* [PATCH v4 1/9] arm64: dts: qcom: align dmas in I2C/SPI/UART with DT schema
2022-04-05 6:34 [PATCH v4 0/9] dt-bindings: qcom: convert entire GSBI (QUP I2C/SPI/UART) to DT schema Krzysztof Kozlowski
@ 2022-04-05 6:34 ` Krzysztof Kozlowski
2022-04-05 6:34 ` [PATCH v4 2/9] arm64: dts: qcom: align clocks in I2C/SPI " Krzysztof Kozlowski
` (8 subsequent siblings)
9 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-05 6:34 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Greg Kroah-Hartman, Mark Brown, linux-arm-msm, linux-i2c,
devicetree, linux-kernel, linux-serial, linux-spi
Cc: Kuldeep Singh, Krzysztof Kozlowski
The DT schema expects dma channels in tx-rx order. No functional
change.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
Dropped Kuldeep's ack because of changes - more properties changed.
---
arch/arm64/boot/dts/qcom/ipq6018.dtsi | 8 +++----
arch/arm64/boot/dts/qcom/ipq8074.dtsi | 16 +++++++-------
arch/arm64/boot/dts/qcom/msm8916.dtsi | 32 +++++++++++++--------------
arch/arm64/boot/dts/qcom/qcs404.dtsi | 20 ++++++++---------
4 files changed, 38 insertions(+), 38 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
index aac56575e30d..87c28ffa44d3 100644
--- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
@@ -322,8 +322,8 @@ i2c_0: i2c@78b6000 {
<&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
clock-names = "iface", "core";
clock-frequency = <400000>;
- dmas = <&blsp_dma 15>, <&blsp_dma 14>;
- dma-names = "rx", "tx";
+ dmas = <&blsp_dma 14>, <&blsp_dma 15>;
+ dma-names = "tx", "rx";
status = "disabled";
};
@@ -337,8 +337,8 @@ i2c_1: i2c@78b7000 { /* BLSP1 QUP2 */
<&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
clock-names = "iface", "core";
clock-frequency = <400000>;
- dmas = <&blsp_dma 17>, <&blsp_dma 16>;
- dma-names = "rx", "tx";
+ dmas = <&blsp_dma 16>, <&blsp_dma 17>;
+ dma-names = "tx", "rx";
status = "disabled";
};
diff --git a/arch/arm64/boot/dts/qcom/ipq8074.dtsi b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
index d80b1cefab10..2072638006a4 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
@@ -471,8 +471,8 @@ blsp1_i2c2: i2c@78b6000 {
<&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
clock-names = "iface", "core";
clock-frequency = <400000>;
- dmas = <&blsp_dma 15>, <&blsp_dma 14>;
- dma-names = "rx", "tx";
+ dmas = <&blsp_dma 14>, <&blsp_dma 15>;
+ dma-names = "tx", "rx";
pinctrl-0 = <&i2c_0_pins>;
pinctrl-names = "default";
status = "disabled";
@@ -488,8 +488,8 @@ blsp1_i2c3: i2c@78b7000 {
<&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
clock-names = "iface", "core";
clock-frequency = <100000>;
- dmas = <&blsp_dma 17>, <&blsp_dma 16>;
- dma-names = "rx", "tx";
+ dmas = <&blsp_dma 16>, <&blsp_dma 17>;
+ dma-names = "tx", "rx";
status = "disabled";
};
@@ -503,8 +503,8 @@ blsp1_i2c5: i2c@78b9000 {
<&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>;
clock-names = "iface", "core";
clock-frequency = <400000>;
- dmas = <&blsp_dma 21>, <&blsp_dma 20>;
- dma-names = "rx", "tx";
+ dmas = <&blsp_dma 20>, <&blsp_dma 21>;
+ dma-names = "tx", "rx";
status = "disabled";
};
@@ -518,8 +518,8 @@ blsp1_i2c6: i2c@78ba000 {
<&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>;
clock-names = "iface", "core";
clock-frequency = <100000>;
- dmas = <&blsp_dma 23>, <&blsp_dma 22>;
- dma-names = "rx", "tx";
+ dmas = <&blsp_dma 22>, <&blsp_dma 23>;
+ dma-names = "tx", "rx";
status = "disabled";
};
diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index e34963505e07..384fc8738130 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -1485,8 +1485,8 @@ blsp1_uart1: serial@78af000 {
interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
- dmas = <&blsp_dma 1>, <&blsp_dma 0>;
- dma-names = "rx", "tx";
+ dmas = <&blsp_dma 0>, <&blsp_dma 1>;
+ dma-names = "tx", "rx";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp1_uart1_default>;
pinctrl-1 = <&blsp1_uart1_sleep>;
@@ -1499,8 +1499,8 @@ blsp1_uart2: serial@78b0000 {
interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
- dmas = <&blsp_dma 3>, <&blsp_dma 2>;
- dma-names = "rx", "tx";
+ dmas = <&blsp_dma 2>, <&blsp_dma 3>;
+ dma-names = "tx", "rx";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp1_uart2_default>;
pinctrl-1 = <&blsp1_uart2_sleep>;
@@ -1529,8 +1529,8 @@ blsp_spi1: spi@78b5000 {
clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
- dmas = <&blsp_dma 5>, <&blsp_dma 4>;
- dma-names = "rx", "tx";
+ dmas = <&blsp_dma 4>, <&blsp_dma 5>;
+ dma-names = "tx", "rx";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&spi1_default>;
pinctrl-1 = <&spi1_sleep>;
@@ -1561,8 +1561,8 @@ blsp_spi2: spi@78b6000 {
clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
- dmas = <&blsp_dma 7>, <&blsp_dma 6>;
- dma-names = "rx", "tx";
+ dmas = <&blsp_dma 6>, <&blsp_dma 7>;
+ dma-names = "tx", "rx";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&spi2_default>;
pinctrl-1 = <&spi2_sleep>;
@@ -1593,8 +1593,8 @@ blsp_spi3: spi@78b7000 {
clocks = <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
- dmas = <&blsp_dma 9>, <&blsp_dma 8>;
- dma-names = "rx", "tx";
+ dmas = <&blsp_dma 8>, <&blsp_dma 9>;
+ dma-names = "tx", "rx";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&spi3_default>;
pinctrl-1 = <&spi3_sleep>;
@@ -1625,8 +1625,8 @@ blsp_spi4: spi@78b8000 {
clocks = <&gcc GCC_BLSP1_QUP4_SPI_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
- dmas = <&blsp_dma 11>, <&blsp_dma 10>;
- dma-names = "rx", "tx";
+ dmas = <&blsp_dma 10>, <&blsp_dma 11>;
+ dma-names = "tx", "rx";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&spi4_default>;
pinctrl-1 = <&spi4_sleep>;
@@ -1657,8 +1657,8 @@ blsp_spi5: spi@78b9000 {
clocks = <&gcc GCC_BLSP1_QUP5_SPI_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
- dmas = <&blsp_dma 13>, <&blsp_dma 12>;
- dma-names = "rx", "tx";
+ dmas = <&blsp_dma 12>, <&blsp_dma 13>;
+ dma-names = "tx", "rx";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&spi5_default>;
pinctrl-1 = <&spi5_sleep>;
@@ -1689,8 +1689,8 @@ blsp_spi6: spi@78ba000 {
clocks = <&gcc GCC_BLSP1_QUP6_SPI_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
- dmas = <&blsp_dma 15>, <&blsp_dma 14>;
- dma-names = "rx", "tx";
+ dmas = <&blsp_dma 14>, <&blsp_dma 15>;
+ dma-names = "tx", "rx";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&spi6_default>;
pinctrl-1 = <&spi6_sleep>;
diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
index 3f06f7cd3cf2..6b3a8e1006d0 100644
--- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
@@ -823,8 +823,8 @@ blsp1_uart0: serial@78af000 {
interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_BLSP1_UART0_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
- dmas = <&blsp1_dma 1>, <&blsp1_dma 0>;
- dma-names = "rx", "tx";
+ dmas = <&blsp1_dma 0>, <&blsp1_dma 1>;
+ dma-names = "tx", "rx";
pinctrl-names = "default";
pinctrl-0 = <&blsp1_uart0_default>;
status = "disabled";
@@ -836,8 +836,8 @@ blsp1_uart1: serial@78b0000 {
interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
- dmas = <&blsp1_dma 3>, <&blsp1_dma 2>;
- dma-names = "rx", "tx";
+ dmas = <&blsp1_dma 2>, <&blsp1_dma 3>;
+ dma-names = "tx", "rx";
pinctrl-names = "default";
pinctrl-0 = <&blsp1_uart1_default>;
status = "disabled";
@@ -849,8 +849,8 @@ blsp1_uart2: serial@78b1000 {
interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
- dmas = <&blsp1_dma 5>, <&blsp1_dma 4>;
- dma-names = "rx", "tx";
+ dmas = <&blsp1_dma 4>, <&blsp1_dma 5>;
+ dma-names = "tx", "rx";
pinctrl-names = "default";
pinctrl-0 = <&blsp1_uart2_default>;
status = "okay";
@@ -903,8 +903,8 @@ blsp1_uart3: serial@78b2000 {
interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
- dmas = <&blsp1_dma 7>, <&blsp1_dma 6>;
- dma-names = "rx", "tx";
+ dmas = <&blsp1_dma 6>, <&blsp1_dma 7>;
+ dma-names = "tx", "rx";
pinctrl-names = "default";
pinctrl-0 = <&blsp1_uart3_default>;
status = "disabled";
@@ -1067,8 +1067,8 @@ blsp2_uart0: serial@7aef000 {
interrupts = <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_BLSP2_UART0_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
clock-names = "core", "iface";
- dmas = <&blsp2_dma 1>, <&blsp2_dma 0>;
- dma-names = "rx", "tx";
+ dmas = <&blsp2_dma 0>, <&blsp2_dma 1>;
+ dma-names = "tx", "rx";
pinctrl-names = "default";
pinctrl-0 = <&blsp2_uart0_default>;
status = "disabled";
--
2.32.0
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v4 2/9] arm64: dts: qcom: align clocks in I2C/SPI with DT schema
