[PATCH v3 06/10] serial: 8250: dma: Allow driver operations before starting DMA transfers

[Miquel Raynal <miquel.raynal@bootlin.com>]

One situation where this could be used is when configuring the UART
controller to be the DMA flow controller. This is a typical case where
the driver might need to program a few more registers before starting a
DMA transfer. Provide the necessary infrastructure to support this
case.

Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 drivers/tty/serial/8250/8250.h     | 18 ++++++++++++++++++
 drivers/tty/serial/8250/8250_dma.c |  4 ++++
 2 files changed, 22 insertions(+)

diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h
index db784ace25d8..d19f24e4d13e 100644
--- a/drivers/tty/serial/8250/8250.h
+++ b/drivers/tty/serial/8250/8250.h
@@ -17,6 +17,8 @@
 struct uart_8250_dma {
 	int (*tx_dma)(struct uart_8250_port *p);
 	int (*rx_dma)(struct uart_8250_port *p);
+	void (*prepare_tx_dma)(struct uart_8250_port *p);
+	void (*prepare_rx_dma)(struct uart_8250_port *p);
 
 	/* Filter function */
 	dma_filter_fn		fn;
@@ -301,6 +303,22 @@ extern int serial8250_rx_dma(struct uart_8250_port *);
 extern void serial8250_rx_dma_flush(struct uart_8250_port *);
 extern int serial8250_request_dma(struct uart_8250_port *);
 extern void serial8250_release_dma(struct uart_8250_port *);
+
+static inline void serial8250_do_prepare_tx_dma(struct uart_8250_port *p)
+{
+	struct uart_8250_dma *dma = p->dma;
+
+	if (dma->prepare_tx_dma)
+		dma->prepare_tx_dma(p);
+}
+
+static inline void serial8250_do_prepare_rx_dma(struct uart_8250_port *p)
+{
+	struct uart_8250_dma *dma = p->dma;
+
+	if (dma->prepare_rx_dma)
+		dma->prepare_rx_dma(p);
+}
 #else
 static inline int serial8250_tx_dma(struct uart_8250_port *p)
 {
diff --git a/drivers/tty/serial/8250/8250_dma.c b/drivers/tty/serial/8250/8250_dma.c
index 890fa7ddaa7f..558d3a2ac65b 100644
--- a/drivers/tty/serial/8250/8250_dma.c
+++ b/drivers/tty/serial/8250/8250_dma.c
@@ -77,6 +77,8 @@ int serial8250_tx_dma(struct uart_8250_port *p)
 
 	dma->tx_size = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
 
+	serial8250_do_prepare_tx_dma(p);
+
 	desc = dmaengine_prep_slave_single(dma->txchan,
 					   dma->tx_addr + xmit->tail,
 					   dma->tx_size, DMA_MEM_TO_DEV,
@@ -114,6 +116,8 @@ int serial8250_rx_dma(struct uart_8250_port *p)
 	if (dma->rx_running)
 		return 0;
 
+	serial8250_do_prepare_rx_dma(p);
+
 	desc = dmaengine_prep_slave_single(dma->rxchan, dma->rx_addr,
 					   dma->rx_size, DMA_DEV_TO_MEM,
 					   DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
-- 
2.27.0