* [PATCH 0/3] Add Avenger96 board support @ 2019-05-03 5:31 ` Manivannan Sadhasivam 0 siblings, 0 replies; 18+ messages in thread From: Manivannan Sadhasivam @ 2019-05-03 5:31 UTC (permalink / raw) To: mcoquelin.stm32, alexandre.torgue, robh+dt Cc: linux-stm32, linux-arm-kernel, devicetree, linux-kernel, loic.pallardy, Manivannan Sadhasivam Hello, This patchset adds Avenger96 board support. This board is one of the Consumer Edition boards of the 96Boards family from Arrow Electronics featuring STM32MP157A MPU and has the following features: SoC: STM32MP157AAC PMIC: STPMIC1A RAM: 1024 Mbyte @ 533MHz Storage: eMMC v4.51: 8 Gbyte microSD Socket: UHS-1 v3.01 Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac Bluetooth®v4.2 (BR/EDR/BLE) USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4 LED: 4x User LED, 1x WiFi LED, 1x BT LED More information about this board can be found in 96Boards website: https://www.96boards.org/product/avenger96/ Thanks, Mani Manivannan Sadhasivam (3): dt-bindings: arm: stm32: Document Avenger96 devicetree binding ARM: dts: stm32mp157: Add missing pinctrl definitions ARM: dts: Add Avenger96 devicetree support based on STM32MP157A .../devicetree/bindings/arm/stm32/stm32.txt | 6 + arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 62 ++++ arch/arm/boot/dts/stm32mp157a-avenger96.dts | 320 ++++++++++++++++++ 4 files changed, 389 insertions(+) create mode 100644 arch/arm/boot/dts/stm32mp157a-avenger96.dts -- 2.17.1 ^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH 0/3] Add Avenger96 board support @ 2019-05-03 5:31 ` Manivannan Sadhasivam 0 siblings, 0 replies; 18+ messages in thread From: Manivannan Sadhasivam @ 2019-05-03 5:31 UTC (permalink / raw) To: mcoquelin.stm32, alexandre.torgue, robh+dt Cc: devicetree, loic.pallardy, linux-kernel, Manivannan Sadhasivam, linux-stm32, linux-arm-kernel Hello, This patchset adds Avenger96 board support. This board is one of the Consumer Edition boards of the 96Boards family from Arrow Electronics featuring STM32MP157A MPU and has the following features: SoC: STM32MP157AAC PMIC: STPMIC1A RAM: 1024 Mbyte @ 533MHz Storage: eMMC v4.51: 8 Gbyte microSD Socket: UHS-1 v3.01 Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac Bluetooth®v4.2 (BR/EDR/BLE) USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4 LED: 4x User LED, 1x WiFi LED, 1x BT LED More information about this board can be found in 96Boards website: https://www.96boards.org/product/avenger96/ Thanks, Mani Manivannan Sadhasivam (3): dt-bindings: arm: stm32: Document Avenger96 devicetree binding ARM: dts: stm32mp157: Add missing pinctrl definitions ARM: dts: Add Avenger96 devicetree support based on STM32MP157A .../devicetree/bindings/arm/stm32/stm32.txt | 6 + arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 62 ++++ arch/arm/boot/dts/stm32mp157a-avenger96.dts | 320 ++++++++++++++++++ 4 files changed, 389 insertions(+) create mode 100644 arch/arm/boot/dts/stm32mp157a-avenger96.dts -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH 1/3] dt-bindings: arm: stm32: Document Avenger96 devicetree binding 2019-05-03 5:31 ` Manivannan Sadhasivam @ 2019-05-03 5:31 ` Manivannan Sadhasivam -1 siblings, 0 replies; 18+ messages in thread From: Manivannan Sadhasivam @ 2019-05-03 5:31 UTC (permalink / raw) To: mcoquelin.stm32, alexandre.torgue, robh+dt Cc: linux-stm32, linux-arm-kernel, devicetree, linux-kernel, loic.pallardy, Manivannan Sadhasivam Document devicetree binding for Avenger96 board. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> --- Documentation/devicetree/bindings/arm/stm32/stm32.txt | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/stm32/stm32.txt b/Documentation/devicetree/bindings/arm/stm32/stm32.txt index 6808ed9ddfd5..eba363a4b514 100644 --- a/Documentation/devicetree/bindings/arm/stm32/stm32.txt +++ b/Documentation/devicetree/bindings/arm/stm32/stm32.txt @@ -8,3 +8,9 @@ using one of the following compatible strings: st,stm32f746 st,stm32h743 st,stm32mp157 + +Boards: + +Root node property compatible must contain one of below depending on board: + + - Avenger96: "arrow,stm32mp157a-avenger96" -- 2.17.1 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH 1/3] dt-bindings: arm: stm32: Document Avenger96 devicetree binding @ 2019-05-03 5:31 ` Manivannan Sadhasivam 0 siblings, 0 replies; 18+ messages in thread From: Manivannan Sadhasivam @ 2019-05-03 5:31 UTC (permalink / raw) To: mcoquelin.stm32, alexandre.torgue, robh+dt Cc: devicetree, loic.pallardy, linux-kernel, Manivannan Sadhasivam, linux-stm32, linux-arm-kernel Document devicetree binding for Avenger96 board. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> --- Documentation/devicetree/bindings/arm/stm32/stm32.txt | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/stm32/stm32.txt b/Documentation/devicetree/bindings/arm/stm32/stm32.txt index 6808ed9ddfd5..eba363a4b514 100644 --- a/Documentation/devicetree/bindings/arm/stm32/stm32.txt +++ b/Documentation/devicetree/bindings/arm/stm32/stm32.txt @@ -8,3 +8,9 @@ using one of the following compatible strings: st,stm32f746 st,stm32h743 st,stm32mp157 + +Boards: + +Root node property compatible must contain one of below depending on board: + + - Avenger96: "arrow,stm32mp157a-avenger96" -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH 2/3] ARM: dts: stm32mp157: Add missing pinctrl definitions 2019-05-03 5:31 ` Manivannan Sadhasivam @ 2019-05-03 5:31 ` Manivannan Sadhasivam -1 siblings, 0 replies; 18+ messages in thread From: Manivannan Sadhasivam @ 2019-05-03 5:31 UTC (permalink / raw) To: mcoquelin.stm32, alexandre.torgue, robh+dt Cc: linux-stm32, linux-arm-kernel, devicetree, linux-kernel, loic.pallardy, Manivannan Sadhasivam Add missing pinctrl definitions for STM32MP157 MPU. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> --- arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 62 +++++++++++++++++++++++ 1 file changed, 62 insertions(+) diff --git a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi index 85c417d9983b..0b5bcf6a7c97 100644 --- a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi +++ b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi @@ -241,6 +241,23 @@ }; }; + i2c1_pins_b: i2c1-2 { + pins { + pinmux = <STM32_PINMUX('F', 14, AF5)>, /* I2C1_SCL */ + <STM32_PINMUX('F', 15, AF5)>; /* I2C1_SDA */ + bias-disable; + drive-open-drain; + slew-rate = <0>; + }; + }; + + i2c1_pins_sleep_b: i2c1-3 { + pins { + pinmux = <STM32_PINMUX('F', 14, ANALOG)>, /* I2C1_SCL */ + <STM32_PINMUX('F', 15, ANALOG)>; /* I2C1_SDA */ + }; + }; + i2c2_pins_a: i2c2-0 { pins { pinmux = <STM32_PINMUX('H', 4, AF4)>, /* I2C2_SCL */ @@ -258,6 +275,23 @@ }; }; + i2c2_pins_b: i2c2-2 { + pins { + pinmux = <STM32_PINMUX('Z', 0, AF3)>, /* I2C2_SCL */ + <STM32_PINMUX('H', 5, AF4)>; /* I2C2_SDA */ + bias-disable; + drive-open-drain; + slew-rate = <0>; + }; + }; + + i2c2_pins_sleep_b: i2c2-3 { + pins { + pinmux = <STM32_PINMUX('Z', 0, ANALOG)>, /* I2C2_SCL */ + <STM32_PINMUX('H', 5, ANALOG)>; /* I2C2_SDA */ + }; + }; + i2c5_pins_a: i2c5-0 { pins { pinmux = <STM32_PINMUX('A', 11, AF4)>, /* I2C5_SCL */ @@ -599,6 +633,34 @@ bias-disable; }; }; + + uart4_pins_b: uart4-1 { + pins1 { + pinmux = <STM32_PINMUX('D', 1, AF8)>; /* UART4_TX */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */ + bias-disable; + }; + }; + + uart7_pins_a: uart7-0 { + pins1 { + pinmux = <STM32_PINMUX('E', 8, AF7)>; /* UART4_TX */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32_PINMUX('E', 7, AF7)>, /* UART4_RX */ + <STM32_PINMUX('E', 10, AF7)>, /* UART4_CTS */ + <STM32_PINMUX('E', 9, AF7)>; /* UART4_RTS */ + bias-disable; + }; + }; }; pinctrl_z: pin-controller-z@54004000 { -- 2.17.1 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH 2/3] ARM: dts: stm32mp157: Add missing pinctrl definitions @ 2019-05-03 5:31 ` Manivannan Sadhasivam 0 siblings, 0 replies; 18+ messages in thread From: Manivannan Sadhasivam @ 2019-05-03 5:31 UTC (permalink / raw) To: mcoquelin.stm32, alexandre.torgue, robh+dt Cc: devicetree, loic.pallardy, linux-kernel, Manivannan Sadhasivam, linux-stm32, linux-arm-kernel Add missing pinctrl definitions for STM32MP157 MPU. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> --- arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 62 +++++++++++++++++++++++ 1 file changed, 62 insertions(+) diff --git a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi index 85c417d9983b..0b5bcf6a7c97 100644 --- a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi +++ b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi @@ -241,6 +241,23 @@ }; }; + i2c1_pins_b: i2c1-2 { + pins { + pinmux = <STM32_PINMUX('F', 14, AF5)>, /* I2C1_SCL */ + <STM32_PINMUX('F', 15, AF5)>; /* I2C1_SDA */ + bias-disable; + drive-open-drain; + slew-rate = <0>; + }; + }; + + i2c1_pins_sleep_b: i2c1-3 { + pins { + pinmux = <STM32_PINMUX('F', 14, ANALOG)>, /* I2C1_SCL */ + <STM32_PINMUX('F', 15, ANALOG)>; /* I2C1_SDA */ + }; + }; + i2c2_pins_a: i2c2-0 { pins { pinmux = <STM32_PINMUX('H', 4, AF4)>, /* I2C2_SCL */ @@ -258,6 +275,23 @@ }; }; + i2c2_pins_b: i2c2-2 { + pins { + pinmux = <STM32_PINMUX('Z', 0, AF3)>, /* I2C2_SCL */ + <STM32_PINMUX('H', 5, AF4)>; /* I2C2_SDA */ + bias-disable; + drive-open-drain; + slew-rate = <0>; + }; + }; + + i2c2_pins_sleep_b: i2c2-3 { + pins { + pinmux = <STM32_PINMUX('Z', 0, ANALOG)>, /* I2C2_SCL */ + <STM32_PINMUX('H', 5, ANALOG)>; /* I2C2_SDA */ + }; + }; + i2c5_pins_a: i2c5-0 { pins { pinmux = <STM32_PINMUX('A', 11, AF4)>, /* I2C5_SCL */ @@ -599,6 +633,34 @@ bias-disable; }; }; + + uart4_pins_b: uart4-1 { + pins1 { + pinmux = <STM32_PINMUX('D', 1, AF8)>; /* UART4_TX */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */ + bias-disable; + }; + }; + + uart7_pins_a: uart7-0 { + pins1 { + pinmux = <STM32_PINMUX('E', 8, AF7)>; /* UART4_TX */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32_PINMUX('E', 7, AF7)>, /* UART4_RX */ + <STM32_PINMUX('E', 10, AF7)>, /* UART4_CTS */ + <STM32_PINMUX('E', 9, AF7)>; /* UART4_RTS */ + bias-disable; + }; + }; }; pinctrl_z: pin-controller-z@54004000 { -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 18+ messages in thread
