From: Heiko Stuebner <heiko@sntech.de> To: djw@t-chip.com.cn Cc: linux-rockchip@lists.infradead.org, Wayne Chou <zxf@t-chip.com.cn>, devicetree@vger.kernel.org, David Wu <david.wu@rock-chips.com>, Liang Chen <cl@rock-chips.com>, linux-kernel@vger.kernel.org, Rob Herring <robh+dt@kernel.org>, Rocky Hao <rocky.hao@rock-chips.com>, Will Deacon <will.deacon@arm.com>, Joseph Chen <chenjh@rock-chips.com>, Mark Rutland <mark.rutland@arm.com>, Catalin Marinas <catalin.marinas@arm.com>, linux-arm-kernel@lists.infradead.org Subject: Re: [PATCH v4 4/4] arm64: dts: rockchip: add sdmmc UHS support for roc-rk3328-cc Date: Sat, 04 Aug 2018 15:18:32 +0200 [thread overview] Message-ID: <3379811.jaOMd9KUxU@phil> (raw) In-Reply-To: <1533016762-5268-5-git-send-email-djw@t-chip.com.cn> Hi Levin, Am Dienstag, 31. Juli 2018, 07:59:22 CEST schrieb djw@t-chip.com.cn: > From: Levin Du <djw@t-chip.com.cn> > > In roc-rk3328-cc board, the signal voltage of sdmmc is supplied by the > vcc_sdio regulator, which is a mux between 1.8V and 3.3V, controlled by > a special output only gpio pin labeled "gpiomut_pmuio_iout", > corresponding bit 1 of the syscon GRF_SOC_CON10. > > This special pin can now be reference as <&grf_gpio 0>, thanks to the > gpio-syscon driver, which makes writing regulator-gpio possible. > > If the signal voltage changes, the io domain needs to change > correspondingly. > > To use this feature, the following options are required in kernel config: > - CONFIG_GPIO_SYSCON=y > - CONFIG_POWER_AVS=y > - CONFIG_ROCKCHIP_IODOMAIN=y > > Signed-off-by: Levin Du <djw@t-chip.com.cn> [...] > @@ -277,3 +295,7 @@ > &usb_host0_ohci { > status = "okay"; > }; > + > +&grf_gpio { > + status = "okay"; > +}; > applied to my dts64 branch after dropping the grf_gpio enablement, see comment in patch2 regarding the always present pin. Thanks Heiko
WARNING: multiple messages have this Message-ID (diff)
From: heiko@sntech.de (Heiko Stuebner) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH v4 4/4] arm64: dts: rockchip: add sdmmc UHS support for roc-rk3328-cc Date: Sat, 04 Aug 2018 15:18:32 +0200 [thread overview] Message-ID: <3379811.jaOMd9KUxU@phil> (raw) In-Reply-To: <1533016762-5268-5-git-send-email-djw@t-chip.com.cn> Hi Levin, Am Dienstag, 31. Juli 2018, 07:59:22 CEST schrieb djw at t-chip.com.cn: > From: Levin Du <djw@t-chip.com.cn> > > In roc-rk3328-cc board, the signal voltage of sdmmc is supplied by the > vcc_sdio regulator, which is a mux between 1.8V and 3.3V, controlled by > a special output only gpio pin labeled "gpiomut_pmuio_iout", > corresponding bit 1 of the syscon GRF_SOC_CON10. > > This special pin can now be reference as <&grf_gpio 0>, thanks to the > gpio-syscon driver, which makes writing regulator-gpio possible. > > If the signal voltage changes, the io domain needs to change > correspondingly. > > To use this feature, the following options are required in kernel config: > - CONFIG_GPIO_SYSCON=y > - CONFIG_POWER_AVS=y > - CONFIG_ROCKCHIP_IODOMAIN=y > > Signed-off-by: Levin Du <djw@t-chip.com.cn> [...] > @@ -277,3 +295,7 @@ > &usb_host0_ohci { > status = "okay"; > }; > + > +&grf_gpio { > + status = "okay"; > +}; > applied to my dts64 branch after dropping the grf_gpio enablement, see comment in patch2 regarding the always present pin. Thanks Heiko
next prev parent reply other threads:[~2018-08-04 13:18 UTC|newest] Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top 2018-07-31 5:59 [PATCH v4 0/4] Add sdmmc UHS support to ROC-RK3328-CC board djw 2018-07-31 5:59 ` djw at t-chip.com.cn 2018-07-31 5:59 ` djw 2018-07-31 5:59 ` [PATCH v4 1/4] gpio: syscon: rockchip: add GRF GPIO support for rk3328 djw 2018-07-31 5:59 ` djw at t-chip.com.cn 2018-07-31 19:36 ` Rob Herring 2018-07-31 19:36 ` Rob Herring 2018-08-01 11:46 ` Heiko Stuebner 2018-08-01 11:46 ` Heiko Stuebner 2018-08-03 17:13 ` Linus Walleij 2018-08-03 17:13 ` Linus Walleij 2018-07-31 5:59 ` [PATCH v4 2/4] arm64: dts: rockchip: add GRF GPIO controller to rk3328 djw 2018-07-31 5:59 ` djw at t-chip.com.cn 2018-08-04 13:16 ` Heiko Stuebner 2018-08-04 13:16 ` Heiko Stuebner 2018-07-31 5:59 ` [PATCH v4 3/4] arm64: dts: rockchip: add io-domain to roc-rk3328-cc djw 2018-07-31 5:59 ` djw at t-chip.com.cn 2018-08-02 12:54 ` Heiko Stuebner 2018-08-02 12:54 ` Heiko Stuebner 2018-07-31 5:59 ` [PATCH v4 4/4] arm64: dts: rockchip: add sdmmc UHS support for roc-rk3328-cc djw 2018-07-31 5:59 ` djw at t-chip.com.cn 2018-08-04 13:18 ` Heiko Stuebner [this message] 2018-08-04 13:18 ` Heiko Stuebner
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=3379811.jaOMd9KUxU@phil \ --to=heiko@sntech.de \ --cc=catalin.marinas@arm.com \ --cc=chenjh@rock-chips.com \ --cc=cl@rock-chips.com \ --cc=david.wu@rock-chips.com \ --cc=devicetree@vger.kernel.org \ --cc=djw@t-chip.com.cn \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-rockchip@lists.infradead.org \ --cc=mark.rutland@arm.com \ --cc=robh+dt@kernel.org \ --cc=rocky.hao@rock-chips.com \ --cc=will.deacon@arm.com \ --cc=zxf@t-chip.com.cn \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.