From: Avi Kivity <avi@redhat.com>
To: Jon Mason <mason@myri.com>
Cc: Sven Schnelle <svens@stackframe.org>,
Simon Kirby <sim@hostway.ca>,
Eric Dumazet <eric.dumazet@gmail.com>,
Niels Ole Salscheider <niels_ole@salscheider-online.de>,
Jesse Barnes <jbarnes@virtuousgeek.org>,
Linus Torvalds <torvalds@linux-foundation.org>,
linux-kernel <linux-kernel@vger.kernel.org>,
"linux-pci@vger.kernel.org" <linux-pci@vger.kernel.org>
Subject: Re: [REGRESSION] e1000e failure triggered by "PCI: Remove MRRS modification from MPS setting code"
Date: Tue, 27 Sep 2011 21:28:06 +0300 [thread overview]
Message-ID: <4E8215B6.1020108@redhat.com> (raw)
In-Reply-To: <CAPoiz9w4LyTkmAACHQYR5GSJ+TmN7ePJSb-UuRQ7EjY=QYVn5Q@mail.gmail.com>
On 09/27/2011 08:59 PM, Jon Mason wrote:
> On Tue, Sep 27, 2011 at 12:01 PM, Avi Kivity<avi@redhat.com> wrote:
> > Commit ed2888e906b567 (merged 3.1-rc6) causes a reproducible failure with my
> > e1000e card here. Starting a kvm guest (which mostly consists of shoving
> > display updates over X over ssh, as far as the network is concerned) locks
> > up the card hard.
> >
> > The failure is easily reproducible, will gladly test patches.
>
> Does the problem occur with the adapter assigned to the kvm guest or
> the host?
The host. It's not even using vhost-net or tap or bridge. In fact the
failure happens before the guest has set up neworking itself (in grub,
while clearing the screen); all of the networking load is due to
tunnelling X over ssh.
> I assume that you are running with the default behavior and
> not with the boot arg "pci=pcie_bus_perf".
Correct.
> Can you get the dmesg
> output (specifically the lines that have "Dev MPS")
(this is with the patch reverted)
Sep 27 20:42:48 violet-regb kernel: pci 0000:02:02.0: PCI bridge to [bus
04-04]
Sep 27 20:42:48 violet-regb kernel: pci 0000:01:00.3: PCI bridge to [bus
05-05]
Sep 27 20:42:48 violet-regb kernel: pci 0000:00:03.0: PCI bridge to [bus
06-06]
Sep 27 20:42:48 violet-regb kernel: pci 0000:00:1c.0: PCI bridge to [bus
07-07]
Sep 27 20:42:48 violet-regb kernel: pci 0000:00:1e.0: PCI bridge to [bus
08-08] (subtractive decode)
Sep 27 20:42:48 violet-regb kernel: pci 0000:00:02.0: Dev MPS 128 MPSS
256 MRRS 128
Sep 27 20:42:48 violet-regb kernel: pci 0000:00:02.0: Dev MPS 256 MPSS
256 MRRS 128
Sep 27 20:42:48 violet-regb kernel: pci 0000:01:00.0: Dev MPS 128 MPSS
256 MRRS 4096
Sep 27 20:42:48 violet-regb kernel: pci 0000:01:00.0: Dev MPS 256 MPSS
256 MRRS 128
Sep 27 20:42:48 violet-regb kernel: pci 0000:02:00.0: Dev MPS 128 MPSS
256 MRRS 2048
Sep 27 20:42:48 violet-regb kernel: pci 0000:02:00.0: Dev MPS 256 MPSS
256 MRRS 128
Sep 27 20:42:48 violet-regb kernel: pci 0000:02:02.0: Dev MPS 128 MPSS
256 MRRS 2048
Sep 27 20:42:48 violet-regb kernel: pci 0000:02:02.0: Dev MPS 256 MPSS
256 MRRS 128
Sep 27 20:42:48 violet-regb kernel: pci 0000:04:00.0: Dev MPS 128 MPSS
256 MRRS 512
Sep 27 20:42:48 violet-regb kernel: pci 0000:04:00.0: Dev MPS 256 MPSS
256 MRRS 128
Sep 27 20:42:48 violet-regb kernel: pci 0000:04:00.1: Dev MPS 128 MPSS
256 MRRS 512
Sep 27 20:42:48 violet-regb kernel: pci 0000:04:00.1: Dev MPS 256 MPSS
256 MRRS 128
Sep 27 20:42:48 violet-regb kernel: pci 0000:01:00.3: Dev MPS 256 MPSS
256 MRRS 256
Sep 27 20:42:48 violet-regb kernel: pci 0000:01:00.3: Dev MPS 256 MPSS
256 MRRS 256
Sep 27 20:42:48 violet-regb kernel: pci 0000:00:03.0: Dev MPS 128 MPSS
256 MRRS 128
Sep 27 20:42:48 violet-regb kernel: pci 0000:00:03.0: Dev MPS 256 MPSS
256 MRRS 128
Sep 27 20:42:48 violet-regb kernel: pci 0000:00:1c.0: Dev MPS 128 MPSS
128 MRRS 128
Sep 27 20:42:48 violet-regb kernel: pci 0000:00:1c.0: Dev MPS 128 MPSS
128 MRRS 128
Sep 27 20:42:48 violet-regb kernel: pci0000:00: Requesting ACPI _OSC
control (0x1d)
Sep 27 20:42:48 violet-regb kernel: pci0000:00: ACPI _OSC request failed
(AE_NOT_FOUND), returned control mask: 0x1d
Sep 27 20:42:48 violet-regb kernel: ACPI _OSC control for PCIe not
granted, disabling ASPM
Sep 27 20:42:48 violet-regb kernel: ACPI: PCI Interrupt Link [LNKA]
(IRQs 3 4 5 6 *7 10 11 14 15)
Sep 27 20:42:48 violet-regb kernel: ACPI: PCI Interrupt Link [LNKB]
(IRQs 3 4 *5 6 7 10 11 14 15)
Sep 27 20:42:48 violet-regb kernel: ACPI: PCI Interrupt Link [LNKC]
(IRQs 3 4 5 6 7 *10 11 14 15)
Sep 27 20:42:48 violet-regb kernel: ACPI: PCI Interrupt Link [LNKD]
(IRQs 3 4 5 6 7 10 *11 14 15)
Sep 27 20:42:48 violet-regb kernel: ACPI: PCI Interrupt Link [LNKE]
(IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
Sep 27 20:42:48 violet-regb kernel: ACPI: PCI Interrupt Link [LNKF]
(IRQs 4 5 6 7 10 11 14 15) *0, disabled.
Sep 27 20:42:48 violet-regb kernel: ACPI: PCI Interrupt Link [LNKG]
(IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
