[PATCH v2 1/2] mtd: spi-nor: core: Introduce SPI_NOR_SOFT_RESET flash_info fixup_flag

[PATCH v2 1/2] mtd: spi-nor: core: Introduce SPI_NOR_SOFT_RESET flash_info fixup_flag

[Tudor Ambarus]

The Soft Reset and Rescue Sequence Support is defined in BFPT_DWORD(16)
starting with JESD216A. The first version of SFDP, JESD216 (April 2011),
defines just the first 9 BFPT DWORDS, thus it does not contain information
about the Software Reset and Rescue Support. Since this support can not
be discovered by parsing the first SFDP version, introduce a flash_info
fixup_flag that will be used either by flashes that define
JESD216 (April 2011) or by flashes that do not define SFDP at all.
In case a flash defines BFPT_DWORD(16) but with wrong values, one should
instead use a post_bfpt() hook and set SNOR_F_SOFT_RESET.

Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
---
v2: collect R-b

 drivers/mtd/spi-nor/core.c | 3 +++
 drivers/mtd/spi-nor/core.h | 3 +++
 2 files changed, 6 insertions(+)

diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c
index 2e21d5ac0e2d..32d80fdaa2a2 100644
--- a/drivers/mtd/spi-nor/core.c
+++ b/drivers/mtd/spi-nor/core.c
@@ -2699,6 +2699,9 @@ static void spi_nor_init_fixup_flags(struct spi_nor *nor)
 
 	if (fixup_flags & SPI_NOR_IO_MODE_EN_VOLATILE)
 		nor->flags |= SNOR_F_IO_MODE_EN_VOLATILE;
+
+	if (fixup_flags & SPI_NOR_SOFT_RESET)
+		nor->flags |= SNOR_F_SOFT_RESET;
 }
 
 /**
diff --git a/drivers/mtd/spi-nor/core.h b/drivers/mtd/spi-nor/core.h
index 2afb610853a9..70c6bb7f5f04 100644
--- a/drivers/mtd/spi-nor/core.h
+++ b/drivers/mtd/spi-nor/core.h
@@ -373,6 +373,8 @@ struct spi_nor_fixups {
  *                            memory size above 128Mib.
  *   SPI_NOR_IO_MODE_EN_VOLATILE: flash enables the best available I/O mode
  *                            via a volatile bit.
+ *   SPI_NOR_SOFT_RESET:      flash supports software reset enable, reset
+ *                            sequence.
  * @mfr_flags:      manufacturer private flags. Used in the manufacturer fixup
  *                  hooks to differentiate support between flashes of the same
  *                  manufacturer.
@@ -416,6 +418,7 @@ struct flash_info {
 	u8 fixup_flags;
 #define SPI_NOR_4B_OPCODES		BIT(0)
 #define SPI_NOR_IO_MODE_EN_VOLATILE	BIT(1)
+#define SPI_NOR_SOFT_RESET		BIT(2)
 
 	u8 mfr_flags;
 
-- 
2.25.1

[PATCH v2 1/2] mtd: spi-nor: core: Introduce SPI_NOR_SOFT_RESET flash_info fixup_flag

[Tudor Ambarus]

The Soft Reset and Rescue Sequence Support is defined in BFPT_DWORD(16)
starting with JESD216A. The first version of SFDP, JESD216 (April 2011),
defines just the first 9 BFPT DWORDS, thus it does not contain information
about the Software Reset and Rescue Support. Since this support can not
be discovered by parsing the first SFDP version, introduce a flash_info
fixup_flag that will be used either by flashes that define
JESD216 (April 2011) or by flashes that do not define SFDP at all.
In case a flash defines BFPT_DWORD(16) but with wrong values, one should
instead use a post_bfpt() hook and set SNOR_F_SOFT_RESET.

Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
---
v2: collect R-b

 drivers/mtd/spi-nor/core.c | 3 +++
 drivers/mtd/spi-nor/core.h | 3 +++
 2 files changed, 6 insertions(+)

diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c
index 2e21d5ac0e2d..32d80fdaa2a2 100644
--- a/drivers/mtd/spi-nor/core.c
+++ b/drivers/mtd/spi-nor/core.c
@@ -2699,6 +2699,9 @@ static void spi_nor_init_fixup_flags(struct spi_nor *nor)
 
 	if (fixup_flags & SPI_NOR_IO_MODE_EN_VOLATILE)
 		nor->flags |= SNOR_F_IO_MODE_EN_VOLATILE;
+
+	if (fixup_flags & SPI_NOR_SOFT_RESET)
+		nor->flags |= SNOR_F_SOFT_RESET;
 }
 
 /**
diff --git a/drivers/mtd/spi-nor/core.h b/drivers/mtd/spi-nor/core.h
index 2afb610853a9..70c6bb7f5f04 100644
--- a/drivers/mtd/spi-nor/core.h
+++ b/drivers/mtd/spi-nor/core.h
@@ -373,6 +373,8 @@ struct spi_nor_fixups {
  *                            memory size above 128Mib.
  *   SPI_NOR_IO_MODE_EN_VOLATILE: flash enables the best available I/O mode
  *                            via a volatile bit.
+ *   SPI_NOR_SOFT_RESET:      flash supports software reset enable, reset
+ *                            sequence.
  * @mfr_flags:      manufacturer private flags. Used in the manufacturer fixup
  *                  hooks to differentiate support between flashes of the same
  *                  manufacturer.
@@ -416,6 +418,7 @@ struct flash_info {
 	u8 fixup_flags;
 #define SPI_NOR_4B_OPCODES		BIT(0)
 #define SPI_NOR_IO_MODE_EN_VOLATILE	BIT(1)
+#define SPI_NOR_SOFT_RESET		BIT(2)
 
 	u8 mfr_flags;
 
-- 
2.25.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH v2 2/2] mtd: spi-nor: macronix: Add support for mx66lm1g45g

[Tudor Ambarus]

mx66lm1g45g supports just 1-1-1, 8-8-8 and 8d-8d-8d modes. There are
versions of mx66lm1g45g which do not support SFDP, thus use
SPI_NOR_SKIP_SFDP. The RDID command issued through the octal peripheral
interface outputs data always in STR mode for whatever reason. Since
8d-8d-8s is not common, avoid reading the ID when enabling the octal dtr
mode. Instead, read back the CR2 to check if the switch was successful.
Tested in 1-1-1 and 8d-8d-8d modes using sama7g5 QSPI IP.

Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
---
v2:
- drop setting of dummy cycles, use the default value
- avoid odd lengths in octal dtr mode
- s/8d-8d-8d/8D-8D-8D

# cat /sys/devices/platform/soc/e080c000.spi/spi_master/spi1/spi1.0/spi-nor/jedec_id
c2853b
# cat /sys/devices/platform/soc/e080c000.spi/spi_master/spi1/spi1.0/spi-nor/manufacturer
macronix
# cat /sys/devices/platform/soc/e080c000.spi/spi_master/spi1/spi1.0/spi-nor/partname
mx66lm1g45g
# cat /sys/devices/platform/soc/e080c000.spi/spi_master/spi1/spi1.0/spi-nor/sfdp
cat: can't open '/sys/devices/platform/soc/e080c000.spi/spi_master/spi1/spi1.0/spi-nor/sfdp': No such file or directory

 drivers/mtd/spi-nor/macronix.c | 96 ++++++++++++++++++++++++++++++++++
 1 file changed, 96 insertions(+)

diff --git a/drivers/mtd/spi-nor/macronix.c b/drivers/mtd/spi-nor/macronix.c
index 67aaa83038b6..4c672deb1d1c 100644
--- a/drivers/mtd/spi-nor/macronix.c
+++ b/drivers/mtd/spi-nor/macronix.c
@@ -32,6 +32,95 @@ static struct spi_nor_fixups mx25l25635_fixups = {
 	.post_bfpt = mx25l25635_post_bfpt_fixups,
 };
 
