
 arch/arm/boot/dts/en7523.dtsi |   8 +
 drivers/clk/Kconfig           |   9 +
 drivers/clk/Makefile          |   1 +
 drivers/clk/clk-en7523.c      | 356 ++++++++++++++++++++++++++++++++++
 4 files changed, 374 insertions(+)
 create mode 100644 drivers/clk/clk-en7523.c

diff --git a/arch/arm/boot/dts/en7523.dtsi b/arch/arm/boot/dts/en7523.dtsi
index 7e17311a3f90..0148958c607b 100644
--- a/arch/arm/boot/dts/en7523.dtsi
+++ b/arch/arm/boot/dts/en7523.dtsi
@@ -2,6 +2,7 @@
 
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/en7523-clk.h>
 
 / {
 	interrupt-parent = <&gic>;
@@ -82,6 +83,13 @@ L2_0: l2-cache0 {
 		};
 	};
 
+	scu: scu@1fa20000 {
+		compatible = "airoha,en7523-scu";
+		reg = <0x1fa20000 0x400>,
+		      <0x1fb00000 0x1000>;
+		#clock-cells = <1>;
+	};
+
 	gic: interrupt-controller@9000000 {
 		compatible = "arm,gic-v3";
 		interrupt-controller;
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index c5b3dc97396a..b542f58c58d2 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -192,6 +192,15 @@ config COMMON_CLK_CS2000_CP
 	help
 	  If you say yes here you get support for the CS2000 clock multiplier.
 
+config COMMON_CLK_EN7523
+	bool "Clock driver for Airoha EN7523 SoC system clocks"
+	depends on OF
+	depends on ARCH_AIROHA || ARM || COMPILE_TEST
+	default ARCH_AIROHA
+	help
+	  This driver provides the fixed clocks and gates present on Airoha
+	  ARM silicon.
+
 config COMMON_CLK_FSL_FLEXSPI
 	tristate "Clock driver for FlexSPI on Layerscape SoCs"
 	depends on ARCH_LAYERSCAPE || COMPILE_TEST
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index e42312121e51..be11d88c1603 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -27,6 +27,7 @@ obj-$(CONFIG_COMMON_CLK_CDCE925)	+= clk-cdce925.o
 obj-$(CONFIG_ARCH_CLPS711X)		+= clk-clps711x.o
 obj-$(CONFIG_COMMON_CLK_CS2000_CP)	+= clk-cs2000-cp.o
 obj-$(CONFIG_ARCH_SPARX5)		+= clk-sparx5.o
+obj-$(CONFIG_COMMON_CLK_EN7523)		+= clk-en7523.o
 obj-$(CONFIG_COMMON_CLK_FIXED_MMIO)	+= clk-fixed-mmio.o
 obj-$(CONFIG_COMMON_CLK_FSL_FLEXSPI)	+= clk-fsl-flexspi.o
 obj-$(CONFIG_COMMON_CLK_FSL_SAI)	+= clk-fsl-sai.o
diff --git a/drivers/clk/clk-en7523.c b/drivers/clk/clk-en7523.c
new file mode 100644
index 000000000000..f1774a5bf537
--- /dev/null
+++ b/drivers/clk/clk-en7523.c
@@ -0,0 +1,356 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/regmap.h>
+#include <linux/clk-provider.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <dt-bindings/clock/en7523-clk.h>
+#include <linux/clk.h>
+
+#define REG_PCI_CONTROL			0x88
+#define   REG_PCI_CONTROL_PERSTOUT	BIT(29)
+#define   REG_PCI_CONTROL_PERSTOUT1	BIT(26)
+#define   REG_PCI_CONTROL_REFCLK_EN1	BIT(22)
+#define REG_GSW_CLK_DIV_SEL		0x1b4
+#define REG_EMI_CLK_DIV_SEL		0x1b8
+#define REG_BUS_CLK_DIV_SEL		0x1bc
+#define REG_SPI_CLK_DIV_SEL		0x1c4
+#define REG_SPI_CLK_FREQ_SEL		0x1c8
+#define REG_NPU_CLK_DIV_SEL		0x1fc
+#define REG_CRYPTO_CLKSRC		0x200
+#define REG_RESET_CONTROL		0x834
+#define   REG_RESET_CONTROL_PCIEHB	BIT(29)
+#define   REG_RESET_CONTROL_PCIE1	BIT(27)
+#define   REG_RESET_CONTROL_PCIE2	BIT(26)
+
+struct en_clk_desc {
+	int id;
+	const char *name;
+	u32 base_reg;
+	u32 base_bits;
+	u32 base_shift;
+	union {
+		const u32 *base_values;
+		u32 base_value;
+	};
+	int n_base_values;
+
+	u32 div_reg;
+	u32 div_bits;
+	u32 div_shift;
+	u32 div_val0;
+	u32 div_step;
+};
+
+struct en_clk_gate {
+	void __iomem *base;
+	struct clk_hw hw;
+};
+
+static const u32 gsw_base[] = { 400000000, 500000000 };
+static const u32 emi_base[] = { 333000000, 400000000 };
+static const u32 bus_base[] = { 500000000, 540000000 };
+static const u32 slic_base[] = { 100000000, 3125000 };
+static const u32 npu_base[] = { 333000000, 400000000, 500000000 };
+
+static const struct en_clk_desc en7523_base_clks[] = {
+	{
+		.id = EN7523_CLK_GSW,
+		.name = "gsw",
+
+		.base_reg = REG_GSW_CLK_DIV_SEL,
+		.base_bits = 1,
+		.base_shift = 8,
+		.base_values = gsw_base,
+		.n_base_values = ARRAY_SIZE(gsw_base),
+
+		.div_bits = 3,
+		.div_shift = 0,
+		.div_step = 1,
+	}, {
+		.id = EN7523_CLK_EMI,
+		.name = "emi",
+
+		.base_reg = REG_EMI_CLK_DIV_SEL,
+		.base_bits = 1,
+		.base_shift = 8,
+		.base_values = emi_base,
+		.n_base_values = ARRAY_SIZE(emi_base),
+
+		.div_bits = 3,
+		.div_shift = 0,
+		.div_step = 1,
+	}, {
+		.id = EN7523_CLK_BUS,
+		.name = "bus",
+
+		.base_reg = REG_BUS_CLK_DIV_SEL,
+		.base_bits = 1,
+		.base_shift = 8,
+		.base_values = bus_base,
+		.n_base_values = ARRAY_SIZE(bus_base),
+
+		.div_bits = 3,
+		.div_shift = 0,
+		.div_step = 1,
+	}, {
+		.id = EN7523_CLK_SLIC,
+		.name = "slic",
+
+		.base_reg = REG_SPI_CLK_FREQ_SEL,
+		.base_bits = 1,
+		.base_shift = 0,
+		.base_values = slic_base,
+		.n_base_values = ARRAY_SIZE(slic_base),
+
+		.div_reg = REG_SPI_CLK_DIV_SEL,
+		.div_bits = 5,
+		.div_shift = 24,
+		.div_val0 = 20,
+		.div_step = 2,
+	}, {
+		.id = EN7523_CLK_SPI,
+		.name = "spi",
+
+		.base_reg = REG_SPI_CLK_DIV_SEL,
+
+		.base_value = 400000000,
+
+		.div_bits = 5,
+		.div_shift = 8,
+		.div_val0 = 40,
+		.div_step = 2,
+	}, {
+		.id = EN7523_CLK_NPU,
+		.name = "npu",
+
+		.base_reg = REG_NPU_CLK_DIV_SEL,
+		.base_bits = 2,
+		.base_shift = 8,
+		.base_values = npu_base,
+		.n_base_values = ARRAY_SIZE(npu_base),
+
+		.div_bits = 3,
+		.div_shift = 0,
+		.div_step = 1,
+	}, {
+		.id = EN7523_CLK_CRYPTO,
+		.name = "crypto",
+
+		.base_reg = REG_CRYPTO_CLKSRC,
+		.base_bits = 1,
+		.base_shift = 8,
+		.base_values = emi_base,
+		.n_base_values = ARRAY_SIZE(emi_base),
+	}
+};
+
+static const struct of_device_id of_match_clk_en7523[] = {
+	{ .compatible = "airoha,en7523-scu", },
+	{ /* sentinel */ }
+};
+
+static u32 en7523_get_base_rate(void __iomem *base, int i)
+{
+	const struct en_clk_desc *desc = &en7523_base_clks[i];
+	u32 val;
+
+	if (!desc->base_bits)
+		return desc->base_value;
+
+	val = readl(base + desc->base_reg);
+	val >>= desc->base_shift;
+	val &= (1 << desc->base_bits) - 1;
+
+	if (val >= desc->n_base_values)
+		return 0;
+
+	return desc->base_values[val];
+}
+
+static u32 en7523_get_div(void __iomem *base, int i)
+{
+	const struct en_clk_desc *desc = &en7523_base_clks[i];
+	u32 reg, val;
+
+	if (!desc->div_bits)
+		return 1;
+
+	reg = desc->div_reg ? desc->div_reg : desc->base_reg;
+	val = readl(base + reg);
+	val >>= desc->div_shift;
+	val &= (1 << desc->div_bits) - 1;
+
+	if (!val && desc->div_val0)
+		return desc->div_val0;
+
+	return (val + 1) * desc->div_step;
+}
+
+static int en7523_pci_is_enabled(struct clk_hw *hw)
+{
+	struct en_clk_gate *cg = container_of(hw, struct en_clk_gate, hw);
+
+	return !!(readl(cg->base + REG_PCI_CONTROL) & REG_PCI_CONTROL_REFCLK_EN1);
+}
+
+static int en7523_pci_enable(struct clk_hw *hw)
+{
+	struct en_clk_gate *cg = container_of(hw, struct en_clk_gate, hw);
+	void *np_base = cg->base;
+	u32 val, mask;
+
+	/* Need to pull device low before reset */
+	val = readl(np_base + REG_PCI_CONTROL);
+	val &= ~(REG_PCI_CONTROL_PERSTOUT1 | REG_PCI_CONTROL_PERSTOUT);
+	writel(val, np_base + REG_PCI_CONTROL);
+	usleep_range(1000, 2000);
+
+	/* Enable PCIe port 1 */
+	val |= REG_PCI_CONTROL_REFCLK_EN1;
+	writel(val, np_base + REG_PCI_CONTROL);
+	usleep_range(1000, 2000);
+
+	/* Reset to default */
+	val = readl(np_base + REG_RESET_CONTROL);
+	mask = REG_RESET_CONTROL_PCIE1 | REG_RESET_CONTROL_PCIE2 |
+	       REG_RESET_CONTROL_PCIEHB;
+	writel(val & ~mask, np_base + REG_RESET_CONTROL);
+	usleep_range(1000, 2000);
+	writel(val | mask, np_base + REG_RESET_CONTROL);
+	msleep(100);
+	writel(val & ~mask, np_base + REG_RESET_CONTROL);
+	usleep_range(5000, 10000);
+
+	/* Release device */
+	mask = REG_PCI_CONTROL_PERSTOUT1 | REG_PCI_CONTROL_PERSTOUT;
+	val = readl(np_base + REG_PCI_CONTROL);
+	writel(val & ~mask, np_base + REG_PCI_CONTROL);
+	usleep_range(1000, 2000);
+	writel(val | mask, np_base + REG_PCI_CONTROL);
+	msleep(250);
+
+	return 0;
+}
+
+static void en7523_pci_disable(struct clk_hw *hw)
+{
+	struct en_clk_gate *cg = container_of(hw, struct en_clk_gate, hw);
+	void *np_base = cg->base;
+	u32 val;
+
+	val = readl(np_base + REG_PCI_CONTROL);
+	val &= ~REG_PCI_CONTROL_REFCLK_EN1;
+	writel(val, np_base + REG_PCI_CONTROL);
+}
+
+static struct clk *en7523_register_pcie_clk(struct device *dev,
+					    void __iomem *np_base)
+{
+	static const struct clk_ops pcie_gate_ops = {
+		.is_enabled = en7523_pci_is_enabled,
+		.enable = en7523_pci_enable,
+		.disable = en7523_pci_disable,
+	};
+	struct clk_init_data init = {
+		.name = "pcie",
+		.ops = &pcie_gate_ops,
+	};
+	struct en_clk_gate *cg;
+	struct clk *clk;
+
+	cg = devm_kzalloc(dev, sizeof(*cg), GFP_KERNEL);
+	if (!cg)
+		return NULL;
+
+	cg->base = np_base;
+	cg->hw.init = &init;
+	en7523_pci_disable(&cg->hw);
+
+	clk = clk_register(NULL, &cg->hw);
+	if (IS_ERR(clk))
+		clk = NULL;
+
+	return clk;
+}
+
+static void en7523_register_clocks(struct device *dev, struct clk_onecell_data *clk_data,
+				   void __iomem *base, void __iomem *np_base)
+{
+	struct clk *clk;
+	u32 rate;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(en7523_base_clks); i++) {
+		const struct en_clk_desc *desc = &en7523_base_clks[i];
+
+		rate = en7523_get_base_rate(base, i);
+		rate /= en7523_get_div(base, i);
+
+		clk = clk_register_fixed_rate(NULL, desc->name, NULL, 0, rate);
+		if (IS_ERR(clk)) {
+			pr_err("Failed to register clk %s: %ld\n",
+			       desc->name, PTR_ERR(clk));
+			continue;
+		}
+
+		clk_data->clks[desc->id] = clk;
+	}
+
+	clk = en7523_register_pcie_clk(dev, np_base);
+	clk_data->clks[EN7523_CLK_PCIE] = clk;
+
+	clk_data->clk_num = EN7523_NUM_CLOCKS;
+}
+
+static int en7523_clk_probe(struct platform_device *pdev)
+{
+	struct device_node *node = pdev->dev.of_node;
+	struct clk_onecell_data *clk_data;
+	void __iomem *base, *np_base;
+	int r;
+
+	base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	np_base = devm_platform_ioremap_resource(pdev, 1);
+	if (IS_ERR(base))
+		return PTR_ERR(np_base);
+
+	clk_data = devm_kzalloc(&pdev->dev, sizeof(*clk_data), GFP_KERNEL);
+	if (!clk_data)
+		return -ENOMEM;
+
+	clk_data->clks = devm_kcalloc(&pdev->dev, EN7523_NUM_CLOCKS,
+				      sizeof(*clk_data->clks), GFP_KERNEL);
+	if (!clk_data->clks)
+		return -ENOMEM;
+
+	en7523_register_clocks(&pdev->dev, clk_data, base, np_base);
+
+	r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data);
+	if (r)
+		dev_err(&pdev->dev,
+			"could not register clock provider: %s: %d\n",
+			pdev->name, r);
+
+	return r;
+}
+
+static struct platform_driver clk_en7523_drv = {
+	.probe = en7523_clk_probe,
+	.driver = {
+		.name = "clk-en7523",
+		.of_match_table = of_match_clk_en7523,
+	},
+};
+
+static int clk_en7523_init(void)
+{
+	return platform_driver_register(&clk_en7523_drv);
+}
+
+arch_initcall(clk_en7523_init);
-- 
2.30.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 07/13] clk: en7523: Add clock driver for Airoha EN7523 SoC

[Felix Fietkau]

This driver only registers fixed rate clocks, since the clocks are fully
initialized by the boot loader and should not be changed later, according
to Airoha.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
 arch/arm/boot/dts/en7523.dtsi |   8 +
 drivers/clk/Kconfig           |   9 +
 drivers/clk/Makefile          |   1 +
 drivers/clk/clk-en7523.c      | 356 ++++++++++++++++++++++++++++++++++
 4 files changed, 374 insertions(+)
 create mode 100644 drivers/clk/clk-en7523.c

diff --git a/arch/arm/boot/dts/en7523.dtsi b/arch/arm/boot/dts/en7523.dtsi
index 7e17311a3f90..0148958c607b 100644
--- a/arch/arm/boot/dts/en7523.dtsi
+++ b/arch/arm/boot/dts/en7523.dtsi
@@ -2,6 +2,7 @@
 
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/en7523-clk.h>
 
 / {
 	interrupt-parent = <&gic>;
@@ -82,6 +83,13 @@ L2_0: l2-cache0 {
 		};
 	};
 
+	scu: scu@1fa20000 {
+		compatible = "airoha,en7523-scu";
+		reg = <0x1fa20000 0x400>,
+		      <0x1fb00000 0x1000>;
+		#clock-cells = <1>;
+	};
+
 	gic: interrupt-controller@9000000 {
 		compatible = "arm,gic-v3";
 		interrupt-controller;
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index c5b3dc97396a..b542f58c58d2 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -192,6 +192,15 @@ config COMMON_CLK_CS2000_CP
 	help
 	  If you say yes here you get support for the CS2000 clock multiplier.
 