> and lspci -vvv on
> the host?
# lspci -vvv
00:00.0 Host bridge: Intel Corporation 5000V Chipset Memory Controller
Hub (rev 92)
Subsystem: Tyan Computer Device 5372
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 0
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] MSI: Enable- Count=1/2 Maskable- 64bit-
Address: fee00000 Data: 0000
Capabilities: [6c] Express (v1) Root Port (Slot-), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s, Latency
L0 unlimited, L1 unlimited
ClockPM- Surprise+ LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+
DLActive+ BWMgmt- ABWMgmt-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol+
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol+
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 15, GenCap- CGenEn- ChkCap- ChkEn-
00:02.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8
Port 2-3 (rev 92) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=05, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: df100000-df2fffff
Prefetchable memory behind bridge: 00000000d0000000-00000000d00fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] MSI: Enable- Count=1/2 Maskable- 64bit-
Address: fee00000 Data: 0000
Capabilities: [6c] Express (v1) Root Port (Slot-), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x8, ASPM L0s, Latency
L0 unlimited, L1 unlimited
ClockPM- Surprise+ LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+
DLActive+ BWMgmt- ABWMgmt-
RootCtl: ErrCorrectable+ ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Kernel driver in use: pcieport
00:03.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4
Port 3 (rev 92) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] MSI: Enable- Count=1/2 Maskable- 64bit-
Address: fee00000 Data: 0000
Capabilities: [6c] Express (v1) Root Port (Slot-), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #3, Speed 2.5GT/s, Width x4, ASPM L0s, Latency
L0 unlimited, L1 unlimited
ClockPM- Surprise+ LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
RootCtl: ErrCorrectable+ ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Kernel driver in use: pcieport
00:08.0 System peripheral: Intel Corporation 5000 Series Chipset DMA
Engine (rev 92)
Subsystem: Intel Corporation Device 8086
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 0
Region 0: Memory at fe700000 (64-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: fee00000 Data: 0000
Capabilities: [6c] Express (v1) Root Complex Integrated Endpoint,
MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal+
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown,
Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk-
DLActive- BWMgmt- ABWMgmt-
00:10.0 Host bridge: Intel Corporation 5000 Series Chipset FSB Registers
(rev 92)
Subsystem: Intel Corporation Device 8086
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:10.1 Host bridge: Intel Corporation 5000 Series Chipset FSB Registers
(rev 92)
Subsystem: Intel Corporation Device 8086
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:10.2 Host bridge: Intel Corporation 5000 Series Chipset FSB Registers
(rev 92)
Subsystem: Intel Corporation Device 8086
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:11.0 Host bridge: Intel Corporation 5000 Series Chipset Reserved
Registers (rev 92)
Subsystem: Intel Corporation Device 8086
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:13.0 Host bridge: Intel Corporation 5000 Series Chipset Reserved
Registers (rev 92)
Subsystem: Intel Corporation Device 8086
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:15.0 Host bridge: Intel Corporation 5000 Series Chipset FBD Registers
(rev 92)
Subsystem: Intel Corporation Device 8086
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:16.0 Host bridge: Intel Corporation 5000 Series Chipset FBD Registers
(rev 92)
Subsystem: Intel Corporation Device 8086
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:1c.0 PCI bridge: Intel Corporation 631xESB/632xESB/3100 Chipset PCI
Express Root Port 1 (rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: d0100000-d02fffff
Prefetchable memory behind bridge: 00000000d0300000-00000000d04fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
unlimited, L1 unlimited
ExtTag+ RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x4, ASPM L0s L1,
Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+
Surprise+
Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn+ PwrFlt- MRL- PresDet+ CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet-
Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0300c Data: 4151
Capabilities: [90] Subsystem: Tyan Computer Device 5372
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable- ID=0 ArbSelect=Fixed TC/VC=00
