From: "Jernej Škrabec" <jernej.skrabec@gmail.com> To: Maxime Ripard <mripard@kernel.org>, Chen-Yu Tsai <wens@csie.org>, Andre Przywara <andre.przywara@arm.com> Cc: Rob Herring <robh@kernel.org>, Icenowy Zheng <icenowy@aosc.io>, Samuel Holland <samuel@sholland.org>, Ondrej Jirman <megous@megous.com>, linux-arm-kernel@lists.infradead.org, linux-sunxi@googlegroups.com, linux-sunxi@lists.linux.dev, linux-kernel@vger.kernel.org, devicetree@vger.kernel.org Subject: Re: [PATCH v6 17/17] arm64: dts: allwinner: h616: Add X96 Mate TV box support Date: Sat, 22 May 2021 09:32:32 +0200 [thread overview] Message-ID: <2338288.Zx76mVtT47@kista> (raw) In-Reply-To: <20210519104152.21119-18-andre.przywara@arm.com> Hi Andre! Dne sreda, 19. maj 2021 ob 12:41:52 CEST je Andre Przywara napisal(a): > The X96 Mate is an Allwinner H616 based TV box, featuring: > - Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU > - 2GiB/4GiB RAM (fully usable!) > - 16/32/64GiB eMMC > - 100Mbps Ethernet (via embedded AC200 EPHY, not yet supported) > - Unsupported Allwinner WiFi chip > - 2 x USB 2.0 host ports > - HDMI port > - IR receiver > - 5V/2A DC power supply via barrel plug > > For more information see: https://linux-sunxi.org/X96_Mate > > Add a basic devicetree for it, with SD card, eMMC and USB working, as > well as serial and the essential peripherals, like the AXP PMIC. > > This DT is somewhat minimal, and should work on many other similar TV > boxes with the Allwinner H616 chip. > > Signed-off-by: Andre Przywara <andre.przywara@arm.com> > --- > arch/arm64/boot/dts/allwinner/Makefile | 1 + > .../dts/allwinner/sun50i-h616-x96-mate.dts | 201 ++++++++++++++++++ > 2 files changed, 202 insertions(+) > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts > > diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/ allwinner/Makefile > index 9ba4b5d92657..370d24ebaacf 100644 > --- a/arch/arm64/boot/dts/allwinner/Makefile > +++ b/arch/arm64/boot/dts/allwinner/Makefile > @@ -37,3 +37,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts b/arch/ arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts > new file mode 100644 > index 000000000000..b960bb310289 > --- /dev/null > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts > @@ -0,0 +1,201 @@ > +// SPDX-License-Identifier: (GPL-2.0+ or MIT) > +/* > + * Copyright (C) 2021 Arm Ltd. > + */ > + > +/dts-v1/; > + > +#include "sun50i-h616.dtsi" > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/interrupt-controller/arm-gic.h> > + > +/ { > + model = "X96 Mate"; > + compatible = "hechuang,x96-mate", "allwinner,sun50i-h616"; Please document compatible. Best regards, Jernej > + > + aliases { > + serial0 = &uart0; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + reg_vcc5v: vcc5v { > + /* board wide 5V supply directly from the DC input */ > + compatible = "regulator-fixed"; > + regulator-name = "vcc-5v"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + }; > +}; > + > +&ehci0 { > + status = "okay"; > +}; > + > +&ehci2 { > + status = "okay"; > +}; > + > +&ir { > + status = "okay"; > +}; > + > +&mmc0 { > + vmmc-supply = <®_dcdce>; > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ > + bus-width = <4>; > + status = "okay"; > +}; > + > +&mmc2 { > + vmmc-supply = <®_dcdce>; > + vqmmc-supply = <®_bldo1>; > + bus-width = <8>; > + non-removable; > + cap-mmc-hw-reset; > + mmc-hs200-1_8v; > + status = "okay"; > +}; > + > +&ohci0 { > + status = "okay"; > +}; > + > +&ohci2 { > + status = "okay"; > +}; > + > +&r_rsb { > + status = "okay"; > + > + axp305: pmic@745 { > + compatible = "x-powers,axp305", "x-powers,axp805", > + "x-powers,axp806"; > + interrupt-controller; > + #interrupt-cells = <1>; > + reg = <0x745>; > + > + x-powers,self-working-mode; > + vina-supply = <®_vcc5v>; > + vinb-supply = <®_vcc5v>; > + vinc-supply = <®_vcc5v>; > + vind-supply = <®_vcc5v>; > + vine-supply = <®_vcc5v>; > + aldoin-supply = <®_vcc5v>; > + bldoin-supply = <®_vcc5v>; > + cldoin-supply = <®_vcc5v>; > + > + regulators { > + reg_aldo1: aldo1 { > + regulator-always-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc-sys"; > + }; > + > + /* Enabled by the Android BSP */ > + reg_aldo2: aldo2 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc3v3-ext"; > + status = "disabled"; > + }; > + > + /* Enabled by the Android BSP */ > + reg_aldo3: aldo3 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc3v3-ext2"; > + status = "disabled"; > + }; > + > + reg_bldo1: bldo1 { > + regulator-always-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc1v8"; > + }; > + > + /* Enabled by the Android BSP */ > + reg_bldo2: bldo2 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc1v8-2"; > + status = "disabled"; > + }; > + > + bldo3 { > + /* unused */ > + }; > + > + bldo4 { > + /* unused */ > + }; > + > + cldo1 { > + regulator-min-microvolt = <2500000>; > + regulator-max-microvolt = <2500000>; > + regulator-name = "vcc2v5"; > + }; > + > + cldo2 { > + /* unused */ > + }; > + > + cldo3 { > + /* unused */ > + }; > + > + reg_dcdca: dcdca { > + regulator-always-on; > + regulator-min-microvolt = <810000>; > + regulator-max-microvolt = <1080000>; > + regulator-name = "vdd-cpu"; > + }; > + > + reg_dcdcc: dcdcc { > + regulator-always-on; > + regulator-min-microvolt = <810000>; > + regulator-max-microvolt = <1080000>; > + regulator-name = "vdd-gpu-sys"; > + }; > + > + reg_dcdcd: dcdcd { > + regulator-always-on; > + regulator-min-microvolt = <1360000>; > + regulator-max-microvolt = <1360000>; > + regulator-name = "vdd-dram"; > + }; > + > + reg_dcdce: dcdce { > + regulator-boot-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc-eth-mmc"; > + }; > + > + sw { > + /* unused */ > + }; > + }; > + }; > +}; > + > +&uart0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_ph_pins>; > + status = "okay"; > +}; > + > +&usbotg { > + dr_mode = "host"; /* USB A type receptable */ > + status = "okay"; > +}; > + > +&usbphy { > + status = "okay"; > +}; > -- > 2.17.5 > >
WARNING: multiple messages have this Message-ID (diff)
From: "Jernej Škrabec" <jernej.skrabec@gmail.com> To: Maxime Ripard <mripard@kernel.org>, Chen-Yu Tsai <wens@csie.org>, Andre Przywara <andre.przywara@arm.com> Cc: Rob Herring <robh@kernel.org>, Icenowy Zheng <icenowy@aosc.io>, Samuel Holland <samuel@sholland.org>, Ondrej Jirman <megous@megous.com>, linux-arm-kernel@lists.infradead.org, linux-sunxi@googlegroups.com, linux-sunxi@lists.linux.dev, linux-kernel@vger.kernel.org, devicetree@vger.kernel.org Subject: Re: [PATCH v6 17/17] arm64: dts: allwinner: h616: Add X96 Mate TV box support Date: Sat, 22 May 2021 09:32:32 +0200 [thread overview] Message-ID: <2338288.Zx76mVtT47@kista> (raw) In-Reply-To: <20210519104152.21119-18-andre.przywara@arm.com> Hi Andre! Dne sreda, 19. maj 2021 ob 12:41:52 CEST je Andre Przywara napisal(a): > The X96 Mate is an Allwinner H616 