[PATCH v1 1/8] ARM: dts: imx6qdl-vicut1/vicutgo: Set default backlight brightness to maximum

[PATCH v1 1/8] ARM: dts: imx6qdl-vicut1/vicutgo: Set default backlight brightness to maximum

[Oleksij Rempel]

From: David Jander <david@protonic.nl>

Recover default behavior of the device and set maximal brightness

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-victgo.dts   | 2 +-
 arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 227c952543d4..e6134efbfabd 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -28,7 +28,7 @@ backlight: backlight {
 		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 16 64 255>;
 		num-interpolated-steps = <16>;
-		default-brightness-level = <1>;
+		default-brightness-level = <48>;
 		power-supply = <&reg_3v3>;
 		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index 1ac7e13249d2..c1d06bc28c67 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -23,7 +23,7 @@ backlight: backlight {
 		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 16 64 255>;
 		num-interpolated-steps = <16>;
-		default-brightness-level = <1>;
+		default-brightness-level = <48>;
 		power-supply = <&reg_3v3>;
 		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
-- 
2.30.2

[PATCH v1 1/8] ARM: dts: imx6qdl-vicut1/vicutgo: Set default backlight brightness to maximum

[Oleksij Rempel]

From: David Jander <david@protonic.nl>

Recover default behavior of the device and set maximal brightness

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-victgo.dts   | 2 +-
 arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 227c952543d4..e6134efbfabd 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -28,7 +28,7 @@ backlight: backlight {
 		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 16 64 255>;
 		num-interpolated-steps = <16>;
-		default-brightness-level = <1>;
+		default-brightness-level = <48>;
 		power-supply = <&reg_3v3>;
 		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index 1ac7e13249d2..c1d06bc28c67 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -23,7 +23,7 @@ backlight: backlight {
 		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 16 64 255>;
 		num-interpolated-steps = <16>;
-		default-brightness-level = <1>;
+		default-brightness-level = <48>;
 		power-supply = <&reg_3v3>;
 		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 1/8] ARM: dts: imx6qdl-vicut1/vicutgo: Set default backlight brightness to maximum

[Oleksij Rempel]

From: David Jander <david@protonic.nl>

Recover default behavior of the device and set maximal brightness

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-victgo.dts   | 2 +-
 arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 227c952543d4..e6134efbfabd 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -28,7 +28,7 @@ backlight: backlight {
 		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 16 64 255>;
 		num-interpolated-steps = <16>;
-		default-brightness-level = <1>;
+		default-brightness-level = <48>;
 		power-supply = <&reg_3v3>;
 		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index 1ac7e13249d2..c1d06bc28c67 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -23,7 +23,7 @@ backlight: backlight {
 		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 16 64 255>;
 		num-interpolated-steps = <16>;
-		default-brightness-level = <1>;
+		default-brightness-level = <48>;
 		power-supply = <&reg_3v3>;
 		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
-- 
2.30.2

[PATCH v1 2/8] ARM: dts: imx6qdl-vicut1/vicutgo: Rename backlight to backlight_lcd

[Oleksij Rempel]

From: David Jander <david@protonic.nl>

We have two backlight sources on this boards. Use more specific name for
the LCD backlight to see the difference.

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-victgo.dts   | 4 ++--
 arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 4 ++--
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index e6134efbfabd..833340c30537 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -21,7 +21,7 @@ chosen {
 		stdout-path = &uart4;
 	};
 
-	backlight: backlight {
+	backlight_lcd: backlight {
 		compatible = "pwm-backlight";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_backlight>;
@@ -100,7 +100,7 @@ led-2 {
 
 	panel {
 		compatible = "kyo,tcg121xglp";
-		backlight = <&backlight>;
+		backlight = <&backlight_lcd>;
 		power-supply = <&reg_3v3>;
 
 		port {
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index c1d06bc28c67..a1fbbc9c26b6 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -16,7 +16,7 @@ chosen {
 		stdout-path = &uart4;
 	};
 
-	backlight: backlight {
+	backlight_lcd: backlight {
 		compatible = "pwm-backlight";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_backlight>;
@@ -102,7 +102,7 @@ led-2 {
 
 	panel {
 		compatible = "kyo,tcg121xglp";
-		backlight = <&backlight>;
+		backlight = <&backlight_lcd>;
 		power-supply = <&reg_3v3>;
 
 		port {
-- 
2.30.2

[PATCH v1 2/8] ARM: dts: imx6qdl-vicut1/vicutgo: Rename backlight to backlight_lcd

[Oleksij Rempel]

From: David Jander <david@protonic.nl>

We have two backlight sources on this boards. Use more specific name for
the LCD backlight to see the difference.

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-victgo.dts   | 4 ++--
 arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 4 ++--
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index e6134efbfabd..833340c30537 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -21,7 +21,7 @@ chosen {
 		stdout-path = &uart4;
 	};
 
-	backlight: backlight {
+	backlight_lcd: backlight {
 		compatible = "pwm-backlight";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_backlight>;
@@ -100,7 +100,7 @@ led-2 {
 
 	panel {
 		compatible = "kyo,tcg121xglp";
-		backlight = <&backlight>;
+		backlight = <&backlight_lcd>;
 		power-supply = <&reg_3v3>;
 
 		port {
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index c1d06bc28c67..a1fbbc9c26b6 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -16,7 +16,7 @@ chosen {
 		stdout-path = &uart4;
 	};
 
-	backlight: backlight {
+	backlight_lcd: backlight {
 		compatible = "pwm-backlight";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_backlight>;
@@ -102,7 +102,7 @@ led-2 {
 
 	panel {
 		compatible = "kyo,tcg121xglp";
-		backlight = <&backlight>;
+		backlight = <&backlight_lcd>;
 		power-supply = <&reg_3v3>;
 
 		port {
-- 
2.30.2

[PATCH v1 2/8] ARM: dts: imx6qdl-vicut1/vicutgo: Rename backlight to backlight_lcd

[Oleksij Rempel]

From: David Jander <david@protonic.nl>

We have two backlight sources on this boards. Use more specific name for
the LCD backlight to see the difference.

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-victgo.dts   | 4 ++--
 arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 4 ++--
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index e6134efbfabd..833340c30537 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -21,7 +21,7 @@ chosen {
 		stdout-path = &uart4;
 	};
 
-	backlight: backlight {
+	backlight_lcd: backlight {
 		compatible = "pwm-backlight";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_backlight>;
@@ -100,7 +100,7 @@ led-2 {
 
 	panel {
 		compatible = "kyo,tcg121xglp";
-		backlight = <&backlight>;
+		backlight = <&backlight_lcd>;
 		power-supply = <&reg_3v3>;
 
 		port {
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index c1d06bc28c67..a1fbbc9c26b6 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -16,7 +16,7 @@ chosen {
 		stdout-path = &uart4;
 	};
 
-	backlight: backlight {
+	backlight_lcd: backlight {
 		compatible = "pwm-backlight";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_backlight>;
@@ -102,7 +102,7 @@ led-2 {
 
 	panel {
 		compatible = "kyo,tcg121xglp";
-		backlight = <&backlight>;
+		backlight = <&backlight_lcd>;
 		power-supply = <&reg_3v3>;
 
 		port {
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 3/8] ARM: dts: imx6qdl-vicut1/vicutgo: Add backlight_led node

[Oleksij Rempel]

From: David Jander <david@protonic.nl>

backlight_led is the dimmable backlight for the rubber border on the case. It
is also used to highlight the power- and some other buttons.

MX6QDL_PAD_SD4_DAT1__PWM3_OUT is also assigned as output for pwm3. Since
we need pwm3 for the backlight, we're forced to disable user space hardware
revision detection. The bootloader will have to supply this information
(i.e. through device tree).

