* [PATCH v2 1/7] mfd: qcom-spmi-pmic: expose the PMIC revid information to clients
2022-01-05 18:33 [PATCH v2 0/7] iio: adc: introduce Qualcomm SPMI Round Robin ADC Caleb Connolly
@ 2022-01-05 18:33 ` Caleb Connolly
2022-01-05 18:33 ` [PATCH v2 2/7] dt-bindings: iio: adc: document qcom-spmi-rradc Caleb Connolly
` (5 subsequent siblings)
6 siblings, 0 replies; 10+ messages in thread
From: Caleb Connolly @ 2022-01-05 18:33 UTC (permalink / raw)
To: caleb.connolly, Jonathan Cameron, Lars-Peter Clausen,
Rob Herring, Andy Gross, Bjorn Andersson, Lee Jones, linux-iio,
devicetree, linux-kernel, linux-arm-msm
Cc: sumit.semwal, amit.pundir, john.stultz
Some PMIC functions such as the RRADC need to be aware of the PMIC
chip revision information to implement errata or otherwise adjust
behaviour, export the PMIC information to enable this.
This is specifically required to enable the RRADC to adjust
coefficients based on which chip fab the PMIC was produced in,
this can vary per unique device and therefore has to be read at
runtime.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
---
drivers/mfd/qcom-spmi-pmic.c | 108 +++++++++++++++++------------------
include/soc/qcom/qcom-pmic.h | 63 ++++++++++++++++++++
2 files changed, 114 insertions(+), 57 deletions(-)
create mode 100644 include/soc/qcom/qcom-pmic.h
diff --git a/drivers/mfd/qcom-spmi-pmic.c b/drivers/mfd/qcom-spmi-pmic.c
index 1cacc00aa6c9..6b75c2f52b74 100644
--- a/drivers/mfd/qcom-spmi-pmic.c
+++ b/drivers/mfd/qcom-spmi-pmic.c
@@ -3,51 +3,24 @@
* Copyright (c) 2014, The Linux Foundation. All rights reserved.
*/
+#include <linux/device.h>
+#include <linux/gfp.h>
#include <linux/kernel.h>
#include <linux/module.h>
+#include <linux/slab.h>
#include <linux/spmi.h>
#include <linux/regmap.h>
#include <linux/of_platform.h>
+#include <soc/qcom/qcom-pmic.h>
#define PMIC_REV2 0x101
#define PMIC_REV3 0x102
#define PMIC_REV4 0x103
#define PMIC_TYPE 0x104
#define PMIC_SUBTYPE 0x105
-
+#define PMIC_FAB_ID 0x1f2
#define PMIC_TYPE_VALUE 0x51
-#define COMMON_SUBTYPE 0x00
-#define PM8941_SUBTYPE 0x01
-#define PM8841_SUBTYPE 0x02
-#define PM8019_SUBTYPE 0x03
-#define PM8226_SUBTYPE 0x04
-#define PM8110_SUBTYPE 0x05
-#define PMA8084_SUBTYPE 0x06
-#define PMI8962_SUBTYPE 0x07
-#define PMD9635_SUBTYPE 0x08
-#define PM8994_SUBTYPE 0x09
-#define PMI8994_SUBTYPE 0x0a
-#define PM8916_SUBTYPE 0x0b
-#define PM8004_SUBTYPE 0x0c
-#define PM8909_SUBTYPE 0x0d
-#define PM8028_SUBTYPE 0x0e
-#define PM8901_SUBTYPE 0x0f
-#define PM8950_SUBTYPE 0x10
-#define PMI8950_SUBTYPE 0x11
-#define PM8998_SUBTYPE 0x14
-#define PMI8998_SUBTYPE 0x15
-#define PM8005_SUBTYPE 0x18
-#define PM660L_SUBTYPE 0x1A
-#define PM660_SUBTYPE 0x1B
-#define PM8150_SUBTYPE 0x1E
-#define PM8150L_SUBTYPE 0x1f
-#define PM8150B_SUBTYPE 0x20
-#define PMK8002_SUBTYPE 0x21
-#define PM8009_SUBTYPE 0x24
-#define PM8150C_SUBTYPE 0x26
-#define SMB2351_SUBTYPE 0x29
-
static const struct of_device_id pmic_spmi_id_table[] = {
{ .compatible = "qcom,pm660", .data = (void *)PM660_SUBTYPE },
{ .compatible = "qcom,pm660l", .data = (void *)PM660L_SUBTYPE },
@@ -81,42 +54,47 @@ static const struct of_device_id pmic_spmi_id_table[] = {
{ }
};
-static void pmic_spmi_show_revid(struct regmap *map, struct device *dev)
+static int pmic_spmi_load_revid(struct regmap *map, struct device *dev,
+ struct qcom_spmi_pmic *pmic)
{
- unsigned int rev2, minor, major, type, subtype;
- const char *name = "unknown";
int ret, i;
- ret = regmap_read(map, PMIC_TYPE, &type);
+ ret = regmap_read(map, PMIC_TYPE, &pmic->type);
if (ret < 0)
- return;
+ return ret;
- if (type != PMIC_TYPE_VALUE)
- return;
+ if (pmic->type != PMIC_TYPE_VALUE)
+ return ret;
- ret = regmap_read(map, PMIC_SUBTYPE, &subtype);
+ ret = regmap_read(map, PMIC_SUBTYPE, &pmic->subtype);
if (ret < 0)
- return;
+ return ret;
for (i = 0; i < ARRAY_SIZE(pmic_spmi_id_table); i++) {
- if (subtype == (unsigned long)pmic_spmi_id_table[i].data)
+ if (pmic->subtype == (unsigned long)pmic_spmi_id_table[i].data)
break;
}
if (i != ARRAY_SIZE(pmic_spmi_id_table))
- name = pmic_spmi_id_table[i].compatible;
+ pmic->name = devm_kstrdup_const(dev, pmic_spmi_id_table[i].compatible, GFP_KERNEL);
- ret = regmap_read(map, PMIC_REV2, &rev2);
+ ret = regmap_read(map, PMIC_REV2, &pmic->rev2);
if (ret < 0)
- return;
+ return ret;
- ret = regmap_read(map, PMIC_REV3, &minor);
+ ret = regmap_read(map, PMIC_REV3, &pmic->minor);
if (ret < 0)
- return;
+ return ret;
- ret = regmap_read(map, PMIC_REV4, &major);
+ ret = regmap_read(map, PMIC_REV4, &pmic->major);
if (ret < 0)
- return;
+ return ret;
+
+ if (pmic->subtype == PMI8998_SUBTYPE || pmic->subtype == PM660_SUBTYPE) {
+ ret = regmap_read(map, PMIC_FAB_ID, &pmic->fab_id);
+ if (ret < 0)
+ return ret;
+ }
/*
* In early versions of PM8941 and PM8226, the major revision number
@@ -124,14 +102,14 @@ static void pmic_spmi_show_revid(struct regmap *map, struct device *dev)
* Increment the major revision number here if the chip is an early
* version of PM8941 or PM8226.