+config COMMON_CLK_EN7523
+	bool "Clock driver for Airoha EN7523 SoC system clocks"
+	depends on OF
+	depends on ARCH_AIROHA || ARM || COMPILE_TEST
+	default ARCH_AIROHA
+	help
+	  This driver provides the fixed clocks and gates present on Airoha
+	  ARM silicon.
+
 config COMMON_CLK_FSL_FLEXSPI
 	tristate "Clock driver for FlexSPI on Layerscape SoCs"
 	depends on ARCH_LAYERSCAPE || COMPILE_TEST
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index e42312121e51..be11d88c1603 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -27,6 +27,7 @@ obj-$(CONFIG_COMMON_CLK_CDCE925)	+= clk-cdce925.o
 obj-$(CONFIG_ARCH_CLPS711X)		+= clk-clps711x.o
 obj-$(CONFIG_COMMON_CLK_CS2000_CP)	+= clk-cs2000-cp.o
 obj-$(CONFIG_ARCH_SPARX5)		+= clk-sparx5.o
+obj-$(CONFIG_COMMON_CLK_EN7523)		+= clk-en7523.o
 obj-$(CONFIG_COMMON_CLK_FIXED_MMIO)	+= clk-fixed-mmio.o
 obj-$(CONFIG_COMMON_CLK_FSL_FLEXSPI)	+= clk-fsl-flexspi.o
 obj-$(CONFIG_COMMON_CLK_FSL_SAI)	+= clk-fsl-sai.o
diff --git a/drivers/clk/clk-en7523.c b/drivers/clk/clk-en7523.c
new file mode 100644
index 000000000000..f1774a5bf537
--- /dev/null
+++ b/drivers/clk/clk-en7523.c
@@ -0,0 +1,356 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/regmap.h>
+#include <linux/clk-provider.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <dt-bindings/clock/en7523-clk.h>
+#include <linux/clk.h>
+
+#define REG_PCI_CONTROL			0x88
+#define   REG_PCI_CONTROL_PERSTOUT	BIT(29)
+#define   REG_PCI_CONTROL_PERSTOUT1	BIT(26)
+#define   REG_PCI_CONTROL_REFCLK_EN1	BIT(22)
+#define REG_GSW_CLK_DIV_SEL		0x1b4
+#define REG_EMI_CLK_DIV_SEL		0x1b8
+#define REG_BUS_CLK_DIV_SEL		0x1bc
+#define REG_SPI_CLK_DIV_SEL		0x1c4
+#define REG_SPI_CLK_FREQ_SEL		0x1c8
+#define REG_NPU_CLK_DIV_SEL		0x1fc
+#define REG_CRYPTO_CLKSRC		0x200
+#define REG_RESET_CONTROL		0x834
+#define   REG_RESET_CONTROL_PCIEHB	BIT(29)
+#define   REG_RESET_CONTROL_PCIE1	BIT(27)
+#define   REG_RESET_CONTROL_PCIE2	BIT(26)
+
+struct en_clk_desc {
+	int id;
+	const char *name;
+	u32 base_reg;
+	u32 base_bits;
+	u32 base_shift;
+	union {
+		const u32 *base_values;
+		u32 base_value;
+	};
+	int n_base_values;
+
+	u32 div_reg;
+	u32 div_bits;
+	u32 div_shift;
+	u32 div_val0;
+	u32 div_step;
+};
+
+struct en_clk_gate {
+	void __iomem *base;
+	struct clk_hw hw;
+};
+
+static const u32 gsw_base[] = { 400000000, 500000000 };
+static const u32 emi_base[] = { 333000000, 400000000 };
+static const u32 bus_base[] = { 500000000, 540000000 };
+static const u32 slic_base[] = { 100000000, 3125000 };
+static const u32 npu_base[] = { 333000000, 400000000, 500000000 };
+
+static const struct en_clk_desc en7523_base_clks[] = {
+	{
+		.id = EN7523_CLK_GSW,
+		.name = "gsw",
+
+		.base_reg = REG_GSW_CLK_DIV_SEL,
+		.base_bits = 1,
+		.base_shift = 8,
+		.base_values = gsw_base,
+		.n_base_values = ARRAY_SIZE(gsw_base),
+
+		.div_bits = 3,
+		.div_shift = 0,
+		.div_step = 1,
+	}, {
+		.id = EN7523_CLK_EMI,
+		.name = "emi",
+
+		.base_reg = REG_EMI_CLK_DIV_SEL,
+		.base_bits = 1,
+		.base_shift = 8,
+		.base_values = emi_base,
+		.n_base_values = ARRAY_SIZE(emi_base),
+
+		.div_bits = 3,
+		.div_shift = 0,
+		.div_step = 1,
+	}, {
+		.id = EN7523_CLK_BUS,
+		.name = "bus",
+
+		.base_reg = REG_BUS_CLK_DIV_SEL,
+		.base_bits = 1,
+		.base_shift = 8,
+		.base_values = bus_base,
+		.n_base_values = ARRAY_SIZE(bus_base),
+
+		.div_bits = 3,
+		.div_shift = 0,
+		.div_step = 1,
+	}, {
+		.id = EN7523_CLK_SLIC,
+		.name = "slic",
+
+		.base_reg = REG_SPI_CLK_FREQ_SEL,
+		.base_bits = 1,
+		.base_shift = 0,
+		.base_values = slic_base,
+		.n_base_values = ARRAY_SIZE(slic_base),
+
+		.div_reg = REG_SPI_CLK_DIV_SEL,
+		.div_bits = 5,
+		.div_shift = 24,
+		.div_val0 = 20,
+		.div_step = 2,
+	}, {
+		.id = EN7523_CLK_SPI,
+		.name = "spi",
+
+		.base_reg = REG_SPI_CLK_DIV_SEL,
+
+		.base_value = 400000000,
+
+		.div_bits = 5,
+		.div_shift = 8,
+		.div_val0 = 40,
+		.div_step = 2,
+	}, {
+		.id = EN7523_CLK_NPU,
+		.name = "npu",
+
+		.base_reg = REG_NPU_CLK_DIV_SEL,
+		.base_bits = 2,
+		.base_shift = 8,
+		.base_values = npu_base,
+		.n_base_values = ARRAY_SIZE(npu_base),
+
+		.div_bits = 3,
+		.div_shift = 0,
+		.div_step = 1,
+	}, {
+		.id = EN7523_CLK_CRYPTO,
+		.name = "crypto",
+
+		.base_reg = REG_CRYPTO_CLKSRC,
+		.base_bits = 1,
+		.base_shift = 8,
+		.base_values = emi_base,
+		.n_base_values = ARRAY_SIZE(emi_base),
+	}
+};
+
+static const struct of_device_id of_match_clk_en7523[] = {
+	{ .compatible = "airoha,en7523-scu", },
+	{ /* sentinel */ }
+};
+
+static u32 en7523_get_base_rate(void __iomem *base, int i)
+{
+	const struct en_clk_desc *desc = &en7523_base_clks[i];
+	u32 val;
+
+	if (!desc->base_bits)
+		return desc->base_value;
+
+	val = readl(base + desc->base_reg);
+	val >>= desc->base_shift;
+	val &= (1 << desc->base_bits) - 1;
+
+	if (val >= desc->n_base_values)
+		return 0;
+
+	return desc->base_values[val];
+}
+
+static u32 en7523_get_div(void __iomem *base, int i)
+{
+	const struct en_clk_desc *desc = &en7523_base_clks[i];
+	u32 reg, val;
+
+	if (!desc->div_bits)
+		return 1;
+
+	reg = desc->div_reg ? desc->div_reg : desc->base_reg;
+	val = readl(base + reg);
+	val >>= desc->div_shift;
+	val &= (1 << desc->div_bits) - 1;
+
+	if (!val && desc->div_val0)
+		return desc->div_val0;
+
+	return (val + 1) * desc->div_step;
+}
+
+static int en7523_pci_is_enabled(struct clk_hw *hw)
+{
+	struct en_clk_gate *cg = container_of(hw, struct en_clk_gate, hw);
+
+	return !!(readl(cg->base + REG_PCI_CONTROL) & REG_PCI_CONTROL_REFCLK_EN1);
+}
+
+static int en7523_pci_enable(struct clk_hw *hw)
+{
+	struct en_clk_gate *cg = container_of(hw, struct en_clk_gate, hw);
+	void *np_base = cg->base;
+	u32 val, mask;
+
+	/* Need to pull device low before reset */
+	val = readl(np_base + REG_PCI_CONTROL);
+	val &= ~(REG_PCI_CONTROL_PERSTOUT1 | REG_PCI_CONTROL_PERSTOUT);
+	writel(val, np_base + REG_PCI_CONTROL);
+	usleep_range(1000, 2000);
+
+	/* Enable PCIe port 1 */
+	val |= REG_PCI_CONTROL_REFCLK_EN1;
+	writel(val, np_base + REG_PCI_CONTROL);
+	usleep_range(1000, 2000);
+
+	/* Reset to default */
+	val = readl(np_base + REG_RESET_CONTROL);
+	mask = REG_RESET_CONTROL_PCIE1 | REG_RESET_CONTROL_PCIE2 |
+	       REG_RESET_CONTROL_PCIEHB;
+	writel(val & ~mask, np_base + REG_RESET_CONTROL);
+	usleep_range(1000, 2000);
+	writel(val | mask, np_base + REG_RESET_CONTROL);
+	msleep(100);
+	writel(val & ~mask, np_base + REG_RESET_CONTROL);
+	usleep_range(5000, 10000);
+
+	/* Release device */
+	mask = REG_PCI_CONTROL_PERSTOUT1 | REG_PCI_CONTROL_PERSTOUT;
+	val = readl(np_base + REG_PCI_CONTROL);
+	writel(val & ~mask, np_base + REG_PCI_CONTROL);
+	usleep_range(1000, 2000);
+	writel(val | mask, np_base + REG_PCI_CONTROL);
+	msleep(250);
+
+	return 0;
+}
+
+static void en7523_pci_disable(struct clk_hw *hw)
+{
+	struct en_clk_gate *cg = container_of(hw, struct en_clk_gate, hw);
+	void *np_base = cg->base;
+	u32 val;
+
+	val = readl(np_base + REG_PCI_CONTROL);
+	val &= ~REG_PCI_CONTROL_REFCLK_EN1;
+	writel(val, np_base + REG_PCI_CONTROL);
+}
+
+static struct clk *en7523_register_pcie_clk(struct device *dev,
+					    void __iomem *np_base)
+{
+	static const struct clk_ops pcie_gate_ops = {
+		.is_enabled = en7523_pci_is_enabled,
+		.enable = en7523_pci_enable,
+		.disable = en7523_pci_disable,
+	};
+	struct clk_init_data init = {
+		.name = "pcie",
+		.ops = &pcie_gate_ops,
+	};
+	struct en_clk_gate *cg;
+	struct clk *clk;
+
+	cg = devm_kzalloc(dev, sizeof(*cg), GFP_KERNEL);
+	if (!cg)
+		return NULL;
+
+	cg->base = np_base;
+	cg->hw.init = &init;
+	en7523_pci_disable(&cg->hw);
+
+	clk = clk_register(NULL, &cg->hw);
+	if (IS_ERR(clk))
+		clk = NULL;
+
+	return clk;
+}
+
+static void en7523_register_clocks(struct device *dev, struct clk_onecell_data *clk_data,
+				   void __iomem *base, void __iomem *np_base)
+{
+	struct clk *clk;
+	u32 rate;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(en7523_base_clks); i++) {
+		const struct en_clk_desc *desc = &en7523_base_clks[i];
+
+		rate = en7523_get_base_rate(base, i);
+		rate /= en7523_get_div(base, i);
+
+		clk = clk_register_fixed_rate(NULL, desc->name, NULL, 0, rate);
+		if (IS_ERR(clk)) {
+			pr_err("Failed to register clk %s: %ld\n",
+			       desc->name, PTR_ERR(clk));
+			continue;
+		}
+
+		clk_data->clks[desc->id] = clk;
+	}
+
+	clk = en7523_register_pcie_clk(dev, np_base);
+	clk_data->clks[EN7523_CLK_PCIE] = clk;
+
+	clk_data->clk_num = EN7523_NUM_CLOCKS;
+}
+
+static int en7523_clk_probe(struct platform_device *pdev)
+{
+	struct device_node *node = pdev->dev.of_node;
+	struct clk_onecell_data *clk_data;
+	void __iomem *base, *np_base;
+	int r;
+
+	base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	np_base = devm_platform_ioremap_resource(pdev, 1);
+	if (IS_ERR(base))
+		return PTR_ERR(np_base);
+
+	clk_data = devm_kzalloc(&pdev->dev, sizeof(*clk_data), GFP_KERNEL);
+	if (!clk_data)
+		return -ENOMEM;
+
+	clk_data->clks = devm_kcalloc(&pdev->dev, EN7523_NUM_CLOCKS,
+				      sizeof(*clk_data->clks), GFP_KERNEL);
+	if (!clk_data->clks)
+		return -ENOMEM;
+
+	en7523_register_clocks(&pdev->dev, clk_data, base, np_base);
+
+	r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data);
+	if (r)
+		dev_err(&pdev->dev,
+			"could not register clock provider: %s: %d\n",
+			pdev->name, r);
+
+	return r;
+}
+
+static struct platform_driver clk_en7523_drv = {
+	.probe = en7523_clk_probe,
+	.driver = {
+		.name = "clk-en7523",
+		.of_match_table = of_match_clk_en7523,
+	},
+};
+
+static int clk_en7523_init(void)
+{
+	return platform_driver_register(&clk_en7523_drv);
+}
+
+arch_initcall(clk_en7523_init);
-- 
2.30.1

[PATCH v5 08/13] dt-bindings: PCI: Add support for Airoha EN7532

[Felix Fietkau]

From: John Crispin <john@phrozen.org>

EN7532 is an ARM based platform SoC integrating the same PCIe IP as
MT7622, add a binding for it.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: John Crispin <john@phrozen.org>
---
 Documentation/devicetree/bindings/pci/mediatek-pcie.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt
index 57ae73462272..684227522267 100644
--- a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt
@@ -7,6 +7,7 @@ Required properties:
 	"mediatek,mt7622-pcie"
 	"mediatek,mt7623-pcie"
 	"mediatek,mt7629-pcie"
+	"airoha,en7523-pcie"
 - device_type: Must be "pci"
 - reg: Base addresses and lengths of the root ports.
 - reg-names: Names of the above areas to use during resource lookup.
-- 
2.30.1


_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v5 08/13] dt-bindings: PCI: Add support for Airoha EN7532

[Felix Fietkau]

From: John Crispin <john@phrozen.org>

EN7532 is an ARM based platform SoC integrating the same PCIe IP as
MT7622, add a binding for it.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: John Crispin <john@phrozen.org>
---
 Documentation/devicetree/bindings/pci/mediatek-pcie.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt
index 57ae73462272..684227522267 100644
--- a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt
@@ -7,6 +7,7 @@ Required properties:
 	"mediatek,mt7622-pcie"
 	"mediatek,mt7623-pcie"
 	"mediatek,mt7629-pcie"
+	"airoha,en7523-pcie"
 - device_type: Must be "pci"
 - reg: Base addresses and lengths of the root ports.
 - reg-names: Names of the above areas to use during resource lookup.
-- 
2.30.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 08/13] dt-bindings: PCI: Add support for Airoha EN7532

[Felix Fietkau]