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-victgo.dts   | 24 +++++++++----------
 arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 33 +++++++++++++++++----------
 2 files changed, 32 insertions(+), 25 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 833340c30537..d542ddad4e32 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -33,6 +33,15 @@ backlight_lcd: backlight {
 		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
+	backlight_led: backlight_led {
+		compatible = "pwm-backlight";
+		pwms = <&pwm3 0 5000000 0>;
+		brightness-levels = <0 16 64 255>;
+		num-interpolated-steps = <16>;
+		default-brightness-level = <48>;
+		power-supply = <&reg_3v3>;
+	};
+
 	connector {
 		compatible = "composite-video-connector";
 		label = "Composite0";
@@ -392,8 +401,8 @@ &gpio1 {
 &gpio2 {
 	gpio-line-names =
 		"", "", "", "", "", "", "", "",
-		"REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4",
-			"BOARD_ID0", "BOARD_ID1", "BOARD_ID2",
+		"", "LED_PWM", "", "", "",
+			"", "", "",
 		"", "", "", "", "", "", "ISB_IN1", "ON_SWITCH",
 		"POWER_LED", "", "", "", "", "", "", "";
 };
@@ -778,17 +787,6 @@ MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21		0x1f0b0
 			/* ITU656_nPDN */
 			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20		0x1b0b0
 
-			/* HW revision detect */
-			/* REV_ID0 */
-			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08			0x1b0b0
-			/* REV_ID1 is shared with PWM3 */
-			/* REV_ID2 */
-			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10			0x1b0b0
-			/* REV_ID3 */
-			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11			0x1b0b0
-			/* REV_ID4 */
-			MX6QDL_PAD_SD4_DAT4__GPIO2_IO12			0x1b0b0
-
 			/* New in HW revision 1 */
 			/* ON1_FB */
 			MX6QDL_PAD_EIM_D20__GPIO3_IO20			0x100b0
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index a1fbbc9c26b6..2f6b263eea66 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -28,6 +28,15 @@ backlight_lcd: backlight {
 		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
+	backlight_led: backlight_led {
+		compatible = "pwm-backlight";
+		pwms = <&pwm3 0 5000000 0>;
+		brightness-levels = <0 16 64 255>;
+		num-interpolated-steps = <16>;
+		default-brightness-level = <48>;
+		power-supply = <&reg_3v3>;
+	};
+
 	connector {
 		compatible = "composite-video-connector";
 		label = "Composite0";
@@ -448,6 +457,12 @@ &pwm1 {
 	status = "okay";
 };
 
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
 &ssi1 {
 	#sound-dai-cells = <0>;
 	fsl,mode = "ac97-slave";
@@ -669,18 +684,6 @@ MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21		0x1f0b0
 			/* ITU656_nPDN */
 			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20		0x1b0b0
 
-			/* HW revision detect */
-			/* REV_ID0 */
-			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08			0x1b0b0
-			/* REV_ID1 */
-			MX6QDL_PAD_SD4_DAT1__GPIO2_IO09			0x1b0b0
-			/* REV_ID2 */
-			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10			0x1b0b0
-			/* REV_ID3 */
-			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11			0x1b0b0
-			/* REV_ID4 */
-			MX6QDL_PAD_SD4_DAT4__GPIO2_IO12			0x1b0b0
-
 			/* New in HW revision 1 */
 			/* ON1_FB */
 			MX6QDL_PAD_EIM_D20__GPIO3_IO20			0x100b0
@@ -738,6 +741,12 @@ MX6QDL_PAD_DISP0_DAT8__PWM1_OUT			0x1b0b0
 		>;
 	};
 
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT1__PWM3_OUT			0x1b0b0
+		>;
+	};
+
 	/* YaCO AUX Uart */
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
-- 
2.30.2

[PATCH v1 3/8] ARM: dts: imx6qdl-vicut1/vicutgo: Add backlight_led node

[Oleksij Rempel]

From: David Jander <david@protonic.nl>

backlight_led is the dimmable backlight for the rubber border on the case. It
is also used to highlight the power- and some other buttons.

MX6QDL_PAD_SD4_DAT1__PWM3_OUT is also assigned as output for pwm3. Since
we need pwm3 for the backlight, we're forced to disable user space hardware
revision detection. The bootloader will have to supply this information
(i.e. through device tree).

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-victgo.dts   | 24 +++++++++----------
 arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 33 +++++++++++++++++----------
 2 files changed, 32 insertions(+), 25 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 833340c30537..d542ddad4e32 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -33,6 +33,15 @@ backlight_lcd: backlight {
 		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
+	backlight_led: backlight_led {
+		compatible = "pwm-backlight";
+		pwms = <&pwm3 0 5000000 0>;
+		brightness-levels = <0 16 64 255>;
+		num-interpolated-steps = <16>;
+		default-brightness-level = <48>;
+		power-supply = <&reg_3v3>;
+	};
+
 	connector {
 		compatible = "composite-video-connector";
 		label = "Composite0";
@@ -392,8 +401,8 @@ &gpio1 {
 &gpio2 {
 	gpio-line-names =
 		"", "", "", "", "", "", "", "",
-		"REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4",
-			"BOARD_ID0", "BOARD_ID1", "BOARD_ID2",
+		"", "LED_PWM", "", "", "",
+			"", "", "",
 		"", "", "", "", "", "", "ISB_IN1", "ON_SWITCH",
 		"POWER_LED", "", "", "", "", "", "", "";
 };
@@ -778,17 +787,6 @@ MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21		0x1f0b0
 			/* ITU656_nPDN */
 			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20		0x1b0b0
 
-			/* HW revision detect */
-			/* REV_ID0 */
-			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08			0x1b0b0
-			/* REV_ID1 is shared with PWM3 */
-			/* REV_ID2 */
-			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10			0x1b0b0
-			/* REV_ID3 */
-			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11			0x1b0b0
-			/* REV_ID4 */
-			MX6QDL_PAD_SD4_DAT4__GPIO2_IO12			0x1b0b0
-
 			/* New in HW revision 1 */
 			/* ON1_FB */
 			MX6QDL_PAD_EIM_D20__GPIO3_IO20			0x100b0
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index a1fbbc9c26b6..2f6b263eea66 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -28,6 +28,15 @@ backlight_lcd: backlight {
 		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
+	backlight_led: backlight_led {
+		compatible = "pwm-backlight";
+		pwms = <&pwm3 0 5000000 0>;
+		brightness-levels = <0 16 64 255>;
+		num-interpolated-steps = <16>;
+		default-brightness-level = <48>;
+		power-supply = <&reg_3v3>;
+	};
+
 	connector {
 		compatible = "composite-video-connector";
 		label = "Composite0";
@@ -448,6 +457,12 @@ &pwm1 {
 	status = "okay";
 };
 
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
 &ssi1 {
 	#sound-dai-cells = <0>;
 	fsl,mode = "ac97-slave";
@@ -669,18 +684,6 @@ MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21		0x1f0b0
 			/* ITU656_nPDN */
 			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20		0x1b0b0
 
-			/* HW revision detect */
-			/* REV_ID0 */
-			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08			0x1b0b0
-			/* REV_ID1 */
-			MX6QDL_PAD_SD4_DAT1__GPIO2_IO09			0x1b0b0
-			/* REV_ID2 */
-			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10			0x1b0b0
-			/* REV_ID3 */
-			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11			0x1b0b0
-			/* REV_ID4 */
-			MX6QDL_PAD_SD4_DAT4__GPIO2_IO12			0x1b0b0
-
 			/* New in HW revision 1 */
 			/* ON1_FB */
 			MX6QDL_PAD_EIM_D20__GPIO3_IO20			0x100b0
@@ -738,6 +741,12 @@ MX6QDL_PAD_DISP0_DAT8__PWM1_OUT			0x1b0b0
 		>;
 	};
 
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT1__PWM3_OUT			0x1b0b0
+		>;
+	};
+
 	/* YaCO AUX Uart */
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 3/8] ARM: dts: imx6qdl-vicut1/vicutgo: Add backlight_led node

[Oleksij Rempel]

From: David Jander <david@protonic.nl>

backlight_led is the dimmable backlight for the rubber border on the case. It
is also used to highlight the power- and some other buttons.