+#define SPINOR_OP_READ_CR2		0x71
+#define SPINOR_OP_WRITE_CR2		0x72
+#define SPINOR_OP_MX_DTR_RD		0xee
+
+#define SPINOR_REG_CR2_MODE_ADDR	0
+#define SPINOR_REG_CR2_DTR_OPI_ENABLE	BIT(1)
+#define SPINOR_REG_CR2_SPI		0
+
+static int spi_nor_macronix_octal_dtr_enable(struct spi_nor *nor, bool enable)
+{
+	u8 *buf = nor->bouncebuf;
+	struct spi_mem_op op;
+	int ret;
+
+	/* Set/unset the octal and DTR enable bits. */
+	if (enable) {
+		buf[0] = SPINOR_REG_CR2_DTR_OPI_ENABLE;
+	} else {
+		/*
+		 * The register is one byte wide, but the one byte transactions
+		 * are not allowed in 8D-8D-8D mode. Since there is no register
+		 * at the next location, just initialize the value to zero and
+		 * let the transaction go on.
+		 */
+		buf[0] = SPINOR_REG_CR2_SPI;
+		buf[1] = 0;
+	}
+
+	op = (struct spi_mem_op)
+		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WRITE_CR2, 1),
+			   SPI_MEM_OP_ADDR(4, SPINOR_REG_CR2_MODE_ADDR, 1),
+			   SPI_MEM_OP_NO_DUMMY,
+			   SPI_MEM_OP_DATA_OUT(enable ? 1 : 2, buf, 1));
+	if (!enable)
+		spi_nor_spimem_setup_op(nor, &op, SNOR_PROTO_8_8_8_DTR);
+
+	ret = spi_nor_write_enable(nor);
+	if (ret)
+		return ret;
+
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret)
+		return ret;
+
+	/* Read back CR2 to make sure the switch was successful. */
+	op = (struct spi_mem_op)
+		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_READ_CR2, 1),
+			   SPI_MEM_OP_ADDR(4, SPINOR_REG_CR2_MODE_ADDR, 1),
+			   SPI_MEM_OP_DUMMY(enable ? 4 : 0, 1),
+			   SPI_MEM_OP_DATA_IN(enable ? 2 : 1, buf, 1));
+	if (enable)
+		spi_nor_spimem_setup_op(nor, &op, SNOR_PROTO_8_8_8_DTR);
+
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret)
+		return ret;
+
+	if (enable) {
+		if (buf[0] != SPINOR_REG_CR2_DTR_OPI_ENABLE) {
+			dev_dbg(nor->dev, "Failed to enable 8D-8D-8D mode.\n");
+			return -EINVAL;
+		}
+	} else if (buf[0] != SPINOR_REG_CR2_SPI) {
+		dev_dbg(nor->dev, "Failed to disable 8D-8D-8D mode.\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static void mx66lm1g45g_late_init(struct spi_nor *nor)
+{
+	nor->params->octal_dtr_enable = spi_nor_macronix_octal_dtr_enable;
+
+	/* Set the Fast Read settings. */
+	nor->params->hwcaps.mask |= SNOR_HWCAPS_READ_8_8_8_DTR;
+	spi_nor_set_read_settings(&nor->params->reads[SNOR_CMD_READ_8_8_8_DTR],
+				  0, 20, SPINOR_OP_MX_DTR_RD,
+				  SNOR_PROTO_8_8_8_DTR);
+
+	nor->cmd_ext_type = SPI_NOR_EXT_INVERT;
+	nor->params->rdsr_dummy = 4;
+	nor->params->rdsr_addr_nbytes = 4;
+}
+
+static struct spi_nor_fixups mx66lm1g45g_fixups = {
+	.late_init = mx66lm1g45g_late_init,
+};
+
 static const struct flash_info macronix_parts[] = {
 	/* Macronix */
 	{ "mx25l512e",   INFO(0xc22010, 0, 64 * 1024,   1)
@@ -100,6 +189,13 @@ static const struct flash_info macronix_parts[] = {
 	{ "mx66u2g45g",	 INFO(0xc2253c, 0, 64 * 1024, 4096)
 		NO_SFDP_FLAGS(SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ)
 		FIXUP_FLAGS(SPI_NOR_4B_OPCODES) },
+	{ "mx66lm1g45g", INFO(0xc2853b, 0, 64 * 1024, 2048)
+		NO_SFDP_FLAGS(SPI_NOR_SKIP_SFDP | SECT_4K |
+			      SPI_NOR_OCTAL_DTR_READ | SPI_NOR_OCTAL_DTR_PP)
+		FIXUP_FLAGS(SPI_NOR_4B_OPCODES | SPI_NOR_IO_MODE_EN_VOLATILE |
+			    SPI_NOR_SOFT_RESET)
+		.fixups = &mx66lm1g45g_fixups,
+	},
 };
 