From: John Crispin <john@phrozen.org>

EN7532 is an ARM based platform SoC integrating the same PCIe IP as
MT7622, add a binding for it.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: John Crispin <john@phrozen.org>
---
 Documentation/devicetree/bindings/pci/mediatek-pcie.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt
index 57ae73462272..684227522267 100644
--- a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt
@@ -7,6 +7,7 @@ Required properties:
 	"mediatek,mt7622-pcie"
 	"mediatek,mt7623-pcie"
 	"mediatek,mt7629-pcie"
+	"airoha,en7523-pcie"
 - device_type: Must be "pci"
 - reg: Base addresses and lengths of the root ports.
 - reg-names: Names of the above areas to use during resource lookup.
-- 
2.30.1

[PATCH v5 09/13] PCI: mediatek: allow selecting controller driver for airoha arch

[Felix Fietkau]

The EN7523 SoC uses the same controller as MT7622

Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
 drivers/pci/controller/Kconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig
index 93b141110537..f1342059c2a3 100644
--- a/drivers/pci/controller/Kconfig
+++ b/drivers/pci/controller/Kconfig
@@ -233,7 +233,7 @@ config PCIE_ROCKCHIP_EP
 
 config PCIE_MEDIATEK
 	tristate "MediaTek PCIe controller"
-	depends on ARCH_MEDIATEK || COMPILE_TEST
+	depends on ARCH_AIROHA || ARCH_MEDIATEK || COMPILE_TEST
 	depends on OF
 	depends on PCI_MSI_IRQ_DOMAIN
 	help
-- 
2.30.1


_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v5 09/13] PCI: mediatek: allow selecting controller driver for airoha arch

[Felix Fietkau]

The EN7523 SoC uses the same controller as MT7622

Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
 drivers/pci/controller/Kconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig
index 93b141110537..f1342059c2a3 100644
--- a/drivers/pci/controller/Kconfig
+++ b/drivers/pci/controller/Kconfig
@@ -233,7 +233,7 @@ config PCIE_ROCKCHIP_EP
 
 config PCIE_MEDIATEK
 	tristate "MediaTek PCIe controller"
-	depends on ARCH_MEDIATEK || COMPILE_TEST
+	depends on ARCH_AIROHA || ARCH_MEDIATEK || COMPILE_TEST
 	depends on OF
 	depends on PCI_MSI_IRQ_DOMAIN
 	help
-- 
2.30.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 09/13] PCI: mediatek: allow selecting controller driver for airoha arch

[Felix Fietkau]

The EN7523 SoC uses the same controller as MT7622

Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
 drivers/pci/controller/Kconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig
index 93b141110537..f1342059c2a3 100644
--- a/drivers/pci/controller/Kconfig
+++ b/drivers/pci/controller/Kconfig
@@ -233,7 +233,7 @@ config PCIE_ROCKCHIP_EP
 
 config PCIE_MEDIATEK
 	tristate "MediaTek PCIe controller"
-	depends on ARCH_MEDIATEK || COMPILE_TEST
+	depends on ARCH_AIROHA || ARCH_MEDIATEK || COMPILE_TEST
 	depends on OF
 	depends on PCI_MSI_IRQ_DOMAIN
 	help
-- 
2.30.1

[PATCH v5 10/13] ARM: dts: Add PCIe support for Airoha EN7523

[Felix Fietkau]

This uses the MediaTek MT7622 PCIe driver, since the PCIe IP block is nearly
identical to the one in MT7622

Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
 arch/arm/boot/dts/en7523-evb.dts |  8 +++++
 arch/arm/boot/dts/en7523.dtsi    | 60 ++++++++++++++++++++++++++++++++
 2 files changed, 68 insertions(+)

diff --git a/arch/arm/boot/dts/en7523-evb.dts b/arch/arm/boot/dts/en7523-evb.dts
index 69754ef9a628..0a79f5f6c311 100644
--- a/arch/arm/boot/dts/en7523-evb.dts
+++ b/arch/arm/boot/dts/en7523-evb.dts
@@ -25,3 +25,11 @@ memory@80000000 {
 		reg = <0x80000000 0x20000000>;
 	};
 };
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/en7523.dtsi b/arch/arm/boot/dts/en7523.dtsi
index 0148958c607b..862da104d6f2 100644
--- a/arch/arm/boot/dts/en7523.dtsi
+++ b/arch/arm/boot/dts/en7523.dtsi
@@ -119,4 +119,64 @@ uart1: serial@1fbf0000 {
 		clock-frequency = <1843200>;
 		status = "okay";
 	};
+
+
+	pcie0: pcie@1fa91000 {
+		compatible = "airoha,en7523-pcie", "mediatek,mt7622-pcie";
+		device_type = "pci";
+		reg = <0x1fa91000 0x1000>;
+		reg-names = "port0";
+		linux,pci-domain = <0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "pcie_irq";
+		clocks = <&scu EN7523_CLK_PCIE>;
+		clock-names = "sys_ck0";
+		bus-range = <0x00 0xff>;
+		ranges = <0x82000000 0 0x20000000  0x20000000  0 0x8000000>;
+		status = "disabled";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie_intc0 0>,
+				<0 0 0 2 &pcie_intc0 1>,
+				<0 0 0 3 &pcie_intc0 2>,
+				<0 0 0 4 &pcie_intc0 3>;
+		pcie_intc0: interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+		};
+	};
+
+	pcie1: pcie@1fa92000 {
+		compatible = "airoha,en7523-pcie", "mediatek,mt7622-pcie";
+		device_type = "pci";
+		reg = <0x1fa92000 0x1000>;
+		reg-names = "port1";
+		linux,pci-domain = <1>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "pcie_irq";
+		clocks = <&scu EN7523_CLK_PCIE>;
+		clock-names = "sys_ck1";
+		bus-range = <0x00 0xff>;
+		ranges = <0x82000000 0 0x28000000  0x28000000  0 0x8000000>;
+		status = "disabled";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie_intc1 0>,
+				<0 0 0 2 &pcie_intc1 1>,
+				<0 0 0 3 &pcie_intc1 2>,
+				<0 0 0 4 &pcie_intc1 3>;
+		pcie_intc1: interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+		};
+	};
+
 };
-- 
2.30.1


_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v5 10/13] ARM: dts: Add PCIe support for Airoha EN7523

[Felix Fietkau]

This uses the MediaTek MT7622 PCIe driver, since the PCIe IP block is nearly
identical to the one in MT7622

Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
 arch/arm/boot/dts/en7523-evb.dts |  8 +++++
 arch/arm/boot/dts/en7523.dtsi    | 60 ++++++++++++++++++++++++++++++++
 2 files changed, 68 insertions(+)

diff --git a/arch/arm/boot/dts/en7523-evb.dts b/arch/arm/boot/dts/en7523-evb.dts
index 69754ef9a628..0a79f5f6c311 100644
--- a/arch/arm/boot/dts/en7523-evb.dts
+++ b/arch/arm/boot/dts/en7523-evb.dts
@@ -25,3 +25,11 @@ memory@80000000 {
 		reg = <0x80000000 0x20000000>;
 	};
 };
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/en7523.dtsi b/arch/arm/boot/dts/en7523.dtsi
index 0148958c607b..862da104d6f2 100644
--- a/arch/arm/boot/dts/en7523.dtsi
+++ b/arch/arm/boot/dts/en7523.dtsi
@@ -119,4 +119,64 @@ uart1: serial@1fbf0000 {
 		clock-frequency = <1843200>;
 		status = "okay";
 	};
+
+
+	pcie0: pcie@1fa91000 {
+		compatible = "airoha,en7523-pcie", "mediatek,mt7622-pcie";
+		device_type = "pci";
+		reg = <0x1fa91000 0x1000>;
+		reg-names = "port0";
+		linux,pci-domain = <0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "pcie_irq";
+		clocks = <&scu EN7523_CLK_PCIE>;
+		clock-names = "sys_ck0";
+		bus-range = <0x00 0xff>;
+		ranges = <0x82000000 0 0x20000000  0x20000000  0 0x8000000>;
+		status = "disabled";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie_intc0 0>,
+				<0 0 0 2 &pcie_intc0 1>,
+				<0 0 0 3 &pcie_intc0 2>,
+				<0 0 0 4 &pcie_intc0 3>;
+		pcie_intc0: interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+		};
+	};
+
+	pcie1: pcie@1fa92000 {
+		compatible = "airoha,en7523-pcie", "mediatek,mt7622-pcie";
+		device_type = "pci";
+		reg = <0x1fa92000 0x1000>;
+		reg-names = "port1";
+		linux,pci-domain = <1>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "pcie_irq";
+		clocks = <&scu EN7523_CLK_PCIE>;
+		clock-names = "sys_ck1";
+		bus-range = <0x00 0xff>;
+		ranges = <0x82000000 0 0x28000000  0x28000000  0 0x8000000>;
+		status = "disabled";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie_intc1 0>,
+				<0 0 0 2 &pcie_intc1 1>,
+				<0 0 0 3 &pcie_intc1 2>,
+				<0 0 0 4 &pcie_intc1 3>;
+		pcie_intc1: interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+		};
+	};
+
 };
-- 
2.30.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 10/13] ARM: dts: Add PCIe support for Airoha EN7523

[Felix Fietkau]

This uses the MediaTek MT7622 PCIe driver, since the PCIe IP block is nearly
identical to the one in MT7622

Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
 arch/arm/boot/dts/en7523-evb.dts |  8 +++++
 arch/arm/boot/dts/en7523.dtsi    | 60 ++++++++++++++++++++++++++++++++
 2 files changed, 68 insertions(+)

diff --git a/arch/arm/boot/dts/en7523-evb.dts b/arch/arm/boot/dts/en7523-evb.dts
index 69754ef9a628..0a79f5f6c311 100644
--- a/arch/arm/boot/dts/en7523-evb.dts
+++ b/arch/arm/boot/dts/en7523-evb.dts
@@ -25,3 +25,11 @@ memory@80000000 {
 		reg = <0x80000000 0x20000000>;
 	};
 };
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/en7523.dtsi b/arch/arm/boot/dts/en7523.dtsi
index 0148958c607b..862da104d6f2 100644
--- a/arch/arm/boot/dts/en7523.dtsi
+++ b/arch/arm/boot/dts/en7523.dtsi
@@ -119,4 +119,64 @@ uart1: serial@1fbf0000 {
 		clock-frequency = <1843200>;
 		status = "okay";
 	};
+
+
+	pcie0: pcie@1fa91000 {
+		compatible = "airoha,en7523-pcie", "mediatek,mt7622-pcie";
+		device_type = "pci";
+		reg = <0x1fa91000 0x1000>;
+		reg-names = "port0";
+		linux,pci-domain = <0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "pcie_irq";
+		clocks = <&scu EN7523_CLK_PCIE>;
+		clock-names = "sys_ck0";
+		bus-range = <0x00 0xff>;
+		ranges = <0x82000000 0 0x20000000  0x20000000  0 0x8000000>;
+		status = "disabled";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie_intc0 0>,
+				<0 0 0 2 &pcie_intc0 1>,
+				<0 0 0 3 &pcie_intc0 2>,
+				<0 0 0 4 &pcie_intc0 3>;
+		pcie_intc0: interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+		};
+	};
+
+	pcie1: pcie@1fa92000 {
+		compatible = "airoha,en7523-pcie", "mediatek,mt7622-pcie";
+		device_type = "pci";
+		reg = <0x1fa92000 0x1000>;
+		reg-names = "port1";
+		linux,pci-domain = <1>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "pcie_irq";
+		clocks = <&scu EN7523_CLK_PCIE>;
+		clock-names = "sys_ck1";
+		bus-range = <0x00 0xff>;
+		ranges = <0x82000000 0 0x28000000  0x28000000  0 0x8000000>;
+		status = "disabled";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie_intc1 0>,
+				<0 0 0 2 &pcie_intc1 1>,
+				<0 0 0 3 &pcie_intc1 2>,
+				<0 0 0 4 &pcie_intc1 3>;
+		pcie_intc1: interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+		};
+	};
+
 };
-- 
2.30.1

[PATCH v5 11/13] dt-bindings: arm: airoha: Add binding for Airoha GPIO controller

[Felix Fietkau]

From: John Crispin <john@phrozen.org>

Airoha's GPIO controller on their ARM EN7523 SoCs consists of two banks of 32
GPIOs

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
 .../bindings/gpio/airoha,en7523-gpio.yaml     | 67 +++++++++++++++++++
 1 file changed, 67 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/gpio/airoha,en7523-gpio.yaml

diff --git a/Documentation/devicetree/bindings/gpio/airoha,en7523-gpio.yaml b/Documentation/devicetree/bindings/gpio/airoha,en7523-gpio.yaml
new file mode 100644
index 000000000000..66c00ec85731
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/airoha,en7523-gpio.yaml
@@ -0,0 +1,67 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/airoha,en7523-gpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Airoha EN7523 GPIO controller
+
+maintainers:
+  - John Crispin <john@phrozen.org>
+
+description: |
+  Airoha's GPIO controller on their ARM EN7523 SoCs consists of two banks of 32
+  GPIOs.
+
+properties:
+  $nodename:
+    pattern: "^gpio@[0-9a-f]+$"
+
+  compatible:
+    items:
+      - const: airoha,en7523-gpio
+
+  reg:
+    description: |
+      The first tuple points to the input register.
+      The second and third tuple point to the direction registers
+      The fourth tuple points to the output register
+    maxItems: 4
+
+  "#gpio-cells":
+    const: 2
+
+  gpio-controller: true
+
+required:
+  - compatible
+  - reg
+  - "#gpio-cells"
+  - gpio-controller
+
+additionalProperties: false
+
+examples:
+  - |
+    gpio0: gpio@1fbf0200 {
+        compatible = "airoha,en7523-gpio";
+        reg = <0x1fbf0204 0x4>,
+              <0x1fbf0200 0x4>,
+              <0x1fbf0220 0x4>,
+              <0x1fbf0214 0x4>;
+        gpio-controller;
+        #gpio-cells = <2>;
+    };
+
+    gpio1: gpio@1fbf0270 {
+        compatible = "airoha,en7523-gpio";
+        reg = <0x1fbf0270 0x4>,
+              <0x1fbf0260 0x4>,
+              <0x1fbf0264 0x4>,
+              <0x1fbf0278 0x4>;
+        gpio-controller;
+        #gpio-cells = <2>;
+    };
+
+
+...
-- 
2.30.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 11/13] dt-bindings: arm: airoha: Add binding for Airoha GPIO controller

[Felix Fietkau]

From: John Crispin <john@phrozen.org>

Airoha's GPIO controller on their ARM EN7523 SoCs consists of two banks of 32
GPIOs

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
 .../bindings/gpio/airoha,en7523-gpio.yaml     | 67 +++++++++++++++++++
 1 file changed, 67 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/gpio/airoha,en7523-gpio.yaml

diff --git a/Documentation/devicetree/bindings/gpio/airoha,en7523-gpio.yaml b/Documentation/devicetree/bindings/gpio/airoha,en7523-gpio.yaml
new file mode 100644
index 000000000000..66c00ec85731
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/airoha,en7523-gpio.yaml
@@ -0,0 +1,67 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/airoha,en7523-gpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Airoha EN7523 GPIO controller
+
+maintainers:
+  - John Crispin <john@phrozen.org>
+
+description: |
+  Airoha's GPIO controller on their ARM EN7523 SoCs consists of two banks of 32
+  GPIOs.
+
+properties:
+  $nodename:
+    pattern: "^gpio@[0-9a-f]+$"
+
+  compatible:
+    items:
+      - const: airoha,en7523-gpio
+
+  reg:
+    description: |
+      The first tuple points to the input register.
+      The second and third tuple point to the direction registers
+      The fourth tuple points to the output register
+    maxItems: 4
+
+  "#gpio-cells":
+    const: 2
+
+  gpio-controller: true
+
+required:
+  - compatible
+  - reg
+  - "#gpio-cells"
+  - gpio-controller
+
+additionalProperties: false
+
+examples:
+  - |
+    gpio0: gpio@1fbf0200 {
+        compatible = "airoha,en7523-gpio";
+        reg = <0x1fbf0204 0x4>,
+              <0x1fbf0200 0x4>,
+              <0x1fbf0220 0x4>,
+              <0x1fbf0214 0x4>;
+        gpio-controller;
+        #gpio-cells = <2>;
+    };
+
+    gpio1: gpio@1fbf0270 {
+        compatible = "airoha,en7523-gpio";
+        reg = <0x1fbf0270 0x4>,
+              <0x1fbf0260 0x4>,
+              <0x1fbf0264 0x4>,
+              <0x1fbf0278 0x4>;
+        gpio-controller;
+        #gpio-cells = <2>;
+    };
+
+
+...
-- 
2.30.1

[PATCH v5 12/13] gpio: Add support for Airoha EN7523 GPIO controller

[Felix Fietkau]

From: John Crispin <john@phrozen.org>

Airoha's GPIO controller on their ARM EN7523 SoCs consists of two banks of 32
GPIOs. Each instance in DT is for an single bank.