*/
- if ((subtype == PM8941_SUBTYPE || subtype == PM8226_SUBTYPE) &&
- major < 0x02)
- major++;
+ if ((pmic->subtype == PM8941_SUBTYPE || pmic->subtype == PM8226_SUBTYPE) &&
+ pmic->major < 0x02)
+ pmic->major++;
- if (subtype == PM8110_SUBTYPE)
- minor = rev2;
+ if (pmic->subtype == PM8110_SUBTYPE)
+ pmic->minor = pmic->rev2;
- dev_dbg(dev, "%x: %s v%d.%d\n", subtype, name, major, minor);
+ return 0;
}
static const struct regmap_config spmi_regmap_config = {
@@ -144,22 +122,38 @@ static const struct regmap_config spmi_regmap_config = {
static int pmic_spmi_probe(struct spmi_device *sdev)
{
struct regmap *regmap;
+ struct qcom_spmi_pmic *pmic;
regmap = devm_regmap_init_spmi_ext(sdev, &spmi_regmap_config);
if (IS_ERR(regmap))
return PTR_ERR(regmap);
+ pmic = devm_kzalloc(&sdev->dev, sizeof(*pmic), GFP_KERNEL);
+ if (!pmic)
+ return -ENOMEM;
+
/* Only the first slave id for a PMIC contains this information */
- if (sdev->usid % 2 == 0)
- pmic_spmi_show_revid(regmap, &sdev->dev);
+ if (sdev->usid % 2 == 0) {
+ pmic_spmi_load_revid(regmap, &sdev->dev, pmic);
+ spmi_device_set_drvdata(sdev, pmic);
+ qcom_pmic_print_info(&sdev->dev, pmic);
+ }
return devm_of_platform_populate(&sdev->dev);
}
+static void pmic_spmi_remove(struct spmi_device *sdev)
+{
+ struct qcom_spmi_pmic *pmic = spmi_device_get_drvdata(sdev);
+
+ kfree(pmic->name);
+}
+
MODULE_DEVICE_TABLE(of, pmic_spmi_id_table);
static struct spmi_driver pmic_spmi_driver = {
.probe = pmic_spmi_probe,
+ .remove = pmic_spmi_remove,
.driver = {
.name = "pmic-spmi",
.of_match_table = pmic_spmi_id_table,
diff --git a/include/soc/qcom/qcom-pmic.h b/include/soc/qcom/qcom-pmic.h
new file mode 100644
index 000000000000..59114988582d
--- /dev/null
+++ b/include/soc/qcom/qcom-pmic.h
@@ -0,0 +1,63 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* Copyright (c) 2021 Linaro. All rights reserved.
+ * Copyright (c) 2021 Caleb Connolly <caleb.connolly@linaro.org>
+ */
+
+#ifndef __QCOM_PMIC_H__
+#define __QCOM_PMIC_H__
+
+#define COMMON_SUBTYPE 0x00
+#define PM8941_SUBTYPE 0x01
+#define PM8841_SUBTYPE 0x02
+#define PM8019_SUBTYPE 0x03
+#define PM8226_SUBTYPE 0x04
+#define PM8110_SUBTYPE 0x05
+#define PMA8084_SUBTYPE 0x06
+#define PMI8962_SUBTYPE 0x07
+#define PMD9635_SUBTYPE 0x08
+#define PM8994_SUBTYPE 0x09
+#define PMI8994_SUBTYPE 0x0a
+#define PM8916_SUBTYPE 0x0b
+#define PM8004_SUBTYPE 0x0c
+#define PM8909_SUBTYPE 0x0d
+#define PM8028_SUBTYPE 0x0e
+#define PM8901_SUBTYPE 0x0f
+#define PM8950_SUBTYPE 0x10
+#define PMI8950_SUBTYPE 0x11
+#define PM8998_SUBTYPE 0x14
+#define PMI8998_SUBTYPE 0x15
+#define PM8005_SUBTYPE 0x18
+#define PM660L_SUBTYPE 0x1A
+#define PM660_SUBTYPE 0x1B
+#define PM8150_SUBTYPE 0x1E
+#define PM8150L_SUBTYPE 0x1f
+#define PM8150B_SUBTYPE 0x20
+#define PMK8002_SUBTYPE 0x21
+#define PM8009_SUBTYPE 0x24
+#define PM8150C_SUBTYPE 0x26
+#define SMB2351_SUBTYPE 0x29
+
+#define PMI8998_FAB_ID_SMIC 0x11
+#define PMI8998_FAB_ID_GF 0x30
+
+#define PM660_FAB_ID_GF 0x0
+#define PM660_FAB_ID_TSMC 0x2
+#define PM660_FAB_ID_MX 0x3
+
+struct qcom_spmi_pmic {
+ unsigned int type;
+ unsigned int subtype;
+ unsigned int major;
+ unsigned int minor;
+ unsigned int rev2;
+ unsigned int fab_id;
+ const char *name;
+};
+
+static inline void qcom_pmic_print_info(struct device *dev, struct qcom_spmi_pmic *pmic)
+{
+ dev_info(dev, "%x: %s v%d.%d\n",
+ pmic->subtype, pmic->name, pmic->major, pmic->minor);
+}
+
+#endif /* __QCOM_PMIC_H__ */
--
2.34.1
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH v2 3/7] iio: adc: qcom-spmi-rradc: introduce round robin adc
2022-01-05 18:33 [PATCH v2 0/7] iio: adc: introduce Qualcomm SPMI Round Robin ADC Caleb Connolly
2022-01-05 18:33 ` [PATCH v2 1/7] mfd: qcom-spmi-pmic: expose the PMIC revid information to clients Caleb Connolly
2022-01-05 18:33 ` [PATCH v2 2/7] dt-bindings: iio: adc: document qcom-spmi-rradc Caleb Connolly
@ 2022-01-05 18:33 ` Caleb Connolly
2022-01-05 21:05 ` kernel test robot
2022-01-05 18:33 ` [PATCH v2 4/7] arm64: dts: qcom: pmi8998: add rradc node Caleb Connolly
` (3 subsequent siblings)
6 siblings, 1 reply; 10+ messages in thread
From: Caleb Connolly @ 2022-01-05 18:33 UTC (permalink / raw)
To: caleb.connolly, Jonathan Cameron, Lars-Peter Clausen,
Rob Herring, Andy Gross, Bjorn Andersson, Lee Jones, linux-iio,
devicetree, linux-kernel, linux-arm-msm
Cc: sumit.semwal, amit.pundir, john.stultz
The Round Robin ADC is responsible for reading data about the rate of
charge from the USB or DC in jacks, it can also read the battery
ID (resistence) and some temperatures. It is found on the PMI8998 and
PM660 Qualcomm PMICs.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
---
drivers/iio/adc/Kconfig | 13 +
drivers/iio/adc/Makefile | 1 +
drivers/iio/adc/qcom-spmi-rradc.c | 1070 +++++++++++++++++++++++++++++
3 files changed, 1084 insertions(+)
create mode 100644 drivers/iio/adc/qcom-spmi-rradc.c
diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 3363af15a43f..37f18ee4c4c5 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -812,6 +812,19 @@ config QCOM_PM8XXX_XOADC
To compile this driver as a module, choose M here: the module
will be called qcom-pm8xxx-xoadc.
+config QCOM_SPMI_RRADC
+ tristate "Qualcomm SPMI RRADC"
+ depends on MFD_SPMI_PMIC
+ help
+ This is for the PMIC Round Robin ADC driver.
+
+ This driver exposes the battery ID resistor, battery thermal, PMIC die
+ temperature, charger USB in and DC in voltage and current.
+
+ To compile this driver as a module, choose M here: the module will
+ be called qcom-qpmi-rradc.