 static void macronix_default_init(struct spi_nor *nor)
-- 
2.25.1

[PATCH v2 2/2] mtd: spi-nor: macronix: Add support for mx66lm1g45g

[Tudor Ambarus]

mx66lm1g45g supports just 1-1-1, 8-8-8 and 8d-8d-8d modes. There are
versions of mx66lm1g45g which do not support SFDP, thus use
SPI_NOR_SKIP_SFDP. The RDID command issued through the octal peripheral
interface outputs data always in STR mode for whatever reason. Since
8d-8d-8s is not common, avoid reading the ID when enabling the octal dtr
mode. Instead, read back the CR2 to check if the switch was successful.
Tested in 1-1-1 and 8d-8d-8d modes using sama7g5 QSPI IP.

Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
---
v2:
- drop setting of dummy cycles, use the default value
- avoid odd lengths in octal dtr mode
- s/8d-8d-8d/8D-8D-8D

# cat /sys/devices/platform/soc/e080c000.spi/spi_master/spi1/spi1.0/spi-nor/jedec_id
c2853b
# cat /sys/devices/platform/soc/e080c000.spi/spi_master/spi1/spi1.0/spi-nor/manufacturer
macronix
# cat /sys/devices/platform/soc/e080c000.spi/spi_master/spi1/spi1.0/spi-nor/partname
mx66lm1g45g
# cat /sys/devices/platform/soc/e080c000.spi/spi_master/spi1/spi1.0/spi-nor/sfdp
cat: can't open '/sys/devices/platform/soc/e080c000.spi/spi_master/spi1/spi1.0/spi-nor/sfdp': No such file or directory

 drivers/mtd/spi-nor/macronix.c | 96 ++++++++++++++++++++++++++++++++++
 1 file changed, 96 insertions(+)

diff --git a/drivers/mtd/spi-nor/macronix.c b/drivers/mtd/spi-nor/macronix.c
index 67aaa83038b6..4c672deb1d1c 100644
--- a/drivers/mtd/spi-nor/macronix.c
+++ b/drivers/mtd/spi-nor/macronix.c
@@ -32,6 +32,95 @@ static struct spi_nor_fixups mx25l25635_fixups = {
 	.post_bfpt = mx25l25635_post_bfpt_fixups,
 };
 