Status: NegoPending- InProgress-
Capabilities: [180 v1] Root Complex Link
Desc: PortNumber=01 ComponentID=02 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=02 AssocRCRB-
LinkType=MemMapped LinkValid+
Addr: 00000000fed1c001
Kernel driver in use: pcieport
00:1d.0 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset
UHCI USB Controller #1 (rev 09) (prog-if 00 [UHCI])
Subsystem: Tyan Computer Device 5372
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 4: I/O ports at 1800 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset
UHCI USB Controller #2 (rev 09) (prog-if 00 [UHCI])
Subsystem: Tyan Computer Device 5372
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 1820 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset
UHCI USB Controller #3 (rev 09) (prog-if 00 [UHCI])
Subsystem: Tyan Computer Device 5372
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 1840 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset
UHCI USB Controller #4 (rev 09) (prog-if 00 [UHCI])
Subsystem: Tyan Computer Device 5372
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 1860 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset
EHCI USB2 Controller (rev 09) (prog-if 20 [EHCI])
Subsystem: Intel Corporation 631xESB/632xESB/3100 Chipset EHCI USB2
Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: Memory at df500000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d9) (prog-if
01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=08, subordinate=08, sec-latency=32
I/O behind bridge: 00003000-00003fff
Memory behind bridge: df000000-df0fffff
Prefetchable memory behind bridge: 00000000de000000-00000000deffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Tyan Computer Device 5372
00:1f.0 ISA bridge: Intel Corporation 631xESB/632xESB/3100 Chipset LPC
Interface Controller (rev 09)
Subsystem: Tyan Computer Device 5372
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:1f.2 IDE interface: Intel Corporation 631xESB/632xESB/3100 Chipset
SATA IDE Controller (rev 09) (prog-if 80 [Master])
Subsystem: Tyan Computer Device 5372
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 18b0 [size=16]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ata_piix
Kernel modules: ata_generic, pata_acpi
00:1f.3 SMBus: Intel Corporation 631xESB/632xESB/3100 Chipset SMBus
Controller (rev 09)
Subsystem: Tyan Computer Device 5372
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 1100 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
01:00.0 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express
Upstream Port (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=01, secondary=02, subordinate=04, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: df200000-df2fffff
Prefetchable memory behind bridge: 00000000d0000000-00000000d00fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [44] Express (v1) Upstream Port, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE-
FLReset-SlotPowerLimit 0.000W
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s, Latency
L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Subsystem: Tyan Computer Device 5372
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn-
Kernel driver in use: pcieport
01:00.3 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express to
PCI-X Bridge (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=01, secondary=05, subordinate=05, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [44] Express (v1) PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal+
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- BrConfRtry-
MaxPayload 256 bytes, MaxReadReq 256 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s, Latency
L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk-
DLActive- BWMgmt- ABWMgmt-
Capabilities: [6c] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Subsystem: Tyan Computer Device 5372
Capabilities: [d8] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz
Status: Dev=00:00.3 64bit- 133MHz- SCD- USC- SCO- SRD-
Upstream: Capacity=65535 CommitmentLimit=65535
Downstream: Capacity=65535 CommitmentLimit=65535
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn-
02:00.0 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express
Downstream Port E1 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=02, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [44] Express (v1) Downstream Port (Slot-), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s, Latency
L0 <512ns, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Subsystem: Tyan Computer Device 5372
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Kernel driver in use: pcieport
02:02.0 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express