2022-04-05 6:34 [PATCH v4 0/9] dt-bindings: qcom: convert entire GSBI (QUP I2C/SPI/UART) to DT schema Krzysztof Kozlowski
2022-04-05 6:34 ` [PATCH v4 1/9] arm64: dts: qcom: align dmas in I2C/SPI/UART with " Krzysztof Kozlowski
@ 2022-04-05 6:34 ` Krzysztof Kozlowski
2022-04-05 6:34 ` [PATCH v4 3/9] ARM: dts: qcom: ipq4019: align dmas in SPI/UART " Krzysztof Kozlowski
` (7 subsequent siblings)
9 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-05 6:34 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Greg Kroah-Hartman, Mark Brown, linux-arm-msm, linux-i2c,
devicetree, linux-kernel, linux-serial, linux-spi
Cc: Kuldeep Singh, Krzysztof Kozlowski
The DT schema expects clocks core-iface order. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
Dropped Kuldeep's ack because of changes - more properties changed.
---
arch/arm64/boot/dts/qcom/ipq6018.dtsi | 12 ++---
arch/arm64/boot/dts/qcom/ipq8074.dtsi | 24 ++++-----
arch/arm64/boot/dts/qcom/msm8916.dtsi | 36 +++++++-------
arch/arm64/boot/dts/qcom/msm8953.dtsi | 48 +++++++++---------
arch/arm64/boot/dts/qcom/msm8994.dtsi | 42 ++++++++--------
arch/arm64/boot/dts/qcom/msm8996.dtsi | 36 +++++++-------
arch/arm64/boot/dts/qcom/qcs404.dtsi | 72 +++++++++++++--------------
7 files changed, 135 insertions(+), 135 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
index 87c28ffa44d3..8032d7933c66 100644
--- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
@@ -318,9 +318,9 @@ i2c_0: i2c@78b6000 {
#size-cells = <0>;
reg = <0x0 0x078b6000 0x0 0x600>;
interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
clock-frequency = <400000>;
dmas = <&blsp_dma 14>, <&blsp_dma 15>;
dma-names = "tx", "rx";
@@ -333,9 +333,9 @@ i2c_1: i2c@78b7000 { /* BLSP1 QUP2 */
#size-cells = <0>;
reg = <0x0 0x078b7000 0x0 0x600>;
interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
clock-frequency = <400000>;
dmas = <&blsp_dma 16>, <&blsp_dma 17>;
dma-names = "tx", "rx";
diff --git a/arch/arm64/boot/dts/qcom/ipq8074.dtsi b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
index 2072638006a4..8e41c910b8f9 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
@@ -467,9 +467,9 @@ blsp1_i2c2: i2c@78b6000 {
#size-cells = <0>;
reg = <0x078b6000 0x600>;
interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
clock-frequency = <400000>;
dmas = <&blsp_dma 14>, <&blsp_dma 15>;
dma-names = "tx", "rx";
@@ -484,9 +484,9 @@ blsp1_i2c3: i2c@78b7000 {
#size-cells = <0>;
reg = <0x078b7000 0x600>;
interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
clock-frequency = <100000>;
dmas = <&blsp_dma 16>, <&blsp_dma 17>;
dma-names = "tx", "rx";
@@ -499,9 +499,9 @@ blsp1_i2c5: i2c@78b9000 {
#size-cells = <0>;
reg = <0x78b9000 0x600>;
interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
clock-frequency = <400000>;
dmas = <&blsp_dma 20>, <&blsp_dma 21>;
dma-names = "tx", "rx";
@@ -514,9 +514,9 @@ blsp1_i2c6: i2c@78ba000 {
#size-cells = <0>;
reg = <0x078ba000 0x600>;
interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
clock-frequency = <100000>;
dmas = <&blsp_dma 22>, <&blsp_dma 23>;
dma-names = "tx", "rx";
diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index 384fc8738130..15d9731469ca 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -1511,9 +1511,9 @@ blsp_i2c1: i2c@78b5000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x078b5000 0x500>;
interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c1_default>;
pinctrl-1 = <&i2c1_sleep>;
@@ -1543,9 +1543,9 @@ blsp_i2c2: i2c@78b6000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x078b6000 0x500>;
interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c2_default>;
pinctrl-1 = <&i2c2_sleep>;
@@ -1575,9 +1575,9 @@ blsp_i2c3: i2c@78b7000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x078b7000 0x500>;
interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c3_default>;
pinctrl-1 = <&i2c3_sleep>;
@@ -1607,9 +1607,9 @@ blsp_i2c4: i2c@78b8000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x078b8000 0x500>;
interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c4_default>;
pinctrl-1 = <&i2c4_sleep>;
@@ -1639,9 +1639,9 @@ blsp_i2c5: i2c@78b9000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x078b9000 0x500>;
interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c5_default>;
pinctrl-1 = <&i2c5_sleep>;
@@ -1671,9 +1671,9 @@ blsp_i2c6: i2c@78ba000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x078ba000 0x500>;
interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c6_default>;
pinctrl-1 = <&i2c6_sleep>;
diff --git a/arch/arm64/boot/dts/qcom/msm8953.dtsi b/arch/arm64/boot/dts/qcom/msm8953.dtsi
index 431228faacdd..2a70263a701d 100644
--- a/arch/arm64/boot/dts/qcom/msm8953.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8953.dtsi
@@ -923,9 +923,9 @@ i2c_1: i2c@78b5000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x78b5000 0x600>;
interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "iface", "core";
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>;
+ clock-names = "core", "iface";
+ clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c_1_default>;
@@ -941,9 +941,9 @@ i2c_2: i2c@78b6000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x78b6000 0x600>;
interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "iface", "core";
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
+ clock-names = "core", "iface";
+ clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c_2_default>;
@@ -959,9 +959,9 @@ i2c_3: i2c@78b7000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x78b7000 0x600>;
interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "iface", "core";
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
+ clock-names = "core", "iface";
+ clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c_3_default>;
pinctrl-1 = <&i2c_3_sleep>;
@@ -976,9 +976,9 @@ i2c_4: i2c@78b8000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x78b8000 0x600>;
interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "iface", "core";
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>;
+ clock-names = "core", "iface";
+ clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c_4_default>;
pinctrl-1 = <&i2c_4_sleep>;
@@ -993,9 +993,9 @@ i2c_5: i2c@7af5000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x7af5000 0x600>;
interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "iface", "core";
- clocks = <&gcc GCC_BLSP2_AHB_CLK>,
- <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>;
+ clock-names = "core", "iface";
+ clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c_5_default>;
pinctrl-1 = <&i2c_5_sleep>;
@@ -1010,9 +1010,9 @@ i2c_6: i2c@7af6000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x7af6000 0x600>;
interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "iface", "core";
- clocks = <&gcc GCC_BLSP2_AHB_CLK>,
- <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>;
+ clock-names = "core", "iface";
+ clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c_6_default>;
pinctrl-1 = <&i2c_6_sleep>;
@@ -1027,9 +1027,9 @@ i2c_7: i2c@7af7000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x7af7000 0x600>;
interrupts = <GIC_SPI 301 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "iface", "core";
- clocks = <&gcc GCC_BLSP2_AHB_CLK>,
- <&gcc GCC_BLSP2_QUP3_I2C_APPS_CLK>;
+ clock-names = "core", "iface";
+ clocks = <&gcc GCC_BLSP2_QUP3_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c_7_default>;
pinctrl-1 = <&i2c_7_sleep>;
@@ -1044,9 +1044,9 @@ i2c_8: i2c@7af8000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x7af8000 0x600>;
interrupts = <GIC_SPI 302 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "iface", "core";
- clocks = <&gcc GCC_BLSP2_AHB_CLK>,
- <&gcc GCC_BLSP2_QUP4_I2C_APPS_CLK>;
+ clock-names = "core", "iface";
+ clocks = <&gcc GCC_BLSP2_QUP4_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c_8_default>;
pinctrl-1 = <&i2c_8_sleep>;
diff --git a/arch/arm64/boot/dts/qcom/msm8994.dtsi b/arch/arm64/boot/dts/qcom/msm8994.dtsi
index 8c1dc5155b71..209f9ef030e5 100644
--- a/arch/arm64/boot/dts/qcom/msm8994.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8994.dtsi
@@ -519,9 +519,9 @@ blsp1_i2c1: i2c@f9923000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0xf9923000 0x500>;
interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
clock-frequency = <400000>;
dmas = <&blsp1_dma 12>, <&blsp1_dma 13>;
dma-names = "tx", "rx";
@@ -555,9 +555,9 @@ blsp1_i2c2: i2c@f9924000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0xf9924000 0x500>;
interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
clock-frequency = <400000>;
dmas = <&blsp1_dma 14>, <&blsp1_dma 15>;
dma-names = "tx", "rx";
@@ -575,9 +575,9 @@ blsp1_i2c4: i2c@f9926000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0xf9926000 0x500>;
interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
clock-frequency = <400000>;
dmas = <&blsp1_dma 18>, <&blsp1_dma 19>;
dma-names = "tx", "rx";
@@ -593,9 +593,9 @@ blsp1_i2c5: i2c@f9927000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0xf9927000 0x500>;
interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
clock-frequency = <400000>;
dmas = <&blsp2_dma 20>, <&blsp2_dma 21>;
dma-names = "tx", "rx";
@@ -611,9 +611,9 @@ blsp1_i2c6: i2c@f9928000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0xf9928000 0x500>;
interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
clock-frequency = <400000>;
dmas = <&blsp1_dma 22>, <&blsp1_dma 23>;
dma-names = "tx", "rx";
@@ -657,9 +657,9 @@ blsp2_i2c1: i2c@f9963000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0xf9963000 0x500>;
interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP2_AHB_CLK>,
- <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "core", "iface";
clock-frequency = <400000>;
dmas = <&blsp2_dma 12>, <&blsp2_dma 13>;
dma-names = "tx", "rx";
@@ -693,9 +693,9 @@ blsp2_i2c5: i2c@f9967000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0xf9967000 0x500>;
interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP2_AHB_CLK>,
- <&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "core", "iface";
clock-frequency = <355000>;
dmas = <&blsp2_dma 20>, <&blsp2_dma 21>;
dma-names = "tx", "rx";
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index f0f81c23c16f..dc77880e8927 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -2786,9 +2786,9 @@ blsp1_i2c3: i2c@7577000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x07577000 0x1000>;
interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp1_i2c3_default>;
pinctrl-1 = <&blsp1_i2c3_sleep>;
@@ -2834,9 +2834,9 @@ blsp2_i2c1: i2c@75b5000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x075b5000 0x1000>;
interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP2_AHB_CLK>,
- <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp2_i2c1_default>;
pinctrl-1 = <&blsp2_i2c1_sleep>;
@@ -2851,9 +2851,9 @@ blsp2_i2c2: i2c@75b6000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x075b6000 0x1000>;
interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP2_AHB_CLK>,
- <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp2_i2c2_default>;
pinctrl-1 = <&blsp2_i2c2_sleep>;
@@ -2868,9 +2868,9 @@ blsp2_i2c3: i2c@75b7000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x075b7000 0x1000>;
interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP2_AHB_CLK>,
- <&gcc GCC_BLSP2_QUP3_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP2_QUP3_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "core", "iface";
clock-frequency = <400000>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp2_i2c3_default>;
@@ -2886,9 +2886,9 @@ blsp2_i2c5: i2c@75b9000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x75b9000 0x1000>;
interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP2_AHB_CLK>,
- <&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default";
pinctrl-0 = <&blsp2_i2c5_default>;
dmas = <&blsp2_dma 20>, <&blsp2_dma 21>;
@@ -2902,9 +2902,9 @@ blsp2_i2c6: i2c@75ba000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x75ba000 0x1000>;
interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP2_AHB_CLK>,
- <&gcc GCC_BLSP2_QUP6_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP2_QUP6_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp2_i2c6_default>;
pinctrl-1 = <&blsp2_i2c6_sleep>;
diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
index 6b3a8e1006d0..acf120f91b42 100644
--- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
@@ -914,9 +914,9 @@ blsp1_i2c0: i2c@78b5000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x078b5000 0x600>;
interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP0_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP0_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default";
pinctrl-0 = <&blsp1_i2c0_default>;
#address-cells = <1>;
@@ -928,9 +928,9 @@ blsp1_spi0: spi@78b5000 {
compatible = "qcom,spi-qup-v2.2.1";
reg = <0x078b5000 0x600>;
interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP0_SPI_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP0_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default";
pinctrl-0 = <&blsp1_spi0_default>;
#address-cells = <1>;
@@ -942,9 +942,9 @@ blsp1_i2c1: i2c@78b6000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x078b6000 0x600>;
interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default";
pinctrl-0 = <&blsp1_i2c1_default>;
#address-cells = <1>;
@@ -956,9 +956,9 @@ blsp1_spi1: spi@78b6000 {
compatible = "qcom,spi-qup-v2.2.1";
reg = <0x078b6000 0x600>;
interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default";
pinctrl-0 = <&blsp1_spi1_default>;
#address-cells = <1>;
@@ -970,9 +970,9 @@ blsp1_i2c2: i2c@78b7000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x078b7000 0x600>;
interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default";
pinctrl-0 = <&blsp1_i2c2_default>;
#address-cells = <1>;
@@ -984,9 +984,9 @@ blsp1_spi2: spi@78b7000 {
compatible = "qcom,spi-qup-v2.2.1";
reg = <0x078b7000 0x600>;
interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default";
pinctrl-0 = <&blsp1_spi2_default>;
#address-cells = <1>;
@@ -998,9 +998,9 @@ blsp1_i2c3: i2c@78b8000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x078b8000 0x600>;
interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default";
pinctrl-0 = <&blsp1_i2c3_default>;
#address-cells = <1>;
@@ -1012,9 +1012,9 @@ blsp1_spi3: spi@78b8000 {
compatible = "qcom,spi-qup-v2.2.1";
reg = <0x078b8000 0x600>;
interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default";
pinctrl-0 = <&blsp1_spi3_default>;
#address-cells = <1>;
@@ -1026,9 +1026,9 @@ blsp1_i2c4: i2c@78b9000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x078b9000 0x600>;
interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default";
pinctrl-0 = <&blsp1_i2c4_default>;
#address-cells = <1>;
@@ -1040,9 +1040,9 @@ blsp1_spi4: spi@78b9000 {
compatible = "qcom,spi-qup-v2.2.1";
reg = <0x078b9000 0x600>;
interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP4_SPI_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP4_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default";
pinctrl-0 = <&blsp1_spi4_default>;
#address-cells = <1>;
@@ -1078,9 +1078,9 @@ blsp2_i2c0: i2c@7af5000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x07af5000 0x600>;
interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP2_AHB_CLK>,
- <&gcc GCC_BLSP2_QUP0_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP2_QUP0_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default";
pinctrl-0 = <&blsp2_i2c0_default>;
#address-cells = <1>;
@@ -1092,9 +1092,9 @@ blsp2_spi0: spi@7af5000 {
compatible = "qcom,spi-qup-v2.2.1";
reg = <0x07af5000 0x600>;
interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP2_AHB_CLK>,
- <&gcc GCC_BLSP2_QUP0_SPI_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP2_QUP0_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default";
pinctrl-0 = <&blsp2_spi0_default>;
#address-cells = <1>;
--
2.32.0
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v4 3/9] ARM: dts: qcom: ipq4019: align dmas in SPI/UART with DT schema
2022-04-05 6:34 [PATCH v4 0/9] dt-bindings: qcom: convert entire GSBI (QUP I2C/SPI/UART) to DT schema Krzysztof Kozlowski
2022-04-05 6:34 ` [PATCH v4 1/9] arm64: dts: qcom: align dmas in I2C/SPI/UART with " Krzysztof Kozlowski
2022-04-05 6:34 ` [PATCH v4 2/9] arm64: dts: qcom: align clocks in I2C/SPI " Krzysztof Kozlowski
@ 2022-04-05 6:34 ` Krzysztof Kozlowski
2022-04-05 6:34 ` [PATCH v4 4/9] ARM: dts: qcom: ipq4019: align clocks in I2C " Krzysztof Kozlowski
` (6 subsequent siblings)
9 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-05 6:34 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Greg Kroah-Hartman, Mark Brown, linux-arm-msm, linux-i2c,
devicetree, linux-kernel, linux-serial, linux-spi
Cc: Kuldeep Singh, Krzysztof Kozlowski
The DT schema expects dma channels in tx-rx order. No functional
change.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
Dropped Kuldeep's ack because of changes - more properties changed.