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
 drivers/gpio/Kconfig       |   9 +++
 drivers/gpio/Makefile      |   1 +
 drivers/gpio/gpio-en7523.c | 136 +++++++++++++++++++++++++++++++++++++
 3 files changed, 146 insertions(+)
 create mode 100644 drivers/gpio/gpio-en7523.c

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 072ed610f9c6..e4a34272504f 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -247,6 +247,15 @@ config GPIO_EM
 	help
 	  Say yes here to support GPIO on Renesas Emma Mobile SoCs.
 
+config GPIO_EN7523
+	tristate "Airoha GPIO support"
+	depends on ARCH_AIROHA
+	default ARCH_AIROHA
+	select GPIO_GENERIC
+	select GPIOLIB_IRQCHIP
+	help
+	  Say yes here to support the GPIO controller on Airoha EN7523.
+
 config GPIO_EP93XX
 	def_bool y
 	depends on ARCH_EP93XX
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 71ee9fc2ff83..d2269ee0948e 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -56,6 +56,7 @@ obj-$(CONFIG_GPIO_DLN2)			+= gpio-dln2.o
 obj-$(CONFIG_GPIO_DWAPB)		+= gpio-dwapb.o
 obj-$(CONFIG_GPIO_EIC_SPRD)		+= gpio-eic-sprd.o
 obj-$(CONFIG_GPIO_EM)			+= gpio-em.o
+obj-$(CONFIG_GPIO_EN7523)		+= gpio-en7523.o
 obj-$(CONFIG_GPIO_EP93XX)		+= gpio-ep93xx.o
 obj-$(CONFIG_GPIO_EXAR)			+= gpio-exar.o
 obj-$(CONFIG_GPIO_F7188X)		+= gpio-f7188x.o
diff --git a/drivers/gpio/gpio-en7523.c b/drivers/gpio/gpio-en7523.c
new file mode 100644
index 000000000000..0032f99e366d
--- /dev/null
+++ b/drivers/gpio/gpio-en7523.c
@@ -0,0 +1,136 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/gpio/driver.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+
+#define AIROHA_GPIO_MAX		32
+
+/**
+ * airoha_gpio_ctrl - Airoha GPIO driver data
+ *
+ * @gc: Associated gpio_chip instance.
+ * @data: The data register.
+ * @dir0: The direction register for the lower 16 pins.
+ * @dir1: The direction register for the higher 16 pins.
+ * @output: The output enable register.
+ */
+struct airoha_gpio_ctrl {
+	struct gpio_chip gc;
+	void __iomem *data;
+	void __iomem *dir[2];
+	void __iomem *output;
+};
+
+static struct airoha_gpio_ctrl *gc_to_ctrl(struct gpio_chip *gc)
+{
+	return container_of(gc, struct airoha_gpio_ctrl, gc);
+}
+
+static int airoha_dir_set(struct gpio_chip *gc, unsigned int gpio,
+			  int val, int out)
+{
+	struct airoha_gpio_ctrl *ctrl = gc_to_ctrl(gc);
+	u32 dir = ioread32(ctrl->dir[gpio / 16]);
+	u32 output = ioread32(ctrl->output);
+	u32 mask = BIT((gpio % 16) * 2);
+
+	if (out) {
+		dir |= mask;
+		output |= BIT(gpio);
+	} else {
+		dir &= ~mask;
+		output &= ~BIT(gpio);
+	}
+
+	iowrite32(dir, ctrl->dir[gpio / 16]);
+	iowrite32(output, ctrl->output);
+
+	if (out)
+		gc->set(gc, gpio, val);
+
+	return 0;
+}
+
+static int airoha_dir_out(struct gpio_chip *gc, unsigned int gpio,
+			  int val)
+{
+	return airoha_dir_set(gc, gpio, val, 1);
+}
+
+static int airoha_dir_in(struct gpio_chip *gc, unsigned int gpio)
+{
+	return airoha_dir_set(gc, gpio, 0, 0);
+}
+
+static int airoha_get_dir(struct gpio_chip *gc, unsigned int gpio)
+{
+	struct airoha_gpio_ctrl *ctrl = gc_to_ctrl(gc);
+	u32 dir = ioread32(ctrl->dir[gpio / 16]);
+	u32 mask = BIT((gpio % 16) * 2);
+
+	return dir & mask;
+}
+
+static const struct of_device_id airoha_gpio_of_match[] = {
+	{ .compatible = "airoha,en7523-gpio" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, airoha_gpio_of_match);
+
+static int airoha_gpio_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct airoha_gpio_ctrl *ctrl;
+	int err;
+
+	ctrl = devm_kzalloc(dev, sizeof(*ctrl), GFP_KERNEL);
+	if (!ctrl)
+		return -ENOMEM;
+
+	ctrl->data = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(ctrl->data))
+		return PTR_ERR(ctrl->data);
+
+	ctrl->dir[0] = devm_platform_ioremap_resource(pdev, 1);
+	if (IS_ERR(ctrl->dir[0]))
+		return PTR_ERR(ctrl->dir[0]);
+
+	ctrl->dir[1] = devm_platform_ioremap_resource(pdev, 2);
+	if (IS_ERR(ctrl->dir[1]))
+		return PTR_ERR(ctrl->dir[1]);
+
+	ctrl->output = devm_platform_ioremap_resource(pdev, 3);
+	if (IS_ERR(ctrl->output))
+		return PTR_ERR(ctrl->output);
+
+	err = bgpio_init(&ctrl->gc, dev, 4, ctrl->data, NULL,
+			 NULL, NULL, NULL, 0);
+	if (err) {
+		dev_err(dev, "unable to init generic GPIO");
+		return err;
+	}
+
+	ctrl->gc.ngpio = AIROHA_GPIO_MAX;
+	ctrl->gc.owner = THIS_MODULE;
+	ctrl->gc.direction_output = airoha_dir_out;
+	ctrl->gc.direction_input = airoha_dir_in;
+	ctrl->gc.get_direction = airoha_get_dir;
+
+	return devm_gpiochip_add_data(dev, &ctrl->gc, ctrl);
+}
+
+static struct platform_driver airoha_gpio_driver = {
+	.driver = {
+		.name = "airoha-gpio",
+		.of_match_table	= airoha_gpio_of_match,
+	},
+	.probe = airoha_gpio_probe,
+};
+module_platform_driver(airoha_gpio_driver);
+
+MODULE_DESCRIPTION("Airoha GPIO support");
+MODULE_AUTHOR("John Crispin <john@phrozen.org>");
+MODULE_LICENSE("GPL v2");
-- 
2.30.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 12/13] gpio: Add support for Airoha EN7523 GPIO controller

[Felix Fietkau]

From: John Crispin <john@phrozen.org>

Airoha's GPIO controller on their ARM EN7523 SoCs consists of two banks of 32
GPIOs. Each instance in DT is for an single bank.

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
 drivers/gpio/Kconfig       |   9 +++
 drivers/gpio/Makefile      |   1 +
 drivers/gpio/gpio-en7523.c | 136 +++++++++++++++++++++++++++++++++++++
 3 files changed, 146 insertions(+)
 create mode 100644 drivers/gpio/gpio-en7523.c

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 072ed610f9c6..e4a34272504f 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -247,6 +247,15 @@ config GPIO_EM
 	help
 	  Say yes here to support GPIO on Renesas Emma Mobile SoCs.
 
+config GPIO_EN7523
+	tristate "Airoha GPIO support"
+	depends on ARCH_AIROHA
+	default ARCH_AIROHA
+	select GPIO_GENERIC
+	select GPIOLIB_IRQCHIP
+	help
+	  Say yes here to support the GPIO controller on Airoha EN7523.
+
 config GPIO_EP93XX
 	def_bool y
 	depends on ARCH_EP93XX
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 71ee9fc2ff83..d2269ee0948e 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -56,6 +56,7 @@ obj-$(CONFIG_GPIO_DLN2)			+= gpio-dln2.o
 obj-$(CONFIG_GPIO_DWAPB)		+= gpio-dwapb.o
 obj-$(CONFIG_GPIO_EIC_SPRD)		+= gpio-eic-sprd.o
 obj-$(CONFIG_GPIO_EM)			+= gpio-em.o
+obj-$(CONFIG_GPIO_EN7523)		+= gpio-en7523.o
 obj-$(CONFIG_GPIO_EP93XX)		+= gpio-ep93xx.o
 obj-$(CONFIG_GPIO_EXAR)			+= gpio-exar.o
 obj-$(CONFIG_GPIO_F7188X)		+= gpio-f7188x.o
diff --git a/drivers/gpio/gpio-en7523.c b/drivers/gpio/gpio-en7523.c
new file mode 100644
index 000000000000..0032f99e366d
--- /dev/null
+++ b/drivers/gpio/gpio-en7523.c
@@ -0,0 +1,136 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/gpio/driver.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+
+#define AIROHA_GPIO_MAX		32
+
+/**
+ * airoha_gpio_ctrl - Airoha GPIO driver data
+ *
+ * @gc: Associated gpio_chip instance.
+ * @data: The data register.
+ * @dir0: The direction register for the lower 16 pins.
+ * @dir1: The direction register for the higher 16 pins.
+ * @output: The output enable register.
+ */
+struct airoha_gpio_ctrl {
+	struct gpio_chip gc;
+	void __iomem *data;
+	void __iomem *dir[2];
+	void __iomem *output;
+};
+
+static struct airoha_gpio_ctrl *gc_to_ctrl(struct gpio_chip *gc)
+{
+	return container_of(gc, struct airoha_gpio_ctrl, gc);
+}
+
+static int airoha_dir_set(struct gpio_chip *gc, unsigned int gpio,
+			  int val, int out)
+{
+	struct airoha_gpio_ctrl *ctrl = gc_to_ctrl(gc);
+	u32 dir = ioread32(ctrl->dir[gpio / 16]);
+	u32 output = ioread32(ctrl->output);
+	u32 mask = BIT((gpio % 16) * 2);
+
+	if (out) {
+		dir |= mask;
+		output |= BIT(gpio);
+	} else {
+		dir &= ~mask;
+		output &= ~BIT(gpio);
+	}
+
+	iowrite32(dir, ctrl->dir[gpio / 16]);
+	iowrite32(output, ctrl->output);
+
+	if (out)
+		gc->set(gc, gpio, val);
+
+	return 0;
+}
+
+static int airoha_dir_out(struct gpio_chip *gc, unsigned int gpio,
+			  int val)
+{
+	return airoha_dir_set(gc, gpio, val, 1);
+}
+
+static int airoha_dir_in(struct gpio_chip *gc, unsigned int gpio)
+{
+	return airoha_dir_set(gc, gpio, 0, 0);
+}
+
+static int airoha_get_dir(struct gpio_chip *gc, unsigned int gpio)
+{
+	struct airoha_gpio_ctrl *ctrl = gc_to_ctrl(gc);
+	u32 dir = ioread32(ctrl->dir[gpio / 16]);
+	u32 mask = BIT((gpio % 16) * 2);
+
+	return dir & mask;
+}
+
+static const struct of_device_id airoha_gpio_of_match[] = {
+	{ .compatible = "airoha,en7523-gpio" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, airoha_gpio_of_match);
+
+static int airoha_gpio_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct airoha_gpio_ctrl *ctrl;
+	int err;
+
+	ctrl = devm_kzalloc(dev, sizeof(*ctrl), GFP_KERNEL);
+	if (!ctrl)
+		return -ENOMEM;
+
+	ctrl->data = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(ctrl->data))
+		return PTR_ERR(ctrl->data);
+
+	ctrl->dir[0] = devm_platform_ioremap_resource(pdev, 1);
+	if (IS_ERR(ctrl->dir[0]))
+		return PTR_ERR(ctrl->dir[0]);
+
+	ctrl->dir[1] = devm_platform_ioremap_resource(pdev, 2);
+	if (IS_ERR(ctrl->dir[1]))
+		return PTR_ERR(ctrl->dir[1]);
+
+	ctrl->output = devm_platform_ioremap_resource(pdev, 3);
+	if (IS_ERR(ctrl->output))
+		return PTR_ERR(ctrl->output);
+
+	err = bgpio_init(&ctrl->gc, dev, 4, ctrl->data, NULL,
+			 NULL, NULL, NULL, 0);
+	if (err) {
+		dev_err(dev, "unable to init generic GPIO");
+		return err;
+	}
+
+	ctrl->gc.ngpio = AIROHA_GPIO_MAX;
+	ctrl->gc.owner = THIS_MODULE;
+	ctrl->gc.direction_output = airoha_dir_out;
+	ctrl->gc.direction_input = airoha_dir_in;
+	ctrl->gc.get_direction = airoha_get_dir;
+
+	return devm_gpiochip_add_data(dev, &ctrl->gc, ctrl);
+}
+
+static struct platform_driver airoha_gpio_driver = {
+	.driver = {
+		.name = "airoha-gpio",
+		.of_match_table	= airoha_gpio_of_match,
+	},
+	.probe = airoha_gpio_probe,
+};
+module_platform_driver(airoha_gpio_driver);
+
+MODULE_DESCRIPTION("Airoha GPIO support");
+MODULE_AUTHOR("John Crispin <john@phrozen.org>");
+MODULE_LICENSE("GPL v2");
-- 
2.30.1

[PATCH v5 13/13] ARM: dts: add GPIO support for Airoha EN7523

[Felix Fietkau]

From: John Crispin <john@phrozen.org>

Airoha's GPIO controller on their ARM EN7523 SoCs consists of two banks of 32
GPIOs

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
 arch/arm/boot/dts/en7523-evb.dts |  8 ++++++++
 arch/arm/boot/dts/en7523.dtsi    | 20 ++++++++++++++++++++
 2 files changed, 28 insertions(+)

diff --git a/arch/arm/boot/dts/en7523-evb.dts b/arch/arm/boot/dts/en7523-evb.dts
index 0a79f5f6c311..cd9cded5b564 100644
--- a/arch/arm/boot/dts/en7523-evb.dts
+++ b/arch/arm/boot/dts/en7523-evb.dts
@@ -33,3 +33,11 @@ &pcie0 {
 &pcie1 {
 	status = "okay";
 };
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/en7523.dtsi b/arch/arm/boot/dts/en7523.dtsi
index 862da104d6f2..d9cc5a1b83b8 100644
--- a/arch/arm/boot/dts/en7523.dtsi
+++ b/arch/arm/boot/dts/en7523.dtsi
@@ -3,6 +3,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/en7523-clk.h>
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	interrupt-parent = <&gic>;
@@ -120,6 +121,25 @@ uart1: serial@1fbf0000 {
 		status = "okay";
 	};
 
+	gpio0: gpio@1fbf0200 {
+		compatible = "airoha,en7523-gpio";
+		reg = <0x1fbf0204 0x4>,
+		      <0x1fbf0200 0x4>,
+		      <0x1fbf0220 0x4>,
+		      <0x1fbf0214 0x4>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio1: gpio@1fbf0270 {
+		compatible = "airoha,en7523-gpio";
+		reg = <0x1fbf0270 0x4>,
+		      <0x1fbf0260 0x4>,
+		      <0x1fbf0264 0x4>,
+		      <0x1fbf0278 0x4>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
 
 	pcie0: pcie@1fa91000 {
 		compatible = "airoha,en7523-pcie", "mediatek,mt7622-pcie";
-- 
2.30.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 13/13] ARM: dts: add GPIO support for Airoha EN7523

[Felix Fietkau]

From: John Crispin <john@phrozen.org>

Airoha's GPIO controller on their ARM EN7523 SoCs consists of two banks of 32
GPIOs

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
 arch/arm/boot/dts/en7523-evb.dts |  8 ++++++++
 arch/arm/boot/dts/en7523.dtsi    | 20 ++++++++++++++++++++
 2 files changed, 28 insertions(+)

diff --git a/arch/arm/boot/dts/en7523-evb.dts b/arch/arm/boot/dts/en7523-evb.dts
index 0a79f5f6c311..cd9cded5b564 100644
--- a/arch/arm/boot/dts/en7523-evb.dts
+++ b/arch/arm/boot/dts/en7523-evb.dts
@@ -33,3 +33,11 @@ &pcie0 {
 &pcie1 {
 	status = "okay";
 };
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/en7523.dtsi b/arch/arm/boot/dts/en7523.dtsi
index 862da104d6f2..d9cc5a1b83b8 100644
--- a/arch/arm/boot/dts/en7523.dtsi
+++ b/arch/arm/boot/dts/en7523.dtsi
@@ -3,6 +3,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/en7523-clk.h>
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	interrupt-parent = <&gic>;
@@ -120,6 +121,25 @@ uart1: serial@1fbf0000 {
 		status = "okay";
 	};
 
+	gpio0: gpio@1fbf0200 {
+		compatible = "airoha,en7523-gpio";
+		reg = <0x1fbf0204 0x4>,
+		      <0x1fbf0200 0x4>,
+		      <0x1fbf0220 0x4>,
+		      <0x1fbf0214 0x4>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio1: gpio@1fbf0270 {
+		compatible = "airoha,en7523-gpio";
+		reg = <0x1fbf0270 0x4>,
+		      <0x1fbf0260 0x4>,
+		      <0x1fbf0264 0x4>,
+		      <0x1fbf0278 0x4>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
 
 	pcie0: pcie@1fa91000 {
 		compatible = "airoha,en7523-pcie", "mediatek,mt7622-pcie";
-- 
2.30.1

Re: [PATCH v5 09/13] PCI: mediatek: allow selecting controller driver for airoha arch

[Bjorn Helgaas]

On Mon, Nov 29, 2021 at 04:33:25PM +0100, Felix Fietkau wrote:
> The EN7523 SoC uses the same controller as MT7622

If you have occasion to post a v6, please:

  - Update the subject line so it starts with a capital letter,
    capitalizes "Airoha" appropriately, and includes "EN7523" as your
    DT patch does, and moves those close to the beginning, e.g.,

      PCI: mediatek: Allow selection for Airoha EN7532

  - Update the commit log so it says what this patch does.  It's OK to
    repeat the subject line.  Add a period at end.