Downstream Port E3 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=02, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: df200000-df2fffff
Prefetchable memory behind bridge: 00000000d0000000-00000000d00fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [44] Express (v1) Downstream Port (Slot-), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s, Latency
L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Subsystem: Tyan Computer Device 5372
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Kernel driver in use: pcieport
04:00.0 Ethernet controller: Intel Corporation 80003ES2LAN Gigabit
Ethernet Controller (Copper) (rev 01)
Subsystem: Tyan Computer Device 5300
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 65
Region 0: Memory at df220000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at df200000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 2000 [size=32]
[virtual] Expansion ROM at d0000000 [disabled] [size=64K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0100c Data: 4179
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
<512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1,
Latency L0 <128ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO+ CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-e0-81-ff-ff-44-3f-4e
Kernel driver in use: e1000e
Kernel modules: e1000e
04:00.1 Ethernet controller: Intel Corporation 80003ES2LAN Gigabit
Ethernet Controller (Copper) (rev 01)
Subsystem: Tyan Computer Device 5300
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 66
Region 0: Memory at df260000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at df240000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 2020 [size=32]
[virtual] Expansion ROM at d0010000 [disabled] [size=64K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0200c Data: 4189
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
<512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1,
Latency L0 <128ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-e0-81-ff-ff-44-3f-4e
Kernel driver in use: e1000e
Kernel modules: e1000e
08:01.0 VGA compatible controller: XGI Technology Inc. (eXtreme Graphics
Innovation) Z7/Z9 (XG20 core) (prog-if 00 [VGA controller])
Subsystem: XGI Technology Inc. (eXtreme Graphics Innovation) Z7/Z9
(XG20 core)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
BIST result: 00
Region 0: Memory at de000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at df000000 (32-bit, non-prefetchable) [size=256K]
Region 2: I/O ports at 3000 [size=128]
Expansion ROM at <unassigned> [disabled]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
08:02.0 Ethernet controller: Intel Corporation 82557/8/9/0/1 Ethernet
Pro 100 (rev 10)
Subsystem: Intel Corporation EtherExpress PRO/100 S Server Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 66 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at df060000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 3080 [size=64]
Region 2: Memory at df040000 (32-bit, non-prefetchable) [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
> Is this an e1000e 4port adapter?
Dual port.
--
I have a truly marvellous patch that fixes the bug which this
signature is too narrow to contain.
next prev parent reply other threads:[~2011-09-27 18:28 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-09-27 17:01 [REGRESSION] e1000e failure triggered by "PCI: Remove MRRS modification from MPS setting code" Avi Kivity
2011-09-27 17:59 ` Jon Mason
2011-09-27 18:28 ` Avi Kivity [this message]
2011-09-27 20:11 ` Jon Mason
2011-09-29 4:33 ` Benjamin Herrenschmidt
2011-09-29 13:53 ` Jon Mason
2011-09-30 0:16 ` Workaround for Intel MPS errata Jon Mason
2011-09-30 2:21 ` Jesse Brandeburg
2011-09-30 2:51 ` Jon Mason
2011-09-30 5:01 ` Bjorn Helgaas
2011-09-30 15:35 ` Jon Mason
2011-09-30 17:17 ` Bjorn Helgaas
2011-09-30 17:38 ` Jon Mason
2011-09-30 17:57 ` Bjorn Helgaas
2011-09-30 7:03 ` Rolf Eike Beer
2011-09-30 15:39 ` Jon Mason
2011-10-02 9:26 ` Avi Kivity
2011-10-03 4:58 ` Jon Mason
2011-10-03 10:11 ` Avi Kivity
2011-10-03 15:12 ` Jon Mason
2011-10-04 9:46 ` Avi Kivity
2011-10-04 13:06 ` Avi Kivity
2011-10-04 13:11 ` Jon Mason
2011-10-04 20:12 ` Jon Mason
2011-10-05 3:46 ` Jon Mason
2011-10-05 12:09 ` Avi Kivity
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4E8215B6.1020108@redhat.com \
--to=avi@redhat.com \
--cc=eric.dumazet@gmail.com \
--cc=jbarnes@virtuousgeek.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=mason@myri.com \
--cc=niels_ole@salscheider-online.de \
--cc=sim@hostway.ca \
--cc=svens@stackframe.org \
--cc=torvalds@linux-foundation.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.