MX6QDL_PAD_SD4_DAT1__PWM3_OUT is also assigned as output for pwm3. Since
we need pwm3 for the backlight, we're forced to disable user space hardware
revision detection. The bootloader will have to supply this information
(i.e. through device tree).

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-victgo.dts   | 24 +++++++++----------
 arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 33 +++++++++++++++++----------
 2 files changed, 32 insertions(+), 25 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 833340c30537..d542ddad4e32 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -33,6 +33,15 @@ backlight_lcd: backlight {
 		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
+	backlight_led: backlight_led {
+		compatible = "pwm-backlight";
+		pwms = <&pwm3 0 5000000 0>;
+		brightness-levels = <0 16 64 255>;
+		num-interpolated-steps = <16>;
+		default-brightness-level = <48>;
+		power-supply = <&reg_3v3>;
+	};
+
 	connector {
 		compatible = "composite-video-connector";
 		label = "Composite0";
@@ -392,8 +401,8 @@ &gpio1 {
 &gpio2 {
 	gpio-line-names =
 		"", "", "", "", "", "", "", "",
-		"REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4",
-			"BOARD_ID0", "BOARD_ID1", "BOARD_ID2",
+		"", "LED_PWM", "", "", "",
+			"", "", "",
 		"", "", "", "", "", "", "ISB_IN1", "ON_SWITCH",
 		"POWER_LED", "", "", "", "", "", "", "";
 };
@@ -778,17 +787,6 @@ MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21		0x1f0b0
 			/* ITU656_nPDN */
 			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20		0x1b0b0
 
-			/* HW revision detect */
-			/* REV_ID0 */
-			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08			0x1b0b0
-			/* REV_ID1 is shared with PWM3 */
-			/* REV_ID2 */
-			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10			0x1b0b0
-			/* REV_ID3 */
-			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11			0x1b0b0
-			/* REV_ID4 */
-			MX6QDL_PAD_SD4_DAT4__GPIO2_IO12			0x1b0b0
-
 			/* New in HW revision 1 */
 			/* ON1_FB */
 			MX6QDL_PAD_EIM_D20__GPIO3_IO20			0x100b0
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index a1fbbc9c26b6..2f6b263eea66 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -28,6 +28,15 @@ backlight_lcd: backlight {
 		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
+	backlight_led: backlight_led {
+		compatible = "pwm-backlight";
+		pwms = <&pwm3 0 5000000 0>;
+		brightness-levels = <0 16 64 255>;
+		num-interpolated-steps = <16>;
+		default-brightness-level = <48>;
+		power-supply = <&reg_3v3>;
+	};
+
 	connector {
 		compatible = "composite-video-connector";
 		label = "Composite0";
@@ -448,6 +457,12 @@ &pwm1 {
 	status = "okay";
 };
 
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
 &ssi1 {
 	#sound-dai-cells = <0>;
 	fsl,mode = "ac97-slave";
@@ -669,18 +684,6 @@ MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21		0x1f0b0
 			/* ITU656_nPDN */
 			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20		0x1b0b0
 
-			/* HW revision detect */
-			/* REV_ID0 */
-			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08			0x1b0b0
-			/* REV_ID1 */
-			MX6QDL_PAD_SD4_DAT1__GPIO2_IO09			0x1b0b0
-			/* REV_ID2 */
-			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10			0x1b0b0
-			/* REV_ID3 */
-			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11			0x1b0b0
-			/* REV_ID4 */
-			MX6QDL_PAD_SD4_DAT4__GPIO2_IO12			0x1b0b0
-
 			/* New in HW revision 1 */
 			/* ON1_FB */
 			MX6QDL_PAD_EIM_D20__GPIO3_IO20			0x100b0
@@ -738,6 +741,12 @@ MX6QDL_PAD_DISP0_DAT8__PWM1_OUT			0x1b0b0
 		>;
 	};
 
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT1__PWM3_OUT			0x1b0b0
+		>;
+	};
+
 	/* YaCO AUX Uart */
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
-- 
2.30.2

[PATCH v1 4/8] ARM: dts: imx6qdl-vicut1: update gpio-line-names for some GPIOs

[Oleksij Rempel]

From: David Jander <david@protonic.nl>

countedX lines have different board names (YACO_x). And REV_ and BOARD_ pins
have multiple functions. So, use names exposed to the OS.

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index 2f6b263eea66..ec39008c0950 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -277,9 +277,9 @@ &gpio1 {
 
 &gpio2 {
 	gpio-line-names =
-		"count0", "count1", "count2", "", "", "", "", "",
-		"REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4",
-			"BOARD_ID0", "BOARD_ID1", "BOARD_ID2",
+		"YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
+		"", "LED_PWM", "", "", "",
+			"", "", "",
 		"", "", "", "", "", "", "", "ON_SWITCH",
 		"POWER_LED", "", "ECSPI2_SS0", "", "", "", "", "";
 };
@@ -298,8 +298,10 @@ &gpio4 {
 		"", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
 		"UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
 			"CAN2_SR", "CAN2_TX", "CAN2_RX",
-		"LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "", "", "", "", "", "",
-		"", "", "", "", "BL_EN", "BL_PWM", "", "";
+		"LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "", "", "", "ON1_CTRL",
+			"ON2_CTRL", "HITCH_IN_OUT",
+		"LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
+			"ISB_LED";
 };
 
 &gpio5 {
-- 
2.30.2

[PATCH v1 4/8] ARM: dts: imx6qdl-vicut1: update gpio-line-names for some GPIOs

[Oleksij Rempel]

From: David Jander <david@protonic.nl>

countedX lines have different board names (YACO_x). And REV_ and BOARD_ pins
have multiple functions. So, use names exposed to the OS.

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index 2f6b263eea66..ec39008c0950 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -277,9 +277,9 @@ &gpio1 {
 
 &gpio2 {
 	gpio-line-names =
-		"count0", "count1", "count2", "", "", "", "", "",
-		"REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4",
-			"BOARD_ID0", "BOARD_ID1", "BOARD_ID2",
+		"YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
+		"", "LED_PWM", "", "", "",
+			"", "", "",
 		"", "", "", "", "", "", "", "ON_SWITCH",
 		"POWER_LED", "", "ECSPI2_SS0", "", "", "", "", "";
 };
@@ -298,8 +298,10 @@ &gpio4 {
 		"", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
 		"UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
 			"CAN2_SR", "CAN2_TX", "CAN2_RX",
-		"LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "", "", "", "", "", "",
-		"", "", "", "", "BL_EN", "BL_PWM", "", "";
+		"LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "", "", "", "ON1_CTRL",
+			"ON2_CTRL", "HITCH_IN_OUT",
+		"LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
+			"ISB_LED";
 };
 
 &gpio5 {
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 4/8] ARM: dts: imx6qdl-vicut1: update gpio-line-names for some GPIOs

[Oleksij Rempel]

From: David Jander <david@protonic.nl>

countedX lines have different board names (YACO_x). And REV_ and BOARD_ pins
have multiple functions. So, use names exposed to the OS.