---
arch/arm/boot/dts/qcom-ipq4019.dtsi | 24 ++++++++++++------------
1 file changed, 12 insertions(+), 12 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi
index a9d0566a3190..1f6c4ab7f37e 100644
--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
@@ -253,8 +253,8 @@ blsp1_spi1: spi@78b5000 { /* BLSP1 QUP1 */
clock-names = "core", "iface";
#address-cells = <1>;
#size-cells = <0>;
- dmas = <&blsp_dma 5>, <&blsp_dma 4>;
- dma-names = "rx", "tx";
+ dmas = <&blsp_dma 4>, <&blsp_dma 5>;
+ dma-names = "tx", "rx";
status = "disabled";
};
@@ -267,8 +267,8 @@ blsp1_spi2: spi@78b6000 { /* BLSP1 QUP2 */
clock-names = "core", "iface";
#address-cells = <1>;
#size-cells = <0>;
- dmas = <&blsp_dma 7>, <&blsp_dma 6>;
- dma-names = "rx", "tx";
+ dmas = <&blsp_dma 6>, <&blsp_dma 7>;
+ dma-names = "tx", "rx";
status = "disabled";
};
@@ -281,8 +281,8 @@ blsp1_i2c3: i2c@78b7000 { /* BLSP1 QUP3 */
clock-names = "iface", "core";
#address-cells = <1>;
#size-cells = <0>;
- dmas = <&blsp_dma 9>, <&blsp_dma 8>;
- dma-names = "rx", "tx";
+ dmas = <&blsp_dma 8>, <&blsp_dma 9>;
+ dma-names = "tx", "rx";
status = "disabled";
};
@@ -295,8 +295,8 @@ blsp1_i2c4: i2c@78b8000 { /* BLSP1 QUP4 */
clock-names = "iface", "core";
#address-cells = <1>;
#size-cells = <0>;
- dmas = <&blsp_dma 11>, <&blsp_dma 10>;
- dma-names = "rx", "tx";
+ dmas = <&blsp_dma 10>, <&blsp_dma 11>;
+ dma-names = "tx", "rx";
status = "disabled";
};
@@ -382,8 +382,8 @@ blsp1_uart1: serial@78af000 {
clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
- dmas = <&blsp_dma 1>, <&blsp_dma 0>;
- dma-names = "rx", "tx";
+ dmas = <&blsp_dma 0>, <&blsp_dma 1>;
+ dma-names = "tx", "rx";
};
blsp1_uart2: serial@78b0000 {
@@ -394,8 +394,8 @@ blsp1_uart2: serial@78b0000 {
clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
- dmas = <&blsp_dma 3>, <&blsp_dma 2>;
- dma-names = "rx", "tx";
+ dmas = <&blsp_dma 2>, <&blsp_dma 3>;
+ dma-names = "tx", "rx";
};
watchdog: watchdog@b017000 {
--
2.32.0
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v4 4/9] ARM: dts: qcom: ipq4019: align clocks in I2C with DT schema
2022-04-05 6:34 [PATCH v4 0/9] dt-bindings: qcom: convert entire GSBI (QUP I2C/SPI/UART) to DT schema Krzysztof Kozlowski
` (2 preceding siblings ...)
2022-04-05 6:34 ` [PATCH v4 3/9] ARM: dts: qcom: ipq4019: align dmas in SPI/UART " Krzysztof Kozlowski
@ 2022-04-05 6:34 ` Krzysztof Kozlowski
2022-04-05 6:34 ` [PATCH v4 5/9] ARM: dts: qcom: msm8660: disable GSBI8 Krzysztof Kozlowski
` (5 subsequent siblings)
9 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-05 6:34 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Greg Kroah-Hartman, Mark Brown, linux-arm-msm, linux-i2c,
devicetree, linux-kernel, linux-serial, linux-spi
Cc: Kuldeep Singh, Krzysztof Kozlowski
The DT schema expects clocks core-iface order. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
arch/arm/boot/dts/qcom-ipq4019.dtsi | 12 ++++++------
1 file changed, 6 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi
index 1f6c4ab7f37e..897442157f5f 100644
--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
@@ -276,9 +276,9 @@ blsp1_i2c3: i2c@78b7000 { /* BLSP1 QUP3 */
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x78b7000 0x600>;
interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
#address-cells = <1>;
#size-cells = <0>;
dmas = <&blsp_dma 8>, <&blsp_dma 9>;
@@ -290,9 +290,9 @@ blsp1_i2c4: i2c@78b8000 { /* BLSP1 QUP4 */
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x78b8000 0x600>;
interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
#address-cells = <1>;
#size-cells = <0>;
dmas = <&blsp_dma 10>, <&blsp_dma 11>;
--
2.32.0
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v4 5/9] ARM: dts: qcom: msm8660: disable GSBI8
2022-04-05 6:34 [PATCH v4 0/9] dt-bindings: qcom: convert entire GSBI (QUP I2C/SPI/UART) to DT schema Krzysztof Kozlowski
` (3 preceding siblings ...)
2022-04-05 6:34 ` [PATCH v4 4/9] ARM: dts: qcom: ipq4019: align clocks in I2C " Krzysztof Kozlowski
@ 2022-04-05 6:34 ` Krzysztof Kozlowski
2022-04-05 6:34 ` [PATCH v4 6/9] spi: dt-bindings: qcom,spi-qup: convert to dtschema Krzysztof Kozlowski
` (4 subsequent siblings)
9 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-05 6:34 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Greg Kroah-Hartman, Mark Brown, linux-arm-msm, linux-i2c,
devicetree, linux-kernel, linux-serial, linux-spi
Cc: Kuldeep Singh, Krzysztof Kozlowski
The GSBI8 child node (I2C controller) is disabled, so as parent GSBI
node should be the same.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
arch/arm/boot/dts/qcom-msm8660.dtsi | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi
index a258abb23a64..47b97daecef1 100644
--- a/arch/arm/boot/dts/qcom-msm8660.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8660.dtsi
@@ -212,6 +212,7 @@ gsbi8: gsbi@19800000 {
ranges;
syscon-tcsr = <&tcsr>;
+ status = "disabled";
gsbi8_i2c: i2c@19880000 {
compatible = "qcom,i2c-qup-v1.1.1";
--
2.32.0
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v4 6/9] spi: dt-bindings: qcom,spi-qup: convert to dtschema
2022-04-05 6:34 [PATCH v4 0/9] dt-bindings: qcom: convert entire GSBI (QUP I2C/SPI/UART) to DT schema Krzysztof Kozlowski
` (4 preceding siblings ...)