I expected a patch to add "airoha,en7523-pcie" to
drivers/pci/controller/pcie-mediatek.c.  Did I miss it?

Oh, I see your arch/arm/boot/dts/en7523.dtsi has:

  +       pcie0: pcie@1fa91000 {
  +               compatible = "airoha,en7523-pcie", "mediatek,mt7622-pcie";

so I guess you just rely on the existing "mediatek,mt7622-pcie" string
in the driver?

> Signed-off-by: Felix Fietkau <nbd@nbd.name>
> ---
>  drivers/pci/controller/Kconfig | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig
> index 93b141110537..f1342059c2a3 100644
> --- a/drivers/pci/controller/Kconfig
> +++ b/drivers/pci/controller/Kconfig
> @@ -233,7 +233,7 @@ config PCIE_ROCKCHIP_EP
>  
>  config PCIE_MEDIATEK
>  	tristate "MediaTek PCIe controller"
> -	depends on ARCH_MEDIATEK || COMPILE_TEST
> +	depends on ARCH_AIROHA || ARCH_MEDIATEK || COMPILE_TEST
>  	depends on OF
>  	depends on PCI_MSI_IRQ_DOMAIN
>  	help
> -- 
> 2.30.1
> 

Re: [PATCH v5 09/13] PCI: mediatek: allow selecting controller driver for airoha arch

[Bjorn Helgaas]

On Mon, Nov 29, 2021 at 04:33:25PM +0100, Felix Fietkau wrote:
> The EN7523 SoC uses the same controller as MT7622

If you have occasion to post a v6, please:

  - Update the subject line so it starts with a capital letter,
    capitalizes "Airoha" appropriately, and includes "EN7523" as your
    DT patch does, and moves those close to the beginning, e.g.,

      PCI: mediatek: Allow selection for Airoha EN7532

  - Update the commit log so it says what this patch does.  It's OK to
    repeat the subject line.  Add a period at end.

I expected a patch to add "airoha,en7523-pcie" to
drivers/pci/controller/pcie-mediatek.c.  Did I miss it?

Oh, I see your arch/arm/boot/dts/en7523.dtsi has:

  +       pcie0: pcie@1fa91000 {
  +               compatible = "airoha,en7523-pcie", "mediatek,mt7622-pcie";

so I guess you just rely on the existing "mediatek,mt7622-pcie" string
in the driver?

> Signed-off-by: Felix Fietkau <nbd@nbd.name>
> ---
>  drivers/pci/controller/Kconfig | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig
> index 93b141110537..f1342059c2a3 100644
> --- a/drivers/pci/controller/Kconfig
> +++ b/drivers/pci/controller/Kconfig
> @@ -233,7 +233,7 @@ config PCIE_ROCKCHIP_EP
>  
>  config PCIE_MEDIATEK
>  	tristate "MediaTek PCIe controller"
> -	depends on ARCH_MEDIATEK || COMPILE_TEST
> +	depends on ARCH_AIROHA || ARCH_MEDIATEK || COMPILE_TEST
>  	depends on OF
>  	depends on PCI_MSI_IRQ_DOMAIN
>  	help
> -- 
> 2.30.1
> 

_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

Re: [PATCH v5 09/13] PCI: mediatek: allow selecting controller driver for airoha arch

[Bjorn Helgaas]

On Mon, Nov 29, 2021 at 04:33:25PM +0100, Felix Fietkau wrote:
> The EN7523 SoC uses the same controller as MT7622

If you have occasion to post a v6, please:

  - Update the subject line so it starts with a capital letter,
    capitalizes "Airoha" appropriately, and includes "EN7523" as your
    DT patch does, and moves those close to the beginning, e.g.,

      PCI: mediatek: Allow selection for Airoha EN7532

  - Update the commit log so it says what this patch does.  It's OK to
    repeat the subject line.  Add a period at end.

I expected a patch to add "airoha,en7523-pcie" to
drivers/pci/controller/pcie-mediatek.c.  Did I miss it?

Oh, I see your arch/arm/boot/dts/en7523.dtsi has:

  +       pcie0: pcie@1fa91000 {
  +               compatible = "airoha,en7523-pcie", "mediatek,mt7622-pcie";

so I guess you just rely on the existing "mediatek,mt7622-pcie" string
in the driver?

> Signed-off-by: Felix Fietkau <nbd@nbd.name>
> ---
>  drivers/pci/controller/Kconfig | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig
> index 93b141110537..f1342059c2a3 100644
> --- a/drivers/pci/controller/Kconfig
> +++ b/drivers/pci/controller/Kconfig
> @@ -233,7 +233,7 @@ config PCIE_ROCKCHIP_EP
>  
>  config PCIE_MEDIATEK
>  	tristate "MediaTek PCIe controller"
> -	depends on ARCH_MEDIATEK || COMPILE_TEST
> +	depends on ARCH_AIROHA || ARCH_MEDIATEK || COMPILE_TEST
>  	depends on OF
>  	depends on PCI_MSI_IRQ_DOMAIN
>  	help
> -- 
> 2.30.1
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 12/13] gpio: Add support for Airoha EN7523 GPIO controller

[Linus Walleij]

Hi Felix!

Thanks for your patch!

On Mon, Nov 29, 2021 at 4:54 PM Felix Fietkau <nbd@nbd.name> wrote:

> From: John Crispin <john@phrozen.org>
>
> Airoha's GPIO controller on their ARM EN7523 SoCs consists of two banks of 32
> GPIOs. Each instance in DT is for an single bank.
>
> Signed-off-by: John Crispin <john@phrozen.org>
> Signed-off-by: Felix Fietkau <nbd@nbd.name>

(...)
> +config GPIO_EN7523
> +       tristate "Airoha GPIO support"
> +       depends on ARCH_AIROHA
> +       default ARCH_AIROHA
> +       select GPIO_GENERIC

Yes that looks applicable, but why isn't it used?

The few 32-bit registers look like an ideal candidate for
using the generic GPIO. Check similar drivers such as
drivers/gpio/gpio-ftgpio010.c and how it uses
bgpio_init() and the nice doc for bgpio_init() in
drivers/gpio/gpio-mmio.c.

If it's not working already with generic GPIO I do not
think it would be far fetched to fix it.

Yours,
Linus Walleij

Re: [PATCH v5 12/13] gpio: Add support for Airoha EN7523 GPIO controller

[Linus Walleij]

Hi Felix!

Thanks for your patch!

On Mon, Nov 29, 2021 at 4:54 PM Felix Fietkau <nbd@nbd.name> wrote:

> From: John Crispin <john@phrozen.org>
>
> Airoha's GPIO controller on their ARM EN7523 SoCs consists of two banks of 32
> GPIOs. Each instance in DT is for an single bank.
>
> Signed-off-by: John Crispin <john@phrozen.org>
> Signed-off-by: Felix Fietkau <nbd@nbd.name>

(...)
> +config GPIO_EN7523
> +       tristate "Airoha GPIO support"
> +       depends on ARCH_AIROHA
> +       default ARCH_AIROHA
> +       select GPIO_GENERIC

Yes that looks applicable, but why isn't it used?

The few 32-bit registers look like an ideal candidate for
using the generic GPIO. Check similar drivers such as
drivers/gpio/gpio-ftgpio010.c and how it uses
bgpio_init() and the nice doc for bgpio_init() in
drivers/gpio/gpio-mmio.c.

If it's not working already with generic GPIO I do not
think it would be far fetched to fix it.

Yours,
Linus Walleij

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 07/13] clk: en7523: Add clock driver for Airoha EN7523 SoC

[kernel test robot]

Hi Felix,

I love your patch! Perhaps something to improve:

[auto build test WARNING on robh/for-next]
[also build test WARNING on clk/clk-next v5.16-rc3 next-20211202]
[cannot apply to linusw-gpio/for-next]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]

url:    https://github.com/0day-ci/linux/commits/Felix-Fietkau/dt-bindings-Add-vendor-prefix-for-Airoha/20211130-033938
base:   https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
config: mips-randconfig-s031-20211202 (https://download.01.org/0day-ci/archive/20211203/202112030121.BuKKR1T4-lkp@intel.com/config)
compiler: mips64-linux-gcc (GCC) 11.2.0
reproduce:
        wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
        chmod +x ~/bin/make.cross
        # apt-get install sparse
        # sparse version: v0.6.4-dirty
        # https://github.com/0day-ci/linux/commit/f1c5b70976ce5352c8ac2ae85739e1be63f59ec2
        git remote add linux-review https://github.com/0day-ci/linux
        git fetch --no-tags linux-review Felix-Fietkau/dt-bindings-Add-vendor-prefix-for-Airoha/20211130-033938
        git checkout f1c5b70976ce5352c8ac2ae85739e1be63f59ec2
        # save the config file to linux build tree
        mkdir build_dir
        COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-11.2.0 make.cross C=1 CF='-fdiagnostic-prefix -D__CHECK_ENDIAN__' O=build_dir ARCH=mips SHELL=/bin/bash drivers/clk/ drivers/gpio/

If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>


sparse warnings: (new ones prefixed by >>)
   command-line: note: in included file:
   builtin:1:9: sparse: sparse: preprocessor token __ATOMIC_ACQUIRE redefined
   builtin:0:0: sparse: this was the original definition
   builtin:1:9: sparse: sparse: preprocessor token __ATOMIC_SEQ_CST redefined
   builtin:0:0: sparse: this was the original definition
   builtin:1:9: sparse: sparse: preprocessor token __ATOMIC_ACQ_REL redefined
   builtin:0:0: sparse: this was the original definition
   builtin:1:9: sparse: sparse: preprocessor token __ATOMIC_RELEASE redefined
   builtin:0:0: sparse: this was the original definition
   drivers/clk/clk-en7523.c:202:27: sparse: sparse: incorrect type in initializer (different address spaces) @@     expected void *np_base @@     got void [noderef] __iomem *base @@
   drivers/clk/clk-en7523.c:202:27: sparse:     expected void *np_base
   drivers/clk/clk-en7523.c:202:27: sparse:     got void [noderef] __iomem *base
>> drivers/clk/clk-en7523.c:206:29: sparse: sparse: incorrect type in argument 1 (different address spaces) @@     expected void const volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:206:29: sparse:     expected void const volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:206:29: sparse:     got void *
>> drivers/clk/clk-en7523.c:208:29: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:208:29: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:208:29: sparse:     got void *
   drivers/clk/clk-en7523.c:213:29: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:213:29: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:213:29: sparse:     got void *
   drivers/clk/clk-en7523.c:217:29: sparse: sparse: incorrect type in argument 1 (different address spaces) @@     expected void const volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:217:29: sparse:     expected void const volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:217:29: sparse:     got void *
   drivers/clk/clk-en7523.c:220:37: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:220:37: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:220:37: sparse:     got void *
   drivers/clk/clk-en7523.c:222:36: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:222:36: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:222:36: sparse:     got void *
   drivers/clk/clk-en7523.c:224:37: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:224:37: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:224:37: sparse:     got void *
   drivers/clk/clk-en7523.c:229:29: sparse: sparse: incorrect type in argument 1 (different address spaces) @@     expected void const volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:229:29: sparse:     expected void const volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:229:29: sparse:     got void *
   drivers/clk/clk-en7523.c:230:37: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:230:37: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:230:37: sparse:     got void *
   drivers/clk/clk-en7523.c:232:36: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:232:36: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:232:36: sparse:     got void *
   drivers/clk/clk-en7523.c:241:27: sparse: sparse: incorrect type in initializer (different address spaces) @@     expected void *np_base @@     got void [noderef] __iomem *base @@
   drivers/clk/clk-en7523.c:241:27: sparse:     expected void *np_base
   drivers/clk/clk-en7523.c:241:27: sparse:     got void [noderef] __iomem *base
   drivers/clk/clk-en7523.c:244:29: sparse: sparse: incorrect type in argument 1 (different address spaces) @@     expected void const volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:244:29: sparse:     expected void const volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:244:29: sparse:     got void *
   drivers/clk/clk-en7523.c:246:29: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:246:29: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:246:29: sparse:     got void *

vim +206 drivers/clk/clk-en7523.c

   198	
   199	static int en7523_pci_enable(struct clk_hw *hw)
   200	{
   201		struct en_clk_gate *cg = container_of(hw, struct en_clk_gate, hw);
   202		void *np_base = cg->base;
   203		u32 val, mask;
   204	
   205		/* Need to pull device low before reset */
 > 206		val = readl(np_base + REG_PCI_CONTROL);
   207		val &= ~(REG_PCI_CONTROL_PERSTOUT1 | REG_PCI_CONTROL_PERSTOUT);
 > 208		writel(val, np_base + REG_PCI_CONTROL);
   209		usleep_range(1000, 2000);
   210	
   211		/* Enable PCIe port 1 */
   212		val |= REG_PCI_CONTROL_REFCLK_EN1;
   213		writel(val, np_base + REG_PCI_CONTROL);
   214		usleep_range(1000, 2000);
   215	
   216		/* Reset to default */
   217		val = readl(np_base + REG_RESET_CONTROL);
   218		mask = REG_RESET_CONTROL_PCIE1 | REG_RESET_CONTROL_PCIE2 |
   219		       REG_RESET_CONTROL_PCIEHB;
   220		writel(val & ~mask, np_base + REG_RESET_CONTROL);
   221		usleep_range(1000, 2000);
   222		writel(val | mask, np_base + REG_RESET_CONTROL);
   223		msleep(100);
   224		writel(val & ~mask, np_base + REG_RESET_CONTROL);
   225		usleep_range(5000, 10000);
   226	
   227		/* Release device */
   228		mask = REG_PCI_CONTROL_PERSTOUT1 | REG_PCI_CONTROL_PERSTOUT;
   229		val = readl(np_base + REG_PCI_CONTROL);
   230		writel(val & ~mask, np_base + REG_PCI_CONTROL);
   231		usleep_range(1000, 2000);
   232		writel(val | mask, np_base + REG_PCI_CONTROL);
   233		msleep(250);
   234	
   235		return 0;
   236	}
   237	