+
+
config QCOM_SPMI_IADC
tristate "Qualcomm SPMI PMIC current ADC"
depends on SPMI
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index d3f53549720c..ca8bad549175 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -77,6 +77,7 @@ obj-$(CONFIG_NPCM_ADC) += npcm_adc.o
obj-$(CONFIG_PALMAS_GPADC) += palmas_gpadc.o
obj-$(CONFIG_QCOM_SPMI_ADC5) += qcom-spmi-adc5.o
obj-$(CONFIG_QCOM_SPMI_IADC) += qcom-spmi-iadc.o
+obj-$(CONFIG_QCOM_SPMI_RRADC) += qcom-spmi-rradc.o
obj-$(CONFIG_QCOM_VADC_COMMON) += qcom-vadc-common.o
obj-$(CONFIG_QCOM_SPMI_VADC) += qcom-spmi-vadc.o
obj-$(CONFIG_QCOM_PM8XXX_XOADC) += qcom-pm8xxx-xoadc.o
diff --git a/drivers/iio/adc/qcom-spmi-rradc.c b/drivers/iio/adc/qcom-spmi-rradc.c
new file mode 100644
index 000000000000..e5c3b249bc0f
--- /dev/null
+++ b/drivers/iio/adc/qcom-spmi-rradc.c
@@ -0,0 +1,1070 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2021 Linaro Limited.
+ * Author: Caleb Connolly <caleb.connolly@linaro.org>
+ *
+ * This driver is for the Round Robin ADC found in the pmi8998 and pm660 PMICs.
+ */
+
+#include <linux/delay.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/types.h>
+#include <linux/kernel.h>
+#include <linux/math64.h>
+#include <linux/minmax.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/power_supply.h>
+#include <linux/regmap.h>
+#include <linux/spmi.h>
+#include <linux/types.h>
+#include <asm-generic/unaligned.h>
+#include <linux/units.h>
+#include <soc/qcom/qcom-pmic.h>
+
+#define RR_ADC_EN_CTL 0x46
+#define RR_ADC_SKIN_TEMP_LSB 0x50
+#define RR_ADC_SKIN_TEMP_MSB 0x51
+#define RR_ADC_RR_ADC_CTL 0x52
+#define RR_ADC_ADC_CTL_CONTINUOUS_SEL BIT(3)
+#define RR_ADC_ADC_LOG 0x53
+#define RR_ADC_ADC_LOG_CLR_CTRL BIT(0)
+
+#define RR_ADC_FAKE_BATT_LOW_LSB 0x58
+#define RR_ADC_FAKE_BATT_LOW_MSB 0x59
+#define RR_ADC_FAKE_BATT_HIGH_LSB 0x5A
+#define RR_ADC_FAKE_BATT_HIGH_MSB 0x5B
+
+#define RR_ADC_BATT_ID_CTRL 0x60
+#define RR_ADC_BATT_ID_CTRL_CHANNEL_CONV BIT(0)
+#define RR_ADC_BATT_ID_TRIGGER 0x61
+#define RR_ADC_BATT_ID_STS 0x62
+#define RR_ADC_BATT_ID_CFG 0x63
+#define BATT_ID_SETTLE_MASK GENMASK(7, 5)
+#define RR_ADC_BATT_ID_5_LSB 0x66
+#define RR_ADC_BATT_ID_5_MSB 0x67
+#define RR_ADC_BATT_ID_15_LSB 0x68
+#define RR_ADC_BATT_ID_15_MSB 0x69
+#define RR_ADC_BATT_ID_150_LSB 0x6A
+#define RR_ADC_BATT_ID_150_MSB 0x6B
+
+#define RR_ADC_BATT_THERM_CTRL 0x70
+#define RR_ADC_BATT_THERM_TRIGGER 0x71
+#define RR_ADC_BATT_THERM_STS 0x72
+#define RR_ADC_BATT_THERM_CFG 0x73
+#define RR_ADC_BATT_THERM_LSB 0x74
+#define RR_ADC_BATT_THERM_MSB 0x75
+#define RR_ADC_BATT_THERM_FREQ 0x76
+
+#define RR_ADC_AUX_THERM_CTRL 0x80
+#define RR_ADC_AUX_THERM_TRIGGER 0x81
+#define RR_ADC_AUX_THERM_STS 0x82
+#define RR_ADC_AUX_THERM_CFG 0x83
+#define RR_ADC_AUX_THERM_LSB 0x84
+#define RR_ADC_AUX_THERM_MSB 0x85
+
+#define RR_ADC_SKIN_HOT 0x86
+#define RR_ADC_SKIN_TOO_HOT 0x87
+
+#define RR_ADC_AUX_THERM_C1 0x88
+#define RR_ADC_AUX_THERM_C2 0x89
+#define RR_ADC_AUX_THERM_C3 0x8A
+#define RR_ADC_AUX_THERM_HALF_RANGE 0x8B
+
+#define RR_ADC_USB_IN_V_CTRL 0x90
+#define RR_ADC_USB_IN_V_TRIGGER 0x91
+#define RR_ADC_USB_IN_V_STS 0x92
+#define RR_ADC_USB_IN_V_LSB 0x94
+#define RR_ADC_USB_IN_V_MSB 0x95
+#define RR_ADC_USB_IN_I_CTRL 0x98
+#define RR_ADC_USB_IN_I_TRIGGER 0x99
+#define RR_ADC_USB_IN_I_STS 0x9A
+#define RR_ADC_USB_IN_I_LSB 0x9C
+#define RR_ADC_USB_IN_I_MSB 0x9D
+
+#define RR_ADC_DC_IN_V_CTRL 0xA0
+#define RR_ADC_DC_IN_V_TRIGGER 0xA1
+#define RR_ADC_DC_IN_V_STS 0xA2
+#define RR_ADC_DC_IN_V_LSB 0xA4
+#define RR_ADC_DC_IN_V_MSB 0xA5
+#define RR_ADC_DC_IN_I_CTRL 0xA8
+#define RR_ADC_DC_IN_I_TRIGGER 0xA9
+#define RR_ADC_DC_IN_I_STS 0xAA
+#define RR_ADC_DC_IN_I_LSB 0xAC
+#define RR_ADC_DC_IN_I_MSB 0xAD
+
+#define RR_ADC_PMI_DIE_TEMP_CTRL 0xB0
+#define RR_ADC_PMI_DIE_TEMP_TRIGGER 0xB1
+#define RR_ADC_PMI_DIE_TEMP_STS 0xB2
+#define RR_ADC_PMI_DIE_TEMP_CFG 0xB3
+#define RR_ADC_PMI_DIE_TEMP_LSB 0xB4
+#define RR_ADC_PMI_DIE_TEMP_MSB 0xB5
+
+#define RR_ADC_CHARGER_TEMP_CTRL 0xB8
+#define RR_ADC_CHARGER_TEMP_TRIGGER 0xB9
+#define RR_ADC_CHARGER_TEMP_STS 0xBA
+#define RR_ADC_CHARGER_TEMP_CFG 0xBB
+#define RR_ADC_CHARGER_TEMP_LSB 0xBC
+#define RR_ADC_CHARGER_TEMP_MSB 0xBD
+#define RR_ADC_CHARGER_HOT 0xBE
+#define RR_ADC_CHARGER_TOO_HOT 0xBF
+
+#define RR_ADC_GPIO_CTRL 0xC0
+#define RR_ADC_GPIO_TRIGGER 0xC1
+#define RR_ADC_GPIO_STS 0xC2
+#define RR_ADC_GPIO_LSB 0xC4
+#define RR_ADC_GPIO_MSB 0xC5
+
+#define RR_ADC_ATEST_CTRL 0xC8
+#define RR_ADC_ATEST_TRIGGER 0xC9
+#define RR_ADC_ATEST_STS 0xCA
+#define RR_ADC_ATEST_LSB 0xCC
+#define RR_ADC_ATEST_MSB 0xCD
+#define RR_ADC_SEC_ACCESS 0xD0
+
+#define RR_ADC_PERPH_RESET_CTL2 0xD9
+#define RR_ADC_PERPH_RESET_CTL3 0xDA
+#define RR_ADC_PERPH_RESET_CTL4 0xDB
+#define RR_ADC_INT_TEST1 0xE0
+#define RR_ADC_INT_TEST_VAL 0xE1
+
+#define RR_ADC_TM_TRIGGER_CTRLS 0xE2
+#define RR_ADC_TM_ADC_CTRLS 0xE3