+#define SPINOR_OP_READ_CR2		0x71
+#define SPINOR_OP_WRITE_CR2		0x72
+#define SPINOR_OP_MX_DTR_RD		0xee
+
+#define SPINOR_REG_CR2_MODE_ADDR	0
+#define SPINOR_REG_CR2_DTR_OPI_ENABLE	BIT(1)
+#define SPINOR_REG_CR2_SPI		0
+
+static int spi_nor_macronix_octal_dtr_enable(struct spi_nor *nor, bool enable)
+{
+	u8 *buf = nor->bouncebuf;
+	struct spi_mem_op op;
+	int ret;
+
+	/* Set/unset the octal and DTR enable bits. */
+	if (enable) {
+		buf[0] = SPINOR_REG_CR2_DTR_OPI_ENABLE;
+	} else {
+		/*
+		 * The register is one byte wide, but the one byte transactions
+		 * are not allowed in 8D-8D-8D mode. Since there is no register
+		 * at the next location, just initialize the value to zero and
+		 * let the transaction go on.
+		 */
+		buf[0] = SPINOR_REG_CR2_SPI;
+		buf[1] = 0;
+	}
+
+	op = (struct spi_mem_op)
+		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WRITE_CR2, 1),
+			   SPI_MEM_OP_ADDR(4, SPINOR_REG_CR2_MODE_ADDR, 1),
+			   SPI_MEM_OP_NO_DUMMY,
+			   SPI_MEM_OP_DATA_OUT(enable ? 1 : 2, buf, 1));
+	if (!enable)
+		spi_nor_spimem_setup_op(nor, &op, SNOR_PROTO_8_8_8_DTR);
+
+	ret = spi_nor_write_enable(nor);
+	if (ret)
+		return ret;
+
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret)
+		return ret;
+
+	/* Read back CR2 to make sure the switch was successful. */
+	op = (struct spi_mem_op)
+		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_READ_CR2, 1),
+			   SPI_MEM_OP_ADDR(4, SPINOR_REG_CR2_MODE_ADDR, 1),
+			   SPI_MEM_OP_DUMMY(enable ? 4 : 0, 1),
+			   SPI_MEM_OP_DATA_IN(enable ? 2 : 1, buf, 1));
+	if (enable)
+		spi_nor_spimem_setup_op(nor, &op, SNOR_PROTO_8_8_8_DTR);
+
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret)
+		return ret;
+
+	if (enable) {
+		if (buf[0] != SPINOR_REG_CR2_DTR_OPI_ENABLE) {
+			dev_dbg(nor->dev, "Failed to enable 8D-8D-8D mode.\n");
+			return -EINVAL;
+		}
+	} else if (buf[0] != SPINOR_REG_CR2_SPI) {
+		dev_dbg(nor->dev, "Failed to disable 8D-8D-8D mode.\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static void mx66lm1g45g_late_init(struct spi_nor *nor)
+{
+	nor->params->octal_dtr_enable = spi_nor_macronix_octal_dtr_enable;
+
+	/* Set the Fast Read settings. */
+	nor->params->hwcaps.mask |= SNOR_HWCAPS_READ_8_8_8_DTR;
+	spi_nor_set_read_settings(&nor->params->reads[SNOR_CMD_READ_8_8_8_DTR],
+				  0, 20, SPINOR_OP_MX_DTR_RD,
+				  SNOR_PROTO_8_8_8_DTR);
+
+	nor->cmd_ext_type = SPI_NOR_EXT_INVERT;
+	nor->params->rdsr_dummy = 4;
+	nor->params->rdsr_addr_nbytes = 4;
+}
+
+static struct spi_nor_fixups mx66lm1g45g_fixups = {
+	.late_init = mx66lm1g45g_late_init,
+};
+
 static const struct flash_info macronix_parts[] = {
 	/* Macronix */
 	{ "mx25l512e",   INFO(0xc22010, 0, 64 * 1024,   1)
@@ -100,6 +189,13 @@ static const struct flash_info macronix_parts[] = {
 	{ "mx66u2g45g",	 INFO(0xc2253c, 0, 64 * 1024, 4096)
 		NO_SFDP_FLAGS(SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ)
 		FIXUP_FLAGS(SPI_NOR_4B_OPCODES) },
+	{ "mx66lm1g45g", INFO(0xc2853b, 0, 64 * 1024, 2048)
+		NO_SFDP_FLAGS(SPI_NOR_SKIP_SFDP | SECT_4K |
+			      SPI_NOR_OCTAL_DTR_READ | SPI_NOR_OCTAL_DTR_PP)
+		FIXUP_FLAGS(SPI_NOR_4B_OPCODES | SPI_NOR_IO_MODE_EN_VOLATILE |
+			    SPI_NOR_SOFT_RESET)
+		.fixups = &mx66lm1g45g_fixups,
+	},
 };
 
 static void macronix_default_init(struct spi_nor *nor)
-- 
2.25.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v2 1/2] mtd: spi-nor: core: Introduce SPI_NOR_SOFT_RESET flash_info fixup_flag