2022-04-05 6:34 ` [PATCH v4 5/9] ARM: dts: qcom: msm8660: disable GSBI8 Krzysztof Kozlowski
@ 2022-04-05 6:34 ` Krzysztof Kozlowski
2022-04-05 8:34 ` Mark Brown
2022-04-05 6:34 ` [PATCH v4 7/9] dt-bindings: serial: qcom,msm-uartdm: " Krzysztof Kozlowski
` (3 subsequent siblings)
9 siblings, 1 reply; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-05 6:34 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Greg Kroah-Hartman, Mark Brown, linux-arm-msm, linux-i2c,
devicetree, linux-kernel, linux-serial, linux-spi
Cc: Kuldeep Singh, Krzysztof Kozlowski, Rob Herring
Convert the Qualcomm Universal Peripheral (QUP) Serial Peripheral
Interface (SPI) bindings to DT Schema.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Kuldeep Singh <singh.kuldeep87k@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../devicetree/bindings/spi/qcom,spi-qup.txt | 103 ------------------
.../devicetree/bindings/spi/qcom,spi-qup.yaml | 81 ++++++++++++++
2 files changed, 81 insertions(+), 103 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/spi/qcom,spi-qup.txt
create mode 100644 Documentation/devicetree/bindings/spi/qcom,spi-qup.yaml
diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt b/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt
deleted file mode 100644
index 5c090771c016..000000000000
--- a/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt
+++ /dev/null
@@ -1,103 +0,0 @@
-Qualcomm Universal Peripheral (QUP) Serial Peripheral Interface (SPI)
-
-The QUP core is an AHB slave that provides a common data path (an output FIFO
-and an input FIFO) for serial peripheral interface (SPI) mini-core.
-
-SPI in master mode supports up to 50MHz, up to four chip selects, programmable
-data path from 4 bits to 32 bits and numerous protocol variants.
-
-Required properties:
-- compatible: Should contain:
- "qcom,spi-qup-v1.1.1" for 8660, 8960 and 8064.
- "qcom,spi-qup-v2.1.1" for 8974 and later
- "qcom,spi-qup-v2.2.1" for 8974 v2 and later.
-
-- reg: Should contain base register location and length
-- interrupts: Interrupt number used by this controller
-
-- clocks: Should contain the core clock and the AHB clock.
-- clock-names: Should be "core" for the core clock and "iface" for the
- AHB clock.
-
-- #address-cells: Number of cells required to define a chip select
- address on the SPI bus. Should be set to 1.
-- #size-cells: Should be zero.
-
-Optional properties:
-- spi-max-frequency: Specifies maximum SPI clock frequency,
- Units - Hz. Definition as per
- Documentation/devicetree/bindings/spi/spi-bus.txt
-- num-cs: total number of chipselects
-- cs-gpios: should specify GPIOs used for chipselects.
- The gpios will be referred to as reg = <index> in the SPI child
- nodes. If unspecified, a single SPI device without a chip
- select can be used.
-
-- dmas: Two DMA channel specifiers following the convention outlined
- in bindings/dma/dma.txt
-- dma-names: Names for the dma channels, if present. There must be at
- least one channel named "tx" for transmit and named "rx" for
- receive.
-
-SPI slave nodes must be children of the SPI master node and can contain
-properties described in Documentation/devicetree/bindings/spi/spi-bus.txt
-
-Example:
-
- spi_8: spi@f9964000 { /* BLSP2 QUP2 */
-
- compatible = "qcom,spi-qup-v2";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0xf9964000 0x1000>;
- interrupts = <0 102 0>;
- spi-max-frequency = <19200000>;
-
- clocks = <&gcc GCC_BLSP2_QUP2_SPI_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
- clock-names = "core", "iface";
-
- dmas = <&blsp1_bam 13>, <&blsp1_bam 12>;
- dma-names = "rx", "tx";
-
- pinctrl-names = "default";
- pinctrl-0 = <&spi8_default>;
-
- device@0 {
- compatible = "arm,pl022-dummy";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <19200000>;
- spi-cpol;
- };
-
- device@1 {
- compatible = "arm,pl022-dummy";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <1>; /* Chip select 1 */
- spi-max-frequency = <9600000>;
- spi-cpha;
- };
-
- device@2 {
- compatible = "arm,pl022-dummy";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <2>; /* Chip select 2 */
- spi-max-frequency = <19200000>;
- spi-cpol;
- spi-cpha;
- };
-
- device@3 {
- compatible = "arm,pl022-dummy";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <3>; /* Chip select 3 */
- spi-max-frequency = <19200000>;
- spi-cpol;
- spi-cpha;
- spi-cs-high;
- };
- };
diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-qup.yaml b/Documentation/devicetree/bindings/spi/qcom,spi-qup.yaml
new file mode 100644
index 000000000000..93f14dd01afc
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/qcom,spi-qup.yaml
@@ -0,0 +1,81 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/qcom,spi-qup.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Universal Peripheral (QUP) Serial Peripheral Interface (SPI)
+
+maintainers:
+ - Andy Gross <agross@kernel.org>
+ - Bjorn Andersson <bjorn.andersson@linaro.org>
+ - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
+
+description:
+ The QUP core is an AHB slave that provides a common data path (an output FIFO
+ and an input FIFO) for serial peripheral interface (SPI) mini-core.
+
+ SPI in master mode supports up to 50MHz, up to four chip selects,
+ programmable data path from 4 bits to 32 bits and numerous protocol variants.
+
+allOf:
+ - $ref: /schemas/spi/spi-controller.yaml#
+
+properties:
+ compatible:
+ enum:
+ - qcom,spi-qup-v1.1.1 # for 8660, 8960 and 8064
+ - qcom,spi-qup-v2.1.1 # for 8974 and later
+ - qcom,spi-qup-v2.2.1 # for 8974 v2 and later
+
+ clocks:
+ maxItems: 2
+
+ clock-names:
+ items:
+ - const: core
+ - const: iface
+
+ dmas:
+ maxItems: 2
+
+ dma-names:
+ items:
+ - const: tx
+ - const: rx
+
+ interrupts:
+ maxItems: 1
+
+ reg:
+ maxItems: 1
+
+required:
+ - compatible
+ - clocks
+ - clock-names
+ - interrupts
+ - reg
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,gcc-msm8996.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ spi@7575000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x07575000 0x600>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp1_spi1_default>;
+ pinctrl-1 = <&blsp1_spi1_sleep>;
+ dmas = <&blsp1_dma 12>, <&blsp1_dma 13>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
--
2.32.0
^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH v4 6/9] spi: dt-bindings: qcom,spi-qup: convert to dtschema
2022-04-05 6:34 ` [PATCH v4 6/9] spi: dt-bindings: qcom,spi-qup: convert to dtschema Krzysztof Kozlowski
@ 2022-04-05 8:34 ` Mark Brown
0 siblings, 0 replies; 14+ messages in thread
From: Mark Brown @ 2022-04-05 8:34 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Greg Kroah-Hartman, linux-arm-msm, linux-i2c, devicetree,
linux-kernel, linux-serial, linux-spi, Kuldeep Singh,
Rob Herring
[-- Attachment #1: Type: text/plain, Size: 221 bytes --]
On Tue, Apr 05, 2022 at 08:34:48AM +0200, Krzysztof Kozlowski wrote:
> Convert the Qualcomm Universal Peripheral (QUP) Serial Peripheral
> Interface (SPI) bindings to DT Schema.
Acked-by: Mark Brown <broonie@kernel.org>
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v4 7/9] dt-bindings: serial: qcom,msm-uartdm: convert to dtschema
2022-04-05 6:34 [PATCH v4 0/9] dt-bindings: qcom: convert entire GSBI (QUP I2C/SPI/UART) to DT schema Krzysztof Kozlowski
` (5 preceding siblings ...)