+#define RR_ADC_TM_CNL_CTRL 0xE4
+#define RR_ADC_TM_BATT_ID_CTRL 0xE5
+#define RR_ADC_TM_THERM_CTRL 0xE6
+#define RR_ADC_TM_CONV_STS 0xE7
+#define RR_ADC_TM_ADC_READ_LSB 0xE8
+#define RR_ADC_TM_ADC_READ_MSB 0xE9
+#define RR_ADC_TM_ATEST_MUX_1 0xEA
+#define RR_ADC_TM_ATEST_MUX_2 0xEB
+#define RR_ADC_TM_REFERENCES 0xED
+#define RR_ADC_TM_MISC_CTL 0xEE
+#define RR_ADC_TM_RR_CTRL 0xEF
+
+#define RR_ADC_TRIGGER_EVERY_CYCLE BIT(7)
+#define RR_ADC_TRIGGER_CTL BIT(0)
+
+#define RR_ADC_BATT_ID_RANGE 820
+
+#define RR_ADC_BITS 10
+#define RR_ADC_CHAN_MAX_VALUE (1 << RR_ADC_BITS)
+#define RR_ADC_FS_VOLTAGE_MV 2500
+
+/* BATT_THERM 0.25K/LSB */
+#define RR_ADC_BATT_THERM_LSB_K 4
+
+#define RR_ADC_TEMP_FS_VOLTAGE_NUM 5000000
+#define RR_ADC_TEMP_FS_VOLTAGE_DEN 3
+#define RR_ADC_DIE_TEMP_OFFSET 601400
+#define RR_ADC_DIE_TEMP_SLOPE 2
+#define RR_ADC_DIE_TEMP_OFFSET_MILLI_DEGC 25000
+
+#define RR_ADC_CHG_TEMP_GF_OFFSET_UV 1303168
+#define RR_ADC_CHG_TEMP_GF_SLOPE_UV_PER_C 3784
+#define RR_ADC_CHG_TEMP_SMIC_OFFSET_UV 1338433
+#define RR_ADC_CHG_TEMP_SMIC_SLOPE_UV_PER_C 3655
+#define RR_ADC_CHG_TEMP_660_GF_OFFSET_UV 1309001
+#define RR_ADC_CHG_TEMP_660_GF_SLOPE_UV_PER_C 3403
+#define RR_ADC_CHG_TEMP_660_SMIC_OFFSET_UV 1295898
+#define RR_ADC_CHG_TEMP_660_SMIC_SLOPE_UV_PER_C 3596
+#define RR_ADC_CHG_TEMP_660_MGNA_OFFSET_UV 1314779
+#define RR_ADC_CHG_TEMP_660_MGNA_SLOPE_UV_PER_C 3496
+#define RR_ADC_CHG_TEMP_OFFSET_MILLI_DEGC 25000
+#define RR_ADC_CHG_THRESHOLD_SCALE 4
+
+#define RR_ADC_VOLT_INPUT_FACTOR 8
+#define RR_ADC_CURR_INPUT_FACTOR 2000
+#define RR_ADC_CURR_USBIN_INPUT_FACTOR_MIL 1886
+#define RR_ADC_CURR_USBIN_660_FACTOR_MIL 9
+#define RR_ADC_CURR_USBIN_660_UV_VAL 579500
+
+#define RR_ADC_GPIO_FS_RANGE 5000
+#define RR_ADC_COHERENT_CHECK_RETRY 5
+#define RR_ADC_CHAN_MAX_CONTINUOUS_BUFFER_LEN 16
+
+#define RR_ADC_STS_CHANNEL_READING_MASK 0x3
+#define RR_ADC_STS_CHANNEL_STS 0x2
+
+#define RR_ADC_TP_REV_VERSION1 21
+#define RR_ADC_TP_REV_VERSION2 29
+#define RR_ADC_TP_REV_VERSION3 32
+
+#define RRADC_BATT_ID_DELAY_MAX 8
+
+enum rradc_channel_id {
+ RR_ADC_BATT_ID = 0,
+ RR_ADC_BATT_THERM,
+ RR_ADC_SKIN_TEMP,
+ RR_ADC_USBIN_I,
+ RR_ADC_USBIN_V,
+ RR_ADC_DCIN_I,
+ RR_ADC_DCIN_V,
+ RR_ADC_DIE_TEMP,
+ RR_ADC_CHG_TEMP,
+ RR_ADC_GPIO,
+ RR_ADC_CHG_HOT_TEMP,
+ RR_ADC_CHG_TOO_HOT_TEMP,
+ RR_ADC_SKIN_HOT_TEMP,
+ RR_ADC_SKIN_TOO_HOT_TEMP,
+ RR_ADC_CHAN_MAX
+};
+
+struct rradc_chip;
+
+/**
+ * struct rradc_channel - rradc channel data
+ * @lsb: Channel least significant byte
+ * @status: Channel status address
+ * @size: number of bytes to read
+ * @trigger_addr: Trigger address, trigger is only used on some channels
+ * @trigger_mask: Trigger mask
+ * @scale: Channel scale callback
+ */
+struct rradc_channel {
+ u8 lsb;
+ u8 status;
+ int size;
+ int trigger_addr;
+ int trigger_mask;
+ int (*scale)(struct rradc_chip *chip, u16 adc_code, int *result);
+};
+
+struct rradc_chip {
+ struct device *dev;
+ struct qcom_spmi_pmic *pmic;
+ struct mutex lock;
+ struct regmap *regmap;
+ u32 base;
+ int batt_id_delay;
+ u16 batt_id_data;
+};
+
+static const int batt_id_delays[] = { 0, 1, 4, 12, 20, 40, 60, 80 };
+static const struct rradc_channel rradc_chans[RR_ADC_CHAN_MAX];
+static const struct iio_chan_spec rradc_iio_chans[RR_ADC_CHAN_MAX];
+
+static int rradc_read(struct rradc_chip *chip, u16 addr, u8 *data, int len)
+{
+ int ret, retry_cnt = 0;
+ u8 data_check[RR_ADC_CHAN_MAX_CONTINUOUS_BUFFER_LEN];
+
+ if (len > RR_ADC_CHAN_MAX_CONTINUOUS_BUFFER_LEN) {
+ dev_err(chip->dev,
+ "Can't read more than %d bytes, but asked to read %d bytes.\n",
+ RR_ADC_CHAN_MAX_CONTINUOUS_BUFFER_LEN, len);
+ return -EINVAL;
+ }
+
+ while (retry_cnt < RR_ADC_COHERENT_CHECK_RETRY) {
+ ret = regmap_bulk_read(chip->regmap, chip->base + addr, data,
+ len);
+ if (ret < 0) {
+ dev_err(chip->dev, "rr_adc reg 0x%x failed :%d\n", addr,
+ ret);
+ return ret;
+ }
+
+ ret = regmap_bulk_read(chip->regmap, chip->base + addr,
+ data_check, len);
+ if (ret < 0) {
+ dev_err(chip->dev, "rr_adc reg 0x%x failed :%d\n", addr,
+ ret);
+ return ret;
+ }
+
+ if (memcmp(data, data_check, len) != 0) {
+ retry_cnt++;
+ dev_dbg(chip->dev,
+ "coherent read error, retry_cnt:%d\n",
+ retry_cnt);
+ continue;
+ }
+
+ break;
+ }
+
+ if (retry_cnt == RR_ADC_COHERENT_CHECK_RETRY)
+ dev_err(chip->dev, "Retry exceeded for coherrency check\n");
+
+ return ret;
+}
+
+static int rradc_get_fab_coeff(struct rradc_chip *chip, int64_t *offset,
+ int64_t *slope)
+{
+ if (chip->pmic->subtype == PM660_SUBTYPE) {
+ switch (chip->pmic->fab_id) {
+ case PM660_FAB_ID_GF:
+ *offset = RR_ADC_CHG_TEMP_660_GF_OFFSET_UV;
+ *slope = RR_ADC_CHG_TEMP_660_GF_SLOPE_UV_PER_C;
+ break;
+ case PM660_FAB_ID_TSMC:
+ *offset = RR_ADC_CHG_TEMP_660_SMIC_OFFSET_UV;
+ *slope = RR_ADC_CHG_TEMP_660_SMIC_SLOPE_UV_PER_C;
+ break;
+ default:
+ *offset = RR_ADC_CHG_TEMP_660_MGNA_OFFSET_UV;
+ *slope = RR_ADC_CHG_TEMP_660_MGNA_SLOPE_UV_PER_C;
+ }
+ } else if (chip->pmic->subtype == PMI8998_SUBTYPE) {
+ switch (chip->pmic->fab_id) {
+ case PMI8998_FAB_ID_GF:
+ *offset = RR_ADC_CHG_TEMP_GF_OFFSET_UV;
+ *slope = RR_ADC_CHG_TEMP_GF_SLOPE_UV_PER_C;
+ break;
+ case PMI8998_FAB_ID_SMIC:
+ *offset = RR_ADC_CHG_TEMP_SMIC_OFFSET_UV;
+ *slope = RR_ADC_CHG_TEMP_SMIC_SLOPE_UV_PER_C;
+ break;
+ default:
+ return -EINVAL;
+ }
+ } else {
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+/*
+ * These functions explicitly cast int64_t to int.
+ * They will never overflow, as the values are small enough.
+ */
+static int rradc_post_process_batt_id(struct rradc_chip *chip, u16 adc_code,
+ int *result_ohms)
+{
+ uint32_t current_value;
+ int64_t r_id;
+
+ current_value = chip->batt_id_data;
+ r_id = ((int64_t)adc_code * RR_ADC_FS_VOLTAGE_MV);
+ r_id = div64_s64(r_id, (RR_ADC_CHAN_MAX_VALUE * current_value));
+ *result_ohms = (int)(r_id * MILLI);
+
+ return 0;
+}
+
+static int rradc_post_process_therm(struct rradc_chip *chip, u16 adc_code,
+ int *result_millidegc)
+{
+ int64_t temp;
+
+ /* K = code/4 */
+ temp = ((int64_t)adc_code * MILLI);
+ temp = div64_s64(temp, RR_ADC_BATT_THERM_LSB_K);
+ *result_millidegc = (int)milli_kelvin_to_millicelsius(temp);
+
+ return 0;
+}
+
+static int rradc_post_process_volt(struct rradc_chip *chip, u16 adc_code,
+ int *result_uv)
+{
+ int64_t uv;
+
+ /* 8x input attenuation; 2.5V ADC full scale */
+ uv = ((int64_t)adc_code * RR_ADC_VOLT_INPUT_FACTOR);
+ uv *= (RR_ADC_FS_VOLTAGE_MV * MILLI);
+ uv = div64_s64(uv, RR_ADC_CHAN_MAX_VALUE);
+ *result_uv = (int)uv;
+
+ return 0;
+}
+
+static int rradc_post_process_usbin_curr(struct rradc_chip *chip, u16 adc_code,
+ int *result_ua)
+{
+ int64_t ua;
+
+ /* scale * V/A; 2.5V ADC full scale */
+ ua = ((int64_t)adc_code * RR_ADC_CURR_USBIN_INPUT_FACTOR_MIL);
+ ua *= (RR_ADC_FS_VOLTAGE_MV * MILLI);
+ ua = div64_s64(ua, (RR_ADC_CHAN_MAX_VALUE * 10));
+ *result_ua = (int)ua;
+
+ return 0;
+}
+
+static int rradc_post_process_dcin_curr(struct rradc_chip *chip, u16 adc_code,
+ int *result_ua)
+{
+ int64_t ua;
+
+ /* 0.5 V/A; 2.5V ADC full scale */
+ ua = ((int64_t)adc_code * RR_ADC_CURR_INPUT_FACTOR);
+ ua *= (RR_ADC_FS_VOLTAGE_MV * MILLI);
+ ua = div64_s64(ua, (RR_ADC_CHAN_MAX_VALUE * 1000));
+ *result_ua = (int)ua;
+
+ return 0;
+}
+
+static int rradc_post_process_die_temp(struct rradc_chip *chip, u16 adc_code,
+ int *result_millidegc)
+{
+ int64_t temp;
+
+ temp = ((int64_t)adc_code * RR_ADC_TEMP_FS_VOLTAGE_NUM);
+ temp = div64_s64(temp,
+ (RR_ADC_TEMP_FS_VOLTAGE_DEN * RR_ADC_CHAN_MAX_VALUE));
+ temp -= RR_ADC_DIE_TEMP_OFFSET;
+ temp = div64_s64(temp, RR_ADC_DIE_TEMP_SLOPE);
+ temp += RR_ADC_DIE_TEMP_OFFSET_MILLI_DEGC;
+ *result_millidegc = (int)temp;
+
+ return 0;
+}
+
+static int rradc_post_process_chg_temp_hot(struct rradc_chip *chip,
+ u16 adc_code, int *result_millidegc)
+{
+ int64_t uv, offset, slope;
+ int ret;
+
+ ret = rradc_get_fab_coeff(chip, &offset, &slope);
+ if (ret < 0) {
+ dev_err(chip->dev, "Unable to get fab id coefficients\n");
+ return -EINVAL;
+ }
+
+ uv = (int64_t)adc_code * RR_ADC_CHG_THRESHOLD_SCALE;
+ uv = uv * RR_ADC_TEMP_FS_VOLTAGE_NUM;
+ uv = div64_s64(uv,
+ (RR_ADC_TEMP_FS_VOLTAGE_DEN * RR_ADC_CHAN_MAX_VALUE));
+ uv = offset - uv;
+ uv = div64_s64((uv * MILLI), slope);
+ uv = uv + RR_ADC_CHG_TEMP_OFFSET_MILLI_DEGC;
+ *result_millidegc = (int)uv;
+
+ return 0;
+}
+
+static int rradc_post_process_skin_temp_hot(struct rradc_chip *chip,
+ u16 adc_code, int *result_millidegc)
+{
+ int64_t temp;
+
+ temp = (int64_t)adc_code;
+ temp = (div64_s64(temp, 2) - 30) * MILLI;
+ *result_millidegc = (int)temp;
+
+ return 0;
+}
+
+static int rradc_post_process_chg_temp(struct rradc_chip *chip, u16 adc_code,
+ int *result_millidegc)
+{
+ int64_t uv, offset, slope;
+ int ret;
+
+ ret = rradc_get_fab_coeff(chip, &offset, &slope);
+ if (ret < 0) {
+ dev_err(chip->dev, "Unable to get fab id coefficients\n");
+ return -EINVAL;
+ }
+
+ uv = ((int64_t)adc_code * RR_ADC_TEMP_FS_VOLTAGE_NUM);
+ uv = div64_s64(uv,
+ (RR_ADC_TEMP_FS_VOLTAGE_DEN * RR_ADC_CHAN_MAX_VALUE));
+ uv = offset - uv;
+ uv = div64_s64((uv * MILLI), slope);
+ uv += RR_ADC_CHG_TEMP_OFFSET_MILLI_DEGC;
+ *result_millidegc = (int)uv;
+
+ return 0;
+}
+
+static int rradc_post_process_gpio(struct rradc_chip *chip, u16 adc_code,
+ int *result_mv)
+{
+ int64_t mv;
+
+ /* 5V ADC full scale, 10 bit */
+ mv = ((int64_t)adc_code * RR_ADC_GPIO_FS_RANGE);
+ mv = div64_s64(mv, RR_ADC_CHAN_MAX_VALUE);
+ *result_mv = (int)mv;
+
+ return 0;
+}
+
+static int rradc_enable_continuous_mode(struct rradc_chip *chip)
+{
+ int ret;
+
+ /* Clear channel log */
+ ret = regmap_update_bits(chip->regmap, chip->base + RR_ADC_ADC_LOG,
+ RR_ADC_ADC_LOG_CLR_CTRL,
+ RR_ADC_ADC_LOG_CLR_CTRL);
+ if (ret < 0) {