[Pratyush Yadav]

On 09/12/21 09:04PM, Tudor Ambarus wrote:
> The Soft Reset and Rescue Sequence Support is defined in BFPT_DWORD(16)
> starting with JESD216A. The first version of SFDP, JESD216 (April 2011),
> defines just the first 9 BFPT DWORDS, thus it does not contain information
> about the Software Reset and Rescue Support. Since this support can not
> be discovered by parsing the first SFDP version, introduce a flash_info
> fixup_flag that will be used either by flashes that define
> JESD216 (April 2011) or by flashes that do not define SFDP at all.
> In case a flash defines BFPT_DWORD(16) but with wrong values, one should
> instead use a post_bfpt() hook and set SNOR_F_SOFT_RESET.
> 
> Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

Reviewed-by: Pratyush Yadav <p.yadav@ti.com>

-- 
Regards,
Pratyush Yadav
Texas Instruments Inc.

Re: [PATCH v2 1/2] mtd: spi-nor: core: Introduce SPI_NOR_SOFT_RESET flash_info fixup_flag

[Pratyush Yadav]

On 09/12/21 09:04PM, Tudor Ambarus wrote:
> The Soft Reset and Rescue Sequence Support is defined in BFPT_DWORD(16)
> starting with JESD216A. The first version of SFDP, JESD216 (April 2011),
> defines just the first 9 BFPT DWORDS, thus it does not contain information
> about the Software Reset and Rescue Support. Since this support can not
> be discovered by parsing the first SFDP version, introduce a flash_info
> fixup_flag that will be used either by flashes that define
> JESD216 (April 2011) or by flashes that do not define SFDP at all.
> In case a flash defines BFPT_DWORD(16) but with wrong values, one should
> instead use a post_bfpt() hook and set SNOR_F_SOFT_RESET.
> 
> Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

Reviewed-by: Pratyush Yadav <p.yadav@ti.com>

-- 
Regards,
Pratyush Yadav
Texas Instruments Inc.

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH v2 1/2] mtd: spi-nor: core: Introduce SPI_NOR_SOFT_RESET flash_info fixup_flag

[Tudor Ambarus]

The Soft Reset and Rescue Sequence Support is defined in BFPT_DWORD(16)
starting with JESD216A. The first version of SFDP, JESD216 (April 2011),
defines just the first 9 BFPT DWORDS, thus it does not contain information
about the Software Reset and Rescue Support. Since this support can not
be discovered by parsing the first SFDP version, introduce a flash_info
fixup_flag that will be used either by flashes that define
JESD216 (April 2011) or by flashes that do not define SFDP at all.
In case a flash defines BFPT_DWORD(16) but with wrong values, one should
instead use a post_bfpt() hook and set SNOR_F_SOFT_RESET.

Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
---
v2: no changes

 drivers/mtd/spi-nor/core.c | 3 +++
 drivers/mtd/spi-nor/core.h | 3 +++
 2 files changed, 6 insertions(+)

diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c
index 2e21d5ac0e2d..32d80fdaa2a2 100644
--- a/drivers/mtd/spi-nor/core.c
+++ b/drivers/mtd/spi-nor/core.c
@@ -2699,6 +2699,9 @@ static void spi_nor_init_fixup_flags(struct spi_nor *nor)
 
 	if (fixup_flags & SPI_NOR_IO_MODE_EN_VOLATILE)
 		nor->flags |= SNOR_F_IO_MODE_EN_VOLATILE;
+
+	if (fixup_flags & SPI_NOR_SOFT_RESET)
+		nor->flags |= SNOR_F_SOFT_RESET;
 }
 