2022-04-05 6:34 ` [PATCH v4 6/9] spi: dt-bindings: qcom,spi-qup: convert to dtschema Krzysztof Kozlowski
@ 2022-04-05 6:34 ` Krzysztof Kozlowski
2022-04-06 18:09 ` Rob Herring
2022-04-05 6:34 ` [PATCH v4 8/9] dt-bindings: i2c: qcom,i2c-qup: " Krzysztof Kozlowski
` (2 subsequent siblings)
9 siblings, 1 reply; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-05 6:34 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Greg Kroah-Hartman, Mark Brown, linux-arm-msm, linux-i2c,
devicetree, linux-kernel, linux-serial, linux-spi
Cc: Kuldeep Singh, Krzysztof Kozlowski
Convert the Qualcomm MSM Serial UARTDM bindings to DT Schema.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
.../bindings/serial/qcom,msm-uartdm.txt | 81 -------------
.../bindings/serial/qcom,msm-uartdm.yaml | 112 ++++++++++++++++++
2 files changed, 112 insertions(+), 81 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt
create mode 100644 Documentation/devicetree/bindings/serial/qcom,msm-uartdm.yaml
diff --git a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt
deleted file mode 100644
index 9d098cf73b53..000000000000
--- a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt
+++ /dev/null
@@ -1,81 +0,0 @@
-* MSM Serial UARTDM
-
-The MSM serial UARTDM hardware is designed for high-speed use cases where the
-transmit and/or receive channels can be offloaded to a dma-engine. From a
-software perspective it's mostly compatible with the MSM serial UART except
-that it supports reading and writing multiple characters at a time.
-
-Required properties:
-- compatible: Should contain at least "qcom,msm-uartdm".
- A more specific property should be specified as follows depending
- on the version:
- "qcom,msm-uartdm-v1.1"
- "qcom,msm-uartdm-v1.2"
- "qcom,msm-uartdm-v1.3"
- "qcom,msm-uartdm-v1.4"
-- reg: Should contain UART register locations and lengths. The first
- register shall specify the main control registers. An optional second
- register location shall specify the GSBI control region.
- "qcom,msm-uartdm-v1.3" is the only compatible value that might
- need the GSBI control region.
-- interrupts: Should contain UART interrupt.
-- clocks: Should contain the core clock and the AHB clock.
-- clock-names: Should be "core" for the core clock and "iface" for the
- AHB clock.
-
-Optional properties:
-- dmas: Should contain dma specifiers for transmit and receive channels
-- dma-names: Should contain "tx" for transmit and "rx" for receive channels
-- qcom,tx-crci: Identificator <u32> for Client Rate Control Interface to be
- used with TX DMA channel. Required when using DMA for transmission
- with UARTDM v1.3 and below.
-- qcom,rx-crci: Identificator <u32> for Client Rate Control Interface to be
- used with RX DMA channel. Required when using DMA for reception
- with UARTDM v1.3 and below.
-
-Note: Aliases may be defined to ensure the correct ordering of the UARTs.
-The alias serialN will result in the UART being assigned port N. If any
-serialN alias exists, then an alias must exist for each enabled UART. The
-serialN aliases should be in a .dts file instead of in a .dtsi file.
-
-Examples:
-
-- A uartdm v1.4 device with dma capabilities.
-
- serial@f991e000 {
- compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
- reg = <0xf991e000 0x1000>;
- interrupts = <0 108 0x0>;
- clocks = <&blsp1_uart2_apps_cxc>, <&blsp1_ahb_cxc>;
- clock-names = "core", "iface";
- dmas = <&dma0 0>, <&dma0 1>;
- dma-names = "tx", "rx";
- };
-
-- A uartdm v1.3 device without dma capabilities and part of a GSBI complex.
-
- serial@19c40000 {
- compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
- reg = <0x19c40000 0x1000>,
- <0x19c00000 0x1000>;
- interrupts = <0 195 0x0>;
- clocks = <&gsbi5_uart_cxc>, <&gsbi5_ahb_cxc>;
- clock-names = "core", "iface";
- };
-
-- serialN alias.
-
- aliases {
- serial0 = &uarta;
- serial1 = &uartc;
- serial2 = &uartb;
- };
-
- uarta: serial@12490000 {
- };
-
- uartb: serial@16340000 {
- };
-
- uartc: serial@1a240000 {
- };
diff --git a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.yaml b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.yaml
new file mode 100644
index 000000000000..484b9a51f6a9
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.yaml
@@ -0,0 +1,112 @@
+# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/serial/qcom,msm-uartdm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm MSM Serial UARTDM
+
+maintainers:
+ - Andy Gross <agross@kernel.org>
+ - Bjorn Andersson <bjorn.andersson@linaro.org>
+ - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
+
+description: |
+ The MSM serial UARTDM hardware is designed for high-speed use cases where the
+ transmit and/or receive channels can be offloaded to a dma-engine. From a
+ software perspective it's mostly compatible with the MSM serial UART except
+ that it supports reading and writing multiple characters at a time.
+
+ Note:: Aliases may be defined to ensure the correct ordering of the UARTs.
+ The alias serialN will result in the UART being assigned port N. If any
+ serialN alias exists, then an alias must exist for each enabled UART. The
+ serialN aliases should be in a .dts file instead of in a .dtsi file.
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - qcom,msm-uartdm-v1.1
+ - qcom,msm-uartdm-v1.2
+ - qcom,msm-uartdm-v1.3
+ - qcom,msm-uartdm-v1.4
+ - const: qcom,msm-uartdm
+
+ clocks:
+ maxItems: 2
+
+ clock-names:
+ items:
+ - const: core
+ - const: iface
+
+ dmas:
+ maxItems: 2
+
+ dma-names:
+ items:
+ - const: tx
+ - const: rx
+
+ interrupts:
+ maxItems: 1
+
+ qcom,rx-crci:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Identificator for Client Rate Control Interface to be used with RX DMA
+ channel. Required when using DMA for reception with UARTDM v1.3 and
+ below.
+
+ qcom,tx-crci:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Identificator for Client Rate Control Interface to be used with TX DMA
+ channel. Required when using DMA for transmission with UARTDM v1.3 and
+ below.
+
+ reg:
+ minItems: 1
+ items:
+ - description: Main control registers
+ - description: An optional second register location shall specify the GSBI control region.
+
+required:
+ - compatible
+ - clock-names
+ - clocks
+ - interrupts
+ - reg
+
+unevaluatedProperties: false
+
+allOf:
+ - $ref: /schemas/serial/serial.yaml#
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: qcom,msm-uartdm-v1.3
+ then:
+ properties:
+ reg:
+ minItems: 2
+ else:
+ properties:
+ reg:
+ maxItems: 1
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ serial@f991e000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0xf991e000 0x1000>;
+ interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&blsp1_uart2_apps_cxc>, <&blsp1_ahb_cxc>;
+ clock-names = "core", "iface";
+ dmas = <&dma0 0>, <&dma0 1>;
+ dma-names = "tx", "rx";
+ };
--
2.32.0
^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH v4 7/9] dt-bindings: serial: qcom,msm-uartdm: convert to dtschema
2022-04-05 6:34 ` [PATCH v4 7/9] dt-bindings: serial: qcom,msm-uartdm: " Krzysztof Kozlowski
@ 2022-04-06 18:09 ` Rob Herring
0 siblings, 0 replies; 14+ messages in thread
From: Rob Herring @ 2022-04-06 18:09 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: linux-i2c, devicetree, linux-arm-msm, Kuldeep Singh, Andy Gross,
Mark Brown, Greg Kroah-Hartman, Krzysztof Kozlowski,
linux-serial, Bjorn Andersson, Rob Herring, linux-kernel,
linux-spi
On Tue, 05 Apr 2022 08:34:49 +0200, Krzysztof Kozlowski wrote:
> Convert the Qualcomm MSM Serial UARTDM bindings to DT Schema.