+ dev_err(chip->dev, "log ctrl update to clear failed:%d\n", ret);
+ return ret;
+ }
+
+ ret = regmap_update_bits(chip->regmap, chip->base + RR_ADC_ADC_LOG,
+ RR_ADC_ADC_LOG_CLR_CTRL, 0);
+ if (ret < 0) {
+ dev_err(chip->dev, "log ctrl update to not clear failed:%d\n",
+ ret);
+ return ret;
+ }
+
+ /* Switch to continuous mode */
+ ret = regmap_update_bits(chip->regmap, chip->base + RR_ADC_RR_ADC_CTL,
+ RR_ADC_ADC_CTL_CONTINUOUS_SEL,
+ RR_ADC_ADC_CTL_CONTINUOUS_SEL);
+ if (ret < 0)
+ dev_err(chip->dev, "Update to continuous mode failed:%d\n",
+ ret);
+
+ return ret;
+}
+
+static int rradc_disable_continuous_mode(struct rradc_chip *chip)
+{
+ int ret;
+
+ /* Switch to non continuous mode */
+ ret = regmap_update_bits(chip->regmap, chip->base + RR_ADC_RR_ADC_CTL,
+ RR_ADC_ADC_CTL_CONTINUOUS_SEL, 0);
+ if (ret < 0)
+ dev_err(chip->dev, "Update to non-continuous mode failed:%d\n",
+ ret);
+
+ return ret;
+}
+
+static bool rradc_is_ready(struct rradc_chip *chip,
+ enum rradc_channel_id chan_id)
+{
+ const struct rradc_channel *chan = &rradc_chans[chan_id];
+ int ret;
+ unsigned int status, mask;
+
+ /* BATT_ID STS bit does not get set initially */
+ switch (chan_id) {
+ case RR_ADC_BATT_ID:
+ mask = RR_ADC_STS_CHANNEL_STS;
+ break;
+ default:
+ mask = RR_ADC_STS_CHANNEL_READING_MASK;
+ break;
+ }
+
+ ret = regmap_read(chip->regmap, chip->base + chan->status, &status);
+ if (ret < 0 || !(status & mask))
+ return false;
+
+ return true;
+}
+
+static int rradc_read_status_in_cont_mode(struct rradc_chip *chip,
+ enum rradc_channel_id chan_id)
+{
+ const struct rradc_channel *chan = &rradc_chans[chan_id];
+ const struct iio_chan_spec *iio_chan = &rradc_iio_chans[chan_id];
+ int ret;
+
+ if (chan->trigger_mask == 0) {
+ dev_err(chip->dev, "Channel doesn't have a trigger mask\n");
+ return -EINVAL;
+ }
+
+ ret = regmap_update_bits(chip->regmap, chip->base + chan->trigger_addr,
+ chan->trigger_mask, chan->trigger_mask);
+ if (ret < 0) {
+ dev_err(chip->dev,
+ "Failed to apply trigger for channel '%s' ret=%d\n",
+ iio_chan->datasheet_name, ret);
+ return ret;
+ }
+
+ ret = rradc_enable_continuous_mode(chip);
+ if (ret < 0) {
+ dev_err(chip->dev, "Failed to switch to continuous mode\n");
+ goto disable_trigger;
+ }
+
+ if (!rradc_is_ready(chip, chan_id))
+ dev_err(chip->dev, "channel '%s' is not ready\n",
+ iio_chan->datasheet_name);
+
+ ret = rradc_disable_continuous_mode(chip);
+ if (ret < 0)
+ dev_err(chip->dev, "Failed to switch to non continuous mode\n");
+
+disable_trigger:
+ ret = regmap_update_bits(chip->regmap, chip->base + chan->trigger_addr,
+ chan->trigger_mask, 0);
+ if (ret < 0)
+ dev_err(chip->dev,
+ "Failed to apply trigger for channel '%s' ret=%d\n",
+ iio_chan->datasheet_name, ret);
+
+ return ret;
+}
+
+static int rradc_prepare_batt_id_conversion(struct rradc_chip *chip,
+ enum rradc_channel_id chan_id,
+ u16 *data)
+{
+ int ret, batt_id_delay;
+
+ ret = regmap_update_bits(chip->regmap, chip->base + RR_ADC_BATT_ID_CTRL,
+ RR_ADC_BATT_ID_CTRL_CHANNEL_CONV,
+ RR_ADC_BATT_ID_CTRL_CHANNEL_CONV);
+ if (ret < 0) {
+ dev_err(chip->dev, "Enabling BATT ID channel failed:%d\n", ret);
+ return ret;
+ }
+
+ if (chip->batt_id_delay != -EINVAL) {
+ batt_id_delay =
+ FIELD_PREP(BATT_ID_SETTLE_MASK, chip->batt_id_delay);
+ ret = regmap_update_bits(chip->regmap,
+ chip->base + RR_ADC_BATT_ID_CFG,
+ batt_id_delay, batt_id_delay);
+ if (ret < 0) {
+ dev_err(chip->dev,
+ "BATT_ID settling time config failed:%d\n",
+ ret);
+ goto out_disable_batt_id;
+ }
+ }
+
+ ret = regmap_update_bits(chip->regmap,
+ chip->base + RR_ADC_BATT_ID_TRIGGER,
+ RR_ADC_TRIGGER_CTL, RR_ADC_TRIGGER_CTL);
+ if (ret < 0) {
+ dev_err(chip->dev, "BATT_ID trigger set failed:%d\n", ret);
+ goto out_disable_batt_id;
+ }
+
+ ret = rradc_read_status_in_cont_mode(chip, chan_id);
+ if (ret < 0)
+ dev_err(chip->dev, "Error reading in continuous mode:%d\n",
+ ret);
+
+ /*
+ * Reset registers back to default values
+ */
+ ret = regmap_update_bits(chip->regmap,
+ chip->base + RR_ADC_BATT_ID_TRIGGER,
+ RR_ADC_TRIGGER_CTL, 0);
+ if (ret < 0)
+ dev_err(chip->dev, "BATT_ID trigger re-set failed:%d\n", ret);
+
+out_disable_batt_id:
+ ret = regmap_update_bits(chip->regmap, chip->base + RR_ADC_BATT_ID_CTRL,
+ RR_ADC_BATT_ID_CTRL_CHANNEL_CONV, 0);
+ if (ret < 0)
+ dev_err(chip->dev, "Disabling BATT ID channel failed:%d\n",
+ ret);
+
+ return ret;
+}
+
+static int rradc_do_conversion(struct rradc_chip *chip,
+ enum rradc_channel_id chan_id, u16 *data)
+{
+ const struct rradc_channel *chan = &rradc_chans[chan_id];
+ const struct iio_chan_spec *iio_chan = &rradc_iio_chans[chan_id];
+ int ret;
+ u8 buf[6];
+
+ mutex_lock(&chip->lock);
+
+ switch (chan_id) {
+ case RR_ADC_BATT_ID:
+ ret = rradc_prepare_batt_id_conversion(chip, chan_id, data);
+ if (ret < 0) {
+ dev_err(chip->dev, "Battery ID conversion failed:%d\n",