---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org

Re: [PATCH v5 07/13] clk: en7523: Add clock driver for Airoha EN7523 SoC

[kernel test robot]

Hi Felix,

I love your patch! Perhaps something to improve:

[auto build test WARNING on robh/for-next]
[also build test WARNING on clk/clk-next v5.16-rc3 next-20211202]
[cannot apply to linusw-gpio/for-next]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]

url:    https://github.com/0day-ci/linux/commits/Felix-Fietkau/dt-bindings-Add-vendor-prefix-for-Airoha/20211130-033938
base:   https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
config: mips-randconfig-s031-20211202 (https://download.01.org/0day-ci/archive/20211203/202112030121.BuKKR1T4-lkp@intel.com/config)
compiler: mips64-linux-gcc (GCC) 11.2.0
reproduce:
        wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
        chmod +x ~/bin/make.cross
        # apt-get install sparse
        # sparse version: v0.6.4-dirty
        # https://github.com/0day-ci/linux/commit/f1c5b70976ce5352c8ac2ae85739e1be63f59ec2
        git remote add linux-review https://github.com/0day-ci/linux
        git fetch --no-tags linux-review Felix-Fietkau/dt-bindings-Add-vendor-prefix-for-Airoha/20211130-033938
        git checkout f1c5b70976ce5352c8ac2ae85739e1be63f59ec2
        # save the config file to linux build tree
        mkdir build_dir
        COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-11.2.0 make.cross C=1 CF='-fdiagnostic-prefix -D__CHECK_ENDIAN__' O=build_dir ARCH=mips SHELL=/bin/bash drivers/clk/ drivers/gpio/

If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>


sparse warnings: (new ones prefixed by >>)
   command-line: note: in included file:
   builtin:1:9: sparse: sparse: preprocessor token __ATOMIC_ACQUIRE redefined
   builtin:0:0: sparse: this was the original definition
   builtin:1:9: sparse: sparse: preprocessor token __ATOMIC_SEQ_CST redefined
   builtin:0:0: sparse: this was the original definition
   builtin:1:9: sparse: sparse: preprocessor token __ATOMIC_ACQ_REL redefined
   builtin:0:0: sparse: this was the original definition
   builtin:1:9: sparse: sparse: preprocessor token __ATOMIC_RELEASE redefined
   builtin:0:0: sparse: this was the original definition
   drivers/clk/clk-en7523.c:202:27: sparse: sparse: incorrect type in initializer (different address spaces) @@     expected void *np_base @@     got void [noderef] __iomem *base @@
   drivers/clk/clk-en7523.c:202:27: sparse:     expected void *np_base
   drivers/clk/clk-en7523.c:202:27: sparse:     got void [noderef] __iomem *base
>> drivers/clk/clk-en7523.c:206:29: sparse: sparse: incorrect type in argument 1 (different address spaces) @@     expected void const volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:206:29: sparse:     expected void const volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:206:29: sparse:     got void *
>> drivers/clk/clk-en7523.c:208:29: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:208:29: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:208:29: sparse:     got void *
   drivers/clk/clk-en7523.c:213:29: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:213:29: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:213:29: sparse:     got void *
   drivers/clk/clk-en7523.c:217:29: sparse: sparse: incorrect type in argument 1 (different address spaces) @@     expected void const volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:217:29: sparse:     expected void const volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:217:29: sparse:     got void *
   drivers/clk/clk-en7523.c:220:37: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:220:37: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:220:37: sparse:     got void *
   drivers/clk/clk-en7523.c:222:36: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:222:36: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:222:36: sparse:     got void *
   drivers/clk/clk-en7523.c:224:37: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:224:37: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:224:37: sparse:     got void *
   drivers/clk/clk-en7523.c:229:29: sparse: sparse: incorrect type in argument 1 (different address spaces) @@     expected void const volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:229:29: sparse:     expected void const volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:229:29: sparse:     got void *
   drivers/clk/clk-en7523.c:230:37: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:230:37: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:230:37: sparse:     got void *
   drivers/clk/clk-en7523.c:232:36: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:232:36: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:232:36: sparse:     got void *
   drivers/clk/clk-en7523.c:241:27: sparse: sparse: incorrect type in initializer (different address spaces) @@     expected void *np_base @@     got void [noderef] __iomem *base @@
   drivers/clk/clk-en7523.c:241:27: sparse:     expected void *np_base
   drivers/clk/clk-en7523.c:241:27: sparse:     got void [noderef] __iomem *base
   drivers/clk/clk-en7523.c:244:29: sparse: sparse: incorrect type in argument 1 (different address spaces) @@     expected void const volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:244:29: sparse:     expected void const volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:244:29: sparse:     got void *
   drivers/clk/clk-en7523.c:246:29: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:246:29: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:246:29: sparse:     got void *

vim +206 drivers/clk/clk-en7523.c

   198	
   199	static int en7523_pci_enable(struct clk_hw *hw)
   200	{
   201		struct en_clk_gate *cg = container_of(hw, struct en_clk_gate, hw);
   202		void *np_base = cg->base;
   203		u32 val, mask;
   204	
   205		/* Need to pull device low before reset */
 > 206		val = readl(np_base + REG_PCI_CONTROL);
   207		val &= ~(REG_PCI_CONTROL_PERSTOUT1 | REG_PCI_CONTROL_PERSTOUT);
 > 208		writel(val, np_base + REG_PCI_CONTROL);
   209		usleep_range(1000, 2000);
   210	
   211		/* Enable PCIe port 1 */
   212		val |= REG_PCI_CONTROL_REFCLK_EN1;
   213		writel(val, np_base + REG_PCI_CONTROL);
   214		usleep_range(1000, 2000);
   215	
   216		/* Reset to default */
   217		val = readl(np_base + REG_RESET_CONTROL);
   218		mask = REG_RESET_CONTROL_PCIE1 | REG_RESET_CONTROL_PCIE2 |
   219		       REG_RESET_CONTROL_PCIEHB;
   220		writel(val & ~mask, np_base + REG_RESET_CONTROL);
   221		usleep_range(1000, 2000);
   222		writel(val | mask, np_base + REG_RESET_CONTROL);
   223		msleep(100);
   224		writel(val & ~mask, np_base + REG_RESET_CONTROL);
   225		usleep_range(5000, 10000);
   226	
   227		/* Release device */
   228		mask = REG_PCI_CONTROL_PERSTOUT1 | REG_PCI_CONTROL_PERSTOUT;
   229		val = readl(np_base + REG_PCI_CONTROL);
   230		writel(val & ~mask, np_base + REG_PCI_CONTROL);
   231		usleep_range(1000, 2000);
   232		writel(val | mask, np_base + REG_PCI_CONTROL);
   233		msleep(250);
   234	
   235		return 0;
   236	}
   237	

---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 07/13] clk: en7523: Add clock driver for Airoha EN7523 SoC

[kernel test robot]

[-- Attachment #1: Type: text/plain, Size: 8794 bytes --]

Hi Felix,

I love your patch! Perhaps something to improve:

[auto build test WARNING on robh/for-next]
[also build test WARNING on clk/clk-next v5.16-rc3 next-20211202]
[cannot apply to linusw-gpio/for-next]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]

url:    https://github.com/0day-ci/linux/commits/Felix-Fietkau/dt-bindings-Add-vendor-prefix-for-Airoha/20211130-033938
base:   https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
config: mips-randconfig-s031-20211202 (https://download.01.org/0day-ci/archive/20211203/202112030121.BuKKR1T4-lkp(a)intel.com/config)
compiler: mips64-linux-gcc (GCC) 11.2.0
reproduce:
        wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
        chmod +x ~/bin/make.cross
        # apt-get install sparse
        # sparse version: v0.6.4-dirty
        # https://github.com/0day-ci/linux/commit/f1c5b70976ce5352c8ac2ae85739e1be63f59ec2
        git remote add linux-review https://github.com/0day-ci/linux
        git fetch --no-tags linux-review Felix-Fietkau/dt-bindings-Add-vendor-prefix-for-Airoha/20211130-033938
        git checkout f1c5b70976ce5352c8ac2ae85739e1be63f59ec2
        # save the config file to linux build tree
        mkdir build_dir
        COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-11.2.0 make.cross C=1 CF='-fdiagnostic-prefix -D__CHECK_ENDIAN__' O=build_dir ARCH=mips SHELL=/bin/bash drivers/clk/ drivers/gpio/

If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>


sparse warnings: (new ones prefixed by >>)
   command-line: note: in included file:
   builtin:1:9: sparse: sparse: preprocessor token __ATOMIC_ACQUIRE redefined
   builtin:0:0: sparse: this was the original definition
   builtin:1:9: sparse: sparse: preprocessor token __ATOMIC_SEQ_CST redefined
   builtin:0:0: sparse: this was the original definition
   builtin:1:9: sparse: sparse: preprocessor token __ATOMIC_ACQ_REL redefined
   builtin:0:0: sparse: this was the original definition
   builtin:1:9: sparse: sparse: preprocessor token __ATOMIC_RELEASE redefined
   builtin:0:0: sparse: this was the original definition
   drivers/clk/clk-en7523.c:202:27: sparse: sparse: incorrect type in initializer (different address spaces) @@     expected void *np_base @@     got void [noderef] __iomem *base @@
   drivers/clk/clk-en7523.c:202:27: sparse:     expected void *np_base
   drivers/clk/clk-en7523.c:202:27: sparse:     got void [noderef] __iomem *base
>> drivers/clk/clk-en7523.c:206:29: sparse: sparse: incorrect type in argument 1 (different address spaces) @@     expected void const volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:206:29: sparse:     expected void const volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:206:29: sparse:     got void *
>> drivers/clk/clk-en7523.c:208:29: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:208:29: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:208:29: sparse:     got void *
   drivers/clk/clk-en7523.c:213:29: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:213:29: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:213:29: sparse:     got void *
   drivers/clk/clk-en7523.c:217:29: sparse: sparse: incorrect type in argument 1 (different address spaces) @@     expected void const volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:217:29: sparse:     expected void const volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:217:29: sparse:     got void *
   drivers/clk/clk-en7523.c:220:37: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:220:37: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:220:37: sparse:     got void *
   drivers/clk/clk-en7523.c:222:36: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:222:36: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:222:36: sparse:     got void *
   drivers/clk/clk-en7523.c:224:37: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:224:37: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:224:37: sparse:     got void *
   drivers/clk/clk-en7523.c:229:29: sparse: sparse: incorrect type in argument 1 (different address spaces) @@     expected void const volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:229:29: sparse:     expected void const volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:229:29: sparse:     got void *
   drivers/clk/clk-en7523.c:230:37: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:230:37: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:230:37: sparse:     got void *
   drivers/clk/clk-en7523.c:232:36: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:232:36: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:232:36: sparse:     got void *
   drivers/clk/clk-en7523.c:241:27: sparse: sparse: incorrect type in initializer (different address spaces) @@     expected void *np_base @@     got void [noderef] __iomem *base @@
   drivers/clk/clk-en7523.c:241:27: sparse:     expected void *np_base
   drivers/clk/clk-en7523.c:241:27: sparse:     got void [noderef] __iomem *base
   drivers/clk/clk-en7523.c:244:29: sparse: sparse: incorrect type in argument 1 (different address spaces) @@     expected void const volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:244:29: sparse:     expected void const volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:244:29: sparse:     got void *
   drivers/clk/clk-en7523.c:246:29: sparse: sparse: incorrect type in argument 2 (different address spaces) @@     expected void volatile [noderef] __iomem *mem @@     got void * @@
   drivers/clk/clk-en7523.c:246:29: sparse:     expected void volatile [noderef] __iomem *mem
   drivers/clk/clk-en7523.c:246:29: sparse:     got void *

vim +206 drivers/clk/clk-en7523.c

   198	
   199	static int en7523_pci_enable(struct clk_hw *hw)
   200	{
   201		struct en_clk_gate *cg = container_of(hw, struct en_clk_gate, hw);
   202		void *np_base = cg->base;
   203		u32 val, mask;
   204	
   205		/* Need to pull device low before reset */
 > 206		val = readl(np_base + REG_PCI_CONTROL);
   207		val &= ~(REG_PCI_CONTROL_PERSTOUT1 | REG_PCI_CONTROL_PERSTOUT);
 > 208		writel(val, np_base + REG_PCI_CONTROL);
   209		usleep_range(1000, 2000);
   210	
   211		/* Enable PCIe port 1 */
   212		val |= REG_PCI_CONTROL_REFCLK_EN1;
   213		writel(val, np_base + REG_PCI_CONTROL);
   214		usleep_range(1000, 2000);
   215	
   216		/* Reset to default */
   217		val = readl(np_base + REG_RESET_CONTROL);
   218		mask = REG_RESET_CONTROL_PCIE1 | REG_RESET_CONTROL_PCIE2 |
   219		       REG_RESET_CONTROL_PCIEHB;
   220		writel(val & ~mask, np_base + REG_RESET_CONTROL);
   221		usleep_range(1000, 2000);
   222		writel(val | mask, np_base + REG_RESET_CONTROL);
   223		msleep(100);
   224		writel(val & ~mask, np_base + REG_RESET_CONTROL);
   225		usleep_range(5000, 10000);
   226	
   227		/* Release device */
   228		mask = REG_PCI_CONTROL_PERSTOUT1 | REG_PCI_CONTROL_PERSTOUT;
   229		val = readl(np_base + REG_PCI_CONTROL);
   230		writel(val & ~mask, np_base + REG_PCI_CONTROL);
   231		usleep_range(1000, 2000);
   232		writel(val | mask, np_base + REG_PCI_CONTROL);
   233		msleep(250);
   234	
   235		return 0;
   236	}
   237	

---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all(a)lists.01.org

Re: [PATCH v5 12/13] gpio: Add support for Airoha EN7523 GPIO controller

[Felix Fietkau]

On 2021-12-02 02:47, Linus Walleij wrote:
> Hi Felix!
> 
> Thanks for your patch!
> 
> On Mon, Nov 29, 2021 at 4:54 PM Felix Fietkau <nbd@nbd.name> wrote:
> 
>> From: John Crispin <john@phrozen.org>
>>
>> Airoha's GPIO controller on their ARM EN7523 SoCs consists of two banks of 32
>> GPIOs. Each instance in DT is for an single bank.
>>
>> Signed-off-by: John Crispin <john@phrozen.org>
>> Signed-off-by: Felix Fietkau <nbd@nbd.name>
> 
> (...)
>> +config GPIO_EN7523
>> +       tristate "Airoha GPIO support"
>> +       depends on ARCH_AIROHA
>> +       default ARCH_AIROHA
>> +       select GPIO_GENERIC
> 
> Yes that looks applicable, but why isn't it used?
> 
> The few 32-bit registers look like an ideal candidate for
> using the generic GPIO. Check similar drivers such as
> drivers/gpio/gpio-ftgpio010.c and how it uses
> bgpio_init() and the nice doc for bgpio_init() in
> drivers/gpio/gpio-mmio.c.
I just looked at the datasheet and the driver code again, and I think 
EN7523 is too strange for proper generic GPIO support.

For each bank there are two control registers (not consecutive), which 
have 2-bit fields for every GPIO line to control direction. No idea why 
2 bits per line, because only values 0 and 1 are valid, the rest are 
reserved.
For lines configured as output, an extra output-enable bit also needs to 
be set in a separate register before output values can be written.

The code does use bgpio to read/write values, but that's about it.
I don't think it would do the generic GPIO code any good to support this 
weirdness.

- Felix

Re: [PATCH v5 12/13] gpio: Add support for Airoha EN7523 GPIO controller

[Felix Fietkau]

On 2021-12-02 02:47, Linus Walleij wrote:
> Hi Felix!
> 
> Thanks for your patch!
> 
> On Mon, Nov 29, 2021 at 4:54 PM Felix Fietkau <nbd@nbd.name> wrote:
> 
>> From: John Crispin <john@phrozen.org>
>>
>> Airoha's GPIO controller on their ARM EN7523 SoCs consists of two banks of 32
>> GPIOs. Each instance in DT is for an single bank.
>>
>> Signed-off-by: John Crispin <john@phrozen.org>
>> Signed-off-by: Felix Fietkau <nbd@nbd.name>
> 
> (...)
>> +config GPIO_EN7523
>> +       tristate "Airoha GPIO support"
>> +       depends on ARCH_AIROHA
>> +       default ARCH_AIROHA
>> +       select GPIO_GENERIC
> 
> Yes that looks applicable, but why isn't it used?
> 
> The few 32-bit registers look like an ideal candidate for
> using the generic GPIO. Check similar drivers such as
> drivers/gpio/gpio-ftgpio010.c and how it uses
> bgpio_init() and the nice doc for bgpio_init() in
> drivers/gpio/gpio-mmio.c.
I just looked at the datasheet and the driver code again, and I think 
EN7523 is too strange for proper generic GPIO support.