 /**
diff --git a/drivers/mtd/spi-nor/core.h b/drivers/mtd/spi-nor/core.h
index 2afb610853a9..70c6bb7f5f04 100644
--- a/drivers/mtd/spi-nor/core.h
+++ b/drivers/mtd/spi-nor/core.h
@@ -373,6 +373,8 @@ struct spi_nor_fixups {
  *                            memory size above 128Mib.
  *   SPI_NOR_IO_MODE_EN_VOLATILE: flash enables the best available I/O mode
  *                            via a volatile bit.
+ *   SPI_NOR_SOFT_RESET:      flash supports software reset enable, reset
+ *                            sequence.
  * @mfr_flags:      manufacturer private flags. Used in the manufacturer fixup
  *                  hooks to differentiate support between flashes of the same
  *                  manufacturer.
@@ -416,6 +418,7 @@ struct flash_info {
 	u8 fixup_flags;
 #define SPI_NOR_4B_OPCODES		BIT(0)
 #define SPI_NOR_IO_MODE_EN_VOLATILE	BIT(1)
+#define SPI_NOR_SOFT_RESET		BIT(2)
 
 	u8 mfr_flags;
 
-- 
2.25.1

[PATCH v2 1/2] mtd: spi-nor: core: Introduce SPI_NOR_SOFT_RESET flash_info fixup_flag

[Tudor Ambarus]

The Soft Reset and Rescue Sequence Support is defined in BFPT_DWORD(16)
starting with JESD216A. The first version of SFDP, JESD216 (April 2011),
defines just the first 9 BFPT DWORDS, thus it does not contain information
about the Software Reset and Rescue Support. Since this support can not
be discovered by parsing the first SFDP version, introduce a flash_info
fixup_flag that will be used either by flashes that define
JESD216 (April 2011) or by flashes that do not define SFDP at all.
In case a flash defines BFPT_DWORD(16) but with wrong values, one should
instead use a post_bfpt() hook and set SNOR_F_SOFT_RESET.

Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
---
v2: no changes

 drivers/mtd/spi-nor/core.c | 3 +++
 drivers/mtd/spi-nor/core.h | 3 +++
 2 files changed, 6 insertions(+)

diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c
index 2e21d5ac0e2d..32d80fdaa2a2 100644
--- a/drivers/mtd/spi-nor/core.c
+++ b/drivers/mtd/spi-nor/core.c
@@ -2699,6 +2699,9 @@ static void spi_nor_init_fixup_flags(struct spi_nor *nor)
 
 	if (fixup_flags & SPI_NOR_IO_MODE_EN_VOLATILE)
 		nor->flags |= SNOR_F_IO_MODE_EN_VOLATILE;
+
+	if (fixup_flags & SPI_NOR_SOFT_RESET)
+		nor->flags |= SNOR_F_SOFT_RESET;
 }
 
 /**
diff --git a/drivers/mtd/spi-nor/core.h b/drivers/mtd/spi-nor/core.h
index 2afb610853a9..70c6bb7f5f04 100644
--- a/drivers/mtd/spi-nor/core.h
+++ b/drivers/mtd/spi-nor/core.h
@@ -373,6 +373,8 @@ struct spi_nor_fixups {
  *                            memory size above 128Mib.
  *   SPI_NOR_IO_MODE_EN_VOLATILE: flash enables the best available I/O mode
  *                            via a volatile bit.
+ *   SPI_NOR_SOFT_RESET:      flash supports software reset enable, reset
+ *                            sequence.
  * @mfr_flags:      manufacturer private flags. Used in the manufacturer fixup
  *                  hooks to differentiate support between flashes of the same
  *                  manufacturer.
@@ -416,6 +418,7 @@ struct flash_info {
 	u8 fixup_flags;
 #define SPI_NOR_4B_OPCODES		BIT(0)
 #define SPI_NOR_IO_MODE_EN_VOLATILE	BIT(1)
+#define SPI_NOR_SOFT_RESET		BIT(2)
 
 	u8 mfr_flags;
 
-- 
2.25.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/