* Re: [PATCH 2/3] ARM: dts: stm32mp157: Add missing pinctrl definitions 2019-05-03 5:31 ` Manivannan Sadhasivam (?) @ 2019-05-03 7:13 ` Alexandre Torgue -1 siblings, 0 replies; 18+ messages in thread From: Alexandre Torgue @ 2019-05-03 7:13 UTC (permalink / raw) To: Manivannan Sadhasivam, mcoquelin.stm32, robh+dt Cc: linux-stm32, linux-arm-kernel, devicetree, linux-kernel, loic.pallardy Hi Mani On 5/3/19 7:31 AM, Manivannan Sadhasivam wrote: > Add missing pinctrl definitions for STM32MP157 MPU. > > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > --- > arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 62 +++++++++++++++++++++++ > 1 file changed, 62 insertions(+) > > diff --git a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi > index 85c417d9983b..0b5bcf6a7c97 100644 > --- a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi > +++ b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi > @@ -241,6 +241,23 @@ > }; > }; > > + i2c1_pins_b: i2c1-2 { > + pins { > + pinmux = <STM32_PINMUX('F', 14, AF5)>, /* I2C1_SCL */ > + <STM32_PINMUX('F', 15, AF5)>; /* I2C1_SDA */ > + bias-disable; > + drive-open-drain; > + slew-rate = <0>; > + }; > + }; > + > + i2c1_pins_sleep_b: i2c1-3 { > + pins { > + pinmux = <STM32_PINMUX('F', 14, ANALOG)>, /* I2C1_SCL */ > + <STM32_PINMUX('F', 15, ANALOG)>; /* I2C1_SDA */ > + }; > + }; > + > i2c2_pins_a: i2c2-0 { > pins { > pinmux = <STM32_PINMUX('H', 4, AF4)>, /* I2C2_SCL */ > @@ -258,6 +275,23 @@ > }; > }; > > + i2c2_pins_b: i2c2-2 { > + pins { > + pinmux = <STM32_PINMUX('Z', 0, AF3)>, /* I2C2_SCL */ > + <STM32_PINMUX('H', 5, AF4)>; /* I2C2_SDA */ You can't do that. <STM32_PINMUX('Z', 0, AF3)> has to be declared in pincontroller-z. So in your case, you have to define 2 groups for i2C2 for your default state (the same for the sleep state). regards Alex > + bias-disable; > + drive-open-drain; > + slew-rate = <0>; > + }; > + }; > + > + i2c2_pins_sleep_b: i2c2-3 { > + pins { > + pinmux = <STM32_PINMUX('Z', 0, ANALOG)>, /* I2C2_SCL */ > + <STM32_PINMUX('H', 5, ANALOG)>; /* I2C2_SDA */ > + }; > + }; > + > i2c5_pins_a: i2c5-0 { > pins { > pinmux = <STM32_PINMUX('A', 11, AF4)>, /* I2C5_SCL */ > @@ -599,6 +633,34 @@ > bias-disable; > }; > }; > + > + uart4_pins_b: uart4-1 { > + pins1 { > + pinmux = <STM32_PINMUX('D', 1, AF8)>; /* UART4_TX */ > + bias-disable; > + drive-push-pull; > + slew-rate = <0>; > + }; > + pins2 { > + pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */ > + bias-disable; > + }; > + }; > + > + uart7_pins_a: uart7-0 { > + pins1 { > + pinmux = <STM32_PINMUX('E', 8, AF7)>; /* UART4_TX */ > + bias-disable; > + drive-push-pull; > + slew-rate = <0>; > + }; > + pins2 { > + pinmux = <STM32_PINMUX('E', 7, AF7)>, /* UART4_RX */ > + <STM32_PINMUX('E', 10, AF7)>, /* UART4_CTS */ > + <STM32_PINMUX('E', 9, AF7)>; /* UART4_RTS */ > + bias-disable; > + }; > + }; > }; > > pinctrl_z: pin-controller-z@54004000 { > ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 2/3] ARM: dts: stm32mp157: Add missing pinctrl definitions @ 2019-05-03 7:13 ` Alexandre Torgue 0 siblings, 0 replies; 18+ messages in thread From: Alexandre Torgue @ 2019-05-03 7:13 UTC (permalink / raw) To: Manivannan Sadhasivam, mcoquelin.stm32, robh+dt Cc: devicetree, loic.pallardy, linux-stm32, linux-arm-kernel, linux-kernel Hi Mani On 5/3/19 7:31 AM, Manivannan Sadhasivam wrote: > Add missing pinctrl definitions for STM32MP157 MPU. > > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > --- > arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 62 +++++++++++++++++++++++ > 1 file changed, 62 insertions(+) > > diff --git a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi > index 85c417d9983b..0b5bcf6a7c97 100644 > --- a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi > +++ b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi > @@ -241,6 +241,23 @@ > }; > }; > > + i2c1_pins_b: i2c1-2 { > + pins { > + pinmux = <STM32_PINMUX('F', 14, AF5)>, /* I2C1_SCL */ > + <STM32_PINMUX('F', 15, AF5)>; /* I2C1_SDA */ > + bias-disable; > + drive-open-drain; > + slew-rate = <0>; > + }; > + }; > + > + i2c1_pins_sleep_b: i2c1-3 { > + pins { > + pinmux = <STM32_PINMUX('F', 14, ANALOG)>, /* I2C1_SCL */ > + <STM32_PINMUX('F', 15, ANALOG)>; /* I2C1_SDA */ > + }; > + }; > + > i2c2_pins_a: i2c2-0 { > pins { > pinmux = <STM32_PINMUX('H', 4, AF4)>, /* I2C2_SCL */ > @@ -258,6 +275,23 @@ > }; > }; > > + i2c2_pins_b: i2c2-2 { > + pins { > + pinmux = <STM32_PINMUX('Z', 0, AF3)>, /* I2C2_SCL */ > + <STM32_PINMUX('H', 5, AF4)>; /* I2C2_SDA */ You can't do that. <STM32_PINMUX('Z', 0, AF3)> has to be declared in pincontroller-z. So in your case, you have to define 2 groups for i2C2 for your default state (the same for the sleep state). regards Alex > + bias-disable; > + drive-open-drain; > + slew-rate = <0>; > + }; > + }; > + > + i2c2_pins_sleep_b: i2c2-3 { > + pins { > + pinmux = <STM32_PINMUX('Z', 0, ANALOG)>, /* I2C2_SCL */ > + <STM32_PINMUX('H', 5, ANALOG)>; /* I2C2_SDA */ > + }; > + }; > + > i2c5_pins_a: i2c5-0 { > pins { > pinmux = <STM32_PINMUX('A', 11, AF4)>, /* I2C5_SCL */ > @@ -599,6 +633,34 @@ > bias-disable; > }; > }; > + > + uart4_pins_b: uart4-1 { > + pins1 { > + pinmux = <STM32_PINMUX('D', 1, AF8)>; /* UART4_TX */ > + bias-disable; > + drive-push-pull; > + slew-rate = <0>; > + }; > + pins2 { > + pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */ > + bias-disable; > + }; > + }; > + > + uart7_pins_a: uart7-0 { > + pins1 { > + pinmux = <STM32_PINMUX('E', 8, AF7)>; /* UART4_TX */ > + bias-disable; > + drive-push-pull; > + slew-rate = <0>; > + }; > + pins2 { > + pinmux = <STM32_PINMUX('E', 7, AF7)>, /* UART4_RX */ > + <STM32_PINMUX('E', 10, AF7)>, /* UART4_CTS */ > + <STM32_PINMUX('E', 9, AF7)>; /* UART4_RTS */ > + bias-disable; > + }; > + }; > }; > > pinctrl_z: pin-controller-z@54004000 { > _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 2/3] ARM: dts: stm32mp157: Add missing pinctrl definitions @ 2019-05-03 7:13 ` Alexandre Torgue 0 siblings, 0 replies; 18+ messages in thread From: Alexandre Torgue @ 2019-05-03 7:13 UTC (permalink / raw) To: Manivannan Sadhasivam, mcoquelin.stm32, robh+dt Cc: linux-stm32, linux-arm-kernel, devicetree, linux-kernel, loic.pallardy Hi Mani On 5/3/19 7:31 AM, Manivannan Sadhasivam wrote: > Add missing pinctrl definitions for STM32MP157 MPU. > > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > --- > arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 62 +++++++++++++++++++++++ > 1 file changed, 62 insertions(+) > > diff --git a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi > index 85c417d9983b..0b5bcf6a7c97 100644 > --- a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi > +++ b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi > @@ -241,6 +241,23 @@ > }; > }; > > + i2c1_pins_b: i2c1-2 { > + pins { > + pinmux = <STM32_PINMUX('F', 14, AF5)>, /* I2C1_SCL */ > + <STM32_PINMUX('F', 15, AF5)>; /* I2C1_SDA */ > + bias-disable; > + drive-open-drain; > + slew-rate = <0>; > + }; > + }; > + > + i2c1_pins_sleep_b: i2c1-3 { > + pins { > + pinmux = <STM32_PINMUX('F', 14, ANALOG)>, /* I2C1_SCL */ > + <STM32_PINMUX('F', 15, ANALOG)>; /* I2C1_SDA */ > + }; > + }; > + > i2c2_pins_a: i2c2-0 { > pins { > pinmux = <STM32_PINMUX('H', 4, AF4)>, /* I2C2_SCL */ > @@ -258,6 +275,23 @@ > }; > }; > > + i2c2_pins_b: i2c2-2 { > + pins { > + pinmux = <STM32_PINMUX('Z', 0, AF3)>, /* I2C2_SCL */ > + <STM32_PINMUX('H', 5, AF4)>; /* I2C2_SDA */ You can't do that. <STM32_PINMUX('Z', 0, AF3)> has to be declared in pincontroller-z. So in your case, you have to define 2 groups for i2C2 for your default state (the same for the sleep state). regards Alex > + bias-disable; > + drive-open-drain; > + slew-rate = <0>; > + }; > + }; > + > + i2c2_pins_sleep_b: i2c2-3 { > + pins { > + pinmux = <STM32_PINMUX('Z', 0, ANALOG)>, /* I2C2_SCL */ > + <STM32_PINMUX('H', 5, ANALOG)>; /* I2C2_SDA */ > + }; > + }; > + > i2c5_pins_a: i2c5-0 { > pins { > pinmux = <STM32_PINMUX('A', 11, AF4)>, /* I2C5_SCL */ > @@ -599,6 +633,34 @@ > bias-disable; > }; > }; > + > + uart4_pins_b: uart4-1 { > + pins1 { > + pinmux = <STM32_PINMUX('D', 1, AF8)>; /* UART4_TX */ > + bias-disable; > + drive-push-pull; > + slew-rate = <0>; > + }; > + pins2 { > + pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */ > + bias-disable; > + }; > + }; > + > + uart7_pins_a: uart7-0 { > + pins1 { > + pinmux = <STM32_PINMUX('E', 8, AF7)>; /* UART4_TX */ > + bias-disable; > + drive-push-pull; > + slew-rate = <0>; > + }; > + pins2 { > + pinmux = <STM32_PINMUX('E', 7, AF7)>, /* UART4_RX */ > + <STM32_PINMUX('E', 10, AF7)>, /* UART4_CTS */ > + <STM32_PINMUX('E', 9, AF7)>; /* UART4_RTS */ > + bias-disable; > + }; > + }; > }; > > pinctrl_z: pin-controller-z@54004000 { > ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 2/3] ARM: dts: stm32mp157: Add missing pinctrl definitions 2019-05-03 7:13 ` Alexandre Torgue @ 2019-05-06 9:59 ` Manivannan Sadhasivam -1 siblings, 0 replies; 18+ messages in thread From: Manivannan Sadhasivam @ 2019-05-06 9:59 UTC (permalink / raw) To: Alexandre Torgue Cc: mcoquelin.stm32, robh+dt, linux-stm32, linux-arm-kernel, devicetree, linux-kernel, loic.pallardy Hi Alex, On Fri, May 03, 2019 at 09:13:27AM +0200, Alexandre Torgue wrote: > Hi Mani > > On 5/3/19 7:31 AM, Manivannan Sadhasivam wrote: > > Add missing pinctrl definitions for STM32MP157 MPU. > > > > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > > --- > > arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 62 +++++++++++++++++++++++ > > 1 file changed, 62 insertions(+) > > > > diff --git a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi > > index 85c417d9983b..0b5bcf6a7c97 100644 > > --- a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi > > +++ b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi > > @@ -241,6 +241,23 @@ > > }; > > }; > > + i2c1_pins_b: i2c1-2 { > > + pins { > > + pinmux = <STM32_PINMUX('F', 14, AF5)>, /* I2C1_SCL */ > > + <STM32_PINMUX('F', 15, AF5)>; /* I2C1_SDA */ > > + bias-disable; > > + drive-open-drain; > > + slew-rate = <0>; > > + }; > > + }; > > + > > + i2c1_pins_sleep_b: i2c1-3 { > > + pins { > > + pinmux = <STM32_PINMUX('F', 14, ANALOG)>, /* I2C1_SCL */ > > + <STM32_PINMUX('F', 15, ANALOG)>; /* I2C1_SDA */ > > + }; > > + }; > > + > > i2c2_pins_a: i2c2-0 { > > pins { > > pinmux = <STM32_PINMUX('H', 4, AF4)>, /* I2C2_SCL */ > > @@ -258,6 +275,23 @@ > > }; > > }; > > + i2c2_pins_b: i2c2-2 { > > + pins { > > + pinmux = <STM32_PINMUX('Z', 0, AF3)>, /* I2C2_SCL */ > > + <STM32_PINMUX('H', 5, AF4)>; /* I2C2_SDA */ > > You can't do that. <STM32_PINMUX('Z', 0, AF3)> has to be declared in > pincontroller-z. So in your case, you have to define 2 groups for i2C2 for > your default state (the same for the sleep state). > Ah, yes I failed to note pincontroller z. Will fix it in next revision! Thanks, Mani > regards > Alex > > > > > > + bias-disable; > > + drive-open-drain; > > + slew-rate = <0>; > > + }; > > + }; > > + > > + i2c2_pins_sleep_b: i2c2-3 { > > + pins { > > + pinmux = <STM32_PINMUX('Z', 0, ANALOG)>, /* I2C2_SCL */ > > + <STM32_PINMUX('H', 5, ANALOG)>; /* I2C2_SDA */ > > + }; > > + }; > > + > > i2c5_pins_a: i2c5-0 { > > pins { > > pinmux = <STM32_PINMUX('A', 11, AF4)>, /* I2C5_SCL */ > > @@ -599,6 +633,34 @@ > > bias-disable; > > }; > > }; > > + > > + uart4_pins_b: uart4-1 { > > + pins1 { > > + pinmux = <STM32_PINMUX('D', 1, AF8)>; /* UART4_TX */ > > + bias-disable; > > + drive-push-pull; > > + slew-rate = <0>; > > + }; > > + pins2 { > > + pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */ > > + bias-disable; > > + }; > > + }; > > + > > + uart7_pins_a: uart7-0 { > > + pins1 { > > + pinmux = <STM32_PINMUX('E', 8, AF7)>; /* UART4_TX */ > > + bias-disable; > > + drive-push-pull; > > + slew-rate = <0>; > > + }; > > + pins2 { > > + pinmux = <STM32_PINMUX('E', 7, AF7)>, /* UART4_RX */ > > + <STM32_PINMUX('E', 10, AF7)>, /* UART4_CTS */ > > + <STM32_PINMUX('E', 9, AF7)>; /* UART4_RTS */ > > + bias-disable; > > + }; > > + }; > > }; > > pinctrl_z: pin-controller-z@54004000 { > > ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 2/3] ARM: dts: stm32mp157: Add missing pinctrl definitions @ 2019-05-06 9:59 ` Manivannan Sadhasivam 0 siblings, 0 replies; 18+ messages in thread From: Manivannan Sadhasivam @ 2019-05-06 9:59 UTC (permalink / raw) To: Alexandre Torgue Cc: devicetree, loic.pallardy, linux-kernel, robh+dt, mcoquelin.stm32, linux-stm32, linux-arm-kernel