For each bank there are two control registers (not consecutive), which 
have 2-bit fields for every GPIO line to control direction. No idea why 
2 bits per line, because only values 0 and 1 are valid, the rest are 
reserved.
For lines configured as output, an extra output-enable bit also needs to 
be set in a separate register before output values can be written.

The code does use bgpio to read/write values, but that's about it.
I don't think it would do the generic GPIO code any good to support this 
weirdness.

- Felix

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 12/13] gpio: Add support for Airoha EN7523 GPIO controller

[John Crispin]

On 02.12.21 18:59, Felix Fietkau wrote:
> 
> On 2021-12-02 02:47, Linus Walleij wrote:
>> Hi Felix!
>>
>> Thanks for your patch!
>>
>> On Mon, Nov 29, 2021 at 4:54 PM Felix Fietkau <nbd@nbd.name> wrote:
>>
>>> From: John Crispin <john@phrozen.org>
>>>
>>> Airoha's GPIO controller on their ARM EN7523 SoCs consists of two 
>>> banks of 32
>>> GPIOs. Each instance in DT is for an single bank.
>>>
>>> Signed-off-by: John Crispin <john@phrozen.org>
>>> Signed-off-by: Felix Fietkau <nbd@nbd.name>
>>
>> (...)
>>> +config GPIO_EN7523
>>> +       tristate "Airoha GPIO support"
>>> +       depends on ARCH_AIROHA
>>> +       default ARCH_AIROHA
>>> +       select GPIO_GENERIC
>>
>> Yes that looks applicable, but why isn't it used?
>>
>> The few 32-bit registers look like an ideal candidate for
>> using the generic GPIO. Check similar drivers such as
>> drivers/gpio/gpio-ftgpio010.c and how it uses
>> bgpio_init() and the nice doc for bgpio_init() in
>> drivers/gpio/gpio-mmio.c.
> I just looked at the datasheet and the driver code again, and I think 
> EN7523 is too strange for proper generic GPIO support.
> 
> For each bank there are two control registers (not consecutive), which 
> have 2-bit fields for every GPIO line to control direction. No idea why 
> 2 bits per line, because only values 0 and 1 are valid, the rest are 
> reserved.
> For lines configured as output, an extra output-enable bit also needs to 
> be set in a separate register before output values can be written.
> 
> The code does use bgpio to read/write values, but that's about it.
> I don't think it would do the generic GPIO code any good to support this 
> weirdness.
> 
> - Felix
Hi Linus,
I sent an email to you 16.06.21 explaining all of this and you replied, 
telling me that this approach is the most reasonable one to take.
	John

Re: [PATCH v5 12/13] gpio: Add support for Airoha EN7523 GPIO controller

[John Crispin]

On 02.12.21 18:59, Felix Fietkau wrote:
> 
> On 2021-12-02 02:47, Linus Walleij wrote:
>> Hi Felix!
>>
>> Thanks for your patch!
>>
>> On Mon, Nov 29, 2021 at 4:54 PM Felix Fietkau <nbd@nbd.name> wrote:
>>
>>> From: John Crispin <john@phrozen.org>
>>>
>>> Airoha's GPIO controller on their ARM EN7523 SoCs consists of two 
>>> banks of 32
>>> GPIOs. Each instance in DT is for an single bank.
>>>
>>> Signed-off-by: John Crispin <john@phrozen.org>
>>> Signed-off-by: Felix Fietkau <nbd@nbd.name>
>>
>> (...)
>>> +config GPIO_EN7523
>>> +       tristate "Airoha GPIO support"
>>> +       depends on ARCH_AIROHA
>>> +       default ARCH_AIROHA
>>> +       select GPIO_GENERIC
>>
>> Yes that looks applicable, but why isn't it used?
>>
>> The few 32-bit registers look like an ideal candidate for
>> using the generic GPIO. Check similar drivers such as
>> drivers/gpio/gpio-ftgpio010.c and how it uses
>> bgpio_init() and the nice doc for bgpio_init() in
>> drivers/gpio/gpio-mmio.c.
> I just looked at the datasheet and the driver code again, and I think 
> EN7523 is too strange for proper generic GPIO support.
> 
> For each bank there are two control registers (not consecutive), which 
> have 2-bit fields for every GPIO line to control direction. No idea why 
> 2 bits per line, because only values 0 and 1 are valid, the rest are 
> reserved.
> For lines configured as output, an extra output-enable bit also needs to 
> be set in a separate register before output values can be written.
> 
> The code does use bgpio to read/write values, but that's about it.
> I don't think it would do the generic GPIO code any good to support this 
> weirdness.
> 
> - Felix
Hi Linus,
I sent an email to you 16.06.21 explaining all of this and you replied, 
telling me that this approach is the most reasonable one to take.
	John

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 07/13] clk: en7523: Add clock driver for Airoha EN7523 SoC

[Stephen Boyd]

Quoting Felix Fietkau (2021-11-29 07:33:23)
> This driver only registers fixed rate clocks, since the clocks are fully
> initialized by the boot loader and should not be changed later, according
> to Airoha.
> 
> Signed-off-by: Felix Fietkau <nbd@nbd.name>
> ---
>  arch/arm/boot/dts/en7523.dtsi |   8 +
>  drivers/clk/Kconfig           |   9 +
>  drivers/clk/Makefile          |   1 +
>  drivers/clk/clk-en7523.c      | 356 ++++++++++++++++++++++++++++++++++
>  4 files changed, 374 insertions(+)
>  create mode 100644 drivers/clk/clk-en7523.c

Pleas don't mix clk driver changes and dts file updates together.
Instead, introduce the clk driver in one patch and add the dts node in
another patch so that the different maintainers can pick up the patch
for the area they maintain.

> diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
> index c5b3dc97396a..b542f58c58d2 100644
> --- a/drivers/clk/Kconfig
> +++ b/drivers/clk/Kconfig
> @@ -192,6 +192,15 @@ config COMMON_CLK_CS2000_CP
>         help
>           If you say yes here you get support for the CS2000 clock multiplier.
>  
> +config COMMON_CLK_EN7523
> +       bool "Clock driver for Airoha EN7523 SoC system clocks"
> +       depends on OF
> +       depends on ARCH_AIROHA || ARM || COMPILE_TEST

Is this supposed to have parenthesis somewhere? Why is depending on ARM
useful?

> +       default ARCH_AIROHA
> +       help
> +         This driver provides the fixed clocks and gates present on Airoha
> +         ARM silicon.
> +
>  config COMMON_CLK_FSL_FLEXSPI
>         tristate "Clock driver for FlexSPI on Layerscape SoCs"
>         depends on ARCH_LAYERSCAPE || COMPILE_TEST
> diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
> index e42312121e51..be11d88c1603 100644
> --- a/drivers/clk/Makefile
> +++ b/drivers/clk/Makefile
> @@ -27,6 +27,7 @@ obj-$(CONFIG_COMMON_CLK_CDCE925)      += clk-cdce925.o
>  obj-$(CONFIG_ARCH_CLPS711X)            += clk-clps711x.o
>  obj-$(CONFIG_COMMON_CLK_CS2000_CP)     += clk-cs2000-cp.o
>  obj-$(CONFIG_ARCH_SPARX5)              += clk-sparx5.o
> +obj-$(CONFIG_COMMON_CLK_EN7523)                += clk-en7523.o
>  obj-$(CONFIG_COMMON_CLK_FIXED_MMIO)    += clk-fixed-mmio.o
>  obj-$(CONFIG_COMMON_CLK_FSL_FLEXSPI)   += clk-fsl-flexspi.o
>  obj-$(CONFIG_COMMON_CLK_FSL_SAI)       += clk-fsl-sai.o
> diff --git a/drivers/clk/clk-en7523.c b/drivers/clk/clk-en7523.c
> new file mode 100644
> index 000000000000..f1774a5bf537
> --- /dev/null
> +++ b/drivers/clk/clk-en7523.c
> @@ -0,0 +1,356 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +
> +#include <linux/regmap.h>
> +#include <linux/clk-provider.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/of_device.h>
> +#include <linux/platform_device.h>
> +#include <dt-bindings/clock/en7523-clk.h>
> +#include <linux/clk.h>

Is this include used?

> +
> +#define REG_PCI_CONTROL                        0x88
> +#define   REG_PCI_CONTROL_PERSTOUT     BIT(29)
> +#define   REG_PCI_CONTROL_PERSTOUT1    BIT(26)
> +#define   REG_PCI_CONTROL_REFCLK_EN1   BIT(22)
> +#define REG_GSW_CLK_DIV_SEL            0x1b4
[...]
> +
> +static struct clk *en7523_register_pcie_clk(struct device *dev,
> +                                           void __iomem *np_base)
> +{
> +       static const struct clk_ops pcie_gate_ops = {
> +               .is_enabled = en7523_pci_is_enabled,
> +               .enable = en7523_pci_enable,
> +               .disable = en7523_pci_disable,
> +       };
> +       struct clk_init_data init = {
> +               .name = "pcie",
> +               .ops = &pcie_gate_ops,
> +       };
> +       struct en_clk_gate *cg;
> +       struct clk *clk;
> +
> +       cg = devm_kzalloc(dev, sizeof(*cg), GFP_KERNEL);
> +       if (!cg)
> +               return NULL;
> +
> +       cg->base = np_base;
> +       cg->hw.init = &init;
> +       en7523_pci_disable(&cg->hw);
> +
> +       clk = clk_register(NULL, &cg->hw);

Please use clk_hw_register

> +       if (IS_ERR(clk))
> +               clk = NULL;
> +
> +       return clk;
> +}
> +
> +static void en7523_register_clocks(struct device *dev, struct clk_onecell_data *clk_data,
> +                                  void __iomem *base, void __iomem *np_base)
> +{
> +       struct clk *clk;
> +       u32 rate;
> +       int i;
> +
> +       for (i = 0; i < ARRAY_SIZE(en7523_base_clks); i++) {
> +               const struct en_clk_desc *desc = &en7523_base_clks[i];
> +
> +               rate = en7523_get_base_rate(base, i);
> +               rate /= en7523_get_div(base, i);
> +
> +               clk = clk_register_fixed_rate(NULL, desc->name, NULL, 0, rate);
> +               if (IS_ERR(clk)) {
> +                       pr_err("Failed to register clk %s: %ld\n",
> +                              desc->name, PTR_ERR(clk));
> +                       continue;
> +               }
> +
> +               clk_data->clks[desc->id] = clk;
> +       }
> +
> +       clk = en7523_register_pcie_clk(dev, np_base);
> +       clk_data->clks[EN7523_CLK_PCIE] = clk;
> +
> +       clk_data->clk_num = EN7523_NUM_CLOCKS;
> +}
> +
> +static int en7523_clk_probe(struct platform_device *pdev)
> +{
> +       struct device_node *node = pdev->dev.of_node;
> +       struct clk_onecell_data *clk_data;
> +       void __iomem *base, *np_base;
> +       int r;
> +
> +       base = devm_platform_ioremap_resource(pdev, 0);
> +       if (IS_ERR(base))
> +               return PTR_ERR(base);
> +
> +       np_base = devm_platform_ioremap_resource(pdev, 1);
> +       if (IS_ERR(base))
> +               return PTR_ERR(np_base);
> +
> +       clk_data = devm_kzalloc(&pdev->dev, sizeof(*clk_data), GFP_KERNEL);
> +       if (!clk_data)
> +               return -ENOMEM;
> +
> +       clk_data->clks = devm_kcalloc(&pdev->dev, EN7523_NUM_CLOCKS,
> +                                     sizeof(*clk_data->clks), GFP_KERNEL);
> +       if (!clk_data->clks)
> +               return -ENOMEM;
> +
> +       en7523_register_clocks(&pdev->dev, clk_data, base, np_base);
> +
> +       r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data);

Please add a clk_hw provider instead of a clk provider.

> +       if (r)

Re: [PATCH v5 07/13] clk: en7523: Add clock driver for Airoha EN7523 SoC

[Stephen Boyd]

Quoting Felix Fietkau (2021-11-29 07:33:23)
> This driver only registers fixed rate clocks, since the clocks are fully
> initialized by the boot loader and should not be changed later, according
> to Airoha.
> 
> Signed-off-by: Felix Fietkau <nbd@nbd.name>
> ---
>  arch/arm/boot/dts/en7523.dtsi |   8 +
>  drivers/clk/Kconfig           |   9 +
>  drivers/clk/Makefile          |   1 +
>  drivers/clk/clk-en7523.c      | 356 ++++++++++++++++++++++++++++++++++
>  4 files changed, 374 insertions(+)
>  create mode 100644 drivers/clk/clk-en7523.c

Pleas don't mix clk driver changes and dts file updates together.
Instead, introduce the clk driver in one patch and add the dts node in
another patch so that the different maintainers can pick up the patch
for the area they maintain.

> diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
> index c5b3dc97396a..b542f58c58d2 100644
> --- a/drivers/clk/Kconfig
> +++ b/drivers/clk/Kconfig
> @@ -192,6 +192,15 @@ config COMMON_CLK_CS2000_CP
>         help
>           If you say yes here you get support for the CS2000 clock multiplier.
>  
> +config COMMON_CLK_EN7523
> +       bool "Clock driver for Airoha EN7523 SoC system clocks"
> +       depends on OF
> +       depends on ARCH_AIROHA || ARM || COMPILE_TEST

Is this supposed to have parenthesis somewhere? Why is depending on ARM
useful?

> +       default ARCH_AIROHA
> +       help
> +         This driver provides the fixed clocks and gates present on Airoha
> +         ARM silicon.
> +
>  config COMMON_CLK_FSL_FLEXSPI
>         tristate "Clock driver for FlexSPI on Layerscape SoCs"
>         depends on ARCH_LAYERSCAPE || COMPILE_TEST
> diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
> index e42312121e51..be11d88c1603 100644
> --- a/drivers/clk/Makefile
> +++ b/drivers/clk/Makefile
> @@ -27,6 +27,7 @@ obj-$(CONFIG_COMMON_CLK_CDCE925)      += clk-cdce925.o
>  obj-$(CONFIG_ARCH_CLPS711X)            += clk-clps711x.o
>  obj-$(CONFIG_COMMON_CLK_CS2000_CP)     += clk-cs2000-cp.o
>  obj-$(CONFIG_ARCH_SPARX5)              += clk-sparx5.o
> +obj-$(CONFIG_COMMON_CLK_EN7523)                += clk-en7523.o
>  obj-$(CONFIG_COMMON_CLK_FIXED_MMIO)    += clk-fixed-mmio.o
>  obj-$(CONFIG_COMMON_CLK_FSL_FLEXSPI)   += clk-fsl-flexspi.o
>  obj-$(CONFIG_COMMON_CLK_FSL_SAI)       += clk-fsl-sai.o
> diff --git a/drivers/clk/clk-en7523.c b/drivers/clk/clk-en7523.c
> new file mode 100644
> index 000000000000..f1774a5bf537
> --- /dev/null
> +++ b/drivers/clk/clk-en7523.c
> @@ -0,0 +1,356 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +
> +#include <linux/regmap.h>
> +#include <linux/clk-provider.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/of_device.h>
> +#include <linux/platform_device.h>
> +#include <dt-bindings/clock/en7523-clk.h>
> +#include <linux/clk.h>

Is this include used?