based TV box, featuring: > - Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU > - 2GiB/4GiB RAM (fully usable!) > - 16/32/64GiB eMMC > - 100Mbps Ethernet (via embedded AC200 EPHY, not yet supported) > - Unsupported Allwinner WiFi chip > - 2 x USB 2.0 host ports > - HDMI port > - IR receiver > - 5V/2A DC power supply via barrel plug > > For more information see: https://linux-sunxi.org/X96_Mate > > Add a basic devicetree for it, with SD card, eMMC and USB working, as > well as serial and the essential peripherals, like the AXP PMIC. > > This DT is somewhat minimal, and should work on many other similar TV > boxes with the Allwinner H616 chip. > > Signed-off-by: Andre Przywara <andre.przywara@arm.com> > --- > arch/arm64/boot/dts/allwinner/Makefile | 1 + > .../dts/allwinner/sun50i-h616-x96-mate.dts | 201 ++++++++++++++++++ > 2 files changed, 202 insertions(+) > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts > > diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/ allwinner/Makefile > index 9ba4b5d92657..370d24ebaacf 100644 > --- a/arch/arm64/boot/dts/allwinner/Makefile > +++ b/arch/arm64/boot/dts/allwinner/Makefile > @@ -37,3 +37,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts b/arch/ arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts > new file mode 100644 > index 000000000000..b960bb310289 > --- /dev/null > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts > @@ -0,0 +1,201 @@ > +// SPDX-License-Identifier: (GPL-2.0+ or MIT) > +/* > + * Copyright (C) 2021 Arm Ltd. > + */ > + > +/dts-v1/; > + > +#include "sun50i-h616.dtsi" > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/interrupt-controller/arm-gic.h> > + > +/ { > + model = "X96 Mate"; > + compatible = "hechuang,x96-mate", "allwinner,sun50i-h616"; Please document compatible. Best regards, Jernej > + > + aliases { > + serial0 = &uart0; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + reg_vcc5v: vcc5v { > + /* board wide 5V supply directly from the DC input */ > + compatible = "regulator-fixed"; > + regulator-name = "vcc-5v"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + }; > +}; > + > +&ehci0 { > + status = "okay"; > +}; > + > +&ehci2 { > + status = "okay"; > +}; > + > +&ir { > + status = "okay"; > +}; > + > +&mmc0 { > + vmmc-supply = <®_dcdce>; > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ > + bus-width = <4>; > + status = "okay"; > +}; > + > +&mmc2 { > + vmmc-supply = <®_dcdce>; > + vqmmc-supply = <®_bldo1>; > + bus-width = <8>; > + non-removable; > + cap-mmc-hw-reset; > + mmc-hs200-1_8v; > + status = "okay"; > +}; > + > +&ohci0 { > + status = "okay"; > +}; > + > +&ohci2 { > + status = "okay"; > +}; > + > +&r_rsb { > + status = "okay"; > + > + axp305: pmic@745 { > + compatible = "x-powers,axp305", "x-powers,axp805", > + "x-powers,axp806"; > + interrupt-controller; > + #interrupt-cells = <1>; > + reg = <0x745>; > + > + x-powers,self-working-mode; > + vina-supply = <®_vcc5v>; > + vinb-supply = <®_vcc5v>; > + vinc-supply = <®_vcc5v>; > + vind-supply = <®_vcc5v>; > + vine-supply = <®_vcc5v>; > + aldoin-supply = <®_vcc5v>; > + bldoin-supply = <®_vcc5v>; > + cldoin-supply = <®_vcc5v>; > + > + regulators { > + reg_aldo1: aldo1 { > + regulator-always-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc-sys"; > + }; > + > + /* Enabled by the Android BSP */ > + reg_aldo2: aldo2 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc3v3-ext"; > + status = "disabled"; > + }; > + > + /* Enabled by the Android BSP */ > + reg_aldo3: aldo3 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc3v3-ext2"; > + status = "disabled"; > + }; > + > + reg_bldo1: bldo1 { > + regulator-always-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc1v8"; > + }; > + > + /* Enabled by the Android BSP */ > + reg_bldo2: bldo2 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc1v8-2"; > + status = "disabled"; > + }; > + > + bldo3 { > + /* unused */ > + }; > + > + bldo4 { > + /* unused */ > + }; > + > + cldo1 { > + regulator-min-microvolt = <2500000>; > + regulator-max-microvolt = <2500000>; > + regulator-name = "vcc2v5"; > + }; > + > + cldo2 { > + /* unused */ > + }; > + > + cldo3 { > + /* unused */ > + }; > + > + reg_dcdca: dcdca { > + regulator-always-on; > + regulator-min-microvolt = <810000>; > + regulator-max-microvolt = <1080000>; > + regulator-name = "vdd-cpu"; > + }; > + > + reg_dcdcc: dcdcc { > + regulator-always-on; > + regulator-min-microvolt = <810000>; > + regulator-max-microvolt = <1080000>; > + regulator-name = "vdd-gpu-sys"; > + }; > + > + reg_dcdcd: dcdcd { > + regulator-always-on; > + regulator-min-microvolt = <1360000>; > + regulator-max-microvolt = <1360000>; > + regulator-name = "vdd-dram"; > + }; > + > + reg_dcdce: dcdce { > + regulator-boot-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc-eth-mmc"; > + }; > + > + sw { > + /* unused */ > + }; > + }; > + }; > +}; > + > +&uart0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_ph_pins>; > + status = "okay"; > +}; > + > +&usbotg { > + dr_mode = "host"; /* USB A type receptable */ > + status = "okay"; > +}; > + > +&usbphy { > + status = "okay"; > +}; > -- > 2.17.5 > > _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-05-22 7:32 UTC|newest] Thread overview: 104+ messages / expand[flat|nested] mbox.gz Atom feed top 2021-05-19 10:41 [PATCH v6 00/17] arm64: sunxi: Initial Allwinner H616 SoC support Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-19 10:41 ` [PATCH v6 01/17] dt-bindings: mfd: axp20x: Add AXP305 compatible (plus optional IRQ) Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-21 1:39 ` Rob Herring 2021-05-21 1:39 ` Rob Herring 2021-05-22 14:46 ` Samuel Holland 2021-05-22 14:46 ` Samuel Holland 2021-05-23 0:01 ` Andre Przywara 2021-05-23 0:01 ` Andre Przywara 2021-05-19 10:41 ` [PATCH v6 02/17] mfd: axp20x: Allow AXP 806 chips without interrupt lines Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-19 15:01 ` Lee Jones 2021-05-19 15:01 ` Lee Jones 2021-05-19 10:41 ` [PATCH v6 03/17] dt-bindings: rtc: sun6i: Add H616 compatible string Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-21 1:39 ` Rob Herring 2021-05-21 1:39 ` Rob Herring 2021-05-21 2:37 ` Samuel Holland 2021-05-21 2:37 ` Samuel Holland 2021-06-07 12:59 ` Andre Przywara 2021-06-07 12:59 ` Andre Przywara 2021-06-08 4:23 ` Samuel Holland 2021-06-08 4:23 ` Samuel Holland 2021-06-15 12:24 ` Andre Przywara 2021-06-15 12:24 ` Andre Przywara 2021-06-16 9:07 ` Maxime Ripard 2021-06-16 9:07 ` Maxime Ripard 2021-06-16 11:28 ` Andre Przywara 2021-06-16 11:28 ` Andre Przywara 2021-05-19 10:41 ` [PATCH v6 04/17] rtc: sun6i: Add support for linear day storage Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-22 7:26 ` Jernej Škrabec 2021-05-22 7:26 ` Jernej Škrabec 2021-05-19 10:41 ` [PATCH v6 05/17] rtc: sun6i: Add Allwinner H616 support Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-22 7:29 ` Jernej Škrabec 2021-05-22 7:29 ` Jernej Škrabec 2021-05-23 0:06 ` Andre Przywara 2021-05-23 0:06 ` Andre Przywara 2021-05-19 10:41 ` [PATCH v6 06/17] dt-bindings: net: sun8i-emac: Add H616 compatible string Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-21 1:40 ` Rob Herring 2021-05-21 1:40 ` Rob Herring 2021-05-19 10:41 ` [PATCH v6 07/17] net: stmmac: dwmac-sun8i: Prepare for second EMAC clock register Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-19 10:41 ` [PATCH v6 08/17] dt-bindings: usb: Add H616 compatible string Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-21 1:40 ` Rob Herring 2021-05-21 1:40 ` Rob Herring 2021-05-21 1:40 ` Rob Herring 2021-05-19 10:41 ` [PATCH v6 09/17] dt-bindings: usb: sunxi-musb: " Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-21 1:40 ` Rob Herring 2021-05-21 1:40 ` Rob Herring 2021-05-19 10:41 ` [PATCH v6 10/17] phy: sun4i-usb: Rework HCI PHY (aka. "pmu_unk1") handling Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-19 10:41 ` [PATCH v6 11/17] phy: sun4i-usb: Allow reset line to be shared Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-19 10:41 ` [PATCH v6 12/17] phy: sun4i-usb: Introduce port2 SIDDQ quirk Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-24 11:59 ` Maxime Ripard 2021-05-24 11:59 ` Maxime Ripard 2021-05-24 11:59 ` Maxime Ripard 2021-05-24 12:51 ` Jernej Škrabec 2021-05-24 12:51 ` Jernej Škrabec 2021-05-24 12:51 ` Jernej Škrabec 2021-05-25 11:29 ` Andre Przywara 2021-05-25 11:29 ` Andre Przywara 2021-05-25 11:29 ` Andre Przywara 2021-06-07 13:22 ` Maxime Ripard 2021-06-07 13:22 ` Maxime Ripard 2021-06-07 13:22 ` Maxime Ripard 2021-06-07 14:17 ` Andre Przywara 2021-06-07 14:17 ` Andre Przywara 2021-06-07 14:17 ` Andre Przywara 2021-06-07 14:26 ` [linux-sunxi] " Chen-Yu Tsai 2021-06-07 14:26 ` Chen-Yu Tsai 2021-06-07 14:26 ` Chen-Yu Tsai 2021-06-07 14:26 ` Chen-Yu Tsai 2021-06-14 0:20 ` Andre Przywara 2021-06-14 0:20 ` Andre Przywara 2021-06-14 0:20 ` Andre Przywara 2021-05-19 10:41 ` [PATCH v6 13/17] phy: sun4i-usb: Add support for the H616 USB PHY Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-19 10:41 ` [PATCH v6 14/17] arm64: dts: allwinner: Add Allwinner H616 .dtsi file Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-24 12:02 ` Maxime Ripard 2021-05-24 12:02 ` Maxime Ripard 2021-06-07 12:59 ` Andre Przywara 2021-06-07 12:59 ` Andre Przywara 2021-05-19 10:41 ` [PATCH v6 15/17] dt-bindings: arm: sunxi: Add OrangePi Zero 2 binding Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-19 10:41 ` [PATCH v6 16/17] arm64: dts: allwinner: h616: Add OrangePi Zero 2 board support Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-19 10:41 ` [PATCH v6 17/17] arm64: dts: allwinner: h616: Add X96 Mate TV box support Andre Przywara 2021-05-19 10:41 ` Andre Przywara 2021-05-22 7:32 ` Jernej Škrabec [this message] 2021-05-22 7:32 ` Jernej Škrabec
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=2338288.Zx76mVtT47@kista \ --to=jernej.skrabec@gmail.com \ --cc=andre.przywara@arm.com \ --cc=devicetree@vger.kernel.org \ --cc=icenowy@aosc.io \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-sunxi@googlegroups.com \ --cc=linux-sunxi@lists.linux.dev \ --cc=megous@megous.com \ --cc=mripard@kernel.org \ --cc=robh@kernel.org \ --cc=samuel@sholland.org \ --cc=wens@csie.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.