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index 2f6b263eea66..ec39008c0950 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -277,9 +277,9 @@ &gpio1 {
 
 &gpio2 {
 	gpio-line-names =
-		"count0", "count1", "count2", "", "", "", "", "",
-		"REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4",
-			"BOARD_ID0", "BOARD_ID1", "BOARD_ID2",
+		"YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
+		"", "LED_PWM", "", "", "",
+			"", "", "",
 		"", "", "", "", "", "", "", "ON_SWITCH",
 		"POWER_LED", "", "ECSPI2_SS0", "", "", "", "", "";
 };
@@ -298,8 +298,10 @@ &gpio4 {
 		"", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
 		"UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
 			"CAN2_SR", "CAN2_TX", "CAN2_RX",
-		"LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "", "", "", "", "", "",
-		"", "", "", "", "BL_EN", "BL_PWM", "", "";
+		"LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "", "", "", "ON1_CTRL",
+			"ON2_CTRL", "HITCH_IN_OUT",
+		"LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
+			"ISB_LED";
 };
 
 &gpio5 {
-- 
2.30.2

[PATCH v1 5/8] ARM: dts: imx6qdl-vicut1/vicutgo: The sgtl5000 uses i2s not ac97

[Oleksij Rempel]

From: Robin van der Gracht <robin@protonic.nl>

According to Documentation/devicetree/bindings/sound/fsl,ssi.txt
'fsl,mode' should be specified for AC97 mode only.

The 'fsl,ssi' documentation doesn't say anything about specifying
'sound-dai-cells' so we'll remove that as well.

Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-victgo.dts   | 2 --
 arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 2 --
 2 files changed, 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index d542ddad4e32..20c7f80e5ec9 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -591,8 +591,6 @@ &pwm3 {
 };
 
 &ssi1 {
-	#sound-dai-cells = <0>;
-	fsl,mode = "ac97-slave";
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index ec39008c0950..97ef8264947a 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -466,8 +466,6 @@ &pwm3 {
 };
 
 &ssi1 {
-	#sound-dai-cells = <0>;
-	fsl,mode = "ac97-slave";
 	status = "okay";
 };
 
-- 
2.30.2

[PATCH v1 5/8] ARM: dts: imx6qdl-vicut1/vicutgo: The sgtl5000 uses i2s not ac97

[Oleksij Rempel]

From: Robin van der Gracht <robin@protonic.nl>

According to Documentation/devicetree/bindings/sound/fsl,ssi.txt
'fsl,mode' should be specified for AC97 mode only.

The 'fsl,ssi' documentation doesn't say anything about specifying
'sound-dai-cells' so we'll remove that as well.

Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-victgo.dts   | 2 --
 arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 2 --
 2 files changed, 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index d542ddad4e32..20c7f80e5ec9 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -591,8 +591,6 @@ &pwm3 {
 };
 
 &ssi1 {
-	#sound-dai-cells = <0>;
-	fsl,mode = "ac97-slave";
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index ec39008c0950..97ef8264947a 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -466,8 +466,6 @@ &pwm3 {
 };
 
 &ssi1 {
-	#sound-dai-cells = <0>;
-	fsl,mode = "ac97-slave";
 	status = "okay";
 };
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 5/8] ARM: dts: imx6qdl-vicut1/vicutgo: The sgtl5000 uses i2s not ac97

[Oleksij Rempel]

From: Robin van der Gracht <robin@protonic.nl>

According to Documentation/devicetree/bindings/sound/fsl,ssi.txt
'fsl,mode' should be specified for AC97 mode only.

The 'fsl,ssi' documentation doesn't say anything about specifying
'sound-dai-cells' so we'll remove that as well.

Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-victgo.dts   | 2 --
 arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 2 --
 2 files changed, 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index d542ddad4e32..20c7f80e5ec9 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -591,8 +591,6 @@ &pwm3 {
 };
 
 &ssi1 {
-	#sound-dai-cells = <0>;
-	fsl,mode = "ac97-slave";
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index ec39008c0950..97ef8264947a 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -466,8 +466,6 @@ &pwm3 {
 };
 
 &ssi1 {
-	#sound-dai-cells = <0>;
-	fsl,mode = "ac97-slave";
 	status = "okay";
 };
 
-- 
2.30.2

[PATCH v1 6/8] ARM: dts: imx6dl-victgo: Add interrupt-counter nodes

[Oleksij Rempel]

From: Robin van der Gracht <robin@protonic.nl>

Interrupt counter is mainlined, now we can add missing counter nodes.

Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-victgo.dts | 41 ++++++++++++++++++++++++++++-
 1 file changed, 40 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 20c7f80e5ec9..907682248aa7 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -54,6 +54,27 @@ comp0_out: endpoint {
 		};
 	};
 
+	counter-0 {
+		compatible = "interrupt-counter";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_counter0>;
+		gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+	};
+
+	counter-1 {
+		compatible = "interrupt-counter";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_counter1>;
+		gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+	};
+
+	counter-2 {
+		compatible = "interrupt-counter";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_counter2>;
+		gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
@@ -400,7 +421,7 @@ &gpio1 {
 
 &gpio2 {
 	gpio-line-names =
-		"", "", "", "", "", "", "", "",
+		"YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
 		"", "LED_PWM", "", "", "",
 			"", "", "",
 		"", "", "", "", "", "", "ISB_IN1", "ON_SWITCH",
@@ -706,6 +727,24 @@ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13			0x13008
 		>;
 	};
 
+	pinctrl_counter0: counter0grp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D0__GPIO2_IO00			0x1b000
+		>;
+	};
+
+	pinctrl_counter1: counter1grp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01			0x1b000
+		>;
+	};
+
+	pinctrl_counter2: counter2grp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D2__GPIO2_IO02			0x1b000
+		>;
+	};
+
 	pinctrl_ecspi1: ecspi1grp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D17__ECSPI1_MISO			0x100b1
-- 
2.30.2

[PATCH v1 6/8] ARM: dts: imx6dl-victgo: Add interrupt-counter nodes

[Oleksij Rempel]

From: Robin van der Gracht <robin@protonic.nl>

Interrupt counter is mainlined, now we can add missing counter nodes.

Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-victgo.dts | 41 ++++++++++++++++++++++++++++-
 1 file changed, 40 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 20c7f80e5ec9..907682248aa7 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -54,6 +54,27 @@ comp0_out: endpoint {
 		};
 	};
 
+	counter-0 {
+		compatible = "interrupt-counter";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_counter0>;
+		gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+	};
+
+	counter-1 {
+		compatible = "interrupt-counter";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_counter1>;
+		gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+	};
+
+	counter-2 {
+		compatible = "interrupt-counter";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_counter2>;
+		gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
@@ -400,7 +421,7 @@ &gpio1 {
 
 &gpio2 {
 	gpio-line-names =
-		"", "", "", "", "", "", "", "",
+		"YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
 		"", "LED_PWM", "", "", "",
 			"", "", "",
 		"", "", "", "", "", "", "ISB_IN1", "ON_SWITCH",
@@ -706,6 +727,24 @@ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13			0x13008
 		>;
 	};
 
+	pinctrl_counter0: counter0grp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D0__GPIO2_IO00			0x1b000
+		>;
+	};
+
+	pinctrl_counter1: counter1grp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01			0x1b000
+		>;
+	};
+
+	pinctrl_counter2: counter2grp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D2__GPIO2_IO02			0x1b000
+		>;
+	};
+
 	pinctrl_ecspi1: ecspi1grp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D17__ECSPI1_MISO			0x100b1
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 6/8] ARM: dts: imx6dl-victgo: Add interrupt-counter nodes

[Oleksij Rempel]

From: Robin van der Gracht <robin@protonic.nl>

Interrupt counter is mainlined, now we can add missing counter nodes.

Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-victgo.dts | 41 ++++++++++++++++++++++++++++-
 1 file changed, 40 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 20c7f80e5ec9..907682248aa7 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -54,6 +54,27 @@ comp0_out: endpoint {
 		};
 	};
 
+	counter-0 {
+		compatible = "interrupt-counter";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_counter0>;
+		gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+	};
+
+	counter-1 {
+		compatible = "interrupt-counter";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_counter1>;
+		gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+	};
+
+	counter-2 {
+		compatible = "interrupt-counter";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_counter2>;
+		gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
@@ -400,7 +421,7 @@ &gpio1 {
 
 &gpio2 {
 	gpio-line-names =
-		"", "", "", "", "", "", "", "",
+		"YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
 		"", "LED_PWM", "", "", "",
 			"", "", "",
 		"", "", "", "", "", "", "ISB_IN1", "ON_SWITCH",
@@ -706,6 +727,24 @@ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13			0x13008
 		>;
 	};
 
+	pinctrl_counter0: counter0grp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D0__GPIO2_IO00			0x1b000
+		>;
+	};
+
+	pinctrl_counter1: counter1grp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01			0x1b000
+		>;
+	};
+
+	pinctrl_counter2: counter2grp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D2__GPIO2_IO02			0x1b000
+		>;
+	};
+
 	pinctrl_ecspi1: ecspi1grp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D17__ECSPI1_MISO			0x100b1
-- 
2.30.2

[PATCH v1 7/8] ARM: dts: imx6dl-victgo: The TGO uses a lg, lb070wv8 compatible 7" display

[Oleksij Rempel]

From: Robin van der Gracht <robin@protonic.nl>

This series of devices is using lg,lb070wv8 instead of kyo,tcg121xglp.

Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-victgo.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 907682248aa7..7839021bc3eb 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -129,7 +129,7 @@ led-2 {
 	};
 
 	panel {
-		compatible = "kyo,tcg121xglp";
+		compatible = "lg,lb070wv8";
 		backlight = <&backlight_lcd>;
 		power-supply = <&reg_3v3>;
 
-- 
2.30.2

[PATCH v1 7/8] ARM: dts: imx6dl-victgo: The TGO uses a lg, lb070wv8 compatible 7" display

[Oleksij Rempel]

From: Robin van der Gracht <robin@protonic.nl>

This series of devices is using lg,lb070wv8 instead of kyo,tcg121xglp.

Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-victgo.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 907682248aa7..7839021bc3eb 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -129,7 +129,7 @@ led-2 {
 	};
 
 	panel {
-		compatible = "kyo,tcg121xglp";
+		compatible = "lg,lb070wv8";
 		backlight = <&backlight_lcd>;
 		power-supply = <&reg_3v3>;
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 7/8] ARM: dts: imx6dl-victgo: The TGO uses a lg,lb070wv8 compatible 7" display

[Oleksij Rempel]

From: Robin van der Gracht <robin@protonic.nl>

This series of devices is using lg,lb070wv8 instead of kyo,tcg121xglp.

Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-victgo.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 907682248aa7..7839021bc3eb 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -129,7 +129,7 @@ led-2 {
 	};
 
 	panel {
-		compatible = "kyo,tcg121xglp";
+		compatible = "lg,lb070wv8";
 		backlight = <&backlight_lcd>;
 		power-supply = <&reg_3v3>;
 
-- 
2.30.2

[PATCH v1 8/8] ARM: dts: imx6qdl-victgo: add CAN termination support

[Oleksij Rempel]

From: David Jander <david@protonic.nl>

The gpio1 0 pin is controlling CAN termination, not USB H1 VBUS. So,
remove wrong regulator and assign this gpio to new DT CAN termination
property.

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-victgo.dts | 12 ++----------
 1 file changed, 2 insertions(+), 10 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 7839021bc3eb..d66da630e0af 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -160,15 +160,6 @@ reg_3v3: regulator-3v3 {
 		regulator-max-microvolt = <3300000>;
 	};
 
-	reg_h1_vbus: regulator-h1-vbus {
-		compatible = "regulator-fixed";
-		regulator-name = "h1-vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
 	reg_otg_vbus: regulator-otg-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "otg-vbus";
@@ -312,6 +303,8 @@ IMX_AUDMUX_V2_PTCR_SYN		IMX_AUDMUX_V2_PDCR_RXDSEL(0)
 &can1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_can1>;
+	termination-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+	termination-ohms = <150>;
 	status = "okay";
 };
 
@@ -646,7 +639,6 @@ &uart5 {
 };
 
 &usbh1 {
-	vbus-supply = <&reg_h1_vbus>;
 	pinctrl-names = "default";
 	phy_type = "utmi";
 	dr_mode = "host";
-- 
2.30.2

[PATCH v1 8/8] ARM: dts: imx6qdl-victgo: add CAN termination support

[Oleksij Rempel]

From: David Jander <david@protonic.nl>

The gpio1 0 pin is controlling CAN termination, not USB H1 VBUS. So,
remove wrong regulator and assign this gpio to new DT CAN termination
property.

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-victgo.dts | 12 ++----------
 1 file changed, 2 insertions(+), 10 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 7839021bc3eb..d66da630e0af 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -160,15 +160,6 @@ reg_3v3: regulator-3v3 {
 		regulator-max-microvolt = <3300000>;
 	};
 
-	reg_h1_vbus: regulator-h1-vbus {
-		compatible = "regulator-fixed";
-		regulator-name = "h1-vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
 	reg_otg_vbus: regulator-otg-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "otg-vbus";
@@ -312,6 +303,8 @@ IMX_AUDMUX_V2_PTCR_SYN		IMX_AUDMUX_V2_PDCR_RXDSEL(0)
 &can1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_can1>;
+	termination-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+	termination-ohms = <150>;
 	status = "okay";
 };
 
@@ -646,7 +639,6 @@ &uart5 {
 };
 
 &usbh1 {
-	vbus-supply = <&reg_h1_vbus>;
 	pinctrl-names = "default";
 	phy_type = "utmi";
 	dr_mode = "host";
-- 
2.30.2

[PATCH v1 8/8] ARM: dts: imx6qdl-victgo: add CAN termination support

[Oleksij Rempel]

From: David Jander <david@protonic.nl>

The gpio1 0 pin is controlling CAN termination, not USB H1 VBUS. So,
remove wrong regulator and assign this gpio to new DT CAN termination
property.

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-victgo.dts | 12 ++----------
 1 file changed, 2 insertions(+), 10 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 7839021bc3eb..d66da630e0af 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -160,15 +160,6 @@ reg_3v3: regulator-3v3 {
 		regulator-max-microvolt = <3300000>;
 	};
 
-	reg_h1_vbus: regulator-h1-vbus {
-		compatible = "regulator-fixed";
-		regulator-name = "h1-vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
 	reg_otg_vbus: regulator-otg-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "otg-vbus";
@@ -312,6 +303,8 @@ IMX_AUDMUX_V2_PTCR_SYN		IMX_AUDMUX_V2_PDCR_RXDSEL(0)
 &can1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_can1>;
+	termination-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+	termination-ohms = <150>;
 	status = "okay";
 };
 
@@ -646,7 +639,6 @@ &uart5 {
 };
 
 &usbh1 {
-	vbus-supply = <&reg_h1_vbus>;
 	pinctrl-names = "default";
 	phy_type = "utmi";
 	dr_mode = "host";
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v1 1/8] ARM: dts: imx6qdl-vicut1/vicutgo: Set default backlight brightness to maximum

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:05AM +0100, Oleksij Rempel wrote:
> From: David Jander <david@protonic.nl>
> 
> Recover default behavior of the device and set maximal brightness
> 
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  arch/arm/boot/dts/imx6dl-victgo.dts   | 2 +-
>  arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 2 +-
>  2 files changed, 2 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
> index 227c952543d4..e6134efbfabd 100644
> --- a/arch/arm/boot/dts/imx6dl-victgo.dts
> +++ b/arch/arm/boot/dts/imx6dl-victgo.dts
> @@ -28,7 +28,7 @@ backlight: backlight {
>  		pwms = <&pwm1 0 5000000 0>;
>  		brightness-levels = <0 16 64 255>;
>  		num-interpolated-steps = <16>;
> -		default-brightness-level = <1>;
> +		default-brightness-level = <48>;

Please take a look at the documentation of the property.

  default-brightness-level:
    description:
      The default brightness level (index into the array defined by the
      "brightness-levels" property).

Shawn

>  		power-supply = <&reg_3v3>;
>  		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
>  	};
> diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> index 1ac7e13249d2..c1d06bc28c67 100644
> --- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> @@ -23,7 +23,7 @@ backlight: backlight {
>  		pwms = <&pwm1 0 5000000 0>;
>  		brightness-levels = <0 16 64 255>;
>  		num-interpolated-steps = <16>;
> -		default-brightness-level = <1>;
> +		default-brightness-level = <48>;
>  		power-supply = <&reg_3v3>;
>  		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
>  	};
> -- 
> 2.30.2
> 

Re: [PATCH v1 1/8] ARM: dts: imx6qdl-vicut1/vicutgo: Set default backlight brightness to maximum

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:05AM +0100, Oleksij Rempel wrote:
> From: David Jander <david@protonic.nl>
> 
> Recover default behavior of the device and set maximal brightness
> 
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  arch/arm/boot/dts/imx6dl-victgo.dts   | 2 +-
>  arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 2 +-
>  2 files changed, 2 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
> index 227c952543d4..e6134efbfabd 100644
> --- a/arch/arm/boot/dts/imx6dl-victgo.dts
> +++ b/arch/arm/boot/dts/imx6dl-victgo.dts
> @@ -28,7 +28,7 @@ backlight: backlight {
>  		pwms = <&pwm1 0 5000000 0>;
>  		brightness-levels = <0 16 64 255>;
>  		num-interpolated-steps = <16>;
> -		default-brightness-level = <1>;
> +		default-brightness-level = <48>;

Please take a look at the documentation of the property.

  default-brightness-level:
    description:
      The default brightness level (index into the array defined by the
      "brightness-levels" property).

Shawn

>  		power-supply = <&reg_3v3>;
>  		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
>  	};
> diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> index 1ac7e13249d2..c1d06bc28c67 100644
> --- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> @@ -23,7 +23,7 @@ backlight: backlight {
>  		pwms = <&pwm1 0 5000000 0>;
>  		brightness-levels = <0 16 64 255>;
>  		num-interpolated-steps = <16>;
> -		default-brightness-level = <1>;
> +		default-brightness-level = <48>;
>  		power-supply = <&reg_3v3>;
>  		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
>  	};
> -- 
> 2.30.2
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v1 1/8] ARM: dts: imx6qdl-vicut1/vicutgo: Set default backlight brightness to maximum

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:05AM +0100, Oleksij Rempel wrote:
> From: David Jander <david@protonic.nl>
> 
> Recover default behavior of the device and set maximal brightness
> 
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  arch/arm/boot/dts/imx6dl-victgo.dts   | 2 +-
>  arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 2 +-
>  2 files changed, 2 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
> index 227c952543d4..e6134efbfabd 100644
> --- a/arch/arm/boot/dts/imx6dl-victgo.dts
> +++ b/arch/arm/boot/dts/imx6dl-victgo.dts
> @@ -28,7 +28,7 @@ backlight: backlight {
>  		pwms = <&pwm1 0 5000000 0>;
>  		brightness-levels = <0 16 64 255>;
>  		num-interpolated-steps = <16>;
> -		default-brightness-level = <1>;
> +		default-brightness-level = <48>;

Please take a look at the documentation of the property.

  default-brightness-level:
    description:
      The default brightness level (index into the array defined by the
      "brightness-levels" property).

Shawn

>  		power-supply = <&reg_3v3>;
>  		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
>  	};
> diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> index 1ac7e13249d2..c1d06bc28c67 100644
> --- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> @@ -23,7 +23,7 @@ backlight: backlight {
>  		pwms = <&pwm1 0 5000000 0>;
>  		brightness-levels = <0 16 64 255>;
>  		num-interpolated-steps = <16>;
> -		default-brightness-level = <1>;
> +		default-brightness-level = <48>;
>  		power-supply = <&reg_3v3>;
>  		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
>  	};
> -- 
> 2.30.2
> 

Re: [PATCH v1 1/8] ARM: dts: imx6qdl-vicut1/vicutgo: Set default backlight brightness to maximum

[Shawn Guo]

On Wed, Apr 6, 2022 at 9:23 AM Shawn Guo <shawnguo@kernel.org> wrote:
>
> On Mon, Feb 21, 2022 at 10:53:05AM +0100, Oleksij Rempel wrote:
> > From: David Jander <david@protonic.nl>
> >
> > Recover default behavior of the device and set maximal brightness
> >
> > Signed-off-by: David Jander <david@protonic.nl>
> > Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> > ---
> >  arch/arm/boot/dts/imx6dl-victgo.dts   | 2 +-
> >  arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 2 +-
> >  2 files changed, 2 insertions(+), 2 deletions(-)
> >
> > diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
> > index 227c952543d4..e6134efbfabd 100644
> > --- a/arch/arm/boot/dts/imx6dl-victgo.dts
> > +++ b/arch/arm/boot/dts/imx6dl-victgo.dts
> > @@ -28,7 +28,7 @@ backlight: backlight {
> >               pwms = <&pwm1 0 5000000 0>;
> >               brightness-levels = <0 16 64 255>;
> >               num-interpolated-steps = <16>;
> > -             default-brightness-level = <1>;
> > +             default-brightness-level = <48>;
>
> Please take a look at the documentation of the property.
>
>   default-brightness-level:
>     description:
>       The default brightness level (index into the array defined by the
>       "brightness-levels" property).

Ah, never mind, I missed 'num-interpolated-steps' there.

Shawn

Re: [PATCH v1 1/8] ARM: dts: imx6qdl-vicut1/vicutgo: Set default backlight brightness to maximum

[Shawn Guo]

On Wed, Apr 6, 2022 at 9:23 AM Shawn Guo <shawnguo@kernel.org> wrote:
>
> On Mon, Feb 21, 2022 at 10:53:05AM +0100, Oleksij Rempel wrote:
> > From: David Jander <david@protonic.nl>
> >
> > Recover default behavior of the device and set maximal brightness
> >
> > Signed-off-by: David Jander <david@protonic.nl>
> > Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> > ---
> >  arch/arm/boot/dts/imx6dl-victgo.dts   | 2 +-
> >  arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 2 +-
> >  2 files changed, 2 insertions(+), 2 deletions(-)
> >
> > diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
> > index 227c952543d4..e6134efbfabd 100644
> > --- a/arch/arm/boot/dts/imx6dl-victgo.dts
> > +++ b/arch/arm/boot/dts/imx6dl-victgo.dts
> > @@ -28,7 +28,7 @@ backlight: backlight {
> >               pwms = <&pwm1 0 5000000 0>;
> >               brightness-levels = <0 16 64 255>;
> >               num-interpolated-steps = <16>;
> > -             default-brightness-level = <1>;
> > +             default-brightness-level = <48>;
>
> Please take a look at the documentation of the property.
>
>   default-brightness-level:
>     description:
>       The default brightness level (index into the array defined by the
>       "brightness-levels" property).

Ah, never mind, I missed 'num-interpolated-steps' there.

Shawn

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v1 1/8] ARM: dts: imx6qdl-vicut1/vicutgo: Set default backlight brightness to maximum

[Shawn Guo]

On Wed, Apr 6, 2022 at 9:23 AM Shawn Guo <shawnguo@kernel.org> wrote:
>
> On Mon, Feb 21, 2022 at 10:53:05AM +0100, Oleksij Rempel wrote:
> > From: David Jander <david@protonic.nl>
> >
> > Recover default behavior of the device and set maximal brightness
> >
> > Signed-off-by: David Jander <david@protonic.nl>
> > Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> > ---
> >  arch/arm/boot/dts/imx6dl-victgo.dts   | 2 +-
> >  arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 2 +-
> >  2 files changed, 2 insertions(+), 2 deletions(-)
> >
> > diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
> > index 227c952543d4..e6134efbfabd 100644
> > --- a/arch/arm/boot/dts/imx6dl-victgo.dts
> > +++ b/arch/arm/boot/dts/imx6dl-victgo.dts
> > @@ -28,7 +28,7 @@ backlight: backlight {
> >               pwms = <&pwm1 0 5000000 0>;
> >               brightness-levels = <0 16 64 255>;
> >               num-interpolated-steps = <16>;
> > -             default-brightness-level = <1>;
> > +             default-brightness-level = <48>;
>
> Please take a look at the documentation of the property.
>
>   default-brightness-level:
>     description:
>       The default brightness level (index into the array defined by the
>       "brightness-levels" property).

Ah, never mind, I missed 'num-interpolated-steps' there.

Shawn

Re: [PATCH v1 5/8] ARM: dts: imx6qdl-vicut1/vicutgo: The sgtl5000 uses i2s not ac97

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:09AM +0100, Oleksij Rempel wrote:
> From: Robin van der Gracht <robin@protonic.nl>
> 
> According to Documentation/devicetree/bindings/sound/fsl,ssi.txt
> 'fsl,mode' should be specified for AC97 mode only.
> 
> The 'fsl,ssi' documentation doesn't say anything about specifying
> 'sound-dai-cells' so we'll remove that as well.

Hmm, what needs to be fixed is fsl,ssi binding doc, I think.

Shawn

> 
> Signed-off-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  arch/arm/boot/dts/imx6dl-victgo.dts   | 2 --
>  arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 2 --
>  2 files changed, 4 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
> index d542ddad4e32..20c7f80e5ec9 100644
> --- a/arch/arm/boot/dts/imx6dl-victgo.dts
> +++ b/arch/arm/boot/dts/imx6dl-victgo.dts
> @@ -591,8 +591,6 @@ &pwm3 {
>  };
>  
>  &ssi1 {
> -	#sound-dai-cells = <0>;
> -	fsl,mode = "ac97-slave";
>  	status = "okay";
>  };
>  
> diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> index ec39008c0950..97ef8264947a 100644
> --- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> @@ -466,8 +466,6 @@ &pwm3 {
>  };
>  
>  &ssi1 {
> -	#sound-dai-cells = <0>;
> -	fsl,mode = "ac97-slave";
>  	status = "okay";
>  };
>  
> -- 
> 2.30.2
> 

Re: [PATCH v1 5/8] ARM: dts: imx6qdl-vicut1/vicutgo: The sgtl5000 uses i2s not ac97

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:09AM +0100, Oleksij Rempel wrote:
> From: Robin van der Gracht <robin@protonic.nl>
> 
> According to Documentation/devicetree/bindings/sound/fsl,ssi.txt
> 'fsl,mode' should be specified for AC97 mode only.
> 
> The 'fsl,ssi' documentation doesn't say anything about specifying
> 'sound-dai-cells' so we'll remove that as well.

Hmm, what needs to be fixed is fsl,ssi binding doc, I think.

Shawn

> 
> Signed-off-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  arch/arm/boot/dts/imx6dl-victgo.dts   | 2 --
>  arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 2 --
>  2 files changed, 4 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
> index d542ddad4e32..20c7f80e5ec9 100644
> --- a/arch/arm/boot/dts/imx6dl-victgo.dts
> +++ b/arch/arm/boot/dts/imx6dl-victgo.dts
> @@ -591,8 +591,6 @@ &pwm3 {
>  };
>  
>  &ssi1 {
> -	#sound-dai-cells = <0>;
> -	fsl,mode = "ac97-slave";
>  	status = "okay";
>  };
>  
> diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> index ec39008c0950..97ef8264947a 100644
> --- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> @@ -466,8 +466,6 @@ &pwm3 {
>  };
>  
>  &ssi1 {
> -	#sound-dai-cells = <0>;
> -	fsl,mode = "ac97-slave";
>  	status = "okay";
>  };
>  
> -- 
> 2.30.2
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v1 5/8] ARM: dts: imx6qdl-vicut1/vicutgo: The sgtl5000 uses i2s not ac97

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:09AM +0100, Oleksij Rempel wrote:
> From: Robin van der Gracht <robin@protonic.nl>
> 
> According to Documentation/devicetree/bindings/sound/fsl,ssi.txt
> 'fsl,mode' should be specified for AC97 mode only.
> 
> The 'fsl,ssi' documentation doesn't say anything about specifying
> 'sound-dai-cells' so we'll remove that as well.

Hmm, what needs to be fixed is fsl,ssi binding doc, I think.

Shawn

> 
> Signed-off-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  arch/arm/boot/dts/imx6dl-victgo.dts   | 2 --
>  arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 2 --
>  2 files changed, 4 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
> index d542ddad4e32..20c7f80e5ec9 100644
> --- a/arch/arm/boot/dts/imx6dl-victgo.dts
> +++ b/arch/arm/boot/dts/imx6dl-victgo.dts
> @@ -591,8 +591,6 @@ &pwm3 {
>  };
>  
>  &ssi1 {
> -	#sound-dai-cells = <0>;
> -	fsl,mode = "ac97-slave";
>  	status = "okay";
>  };
>  
> diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> index ec39008c0950..97ef8264947a 100644
> --- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> @@ -466,8 +466,6 @@ &pwm3 {
>  };
>  
>  &ssi1 {
> -	#sound-dai-cells = <0>;
> -	fsl,mode = "ac97-slave";
>  	status = "okay";
>  };
>  
> -- 
> 2.30.2
> 

Re: [PATCH v1 1/8] ARM: dts: imx6qdl-vicut1/vicutgo: Set default backlight brightness to maximum

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:05AM +0100, Oleksij Rempel wrote:
> From: David Jander <david@protonic.nl>
> 
> Recover default behavior of the device and set maximal brightness
> 
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

Applied, thanks!

Re: [PATCH v1 1/8] ARM: dts: imx6qdl-vicut1/vicutgo: Set default backlight brightness to maximum

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:05AM +0100, Oleksij Rempel wrote:
> From: David Jander <david@protonic.nl>
> 
> Recover default behavior of the device and set maximal brightness
> 
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

Applied, thanks!

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v1 1/8] ARM: dts: imx6qdl-vicut1/vicutgo: Set default backlight brightness to maximum

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:05AM +0100, Oleksij Rempel wrote:
> From: David Jander <david@protonic.nl>
> 
> Recover default behavior of the device and set maximal brightness
> 
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

Applied, thanks!

Re: [PATCH v1 2/8] ARM: dts: imx6qdl-vicut1/vicutgo: Rename backlight to backlight_lcd

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:06AM +0100, Oleksij Rempel wrote:
> From: David Jander <david@protonic.nl>
> 
> We have two backlight sources on this boards. Use more specific name for
> the LCD backlight to see the difference.
> 
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

Applied, thanks!

Re: [PATCH v1 2/8] ARM: dts: imx6qdl-vicut1/vicutgo: Rename backlight to backlight_lcd

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:06AM +0100, Oleksij Rempel wrote:
> From: David Jander <david@protonic.nl>
> 
> We have two backlight sources on this boards. Use more specific name for
> the LCD backlight to see the difference.
> 
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

Applied, thanks!

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v1 2/8] ARM: dts: imx6qdl-vicut1/vicutgo: Rename backlight to backlight_lcd

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:06AM +0100, Oleksij Rempel wrote:
> From: David Jander <david@protonic.nl>
> 
> We have two backlight sources on this boards. Use more specific name for
> the LCD backlight to see the difference.
> 
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

Applied, thanks!

Re: [PATCH v1 3/8] ARM: dts: imx6qdl-vicut1/vicutgo: Add backlight_led node

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:07AM +0100, Oleksij Rempel wrote:
> From: David Jander <david@protonic.nl>
> 
> backlight_led is the dimmable backlight for the rubber border on the case. It
> is also used to highlight the power- and some other buttons.
> 
> MX6QDL_PAD_SD4_DAT1__PWM3_OUT is also assigned as output for pwm3. Since
> we need pwm3 for the backlight, we're forced to disable user space hardware
> revision detection. The bootloader will have to supply this information
> (i.e. through device tree).
> 
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

Applied, thanks!

Re: [PATCH v1 3/8] ARM: dts: imx6qdl-vicut1/vicutgo: Add backlight_led node

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:07AM +0100, Oleksij Rempel wrote:
> From: David Jander <david@protonic.nl>
> 
> backlight_led is the dimmable backlight for the rubber border on the case. It
> is also used to highlight the power- and some other buttons.
> 
> MX6QDL_PAD_SD4_DAT1__PWM3_OUT is also assigned as output for pwm3. Since
> we need pwm3 for the backlight, we're forced to disable user space hardware
> revision detection. The bootloader will have to supply this information
> (i.e. through device tree).
> 
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

Applied, thanks!

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v1 3/8] ARM: dts: imx6qdl-vicut1/vicutgo: Add backlight_led node

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:07AM +0100, Oleksij Rempel wrote:
> From: David Jander <david@protonic.nl>
> 
> backlight_led is the dimmable backlight for the rubber border on the case. It
> is also used to highlight the power- and some other buttons.
> 
> MX6QDL_PAD_SD4_DAT1__PWM3_OUT is also assigned as output for pwm3. Since
> we need pwm3 for the backlight, we're forced to disable user space hardware
> revision detection. The bootloader will have to supply this information
> (i.e. through device tree).
> 
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

Applied, thanks!

Re: [PATCH v1 4/8] ARM: dts: imx6qdl-vicut1: update gpio-line-names for some GPIOs

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:08AM +0100, Oleksij Rempel wrote:
> From: David Jander <david@protonic.nl>
> 
> countedX lines have different board names (YACO_x). And REV_ and BOARD_ pins
> have multiple functions. So, use names exposed to the OS.
> 
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

Applied, thanks!

Re: [PATCH v1 4/8] ARM: dts: imx6qdl-vicut1: update gpio-line-names for some GPIOs

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:08AM +0100, Oleksij Rempel wrote:
> From: David Jander <david@protonic.nl>
> 
> countedX lines have different board names (YACO_x). And REV_ and BOARD_ pins
> have multiple functions. So, use names exposed to the OS.
> 
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

Applied, thanks!

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v1 4/8] ARM: dts: imx6qdl-vicut1: update gpio-line-names for some GPIOs

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:08AM +0100, Oleksij Rempel wrote:
> From: David Jander <david@protonic.nl>
> 
> countedX lines have different board names (YACO_x). And REV_ and BOARD_ pins
> have multiple functions. So, use names exposed to the OS.
> 
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

Applied, thanks!

Re: [PATCH v1 6/8] ARM: dts: imx6dl-victgo: Add interrupt-counter nodes

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:10AM +0100, Oleksij Rempel wrote:
> From: Robin van der Gracht <robin@protonic.nl>
> 
> Interrupt counter is mainlined, now we can add missing counter nodes.
> 
> Signed-off-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

Applied, thanks!

Re: [PATCH v1 6/8] ARM: dts: imx6dl-victgo: Add interrupt-counter nodes

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:10AM +0100, Oleksij Rempel wrote:
> From: Robin van der Gracht <robin@protonic.nl>
> 
> Interrupt counter is mainlined, now we can add missing counter nodes.
> 
> Signed-off-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

Applied, thanks!

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v1 6/8] ARM: dts: imx6dl-victgo: Add interrupt-counter nodes

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:10AM +0100, Oleksij Rempel wrote:
> From: Robin van der Gracht <robin@protonic.nl>
> 
> Interrupt counter is mainlined, now we can add missing counter nodes.
> 
> Signed-off-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

Applied, thanks!

Re: [PATCH v1 7/8] ARM: dts: imx6dl-victgo: The TGO uses a lg,lb070wv8 compatible 7" display

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:11AM +0100, Oleksij Rempel wrote:
> From: Robin van der Gracht <robin@protonic.nl>
> 
> This series of devices is using lg,lb070wv8 instead of kyo,tcg121xglp.
> 
> Signed-off-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

Applied, thanks!

Re: [PATCH v1 7/8] ARM: dts: imx6dl-victgo: The TGO uses a lg,lb070wv8 compatible 7" display

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:11AM +0100, Oleksij Rempel wrote:
> From: Robin van der Gracht <robin@protonic.nl>
> 
> This series of devices is using lg,lb070wv8 instead of kyo,tcg121xglp.
> 
> Signed-off-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

Applied, thanks!

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v1 7/8] ARM: dts: imx6dl-victgo: The TGO uses a lg,lb070wv8 compatible 7" display

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:11AM +0100, Oleksij Rempel wrote:
> From: Robin van der Gracht <robin@protonic.nl>
> 
> This series of devices is using lg,lb070wv8 instead of kyo,tcg121xglp.
> 
> Signed-off-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

Applied, thanks!

Re: [PATCH v1 8/8] ARM: dts: imx6qdl-victgo: add CAN termination support

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:12AM +0100, Oleksij Rempel wrote:
> From: David Jander <david@protonic.nl>
> 
> The gpio1 0 pin is controlling CAN termination, not USB H1 VBUS. So,
> remove wrong regulator and assign this gpio to new DT CAN termination
> property.
> 
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

Applied, thanks!

Re: [PATCH v1 8/8] ARM: dts: imx6qdl-victgo: add CAN termination support

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:12AM +0100, Oleksij Rempel wrote:
> From: David Jander <david@protonic.nl>
> 
> The gpio1 0 pin is controlling CAN termination, not USB H1 VBUS. So,
> remove wrong regulator and assign this gpio to new DT CAN termination
> property.
> 
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

Applied, thanks!

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v1 8/8] ARM: dts: imx6qdl-victgo: add CAN termination support

[Shawn Guo]

On Mon, Feb 21, 2022 at 10:53:12AM +0100, Oleksij Rempel wrote:
> From: David Jander <david@protonic.nl>
> 
> The gpio1 0 pin is controlling CAN termination, not USB H1 VBUS. So,
> remove wrong regulator and assign this gpio to new DT CAN termination
> property.
> 
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

Applied, thanks!