+ ret);
+ goto unlock_out;
+ }
+ break;
+
+ case RR_ADC_USBIN_V:
+ case RR_ADC_DIE_TEMP:
+ ret = rradc_read_status_in_cont_mode(chip, chan_id);
+ if (ret < 0) {
+ dev_err(chip->dev,
+ "Error reading in continuous mode:%d\n", ret);
+ goto unlock_out;
+ }
+ break;
+ case RR_ADC_CHG_HOT_TEMP:
+ case RR_ADC_CHG_TOO_HOT_TEMP:
+ case RR_ADC_SKIN_HOT_TEMP:
+ case RR_ADC_SKIN_TOO_HOT_TEMP:
+ break;
+ default:
+ if (!rradc_is_ready(chip, chan_id)) {
+ /*
+ * Usually this means the channel isn't attached, for example
+ * the in_voltage_usbin_v_input channel will not be ready if
+ * no USB cable is attached
+ */
+ dev_dbg(chip->dev, "channel '%s' is not ready\n",
+ iio_chan->datasheet_name);
+ ret = -ENODATA;
+ goto unlock_out;
+ }
+ break;
+ }
+
+ ret = rradc_read(chip, chan->lsb, buf, chan->size);
+ if (ret) {
+ dev_err(chip->dev, "read data failed\n");
+ goto unlock_out;
+ }
+
+ /*
+ * For the battery ID we read the register for every ID ADC and then
+ * see which one is actually connected.
+ */
+ if (chan_id == RR_ADC_BATT_ID) {
+ u16 batt_id_150 = get_unaligned_le16(buf + 4);
+ u16 batt_id_15 = get_unaligned_le16(buf + 2);
+ u16 batt_id_5 = get_unaligned_le16(buf);
+
+ if (!batt_id_150 && !batt_id_15 && !batt_id_5) {
+ dev_err(chip->dev,
+ "Invalid batt_id values with all zeros\n");
+ ret = -EINVAL;
+ goto unlock_out;
+ }
+
+ if (batt_id_150 <= RR_ADC_BATT_ID_RANGE) {
+ *data = batt_id_150;
+ chip->batt_id_data = 150;
+ } else if (batt_id_15 <= RR_ADC_BATT_ID_RANGE) {
+ *data = batt_id_15;
+ chip->batt_id_data = 15;
+ } else {
+ *data = batt_id_5;
+ chip->batt_id_data = 5;
+ }
+ } else {
+ /*
+ * All of the other channels are either 1 or 2 bytes.
+ * We can rely on the second byte being 0 for 1-byte channels.
+ */
+ *data = get_unaligned_le16(buf);
+ }
+
+unlock_out:
+ mutex_unlock(&chip->lock);
+
+ return ret;
+}
+
+static int rradc_read_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan_spec, int *val,
+ int *val2, long mask)
+{
+ struct rradc_chip *chip = iio_priv(indio_dev);
+ const struct rradc_channel *chan;
+ int ret;
+ u16 adc_code;
+
+ if (chan_spec->address >= RR_ADC_CHAN_MAX) {
+ dev_err(chip->dev, "Invalid channel index:%ld\n",
+ chan_spec->address);
+ return -EINVAL;
+ }
+
+ chan = &rradc_chans[chan_spec->address];
+ ret = rradc_do_conversion(chip, chan_spec->address, &adc_code);
+ if (ret < 0)
+ return ret;
+
+ switch (mask) {
+ case IIO_CHAN_INFO_RAW:
+ *val = adc_code;
+ return IIO_VAL_INT;
+ case IIO_CHAN_INFO_PROCESSED:
+ chan->scale(chip, adc_code, val);
+ return IIO_VAL_INT;
+ default:
+ return -EINVAL;
+ }
+}
+
+static const struct iio_info rradc_info = {
+ .read_raw = &rradc_read_raw,
+};
+
+static const struct rradc_channel rradc_chans[RR_ADC_CHAN_MAX] = {
+ {
+ .scale = rradc_post_process_batt_id,
+ .lsb = RR_ADC_BATT_ID_5_LSB,
+ .status = RR_ADC_BATT_ID_STS,
+ .size = 6,
+ .trigger_addr = RR_ADC_BATT_ID_TRIGGER,
+ .trigger_mask = BIT(0),
+ },
+ {
+ .scale = rradc_post_process_therm,
+ .lsb = RR_ADC_BATT_THERM_LSB,
+ .status = RR_ADC_BATT_THERM_STS,
+ .size = 2,
+ .trigger_addr = RR_ADC_BATT_THERM_TRIGGER,
+ },
+ {
+ .scale = rradc_post_process_therm,
+ .lsb = RR_ADC_SKIN_TEMP_LSB,
+ .status = RR_ADC_AUX_THERM_STS,
+ .size = 2,
+ .trigger_addr = RR_ADC_AUX_THERM_TRIGGER,
+ },
+ {
+ .scale = rradc_post_process_usbin_curr,
+ .lsb = RR_ADC_USB_IN_I_LSB,
+ .status = RR_ADC_USB_IN_I_STS,
+ .size = 2,
+ .trigger_addr = RR_ADC_USB_IN_I_TRIGGER,
+ },
+ {
+ .scale = rradc_post_process_volt,
+ .lsb = RR_ADC_USB_IN_V_LSB,
+ .status = RR_ADC_USB_IN_V_STS,
+ .size = 2,
+ .trigger_addr = RR_ADC_USB_IN_V_TRIGGER,
+ .trigger_mask = BIT(7),
+ },
+ {
+ .scale = rradc_post_process_dcin_curr,
+ .lsb = RR_ADC_DC_IN_I_LSB,
+ .status = RR_ADC_DC_IN_I_STS,
+ .size = 2,
+ .trigger_addr = RR_ADC_DC_IN_I_TRIGGER,
+ },
+ {
+ .scale = rradc_post_process_volt,
+ .lsb = RR_ADC_DC_IN_V_LSB,
+ .status = RR_ADC_DC_IN_V_STS,
+ .size = 2,
+ .trigger_addr = RR_ADC_DC_IN_V_TRIGGER,
+ },
+ {
+ .scale = rradc_post_process_die_temp,
+ .lsb = RR_ADC_PMI_DIE_TEMP_LSB,
+ .status = RR_ADC_PMI_DIE_TEMP_STS,
+ .size = 2,
+ .trigger_addr = RR_ADC_PMI_DIE_TEMP_TRIGGER,
+ .trigger_mask = RR_ADC_TRIGGER_EVERY_CYCLE,
+ },
+ {
+ .scale = rradc_post_process_chg_temp,
+ .lsb = RR_ADC_CHARGER_TEMP_LSB,
+ .status = RR_ADC_CHARGER_TEMP_STS,
+ .size = 2,
+ .trigger_addr = RR_ADC_CHARGER_TEMP_TRIGGER,
+ },
+ {
+ .scale = rradc_post_process_gpio,
+ .lsb = RR_ADC_GPIO_LSB,
+ .status = RR_ADC_GPIO_STS,
+ .size = 2,
+ .trigger_addr = RR_ADC_GPIO_TRIGGER,
+ },
+ {
+ .scale = rradc_post_process_chg_temp_hot,
+ .lsb = RR_ADC_CHARGER_HOT,
+ .status = RR_ADC_CHARGER_TEMP_STS,
+ .size = 1,
+ .trigger_addr = RR_ADC_CHARGER_TEMP_TRIGGER,
+ },
+ {
+ .scale = rradc_post_process_chg_temp_hot,
+ .lsb = RR_ADC_CHARGER_TOO_HOT,
+ .status = RR_ADC_CHARGER_TEMP_STS,
+ .size = 1,