Hi Alex, On Fri, May 03, 2019 at 09:13:27AM +0200, Alexandre Torgue wrote: > Hi Mani > > On 5/3/19 7:31 AM, Manivannan Sadhasivam wrote: > > Add missing pinctrl definitions for STM32MP157 MPU. > > > > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > > --- > > arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 62 +++++++++++++++++++++++ > > 1 file changed, 62 insertions(+) > > > > diff --git a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi > > index 85c417d9983b..0b5bcf6a7c97 100644 > > --- a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi > > +++ b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi > > @@ -241,6 +241,23 @@ > > }; > > }; > > + i2c1_pins_b: i2c1-2 { > > + pins { > > + pinmux = <STM32_PINMUX('F', 14, AF5)>, /* I2C1_SCL */ > > + <STM32_PINMUX('F', 15, AF5)>; /* I2C1_SDA */ > > + bias-disable; > > + drive-open-drain; > > + slew-rate = <0>; > > + }; > > + }; > > + > > + i2c1_pins_sleep_b: i2c1-3 { > > + pins { > > + pinmux = <STM32_PINMUX('F', 14, ANALOG)>, /* I2C1_SCL */ > > + <STM32_PINMUX('F', 15, ANALOG)>; /* I2C1_SDA */ > > + }; > > + }; > > + > > i2c2_pins_a: i2c2-0 { > > pins { > > pinmux = <STM32_PINMUX('H', 4, AF4)>, /* I2C2_SCL */ > > @@ -258,6 +275,23 @@ > > }; > > }; > > + i2c2_pins_b: i2c2-2 { > > + pins { > > + pinmux = <STM32_PINMUX('Z', 0, AF3)>, /* I2C2_SCL */ > > + <STM32_PINMUX('H', 5, AF4)>; /* I2C2_SDA */ > > You can't do that. <STM32_PINMUX('Z', 0, AF3)> has to be declared in > pincontroller-z. So in your case, you have to define 2 groups for i2C2 for > your default state (the same for the sleep state). > Ah, yes I failed to note pincontroller z. Will fix it in next revision! Thanks, Mani > regards > Alex > > > > > > + bias-disable; > > + drive-open-drain; > > + slew-rate = <0>; > > + }; > > + }; > > + > > + i2c2_pins_sleep_b: i2c2-3 { > > + pins { > > + pinmux = <STM32_PINMUX('Z', 0, ANALOG)>, /* I2C2_SCL */ > > + <STM32_PINMUX('H', 5, ANALOG)>; /* I2C2_SDA */ > > + }; > > + }; > > + > > i2c5_pins_a: i2c5-0 { > > pins { > > pinmux = <STM32_PINMUX('A', 11, AF4)>, /* I2C5_SCL */ > > @@ -599,6 +633,34 @@ > > bias-disable; > > }; > > }; > > + > > + uart4_pins_b: uart4-1 { > > + pins1 { > > + pinmux = <STM32_PINMUX('D', 1, AF8)>; /* UART4_TX */ > > + bias-disable; > > + drive-push-pull; > > + slew-rate = <0>; > > + }; > > + pins2 { > > + pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */ > > + bias-disable; > > + }; > > + }; > > + > > + uart7_pins_a: uart7-0 { > > + pins1 { > > + pinmux = <STM32_PINMUX('E', 8, AF7)>; /* UART4_TX */ > > + bias-disable; > > + drive-push-pull; > > + slew-rate = <0>; > > + }; > > + pins2 { > > + pinmux = <STM32_PINMUX('E', 7, AF7)>, /* UART4_RX */ > > + <STM32_PINMUX('E', 10, AF7)>, /* UART4_CTS */ > > + <STM32_PINMUX('E', 9, AF7)>; /* UART4_RTS */ > > + bias-disable; > > + }; > > + }; > > }; > > pinctrl_z: pin-controller-z@54004000 { > > _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH 3/3] ARM: dts: Add Avenger96 devicetree support based on STM32MP157A 2019-05-03 5:31 ` Manivannan Sadhasivam @ 2019-05-03 5:31 ` Manivannan Sadhasivam -1 siblings, 0 replies; 18+ messages in thread From: Manivannan Sadhasivam @ 2019-05-03 5:31 UTC (permalink / raw) To: mcoquelin.stm32, alexandre.torgue, robh+dt Cc: linux-stm32, linux-arm-kernel, devicetree, linux-kernel, loic.pallardy, Manivannan Sadhasivam Add devicetree support for Avenger96 board based on STM32MP157A MPU from ST Micro. This board is one of the 96Boards Consumer Edition board from Arrow Electronics and has the following features: SoC: STM32MP157AAC PMIC: STPMIC1A RAM: 1024 Mbyte @ 533MHz Storage: eMMC v4.51: 8 Gbyte microSD Socket: UHS-1 v3.01 Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac Bluetooth®v4.2 (BR/EDR/BLE) USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4 LED: 4x User LED, 1x WiFi LED, 1x BT LED More information about this board can be found in 96Boards website: https://www.96boards.org/product/avenger96/ Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/stm32mp157a-avenger96.dts | 320 ++++++++++++++++++++ 2 files changed, 321 insertions(+) create mode 100644 arch/arm/boot/dts/stm32mp157a-avenger96.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 8a1d0b3f55dd..f1d2f0bfa7c2 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -965,6 +965,7 @@ dtb-$(CONFIG_ARCH_STM32) += \ stm32h743i-eval.dtb \ stm32h743i-disco.dtb \ stm32mp157a-dk1.dtb \ + stm32mp157a-avenger96.dtb \ stm32mp157c-dk2.dtb \ stm32mp157c-ed1.dtb \ stm32mp157c-ev1.dtb diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts new file mode 100644 index 000000000000..a3b8af82ac70 --- /dev/null +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts @@ -0,0 +1,320 @@ +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) +/* + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved + * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + */ + +/dts-v1/; + +#include "stm32mp157c.dtsi" +#include "stm32mp157-pinctrl.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/mfd/st,stpmic1.h> + +/ { + model = "Arrow Electronics STM32MP157A Avenger96 board"; + compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157"; + + aliases { + ethernet0 = ðernet0; + mmc0 = &sdmmc1; + serial0 = &uart4; + serial1 = &uart7; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@c0000000 { + reg = <0xc0000000 0x40000000>; + }; + + led { + compatible = "gpio-leds"; + led1 { + label = "green:user1"; + gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led2 { + label = "green:user2"; + gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + + led3 { + label = "green:user3"; + gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc1"; + default-state = "off"; + }; + + led4 { + label = "green:user3"; + gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "none"; + default-state = "off"; + panic-indicator; + }; + + led5 { + label = "yellow:wifi"; + gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tx"; + default-state = "off"; + }; + + led6 { + label = "blue:bt"; + gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "bluetooth-power"; + default-state = "off"; + }; + }; +}; + +ðernet0 { + status = "okay"; + pinctrl-0 = <ðernet0_rgmii_pins_a>; + pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>; + pinctrl-names = "default", "sleep"; + phy-mode = "rgmii"; + max-speed = <1000>; + phy-handle = <&phy0>; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + phy0: ethernet-phy@7 { + reg = <7>; + }; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_b>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_b>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; +}; + +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; + + pmic: stpmic@33 { + compatible = "st,stpmic1"; + reg = <0x33>; + interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + status = "okay"; + + st,main-control-register = <0x04>; + st,vin-control-register = <0xc0>; + st,usb-control-register = <0x30>; + + regulators { + compatible = "st,stpmic1-regulators"; + + ldo1-supply = <&v3v3>; + ldo2-supply = <&v3v3>; + ldo3-supply = <&vdd_ddr>; + ldo5-supply = <&v3v3>; + ldo6-supply = <&v3v3>; + pwr_sw1-supply = <&bst_out>; + pwr_sw2-supply = <&bst_out>; + + vddcore: buck1 { + regulator-name = "vddcore"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd_ddr: buck2 { + regulator-name = "vdd_ddr"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd: buck3 { + regulator-name = "vdd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + st,mask_reset; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + v3v3: buck4 { + regulator-name = "v3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-over-current-protection; + regulator-initial-mode = <0>; + }; + + vdda: ldo1 { + regulator-name = "vdda"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + interrupts = <IT_CURLIM_LDO1 0>; + interrupt-parent = <&pmic>; + }; + + v2v8: ldo2 { + regulator-name = "v2v8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + interrupts = <IT_CURLIM_LDO2 0>; + interrupt-parent = <&pmic>; + }; + + vtt_ddr: ldo3 { + regulator-name = "vtt_ddr"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <750000>; + regulator-always-on; + regulator-over-current-protection; + }; + + vdd_usb: ldo4 { + regulator-name = "vdd_usb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + interrupts = <IT_CURLIM_LDO4 0>; + interrupt-parent = <&pmic>; + }; + + vdd_sd: ldo5 { + regulator-name = "vdd_sd"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + interrupts = <IT_CURLIM_LDO5 0>; + interrupt-parent = <&pmic>; + regulator-boot-on; + }; + + v1v8: ldo6 { + regulator-name = "v1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + interrupts = <IT_CURLIM_LDO6 0>; + interrupt-parent = <&pmic>; + regulator-enable-ramp-delay = <300000>; + }; + + vref_ddr: vref_ddr { + regulator-name = "vref_ddr"; + regulator-always-on; + regulator-over-current-protection; + }; + + bst_out: boost { + regulator-name = "bst_out"; + interrupts = <IT_OCP_BOOST 0>; + interrupt-parent = <&pmic>; + }; + + vbus_otg: pwr_sw1 { + regulator-name = "vbus_otg"; + interrupts = <IT_OCP_OTG 0>; + interrupt-parent = <&pmic>; + regulator-active-discharge; + }; + + vbus_sw: pwr_sw2 { + regulator-name = "vbus_sw"; + interrupts = <IT_OCP_SWOUT 0>; + interrupt-parent = <&pmic>; + regulator-active-discharge; + }; + }; + + onkey { + compatible = "st,stpmic1-onkey"; + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>; + interrupt-names = "onkey-falling", "onkey-rising"; + status = "okay"; + }; + + watchdog { + compatible = "st,stpmic1-wdt"; + status = "disabled"; + }; + }; +}; + +&iwdg2 { + timeout-sec = <32>; + status = "okay"; +}; + +&rng1 { + status = "okay"; +}; + +&rtc { + status = "okay"; +}; + +&sdmmc1 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; + broken-cd; + st,sig-dir; + st,neg-edge; + st,use-ckin; + bus-width = <4>; + vmmc-supply = <&vdd_sd>; + status = "okay"; +}; + +&uart4 { + /* On Low speed expansion header */ + label = "LS-UART1"; + pinctrl-names = "default"; + pinctrl-0 = <&uart4_pins_b>; + status = "okay"; +}; + +&uart7 { + /* On Low speed expansion header */ + label = "LS-UART0"; + pinctrl-names = "default"; + pinctrl-0 = <&uart7_pins_a>; + status = "okay"; +}; -- 2.17.1 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH 3/3] ARM: dts: Add Avenger96 devicetree support based on STM32MP157A @ 2019-05-03 5:31 ` Manivannan Sadhasivam 0 siblings, 0 replies; 18+ messages in thread From: Manivannan Sadhasivam @ 2019-05-03 5:31 UTC (permalink / raw) To: mcoquelin.stm32, alexandre.torgue, robh+dt Cc: devicetree, loic.pallardy, linux-kernel, Manivannan Sadhasivam, linux-stm32, linux-arm-kernel Add devicetree support for Avenger96 board based on STM32MP157A MPU from ST Micro. This board is one of the 96Boards Consumer Edition board from Arrow Electronics and has the following features: SoC: STM32MP157AAC PMIC: STPMIC1A RAM: 1024 Mbyte @ 533MHz Storage: eMMC v4.51: 8 Gbyte microSD Socket: UHS-1 v3.01 Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac Bluetooth®v4.2 (BR/EDR/BLE) USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4 LED: 4x User LED, 1x WiFi LED, 1x BT LED More information about this board can be found in 96Boards website: https://www.96boards.org/product/avenger96/ Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/stm32mp157a-avenger96.dts | 320 ++++++++++++++++++++ 2 files changed, 321 insertions(+) create mode 100644 arch/arm/boot/dts/stm32mp157a-avenger96.