* [PATCH v1 00/17] protonic fixes
@ 2022-04-12 7:39 ` Oleksij Rempel
0 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Robin van der Gracht
This patch series provide two main part of changes:
- Remove prototype specific deprecated code not used in production.
- Unify vicut1 and victgo variants to reduce maintaining overhead.
David Jander (16):
arm: dts: imx6qdl-vicut1.dtsi: remove TiWi module
arm: dts: imx6qdl-vicut1.dtsi: Put nON_SWITCH in own pinctrl grp
arm: dts: imx6qdl-vicut1.dtsi: Remove PCIe
arm: dts: imx6qdl-vicut1/victgo: Remove UART2
arm: dts: imx6qdl-vicut1.dtsi: Fix LED names
arm: dts: imx6qdl-vicut1.dtsi: Fix debug LED gpio pins
arm: dts: imx6qdl-vicut1.dtsi: Update GPIO line names
arm: dts: imx6qdl-vicut1.dtsi: Remove conflicting pinctrl entry
arm: dts: imx6q-vicut1.dts: remove sata node
arm: dts: imx6dl-victgo.dts: update gpio names
arm: dts: imx6dl-victgo.dts: Factor out common parts to
imx6qdl-victgo.dtsi
arm: dts: imx6qdl-vicut1.dtsi: Move some node out to DTS files
arm: dts: Remove imx6qdl-victgo.dtsi
arm: dts: imx6qdl-vicut1: Factor out common parts of 12inch board
variants
arm: dts: imx6dl-victgo.dts: Remove touchscreen x axis inversion
arm: dts: imx6qdl-vicut1.dtsi: Add missing ISB led node
Oleksij Rempel (1):
arm: dts: imx6qdl-vicut1.dtsi: add thermal zone and attach tmp103 to
it.
arch/arm/boot/dts/imx6dl-victgo.dts | 682 +------------------
arch/arm/boot/dts/imx6dl-vicut1.dts | 1 +
arch/arm/boot/dts/imx6q-vicut1.dts | 5 +-
arch/arm/boot/dts/imx6qdl-vicut1-12inch.dtsi | 128 ++++
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 222 +-----
arch/arm/boot/dts/imx6qp-vicutp.dts | 1 +
6 files changed, 178 insertions(+), 861 deletions(-)
create mode 100644 arch/arm/boot/dts/imx6qdl-vicut1-12inch.dtsi
--
2.30.2
^ permalink raw reply [flat|nested] 42+ messages in thread* [PATCH v1 01/17] arm: dts: imx6qdl-vicut1.dtsi: remove TiWi module
2022-04-12 7:39 ` Oleksij Rempel
@ 2022-04-12 7:39 ` Oleksij Rempel
-1 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
Only the first prototypes had a TiWi module. There is no publicly available
hardware where this module is fitted and there are no plant to produce
any.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 51 ---------------------------
1 file changed, 51 deletions(-)
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index ec39008c0950..fe2685642bf1 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -144,18 +144,6 @@ reg_otg_vbus: regulator-otg-vbus {
enable-active-high;
};
- reg_wifi: regulator-wifi {
- compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_wifi_npd>;
- regulator-name = "wifi";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- startup-delay-us = <70000>;
- };
-
sound {
compatible = "simple-audio-card";
simple-audio-card,name = "prti6q-sgtl5000";
@@ -530,26 +518,6 @@ &usdhc1 {
status = "okay";
};
-&usdhc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc2>;
- vmmc-supply = <®_wifi>;
- non-removable;
- cap-power-off-card;
- keep-power-in-suspend;
- no-1-8-v;
- no-mmc;
- no-sd;
- status = "okay";
-
- wifi {
- compatible = "ti,wl1271";
- interrupts-extended = <&gpio1 30 IRQ_TYPE_LEVEL_HIGH>;
- ref-clock-frequency = "38400000";
- tcxo-clock-frequency = "19200000";
- };
-};
-
&usdhc3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc3>;
@@ -808,19 +776,6 @@ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
>;
};
- pinctrl_usdhc2: usdhc2grp {
- fsl,pins = <
- MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
- MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
- MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
- MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
- MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
- MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
- /* WL12xx IRQ */
- MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x10880
- >;
- };
-
pinctrl_usdhc3: usdhc3grp {
fsl,pins = <
MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
@@ -836,10 +791,4 @@ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
>;
};
-
- pinctrl_wifi_npd: wifinpdgrp {
- fsl,pins = <
- MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b8b0
- >;
- };
};
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 42+ messages in thread* [PATCH v1 01/17] arm: dts: imx6qdl-vicut1.dtsi: remove TiWi module
@ 2022-04-12 7:39 ` Oleksij Rempel
0 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
Only the first prototypes had a TiWi module. There is no publicly available
hardware where this module is fitted and there are no plant to produce
any.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 51 ---------------------------
1 file changed, 51 deletions(-)
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index ec39008c0950..fe2685642bf1 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -144,18 +144,6 @@ reg_otg_vbus: regulator-otg-vbus {
enable-active-high;
};
- reg_wifi: regulator-wifi {
- compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_wifi_npd>;
- regulator-name = "wifi";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- startup-delay-us = <70000>;
- };
-
sound {
compatible = "simple-audio-card";
simple-audio-card,name = "prti6q-sgtl5000";
@@ -530,26 +518,6 @@ &usdhc1 {
status = "okay";
};
-&usdhc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc2>;
- vmmc-supply = <®_wifi>;
- non-removable;
- cap-power-off-card;
- keep-power-in-suspend;
- no-1-8-v;
- no-mmc;
- no-sd;
- status = "okay";
-
- wifi {
- compatible = "ti,wl1271";
- interrupts-extended = <&gpio1 30 IRQ_TYPE_LEVEL_HIGH>;
- ref-clock-frequency = "38400000";
- tcxo-clock-frequency = "19200000";
- };
-};
-
&usdhc3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc3>;
@@ -808,19 +776,6 @@ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
>;
};
- pinctrl_usdhc2: usdhc2grp {
- fsl,pins = <
- MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
- MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
- MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
- MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
- MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
- MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
- /* WL12xx IRQ */
- MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x10880
- >;
- };
-
pinctrl_usdhc3: usdhc3grp {
fsl,pins = <
MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
@@ -836,10 +791,4 @@ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
>;
};
-
- pinctrl_wifi_npd: wifinpdgrp {
- fsl,pins = <
- MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b8b0
- >;
- };
};
--
2.30.2
^ permalink raw reply related [flat|nested] 42+ messages in thread* Re: [PATCH v1 01/17] arm: dts: imx6qdl-vicut1.dtsi: remove TiWi module
2022-04-12 7:39 ` Oleksij Rempel
@ 2022-04-18 11:49 ` Shawn Guo
-1 siblings, 0 replies; 42+ messages in thread
From: Shawn Guo @ 2022-04-18 11:49 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Rob Herring, David Jander, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
On Tue, Apr 12, 2022 at 09:39:48AM +0200, Oleksij Rempel wrote:
> From: David Jander <david@protonic.nl>
>
> Only the first prototypes had a TiWi module. There is no publicly available
> hardware where this module is fitted and there are no plant to produce
s/plant/plan?
Shawn
> any.
>
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
> arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 51 ---------------------------
> 1 file changed, 51 deletions(-)
>
> diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> index ec39008c0950..fe2685642bf1 100644
> --- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> @@ -144,18 +144,6 @@ reg_otg_vbus: regulator-otg-vbus {
> enable-active-high;
> };
>
> - reg_wifi: regulator-wifi {
> - compatible = "regulator-fixed";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_wifi_npd>;
> - regulator-name = "wifi";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
> - enable-active-high;
> - startup-delay-us = <70000>;
> - };
> -
> sound {
> compatible = "simple-audio-card";
> simple-audio-card,name = "prti6q-sgtl5000";
> @@ -530,26 +518,6 @@ &usdhc1 {
> status = "okay";
> };
>
> -&usdhc2 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_usdhc2>;
> - vmmc-supply = <®_wifi>;
> - non-removable;
> - cap-power-off-card;
> - keep-power-in-suspend;
> - no-1-8-v;
> - no-mmc;
> - no-sd;
> - status = "okay";
> -
> - wifi {
> - compatible = "ti,wl1271";
> - interrupts-extended = <&gpio1 30 IRQ_TYPE_LEVEL_HIGH>;
> - ref-clock-frequency = "38400000";
> - tcxo-clock-frequency = "19200000";
> - };
> -};
> -
> &usdhc3 {
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_usdhc3>;
> @@ -808,19 +776,6 @@ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
> >;
> };
>
> - pinctrl_usdhc2: usdhc2grp {
> - fsl,pins = <
> - MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
> - MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
> - MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
> - MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
> - MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
> - MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
> - /* WL12xx IRQ */
> - MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x10880
> - >;
> - };
> -
> pinctrl_usdhc3: usdhc3grp {
> fsl,pins = <
> MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
> @@ -836,10 +791,4 @@ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
> MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
> >;
> };
> -
> - pinctrl_wifi_npd: wifinpdgrp {
> - fsl,pins = <
> - MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b8b0
> - >;
> - };
> };
> --
> 2.30.2
>
^ permalink raw reply [flat|nested] 42+ messages in thread* Re: [PATCH v1 01/17] arm: dts: imx6qdl-vicut1.dtsi: remove TiWi module
@ 2022-04-18 11:49 ` Shawn Guo
0 siblings, 0 replies; 42+ messages in thread
From: Shawn Guo @ 2022-04-18 11:49 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Rob Herring, David Jander, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
On Tue, Apr 12, 2022 at 09:39:48AM +0200, Oleksij Rempel wrote:
> From: David Jander <david@protonic.nl>
>
> Only the first prototypes had a TiWi module. There is no publicly available
> hardware where this module is fitted and there are no plant to produce
s/plant/plan?
Shawn
> any.
>
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
> arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 51 ---------------------------
> 1 file changed, 51 deletions(-)
>
> diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> index ec39008c0950..fe2685642bf1 100644
> --- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
> @@ -144,18 +144,6 @@ reg_otg_vbus: regulator-otg-vbus {
> enable-active-high;
> };
>
> - reg_wifi: regulator-wifi {
> - compatible = "regulator-fixed";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_wifi_npd>;
> - regulator-name = "wifi";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
> - enable-active-high;
> - startup-delay-us = <70000>;
> - };
> -
> sound {
> compatible = "simple-audio-card";
> simple-audio-card,name = "prti6q-sgtl5000";
> @@ -530,26 +518,6 @@ &usdhc1 {
> status = "okay";
> };
>
> -&usdhc2 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_usdhc2>;
> - vmmc-supply = <®_wifi>;
> - non-removable;
> - cap-power-off-card;
> - keep-power-in-suspend;
> - no-1-8-v;
> - no-mmc;
> - no-sd;
> - status = "okay";
> -
> - wifi {
> - compatible = "ti,wl1271";
> - interrupts-extended = <&gpio1 30 IRQ_TYPE_LEVEL_HIGH>;
> - ref-clock-frequency = "38400000";
> - tcxo-clock-frequency = "19200000";
> - };
> -};
> -
> &usdhc3 {
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_usdhc3>;
> @@ -808,19 +776,6 @@ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
> >;
> };
>
> - pinctrl_usdhc2: usdhc2grp {
> - fsl,pins = <
> - MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
> - MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
> - MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
> - MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
> - MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
> - MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
> - /* WL12xx IRQ */
> - MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x10880
> - >;
> - };
> -
> pinctrl_usdhc3: usdhc3grp {
> fsl,pins = <
> MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
> @@ -836,10 +791,4 @@ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
> MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
> >;
> };
> -
> - pinctrl_wifi_npd: wifinpdgrp {
> - fsl,pins = <
> - MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b8b0
> - >;
> - };
> };
> --
> 2.30.2
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 42+ messages in thread
* [PATCH v1 02/17] arm: dts: imx6qdl-vicut1.dtsi: Put nON_SWITCH in own pinctrl grp
2022-04-12 7:39 ` Oleksij Rempel
@ 2022-04-12 7:39 ` Oleksij Rempel
-1 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
Unify nON_SWITCH pinctrl configuration with imx6dl-victgo.dts.
This patch is a preparation to reduce duplicated code between vicut1 and
victgo.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 11 +++++++++--
1 file changed, 9 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index fe2685642bf1..32f7eb379e60 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -72,6 +72,8 @@ counter-2 {
gpio-keys {
compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiokeys>;
autorepeat;
power {
@@ -621,6 +623,13 @@ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
>;
};
+ pinctrl_gpiokeys: gpiokeygrp {
+ fsl,pins = <
+ /* nON_SWITCH */
+ MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
+ >;
+ };
+
pinctrl_hog: hoggrp {
fsl,pins = <
/* ITU656_nRESET */
@@ -631,8 +640,6 @@ MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x130b0
MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x130b0
/* CAM_nDETECT */
MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
- /* nON_SWITCH */
- MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
/* ISB_IN1 */
MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x130b0
/* ISB_nIN2 */
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 42+ messages in thread* [PATCH v1 02/17] arm: dts: imx6qdl-vicut1.dtsi: Put nON_SWITCH in own pinctrl grp
@ 2022-04-12 7:39 ` Oleksij Rempel
0 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
Unify nON_SWITCH pinctrl configuration with imx6dl-victgo.dts.
This patch is a preparation to reduce duplicated code between vicut1 and
victgo.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 11 +++++++++--
1 file changed, 9 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index fe2685642bf1..32f7eb379e60 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -72,6 +72,8 @@ counter-2 {
gpio-keys {
compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiokeys>;
autorepeat;
power {
@@ -621,6 +623,13 @@ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
>;
};
+ pinctrl_gpiokeys: gpiokeygrp {
+ fsl,pins = <
+ /* nON_SWITCH */
+ MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
+ >;
+ };
+
pinctrl_hog: hoggrp {
fsl,pins = <
/* ITU656_nRESET */
@@ -631,8 +640,6 @@ MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x130b0
MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x130b0
/* CAM_nDETECT */
MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
- /* nON_SWITCH */
- MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
/* ISB_IN1 */
MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x130b0
/* ISB_nIN2 */
--
2.30.2
^ permalink raw reply related [flat|nested] 42+ messages in thread
* [PATCH v1 03/17] arm: dts: imx6qdl-vicut1.dtsi: Remove PCIe
2022-04-12 7:39 ` Oleksij Rempel
@ 2022-04-12 7:39 ` Oleksij Rempel
-1 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
Only the very first prototypes had PCIe and there are no plant to add it
in the future.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 8 ++------
1 file changed, 2 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index 32f7eb379e60..b126ef4d5255 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -296,8 +296,8 @@ &gpio4 {
&gpio5 {
gpio-line-names =
- "", "", "", "", "", "PCIE_WAKE", "PCIE_CLKREQ", "PCIE_W_DIS",
- "PCIE_RESET", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
"", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
"I2S_BITCLK", "I2S_DOUT",
"I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
@@ -439,10 +439,6 @@ lvds0_out: endpoint {
};
};
-&pcie {
- status = "okay";
-};
-
&pwm1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm1>;
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 42+ messages in thread* [PATCH v1 03/17] arm: dts: imx6qdl-vicut1.dtsi: Remove PCIe
@ 2022-04-12 7:39 ` Oleksij Rempel
0 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
Only the very first prototypes had PCIe and there are no plant to add it
in the future.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 8 ++------
1 file changed, 2 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index 32f7eb379e60..b126ef4d5255 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -296,8 +296,8 @@ &gpio4 {
&gpio5 {
gpio-line-names =
- "", "", "", "", "", "PCIE_WAKE", "PCIE_CLKREQ", "PCIE_W_DIS",
- "PCIE_RESET", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
"", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
"I2S_BITCLK", "I2S_DOUT",
"I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
@@ -439,10 +439,6 @@ lvds0_out: endpoint {
};
};
-&pcie {
- status = "okay";
-};
-
&pwm1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm1>;
--
2.30.2
^ permalink raw reply related [flat|nested] 42+ messages in thread
* [PATCH v1 04/17] arm: dts: imx6qdl-vicut1/victgo: Remove UART2
2022-04-12 7:39 ` Oleksij Rempel
@ 2022-04-12 7:39 ` Oleksij Rempel
-1 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
Only first prototype had UART2 and there are no plans to add it in the
future.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-victgo.dts | 13 -------------
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 15 ---------------
2 files changed, 28 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 7dd7fb165432..9cf4df3eaeb0 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -616,12 +616,6 @@ &uart1 {
status = "okay";
};
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
- status = "okay";
-};
-
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
@@ -905,13 +899,6 @@ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
>;
};
- pinctrl_uart2: uart2grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
- >;
- };
-
/* YaCO Touchscreen UART */
pinctrl_uart3: uart3grp {
fsl,pins = <
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index b126ef4d5255..ea474aa93485 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -463,12 +463,6 @@ &uart1 {
status = "okay";
};
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
- status = "okay";
-};
-
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
@@ -728,15 +722,6 @@ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
>;
};
- pinctrl_uart2: uart2grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x1b0b1
- MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B 0x1b0b1
- >;
- };
-
/* YaCO Touchscreen UART */
pinctrl_uart3: uart3grp {
fsl,pins = <
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 42+ messages in thread* [PATCH v1 04/17] arm: dts: imx6qdl-vicut1/victgo: Remove UART2
@ 2022-04-12 7:39 ` Oleksij Rempel
0 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
Only first prototype had UART2 and there are no plans to add it in the
future.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-victgo.dts | 13 -------------
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 15 ---------------
2 files changed, 28 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 7dd7fb165432..9cf4df3eaeb0 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -616,12 +616,6 @@ &uart1 {
status = "okay";
};
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
- status = "okay";
-};
-
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
@@ -905,13 +899,6 @@ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
>;
};
- pinctrl_uart2: uart2grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
- >;
- };
-
/* YaCO Touchscreen UART */
pinctrl_uart3: uart3grp {
fsl,pins = <
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index b126ef4d5255..ea474aa93485 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -463,12 +463,6 @@ &uart1 {
status = "okay";
};
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
- status = "okay";
-};
-
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
@@ -728,15 +722,6 @@ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
>;
};
- pinctrl_uart2: uart2grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x1b0b1
- MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B 0x1b0b1
- >;
- };
-
/* YaCO Touchscreen UART */
pinctrl_uart3: uart3grp {
fsl,pins = <
--
2.30.2
^ permalink raw reply related [flat|nested] 42+ messages in thread
* [PATCH v1 05/17] arm: dts: imx6qdl-vicut1.dtsi: Fix LED names
2022-04-12 7:39 ` Oleksij Rempel
@ 2022-04-12 7:39 ` Oleksij Rempel
-1 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
The names should be consistent with the names in imx6dl-victgo.dts
This patch is preparation to unify vicut1 and victgo DTs.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index ea474aa93485..b7a705b39178 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -90,21 +90,21 @@ leds {
pinctrl-0 = <&pinctrl_leds>;
led-0 {
- label = "LED_DI0_DEBUG_0";
+ label = "debug0";
function = LED_FUNCTION_HEARTBEAT;
gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
led-1 {
- label = "LED_DI0_DEBUG_1";
+ label = "debug1";
function = LED_FUNCTION_DISK;
gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "disk-activity";
};
led-2 {
- label = "POWER_LED";
+ label = "power_led";
function = LED_FUNCTION_POWER;
gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
default-state = "on";
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 42+ messages in thread* [PATCH v1 05/17] arm: dts: imx6qdl-vicut1.dtsi: Fix LED names
@ 2022-04-12 7:39 ` Oleksij Rempel
0 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
The names should be consistent with the names in imx6dl-victgo.dts
This patch is preparation to unify vicut1 and victgo DTs.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index ea474aa93485..b7a705b39178 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -90,21 +90,21 @@ leds {
pinctrl-0 = <&pinctrl_leds>;
led-0 {
- label = "LED_DI0_DEBUG_0";
+ label = "debug0";
function = LED_FUNCTION_HEARTBEAT;
gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
led-1 {
- label = "LED_DI0_DEBUG_1";
+ label = "debug1";
function = LED_FUNCTION_DISK;
gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "disk-activity";
};
led-2 {
- label = "POWER_LED";
+ label = "power_led";
function = LED_FUNCTION_POWER;
gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
default-state = "on";
--
2.30.2
^ permalink raw reply related [flat|nested] 42+ messages in thread
* [PATCH v1 06/17] arm: dts: imx6qdl-vicut1.dtsi: Fix debug LED gpio pins
2022-04-12 7:39 ` Oleksij Rempel
@ 2022-04-12 7:39 ` Oleksij Rempel
-1 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
While there are LEDs connected on some variants on GPIO4 pins 16 and 17,
those are not the debug LEDs that should be visible to user-space.
It should be the same as in imx6dl-victgo.dtsi.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index b7a705b39178..a5f962f1028b 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -92,14 +92,14 @@ leds {
led-0 {
label = "debug0";
function = LED_FUNCTION_HEARTBEAT;
- gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
led-1 {
label = "debug1";
function = LED_FUNCTION_DISK;
- gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "disk-activity";
};
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 42+ messages in thread* [PATCH v1 06/17] arm: dts: imx6qdl-vicut1.dtsi: Fix debug LED gpio pins
@ 2022-04-12 7:39 ` Oleksij Rempel
0 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
While there are LEDs connected on some variants on GPIO4 pins 16 and 17,
those are not the debug LEDs that should be visible to user-space.
It should be the same as in imx6dl-victgo.dtsi.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index b7a705b39178..a5f962f1028b 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -92,14 +92,14 @@ leds {
led-0 {
label = "debug0";
function = LED_FUNCTION_HEARTBEAT;
- gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
led-1 {
label = "debug1";
function = LED_FUNCTION_DISK;
- gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "disk-activity";
};
--
2.30.2
^ permalink raw reply related [flat|nested] 42+ messages in thread
* [PATCH v1 07/17] arm: dts: imx6qdl-vicut1.dtsi: Update GPIO line names
2022-04-12 7:39 ` Oleksij Rempel
@ 2022-04-12 7:39 ` Oleksij Rempel
-1 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
Add some missing names and remove names to pins that have never been used
and/or are not present on any hardware.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 19 +++++++++----------
1 file changed, 9 insertions(+), 10 deletions(-)
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index a5f962f1028b..a93e7f8302aa 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -257,12 +257,10 @@ &gpio1 {
gpio-line-names =
"CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
"CAM2_MIRROR", "", "", "SMBALERT",
- "DEBUG_0", "DEBUG_1", "SDIO_SCK", "SDIO_CMD", "SDIO_D3",
- "SDIO_D2", "SDIO_D1", "SDIO_D0",
+ "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
"SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
- "SD1_DATA3", "", "",
- "", "ETH_RESET", "WIFI_PD", "WIFI_BT_RST", "ETH_INT", "",
- "WL_IRQ", "ETH_MDC";
+ "SD1_DATA3", "ETH_MDIO", "",
+ "", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
};
&gpio2 {
@@ -270,8 +268,8 @@ &gpio2 {
"YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
"", "LED_PWM", "", "", "",
"", "", "",
- "", "", "", "", "", "", "", "ON_SWITCH",
- "POWER_LED", "", "ECSPI2_SS0", "", "", "", "", "";
+ "", "", "", "", "", "ISB_IN2", "ISB_nIN1", "ON_SWITCH",
+ "POWER_LED", "", "", "", "", "", "", "";
};
&gpio3 {
@@ -280,7 +278,8 @@ &gpio3 {
"", "", "", "", "", "", "", "",
"ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
"CPU_ON1_FB", "USB_OTG_OC", "USB_OTG_PWR", "YACO_IRQ",
- "", "", "", "", "", "", "", "";
+ "TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0",
+ "YACO_RESET";
};
&gpio4 {
@@ -288,8 +287,8 @@ &gpio4 {
"", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
"UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
"CAN2_SR", "CAN2_TX", "CAN2_RX",
- "LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "", "", "", "ON1_CTRL",
- "ON2_CTRL", "HITCH_IN_OUT",
+ "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
+ "HITCH_IN_OUT",
"LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
"ISB_LED";
};
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 42+ messages in thread* [PATCH v1 07/17] arm: dts: imx6qdl-vicut1.dtsi: Update GPIO line names
@ 2022-04-12 7:39 ` Oleksij Rempel
0 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
Add some missing names and remove names to pins that have never been used
and/or are not present on any hardware.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 19 +++++++++----------
1 file changed, 9 insertions(+), 10 deletions(-)
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index a5f962f1028b..a93e7f8302aa 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -257,12 +257,10 @@ &gpio1 {
gpio-line-names =
"CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
"CAM2_MIRROR", "", "", "SMBALERT",
- "DEBUG_0", "DEBUG_1", "SDIO_SCK", "SDIO_CMD", "SDIO_D3",
- "SDIO_D2", "SDIO_D1", "SDIO_D0",
+ "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
"SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
- "SD1_DATA3", "", "",
- "", "ETH_RESET", "WIFI_PD", "WIFI_BT_RST", "ETH_INT", "",
- "WL_IRQ", "ETH_MDC";
+ "SD1_DATA3", "ETH_MDIO", "",
+ "", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
};
&gpio2 {
@@ -270,8 +268,8 @@ &gpio2 {
"YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
"", "LED_PWM", "", "", "",
"", "", "",
- "", "", "", "", "", "", "", "ON_SWITCH",
- "POWER_LED", "", "ECSPI2_SS0", "", "", "", "", "";
+ "", "", "", "", "", "ISB_IN2", "ISB_nIN1", "ON_SWITCH",
+ "POWER_LED", "", "", "", "", "", "", "";
};
&gpio3 {
@@ -280,7 +278,8 @@ &gpio3 {
"", "", "", "", "", "", "", "",
"ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
"CPU_ON1_FB", "USB_OTG_OC", "USB_OTG_PWR", "YACO_IRQ",
- "", "", "", "", "", "", "", "";
+ "TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0",
+ "YACO_RESET";
};
&gpio4 {
@@ -288,8 +287,8 @@ &gpio4 {
"", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
"UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
"CAN2_SR", "CAN2_TX", "CAN2_RX",
- "LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "", "", "", "ON1_CTRL",
- "ON2_CTRL", "HITCH_IN_OUT",
+ "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
+ "HITCH_IN_OUT",
"LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
"ISB_LED";
};
--
2.30.2
^ permalink raw reply related [flat|nested] 42+ messages in thread
* [PATCH v1 08/17] arm: dts: imx6qdl-vicut1.dtsi: Remove conflicting pinctrl entry
2022-04-12 7:39 ` Oleksij Rempel
@ 2022-04-12 7:39 ` Oleksij Rempel
-1 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
The function of DISP0_DAT9 is dependent on hardware revision of two
particular variants. This setting should be done by the bootloader anyway,
and is not needed in the kernel, so remove it from the DT.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 4 ----
1 file changed, 4 deletions(-)
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index a93e7f8302aa..6c943ca950f4 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -655,10 +655,6 @@ MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x100b0
/* DIP1_FB */
MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0
-
- /* New in UT2: FIXME: ISB PWM should start off, PD */
- /* ISB_LED_PWM */
- MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x130b0
>;
};
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 42+ messages in thread
* [PATCH v1 08/17] arm: dts: imx6qdl-vicut1.dtsi: Remove conflicting pinctrl entry
@ 2022-04-12 7:39 ` Oleksij Rempel
0 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
The function of DISP0_DAT9 is dependent on hardware revision of two
particular variants. This setting should be done by the bootloader anyway,
and is not needed in the kernel, so remove it from the DT.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 4 ----
1 file changed, 4 deletions(-)
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index a93e7f8302aa..6c943ca950f4 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -655,10 +655,6 @@ MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x100b0
/* DIP1_FB */
MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0
-
- /* New in UT2: FIXME: ISB PWM should start off, PD */
- /* ISB_LED_PWM */
- MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x130b0
>;
};
--
2.30.2
^ permalink raw reply related [flat|nested] 42+ messages in thread
* [PATCH v1 09/17] arm: dts: imx6q-vicut1.dts: remove sata node
2022-04-12 7:39 ` Oleksij Rempel
@ 2022-04-12 7:39 ` Oleksij Rempel
-1 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
Only the prototype had the SATA interface. No are no existing products
and plans to add any.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6q-vicut1.dts | 4 ----
1 file changed, 4 deletions(-)
diff --git a/arch/arm/boot/dts/imx6q-vicut1.dts b/arch/arm/boot/dts/imx6q-vicut1.dts
index 0a4e251be162..e6c5d3cb48d7 100644
--- a/arch/arm/boot/dts/imx6q-vicut1.dts
+++ b/arch/arm/boot/dts/imx6q-vicut1.dts
@@ -11,7 +11,3 @@ / {
model = "Kverneland UT1Q Board";
compatible = "kvg,vicut1q", "fsl,imx6q";
};
-
-&sata {
- status = "okay";
-};
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 42+ messages in thread* [PATCH v1 09/17] arm: dts: imx6q-vicut1.dts: remove sata node
@ 2022-04-12 7:39 ` Oleksij Rempel
0 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
Only the prototype had the SATA interface. No are no existing products
and plans to add any.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6q-vicut1.dts | 4 ----
1 file changed, 4 deletions(-)
diff --git a/arch/arm/boot/dts/imx6q-vicut1.dts b/arch/arm/boot/dts/imx6q-vicut1.dts
index 0a4e251be162..e6c5d3cb48d7 100644
--- a/arch/arm/boot/dts/imx6q-vicut1.dts
+++ b/arch/arm/boot/dts/imx6q-vicut1.dts
@@ -11,7 +11,3 @@ / {
model = "Kverneland UT1Q Board";
compatible = "kvg,vicut1q", "fsl,imx6q";
};
-
-&sata {
- status = "okay";
-};
--
2.30.2
^ permalink raw reply related [flat|nested] 42+ messages in thread* Re: [PATCH v1 09/17] arm: dts: imx6q-vicut1.dts: remove sata node
2022-04-12 7:39 ` Oleksij Rempel
@ 2022-04-18 11:53 ` Shawn Guo
-1 siblings, 0 replies; 42+ messages in thread
From: Shawn Guo @ 2022-04-18 11:53 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Rob Herring, David Jander, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
On Tue, Apr 12, 2022 at 09:39:56AM +0200, Oleksij Rempel wrote:
> From: David Jander <david@protonic.nl>
>
> Only the prototype had the SATA interface. No are no existing products
> and plans to add any.
No are?
Shawn
>
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
> arch/arm/boot/dts/imx6q-vicut1.dts | 4 ----
> 1 file changed, 4 deletions(-)
>
> diff --git a/arch/arm/boot/dts/imx6q-vicut1.dts b/arch/arm/boot/dts/imx6q-vicut1.dts
> index 0a4e251be162..e6c5d3cb48d7 100644
> --- a/arch/arm/boot/dts/imx6q-vicut1.dts
> +++ b/arch/arm/boot/dts/imx6q-vicut1.dts
> @@ -11,7 +11,3 @@ / {
> model = "Kverneland UT1Q Board";
> compatible = "kvg,vicut1q", "fsl,imx6q";
> };
> -
> -&sata {
> - status = "okay";
> -};
> --
> 2.30.2
>
^ permalink raw reply [flat|nested] 42+ messages in thread* Re: [PATCH v1 09/17] arm: dts: imx6q-vicut1.dts: remove sata node
@ 2022-04-18 11:53 ` Shawn Guo
0 siblings, 0 replies; 42+ messages in thread
From: Shawn Guo @ 2022-04-18 11:53 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Rob Herring, David Jander, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
On Tue, Apr 12, 2022 at 09:39:56AM +0200, Oleksij Rempel wrote:
> From: David Jander <david@protonic.nl>
>
> Only the prototype had the SATA interface. No are no existing products
> and plans to add any.
No are?
Shawn
>
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
> arch/arm/boot/dts/imx6q-vicut1.dts | 4 ----
> 1 file changed, 4 deletions(-)
>
> diff --git a/arch/arm/boot/dts/imx6q-vicut1.dts b/arch/arm/boot/dts/imx6q-vicut1.dts
> index 0a4e251be162..e6c5d3cb48d7 100644
> --- a/arch/arm/boot/dts/imx6q-vicut1.dts
> +++ b/arch/arm/boot/dts/imx6q-vicut1.dts
> @@ -11,7 +11,3 @@ / {
> model = "Kverneland UT1Q Board";
> compatible = "kvg,vicut1q", "fsl,imx6q";
> };
> -
> -&sata {
> - status = "okay";
> -};
> --
> 2.30.2
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 42+ messages in thread
* [PATCH v1 10/17] arm: dts: imx6dl-victgo.dts: update gpio names
2022-04-12 7:39 ` Oleksij Rempel
@ 2022-04-12 7:39 ` Oleksij Rempel
-1 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
Following changes was made:
- Add MDIO signal names
- Add missing ISB_IN2 name. Also correct ISB_nIN1. These two signals were used
together in older HW revisions. Later ISB_IN2 was removed. Software should
still be able to use both.
- Add missing CAN1 and UART line names
- Add missing ON1/2_CTRL line names
- fix CPU_* line names. The real signal names are without the CPU_ prefix, like
on imx6qdl-vicut1.dtsi
- Fix ETH_INT signal name
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-victgo.dts | 41 ++++++++++++++++++++++-------
1 file changed, 31 insertions(+), 10 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 9cf4df3eaeb0..7fc5bb499cbc 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -408,8 +408,8 @@ &gpio1 {
"CAM2_MIRROR", "", "", "SMBALERT",
"DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
"SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
- "SD1_DATA3", "", "",
- "", "", "", "", "", "", "", "";
+ "SD1_DATA3", "ETH_MDIO", "",
+ "", "", "", "", "", "", "", "ETH_MDC";
};
&gpio2 {
@@ -417,7 +417,7 @@ &gpio2 {
"YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
"", "LED_PWM", "", "", "",
"", "", "",
- "", "", "", "", "", "", "ISB_IN1", "ON_SWITCH",
+ "", "", "", "", "", "ISB_IN2", "ISB_nIN1", "ON_SWITCH",
"POWER_LED", "", "", "", "", "", "", "";
};
@@ -426,18 +426,20 @@ &gpio3 {
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
"ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
- "CPU_ON1_FB", "USB_EXT1_OC", "USB_EXT1_PWR", "YACO_IRQ",
+ "CPU_ON1_FB", "USB_OTG_OC", "USB_OTG_PWR", "YACO_IRQ",
"TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0",
"YACO_RESET";
};
&gpio4 {
gpio-line-names =
- "", "", "", "", "", "", "", "",
- "", "", "", "", "CAN1_SR", "CAN2_SR", "CAN2_TX", "CAN2_RX",
- "", "", "DIP1_FB", "", "VCAM_EN", "", "", "",
- "CPU_LIGHT_ON", "", "ETH_RESET", "CPU_CONTACT_IN", "BL_EN",
- "BL_PWM", "ETH_INTRP", "ISB_LED";
+ "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
+ "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
+ "CAN2_SR", "CAN2_TX", "CAN2_RX",
+ "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
+ "HITCH_IN_OUT",
+ "LIGHT_ON", "", "ETH_RESET", "CONTACT_IN", "BL_EN",
+ "BL_PWM", "ETH_INT", "ISB_LED";
};
&gpio5 {
@@ -445,11 +447,30 @@ &gpio5 {
"", "", "", "", "", "", "", "",
"TSC_PENIRQ", "TSC_BUSY", "ECSPI2_MOSI", "ECSPI2_MISO",
"ECSPI2_SS0", "ECSPI2_SCLK", "", "",
- "", "", "", "", "", "", "", "",
+ "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
+ "I2S_BITCLK", "I2S_DOUT",
"I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
"YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
};
+&gpio6 {
+ gpio-line-names =
+ "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
+ "ITU656_D6", "ITU656_D7", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio7 {
+ gpio-line-names =
+ "EMMC_DAT5", "EMMC_DAT4", "EMMC_CMD", "EMMC_CLK", "EMMC_DAT0",
+ "EMMC_DAT1", "EMMC_DAT2", "EMMC_DAT3",
+ "EMMC_RST", "", "", "", "CAM_DETECT", "", "", "",
+ "", "EMMC_DAT7", "EMMC_DAT6", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default";
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 42+ messages in thread* [PATCH v1 10/17] arm: dts: imx6dl-victgo.dts: update gpio names
@ 2022-04-12 7:39 ` Oleksij Rempel
0 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
Following changes was made:
- Add MDIO signal names
- Add missing ISB_IN2 name. Also correct ISB_nIN1. These two signals were used
together in older HW revisions. Later ISB_IN2 was removed. Software should
still be able to use both.
- Add missing CAN1 and UART line names
- Add missing ON1/2_CTRL line names
- fix CPU_* line names. The real signal names are without the CPU_ prefix, like
on imx6qdl-vicut1.dtsi
- Fix ETH_INT signal name
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-victgo.dts | 41 ++++++++++++++++++++++-------
1 file changed, 31 insertions(+), 10 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 9cf4df3eaeb0..7fc5bb499cbc 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -408,8 +408,8 @@ &gpio1 {
"CAM2_MIRROR", "", "", "SMBALERT",
"DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
"SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
- "SD1_DATA3", "", "",
- "", "", "", "", "", "", "", "";
+ "SD1_DATA3", "ETH_MDIO", "",
+ "", "", "", "", "", "", "", "ETH_MDC";
};
&gpio2 {
@@ -417,7 +417,7 @@ &gpio2 {
"YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
"", "LED_PWM", "", "", "",
"", "", "",
- "", "", "", "", "", "", "ISB_IN1", "ON_SWITCH",
+ "", "", "", "", "", "ISB_IN2", "ISB_nIN1", "ON_SWITCH",
"POWER_LED", "", "", "", "", "", "", "";
};
@@ -426,18 +426,20 @@ &gpio3 {
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
"ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
- "CPU_ON1_FB", "USB_EXT1_OC", "USB_EXT1_PWR", "YACO_IRQ",
+ "CPU_ON1_FB", "USB_OTG_OC", "USB_OTG_PWR", "YACO_IRQ",
"TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0",
"YACO_RESET";
};
&gpio4 {
gpio-line-names =
- "", "", "", "", "", "", "", "",
- "", "", "", "", "CAN1_SR", "CAN2_SR", "CAN2_TX", "CAN2_RX",
- "", "", "DIP1_FB", "", "VCAM_EN", "", "", "",
- "CPU_LIGHT_ON", "", "ETH_RESET", "CPU_CONTACT_IN", "BL_EN",
- "BL_PWM", "ETH_INTRP", "ISB_LED";
+ "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
+ "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
+ "CAN2_SR", "CAN2_TX", "CAN2_RX",
+ "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
+ "HITCH_IN_OUT",
+ "LIGHT_ON", "", "ETH_RESET", "CONTACT_IN", "BL_EN",
+ "BL_PWM", "ETH_INT", "ISB_LED";
};
&gpio5 {
@@ -445,11 +447,30 @@ &gpio5 {
"", "", "", "", "", "", "", "",
"TSC_PENIRQ", "TSC_BUSY", "ECSPI2_MOSI", "ECSPI2_MISO",
"ECSPI2_SS0", "ECSPI2_SCLK", "", "",
- "", "", "", "", "", "", "", "",
+ "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
+ "I2S_BITCLK", "I2S_DOUT",
"I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
"YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
};
+&gpio6 {
+ gpio-line-names =
+ "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
+ "ITU656_D6", "ITU656_D7", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio7 {
+ gpio-line-names =
+ "EMMC_DAT5", "EMMC_DAT4", "EMMC_CMD", "EMMC_CLK", "EMMC_DAT0",
+ "EMMC_DAT1", "EMMC_DAT2", "EMMC_DAT3",
+ "EMMC_RST", "", "", "", "CAM_DETECT", "", "", "",
+ "", "EMMC_DAT7", "EMMC_DAT6", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default";
--
2.30.2
^ permalink raw reply related [flat|nested] 42+ messages in thread
* [PATCH v1 11/17] arm: dts: imx6dl-victgo.dts: Factor out common parts to imx6qdl-victgo.dtsi
2022-04-12 7:39 ` Oleksij Rempel
@ 2022-04-12 7:39 ` Oleksij Rempel
-1 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
These parts are common to imx6qdl-vicut1.dtsi.
This patch is preparation to unify victgo and vicut1 DTs.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-victgo.dts | 649 +------------------------
arch/arm/boot/dts/imx6qdl-victgo.dtsi | 658 ++++++++++++++++++++++++++
2 files changed, 659 insertions(+), 648 deletions(-)
create mode 100644 arch/arm/boot/dts/imx6qdl-victgo.dtsi
diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 7fc5bb499cbc..6d61e87405f4 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -5,76 +5,13 @@
*/
/dts-v1/;
-#include <dt-bindings/display/sdtv-standards.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/media/tvp5150.h>
-#include <dt-bindings/sound/fsl-imx-audmux.h>
#include "imx6dl.dtsi"
+#include "imx6qdl-victgo.dtsi"
/ {
model = "Kverneland TGO";
compatible = "kvg,victgo", "fsl,imx6dl";
- chosen {
- stdout-path = &uart4;
- };
-
- backlight_lcd: backlight {
- compatible = "pwm-backlight";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_backlight>;
- pwms = <&pwm1 0 5000000 0>;
- brightness-levels = <0 16 64 255>;
- num-interpolated-steps = <16>;
- default-brightness-level = <48>;
- power-supply = <®_3v3>;
- enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
- };
-
- backlight_led: backlight_led {
- compatible = "pwm-backlight";
- pwms = <&pwm3 0 5000000 0>;
- brightness-levels = <0 16 64 255>;
- num-interpolated-steps = <16>;
- default-brightness-level = <48>;
- power-supply = <®_3v3>;
- };
-
- connector {
- compatible = "composite-video-connector";
- label = "Composite0";
- sdtv-standards = <SDTV_STD_PAL_B>;
-
- port {
- comp0_out: endpoint {
- remote-endpoint = <&tvp5150_comp0_in>;
- };
- };
- };
-
- counter-0 {
- compatible = "interrupt-counter";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_counter0>;
- gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
- };
-
- counter-1 {
- compatible = "interrupt-counter";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_counter1>;
- gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
- };
-
- counter-2 {
- compatible = "interrupt-counter";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_counter2>;
- gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
- };
-
gpio-keys {
compatible = "gpio-keys";
pinctrl-names = "default";
@@ -101,33 +38,6 @@ iio-hwmon {
io-channels = <&vdiv_vaccu>, <&vdiv_hitch_pos>;
};
- leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_leds>;
-
- led-0 {
- label = "debug0";
- function = LED_FUNCTION_HEARTBEAT;
- gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- };
-
- led-1 {
- label = "debug1";
- function = LED_FUNCTION_DISK;
- gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "disk-activity";
- };
-
- led-2 {
- label = "power_led";
- function = LED_FUNCTION_POWER;
- gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
- default-state = "on";
- };
- };
-
panel {
compatible = "lg,lb070wv8";
backlight = <&backlight_lcd>;
@@ -146,29 +56,6 @@ clk50m_phy: phy-clock {
clock-frequency = <50000000>;
};
- reg_1v8: regulator-1v8 {
- compatible = "regulator-fixed";
- regulator-name = "1v8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- reg_3v3: regulator-3v3 {
- compatible = "regulator-fixed";
- regulator-name = "3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- reg_otg_vbus: regulator-otg-vbus {
- compatible = "regulator-fixed";
- regulator-name = "otg-vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
rotary-encoder {
compatible = "rotary-encoder";
pinctrl-0 = <&pinctrl_rotary_ch>;
@@ -181,33 +68,6 @@ rotary-encoder {
wakeup-source;
};
- sound {
- compatible = "simple-audio-card";
- simple-audio-card,name = "prti6q-sgtl5000";
- simple-audio-card,format = "i2s";
- simple-audio-card,widgets =
- "Microphone", "Microphone Jack",
- "Line", "Line In Jack",
- "Headphone", "Headphone Jack",
- "Speaker", "External Speaker";
- simple-audio-card,routing =
- "MIC_IN", "Microphone Jack",
- "LINE_IN", "Line In Jack",
- "Headphone Jack", "HP_OUT",
- "External Speaker", "LINE_OUT";
-
- simple-audio-card,cpu {
- sound-dai = <&ssi1>;
- system-clock-frequency = <0>;
- };
-
- simple-audio-card,codec {
- sound-dai = <&codec>;
- bitclock-master;
- frame-master;
- };
- };
-
thermal-zones {
chassis-thermal {
polling-delay = <20000>;
@@ -275,63 +135,6 @@ vdiv_hitch_pos: voltage-divider-hitch-pos {
};
};
-&audmux {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_audmux>;
- status = "okay";
-
- mux-ssi1 {
- fsl,audmux-port = <0>;
- fsl,port-config = <
- IMX_AUDMUX_V2_PTCR_SYN 0
- IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
- IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
- IMX_AUDMUX_V2_PTCR_TFSDIR 0
- IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
- >;
- };
-
- mux-pins3 {
- fsl,audmux-port = <2>;
- fsl,port-config = <
- IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
- 0 IMX_AUDMUX_V2_PDCR_TXRXEN
- >;
- };
-};
-
-&can1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_can1>;
- termination-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
- termination-ohms = <150>;
- status = "okay";
-};
-
-&can2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_can2>;
- status = "okay";
-};
-
-&clks {
- assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
- assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
-};
-
-&ecspi1 {
- cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi1>;
- status = "okay";
-
- flash@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <20000000>;
- };
-};
-
&ecspi2 {
cs-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
@@ -412,25 +215,6 @@ &gpio1 {
"", "", "", "", "", "", "", "ETH_MDC";
};
-&gpio2 {
- gpio-line-names =
- "YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
- "", "LED_PWM", "", "", "",
- "", "", "",
- "", "", "", "", "", "ISB_IN2", "ISB_nIN1", "ON_SWITCH",
- "POWER_LED", "", "", "", "", "", "", "";
-};
-
-&gpio3 {
- gpio-line-names =
- "", "", "", "", "", "", "", "",
- "", "", "", "", "", "", "", "",
- "ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
- "CPU_ON1_FB", "USB_OTG_OC", "USB_OTG_PWR", "YACO_IRQ",
- "TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0",
- "YACO_RESET";
-};
-
&gpio4 {
gpio-line-names =
"", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
@@ -462,55 +246,7 @@ &gpio6 {
"", "", "", "", "", "", "", "";
};
-&gpio7 {
- gpio-line-names =
- "EMMC_DAT5", "EMMC_DAT4", "EMMC_CMD", "EMMC_CLK", "EMMC_DAT0",
- "EMMC_DAT1", "EMMC_DAT2", "EMMC_DAT3",
- "EMMC_RST", "", "", "", "CAM_DETECT", "", "", "",
- "", "EMMC_DAT7", "EMMC_DAT6", "", "", "", "", "",
- "", "", "", "", "", "", "", "";
-};
-
&i2c1 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c1>;
- status = "okay";
-
- codec: audio-codec@a {
- compatible = "fsl,sgtl5000";
- reg = <0xa>;
- #sound-dai-cells = <0>;
- clocks = <&clks 201>;
- VDDA-supply = <®_3v3>;
- VDDIO-supply = <®_3v3>;
- VDDD-supply = <®_1v8>;
- };
-
- video-decoder@5c {
- compatible = "ti,tvp5150";
- reg = <0x5c>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
-
- tvp5150_comp0_in: endpoint {
- remote-endpoint = <&comp0_out>;
- };
- };
-
- /* Output port 2 is video output pad */
- port@2 {
- reg = <2>;
-
- tvp5151_to_ipu1_csi0_mux: endpoint {
- remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
- };
- };
- };
-
keypad@70 {
compatible = "holtek,ht16k33";
pinctrl-names = "default";
@@ -534,236 +270,9 @@ MATRIX_KEY(5, 1, KEY_F3)
MATRIX_KEY(6, 1, KEY_F1)
>;
};
-
- /* additional i2c devices are added automatically by the boot loader */
-};
-
-&i2c3 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c3>;
- status = "okay";
-
- adc@49 {
- compatible = "ti,ads1015";
- reg = <0x49>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- channel@4 {
- reg = <4>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
-
- channel@5 {
- reg = <5>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
-
- channel@6 {
- reg = <6>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
-
- channel@7 {
- reg = <7>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
- };
-
- rtc@51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
-
- tsens0: temperature-sensor@70 {
- compatible = "ti,tmp103";
- reg = <0x70>;
- #thermal-sensor-cells = <0>;
- };
-};
-
-&ipu1_csi0 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ipu1_csi0>;
- status = "okay";
-};
-
-&ipu1_csi0_mux_from_parallel_sensor {
- remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
-};
-
-&ldb {
- status = "okay";
-
- lvds-channel@0 {
- status = "okay";
-
- port@4 {
- reg = <4>;
-
- lvds0_out: endpoint {
- remote-endpoint = <&panel_in>;
- };
- };
- };
-};
-
-&pwm1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm1>;
- status = "okay";
-};
-
-&pwm3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm3>;
- status = "okay";
-};
-
-&ssi1 {
- #sound-dai-cells = <0>;
- fsl,mode = "ac97-slave";
- status = "okay";
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
- status = "okay";
-};
-
-&uart3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart3>;
- status = "okay";
-};
-
-&uart4 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart4>;
- status = "okay";
-};
-
-&uart5 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart5>;
- status = "okay";
-};
-
-&usbh1 {
- pinctrl-names = "default";
- phy_type = "utmi";
- dr_mode = "host";
- status = "okay";
-};
-
-&usbotg {
- vbus-supply = <®_otg_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg>;
- phy_type = "utmi";
- dr_mode = "host";
- disable-over-current;
- status = "okay";
-};
-
-&usdhc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc1>;
- cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
- no-1-8-v;
- disable-wp;
- cap-sd-highspeed;
- no-mmc;
- no-sdio;
- status = "okay";
-};
-
-&usdhc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc3>;
- bus-width = <8>;
- no-1-8-v;
- non-removable;
- no-sd;
- no-sdio;
- status = "okay";
};
&iomuxc {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_hog>;
-
- pinctrl_audmux: audmuxgrp {
- fsl,pins = <
- /* SGTL5000 sys_mclk */
- MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
- MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
- MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
- MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
- MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
- >;
- };
-
- pinctrl_backlight: backlightgrp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
- >;
- };
-
- pinctrl_can1: can1grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000
- MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008
- /* CAN1_SR */
- MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008
- /* CAN1_TERM */
- MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b088
- >;
- };
-
- pinctrl_can2: can2grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b000
- MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x3008
- /* CAN2_SR */
- MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13008
- >;
- };
-
- pinctrl_counter0: counter0grp {
- fsl,pins = <
- MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b000
- >;
- };
-
- pinctrl_counter1: counter1grp {
- fsl,pins = <
- MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b000
- >;
- };
-
- pinctrl_counter2: counter2grp {
- fsl,pins = <
- MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b000
- >;
- };
-
- pinctrl_ecspi1: ecspi1grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
- MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
- MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
- /* CS */
- MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
- >;
- };
-
pinctrl_ecspi2: ecspi2grp {
fsl,pins = <
MX6QDL_PAD_DISP0_DAT16__ECSPI2_MOSI 0x100b1
@@ -802,102 +311,12 @@ MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
>;
};
- pinctrl_hog: hoggrp {
- fsl,pins = <
- /* ITU656_nRESET */
- MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
- /* CAM1_MIRROR */
- MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x130b0
- /* CAM2_MIRROR */
- MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x130b0
- /* CAM_nDETECT */
- MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
- /* ISB_IN1 */
- MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x130b0
- /* ISB_nIN2 */
- MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b0
- /* WARN_LIGHT */
- MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x100b0
- /* ON2_FB */
- MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b0
- /* YACO_nIRQ */
- MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b0
- /* YACO_BOOT0 */
- MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x130b0
- /* YACO_nRESET */
- MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0
- /* FORCE_ON1 */
- MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
- /* AUDIO_nRESET */
- MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0
- /* ITU656_nPDN */
- MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
-
- /* New in HW revision 1 */
- /* ON1_FB */
- MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x100b0
- /* DIP1_FB */
- MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0
- >;
- };
-
- pinctrl_i2c1: i2c1grp {
- fsl,pins = <
- MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
- MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
- >;
- };
-
- pinctrl_i2c3: i2c3grp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
- MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
- >;
- };
-
- pinctrl_ipu1_csi0: ipu1csi0grp {
- fsl,pins = <
- MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
- MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
- MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
- MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
- MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
- MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
- MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
- MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
- MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
- >;
- };
-
pinctrl_keypad: keypadgrp {
fsl,pins = <
MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0
>;
};
- pinctrl_leds: ledsgrp {
- fsl,pins = <
- /* DEBUG0 */
- MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0
- /* DEBUG1 */
- MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0
- /* POWER_LED */
- MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b0
- >;
- };
-
- pinctrl_pwm1: pwm1grp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
- >;
- };
-
- pinctrl_pwm3: pwm3grp {
- fsl,pins = <
- MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b0
- >;
- };
-
pinctrl_rotary_ch: rotarychgrp {
fsl,pins = <
MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0
@@ -911,70 +330,4 @@ MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08 0x1b0b0
MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x1b0b0
>;
};
-
- /* YaCO AUX Uart */
- pinctrl_uart1: uart1grp {
- fsl,pins = <
- MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
- MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
- >;
- };
-
- /* YaCO Touchscreen UART */
- pinctrl_uart3: uart3grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
- >;
- };
-
- pinctrl_uart4: uart4grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
- MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
- >;
- };
-
- pinctrl_uart5: uart5grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
- MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
- >;
- };
-
- pinctrl_usbotg: usbotggrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
- /* power enable, high active */
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
- >;
- };
-
- pinctrl_usdhc1: usdhc1grp {
- fsl,pins = <
- MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
- MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
- MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
- MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
- MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
- MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
- MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
- >;
- };
-
- pinctrl_usdhc3: usdhc3grp {
- fsl,pins = <
- MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
- MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
- MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
- MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
- MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
- MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
- MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
- MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
- MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
- MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
- MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
- >;
- };
};
diff --git a/arch/arm/boot/dts/imx6qdl-victgo.dtsi b/arch/arm/boot/dts/imx6qdl-victgo.dtsi
new file mode 100644
index 000000000000..386e2ca39424
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-victgo.dtsi
@@ -0,0 +1,658 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2016 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+#include <dt-bindings/display/sdtv-standards.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/media/tvp5150.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ backlight_lcd: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_backlight>;
+ pwms = <&pwm1 0 5000000 0>;
+ brightness-levels = <0 16 64 255>;
+ num-interpolated-steps = <16>;
+ default-brightness-level = <48>;
+ power-supply = <®_3v3>;
+ enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+ };
+
+ backlight_led: backlight_led {
+ compatible = "pwm-backlight";
+ pwms = <&pwm3 0 5000000 0>;
+ brightness-levels = <0 16 64 255>;
+ num-interpolated-steps = <16>;
+ default-brightness-level = <48>;
+ power-supply = <®_3v3>;
+ };
+
+ connector {
+ compatible = "composite-video-connector";
+ label = "Composite0";
+ sdtv-standards = <SDTV_STD_PAL_B>;
+
+ port {
+ comp0_out: endpoint {
+ remote-endpoint = <&tvp5150_comp0_in>;
+ };
+ };
+ };
+
+ counter-0 {
+ compatible = "interrupt-counter";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_counter0>;
+ gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+ };
+
+ counter-1 {
+ compatible = "interrupt-counter";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_counter1>;
+ gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+ };
+
+ counter-2 {
+ compatible = "interrupt-counter";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_counter2>;
+ gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-0 {
+ label = "debug0";
+ function = LED_FUNCTION_HEARTBEAT;
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led-1 {
+ label = "debug1";
+ function = LED_FUNCTION_DISK;
+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "disk-activity";
+ };
+
+ led-2 {
+ label = "power_led";
+ function = LED_FUNCTION_POWER;
+ gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ reg_1v8: regulator-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_otg_vbus: regulator-otg-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "otg-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "prti6q-sgtl5000";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Line", "Line In Jack",
+ "Headphone", "Headphone Jack",
+ "Speaker", "External Speaker";
+ simple-audio-card,routing =
+ "MIC_IN", "Microphone Jack",
+ "LINE_IN", "Line In Jack",
+ "Headphone Jack", "HP_OUT",
+ "External Speaker", "LINE_OUT";
+
+ simple-audio-card,cpu {
+ sound-dai = <&ssi1>;
+ system-clock-frequency = <0>; /* Do NOT call fsl_ssi_set_dai_sysclk! */
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&codec>;
+ bitclock-master;
+ frame-master;
+ };
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+
+ mux-ssi1 {
+ fsl,audmux-port = <0>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN 0
+ IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TFSDIR 0
+ IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+ >;
+ };
+
+ mux-pins3 {
+ fsl,audmux-port = <2>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
+ 0 IMX_AUDMUX_V2_PDCR_TXRXEN
+ >;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1>;
+ termination-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+ termination-ohms = <150>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can2>;
+ status = "okay";
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+};
+
+&gpio2 {
+ gpio-line-names =
+ "YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
+ "", "LED_PWM", "", "", "",
+ "", "", "",
+ "", "", "", "", "", "ISB_IN2", "ISB_nIN1", "ON_SWITCH",
+ "POWER_LED", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
+ "CPU_ON1_FB", "USB_OTG_OC", "USB_OTG_PWR", "YACO_IRQ",
+ "TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0",
+ "YACO_RESET";
+};
+
+&gpio7 {
+ gpio-line-names =
+ "EMMC_DAT5", "EMMC_DAT4", "EMMC_CMD", "EMMC_CLK", "EMMC_DAT0",
+ "EMMC_DAT1", "EMMC_DAT2", "EMMC_DAT3",
+ "EMMC_RST", "", "", "", "CAM_DETECT", "", "", "",
+ "", "EMMC_DAT7", "EMMC_DAT6", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ codec: audio-codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0xa>;
+ #sound-dai-cells = <0>;
+ clocks = <&clks 201>;
+ VDDA-supply = <®_3v3>;
+ VDDIO-supply = <®_3v3>;
+ VDDD-supply = <®_1v8>;
+ };
+
+ video-decoder@5c {
+ compatible = "ti,tvp5150";
+ reg = <0x5c>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tvp5150_comp0_in: endpoint {
+ remote-endpoint = <&comp0_out>;
+ };
+ };
+
+ /* Output port 2 is video output pad */
+ port@2 {
+ reg = <2>;
+
+ tvp5151_to_ipu1_csi0_mux: endpoint {
+ remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+ };
+ };
+ };
+
+ /* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ adc@49 {
+ compatible = "ti,ads1015";
+ reg = <0x49>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel@4 {
+ reg = <4>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ channel@5 {
+ reg = <5>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ channel@6 {
+ reg = <6>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ channel@7 {
+ reg = <7>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+ };
+
+ rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+
+ tsens0: temperature-sensor@70 {
+ compatible = "ti,tmp103";
+ reg = <0x70>;
+ #thermal-sensor-cells = <0>;
+ };
+};
+
+&ipu1_csi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_csi0>;
+ status = "okay";
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+ remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel@0 {
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>;
+ status = "okay";
+};
+
+&ssi1 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbh1 {
+ pinctrl-names = "default";
+ phy_type = "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ phy_type = "utmi";
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ disable-wp;
+ cap-sd-highspeed;
+ no-mmc;
+ no-sdio;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ bus-width = <8>;
+ no-1-8-v;
+ non-removable;
+ no-sd;
+ no-sdio;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ /* SGTL5000 sys_mclk */
+ MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
+ >;
+ };
+
+ pinctrl_backlight: backlightgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
+ >;
+ };
+
+ pinctrl_can1: can1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008
+ /* CAN1_SR */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008
+ /* CAN1_TERM */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b088
+ >;
+ };
+
+ pinctrl_can2: can2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b000
+ MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x3008
+ /* CAN2_SR */
+ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13008
+ >;
+ };
+
+ pinctrl_counter0: counter0grp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b000
+ >;
+ };
+
+ pinctrl_counter1: counter1grp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b000
+ >;
+ };
+
+ pinctrl_counter2: counter2grp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b000
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ /* CS */
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
+ >;
+ };
+
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* ITU656_nRESET */
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+ /* CAM1_MIRROR */
+ MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x130b0
+ /* CAM2_MIRROR */
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x130b0
+ /* CAM_nDETECT */
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
+ /* ISB_IN1 */
+ MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x130b0
+ /* ISB_nIN2 */
+ MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b0
+ /* WARN_LIGHT */
+ MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x100b0
+ /* ON2_FB */
+ MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b0
+ /* YACO_nIRQ */
+ MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b0
+ /* YACO_BOOT0 */
+ MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x130b0
+ /* YACO_nRESET */
+ MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0
+ /* FORCE_ON1 */
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
+ /* AUDIO_nRESET */
+ MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0
+ /* ITU656_nPDN */
+ MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
+
+ /* New in HW revision 1 */
+ /* ON1_FB */
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x100b0
+ /* DIP1_FB */
+ MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_ipu1_csi0: ipu1csi0grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
+ MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ /* DEBUG0 */
+ MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0
+ /* DEBUG1 */
+ MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0
+ /* POWER_LED */
+ MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b0
+ >;
+ };
+
+ /* YaCO AUX Uart */
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ /* YaCO Touchscreen UART */
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
+ /* power enable, high active */
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
+ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
+ >;
+ };
+};
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 42+ messages in thread* [PATCH v1 11/17] arm: dts: imx6dl-victgo.dts: Factor out common parts to imx6qdl-victgo.dtsi
@ 2022-04-12 7:39 ` Oleksij Rempel
0 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
These parts are common to imx6qdl-vicut1.dtsi.
This patch is preparation to unify victgo and vicut1 DTs.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-victgo.dts | 649 +------------------------
arch/arm/boot/dts/imx6qdl-victgo.dtsi | 658 ++++++++++++++++++++++++++
2 files changed, 659 insertions(+), 648 deletions(-)
create mode 100644 arch/arm/boot/dts/imx6qdl-victgo.dtsi
diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 7fc5bb499cbc..6d61e87405f4 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -5,76 +5,13 @@
*/
/dts-v1/;
-#include <dt-bindings/display/sdtv-standards.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/media/tvp5150.h>
-#include <dt-bindings/sound/fsl-imx-audmux.h>
#include "imx6dl.dtsi"
+#include "imx6qdl-victgo.dtsi"
/ {
model = "Kverneland TGO";
compatible = "kvg,victgo", "fsl,imx6dl";
- chosen {
- stdout-path = &uart4;
- };
-
- backlight_lcd: backlight {
- compatible = "pwm-backlight";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_backlight>;
- pwms = <&pwm1 0 5000000 0>;
- brightness-levels = <0 16 64 255>;
- num-interpolated-steps = <16>;
- default-brightness-level = <48>;
- power-supply = <®_3v3>;
- enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
- };
-
- backlight_led: backlight_led {
- compatible = "pwm-backlight";
- pwms = <&pwm3 0 5000000 0>;
- brightness-levels = <0 16 64 255>;
- num-interpolated-steps = <16>;
- default-brightness-level = <48>;
- power-supply = <®_3v3>;
- };
-
- connector {
- compatible = "composite-video-connector";
- label = "Composite0";
- sdtv-standards = <SDTV_STD_PAL_B>;
-
- port {
- comp0_out: endpoint {
- remote-endpoint = <&tvp5150_comp0_in>;
- };
- };
- };
-
- counter-0 {
- compatible = "interrupt-counter";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_counter0>;
- gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
- };
-
- counter-1 {
- compatible = "interrupt-counter";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_counter1>;
- gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
- };
-
- counter-2 {
- compatible = "interrupt-counter";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_counter2>;
- gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
- };
-
gpio-keys {
compatible = "gpio-keys";
pinctrl-names = "default";
@@ -101,33 +38,6 @@ iio-hwmon {
io-channels = <&vdiv_vaccu>, <&vdiv_hitch_pos>;
};
- leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_leds>;
-
- led-0 {
- label = "debug0";
- function = LED_FUNCTION_HEARTBEAT;
- gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- };
-
- led-1 {
- label = "debug1";
- function = LED_FUNCTION_DISK;
- gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "disk-activity";
- };
-
- led-2 {
- label = "power_led";
- function = LED_FUNCTION_POWER;
- gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
- default-state = "on";
- };
- };
-
panel {
compatible = "lg,lb070wv8";
backlight = <&backlight_lcd>;
@@ -146,29 +56,6 @@ clk50m_phy: phy-clock {
clock-frequency = <50000000>;
};
- reg_1v8: regulator-1v8 {
- compatible = "regulator-fixed";
- regulator-name = "1v8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- reg_3v3: regulator-3v3 {
- compatible = "regulator-fixed";
- regulator-name = "3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- reg_otg_vbus: regulator-otg-vbus {
- compatible = "regulator-fixed";
- regulator-name = "otg-vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
rotary-encoder {
compatible = "rotary-encoder";
pinctrl-0 = <&pinctrl_rotary_ch>;
@@ -181,33 +68,6 @@ rotary-encoder {
wakeup-source;
};
- sound {
- compatible = "simple-audio-card";
- simple-audio-card,name = "prti6q-sgtl5000";
- simple-audio-card,format = "i2s";
- simple-audio-card,widgets =
- "Microphone", "Microphone Jack",
- "Line", "Line In Jack",
- "Headphone", "Headphone Jack",
- "Speaker", "External Speaker";
- simple-audio-card,routing =
- "MIC_IN", "Microphone Jack",
- "LINE_IN", "Line In Jack",
- "Headphone Jack", "HP_OUT",
- "External Speaker", "LINE_OUT";
-
- simple-audio-card,cpu {
- sound-dai = <&ssi1>;
- system-clock-frequency = <0>;
- };
-
- simple-audio-card,codec {
- sound-dai = <&codec>;
- bitclock-master;
- frame-master;
- };
- };
-
thermal-zones {
chassis-thermal {
polling-delay = <20000>;
@@ -275,63 +135,6 @@ vdiv_hitch_pos: voltage-divider-hitch-pos {
};
};
-&audmux {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_audmux>;
- status = "okay";
-
- mux-ssi1 {
- fsl,audmux-port = <0>;
- fsl,port-config = <
- IMX_AUDMUX_V2_PTCR_SYN 0
- IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
- IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
- IMX_AUDMUX_V2_PTCR_TFSDIR 0
- IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
- >;
- };
-
- mux-pins3 {
- fsl,audmux-port = <2>;
- fsl,port-config = <
- IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
- 0 IMX_AUDMUX_V2_PDCR_TXRXEN
- >;
- };
-};
-
-&can1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_can1>;
- termination-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
- termination-ohms = <150>;
- status = "okay";
-};
-
-&can2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_can2>;
- status = "okay";
-};
-
-&clks {
- assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
- assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
-};
-
-&ecspi1 {
- cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi1>;
- status = "okay";
-
- flash@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <20000000>;
- };
-};
-
&ecspi2 {
cs-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
@@ -412,25 +215,6 @@ &gpio1 {
"", "", "", "", "", "", "", "ETH_MDC";
};
-&gpio2 {
- gpio-line-names =
- "YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
- "", "LED_PWM", "", "", "",
- "", "", "",
- "", "", "", "", "", "ISB_IN2", "ISB_nIN1", "ON_SWITCH",
- "POWER_LED", "", "", "", "", "", "", "";
-};
-
-&gpio3 {
- gpio-line-names =
- "", "", "", "", "", "", "", "",
- "", "", "", "", "", "", "", "",
- "ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
- "CPU_ON1_FB", "USB_OTG_OC", "USB_OTG_PWR", "YACO_IRQ",
- "TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0",
- "YACO_RESET";
-};
-
&gpio4 {
gpio-line-names =
"", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
@@ -462,55 +246,7 @@ &gpio6 {
"", "", "", "", "", "", "", "";
};
-&gpio7 {
- gpio-line-names =
- "EMMC_DAT5", "EMMC_DAT4", "EMMC_CMD", "EMMC_CLK", "EMMC_DAT0",
- "EMMC_DAT1", "EMMC_DAT2", "EMMC_DAT3",
- "EMMC_RST", "", "", "", "CAM_DETECT", "", "", "",
- "", "EMMC_DAT7", "EMMC_DAT6", "", "", "", "", "",
- "", "", "", "", "", "", "", "";
-};
-
&i2c1 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c1>;
- status = "okay";
-
- codec: audio-codec@a {
- compatible = "fsl,sgtl5000";
- reg = <0xa>;
- #sound-dai-cells = <0>;
- clocks = <&clks 201>;
- VDDA-supply = <®_3v3>;
- VDDIO-supply = <®_3v3>;
- VDDD-supply = <®_1v8>;
- };
-
- video-decoder@5c {
- compatible = "ti,tvp5150";
- reg = <0x5c>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
-
- tvp5150_comp0_in: endpoint {
- remote-endpoint = <&comp0_out>;
- };
- };
-
- /* Output port 2 is video output pad */
- port@2 {
- reg = <2>;
-
- tvp5151_to_ipu1_csi0_mux: endpoint {
- remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
- };
- };
- };
-
keypad@70 {
compatible = "holtek,ht16k33";
pinctrl-names = "default";
@@ -534,236 +270,9 @@ MATRIX_KEY(5, 1, KEY_F3)
MATRIX_KEY(6, 1, KEY_F1)
>;
};
-
- /* additional i2c devices are added automatically by the boot loader */
-};
-
-&i2c3 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c3>;
- status = "okay";
-
- adc@49 {
- compatible = "ti,ads1015";
- reg = <0x49>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- channel@4 {
- reg = <4>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
-
- channel@5 {
- reg = <5>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
-
- channel@6 {
- reg = <6>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
-
- channel@7 {
- reg = <7>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
- };
-
- rtc@51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
-
- tsens0: temperature-sensor@70 {
- compatible = "ti,tmp103";
- reg = <0x70>;
- #thermal-sensor-cells = <0>;
- };
-};
-
-&ipu1_csi0 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ipu1_csi0>;
- status = "okay";
-};
-
-&ipu1_csi0_mux_from_parallel_sensor {
- remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
-};
-
-&ldb {
- status = "okay";
-
- lvds-channel@0 {
- status = "okay";
-
- port@4 {
- reg = <4>;
-
- lvds0_out: endpoint {
- remote-endpoint = <&panel_in>;
- };
- };
- };
-};
-
-&pwm1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm1>;
- status = "okay";
-};
-
-&pwm3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm3>;
- status = "okay";
-};
-
-&ssi1 {
- #sound-dai-cells = <0>;
- fsl,mode = "ac97-slave";
- status = "okay";
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
- status = "okay";
-};
-
-&uart3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart3>;
- status = "okay";
-};
-
-&uart4 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart4>;
- status = "okay";
-};
-
-&uart5 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart5>;
- status = "okay";
-};
-
-&usbh1 {
- pinctrl-names = "default";
- phy_type = "utmi";
- dr_mode = "host";
- status = "okay";
-};
-
-&usbotg {
- vbus-supply = <®_otg_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg>;
- phy_type = "utmi";
- dr_mode = "host";
- disable-over-current;
- status = "okay";
-};
-
-&usdhc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc1>;
- cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
- no-1-8-v;
- disable-wp;
- cap-sd-highspeed;
- no-mmc;
- no-sdio;
- status = "okay";
-};
-
-&usdhc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc3>;
- bus-width = <8>;
- no-1-8-v;
- non-removable;
- no-sd;
- no-sdio;
- status = "okay";
};
&iomuxc {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_hog>;
-
- pinctrl_audmux: audmuxgrp {
- fsl,pins = <
- /* SGTL5000 sys_mclk */
- MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
- MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
- MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
- MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
- MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
- >;
- };
-
- pinctrl_backlight: backlightgrp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
- >;
- };
-
- pinctrl_can1: can1grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000
- MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008
- /* CAN1_SR */
- MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008
- /* CAN1_TERM */
- MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b088
- >;
- };
-
- pinctrl_can2: can2grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b000
- MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x3008
- /* CAN2_SR */
- MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13008
- >;
- };
-
- pinctrl_counter0: counter0grp {
- fsl,pins = <
- MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b000
- >;
- };
-
- pinctrl_counter1: counter1grp {
- fsl,pins = <
- MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b000
- >;
- };
-
- pinctrl_counter2: counter2grp {
- fsl,pins = <
- MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b000
- >;
- };
-
- pinctrl_ecspi1: ecspi1grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
- MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
- MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
- /* CS */
- MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
- >;
- };
-
pinctrl_ecspi2: ecspi2grp {
fsl,pins = <
MX6QDL_PAD_DISP0_DAT16__ECSPI2_MOSI 0x100b1
@@ -802,102 +311,12 @@ MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
>;
};
- pinctrl_hog: hoggrp {
- fsl,pins = <
- /* ITU656_nRESET */
- MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
- /* CAM1_MIRROR */
- MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x130b0
- /* CAM2_MIRROR */
- MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x130b0
- /* CAM_nDETECT */
- MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
- /* ISB_IN1 */
- MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x130b0
- /* ISB_nIN2 */
- MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b0
- /* WARN_LIGHT */
- MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x100b0
- /* ON2_FB */
- MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b0
- /* YACO_nIRQ */
- MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b0
- /* YACO_BOOT0 */
- MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x130b0
- /* YACO_nRESET */
- MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0
- /* FORCE_ON1 */
- MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
- /* AUDIO_nRESET */
- MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0
- /* ITU656_nPDN */
- MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
-
- /* New in HW revision 1 */
- /* ON1_FB */
- MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x100b0
- /* DIP1_FB */
- MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0
- >;
- };
-
- pinctrl_i2c1: i2c1grp {
- fsl,pins = <
- MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
- MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
- >;
- };
-
- pinctrl_i2c3: i2c3grp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
- MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
- >;
- };
-
- pinctrl_ipu1_csi0: ipu1csi0grp {
- fsl,pins = <
- MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
- MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
- MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
- MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
- MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
- MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
- MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
- MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
- MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
- >;
- };
-
pinctrl_keypad: keypadgrp {
fsl,pins = <
MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0
>;
};
- pinctrl_leds: ledsgrp {
- fsl,pins = <
- /* DEBUG0 */
- MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0
- /* DEBUG1 */
- MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0
- /* POWER_LED */
- MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b0
- >;
- };
-
- pinctrl_pwm1: pwm1grp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
- >;
- };
-
- pinctrl_pwm3: pwm3grp {
- fsl,pins = <
- MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b0
- >;
- };
-
pinctrl_rotary_ch: rotarychgrp {
fsl,pins = <
MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0
@@ -911,70 +330,4 @@ MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08 0x1b0b0
MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x1b0b0
>;
};
-
- /* YaCO AUX Uart */
- pinctrl_uart1: uart1grp {
- fsl,pins = <
- MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
- MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
- >;
- };
-
- /* YaCO Touchscreen UART */
- pinctrl_uart3: uart3grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
- >;
- };
-
- pinctrl_uart4: uart4grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
- MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
- >;
- };
-
- pinctrl_uart5: uart5grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
- MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
- >;
- };
-
- pinctrl_usbotg: usbotggrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
- /* power enable, high active */
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
- >;
- };
-
- pinctrl_usdhc1: usdhc1grp {
- fsl,pins = <
- MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
- MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
- MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
- MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
- MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
- MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
- MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
- >;
- };
-
- pinctrl_usdhc3: usdhc3grp {
- fsl,pins = <
- MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
- MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
- MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
- MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
- MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
- MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
- MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
- MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
- MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
- MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
- MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
- >;
- };
};
diff --git a/arch/arm/boot/dts/imx6qdl-victgo.dtsi b/arch/arm/boot/dts/imx6qdl-victgo.dtsi
new file mode 100644
index 000000000000..386e2ca39424
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-victgo.dtsi
@@ -0,0 +1,658 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2016 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+#include <dt-bindings/display/sdtv-standards.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/media/tvp5150.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ backlight_lcd: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_backlight>;
+ pwms = <&pwm1 0 5000000 0>;
+ brightness-levels = <0 16 64 255>;
+ num-interpolated-steps = <16>;
+ default-brightness-level = <48>;
+ power-supply = <®_3v3>;
+ enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+ };
+
+ backlight_led: backlight_led {
+ compatible = "pwm-backlight";
+ pwms = <&pwm3 0 5000000 0>;
+ brightness-levels = <0 16 64 255>;
+ num-interpolated-steps = <16>;
+ default-brightness-level = <48>;
+ power-supply = <®_3v3>;
+ };
+
+ connector {
+ compatible = "composite-video-connector";
+ label = "Composite0";
+ sdtv-standards = <SDTV_STD_PAL_B>;
+
+ port {
+ comp0_out: endpoint {
+ remote-endpoint = <&tvp5150_comp0_in>;
+ };
+ };
+ };
+
+ counter-0 {
+ compatible = "interrupt-counter";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_counter0>;
+ gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+ };
+
+ counter-1 {
+ compatible = "interrupt-counter";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_counter1>;
+ gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+ };
+
+ counter-2 {
+ compatible = "interrupt-counter";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_counter2>;
+ gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-0 {
+ label = "debug0";
+ function = LED_FUNCTION_HEARTBEAT;
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led-1 {
+ label = "debug1";
+ function = LED_FUNCTION_DISK;
+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "disk-activity";
+ };
+
+ led-2 {
+ label = "power_led";
+ function = LED_FUNCTION_POWER;
+ gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ reg_1v8: regulator-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_otg_vbus: regulator-otg-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "otg-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "prti6q-sgtl5000";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Line", "Line In Jack",
+ "Headphone", "Headphone Jack",
+ "Speaker", "External Speaker";
+ simple-audio-card,routing =
+ "MIC_IN", "Microphone Jack",
+ "LINE_IN", "Line In Jack",
+ "Headphone Jack", "HP_OUT",
+ "External Speaker", "LINE_OUT";
+
+ simple-audio-card,cpu {
+ sound-dai = <&ssi1>;
+ system-clock-frequency = <0>; /* Do NOT call fsl_ssi_set_dai_sysclk! */
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&codec>;
+ bitclock-master;
+ frame-master;
+ };
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+
+ mux-ssi1 {
+ fsl,audmux-port = <0>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN 0
+ IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TFSDIR 0
+ IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+ >;
+ };
+
+ mux-pins3 {
+ fsl,audmux-port = <2>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
+ 0 IMX_AUDMUX_V2_PDCR_TXRXEN
+ >;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1>;
+ termination-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+ termination-ohms = <150>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can2>;
+ status = "okay";
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+};
+
+&gpio2 {
+ gpio-line-names =
+ "YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
+ "", "LED_PWM", "", "", "",
+ "", "", "",
+ "", "", "", "", "", "ISB_IN2", "ISB_nIN1", "ON_SWITCH",
+ "POWER_LED", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
+ "CPU_ON1_FB", "USB_OTG_OC", "USB_OTG_PWR", "YACO_IRQ",
+ "TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0",
+ "YACO_RESET";
+};
+
+&gpio7 {
+ gpio-line-names =
+ "EMMC_DAT5", "EMMC_DAT4", "EMMC_CMD", "EMMC_CLK", "EMMC_DAT0",
+ "EMMC_DAT1", "EMMC_DAT2", "EMMC_DAT3",
+ "EMMC_RST", "", "", "", "CAM_DETECT", "", "", "",
+ "", "EMMC_DAT7", "EMMC_DAT6", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ codec: audio-codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0xa>;
+ #sound-dai-cells = <0>;
+ clocks = <&clks 201>;
+ VDDA-supply = <®_3v3>;
+ VDDIO-supply = <®_3v3>;
+ VDDD-supply = <®_1v8>;
+ };
+
+ video-decoder@5c {
+ compatible = "ti,tvp5150";
+ reg = <0x5c>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tvp5150_comp0_in: endpoint {
+ remote-endpoint = <&comp0_out>;
+ };
+ };
+
+ /* Output port 2 is video output pad */
+ port@2 {
+ reg = <2>;
+
+ tvp5151_to_ipu1_csi0_mux: endpoint {
+ remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+ };
+ };
+ };
+
+ /* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ adc@49 {
+ compatible = "ti,ads1015";
+ reg = <0x49>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel@4 {
+ reg = <4>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ channel@5 {
+ reg = <5>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ channel@6 {
+ reg = <6>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ channel@7 {
+ reg = <7>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+ };
+
+ rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+
+ tsens0: temperature-sensor@70 {
+ compatible = "ti,tmp103";
+ reg = <0x70>;
+ #thermal-sensor-cells = <0>;
+ };
+};
+
+&ipu1_csi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_csi0>;
+ status = "okay";
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+ remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel@0 {
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>;
+ status = "okay";
+};
+
+&ssi1 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbh1 {
+ pinctrl-names = "default";
+ phy_type = "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ phy_type = "utmi";
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ disable-wp;
+ cap-sd-highspeed;
+ no-mmc;
+ no-sdio;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ bus-width = <8>;
+ no-1-8-v;
+ non-removable;
+ no-sd;
+ no-sdio;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ /* SGTL5000 sys_mclk */
+ MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
+ >;
+ };
+
+ pinctrl_backlight: backlightgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
+ >;
+ };
+
+ pinctrl_can1: can1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008
+ /* CAN1_SR */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008
+ /* CAN1_TERM */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b088
+ >;
+ };
+
+ pinctrl_can2: can2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b000
+ MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x3008
+ /* CAN2_SR */
+ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13008
+ >;
+ };
+
+ pinctrl_counter0: counter0grp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b000
+ >;
+ };
+
+ pinctrl_counter1: counter1grp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b000
+ >;
+ };
+
+ pinctrl_counter2: counter2grp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b000
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ /* CS */
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
+ >;
+ };
+
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* ITU656_nRESET */
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+ /* CAM1_MIRROR */
+ MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x130b0
+ /* CAM2_MIRROR */
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x130b0
+ /* CAM_nDETECT */
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
+ /* ISB_IN1 */
+ MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x130b0
+ /* ISB_nIN2 */
+ MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b0
+ /* WARN_LIGHT */
+ MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x100b0
+ /* ON2_FB */
+ MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b0
+ /* YACO_nIRQ */
+ MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b0
+ /* YACO_BOOT0 */
+ MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x130b0
+ /* YACO_nRESET */
+ MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0
+ /* FORCE_ON1 */
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
+ /* AUDIO_nRESET */
+ MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0
+ /* ITU656_nPDN */
+ MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
+
+ /* New in HW revision 1 */
+ /* ON1_FB */
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x100b0
+ /* DIP1_FB */
+ MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_ipu1_csi0: ipu1csi0grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
+ MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ /* DEBUG0 */
+ MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0
+ /* DEBUG1 */
+ MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0
+ /* POWER_LED */
+ MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b0
+ >;
+ };
+
+ /* YaCO AUX Uart */
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ /* YaCO Touchscreen UART */
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
+ /* power enable, high active */
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
+ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
+ >;
+ };
+};
--
2.30.2
^ permalink raw reply related [flat|nested] 42+ messages in thread
* [PATCH v1 12/17] arm: dts: imx6qdl-vicut1.dtsi: Move some node out to DTS files
2022-04-12 7:39 ` Oleksij Rempel
@ 2022-04-12 7:39 ` Oleksij Rempel
-1 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
This commit will finally make this file identical to imx6qdl-victgo.dtsi.
All nodes that are removed here are added as-is to the DTS files that
include this file.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-vicut1.dts | 122 ++++++++++++++++++++++++++
arch/arm/boot/dts/imx6q-vicut1.dts | 122 ++++++++++++++++++++++++++
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 120 -------------------------
arch/arm/boot/dts/imx6qp-vicutp.dts | 122 ++++++++++++++++++++++++++
4 files changed, 366 insertions(+), 120 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-vicut1.dts b/arch/arm/boot/dts/imx6dl-vicut1.dts
index 174fd913bf96..c6a904bbed01 100644
--- a/arch/arm/boot/dts/imx6dl-vicut1.dts
+++ b/arch/arm/boot/dts/imx6dl-vicut1.dts
@@ -10,4 +10,126 @@
/ {
model = "Kverneland UT1 Board";
compatible = "kvg,vicut1", "fsl,imx6dl";
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiokeys>;
+ autorepeat;
+
+ power {
+ label = "Power Button";
+ gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+ panel {
+ compatible = "kyo,tcg121xglp";
+ backlight = <&backlight_lcd>;
+ power-supply = <®_3v3>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ9031RNX PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&gpio1 {
+ gpio-line-names =
+ "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
+ "CAM2_MIRROR", "", "", "SMBALERT",
+ "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+ "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
+ "SD1_DATA3", "ETH_MDIO", "",
+ "", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
+ "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
+ "CAN2_SR", "CAN2_TX", "CAN2_RX",
+ "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
+ "HITCH_IN_OUT",
+ "LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
+ "ISB_LED";
+};
+
+&gpio5 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
+ "I2S_BITCLK", "I2S_DOUT",
+ "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
+ "YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
+};
+
+&gpio6 {
+ gpio-line-names =
+ "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
+ "ITU656_D6", "ITU656_D7", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
+ "RGMII_TD3",
+ "RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
+ "RGMII_RD2", "RGMII_RD3", "", "";
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+ /* Phy reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
+ >;
+ };
+
+ pinctrl_gpiokeys: gpiokeygrp {
+ fsl,pins = <
+ /* nON_SWITCH */
+ MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
+ >;
+ };
};
diff --git a/arch/arm/boot/dts/imx6q-vicut1.dts b/arch/arm/boot/dts/imx6q-vicut1.dts
index e6c5d3cb48d7..8b228d5fc4a3 100644
--- a/arch/arm/boot/dts/imx6q-vicut1.dts
+++ b/arch/arm/boot/dts/imx6q-vicut1.dts
@@ -10,4 +10,126 @@
/ {
model = "Kverneland UT1Q Board";
compatible = "kvg,vicut1q", "fsl,imx6q";
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiokeys>;
+ autorepeat;
+
+ power {
+ label = "Power Button";
+ gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+ panel {
+ compatible = "kyo,tcg121xglp";
+ backlight = <&backlight_lcd>;
+ power-supply = <®_3v3>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ9031RNX PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&gpio1 {
+ gpio-line-names =
+ "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
+ "CAM2_MIRROR", "", "", "SMBALERT",
+ "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+ "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
+ "SD1_DATA3", "ETH_MDIO", "",
+ "", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
+ "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
+ "CAN2_SR", "CAN2_TX", "CAN2_RX",
+ "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
+ "HITCH_IN_OUT",
+ "LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
+ "ISB_LED";
+};
+
+&gpio5 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
+ "I2S_BITCLK", "I2S_DOUT",
+ "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
+ "YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
+};
+
+&gpio6 {
+ gpio-line-names =
+ "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
+ "ITU656_D6", "ITU656_D7", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
+ "RGMII_TD3",
+ "RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
+ "RGMII_RD2", "RGMII_RD3", "", "";
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+ /* Phy reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
+ >;
+ };
+
+ pinctrl_gpiokeys: gpiokeygrp {
+ fsl,pins = <
+ /* nON_SWITCH */
+ MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
+ >;
+ };
};
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index 6c943ca950f4..2a86136a04e8 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -70,20 +70,6 @@ counter-2 {
gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
};
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpiokeys>;
- autorepeat;
-
- power {
- label = "Power Button";
- gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_POWER>;
- wakeup-source;
- };
- };
-
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
@@ -111,18 +97,6 @@ led-2 {
};
};
- panel {
- compatible = "kyo,tcg121xglp";
- backlight = <&backlight_lcd>;
- power-supply = <®_3v3>;
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&lvds0_out>;
- };
- };
- };
-
reg_1v8: regulator-1v8 {
compatible = "regulator-fixed";
regulator-name = "1v8";
@@ -231,38 +205,6 @@ flash@0 {
};
};
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rgmii-id";
- phy-handle = <&rgmii_phy>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* Microchip KSZ9031RNX PHY */
- rgmii_phy: ethernet-phy@0 {
- reg = <0>;
- interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
- reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
- reset-assert-us = <10000>;
- reset-deassert-us = <300>;
- };
- };
-};
-
-&gpio1 {
- gpio-line-names =
- "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
- "CAM2_MIRROR", "", "", "SMBALERT",
- "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
- "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
- "SD1_DATA3", "ETH_MDIO", "",
- "", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
-};
-
&gpio2 {
gpio-line-names =
"YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
@@ -282,38 +224,6 @@ &gpio3 {
"YACO_RESET";
};
-&gpio4 {
- gpio-line-names =
- "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
- "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
- "CAN2_SR", "CAN2_TX", "CAN2_RX",
- "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
- "HITCH_IN_OUT",
- "LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
- "ISB_LED";
-};
-
-&gpio5 {
- gpio-line-names =
- "", "", "", "", "", "", "", "",
- "", "", "", "", "", "", "", "",
- "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
- "I2S_BITCLK", "I2S_DOUT",
- "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
- "YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
-};
-
-&gpio6 {
- gpio-line-names =
- "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
- "ITU656_D6", "ITU656_D7", "", "",
- "", "", "", "", "", "", "", "",
- "", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
- "RGMII_TD3",
- "RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
- "RGMII_RD2", "RGMII_RD3", "", "";
-};
-
&gpio7 {
gpio-line-names =
"EMMC_DAT5", "EMMC_DAT4", "EMMC_CMD", "EMMC_CLK", "EMMC_DAT0",
@@ -589,36 +499,6 @@ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
>;
};
- pinctrl_enet: enetgrp {
- fsl,pins = <
- MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
- MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
- MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
- MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
- MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
- MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
- MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
- MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
- MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
- MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
- MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
- MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
- MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
- /* Phy reset */
- MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
- MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
- >;
- };
-
- pinctrl_gpiokeys: gpiokeygrp {
- fsl,pins = <
- /* nON_SWITCH */
- MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
- >;
- };
-
pinctrl_hog: hoggrp {
fsl,pins = <
/* ITU656_nRESET */
diff --git a/arch/arm/boot/dts/imx6qp-vicutp.dts b/arch/arm/boot/dts/imx6qp-vicutp.dts
index 7bad7ca6b12e..31c748e9d92f 100644
--- a/arch/arm/boot/dts/imx6qp-vicutp.dts
+++ b/arch/arm/boot/dts/imx6qp-vicutp.dts
@@ -10,4 +10,126 @@
/ {
model = "Kverneland UT1P Board";
compatible = "kvg,vicutp", "fsl,imx6qp";
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiokeys>;
+ autorepeat;
+
+ power {
+ label = "Power Button";
+ gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+ panel {
+ compatible = "kyo,tcg121xglp";
+ backlight = <&backlight_lcd>;
+ power-supply = <®_3v3>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ9031RNX PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&gpio1 {
+ gpio-line-names =
+ "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
+ "CAM2_MIRROR", "", "", "SMBALERT",
+ "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+ "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
+ "SD1_DATA3", "ETH_MDIO", "",
+ "", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
+ "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
+ "CAN2_SR", "CAN2_TX", "CAN2_RX",
+ "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
+ "HITCH_IN_OUT",
+ "LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
+ "ISB_LED";
+};
+
+&gpio5 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
+ "I2S_BITCLK", "I2S_DOUT",
+ "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
+ "YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
+};
+
+&gpio6 {
+ gpio-line-names =
+ "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
+ "ITU656_D6", "ITU656_D7", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
+ "RGMII_TD3",
+ "RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
+ "RGMII_RD2", "RGMII_RD3", "", "";
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+ /* Phy reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
+ >;
+ };
+
+ pinctrl_gpiokeys: gpiokeygrp {
+ fsl,pins = <
+ /* nON_SWITCH */
+ MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
+ >;
+ };
};
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 42+ messages in thread* [PATCH v1 12/17] arm: dts: imx6qdl-vicut1.dtsi: Move some node out to DTS files
@ 2022-04-12 7:39 ` Oleksij Rempel
0 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:39 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
This commit will finally make this file identical to imx6qdl-victgo.dtsi.
All nodes that are removed here are added as-is to the DTS files that
include this file.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-vicut1.dts | 122 ++++++++++++++++++++++++++
arch/arm/boot/dts/imx6q-vicut1.dts | 122 ++++++++++++++++++++++++++
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 120 -------------------------
arch/arm/boot/dts/imx6qp-vicutp.dts | 122 ++++++++++++++++++++++++++
4 files changed, 366 insertions(+), 120 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-vicut1.dts b/arch/arm/boot/dts/imx6dl-vicut1.dts
index 174fd913bf96..c6a904bbed01 100644
--- a/arch/arm/boot/dts/imx6dl-vicut1.dts
+++ b/arch/arm/boot/dts/imx6dl-vicut1.dts
@@ -10,4 +10,126 @@
/ {
model = "Kverneland UT1 Board";
compatible = "kvg,vicut1", "fsl,imx6dl";
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiokeys>;
+ autorepeat;
+
+ power {
+ label = "Power Button";
+ gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+ panel {
+ compatible = "kyo,tcg121xglp";
+ backlight = <&backlight_lcd>;
+ power-supply = <®_3v3>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ9031RNX PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&gpio1 {
+ gpio-line-names =
+ "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
+ "CAM2_MIRROR", "", "", "SMBALERT",
+ "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+ "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
+ "SD1_DATA3", "ETH_MDIO", "",
+ "", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
+ "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
+ "CAN2_SR", "CAN2_TX", "CAN2_RX",
+ "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
+ "HITCH_IN_OUT",
+ "LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
+ "ISB_LED";
+};
+
+&gpio5 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
+ "I2S_BITCLK", "I2S_DOUT",
+ "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
+ "YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
+};
+
+&gpio6 {
+ gpio-line-names =
+ "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
+ "ITU656_D6", "ITU656_D7", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
+ "RGMII_TD3",
+ "RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
+ "RGMII_RD2", "RGMII_RD3", "", "";
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+ /* Phy reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
+ >;
+ };
+
+ pinctrl_gpiokeys: gpiokeygrp {
+ fsl,pins = <
+ /* nON_SWITCH */
+ MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
+ >;
+ };
};
diff --git a/arch/arm/boot/dts/imx6q-vicut1.dts b/arch/arm/boot/dts/imx6q-vicut1.dts
index e6c5d3cb48d7..8b228d5fc4a3 100644
--- a/arch/arm/boot/dts/imx6q-vicut1.dts
+++ b/arch/arm/boot/dts/imx6q-vicut1.dts
@@ -10,4 +10,126 @@
/ {
model = "Kverneland UT1Q Board";
compatible = "kvg,vicut1q", "fsl,imx6q";
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiokeys>;
+ autorepeat;
+
+ power {
+ label = "Power Button";
+ gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+ panel {
+ compatible = "kyo,tcg121xglp";
+ backlight = <&backlight_lcd>;
+ power-supply = <®_3v3>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ9031RNX PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&gpio1 {
+ gpio-line-names =
+ "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
+ "CAM2_MIRROR", "", "", "SMBALERT",
+ "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+ "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
+ "SD1_DATA3", "ETH_MDIO", "",
+ "", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
+ "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
+ "CAN2_SR", "CAN2_TX", "CAN2_RX",
+ "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
+ "HITCH_IN_OUT",
+ "LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
+ "ISB_LED";
+};
+
+&gpio5 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
+ "I2S_BITCLK", "I2S_DOUT",
+ "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
+ "YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
+};
+
+&gpio6 {
+ gpio-line-names =
+ "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
+ "ITU656_D6", "ITU656_D7", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
+ "RGMII_TD3",
+ "RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
+ "RGMII_RD2", "RGMII_RD3", "", "";
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+ /* Phy reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
+ >;
+ };
+
+ pinctrl_gpiokeys: gpiokeygrp {
+ fsl,pins = <
+ /* nON_SWITCH */
+ MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
+ >;
+ };
};
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index 6c943ca950f4..2a86136a04e8 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -70,20 +70,6 @@ counter-2 {
gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
};
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpiokeys>;
- autorepeat;
-
- power {
- label = "Power Button";
- gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_POWER>;
- wakeup-source;
- };
- };
-
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
@@ -111,18 +97,6 @@ led-2 {
};
};
- panel {
- compatible = "kyo,tcg121xglp";
- backlight = <&backlight_lcd>;
- power-supply = <®_3v3>;
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&lvds0_out>;
- };
- };
- };
-
reg_1v8: regulator-1v8 {
compatible = "regulator-fixed";
regulator-name = "1v8";
@@ -231,38 +205,6 @@ flash@0 {
};
};
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rgmii-id";
- phy-handle = <&rgmii_phy>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* Microchip KSZ9031RNX PHY */
- rgmii_phy: ethernet-phy@0 {
- reg = <0>;
- interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
- reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
- reset-assert-us = <10000>;
- reset-deassert-us = <300>;
- };
- };
-};
-
-&gpio1 {
- gpio-line-names =
- "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
- "CAM2_MIRROR", "", "", "SMBALERT",
- "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
- "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
- "SD1_DATA3", "ETH_MDIO", "",
- "", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
-};
-
&gpio2 {
gpio-line-names =
"YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
@@ -282,38 +224,6 @@ &gpio3 {
"YACO_RESET";
};
-&gpio4 {
- gpio-line-names =
- "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
- "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
- "CAN2_SR", "CAN2_TX", "CAN2_RX",
- "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
- "HITCH_IN_OUT",
- "LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
- "ISB_LED";
-};
-
-&gpio5 {
- gpio-line-names =
- "", "", "", "", "", "", "", "",
- "", "", "", "", "", "", "", "",
- "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
- "I2S_BITCLK", "I2S_DOUT",
- "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
- "YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
-};
-
-&gpio6 {
- gpio-line-names =
- "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
- "ITU656_D6", "ITU656_D7", "", "",
- "", "", "", "", "", "", "", "",
- "", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
- "RGMII_TD3",
- "RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
- "RGMII_RD2", "RGMII_RD3", "", "";
-};
-
&gpio7 {
gpio-line-names =
"EMMC_DAT5", "EMMC_DAT4", "EMMC_CMD", "EMMC_CLK", "EMMC_DAT0",
@@ -589,36 +499,6 @@ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
>;
};
- pinctrl_enet: enetgrp {
- fsl,pins = <
- MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
- MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
- MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
- MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
- MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
- MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
- MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
- MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
- MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
- MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
- MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
- MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
- MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
- /* Phy reset */
- MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
- MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
- >;
- };
-
- pinctrl_gpiokeys: gpiokeygrp {
- fsl,pins = <
- /* nON_SWITCH */
- MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
- >;
- };
-
pinctrl_hog: hoggrp {
fsl,pins = <
/* ITU656_nRESET */
diff --git a/arch/arm/boot/dts/imx6qp-vicutp.dts b/arch/arm/boot/dts/imx6qp-vicutp.dts
index 7bad7ca6b12e..31c748e9d92f 100644
--- a/arch/arm/boot/dts/imx6qp-vicutp.dts
+++ b/arch/arm/boot/dts/imx6qp-vicutp.dts
@@ -10,4 +10,126 @@
/ {
model = "Kverneland UT1P Board";
compatible = "kvg,vicutp", "fsl,imx6qp";
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiokeys>;
+ autorepeat;
+
+ power {
+ label = "Power Button";
+ gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+ panel {
+ compatible = "kyo,tcg121xglp";
+ backlight = <&backlight_lcd>;
+ power-supply = <®_3v3>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ9031RNX PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&gpio1 {
+ gpio-line-names =
+ "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
+ "CAM2_MIRROR", "", "", "SMBALERT",
+ "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+ "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
+ "SD1_DATA3", "ETH_MDIO", "",
+ "", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
+ "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
+ "CAN2_SR", "CAN2_TX", "CAN2_RX",
+ "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
+ "HITCH_IN_OUT",
+ "LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
+ "ISB_LED";
+};
+
+&gpio5 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
+ "I2S_BITCLK", "I2S_DOUT",
+ "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
+ "YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
+};
+
+&gpio6 {
+ gpio-line-names =
+ "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
+ "ITU656_D6", "ITU656_D7", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
+ "RGMII_TD3",
+ "RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
+ "RGMII_RD2", "RGMII_RD3", "", "";
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+ /* Phy reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
+ >;
+ };
+
+ pinctrl_gpiokeys: gpiokeygrp {
+ fsl,pins = <
+ /* nON_SWITCH */
+ MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
+ >;
+ };
};
--
2.30.2
^ permalink raw reply related [flat|nested] 42+ messages in thread
* [PATCH v1 13/17] arm: dts: Remove imx6qdl-victgo.dtsi
2022-04-12 7:39 ` Oleksij Rempel
@ 2022-04-12 7:40 ` Oleksij Rempel
-1 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:40 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
The common base is now identical to imx6qdl-vicut1.dtsi, so we can remove
one of both.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-victgo.dts | 2 +-
arch/arm/boot/dts/imx6qdl-victgo.dtsi | 658 --------------------------
2 files changed, 1 insertion(+), 659 deletions(-)
delete mode 100644 arch/arm/boot/dts/imx6qdl-victgo.dtsi
diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 6d61e87405f4..4f6100b2ce2d 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -6,7 +6,7 @@
/dts-v1/;
#include "imx6dl.dtsi"
-#include "imx6qdl-victgo.dtsi"
+#include "imx6qdl-vicut1.dtsi"
/ {
model = "Kverneland TGO";
diff --git a/arch/arm/boot/dts/imx6qdl-victgo.dtsi b/arch/arm/boot/dts/imx6qdl-victgo.dtsi
deleted file mode 100644
index 386e2ca39424..000000000000
--- a/arch/arm/boot/dts/imx6qdl-victgo.dtsi
+++ /dev/null
@@ -1,658 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-/*
- * Copyright (c) 2016 Protonic Holland
- * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
- */
-
-#include <dt-bindings/display/sdtv-standards.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/media/tvp5150.h>
-#include <dt-bindings/sound/fsl-imx-audmux.h>
-
-/ {
- chosen {
- stdout-path = &uart4;
- };
-
- backlight_lcd: backlight {
- compatible = "pwm-backlight";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_backlight>;
- pwms = <&pwm1 0 5000000 0>;
- brightness-levels = <0 16 64 255>;
- num-interpolated-steps = <16>;
- default-brightness-level = <48>;
- power-supply = <®_3v3>;
- enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
- };
-
- backlight_led: backlight_led {
- compatible = "pwm-backlight";
- pwms = <&pwm3 0 5000000 0>;
- brightness-levels = <0 16 64 255>;
- num-interpolated-steps = <16>;
- default-brightness-level = <48>;
- power-supply = <®_3v3>;
- };
-
- connector {
- compatible = "composite-video-connector";
- label = "Composite0";
- sdtv-standards = <SDTV_STD_PAL_B>;
-
- port {
- comp0_out: endpoint {
- remote-endpoint = <&tvp5150_comp0_in>;
- };
- };
- };
-
- counter-0 {
- compatible = "interrupt-counter";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_counter0>;
- gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
- };
-
- counter-1 {
- compatible = "interrupt-counter";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_counter1>;
- gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
- };
-
- counter-2 {
- compatible = "interrupt-counter";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_counter2>;
- gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_leds>;
-
- led-0 {
- label = "debug0";
- function = LED_FUNCTION_HEARTBEAT;
- gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- };
-
- led-1 {
- label = "debug1";
- function = LED_FUNCTION_DISK;
- gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "disk-activity";
- };
-
- led-2 {
- label = "power_led";
- function = LED_FUNCTION_POWER;
- gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
- default-state = "on";
- };
- };
-
- reg_1v8: regulator-1v8 {
- compatible = "regulator-fixed";
- regulator-name = "1v8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- reg_3v3: regulator-3v3 {
- compatible = "regulator-fixed";
- regulator-name = "3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- reg_otg_vbus: regulator-otg-vbus {
- compatible = "regulator-fixed";
- regulator-name = "otg-vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- sound {
- compatible = "simple-audio-card";
- simple-audio-card,name = "prti6q-sgtl5000";
- simple-audio-card,format = "i2s";
- simple-audio-card,widgets =
- "Microphone", "Microphone Jack",
- "Line", "Line In Jack",
- "Headphone", "Headphone Jack",
- "Speaker", "External Speaker";
- simple-audio-card,routing =
- "MIC_IN", "Microphone Jack",
- "LINE_IN", "Line In Jack",
- "Headphone Jack", "HP_OUT",
- "External Speaker", "LINE_OUT";
-
- simple-audio-card,cpu {
- sound-dai = <&ssi1>;
- system-clock-frequency = <0>; /* Do NOT call fsl_ssi_set_dai_sysclk! */
- };
-
- simple-audio-card,codec {
- sound-dai = <&codec>;
- bitclock-master;
- frame-master;
- };
- };
-};
-
-&audmux {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_audmux>;
- status = "okay";
-
- mux-ssi1 {
- fsl,audmux-port = <0>;
- fsl,port-config = <
- IMX_AUDMUX_V2_PTCR_SYN 0
- IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
- IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
- IMX_AUDMUX_V2_PTCR_TFSDIR 0
- IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
- >;
- };
-
- mux-pins3 {
- fsl,audmux-port = <2>;
- fsl,port-config = <
- IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
- 0 IMX_AUDMUX_V2_PDCR_TXRXEN
- >;
- };
-};
-
-&can1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_can1>;
- termination-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
- termination-ohms = <150>;
- status = "okay";
-};
-
-&can2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_can2>;
- status = "okay";
-};
-
-&clks {
- assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
- assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
-};
-
-&ecspi1 {
- cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi1>;
- status = "okay";
-
- flash@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <20000000>;
- };
-};
-
-&gpio2 {
- gpio-line-names =
- "YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
- "", "LED_PWM", "", "", "",
- "", "", "",
- "", "", "", "", "", "ISB_IN2", "ISB_nIN1", "ON_SWITCH",
- "POWER_LED", "", "", "", "", "", "", "";
-};
-
-&gpio3 {
- gpio-line-names =
- "", "", "", "", "", "", "", "",
- "", "", "", "", "", "", "", "",
- "ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
- "CPU_ON1_FB", "USB_OTG_OC", "USB_OTG_PWR", "YACO_IRQ",
- "TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0",
- "YACO_RESET";
-};
-
-&gpio7 {
- gpio-line-names =
- "EMMC_DAT5", "EMMC_DAT4", "EMMC_CMD", "EMMC_CLK", "EMMC_DAT0",
- "EMMC_DAT1", "EMMC_DAT2", "EMMC_DAT3",
- "EMMC_RST", "", "", "", "CAM_DETECT", "", "", "",
- "", "EMMC_DAT7", "EMMC_DAT6", "", "", "", "", "",
- "", "", "", "", "", "", "", "";
-};
-
-&i2c1 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c1>;
- status = "okay";
-
- codec: audio-codec@a {
- compatible = "fsl,sgtl5000";
- reg = <0xa>;
- #sound-dai-cells = <0>;
- clocks = <&clks 201>;
- VDDA-supply = <®_3v3>;
- VDDIO-supply = <®_3v3>;
- VDDD-supply = <®_1v8>;
- };
-
- video-decoder@5c {
- compatible = "ti,tvp5150";
- reg = <0x5c>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
-
- tvp5150_comp0_in: endpoint {
- remote-endpoint = <&comp0_out>;
- };
- };
-
- /* Output port 2 is video output pad */
- port@2 {
- reg = <2>;
-
- tvp5151_to_ipu1_csi0_mux: endpoint {
- remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
- };
- };
- };
-
- /* additional i2c devices are added automatically by the boot loader */
-};
-
-&i2c3 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c3>;
- status = "okay";
-
- adc@49 {
- compatible = "ti,ads1015";
- reg = <0x49>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- channel@4 {
- reg = <4>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
-
- channel@5 {
- reg = <5>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
-
- channel@6 {
- reg = <6>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
-
- channel@7 {
- reg = <7>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
- };
-
- rtc@51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
-
- tsens0: temperature-sensor@70 {
- compatible = "ti,tmp103";
- reg = <0x70>;
- #thermal-sensor-cells = <0>;
- };
-};
-
-&ipu1_csi0 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ipu1_csi0>;
- status = "okay";
-};
-
-&ipu1_csi0_mux_from_parallel_sensor {
- remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
-};
-
-&ldb {
- status = "okay";
-
- lvds-channel@0 {
- status = "okay";
-
- port@4 {
- reg = <4>;
-
- lvds0_out: endpoint {
- remote-endpoint = <&panel_in>;
- };
- };
- };
-};
-
-&pwm1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm1>;
- status = "okay";
-};
-
-&pwm3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm3>;
- status = "okay";
-};
-
-&ssi1 {
- status = "okay";
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
- status = "okay";
-};
-
-&uart3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart3>;
- status = "okay";
-};
-
-&uart4 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart4>;
- status = "okay";
-};
-
-&uart5 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart5>;
- status = "okay";
-};
-
-&usbh1 {
- pinctrl-names = "default";
- phy_type = "utmi";
- dr_mode = "host";
- status = "okay";
-};
-
-&usbotg {
- vbus-supply = <®_otg_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg>;
- phy_type = "utmi";
- dr_mode = "host";
- disable-over-current;
- status = "okay";
-};
-
-&usdhc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc1>;
- cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
- no-1-8-v;
- disable-wp;
- cap-sd-highspeed;
- no-mmc;
- no-sdio;
- status = "okay";
-};
-
-&usdhc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc3>;
- bus-width = <8>;
- no-1-8-v;
- non-removable;
- no-sd;
- no-sdio;
- status = "okay";
-};
-
-&iomuxc {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_hog>;
-
- pinctrl_audmux: audmuxgrp {
- fsl,pins = <
- /* SGTL5000 sys_mclk */
- MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
- MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
- MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
- MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
- MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
- >;
- };
-
- pinctrl_backlight: backlightgrp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
- >;
- };
-
- pinctrl_can1: can1grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000
- MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008
- /* CAN1_SR */
- MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008
- /* CAN1_TERM */
- MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b088
- >;
- };
-
- pinctrl_can2: can2grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b000
- MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x3008
- /* CAN2_SR */
- MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13008
- >;
- };
-
- pinctrl_counter0: counter0grp {
- fsl,pins = <
- MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b000
- >;
- };
-
- pinctrl_counter1: counter1grp {
- fsl,pins = <
- MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b000
- >;
- };
-
- pinctrl_counter2: counter2grp {
- fsl,pins = <
- MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b000
- >;
- };
-
- pinctrl_ecspi1: ecspi1grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
- MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
- MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
- /* CS */
- MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
- >;
- };
-
- pinctrl_hog: hoggrp {
- fsl,pins = <
- /* ITU656_nRESET */
- MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
- /* CAM1_MIRROR */
- MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x130b0
- /* CAM2_MIRROR */
- MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x130b0
- /* CAM_nDETECT */
- MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
- /* ISB_IN1 */
- MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x130b0
- /* ISB_nIN2 */
- MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b0
- /* WARN_LIGHT */
- MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x100b0
- /* ON2_FB */
- MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b0
- /* YACO_nIRQ */
- MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b0
- /* YACO_BOOT0 */
- MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x130b0
- /* YACO_nRESET */
- MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0
- /* FORCE_ON1 */
- MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
- /* AUDIO_nRESET */
- MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0
- /* ITU656_nPDN */
- MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
-
- /* New in HW revision 1 */
- /* ON1_FB */
- MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x100b0
- /* DIP1_FB */
- MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0
- >;
- };
-
- pinctrl_i2c1: i2c1grp {
- fsl,pins = <
- MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
- MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
- >;
- };
-
- pinctrl_i2c3: i2c3grp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
- MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
- >;
- };
-
- pinctrl_ipu1_csi0: ipu1csi0grp {
- fsl,pins = <
- MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
- MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
- MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
- MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
- MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
- MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
- MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
- MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
- MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
- >;
- };
-
- pinctrl_leds: ledsgrp {
- fsl,pins = <
- /* DEBUG0 */
- MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0
- /* DEBUG1 */
- MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0
- /* POWER_LED */
- MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b0
- >;
- };
-
- pinctrl_pwm1: pwm1grp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
- >;
- };
-
- pinctrl_pwm3: pwm3grp {
- fsl,pins = <
- MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b0
- >;
- };
-
- /* YaCO AUX Uart */
- pinctrl_uart1: uart1grp {
- fsl,pins = <
- MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
- MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
- >;
- };
-
- /* YaCO Touchscreen UART */
- pinctrl_uart3: uart3grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
- >;
- };
-
- pinctrl_uart4: uart4grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
- MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
- >;
- };
-
- pinctrl_uart5: uart5grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
- MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
- >;
- };
-
- pinctrl_usbotg: usbotggrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
- /* power enable, high active */
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
- >;
- };
-
- pinctrl_usdhc1: usdhc1grp {
- fsl,pins = <
- MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
- MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
- MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
- MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
- MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
- MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
- MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
- >;
- };
-
- pinctrl_usdhc3: usdhc3grp {
- fsl,pins = <
- MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
- MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
- MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
- MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
- MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
- MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
- MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
- MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
- MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
- MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
- MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
- >;
- };
-};
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 42+ messages in thread* [PATCH v1 13/17] arm: dts: Remove imx6qdl-victgo.dtsi
@ 2022-04-12 7:40 ` Oleksij Rempel
0 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:40 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
The common base is now identical to imx6qdl-vicut1.dtsi, so we can remove
one of both.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-victgo.dts | 2 +-
arch/arm/boot/dts/imx6qdl-victgo.dtsi | 658 --------------------------
2 files changed, 1 insertion(+), 659 deletions(-)
delete mode 100644 arch/arm/boot/dts/imx6qdl-victgo.dtsi
diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 6d61e87405f4..4f6100b2ce2d 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -6,7 +6,7 @@
/dts-v1/;
#include "imx6dl.dtsi"
-#include "imx6qdl-victgo.dtsi"
+#include "imx6qdl-vicut1.dtsi"
/ {
model = "Kverneland TGO";
diff --git a/arch/arm/boot/dts/imx6qdl-victgo.dtsi b/arch/arm/boot/dts/imx6qdl-victgo.dtsi
deleted file mode 100644
index 386e2ca39424..000000000000
--- a/arch/arm/boot/dts/imx6qdl-victgo.dtsi
+++ /dev/null
@@ -1,658 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-/*
- * Copyright (c) 2016 Protonic Holland
- * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
- */
-
-#include <dt-bindings/display/sdtv-standards.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/media/tvp5150.h>
-#include <dt-bindings/sound/fsl-imx-audmux.h>
-
-/ {
- chosen {
- stdout-path = &uart4;
- };
-
- backlight_lcd: backlight {
- compatible = "pwm-backlight";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_backlight>;
- pwms = <&pwm1 0 5000000 0>;
- brightness-levels = <0 16 64 255>;
- num-interpolated-steps = <16>;
- default-brightness-level = <48>;
- power-supply = <®_3v3>;
- enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
- };
-
- backlight_led: backlight_led {
- compatible = "pwm-backlight";
- pwms = <&pwm3 0 5000000 0>;
- brightness-levels = <0 16 64 255>;
- num-interpolated-steps = <16>;
- default-brightness-level = <48>;
- power-supply = <®_3v3>;
- };
-
- connector {
- compatible = "composite-video-connector";
- label = "Composite0";
- sdtv-standards = <SDTV_STD_PAL_B>;
-
- port {
- comp0_out: endpoint {
- remote-endpoint = <&tvp5150_comp0_in>;
- };
- };
- };
-
- counter-0 {
- compatible = "interrupt-counter";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_counter0>;
- gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
- };
-
- counter-1 {
- compatible = "interrupt-counter";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_counter1>;
- gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
- };
-
- counter-2 {
- compatible = "interrupt-counter";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_counter2>;
- gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_leds>;
-
- led-0 {
- label = "debug0";
- function = LED_FUNCTION_HEARTBEAT;
- gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- };
-
- led-1 {
- label = "debug1";
- function = LED_FUNCTION_DISK;
- gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "disk-activity";
- };
-
- led-2 {
- label = "power_led";
- function = LED_FUNCTION_POWER;
- gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
- default-state = "on";
- };
- };
-
- reg_1v8: regulator-1v8 {
- compatible = "regulator-fixed";
- regulator-name = "1v8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- reg_3v3: regulator-3v3 {
- compatible = "regulator-fixed";
- regulator-name = "3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- reg_otg_vbus: regulator-otg-vbus {
- compatible = "regulator-fixed";
- regulator-name = "otg-vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- sound {
- compatible = "simple-audio-card";
- simple-audio-card,name = "prti6q-sgtl5000";
- simple-audio-card,format = "i2s";
- simple-audio-card,widgets =
- "Microphone", "Microphone Jack",
- "Line", "Line In Jack",
- "Headphone", "Headphone Jack",
- "Speaker", "External Speaker";
- simple-audio-card,routing =
- "MIC_IN", "Microphone Jack",
- "LINE_IN", "Line In Jack",
- "Headphone Jack", "HP_OUT",
- "External Speaker", "LINE_OUT";
-
- simple-audio-card,cpu {
- sound-dai = <&ssi1>;
- system-clock-frequency = <0>; /* Do NOT call fsl_ssi_set_dai_sysclk! */
- };
-
- simple-audio-card,codec {
- sound-dai = <&codec>;
- bitclock-master;
- frame-master;
- };
- };
-};
-
-&audmux {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_audmux>;
- status = "okay";
-
- mux-ssi1 {
- fsl,audmux-port = <0>;
- fsl,port-config = <
- IMX_AUDMUX_V2_PTCR_SYN 0
- IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
- IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
- IMX_AUDMUX_V2_PTCR_TFSDIR 0
- IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
- >;
- };
-
- mux-pins3 {
- fsl,audmux-port = <2>;
- fsl,port-config = <
- IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
- 0 IMX_AUDMUX_V2_PDCR_TXRXEN
- >;
- };
-};
-
-&can1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_can1>;
- termination-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
- termination-ohms = <150>;
- status = "okay";
-};
-
-&can2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_can2>;
- status = "okay";
-};
-
-&clks {
- assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
- assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
-};
-
-&ecspi1 {
- cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi1>;
- status = "okay";
-
- flash@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <20000000>;
- };
-};
-
-&gpio2 {
- gpio-line-names =
- "YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
- "", "LED_PWM", "", "", "",
- "", "", "",
- "", "", "", "", "", "ISB_IN2", "ISB_nIN1", "ON_SWITCH",
- "POWER_LED", "", "", "", "", "", "", "";
-};
-
-&gpio3 {
- gpio-line-names =
- "", "", "", "", "", "", "", "",
- "", "", "", "", "", "", "", "",
- "ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
- "CPU_ON1_FB", "USB_OTG_OC", "USB_OTG_PWR", "YACO_IRQ",
- "TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0",
- "YACO_RESET";
-};
-
-&gpio7 {
- gpio-line-names =
- "EMMC_DAT5", "EMMC_DAT4", "EMMC_CMD", "EMMC_CLK", "EMMC_DAT0",
- "EMMC_DAT1", "EMMC_DAT2", "EMMC_DAT3",
- "EMMC_RST", "", "", "", "CAM_DETECT", "", "", "",
- "", "EMMC_DAT7", "EMMC_DAT6", "", "", "", "", "",
- "", "", "", "", "", "", "", "";
-};
-
-&i2c1 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c1>;
- status = "okay";
-
- codec: audio-codec@a {
- compatible = "fsl,sgtl5000";
- reg = <0xa>;
- #sound-dai-cells = <0>;
- clocks = <&clks 201>;
- VDDA-supply = <®_3v3>;
- VDDIO-supply = <®_3v3>;
- VDDD-supply = <®_1v8>;
- };
-
- video-decoder@5c {
- compatible = "ti,tvp5150";
- reg = <0x5c>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
-
- tvp5150_comp0_in: endpoint {
- remote-endpoint = <&comp0_out>;
- };
- };
-
- /* Output port 2 is video output pad */
- port@2 {
- reg = <2>;
-
- tvp5151_to_ipu1_csi0_mux: endpoint {
- remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
- };
- };
- };
-
- /* additional i2c devices are added automatically by the boot loader */
-};
-
-&i2c3 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c3>;
- status = "okay";
-
- adc@49 {
- compatible = "ti,ads1015";
- reg = <0x49>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- channel@4 {
- reg = <4>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
-
- channel@5 {
- reg = <5>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
-
- channel@6 {
- reg = <6>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
-
- channel@7 {
- reg = <7>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
- };
-
- rtc@51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
-
- tsens0: temperature-sensor@70 {
- compatible = "ti,tmp103";
- reg = <0x70>;
- #thermal-sensor-cells = <0>;
- };
-};
-
-&ipu1_csi0 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ipu1_csi0>;
- status = "okay";
-};
-
-&ipu1_csi0_mux_from_parallel_sensor {
- remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
-};
-
-&ldb {
- status = "okay";
-
- lvds-channel@0 {
- status = "okay";
-
- port@4 {
- reg = <4>;
-
- lvds0_out: endpoint {
- remote-endpoint = <&panel_in>;
- };
- };
- };
-};
-
-&pwm1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm1>;
- status = "okay";
-};
-
-&pwm3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm3>;
- status = "okay";
-};
-
-&ssi1 {
- status = "okay";
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
- status = "okay";
-};
-
-&uart3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart3>;
- status = "okay";
-};
-
-&uart4 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart4>;
- status = "okay";
-};
-
-&uart5 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart5>;
- status = "okay";
-};
-
-&usbh1 {
- pinctrl-names = "default";
- phy_type = "utmi";
- dr_mode = "host";
- status = "okay";
-};
-
-&usbotg {
- vbus-supply = <®_otg_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg>;
- phy_type = "utmi";
- dr_mode = "host";
- disable-over-current;
- status = "okay";
-};
-
-&usdhc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc1>;
- cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
- no-1-8-v;
- disable-wp;
- cap-sd-highspeed;
- no-mmc;
- no-sdio;
- status = "okay";
-};
-
-&usdhc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc3>;
- bus-width = <8>;
- no-1-8-v;
- non-removable;
- no-sd;
- no-sdio;
- status = "okay";
-};
-
-&iomuxc {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_hog>;
-
- pinctrl_audmux: audmuxgrp {
- fsl,pins = <
- /* SGTL5000 sys_mclk */
- MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
- MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
- MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
- MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
- MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
- >;
- };
-
- pinctrl_backlight: backlightgrp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
- >;
- };
-
- pinctrl_can1: can1grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000
- MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008
- /* CAN1_SR */
- MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008
- /* CAN1_TERM */
- MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b088
- >;
- };
-
- pinctrl_can2: can2grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b000
- MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x3008
- /* CAN2_SR */
- MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13008
- >;
- };
-
- pinctrl_counter0: counter0grp {
- fsl,pins = <
- MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b000
- >;
- };
-
- pinctrl_counter1: counter1grp {
- fsl,pins = <
- MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b000
- >;
- };
-
- pinctrl_counter2: counter2grp {
- fsl,pins = <
- MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b000
- >;
- };
-
- pinctrl_ecspi1: ecspi1grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
- MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
- MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
- /* CS */
- MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
- >;
- };
-
- pinctrl_hog: hoggrp {
- fsl,pins = <
- /* ITU656_nRESET */
- MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
- /* CAM1_MIRROR */
- MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x130b0
- /* CAM2_MIRROR */
- MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x130b0
- /* CAM_nDETECT */
- MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
- /* ISB_IN1 */
- MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x130b0
- /* ISB_nIN2 */
- MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b0
- /* WARN_LIGHT */
- MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x100b0
- /* ON2_FB */
- MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b0
- /* YACO_nIRQ */
- MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b0
- /* YACO_BOOT0 */
- MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x130b0
- /* YACO_nRESET */
- MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0
- /* FORCE_ON1 */
- MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
- /* AUDIO_nRESET */
- MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0
- /* ITU656_nPDN */
- MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
-
- /* New in HW revision 1 */
- /* ON1_FB */
- MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x100b0
- /* DIP1_FB */
- MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0
- >;
- };
-
- pinctrl_i2c1: i2c1grp {
- fsl,pins = <
- MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
- MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
- >;
- };
-
- pinctrl_i2c3: i2c3grp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
- MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
- >;
- };
-
- pinctrl_ipu1_csi0: ipu1csi0grp {
- fsl,pins = <
- MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
- MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
- MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
- MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
- MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
- MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
- MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
- MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
- MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
- >;
- };
-
- pinctrl_leds: ledsgrp {
- fsl,pins = <
- /* DEBUG0 */
- MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0
- /* DEBUG1 */
- MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0
- /* POWER_LED */
- MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b0
- >;
- };
-
- pinctrl_pwm1: pwm1grp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
- >;
- };
-
- pinctrl_pwm3: pwm3grp {
- fsl,pins = <
- MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b0
- >;
- };
-
- /* YaCO AUX Uart */
- pinctrl_uart1: uart1grp {
- fsl,pins = <
- MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
- MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
- >;
- };
-
- /* YaCO Touchscreen UART */
- pinctrl_uart3: uart3grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
- >;
- };
-
- pinctrl_uart4: uart4grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
- MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
- >;
- };
-
- pinctrl_uart5: uart5grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
- MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
- >;
- };
-
- pinctrl_usbotg: usbotggrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
- /* power enable, high active */
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
- >;
- };
-
- pinctrl_usdhc1: usdhc1grp {
- fsl,pins = <
- MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
- MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
- MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
- MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
- MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
- MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
- MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
- >;
- };
-
- pinctrl_usdhc3: usdhc3grp {
- fsl,pins = <
- MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
- MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
- MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
- MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
- MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
- MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
- MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
- MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
- MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
- MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
- MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
- >;
- };
-};
--
2.30.2
^ permalink raw reply related [flat|nested] 42+ messages in thread
* [PATCH v1 14/17] arm: dts: imx6qdl-vicut1: Factor out common parts of 12inch board variants
2022-04-12 7:39 ` Oleksij Rempel
@ 2022-04-12 7:40 ` Oleksij Rempel
-1 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:40 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
Factor out common parts of vicut1 and vicutp to reduce maintenance
overhead.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-vicut1.dts | 123 +-----------------
arch/arm/boot/dts/imx6q-vicut1.dts | 123 +-----------------
arch/arm/boot/dts/imx6qdl-vicut1-12inch.dtsi | 128 +++++++++++++++++++
arch/arm/boot/dts/imx6qp-vicutp.dts | 123 +-----------------
4 files changed, 131 insertions(+), 366 deletions(-)
create mode 100644 arch/arm/boot/dts/imx6qdl-vicut1-12inch.dtsi
diff --git a/arch/arm/boot/dts/imx6dl-vicut1.dts b/arch/arm/boot/dts/imx6dl-vicut1.dts
index c6a904bbed01..5035d303447d 100644
--- a/arch/arm/boot/dts/imx6dl-vicut1.dts
+++ b/arch/arm/boot/dts/imx6dl-vicut1.dts
@@ -6,130 +6,9 @@
/dts-v1/;
#include "imx6dl.dtsi"
#include "imx6qdl-vicut1.dtsi"
+#include "imx6qdl-vicut1-12inch.dtsi"
/ {
model = "Kverneland UT1 Board";
compatible = "kvg,vicut1", "fsl,imx6dl";
-
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpiokeys>;
- autorepeat;
-
- power {
- label = "Power Button";
- gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_POWER>;
- wakeup-source;
- };
- };
-
- panel {
- compatible = "kyo,tcg121xglp";
- backlight = <&backlight_lcd>;
- power-supply = <®_3v3>;
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&lvds0_out>;
- };
- };
- };
-};
-
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rgmii-id";
- phy-handle = <&rgmii_phy>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* Microchip KSZ9031RNX PHY */
- rgmii_phy: ethernet-phy@0 {
- reg = <0>;
- interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
- reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
- reset-assert-us = <10000>;
- reset-deassert-us = <300>;
- };
- };
-};
-
-&gpio1 {
- gpio-line-names =
- "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
- "CAM2_MIRROR", "", "", "SMBALERT",
- "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
- "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
- "SD1_DATA3", "ETH_MDIO", "",
- "", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
-};
-
-&gpio4 {
- gpio-line-names =
- "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
- "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
- "CAN2_SR", "CAN2_TX", "CAN2_RX",
- "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
- "HITCH_IN_OUT",
- "LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
- "ISB_LED";
-};
-
-&gpio5 {
- gpio-line-names =
- "", "", "", "", "", "", "", "",
- "", "", "", "", "", "", "", "",
- "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
- "I2S_BITCLK", "I2S_DOUT",
- "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
- "YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
-};
-
-&gpio6 {
- gpio-line-names =
- "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
- "ITU656_D6", "ITU656_D7", "", "",
- "", "", "", "", "", "", "", "",
- "", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
- "RGMII_TD3",
- "RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
- "RGMII_RD2", "RGMII_RD3", "", "";
-};
-
-&iomuxc {
- pinctrl_enet: enetgrp {
- fsl,pins = <
- MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
- MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
- MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
- MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
- MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
- MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
- MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
- MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
- MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
- MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
- MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
- MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
- MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
- /* Phy reset */
- MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
- MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
- >;
- };
-
- pinctrl_gpiokeys: gpiokeygrp {
- fsl,pins = <
- /* nON_SWITCH */
- MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
- >;
- };
};
diff --git a/arch/arm/boot/dts/imx6q-vicut1.dts b/arch/arm/boot/dts/imx6q-vicut1.dts
index 8b228d5fc4a3..dd91aff3f9e2 100644
--- a/arch/arm/boot/dts/imx6q-vicut1.dts
+++ b/arch/arm/boot/dts/imx6q-vicut1.dts
@@ -6,130 +6,9 @@
/dts-v1/;
#include "imx6q.dtsi"
#include "imx6qdl-vicut1.dtsi"
+#include "imx6qdl-vicut1-12inch.dtsi"
/ {
model = "Kverneland UT1Q Board";
compatible = "kvg,vicut1q", "fsl,imx6q";
-
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpiokeys>;
- autorepeat;
-
- power {
- label = "Power Button";
- gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_POWER>;
- wakeup-source;
- };
- };
-
- panel {
- compatible = "kyo,tcg121xglp";
- backlight = <&backlight_lcd>;
- power-supply = <®_3v3>;
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&lvds0_out>;
- };
- };
- };
-};
-
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rgmii-id";
- phy-handle = <&rgmii_phy>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* Microchip KSZ9031RNX PHY */
- rgmii_phy: ethernet-phy@0 {
- reg = <0>;
- interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
- reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
- reset-assert-us = <10000>;
- reset-deassert-us = <300>;
- };
- };
-};
-
-&gpio1 {
- gpio-line-names =
- "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
- "CAM2_MIRROR", "", "", "SMBALERT",
- "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
- "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
- "SD1_DATA3", "ETH_MDIO", "",
- "", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
-};
-
-&gpio4 {
- gpio-line-names =
- "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
- "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
- "CAN2_SR", "CAN2_TX", "CAN2_RX",
- "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
- "HITCH_IN_OUT",
- "LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
- "ISB_LED";
-};
-
-&gpio5 {
- gpio-line-names =
- "", "", "", "", "", "", "", "",
- "", "", "", "", "", "", "", "",
- "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
- "I2S_BITCLK", "I2S_DOUT",
- "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
- "YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
-};
-
-&gpio6 {
- gpio-line-names =
- "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
- "ITU656_D6", "ITU656_D7", "", "",
- "", "", "", "", "", "", "", "",
- "", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
- "RGMII_TD3",
- "RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
- "RGMII_RD2", "RGMII_RD3", "", "";
-};
-
-&iomuxc {
- pinctrl_enet: enetgrp {
- fsl,pins = <
- MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
- MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
- MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
- MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
- MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
- MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
- MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
- MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
- MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
- MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
- MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
- MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
- MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
- /* Phy reset */
- MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
- MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
- >;
- };
-
- pinctrl_gpiokeys: gpiokeygrp {
- fsl,pins = <
- /* nON_SWITCH */
- MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
- >;
- };
};
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1-12inch.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1-12inch.dtsi
new file mode 100644
index 000000000000..f505f2704530
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-vicut1-12inch.dtsi
@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2021 Protonic Holland
+ */
+
+/ {
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiokeys>;
+ autorepeat;
+
+ power {
+ label = "Power Button";
+ gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+ panel {
+ compatible = "kyo,tcg121xglp";
+ backlight = <&backlight_lcd>;
+ power-supply = <®_3v3>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ9031RNX PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&gpio1 {
+ gpio-line-names =
+ "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
+ "CAM2_MIRROR", "", "", "SMBALERT",
+ "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+ "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
+ "SD1_DATA3", "ETH_MDIO", "",
+ "", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
+ "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
+ "CAN2_SR", "CAN2_TX", "CAN2_RX",
+ "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
+ "HITCH_IN_OUT",
+ "LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
+ "ISB_LED";
+};
+
+&gpio5 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
+ "I2S_BITCLK", "I2S_DOUT",
+ "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
+ "YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
+};
+
+&gpio6 {
+ gpio-line-names =
+ "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
+ "ITU656_D6", "ITU656_D7", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
+ "RGMII_TD3",
+ "RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
+ "RGMII_RD2", "RGMII_RD3", "", "";
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+ /* Phy reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
+ >;
+ };
+
+ pinctrl_gpiokeys: gpiokeygrp {
+ fsl,pins = <
+ /* nON_SWITCH */
+ MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6qp-vicutp.dts b/arch/arm/boot/dts/imx6qp-vicutp.dts
index 31c748e9d92f..49ff145fffe5 100644
--- a/arch/arm/boot/dts/imx6qp-vicutp.dts
+++ b/arch/arm/boot/dts/imx6qp-vicutp.dts
@@ -6,130 +6,9 @@
/dts-v1/;
#include "imx6qp.dtsi"
#include "imx6qdl-vicut1.dtsi"
+#include "imx6qdl-vicut1-12inch.dtsi"
/ {
model = "Kverneland UT1P Board";
compatible = "kvg,vicutp", "fsl,imx6qp";
-
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpiokeys>;
- autorepeat;
-
- power {
- label = "Power Button";
- gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_POWER>;
- wakeup-source;
- };
- };
-
- panel {
- compatible = "kyo,tcg121xglp";
- backlight = <&backlight_lcd>;
- power-supply = <®_3v3>;
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&lvds0_out>;
- };
- };
- };
-};
-
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rgmii-id";
- phy-handle = <&rgmii_phy>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* Microchip KSZ9031RNX PHY */
- rgmii_phy: ethernet-phy@0 {
- reg = <0>;
- interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
- reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
- reset-assert-us = <10000>;
- reset-deassert-us = <300>;
- };
- };
-};
-
-&gpio1 {
- gpio-line-names =
- "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
- "CAM2_MIRROR", "", "", "SMBALERT",
- "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
- "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
- "SD1_DATA3", "ETH_MDIO", "",
- "", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
-};
-
-&gpio4 {
- gpio-line-names =
- "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
- "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
- "CAN2_SR", "CAN2_TX", "CAN2_RX",
- "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
- "HITCH_IN_OUT",
- "LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
- "ISB_LED";
-};
-
-&gpio5 {
- gpio-line-names =
- "", "", "", "", "", "", "", "",
- "", "", "", "", "", "", "", "",
- "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
- "I2S_BITCLK", "I2S_DOUT",
- "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
- "YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
-};
-
-&gpio6 {
- gpio-line-names =
- "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
- "ITU656_D6", "ITU656_D7", "", "",
- "", "", "", "", "", "", "", "",
- "", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
- "RGMII_TD3",
- "RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
- "RGMII_RD2", "RGMII_RD3", "", "";
-};
-
-&iomuxc {
- pinctrl_enet: enetgrp {
- fsl,pins = <
- MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
- MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
- MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
- MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
- MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
- MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
- MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
- MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
- MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
- MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
- MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
- MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
- MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
- /* Phy reset */
- MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
- MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
- >;
- };
-
- pinctrl_gpiokeys: gpiokeygrp {
- fsl,pins = <
- /* nON_SWITCH */
- MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
- >;
- };
};
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 42+ messages in thread* [PATCH v1 14/17] arm: dts: imx6qdl-vicut1: Factor out common parts of 12inch board variants
@ 2022-04-12 7:40 ` Oleksij Rempel
0 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:40 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
Factor out common parts of vicut1 and vicutp to reduce maintenance
overhead.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-vicut1.dts | 123 +-----------------
arch/arm/boot/dts/imx6q-vicut1.dts | 123 +-----------------
arch/arm/boot/dts/imx6qdl-vicut1-12inch.dtsi | 128 +++++++++++++++++++
arch/arm/boot/dts/imx6qp-vicutp.dts | 123 +-----------------
4 files changed, 131 insertions(+), 366 deletions(-)
create mode 100644 arch/arm/boot/dts/imx6qdl-vicut1-12inch.dtsi
diff --git a/arch/arm/boot/dts/imx6dl-vicut1.dts b/arch/arm/boot/dts/imx6dl-vicut1.dts
index c6a904bbed01..5035d303447d 100644
--- a/arch/arm/boot/dts/imx6dl-vicut1.dts
+++ b/arch/arm/boot/dts/imx6dl-vicut1.dts
@@ -6,130 +6,9 @@
/dts-v1/;
#include "imx6dl.dtsi"
#include "imx6qdl-vicut1.dtsi"
+#include "imx6qdl-vicut1-12inch.dtsi"
/ {
model = "Kverneland UT1 Board";
compatible = "kvg,vicut1", "fsl,imx6dl";
-
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpiokeys>;
- autorepeat;
-
- power {
- label = "Power Button";
- gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_POWER>;
- wakeup-source;
- };
- };
-
- panel {
- compatible = "kyo,tcg121xglp";
- backlight = <&backlight_lcd>;
- power-supply = <®_3v3>;
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&lvds0_out>;
- };
- };
- };
-};
-
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rgmii-id";
- phy-handle = <&rgmii_phy>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* Microchip KSZ9031RNX PHY */
- rgmii_phy: ethernet-phy@0 {
- reg = <0>;
- interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
- reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
- reset-assert-us = <10000>;
- reset-deassert-us = <300>;
- };
- };
-};
-
-&gpio1 {
- gpio-line-names =
- "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
- "CAM2_MIRROR", "", "", "SMBALERT",
- "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
- "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
- "SD1_DATA3", "ETH_MDIO", "",
- "", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
-};
-
-&gpio4 {
- gpio-line-names =
- "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
- "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
- "CAN2_SR", "CAN2_TX", "CAN2_RX",
- "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
- "HITCH_IN_OUT",
- "LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
- "ISB_LED";
-};
-
-&gpio5 {
- gpio-line-names =
- "", "", "", "", "", "", "", "",
- "", "", "", "", "", "", "", "",
- "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
- "I2S_BITCLK", "I2S_DOUT",
- "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
- "YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
-};
-
-&gpio6 {
- gpio-line-names =
- "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
- "ITU656_D6", "ITU656_D7", "", "",
- "", "", "", "", "", "", "", "",
- "", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
- "RGMII_TD3",
- "RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
- "RGMII_RD2", "RGMII_RD3", "", "";
-};
-
-&iomuxc {
- pinctrl_enet: enetgrp {
- fsl,pins = <
- MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
- MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
- MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
- MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
- MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
- MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
- MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
- MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
- MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
- MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
- MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
- MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
- MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
- /* Phy reset */
- MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
- MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
- >;
- };
-
- pinctrl_gpiokeys: gpiokeygrp {
- fsl,pins = <
- /* nON_SWITCH */
- MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
- >;
- };
};
diff --git a/arch/arm/boot/dts/imx6q-vicut1.dts b/arch/arm/boot/dts/imx6q-vicut1.dts
index 8b228d5fc4a3..dd91aff3f9e2 100644
--- a/arch/arm/boot/dts/imx6q-vicut1.dts
+++ b/arch/arm/boot/dts/imx6q-vicut1.dts
@@ -6,130 +6,9 @@
/dts-v1/;
#include "imx6q.dtsi"
#include "imx6qdl-vicut1.dtsi"
+#include "imx6qdl-vicut1-12inch.dtsi"
/ {
model = "Kverneland UT1Q Board";
compatible = "kvg,vicut1q", "fsl,imx6q";
-
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpiokeys>;
- autorepeat;
-
- power {
- label = "Power Button";
- gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_POWER>;
- wakeup-source;
- };
- };
-
- panel {
- compatible = "kyo,tcg121xglp";
- backlight = <&backlight_lcd>;
- power-supply = <®_3v3>;
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&lvds0_out>;
- };
- };
- };
-};
-
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rgmii-id";
- phy-handle = <&rgmii_phy>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* Microchip KSZ9031RNX PHY */
- rgmii_phy: ethernet-phy@0 {
- reg = <0>;
- interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
- reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
- reset-assert-us = <10000>;
- reset-deassert-us = <300>;
- };
- };
-};
-
-&gpio1 {
- gpio-line-names =
- "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
- "CAM2_MIRROR", "", "", "SMBALERT",
- "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
- "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
- "SD1_DATA3", "ETH_MDIO", "",
- "", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
-};
-
-&gpio4 {
- gpio-line-names =
- "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
- "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
- "CAN2_SR", "CAN2_TX", "CAN2_RX",
- "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
- "HITCH_IN_OUT",
- "LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
- "ISB_LED";
-};
-
-&gpio5 {
- gpio-line-names =
- "", "", "", "", "", "", "", "",
- "", "", "", "", "", "", "", "",
- "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
- "I2S_BITCLK", "I2S_DOUT",
- "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
- "YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
-};
-
-&gpio6 {
- gpio-line-names =
- "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
- "ITU656_D6", "ITU656_D7", "", "",
- "", "", "", "", "", "", "", "",
- "", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
- "RGMII_TD3",
- "RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
- "RGMII_RD2", "RGMII_RD3", "", "";
-};
-
-&iomuxc {
- pinctrl_enet: enetgrp {
- fsl,pins = <
- MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
- MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
- MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
- MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
- MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
- MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
- MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
- MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
- MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
- MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
- MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
- MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
- MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
- /* Phy reset */
- MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
- MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
- >;
- };
-
- pinctrl_gpiokeys: gpiokeygrp {
- fsl,pins = <
- /* nON_SWITCH */
- MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
- >;
- };
};
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1-12inch.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1-12inch.dtsi
new file mode 100644
index 000000000000..f505f2704530
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-vicut1-12inch.dtsi
@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2021 Protonic Holland
+ */
+
+/ {
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiokeys>;
+ autorepeat;
+
+ power {
+ label = "Power Button";
+ gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+ panel {
+ compatible = "kyo,tcg121xglp";
+ backlight = <&backlight_lcd>;
+ power-supply = <®_3v3>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ9031RNX PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&gpio1 {
+ gpio-line-names =
+ "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
+ "CAM2_MIRROR", "", "", "SMBALERT",
+ "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+ "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
+ "SD1_DATA3", "ETH_MDIO", "",
+ "", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
+ "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
+ "CAN2_SR", "CAN2_TX", "CAN2_RX",
+ "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
+ "HITCH_IN_OUT",
+ "LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
+ "ISB_LED";
+};
+
+&gpio5 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
+ "I2S_BITCLK", "I2S_DOUT",
+ "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
+ "YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
+};
+
+&gpio6 {
+ gpio-line-names =
+ "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
+ "ITU656_D6", "ITU656_D7", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
+ "RGMII_TD3",
+ "RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
+ "RGMII_RD2", "RGMII_RD3", "", "";
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+ /* Phy reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
+ >;
+ };
+
+ pinctrl_gpiokeys: gpiokeygrp {
+ fsl,pins = <
+ /* nON_SWITCH */
+ MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6qp-vicutp.dts b/arch/arm/boot/dts/imx6qp-vicutp.dts
index 31c748e9d92f..49ff145fffe5 100644
--- a/arch/arm/boot/dts/imx6qp-vicutp.dts
+++ b/arch/arm/boot/dts/imx6qp-vicutp.dts
@@ -6,130 +6,9 @@
/dts-v1/;
#include "imx6qp.dtsi"
#include "imx6qdl-vicut1.dtsi"
+#include "imx6qdl-vicut1-12inch.dtsi"
/ {
model = "Kverneland UT1P Board";
compatible = "kvg,vicutp", "fsl,imx6qp";
-
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpiokeys>;
- autorepeat;
-
- power {
- label = "Power Button";
- gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_POWER>;
- wakeup-source;
- };
- };
-
- panel {
- compatible = "kyo,tcg121xglp";
- backlight = <&backlight_lcd>;
- power-supply = <®_3v3>;
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&lvds0_out>;
- };
- };
- };
-};
-
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rgmii-id";
- phy-handle = <&rgmii_phy>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* Microchip KSZ9031RNX PHY */
- rgmii_phy: ethernet-phy@0 {
- reg = <0>;
- interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
- reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
- reset-assert-us = <10000>;
- reset-deassert-us = <300>;
- };
- };
-};
-
-&gpio1 {
- gpio-line-names =
- "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
- "CAM2_MIRROR", "", "", "SMBALERT",
- "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
- "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
- "SD1_DATA3", "ETH_MDIO", "",
- "", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
-};
-
-&gpio4 {
- gpio-line-names =
- "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
- "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
- "CAN2_SR", "CAN2_TX", "CAN2_RX",
- "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
- "HITCH_IN_OUT",
- "LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
- "ISB_LED";
-};
-
-&gpio5 {
- gpio-line-names =
- "", "", "", "", "", "", "", "",
- "", "", "", "", "", "", "", "",
- "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
- "I2S_BITCLK", "I2S_DOUT",
- "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
- "YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
-};
-
-&gpio6 {
- gpio-line-names =
- "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
- "ITU656_D6", "ITU656_D7", "", "",
- "", "", "", "", "", "", "", "",
- "", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
- "RGMII_TD3",
- "RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
- "RGMII_RD2", "RGMII_RD3", "", "";
-};
-
-&iomuxc {
- pinctrl_enet: enetgrp {
- fsl,pins = <
- MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
- MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
- MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
- MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
- MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
- MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
- MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
- MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
- MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
- MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
- MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
- MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
- MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
- /* Phy reset */
- MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
- MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
- >;
- };
-
- pinctrl_gpiokeys: gpiokeygrp {
- fsl,pins = <
- /* nON_SWITCH */
- MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
- >;
- };
};
--
2.30.2
^ permalink raw reply related [flat|nested] 42+ messages in thread
* [PATCH v1 15/17] arm: dts: imx6dl-victgo.dts: Remove touchscreen x axis inversion
2022-04-12 7:39 ` Oleksij Rempel
@ 2022-04-12 7:40 ` Oleksij Rempel
-1 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:40 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
X axis is not inverted in hardware.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-victgo.dts | 1 -
1 file changed, 1 deletion(-)
diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 4f6100b2ce2d..516ec915a911 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -94,7 +94,6 @@ touchscreen {
<&adc_ts 5>;
io-channel-names = "y", "z1", "z2", "x";
touchscreen-min-pressure = <64687>;
- touchscreen-inverted-x;
touchscreen-inverted-y;
touchscreen-x-plate-ohms = <300>;
touchscreen-y-plate-ohms = <800>;
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 42+ messages in thread* [PATCH v1 15/17] arm: dts: imx6dl-victgo.dts: Remove touchscreen x axis inversion
@ 2022-04-12 7:40 ` Oleksij Rempel
0 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:40 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
X axis is not inverted in hardware.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-victgo.dts | 1 -
1 file changed, 1 deletion(-)
diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 4f6100b2ce2d..516ec915a911 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -94,7 +94,6 @@ touchscreen {
<&adc_ts 5>;
io-channel-names = "y", "z1", "z2", "x";
touchscreen-min-pressure = <64687>;
- touchscreen-inverted-x;
touchscreen-inverted-y;
touchscreen-x-plate-ohms = <300>;
touchscreen-y-plate-ohms = <800>;
--
2.30.2
^ permalink raw reply related [flat|nested] 42+ messages in thread
* [PATCH v1 16/17] arm: dts: imx6qdl-vicut1.dtsi: Add missing ISB led node
2022-04-12 7:39 ` Oleksij Rempel
@ 2022-04-12 7:40 ` Oleksij Rempel
-1 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:40 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
Add missing ISB led node.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index 2a86136a04e8..c928bd854e92 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -95,6 +95,13 @@ led-2 {
gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
+
+ led-3 {
+ label = "isb_led";
+ function = LED_FUNCTION_POWER;
+ gpios = <&gpio4 31 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
};
reg_1v8: regulator-1v8 {
@@ -574,6 +581,8 @@ MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0
MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0
/* POWER_LED */
MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b0
+ /* ISB_LED */
+ MX6QDL_PAD_DISP0_DAT10__GPIO4_IO31 0x1b0b0
>;
};
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 42+ messages in thread* [PATCH v1 16/17] arm: dts: imx6qdl-vicut1.dtsi: Add missing ISB led node
@ 2022-04-12 7:40 ` Oleksij Rempel
0 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:40 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: David Jander, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Robin van der Gracht
From: David Jander <david@protonic.nl>
Add missing ISB led node.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index 2a86136a04e8..c928bd854e92 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -95,6 +95,13 @@ led-2 {
gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
+
+ led-3 {
+ label = "isb_led";
+ function = LED_FUNCTION_POWER;
+ gpios = <&gpio4 31 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
};
reg_1v8: regulator-1v8 {
@@ -574,6 +581,8 @@ MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0
MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0
/* POWER_LED */
MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b0
+ /* ISB_LED */
+ MX6QDL_PAD_DISP0_DAT10__GPIO4_IO31 0x1b0b0
>;
};
--
2.30.2
^ permalink raw reply related [flat|nested] 42+ messages in thread
* [PATCH v1 17/17] arm: dts: imx6qdl-vicut1.dtsi: add thermal zone and attach tmp103 to it.
2022-04-12 7:39 ` Oleksij Rempel
@ 2022-04-12 7:40 ` Oleksij Rempel
-1 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:40 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Robin van der Gracht
Latest version of ti,tmp103 driver supports thermal zone. So make use of
it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 11 ++++++++++-
1 file changed, 10 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index c928bd854e92..a1676b5d2980 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -153,6 +153,14 @@ simple-audio-card,codec {
frame-master;
};
};
+
+ thermal-zones {
+ chassis-thermal {
+ polling-delay = <20000>;
+ polling-delay-passive = <0>;
+ thermal-sensors = <&tsens0>;
+ };
+ };
};
&audmux {
@@ -323,9 +331,10 @@ rtc@51 {
reg = <0x51>;
};
- temperature-sensor@70 {
+ tsens0: temperature-sensor@70 {
compatible = "ti,tmp103";
reg = <0x70>;
+ #thermal-sensor-cells = <0>;
};
};
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 42+ messages in thread* [PATCH v1 17/17] arm: dts: imx6qdl-vicut1.dtsi: add thermal zone and attach tmp103 to it.
@ 2022-04-12 7:40 ` Oleksij Rempel
0 siblings, 0 replies; 42+ messages in thread
From: Oleksij Rempel @ 2022-04-12 7:40 UTC (permalink / raw)
To: Rob Herring, Shawn Guo
Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Robin van der Gracht
Latest version of ti,tmp103 driver supports thermal zone. So make use of
it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 11 ++++++++++-
1 file changed, 10 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index c928bd854e92..a1676b5d2980 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -153,6 +153,14 @@ simple-audio-card,codec {
frame-master;
};
};
+
+ thermal-zones {
+ chassis-thermal {
+ polling-delay = <20000>;
+ polling-delay-passive = <0>;
+ thermal-sensors = <&tsens0>;
+ };
+ };
};
&audmux {
@@ -323,9 +331,10 @@ rtc@51 {
reg = <0x51>;
};
- temperature-sensor@70 {
+ tsens0: temperature-sensor@70 {
compatible = "ti,tmp103";
reg = <0x70>;
+ #thermal-sensor-cells = <0>;
};
};
--
2.30.2
^ permalink raw reply related [flat|nested] 42+ messages in thread
* Re: [PATCH v1 00/17] protonic fixes
2022-04-12 7:39 ` Oleksij Rempel
@ 2022-04-18 11:48 ` Shawn Guo
-1 siblings, 0 replies; 42+ messages in thread
From: Shawn Guo @ 2022-04-18 11:48 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Rob Herring, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Robin van der Gracht
On Tue, Apr 12, 2022 at 09:39:47AM +0200, Oleksij Rempel wrote:
> This patch series provide two main part of changes:
> - Remove prototype specific deprecated code not used in production.
> - Unify vicut1 and victgo variants to reduce maintaining overhead.
>
> David Jander (16):
> arm: dts: imx6qdl-vicut1.dtsi: remove TiWi module
> arm: dts: imx6qdl-vicut1.dtsi: Put nON_SWITCH in own pinctrl grp
> arm: dts: imx6qdl-vicut1.dtsi: Remove PCIe
> arm: dts: imx6qdl-vicut1/victgo: Remove UART2
> arm: dts: imx6qdl-vicut1.dtsi: Fix LED names
> arm: dts: imx6qdl-vicut1.dtsi: Fix debug LED gpio pins
> arm: dts: imx6qdl-vicut1.dtsi: Update GPIO line names
> arm: dts: imx6qdl-vicut1.dtsi: Remove conflicting pinctrl entry
> arm: dts: imx6q-vicut1.dts: remove sata node
> arm: dts: imx6dl-victgo.dts: update gpio names
> arm: dts: imx6dl-victgo.dts: Factor out common parts to
> imx6qdl-victgo.dtsi
> arm: dts: imx6qdl-vicut1.dtsi: Move some node out to DTS files
> arm: dts: Remove imx6qdl-victgo.dtsi
> arm: dts: imx6qdl-vicut1: Factor out common parts of 12inch board
> variants
> arm: dts: imx6dl-victgo.dts: Remove touchscreen x axis inversion
> arm: dts: imx6qdl-vicut1.dtsi: Add missing ISB led node
>
> Oleksij Rempel (1):
> arm: dts: imx6qdl-vicut1.dtsi: add thermal zone and attach tmp103 to
> it.
s/arm:/ARM: in patch subject.
Shawn
>
> arch/arm/boot/dts/imx6dl-victgo.dts | 682 +------------------
> arch/arm/boot/dts/imx6dl-vicut1.dts | 1 +
> arch/arm/boot/dts/imx6q-vicut1.dts | 5 +-
> arch/arm/boot/dts/imx6qdl-vicut1-12inch.dtsi | 128 ++++
> arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 222 +-----
> arch/arm/boot/dts/imx6qp-vicutp.dts | 1 +
> 6 files changed, 178 insertions(+), 861 deletions(-)
> create mode 100644 arch/arm/boot/dts/imx6qdl-vicut1-12inch.dtsi
>
> --
> 2.30.2
>
^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [PATCH v1 00/17] protonic fixes
@ 2022-04-18 11:48 ` Shawn Guo
0 siblings, 0 replies; 42+ messages in thread
From: Shawn Guo @ 2022-04-18 11:48 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Rob Herring, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Robin van der Gracht
On Tue, Apr 12, 2022 at 09:39:47AM +0200, Oleksij Rempel wrote:
> This patch series provide two main part of changes:
> - Remove prototype specific deprecated code not used in production.
> - Unify vicut1 and victgo variants to reduce maintaining overhead.
>
> David Jander (16):
> arm: dts: imx6qdl-vicut1.dtsi: remove TiWi module
> arm: dts: imx6qdl-vicut1.dtsi: Put nON_SWITCH in own pinctrl grp
> arm: dts: imx6qdl-vicut1.dtsi: Remove PCIe
> arm: dts: imx6qdl-vicut1/victgo: Remove UART2
> arm: dts: imx6qdl-vicut1.dtsi: Fix LED names
> arm: dts: imx6qdl-vicut1.dtsi: Fix debug LED gpio pins
> arm: dts: imx6qdl-vicut1.dtsi: Update GPIO line names
> arm: dts: imx6qdl-vicut1.dtsi: Remove conflicting pinctrl entry
> arm: dts: imx6q-vicut1.dts: remove sata node
> arm: dts: imx6dl-victgo.dts: update gpio names
> arm: dts: imx6dl-victgo.dts: Factor out common parts to
> imx6qdl-victgo.dtsi
> arm: dts: imx6qdl-vicut1.dtsi: Move some node out to DTS files
> arm: dts: Remove imx6qdl-victgo.dtsi
> arm: dts: imx6qdl-vicut1: Factor out common parts of 12inch board
> variants
> arm: dts: imx6dl-victgo.dts: Remove touchscreen x axis inversion
> arm: dts: imx6qdl-vicut1.dtsi: Add missing ISB led node
>
> Oleksij Rempel (1):
> arm: dts: imx6qdl-vicut1.dtsi: add thermal zone and attach tmp103 to
> it.
s/arm:/ARM: in patch subject.
Shawn
>
> arch/arm/boot/dts/imx6dl-victgo.dts | 682 +------------------
> arch/arm/boot/dts/imx6dl-vicut1.dts | 1 +
> arch/arm/boot/dts/imx6q-vicut1.dts | 5 +-
> arch/arm/boot/dts/imx6qdl-vicut1-12inch.dtsi | 128 ++++
> arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 222 +-----
> arch/arm/boot/dts/imx6qp-vicutp.dts | 1 +
> 6 files changed, 178 insertions(+), 861 deletions(-)
> create mode 100644 arch/arm/boot/dts/imx6qdl-vicut1-12inch.dtsi
>
> --
> 2.30.2
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 42+ messages in thread