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
> .../bindings/serial/qcom,msm-uartdm.txt | 81 -------------
> .../bindings/serial/qcom,msm-uartdm.yaml | 112 ++++++++++++++++++
> 2 files changed, 112 insertions(+), 81 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt
> create mode 100644 Documentation/devicetree/bindings/serial/qcom,msm-uartdm.yaml
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v4 8/9] dt-bindings: i2c: qcom,i2c-qup: convert to dtschema
2022-04-05 6:34 [PATCH v4 0/9] dt-bindings: qcom: convert entire GSBI (QUP I2C/SPI/UART) to DT schema Krzysztof Kozlowski
` (6 preceding siblings ...)
2022-04-05 6:34 ` [PATCH v4 7/9] dt-bindings: serial: qcom,msm-uartdm: " Krzysztof Kozlowski
@ 2022-04-05 6:34 ` Krzysztof Kozlowski
2022-04-15 21:10 ` Wolfram Sang
2022-04-05 6:34 ` [PATCH v4 9/9] dt-bindings: qcom: qcom,gsbi: " Krzysztof Kozlowski
2022-04-07 17:46 ` [PATCH v4 0/9] dt-bindings: qcom: convert entire GSBI (QUP I2C/SPI/UART) to DT schema Rob Herring
9 siblings, 1 reply; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-05 6:34 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Greg Kroah-Hartman, Mark Brown, linux-arm-msm, linux-i2c,
devicetree, linux-kernel, linux-serial, linux-spi
Cc: Kuldeep Singh, Krzysztof Kozlowski, Rob Herring
Convert the Qualcomm Universal Peripheral (QUP) I2C controller to DT
Schema.
Add missing properties: dma and dma-names, pinctrl states (to indicate
support for sleep pinctrl).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../devicetree/bindings/i2c/qcom,i2c-qup.txt | 40 ---------
.../devicetree/bindings/i2c/qcom,i2c-qup.yaml | 89 +++++++++++++++++++
2 files changed, 89 insertions(+), 40 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt
create mode 100644 Documentation/devicetree/bindings/i2c/qcom,i2c-qup.yaml
diff --git a/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt b/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt
deleted file mode 100644
index dc71754a56af..000000000000
--- a/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt
+++ /dev/null
@@ -1,40 +0,0 @@
-Qualcomm Universal Peripheral (QUP) I2C controller
-
-Required properties:
- - compatible: Should be:
- * "qcom,i2c-qup-v1.1.1" for 8660, 8960 and 8064.
- * "qcom,i2c-qup-v2.1.1" for 8974 v1.
- * "qcom,i2c-qup-v2.2.1" for 8974 v2 and later.
- - reg: Should contain QUP register address and length.
- - interrupts: Should contain I2C interrupt.
-
- - clocks: A list of phandles + clock-specifiers, one for each entry in
- clock-names.
- - clock-names: Should contain:
- * "core" for the core clock
- * "iface" for the AHB clock
-
- - #address-cells: Should be <1> Address cells for i2c device address
- - #size-cells: Should be <0> as i2c addresses have no size component
-
-Optional properties:
- - clock-frequency: Should specify the desired i2c bus clock frequency in Hz,
- defaults to 100kHz if omitted.
-
-Child nodes should conform to i2c bus binding.
-
-Example:
-
- i2c@f9924000 {
- compatible = "qcom,i2c-qup-v2.2.1";
- reg = <0xf9924000 0x1000>;
- interrupts = <0 96 0>;
-
- clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
- clock-names = "core", "iface";
-
- clock-frequency = <355000>;
-
- #address-cells = <1>;
- #size-cells = <0>;
- };
diff --git a/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.yaml b/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.yaml
new file mode 100644
index 000000000000..f43947514d48
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.yaml
@@ -0,0 +1,89 @@
+# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/i2c/qcom,i2c-qup.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Universal Peripheral (QUP) I2C controller
+
+maintainers:
+ - Andy Gross <agross@kernel.org>
+ - Bjorn Andersson <bjorn.andersson@linaro.org>
+ - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
+
+allOf:
+ - $ref: /schemas/i2c/i2c-controller.yaml#
+
+properties:
+ compatible:
+ enum:
+ - qcom,i2c-qup-v1.1.1 # for 8660, 8960 and 8064
+ - qcom,i2c-qup-v2.1.1 # for 8974 v1
+ - qcom,i2c-qup-v2.2.1 # for 8974 v2 and later
+
+ clocks:
+ maxItems: 2
+
+ clock-names:
+ items:
+ - const: core
+ - const: iface
+
+ clock-frequency:
+ default: 100000
+
+ dmas:
+ maxItems: 2
+
+ dma-names:
+ items:
+ - const: tx
+ - const: rx
+
+ interrupts:
+ maxItems: 1
+
+ pinctrl-0: true
+ pinctrl-1: true
+
+ pinctrl-names:
+ minItems: 1
+ items:
+ - const: default
+ - const: sleep
+
+ reg:
+ maxItems: 1
+
+required:
+ - compatible
+ - clock-names
+ - clocks
+ - interrupts
+ - reg
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,gcc-msm8998.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ i2c@c175000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x0c175000 0x600>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp1_dma 6>, <&blsp1_dma 7>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp1_i2c1_default>;
+ pinctrl-1 = <&blsp1_i2c1_sleep>;
+ clock-frequency = <400000>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
--
2.32.0
^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH v4 8/9] dt-bindings: i2c: qcom,i2c-qup: convert to dtschema
2022-04-05 6:34 ` [PATCH v4 8/9] dt-bindings: i2c: qcom,i2c-qup: " Krzysztof Kozlowski
@ 2022-04-15 21:10 ` Wolfram Sang
0 siblings, 0 replies; 14+ messages in thread
From: Wolfram Sang @ 2022-04-15 21:10 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Greg Kroah-Hartman, Mark Brown, linux-arm-msm, linux-i2c,
devicetree, linux-kernel, linux-serial, linux-spi, Kuldeep Singh,
Rob Herring
[-- Attachment #1: Type: text/plain, Size: 417 bytes --]
On Tue, Apr 05, 2022 at 08:34:50AM +0200, Krzysztof Kozlowski wrote:
> Convert the Qualcomm Universal Peripheral (QUP) I2C controller to DT
> Schema.
>
> Add missing properties: dma and dma-names, pinctrl states (to indicate
> support for sleep pinctrl).
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Reviewed-by: Rob Herring <robh@kernel.org>
Applied to for-next, thanks!
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v4 9/9] dt-bindings: qcom: qcom,gsbi: convert to dtschema
2022-04-05 6:34 [PATCH v4 0/9] dt-bindings: qcom: convert entire GSBI (QUP I2C/SPI/UART) to DT schema Krzysztof Kozlowski
` (7 preceding siblings ...)
2022-04-05 6:34 ` [PATCH v4 8/9] dt-bindings: i2c: qcom,i2c-qup: " Krzysztof Kozlowski
@ 2022-04-05 6:34 ` Krzysztof Kozlowski
2022-04-07 17:46 ` [PATCH v4 0/9] dt-bindings: qcom: convert entire GSBI (QUP I2C/SPI/UART) to DT schema Rob Herring
9 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-05 6:34 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Greg Kroah-Hartman, Mark Brown, linux-arm-msm, linux-i2c,
devicetree, linux-kernel, linux-serial, linux-spi
Cc: Kuldeep Singh, Krzysztof Kozlowski, Rob Herring
Convert the Qualcomm General Serial Bus Interface (GSBI) to DT
Schema.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../bindings/soc/qcom/qcom,gsbi.txt | 87 ------------
.../bindings/soc/qcom/qcom,gsbi.yaml | 132 ++++++++++++++++++
2 files changed, 132 insertions(+), 87 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt
create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.yaml
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt
deleted file mode 100644
index fe1855f09dcc..000000000000
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt
+++ /dev/null
@@ -1,87 +0,0 @@
-QCOM GSBI (General Serial Bus Interface) Driver
-
-The GSBI controller is modeled as a node with zero or more child nodes, each
-representing a serial sub-node device that is mux'd as part of the GSBI
-configuration settings. The mode setting will govern the input/output mode of
-the 4 GSBI IOs.
-
-Required properties:
-- compatible: Should contain "qcom,gsbi-v1.0.0"
-- cell-index: Should contain the GSBI index
-- reg: Address range for GSBI registers
-- clocks: required clock
-- clock-names: must contain "iface" entry
-- qcom,mode : indicates MUX value for configuration of the serial interface.
- Please reference dt-bindings/soc/qcom,gsbi.h for valid mux values.