> +
> +#define REG_PCI_CONTROL                        0x88
> +#define   REG_PCI_CONTROL_PERSTOUT     BIT(29)
> +#define   REG_PCI_CONTROL_PERSTOUT1    BIT(26)
> +#define   REG_PCI_CONTROL_REFCLK_EN1   BIT(22)
> +#define REG_GSW_CLK_DIV_SEL            0x1b4
[...]
> +
> +static struct clk *en7523_register_pcie_clk(struct device *dev,
> +                                           void __iomem *np_base)
> +{
> +       static const struct clk_ops pcie_gate_ops = {
> +               .is_enabled = en7523_pci_is_enabled,
> +               .enable = en7523_pci_enable,
> +               .disable = en7523_pci_disable,
> +       };
> +       struct clk_init_data init = {
> +               .name = "pcie",
> +               .ops = &pcie_gate_ops,
> +       };
> +       struct en_clk_gate *cg;
> +       struct clk *clk;
> +
> +       cg = devm_kzalloc(dev, sizeof(*cg), GFP_KERNEL);
> +       if (!cg)
> +               return NULL;
> +
> +       cg->base = np_base;
> +       cg->hw.init = &init;
> +       en7523_pci_disable(&cg->hw);
> +
> +       clk = clk_register(NULL, &cg->hw);

Please use clk_hw_register

> +       if (IS_ERR(clk))
> +               clk = NULL;
> +
> +       return clk;
> +}
> +
> +static void en7523_register_clocks(struct device *dev, struct clk_onecell_data *clk_data,
> +                                  void __iomem *base, void __iomem *np_base)
> +{
> +       struct clk *clk;
> +       u32 rate;
> +       int i;
> +
> +       for (i = 0; i < ARRAY_SIZE(en7523_base_clks); i++) {
> +               const struct en_clk_desc *desc = &en7523_base_clks[i];
> +
> +               rate = en7523_get_base_rate(base, i);
> +               rate /= en7523_get_div(base, i);
> +
> +               clk = clk_register_fixed_rate(NULL, desc->name, NULL, 0, rate);
> +               if (IS_ERR(clk)) {
> +                       pr_err("Failed to register clk %s: %ld\n",
> +                              desc->name, PTR_ERR(clk));
> +                       continue;
> +               }
> +
> +               clk_data->clks[desc->id] = clk;
> +       }
> +
> +       clk = en7523_register_pcie_clk(dev, np_base);
> +       clk_data->clks[EN7523_CLK_PCIE] = clk;
> +
> +       clk_data->clk_num = EN7523_NUM_CLOCKS;
> +}
> +
> +static int en7523_clk_probe(struct platform_device *pdev)
> +{
> +       struct device_node *node = pdev->dev.of_node;
> +       struct clk_onecell_data *clk_data;
> +       void __iomem *base, *np_base;
> +       int r;
> +
> +       base = devm_platform_ioremap_resource(pdev, 0);
> +       if (IS_ERR(base))
> +               return PTR_ERR(base);
> +
> +       np_base = devm_platform_ioremap_resource(pdev, 1);
> +       if (IS_ERR(base))
> +               return PTR_ERR(np_base);
> +
> +       clk_data = devm_kzalloc(&pdev->dev, sizeof(*clk_data), GFP_KERNEL);
> +       if (!clk_data)
> +               return -ENOMEM;
> +
> +       clk_data->clks = devm_kcalloc(&pdev->dev, EN7523_NUM_CLOCKS,
> +                                     sizeof(*clk_data->clks), GFP_KERNEL);
> +       if (!clk_data->clks)
> +               return -ENOMEM;
> +
> +       en7523_register_clocks(&pdev->dev, clk_data, base, np_base);
> +
> +       r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data);

Please add a clk_hw provider instead of a clk provider.

> +       if (r)

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 12/13] gpio: Add support for Airoha EN7523 GPIO controller

[Linus Walleij]

On Thu, Dec 2, 2021 at 8:02 PM John Crispin <john@phrozen.org> wrote:

> Hi Linus,
> I sent an email to you 16.06.21 explaining all of this and you replied,
> telling me that this approach is the most reasonable one to take.
>         John

Sadly I don't remember that, too long ago!

Anyways let's just go ahead with this.

Yours,
Linus Walleij

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 12/13] gpio: Add support for Airoha EN7523 GPIO controller

[Linus Walleij]

On Thu, Dec 2, 2021 at 8:02 PM John Crispin <john@phrozen.org> wrote:

> Hi Linus,
> I sent an email to you 16.06.21 explaining all of this and you replied,
> telling me that this approach is the most reasonable one to take.
>         John

Sadly I don't remember that, too long ago!

Anyways let's just go ahead with this.

Yours,
Linus Walleij

Re: [PATCH v5 12/13] gpio: Add support for Airoha EN7523 GPIO controller

[Linus Walleij]

On Thu, Dec 2, 2021 at 6:59 PM Felix Fietkau <nbd@nbd.name> wrote:

> I just looked at the datasheet and the driver code again, and I think
> EN7523 is too strange for proper generic GPIO support.

Yup I see that John explained it to me in the past, no problem.
Let's do it like this then, but just drop select GPIO_GENERIC
from KConfig since it's not used.

With that oneliner change:
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Yours,
Linus Walleij

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 12/13] gpio: Add support for Airoha EN7523 GPIO controller

[Linus Walleij]

On Thu, Dec 2, 2021 at 6:59 PM Felix Fietkau <nbd@nbd.name> wrote:

> I just looked at the datasheet and the driver code again, and I think
> EN7523 is too strange for proper generic GPIO support.

Yup I see that John explained it to me in the past, no problem.
Let's do it like this then, but just drop select GPIO_GENERIC
from KConfig since it's not used.

With that oneliner change:
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Yours,
Linus Walleij

Re: [PATCH v5 09/13] PCI: mediatek: allow selecting controller driver for airoha arch

[Bjorn Helgaas]

On Mon, Nov 29, 2021 at 05:55:50PM -0600, Bjorn Helgaas wrote:
> On Mon, Nov 29, 2021 at 04:33:25PM +0100, Felix Fietkau wrote:
> > The EN7523 SoC uses the same controller as MT7622
> 
> If you have occasion to post a v6, please:
> 
>   - Update the subject line so it starts with a capital letter,
>     capitalizes "Airoha" appropriately, and includes "EN7523" as your
>     DT patch does, and moves those close to the beginning, e.g.,
> 
>       PCI: mediatek: Allow selection for Airoha EN7532
> 
>   - Update the commit log so it says what this patch does.  It's OK to
>     repeat the subject line.  Add a period at end.

Sending again since you posted a v6 without doing any of the above.

> > Signed-off-by: Felix Fietkau <nbd@nbd.name>
> > ---
> >  drivers/pci/controller/Kconfig | 2 +-
> >  1 file changed, 1 insertion(+), 1 deletion(-)
> > 
> > diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig
> > index 93b141110537..f1342059c2a3 100644
> > --- a/drivers/pci/controller/Kconfig
> > +++ b/drivers/pci/controller/Kconfig
> > @@ -233,7 +233,7 @@ config PCIE_ROCKCHIP_EP
> >  
> >  config PCIE_MEDIATEK
> >  	tristate "MediaTek PCIe controller"
> > -	depends on ARCH_MEDIATEK || COMPILE_TEST
> > +	depends on ARCH_AIROHA || ARCH_MEDIATEK || COMPILE_TEST
> >  	depends on OF
> >  	depends on PCI_MSI_IRQ_DOMAIN
> >  	help
> > -- 
> > 2.30.1
> > 

Re: [PATCH v5 09/13] PCI: mediatek: allow selecting controller driver for airoha arch

[Bjorn Helgaas]

On Mon, Nov 29, 2021 at 05:55:50PM -0600, Bjorn Helgaas wrote:
> On Mon, Nov 29, 2021 at 04:33:25PM +0100, Felix Fietkau wrote:
> > The EN7523 SoC uses the same controller as MT7622
> 
> If you have occasion to post a v6, please:
> 
>   - Update the subject line so it starts with a capital letter,
>     capitalizes "Airoha" appropriately, and includes "EN7523" as your
>     DT patch does, and moves those close to the beginning, e.g.,
> 
>       PCI: mediatek: Allow selection for Airoha EN7532
> 
>   - Update the commit log so it says what this patch does.  It's OK to
>     repeat the subject line.  Add a period at end.

Sending again since you posted a v6 without doing any of the above.

> > Signed-off-by: Felix Fietkau <nbd@nbd.name>
> > ---
> >  drivers/pci/controller/Kconfig | 2 +-
> >  1 file changed, 1 insertion(+), 1 deletion(-)
> > 
> > diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig
> > index 93b141110537..f1342059c2a3 100644
> > --- a/drivers/pci/controller/Kconfig
> > +++ b/drivers/pci/controller/Kconfig
> > @@ -233,7 +233,7 @@ config PCIE_ROCKCHIP_EP
> >  
> >  config PCIE_MEDIATEK
> >  	tristate "MediaTek PCIe controller"
> > -	depends on ARCH_MEDIATEK || COMPILE_TEST
> > +	depends on ARCH_AIROHA || ARCH_MEDIATEK || COMPILE_TEST
> >  	depends on OF
> >  	depends on PCI_MSI_IRQ_DOMAIN
> >  	help
> > -- 
> > 2.30.1
> > 

_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

Re: [PATCH v5 09/13] PCI: mediatek: allow selecting controller driver for airoha arch

[Bjorn Helgaas]

On Mon, Nov 29, 2021 at 05:55:50PM -0600, Bjorn Helgaas wrote:
> On Mon, Nov 29, 2021 at 04:33:25PM +0100, Felix Fietkau wrote:
> > The EN7523 SoC uses the same controller as MT7622
> 
> If you have occasion to post a v6, please:
> 
>   - Update the subject line so it starts with a capital letter,
>     capitalizes "Airoha" appropriately, and includes "EN7523" as your
>     DT patch does, and moves those close to the beginning, e.g.,
> 
>       PCI: mediatek: Allow selection for Airoha EN7532
> 
>   - Update the commit log so it says what this patch does.  It's OK to
>     repeat the subject line.  Add a period at end.

Sending again since you posted a v6 without doing any of the above.

> > Signed-off-by: Felix Fietkau <nbd@nbd.name>
> > ---
> >  drivers/pci/controller/Kconfig | 2 +-
> >  1 file changed, 1 insertion(+), 1 deletion(-)
> > 
> > diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig
> > index 93b141110537..f1342059c2a3 100644
> > --- a/drivers/pci/controller/Kconfig
> > +++ b/drivers/pci/controller/Kconfig
> > @@ -233,7 +233,7 @@ config PCIE_ROCKCHIP_EP
> >  
> >  config PCIE_MEDIATEK
> >  	tristate "MediaTek PCIe controller"
> > -	depends on ARCH_MEDIATEK || COMPILE_TEST
> > +	depends on ARCH_AIROHA || ARCH_MEDIATEK || COMPILE_TEST
> >  	depends on OF
> >  	depends on PCI_MSI_IRQ_DOMAIN
> >  	help
> > -- 
> > 2.30.1
> > 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 12/13] gpio: Add support for Airoha EN7523 GPIO controller

[Felix Fietkau]

On 2021-12-05 00:57, Linus Walleij wrote:
> On Thu, Dec 2, 2021 at 6:59 PM Felix Fietkau <nbd@nbd.name> wrote:
> 
>> I just looked at the datasheet and the driver code again, and I think
>> EN7523 is too strange for proper generic GPIO support.
> 
> Yup I see that John explained it to me in the past, no problem.
> Let's do it like this then, but just drop select GPIO_GENERIC
> from KConfig since it's not used.
> 
> With that oneliner change:
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
> 
> Yours,
> Linus Walleij
The generic GPIO API is still used for the data register. The driver 
calls bgpio_init(), so you suggested oneliner change won't work.

- Felix

Re: [PATCH v5 12/13] gpio: Add support for Airoha EN7523 GPIO controller

[Felix Fietkau]

On 2021-12-05 00:57, Linus Walleij wrote:
> On Thu, Dec 2, 2021 at 6:59 PM Felix Fietkau <nbd@nbd.name> wrote:
> 
>> I just looked at the datasheet and the driver code again, and I think
>> EN7523 is too strange for proper generic GPIO support.
> 
> Yup I see that John explained it to me in the past, no problem.
> Let's do it like this then, but just drop select GPIO_GENERIC
> from KConfig since it's not used.
> 
> With that oneliner change:
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
> 
> Yours,
> Linus Walleij
The generic GPIO API is still used for the data register. The driver 
calls bgpio_init(), so you suggested oneliner change won't work.

- Felix

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 12/13] gpio: Add support for Airoha EN7523 GPIO controller

[Andy Shevchenko]

On Tue, Nov 30, 2021 at 1:08 AM Felix Fietkau <nbd@nbd.name> wrote:
>
> From: John Crispin <john@phrozen.org>
>
> Airoha's GPIO controller on their ARM EN7523 SoCs consists of two banks of 32
> GPIOs. Each instance in DT is for an single bank.

a single

...

> +/**
> + * airoha_gpio_ctrl - Airoha GPIO driver data

> + *

Unnecessary blank line.

> + * @gc: Associated gpio_chip instance.
> + * @data: The data register.
> + * @dir0: The direction register for the lower 16 pins.
> + * @dir1: The direction register for the higher 16 pins.
> + * @output: The output enable register.
> + */

...

> +static int airoha_dir_set(struct gpio_chip *gc, unsigned int gpio,
> +                         int val, int out)
> +{
> +       struct airoha_gpio_ctrl *ctrl = gc_to_ctrl(gc);
> +       u32 dir = ioread32(ctrl->dir[gpio / 16]);
> +       u32 output = ioread32(ctrl->output);
> +       u32 mask = BIT((gpio % 16) * 2);
> +
> +       if (out) {
> +               dir |= mask;
> +               output |= BIT(gpio);
> +       } else {
> +               dir &= ~mask;
> +               output &= ~BIT(gpio);
> +       }
> +
> +       iowrite32(dir, ctrl->dir[gpio / 16]);
> +       iowrite32(output, ctrl->output);

> +       if (out)
> +               gc->set(gc, gpio, val);

Needs a fix or a comment to explain why it's fine that there is a
glitch possible.

> +       return 0;
> +}

...

> +       err = bgpio_init(&ctrl->gc, dev, 4, ctrl->data, NULL,
> +                        NULL, NULL, NULL, 0);
> +       if (err) {

> +               dev_err(dev, "unable to init generic GPIO");
> +               return err;

return dev_err_probe(...);

> +       }

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v5 12/13] gpio: Add support for Airoha EN7523 GPIO controller

[Andy Shevchenko]

On Tue, Nov 30, 2021 at 1:08 AM Felix Fietkau <nbd@nbd.name> wrote:
>
> From: John Crispin <john@phrozen.org>
>
> Airoha's GPIO controller on their ARM EN7523 SoCs consists of two banks of 32
> GPIOs. Each instance in DT is for an single bank.

a single

...

> +/**
> + * airoha_gpio_ctrl - Airoha GPIO driver data

> + *

Unnecessary blank line.

> + * @gc: Associated gpio_chip instance.
> + * @data: The data register.
> + * @dir0: The direction register for the lower 16 pins.
> + * @dir1: The direction register for the higher 16 pins.
> + * @output: The output enable register.
> + */

...

> +static int airoha_dir_set(struct gpio_chip *gc, unsigned int gpio,
> +                         int val, int out)
> +{
> +       struct airoha_gpio_ctrl *ctrl = gc_to_ctrl(gc);
> +       u32 dir = ioread32(ctrl->dir[gpio / 16]);
> +       u32 output = ioread32(ctrl->output);
> +       u32 mask = BIT((gpio % 16) * 2);
> +
> +       if (out) {
> +               dir |= mask;
> +               output |= BIT(gpio);
> +       } else {
> +               dir &= ~mask;
> +               output &= ~BIT(gpio);
> +       }
> +
> +       iowrite32(dir, ctrl->dir[gpio / 16]);
> +       iowrite32(output, ctrl->output);

> +       if (out)
> +               gc->set(gc, gpio, val);

Needs a fix or a comment to explain why it's fine that there is a
glitch possible.

> +       return 0;
> +}

...

> +       err = bgpio_init(&ctrl->gc, dev, 4, ctrl->data, NULL,
> +                        NULL, NULL, NULL, 0);
> +       if (err) {

> +               dev_err(dev, "unable to init generic GPIO");
> +               return err;

return dev_err_probe(...);

> +       }

-- 
With Best Regards,
Andy Shevchenko

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel