[PATCH v5] arm64: dts: ti: k3-j721s2: Add support for CAN instances 3 and 5 in main domain

* [PATCH v5] arm64: dts: ti: k3-j721s2: Add support for CAN instances 3 and 5 in main domain
@ 2023-07-24 11:17 Bhavya Kapoor
  2023-07-24 17:55 ` Nishanth Menon
  0 siblings, 1 reply; 2+ messages in thread
From: Bhavya Kapoor @ 2023-07-24 11:17 UTC (permalink / raw)
  To: linux-kernel, devicetree, linux-arm-kernel
  Cc: conor+dt, krzysztof.kozlowski+dt, robh+dt, kristo, vigneshr, nm,
	u-kumar1, b-kapoor

CAN instances 3 and 5 in the main domain are brought on the common
processor board through header J27 and J28. The CAN High and Low lines
from the SoC are routed through a mux on the SoM. The select lines need
to be set for the CAN signals to get connected to the transceivers on
the common processor board. Threfore, add respective mux, transceiver
dt nodes to add support for these CAN instances.

Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
---

Changelog v4->v5 : Modfied Mux Controller names

Link to v4 : https://lore.kernel.org/all/0070e00a-89c0-9b2b-8753-e1835b5aad15@ti.com/

 .../dts/ti/k3-j721s2-common-proc-board.dts    | 46 +++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi  | 12 +++++
 2 files changed, 58 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index 04d4739d7245..e715fa12f9ca 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -29,6 +29,8 @@ aliases {
 		can0 = &main_mcan16;
 		can1 = &mcu_mcan0;
 		can2 = &mcu_mcan1;
+		can3 = &main_mcan3;
+		can4 = &main_mcan5;
 	};
 
 	evm_12v0: fixedregulator-evm12v0 {
@@ -109,6 +111,22 @@ transceiver2: can-phy2 {
 		standby-gpios = <&wkup_gpio0 2 GPIO_ACTIVE_HIGH>;
 	};
 
+	transceiver3: can-phy3 {
+		compatible = "ti,tcan1043";
+		#phy-cells = <0>;
+		max-bitrate = <5000000>;
+		standby-gpios = <&exp2 7 GPIO_ACTIVE_LOW>;
+		enable-gpios = <&exp2 6 GPIO_ACTIVE_HIGH>;
+		mux-states = <&mux0 1>;
+	};
+
+	transceiver4: can-phy4 {
+		compatible = "ti,tcan1042";
+		#phy-cells = <0>;
+		max-bitrate = <5000000>;
+		standby-gpios = <&exp_som 7 GPIO_ACTIVE_HIGH>;
+		mux-states = <&mux1 1>;
+	};
 };
 
 &main_pmx0 {
@@ -152,6 +170,20 @@ main_usbss0_pins_default: main-usbss0-default-pins {
 			J721S2_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AG25) TIMER_IO1.USB0_DRVVBUS */
 		>;
 	};
+
+	main_mcan3_pins_default: main-mcan3-pins-default {
+		pinctrl-single,pins = <
+			J721S2_IOPAD(0x080, PIN_INPUT, 0) /* (U26) MCASP0_AXR4.MCAN3_RX */
+			J721S2_IOPAD(0x07c, PIN_OUTPUT, 0) /* (T27) MCASP0_AXR3.MCAN3_TX */
+		>;
+	};
+
+	main_mcan5_pins_default: main-mcan5-pins-default {
+		pinctrl-single,pins = <
+			J721S2_IOPAD(0x03c, PIN_INPUT, 0) /* (U27) MCASP0_AFSX.MCAN5_RX */
+			J721S2_IOPAD(0x038, PIN_OUTPUT, 0) /* (AB28) MCASP0_ACLKX.MCAN5_TX */
+		>;
+	};
 };
 
 &wkup_pmx2 {
@@ -460,3 +492,17 @@ adc {
 		ti,adc-channels = <0 1 2 3 4 5 6 7>;
 	};
 };
+
+&main_mcan3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mcan3_pins_default>;
+	phys = <&transceiver3>;
+};
+
+&main_mcan5 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mcan5_pins_default>;
+	phys = <&transceiver4>;
+};
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
index d57dd43da0ef..594766482071 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
@@ -31,6 +31,18 @@ secure_ddr: optee@9e800000 {
 		};
 	};
 
+	mux0: mux-controller {
+		compatible = "gpio-mux";
+		#mux-state-cells = <1>;
+		mux-gpios = <&exp_som 1 GPIO_ACTIVE_HIGH>;
+	};
+
+	mux1: mux-controller {
+		compatible = "gpio-mux";
+		#mux-state-cells = <1>;
+		mux-gpios = <&exp_som 2 GPIO_ACTIVE_HIGH>;
+	};
+
 	transceiver0: can-phy0 {
 		/* standby pin has been grounded by default */
 		compatible = "ti,tcan1042";
-- 
2.34.1


^ permalink raw reply related	[flat|nested] 2+ messages in thread