+ .trigger_addr = RR_ADC_CHARGER_TEMP_TRIGGER,
+ },
+ {
+ .scale = rradc_post_process_skin_temp_hot,
+ .lsb = RR_ADC_SKIN_HOT,
+ .status = RR_ADC_AUX_THERM_STS,
+ .size = 1,
+ .trigger_addr = RR_ADC_AUX_THERM_TRIGGER,
+ },
+ {
+ .scale = rradc_post_process_skin_temp_hot,
+ .lsb = RR_ADC_SKIN_TOO_HOT,
+ .status = RR_ADC_AUX_THERM_STS,
+ .size = 1,
+ .trigger_addr = RR_ADC_AUX_THERM_TRIGGER,
+ },
+};
+
+static const struct iio_chan_spec rradc_iio_chans[RR_ADC_CHAN_MAX] = {
+ {
+ .datasheet_name = "batt_id",
+ .type = IIO_RESISTANCE,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+ .address = RR_ADC_BATT_ID,
+ },
+ {
+ .datasheet_name = "batt_therm",
+ .type = IIO_TEMP,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+ .address = RR_ADC_BATT_THERM,
+ },
+ {
+ .datasheet_name = "skin_temp",
+ .type = IIO_TEMP,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED)|
+ BIT(IIO_CHAN_INFO_RAW),
+ .address = RR_ADC_SKIN_TEMP,
+ },
+ {
+ .datasheet_name = "usbin_i",
+ .type = IIO_CURRENT,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+ .address = RR_ADC_USBIN_I,
+ },
+ {
+ .datasheet_name = "usbin_v",
+ .type = IIO_VOLTAGE,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+ .address = RR_ADC_USBIN_V,
+ },
+ {
+ .datasheet_name = "dcin_i",
+ .type = IIO_CURRENT,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+ .address = RR_ADC_DCIN_I,
+ },
+ {
+ .datasheet_name = "dcin_v",
+ .type = IIO_VOLTAGE,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+ .address = RR_ADC_DCIN_V,
+ },
+ {
+ .datasheet_name = "die_temp",
+ .type = IIO_TEMP,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED)|
+ BIT(IIO_CHAN_INFO_RAW),
+ .address = RR_ADC_DIE_TEMP,
+ },
+ {
+ .datasheet_name = "chg_temp",
+ .type = IIO_TEMP,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED)|
+ BIT(IIO_CHAN_INFO_RAW),
+ .address = RR_ADC_CHG_TEMP,
+ },
+ {
+ .datasheet_name = "gpio",
+ .type = IIO_VOLTAGE,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED)|
+ BIT(IIO_CHAN_INFO_RAW),
+ .address = RR_ADC_GPIO,
+ },
+ {
+ .datasheet_name = "chg_temp_hot",
+ .type = IIO_TEMP,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED)|
+ BIT(IIO_CHAN_INFO_RAW),
+ .address = RR_ADC_CHG_HOT_TEMP,
+ },
+ {
+ .datasheet_name = "chg_temp_too_hot",
+ .type = IIO_TEMP,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED)|
+ BIT(IIO_CHAN_INFO_RAW),
+ .address = RR_ADC_CHG_TOO_HOT_TEMP,
+ },
+ {
+ .datasheet_name = "skin_temp_hot",
+ .type = IIO_TEMP,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED)|
+ BIT(IIO_CHAN_INFO_RAW),
+ .address = RR_ADC_SKIN_TEMP,
+ },
+ {
+ .datasheet_name = "skin_temp_too_hot",
+ .type = IIO_TEMP,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED)|
+ BIT(IIO_CHAN_INFO_RAW),
+ .address = RR_ADC_SKIN_TEMP,
+ },
+};
+
+static int rradc_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct iio_dev *indio_dev;
+ struct rradc_chip *chip;
+ int ret, i;
+
+ indio_dev = devm_iio_device_alloc(dev, sizeof(*chip));
+ if (!indio_dev)
+ return -ENOMEM;
+
+ chip = iio_priv(indio_dev);
+ chip->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+ if (!chip->regmap) {
+ dev_err(dev, "Couldn't get parent's regmap\n");
+ return -EINVAL;
+ }
+
+ chip->dev = dev;
+ mutex_init(&chip->lock);
+
+ ret = device_property_read_u32(dev, "reg", &chip->base);
+ if (ret < 0) {
+ dev_err(chip->dev, "Couldn't find reg address, ret = %d\n",
+ ret);
+ return ret;
+ }
+
+ chip->batt_id_delay = -EINVAL;
+ ret = device_property_read_u32(dev, "qcom,batt-id-delay-ms",
+ &chip->batt_id_delay);
+ if (!ret) {
+ for (i = 0; i < RRADC_BATT_ID_DELAY_MAX; i++) {
+ if (chip->batt_id_delay == batt_id_delays[i])
+ break;
+ }
+ if (i == RRADC_BATT_ID_DELAY_MAX)
+ chip->batt_id_delay = -EINVAL;
+ }
+
+ /* Get the PMIC revision ID, we need to handle some varying coefficients */
+ chip->pmic = (struct qcom_spmi_pmic *)spmi_device_get_drvdata(
+ to_spmi_device(pdev->dev.parent));
+ qcom_pmic_print_info(chip->dev, chip->pmic);
+
+ indio_dev->name = pdev->name;
+ indio_dev->modes = INDIO_DIRECT_MODE;
+ indio_dev->info = &rradc_info;
+ indio_dev->channels = rradc_iio_chans;
+ indio_dev->num_channels = RR_ADC_CHAN_MAX;
+
+ return devm_iio_device_register(dev, indio_dev);
+}
+
+static const struct of_device_id rradc_match_table[] = {
+ { .compatible = "qcom,pm660-rradc" },
+ { .compatible = "qcom,pmi8998-rradc" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, rradc_match_table);
+
+static struct platform_driver rradc_driver = {
+ .driver = {
+ .name = "qcom-rradc",
+ .of_match_table = rradc_match_table,
+ },
+ .probe = rradc_probe,
+};
+module_platform_driver(rradc_driver);
+
+MODULE_DESCRIPTION("QCOM SPMI PMIC RR ADC driver");
+MODULE_AUTHOR("Caleb Connolly <caleb.connolly@linaro.org>");
+MODULE_LICENSE("GPL v2");
--
2.34.1
^ permalink raw reply related [flat|nested] 10+ messages in thread