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 8a1d0b3f55dd..f1d2f0bfa7c2 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -965,6 +965,7 @@ dtb-$(CONFIG_ARCH_STM32) += \ stm32h743i-eval.dtb \ stm32h743i-disco.dtb \ stm32mp157a-dk1.dtb \ + stm32mp157a-avenger96.dtb \ stm32mp157c-dk2.dtb \ stm32mp157c-ed1.dtb \ stm32mp157c-ev1.dtb diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts new file mode 100644 index 000000000000..a3b8af82ac70 --- /dev/null +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts @@ -0,0 +1,320 @@ +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) +/* + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved + * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + */ + +/dts-v1/; + +#include "stm32mp157c.dtsi" +#include "stm32mp157-pinctrl.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/mfd/st,stpmic1.h> + +/ { + model = "Arrow Electronics STM32MP157A Avenger96 board"; + compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157"; + + aliases { + ethernet0 = ðernet0; + mmc0 = &sdmmc1; + serial0 = &uart4; + serial1 = &uart7; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@c0000000 { + reg = <0xc0000000 0x40000000>; + }; + + led { + compatible = "gpio-leds"; + led1 { + label = "green:user1"; + gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led2 { + label = "green:user2"; + gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + + led3 { + label = "green:user3"; + gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc1"; + default-state = "off"; + }; + + led4 { + label = "green:user3"; + gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "none"; + default-state = "off"; + panic-indicator; + }; + + led5 { + label = "yellow:wifi"; + gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tx"; + default-state = "off"; + }; + + led6 { + label = "blue:bt"; + gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "bluetooth-power"; + default-state = "off"; + }; + }; +}; + +ðernet0 { + status = "okay"; + pinctrl-0 = <ðernet0_rgmii_pins_a>; + pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>; + pinctrl-names = "default", "sleep"; + phy-mode = "rgmii"; + max-speed = <1000>; + phy-handle = <&phy0>; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + phy0: ethernet-phy@7 { + reg = <7>; + }; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_b>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_b>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; +}; + +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; + + pmic: stpmic@33 { + compatible = "st,stpmic1"; + reg = <0x33>; + interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + status = "okay"; + + st,main-control-register = <0x04>; + st,vin-control-register = <0xc0>; + st,usb-control-register = <0x30>; + + regulators { + compatible = "st,stpmic1-regulators"; + + ldo1-supply = <&v3v3>; + ldo2-supply = <&v3v3>; + ldo3-supply = <&vdd_ddr>; + ldo5-supply = <&v3v3>; + ldo6-supply = <&v3v3>; + pwr_sw1-supply = <&bst_out>; + pwr_sw2-supply = <&bst_out>; + + vddcore: buck1 { + regulator-name = "vddcore"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd_ddr: buck2 { + regulator-name = "vdd_ddr"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd: buck3 { + regulator-name = "vdd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + st,mask_reset; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + v3v3: buck4 { + regulator-name = "v3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-over-current-protection; + regulator-initial-mode = <0>; + }; + + vdda: ldo1 { + regulator-name = "vdda"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + interrupts = <IT_CURLIM_LDO1 0>; + interrupt-parent = <&pmic>; + }; + + v2v8: ldo2 { + regulator-name = "v2v8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + interrupts = <IT_CURLIM_LDO2 0>; + interrupt-parent = <&pmic>; + }; + + vtt_ddr: ldo3 { + regulator-name = "vtt_ddr"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <750000>; + regulator-always-on; + regulator-over-current-protection; + }; + + vdd_usb: ldo4 { + regulator-name = "vdd_usb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + interrupts = <IT_CURLIM_LDO4 0>; + interrupt-parent = <&pmic>; + }; + + vdd_sd: ldo5 { + regulator-name = "vdd_sd"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + interrupts = <IT_CURLIM_LDO5 0>; + interrupt-parent = <&pmic>; + regulator-boot-on; + }; + + v1v8: ldo6 { + regulator-name = "v1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + interrupts = <IT_CURLIM_LDO6 0>; + interrupt-parent = <&pmic>; + regulator-enable-ramp-delay = <300000>; + }; + + vref_ddr: vref_ddr { + regulator-name = "vref_ddr"; + regulator-always-on; + regulator-over-current-protection; + }; + + bst_out: boost { + regulator-name = "bst_out"; + interrupts = <IT_OCP_BOOST 0>; + interrupt-parent = <&pmic>; + }; + + vbus_otg: pwr_sw1 { + regulator-name = "vbus_otg"; + interrupts = <IT_OCP_OTG 0>; + interrupt-parent = <&pmic>; + regulator-active-discharge; + }; + + vbus_sw: pwr_sw2 { + regulator-name = "vbus_sw"; + interrupts = <IT_OCP_SWOUT 0>; + interrupt-parent = <&pmic>; + regulator-active-discharge; + }; + }; + + onkey { + compatible = "st,stpmic1-onkey"; + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>; + interrupt-names = "onkey-falling", "onkey-rising"; + status = "okay"; + }; + + watchdog { + compatible = "st,stpmic1-wdt"; + status = "disabled"; + }; + }; +}; + +&iwdg2 { + timeout-sec = <32>; + status = "okay"; +}; + +&rng1 { + status = "okay"; +}; + +&rtc { + status = "okay"; +}; + +&sdmmc1 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; + broken-cd; + st,sig-dir; + st,neg-edge; + st,use-ckin; + bus-width = <4>; + vmmc-supply = <&vdd_sd>; + status = "okay"; +}; + +&uart4 { + /* On Low speed expansion header */ + label = "LS-UART1"; + pinctrl-names = "default"; + pinctrl-0 = <&uart4_pins_b>; + status = "okay"; +}; + +&uart7 { + /* On Low speed expansion header */ + label = "LS-UART0"; + pinctrl-names = "default"; + pinctrl-0 = <&uart7_pins_a>; + status = "okay"; +}; -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 18+ messages in thread
* Re: [PATCH 3/3] ARM: dts: Add Avenger96 devicetree support based on STM32MP157A 2019-05-03 5:31 ` Manivannan Sadhasivam (?) @ 2019-05-03 9:01 ` Alexandre Torgue -1 siblings, 0 replies; 18+ messages in thread From: Alexandre Torgue @ 2019-05-03 9:01 UTC (permalink / raw) To: Manivannan Sadhasivam, mcoquelin.stm32, robh+dt Cc: linux-stm32, linux-arm-kernel, devicetree, linux-kernel, loic.pallardy Hi Mani On 5/3/19 7:31 AM, Manivannan Sadhasivam wrote: > Add devicetree support for Avenger96 board based on STM32MP157A MPU > from ST Micro. This board is one of the 96Boards Consumer Edition board > from Arrow Electronics and has the following features: > > SoC: STM32MP157AAC > PMIC: STPMIC1A > RAM: 1024 Mbyte @ 533MHz > Storage: eMMC v4.51: 8 Gbyte > microSD Socket: UHS-1 v3.01 > Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant > Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac > Bluetooth®v4.2 (BR/EDR/BLE) > USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG > Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4 > LED: 4x User LED, 1x WiFi LED, 1x BT LED > > More information about this board can be found in 96Boards website: > https://www.96boards.org/product/avenger96/ > > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/stm32mp157a-avenger96.dts | 320 ++++++++++++++++++++ > 2 files changed, 321 insertions(+) > create mode 100644 arch/arm/boot/dts/stm32mp157a-avenger96.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 8a1d0b3f55dd..f1d2f0bfa7c2 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -965,6 +965,7 @@ dtb-$(CONFIG_ARCH_STM32) += \ > stm32h743i-eval.dtb \ > stm32h743i-disco.dtb \ > stm32mp157a-dk1.dtb \ > + stm32mp157a-avenger96.dtb \ follow alphabetic order please. > stm32mp157c-dk2.dtb \ > stm32mp157c-ed1.dtb \ > stm32mp157c-ev1.dtb > diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts > new file mode 100644 > index 000000000000..a3b8af82ac70 > --- /dev/null > +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts > @@ -0,0 +1,320 @@ > +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) > +/* > + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved > + * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > + */ > + > +/dts-v1/; > + > +#include "stm32mp157c.dtsi" > +#include "stm32mp157-pinctrl.dtsi" > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/mfd/st,stpmic1.h> > + > +/ { > + model = "Arrow Electronics STM32MP157A Avenger96 board"; > + compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157"; > + > + aliases { > + ethernet0 = ðernet0; > + mmc0 = &sdmmc1; > + serial0 = &uart4; > + serial1 = &uart7; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + memory@c0000000 { > + reg = <0xc0000000 0x40000000>; you could add device_type = "memory"; > + }; > + > + led { > + compatible = "gpio-leds"; > + led1 { > + label = "green:user1"; > + gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "heartbeat"; > + default-state = "off"; > + }; > + > + led2 { > + label = "green:user2"; > + gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "mmc0"; > + default-state = "off"; > + }; > + > + led3 { > + label = "green:user3"; > + gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "mmc1"; > + default-state = "off"; > + }; > + > + led4 { > + label = "green:user3"; > + gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "none"; > + default-state = "off"; > + panic-indicator; > + }; > + > + led5 { > + label = "yellow:wifi"; > + gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "phy0tx"; > + default-state = "off"; > + }; > + > + led6 { > + label = "blue:bt"; > + gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "bluetooth-power"; > + default-state = "off"; > + }; > + }; > +}; > + > +ðernet0 { > + status = "okay"; > + pinctrl-0 = <ðernet0_rgmii_pins_a>; > + pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>; > + pinctrl-names = "default", "sleep"; > + phy-mode = "rgmii"; > + max-speed = <1000>; > + phy-handle = <&phy0>; > + > + mdio0 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "snps,dwmac-mdio"; > + phy0: ethernet-phy@7 { > + reg = <7>; > + }; > + }; > +}; > + > +&i2c1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c1_pins_b>; > + i2c-scl-rising-time-ns = <185>; > + i2c-scl-falling-time-ns = <20>; > + status = "okay"; > + /delete-property/dmas; > + /delete-property/dma-names; > +}; > + > +&i2c2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c2_pins_b>; > + i2c-scl-rising-time-ns = <185>; > + i2c-scl-falling-time-ns = <20>; > + status = "okay"; > + /delete-property/dmas; > + /delete-property/dma-names; > +}; > + > +&i2c4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c4_pins_a>; > + i2c-scl-rising-time-ns = <185>; > + i2c-scl-falling-time-ns = <20>; > + status = "okay"; > + /delete-property/dmas; > + /delete-property/dma-names; > + > + pmic: stpmic@33 { > + compatible = "st,stpmic1"; > + reg = <0x33>; > + interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>; > + interrupt-controller; > + #interrupt-cells = <2>; > + status = "okay"; > + > + st,main-control-register = <0x04>; > + st,vin-control-register = <0xc0>; > + st,usb-control-register = <0x30>; > + > + regulators { > + compatible = "st,stpmic1-regulators"; > + > + ldo1-supply = <&v3v3>; > + ldo2-supply = <&v3v3>; > + ldo3-supply = <&vdd_ddr>; > + ldo5-supply = <&v3v3>; > + ldo6-supply = <&v3v3>; > + pwr_sw1-supply = <&bst_out>; > + pwr_sw2-supply = <&bst_out>; > + > + vddcore: buck1 { > + regulator-name = "vddcore"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1350000>; > + regulator-always-on; > + regulator-initial-mode = <0>; > + regulator-over-current-protection; > + }; > + > + vdd_ddr: buck2 { > + regulator-name = "vdd_ddr"; > + regulator-min-microvolt = <1350000>; > + regulator-max-microvolt = <1350000>; > + regulator-always-on; > + regulator-initial-mode = <0>; > + regulator-over-current-protection; > + }; > + > + vdd: buck3 { > + regulator-name = "vdd"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + st,mask_reset; > + regulator-initial-mode = <0>; > + regulator-over-current-protection; > + }; > + > + v3v3: buck4 { > + regulator-name = "v3v3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + regulator-over-current-protection; > + regulator-initial-mode = <0>; > + }; > + > + vdda: ldo1 { > + regulator-name = "vdda"; > + regulator-min-microvolt = <2900000>; > + regulator-max-microvolt = <2900000>; > + interrupts = <IT_CURLIM_LDO1 0>; > + interrupt-parent = <&pmic>; > + }; > + > + v2v8: ldo2 { > + regulator-name = "v2v8"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + interrupts = <IT_CURLIM_LDO2 0>; > + interrupt-parent = <&pmic>; > + }; > + > + vtt_ddr: ldo3 { > + regulator-name = "vtt_ddr"; > + regulator-min-microvolt = <500000>; > + regulator-max-microvolt = <750000>; > + regulator-always-on; > + regulator-over-current-protection; > + }; > + > + vdd_usb: ldo4 { > + regulator-name = "vdd_usb"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + interrupts = <IT_CURLIM_LDO4 0>; > + interrupt-parent = <&pmic>; > + }; > + > + vdd_sd: ldo5 { > + regulator-name = "vdd_sd"; > + regulator-min-microvolt = <2900000>; > + regulator-max-microvolt = <2900000>; > + interrupts = <IT_CURLIM_LDO5 0>; > + interrupt-parent = <&pmic>; > + regulator-boot-on; > + }; > + > + v1v8: ldo6 { > + regulator-name = "v1v8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + interrupts = <IT_CURLIM_LDO6 0>; > + interrupt-parent = <&pmic>; > + regulator-enable-ramp-delay = <300000>; > + }; > + > + vref_ddr: vref_ddr { > + regulator-name = "vref_ddr"; > + regulator-always-on; > + regulator-over-current-protection; > + }; > + > + bst_out: boost { > + regulator-name = "bst_out"; > + interrupts = <IT_OCP_BOOST 0>; > + interrupt-parent = <&pmic>; > + }; > + > + vbus_otg: pwr_sw1 { > + regulator-name = "vbus_otg"; > + interrupts = <IT_OCP_OTG 0>; > + interrupt-parent = <&pmic>; > + regulator-active-discharge; > + }; > + > + vbus_sw: pwr_sw2 { > + regulator-name = "vbus_sw"; > + interrupts = <IT_OCP_SWOUT 0>; > + interrupt-parent = <&pmic>; > + regulator-active-discharge; > + }; > + }; > + > + onkey { > + compatible = "st,stpmic1-onkey"; > + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>; > + interrupt-names = "onkey-falling", "onkey-rising"; > + status = "okay"; > + }; > + > + watchdog { > + compatible = "st,stpmic1-wdt"; > + status = "disabled"; > + }; > + }; > +}; > + > +&iwdg2 { > + timeout-sec = <32>; > + status = "okay"; > +}; > + > +&rng1 { > + status = "okay"; > +}; > + > +&rtc { > + status = "okay"; > +}; > + > +&sdmmc1 { > + pinctrl-names = "default", "opendrain", "sleep"; > + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>; > + pinctrl-1 = <&sdmmc1_b4_od_pins_a>; > + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; > + broken-cd; > + st,sig-dir; > + st,neg-edge; > + st,use-ckin; > + bus-width = <4>; > + vmmc-supply = <&vdd_sd>; > + status = "okay"; > +}; > + > +&uart4 { > + /* On Low speed expansion header */ > + label = "LS-UART1"; > + pinctrl-names = "default"; > + pinctrl-0 = <&uart4_pins_b>; > + status = "okay"; > +}; > + > +&uart7 { > + /* On Low speed expansion header */ > + label = "LS-UART0"; > + pinctrl-names = "default"; > + pinctrl-0 = <&uart7_pins_a>; > + status = "okay"; > +}; > ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 3/3] ARM: dts: Add Avenger96 devicetree support based on STM32MP157A @ 2019-05-03 9:01 ` Alexandre Torgue 0 siblings, 0 replies; 18+ messages in thread From: Alexandre Torgue @ 2019-05-03 9:01 UTC (permalink / raw) To: Manivannan Sadhasivam, mcoquelin.stm32, robh+dt Cc: devicetree, loic.pallardy, linux-stm32, linux-arm-kernel, linux-kernel Hi Mani On 5/3/19 7:31 AM, Manivannan Sadhasivam wrote: > Add devicetree support for Avenger96 board based on STM32MP157A MPU > from ST Micro. This board is one of the 96Boards Consumer Edition board > from Arrow Electronics and has the following features: > > SoC: STM32MP157AAC > PMIC: STPMIC1A > RAM: 1024 Mbyte @ 533MHz > Storage: eMMC v4.51: 8 Gbyte > microSD Socket: UHS-1 v3.01 > Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant > Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac > Bluetooth®v4.2 (BR/EDR/BLE) > USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG > Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4 > LED: 4x User LED, 1x WiFi LED, 1x BT LED > > More information about this board can be found in 96Boards website: > https://www.96boards.org/product/avenger96/ > > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/stm32mp157a-avenger96.dts | 320 ++++++++++++++++++++ > 2 files changed, 321 insertions(+) > create mode 100644 arch/arm/boot/dts/stm32mp157a-avenger96.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 8a1d0b3f55dd..f1d2f0bfa7c2 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -965,6 +965,7 @@ dtb-$(CONFIG_ARCH_STM32) += \ > stm32h743i-eval.dtb \ > stm32h743i-disco.dtb \ > stm32mp157a-dk1.dtb \ > + stm32mp157a-avenger96.dtb \ follow alphabetic order please. > stm32mp157c-dk2.dtb \ > stm32mp157c-ed1.dtb \ > stm32mp157c-ev1.dtb > diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts > new file mode 100644 > index 000000000000..a3b8af82ac70 > --- /dev/null > +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts > @@ -0,0 +1,320 @@ > +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) > +/* > + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved > + * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > + */ > + > +/dts-v1/; > + > +#include "stm32mp157c.dtsi" > +#include "stm32mp157-pinctrl.dtsi" > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/mfd/st,stpmic1.h> > + > +/ { > + model = "Arrow Electronics STM32MP157A Avenger96 board"; > + compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157"; > + > + aliases { > + ethernet0 = ðernet0; > + mmc0 = &sdmmc1; > + serial0 = &uart4; > + serial1 = &uart7; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + memory@c0000000 { > + reg = <0xc0000000 0x40000000>; you could add device_type = "memory"; > + }; > + > + led { > + compatible = "gpio-leds"; > + led1 { > + label = "green:user1"; > + gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "heartbeat"; > + default-state = "off"; > + }; > + > + led2 { > + label = "green:user2"; > + gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "mmc0"; > + default-state = "off"; > + }; > + > + led3 { > + label = "green:user3"; > + gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "mmc1"; > + default-state = "off"; > + }; > + > + led4 { > + label = "green:user3"; > + gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "none"; > + default-state = "off"; > + panic-indicator; > + }; > + > + led5 { > + label = "yellow:wifi"; > + gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "phy0tx"; > + default-state = "off"; > + }; > + > + led6 { > + label = "blue:bt"; > + gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "bluetooth-power"; > + default-state = "off"; > + }; > + }; > +}; > + > +ðernet0 { > + status = "okay"; > + pinctrl-0 = <ðernet0_rgmii_pins_a>; > + pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>; > + pinctrl-names = "default", "sleep"; > + phy-mode = "rgmii"; > + max-speed = <1000>; > + phy-handle = <&phy0>; > + > + mdio0 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "snps,dwmac-mdio"; > + phy0: ethernet-phy@7 { > + reg = <7>; > + }; > + }; > +}; > + > +&i2c1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c1_pins_b>; > + i2c-scl-rising-time-ns = <185>; > + i2c-scl-falling-time-ns = <20>; > + status = "okay"; > + /delete-property/dmas; > + /delete-property/dma-names; > +}; > + > +&i2c2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c2_pins_b>; > + i2c-scl-rising-time-ns = <185>; > + i2c-scl-falling-time-ns = <20>; > + status = "okay"; > + /delete-property/dmas; > + /delete-property/dma-names; > +}; > + > +&i2c4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c4_pins_a>; > + i2c-scl-rising-time-ns = <185>; > + i2c-scl-falling-time-ns = <20>; > + status = "okay"; > + /delete-property/dmas; > + /delete-property/dma-names; > + > + pmic: stpmic@33 { > + compatible = "st,stpmic1"; > + reg = <0x33>; > + interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>; > + interrupt-controller; > + #interrupt-cells = <2>; > + status = "okay"; > + > + st,main-control-register = <0x04>; > + st,vin-control-register = <0xc0>; > + st,usb-control-register = <0x30>; > + > + regulators { > + compatible = "st,stpmic1-regulators"; > + > + ldo1-supply = <&v3v3>; > + ldo2-supply = <&v3v3>; > + ldo3-supply = <&vdd_ddr>; > + ldo5-supply = <&v3v3>; > + ldo6-supply = <&v3v3>; > + pwr_sw1-supply = <&bst_out>; > + pwr_sw2-supply = <&bst_out>; > + > + vddcore: buck1 { > + regulator-name = "vddcore"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1350000>; > + regulator-always-on; > + regulator-initial-mode = <0>; > + regulator-over-current-protection; > + }; > + > + vdd_ddr: buck2 { > + regulator-name = "vdd_ddr"; > + regulator-min-microvolt = <1350000>; > + regulator-max-microvolt = <1350000>; > + regulator-always-on; > + regulator-initial-mode = <0>; > + regulator-over-current-protection; > + }; > + > + vdd: buck3 { > + regulator-name = "vdd"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + st,mask_reset; > + regulator-initial-mode = <0>; > + regulator-over-current-protection; > + }; > + > + v3v3: buck4 { > + regulator-name = "v3v3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + regulator-over-current-protection; > + regulator-initial-mode = <0>; > + }; > + > + vdda: ldo1 { > + regulator-name = "vdda"; > + regulator-min-microvolt = <2900000>; > + regulator-max-microvolt = <2900000>; > + interrupts = <IT_CURLIM_LDO1 0>; > + interrupt-parent = <&pmic>; > + }; > + > + v2v8: ldo2 { > + regulator-name = "v2v8"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + interrupts = <IT_CURLIM_LDO2 0>; > + interrupt-parent = <&pmic>; > + }; > + > + vtt_ddr: ldo3 { > + regulator-name = "vtt_ddr"; > + regulator-min-microvolt = <500000>; > + regulator-max-microvolt = <750000>; > + regulator-always-on; > + regulator-over-current-protection; > + }; > + > + vdd_usb: ldo4 { > + regulator-name = "vdd_usb"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + interrupts = <IT_CURLIM_LDO4 0>; > + interrupt-parent = <&pmic>; > + }; > + > + vdd_sd: ldo5 { > + regulator-name = "vdd_sd"; > + regulator-min-microvolt = <2900000>; > + regulator-max-microvolt = <2900000>; > + interrupts = <IT_CURLIM_LDO5 0>; > + interrupt-parent = <&pmic>; > + regulator-boot-on; > + }; > + > + v1v8: ldo6 { > + regulator-name = "v1v8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + interrupts = <IT_CURLIM_LDO6 0>; > + interrupt-parent = <&pmic>; > + regulator-enable-ramp-delay = <300000>; > + }; > + > + vref_ddr: vref_ddr { > + regulator-name = "vref_ddr"; > + regulator-always-on; > + regulator-over-current-protection; > + }; > + > + bst_out: boost { > + regulator-name = "bst_out"; > + interrupts = <IT_OCP_BOOST 0>; > + interrupt-parent = <&pmic>; > + }; > + > + vbus_otg: pwr_sw1 { > + regulator-name = "vbus_otg"; > + interrupts = <IT_OCP_OTG 0>; > + interrupt-parent = <&pmic>; > + regulator-active-discharge; > + }; > + > + vbus_sw: pwr_sw2 { > + regulator-name = "vbus_sw"; > + interrupts = <IT_OCP_SWOUT 0>; > + interrupt-parent = <&pmic>; > + regulator-active-discharge; > + }; > + }; > + > + onkey { > + compatible = "st,stpmic1-onkey"; > + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>; > + interrupt-names = "onkey-falling", "onkey-rising"; > + status = "okay"; > + }; > + > + watchdog { > + compatible = "st,stpmic1-wdt"; > + status = "disabled"; > + }; > + }; > +}; > + > +&iwdg2 { > + timeout-sec = <32>; > + status = "okay"; > +}; > + > +&rng1 { > + status = "okay"; > +}; > + > +&rtc { > + status = "okay"; > +}; > + > +&sdmmc1 { > + pinctrl-names = "default", "opendrain", "sleep"; > + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>; > + pinctrl-1 = <&sdmmc1_b4_od_pins_a>; > + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; > + broken-cd; > + st,sig-dir; > + st,neg-edge; > + st,use-ckin; > + bus-width = <4>; > + vmmc-supply = <&vdd_sd>; > + status = "okay"; > +}; > + > +&uart4 { > + /* On Low speed expansion header */ > + label = "LS-UART1"; > + pinctrl-names = "default"; > + pinctrl-0 = <&uart4_pins_b>; > + status = "okay"; > +}; > + > +&uart7 { > + /* On Low speed expansion header */ > + label = "LS-UART0"; > + pinctrl-names = "default"; > + pinctrl-0 = <&uart7_pins_a>; > + status = "okay"; > +}; > _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 3/3] ARM: dts: Add Avenger96 devicetree support based on STM32MP157A @ 2019-05-03 9:01 ` Alexandre Torgue 0 siblings, 0 replies; 18+ messages in thread From: Alexandre Torgue @ 2019-05-03 9:01 UTC (permalink / raw) To: Manivannan Sadhasivam, mcoquelin.stm32, robh+dt Cc: linux-stm32, linux-arm-kernel, devicetree, linux-kernel, loic.pallardy Hi Mani On 5/3/19 7:31 AM, Manivannan Sadhasivam wrote: > Add devicetree support for Avenger96 board based on STM32MP157A MPU > from ST Micro. This board is one of the 96Boards Consumer Edition board > from Arrow Electronics and has the following features: > > SoC: STM32MP157AAC > PMIC: STPMIC1A > RAM: 1024 Mbyte @ 533MHz > Storage: eMMC v4.51: 8 Gbyte > microSD Socket: UHS-1 v3.01 > Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant > Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac > Bluetooth®v4.2 (BR/EDR/BLE) > USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG > Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4 > LED: 4x User LED, 1x WiFi LED, 1x BT LED > > More information about this board can be found in 96Boards website: > https://www.96boards.org/product/avenger96/ > > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/stm32mp157a-avenger96.dts | 320 ++++++++++++++++++++ > 2 files changed, 321 insertions(+) > create mode 100644 arch/arm/boot/dts/stm32mp157a-avenger96.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 8a1d0b3f55dd..f1d2f0bfa7c2 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -965,6 +965,7 @@ dtb-$(CONFIG_ARCH_STM32) += \ > stm32h743i-eval.dtb \ > stm32h743i-disco.dtb \ > stm32mp157a-dk1.dtb \ > + stm32mp157a-avenger96.dtb \ follow alphabetic order please. > stm32mp157c-dk2.dtb \ > stm32mp157c-ed1.dtb \ > stm32mp157c-ev1.dtb > diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts > new file mode 100644 > index 000000000000..a3b8af82ac70 > --- /dev/null > +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts > @@ -0,0 +1,320 @@ > +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) > +/* > + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved > + * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > + */ > + > +/dts-v1/; > + > +#include "stm32mp157c.dtsi" > +#include "stm32mp157-pinctrl.dtsi" > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/mfd/st,stpmic1.h> > + > +/ { > + model = "Arrow Electronics STM32MP157A Avenger96 board"; > + compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157"; > + > + aliases { > + ethernet0 = ðernet0; > + mmc0 = &sdmmc1; > + serial0 = &uart4; > + serial1 = &uart7; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + memory@c0000000 { > + reg = <0xc0000000 0x40000000>; you could add device_type = "memory"; > + }; > + > + led { > + compatible = "gpio-leds"; > + led1 { > + label = "green:user1"; > + gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "heartbeat"; > + default-state = "off"; > + }; > + > + led2 { > + label = "green:user2"; > + gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "mmc0"; > + default-state = "off"; > + }; > + > + led3 { > + label = "green:user3"; > + gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "mmc1"; > + default-state = "off"; > + }; > + > + led4 { > + label = "green:user3"; > + gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "none"; > + default-state = "off"; > + panic-indicator; > + }; > + > + led5 { > + label = "yellow:wifi"; > + gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "phy0tx"; > + default-state = "off"; > + }; > + > + led6 { > + label = "blue:bt"; > + gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "bluetooth-power"; > + default-state = "off"; > + }; > + }; > +}; > + > +ðernet0 { > + status = "okay"; > + pinctrl-0 = <ðernet0_rgmii_pins_a>; > + pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>; > + pinctrl-names = "default", "sleep"; > + phy-mode = "rgmii"; > + max-speed = <1000>; > + phy-handle = <&phy0>; > + > + mdio0 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "snps,dwmac-mdio"; > + phy0: ethernet-phy@7 { > + reg = <7>; > + }; > + }; > +}; > + > +&i2c1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c1_pins_b>; > + i2c-scl-rising-time-ns = <185>; > + i2c-scl-falling-time-ns = <20>; > + status = "okay"; > + /delete-property/dmas; > + /delete-property/dma-names; > +}; > + > +&i2c2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c2_pins_b>; > + i2c-scl-rising-time-ns = <185>; > + i2c-scl-falling-time-ns = <20>; > + status = "okay"; > + /delete-property/dmas; > + /delete-property/dma-names; > +}; > + > +&i2c4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c4_pins_a>; > + i2c-scl-rising-time-ns = <185>; > + i2c-scl-falling-time-ns = <20>; > + status = "okay"; > + /delete-property/dmas; > + /delete-property/dma-names; > + > + pmic: stpmic@33 { > + compatible = "st,stpmic1"; > + reg = <0x33>; > + interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>; > + interrupt-controller; > + #interrupt-cells = <2>; > + status = "okay"; > + > + st,main-control-register = <0x04>; > + st,vin-control-register = <0xc0>; > + st,usb-control-register = <0x30>; > + > + regulators { > + compatible = "st,stpmic1-regulators"; > + > + ldo1-supply = <&v3v3>; > + ldo2-supply = <&v3v3>; > + ldo3-supply = <&vdd_ddr>; > + ldo5-supply = <&v3v3>; > + ldo6-supply = <&v3v3>; > + pwr_sw1-supply = <&bst_out>; > + pwr_sw2-supply = <&bst_out>; > + > + vddcore: buck1 { > + regulator-name = "vddcore"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1350000>; > + regulator-always-on; > + regulator-initial-mode = <0>; > + regulator-over-current-protection; > + }; > + > + vdd_ddr: buck2 { > + regulator-name = "vdd_ddr"; > + regulator-min-microvolt = <1350000>; > + regulator-max-microvolt = <1350000>; > + regulator-always-on; > + regulator-initial-mode = <0>; > + regulator-over-current-protection; > + }; > + > + vdd: buck3 { > + regulator-name = "vdd"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + st,mask_reset; > + regulator-initial-mode = <0>; > + regulator-over-current-protection; > + }; > + > + v3v3: buck4 { > + regulator-name = "v3v3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + regulator-over-current-protection; > + regulator-initial-mode = <0>; > + }; > + > + vdda: ldo1 { > + regulator-name = "vdda"; > + regulator-min-microvolt = <2900000>; > + regulator-max-microvolt = <2900000>; > + interrupts = <IT_CURLIM_LDO1 0>; > + interrupt-parent = <&pmic>; > + }; > + > + v2v8: ldo2 { > + regulator-name = "v2v8"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + interrupts = <IT_CURLIM_LDO2 0>; > + interrupt-parent = <&pmic>; > + }; > + > + vtt_ddr: ldo3 { > + regulator-name = "vtt_ddr"; > + regulator-min-microvolt = <500000>; > + regulator-max-microvolt = <750000>; > + regulator-always-on; > + regulator-over-current-protection; > + }; > + > + vdd_usb: ldo4 { > + regulator-name = "vdd_usb"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + interrupts = <IT_CURLIM_LDO4 0>; > + interrupt-parent = <&pmic>; > + }; > + > + vdd_sd: ldo5 { > + regulator-name = "vdd_sd"; > + regulator-min-microvolt = <2900000>; > + regulator-max-microvolt = <2900000>; > + interrupts = <IT_CURLIM_LDO5 0>; > + interrupt-parent = <&pmic>; > + regulator-boot-on; > + }; > + > + v1v8: ldo6 { > + regulator-name = "v1v8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + interrupts = <IT_CURLIM_LDO6 0>; > + interrupt-parent = <&pmic>; > + regulator-enable-ramp-delay = <300000>; > + }; > + > + vref_ddr: vref_ddr { > + regulator-name = "vref_ddr"; > + regulator-always-on; > + regulator-over-current-protection; > + }; > + > + bst_out: boost { > + regulator-name = "bst_out"; > + interrupts = <IT_OCP_BOOST 0>; > + interrupt-parent = <&pmic>; > + }; > + > + vbus_otg: pwr_sw1 { > + regulator-name = "vbus_otg"; > + interrupts = <IT_OCP_OTG 0>; > + interrupt-parent = <&pmic>; > + regulator-active-discharge; > + }; > + > + vbus_sw: pwr_sw2 { > + regulator-name = "vbus_sw"; > + interrupts = <IT_OCP_SWOUT 0>; > + interrupt-parent = <&pmic>; > + regulator-active-discharge; > + }; > + }; > + > + onkey { > + compatible = "st,stpmic1-onkey"; > + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>; > + interrupt-names = "onkey-falling", "onkey-rising"; > + status = "okay"; > + }; > + > + watchdog { > + compatible = "st,stpmic1-wdt"; > + status = "disabled"; > + }; > + }; > +}; > + > +&iwdg2 { > + timeout-sec = <32>; > + status = "okay"; > +}; > + > +&rng1 { > + status = "okay"; > +}; > + > +&rtc { > + status = "okay"; > +}; > + > +&sdmmc1 { > + pinctrl-names = "default", "opendrain", "sleep"; > + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>; > + pinctrl-1 = <&sdmmc1_b4_od_pins_a>; > + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; > + broken-cd; > + st,sig-dir; > + st,neg-edge; > + st,use-ckin; > + bus-width = <4>; > + vmmc-supply = <&vdd_sd>; > + status = "okay"; > +}; > + > +&uart4 { > + /* On Low speed expansion header */ > + label = "LS-UART1"; > + pinctrl-names = "default"; > + pinctrl-0 = <&uart4_pins_b>; > + status = "okay"; > +}; > + > +&uart7 { > + /* On Low speed expansion header */ > + label = "LS-UART0"; > + pinctrl-names = "default"; > + pinctrl-0 = <&uart7_pins_a>; > + status = "okay"; > +}; > ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 3/3] ARM: dts: Add Avenger96 devicetree support based on STM32MP157A 2019-05-03 9:01 ` Alexandre Torgue @ 2019-05-06 10:00 ` Manivannan Sadhasivam -1 siblings, 0 replies; 18+ messages in thread From: Manivannan Sadhasivam @ 2019-05-06 10:00 UTC (permalink / raw) To: Alexandre Torgue Cc: mcoquelin.stm32, robh+dt, linux-stm32, linux-arm-kernel, devicetree, linux-kernel, loic.pallardy Hi Alex, On Fri, May 03, 2019 at 11:01:00AM +0200, Alexandre Torgue wrote: > Hi Mani > > On 5/3/19 7:31 AM, Manivannan Sadhasivam wrote: > > Add devicetree support for Avenger96 board based on STM32MP157A MPU > > from ST Micro. This board is one of the 96Boards Consumer Edition board > > from Arrow Electronics and has the following features: > > > > SoC: STM32MP157AAC > > PMIC: STPMIC1A > > RAM: 1024 Mbyte @ 533MHz > > Storage: eMMC v4.51: 8 Gbyte > > microSD Socket: UHS-1 v3.01 > > Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant > > Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac > > Bluetooth®v4.2 (BR/EDR/BLE) > > USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG > > Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4 > > LED: 4x User LED, 1x WiFi LED, 1x BT LED > > > > More information about this board can be found in 96Boards website: > > https://www.96boards.org/product/avenger96/ > > > > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > > --- > > arch/arm/boot/dts/Makefile | 1 + > > arch/arm/boot/dts/stm32mp157a-avenger96.dts | 320 ++++++++++++++++++++ > > 2 files changed, 321 insertions(+) > > create mode 100644 arch/arm/boot/dts/stm32mp157a-avenger96.dts > > > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > > index 8a1d0b3f55dd..f1d2f0bfa7c2 100644 > > --- a/arch/arm/boot/dts/Makefile > > +++ b/arch/arm/boot/dts/Makefile > > @@ -965,6 +965,7 @@ dtb-$(CONFIG_ARCH_STM32) += \ > > stm32h743i-eval.dtb \ > > stm32h743i-disco.dtb \ > > stm32mp157a-dk1.dtb \ > > + stm32mp157a-avenger96.dtb \ > > follow alphabetic order please. > Ack > > stm32mp157c-dk2.dtb \ > > stm32mp157c-ed1.dtb \ > > stm32mp157c-ev1.dtb > > diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts > > new file mode 100644 > > index 000000000000..a3b8af82ac70 > > --- /dev/null > > +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts > > @@ -0,0 +1,320 @@ > > +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) > > +/* > > + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved > > + * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > > + */ > > + > > +/dts-v1/; > > + > > +#include "stm32mp157c.dtsi" > > +#include "stm32mp157-pinctrl.dtsi" > > +#include <dt-bindings/gpio/gpio.h> > > +#include <dt-bindings/mfd/st,stpmic1.h> > > + > > +/ { > > + model = "Arrow Electronics STM32MP157A Avenger96 board"; > > + compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157"; > > + > > + aliases { > > + ethernet0 = ðernet0; > > + mmc0 = &sdmmc1; > > + serial0 = &uart4; > > + serial1 = &uart7; > > + }; > > + > > + chosen { > > + stdout-path = "serial0:115200n8"; > > + }; > > + > > + memory@c0000000 { > > + reg = <0xc0000000 0x40000000>; > > you could add device_type = "memory"; > Ack. Thanks, Mani > > + }; > > + > > + led { > > + compatible = "gpio-leds"; > > + led1 { > > + label = "green:user1"; > > + gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>; > > + linux,default-trigger = "heartbeat"; > > + default-state = "off"; > > + }; > > + > > + led2 { > > + label = "green:user2"; > > + gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>; > > + linux,default-trigger = "mmc0"; > > + default-state = "off"; > > + }; > > + > > + led3 { > > + label = "green:user3"; > > + gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>; > > + linux,default-trigger = "mmc1"; > > + default-state = "off"; > > + }; > > + > > + led4 { > > + label = "green:user3"; > > + gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>; > > + linux,default-trigger = "none"; > > + default-state = "off"; > > + panic-indicator; > > + }; > > + > > + led5 { > > + label = "yellow:wifi"; > > + gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>; > > + linux,default-trigger = "phy0tx"; > > + default-state = "off"; > > + }; > > + > > + led6 { > > + label = "blue:bt"; > > + gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>; > > + linux,default-trigger = "bluetooth-power"; > > + default-state = "off"; > > + }; > > + }; > > +}; > > + > > +ðernet0 { > > + status = "okay"; > > + pinctrl-0 = <ðernet0_rgmii_pins_a>; > > + pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>; > > + pinctrl-names = "default", "sleep"; > > + phy-mode = "rgmii"; > > + max-speed = <1000>; > > + phy-handle = <&phy0>; > > + > > + mdio0 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + compatible = "snps,dwmac-mdio"; > > + phy0: ethernet-phy@7 { > > + reg = <7>; > > + }; > > + }; > > +}; > > + > > +&i2c1 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&i2c1_pins_b>; > > + i2c-scl-rising-time-ns = <185>; > > + i2c-scl-falling-time-ns = <20>; > > + status = "okay"; > > + /delete-property/dmas; > > + /delete-property/dma-names; > > +}; > > + > > +&i2c2 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&i2c2_pins_b>; > > + i2c-scl-rising-time-ns = <185>; > > + i2c-scl-falling-time-ns = <20>; > > + status = "okay"; > > + /delete-property/dmas; > > + /delete-property/dma-names; > > +}; > > + > > +&i2c4 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&i2c4_pins_a>; > > + i2c-scl-rising-time-ns = <185>; > > + i2c-scl-falling-time-ns = <20>; > > + status = "okay"; > > + /delete-property/dmas; > > + /delete-property/dma-names; > > + > > + pmic: stpmic@33 { > > + compatible = "st,stpmic1"; > > + reg = <0x33>; > > + interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>; > > + interrupt-controller; > > + #interrupt-cells = <2>; > > + status = "okay"; > > + > > + st,main-control-register = <0x04>; > > + st,vin-control-register = <0xc0>; > > + st,usb-control-register = <0x30>; > > + > > + regulators { > > + compatible = "st,stpmic1-regulators"; > > + > > + ldo1-supply = <&v3v3>; > > + ldo2-supply = <&v3v3>; > > + ldo3-supply = <&vdd_ddr>; > > + ldo5-supply = <&v3v3>; > > + ldo6-supply = <&v3v3>; > > + pwr_sw1-supply = <&bst_out>; > > + pwr_sw2-supply = <&bst_out>; > > + > > + vddcore: buck1 { > > + regulator-name = "vddcore"; > > + regulator-min-microvolt = <1200000>; > > + regulator-max-microvolt = <1350000>; > > + regulator-always-on; > > + regulator-initial-mode = <0>; > > + regulator-over-current-protection; > > + }; > > + > > + vdd_ddr: buck2 { > > + regulator-name = "vdd_ddr"; > > + regulator-min-microvolt = <1350000>; > > + regulator-max-microvolt = <1350000>; > > + regulator-always-on; > > + regulator-initial-mode = <0>; > > + regulator-over-current-protection; > > + }; > > + > > + vdd: buck3 { > > + regulator-name = "vdd"; > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-always-on; > > + st,mask_reset; > > + regulator-initial-mode = <0>; > > + regulator-over-current-protection; > > + }; > > + > > + v3v3: buck4 { > > + regulator-name = "v3v3"; > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-always-on; > > + regulator-over-current-protection; > > + regulator-initial-mode = <0>; > > + }; > > + > > + vdda: ldo1 { > > + regulator-name = "vdda"; > > + regulator-min-microvolt = <2900000>; > > + regulator-max-microvolt = <2900000>; > > + interrupts = <IT_CURLIM_LDO1 0>; > > + interrupt-parent = <&pmic>; > > + }; > > + > > + v2v8: ldo2 { > > + regulator-name = "v2v8"; > > + regulator-min-microvolt = <2800000>; > > + regulator-max-microvolt = <2800000>; > > + interrupts = <IT_CURLIM_LDO2 0>; > > + interrupt-parent = <&pmic>; > > + }; > > + > > + vtt_ddr: ldo3 { > > + regulator-name = "vtt_ddr"; > > + regulator-min-microvolt = <500000>; > > + regulator-max-microvolt = <750000>; > > + regulator-always-on; > > + regulator-over-current-protection; > > + }; > > + > > + vdd_usb: ldo4 { > > + regulator-name = "vdd_usb"; > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3300000>; > > + interrupts = <IT_CURLIM_LDO4 0>; > > + interrupt-parent = <&pmic>; > > + }; > > + > > + vdd_sd: ldo5 { > > + regulator-name = "vdd_sd"; > > + regulator-min-microvolt = <2900000>; > > + regulator-max-microvolt = <2900000>; > > + interrupts = <IT_CURLIM_LDO5 0>; > > + interrupt-parent = <&pmic>; > > + regulator-boot-on; > > + }; > > + > > + v1v8: ldo6 { > > + regulator-name = "v1v8"; > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <1800000>; > > + interrupts = <IT_CURLIM_LDO6 0>; > > + interrupt-parent = <&pmic>; > > + regulator-enable-ramp-delay = <300000>; > > + }; > > + > > + vref_ddr: vref_ddr { > > + regulator-name = "vref_ddr"; > > + regulator-always-on; > > + regulator-over-current-protection; > > + }; > > + > > + bst_out: boost { > > + regulator-name = "bst_out"; > > + interrupts = <IT_OCP_BOOST 0>; > > + interrupt-parent = <&pmic>; > > + }; > > + > > + vbus_otg: pwr_sw1 { > > + regulator-name = "vbus_otg"; > > + interrupts = <IT_OCP_OTG 0>; > > + interrupt-parent = <&pmic>; > > + regulator-active-discharge; > > + }; > > + > > + vbus_sw: pwr_sw2 { > > + regulator-name = "vbus_sw"; > > + interrupts = <IT_OCP_SWOUT 0>; > > + interrupt-parent = <&pmic>; > > + regulator-active-discharge; > > + }; > > + }; > > + > > + onkey { > > + compatible = "st,stpmic1-onkey"; > > + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>; > > + interrupt-names = "onkey-falling", "onkey-rising"; > > + status = "okay"; > > + }; > > + > > + watchdog { > > + compatible = "st,stpmic1-wdt"; > > + status = "disabled"; > > + }; > > + }; > > +}; > > + > > +&iwdg2 { > > + timeout-sec = <32>; > > + status = "okay"; > > +}; > > + > > +&rng1 { > > + status = "okay"; > > +}; > > + > > +&rtc { > > + status = "okay"; > > +}; > > + > > +&sdmmc1 { > > + pinctrl-names = "default", "opendrain", "sleep"; > > + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>; > > + pinctrl-1 = <&sdmmc1_b4_od_pins_a>; > > + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; > > + broken-cd; > > + st,sig-dir; > > + st,neg-edge; > > + st,use-ckin; > > + bus-width = <4>; > > + vmmc-supply = <&vdd_sd>; > > + status = "okay"; > > +}; > > + > > +&uart4 { > > + /* On Low speed expansion header */ > > + label = "LS-UART1"; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&uart4_pins_b>; > > + status = "okay"; > > +}; > > + > > +&uart7 { > > + /* On Low speed expansion header */ > > + label = "LS-UART0"; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&uart7_pins_a>; > > + status = "okay"; > > +}; > > ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 3/3] ARM: dts: Add Avenger96 devicetree support based on STM32MP157A @ 2019-05-06 10:00 ` Manivannan Sadhasivam 0 siblings, 0 replies; 18+ messages in thread From: Manivannan Sadhasivam @ 2019-05-06 10:00 UTC (permalink / raw) To: Alexandre Torgue Cc: devicetree, loic.pallardy, linux-kernel, robh+dt, mcoquelin.stm32, linux-stm32, linux-arm-kernel Hi Alex, On Fri, May 03, 2019 at 11:01:00AM +0200, Alexandre Torgue