-
-Optional properties:
-- qcom,crci : indicates CRCI MUX value for QUP CRCI ports. Please reference
- dt-bindings/soc/qcom,gsbi.h for valid CRCI mux values.
-- syscon-tcsr: indicates phandle of TCSR syscon node. Required if child uses
- dma.
-
-Required properties if child node exists:
-- #address-cells: Must be 1
-- #size-cells: Must be 1
-- ranges: Must be present
-
-Properties for children:
-
-A GSBI controller node can contain 0 or more child nodes representing serial
-devices. These serial devices can be a QCOM UART, I2C controller, spi
-controller, or some combination of aforementioned devices.
-
-See the following for child node definitions:
-Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt
-Documentation/devicetree/bindings/spi/qcom,spi-qup.txt
-Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt
-
-Example for APQ8064:
-
-#include <dt-bindings/soc/qcom,gsbi.h>
-
- gsbi4@16300000 {
- compatible = "qcom,gsbi-v1.0.0";
- cell-index = <4>;
- reg = <0x16300000 0x100>;
- clocks = <&gcc GSBI4_H_CLK>;
- clock-names = "iface";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- qcom,mode = <GSBI_PROT_I2C_UART>;
- qcom,crci = <GSBI_CRCI_QUP>;
-
- syscon-tcsr = <&tcsr>;
-
- /* child nodes go under here */
-
- i2c_qup4: i2c@16380000 {
- compatible = "qcom,i2c-qup-v1.1.1";
- reg = <0x16380000 0x1000>;
- interrupts = <0 153 0>;
-
- clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>;
- clock-names = "core", "iface";
-
- clock-frequency = <200000>;
-
- #address-cells = <1>;
- #size-cells = <0>;
-
- };
-
- uart4: serial@16340000 {
- compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
- reg = <0x16340000 0x1000>,
- <0x16300000 0x1000>;
- interrupts = <0 152 0x0>;
- clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
- clock-names = "core", "iface";
- };
- };
-
- tcsr: syscon@1a400000 {
- compatible = "qcom,apq8064-tcsr", "syscon";
- reg = <0x1a400000 0x100>;
- };
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.yaml
new file mode 100644
index 000000000000..c33704333e49
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.yaml
@@ -0,0 +1,132 @@
+# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/qcom/qcom,gsbi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm General Serial Bus Interface (GSBI)
+
+maintainers:
+ - Andy Gross <agross@kernel.org>
+ - Bjorn Andersson <bjorn.andersson@linaro.org>
+ - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
+
+description:
+ The GSBI controller is modeled as a node with zero or more child nodes, each
+ representing a serial sub-node device that is mux'd as part of the GSBI
+ configuration settings. The mode setting will govern the input/output mode
+ of the 4 GSBI IOs.
+
+ A GSBI controller node can contain 0 or more child nodes representing serial
+ devices. These serial devices can be a QCOM UART, I2C controller, spi
+ controller, or some combination of aforementioned devices.
+
+properties:
+ compatible:
+ const: qcom,gsbi-v1.0.0
+
+ '#address-cells':
+ const: 1
+
+ cell-index:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ The GSBI index.
+
+ clocks:
+ maxItems: 1
+
+ clock-names:
+ const: iface
+
+ qcom,crci:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ CRCI MUX value for QUP CRCI ports. Please reference
+ include/dt-bindings/soc/qcom,gsbi.h for valid CRCI mux values.
+
+ qcom,mode:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ MUX value for configuration of the serial interface. Please reference
+ include/dt-bindings/soc/qcom,gsbi.h for valid mux values.
+
+ '#size-cells':
+ const: 1
+
+ syscon-tcsr:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ Phandle of TCSR syscon node.Required if child uses dma.
+
+ ranges: true
+
+ reg:
+ maxItems: 1
+
+patternProperties:
+ "spi@[0-9a-f]+$":
+ type: object
+ $ref: /schemas/spi/qcom,spi-qup.yaml#
+
+ "i2c@[0-9a-f]+$":
+ type: object
+ $ref: /schemas/i2c/qcom,i2c-qup.yaml#
+
+ "serial@[0-9a-f]+$":
+ type: object
+ $ref: /schemas/serial/qcom,msm-uartdm.yaml#
+
+required:
+ - compatible
+ - cell-index
+ - clocks
+ - clock-names
+ - qcom,mode
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,gcc-msm8960.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/soc/qcom,gsbi.h>
+
+ gsbi@12440000 {
+ compatible = "qcom,gsbi-v1.0.0";
+ reg = <0x12440000 0x100>;
+ cell-index = <1>;
+ clocks = <&gcc GSBI1_H_CLK>;
+ clock-names = "iface";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ syscon-tcsr = <&tcsr>;
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+
+ serial@12450000 {
+ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+ reg = <0x12450000 0x100>,
+ <0x12400000 0x03>;
+ interrupts = <0 193 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GSBI1_UART_CLK>, <&gcc GSBI1_H_CLK>;
+ clock-names = "core", "iface";
+ };
+
+ i2c@12460000 {
+ compatible = "qcom,i2c-qup-v1.1.1";
+ reg = <0x12460000 0x1000>;
+ pinctrl-0 = <&i2c1_pins>;
+ pinctrl-1 = <&i2c1_pins_sleep>;
+ pinctrl-names = "default", "sleep";
+ interrupts = <0 194 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
+ clock-names = "core", "iface";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled"; /* UART chosen */
+ };
+ };
--
2.32.0
^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH v4 0/9] dt-bindings: qcom: convert entire GSBI (QUP I2C/SPI/UART) to DT schema
2022-04-05 6:34 [PATCH v4 0/9] dt-bindings: qcom: convert entire GSBI (QUP I2C/SPI/UART) to DT schema Krzysztof Kozlowski
` (8 preceding siblings ...)
2022-04-05 6:34 ` [PATCH v4 9/9] dt-bindings: qcom: qcom,gsbi: " Krzysztof Kozlowski
@ 2022-04-07 17:46 ` Rob Herring
9 siblings, 0 replies; 14+ messages in thread
From: Rob Herring @ 2022-04-07 17:46 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: Andy Gross, Bjorn Andersson, Krzysztof Kozlowski,
Greg Kroah-Hartman, Mark Brown, linux-arm-msm, linux-i2c,
devicetree, linux-kernel, linux-serial, linux-spi, Kuldeep Singh
On Tue, Apr 05, 2022 at 08:34:42AM +0200, Krzysztof Kozlowski wrote:
> Hi,
>
> Changes since v3
> ================
> 1. Correct dmas in serial/UART bindings example.
> 2. Use "const" in compatible for GSBI.
> 3. Add review tags.
>
> Changes since v2
> ================
> 1. Several new schema patches (GSBI, I2C and UART schema).
> 2. Several DTS fixes for clocks and DMAs. The choice of dma tx-rx
> and clocks core-iface was by more-or-less number of fixes needed.
> 3. Add Kuldeep acks to patches without changes.
>
> Changes since v1
> ================
> 1. Fix path in com/qcom,gsbi.txt.
> 2. Merge clock-names in example, correct $ref path (Kuldeep).
>
> Merging
> =======
> 1. The DTS patches are independent and silence warnings pointed
> out by schema.
>
> 2. The DT schema patches should be taken together as GSBI (final patch)
> depends on previous bindings.
>
> Best regards,
> Krzysztof
>
> Cc: Kuldeep Singh <singh.kuldeep87k@gmail.com>
>
> Krzysztof Kozlowski (9):
> arm64: dts: qcom: align dmas in I2C/SPI/UART with DT schema
> arm64: dts: qcom: align clocks in I2C/SPI with DT schema
> ARM: dts: qcom: ipq4019: align dmas in SPI/UART with DT schema
> ARM: dts: qcom: ipq4019: align clocks in I2C with DT schema
> ARM: dts: qcom: msm8660: disable GSBI8
> spi: dt-bindings: qcom,spi-qup: convert to dtschema
> dt-bindings: serial: qcom,msm-uartdm: convert to dtschema
> dt-bindings: i2c: qcom,i2c-qup: convert to dtschema
> dt-bindings: qcom: qcom,gsbi: convert to dtschema
Patches 6-9 applied.
Rob
^ permalink raw reply [flat|nested] 14+ messages in thread