wrote: > Hi Mani > > On 5/3/19 7:31 AM, Manivannan Sadhasivam wrote: > > Add devicetree support for Avenger96 board based on STM32MP157A MPU > > from ST Micro. This board is one of the 96Boards Consumer Edition board > > from Arrow Electronics and has the following features: > > > > SoC: STM32MP157AAC > > PMIC: STPMIC1A > > RAM: 1024 Mbyte @ 533MHz > > Storage: eMMC v4.51: 8 Gbyte > > microSD Socket: UHS-1 v3.01 > > Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant > > Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac > > Bluetooth®v4.2 (BR/EDR/BLE) > > USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG > > Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4 > > LED: 4x User LED, 1x WiFi LED, 1x BT LED > > > > More information about this board can be found in 96Boards website: > > https://www.96boards.org/product/avenger96/ > > > > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > > --- > > arch/arm/boot/dts/Makefile | 1 + > > arch/arm/boot/dts/stm32mp157a-avenger96.dts | 320 ++++++++++++++++++++ > > 2 files changed, 321 insertions(+) > > create mode 100644 arch/arm/boot/dts/stm32mp157a-avenger96.dts > > > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > > index 8a1d0b3f55dd..f1d2f0bfa7c2 100644 > > --- a/arch/arm/boot/dts/Makefile > > +++ b/arch/arm/boot/dts/Makefile > > @@ -965,6 +965,7 @@ dtb-$(CONFIG_ARCH_STM32) += \ > > stm32h743i-eval.dtb \ > > stm32h743i-disco.dtb \ > > stm32mp157a-dk1.dtb \ > > + stm32mp157a-avenger96.dtb \ > > follow alphabetic order please. > Ack > > stm32mp157c-dk2.dtb \ > > stm32mp157c-ed1.dtb \ > > stm32mp157c-ev1.dtb > > diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts > > new file mode 100644 > > index 000000000000..a3b8af82ac70 > > --- /dev/null > > +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts > > @@ -0,0 +1,320 @@ > > +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) > > +/* > > + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved > > + * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > > + */ > > + > > +/dts-v1/; > > + > > +#include "stm32mp157c.dtsi" > > +#include "stm32mp157-pinctrl.dtsi" > > +#include <dt-bindings/gpio/gpio.h> > > +#include <dt-bindings/mfd/st,stpmic1.h> > > + > > +/ { > > + model = "Arrow Electronics STM32MP157A Avenger96 board"; > > + compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157"; > > + > > + aliases { > > + ethernet0 = ðernet0; > > + mmc0 = &sdmmc1; > > + serial0 = &uart4; > > + serial1 = &uart7; > > + }; > > + > > + chosen { > > + stdout-path = "serial0:115200n8"; > > + }; > > + > > + memory@c0000000 { > > + reg = <0xc0000000 0x40000000>; > > you could add device_type = "memory"; > Ack. Thanks, Mani > > + }; > > + > > + led { > > + compatible = "gpio-leds"; > > + led1 { > > + label = "green:user1"; > > + gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>; > > + linux,default-trigger = "heartbeat"; > > + default-state = "off"; > > + }; > > + > > + led2 { > > + label = "green:user2"; > > + gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>; > > + linux,default-trigger = "mmc0"; > > + default-state = "off"; > > + }; > > + > > + led3 { > > + label = "green:user3"; > > + gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>; > > + linux,default-trigger = "mmc1"; > > + default-state = "off"; > > + }; > > + > > + led4 { > > + label = "green:user3"; > > + gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>; > > + linux,default-trigger = "none"; > > + default-state = "off"; > > + panic-indicator; > > + }; > > + > > + led5 { > > + label = "yellow:wifi"; > > + gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>; > > + linux,default-trigger = "phy0tx"; > > + default-state = "off"; > > + }; > > + > > + led6 { > > + label = "blue:bt"; > > + gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>; > > + linux,default-trigger = "bluetooth-power"; > > + default-state = "off"; > > + }; > > + }; > > +}; > > + > > +ðernet0 { > > + status = "okay"; > > + pinctrl-0 = <ðernet0_rgmii_pins_a>; > > + pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>; > > + pinctrl-names = "default", "sleep"; > > + phy-mode = "rgmii"; > > + max-speed = <1000>; > > + phy-handle = <&phy0>; > > + > > + mdio0 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + compatible = "snps,dwmac-mdio"; > > + phy0: ethernet-phy@7 { > > + reg = <7>; > > + }; > > + }; > > +}; > > + > > +&i2c1 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&i2c1_pins_b>; > > + i2c-scl-rising-time-ns = <185>; > > + i2c-scl-falling-time-ns = <20>; > > + status = "okay"; > > + /delete-property/dmas; > > + /delete-property/dma-names; > > +}; > > + > > +&i2c2 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&i2c2_pins_b>; > > + i2c-scl-rising-time-ns = <185>; > > + i2c-scl-falling-time-ns = <20>; > > + status = "okay"; > > + /delete-property/dmas; > > + /delete-property/dma-names; > > +}; > > + > > +&i2c4 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&i2c4_pins_a>; > > + i2c-scl-rising-time-ns = <185>; > > + i2c-scl-falling-time-ns = <20>; > > + status = "okay"; > > + /delete-property/dmas; > > + /delete-property/dma-names; > > + > > + pmic: stpmic@33 { > > + compatible = "st,stpmic1"; > > + reg = <0x33>; > > + interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>; > > + interrupt-controller; > > + #interrupt-cells = <2>; > > + status = "okay"; > > + > > + st,main-control-register = <0x04>; > > + st,vin-control-register = <0xc0>; > > + st,usb-control-register = <0x30>; > > + > > + regulators { > > + compatible = "st,stpmic1-regulators"; > > + > > + ldo1-supply = <&v3v3>; > > + ldo2-supply = <&v3v3>; > > + ldo3-supply = <&vdd_ddr>; > > + ldo5-supply = <&v3v3>; > > + ldo6-supply = <&v3v3>; > > + pwr_sw1-supply = <&bst_out>; > > + pwr_sw2-supply = <&bst_out>; > > + > > + vddcore: buck1 { > > + regulator-name = "vddcore"; > > + regulator-min-microvolt = <1200000>; > > + regulator-max-microvolt = <1350000>; > > + regulator-always-on; > > + regulator-initial-mode = <0>; > > + regulator-over-current-protection; > > + }; > > + > > + vdd_ddr: buck2 { > > + regulator-name = "vdd_ddr"; > > + regulator-min-microvolt = <1350000>; > > + regulator-max-microvolt = <1350000>; > > + regulator-always-on; > > + regulator-initial-mode = <0>; > > + regulator-over-current-protection; > > + }; > > + > > + vdd: buck3 { > > + regulator-name = "vdd"; > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-always-on; > > + st,mask_reset; > > + regulator-initial-mode = <0>; > > + regulator-over-current-protection; > > + }; > > + > > + v3v3: buck4 { > > + regulator-name = "v3v3"; > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-always-on; > > + regulator-over-current-protection; > > + regulator-initial-mode = <0>; > > + }; > > + > > + vdda: ldo1 { > > + regulator-name = "vdda"; > > + regulator-min-microvolt = <2900000>; > > + regulator-max-microvolt = <2900000>; > > + interrupts = <IT_CURLIM_LDO1 0>; > > + interrupt-parent = <&pmic>; > > + }; > > + > > + v2v8: ldo2 { > > + regulator-name = "v2v8"; > > + regulator-min-microvolt = <2800000>; > > + regulator-max-microvolt = <2800000>; > > + interrupts = <IT_CURLIM_LDO2 0>; > > + interrupt-parent = <&pmic>; > > + }; > > + > > + vtt_ddr: ldo3 { > > + regulator-name = "vtt_ddr"; > > + regulator-min-microvolt = <500000>; > > + regulator-max-microvolt = <750000>; > > + regulator-always-on; > > + regulator-over-current-protection; > > + }; > > + > > + vdd_usb: ldo4 { > > + regulator-name = "vdd_usb"; > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3300000>; > > + interrupts = <IT_CURLIM_LDO4 0>; > > + interrupt-parent = <&pmic>; > > + }; > > + > > + vdd_sd: ldo5 { > > + regulator-name = "vdd_sd"; > > + regulator-min-microvolt = <2900000>; > > + regulator-max-microvolt = <2900000>; > > + interrupts = <IT_CURLIM_LDO5 0>; > > + interrupt-parent = <&pmic>; > > + regulator-boot-on; > > + }; > > + > > + v1v8: ldo6 { > > + regulator-name = "v1v8"; > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <1800000>; > > + interrupts = <IT_CURLIM_LDO6 0>; > > + interrupt-parent = <&pmic>; > > + regulator-enable-ramp-delay = <300000>; > > + }; > > + > > + vref_ddr: vref_ddr { > > + regulator-name = "vref_ddr"; > > + regulator-always-on; > > + regulator-over-current-protection; > > + }; > > + > > + bst_out: boost { > > + regulator-name = "bst_out"; > > + interrupts = <IT_OCP_BOOST 0>; > > + interrupt-parent = <&pmic>; > > + }; > > + > > + vbus_otg: pwr_sw1 { > > + regulator-name = "vbus_otg"; > > + interrupts = <IT_OCP_OTG 0>; > > + interrupt-parent = <&pmic>; > > + regulator-active-discharge; > > + }; > > + > > + vbus_sw: pwr_sw2 { > > + regulator-name = "vbus_sw"; > > + interrupts = <IT_OCP_SWOUT 0>; > > + interrupt-parent = <&pmic>; > > + regulator-active-discharge; > > + }; > > + }; > > + > > + onkey { > > + compatible = "st,stpmic1-onkey"; > > + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>; > > + interrupt-names = "onkey-falling", "onkey-rising"; > > + status = "okay"; > > + }; > > + > > + watchdog { > > + compatible = "st,stpmic1-wdt"; > > + status = "disabled"; > > + }; > > + }; > > +}; > > + > > +&iwdg2 { > > + timeout-sec = <32>; > > + status = "okay"; > > +}; > > + > > +&rng1 { > > + status = "okay"; > > +}; > > + > > +&rtc { > > + status = "okay"; > > +}; > > + > > +&sdmmc1 { > > + pinctrl-names = "default", "opendrain", "sleep"; > > + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>; > > + pinctrl-1 = <&sdmmc1_b4_od_pins_a>; > > + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; > > + broken-cd; > > + st,sig-dir; > > + st,neg-edge; > > + st,use-ckin; > > + bus-width = <4>; > > + vmmc-supply = <&vdd_sd>; > > + status = "okay"; > > +}; > > + > > +&uart4 { > > + /* On Low speed expansion header */ > > + label = "LS-UART1"; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&uart4_pins_b>; > > + status = "okay"; > > +}; > > + > > +&uart7 { > > + /* On Low speed expansion header */ > > + label = "LS-UART0"; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&uart7_pins_a>; > > + status = "okay"; > > +}; > > _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 18+ messages in thread
end of thread, other threads:[~2019-05-06 10:01 UTC | newest] Thread overview: 18+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2019-05-03 5:31 [PATCH 0/3] Add Avenger96 board support Manivannan Sadhasivam 2019-05-03 5:31 ` Manivannan Sadhasivam 2019-05-03 5:31 ` [PATCH 1/3] dt-bindings: arm: stm32: Document Avenger96 devicetree binding Manivannan Sadhasivam 2019-05-03 5:31 ` Manivannan Sadhasivam 2019-05-03 5:31 ` [PATCH 2/3] ARM: dts: stm32mp157: Add missing pinctrl definitions Manivannan Sadhasivam 2019-05-03 5:31 ` Manivannan Sadhasivam 2019-05-03 7:13 ` Alexandre Torgue 2019-05-03 7:13 ` Alexandre Torgue 2019-05-03 7:13 ` Alexandre Torgue 2019-05-06 9:59 ` Manivannan Sadhasivam 2019-05-06 9:59 ` Manivannan Sadhasivam 2019-05-03 5:31 ` [PATCH 3/3] ARM: dts: Add Avenger96 devicetree support based on STM32MP157A Manivannan Sadhasivam 2019-05-03 5:31 ` Manivannan Sadhasivam 2019-05-03 9:01 ` Alexandre Torgue 2019-05-03 9:01 ` Alexandre Torgue 2019-05-03 9:01 ` Alexandre Torgue 2019-05-06 10:00 ` Manivannan Sadhasivam 2019-05-06 10:00 ` Manivannan Sadhasivam
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.